Pride Mobility Celebrity XL deluxe Owner`s manual

CELEBRITY XL
DELUXE
SAFETY
GUIDELINES
WARNING! An authorised Pride Provider or qualified technician must perform the initial
setup of this scooter and must perform all of the procedures in this manual.
The symbols below are used throughout this owner's manual and on the scooter to identify warnings and important
information. It is very important for you to read them and understand them completely.
WARNING! Indicates a potentially hazardous condition/situation. Failure to follow
designated procedures can cause either personal injury, component damage or malfunction.
On the product, this icon is represented as a black symbol on a yellow triangle with a
black border.
MANDATORY! These actions should be performed as specified. Failure to perform
mandatory actions can cause personal injury and/or equipment damage. On the product,
this icon is represented as a white symbol on a blue dot.
PROHIBITED! These actions are prohibited. These actions should not be performed at any
time or in any circumstances. Performing a prohibited action can cause personal injury
and/or equipment damage. On the product, this icon is represented as a black symbol with
a red circle and a red slash.
Please fill out the following information for quick reference:
Pride Dealer:_______________________________________________________________________
Address:___________________________________________________________________________
Phone Number:__________________________
Purchase Date:__________________________ Serial Number:_____________________________
NOTE: This owner’s manual is compiled from the latest specifications and product information available at the time of publication. We reserve the right to make changes as they become necessary. Any
changes to our products may cause slight variations between the illustrations and explanations in this
manual and the product you have purchased. The latest/current version of this manual is available on
our website.
This product is manufactured by:
Pride Mobility Products Corporation
182 Susquehanna Avenue
Exeter, PA 18643-2694
USA
Copyright © 2008
Pride Mobility Products Pty. Ltd.
INFMANU3341/Rev B/May 2008
088 609 661
CONTENTS
I.
INTRODUCTION ......................................................................................................................... 4
II.
SAFETY ......................................................................................................................................... 5
III. YOUR SCOOTER ...................................................................................................................... 18
IV.
BATTERIES AND CHARGING ............................................................................................ 23
V.
OPERATION ............................................................................................................................... 29
VI. COMFORT ADJUSTMENTS................................................................................................ 31
VII. DISASSEMBLY AND ASSEMBLY ..................................................................................... 35
VIII. BASIC TROUBLESHOOTING ............................................................................................. 38
IX. CARE AND MAINTENANCE ................................................................................................ 40
X.
WARRANTY................................................................................................................................ 43
APPENDIX I - SPECIFICATIONS ............................................................................................... 44
Celebrity XL Deluxe
www.pridemobility.com
3
I.
INTRODUCTION
SAFETY
Welcome to Pride Mobility Products Australia Pty. Ltd. (Pride). The product you have purchased combines stateof-the-art components with safety, comfort, and styling in mind. We are confident the design features will provide
you with the conveniences you expect during your daily activities. Understanding how to safely operate and care
for this product should bring you years of trouble free operations and service.
Read and follow all instructions, warnings, and notes in this manual and all other accompanying literature before
attempting to operate this product for the first time. In addition, your safety depends upon you, as well as your
provider, caretaker, or healthcare professional in using good judgement.
If there is any information in this manual which you do not understand, or if you require additional assistance for
setup or operation, please contact your authorised Pride Provider. Failure to follow the instructions, warnings,
and notes in this manual and those located on your Pride product can result in personal injury or product
damage and will void Pride’s product warranty.
PURCHASER’S AGREEMENT
By accepting delivery of this product, you promise that you will not change, alter, or modify this product or remove
or render inoperable or unsafe any guards, shields, or other safety features of this product; fail, refuse, or neglect to
install any retrofit kits from time to time provided by Pride to enhance or preserve the safe use of this product.
SHIPPING AND DELIVERY
Before using your scooter, make sure your delivery is complete as some components may be individually packaged. If you do not receive a complete delivery, please contact your authorised Pride Provider immediately. Where
damage has occurred during transport, either to the packaging or content, please contact the delivery company
responsible.
INFORMATION EXCHANGE
We want to hear your questions, comments, and suggestions about this manual. We would also like to hear about
the safety and reliability of your new scooter, and about the service you received from your authorised Pride
Provider. Please notify us of any change of address, so we can keep you apprised of important information about
safety, new products, and new options that can increase your ability to use and enjoy your scooter. Please feel free
to contact us at the address below:
Pride Mobility Products Australia Pty. Ltd.
21 Healey Road
Dandenong, 3175
Victoria, Australia
NOTE: If you ever lose or misplace your product registration card or your copy of this manual, contact
us and we will be glad to send you a new one immediately.
4
www.pridemobility.com
Celebrity XL Deluxe
II.
SAFETY
PRODUCT SAFETY SYMBOLS
The symbols below are used on the scooter to identify warnings, mandatory actions, and prohibited actions. It is
very important for you to read and understand them completely.
Read and follow the information in the owner’s manual.
Use only AGM or Gel-Cell batteries to reduce the risk of leakage or explosive
conditions.
Maximum seating weight.
Pinch/Crush points created during assembly.
Corrosive chemicals contained in battery.
EMI-RFI- This product has been tested and passed at an immunity level of 20 V/m.
Unlocked and in freewheel mode.
Place unit on level ground and stand to one side when changing from drive mode
to freewheel mode or freewheel mode to drive mode.
Locked and in drive mode.
Celebrity XL Deluxe
www.pridemobility.com
5
II.
SAFETY
Do not allow unsupervised children to play near the scooter while the batteries
are charging.
Do not remove anti-tip wheels.
Do not use a cell phone, walkie/talkie, laptop, or other radio transmitter while
operating.
Avoid exposure to rain, snow, ice, salt, or standing water whenever possible.
Maintain and store in a clean and dry condition.
Removal of grounding prong can create electrical hazard. If necessary, properly
install an approved 3-pronged adapter to an electrical outlet having 2-pronged plug
access.
Do not connect an extension lead to the AC/DC converter or the battery charger.
Keep tools and other metal objects away from battery terminals. Contact with
tools can cause electrical shock.
Wear safety goggles.
Contains Lead.
6
www.pridemobility.com
Celebrity XL Deluxe
II.
SAFETY
Do not use batteries with different amp-hour (Ah) capacities. Do not mix old
and new batteries. Always replace both batteries at the same time.
Do not lift the mobility product while seated in it.
Do not place your scooter in freewheel mode while on a decline.
Do not place your scooter in freewheel mode while on a incline.
Explosive conditions exist!
Keep your hands away from the tyres when driving. Be aware that loose fitting
clothing can become caught in the drive tyres.
Disposal and recycling-contact your authorised Pride Provider for information on
proper disposal of your Pride product and its packaging.
Battery charger for indoor use only.
Celebrity XL Deluxe
www.pridemobility.com
7
II.
SAFETY
GENERAL
MANDATORY! Do not operate your new scooter for the first time without completely reading
and understanding this owner’s manual.
Your scooter is a state-of-the-art life-enhancement device designed to increase mobility. Pride provides an extensive variety of products to best fit the individual needs of the scooter user. Please be aware that the final selection
and purchasing decision regarding the type of scooter to be used is the responsibility of the scooter user who is
capable of making such a decision and his/her healthcare professional (i.e., medical doctor, physical therapist, etc.).
The contents of this manual are based on the expectation that a mobility device expert has properly fitted the
scooter to the user and has assisted the prescribing healthcare professional and/or the authorised Pride Provider in
the instruction process for the use of the product.
There are certain situations, including some medical conditions, where the scooter user will need to practice
operating the scooter in the presence of a trained attendant. A trained attendant can be defined as a family member
or care professional specially trained in assisting a scooter user in various daily living activities.
As you begin using your scooter during daily activities, you will probably encounter situations in which you will
need some practice. Simply take your time and you will soon be in full and confident control as you manoeuvre
through doorways, on and off lifts, up and down ramps, and over moderate terrain.
Below are some precautions, tips, and other safety considerations that will help you become accustomed to
operating the scooter safely.
MODIFICATIONS
Pride has designed and engineered your scooter to provide maximum mobility and utility. However, under no
circumstances should you modify, add, remove, or disable any feature, part, or function of your scooter.
WARNING! Do not modify your scooter in any way not authorized by Pride. Do not use
accessories if they have not been tested or approved for Pride products.
REMOVABLE PARTS
WARNING! Do not attempt to lift or move your scooter by any of it’s removable parts,
including the armrests, seat or shroud.
PRE-RIDE SAFETY CHECK
Get to know the feel of your scooter and its capabilities. Pride recommends that you perform a safety check before
each use to make sure your scooter operates smoothly and safely.
8
www.pridemobility.com
Celebrity XL Deluxe
II.
SAFETY
Perform the following inspections prior to using your scooter:
! Check for proper tyre inflation. Maintain but do not exceed the psi/bar/kPa air pressure rating indicated on
each tyre if equiped with pneumatic tires.
! Check all electrical connections. Make sure they are tight and not corroded.
! Check all harness connections. Make sure they are secured properly.
! Check the brakes.
! Check battery charge.
If you discover a problem, contact your authorised Pride Provider for assistance.
TYRE INFLATION
If your scooter is equipped with pneumatic tyres, you should check or have the air pressure checked at least once a
week. Proper inflation pressures will prolong the life of your tyres and help ensure the smooth operation of your scooter.
WARNING! It is critically important that the psi/bar/kPa air pressure indicated on each tyre
be maintained in pneumatic tyres at all times. Do not underinflate or overinflate your tyres.
Low pressure may result in loss of control, and overinflated tyres may burst. Failure to
maintain the psi/bar/kPa air pressure rating indicated on pneumatic tyres at all times may
result in tyre and/or wheel failure.
WARNING! Inflate your scooter tyres from a regulated air source with an available pressure
gauge. Inflating your tyres from an unregulated air source could overinflate them, resulting
in a burst tyre.
WARNING! When changing a tyre, remove only the centre lug nut, then remove the wheel.
If any further disassembly is required, deflate the tyre completely or it may explode.
NOTE: If the tyres on your scooter list the psi rating only, use the following conversion formulas to
find the bar or kPa rating: bar=psi x 0.06895, kPa= psi x 6.89476.
WEIGHT LIMITATIONS
Your scooter is rated for a maximum weight capacity. Refer to the specifications table for information.
MANDATORY! Stay within the specified weight capacity for your scooter. Exceeding the
weight capacity voids your warranty. Pride will not be held responsible for injuries and/or
property damage resulting from failure to observe weight limitations.
WARNING! Do not carry passengers on your scooter. Carrying passengers on your scooter
may affect the center of gravity, resulting in a tip or a fall.
INCLINE INFORMATION
More and more buildings have ramps with specified degrees of inclination, designed for easy and safe access. Some
ramps may have turning switchbacks (180-degree turns) that require you to have good cornering skills on your scooter.
! Proceed with extreme caution as you approach the downgrade of a ramp or other incline.
! Take wide swings with your scooter around any tight corners. If you do that, the scooter’s rear wheels will
follow a wide arc, not cut the corner short and not bump into or get hung up on any railing corners.
! When driving down a ramp, keep the scooter’s speed adjustment set to the slowest speed setting to ensure a
safely controlled descent.
! Avoid sudden stops and starts.
Celebrity XL Deluxe
www.pridemobility.com
9
II.
SAFETY
When climbing an incline, try to keep your scooter moving. If you must stop, start up again slowly and then
accelerate cautiously. When driving down an incline, do so by setting the speed adjustment dial to the slowest
setting and driving in the forward direction only. If your scooter starts to move down the incline faster than you
anticipated or desired, allow it to come to a complete stop by releasing the throttle control lever. Then push the
throttle control lever forward slightly to ensure a safely controlled descent.
WARNING! When on any sort of an incline or decline, never place the scooter in
freewheel mode especially while seated on it or standing next to it.
WARNING! When climbing an incline, do not zigzag or drive at an angle up the
face of the incline. Drive your scooter straight up the incline. This greatly reduces
the possibility of a tip or a fall. Always exercise extreme caution when negotiating
an incline.
WARNING! Do not drive your scooter across the side of an incline or diagonally up
or down an incline; do not stop, if possible, while driving up or down an incline.
WARNING! You should not travel up or down a potentially hazardous incline (i.e.,
areas covered with snow, ice, cut grass or wet leaves).
WARNING! Even though your scooter is capable of climbing slopes greater than
those illustrated in figure 1, do not, under any circumstances, exceed the incline
guidelines or any other specifications presented in this manual. Doing so could
cause instability in your scooter.
Handicap public access ramps are not subject to government regulation in all countries and therefore do not
necessarily share the same standard percent of slope. Other inclines may be natural or, if man-made, not designed
specifically for scooters. Figure 1 illustrates your scooter’s stability and its ability to climb grades under various
weight loads and under controlled testing conditions.
These tests were conducted with the scooter’s seat in the highest position and adjusted rearward on the seat base
to its farthest rearward position. Use this information as a guideline. Your scooter’s ability to travel up inclines is
affected by your weight, your scooter’s speed, your angle of approach to the incline and your scooter setup.
181 kg
15.8% (9˚)
Figure 1. Maximum Recommended Incline Angle
WARNING! Any attempt to climb or descend a slope steeper than what is shown in figure
1 may put your scooter in an unstable position and cause it to tip, resulting in personal
injury.
WARNING! Never carry an oxygen tank weighing more than 6 kg. Never fill the front or
rear basket with contents exceeding 6 kg.
10
www.pridemobility.com
Celebrity XL Deluxe
II.
SAFETY
When you approach an incline, it is best to lean forward. See figures 2 and 2A. This shifts the centre of gravity of
you and your scooter toward the front of the scooter for improved stability.
NOTE: When negotiating ramps, if the throttle control lever is released while moving forward, the
powered scooter may "rollback" approximately 30.5 cm before the brake engages. If the throttle control lever is released while moving in reverse, the powered scooter may "rollback" approximately one
metre before the brake engages.
Figure 2. Normal Driving Position
Figure 2A. Increased Stability Driving Position
CORNERING INFORMATION
Excessively high cornering speeds can create the possibility of tipping. Factors which affect the possibility of
tipping include, but are not limited to, cornering speed, steering angle (how sharply you are turning), uneven road
surfaces, inclined road surfaces, riding from an area of low traction to an area of high traction (such as passing from
a grassy area to a paved area – especially at high speed while turning) and abrupt directional changes. High
cornering speeds are not recommended. If you feel that you may tip over in a corner, reduce your speed and
steering angle (i.e., lessen the sharpness of the turn) to prevent your scooter from tipping.
WARNING! When cornering sharply, reduce your speed and maintain a stable center of
gravity. When using your scooter at higher speeds, do not corner sharply. This greatly
reduces the possibility of a tip or fall. Always exercise common sense when cornering.
BRAKING INFORMATION
Your scooter is equipped with these powerful brake systems:
! Regenerative: Uses electricity to rapidly slow the vehicle when the throttle control lever returns to the centre/
stop position.
! Disc Park Brake: Activates mechanically after regenerative braking slows the vehicle to near stop or when
power is removed from the system for any reason.
! Handbrake: Gives you additional stopping power when you squeeze it. See III. “Your Scooter.”
Celebrity XL Deluxe
www.pridemobility.com
11
II.
SAFETY
OUTDOOR DRIVING SURFACES
Your scooter is designed to provide optimum stability under normal driving conditions—dry, level surfaces composed of concrete or tarmac. However, Pride recognises that there will be times when you will encounter other
surface types. For this reason, your scooter is designed to perform admirably on packed soil, grass, and gravel.
Feel free to use your scooter safely on lawns and in park areas.
! Reduce your scooter’s speed when driving on uneven terrain and/or soft surfaces.
! Avoid tall grass that can become tangled in the running gear.
! Avoid loosely packed gravel and sand.
! If you feel unsure about a driving surface, avoid that surface.
PUBLIC STREETS AND ROADWAYS
WARNING! Exercise extreme caution when operating the scooter on footpaths, pavements,
bridleways, pedestrian areas, and, roads. Obey all local pedestrian traffic rules.
STATIONARY OBSTACLES (STEPS, KERBS, ETC.)
WARNING! Do not drive near raised surfaces, unprotected ledges, and/or drop-offs (kerbs,
porches, stairs, etc.).
WARNING! Do not attempt to have your scooter climb or descend an obstacle that is
inordinately high.
WARNING! Do not attempt to have your scooter proceed rearward down any step, kerb, or
other obstacle. This may cause the scooter to tip.
WARNING! Be sure your scooter is traveling perpendicular to any kerb you may be required
to ascend or descend. See figures 3 and 3A.
WARNING! Do not attempt to negotiate a kerb that has a height greater than 5 cm (2 in.).
KERB
KERB
Figure 3. Correct Kerb Approach
12
Figure 4. Incorrect Kerb Approach
www.pridemobility.com
Celebrity XL Deluxe
II.
SAFETY
INCLEMENT WEATHER PRECAUTIONS
Exposure of your scooter to inclement weather conditions should be avoided whenever possible. If suddenly caught
up in rain, snow, severe cold or heat while operating your scooter, proceed to shelter at the earliest opportunity.
Thoroughly dry your scooter before storing, charging or operating your scooter.
PROHIBITED! Operating in rain, snow, salt, mist/spray conditions and on icy/slippery surfaces
may have an adverse affect on the electrical system. Maintain and store your scooter in a
dry and clean condition.
WARNING! Prolonged exposure to hot or cold conditions may affect the temperature of
upholstered and non-upholstered items on the scooter, possibly resulting in skin irritation.
Exercise caution when using your scooter in extremely hot or cold conditions or when
exposing your scooter to direct sunlight for prolonged periods of time.
FREEWHEEL MODE
Your scooter is equipped with a manual freewheel lever that, when engaged, allows the scooter to be pushed. For
more information about how to place your scooter into and out of freewheel mode, see III. “Your Scooter.”
WARNING! When your scooter is in freewheel mode, the braking system is disengaged.
! Disengage the drive motors only on a level surface.
! Ensure the key is removed from the key switch.
! Stand to the side of the scooter to engage or disengage freewheel mode. Never sit on
a scooter to do this.
! After you have finished pushing your scooter, always return it to the drive mode to lock
the brakes.
An added feature built into the scooter is “push-too-fast” protection which safeguards the scooter against gaining
excessive speed while in freewheel mode.
“Push-too-fast” operates differently depending on which of two conditions exists:
! If the key is switched “off” while in freewheel mode, the scooter’s controller activates regenerative braking
when the scooter is pushed faster than a maximum threshold which has been preprogrammed. In this case, the
controller is acting as a speed governor.
! If the key is switched “on” while in freewheel mode, you will encounter considerable resistance at any speed.
This prevents the scooter from gaining unwanted momentum should the manual freewheel lever inadvertently
be released while driving the scooter.
STAIRS AND ESCALATORS
Scooters are not designed to travel up or down stairs or escalators. Always use a lift.
WARNING! Do not use your scooter to negotiate steps or escalators.
DOORS
! Determine if the door opens toward or away from you.
! Use your hand to turn the knob or push the handle or push-bar.
! Drive your scooter gently and slowly forward to push the door open. Or drive your scooter gently and slowly
rearwards to pull the door open.
Celebrity XL Deluxe
www.pridemobility.com
13
II.
SAFETY
LIFTS
Modern lifts have a door edge safety mechanism that, when pushed, reopens the door(s).
! If you are in the doorway of a lift when the door(s) begin to close, push on the rubber door edge or allow the
rubber door edge to contact the scooter and the door will reopen.
! Use care that handbags, packages, or scooter accessories do not become caught in lift doors.
NOTE: If your scooter’s turning radius is greater than 1500 mm (60 in.), it may be difficult to manoeuvre in lifts and building entrances. Use caution when attempting to turn or manoeuvre your scooter in
small spaces and avoid areas that might pose a problem.
LIFT/ELEVATION PRODUCTS
If you will be traveling with your scooter, you may find it necessary to use a lift/elevation product to aid in transportation. Pride recommends that you closely review the instructions, specifications, and safety information set forth
by the manufacturer of the lift/elevation product before using that product.
WARNING! Never sit on your scooter when it is being used in connection with
any type of lift/elevation product. Your scooter was not designed with such use
in mind and any damage or injury incurred from such use is not the responsibility
of Pride.
BATTERIES
In addition to following the warnings below, be sure to comply with all other battery handling information.
MANDATORY! Battery posts, terminals and related accessories contain lead and
lead compounds. Wear goggles and gloves when handling batteries and wash
hands after handling.
WARNING! Scooter batteries are heavy. See specifications table. If you are unable
to lift that much weight, be sure to get help. Use proper lifting techniques and
avoid lifting beyond your capacity.
WARNING! Always protect the batteries from freezing and never charge a frozen
battery.
WARNING! Connect the battery harnesses in the proper manner. RED (+) cables
must be connected to positive (+) battery terminals/posts. BLACK (-) cables must
be connected to negative (-) batter y terminals/posts. REPLACE cables
immediately if damaged. Protective caps must be installed over all battery
terminals.
NOTE: If you encounter a damaged or cracked battery, immediately enclose it in a plastic bag and
contact your local waste disposal agency or authorized Pride Provider for instructions on disposal and
battery recycling which is our recommended course of action.
PREVENTING UNINTENDED MOVEMENT
WARNING! If you anticipate being seated in a stationary position for an extended period
of time, turn off the power. This will prevent unexpected motion from inadvertent throttle
control lever contact.
14
www.pridemobility.com
Celebrity XL Deluxe
II.
SAFETY
MOTOR VEHICLE TRANSPORT
Pride recommends that you do not remain seated in your scooter while traveling in a motor vehicle. The scooter
should be stowed in the trunk of a car or in the back of a truck or van with batteries removed and properly secured.
In addition, all removable scooter parts, including the armrests, seat, and shroud should be removed and/or properly secured during motor vehicle transport.
WARNING! Although your scooter may be equipped with a positioning belt, this belt is not
designed to provide proper restraint during motor vehicle transport. Anyone traveling in a
motor vehicle should be properly secured in the motor vehicle seat with safety belts fastened
securely.
WARNING! Do not sit on your scooter while it is in a moving vehicle.
WARNING! Always be sure your scooter and its batteries are properly secured when it is
being transported. Batteries should be secured in an upright position and protective caps
should be installed on the battery terminals. Batteries should not be transported with any
flammable or combustible items.
GETTING ONTO AND OFF YOUR SCOOTER
Getting onto and off of your scooter requires a good sense of balance. Please observe the following safety tips
when getting onto and off your scooter:
! Remove the key from the key switch.
! Ensure that your scooter is not in freewheel mode. See III. “Your Scooter.”
! Make certain that the seat is fixed into place.
! Pivot the armrests up to make getting onto and off of the scooter easier.
WARNING! Position yourself as far back as possible in the scooter seat to prevent the
scooter from tipping.
WARNING! Avoid putting all of your weight on the scooter armrests and do not use the
armrests for weight bearing purposes, such as transfers. Such use may cause the scooter
to tip, resulting in a fall from the scooter.
WARNING! Avoid putting all of your weight on the floorboard. Such use may cause the
scooter to tip.
REACHING AND BENDING
Avoid reaching or bending while driving your scooter. Bending forward creates the risk of accidental throttle
control lever contact. Bending to the side while seated creates the risk of tipping. It is important to maintain a stable
centre of gravity and keep the scooter from tipping. Pride recommends that the scooter user determine his/her
personal limitations and practice bending and reaching in the presence of a qualified attendant.
WARNING! Do not bend, lean or reach for objects if you have to pick them up from the
scooter deck or from either side of the scooter. Movements such as these may change
your centre of gravity and the weight distribution of the scooter and cause your scooter
to tip.
PROHIBITED! Keep your hands away from the tyres when driving. Be aware that loose
fitting clothing can become caught in drive tyres.
Celebrity XL Deluxe
www.pridemobility.com
15
II.
SAFETY
POSITIONING BELTS
Your authorised Pride Provider, therapist(s) and other healthcare professionals are responsible for determining
your requirement for a positioning belt in order to operate your scooter safely.
WARNING! If you require a positioning belt to safely operate your scooter, make sure it is
fastened securely in order to reduce the possiblity of a fall from the scooter.
PRESCRIPTION DRUGS/PHYSICAL LIMITATIONS
The scooter user must exercise care and common sense when operating his/her scooter. This includes awareness of
safety issues when taking prescribed or over-the-counter drugs or when the user has specific physical limitations.
WARNING! Consult your physician if you are taking prescribed or over-the-counter
medication or if you have certain physical limitations. Some medications and limitations
may impair your ability to operate your scooter in a safe manner.
ALCOHOL/SMOKING
The scooter user must exercise care and common sense when operating his/her scooter. This includes awareness
of safety issues while under the influence of alcohol or while smoking.
WARNING! Do not operate your scooter while you are under the influence of alcohol, as
this may impair your ability to operate the scooter in a safe manner.
WARNING! Pride strongly recommends that you do not smoke cigarettes while seated on
your scooter, although the scooter seat has passed the necessary testing requirements
for cigarette smoking. You must adhere to the following safety guidelines if you decide to
smoke cigarettes while seated on your scooter.
! Do not leave lit cigarettes unattended.
! Keep ashtrays a safe distance from the seat cushions.
! Always make sure cigarettes are completely extinguished before disposal.
16
www.pridemobility.com
Celebrity XL Deluxe
II.
SAFETY
ELECTROMAGNETIC AND RADIO FREQUENCY INTERFERENCE (EMI/RFI)
WARNING! Laboratory tests have shown that electromagnetic and radio frequency waves
can have an adverse affect on the performance of electrically-powered mobility vehicles.
Electromagnetic and Radio Frequency Interference can come from sources such as cellular phones, mobile twoway radios (such as walkie-talkies), radio stations, TV stations, amateur radio (HAM) transmitters, wireless
computer links, microwave signals, paging transmitters, and medium-range mobile transceivers used by emergency
vehicles. In some cases, these waves can cause unintended movement or damage to the control system. Every
electrically-powered mobility vehicle has an immunity (or resistance) to EMI. The higher the immunity level, the
greater the protection against EMI. This product has been tested and has passed at an immunity level of 20 V/M.
WARNING! Be aware that cell phones, two-way radios, laptops, and other types of radio
transmitters may cause unintended movement of your electrically-powered mobility vehicle
due to EMI. Exercise caution when using any of these items while operating your mobility
vehicle and avoid coming into close proximity of radio and TV stations.
WARNING! The addition of accessories or components to the electrically-powered mobility
vehicle can increase the susceptibility of the vehicle to EMI. Do not modify your scooter in
any way not authorised by Pride.
WARNING! The electrically-powered mobility vehicle itself can disturb the performance
of other electrical devices located nearby, such as alarm systems.
NOTE: If unintended motion or brake release occurs, turn the scooter off as soon as it is safe to do so.
Contact your authorised Pride Provider to report the incident.
Celebrity XL Deluxe
www.pridemobility.com
17
III. YOUR
SCOOTER
TILLER CONSOLE
The tiller console houses all of the controls needed to drive your scooter, including the speed adjustment dial, throttle
control lever, battery condition meter, lights switch, hazard lights switch, and horn buttons. See figure 5.
PROHIBITED! Do not expose the tiller console to moisture. In the event that the tiller
console does become exposed to moisture, do not attempt to operate your scooter until
the tiller console has dried thoroughly.
BATTERY CONDITION METER
HANDBRAKE LEVER
SPEED
ADJUSTMENT
DIAL
KEY SWITCH
THROTTLE
CONTROL
LEVER
THROTTLE
CONTROL
LEVER
LEFT TURN INDICATOR
RIGHT TURN INDICATOR
HORN BUTTON
HORN BUTTON
HI-LOW SWITCH
HAZARD LIGHTS SWITCH
LIGHTS SWITCH
Figure 5. Tiller Console
Horn Buttons
These buttons activate a warning horn. Your scooter must be powered up for the horn to be operational. Do not
hesitate to use the warning horn when doing so may prevent accident or injury.
Key Switch
! Insert the key into the key switch and turn it clockwise to power up (turn on) your scooter.
! Turn the key anticlockwise to power down (turn off) your scooter.
WARNING! If the key is moved to the “off” position while your scooter is in motion, the
electronic brakes will engage and your scooter will come to an abrupt stop!
Battery Condition Meter
When the key is fully inserted and turned clockwise to power up your scooter, this meter indicates the approximate
battery voltage strength. For further information on battery charging, see IV. “Batteries and Charging.”
Turn Indicator Buttons
Use these buttons to turn on the left and right turn indicator (amber) lights. See figure 5.
! Push the left button to activate the left turn indicator light.
! Push the right button to activate the right turn indicator light.
! The indicators are timed to shut off automatically.
18
www.pridemobility.com
Celebrity XL Deluxe
III. YOUR
SCOOTER
Hi-Low Switch
! Toggle the switch forward (HI) and your scooter’s maximum speed is 15 km/h (8 mph).
! Toggle the switch rearward (LOW) and your scooter’s maximum speed is 7.5 km/h (4 mph).
Lights Switch
This switch controls your scooter’s lights.
! Toggle the switch forward to turn on your scooter’s front top light and running lights.
! Toggle the switch to the middle to turn off the scooter’s lights.
! Toggle the switch rearward to turn on all the scooter’s lights (upper and lower front and running lights).
WARNING! Scooter users are required to use their lights when visibility is restricted—day or
night.
Hazard Lights Switch
This switch activates the 4-way flashers on your scooter.
! Toggle the hazard lights switch forward to turn on the flashers.
! Toggle the hazard lights switch rearward to turn off the flashers.
Throttle Control Lever
This lever allows you to control the forward speed and the reverse speed of your scooter up to the maximum speed
you preset with the speed adjustment dial.
To Move Forward use either of the following:
! Use your left thumb to push the left side of the throttle control lever.
! Use your right hand fingers to pull back on the right side of the throttle control lever.
To Move Rearward use either of the following:
! Use your right thumb to push the right side of the throttle control lever.
! Use your left hand fingers to pull back on the left side of the throttle control lever.
Release the throttle control lever and allow your scooter to come to a complete stop before engaging the other side
of the lever. When the throttle control lever is completely released, it automatically returns to the centre “stop”
position and engages your scooter’s brakes.
Handbrake Lever
This lever provides you with additional stopping power. Release the throttle control lever and gently squeeze the
handbrake lever to come to a stop.
NOTE: If you do not release the throttle control lever before using the handbrake, your scooter may not
come to a complete stop.
Speed Adjustment Dial
This dial allows you to preselect and limit your scooter’s top speed.
! The image of the tortoise represents the slowest speed setting.
! The image of the hare represents the fastest speed setting.
Celebrity XL Deluxe
www.pridemobility.com
19
III. YOUR
SCOOTER
Off-board Charger Port
The off-board charger power lead plugs into this port when charging the batteries. See figure 6.
Tiller Console Fuses
These fuses help protect your scooter’s front lighting, turn indicators, and key switch console systems from receiving
an overload of electrical current. The fuses used in your scooter are the same type used in automobiles. See figure 7.
See IX. “Care and Maintenance” for fuse replacement.
SPARE
RUNNING LIGHTS
LOWER HEADLIGHT
LEFT TURN INDICATOR
RIGHT TURN INDICATOR
Figure 6. Off-board Charger Port
Figure 7. Tiller Console Fuses
REAR SECTION
The batteries, the main circuit breaker (reset button), the manual freewheel lever, the anti-tip wheels, and the
motor/transaxle assembly are located on the rear section of your scooter. See figure 8.
Batteries
The batteries store the electrical energy
that powers your scooter. See IV. “Batteries and Charging ” for information on
how to charge your scooter batteries.
BATTERIES
MANUAL
FREEWHEEL
LEVER
Motor/Transaxle Assembly
The motor/transaxle assembly is an electromechanical unit that converts electrical energy from your scooter’s batteries
into the controlled mechanical energy that
drives the scooter’s wheels.
MOTOR/TRANSAXLE ASSEMBLY
Anti-tip Wheels
The anti-tip wheels are an integral and
important safety feature designed to help
prevent your scooter from tipping rear- Figure 8. Rear Section
wards on an incline. They are bolted to
the frame at the rearmost part of your scooter. See figure 8.
ANTI-TIP WHEELS
PROHIBITED! Do not remove the anti-tip wheels or modify your scooter in any way that is
not authorised by Pride.
20
www.pridemobility.com
Celebrity XL Deluxe
III. YOUR
SCOOTER
Manual Freewheel Lever
Whenever you need or want to push your scooter for short distances, you can put it in freewheel mode.
1. Remove the key from the key switch.
2. Push forward on the manual freewheel lever to disable the drive system and the brake system. You may now
push your scooter.
3. Pull back on the manual freewheel lever to reengage the drive and the brake systems and take your scooter out
of freewheel mode.
WARNING! When your scooter is in freewheel mode, the braking system is disengaged.
! Disengage the drive motors only on a level surface.
! Ensure the key is removed from the key switch.
! Stand to the side of the scooter to engage or disengage freewheel mode. Never sit on
a scooter to do this.
! After you have finished pushing your scooter, always return it to the drive mode to lock
the brakes.
NOTE: If the scooter is placed in freewheel mode (manual freewheel lever forward) while the key is in
the “on” position, the scooter will not run until the manual freewheel lever is pushed rearward and the
key is turned to the “off” position, then back to the “on” position.
Safety Flag Bracket
An accessory bracket for installing an optional safety
flag is mounted near each anti-tip wheel. To install the
flag, the supplied “L” shaped hex key is needed. See
figure 8A.
HEX KEY
CAP
Installation:
1. Remove the cap from the top of the bracket.
2. Loosen the setscrew with the supplied “L”
shaped hex key.
3. Insert the flag pole into the opening.
4. Tighten the setscrew to complete installation.
SETSCREW
Figure 8A. Safety Flag Bracket
Celebrity XL Deluxe
www.pridemobility.com
21
III. YOUR
Main Circuit Breaker (Reset Button)
When the voltage in the batteries becomes low or your
scooter is heavily strained because of excessive loads,
the main circuit breaker may trip to protect the motor
and electronics from damage. When the breaker trips,
the entire electrical system shuts down. See figure 9.
! The reset button pops out when the breaker trips.
! Allow a minute or so for the electronics to “rest.”
! Push in the reset button to reset the breaker.
! If the breaker trips frequently, you may need to
charge the batteries more often or have your
authorised Pride Provider perform a load test on
the batteries.
SCOOTER
MAIN CIRCUIT BREAKER (RESET BUTTON)
Figure 9. Main Circuit Breaker (Reset Button)
SECUREMENT POINTS
Steel loops welded to the anti-tip wheel brackets and/or front frame components of your scooter provide securement points. See figures 10 and 10A. These should only be used with an unoccupied scooter and secured by an
approved securement system in accordance with the manufacturer’s instructions. Pride makes no representation of
suitability for use with specific securement systems nor can we anticipate the various situations that might arise in
use of public transportation systems. For detailed instructions on the use of securement systems, refer to the
applicable municipal transit authority and/or manufacturer of the system used.
WARNING! DO NOT leave the scooter in freewheel mode when securing it for transport.
WARNING! DO NOT use your scooter as a seat in a moving vehicle.
SECUREMENT POINTS
SECUREMENT POINTS
Figure 10. Rear Securement Points
22
Figure 10A. Front Securement Points
www.pridemobility.com
Celebrity XL Deluxe
I V. B AT T E R I E S A N D C H A R G I N G
Your scooter requires two long-lasting, 12-volt, deep-cycle batteries that are sealed and maintenance free. They
are recharged by an off-board charging system.
! Charge your scooter’s batteries prior to using it for the first time.
! Keep the batteries fully charged to keep your scooter running smoothly.
READING YOUR BATTERY VOLTAGE
The battery condition meter on the tiller console indicates the approximate strength of your batteries using a colour code. From right to left,
green indicates fully charged batteries, yellow a draining charge, and red
indicates that an immediate recharge is necessary. See figure 11. To ensure the highest accuracy, the battery condition meter should be checked
while operating your scooter at full speed on a dry, level surface.
CHARGING YOUR BATTERIES
Figure 11. Battery Condition Meter
PROHIBITED! Removal of grounding prong can create electrical hazard. If necessary,
properly install an approved 3-pronged adapter to an electrical outlet having 2-pronged
plug access.
PROHIBITED! Never use an extension lead to plug in your battery charger. Plug the charger
directly into a properly wired standard electrical outlet.
PROHIBITED! Do not allow unsupervised children to play near the scooter while the batteries
are charging. Pride recommends that you do not charge the batteries while the scooter is
occupied.
MANDATORY! Read the battery charging instructions in this manual and in the manual
supplied with the battery charger before charging the batteries.
WARNING! Explosive gases may be generated while charging the batteries. Keep the scooter
and battery charger away from sources of ignition such as flames or sparks and provide
adequate ventilation when charging the batteries.
WARNING! You must recharge your scooter’s batteries with the supplied off-board charger.
Do not use an automotive-type battery charger.
WARNING! Inspect the battery charger, wiring and connectors for damage before each
use. Contact your authorised Pride Provider if damage is found.
WARNING! Do not attempt to open the battery charger case. If the battery charger does
not appear to be working correctly, contact your authorised Pride Provider.
WARNING! If the battery charger is equipped with cooling slots, then do not attempt to
insert objects through these slots.
WARNING! If your battery charger has not been tested and approved for outdoor use, then
do not expose it to adverse or extreme weather conditions. If the battery charger is exposed
to adverse or extreme weather conditions, then it must be allowed to adjust to the difference
in environmental conditions before use indoors. Refer to the manual supplied with the
battery charger for more information.
Celebrity XL Deluxe
www.pridemobility.com
23
I V. B AT T E R I E S A N D C H A R G I N G
The off-board charger supplied with your scooter is equipped with a 115/230 voltage switch. Confirm that this
switch is in the proper position for your locality. If you are not sure what the voltage is in your country, contact your
local electricity provider before inserting the charger power lead plug into your electrical outlet. If the setting is
incorrect, the charger will not function properly. Slide the voltage switch to the appropriate position. See figure 12.
The LED lights on the charger indicate different charger conditions at various times: charger power on, charging in
progress, charging complete. Refer to the label on the charger for a complete explanation of these indicators.
OFF
ON
PLUGS INTO THE OFF-BOARD
CHARGER PORT
PLUGS INTO ELECTRICAL
OUTLET
VOLTAGE SWITCH
I
O
Figure 12. Charger On/Off and Voltage Switches
Figure 12A. Off-board Charger
Follow these easy steps to charge your batteries safely:
1. Position your scooter close to a standard electrical outlet.
2. Remove the key from the key switch.
3. Make certain that the manual freewheel lever is in the drive position.
4. Plug the 3-pin charger power lead into the off-board charger port. See figure 12A.
5. Make sure the charger’s on/off switch is in the OFF position.
6. Extend the charger power lead and plug it into the electrical outlet.
7. Turn the charger on. See figure 12. We recommend that you charge the batteries for 8 to 14 hours.
8. When the batteries are fully charged, turn the charger off and unplug the charger power lead from the electrical
outlet and then from the off-board charger port.
NOTE: There is a charger inhibit function on your scooter. The scooter will not run and the battery
condition meter will not operate while the batteries are charging.
24
www.pridemobility.com
Celebrity XL Deluxe
I V. B AT T E R I E S A N D C H A R G I N G
FREQUENTLY ASKED QUESTIONS
How does the charger work?
When your scooter’s battery voltage is low, the charger works harder, sending more electrical current to the
batteries to bring up their charge. As the batteries approach a full charge, the charger sends less and less electrical
current. When the batteries are fully charged, the current sent from the charger is at nearly zero amperage. Therefore, when the charger is plugged in, it maintains the charge on your scooter’s batteries, but does not overcharge
them. We do not recommend that you charge your scooter’s batteries for more than 24 consecutive hours.
Can I use a different charger?
Chargers are selected precisely for particular applications and are especially matched to the type, size and chemical formulation of specific batteries. For the safest and most efficient charging of your scooter’s batteries, we
recommend use of the charger supplied as original equipment with your Pride product only. Any charging method
resulting in batteries being charged individually is especially prohibited.
What if my scooter’s batteries won’t charge?
! Ensure the red (+) and black (-) battery cables are connected properly to the battery terminals.
! Ensure both battery harnesses that extend from the batteries are plugged into their mating harness leading to
the charger.
! Ensure both ends of the charger power lead are inserted fully.
How often must I charge the batteries?
Two major factors must be considered when deciding how often to charge your scooter’s batteries:
! All day scooter use on a daily basis.
! Infrequent or sporadic scooter use.
With these considerations in mind, you can determine how often and for how long you should charge your scooter’s
batteries. We designed the off-board charger so that it will not overcharge your scooter’s batteries. However, you
may encounter some problems if you do not charge your batteries often enough and if you do not charge them on
a regular basis. Following the guidelines below will provide safe and reliable battery operation and charging.
! If you use your scooter daily, charge its batteries as soon as you finish using it for the day. Your scooter will be
ready each morning. We recommend that you charge your scooter’s batteries for 8 to 14 hours after daily use.
! If you use your scooter once a week or less, charge its batteries at least once a week for 12 to 14 hours at a time.
! Keep your scooter’s batteries fully charged.
! Avoid deeply discharging your scooter’s batteries.
How can I ensure maximum battery life?
Fully charged deep-cycle batteries provide reliable performance and extended battery life. Keep your scooter’s
batteries fully charged whenever possible. Protect your scooter and batteries from extreme heat or cold. Batteries
that are regularly and deeply discharged, infrequently charged, stored in extreme temperatures or stored without a full
charge may be permanently damaged, causing unreliable performance and limited service life.
Celebrity XL Deluxe
www.pridemobility.com
25
I V. B AT T E R I E S A N D C H A R G I N G
!
!
!
!
!
!
Always fully charge your scooter’s batteries prior to daily use.
Maintain but do not exceed the psi/bar/kPa air pressure rating indicated on pneumatic tyres.
Plan your route ahead to avoid as many hills, cracked, broken or soft surfaces as possible.
Limit your baggage weight to essential items.
Try to maintain an even speed while your scooter is in motion.
Avoid stop-and-go driving.
What type and size of battery should I use?
We recommend deep-cycle batteries that are sealed and maintenance free. Both AGM and Gel-Cell are deepcycle batteries that are similar in performance. Do not use wet-cell batteries, which have removable caps.
WARNING! Corrosive chemicals are contained in batteries. Use only AGM or Gel-Cell
batteries to reduce the risk of leakage or explosive conditions.
NOTE: Sealed batteries are not serviceable. Do not remove the caps.
How do I change a battery in my scooter?
MANDATORY! Battery posts, terminals, and related accessories contain lead and lead
compounds. Wear goggles and gloves when handling batteries and wash hands after handling.
WARNING! Always use two batteries of the exact same type, chemistry, and amphour (Ah) capacity. Refer to the specifications table in this manual and in the
manual supplied with the battery charger for recommended type and capacities.
WARNING! Contact your authorized Pride Provider if you have any questions
regarding the batteries in your scooter.
WARNING! Do not replace the batteries while the scooter is occupied.
WARNING! Do not mix old and new batteries. Always replace both batteries at the
same time.
WARNING! The batteries on your scooter should only be serviced or replaced by
an authorized Pride Provider or a qualified technician.
1.
2.
3.
4.
5.
6.
7.
8.
9.
Remove the seat and rear shroud. See VII. “Disassembly and Assembly.”
Disconnect the battery tie-down strap.
Disconnect the battery harnesses by pulling them straight up. See figure 13.
Disconnect the battery cables from the battery terminals.
Remove the old batteries.
Place a new battery in each battery well. Face the battery terminals toward the seat post.
Connect the red battery cable to the positive (+) battery terminal. See figure 13A.
Connect the black battery cable to the negative (-) battery terminal.
Ensure the battery terminals are covered with the tiller boots.
NOTE: See figure 13B for correct hardware placement for battery terminal connections.
26
www.pridemobility.com
Celebrity XL Deluxe
I V. B AT T E R I E S A N D C H A R G I N G
10. Reconnect the battery harnesses.
11. Reconnect the battery tie-down strap,
making sure the strap is positioned over
the frame release lever to ensure proper
securement. See figure 13C.
12. Reinstall the rear shroud and seat.
If you encounter a damaged or cracked
battery, immediately enclose it in a plastic bag and contact your local waste disposal agency or authorized Pride Provider
for instructions on disposal and battery recycling which is our recommended course
of action.
BATTERY
TERMINALS
UNDER
BOOTS
BATTERY
HARNESSES
Figure 13. Battery Harnesses and Battery Cables
+
BATTERY
Why do my new batteries seem weak?
Deep-cycle batteries employ a different chemical technology than that used in car batteries,
nickel-cadmium batteries (nicads) and other
common battery types. Deep-cycle batteries
are specifically designed to provide power,
drain down their charge and then accept a relatively quick recharge.
We work closely with our battery manufacturer to provide batteries that best suit your
scooter’s specific electrical demands. Fresh
batteries are shipped fully charged to our customers. During shipping, the batteries may encounter temperature extremes that can influence their initial performance. Heat diminishes
the charge on the battery; cold slows the available power and extends the time needed to
recharge the battery.
+
BATTERY
Figure 13A. Battery Cable
Orientation
Figure 13B. Cable To Terminal
Connection
BATTERY TIE-DOWN STRAP
Figure 13C. Battery Tie-Down Strap
Celebrity XL Deluxe
www.pridemobility.com
27
I V. B AT T E R I E S A N D C H A R G I N G
It may take a few days for the temperature of your scooter’s batteries to stabilize and adjust to their new room or
ambient temperature. More importantly, it takes a few charging cycles (partial draining followed by full recharging)
to establish the critical chemical balance that is essential to a deep-cycle battery’s peak performance and long life.
Follow these steps to properly break in your scooter’s new batteries for maximum efficiency and service life.
1. Fully recharge any new battery prior to its initial use. This charging cycle brings the battery up to about 88% of
its peak performance level.
2. Operate your new scooter in familiar and safe areas. Drive slowly at first and do not travel too far from your
home or familiar surroundings until you have become accustomed to your scooter’s controls and have properly
broken in your scooter’s batteries.
3. Fully recharge the batteries. They should be at over 90% of their peak performance level.
4. Operate your scooter again.
5. Fully recharge the batteries again.
6. After four or five charging cycles, the batteries are able to receive a charge of 100% of their peak performance
level and are able to last for an extended period of time.
What about public transport?
If you intend to use public transport with your scooter, you must contact the transportation provider in advance to
determine their specific requirements.
28
www.pridemobility.com
Celebrity XL Deluxe
V.
O P E R AT I O N
BEFORE GETTING ONTO YOUR SCOOTER
! Have you fully charged the batteries? See IV. “Batteries and Charging.”
! Is the manual freewheel lever in the drive (rearward) position? Never leave the manual freewheel lever pushed
forward unless you are manually pushing your scooter.
! Is the tiller lock knob in the unlocked position? See VII. “Disassembly and Assembly.”
GETTING ONTO YOUR SCOOTER
1. Make certain that the key is removed from the key switch.
WARNING! Never attempt to get onto or off of your scooter without first removing the key
from the key switch. This will prevent the scooter from moving if accidental throttle control
lever contact is made.
2.
3.
4.
5.
6.
7.
8.
Stand at the side of your scooter.
Disengage the seat rotation lever and rotate the seat until it is facing you.
Make certain that the seat is fixed securely in position.
Position yourself comfortably and securely in the seat.
Disengage the seat rotation lever and rotate the seat until you are facing forward.
Make certain that the seat is fixed securely in position.
Make certain that your feet are safely on the floorboard.
PRE-RIDE ADJUSTMENTS AND CHECKS
! Is the seat at the proper height? See VI. “Comfort Adjustments.”
! Is the seat fixed securely in place?
! Is the tiller at a comfortable setting and locked securely in place? See VI. “Comfort Adjustments.”
! Is the key fully inserted into the key switch and turned clockwise to the “on” position?
! Does the scooter’s horn work properly?
! Is your proposed path clear of people, pets and obstacles?
! Have you planned your route to avoid adverse terrain and as many inclines as possible?
OPERATING YOUR SCOOTER
WARNING! The following can adversely affect steering and stability while operating your
scooter:
! Holding onto or attaching a leash to walk your pet
! Carrying passengers (including pets)
! Hanging any article from the tiller
! Towing or being pushed by another motorised vehicle
Such practices could cause loss of control and/or tipping resulting in personal injury and/
or damage to your scooter.
Keep both hands on the tiller and your feet on the floorboard at all times while operating your scooter. This driving
position gives you the most control over your vehicle.
Celebrity XL Deluxe
www.pridemobility.com
29
V.
O P E R AT I O N
! Set the speed adjustment dial to your desired speed.
! Push or pull the appropriate side of the throttle control lever.
! The electromechanical disc park brake automatically disengages and the scooter accelerates smoothly to the
speed you preselected with the speed adjustment dial.
! Pull on the left handgrip to steer your scooter to the left.
! Pull on the right handgrip to steer your scooter to the right.
! Move the tiller to the centre position to drive straight ahead.
! To stop, slowly release the throttle control lever. The electronic brakes will automatically engage, bringing your
scooter to a stop.
NOTE: Your scooter’s reverse speed is slower than that of the forward speed you preset with the speed
adjustment dial.
GETTING OFF YOUR SCOOTER
1. Bring your scooter to a complete stop.
2. Remove the key from the key switch.
3. Disengage the seat rotation lever and rotate the seat until you are facing toward the side of your scooter.
4. Make certain that the seat is fixed securely in position.
5. Carefully and safely get out of the seat and stand to the side of your scooter.
6. You can leave the seat facing to the side to facilitate boarding your scooter next time.
POWER DOWN TIMER FEATURE
Your scooter is equipped with an energy saving automatic power down timer feature designed to preserve your
scooter’s battery life. If you mistakenly leave the key in the key switch and in the “on” position but do not use your
scooter for approximately 20 minutes, the scooter’s controller shuts down automatically. Although the controller is
shut down, power will still be supplied to the scooter’s lighting system.
If the power down timer feature takes effect, perform the following steps to resume normal operation.
1. Remove the key from the key switch.
2. Reinsert the key and power up your scooter.
30
www.pridemobility.com
Celebrity XL Deluxe
VI.
COMFORT
TILLER ANGLE ADJUSTMENT
Your scooter is equipped with an adjustable pivoting tiller.
ADJUSTMENTS
TILLER ADJUSTMENT LEVER
WARNING! Remove the key from the
key switch before adjusting the tiller,
console or the seat. Never attempt to
adjust the tiller or the seat while the
scooter is in motion.
To change the tiller angle:
1. Squeeze the tiller adjustment lever. See figure 14.
2. Move the tiller to a comfortable position.
3. Release the tiller adjustment lever to lock the tiller into
place.
NOTE: In order to fully lower the tiller, you must
first remove the seat. Remove the seat by pulling it
straight up and off of the scooter.
TILLER CONSOLE ADJUSTMENT DIAL
Figure 14. Tiller/Tiller Console Adjustment
TILLER CONSOLE ANGLE ADJUSTMENT
The tiller console can be adjusted to different angles.
ADJUSTMENT DIAL
To change the console angle:
1. Loosen the adjustment dial (turn anticlockwise) and
move the tiller console up or down to a comfortable
riding position. See figure 14.
2. Hold the console at that position and tighten (turn
clockwise) the adjustment dial.
ARMREST ANGLE ADJUSTMENT
The armrest angle of your scooter can be adjusted upward or downward by turning the adjustment dial. See
figure 15.
Figure 15. Armrest Angle Adjustment
NOTE: Pivot the armrests upward to make getting
onto and off of your scooter easier.
SEATBACK ADJUSTMENT
WARNING! Do not operate your
scooter with the seatback in a
reclined position.
SEATBACK
ADJUSTMENT
LEVER
WARNING! Always keep your back
pressed firmly against the seatback
while adjusting the angle.
Figure 16. Seatback Adjustment
Celebrity XL Deluxe
www.pridemobility.com
31
VI.
COMFORT
ADJUSTMENTS
To adjust your scooter's reclining seat, perform these steps. See figure 16.
1. With your back pressed up against the seatback, lift up on the seatback adjustment lever and lean forward or
rearward to adjust the seatback angle.
2. Release the seatback adjustment lever once the seat is in a comfortable riding position.
SEAT ROTATION ADJUSTMENT
The seat rotation lever will secure the seat into several
positions.
1. Push forward on the seat rotation lever to disengage
the seat. See figure 16A.
2. Rotate the seat to the desired position.
3. Release the lever to secure the seat into place.
FRONT-TO-BACK SEAT ADJUSTMENT
You can reposition the seat forward or rearward to adjust
the distance between the seat and the tiller. See figure 16A.
1. Move the seat sliding lever outward.
2. While holding the lever out, slide the seat forward or
rearward.
3. Release the seat sliding lever once the seat is in the
desired position.
SEAT HEIGHT ADJUSTMENT
The seat can be repositioned to different heights. See
figure 17.
1. Remove the seat and rear shroud from your scooter.
See VII. “Disassembly and Assembly.”
2. Loosen the seat height adjustment nut and remove it
from the bolt. Remove the bolt.
3. Loosen the clamp-action bolt.
4. Raise or lower the upper seat post to the desired
seat height.
5. While holding the upper seat post at that height, match
up the locating holes in the upper seat post with those
of the lower seat post.
6. Insert the seat height adjustment bolt through the locating holes of both the upper and lower seat posts.
7. Install the nut onto the bolt and tighten.
8. Tighten the clamp-action bolt.
9. Reinstall the rear shroud and the seat.
32
SEAT ROTATION LEVER
SEAT SLIDING LEVER
Figure 16A. Seat Adjustment Levers
UPPER SEAT
POST
SEAT HEIGHT
ADJUSTMENT
NUT
LOCATING
HOLES
SEAT HEIGHT
ADJUSTMENT
BOLT
NUT
CLAMP-ACTION
BOLT
LOWER SEAT
POST
Figure 17. Seat Height Adjustment
www.pridemobility.com
Celebrity XL Deluxe
VI.
COMFORT
MIRROR POSITION
To install the mirror (see figure 18):
1. Determine a side to install the mirror and remove
the rubber plug from the top of the tiller handle.
2. Insert the threaded end of the mirror holder into the
opening and rotate it clockwise until snug.
3. If necessary, rotate the nut clockwise to secure the
mirror in place.
To adjust the mirror:
1. Position yourself in a seated driving position facing
forward.
2. Adjust the mirror left, right, up or down until you
have a good line of sight behind you.
ADJUSTMENTS
MIRROR HOLDER
PLUG
NUT
Figure 18. Mirror Installation
POSITIONING BELT (OPTIONAL)
Your scooter seat may be equipped with an auto-type
positioning belt that can be adjusted for operator comfort. See figure 19. The positioning belt is designed to
help support the operator so that he/she does not slide
down or forward in the seat. The positioning belt is not
designed for use as a restraining device.
To install the positioning belt (if required):
1. Remove the seat from your scooter.
2. Place the seat upside down so that you can see the
bottom of the seat base.
3. Remove the two bolts on the outermost part of the
rear seat mounting strap.
4. Insert the bolt through the appropriate end of the
positioning belt and then through the seat mounting
strap for each side of the scooter seat.
5. Tighten the bolts.
Figure 19. Positioning Belt
To adjust the positioning belt for operator comfort:
1. Insert the metal tab on the right side of the belt into the plastic housing on the opposite strap until you hear a
“click.”
2. Pull the strap on the right side of the belt until it is secure, but not so tight as to cause discomfort.
MANDATORY! Make sure the positioning belt is properly secured to the scooter and is
adjusted for operator comfort.
MANDATORY! Inspect the positioning belt for loose or damaged parts before each use of
the scooter. If you discover a problem, contact your authorised Pride Provider for
maintenance and repair.
Celebrity XL Deluxe
www.pridemobility.com
33
VI.
COMFORT
ADJUSTMENTS
POWER SEAT (OPTIONAL)
Your scooter may be equipped with a power seat. The power seat actuator is designed to raise or lower the seat
with minimal effort on the part of the operator. The power seat switch is located on the tiller console.
WARNING! The power seat is intended for operation only while your scooter is stationary
and on a level surface . Its pur pose is to aid you in r eaching objects .
Operating your power seat:
1. Release the throttle control lever and allow the scooter to come to a complete stop.
2. Ensure that your scooter is level and stationary.
3. Set the speed adjustment dial to the slowest setting.
4. Toggle the power seat switch located on the tiller console to the “on” position.
5. To raise the power seat, operate your throttle control lever in the forward direction.
6. Release the throttle control lever when you have attained your desired height.
7. To lower the power seat, operate your throttle control lever in the reverse direction.
8. Ensure that your seat is in the lowest position and that you have fully released the throttle control lever.
9. Toggle “off” the power seat switch before you attempt to drive your scooter again.
WARNING! Strict adherence to the following safety rules is vital to your safety:
! Do not switch the scooter power off while activating the throttle control lever or
immediately after release.
! Operate the power seat only while completely stationary on level ground.
! Do not attempt to operate the power seat switch with the throttle control lever
depressed.
! Do not operate your scooter with the power seat elevated.
! Never place your scooter in freewheel mode with the power seat elevated.
! Use extreme caution when reaching for objects with your power seat elevated. Do not
overextend or attempt to pick up objects that might affect your balance.
! Do not attempt to raise or lower the seat while in motion!
! Do not drive your scooter unless the power seat is fully retracted (in the lowest position).
34
www.pridemobility.com
Celebrity XL Deluxe
VII.
D I S A S S E M B LY
DISASSEMBLY
You can disassemble the scooter into seven pieces:
the seat, the front section, the rear section, the rear
shroud, the basket, and the batteries. See figure 20.
No tools are required to disassemble or assemble your
scooter, but keep in mind that the disassembled
sections of the scooter take up more floor space than
when assembled. Always disassemble or assemble
your scooter on a level, dry surface with sufficient
room for you to work and move around your scooterabout 2 metres in all directions. Remember that some
scooter components are heavy and you may need
assistance when lifting them.
WARNING! Do not lift beyond your
ph ysical capa bility. Ask for
assistance when necessary while
disassembling or assembling your
scooter.
AND
A S S E M B LY
REAR SECTION
SEAT
BATTERIES
REAR SHROUD FRONT SECTION
BASKET
Figure 20. The Scooter Disassembled
1. Place the scooter in drive mode by engaging the freewheel lever.
2. Lock the tiller in the straight ahead position by pushing the tiller lock knob in and turning it clockwise 90°. See
figure 21. The front wheel must face forward in order to lock the tiller.
3. Remove the seat by lifting it straight up and off of the scooter. If you encounter resistance when removing the
seat, disengage the seat rotation lever and swivel the seat back and forth while lifting up on the seat.
4. Gently pull the rear shroud up and off of the rear section of the scooter.
LOCKED POSITION
Figure 21. Tiller Lock Knob (Locked)
Celebrity XL Deluxe
UNLOCKED POSITION
Figure 21A. Tiller Lock Knob (Unlocked)
www.pridemobility.com
35
VII.
D I S A S S E M B LY
5. Unplug the front-to-rear and rear lighting harnesses by
squeezing the sides and pulling straight up. See figure 22.
6. Unplug both battery harnesses. Pull each harness
straight up. See figure 22.
7. Unfasten the battery tie-down strap and remove the
batteries from the battery wells.
AND
A S S E M B LY
REAR LIGHTING
HARNESS
WARNING! Failure to unplug both
battery harnesses, the front-to-rear
harness, and rear lighting harness
prior to separating the front and rear
sections could result in permanent
damage to the scooter.
Handbrake Cable Disconnect
1. Locate the quick disconnect body. See figure 23.
2. Pull the quick disconnect handle back from the quick
disconnect body.
3. Position the quick disconnect handle over the top of the
quick disconnect body.
4. Separate the brake cable from the cable clamp located
inside the quick disconnect body. See figure 24.
BATTERY HARNESSES
Figure 22. Harness Connections
QUICK DISCONNECT HANDLE
Frame Separation
1. Squeeze the tiller adjustment lever and lower the tiller
to its lowest point.
2. Lift up on the frame release lever. See figure 25.
3. Lift the front section up until the frame hooks of
the front section separate from the rear section.
See figure 26.
NOTE: Stabilise the rear section with your free hand
by holding onto the upper frame tube. See figure 26.
FRONT-TO-REAR HARNESS
QUICK
DISCONNECT
BODY
Figure 23. Quick Disconnect Handbrake Cable
4. Slowly separate the two sections. See figure 26.
ASSEMBLY
1. Position the front and rear sections of your scooter as
shown in figure 26.
2. Use the frame release lever to lift the front section as
you align the frame hooks of the front section with the
lower frame tube of the rear section. See figure 25.
3. Once the frame hooks are over the lower frame tube,
lower the front section completely. This will engage
the frame lock. See figure 25.
4. Raise the tiller.
36
Figure 24. Handbrake Cable Release
www.pridemobility.com
Celebrity XL Deluxe
VII.
D I S A S S E M B LY
5. Reconnect the handbrake cable.
6. Reinstall both batteries and secure with the tie-down
straps, making sure the strap is positioned over the
frame release lever to ensure proper securement.
7. Connect the front-to-rear harness, rear lighting harness, and both battery harnesses. See figure 22.
8. Reinstall the rear shroud.
9. Reinstall the seat and rotate it into place.
10. Unlock the front wheel by turning the tiller lock knob
90° anticlockwise. See figure 21A.
WARNING! After assembly, make
absolutely certain the tiller lock knob
is in the unlocked position before
riding your scooter.
AND
A S S E M B LY
FRAME RELEASE LEVER
FRAME LOCK
FRAME HOOK
Figure 25. Frame Release
LOWER FRAME TUBE
UPPER FRAME TUBE
FRAME HOOK
Figure 26. Frame Separation
Celebrity XL Deluxe
www.pridemobility.com
37
VIII.
BASIC
TROUBLESHOOTING
Any electromechanical device occasionally requires some troubleshooting. However, most of the problems that
may arise can usually be solved with a bit of thought and common sense. Many of these problems occur because
the batteries are not fully charged or because the batteries are worn down and can no longer hold a charge.
DIAGNOSTIC BEEP CODES
The diagnostic beep codes for your scooter are designed to help you perform basic troubleshooting quickly and
easily. A diagnostic beep code will sound in the event one of the conditions listed below develops.
NOTE: Your scooter will not run unless the beep code condition is resolved and the scooter has been
turned off, then turned back on.
BEEP CODE
!
!
!
!!!!
(1 ,1 )
C O N D IT IO N
S O L U T IO N
C o n tro lle r is h o t; th e sco o ter see m s
to b e lo sing p o w er.
S h u t d o w n yo ur sco o ter fo r a m in im u m
o f se ve ral m inu tes to allo w the co n tro ller
to c o o l.
B atte ry c h arg e is lo w .
C h a rg e b atte rie s a s so o n a s p o ssib le.
(1 ,4 )
! ! !
! ! !
!
!!
(1 ,2 )
!
!!!
!
!!!!!
(3 ,3 )
T hro ttle p o t fa ult
S p ee d p o t fau lt
(1 ,3 )
(1 ,5 )
!!!
!!!!!
!!!
!!!!
!!!
!!
(3 ,5 )
(3 ,4 )
(3 ,2 )
A tte m p tin g to o p era te the sc o o te r
w ith the c ha rg er atta ch ed .
T hro ttle co n tro l lev er no t a t ce nter
p o sitio n a t sta rt up .
T he m a n ua l fre e w h e el le ve r m a y b e
in the fre e w h e el (fo rw ard ) p o sitio n .
A b rak e fau lt ha s o cc urre d .
C o ntac t yo ur au tho rised P rid e P ro vid er
fo r a ssis ta nc e.
C o ntac t yo ur au tho rised P rid e P ro vid er
fo r a ssis ta nc e.
T ur n the sco o ter k e y to th e o ff p o sitio n .
S w itc h o ff the c ha rge r an d rem o ve d co rd
fro m th e ch ar ge r p o rt, the n re sta rt yo ur
sco o te r.
R e tur n the thro ttle c o ntro l le ve r to ce nter
p o sitio n, tu rn sco o ter o ff, a nd the n b ac k
o n.
T ur n th e sco o ter ke y to the o ff p o sitio n
P u sh the fre e w h e el le v er to th e d riv e
(rea rw a rd ) p o sitio n, the n re sta rt yo ur
sco o te r.
C o ntac t yo ur au tho rised P rid e P ro vid er
fo r a ssis ta nc e.
What if all the systems on my scooter seem to be “dead”?
! Make certain that the key is in the “on” position.
! Check that the batteries are fully charged.
! Push in the main circuit breaker reset button. See III. “Your Scooter.”
! Make certain that both battery harnesses and the front-to-rear harness are firmly connected. See VII. “Disassembly and Assembly.”
! Be sure the power down timer feature hasn’t been activated. See V. “Operation.”
38
www.pridemobility.com
Celebrity XL Deluxe
VIII.
BASIC
TROUBLESHOOTING
What if my scooter does not move when I engage the throttle control lever?
! When the manual freewheel lever is pushed forward, the brakes are disengaged and all power to the motor/
transaxle assembly is cut.
! Push rearward on the manual freewheel lever, turn the scooter off and then turn the scooter on to return to
normal scooter operation.
What if the main circuit breaker repeatedly trips?
! Charge the scooter’s batteries more frequently. See IV. “Batteries and Charging.”
! If the problem continues, have both of your scooter’s batteries load tested by your authorised Pride Provider.
! If the main circuit breaker trips repeatedly, contact your authorised Pride Provider for service.
! You may also perform the load test yourself. Battery load testers are available at most automotive parts stores.
! Follow the directions supplied with the load tester.
! See IV. “Batteries and Charging” or “Appendix I - Specifications” for information about your scooter’s
battery type.
What if the battery condition meter dips way down and the motor surges or hesitates when I engage the
throttle control lever?
! Fully charge your scooter’s batteries. See IV. “Batteries and Charging.”
! Have your authorised Pride Provider load test each battery.
! Or, see the previous troubleshooting question for load testing the batteries yourself.
If you experience any problems with your scooter that you are not able to solve, immediately contact your authorised
Pride Provider for information, maintenance and service.
Celebrity XL Deluxe
www.pridemobility.com
39
IX.
CARE
AND
MAINTENANCE
Your scooter requires a minimal amount of care and maintenance. If you do not feel confident in your ability to
perform the maintenance listed below, you may schedule inspection and maintenance at your authorised Pride
Provider. The following areas require periodic inspection and/or care and maintenance.
TYRE PRESSURE
! If equipped with pneumatic tyres, always maintain the psi/bar/kPa air pressure indicated on each tyre.
WARNING! It is important that the psi/bar/kPa air pressure indicated on each tyre be maintained
in pneumatic tyres at all times. Do not underinflate or overinflate your tyres. Low pressure may
result in loss of control, and overinflated tyres may burst. Failure to maintain the psi/bar/kPa air
pressure indicated on pneumatic tyres at all times may result in tyre and/or wheel failure.
! Regularly inspect your scooter’s tyres for signs of wear.
WHEEL REPLACEMENT
If your scooter is equipped with pneumatic tyres and you have a flat tyre, you can have the tube replaced. If your
scooter is equipped with a solid tyre insert, either the solid insert or the entire wheel must be replaced depending on
model. Contact your authorised Pride Provider for information regarding replacement wheels for your scooter.
WARNING! Wheels on your scooter should only be serviced/replaced by an authorized
Pride Provider or qualified technician.
WARNING! Completely deflate pneumatic tyres before dismantling the rim or attempting
repair.
WARNING! When changing a tyre, remove only the center lug nut, then remove the wheel.
If any further disassembly is required, deflate the tyre completely or it may explode.
EXTERIOR SURFACES
Bumpers, tyres, and trim can benefit from an occasional application of rubber or vinyl conditioner.
WARNING! Do not use a rubber or vinyl conditioner on the scooter’s vinyl seat or tyre tread,
as this may cause them to become dangerously slippery.
CLEANING AND DISINFECTION
! Use a damp cloth and mild, non-abrasive cleanser to clean the plastic and metal parts of your scooter. Avoid
using products that may scratch the surface of your scooter.
! If necessary, clean your product with an approved disinfectant. Make sure the disinfectant is safe for use on
your product before application.
WARNING! Follow all safety instructions for the proper use of the disinfectant before
applying it to your product.
ABS PLASTIC SHROUDS
! The shrouds of the scooter are formed from durable ABS plastic and are coated with an advanced formula
urethane paint.
! A light application of car wax will help the shrouds retain their high gloss.
40
www.pridemobility.com
Celebrity XL Deluxe
IX.
CARE
AND
MAINTENANCE
WIRING HARNESSES
! Regularly check all wiring connections.
! Regularly check all wiring insulation, including the charger power lead, for wear or damage.
! Have your authorised Pride Provider repair or replace any damaged connector, connection or insulation that
you find before using your scooter again.
BATTERY TERMINAL CONNECTIONS
! Make certain that the terminal connections remain tight and uncorroded.
! The batteries must sit flat in the battery wells.
! The battery terminals should face the rear of the scooter.
MOTOR BRUSHES
The motor brushes are housed inside of the motor transaxle/assembly. They should be inspected periodically for
wear by your authorised Pride Provider.
AXLE BEARINGS AND THE MOTOR/TRANSAXLE ASSEMBLY
You do not need to lubricate these items, as they are all prelubricated and sealed
CONSOLE, CHARGER, AND ELECTRONIC CONTROLLER MODULE
! Keep these areas away from moisture.
! Before operating your scooter, allow any of these areas to dry thoroughly if they have been exposed to
moisture.
HANDBRAKE
The handbrake lever may require periodic adjustment to maintain proper operation. Contact your authorised Pride
Provider for more information.
FUSES
To replace a fuse:
1. Remove the fuse by pulling it straight out of its slot.
2. Examine the fuse to be sure it is blown. See figures 27 and 27A.
3. Insert a new fuse of the proper rating.
WARNING! The replacement fuse must exactly match the rating of the new fuse. Failure
to use properly rated fuses may cause damage to the electrical system.
Figure 27. Working Fuse
Celebrity XL Deluxe
Figure 27A. Blown Fuse (Replace)
www.pridemobility.com
41
IX.
CARE
AND
MAINTENANCE
NYLON LOCK NUT REPLACEMENT
Any nylon insert lock nut removed during the periodic maintenance, assembly or disassembly of the scooter must
be replaced with a new nut. Nylon insert lock nuts should not be reused as it may cause damage to the nylon insert,
resulting in a less secure fit. Replacement nylon insert lock nuts are available at local hardware stores or through
your authorised Pride Provider.
STORING YOUR SCOOTER
If you plan on not using your scooter for an extended period of time, it is best to:
! Fully charge its batteries prior to storage.
! Disconnect both battery harnesses.
! Store your scooter in a warm, dry environment.
! Avoid storing your scooter where it will be exposed to temperature extremes.
WARNING! Always protect batteries from freezing temperatures and never charge a frozen
battery.
Batteries that are regularly and deeply discharged, infrequently charged, stored in extreme temperatures or stored
without a full charge may be permanently damaged, causing unreliable performance and limited service life. It is
recommended that you charge the scooter batteries periodically throughout periods of prolonged storage to ensure
proper performance.
You may wish to place several boards under the frame of your scooter to raise it off of the ground during periods
of prolonged storage. This takes the weight off the tyres and reduces the possibility of flat spots developing on the
areas of the tyres contacting the ground.
DISPOSAL OF YOUR SCOOTER
Your scooter must be disposed of according to applicable local and national statutory regulations. Contact your
local waste disposal agency or authorised Pride Provider for information on proper disposal of packaging, metal
frame components, plastic components, electronics, and batteries.
42
www.pridemobility.com
Celebrity XL Deluxe
X. WARRANTY
TWO-YEAR LIMITED WARRANTY
Structural frame components, including: platform, fork, seat post, and frame welds.
Drivetrain, including: differential, motor, and brake.
ONE-YEAR LIMITED WARRANTY
Your Pride Scooter is fully guaranteed for twelve (12) months from the date of purchase against faults arising due
to defects in manufacture or materials. This warranty does not detract from, but is in addition to your legal rights.
All electronic parts, including controllers and battery chargers, have a one (1) year warranty. Servicing to the
controller or battery charger must be carried out by your authorised Pride Provider. Any attempt to open or
dismantle these items renders the guarantee void on that item.
NOT COVERED UNDER WARRANTY
This guarantee does not extend to those items which may need replacement due to normal wear and tear (tyres,
belts, bulbs, upholstery, plastic shrouds, motor brushes, fuses, and batteries) or damage to the product caused by
misuse or accident for which Pride or its agent cannot be held responsible. This warranty does not include labour
or service calls.
BATTERIES
Batteries are covered by a six (6) month warranty from the original manufacturer.
Gradual deterioration in performance due to being left in a discharged state, left in cold conditions for long periods
of time or worn out through heavy use is not covered.
SERVICE CHECKS AND WARRANTY SERVICE
Warranty service can be performed by an authorised Pride Provider. Please contact your authorised Pride Provider for advice on the current cost affecting the service visit.
REPLACEMENT UNITS
The availability of replacement units is subject to the discretion of the provider, not the manufacturer. For more
information regarding replacement units, contact your authorised Pride Provider.
Celebrity XL Deluxe
www.pridemobility.com
43
APPENDIX
Model Number
Class Of Use
Maximum Safe Slope
Maximum Climbing Ability
Maximum Obstacle Climbing Ability
2
Overall Length
2
Overall Width
Total Weight
Total Weight Without Batteries
Heaviest Piece When Disassembled
Turning Radius2
1
Speed (Maximum)
1
Range Per Charge
2
Ground Clearance
Weight Capacity
Standard Seating
Drive System
Dual Braking System
Tyres
3
Battery Requirements
Battery Charger
1
2
3
I
-
S P E C I F I C AT I O N S
SC4450DXAUS
B
See figure 1.
See figure 1.
5 cm
130.17 cm
64.13 cm
112 kg
90.71 kg
Front section: 37.64 kg
168.27 cm
Variable up to 15 km/h
(With 31-36 Ah batteries) Up to 40.23 km
10.79 cm
181 kg
Type: CRS Deluxe
Weight: 23.13 kg
Material: Vinyl
Dimensions: 45.72 cm width
45.72 cm depth
68.58 cm height
Rear-wheel drive, sealed transaxle, 24-volt DC motor
Electronic, regenerative, and electromechanical
Type: pneumatic:
Front: 10.16 cm x 33.02 cm
Rear: 10.16 cm x 33.02 cm
Two 12-volt, deep-cycle
Size: U1 (31-36 Ah)
Weight: 11.11 kg each
Off-board
Varies with user weight, terrain type, battery amp-hour (Ah), battery charge, battery condition, and tyre condition. This
specification canbe subject to a variance of (+ or -) 10%.
Due to manufacturing tolerances and continual product improvement, this specification can be subject to a variance of
(+ or – ) 3 %.
AGM or Gel-Cell type required. See IV. “Batteries and Charging.”
NOTE: All specifications subject to change without notice.
44
www.pridemobility.com
Celebrity XL Deluxe
APPENDIX
I
-
S P E C I F I C AT I O N S
130.17 cm
16"
45.72 cm
45.72 cm
Turning Radius
168.27 cm
64.13 cm
68.58 cm
125.73 cm - 135.89 cm
43.18 cm - 53.34 cm
10.79 cm
Figure 28. Scooter Dimensions
10.16 cm
33.02 cm
10.16 cm
33.02 cm
FRONT
REAR
Figure 29. Tyre Dimensions
Celebrity XL Deluxe
www.pridemobility.com
45
NOTES
46
www.pridemobility.com
Celebrity XL Deluxe
NOTES
Celebrity XL Deluxe
www.pridemobility.com
47
Mobility Products Australia Pty. Ltd.
*INFMANU3341*