Canon REALiS SX7 Mark II D User`s manual

Table of contents/Safety Instructions
Before Use
MULTIMEDIA PROJECTOR
Setting Up the Projector
Projecting an Image from the Computer
Projecting an Image from AV Equipment
User’s Manual
Useful Functions Available During a Presentation
Setting Up Functions from Menus
Maintenance
Troubleshooting
Appendix
Index
ENG
Downloaded From projector-manual.com Canon Manuals
Quick Reference – How to start projection
Computer
1.
Install the projector.
2.
Connect the projector.
3.
Turn on the projector.
4.
Press the
5.
Set up the computer.
6.
Select the input signal by pressing the
7.
Press the
8.
Press the
9.
Select the image mode with the
P32-33
z Install the projector at the desired distance from the screen.
P36-39
z Connect the projector and the computer with a cable.
P40-41
z Connect the power cord and turn on the projector.
z Adjust the height of the projecting image (P43).
z Select a display language when turning on the projector for the first time (P41).
button twice.
P46-47
z Adjust the focus of the screen.
P44-45
z Turn on the computer and set the resolution.
button.
P48-50
z Select an appropriate input signal in accord with the signal from the computer.
button twice again.
P46-47
z Adjust the input signal, focusing, keystone distortion, etc. automatically with the
auto setup function.
button.
P54
z Optimize the input signal with the auto PC function (Skip this step if the projector
is projecting an image properly.)
button.
P55-56
z Select an appropriate image mode for projection.
z Specify the aspect ratio or display area in the [Aspect] menu as required (P57,
90).
10. Start the presentation.
P78-83
z Set the useful functions available during the presentation from the remote control.
Finishing the projection...
Turn off the projector
z Turn off the projector and unplug the power cord.
Downloaded From projector-manual.com Canon Manuals
2
P60-61
AV Equipment
1.
Install the projector.
2.
Connect the projector.
3.
Turn on the projector.
4.
Press the
5.
Set up the AV equipment.
6.
Select the input signal by pressing the
7.
Press the
8.
Select the image mode with the
P32-33
z Install the projector at the desired distance from the screen.
z Install batteries in the remote control (P29)
P64-68
z Connect the projector and the AV equipment with a cable* (see P38, 39 for the
instruction on connecting a audio cable).
P40-41
z Connect the power cord and turn on the projector.
z Adjust the height of the projecting image (P43).
z Select a display language when turning on the projector for the first time (P41).
button twice.
P46-47
z Adjust the focus of the screen.
z Turn on the AV equipment and play the video image.
button.
P70-72
z Select DIGITAL VIDEO as the input signal for a digital video image.*
For the other video image, go to step 7.
button twice again.
P70
z Adjust the input signal, focusing, keystone distortion, etc. automatically with the
auto setup function.
button.
P55-56
z Select an appropriate image mode for projection.
z Specify the aspect ratio or display area in the [Aspect] menu as required (P73,
90, 91).
Finishing the projection...
Turn off the projector
P60-61
z Turn off the projector and unplug the power cord.
*
Connect the projector and the AV equipment with a HDMI/DVI cable to project a digital video
image (P65).
Downloaded From projector-manual.com Canon Manuals
3
Table of Contents
Quick Reference – How to start projection............................................................. 2
Table of Contents ................................................................................................... 4
TABLE OF CONTENTS
Safety Instructions.................................................................................................. 7
Safety Precautions............................................................................................................ 8
AC Power Cord Requirement ......................................................................................... 11
Federal Communication Commission Notice ................................................................. 12
Canadian Radio Interference Regulations ..................................................................... 12
Precautions on Handling the Batteries in the Remote Controller ................................... 13
Lamp Handling Precautions........................................................................................... 13
Carrying/Transporting the Projector ............................................................................... 14
Installation Precautions .................................................................................................. 14
Features of the Multimedia Projector SX7 MarkII/SX60....................................... 16
Supplied Manuals and Symbols Used in This Manual ......................................... 17
Supplied Manuals........................................................................................................... 17
Before Use ........................................................................................................... 20
Supplied Accessories .................................................................................................... 20
Part Names..................................................................................................................... 22
Preparing the Remote Control........................................................................................ 29
Setting Up the Projector ....................................................................................... 32
Determining the Distance to the Screen ........................................................................ 32
Determining the Installation Position .............................................................................. 33
Projecting an Image from the Computer .............................................................. 36
Connecting the Projector to the Computer..................................................................... 36
Starting Projection .......................................................................................................... 40
Adjusting the Image ....................................................................................................... 42
Preparing the Computer................................................................................................. 44
Performing the Auto Setup ............................................................................................. 46
Adjusting the Focus........................................................................................................ 51
Adjusting Keystone Distortion ........................................................................................ 52
Setting Up the Computer Screen Automatically (AUTO PC).......................................... 54
Selecting an Image Mode (IMAGE) ............................................................................... 55
Selecting a Screen Mode (Aspect) ................................................................................ 57
Selecting Aspect Ratio of the Projecting Image (Screen aspect) .................................. 59
Turning Off the Projector ................................................................................................ 60
Projecting an Image from AV Equipment ............................................................. 64
Connecting the Projector to an AV Equipment............................................................... 64
Projecting a Video Image from an AV Equipment.......................................................... 69
Performing the Auto Setup ............................................................................................. 70
Selecting a Screen Mode (Aspect) ................................................................................ 73
Selecting Aspect Ratio of the Projecting Image (Screen aspect) .................................. 74
Downloaded From projector-manual.com Canon Manuals
4
Useful Functions Available During a Presentation ............................................... 78
Setting Up Functions from Menus ........................................................................ 86
How to Use Menus ......................................................................................................... 86
Setting Display Status .......................................................................................... 90
Selecting a Screen Mode (1).......................................................................................... 90
Selecting a Screen Mode (2).......................................................................................... 90
Selecting a Screen Mode (3).......................................................................................... 91
Selecting an Input Signal Type (1) ................................................................................. 91
Selecting an Input Signal Type (2) ................................................................................. 92
Selecting an Input Signal Type (3) ................................................................................. 92
Adjusting the Total Number of Dots ............................................................................... 93
Adjusting the Tracking ................................................................................................... 93
Adjusting the Horizontal Position.................................................................................... 94
Adjusting the Vertical Position........................................................................................ 94
Adjusting the Number of Horizontal Pixels..................................................................... 95
Adjusting the Number of Vertical Pixels ......................................................................... 95
Performing Progressive Processing ............................................................................... 96
Selecting a Menu Position .............................................................................................. 96
Performing the Ceiling-mounted/Rear Projection ........................................................... 97
Correcting the Screen Color........................................................................................... 98
Capturing a Logo to Be Projected (SX60) ...................................................................... 98
Selecting a Logo Display Position (SX60) ...................................................................... 99
Displaying a Logo (No signal screen) ............................................................................ 99
Displaying a Logo (NO SHOW).................................................................................... 100
Selecting a Logo at Startup.......................................................................................... 100
Selecting Aspect Ratio of the Screen........................................................................... 101
Setting the Image Quality ................................................................................... 102
Selecting an Image Mode ............................................................................................ 102
Adjusting the Brightness .............................................................................................. 103
Adjusting the Contrast.................................................................................................. 103
Adjusting the Sharpness .............................................................................................. 104
Making a Gamma Correction ....................................................................................... 104
Making Color Adjustment (1) (SX7 II) ........................................................................... 105
Making Color Adjustment (2)........................................................................................ 105
Making Color Adjustment (3)........................................................................................ 106
Making Advanced Color Adjustment (1) ...................................................................... 106
Downloaded From projector-manual.com Canon Manuals
5
TABLE OF CONTENTS
Blackened Out an Image Temporarily ........................................................................... 78
Freezing the Picture ....................................................................................................... 78
Muting the Sound ........................................................................................................... 79
Adjusting the Volume ..................................................................................................... 79
Showing the Elapsed Time............................................................................................. 80
Page Up or Down through the Pages ............................................................................ 80
Zooming an Image ......................................................................................................... 81
Operating a Mouse with the Remote Control ................................................................. 82
Pointing with a Spotlight ................................................................................................. 83
TABLE OF CONTENTS
Making Advanced Color Adjustment (2) ...................................................................... 107
Making Advanced Color Adjustment (3) ...................................................................... 107
Correcting the Image According to the Ambient Light (SX7 II) ................................... 108
Reducing the Lamp Brightness.................................................................................... 109
Resetting the Image Settings ....................................................................................... 110
Setting Various Function .................................................................................... 111
Setting Auto Setup Function......................................................................................... 111
Selecting the Power Management Mode ..................................................................... 111
Skip the POWER Button Operation .............................................................................. 112
Enabling/Disabling the Beep........................................................................................ 112
Selecting a Display Language ..................................................................................... 113
Prohibiting the Projector Operation .............................................................................. 114
Enabling/Disabling the Guide Message....................................................................... 114
Turning On/Off the LED Illumination............................................................................. 115
Setting up the Remote Control ..................................................................................... 115
Setting up the Digital Video Input Signal ..................................................................... 116
Setting a Password....................................................................................................... 116
Registering a Password ............................................................................................... 117
Resetting to the Default Setting.................................................................................... 117
Resetting the Lamp Counter ........................................................................................ 118
Maintenance....................................................................................................... 120
Cleaning the Projector.................................................................................................. 120
Cleaning and Replacing the Air Filter .......................................................................... 121
Replacing the Lamp ..................................................................................................... 122
Troubleshooting.................................................................................................. 126
WARNING Lamp Flash Patterns................................................................................... 126
Symptoms and Solutions.............................................................................................. 127
Appendix ............................................................................................................ 132
Supported Computer Signal Types.............................................................................. 132
Relationship between Screen Size and Projecting Distance ....................................... 133
Glossary ....................................................................................................................... 134
Specifications ............................................................................................................... 138
Index .................................................................................................................. 140
Menu Configuration ............................................................................................ 144
Downloaded From projector-manual.com Canon Manuals
6
Safety Instructions
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). THERE ARE NO USER-SERVICEABLE PARTS
INSIDE EXCEPT LAMPS. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
THIS SYMBOL INDICATES THAT DANGEROUS VOLTAGE CONSTITUTING A RISK OF ELECTRIC SHOCK IS PRESENT WITHIN THIS UNIT.
THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT OPERATING
AND MAINTENANCE INSTRUCTIONS FOR THIS UNIT IN THE OWNER'S
MANUAL.
CAUTION
Not for use in a computer room as defined in the Standard for the Protection of Electronic
Computer/Data Processing Equipment, ANSI/NFPA 75.
Downloaded From projector-manual.com Canon Manuals
7
SAFETY INSTRUCTIONS
Before operating this projector, read this manual thoroughly in order to operate the
projector properly.
This projector offers many convenient features and functions. Operating the projector
properly enables you to manage those features and maintain it in good condition for a long
period.
Improper operation may result in not only reducing the product-life, but also malfunctions,
fire hazards, or other accidents.
If your projector is not operating correctly, read this manual again, check operations and
cable connections, and try the solutions shown in the "Troubleshooting" section at the end
of this booklet. If the problem still persists, contact the service center or the dealer where
you purchased the projector.
Safety Precautions
SAFETY INSTRUCTIONS
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE.
z This projector projects intense light from the projection lens. Do not stare directly into
the lens if possible, as doing so may result in eye damage. Be especially careful that
children do not stare directly into the beam.
z Install the projector in an appropriate position.
Installing the projector in an inappropriate position may result in a fire hazard.
z Allow for appropriate space above beside and behind of the projector cabinet for
allowing air circulation and cooling of the projector. Minimum clearances must be
maintained. If the projector is to be built into a compartment or similarly space, the
minimum distances must be maintained. Do not cover the ventilation slot on the
projector. Heat build-up can reduce the service life of your projector, and can also be
dangerous.
SIDE and TOP
REAR
1 m (3.3')
1 m (3.3')
1 m (3.3')
1 m (3.3')
z Do not put any flammable objects or spray cans near the projector, as the hot air
exhausted from the ventilation holes may result in an explosion.
z If the projector is not to be used for an extended period of time, unplug it from the
power outlet.
Downloaded From projector-manual.com Canon Manuals
8
READ AND KEEP THIS OWNER'S MANUAL FOR LATER USE.
Read all of the instructions given here and retain them for later use. Unplug this projector
from the AC power supply before cleaning. Do not use liquid or aerosol cleaners on the
projector. Use a damp cloth for cleaning.
Follow all warnings and instructions marked on the projector.
For added protection of the projector during a lightning storm, or when it is left unattended
or unused for long periods of time, unplug it from the wall outlet. This will prevent damage
due to lightning and power surges.
Do not expose this unit to rain or use near water... for example, in a wet basement, near a
swimming pool, etc...
Do not use attachments not recommended by the manufacturer as they may result in
hazards.
Do not place this projector on an unstable cart, stand, or table. The projector may fall,
causing serious injury to a child or adult, and serious damage to the projector. Use only
with a cart or stand recommended by the manufacturer, or sold with the projector. Wall or
shelf mounting should be carried out in accordance with the manufacturer's directions, and
should use a mounting kit approved by the manufacturers.
An appliance and cart combination should be moved with care.
Sudden stops, excessive force, and uneven surfaces may cause the
appliance and cart combination to overturn.
Slots and openings in the back and bottom of the cabinet are provided
for ventilation, to insure reliable operation of the equipment and to
protect it from overheating.
The openings should never be covered with cloth or other materials, and the bottom
opening should not be blocked by placing the projector on a bed, sofa, rug, or other
similar surface. This projector should never be placed near or over a radiator or heat
register.
This projector should not be placed in a built-in installation such as a book case unless
proper ventilation is provided.
Downloaded From projector-manual.com Canon Manuals
9
SAFETY INSTRUCTIONS
All the safety and operating instructions should be read before beginning to operate the
product.
SAFETY INSTRUCTIONS
Never push objects of any kind into this projector through cabinet slots as they may touch
dangerous voltage points or short out parts that could result in a fire or electric shock.
Never spill liquid of any kind onto the projector.
Do not install the projector near the ventilation duct of air-conditioning equipment.
This projector should be operated using only the type of power source indicated on the
marking label. If you are not sure of the type of power supplied, consult your authorized
dealer or local power company.
Do not overload wall outlets and extension cords as this can result in fire or electric shock.
Do not allow anything to rest on the power cord. Do not locate this projector where the
cord may be damaged by people walking on it.
Do not attempt to service this projector yourself as opening or removing covers may
expose you to dangerous voltages or other hazards. Refer all servicing to qualified service
personnel.
Unplug this projector from the wall outlet and refer servicing to qualified service personnel
under the following conditions:
a. When the power cord or plug is damaged or frayed.
b. If liquid has been spilled into the projector.
c. If the projector has been exposed to rain or water.
d. If the projector does not operate normally after following the operating instructions.
Adjust only those controls that are covered in the operating instructions as improper
adjustment of other controls may result in damage and will often require extensive work
by a qualified technician to restore the projector to normal operating condition.
e. If the projector has been dropped or the cabinet has been damaged.
f. When the projector exhibits a distinct change in performance-this indicates a need for
servicing.
When replacement parts are required, be sure the service technician uses replacement
parts specified by the manufacturer that have the same characteristics as the original
parts. Unauthorized substitutions may result in fire, electric shock, or injury.
Upon completion of any service or repairs to this projector, ask the service technician to
perform routine safety checks to determine that the projector is in safe operating condition.
Downloaded From projector-manual.com Canon Manuals
10
AC Power Cord Requirement
AC Power Cord for the United States and Canada:
The AC Power Cord used in the United States and Canada is
listed by the Underwriters Laboratories (UL) and certified by the
Canadian Standard Association (CSA).
The AC Power Cord has a grounding-type AC line plug. This is a
safety feature to ensure the plug fits into the power outlet. Do
not try to tamper with this safety feature. Should you be unable
to insert the plug into the outlet, contact your electrician.
Ground
THE SOCKET-OUTLET SHOULD BE INSTALLED NEAR THE EQUIPMENT AND EASILY
ACCESSIBLE.
NOTE FOR CUSTOMERS IN THE US
LAMP(S) INSIDE THIS PRODUCT CONTAIN MERCURY AND MUST BE RECYCLED
OR DISPOSED OF ACCORDING TO LOCAL, STATE OR FEDERAL LAWS.
European Union (and EEA) only.
These symbols indicate that this product is not to be disposed of with your
household waste, according to the WEEE Directive (2002/96/EC), the
Battery Directive (2006/66/EC) and/or your national laws implementing
those Directives. If a chemical symbol is printed beneath the symbol shown
above, in accordance with the Battery Directive, this indicates that a heavy
metal (Hg = Mercury, Cd = Cadmium, Pb = Lead) is present in this battery
or accumulator at a concentration above an applicable threshold specified
in the Battery Directive. This product should be handed over to a
designated collection point, e.g., on an authorized one-for-one basis when
you buy a new similar product or to an authorized collection site for
recycling waste electrical and electronic equipment (EEE) and batteries
and accumulators. Improper handling of this type of waste could have a
possible impact on the environment and human health due to potentially
hazardous substances that are generally associated with EEE. Your
cooperation in the correct disposal of this product will contribute to the
effective usage of natural resources. For more information about the
recycling of this product, please contact your local city office, waste
authority, approved scheme or your household waste disposal service or
visit
www.canon-europe.com/environment.
(EEA: Norway, Iceland and Liechtenstein)
Downloaded From projector-manual.com Canon Manuals
11
SAFETY INSTRUCTIONS
The AC Power Cord supplied with this projector meets the requirements for use in the
country you purchased it.
Federal Communication Commission Notice
SAFETY INSTRUCTIONS
Multimedia Projector, Model: SX7 MarkII/SX60
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may
cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
z Reorient or relocate the receiving antenna.
z Increase the separation between the equipment and receiver.
z Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
z Consult the dealer or an experienced radio/TV technician for help.
The cable with a ferrite core provided with the projector must be used with this
equipment in order to comply with Class B limits in Subpart B of Part 15 of the FCC rules.
Use of a shielded cable is required to comply with class B limits in Subpart B of Part 15
of FCC Rules.
Do not make any changes or modifications to the equipment unless otherwise specified
in the instructions. If such changes or modifications should be made, you could be
required to stop operation of the equipment.
Canon U.S.A. Inc.
One Canon Plaza, Lake Success, NY 11042-1198, U.S.A.
Tel No. (516) 328-5600
Canadian Radio Interference Regulations
This Class B digital apparatus complies with Canadian ICES-003.
Downloaded From projector-manual.com Canon Manuals
12
Precautions on Handling the Batteries in the Remote Controller
Warning
Observe the following precautions when handling the batteries. Failure to do so
may cause explosion, heat generation, fire or leakage of the battery fluid.
z Remove the batteries when they have been exhausted or not in use for an
extended period of time.
z Be sure to replace both batteries at the same time. Do not mix batteries of
different types.
z Insert batteries correctly according to the "+" and "–" markings.
z If a fluid from a battery leaks and comes in contact with your skin, rinse the
affected skin thoroughly as soon as possible.
Lamp Handling Precautions
This projector uses a high-pressure mercury lamp which must be handled carefully and
correctly as mentioned below.
The mercury lamp has the following characteristics.
z A lamp may explode with a loud sound or burn out due to a shock, scratch, or use
beyond its expiry date.
z The lamp life may differ from lamp to lamp and according to the usage environment.
There is no guarantee that all lamps will last for the same period of time. Some lamps
may fail in a shorter period of time than other similar lamps.
z A lamp gradually becomes darker over time.
Warning
Caution
If a Lamp Explodes
z If a lamp explodes, gas or dust may come out of the exhaust vent. Open
windows and doors for ventilation.
z The gas contains toxic mercury. Always keep your face away from the
exhaust vent when the projector is operating to avoid inhaling mercury
vapors or to prevent it from getting in your eyes or mouth.
z If you inhale the gas or the shards of the broken lamp contact your eyes or
mouth, consult a doctor immediately.
z If a lamp explodes, its shards may scatter inside the projector. Ask the
Canon service representative to clean and check the inside of the projector
and replace the lamp.
If the projector indicates that the lamp should be replaced (i.e., the LAMP
REPLACE indicator lights up twice),
z The chances of an explosion increase. Replace the lamp with a new one
immediately if such is the case.
Downloaded From projector-manual.com Canon Manuals
13
SAFETY INSTRUCTIONS
Caution
Observe the following precautions when handling the batteries. Failure to do so
may cause explosion, heat generation, fire, or leakage of the battery fluid.
z Do not heat or disassemble the batteries, or throw them into fire.
z Do not attempt to recharge the batteries.
SAFETY INSTRUCTIONS
Caution
Disposal of Waste Lamp
z Dispose of the projector's mercury lamp according to local regulations just
like the fluorescent lamps.
Carrying/Transporting the Projector
Caution
z This projector is a precision machine. Do not subject the projector to strong
shocks or vibrations or turn it down.
z Install the lens cap to protect the lens and put the projector in the carrying
bag to protect it from dust and scratches on the surface of it when you carry
the projector. For details, see P21.
z Wait until the cooling fan stops before putting the projector in the carrying
bag. Do not put the projector in the carrying bag until the cooling fan stops
rotating. The projector may be damaged due to the heat.
z Replace the adjustable foot before putting the projector in the carrying bag.
The projector may be damaged if you put it in the bag without replacing the
adjustable foot.
z The carrying bag is not designed to protect the projector from external
shocks. When carrying the projector with it put in the carrying bag, do not
give a shock to it, drop it, or place anything on it. The projector may be
damaged or malfunctioned.
z Do not transport the projector through a courier or transport service with the
carrying bag. Put the projector in an impact-resistant transport case if such
is the case.
Installation Precautions
Caution
The area around the exhaust vent and the cabinet above the exhaust vent
become hot when the projector is operating.
z Do not touch these areas, or you may get burnt. In particular, keep children
away from these areas. Do not put anything that may deform or discolor due
to heat on the projector.
Hot air is exhausted from the exhaust vent.
Observe the following:
z Do not put any metallic object on the
projector. It may become hot, resulting in
accident or injury.
z Do not seat anyone near the exhaust vent.
Otherwise, you may get burned.
Downloaded From projector-manual.com Canon Manuals
14
Hot air
Position the projector in a horizontal position. Incorrect installation may cause
troubles and accidents.
z Do not tilt the projector more than 20
degrees above and below the horizontal.
20°
z When you want to use your projector
pointing up or down, make sure to place
20°
the projector straight up or down.
Do Not Use in the Following Environments
z Do not place the projector on an unstable or slanted surface. The projector
may fall causing a personal injury.
z Do not place it in an oily, smoky, or damp location (e.g., near a cooking table
or a humidifier). It may cause a fire or an electric shock.
z Place the projector with a minimum distance of 1 m (3.3') from its left, right,
rear, and top panels to the neighboring object such as a wall. Otherwise, it
may damage the projector due to bad exhaust ventilation.
z Do not put anything near the exhaust vent that may deform or deteriorate
due to heat.
z Do not install the projector in a humid or dusty location or a position where
there is a lot of oily or cigarette smoke. Optical parts such as a lens and
mirror may be stained, resulting in poor picture quality.
z Do not place it near an exhaust outlet of air-conditioning equipment.
Otherwise, it may be damaged.
If the projector is carried from a cold place to a warm place or the room
temperature is raised rapidly, condensation may form on the lens and mirror due
to the moisture in the atmosphere, resulting in a blurred picture. Wait until
condensation evaporates and normal picture is shown.
Do not use the projector in a place subject to either very high or very low
temperatures. Doing so may cause malfunction. The ranges of the operating
and storage temperatures are as shown below:
Operating temperature: +5°C to +35°C (Humidity: 85% or below)
Storage temperature: -10°C to +60°C
Using the Projector at 2300 Meters or More Above Sea Level
z If you use the projector at 2300 meters or more above sea level, the special
configuration is required to cool down the projector properly. Contact your
dealer.
Downloaded From projector-manual.com Canon Manuals
15
SAFETY INSTRUCTIONS
Caution
When placing the projector on a castered stand or table, be sure to lock the
casters.
z Failure to do so may cause the projector to move or topple, resulting in an
injury.
Features of the Multimedia Projector
SX7 MarkII/SX60
Thank you for purchasing a Canon projector.
The MULTIMEDIA PROJECTOR SX7 MarkII/SX60 are high-performance projectors which
project the data from the computer and the moving picture from the DVD player to the big
screen.
Major Features
Smooth and Beautiful Imaging Capability
Incorporation of AISYS, Canon's unique optical engine, and LCOS (Liquid Crystal On Silicon) achieves high brightness, high contrast ratio, and smooth and beautiful lattice-free
images.
Super-Silent Operation of 27dB* (SX60)
This projector achieves super-silence operation as low as 27dB which creates a comfortable atmosphere where you can concentrate on watching a movie.
* At the [Quiet] lamp mode.
Native SXGA+ Resolution
Native SXGA+ resolution (1400 by 1050 dots) ensures projection of a high-quality image in
a wider projection area with a high degree of resolution.
High-powered 1.7X Zoom Lens
1.7X zoom aspheric lens can project a 100-inch image when placed 3 m (9.8') to 4.9 m
(16.0') away.
"Auto Setup Function" for Easy Installation
The "Auto Setup Function" allows you to install the projector easily by automatically adjusting focus and keystone distortion.
Adobe®RGB Color Space Compatibility (SX7 II)
AdobeRGB color space compatibility achieves faithful color reproduction.
"Home Cinema" Mode Reproducing the Atmosphere of a Movie Theater (SX60)
You can reproduce the atmosphere of a full-scale movie theater in your home by selecting
"Home Cinema" from the image mode.
"Off and Go" Function Allowing the Carriage Immediately After the Use
You can carry the projector immediately after the use because the cooling fan keeps rotating even if the power cord is removed from the electrical outlet.
* Never put the projector in the bag when the cooling fan is rotated.
Various Image Modes for a Particular Use of Your Projector (SX7 II)
When projecting a digital still photo image or an image that has been processed on an
sRGB-compatible monitor, you can project the image with higher tone on the screen by
incorporating the appropriate image correction function for the particular lighting environment.
It is useful when projecting the image in a photo studio, portrait studio, wedding reception
hall, art museum, gallery, etc.
Downloaded From projector-manual.com Canon Manuals
16
Supplied Manuals and Symbols Used in This
Manual
Supplied Manuals
User’s Manual (This Document)
This is a universal manual for the projector, SX7 MarkII/SX60. This manual provides
detailed information on how to use the projectors. Read this manual thoroughly to make the
most of your projector and ensure safety.
Important Information and Quick Start Guide
First read document. It provides information about projector safety, cautions, quick start
guide*, cleaning and replacing the air filter and lamp replacement.
* This guide shows an outline flowchart of the steps to start and stop the projector, as well
as the functions available for projecting images.
Symbols of Button Operations
This projector can be operated using buttons on the remote control or the top control on
the main unit. The remote control allows you to operate all functions of the projector.
In this manual, the button operation is shown as below.
Adjusting the Focus
You can adjust the focus.
Follow the steps below to adjust the focus manually if the Auto setup function (Auto
not adjust the focus appropriately.
Indicates the button operation on the top control.
1
Press the [FOCUS] button.
The Focus adjustment window appears.
Indicates the button operation on the remote control.
Indicates the button to be
pressed.
Symbols Used in This Manual
Meanings of the following symbols used in this manual are as follows:
(SX7 II)
Function or description only applicable to SX7 MarkII.
A precaution about operation or restriction is given here.
An important matter that you should be aware of before operation or a useful tip is provided here.
Downloaded From projector-manual.com Canon Manuals
17
COPYRIGHT NOTICE
Please note that enlarging or reducing the size of an image for commercial purposes or
public presentation may infringe on the legally protected copyright or the copyright holder
of the original material.
About Trademarks
z Microsoft, Windows, Windows XP, Windows Vista and Windows 7 are registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.
z Macintosh and Mac are registered trademarks of Apple Computer, Inc., registered in
the United States and/or other countries.
z Adobe is a registered trademark or trademark of Adobe Systems Incorporated in the
U.S. and other countries.
z The "HD ready" logo is a trademark of EICTA.
z HDMI is a registered trademark or trademark of HDMI Licensing, LLC.
Downloaded From projector-manual.com Canon Manuals
18
Table of contents/Safety Instructions
Before Use
Setting Up the Projector
BEFORE USE
Projecting an Image from the Computer
Projecting an Image from AV Equipment
Useful Functions Available During a Presentation
Setting Up Functions from Menus
Maintenance
Troubleshooting
Appendix
Index
Downloaded From projector-manual.com Canon Manuals
Before Use
Supplied Accessories
Check whether the following accessories are supplied with the projector.
z Remote control
BEFORE USE
z Batteries (type AAA, two)
for remote control
z Power cord (1.8m/5.9')
z Computer connection cable
(DVI/Mini D-sub, 15-pin) (1.8m/5.9')
YH7-2052
z USB cable (1.8m/5.9')
YH7-2054
For Continental
Europe
z Component cable
(RCA/Mini D-sub, 15-pin)
(0.4m/1.3') YH7-2084
For the U.S.A and Canada
z Carrying bag
z Lens cap
z Lens cap strap
z User's Manual (CD-ROM)
z Warranty card
z Important Information
and Quick Start Guide
Downloaded From projector-manual.com Canon Manuals
20
Installing the Lens Cap
As shown in the illustration on the right, let the lens
cap strap through the hole on the lens cap, and then
the lens cap strap insertion hole.
BEFORE USE
z When the projector is not in use, attach the lens
cap to protect the lens from dust and other foreign
objects.
Putting the Projector in the Carrying Bag
Store the projector and the accessories in the carrying bag as shown in the illustration
below.
The carrying bag is intended to protect the surfaces of the projector from dust or
scratches, and is not designed to protect the projector from external shocks.
Align the lens with the dimple
on the cushioning material.
z User's Manual (CD-ROM)
z Important Information
and Quick Start Guide
Cables
Remote control
z Wait until the cooling fan stops before putting the projector in the carrying bag. Do not
put the projector in the carrying bag until the cooling fan stops rotating. The projector
may be damaged due to the heat.
z Attach the lens cap to the lens to protect it and put the projector in the carrying bag.
Replace the adjustable foot to prevent the damage on the projector.
z When carrying the projector with it put in the carrying bag, do not give a shock to it,
drop it, or place anything on it. The projector may be damaged or malfunctioned.
Downloaded From projector-manual.com Canon Manuals
21
Part Names
Main Unit of Projector
(SX7 MarkII is used in the following illustrations)
Front Side
BEFORE USE
Infrared Remote Receiver (P29)
Terminals and
Connectors
Ranging Window
Do not place any obstacle
between the projector and the
Caution screen, as the auto focusing
function may fail to operate correctly.
Be sure to remove the lens cap
during projection. Failure to do
Caution so will result in cap deformation
or fire hazards.
Lens
Adjustable Foot Lock Button (P43)
Lens Cap (P21)
Power Cord Connector (P40)
Anti-theft Lock Hole
An anti-theft wire cable on the market
can be connected.
Rear Side
Top Control (P24, 25, 28)
Do not block the air exhaust.
Failure to do so will result in malCaution functions or fire hazards.
Speaker
Infrared Remote Receiver (P29)
Exhaust Vent
Downloaded From projector-manual.com Canon Manuals
22
Bottom Side
Lens Cap Strap
Insertion Hole
Do not block the air intake. Failure to do so will result in malfuncCaution tions or fire hazards.
Adjustable Foot (P43)
Air Intake Vent
BEFORE USE
Lamp Cover (P123)
Rear Adjustable Foot
(for fine adjustment)
Air Filter
(P121)
Screw Holes for installation of ceiling
mounting bracket (M4 x 6) (P139)
Mounting the Projector on the Ceiling
You can mount the projector on the ceiling.
You need an optional ceiling-mount hanger (part number: RS-CL07) and an optional
ceiling-mount pipe (part number: RS-CL08 or RS-CL09) when appropriate.
Contact the dealer where you purchased the projector for more detailed information.
z Make sure to use the optional ceiling mounting bracket.
z You should never install the ceiling mounting bracket by yourself.
z If you mount the projector on the ceiling, you have to invert the projected image by
selecting [Image flip H/V] from the menu (P97).
Downloaded From projector-manual.com Canon Manuals
23
Buttons on the Remote Control and Top Control
Remote Control
(1)
BEFORE USE
(5)
(2)
(3)
(4)
(6)
(7)
(8)
This projector can be operated using buttons on the remote control or the top control on the main unit.
The remote control allows you to operate
all functions of the projector.
(9)
(10)
(11)
(12)
(14)
(15)
(13)
(16)
(17)
(19)
(20)
(22)
(18)
(21)
(1) Infrared Remote Emitter
Sends a signal to the infrared remote
receiver on the main unit.
(2) POWER button (P40, 60)
Turns the projector on or off.
(3) AUTO SET button (P46, 70)
Performs auto adjustment on focusing, keystone distortion, screen color
correction, and so on (Auto Setup
Function).
(4) IMAGE button (P55)
Switches among image modes
(image qualities).
(5) INPUT button (P48, 50, 70)
Switches among input signals.
(6) AUTO PC button (P54)
Adjusts tracking and so on automatically in accordance with signal from a
computer when ANALOG PC-1 or
ANALOG PC-2 is selected.
(7) FOCUS button (P51)
Adjusts focusing.
(8) ZOOM button (P42)
Adjusts the image size.
(9) OK button (P89)
Determines the item selected from the
menu. Also works as the left button of
a mouse under the USB connection
(P82).
Downloaded From projector-manual.com Canon Manuals
24
Top Control
(7)
(8)
BEFORE USE
(9)
(2)
(3)
(5)
(10) POINTER button (P87)
Selects the upper, lower, left, or right
item in the menu. Also moves the
mouse cursor under the USB connection.
On the top control, the [<] and [>]
buttons also turn the volume up and
down, respectively (P79).
(11) KEYSTONE button (P52, 59)
Corrects keystone distortion. The [D.
image shift adjustment] screen will be
displayed if you select [16:9 D. image
shift] for [Screen aspect].
(12) MENU button (P87)
Displays a menu on the screen.
(13) PAGE button (P80)
Acts as the Page Up and Page Down
keys on the computer keyboard under
the USB connection.
Pressing
scrolls to the previous
page and pressing
scrolls to the
next page.
(14) D.ZOOM button (P81)
Zooms the image in or out digitally.
Pressing
enlarges the image and
pressing
reduces the image.
(15) SPOT button (P83)
Performs the spot light function.
(6)
(11)
(12)
(10)
(16) R-CLICK button (P82)
Acts as the right button of a mouse
under the USB connection.
(17) NO SHOW button (P78)
Switch display/non-display of image.
(18) MUTE button (P79)
Mutes the sound.
(19) VOL button (P79)
Adjusts the sound volume.
(20) FREEZE button (P78)
Freezes the projected image.
(21) P-TIMER button (P80)
Displays the time elapsed since this
button was pressed.
(22) LIGHT button (P29)
Turns on or off the lights of the remote
control buttons.
Downloaded From projector-manual.com Canon Manuals
25
Input Terminals on Main Unit
SX7 MarkII
(1)
(10)
(2)
(3)
BEFORE USE
(4)
(5)
(10)
(9)
(8)
(7)
(6)
SX60
(1)
(10)
(2)
(3)
(10)
(7)
(5)
(8)
(6)
(9)
Downloaded From projector-manual.com Canon Manuals
26
BEFORE USE
(1) Input Terminal-1 (DIGITAL IN/ANALOG IN-1) (P36, 37, 65)
Receives a digital (DIGITAL PC) and analog PC signal (ANALOG PC-1).
Receives a digital content image signal (DIGITAL VIDEO).
(2) Input Terminal-2 (ANALOG IN-2) (P36, 37, 64)
Receives an analog PC signal (ANALOG PC-2).
Receives a component and SCART image signal (COMPONENT/SCART).
(3) Monitor Output Terminal ( ) (P38)
Outputs an analog PC signal to display an image on an external monitor.
(4) AUDIO OUT terminal (SX7 II) (P68)
The audio output terminal to output an audio to an external audio device.
It outputs the audio signal corresponding to the projected image signal.
(5) AUDIO IN terminal (P38, 39)
SX7 II: The audio input terminals corresponding to 3 image input systems.
Each terminal receives the audio signal corresponding to "DIGITAL PC/
ANALOG PC-1", "ANALOG PC-2", and "S-VIDEO or VIDEO" from the left.
The internal speaker outputs the audio signal corresponding to the
selected image signal.
SX60: The input terminal of an audio signal.
The internal speaker outputs the audio signal no matter what the image
signal is inputted.
(6) VIDEO IN terminal (P66)
Receives a composite video signal from an AV equipment.
(7) S-VIDEO IN terminal (P66)
Receives an S-Video signal from an AV equipment.
(8) SERVICE PORT jack
Exclusively used by the service personnel (it is not used normally).
(9) USB terminal (P82)
Connected to the computer with a USB cable when the remote control is used
as the mouse of the computer. (you cannot use this terminal to receive any
video image)
(10) Input Terminal Indicator (P48, 70)
Indicates the input signal status.
Green
: The input signal is confirmed and an image is projected.
Flashing green : The input signal is confirmed but no image is projected.
Off
: An input signal is not confirmed (a cable is not connected).
Downloaded From projector-manual.com Canon Manuals
27
Indicators on the Top Control
Top Control
BEFORE USE
(1)
(2)
(3)
(1) POWER indicator (P40, 60, 111)
Indicates the projector status.
Red:
The projector can be turned on.
Flashing red:
The projector is being turned off (the lamp is being
cooled).
Green:
The projector is on.
Flashing green:
The projector is being turned on.
Blink between red and green: The projector is under the power management
mode.
(2) WARNING lamp (P126)
Flashes red when a problem has been detected on the projector.
(3) LED illumination lamp (P115)
Indicate the projector status with 3 blue LEDs.
Blinking from the left:
The projector is being turning on.
Blinking from the right:
The projector is being turned off.
Middle LED flashing slowly: The image is blackened out (NO SHOW).
Left and right LEDs flashing slowly:
The image is stopped (FREEZE).
Downloaded From projector-manual.com Canon Manuals
28
Preparing the Remote Control
Installing Remote Control Batteries
1
2
Insert batteries.
Insert new two AAA-size
batteries in the compartment with the + and poles positioned correctly.
3
Replace the compartment lid.
BEFORE USE
Open the battery compartment lid.
Slide the lid with it
pressed down.
z You can check the batteries of the remote control by pressing the [LIGHT] button.
If all buttons on the remote control do not light when the [LIGHT] button is pressed, or buttons are inoperative when you attempt to operate the projector, replace with new batteries.
z It is recommended to check the batteries before a presentation.
Remote Control Operating Range
Point the remote control to the infrared
remote receiver on the front or rear of the
projector whenever pressing any button.
z Use the remote control within a distance
of approximately 5 m (16.4') from the projector.
z Use the remote control within an angle of
30° in any direction from directly in front
of the infrared remote receiver.
30°
5m
(16.4')
30°
5m
(16.4')
30°
30°
The remote control may be inoperative if:
z There is an obstacle between the remote control and main unit.
z The infrared remote receiver on the main unit is exposed to direct sunlight or strong light of
lighting equipment.
z The remote control uses infrared light.
z When you use two projectors at the same time, you can change the channel settings to prevent the two remote controls from interfering with each other (P115).
Downloaded From projector-manual.com Canon Manuals
29
Downloaded From projector-manual.com Canon Manuals
Table of contents/Safety Instructions
Before Use
Setting Up the Projector
SETTING UP THE
PROJECTOR
Projecting an Image from the Computer
Projecting an Image from AV Equipment
Useful Functions Available During a Presentation
Setting Up Functions from Menus
Maintenance
Troubleshooting
Appendix
Index
Downloaded From projector-manual.com Canon Manuals
Setting Up the Projector
Determining the Distance to the Screen
The projected image size is determined by the distance between the projector lens and the
screen. Select the place where the desired image size is obtained according to the illustration shown below.
8.9 m (29.2')
300"
5.9 m (19.4')
SETTING UP THE PROJECTOR
4.5 m (14.8')
Zoom (max.)
200"
182"
2.4 m (7.9')
150"
1.2 m (3.9')
Zoom (min.)
H1
120"
80"
90"
48"
40"
H2
H1:H2=9:1
Screen size
(W x H) cm
Zoom
Projection (max)
distance Zoom
(min)
Optical axis when image is projected
at right angle to the screen.
40"
81 x 61
Screen
60"
80"
100"
150"
182"
200"
250"
300"
122 x 91 163 x 122 203 x 152 305 x 229 370 x 277 406 x 305 508 x 381 610 x 457
1.2 m
(3.9')
1.8 m
(5.9')
2.4 m
(7.9')
3.0 m
(9.8')
4.5 m
(14.8')
5.4 m
(17.7')
5.9 m
(19.4')
7.4 m
(24.2')
8.9 m
(29.2')
2.0 m
(6.6')
2.9 m
(9.6')
3.9 m
(12.9')
4.9 m
(16.1')
7.4 m
(24.2')
9.0 m
(29.5')
–
–
–
H1
55 cm
(1.8')
82 cm
(2.7')
110 cm
(3.6')
137 cm
(4.5')
206 cm
(6.8')
250 cm
(8.2')
274 cm
(9.0')
343 cm
(11.3')
411 cm
(13.5')
H2
6 cm
(0.2')
9 cm
(0.3')
12 cm
(0.4')
15 cm
(0.5')
23 cm
(0.8')
28 cm
(0.9')
30 cm
(1.0')
38 cm
(1.2')
46 cm
(1.5')
H1 and H2: The height of the screen from the intersection of optical axis and screen surface when an
image is projected at right angle to the screen.
z Install the projector at the position where the projection distance is between approximately 1.2 m (3.9') to 9 m (29.5'). If the installation position is too close or too far, the
image is out of focus or the screen becomes dark, respectively.
z The sizes in the above table have been obtained assuming that the aspect ratio is 4:3.
They may vary from the actual sizes depending on the type of the projected image.
z Select the appropriate setting for [Screen aspect] with respect to the your screen (4:3
or 16:9).
Refer to pages 59, 74, and 101 for more detailed information on [Screen aspect].
z For the relationship between the screen size and projection distance, see the table on page
133.
z You can also adjust the image size with the zoom function (P42).
Downloaded From projector-manual.com Canon Manuals
32
Determining the Installation Position
Placing in Front of the Screen
Place the projector perpendicular to the screen
as far as possible.
Screen
z A slight error in the projection angle can be
corrected using the [KEYSTONE] button
(P52).
SETTING UP THE PROJECTOR
Optical axis
Placing on a Level Place
Place the projector on a level place as far as possible.
z A slight tilt can be corrected using the rear
adjustable foot. (P43)
z Make sure that the installation position is
free from any obstacle that may block the
exhaust vent (fan) on the right side of the
projector and the air intake vent on the bottom of the projector.
z The screen must not be exposed to direct
sunlight or light from lighting equipment. In a
bright room, it is recommended to limit
ambient lighting in order to improve the
image quality.
Ceiling Mounting or Rear Projection
You can mount the projector on the ceiling (Ceiling mounted) with it turned up side
down or place it behind the screen (Rear) if you use a translucent screen. For ceiling
mounting or rear projection, you have to invert the projected image. (P97).
Ceiling Mounting
Downloaded From projector-manual.com Canon Manuals
Rear Projection
33
Downloaded From projector-manual.com Canon Manuals
Table of contents/Safety Instructions
Before Use
Setting Up the Projector
PROJECTING AN
IMAGE FROM
THE COMPUTER
Projecting an Image from the Computer
Projecting an Image from AV Equipment
Useful Functions Available During a Presentation
Setting Up Functions from Menus
Maintenance
Troubleshooting
Appendix
Index
Downloaded From projector-manual.com Canon Manuals
Projecting an Image from the Computer
Connecting the Projector to the Computer
Connect the projector to the computer.
Connecting to Video Terminals
Supplied computer connection cable
VGA cable
To monitor output terminal
(mini D-sub 15-pin terminal)
To monitor output terminal
(mini D-sub 15-pin terminal)
PROJECTING AN IMAGE FROM THE COMPUTER
Computer
Computer
Supplied computer
connection cable
Input Terminal-1
(ANALOG IN-1)
Projector
Input Signal: Select [ANALOG PC-1] (P48)
Commercial VGA cable
Input Terminal-2
(ANALOG IN-2)
Projector
Input Signal: Select [ANALOG PC-2] (P50)
z To ensure projection of high-resolution high-quality images, it is recommended to use highperformance cables.
z An adapter may be required depending on the shape of the connector on the computer.
For more detailed information, refer to your computers instruction manual.
Downloaded From projector-manual.com Canon Manuals
36
z Before connecting cables, turn off both the projector and computer.
z It may project an image inappropriately when projecting the digital PC signal in 1280 x 1024
or 1400 x 1050 depending on the type of computer or DVI cable.
z The USB terminal is used to use the remote control as the computer mouse. An image cannot be projected simply by connecting the USB cable.
DVI cable
5-BNC cable
To monitor output terminal
(DVI terminal)
To monitor output terminal
(5-BNC output terminal)
Computer
PROJECTING AN IMAGE FROM THE COMPUTER
Computer
Extension cable
Optional DVI digital cable
[LV-CA29]
Input Terminal-1
(DIGITAL IN)
Projector
Input Signal: Select [DIGITAL PC] (P48)
Downloaded From projector-manual.com Canon Manuals
Commercial 5-BNC
cable (for 5-BNC/
mini D-Sub 15-pin)
Input Terminal-2
(ANALOG IN-2)
Commercial 5-BNC
extension cable
Projector
Input Signal: Select [ANALOG PC-2] (P50)
37
Connecting to an External Monitor
You can display an image from the projector to an external monitor.
Connecting to AUDIO IN Terminals (SX7 II)
Connect an audio cable to the AUDIO IN terminal corresponding to the input image signal if you want to use the projector's speaker.
Audio cable
VGA cable
AUDIO OUT terminal
Computer
Projector
PROJECTING AN IMAGE FROM THE COMPUTER
To monitor output terminal
(mini D-sub 15-pin terminal)
Commercial Audio cable
You can input an audio signal
corresponding to 3 image
input systems.
Connect to the AUDIO IN terminal corresponding to the
type of the input image signal.
for DEGITAL IN/ANALOG IN-1
Commercial VGA cable
for ANALOG IN-2
External monitor
AUDIO IN terminal
Projector
SX7 MarkII
Image input terminal
(mini D-sub 15-pin terminal)
z You can connect one external monitor.
The multi-monitor display is not supported.
z The projected image is displayed on
the external monitor.
z You cannot output the input signal to
the external monitor if it is DIGITAL
PC.
Downloaded From projector-manual.com Canon Manuals
38
z The speaker outputs the audio signal
corresponding to the selected image
signal.
z Use an audio cable without a built-in
resistor. Using an audio cable with a
built-in resistor turns down the sound.
z Connect the audio cable between the
AUDIO OUT terminal and an external
audio-visual equipment if you want to
output the audio signal to the audiovisual equipment (P68).
z The built-in speaker is monaural.
Connecting to AUDIO IN Terminals (SX60)
Connect the audio cable to the AUDIO IN
terminal if you want to use the projectors
speaker.
Audio cable
AUDIO OUT terminal
Computer
PROJECTING AN IMAGE FROM THE COMPUTER
Commercial Audio cable
Projector
AUDIO IN terminal
SX60
z Use an audio cable without a built-in
resistor. Using an audio cable with a
built-in resistor turns down the sound.
z The built-in speaker is monaural.
z The speaker plays the sound from the
equipment which the audio cable is
connected to regardless of the image
input signal.
Downloaded From projector-manual.com Canon Manuals
39
Starting Projection
Connect the power cord and turn on the projector to start the projection.
z Once the projector is turned off, it cannot be turned on for a while. Wait until the lamp is
cooled down and the [POWER] indicator lights in red.
Connect the Ground Terminal
Caution
Connect the ground terminal on the power plug to ground. Otherwise, the operating
computer may suffer electromagnetic radiation problems and poor reception by TV and
radio.
Unplug the Power Cord When the Projector is Not in Use
PROJECTING AN IMAGE FROM THE COMPUTER
The projector constantly consumes approximately 7W power even when it is turned off.
To ensure safety, malfunction prevention, and power saving, remove the power plug
from the AC outlet when the projector is not used for an extended period of time.
1
Connect the power cord.
Fully insert the power cord plug into the socket.
The [POWER] indicator flashes red.
2
Remove the lens cap and press the [POWER] button.
The [POWER] indicator flashes green, and
then lights in green.
Downloaded From projector-manual.com Canon Manuals
40
The countdown window is displayed for approximately 20 seconds, and then the guiding message for the auto setup function appears.
Adjust the focus by performing the auto setup or the focus adjustment if you cannot
read the message due to out of focus. (P46, 51)
The LED illumination lamp blinks blue until the projection is started.
To project an image immediately, press the [OK] button.
z Enter a password if the Password input screen appears (P116, 117).
z You can turn on the projector by connecting the power cord without pressing the [POWER]
button (direct power on) (P112).
z You can display a specified Logo on the countdown screen (P100).
z You can specify whether to enable or disable the LED illumination lamp (P115).
z You can skip the countdown window (P100).
PROJECTING AN IMAGE FROM THE COMPUTER
Selecting a Language
A window appears when the projector is turned on for the first time. You can select a
language to be used by the projector for displaying menus and so on in the window.
Select your language as shown below.
Select a language with the POINTER buttons and press the [OK] button.
An item highlighted in orange will be selected.
z Adjust the focus by performing the focus adjustment if it is out of focus (P51).
z You can change the language from the menu at a later time (P113).
Downloaded From projector-manual.com Canon Manuals
41
Adjusting the Image
Adjusting the Image Size (ZOOM)
Adjust the image size in accordance with the screen.
Press the [ZOOM] button.
The Zoom adjustment window appears.
2
Adjust the image size.
Zoom in:
Press [ ] for rough adjustment.
Press [>] for fine adjustment.
<
Zoom out:
Press [ ] for rough adjustment.
Press [<] for fine adjustment.
<
PROJECTING AN IMAGE FROM THE COMPUTER
1
3
Press the [OK] button.
z Change the projector installation position if your desired image size is too large or too small
to adjust with the zoom function (P32).
Downloaded From projector-manual.com Canon Manuals
42
Adjusting the Projection Angle
You can adjust the projection angle with the adjustable foot.
1
Lift the front side of the projector and push the
adjusting foot lock button.
The adjustable foot extends.
2
Adjust the projection angle while pushing the
adjustable foot lock button, and then release
the lock button.
The adjustable feet is fixed.
PROJECTING AN IMAGE FROM THE COMPUTER
z With the adjustable foot, the projection angle
can be adjusted up to 10 degrees.
z If the projector is tilting in the lateral direction,
use the rear adjustable feet on both sides to
adjust its angle. You can adjust up to 10mm
with one foot.
If Keystone Distortion is Too Large
Extending the adjustable foot too far causes keystone distortion. If the distortion is too
large, adjust the height of the projector with a pedestal.
The keystone distortion can be corrected with the Auto keystone function or by pressing
the [KEYSTONE] button. (P46, 52, 70)
Keystone Distortion
Pedestal
Downloaded From projector-manual.com Canon Manuals
43
Preparing the Computer
Determining the Output Resolution of the Computer
To make the most of the display performance of this projector, set output signal resolution
of the computer to an optimum value.
PROJECTING AN IMAGE FROM THE COMPUTER
Windows 7
1. Open the [Control Panel] from the start
menu, then select [Appearance and Personalization] – [Adjust screen resolution] in
the [Control Panel Home].
2. Click the [Resolution] pull-down menu and
move the slider to select "1400 x 1050". If
this resolution is not available, select the
highest resolution under 1400 x 1050.
3. Click the [OK] button.
Windows Vista
1. Open the [Control Panel] from the start
menu, then select [Appearance and Personalization] – [Adjust screen resolution] in
the [Control Panel Home].
2. Select "1400 x 1050 pixels" or a resolution
closest to the output signal resolution of the
computer.
3. Click the [OK] button.
Windows XP
1. Right-click on the desktop background and
select [Properties] to open the [Display
Properties].
2. Click the [Settings] tab, and under [Screen
Resolution], select "1400 x 1050 pixels" or a
resolution closest to the output signal resolution of the computer.
3. Click the [OK] button.
Downloaded From projector-manual.com Canon Manuals
44
Macintosh OSX
1. Open the Apple Menu and select [System
Environment Setting].
2. In the System Environment Setting window, click the [Displays] icon to display
the Display window.
3. Select the [Display] tab and select "1400 x
1050" or a resolution closest to the output
signal resolution of the computer from the
[Resolution] list.
4. Close [System Environment Setting] window.
Projecting the Image from the Notebook Computer
You can turn on the external monitor output via keyboard operation.
To turn on the external monitor output, press an icon for an external monitor or a function
key ([F1] to [F12]) while holding [Fn] key down.
While holding
key
Press a key such as
or
z The function keys you use and the method used to turn on the external monitor output vary
depending on the model. For details, see the instructions of your notebook computer.
Downloaded From projector-manual.com Canon Manuals
45
PROJECTING AN IMAGE FROM THE COMPUTER
For SX7 MarkII/SX60
z If the display resolution of the computer is set to SXGA (1280 by 1024 dots) or WXGA (1280
by 768 dots), it is recommended to select [True size] as the screen mode (P90).
Performing the Auto Setup
With the auto setup function, the following set of adjustments is performed automatically
when projecting an image from a computer. You can start the projection only with this operation if the input signal has been appropriately selected.
Auto focus
Adjusts the focusing automatically.
Auto keystone
Corrects the keystone distortion (in the vertical direction) automatically.
PROJECTING AN IMAGE FROM THE COMPUTER
Auto input
Sets the image input signal automatically.
Auto screen color*
Performs the screen color correction (white balance adjustment) automatically.
*: This is not enabled at the factory.
z Among 4 functions above, the function that has been enabled in the menu is performed
during the auto setup. "Auto focus", "Auto keystone", and "Auto input" are enabled in the factory.
z You can manually set or adjust each function. You can set or adjust a specific function independently if you press the [AUTO SET] button during the manual adjustment.
z Select [Greenboard] from [Screen color] when using a greenboard (dark green) as a screen
(P98).
z The auto focusing and the screen color correction may not be performed properly depending on the brightness of the room or the condition of the screen. Adjust the image manually
if such is the case.
z If you select [16:9] for [Screen aspect], [Auto screen color] may not correct the screen color
properly. If such is the case, correct it manually.
z If you select [16:9 D. image shift] for [Screen aspect], the auto setup function will be disabled.
z If you project an image straight up or down, [Auto focus] and [Auto keystone] will be disabled.
1
Select an input signal.
Select an appropriate input signal by following the steps in the "Selecting an Input Signal" section at the page 48 if you change the input signal due to changing the connection to the computer or so.
Skip this step if you have not changed the input signal since the last projection.
Downloaded From projector-manual.com Canon Manuals
46
Press the [AUTO SET] button.
The Auto setup window appears.
3
Press the [AUTO SET] button again.
One or more functions highlighted in black are performed automatically.
PROJECTING AN IMAGE FROM THE COMPUTER
2
z You can perform this step by selecting [OK] with the [<] button, and then pressing the [OK]
button.
Downloaded From projector-manual.com Canon Manuals
47
Selecting an Input Signal
You can select an input signal type.
Select an input signal from the followings:
ANALOG PC-1 : Analog signal Connecting with a DVI/Mini D-sub 15-pin cable
(supplied cable)
DIGITAL PC
: Digital signal Connecting with a DVI digital cable
ANALOG PC-2 : Analog signal Connecting with a VGA cable or 5-BNC cable
Select an appropriate input signal before starting the auto setup function by following the
steps below if you change the input signal due to changing the connection to the computer
or so.
PROJECTING AN IMAGE FROM THE COMPUTER
z An LED for a terminal flashes in green if a cable is connected and an input signal is confirmed. An LED for a terminal turns on if the projected image is obtained through the terminal (P26, 27).
z Connecting a DVI cable to Input Terminal-1, select the appropriate input signal with the
[INPUT] button in accordance with the setting on the computer (digital signal/analog signal).
„ Selecting [ANALOG PC-1] or [DIGITAL PC]
1
Press the [INPUT] button.
The [INPUT] window appears.
2
Select [ANALOG PC-1] or [DIGITAL PC] in the menu with the [INPUT] button.
The selection is toggled through available input signal types from above.
<
Downloaded From projector-manual.com Canon Manuals
48
<
z You can select any input signal type from all options through the [ ] / [ ] button.
4
Press the [OK] button.
<
If the target input signal is unavailable from the list at the left, press the [>] button, and
then press the [ ] / [ ] button to select the target input signal from the list at the right.
<
3
PROJECTING AN IMAGE FROM THE COMPUTER
Downloaded From projector-manual.com Canon Manuals
49
„ Selecting ANALOG PC-2
z Select [ANALOG PC-2] for Input Terminal-2.
Press the [INPUT] button.
The [INPUT] window appears.
2
Select the second top item in the menu with the [INPUT] button.
The selection is toggled through available input signals from above.
<
z You can select any input signal type from all options through the [ ] / [ ] button.
<
3
If the ANALOG PC-2 is unavailable from the list at the left, press [>], and then press [ ]
/ [ ] to select the ANALOG PC-2 from the list at the right.
4
Press the [OK] button.
<
PROJECTING AN IMAGE FROM THE COMPUTER
1
<
Downloaded From projector-manual.com Canon Manuals
50
Adjusting the Focus
You can adjust the focus.
Follow the steps below to adjust the focus manually if the Auto setup function (Auto focus)
does not adjust the focus appropriately.
Press the [FOCUS] button.
The Focus adjustment window appears.
2
Press the POINTER buttons to adjust the focus.
PROJECTING AN IMAGE FROM THE COMPUTER
1
<
<
Rough adjustment: [ ] [ ]
Fine adjustment : [<] [>]
z You can activate the Auto focus function if you press the [AUTO SET] button now.
However, if you select [16:9 D. image shift] for [Screen aspect], the auto focus function
will be disabled.
3
Press the [OK] button.
z The projected image may be out of focus if the projection distance is beyond the range of
1.2 m (3.9') to 9 m (29.5'). Move the projector installation position if such is the case (P32).
Downloaded From projector-manual.com Canon Manuals
51
Adjusting Keystone Distortion
The Auto setup function (Auto keystone) automatically adjusts the keystone distortion in a
longitudinal direction. Follow the steps below if the function does not adjust the distortion
appropriately or you want to adjust the keystone distortion in a horizontal direction.
Press the [KEYSTONE] button.
The [Keystone adjustment] windows appears.
2
Press the POINTER buttons to adjust the focus.
To reduce the length of the
lower edge, press [ ].
To reduce the length of the left
edge, press [<].
To reduce the length of the
right edge, press [>].
<
To reduce the length of the
upper edge, press [ ].
<
PROJECTING AN IMAGE FROM THE COMPUTER
1
z You can activate the Auto keystone function if you press the [AUTO SET] button now.
Downloaded From projector-manual.com Canon Manuals
52
3
Press the [OK] button.
Downloaded From projector-manual.com Canon Manuals
PROJECTING AN IMAGE FROM THE COMPUTER
z The result of keystone adjustment is memorized. If you place the projector at the same position, the keystone adjustment is not necessary.
z When the Keystone adjustment is selected, signals are processed digitally. The image may
look different from the original one.
z The aspect ratio of the image may change after the keystone adjustment.
z Keystone can be adjusted vertically and horizontally within the range of +/-20 degrees. The
amount of adjustment may be less than +/-20 degrees depending on the combination of the
amount of optical zooming, input signal type, and adjustment direction (vertical or horizontal).
z If the keystone distortion is too large to adjust, move the projector installation position (P32).
z To reset the keystone adjustment to 0, press the [KEYSTONE] button again to display the
[Keystone reset] window. On the window, select [OK] with the [<] button, and then press the
[OK] button.
z If you select [16:9 D. image shift] for [Screen aspect], the keystone adjustment will be disabled. Project the image at right angle to the screen.
53
Setting Up the Computer Screen Automatically (AUTO PC)
This projector automatically makes optimum settings for the total number of dots and tracking depending on a signal type (SXGA+, XGA, etc.).
The auto PC adjustment function does not need to be performed if the projector is projecting an image properly with [Auto Setup].
You can use this function if the input signal is [ANALOG PC-1] or [ANALOG PC-2].
1
Press the [AUTO PC] button.
The auto PC adjustment function is activated and the projected image is optimized.
PROJECTING AN IMAGE FROM THE COMPUTER
z For some computers, the auto PC adjustment function does not optimize the projected
image. If such is the case, you need to make settings (input signal select, total dots, tracking, horizontal/vertical positions, horizontal/vertical pixels, etc.) for the input signal (P91, 9395).
z The previous signal type ([ANALOG PC-1] or [ANALOG PC-2]) is recorded. If you connect
the projector to the same computer, you can project the image with the same settings as
before simply by selecting the input signal.
Downloaded From projector-manual.com Canon Manuals
54
Selecting an Image Mode (IMAGE)
You can select an image mode depending on the projecting image. You can also adjust the
image quality (sharpness, gamma, color correction, etc.) as you like.
1
Press the [IMAGE] button.
(SX7 MarkII)
[Standard]
Select this to project an image with near-original quality and a
high regard for reproduction of white. It is also suited to project
moving pictures such as a TV program or a DVD movie in a
bright room.
[Presentation] Select this to project an image with quality suited for the presentation. It also suited to project moving pictures with a high
regard for the brightness.
[Movie]*1
Select this to project moving pictures of all kinds. Its brightness is suited to easily enjoy the atmosphere of a movie theater in a dim room.
[Photo]*2
If you select [Photo] for [Image mode], make sure to set
[Ambient light] in the [Image adjustment] as well.
You can correct an image according to the ambient light
based on [sRGB] in [Image mode] and project the image with
higher tone on the screen by setting [Ambient light]. It is suited
to project an ornamental photo, etc. under an ambient light.
[AdobeRGB]
Select this if you want to project an image in the display mode
conforming to Adobe RGB color space. You can project an
image with more accurate color reproduction since It has
wider color gamut than sRGB.
[sRGB]
Select this if you want to project an image in the display mode
conforming to Windows standard color space. It is suited to
project an image shot by an sRGB-compatible digital camera.
[Home Cinema] Select this to project a movie with quality suited to seriously
enjoy the atmosphere of a movie theater in a dark room.
*1 It is available if the input signal is [DIGITAL VIDEO], [COMPONENT], [VIDEO] or [S-VIDEO].
*2 It is available if the input signal is [ANALOG PC-1], [ANALOG PC-2], or [DIGITAL PC].
Downloaded From projector-manual.com Canon Manuals
55
PROJECTING AN IMAGE FROM THE COMPUTER
The Image mode window appears. The selection is toggled among following modes
by pressing the button.
SX7 MarkII
Standard
Presentation
Movie
Photo
AdobeRGB
sRGB
SX60
Standard
Presentation
Movie
Home Cinema
sRGB
PROJECTING AN IMAGE FROM THE COMPUTER
z You can adjust the followings for each image mode. For detailed information on the procedures, refer to "Image Adjustment Menu" (P102 to 110).
- Brightness Adjust this when the image is too bright or dark.
- Contrast
Adjust this to decrease or increase contrast of the entire image.
- Sharpness Adjust this to soften or sharpen an image.
- Gamma
Adjust this when light or dark portions of an image are obscure.
- Color adjustment
Adjust this to adjust the color level and balance.
- Advanced adjustment
Adjust this when color tones are different from those of the original image.
z The results of adjustments are saved for each input signal. Once you save them, you can
project images with the same settings.
z You can set an image mode from the menu. Refer to [Image mode] section in the menu
(P102)
Downloaded From projector-manual.com Canon Manuals
56
Selecting a Screen Mode (Aspect)
You can select one of the following screen modes depending on the aspect ratio or display
resolution of your computer.
z You can specify the aspect ratio from the menu. Refer to [Aspect] in the menu (P90).
z The available screen mode will be different depending on the setting of [Screen
aspect]. Refer to the section [Screen aspect] (P59).
„ Full screen
„ 4:3
Select this to display a computer screen with aspect ratio of
4:3 on the 16:9 screen if you have selected [16:9 D. image
shift] for [Screen aspect].
„ Auto
Select this to project a wide screen or computer screen with
aspect ratio of 5:4 (SXGA).
Since the image is projected with it fitted to either the width or
length of the computer screen, it does not display the top and
bottom portions or the leftmost and rightmost portions of the
image.
„ Wide
Select this to project a computer screen with aspect ratio of
16:9.
Since the image is projected with it fitted to the width of the
computer screen, it blackens the top and bottom portions of
the screen.
Downloaded From projector-manual.com Canon Manuals
57
PROJECTING AN IMAGE FROM THE COMPUTER
Select this to project a computer screen with aspect ratio of
4:3 (SXGA+ [1400 by 1050 dots] or XGA [1024 by 768 dots]).
If you select this mode to project the computer screen with
aspect ratio of 5:4 (SXGA [1280 by 1024 dots]), it is compressed vertically or horizontally.
Select this mode under normal conditions.
[Full screen] will be disappeared from the menu screen if you
select [16:9] or [16:9 D. image shift] for [Screen aspect].
„ True size
Select this if you want to project a computer screen in its original size.
A clear image can be obtained because of no image processing.
PROJECTING AN IMAGE FROM THE COMPUTER
z If the display resolution of the computer is higher than 1400 by 1050 dots, select a lower
resolution before starting projection.
z The upper, lower, left, and/or right portions of a projected image may be missing depending
on the Aspect setting.
Downloaded From projector-manual.com Canon Manuals
58
Selecting Aspect Ratio of the Projecting Image
(Screen aspect)
You can select among three aspect ratios of the projecting image according to the aspect
ratio of the projected screen.
You can project an image on the whole screen by setting [Screen aspect].
z You can set [Screen aspect] from menu. Refer to the section [Screen aspect] on the
menu for details. (P101)
„ 4:3
Select this when you use a screen with aspect ratio of 4:3.
PROJECTING AN IMAGE FROM THE COMPUTER
„ 16:9
Select this when you use a screen with aspect ratio of 16:9.
z [Wide] is automatically selected for [Aspect].
z [Auto screen color] may not correct the screen color properly. If such is the case, correct it
manually. (P98)
„ 16:9 D. image shift
[ ]: Moves down the image.
<
<
[ ]: Moves up the image.
Perform the following steps to shift the projected image.
2
Press [ ] / [ ] on the top control or remote control to adjust its vertical position.
3
Press the [OK] button.
<
Press the [KEYSTONE] button on the top control or remote control to open the [D.
image shift adjustment] screen.
<
1
Select [4:3] from the [Aspect] menu if you want to project a video image with aspect ratio of
4:3 in this mode. (P57)
z Keystone adjustment will be disabled. Project the image at right angle to the screen.
z [Auto focus], [Auto keystone], and [Auto screen color] are disabled in the [Auto setup] function.
z You cannot register the image for [Projector on], [No signal screen], or [NO SHOW].
z [SPOT] will be disabled.
Downloaded From projector-manual.com Canon Manuals
59
Turning Off the Projector
z You may shorten the lamp life if turning off the projector while its lamp is still in an unstable
state shortly after turning on the projector. Wait at least 5 minutes before turning off the projector.
z Wait at least 5 minutes before turning on the projector when you turn off the projector. It may
shorten the lamp life if you turn on the projector immediately after turning it off.
z Using the projector for a long time may shorten the life of the lamp and internal optical components.
PROJECTING AN IMAGE FROM THE COMPUTER
z When the projector is turned off, it starts cooling the lamp. You cannot turn it on during the
process.
1
Press the [POWER] button.
A confirmation message appears on the screen.
To continue projection, wait until the confirmation message disappears (approximately
4 seconds) or press a button other than the [POWER] button.
2
Press the [POWER] button again while the confirmation message is displayed.
The lamp goes off, the [POWER] indicator starts flashing in red, and it starts cooling
the lamp.
3
Remove the power cord from the AC outlet.
It continues to cool down the lamp even after removing the power cord.
Downloaded From projector-manual.com Canon Manuals
60
z Wait until the cooling fan stops before putting the projector in the carrying bag. Do not put
the projector in the carrying bag until the cooling fan stops rotating. The projector may be
damaged due to the heat.
z Attach the lens cap to the lens to protect it and put the projector in the carrying bag.
Replace the adjustable foot to prevent the damage on the projector.
z You can carry the projector immediately after the use ("Off & Go" function).
z You can turn off the projector by disconnecting the power cord without pressing the
[POWER] button.
z The LED illumination lamp turns on to indicate the lamp is being cooled when the power
cord is connected.
You can use the power management function that turns off the lamp if the projector
receives no signal input for a while.
If you enable the power management mode, the projector displays a countdown timer if the
projector is receiving no signal input and is not operated for 30 seconds, and approximately 5 minutes later the lamp is turned off and the projector goes into the power management mode.
You can select one of the following power management modes from the menu (P111).
Standby mode
Select this mode if you want to start projection soon.
In the standby mode, the lamp is turned off and cooled down. When the lamp has been
cooled down, the [POWER] indicator starts flashing in red and green to indicate it is
standby. It will start projection if the input signal is inputted or any button on the top control
or remote control is pressed.
Exit mode
Select this mode to turn off the projector automatically.
In the exit mode, the lamp is turned off and cooled down. When the lamp has been cooled
down, the [POWER] indicator stops flashing in red and stays on and the power is turned
off.
z The projector becomes inoperative when the lamp is being cooled in a power management
mode.
Downloaded From projector-manual.com Canon Manuals
61
PROJECTING AN IMAGE FROM THE COMPUTER
Setting Up the Power Management Function
Downloaded From projector-manual.com Canon Manuals
Table of contents/Safety Instructions
Before Use
Setting Up the Projector
PROJECTING AN
IMAGE FROM
AV EQUIPMENT
Projecting an Image from the Computer
Projecting an Image from AV Equipment
Useful Functions Available During a Presentation
Setting Up Functions from Menus
Maintenance
Troubleshooting
Appendix
Index
Downloaded From projector-manual.com Canon Manuals
Projecting an Image from AV Equipment
Connecting the Projector to an AV Equipment
Connect the projector and AV equipment.
Connecting to Video Terminals
Supplied component cable
Connecting to the RCA
component terminal
Connecting to the D terminal
AV equipment
Video output terminal
(RCA component terminal)
PROJECTING AN IMAGE FROM AV EQUIPMENT
Commercial
component cable
(RCA x 3)
(D terminal)
Connect the RCA
cables according
to color code.
z Green (Y)
z Blue (Cb/Pb)
z Red (Cr/Pr)
Commercial
component cable
(D terminal/RCA x 3)
Supplied
component cable
(RCA/Mini D-sub
15-pin)
Supplied
component cable
(RCA/Mini D-sub
15-pin)
Projector
Component input terminal
(ANALOG IN-2)
INPUT Signal: [COMPONENT] is selected automatically
z Before connecting cables, turn off both the projector and AV equipment.
z The above illustrations are just examples. For more detailed information, refer to the manual
for the connecting AV equipment.
About the Component Cable
The projector cannot be connected to an AV equipment only with the supplied component
cable (RCA/Mini D-sub 15-pin). Please purchase either of the following cables according to the
type of the terminal on the AV equipment:
z RCA terminal: RCA x 3/RCA x 3 cable
z D-terminal: D-terminal/RCA x 3 cable
Downloaded From projector-manual.com Canon Manuals
64
SCART cable
Digital cable
You can project digital content via the HDMI or DVI
terminal.
(SCART terminal)
AV equipment
AV equipment
Digital video
output
terminal
(HDMI terminal)
(DVI terminal)
Commercial HDMI adapter cable
Commercial DVI cable
Input Terminal-2
(ANALOG IN-2)
Projector
INPUT Signal: Select [SCART] (P72)
Projector
Input Terminal-1
(DIGITAL IN)
INPUT Signal: Select [DIGITAL VIDEO] (P71)
z Set the input signal as [COMPONENT] by referring to "Projecting an Image from the Computer" and "5-BNC cable" if you want to connect the projector to an AV equipment using a 5BNC extension cable via an video control apparatus in a hall or so (P37).
Downloaded From projector-manual.com Canon Manuals
65
PROJECTING AN IMAGE FROM AV EQUIPMENT
LV-CA31 cable
S-VIDEO cable
Video cable
Video output terminal
(VIDEO OUT terminal)
S-VIDEO output terminal
(S-VIDEO OUT terminal)
AV equipment
AV equipment
Commercial S-VIDEO video cable
Commercial Video cable
PROJECTING AN IMAGE FROM AV EQUIPMENT
Projector
Projector
S-VIDEO input
terminal
(S-VIDEO IN)
Video input
terminal
(VIDEO IN)
SX7 MarkII
SX7 MarkII
SX60
SX60
INPUT Signal: [S-VIDEO] is selected automatically
INPUT Signal: [VIDEO] is selected automatically
z Connect an audio cable if you want to use the projector's speaker.
(SX7 II: P67, SX60: P39)
Downloaded From projector-manual.com Canon Manuals
66
Connecting to AUDIO IN Terminals (SX7 II)
Connect an audio cable to the AUDIO IN terminal corresponding to the input image signal
if you want to use the projector’s speaker.
Audio cable
AV equipment
AUDIO OUT terminal
(RCA terminal)
(Stereo mini jack)
PROJECTING AN IMAGE FROM AV EQUIPMENT
Commercial audio cable
You can input an audio signal
corresponding to 3 image
input systems.
Connect to the AUDIO IN terminal corresponding to the
type of the input image signal.
(RCA/Stereo
mini jack)
(Stereo mini jack)
for DEGITAL IN/ANALOG IN-1
for ANALOG IN-2
for VIDEO IN/S-VIDEO IN
Audio input terminal
(AUDIO IN)
Projector
SX7 MarkII
z The speaker outputs the audio signal corresponding to the selected image signal.
z Use an audio cable without a built-in resistor. Using an audio cable with a built-in resistor
turns down the sound.
z Connect the audio cable between the AUDIO OUT terminal and an external audio-visual
equipment if you want to output the audio signal to the audio-visual equipment (P68).
z The built-in speaker is monaural.
Downloaded From projector-manual.com Canon Manuals
67
Connecting to AUDIO OUT Terminals (SX7 II)
Connect the audio cable between the
AUDIO OUT terminal and an external audiovisual equipment if you want to output the
audio signal to the audio-visual equipment.
Audio cable
AV equipment
AUDIO IN terminal
(RCA terminal)
(Stereo mini jack)
PROJECTING AN IMAGE FROM AV EQUIPMENT
Commercial audio cable
(RCA/Stereo
mini jack)
The audio-visual
equipment outputs
the audio signal
corresponding to
the selected image
signal.
(Stereo mini jack)
Audio output terminal
(AUDIO OUT)
Projector
SX7 MarkII
z Use an audio cable without a built-in resistor. Using an audio cable with a built-in resistor
turns down the sound.
z You can adjust the volume level of the audio signal to the audio-visual equipment with the
remote controller or the buttons on the top control of the projector.
z The internal speaker is disabled if you input the audio cable to the AUDIO OUT terminal.
z If you connect the projector directly to a speaker, make sure to use the amplified speaker.
Downloaded From projector-manual.com Canon Manuals
68
Projecting a Video Image from an AV Equipment
You can project a video image with the steps similar to those for projecting an image from a
computer.
This section provides information specific to the projection from an AV equipment.
For more detailed information for each step, refer to the corresponding page.
1
Turn on the projector.
P40*
z Connect the power cord and turn on the projector.
z Adjust the height of the projecting image.
P40
P43
z Select a display language for the first time.
P41
z Adjust the focus by performing the auto setup or the focus adjustment if you cannot read the message due to out of focus.
PROJECTING AN IMAGE FROM AV EQUIPMENT
2
P46, 51
Prepare the AV equipment.
z Turn on the AV equipment and start playing the video image.
For digital content video image:
3
Press the
button to switch the input signal.
z Select [DIGITAL VIDEO] as the input signal.
4
Press the
button twice.
P70
z Adjust the input signal, focusing, keystone distortion, and so on automatically
using the auto setup function.
5
Press the
P70
button.
z Select an appropriate image mode depending on the projecting image.
P55*
z Select an appropriate screen mode from the [Aspect] menu.
P73, 90, 91
Stopping projection...
Turn off the projector.
P60*
z Turn off the projector and remove the power cord from the AC outlet.
* Those steps are same as those for projecting the computer screen.
Downloaded From projector-manual.com Canon Manuals
69
Performing the Auto Setup
With the auto setup function, a series of screen adjustment and settings, such as Auto
focus and Auto keystone is performed automatically when projecting a video image from
an AV equipment. You can start the projection only with this operation if the input signal has
been appropriately selected.
Refer to page 46 for detailed information on items adjusted by performing the auto setup.
PROJECTING AN IMAGE FROM AV EQUIPMENT
1
Select [DIGITAL VIDEO].
Perform the steps shown in the "Selecting DIGITAL VIDEO" section on page 71 before
performing the auto setup if you want to project a digital content video image.
Skip this step if [DIGITAL VIDEO] has been selected at the previous projection.
2
Press the [AUTO SET] button.
The [Auto setup] window appears.
3
Press the [AUTO SET] button again.
One or more functions highlighted in black are performed automatically.
z You can perform this step by selecting [OK] with the [<] button, and then pressing the
[OK] button.
Selecting an Input Signal
Select [DIGITAL VIDEO] among the following input signals by following the steps shown in
the "Selecting DIGITAL VIDEO" section below if you want to project a digital content video
image.
DIGITAL VIDEO : Digital signal
Connecting with an HDMI/DVI cable or DVI digital
cable
COMPONENT : Component signal Connecting with a supplied component cable
SCART
: SCART signal
Connecting with a supplied SCART cable
VIDEO
: Video signal
Connecting with a video cable
S-VIDEO
: S-VIDEO
Connecting with an S-Video cable
The component, video, and S-VIDEO signals are automatically set if a cable is connected
and the input signal is confirmed.
z A LED (green) on a terminal flashes when an input signal is confirmed. The LED turns on if
the signal is selected and projected (P26, 27).
z Connecting with a HDMI/DVI cable, the image may be projected with the minimum resolution (480p or 575p) due to the specification of the AV equipment.
Downloaded From projector-manual.com Canon Manuals
70
„ Selecting DIGITAL VIDEO
1
Press the [INPUT] button.
The [INPUT] window appears.
2
Select the top item in the menu with the [INPUT] button.
The selection is toggled through available input signal types from above.
<
If [DIGITAL VIDEO] is unavailable from the list at the left, press [>], and then press [ ] /
[ ] to select it from the list at the right.
4
Press the [OK] button.
<
3
<
Downloaded From projector-manual.com Canon Manuals
71
PROJECTING AN IMAGE FROM AV EQUIPMENT
<
z You can select any input signal type from all options through the [ ] / [ ] button.
„ Selecting SCART
z Select [SCART] for Input Terminal-2.
Press the [INPUT] button.
The [INPUT] window appears.
2
Select the second top item in the menu with the [INPUT] button.
The selection is toggled through available input signals from above.
PROJECTING AN IMAGE FROM AV EQUIPMENT
1
<
<
z You can select any input signal type from all options through the [ ] / [ ] button.
4
Press the [OK] button.
<
If the SCART is unavailable from the list at the left, press [>], and then press [ ] / [ ] to
select the SCART from the list at the right.
Downloaded From projector-manual.com Canon Manuals
72
<
3
Selecting a Screen Mode (Aspect)
You can select one of the following screen modes depending on the aspect ratio of your AV
equipment or content software.
z You can specify the aspect ratio from the menu. Refer to [Aspect] in the menu (P90,
91).
z The available screen mode will be different depending on the setting of [Screen
aspect]. Refer to the section [Screen aspect] for details (P74).
„ Full screen
Select this to project a video image with aspect
ratio of 4:3.
[Full screen] will be disappeared from the menu
screen if you select [16:9] or [16:9 D. image shift]
for [Screen aspect].
PROJECTING AN IMAGE FROM AV EQUIPMENT
„ 4:3
Select this to project a screen with aspect ratio of
4:3 on the 16:9 screen if you have selected [16:9]
or [16:9 D. image shift] for [Screen aspect].
„ Wide
Select this to project a video image with aspect
ratio of 16:9.
z Refer to the table on the page 133 for more
detailed information on the screen size for the
wide screen.
„ Auto ([DIGITAL VIDEO]/[COMPONENT])
Select this to switch between [Full screen] and
[Wide] automatically in accordance with the video
image.
z The upper, lower, left and right portions of a
projected image may be missing depending
on the [Aspect] setting.
Downloaded From projector-manual.com Canon Manuals
73
Selecting Aspect Ratio of the Projecting Image
(Screen aspect)
You can select among three aspect ratios of the projecting image according to the aspect
ratio of the projected screen.
You can project an image on the whole screen by setting [Screen aspect].
z You can set [Screen aspect] from menu. Refer to the section [Screen aspect] on the
menu for details (P101).
„ 4:3
Select this when you use a screen with aspect ratio of 4:3.
The following table shows the available [Aspect] mode for each input signal.
Input signal
Available [Aspect] mode
PROJECTING AN IMAGE FROM AV EQUIPMENT
VIDEO
S-VIDEO
SCART
Full screen
Wide
COMPONENT
DIGITAL VIDEO
Full screen
Auto
Wide
„ 16:9
Select this when you use a screen with aspect ratio of 16:9.
Select [4:3] from the [Aspect] menu if you want to project a video image with aspect ratio of
4:3 in this mode (P73).
The following table shows the available [Aspect] mode for each input signal.
Input signal
Available [Aspect] mode
VIDEO
S-VIDEO
SCART
4:3
Wide
COMPONENT (480i/575i/480p/575p)
DIGITAL VIDEO (480p/575p)
4:3
Wide
COMPONENT (720p/1035i/1080i)
DIGITAL VIDEO (720p/1080i)
Wide
z [Auto screen color] may not correct the screen color properly. If such is the case, correct it
manually. (P98)
Downloaded From projector-manual.com Canon Manuals
74
„ 16:9 D. image shift
Select this when you use a screen with aspect ratio of 16:9. You can vertically shift or finetune the position of the undistorted image without the keystone adjustment.
Refer to P59 for detailed information on shifting the image.
The following table shows the available [Aspect] mode for each input signal.
Input signal
Available [Aspect] mode
VIDEO
S-VIDEO
SCART
4:3
Wide
COMPONENT (480i/575i/480p/575p)
DIGITAL VIDEO (480p/575p)
4:3
Wide
COMPONENT (720p/1035i/1080i)
DIGITAL VIDEO (720p/1080i)
Wide
z Keystone adjustment will be disabled. Project the image at right angle to the screen.
z [Auto focus], [Auto keystone], and [Auto screen color] are disabled in the [Auto setup] function.
z You cannot register the image for [Projector on] or [No signal screen].
z [SPOT] will be disabled.
Downloaded From projector-manual.com Canon Manuals
75
PROJECTING AN IMAGE FROM AV EQUIPMENT
Select [4:3] from the [Aspect] menu if you want to project a video image with aspect ratio of
4:3 in this mode (P73).
Downloaded From projector-manual.com Canon Manuals
Table of contents/Safety Instructions
Before Use
Setting Up the Projector
USEFUL
FUNCTIONS
AVAILABLE
DURING A
PRESENTATION
Projecting an Image from the Computer
Projecting an Image from AV Equipment
Useful Functions Available During a Presentation
Setting Up Functions from Menus
Maintenance
Troubleshooting
Appendix
Index
Downloaded From projector-manual.com Canon Manuals
Useful Functions Available During
a Presentation
USEFUL FUNCTIONS AVAILABLE DURING A PRESENTATION
Blackened Out an Image
Temporarily
Freezing the Picture
X Useful when:
X You finished the presentation.
X You want to divert attendees' attention
from the screen.
X Useful when:
X You want to perform a computer operation which is irrelevant to the proceedings of the presentation.
X You want to stop a moving image.
Blacken out the image temporarily.
Freeze the moving image.
Blackening out an Image
Freezing an Image
The screen changes to black or blue.
The "FREEZE" message is shown on the
screen.
Showing the Image Again
Press the
again.
button to show the image
z You can capture a specified logo
(SX60) (P98).
z You can show a logo such as a company logo while blackening out the
image (SX60) (P100).
z The (middle) LED illumination lamp on
the top control flash slowly while
blackening out the image.
z A guiding message appears if you
press an invalid button while the NO
SHOW function is on.
Canceling the FREEZE function
Press the
button again to cancel the
FREEZE function.
z The lamp keeps a turn-on state while
the NO SHOW function is on.
Downloaded From projector-manual.com Canon Manuals
78
z You can expand or reduce the frozen
image (P81).
z The (left and right) LED illumination
lamps on the top control flashes
slowly while stopping the image.
z A guiding message appears if you
press an invalid button while the
FREEZE function is on.
Muting the Sound
Adjusting the Volume
X Useful when:
X You want to immediately mute the sound
from the projector.
X Useful when:
X You want to adjust the volume level of
the projectors speaker.
Mute the sound temporarily.
Adjusting the Volume
Muting the Sound
Volume bar appears on the screen.
USEFUL FUNCTIONS AVAILABLE DURING A PRESENTATION
The projector shows the [MUTE] icon on
the screen.
Canceling the MUTE function
Press the
button again to cancel the
MUTE function.
Pressing the
MUTE function.
button also cancels the
z For SX7 MarkII, you can also mute the
audio with the same operation when
you output the audio to the external
audio-visual equipment.
Downloaded From projector-manual.com Canon Manuals
z Adjust the volume or mute setting on
the computer if the volume level is too
low.
z For SX7 MarkII, you can also adjust
the volume level with the same operation when you output the audio to the
external audio-visual equipment.
79
Showing the Elapsed Time
Page Up or Down through
the Pages
X Useful when:
X You want to manage the proceedings of
the presentation.
X Useful when:
X You want to page up or down through
the projected application pages with the
remote control.
The elapsed time from 00:00 to 59:59 is
displayed at the lower right corner of the
screen.
You can page up or down in the projected
application with the supplied remote control.
USEFUL FUNCTIONS AVAILABLE DURING A PRESENTATION
Starting the Countdown
Page Up
Press this button once to display the timer
and start counting.
Stopping the Countdown
Press the
countdown.
Page Down
button again to stop the
Canceling the Countdown
Press the
timer.
button again to disappear the
Downloaded From projector-manual.com Canon Manuals
80
z This function is available only if the
projector and the computer are connected via the USB cable that came
with your projector (P82).
z This function acts as the Page Up and
Page Down keys on the computer
keyboard. You can not use this function depending on the application.
Zooming an Image
X Useful when:
X Zoom in an object such as a small
graph during a presentation.
X Moving unnecessary information off the
screen to focus on the current subject.
Zoom the projected image.
Moving an Image to the Desired Position
If the image you want to zoom in stays out
of the screen or out of the center of the
screen, you can move it to the desired
position.
Zooming In an Image
USEFUL FUNCTIONS AVAILABLE DURING A PRESENTATION
Press this button repeatedly until the image
becomes the desired size.
Zooming Out an Image
z The magnification appears on the
screen when you press the [D.ZOOM]
button.
z The zoom ratio is 1x to 12x.
z You can freeze the enlarged image.
z Press the [OK] button to cancel the
digital zoom function.
z The following guiding message
appears if you press an invalid button
during operating the digital zoom
function.
Press this button repeatedly until the image
becomes the desired size.
You can restore the original size of the
image by pressing the [OK] button.
Downloaded From projector-manual.com Canon Manuals
81
Operating a Mouse with
the Remote Control
X Useful when:
X You want to operate a mouse with the
remote control.
You can use the supplied remote control as
the wireless mouse for your computer.
z This function is supported on Windows
7, Windows Vista, Windows XP, or Mac
OS 9.2 and later.
Moving the Cursor
Connecting a USB Cable
Make sure that both the computer and projector are turned off, and then connect the
supplied USB cable between the USB terminals on the computer and the projector.
USEFUL FUNCTIONS AVAILABLE DURING A PRESENTATION
USB terminal
You can move the mouse cursor vertically
and horizontally.
Computer
Using the Left Button of the Mouse
USB cable
You can click, double-click, or drag an
object with this button.
Using the Right Button of the Mouse
Projector
USB terminal
Downloaded From projector-manual.com Canon Manuals
82
Pointing with a Spotlight
X Useful when:
X You want to point to a portion of an
image that should draw attendees'
attention.
Moving the Spotlight
Highlight a desired portion of the projected
image with a spotlight.
Move the spotlight to a desired position.
USEFUL FUNCTIONS AVAILABLE DURING A PRESENTATION
z If you select [16:9 D. image shift] for
[Screen aspect], the SPOT function
will be disabled.
z Press the [OK] button to cancel the
SPOT function.
Showing the Spotlight
A spotlight appears at the center of the
screen and the image becomes dark
except for the spotlight.
Press the
button repeatedly to change
the shape of the spotlight.
No mark
Downloaded From projector-manual.com Canon Manuals
83
Downloaded From projector-manual.com Canon Manuals
Table of contents/Safety Instructions
Before Use
Setting Up the Projector
SETTING UP
FUNCTIONS
FROM MENUS
Projecting an Image from the Computer
Projecting an Image from AV Equipment
Useful Functions Available During a Presentation
Setting Up Functions from Menus
Maintenance
Troubleshooting
Appendix
Index
Downloaded From projector-manual.com Canon Manuals
Setting Up Functions from Menus
How to Use Menus
Some of the projector's function are used through the menu screen.
It consists of following three menus.
Display settings menu (P90)
This menu is used to select an input
signal and make various settings
related to display.
Image adjustment menu (P102)
This menu is used to make various
adjustments to the projected image.
You can make the adjustments
according to your preference while
checking the image.
SETTING UP FUNCTIONS FROM MENUS
System settings menu (P111)
This menu is used to set various functions of the projector.
You can set them regardless of the
input signal.
* The menu items may differ depending on the input signal.
The projector stores the settings for each input signal (8) and image mode (up to 5).
Symbols Indicating Item Categories
Menu items are classified into two categories, menu items used to project the image
from the computer and menu items used to project the image from the AV equipment.
Menu item used when projecting an image
from the computer.
DIGITAL PC
DIGITAL PC input
ANALOG PC
ANALOG PC-1/ANALOG PC-2 input
Menu item used when projecting an
image from AV equipment.
DIGITAL VIDEO
COMPONENT input
SCART
SCART input
COMP./SCART
COMPONENT input/SCART input
VIDEO/S-VIDEO
VIDEO input/S-VIDEO input
Downloaded From projector-manual.com Canon Manuals
86
DIGITAL VIDEO input
COMP.
This section provides the basic operation on the menu.
1
Press the [MENU] button.
A menu window appears.
z Press the [MENU] button again to close
the menu window.
2
<
Press [<] / [>] to select the appropriate tab.
Press [ ] to move the cursor on the tab if it is
not on it.
System settings
tab
SETTING UP FUNCTIONS FROM MENUS
<
Press [ ] / [ ] to select a menu item you want to set.
<
3
Image adjustment tab (Image adj.)
Display settings
tab
z Some menu items provide more detailed
menu items.
Menu items
(Continue to the next page.)
Downloaded From projector-manual.com Canon Manuals
87
Set the menu item.
There are four types of menu items that you make a setting:
z Directly
z From a list
z With a slider
z In a different screen
z Directly
Example: Tracking
z From a list
Example: Aspect
SETTING UP FUNCTIONS FROM MENUS
z With a slider
Example: Contrast
z In a different screen
Example: Menu position
(SX7 MarkII)
Press [<] [>] to move the slider.
Downloaded From projector-manual.com Canon Manuals
88
Press the [OK] button to display a list.
Press [ ] [ ] to select a desired setting.
<
Press [<] [>] to increase/decrease the
setting.
<
4
Press the [OK] button to display a different screen. Then follow the instruction on the screen.
5
Press the [OK] button.
In some menu items, the setting is enabled just by making a selection.
6
Press the [MENU] button when you finish.
The menu disappears.
SETTING UP FUNCTIONS FROM MENUS
Downloaded From projector-manual.com Canon Manuals
89
Setting Display Status
Selecting a Screen Mode (1)
Selecting a Screen Mode (2)
[Aspect]
[Aspect]
DIGITAL PC
ANALOG PC
DIGITAL VIDEO
COMP.
You can adjust the aspect ratio of the image projected on the screen.
You can adjust the aspect ratio of the image projected on the screen.
T
Display settings
T
Display settings
T
Aspect
T
Aspect
SETTING UP FUNCTIONS FROM MENUS
Auto
Projects a computer screen with
aspect ratio of 4:3 within the screen
with aspect ratio of 16:9.
Switches among [Full screen], [4:3],
and [Wide] automatically in accordance with the video image from the
AV equipment.
Full screen
Projects an input signal image in the
maximum size with the aspect ratio
unchanged.
Projects a normal image with aspect
ratio of 4:3 on the screen with
aspect ratio of 4:3.
4:3
Projects a computer screen at 16:9
aspect ratio with its width matching
to the width of the projecting area.
Projects a image with aspect ratio of
4:3 within the screen with aspect
ratio of 16:9.
Wide
Projects a video image with aspect
ratio of 16:9.
Full screen
Projects a computer screen with
aspect ratio of 4:3 fully on the
screen with aspect ratio of 4:3.
4:3
Auto
Wide
True size
Projects a computer screen in its
original size (no enlargement/reduction).
Press the [MENU] button when you finish.
Press the [MENU] button when you finish.
z Each item may become unavailable
depending on the setting of the input
signal or other menu items.
Downloaded From projector-manual.com Canon Manuals
90
z Each item may become unavailable
depending on the setting of [Screen
aspect].
Setting Display Status
Selecting a Screen Mode (3)
Selecting an Input Signal Type (1)
[Aspect]
[Input signal select]
VIDEO/S-VIDEO
SCART
ANALOG PC
You can adjust the aspect ratio of the image projected on the screen.
You can select a desired input signal type if the
auto PC adjustment function detects more than
one input signal types.
T
Display settings
T
Display settings
T
Aspect
T
Input signal select
Projects a normal image with aspect
ratio of 4:3 on the screen with
aspect ratio of 4:3.
4:3
Projects an image with aspect ratio
of 4:3 within the screen with aspect
ratio of 16:9.
Wide
Projects a video image with aspect
ratio of 16:9.
Select an input signal type suitable for the computer from the displayed signal types.
Press the [MENU] button when you finish.
z See P132 for the signal types supported by this projector.
Press the [MENU] button when you finish.
z Each item may become unavailable
depending on the setting of [Screen
aspect].
Downloaded From projector-manual.com Canon Manuals
91
SETTING UP FUNCTIONS FROM MENUS
Full screen
Selecting an Input Signal Type (2)
Selecting an Input Signal Type (3)
[Input signal select]
[Input signal select]
VIDEO/S-VIDEO
COMP./SCART
You can select an input signal type manually if a
video image from a AV equipment is not projected correctly (irregular color or no image).
You can select an input signal type manually if a
video image from a AV equipment is not projected correctly.
T
Display settings
T
Display settings
T
Input signal select
T
Input signal select
SETTING UP FUNCTIONS FROM MENUS
Auto
Selects the input signal automatically.
Auto
NTSC
Select one of input signal types
shown on the left if video image is
not projected correctly in the [Auto]
mode.
Selects the component format automatically according to the input signal.
1080i
Select one of input signal types
shown on the left if video image is
not projected correctly in the [Auto]
mode. ("575i" is selected automatically for the SCART input.)
PAL
SECAM
1035i
720p
NTSC4.43
575p
PAL-M
480p
PAL-N
575i
Press the [MENU] button when you finish.
480i
z Confirm the input signal type according to the User's Manual that came
with the AV equipment connected.
Press the [MENU] button when you finish.
Downloaded From projector-manual.com Canon Manuals
92
z Confirm the input signal type according to the User's Manual that came
with the AV equipment connected.
Setting Display Status
Adjusting the Total Number of Dots
Adjusting the Tracking
[Total dots]
[Tracking]
ANALOG PC
ANALOG PC
You can select the total number of dots in the
horizontal direction. Adjust the number of dots
when the image distorts or noise is displayed on
the screen at both sides.
You can fine-tune the timing for generating an
image from the image signal. Adjust the tracking
when the image flickers or distorts.
T
Display settings
T
Display settings
T
Input signal settings
T
Input signal settings
T
Total dots
T
Tracking
Increases the total number of dots.
>
Increases the set value.
<
Decreases the total number of dots.
<
Decreases the set value.
Press the [MENU] button when you finish.
SETTING UP FUNCTIONS FROM MENUS
>
Press the [MENU] button when you finish.
z Perform this adjustment if the auto PC
adjustment function cannot adjust the
project image correctly.
z The setting is recorded for [ANALOG
PC-1] and [ANALOG PC-2] separately.
Downloaded From projector-manual.com Canon Manuals
z Perform this adjustment if the auto PC
adjustment function cannot adjust the
project image correctly.
z The setting is recorded for [ANALOG
PC-1] and [ANALOG PC-2] separately.
93
Adjusting the Horizontal Position
Adjusting the Vertical Position
[Horizontal position]
[Vertical position]
ANALOG PC
ANALOG PC
You can adjust the horizontal position of the
screen when the projected image is shifted in
the horizontal direction.
You can adjust the vertical position of the screen
when the projected image is shifted in the vertical direction.
T
Display settings
T
Display settings
T
Input signal settings
T
Input signal settings
T
Horizontal position
T
Vertical position
SETTING UP FUNCTIONS FROM MENUS
>
Moves the screen to the right.
>
Moves the screen up.
<
Moves the screen to the left.
<
Moves the screen down.
Press the [MENU] button when you finish.
Press the [MENU] button when you finish.
z Perform this adjustment if the auto PC
adjustment function cannot adjust the
project image correctly.
z The setting is recorded for [ANALOG
PC-1] and [ANALOG PC-2] separately.
Downloaded From projector-manual.com Canon Manuals
94
z Perform this adjustment if the auto PC
adjustment function cannot adjust the
project image correctly.
z The setting is recorded for [ANALOG
PC-1] and [ANALOG PC-2] separately.
Setting Display Status
Adjusting the Number of Horizontal Pixels
Adjusting the Number of Vertical Pixels
[Horizontal pixels]
[Vertical pixels]
ANALOG PC
ANALOG PC
You can adjust the number of the pixels in the
horizontal direction if the length of the screen is
too long or too short in the horizontal direction.
You can adjust the number of the pixels in the
vertical direction if the length of the screen is too
long or too short in the vertical direction.
T
Display settings
T
Display settings
T
Input signal settings
T
Input signal settings
T
Horizontal pixels
T
Vertical pixels
Increases the number of pixels in
the horizontal direction.
>
Increases the number of pixels in
the vertical direction.
<
Decreases the number of pixels in
the horizontal direction.
<
Decreases the number of pixels in
the vertical direction.
Press the [MENU] button when you finish.
Press the [MENU] button when you finish.
z Perform this adjustment if the auto PC
adjustment function cannot adjust the
project image correctly.
z The setting is recorded for [ANALOG
PC-1] and [ANALOG PC-2] separately.
Downloaded From projector-manual.com Canon Manuals
z Perform this adjustment if the auto PC
adjustment function cannot adjust the
project image correctly.
z The setting is recorded for [ANALOG
PC-1] and [ANALOG PC-2] separately.
95
SETTING UP FUNCTIONS FROM MENUS
>
Performing Progressive Processing
Selecting a Menu Position
[Progressive]
[Menu position]
COMP.
VIDEO/S-VIDEO
DIGITAL PC
ANALOG PC
DIGITAL VIDEO
COMP./SCART
VIDEO/S-VIDEO
You can accumulate and composite information
for a signal for a low resolution image to convert
it to a high resolution image.
You can select the position of the menu displayed on the screen.
T
Display settings
T
Display settings
T
Progressive
T
Menu position
On
Performs the progressive processing.
Auto
Performs the appropriate progressive processing depending on the
input signal.
Move the menu to the desired position with [ ],
[<], [ ], and [>], and then press the [OK] button.
<
Does not perform the progressive
processing.
<
SETTING UP FUNCTIONS FROM MENUS
Off
Press the [OK] button to confirm, and then press
the [MENU] button.
z You can use this function if the input
signal is VIDEO/S-VIDEO or the component signal is 575i or 480i.
You cannot use this function if the
component signal is 1080i, 1035i,
720p, 575p, or 480p.
z This setting is saved for the currently
selected input signal.
z Select [Off] when flickers and horizontal lines are noticeable on a fast-moving picture.
z See P136 for more detailed information on the progressive processing.
Press the [MENU] button when you finish.
Downloaded From projector-manual.com Canon Manuals
96
Setting Display Status
Performing the Ceiling-mounted/Rear
Projection
[Image flip H/V]
DIGITAL PC
DIGITAL VIDEO
ANALOG PC
COMP./SCART VIDEO/S-VIDEO
You can make this setting if you want to hang the
projector from the ceiling or project an image on
a transmissive screen.
None (Normal image)
T
Display settings
T
Image flip H/V
Ceiling mounted
SETTING UP FUNCTIONS FROM MENUS
Rear
None
Ceiling mounted
Rear
Select this if you project an image
normally.
Select this if you project
with the projector hung
ceiling. The projected
inverted in both vertical
zontal directions.
an image
from the
image is
and hori-
Select this if you project an image
from behind the screen. The projected image is inverted in the horizontal direction.
Rear, Ceiling mounted Select this if you project an image
from behind the screen with the projector hung from the ceiling. The
projected image is inverted in the
vertical direction.
Rear, Ceiling mounted
Press the [MENU] button when you finish.
z When hanging the projector from the
ceiling, make sure to use optional
brackets. Contact your Canon dealer.
z The keystone adjustment will be reset.
Downloaded From projector-manual.com Canon Manuals
97
Correcting the Screen Color
Capturing a Logo to Be Projected
(SX60)
[Screen color]
DIGITAL PC
[Logo capture]
ANALOG PC
DIGITAL VIDEO
COMP./SCART VIDEO/S-VIDEO
You can adjust the while balance so that white
portions of the image are displayed correctly.
DIGITAL PC
ANALOG PC
DIGITAL VIDEO
COMP./SCART
VIDEO/S-VIDEO
You can project a desired image (logo) when
you turn on the projector, there is no input signal,
or you blacken a projecting image temporarily.
T
Display settings
T
Display settings
T
Screen color
T
User screen settings
T
Logo capture
SETTING UP FUNCTIONS FROM MENUS
Normal
Greenboard
Adjust
Projects an image in a color tone
similar to that of natural light on a
standard screen.
Projects an image in an almost natural color tone on a greenboard (dark
green).
Adjusts color tone with the level
meter. To adjust the color tone automatically, press the [AUTO SET]
button when the following level
meter is displayed. Use this function
if the [Greenboard] setting is inadequate.
OK
Cancel
Projects the image to be captured
on the screen. Surround the capturing area with the red frame and
press [OK]. The image in the red
frame is captured.
Cancels the image capturing.
Press the [OK] button to confirm, and then press
the [MENU] button.
<
<
If you manually adjust it, press [ ] or [ ]
button to select red, green, or blue.
[>] Increases the color tone of each color.
[<] Decreases the color tone of each color.
Press the [OK] button to confirm, and then press
the [MENU] button.
z If you select [16:9 D. image shift] for
[Screen aspect], the auto screen color
correction function will be disabled.
Downloaded From projector-manual.com Canon Manuals
98
z You can capture only one image.
z For projecting the captured logo on a
screen, select [User logo] on the [Projector on], [No signal screen], or [NO
SHOW] menu item.
z You may not capture an image
depending on the resolution and scan
system.
z If you select [16:9] or [16:9 D. image
shift] for [Screen aspect], you cannot
capture an image.
Setting Display Status
Selecting a Logo Display Position
(SX60)
Displaying a Logo (No signal screen)
[No signal screen]
[Logo position]
DIGITAL PC
ANALOG PC
DIGITAL PC
ANALOG PC
DIGITAL VIDEO
COMP./SCART
VIDEO/S-VIDEO
You can select a logo display position. You can
place the logo at the center or a corner of the
screen.
You can display a user logo on a screen when
there is no input signal. (SX60)
For SX7 MarkII, you can display either of a black
or blue screen.
T
Display settings
T
Display settings
T
User screen settings
T
User screen settings
T
Logo position
T
No signal screen
DIGITAL VIDEO
COMP./SCART VIDEO/S-VIDEO
Upper R
Select a position you want to display a logo and press the [OK] button.
Center
Press the [MENU] button when you finish.
Displays no logo (black screen).
Blue
Displays no logo (blue background).
User logo
Lower L
Lower R
Black
Displays a logo captured on the
[Logo capture] screen. (SX60)
Press the [OK] button to confirm, and then press
the [MENU] button.
z You cannot select [Logo position] if
you have not captured a logo on the
[Logo capture] screen.
Downloaded From projector-manual.com Canon Manuals
z You cannot select [User logo] if you
have not captured a logo on the [Logo
capture] screen. (SX60)
99
SETTING UP FUNCTIONS FROM MENUS
(SX60)
Upper L
Displaying a Logo (NO SHOW)
Selecting a Logo at Startup
[NO SHOW]
[Projector on]
DIGITAL PC
ANALOG PC
DIGITAL VIDEO
COMP./SCART VIDEO/S-VIDEO
You can display a user logo on a screen when
the projected image is blackened out temporarily by pressing the [NO SHOW] button on the
remote control. (SX60)
For SX7 MarkII, you can display either of a black
or blue screen.
DIGITAL PC
ANALOG PC
DIGITAL VIDEO
COMP./SCART
VIDEO/S-VIDEO
You can display a specified logo on a screen
from the moment the projector is turned on to the
moment it is ready for projection.
T
Display settings
T
User screen settings
T
Display settings
T
Projector on
T
User screen settings
T
NO SHOW
(SX60)
SETTING UP FUNCTIONS FROM MENUS
(SX60)
Displays the Canon logo captured
at the factory.
Skip
Projects an image immediately after
turning on the projector.
User logo
Black
Displays no logo (black screen).
Blue
Displays no logo (blue background).
Displays a logo captured on the
[Logo capture] screen. (SX60)
User logo
Displays a logo captured on the
[Logo capture] screen. (SX60)
Press the [OK] button to confirm, and then press
the [MENU] button.
Press the [OK] button to confirm, and then press
the [MENU] button.
z You cannot select [User logo] if you
have not captured a logo on the [Logo
capture] screen. (SX60)
Downloaded From projector-manual.com Canon Manuals
100
Canon logo
z You cannot select [User logo] if you
have not captured a logo on the [Logo
capture] screen. (SX60)
Setting Display Status
Selecting Aspect Ratio of the Screen
[Screen aspect]
DIGITAL PC
DIGITAL VIDEO
ANALOG PC
COMP./SCART VIDEO/S-VIDEO
You can select the aspect ratio of the projecting
screen.
T
Display settings
T
Screen aspect
Select this when you use a screen
with aspect ratio of 4:3.
16:9
Select this when you use a screen
with aspect ratio of 16:9.
16:9 D. image shift
Select this when you use a screen
with aspect ratio of 16:9 and you
want to move the projecting position
vertically.
SETTING UP FUNCTIONS FROM MENUS
4:3
Press the [MENU] button when you finish.
z If you select [16:9] or [16:9 D. image
shift], [Wide] will be selected for
[Aspect]. If you want to project an
image with aspect ratio of 4:3 when
selecting [16:9 D. image shift], select
[4:3] for [Aspect].
z If you select [16:9 D. image shift], the
keystone adjustment will be reset.
z An item may become unavailable in
this setting depending on the selecting input signal and screen aspect
(P74).
Downloaded From projector-manual.com Canon Manuals
101
Setting the Image Quality
Selecting an Image Mode
[Image mode]
DIGITAL PC
ANALOG PC
DIGITAL VIDEO
COMP./SCART VIDEO/S-VIDEO
You can select an image mode suitable for the
projecting image.
Home Cinema
Select this to project a movie with
quality suited to seriously enjoy the
atmosphere of a movie theater in a
dark room.
AdobeRGB
Select this if you want to project an
image in the display mode conforming to Adobe RGB color space. You
can project an image with more
accurate color reproduction since
Its has wider color gamut than
sRGB.
sRGB
Select this if you want to project an
image in the display mode conforming to Windows standard color
space. It is suited to project an
image shot by an sRGB-compatible
digital camera.
T
Image adjustment
T
Image mode
SX7 MarkII
SETTING UP FUNCTIONS FROM MENUS
Standard
Presentation
Movie*1
Photo*2
AdobeRGB
sRGB
(SX7 MarkII)
Standard
Select this to project an image with
near-original quality and a high
regard for reproduction of white. It is
also suited to project moving pictures such as a TV program or a
DVD movie in a bright room.
Presentation
Select this to project an image with
quality suited for the presentation. It
also suited to project moving pictures with a high regard for the
brightness.
Movie
Select this to project moving pictures of all kinds. Its brightness is
suited to easily enjoy the atmosphere of a movie theater in a dim
room.
Photo
If you select [Photo] for [Image
mode], make sure to set [Ambient
light] in the [Image adjustment] as
well.
You can correct an image according
to the ambient light based on
[sRGB] in [Image mode] and project
the image with higher tone on the
screen by setting [Ambient light]. It
is suited to project an ornamental
photo, etc. under an ambient light.
*1 It is available if the input signal is [DIGITAL VIDEO],
[COMPONENT], [VIDEO] or [S-VIDEO].
*2 It is available if the input signal is [ANALOG PC-1],
[ANALOG PC-2], or [DIGITAL PC].
Press the [OK] button to confirm, and then press
the [MENU] button.
Downloaded From projector-manual.com Canon Manuals
102
SX60
Standard
Presentation
Movie
Home Cinema
sRGB
z You can adjust the image quality
(brightness, contrast, etc.) for each
image mode as you wish.
z The results of adjustments are saved
for each input signal. Once you save
them, you can project images with the
same settings.
Setting the Image Quality
Adjusting the Brightness
Adjusting the Contrast
[Brightness]
[Contrast]
DIGITAL PC
ANALOG PC
DIGITAL VIDEO
COMP./SCART VIDEO/S-VIDEO
DIGITAL PC
ANALOG PC
DIGITAL VIDEO
COMP./SCART
VIDEO/S-VIDEO
You can adjust the brightness of an image when
it is too bright or dark.
You can adjust the contrast of an image if you
want to make it more or less vivid, adjust the difference in tone between the lightest and darkest
portions of the image.
T
Image adjustment
T
Image adjustment
T
Brightness
T
Contrast
(SX7 MarkII)
>
Increases the brightness of an
image.
>
Increases the contrast of an image.
The image becomes more vivid.
<
Decreases the brightness of an
image.
<
Decreases the contrast of an image.
The image becomes less vivid.
Press the [MENU] button when you finish.
Press the [MENU] button when you finish.
z This setting is saved for the currently
selected input signal and image
mode.
Downloaded From projector-manual.com Canon Manuals
z This setting is saved for the currently
selected input signal and image
mode.
103
SETTING UP FUNCTIONS FROM MENUS
(SX7 MarkII)
Adjusting the Sharpness
Making a Gamma Correction
[Sharpness]
[Gamma]
DIGITAL PC
ANALOG PC
DIGITAL VIDEO
COMP./SCART VIDEO/S-VIDEO
DIGITAL PC
ANALOG PC
DIGITAL VIDEO
COMP./SCART
VIDEO/S-VIDEO
You can adjust the sharpness when you want to
make an image sharper or softer.
You can make a gamma correction if light or
dark portions of an image are obscure.
T
Image adjustment
T
Image adjustment
T
Sharpness
T
Gamma
SETTING UP FUNCTIONS FROM MENUS
(SX7 MarkII)
(SX7 MarkII)
>
Increases the sharpness of an
image.
>
Makes dark and obscure portions of
an image visible.
<
Decreases the sharpness of an
image.
<
Makes light and obscure portions of
an image visible.
Press the [MENU] button when you finish.
Press the [MENU] button when you finish.
z This setting is saved for the currently
selected input signal and image
mode.
Downloaded From projector-manual.com Canon Manuals
104
z This setting is saved for the currently
selected input signal and image
mode.
Setting the Image Quality
Making Color Adjustment (1) (SX7 II)
Making Color Adjustment (2)
[Color adjustment]
[Color adjustment]
DIGITAL PC *
DIGITAL PC
ANALOG PC
You can adjust color level and color balance and
make color adjustment for each color (red,
green, and blue).
DIGITAL VIDEO
You can make color adjustment for each color
(red, green, and blue).
T
Image adjustment
T
Color adjustment
T
Color adjustment
R/G/B Gain
(Refer to "Making Color Adjustment
(1)")
[>] Changes to the blue color (cold
color).
R/G/B Offset
(Refer to "Making Color Adjustment
(1)")
Press the [MENU] button when you finish.
Adjusts the intensity of each color.
[>] Increases the color intensity.
[<] Decreases the color intensity.
R/G/B Offset
z This setting is saved for the currently
selected input signal and image
mode.
Adjusts the color reproducibility of
dark portions of each color.
[>] Increases the color reproducibility of color.
[<] Decreases the color reproducibility of color.
*
You can set this if you have selected [Photo]
for [Image mode].
Press the [MENU] button when you finish.
z This setting is saved for the currently
selected input signal and image
mode.
z If you change R/G/B Gain or Offset
once color temperature has been
specified, the "*" mark is displayed at
the right side of the setting value to
indicate the color temperature has
been specified.
Downloaded From projector-manual.com Canon Manuals
105
SETTING UP FUNCTIONS FROM MENUS
Adjusts the color temperature of the
image.
[<] Changes to the red color (warm
color).
R/G/B Gain
SCART
* is only applicable to SX60
T
Image adjustment
Color temperature*
ANALOG PC *
Making Color Adjustment (3)
Making Advanced Color Adjustment (1)
[Color adjustment]
[Dynamic gamma]
COMP.
DIGITAL PC
ANALOG PC
DIGITAL VIDEO
COMP./SCART
VIDEO/S-VIDEO
VIDEO/S-VIDEO
You can adjust color level and color balance and
make color adjustment for each color (red,
green, and blue).
You can adjust the gradation representation of
light and dark portions of an image automatically.
T
Image adjustment
T
Image adjustment
T
Color adjustment
T
Advanced adjustment
T
Dynamic gamma
(SX60)
SETTING UP FUNCTIONS FROM MENUS
Color level
Adjusts the intensity of each color.
[>] Increases the intensity of color.
[<] Decreases the intensity of color.
Color balance
[>] Corrects a reddish image.
[<] Corrects a greenish image.
(Refer to "Making Color Adjustment
(1)")
R/G/B Offset
(Refer to "Making Color Adjustment
(1)")
Press the [MENU] button when you finish.
z You cannot make color adjustment if
the video format is PAL, PAL-M, PAL-N,
or SECAM.
z This setting is saved for the currently
selected input signal and image
mode.
Downloaded From projector-manual.com Canon Manuals
106
Disables dynamic gamma.
On
Enables dynamic gamma.
Press the [OK] button to confirm, and then press
the [MENU] button.
Adjusts the color balance of a reddish or greenish image.
R/G/B Gain
Off
z Dynamic gamma automatically optimizes image quality.
z This setting is saved for the currently
selected input signal and image
mode.
Setting the Image Quality
Making Advanced Color Adjustment (2)
Making Advanced Color Adjustment (3)
[Mem. color correct]
[6-axis color adjust]
DIGITAL PC
DIGITAL VIDEO
ANALOG PC
COMP./SCART VIDEO/S-VIDEO
You can correct colors (e.g. blue sky) in our
memory so that they can be projected more vividly.
DIGITAL PC
ANALOG PC
DIGITAL VIDEO
COMP./SCART
T
Image adjustment
T
Image adjustment
T
Advanced adjustment
T
Advanced adjustment
T
Mem. color correct
Disables the memorized color correction function.
L
Specifies the intensity of the memorized color correction in three steps.
T
6-axis color adjust
M
H
Press the [MENU] button when you finish.
Enables the 6-axis color adjustment.
Off
Disables the 6-axis color adjustment.
<
The 6-axis color adjustment box appears on the
screen if you select [Adjust].
Press [ ] / [ ] to select the [Hue] or [Saturation]
slider, and press [<] / [>] to make an adjustment.
Press the [MENU] button when you finish.
<
z This setting is saved for the currently
selected input signal and image
mode.
Adjust
z This setting is saved for the currently
selected input signal and image
mode.
Downloaded From projector-manual.com Canon Manuals
107
SETTING UP FUNCTIONS FROM MENUS
Off
VIDEO/S-VIDEO
You can make fine color adjustment with the 6axis color adjustment box (RGB (red/green/blue)
and CMY (cyan/ magenta/yellow)).
Refer to Glossary for information on the 6-axis
color adjustment.
Correcting the Image According to
the Ambient Light (SX7 II)
[Ambient light]
DIGITAL PC
ANALOG PC
You can correct and project an image more
appropriately according to the ambient light on
the screen if you have selected [Photo] for
[Image mode].
Level
L
Select this if the ambient light is
dark.
M
Select this if the ambient light is
moderate.
T
Image adjustment
H
Select this if the ambient light is
bright.
T
Ambient light
An Example of the Ambient Light Setting
Level
SETTING UP FUNCTIONS FROM MENUS
Off
Projects an image with no correction.
Adjust
You can specify the type and level
(brightness) of the ambient light.
Type
A projection room, bar
M
Photo studio, galley
H
Conference room, lecture room
Press the [OK] button to accept your setting and
then press the [MENU] button.
Tungsten
Select this if the ambient light
source is a light bulb or bulb color
fluorescent.
Fluorescent
Select this if the ambient light
source is a day white fluorescent.
Fluorescent H
Select this if the ambient light
source is a daylight fluorescent.
Downloaded From projector-manual.com Canon Manuals
108
Example Location
L
z [Off] is the factory default.
z You can set this if you have selected
[Photo] for [Image mode].
Setting the Image Quality
Reducing the Lamp Brightness
[Lamp mode]
DIGITAL PC
ANALOG PC
DIGITAL VIDEO
COMP./SCART VIDEO/S-VIDEO
You can reduce the lamp brightness if you want
to make the image darker or reduce the fan
noise.
T
Image adjustment
T
Lamp mode
SETTING UP FUNCTIONS FROM MENUS
(SX7 MarkII)
Normal
Projects an image at the normal
brightness level.
Quiet
Reduces the lamp brightness and
the fan noise.
Press the [OK] button to confirm, and then press
the [MENU] button.
z You can reduce the power consumption of the lamp if you select in the
quiet mode.
z This setting is saved for the currently
selected input signal and image
mode.
Downloaded From projector-manual.com Canon Manuals
109
Resetting the Image Settings
[Reset]
DIGITAL PC
DIGITAL VIDEO
ANALOG PC
COMP./SCART VIDEO/S-VIDEO
You can reset the current image settings to the
default settings if you want to make all image
settings all over again.
Performing [Color adjustment] or [Advanced
adjustment]:
A check mark ( ) appears on the Image
Adjustment menu if you perform [Color
adjustment] or [Advanced adjustment
(Dynamic gamma, Mem. color correct, or
6-axis color adjust)].
T
Image adjustment
T
Reset
(SX7 MarkII)
OK
Cancel
Resets the image settings.
SETTING UP FUNCTIONS FROM MENUS
Cancels resetting of the image settings.
Press the [OK] button to confirm, and then press
the [MENU] button.
z The projector stores the image settings for each input signal (8) and
image mode (up to 5) separately. If
you select [OK], the settings saved for
the currently selected set of the input
signal and image mode are reset.
Downloaded From projector-manual.com Canon Manuals
110
Setting Various Function
Setting Auto Setup Function
Selecting the Power Management Mode
[Auto setup]
[Power management mode]
DIGITAL PC
ANALOG PC
DIGITAL VIDEO
COMP./SCART VIDEO/S-VIDEO
DIGITAL PC
ANALOG PC
DIGITAL VIDEO
COMP./SCART
VIDEO/S-VIDEO
You can select an item you want to enable in the
auto setup function.
You can turn off the lamp or projector automatically for saving power.
T
System settings
T
System settings
T
Auto setup
T
Power management mode
Select [On] or [Off] for the following items if you
want to enable or disable them in the auto setup
function, respectively.
Enables/disables the auto focusing.
Enables/disables the auto keystone
correction.
Off
Disables the power management
mode.
Auto input
Enables/disables the auto input
selection.
Standby
Auto screen color
Enables/disables the auto screen
color correction.
Enters the power management
mode. The projector restarts projection when a signal is inputted or any
operation button is pressed.
Exit
Enters the exit mode and turns off
the projector automatically.
z A confirmation screen appears during
the auto setup so that you can check
which functions are enabled/disabled
(P46, 70).
z You can manually adjust each item.
[Auto focus]: [FOCUS] button (P51)
[Auto keystone]: [KEYSTONE] button
(P52)
[Auto input]: [INPUT] button (P48, 71)
[Auto screen color]: Menu function
(P98)
z If you select [16:9 D. image shift] for
[Screen aspect], you cannot change
the setting of each item. The auto
setup function will also be disabled.
Press the [OK] button to confirm, and then press
the [MENU] button.
Downloaded From projector-manual.com Canon Manuals
z You cannot enable the [Direct Power
on] function if you select [Off].
z The [POWER] indicator flashes red
and green when the projector is in the
[Standby] power management mode.
111
SETTING UP FUNCTIONS FROM MENUS
Auto focus
Auto keystone
Skip the POWER Button Operation
Enabling/Disabling the Beep
[Direct power on]
[Beep]
DIGITAL PC
DIGITAL VIDEO
ANALOG PC
COMP./SCART VIDEO/S-VIDEO
DIGITAL PC
ANALOG PC
DIGITAL VIDEO
COMP./SCART
VIDEO/S-VIDEO
You can set the projector to be turned on when
you connect the power cord.
You can enable/disable the beep when you
press a button on the top control or remote control.
T
System settings
T
System settings
T
Direct power on
T
Beep
SETTING UP FUNCTIONS FROM MENUS
Off
Disables the direct power on function.
Off
Disables the beep.
On
Enables the direct power on function.
On
Enables the beep.
Press the [OK] button to confirm, and then press
the [MENU] button.
Press the [OK] button to confirm, and then press
the [MENU] button.
z Wait at least 5 minutes before turning
on the projector when you turn off the
projector with the direct power on
function. It may shorten the lamp life if
you turn on the projector immediately
after turning it off.
z Set the previous [Power management
mode] to [Standby] or [Exit] in addition to this setting if you want to
enable the direct power on function.
Downloaded From projector-manual.com Canon Manuals
112
z It does not beep if you mute the projector sound temporarily with the
[MUTE] button.
Setting Various Function
Selecting a Display Language
[Language]
DIGITAL PC
ANALOG PC
DIGITAL VIDEO
COMP./SCART VIDEO/S-VIDEO
You can select a language to be used in the
menu from 20 different languages.
T
System settings
T
Language
Simplified Chinese
Germany
Traditional Chinese
Korean
French
Japanese
Italian
Spanish
Portuguese
Press the [OK] button and all words in the menu
will be displayed in the selected language.
Press the [MENU] button when you finish.
Swedish
Russian
Dutch
Finnish
Norwegian
Turkish
Polish
Hungarian
Czech
Danish
Downloaded From projector-manual.com Canon Manuals
113
SETTING UP FUNCTIONS FROM MENUS
English
Prohibiting the Projector Operation
Enabling/Disabling the Guide Message
[Key lock]
[Guide]
DIGITAL PC
DIGITAL VIDEO
ANALOG PC
COMP./SCART VIDEO/S-VIDEO
DIGITAL PC
ANALOG PC
DIGITAL VIDEO
COMP./SCART
VIDEO/S-VIDEO
You can prohibit the use of the buttons on the
top control or remote control to prevent them
from being pressed by mistake.
You can enable/disable the guide message
showing how to use the projector.
T
System settings
T
System settings
T
Key lock
T
Guide
SETTING UP FUNCTIONS FROM MENUS
Off
Main unit
Remote control
Disables the key lock function.
Off
Disables the guide message.
Prohibits the use of the top control.
On
Enables the guide message.
Prohibits the use of the remote control.
Press the [OK] button to confirm, and then press
the [MENU] button.
Press the [OK] button to confirm, and then press
the [MENU] button.
z The key lock function becomes effective from the moment when the [OK]
button is pressed after selecting [Main
unit] or [Remote control]. Be sure to
press the [OK] button on the top control or remote control which is not
locked.
z To unlock the key lock function forcibly, remove the power plug from the
AC outlet after the projection, and
then insert the power plug while holding down the [OK] button until the projector beeps.
Downloaded From projector-manual.com Canon Manuals
114
z The guide message appears on the
screen when:
- The projector is turned on (P40).
- The projector is turned off (the
[POWER] button is pressed) (P60).
- No input signal is confirmed (P36,
64).
- The invalid button is pressed under
NO SHOW, FREEZE, or D.ZOOM
(P78, 81).
Setting Various Function
Turning On/Off the LED Illumination
Setting up the Remote Control
[LED illumination]
[Remote control]
DIGITAL PC
DIGITAL VIDEO
ANALOG PC
COMP./SCART VIDEO/S-VIDEO
DIGITAL PC
ANALOG PC
DIGITAL VIDEO
COMP./SCART
VIDEO/S-VIDEO
You can turn on/off the LED illumination lamp
and the LEDs on the terminals (P26, 27, 28).
You can change the channel settings to prevent
the two remote controls from interfering with
each other when you use two projectors at the
same time.
T
System settings
T
System settings
T
LED illumination
T
Other settings
T
Remote control
Off
Turns off all LEDs.
On
Turns on LEDs as necessary.
Press the [OK] button to confirm, and then press
the [MENU] button.
z This setting does not effect the
POWER indicator or WARNING lamp.
Selects the channel on the projector
you use.
Ch2
Press the [OK] button to confirm, and then press
the [MENU] button.
Selecting a Channel on the Remote Control
Press the [LIGHT] button for 3 seconds while
holding down the [OK] button on the remote
control.
The above operation toggles the channel
between Ch1 (the button flashes once) and Ch2
(the button flashes twice).
z Make sure to set the same channel for
both remote control and projector.
z Performing this operation with the
remote control, you cannot control the
projector after pressing the [OK] button. Make sure to change the channel
for the remote control at the same
time.
Downloaded From projector-manual.com Canon Manuals
115
SETTING UP FUNCTIONS FROM MENUS
Ch1
Setting up the Digital Video Input Signal
Setting a Password
[Digital video]
[Password settings]
DIGITAL PC
ANALOG PC
DIGITAL VIDEO
COMP./SCART
DIGITAL VIDEO
VIDEO/S-VIDEO
You can select the standard of the digital video
input signal.
You can set a password to the projector.
Once you set the password, you will need to
enter the password each time you turn on the
projector.
T
System settings
T
System settings
T
Other settings
T
Other settings
T
Digital video
T
Password settings
Projects a full range digital signal.
Off
Disables the password protection.
L
Projects a limited range digital signal.
On
Enable the password protection.
Press the [OK] button to confirm, and then press
the [MENU] button.
Press the [OK] button to confirm, and then press
the [MENU] button.
z Once you set a password, the password entry screen appears at poweron. Enter a 4-digit password with [ ],
[ ], [<], and [>]. If the password is
valid, projection starts. If you enter a
wrong password three times, the projector will be turned off.
z To cancel the password, remove the
power plug from the AC outlet after
the projection, and then insert the
power plug while holding down the
[MENU] button until the projector
beeps.
<
z Refer to the User's Manual that came
with the AV equipment for more
detailed information on settings.
<
SETTING UP FUNCTIONS FROM MENUS
F
Downloaded From projector-manual.com Canon Manuals
116
Setting Various Function
Registering a Password
Resetting to the Default Setting
[Register password]
[Factory defaults]
DIGITAL PC
DIGITAL VIDEO
ANALOG PC
COMP./SCART VIDEO/S-VIDEO
DIGITAL PC
ANALOG PC
DIGITAL VIDEO
COMP./SCART
VIDEO/S-VIDEO
You can register a password that you need to
enter when turning on the projector.
You can reset the menu item settings and restore
the system settings to the factory defaults.
T
System settings
T
System settings
T
Other settings
T
Other settings
T
Register password
T
Factory defaults
OK
Resets the projector's menu item
settings.
Cancel
Cancels resetting the menu item
settings.
Press the [OK] button to confirm, and then press
the [MENU] button.
<
<
Enter a 4-digit password from the left. You can
enter a value 1, 2, 3, and 4 by pressing [ ], [ ],
[<], and [>], respectively. Once you enter a
value for all four digits, the password is registered automatically.
z Press the [MENU] button without
entering a password if you want to
cancel registering the password.
Downloaded From projector-manual.com Canon Manuals
z All adjustments are reset to default if
you perform [Factory defaults].
z The language selection screen
appears when you turn on the projector for the next time if you perform
[Factory defaults] (P41).
z The settings of [Lamp counter],
[Language] and [Remote control] will
not be reset even after resetting to the
factory defaults.
z For the factory defaults, see P144,
145.
117
SETTING UP FUNCTIONS FROM MENUS
Press the [OK] button to display the password
entry screen.
Resetting the Lamp Counter
[Lamp counter]
DIGITAL PC
ANALOG PC
DIGITAL VIDEO
COMP./SCART VIDEO/S-VIDEO
You can reset the lamp counter that indicates the
timing to replace the projector when you replace
it.
T
System settings
T
Other settings
T
Lamp counter
z Do not reset the lamp counter except
when you have replaced the lamp.
Otherwise, the lamp counter cannot
indicate the correct timing for replacing the lamp.
SETTING UP FUNCTIONS FROM MENUS
Display Examples of Lamp Counter
z If the time of use is:
SX7 MarkII : 1800 hours or less
SX60
: 2300 hours or less
z If the time of use is:
SX7 MarkII : 2000 hours or more
SX60
: 2500 hours or more
z If the time of use is:
SX7 MarkII : 1800 to 2000 hours
SX60
: 2400 to 2500 hours
z If you replace the lamp
OK
Cancel
Resets the lamp counter.
Cancels resetting the lamp counter.
Press the [OK] button to confirm, and then press
the [MENU] button.
z See P122 for more detailed information on replacing the lamp.
Downloaded From projector-manual.com Canon Manuals
118
Table of contents/Safety Instructions
Before Use
Setting Up the Projector
MAINTENANCE
Projecting an Image from the Computer
Projecting an Image from AV Equipment
Useful Functions Available During a Presentation
Setting Up Functions from Menus
Maintenance
Troubleshooting
Appendix
Index
Downloaded From projector-manual.com Canon Manuals
Maintenance
Cleaning the Projector
Clean the projector frequently to prevent dust from settling on the surface.
A dirty lens may ruin the quality of the projected image.
Caution
z The main unit is very hot immediately after turning off the projector. Wait until the projector cools down sufficiently (more than 1 hour) before cleaning the projector. Otherwise, you may get burned or injured.
z Before cleaning the projector, be sure to remove the power plug from the AC outlet.
Otherwise, electric shock or fire may result.
Wipe the projector's main unit softly with a soft cloth.
If the projector is heavily soiled, soak the cloth in water with a small amount of detergent in
it, squeeze the cloth very well, and then wipe the projector with it. After cleaning, wipe the
projector with a dry cloth.
Caution
z Never use volatile cleaning liquid or benzine, as these may damage the finish of the
projector. When using a chemical dust cloth, make sure to read the instructions thoroughly.
z When cleaning the projector's lens, use a commonly available air blower or lens
cleaning paper. The lens surface is easily damaged, so do not use a hard cloth or tissues.
MAINTENANCE
When Not Used for an Extended Period of Time
Be sure to attach the lens cap on the lens and store in the supplied carrying bag.
Downloaded From projector-manual.com Canon Manuals
120
Cleaning and Replacing the Air Filter
An air filter is installed in the air intake vent on the bottom of the main body to protect the
internal lens and mirror from dust. Should the air filter become clogged with dust, the projector may be damaged since it will block the air flow into the projector and raises the internal temperature of the projector.
Caution
z The main unit is very hot immediately after turning off the projector. Wait until the projector cools down sufficiently (more than 1 hour) before cleaning the projector. Otherwise, you may get burned or injured.
z Before cleaning or replacing the air filter, be sure to remove the power plug from the
AC outlet. Otherwise, electric shock or fire may result.
z Do not insert any object into the projector through the air filter opening. You may suffer
electric shock or injury due to the high-voltage parts or rotating parts.
Cleaning the Air Filter
Turn the projector upside down, remove the cover by pushing the latch, remove the air filter, and clean it with a vacuum cleaner.
When cleaning dust off the side exhaust vent and the bottom air intake vent, bring the vacuum cleaner nozzle close to them directly.
z Clean the air filter frequently.
z After cleaning the air filter, install it by following the removal steps 1 to 5 in reverse.
Replacing the Air Filter
1
3
4
5
Filter cover
MAINTENANCE
2
Turn off the projector, remove the power
plug from the AC outlet, and let the projector stand for at least 1 hour.
Air filter
Remove the filter cover by pushing the
position of the arrow.
Push
Remove the air filter.
Install a new air filter.
Install the filter cover securely without any
space.
z
z
z
z
Attach the lens cap when replacing the air filter.
Handle the air filter carefully. If damaged, the air filter will not work appropriately.
Replace the air filter whenever you replace the lamp.
An air filter can be ordered from your dealer.
Downloaded From projector-manual.com Canon Manuals
121
Replacing the Lamp
When the time of use of the lamp exceeds the certain amount of time, the following message (two types) is displayed for 10 seconds every time the projector is turned on.
z If the time of use is:
SX7 MarkII: 1800 to 2000 hours
SX60
: 2400 to 2500 hours
* [<], [>], the [OK] button, and the [POWER]
button are available during this message
is displayed.
z If the time of use is:
SX7 MarkII: 2000 hours or more
SX60
: 2500 hours or more
* The [POWER] button is available during
this message is displayed.
z This message will not be displayed again if you select [Cancel] in response to the message
"Do you want to display this message again?".
z You can check the time of use of the lamp in [Lamp counter] in the [System settings] menu
(P118).
MAINTENANCE
Caution
z When replacing the lamp, turn off the projector, wait until the cooling fan stops,
remove the power plug from the AC outlet, and let the projector stand for at least 1
hour. Otherwise, you may get burned because the main unit is very hot immediately
after the projector is turned off.
z Do not touch the inner glass surface when you replace the lamp. Otherwise, the projector's performance may degrade.
z Make sure to handle the lamp carefully and correctly since it may explode if it is
scratched or shocked.
z Do not remove screws unless specified.
Replacing Lamp
This projector uses the following lamp.
Lamp type No. SX7 MarkII: RS-LP04
SX60
: RS-LP03
z Be sure to use the specified lamp.
z A lamp can be ordered from your dealer or Canon home page.
Downloaded From projector-manual.com Canon Manuals
122
Replacing the Lamp
1
Turn off the projector, disconnect the power
plug from the AC outlet, and then let the projector stand for at least 1 hour.
2
Loosen a screw with a flathead screwdriver
and remove the lamp cover.
Lamp cover
Screw
3
4
Loosen two screws, pull up the handle, and
then remove the lamp.
Screw
Handle
Fully insert a new lamp and secure it with two
screws.
* After the installation, be sure to push down
the handle.
Lamp
Replace the lamp cover and tighten the
screw.
6
7
Turn on the projector.
8
Select [Reset] -> [OK] to reset the lamp
counter.
MAINTENANCE
5
Lamp cover
Bring up the menu and select [System settings] -> [Other settings] -> [Lamp counter]
(P118).
Downloaded From projector-manual.com Canon Manuals
123
Downloaded From projector-manual.com Canon Manuals
Table of contents/Safety Instructions
Before Use
Setting Up the Projector
TROUBLESHOOTING
Projecting an Image from the Computer
Projecting an Image from AV Equipment
Useful Functions Available During a Presentation
Setting Up Functions from Menus
Maintenance
Troubleshooting
Appendix
Index
Downloaded From projector-manual.com Canon Manuals
Troubleshooting
WARNING Lamp Flash Patterns
The WARNING lamp on the Control Panel flashes in red after the projector is turned off
when there is a trouble in the projector.
z Wait until the cooling fan stops and disconnect the power plug from the AC outlet before
dealing with the trouble.
Flash Pattern
Meaning
Countermeasure
TROUBLESHOOTING
One flash
Temperature
abnormality
The temperature inside the projector is too high for some reason or the outside air temperature is higher than the specified
one. If the problem is inside the projector, check whether the
projector is installed and operated normally, unplug the projector from the power outlet to cool down the inside of it and
retry projection. If the air intake or exhaust vent is blocked,
remove the obstacle. If the same warning occurs again, the
projector may be defective. Contact your dealer.
Two flashes
Faulty lamp
The lamp has burnt out. Replace the lamp with a new one. If
the same warning is experienced again, the lamp drive circuit
may be defective. Contact your dealer.
Three flashes
Faulty lamp
cover
The lamp cover is open. Unplug the projector from the power
outlet, then install the lamp cover and turn on the projector
again.
If the lamp cover has been installed properly, the lamp cover
detection switch may be defective. Contact your dealer.
Four flashes
Faulty cooling
fan
The cooling fan or another component may be defective.
Unplug the projector from the power outlet, then plug it to the
outlet and turn on the projector again. Contact your dealer if
the same warning is given.
Five flashes
Faulty power
supply
The abnormal voltage is applied to some parts in the power
supply or any other failure may be occurred. Unplug the projector from the power outlet, then plug it to the outlet and turn
on the projector again. Contact your dealer if the same warning is given.
Six flashes
System failure
Some of the functions may be defective. Turn off the projector
and retry projection. If the same warning is experienced again,
contact your dealer.
Downloaded From projector-manual.com Canon Manuals
126
Symptoms and Solutions
You cannot turn on the projector.
Cause
Countermeasure
The power cord is not connected Check whether the power cord is connected correctly (P40).
correctly.
The power cord has just been connected.
You cannot turn on the projector until the [POWER] indicator
turns red after connecting the power plug (P40).
You attempted to turn on the pro- The projector cannot be turned on for a while after it is turned
jector immediately after turning it off. Wait for a while before pressing the [POWER] button again
(P60).
off.
The safety device has activated You cannot release the safety device. Contact your dealer.
because you put the projector in
the carrying bag during the cooling
fan was rotating.
The safety device is activated You cannot release the safety device for safety reasons. Conbecause the air intake or the tact your dealer.
exhaust vent is blocked and the
internal temperature of the projector is increased.
You cannot project an image from the projector.
Countermeasure
Any connection cable is connected
incorrectly.
Check whether the projector is connected to the computer or
AV equipment correctly (P36, 64).
20 seconds have not passed since
the projector was turned on.
When the projector is turned on, the Opening window is displayed for approximately 20 seconds. To project an image
immediately, press the [OK] button on the remote control or
top control (P40).
No image is sent from the AV Check that an image is played on the connected digital camequipment.
era, video camcorder, DVD, etc.
The wrong video terminal or signal
type is selected.
Check that the correct video terminal and signal type are
selected (P48, 70).
The [NO SHOW] function has been
selected.
Press the [NO SHOW] button on the remote control (P78).
No image is sent due to the problem in the computer.
Turn on the projector and computer in this order again.
Downloaded From projector-manual.com Canon Manuals
127
TROUBLESHOOTING
Cause
You cannot hear sound.
Cause
Countermeasure
The audio cable is not connected Check the cable connection of the audio cable (P38).
correctly.
The [MUTE] function is enabled.
Press the [MUTE] button on the remote control (P79).
The volume level is adjusted to the Press the [VOL+] button on the remote control or top control to
minimum.
adjust the volume level (P79).
An audio cable with a built-in resis- Use an audio cable without a built-in resistor.
tor is used.
The projected image is blur.
Cause
Countermeasure
The image is out of focus.
Adjust the focus (P51).
The lens cap is not removed.
Remove the lens cap.
The distance to the screen is too
short.
Check whether the distance to the screen is appropriate. If the
distance is shorter than approximately 1.2 m (3.9'), the projector cannot focus on the screen (P32, 133).
The projector is not placed straight
in front of the screen.
Check whether the projector is placed obliquely to the screen.
A slight error in the projection angle can be corrected through
the keystone adjustment function (P43, 52).
The projector has been moved to a
place where the temperature varies
a lot.
When the projector is moved from a low-temperature place to
a high-temperature place, condensation may form on the lens.
The condensation will evaporate a while later and the projector will be able to project a normal image.
The lens is stained.
Clean up the lens (P120).
TROUBLESHOOTING
You cannot project an image appropriately.
Cause
Countermeasure
The projected image is inverted in The ceiling mounted/rear projection setting is incorrect. Check
the vertical or horizontal direction.
the [Image flip H/V] setting in the [Display settings] menu
(P97).
Downloaded From projector-manual.com Canon Manuals
128
You cannot project an image from a notebook computer.
Cause
Countermeasure
The connection cable is not con- Check whether the connection cable is connected to the
nected correctly.
video terminal of the computer correctly (P36, 37).
The video signal type is incorrect.
Check whether the selected signal type is correct (P91, 92,
132).
It is not set the external monitor out- Turn on the external monitor output on the notebook computer.
put setting on the notebook cor- To turn on the external monitor output, press the [LCD] or
[VGA] function key or a key with an icon for the external monirectly.
tor while holding down the [Fn] key on the keyboard of the
notebook computer (P45).
The combination of keys used to perform this operation varies
among computer manufacturers. For more detailed information, refer to the User's Manual that came with your computer.
The displayed image is not the
same as that displayed on the
notebook computer.
Check whether the dual screen (multi-display) mode is
selected on the notebook computer.
If the dual screen mode has been selected, change it to the
simultaneous display mode on the notebook computer.
The output setting method varies among computer manufacturers. For more detailed information, refer to the User's Manual that came with your computer.
The projector is forced to be turned off.
Countermeasure
Check whether the air intake or exhaust vent is blocked. If the
air intake or exhaust vent is blocked, the temperature inside
the projector rises and the power is automatically turned off to
protect the projector. Wait until the internal temperature gets
down, and then turn on the projector without blocking the
intake and exhaust vents (P22, 23, 40).
The air filter is dirty.
Check whether the bottom air filter is clogged with dust.
If the air filter is clogged, clean or replace the air filter (P121).
The lamp has exploded (or it is
defective).
Check whether the lamp has exploded.
If the lamp has exploded, replace it. The lamp may be defective if it has not exploded. Check the lamp by replacing it with
a spare lamp if you have one (P13, 122, 123).
The operating temperature is inap- Check whether the operating temperature is 5 to 35°C (P15).
propriate.
Other reasons
The projector may be damaged. Contact your dealer.
Downloaded From projector-manual.com Canon Manuals
129
TROUBLESHOOTING
Cause
The air intake or exhaust vent is
blocked.
You cannot operate the remote control.
Cause
Countermeasure
Batteries are not installed properly
or they have run out.
Check whether batteries are installed correctly. If batteries are
installed correctly, replace them with new batteries (P29).
You are operating the remote con- Check whether you are operating the remote control within the
trol from the outside of the remote remote control operating range.
Also check whether there is any obstacle between the infrared
control operating range.
remote receiver of the projector and the remote control (P29).
You are operating the remote con- Check whether the infrared remote receiver of the projector is
trol under an inappropriate operat- exposed to direct sunlight or strong light of lighting apparatus
(P29).
ing environment.
The channel setting of the remote Check whether the channel setting of the remote control has
control does not match with the set- been changed. You can check the [Remote control] setting in
the [System settings] menu (P115).
ting of the projector.
The key lock function is prohibiting
the remote control operation.
Check whether [Key lock] is enabled to disable the remote
control operation.
In the System settings menu, set [Key lock] to [Off] (P114).
You cannot use the wireless mouse function.
Cause
Countermeasure
The USB cable is not connected Check whether the USB cable is connected between the procorrectly.
jector and computer correctly (P82).
A mouse driver is not installed.
Check whether the mouse is functioning on the computer. If it
is not, install a mouse driver to the computer.
The mouse is not recognized due Turn on the projector and computer in this order again.
to a problem in the computer.
TROUBLESHOOTING
Downloaded From projector-manual.com Canon Manuals
130
Table of contents/Safety Instructions
Before Use
Setting Up the Projector
APPENDIX
Projecting an Image from the Computer
Projecting an Image from AV Equipment
Table of contents for Appendix
Useful Functions Available During a Presentation
Supported Computer Signal Types............ P132
Relationship between Screen Size and
Projecting Distance.................................... P133
Setting Up Functions from Menus
Glossary .................................................... P134
Specifications ............................................ P138
Maintenance
Index.......................................................... P140
Menu Configuration ................................... P144
Troubleshooting
Appendix
Index
Downloaded From projector-manual.com Canon Manuals
Appendix
Supported Computer Signal Types
This projector supports following signal types.
If your computer or AV equipment is compatible with any one of these signal types, the projector's auto PC function select the input signal type to project an image appropriately.
ANALOG PC
DIGITAL PC
Resolution
(dots)
Signal
type
640 x 480
VGA
720 x 400
–
800 x 600
1024 x 768
1280x768
1280x800
(SX7 MarkII)
1360x768
1152 x 864
SVGA
XGA
WXGA
–
–
–
1280 x 960
–
1280 x 1024
SXGA
APPENDIX
1152 x 900
1400 x 1050
SXGA+
1600 x 1200
UXGA
640 x 480 MAC LC 13
640 x 480
MAC 13
832 x 624
MAC 16
1024 x 768
MAC 19
1152 x 870
MAC 21
1280 x 960
MAC
1280 x 1024
MAC
Horizontal frequency (KHz)
31.469
31.469
37.50
37.861
37.861
43.269
31.469
34.50
35.156
37.879
37.898
38.00
38.60
46.875
48.077
53.674
44.028
46.897
47.00
48.363
48.496
56.476
58.032
60.023
60.314
60.994
62.04
63.478
68.677
47.986
Vertical frequency (Hz)
59.94
70.09
75.00
72.81
74.38
85.01
70.09
55.38
56.25
60.32
61.03
60.51
60.31
75.00
72.19
85.06
54.63
58.19
58.31
60.00
60.02
70.07
72.00
75.03
74.92
75.77
77.07
79.35
85.00
59.83
49.702
60.03
47.712
64.196
61.17
61.846
71.399
60.00
62.50
63.337
63.364
63.735
63.791
63.899
63.981
71.694
76.97
79.976
81.135
63.981
75.00
34.967
35.00
49.725
60.248
68.681
75.00
80.00
60.02
70.39
65.28
66.00
75.64
60.00
58.63
59.98
59.95
60.01
60.18
60.00
60.02
67.19
72.00
75.03
76.11
60.02
60.00
66.60
66.67
74.55
75.08
75.06
75.08
75.08
Resolution
(dots)
640 x 480
800 x 600
1024 x 768
1280 x 1024
1400 x 1050
*
Horizontal frequency (KHz)
31.469
37.879
48.363
63.981
63.981
Vertical frequency (Hz)
59.94
60.32
60.00
60.02
60.02
Only for SX7 MarkII/SX60
DIGITAL VIDEO
Signal
type
D-480p
D-575p
D-720p
D-1080i**
D-1080i**
**
Horizontal frequency
(KHz)
31.469
31.250
44.955
28.125
33.716
Vertical frequency
(Hz)
59.94
50.00
59.94
50.00
59.94
Interlaced signal
COMPONENT
Signal
type
480p
480i**
575p
575i**
720p
1035i**
1080i**
Horizontal frequency
(KHz)
31.469
15.734
31.250
15.625
44.955
33.750
28.125
33.716
Vertical frequency
(Hz)
59.94
59.94
50.00
50.00
59.94
60.00
50.00
59.94
**
Interlaced signal
-
The specifications in the table above are subject to change without prior notice.
This projector does not support any computer
signal of which dot clock is 170MHz or higher.
Use a full connected VGA cable in which all
pins are connected; otherwise, an image may
be projected improperly.
-
Downloaded From projector-manual.com Canon Manuals
132
Signal
type
D-VGA
D-SVGA
D-XGA
D-SXGA*
D-SXGA+*
Relationship between Screen Size and Projecting Distance
Screen size at 4:3
aspect ratio
Type – W x D (cm)
Max. zooming
40" 81 x 61
1.2 (3.9')
2.0 (6.6')
55 (1.8')
6 (0.2')
37" 81 x 46
50" 102 x 76
1.5 (4.9')
2.5 (8.2')
69 (2.3')
8 (0.26')
46" 102 x 57
Projecting distance at (m)
H1 (cm)
Min. zooming
H2 (cm)
Screen size at 16:9
aspect ratio
Type – W x D (cm)
60" 122 x 91
1.8 (5.9')
2.9 (9.6')
82 (2.7')
9 (0.3')
55" 122 x 69
70" 142 x 107
2.1 (6.9')
3.4 (11.2')
96 (3.1')
11 (0.36')
64" 142 x 80
80" 163 x 122
2.4 (7.9')
3.9 (12.9')
110 (3.6')
12 (0.4')
74" 163 x 91
90" 183 x 137
2.7 (8.9')
4.4 (14.6')
123 (4.0')
14 (0.46')
83" 183 x 103
100" 203 x 152
3.0 (9.8')
4.9 (16.1')
137 (4.5')
15 (0.49')
91" 203 x 114
110" 224 x 168
3.3 (10.8')
5.4 (17.7')
151 (5.0')
17 (0.5')
101" 224 x 126
120" 244 x 183
3.6 (11.8')
5.9 (19.4')
165 (5.4')
18 (0.59')
110" 244 x 137
130" 264 x 198
3.9 (12.8')
6.4 (21')
178 (5.8')
20 (0.66')
119" 264 x 149
140" 284 x 213
4.2 (13.8')
6.9 (22.6')
192 (6.3')
21 (0.69')
128" 284 x 160
150" 305 x 229
4.5 (14.8')
7.4 (24.2')
206 (6.8')
23 (0.75')
138" 305 x 171
160" 325 x 244
4.8 (15.5')
7.9 (25.9')
219 (7.2')
24 (0.79')
147" 325 x 183
170" 345 x 259
5.1 (16.8')
8.4 (27.4')
233 (7.6')
26 (0.85')
156" 345 x 194
180" 366 x 274
5.4 (17.7')
8.9 (29.2')
247 (8.1')
27 (0.86')
165" 366 x 206
182" 370 x 277
5.4 (17.7')
9.0 (29.5')
250 (8.2')
28 (0.9')
167" 370 x 208
190" 386 x 290
5.6 (18.4')
–
261 (8.6')
29 (0.95')
174" 386 x 217
200" 406 x 305
5.9 (19.4')
–
274 (9.0')
30 (0.98')
184" 406 x 229
210" 427 x 320
6.2 (20.3')
–
288 (9.4')
32 (1.05')
193" 427 x 240
220" 447 x 335
6.5 (21.3')
–
302 (9.9')
34 (1.12')
202" 447 x 251
230" 467 x 351
6.8 (22.3')
–
315 (10.3')
35 (1.15')
211" 467 x 263
220" 488 x 274
240" 488 x 366
7.1 (23.3')
–
329 (10.8')
37 (1.21')
250" 508 x 381
7.4 (24.3')
–
343 (11.3')
38 (1.25')
233" 508 x 286
260" 528 x 396
7.7 (25.3')
–
357 (11.7')
40 (1.31')
239" 528 x 297
270" 549 x 411
8.0 (26.3')
–
370 (12.1')
41 (1.35')
248" 549 x 309
280" 569 x 427
8.3 (27.2')
–
384 (12.6')
43 (1.41')
257" 569 x 320
290" 589 x 442
8.6 (28.2')
–
398 (13.1')
44 (1.44')
266" 589 x 331
300" 610 x 457
8.9 (29.2')
–
411 (13.5')
46 (1.51')
276" 610 x 343
APPENDIX
Downloaded From projector-manual.com Canon Manuals
133
Glossary
* is only applicable to SX7 MarkII
6-axis color adjust (P107)
Aspect (P57, 73, 90)
The color adjustment function for an
advanced user. You can adjust color balance
and color level for 6 axis of RGB (red/green/
blue) and CMY (cyan/magenta/yellow) of the
projected image to make a fine color adjustment. You can perform the 6-axis color
adjustment in the image adjustment menu.
The aspect ratio is the ratio of the horizontal
(longer) dimension to the vertical (shorter)
dimension of a screen. It is expressed as
"longer dimension: shorter dimension." The
following aspect ratio is normally used:
AdobeRGB (P55, 102)
A color space specification set up by Adobe
systems Incorporated which is applied to
high performance digital cameras, displays
and others. You can project an image with
more accurate color reproduction since Its
has wider color gamut than sRGB.
In SX7 MarkII, if you select [AdobeRGB] in
the [Image mode] setting, the projector can
project the best-quality image conforming to
the AdobeRGB Standard. Please be aware
that color of the projected image may vary
with that of the original image if you project
an AdobeRGB compatible image in sRGB
mode or project an sRGB compatible image
in AdobeRGB mode.
Ambient light* (P108)
APPENDIX
Lightning environment around the projector.
You can correct and project an image more
appropriately according to the ambient light
on the screen via the setting of [Ambient
light] if you have selected [Photo] for [Image
mode].
Analog PC (P27, 36, 93)
A signal system used to send analog signal
information of R (red), G (green), and B
(blue). It is a typical system for connecting a
color monitor to a computer. Connect the
analog PC output terminal on the computer
and Input Terminal-1 or Input Terminal-2 on
this projector with a monitor cable. Select
[ANALOG PC-1] for Input Terminal-1 and
[ANALOG PC-2] for Input Terminal-2 at projection.
Downloaded From projector-manual.com Canon Manuals
134
[4:3]
The aspect ratio widely accepted in the standard screen resolution, for example the traditional television screen and VGA (640 x 480)
and XGA (1024 x 768) in PC. The aspect ratio
for this projector is 4:3.
[5:4]
This aspect ratio is used if you select the resolution such as SXGA (1280X1024) in PC.
The shorter dimension in [5:4] is a little longer
than that in [4:3]. An image with aspect ratio
of 5:4 is properly displayed if you select
[Auto] for [Aspect]; however, the margins are
displayed on both sides of the screen.
[16:9]
The aspect ratio for the high definition or
wide-screen. WXGA (1280 x 768 and 1360 x
768) is used as the aspect ratio close to 16:9
for the wide screen monitor in PC. An image
with aspect ratio of 16:9 is properly displayed
if you select [Auto] for [Aspect]; however, the
margins are displayed at the top and bottom
of the screen.
For the aspect ratio for movie screens, "vista
vision size" and "cinema scope size", etc. are
used.
“Vista vision size”
The aspect ratio close to 16:9. Select [Auto]
or [Wide] for [Aspect]. The black belts are
added at the top and bottom of the image.
“Cinema scope size”
The landscape-oriented aspect ratio of 8:3.
Select [Auto] or [Wide] for [Aspect]. The
black belts are added at the top and bottom
of the image.
Color temperature* (P105)
DVI (P37, 48, 65, 70)
A value that represents the related color in a
light source in general. In this projector, the
color temperature is used to adjust the RGB
color balance for the projected image to correct the related color influence by the ambient light. If you increase and decrease the
color temperature, white changes to blue and
red, respectively. You can set the color temperature in the [Color adjustment] menu if
[Photo] has been selected for [Image mode].
A digital video signal connection interface for
a computer and AV equipment. This interface
allows digital data to be transmitted without
converting to analog data, assuring high
image quality with no signal degradation. The
DVI-I (integrated) connector can be used to
transmit both an analog video signal and digital video signal.
Component (P27, 64, 92)
A signal system in which an image is transmitted by being broken down the brightness
signal (Y) and the color signal (C) into the B-Y
color difference signal and the R-Y color difference signal. Its image quality is higher
than that of the composite video. This system
can project a better-quality image as compared with the composite signal system.
Connect the component video terminal on
the AV equipment and the ANALOG IN-2 terminal on this projector with a component
cable. Select [COMPONENT] at projection.
Composite (P27, 66)
Digital PC (P27, 37)
A signal system used to send digital information of individual display dots. This system is
free from deterioration of image quality
because of no analog conversion. Connect
the DVI output terminal on the computer and
Input Terminal-1 on this projector with a DVI
connection cable. Select [DIGITAL PC] at
projection.
Downloaded From projector-manual.com Canon Manuals
A parameter that adjusts the reproduction
range of a brightness signal from black to
white within the image signal to naturally
reproduce it on the screen. The reproducibility of the bright tone is mainly changed. Since
you can adjust the gain for each RGB color in
this projector, you can also adjust colors. The
gain is normally adjusted with the offset.
Gamma Correction (P104, 106)
A tone adjustment system used during projection of image data. The gamma correction
function works effectively when portions of an
image are obscure because they are too light
or dark.
This projector supports manual gamma correction and dynamic gamma correction
which performs the gamma correction automatically.
HDCP
An abbreviation of High-bandwidth Digital
Content Protection which is an encryption
technology for copy protection of digital
image signals. In this projector, you can
project digital contents copy-protected with
the HDCP technology. To project the contents, connect the Input Terminal-1 on the
projector and an HDMI terminal or DVI terminal on an AV equipment with a dedicated
cable, and then select [DIGITAL VIDEO] from
the [INPUT] menu.
135
APPENDIX
A video signal system used to send a brightness signal (Y) and a color signal (C)
together. Connect the composite output
(RCA) terminal on the AV equipment and the
VIDEO IN terminal on this projector with a
video cable. Select [VIDEO] at projection.
Gain (P105)
HDMI (P65, 70)
Resolution (P44, 91)
A digital video signal connection interface for
an AV equipment. Its terminal is more compact than the DVI terminal. It allows to transmit video and audio signals simultaneously.
The number of dots (horizontal dots x vertical
dots) that can be displayed on a computer is
called “resolution of display”. Resolution indicates the size of the display area (amount of
information).
Memorized Color Correction (P107)
A memorized color is a color in our memory.
The memorized color such as blue for the sky
is more vivid than the real color, so you may
feel colors of a projected image are dull. If
such is the case, enable the memorized color
correction function to make the colors close
to the ones in our memory. You can enable
the memorized color correction function in
the image adjustment menu.
Offset (P105)
A parameter that shifts the reproduction
range of a brightness signal from black to
white within an image signal toward the
higher or lower level of brightness. The reproducibility of the dark tone is mainly changed.
Since you can adjust the offset for each RGB
color in this projector, you can also adjust
colors. The offset is normally adjusted with
the gain.
Progressive (P96)
APPENDIX
An image display system used to display the
entire screen per scan. For an interlace signal (video signal) that displays one screen by
two scans (one for odd lines and one for
even lines) is input, progressive processing
is required. When the progressive function is
turned off, one screen is displayed using
image signals per interlace signal, deteriorating the vertical resolution of the image. When
the progressive function is turned on, one
screen is displayed using image signals per
two interlace signals, improving the vertical
resolution of the image. Turn off the progressive function when flickering and horizontal
lines are noticeable on a fast-moving picture.
Downloaded From projector-manual.com Canon Manuals
136
Resolution
VGA
SVGA
XGA
SXGA
SXGA+
UXGA
Number of dots
HoriVertical
zontal
640
800
1024
1280
1400
1600
480
600
768
1024
1050
1200
Number of pixels in each
resolution
If you select SXGA+ (1400 dots x 1050 dots)
as the display resolution for the connecting
computer, this projector can project high-resolution images. If your computer does not
have the SXGA+ option, select the maximum
resolution among the selectable options.
sRGB (P55, 102)
An international standard of color representation (color space) which is applied to general
digital cameras, displays and others. In this
projector, if you select [sRGB] in the [Image
mode] setting, the projector can project the
best-quality image conforming to the sRGB
Standard.
S-video (P27, 66, 92)
A signal system (YC separation signal) used
to send a brightness signal (Y) and color signal (C) separately. Connect the S-video terminal on the AV equipment and the S-VIDEO
IN terminal on this projector with an S-video
cable. Select [S-VIDEO] at projection.
Tracking (P93)
To reproduce an image from an analog
image signal, the process to accumulate
image information at the appropriate timing
with reference to the synchronization signal
within the image signal. This process is
called the tracking. This projector can display an image properly by automatically
adjust the tracking with the auto PC adjustment function even if there is a small difference in the synchronization signal from an
analog imaging device.
Video (P27, 66, 92)
An output terminal widely used in an AV
equipment. It is also called as a composite
output terminal (pin terminal or RCA terminal). For more details, refer to "Composite".
APPENDIX
Downloaded From projector-manual.com Canon Manuals
137
Specifications
Projector
Video signals
Projection
lens
Display
device
Model name
Display system
Optical system
Type
Size/Aspect rat
Drive system
Number of pixels/
Total Number of pixels
Zoom ratio/Focal length/F value
Zooming and focusing system
Lens shift
Light source
Screen size (projection distance)
Number of reproducible colors
Brightness
Contrast ratio
Uniformity
Speaker
Maximum input resolution
ANALOG PC input
Input terminals
DIGITAL PC input
COMPONENT input
RGB SCART input
DIGITAL VIDED input
VIDEO/S-VIDEO input
Input Terminal-1
Input Terminal-2
VIDEO IN terminal
S-VIDEO IN terminal
AUDIO IN terminal
USB terminal
SERVICE PORT
Video Output terminal
Audio Output terminal
Digital PC
Input signals
Analog PC
Video
APPENDIX
Audio
Noise (Lamp mode: Normal/Quiet)
Operating temperature
Power supply
Power consumption (Lamp mode:
Normal/Quiet, standby state)
Dimensions
Weight
SX7 MarkII/SX60
RGB liquid crystal system
Color separation by dichroic mirror/polarizing beam splitter and color composition by prism
Reflective liquid crystal panel
0.7" x 3 panels/4 : 3
active matrix system
SX7 MarkII/SX60: 1,470,000 (1400 x 1050) x 3 panels/4,410,000
1.7x/f=21.7 to 35.8 mm/F1.85 to F2.5
Electronic operation/electronic operation (with auto focusing function)
9 : 1 (fixed)
SX7 MarkII: 275W high-pressure lamp, SX60: 180W high-pressure lamp
40" to 300" (1.2 to 9 m)
16,770,000 colors (full color)
SX7 MarkII: 4000 lm, SX60: 2500 lm
1000:1 (full white : full black)/2000:1 (SX60 in Home Cinema mode)
88%
1W monaural x 1
1600 x 1200 dots (compression)
UXGA/SXGA+/WXGA/SXGA/XGA/SVGA/VGA
(scan rate: horizontal: 15 to 100KHz, vertical 50 to 100Hz)
SX7 MarkII/SX60: SXGA+/SXGA/XGA/SVGA/VGA
1080i, 1035i, 720p, 575i, 575p, 480i, 480p
575i
1080i, 720p, 575p, 480p
NTSC, PAL, SECAM, NTSC4.43, PAL-M, PAL-N
Digital PC, analog PC, digital video (DVI-I connector 29-pin)
Analog PC, component, SCART (mini D-sub 15-pin)
composite (RCA)
S-Video (mini DIN 4-pin)
Audio signal (SX7 MarkII: stereo mini jack x 3, SX60: stereo mini jack x 1)
For mouse control (USB type B)
RS-232C (mini DIN 8-pin)
Analog PC (mini D-sub 15-pin)
Audio signal (SX7 MarkII: stereo mini jack)
TMDS (Transition Minimized Differential Signaling)
0.7Vp-p, positive polarity, impedance = 75Ω
Horizontal/vertical synchronization: TTL level, negative or positive polarity
Composite synchronization in G signal: 0.3Vp-p, negative polarity, impedance = 75Ω
Video:1Vp-p, negative synchronization, impedance = 75Ω
S-video: Separate YC signal, Y: 1Vp-p, negative synchronization, impedance = 75Ω
C: 0.286Vp-p (burst signal), impedance = 75Ω
Component: Separate Y Cb/Pb Cr/Pr signal
Y: 1Vp-p, Negative synchronization, impedance = 75Ω
Cb/Pb: 0.7Vp-p, impedance = 75Ω
Cr/Pr: 0.7Vp-p, impedance = 75Ω
142mVrms, impedance = 47 KΩ or more
SX7 MarkII: 35/31 db, SX60: 30/27 db
5 °C to 35 °C
AC 100 – 240 V, 50/60 Hz
SX7 MarkII: 360W/290W, 7W,
SX60: 250W/225W, 7W
266 (W) x 114 (H) x 336 (D) mm / 10.6 (W) x 4.6 (H) x 13.4 (D) in (excluding protrusions)
SX7 MarkII: 4.8 kg/10.6 lbs, SX60: 4.6 kg/10.1 lbs
Remote control, batteries for remote control, power cord, computer connection cable, USB
Accessories
cable, component cable, carrying bag, lens cover, string for lens cover, User's Manual and
Warranty Card.
* 99.99% or more of the LCD panel pixels are effective. During projection, 0.01% or less of pixels may stay lit or unlit due to the characteristics of the LCD panel.
* Using the projector continuously for an extended period of time may accelerate the deterioration of optical parts.
Remote Control
Power supply
Operating range
Dimensions
Weight (not including batteries)
Two 3.0 V, AAA-size batteries
About 5 m (16.4') (to infrared remote receiver)
42 (W) x 22 (H) x 135 (D) mm / 1.7 (W) x 0.9 (H) x 5.3 (D) in
55 g
Downloaded From projector-manual.com Canon Manuals
138
External View
Screw Holes for
installation of ceilingmount hanger
(M4 x 6)
Mini D-sub 15-pin
1
2
3
4
5
6
7
8
R
G
B
Monitor ID2
Ground (Horizontal sync.)
Ground (R)
Ground (G)
Ground (B)
9
10
11
12
13
14
15
+5 V power
Ground (Vertical sync.)
Monitor ID0
DDC data
Horizontal sync.
Vertical sync.
DDC clock
z The terminal specifications for the analog PC-2 input and component input are the same.
Downloaded From projector-manual.com Canon Manuals
139
APPENDIX
Input terminal-2 (ANALOG IN-2) (Analog PC-2 input/component input terminal)
This terminal is used as a computer analog PC input or component input terminal. Use a Dsub computer cable for connection.
Index
Numerics
6-axis color adjust ........................ 107, 134
DVI ........................................... 37, 65, 135
Dynamic gamma .................................. 106
A
E
Adjusting keystone distortion ................. 52
AdobeRGB ............................. 56, 102, 134
Air filter ................................................. 121
Ambient light (SX7 MarkII) ................... 108
ANALOG IN-1 .................................. 26, 36
ANALOG IN-2 ............................ 26, 36, 64
Analog PC ................................ 36, 48, 134
Aspect ................................ 57, 73, 90, 134
AUDIO IN terminal (SX60) ...................... 39
AUDIO IN terminal
(SX7 MarkII) .................................. 38, 67
AUDIO OUT terminal
(SX7 MarkII) ........................................ 68
Auto focus ...................................... 46, 111
Auto input ....................................... 46, 111
Auto keystone ................................ 46, 111
AUTO PC ................................................ 54
Auto screen color ........................... 46, 111
AUTO SET ........................................ 47, 70
Auto setup ................................ 46, 70, 111
External monitor ..................................... 38
B
Beep ..................................................... 112
Brightness ............................................ 103
C
INDEX
Carrying bag .................................... 14, 21
Ceiling mounted ............................... 33, 97
Channel setting .................................... 115
Color adjustment .................................. 105
Color temperature (SX7 MarkII) ........... 105
Component .................................... 64, 135
Composite ............................................ 135
Contrast ................................................ 103
D
D.ZOOM ................................................. 81
DIGITAL IN ....................................... 26, 65
DIGITAL PC ...................................... 37, 48
Digital PC ............................................. 135
Digital video ......................................... 116
Direct power on .................................... 112
Display settings menu ...................... 86, 90
Displaying a logo (SX60) ............... 99, 100
F
Factory defaults ........................... 110, 117
FOCUS ................................................... 51
Focusing ................................................ 51
FREEZE .................................................. 78
G
Gain .............................................. 105, 135
Gamma correction ....................... 104, 135
Guide ................................................... 114
H
HDCP ................................................... 135
HDMI .............................................. 65, 136
Horizontal pixels ..................................... 95
Horizontal position ................................. 94
I
IMAGE .................................................... 55
Image adjustment menu ................ 86, 102
Image flip H/V (Ceiling mounted/Rear) .. 97
Image mode ......................................... 102
Image mode (quality) ..................... 55, 102
INPUT ............................................... 48, 71
Input signal select (AV equipment) ........ 70
Input signal select (computer) ............... 48
Input signal select
(Display settings menu) ...................... 91
Input terminal ......................................... 26
Input terminal (for AV equipment) .......... 64
Input terminal (for computer) ................. 36
K
Key lock ............................................... 114
KEYSTONE ............................................. 52
L
Lamp counter ....................................... 118
Lamp mode .......................................... 109
Lamp replacement ............... 118, 122, 123
LED illumination ................................... 115
Lens cap ................................................ 21
Logo capture (SX60) .............................. 98
Logo position (SX60) .............................. 99
Downloaded From projector-manual.com Canon Manuals
140
M
S
Mem. color correct ............................... 107
Memorized color correction ................. 136
Menu ...................................................... 86
Menu configuration .............................. 144
Menu position ......................................... 96
Mouse operation .................................... 82
MUTE ..................................................... 79
Screen aspect .......................... 59, 74, 101
Screen color ........................................... 98
Screen mode (Aspect) ..................... 57, 73
Screen size .......................................... 133
Selecting a display language ........ 41, 113
Sharpness ............................................ 104
Signal type ........................................... 132
SPOT ...................................................... 83
Spotlight ................................................. 83
sRGB ...................................... 56, 102, 136
S-VIDEO ......................................... 66, 137
Switching to external monitor
(Preparing the notebook computer) ... 45
System settings menu .................... 86, 111
N
NO SHOW ...................................... 78, 100
No signal screen .................................... 99
O
Offset ............................................ 105, 136
Output resolution
(Preparing the computer) ................... 44
P
PAGE ...................................................... 80
Page Up/Down ....................................... 80
Password settings ................................ 116
POWER indicator ................................... 28
Power management ............................... 61
Power management mode (setting) ..... 111
Progressive .................................... 96, 136
Projection distance ........................ 32, 133
Projector installation ......................... 14, 33
Projector on .......................................... 100
P-TIMER ................................................. 80
T
Top control ............................................. 25
Total dots ............................................... 93
Tracking ......................................... 93, 137
V
Vertical pixels ......................................... 95
Vertical position ...................................... 94
Video .................................................... 137
VOL ........................................................ 79
Volume adjustment ................................ 79
W
WARNING lamp ............................. 28, 126
R
Z
Rear projection ................................. 33, 97
Register password ............................... 117
Remote control ......................... 24, 29, 115
Reset ............................................ 110, 117
Resolution ...................................... 57, 136
ZOOM .................................................... 42
Zoom (image size) ................................. 42
Zooming ................................................. 81
INDEX
Downloaded From projector-manual.com Canon Manuals
141
Options
z Replacement lamp
Part No.:
SX7 MarkII: RS-LP04
SX60: RS-LP03
z Ceiling-mount hanger
Part No.: RS-CL07
z Ceiling-mount pipe
(35 cm/13.8 in to 55 cm/21.7 in)
Part No.: RS-CL08*
z Ceiling-mount pipe
(55 cm/21.7 in to 95 cm/37.4 in)
Part No.: RS-CL09*
z DVI digital cable
Part No.: LV-CA29
z SCART cable
Part No.: LV-CA31
z Network adapter
Part No.: RS-NA01 (SX60)
* This part is used to hang the projector from a ceiling.
For more detailed information, refer to the instruction manual that comes with the ceiling-mount hanger
RS-CL07.
Downloaded From projector-manual.com Canon Manuals
142
Downloaded From projector-manual.com Canon Manuals
143
Menu Configuration
The Display settings menu
Aspect
Input signal select
DIGITAL PC/ANALOG PC
Full screen *
4:3
Auto
Wide
True size
VIDEO/S-VIDEO/SCART
Full screen *
4:3
Wide
DIGITAL VIDEO/COMPONENT
Auto *
Full screen
4:3
Wide
P90
ANALOG PC
640 x 480
P91
Menu position
P96
Screen color
Normal *
Greenboard
Adjust Red/Green/Blue
P98
Image flip H/V
None *
Ceiling mounted
Rear
Rear, Ceiling mounted
P97
P91
P90
User screen settings
...
1280 x 1024
VIDEO/S-VIDEO
Auto *
NTSC
PAL
SECAM
NTSC4.43
PAL-M
PAL-N
COMPONENT
Auto *
1080i
1035i
720p
575p
480p
575i
480i
SCART
575i
Input signal settings
Progressive
ANALOG PC
Total dots
Tracking
Horizontal position
Vertical position
Horizontal pixels
Vertical pixels
COMPONENT/VIDEO/
S-VIDEO
Off
On
Auto *
OK/Cancel
P98
Logo position (SX60)
Upper L
Upper R
Center *
Lower L
Lower R
P99
No signal screen
Black
Blue *
User logo (SX60)
P99
NO SHOW
Black *
Blue
User logo (SX60)
P100
Projector on
Canon logo *
Skip
User logo (SX60)
P100
4:3
16:9
16:9 D. image shift
P101
P92
P92
Return
Screen aspect
P92
P93
P93
P94
P94
P95
P95
P96
* Factory defaults (settings after reset)
** You can set this if you have selected [Photo]
for [Image mode].
***SX7 II: It is available if the input signal is
[DIGITAL VIDEO], [COMPONENT], [VIDEO] or
[S-VIDEO].
Downloaded From projector-manual.com Canon Manuals
144
Logo capture (SX60)
The Image adjustment menu
The System settings menu
Image mode
Auto setup
DIGITAL PC/ANALOG PC P102
Photo (SX7 II)
COMMON
Standard *
Presentation
Movie***
Home Cinema (SX60)
AdobeRGB (SX7 II)
sRGB
Brightness
Contrast
Sharpness
Gamma
P103
P103
P104
P104
Color adjustment
COMPONENT/VIDEO/ P106
S-VIDEO
Color level
Color balance
DIGITAL PC/ANALOG PC P105
Color temperature**
(SX7 II)
COMMON
P105
R Gain
R Offset
G Gain
G Offset
B Gain
B Offset
P111
Auto focus
Off
On *
Auto keystone
Off
On *
Auto input
Off
On *
Auto screen color
Off *
On
Return
Power management mode
Off *
Standby
Exit
P111
Direct power on
Off *
On
P112
Beep
Off
On *
P112
Key lock
Off *
Main unit
Remote control
P114
Language
English
Germany
French
Italian
Spanish
Portuguese
Swedish
Russian
Dutch
Finnish
Norwegian
Guide
Off
On *
P114
LED illumination
Off
On *
P115
Remote control
Ch1
Ch2
P115
Digital Video
F*
L
P116
Password settings
Off *
On
P116
Advanced adjustment
Dynamic gamma
Off *
On
P106
Mem. color correct
Off *
L
M
H
P107
6-axis color adjust
Off *
Adjust
P107
Hue/Saturation
Return
DIGITAL PC/ANALOG PC
Ambient light** (SX7 II)
P108
Other settings
Off
Adjust
Type
Tungsten
Fluorescent
Fluorescent H
Level
L
M
H
Lamp mode
Normal
Quiet
P109
Reset
OK/Cancel
P110
P113
Turkish
Polish
Hungarian
Czech
Danish
Chinese
(Simplified)
Chinese
(Traditional)
Korean
Japanese
Register password
Password input
P117
Lamp counter
Return
Reset (OK/Cancel)
P118
Factory defaults
OK/Cancel
P117
Return
Downloaded From projector-manual.com Canon Manuals
145
CANON INC.
30-2, Shimomaruko 3-chome, Ohta-ku, Tokyo
146-8501, Japan
U.S.A.
CANON U.S.A. INC.
One Canon Plaza, Lake Success, NY 110421198, U.S.A.
For all inquires concerning this product, call toll
free in the U.S.
1-800-OK-CANON
CANADA
CANON CANADA INC. HEADQUARTERS
6390 Dixie Road, Mississauga, Ontario L5T
1P7, Canada
CANON CANADA INC. MONTREAL BRANCH
5990, Côte-de-Liesse, Montréal Québec H4T
1V7, Canada
CANON CANADA INC. CALGARY OFFICE
2828, 16th Street, N.E. Calgary, Alberta T2E
7K7, Canada
For all inquiries concerning this product, call toll
free in Canada
1-800-OK-CANON
EUROPE, AFRICA & MIDDLE EAST
CANON EUROPE LTD.
3 The Square, Stockley Park, Uxbridge, Middlesex, UB11 1ET United Kingdom
CANON EUROPA N.V.
Bovenkerkerweg 59-61, 1185 XB Amstelveen,
The Netherlands
CANON FRANCE S.A.S
17, quai du President Paul Doumer, 92414
Courbevoie Cedex, France
CANON UK LTD.
Woodhatch Reigate Surrey RH2 8BF, United
Kingdom
CANON DEUTSCHLAND GmbH
Europark Fichtenhain A10, 47807 Krefeld, Germany
CANON ITALIA S.p.A.
Via Milano 8 I-20097 San Donato Milanese, Milano, Italy
CANON Schweiz AG
Geschäftsbereich Wiederverkauf, Industriestrasse 12, CH-8305 Dietlikon,
Switzerland
CANON GMBH
Zetschegasse 11, A-1230 Wien, Austria
CANON España, S.A.
Av. De Europa, 6 Alcobendas 28108 Madrid, Spain
Downloaded From projector-manual.com Canon Manuals
CANON PORTUGAL S.A.
Rua Alfredo da Silva, 14 Alfragide 2610-016
Amadora, Portugal
CANON Belgium N.V./S.A.
Berkenlaan 3, 1831 Diegem (Mechelen), Belgium
CANON Netherland NV
Neptunusstraat 1, 2132 JA Hoofddorp, The
Netherlands
CANON LUXEMBOURG S.A.
Rue des Joncs 21, L-1818 Howald, Luxembourg
CANON DANMARK A/S
Knud Hoejgaards Vej 1 DK-2860 Soeborg, Danmark
CANON OY
Huopalahdentie 24 PL 1 00351 Helsinki, Finland
CANON SVENSKA AB
Gustav III:s Boulevard 26 169 88 Solna, Sweden
CANON NORGE as
Hallagerbakken 110, Postboks 33, Holmlia,
1201 Oslo, Norway
CENTRAL & SOUTH AMERICA
CANON LATIN AMERICA, INC.
703 Waterford Way, Ste. 400 Miami, FL 33126,
U.S.A.
ASIA
CANON (China) Co., Ltd.
15F Jinbao Building No.89 Jinbao Street,
Dongcheng District, Beijing 100005, China
CANON HONGKONG CO., LTD.
19/F., The Metropolis Tower, 10 Metropolis
Drive, Hunghom, Kowloon, Hong Kong
CANON SINGAPORE PTE. LTD.
1 HarbourFront Avenue, #04-01 Keppel Bay
Tower, Singapore 098632
CANON KOREA CONSUMER IMAGING INC.
Gangnam Finance Center 17F,737,YeoksamDong, Gangnam-gu, Seoul, 135-984, Korea
OCEANIA
CANON AUSTRALIA PTY. LTD.
1 Thomas Holt Drive, North Ryde, N.S.W. 2113,
Australia
CANON NEW ZEALAND LTD.
Akoranga Business Park, Akoranga Drive,
Northcote, Auckland, New Zealand
©CANON INC.2010