input connectors - Teltherm Instruments

www.ahlborn.com
INPUT CONNECTORS
03
+
Our Tip:
Make the most of your existing sensor technology !
Our patented intelligent connector makes the ALMEMO® measuring system extraordinarily flexible.
Thus, instead of our pre-configured ALMEMO® sensors, you can use your own existing sensors.
We can supply you with ALMEMO® connectors specially pre-programmed for this purpose with the necessary sensor parameters
and the appropriate measuring range. These have six screw terminals and can be easily and conveniently connected.
All devices and connectors offer the following functions :
- Each measuring point can be assigned a specific designation.
- The sensor signals can be scaled.
- Measured values can be corrected for zero-point and gain.
The new measuring instruments with ALMEMO® connectors also offer the following additional functions :
- Multi-point calibration data can be saved in the connector.
- User-defined linearization with up to 30 points can be programmed in the connector.
- Control points with actual / setpoint values tables can be entered quickly and easily via the AMR-Control software.
- Any special measuring ranges programmed in the connector can be processed.
- Calibration schedules can be managed in the connector and are detected automatically.
- The connector’s exact designation can be called up.
The already high level of precision and overall performance quality provided by ALMEMO® measuring technology is thus
raised even further.
Give us a description of your measuring tasks !
And we shall provide you with comprehensive advice and find the most cost-effective solution.
Please do not hesitate to ask !
03.02
01/2011 We reserve the right to make technical changes.
ALMEMO® Connector in Original Size
ALMEMO® Sensor Connector
with 6 Screw Terminals
and EEPROM
03
INPUT CONNECTORS
Linearization and correction at over 30 points performed by the user - without further
processing on the PC
Although special-purpose sensors with a nonlinear output can usually be connected to existing
measuring systems, the lack of linearization in the
sensor’s output signal means that the measured
value will need subsequent correction to make it at all
usable. AHLBORN now offers customers a revolutionary
new feature - also available with hand-held devices. An
option is now available allowing the user to perform
linearization and multi-point correction on ALMEMO®
measuring instruments. Not only all the relevant sensor
characteristics but also the linearization or multi-point correction
data are saved in the patented ALMEMO® connector. The measuring
instrument automatically recognizes each sensor that is connected to it and
shows the appropriate measured values precisely in its display.
Sensor-specific linearization data can be saved by the user in the connector itself.
Thanks to further development of the flexible and intelligent ALMEMO® connector it is now possible to save
complex tables for linearization or multi-point correction - all in the connector itself. For the user this means that it
is now also possible to connect sensors with a non-linear output. The device displays measured values already in
linearized form; this ensures that the whole process can be monitored right from the outset. A further advantage
is the enormous saving in time when evaluating special measuring operations of this nature. For each sensor the
linearization data is saved in the connector; then as soon as the sensor is plugged into the measuring instrument this data is
loaded automatically. The linearization table is buffered in the main working memory on the device for the period of the
measuring operation in question or for as long as the sensor remains connected. With effect from the ALMEMO® 2690-8 the
user can use this “KL” option to program linearization processes of this nature quickly and easily. Individual linearization
processes can be applied in the voltage, current, resistance, or frequency ranges. On request - or for other devices - readily
pre-programmed connectors can be obtained from the factory. Various already implemented special-purpose linearizations
are also available.
High-precision measuring operations - thanks to multi-point correction
A sensor’s output signal can also be corrected at various specific points. Inexpensive standard sensors made by third-party
manufacturers can be calibrated. Deviations are then saved in the sensor connector as fine corrections. This can be
performed either by users themselves or on request in advance at the factory - for example for temperature calibrations. It is
now possible to save not only previous characteristics but also over 30 correction points - all in the connector itself.
Programming via software
In the AMR-CONTROL software package the
measuring protocol for a multi-point correction or a
linearization table can be transferred to a table of
reference points. Over 30 such reference points are
possible. During a measuring operation the
measured values between these are interpolated on
a linear basis. The AMR-CONTROL software is
included with all our instruments free-of-charge.
System requirements
Connector - the new generation (code “E4”)
For evaluation purposes : ALMEMO® devices in version V6
(2690-8, 2890-8, 8590, 8690, 5690, 2390-8, and 2390-5/S)
For user-defined programming : Option “KL” with devices
2690-8, 2890-9,8590, 8690, and 5690
01/2011 We reserve the right to make technical changes.
High-precision measuring operations using inexpensive standard sensors thanks to multi-point correction
Linearization and correction of non-linear sensors
www.ahlborn.com
03.03
www.ahlborn.com
INPUT CONNECTORS
03
ALMEMO® Connectors for Thermocouple Types K, N, L, J, T
Variants ( with thermal material)
Model
Meas. Range
NiCr-Ni (K)
–200.0 to +1370.0°C
NiCroSil-NiSil (N)
–200.0 to +1300.0°C
Fe-CuNi (L)
–200.0 to +900 °C,
Fe-CuNi (J)
–200.0 to +1000 °C,
Cu-CuNi (T)
–200.0 to +400 °C,
Resolution
0.1K
0.1K
0.1 K
0.1 K
0.1 K
Order no. ZA9020FS
Order no. ZA9021FSN
Order no. ZA9021FSL
Order no. ZA9021FSJ
Order no. ZA9021FST
ALMEMO®-D measuring module for thermocouples,
types K, J, T, electrically isolated, up to 1000 V
Type ZAD 950 AB
03.04
01/2011 We reserve the right to make technical changes.
Technical data:
 Electrically isolated measurement of thermocouples (in
particular bare thermo-wire types) on live parts
 Digital transfer of measured values to the ALMEMO®
measuring instrument
 Connecting cable, fitted with ALMEMO® D plug
 New A wide variety of connection options (see page 09.06)
1. Direct connection to the input of an ALMEMO® measuring
instrument optional ALMEMO® D extension cable, RS422,
up to 100 meters - or over 100 meters using the customer’s
own cable
2. For connection to a PC ALMEMO® USB data cable, with
power supply
3. For connection to an RS422 network ALMEMO® coupling
with RS422 driver
 Sensor connection via 4-mm safety plug (with screw
terminals)
Sensor
Measuring range
ZAD950ABK
ZAD950ABJ
ZAD950ABT
Resolution
Linearization accuracy
A/D converter
Electrical isolation
Sensor connection
Power supply
Current consumption
Connecting cable
Housing
Thermocouple
NiCr-Ni (K) -200 to 1370 °C
Fe-CuNi (J) -200 to 1000 °C
Cu-CuNi (T) -200 to 400 °C
0.1 K
±0.5 K ±0.05 % of measured value
delta-sigma, 15-bit resolution
For technical data see page 01.05.
1 kV DC/AC permanent, 4 kV for 1s
4-mm safety sockets and safety plugs
(with screw terminals)
6 to 13 VDC via ALMEMO® device
approx. 30 mA
1.5 meters with ALMEMO® D plug
Dimensions (LxWxH) 127x83x38mm,
ABS (acrylonitrile butadiene styrene)
Types :
ALMEMO® D measuring module for NiCr-Ni (K), including 1.5 meters ALMEMO® D connecting cable
ALMEMO® D measuring module for Fe-CuNi (J) including 1.5 meters ALMEMO® D connecting cable
ALMEMO® D measuring module for Cu-CuNi (T) including 1.5 meters ALMEMO® D connecting cable
Please note : thermocouple must be ordered extra; e.g. thermo-wires see Chapter 08
Order no. ZAD950ABK
Order no. ZAD950ABJ
Order no. ZAD950ABT
03
INPUT CONNECTORS
Types:
Model
Cu-CuNi (U)
PtRh10-Pt (S)
PtRh13-Pt (R)
PtRh30-PtRh6 (B)
AuFe-Cr (A)
Meas. Range
–200.0 to +600.0°C
0.0 to +1760.0°C
0.0 to +1760.0°C
+400.0 to +1800.0°C
–270.0 to +60.0°C
Resolution
0.1K
0.1K
0.1K
0.1K
0.1K
Order no.
Order no.
Order no.
Order no.
Order no.
ZA9000FSU
ZA9000FSS
ZA9000FSR
ZA9000FSB
ZA9000FSA
01/2011 We reserve the right to make technical changes.
ALMEMO® Connectors for Thermocouple Types U, S, R, B, AuFe-Cr
ALMEMO® connector with integrated cold junction sensor for all thermocouples
For especially exacting applications demanding the highest
possible level of precision or performed under unfavorable
conditions (e.g. subject to thermal irradiation)
Programming:
1st channel, NTC, integrated cold junction sensor, resolution 0.01 K
2nd channel, thermocouple, resolution 0.1 K; please specify type !
Types:
Model
NiCr-Ni (K)
NiCroSil-NiSil (N)
Fe-CuNi (L)
Fe-CuNi (J)
Cu-CuNi (T)
Cu-CuNi (U)
PtRh10-Pt (S)
Meas. Range
–200.0 to +1370.0°C,
–200.0 to +1300.0°C,
–200.0 to +900°C,
–200.0 to +1000°C,
–200.0 to +400°C,
–200.0 to +600.0°C
0.0 to +1760.0°C
Resolution
0.1 K
0.1 K
0.1 K
0.1 K
0.1 K
0.1 K
0.1 K
Order no.
Order no.
Order no.
Order no.
Order no.
Order no.
Order no.
ZA9400FSK
ZA9400FSN
ZA9400FSL
ZA9400FSJ
ZA9400FST
ZA9400FSU
ZA9400FSS
ALMEMO® Connectors for Pt100 Sensors/Pt1000 Sensors
Types:
Model
Pt100 4-conductors
Pt100 4-conductors
Pt1000 4-conductors
Pt1000 4-conductors
Pt100 4-conductors
Meas. Range
–200.0 to +850.0°C
–200.0 to +400.0°C*
–200.0 to +850.0°C*
–200.0 to +400.0°C*
-8 to +65.000°C
Resolution
0.1K
0.01K
0.1K
0.01K
0.001K (for ALMEMO® up to 2690-8)
www.ahlborn.com
Order no.
Order no.
Order no.
Order no.
Order no.
ZA9030FS1
ZA9030FS2
ZA9030FS4
ZA9030FS5
ZA9030FS7
*Data may vary depending on device; (see data sheet per device).
03.05
www.ahlborn.com
INPUT CONNECTORS
03
ALMEMO® Connectors for Ni100 Sensors/Ni1000 Sensors
Types:
Model
Ni100
Ni1000
Meas. Range
–60.0 to +240.0°C
–60.0 to +240.0°C
Resolution
0.1K
0.1K
Order no. ZA9030FS3
Order no. ZA9030FS6
Resolution
0.01K
0.01 K no electrical isolation
Order no. ZA9040FS
Order no. ZA9040FS2
ALMEMO® Connectors for Ntc Sensors
03.06
01/2011 We reserve the right to make technical changes.
Types:
Model
Ntc type N
2xNtc type N
Meas. Range
–50.0 to +125.0°C
–50.0 to +125.0°C
ALMEMO® Connectors for Resistance
Technical data ZA 9003 SS4:
Connection
Linearization accuracy:
2-wire
±0,2 % ± 0,02 kOhm
Linearization is saved in the
ALMEMO® connector; (this is not
available with ALMEMO® 2450, 8390)
Types:
Model
Ohm
Ohm
kOhm
Meas. Range
0.00 to 500.00
0.0 to 5000.0
0 to 110.00 kOhm
Resolution
0.01Ω *
0.1Ω *
0.01kΩ
Order no. ZA9003FS
Order no. ZA9003FS2
Order no. ZA9003SS4
*Data may vary depending on device; (see data sheet per device)
03
INPUT CONNECTORS
Sensor supply 2,5V
potentiometer
Technical Data:
Sensor supply:
Temperature coefficient:
Types:
Model
2.6 V DC (differential)
Meas. Range
–2.6 to +2.6 *
Resolution
0.1 mV
2.5 V
< 50 ppm/K
Order no. ZA9025FS3
*Data may vary depending on device; (see data sheet per device)
01/2011 We reserve the right to make technical changes.
ALMEMO® Connectors for Potentiometer pickoffs
ALMEMO® Connectors for Voltage Millivolt
Types:
Model
55mVDC
26mVDC
260mVDC
Meas. Range
–10.0 to +55.0
–26.0 to +26.0
–260.0 to +260.0
Resolution
1μV
1μV
10μV
Order no. ZA9000FS0
Order no. ZA9000FS1
Order no. ZA9000FS2
ALMEMO® Connectors for Volt DC
Technical Data:
Accuracy divider:
Types:
Model
2.6VDC
Meas. Range
–2.6 to +2.6 *
5.5VDC (divider 100:1) –1 to 5.5
26VDC (divider 100:1) –26.0 to +26.0
2 x 26 V DC (2xdivider) –26.0 to +26.0
only 5.5 / 26 V connector,
±0.1% of measured value
Resolution
0.1 mV
Order no. ZA9000FS3
0.1 mV
1 mV
1 mV no electrical isolation
Order no. ZA9602FS4
Order no. ZA9602FS
Order no ZA9602FS2
*Data may vary depending on device; (see data sheet per device)
www.ahlborn.com
03.07
www.ahlborn.com
INPUT CONNECTORS
03
ALMEMO® Connectors for DC Millivolt / Volt Differential
for sensors / transmitters, Supply from ALMEMO® device
Technical Data:
Sensor supply
Accuracy divider:
Types:
Model
55 mV DC
26 mV DC
260 mV DC
2.6 V DC
Meas. Range
–10.0 to +55.0
–26.0 to +26.0
–260.0 to +260.0
–2.6 to +2.6 *
Resolution
1 μV
1 μV
10 μV
0,1 mV
(for voltage see technical data
of ALMEMO® device)
only 26V connector
±0,1% of measured value
Order no.
Order no.
Order no.
Order no.
ZA9000FS0D
ZA9000FS1D
ZA9000FS2D
ZA9000FS3D
(Connection diagram for connectors with 4 clamps, see below)
*Data may vary depending on device; (see data sheet per device)
ALMEMO® Connectors for DC Millivolt / Volt Differential
for sensors / transmitters, Supply : 12 V from the ALMEMO® device
Technical Data:
Sensor supply UF:
Output current:
Accuracy divider:
13.5V ±0.5V
100mA at UG = 12V
50mA at UG = 9V
20mA at UG = 7V
only 26V connector
±0,1% of measured value
(UG = device voltage)
03.08
01/2011 We reserve the right to make technical changes.
Types:
Model
55mV DC
26mV DC
260mV DC
2.6V DC
26V DC
Meas. Range
–10.0 to +55.0
–26.0 to +26.0
–260.0 to +260.0
–2.6 to +2.6 *
-26.0 to +26.0
Resolution
1 μV
1 μV
10 μV
0.1 mV
1 mV
Order no. ZA9600FS0V12
Order no. ZA9600FS1V12
Order no. ZA9600FS2V12
Order no. ZA9600FS3V12
Order no. ZA9602FS3V12
*Data may vary depending on device; (see data sheet per device).
03
INPUT CONNECTORS
With zero-symmetrical voltage supply of ±2.5 V stabilized from the ALMEMO® device
Technical Data:
Bridge circuit
Types:
Model
55mV DC
26mV DC
260mV DC
2.6V DC
Sensor supply:
Voltage UF:
Temperature coefficient:
Output current:
Quiescent current
New
Energy saving
Meas. Range
–10,0 to +55,0
–26,0 to +26,0
–260,0 to +260,0
–2,6 to +2,6*
Resolution
1 μV
1 μV
10 μV
0,1 mV
5V ± 0.05V
<50ppm/°C
max. 100mA
approx. 3 mA
So long as the
measuring point is not
selected, the bridge
voltage remains
switched OFF.
01/2011 We reserve the right to make technical changes.
ALMEMO® input connector for measuring bridges,, millivolt / volt differential
Order no. ZA9105FS0
Order no. ZA9105FS1
Order no. ZA9105FS2
Order no. ZA9105FS3
*Data may vary depending on device; (see data sheet per device)
ALMEMO® Measuring Module for DC Voltage, with Electrical Isolation, 4kV
Technical Data:
see page 12.05
Types:
Measuring range
±2,000 V
±20,00 V
±200,0 V
±400 V
www.ahlborn.com
Resolution
0,001V
0,01V
0,1V
1V
Overload
400 V
500 V
500 V
1000 V
Internal resistance
800 kΩ
1 MΩ
1 MΩ
4 MΩ
Order no.
Order no.
Order no.
Order no.
ZA9900AB2
ZA9900AB3
ZA9900AB4
ZA9900AB5
03.09
www.ahlborn.com
INPUT CONNECTORS
03
ALMEMO® Connectors for DC Current mA
Technical Data:
Accuracy shunt:
Types:
Model
32mA DC
4/20mA DC
2 x 32 mA DC
2 x 4/20 mA DC
Meas. Range
–32.0 to +32.0 *
0 to 100%
–32.0 to +32.0 *
0 to 100%
Resolution
1μA
0.01%
1 μA no electrical isolation
0.01 % no electrical isolation
±0,1% of measured value
Order no.
Order no.
Order no.
Order no.
ZA9601FS1
ZA9601FS2
ZA9601FS3
ZA9601FS4
*Data may vary depending on device; (see data sheet per device).
ALMEMO® Connectors for DC mA Differential
for sensors / transmitters, Supply from the ALMEMO® device
Technical Data:
Sensor supply
Accuracy shunt:
Types:
Model
32 mA DC
4/20 mA DC
Meas. Range
–32.0 to +32.0 *
0 to 100%
Resolution
1 μA
0.01%
(for voltage see technical data
of ALMEMO® device)
±0,1% of measured value
Order no. ZA9601FS5
Order no. ZA9601FS6
03.10
01/2011 We reserve the right to make technical changes.
*Data may vary depending on device; (see data sheet per device)
ALMEMO®Connectors for DC mA Differential
for sensors / transmitters, Supply : 12 V from the ALMEMO® device
Technical Data:
Sensor supply UF:
Output current:
2-wire transmitter
(3-wire transmitter can also be
connected)
Accuracy shunt:
13.5V ±0.5V
100mA at UG = 12V
50mA at UG = 9V
20mA at UG = 7V
±0,1% of measured value
(UG = device voltage)
Types:
Model
32mA DC
4-20mA DC
Meas. Range
–32.0 to +32.0 *
0 to 100%
Resolution
1 μA
0.01 %
ZA9601FS5V12
ZA9601FS6V12
*Data may vary depending on device; (see data sheet per device).
03
INPUT CONNECTORS
01/2011 We reserve the right to make technical changes.
ALMEMO® Measuring Module for DC, with Electrical Isolation, 4kV
Technical Data:
see page 12.05
Types:
Measuring range
±20.00 mA
±200.0 mA
±2.000 A
±10.00 A
Resolution
0.01mA
0.1mA
0.001A
0.01A
DC via external shunt:
±200.0 mV
0.1mV
Overload
Internal resistance
0.1 A*
10 Ω
Order no.
1 A*
1Ω
Order no.
10 A*
0.1 Ω
Order no.
20 A*
0.01 Ω
Order no.
*Without fuse, overload condition only up to 1 minute maximum
40 V
50 kΩ
ZA9901AB1
ZA9901AB2
ZA9901AB3
ZA9901AB4
Order no. ZA9900AB1
ALMEMO® Adapter Cables for AC Voltage
Technical Data:
Frequency range: 50 Hz to 10 kHz
Accuracy:
± 0.2% of final val. ± 0.5% of meas. val.
(40Hz … 2kHz sinusoidal),
Crest factor:
3 (add. error 0.7%), 5 (add. error 2.5%)
+
NEVER connect voltages higher than 50V!
DANGER!
www.ahlborn.com
Types:
Meas. Range
5 to 260mVrms
0.05 to 2.6Vrms
0.5 to 26.0Vrms
Resolution
0.1mV
0.001mV
0.01mV
Order no. ZA9603AK1
Order no. ZA9603AK2
Order no. ZA9603AK3
03.11
www.ahlborn.com
INPUT CONNECTORS
03
ALMEMO® Measuring Module for AC Voltage, with Electrical Isolation, 4kV
Technical Data:
see page 12.06
Types:
Meas. range
Resolution
Peak
Overload
Internal resistance
130.0mVrms
1.300Vrms
13.00Vrms
130.0Vrms
400Vrms
0.1mV
1mV
10mV
0.1V
1V
0.2V
2V
20V
200V
1000V
400V
400V
500V
500V
1000V
0.5MΩ
0.8MΩ
1MΩ
1MΩ
4MΩ
Order no.
Order no.
Order no.
Order no.
Order no.
ZA9903AB1
ZA9903AB2
ZA9903AB3
ZA9903AB4
ZA9903AB5
ALMEMO® Measuring Module for AC, with Electrical Isolation, 4kV
Technical Data:
03.12
01/2011 We reserve the right to make technical changes.
see page 12.06
Types:
Meas. range
1.000Arms
10.00Arms
Resolution
1mA
10mA
Peak
2A
20A
Overload
10A*
20A*
*Without fuse, overload condition only up to 1 minute maximum
Internal resistance
0.10Ω
0.01Ω
Order no. ZA9904AB1
Order no. ZA9904AB2
03
INPUT CONNECTORS
for sensors, Supply : 5 V or direct from ALMEMO® device
Technical Data:
Frequency range:
switch NPNoutput
Types (Cable lengths, 1.5 meters)
Model
Measuring range
Frequency
0 to 15000 Hz
0 to 3200.0 Hz
Pulses / cycle
0 to 65000 pulses
Speed
8 to 32000 rpm
Option : sensor supply 12 V
PNPoutput
0 to 15000 Hz (Resolution 1 Hz)
0 to 3200.0 Hz (Resolution 0.1 Hz)
Speed range:
8 to 32000 rpm (Resolution: 1 rpm)
Max. pulse count:
65000
Pulse length:
> 50 μs
Input voltage
4 to 40 V, square-wave via optocoupler
Current consumption: 3 mA
Sensor supply
5 V or direct from ALMEMO® device
(for voltage see technical data of ALMEMO® device)
Option V12
Sensor supply:
13.5V ±0.5V
Output current:
100mA at UG = 12V
50mA at UG = 9V
20mA at UG = 7V (UG = device voltage)
Resolution
1 Hz
0.1 Hz can, by inserting wire jumper, be switched to
1 pulse
1 rpm
01/2011 We reserve the right to make technical changes.
ALMEMO® Adapter Cables for Frequency / Pulse / Rotational Speed
Order no. ZA9909AK1U
Order no. ZA9909AK2U
Order no. ZA9909AK4U
Order no. OA9909V12
ALMEMO® Adapter Cable for Digital Input Signals
digital inputs
channel 1
channel 2
channel 3
www.ahlborn.com
Types: (cable length, 1.5m each)
3 digital inputs, (optocoupler), for floating contacts, 5V auxiliary voltage led out
Order no. ZA9000ES2
4 digital inputs, electrically isolated (optocoupler) for external voltage, 4 to 30 V
Order no. ZA9000EK2
03.13
www.ahlborn.com
INPUT CONNECTORS
03
ALMEMO® Universal Adapter Cables with Free Ends
Type:
The ALMEMO® universal connector ZA 9000-FS is also available with connecting cable and free ends, as adapter cable ZA9000AK.
The sensor supply voltage is present on terminal U+; it is supplied by the ALMEMO® device (sensor supply voltage 5 V, can be
stabilized on request). Connecting cable : 8-wire, 8 x 0.14 mm2, black, Length 1.5 m The wiring diagram and color code of the wires
are consistent for all ALMEMO® sensors and cables, so that any pin configuration can be quickly and easily identified.
Order no. ZA9000AK
ALMEMO® 10-Fold MU Connector for ALMEMO® Plug-In Boards with 64-Pin Spring Contact Strip
+
03.14
01/2011 We reserve the right to make technical changes.
+
NOT suitable for sensors needing interface circuitry
(e.g. 26 V, AC voltage, mA, humidity sensors, rotating
vanes, frequency, pulse, rotational speed)
no sensor supply possible)
The current MU connector version, ZA5690MU, can only
be used in conjunction with the new ALMEMO® 5690
systems.
The old MU connector version, ZA5590MU, can of
course be used in conjunction with the old ALMEMO®
5590/5990 systems but is subject to certain restrictions
with the current 5690 systems (e.g. only 1 measuring
channel per input, no multi-point adjustment or
connector linearization).
Types:
ALMEMO® 10-fold connector (64-pin) with EEPROM sensor memory
for connecting 10 sensors; on request pre-programmed to your specifications
for Data acquisition systems ALMEMO® 5690 (not for ALMEMO® 5590 / 5990)
Order no. ZA5690MU
For Data acquisition systems ALMEMO 5590 / 5990
Order no. ZA5590MU
®
03
INPUT CONNECTORS
01/2011 We reserve the right to make technical changes.
ALMEMO® Connector Adapter Cable, Digital Input of Third Party Device to ALMEMO® Device
Type ZA 1000A KSW / ZAD 919A Kxx
Existing equipment incorporating a digital interface can, thanks to our flexible ALMEMO® system, continue being used.
For this purpose, we can offer you the following service :
1. We program a device type protocol for you, which matches the output interface of your device.
2. We fit the interface cable for your device with the matching ALMEMO® connector.
Description:
 Data acquisition from external devices with digital interface
and integration in the data acquisition with ALMEMO®
devices.
 The digital connector of the adapter cable provides an
electrically isolated serial interface and includes an interface
processor for protocol conversion.
 Value-adding to existing measuring technology at a very
interesting price-performance ratio.
Examples:
 Scales and weighing equipment
 Dial gauges and displacement transducers
 Multimeters
 Incremental displacement transducers
 Flue gas analysers
 Keypads
 Mains supply unit with RS232 data output
 Precision pressure sensors
 Equipment for work place related comfort index
measurements
Types:
For the purposes of programming the interface, please provide us with a detailed description of the output interface of the thirdparty device you want to have integrated, or a matching cable, or a connector including the pin configuration, plus the third-party
device itself for the purposes of testing and checking.
Interface programming for the device type protocol of the device to be integrated
Order no. ZA1000AKSW
®
ALMEMO connector adapter cable
Order no. ZAD919AK
www.ahlborn.com
03.15