www.proform.com
Model No. PFEL06611.0
Serial No.
Write the serial number in the
space above for reference.
Serial
Number
Decal
QUESTIONS?
If you have questions, or if parts are
damaged or missing, DO NOT
CONTACT THE STORE; please
contact Customer Care.
IMPORTANT: Please register this
product (see the limited warranty
on the back cover of this manual)
before contacting Customer Care.
1-888-533-1333
CALL TOLL-FREE:
Mon.–Fri. 6 a.m.–6 p.m. MT
Sat. 8 a.m.–4 p.m. MT
ON THE WEB:
www.proformservice.com
CAUTION
Read all precautions and instructions in this manual before using
this equipment. Keep this manual
for future reference.
USERʼS MANUAL
TABLE OF CONTENTS
WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
HOW TO USE THE ELLIPTICAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
MAINTENANCE AND TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
EXERCISE GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
PART LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
EXPLODED DRAWING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
WARNING DECAL PLACEMENT
This drawing shows the location(s)
of the warning decal(s). If a decal is
missing or illegible, see the front
cover of this manual and request
a free replacement decal. Apply
the decal in the location shown.
Note: The decal(s) may not be
shown at actual size.
PROFORM is a registered trademark of ICON IP, Inc.
2
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of serious injury, read all important precautions and
instructions in this manual and all warnings on your elliptical before using your elliptical. ICON
assumes no responsibility for personal injury or property damage sustained by or through the use of
this product.
1. Before beginning any exercise program,
consult your physician. This is especially
important for persons over age 35 or
persons with pre-existing health problems.
9. The elliptical should not be used by persons
weighing more than 275 lbs. (125 kg).
3. It is the responsibility of the owner to ensure
that all users of the elliptical are adequately
informed of all precautions.
11. Hold the handlebars or the upper body arms
when mounting, dismounting, or using the
elliptical.
10. Wear appropriate clothes while exercising;
do not wear loose clothes that could become
caught on the elliptical. Always wear athletic
shoes for foot protection while exercising.
2. Use the elliptical only as described in this
manual.
12. The heart rate monitor is not a medical
device. Various factors may affect the
accuracy of heart rate readings. The heart
rate monitor is intended only as an exercise
aid in determining heart rate trends in
general.
4. The elliptical is intended for home use only.
Do not use the elliptical in a commercial,
rental, or institutional setting.
5. Keep the elliptical indoors, away from
moisture and dust. Do not put the elliptical in
a garage or covered patio, or near water.
13. The elliptical does not have a freewheel; the
pedals will continue to move until the
flywheel stops. Reduce your pedaling speed
in a controlled way.
6. Place the elliptical on a level surface, with at
least 3 ft. (0.9 m) of clearance in the front
and rear of the elliptical and 2 ft. (0.6 m) on
each side. To protect the floor or carpet from
damage, place a mat under the elliptical.
14. Keep your back straight while using the
elliptical; do not arch your back.
7. Inspect and properly tighten all parts
regularly. Replace any worn parts
immediately.
15. Over exercising may result in serious injury
or death. If you feel faint or if you experience
pain while exercising, stop immediately and
cool down.
8. Keep children under age 12 and pets away
from the elliptical at all times.
3
BEFORE YOU BEGIN
reading this manual, please see the front cover of this
manual. To help us assist you, note the product model
number and serial number before contacting us. The
model number and the location of the serial number
decal are shown on the front cover of this manual.
Thank you for selecting the revolutionary PROFORM®
STRIDECLIMBER 710 I elliptical. The STRIDECLIMBER 710 I elliptical provides an impressive array
of features designed to make your workouts at home
more effective and enjoyable.
For your benefit, read this manual carefully before
you use the elliptical. If you have questions after
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
Length: 5 ft. 5 in. (165 cm)
Width: 2 ft. 3 in. (69 cm)
Game Controller
Handlebar
Console
Heart Rate Monitor
Water Bottle Holder*
Power Jack
Wheel
Leveling Foot
Pedal
Leveling Foot
*No water bottle is included
4
ASSEMBLY
Assembly requires two persons. Place all parts of the elliptical in a cleared area and remove the packing
materials. Do not dispose of the packing materials until assembly is completed.
Assembly requires the included tool(s) and your own Phillips screwdriver
adjustable wrench
, and rubber mallet
.
,
Use the drawings below to identify small parts. The number in parentheses below each drawing is the key number of the part, from the PART LIST near the end of this manual. The number following the parentheses is the
quantity needed for assembly. Note: Some small parts may have been preassembled. If a part is not in the
hardware kit, check to see if it has been preassembled.
M8 Hex Nylon
Locknut (77)–4
M6 x 14mm
Flat Head
Screw (55)–1
M10 x 22mm x
1.5mm Washer
(63)–2
M6 x 18mm
Screw (57)–6
#8 x 1/2"
Screw (79)–6
M4 x 16mm
Screw (80)–4
M8 x 19mm
Screw (65)–4
#8 x 2"
Screw (68)–4
M10 x 15mm
Screw (71)–2
M8 x 55mm Screw
(61)–4
Barrel Nut (56)–1
M10 x 120mm Screw (58)–2
5
M10 x 27mm
Screw (64)–4
1.
1
To make assembly easier, read the
information on page 5 before you begin
assembling the elliptical.
8
Remove the shipping bracket (not shown)
inserted into the underside of the Frame (1).
Then, remove the two M10 x 120mm Screws
(58) and the shipping bracket (not shown)
attached to the front of the Frame. Discard the
shipping brackets. Do not discard the two M10
x 120mm Screws.
58
8
49
Orient the Stabilizer (49) with the Wheels (8) in
the position shown. While a second person tips
the Frame (1) backward, attach the Stabilizer to
the Frame with the two M10 x 120mm Screws
(58).
1
2. Identify the Right Handlebar (36), which is
marked with an “R” sticker, and orient it as
shown. Attach the Right Handlebar to the Frame
(1) with the Upper Body Cap (34) and three M6
x 18mm Screws (57).
2
Repeat this step to attach the Left Handlebar
(22).
22
1
36
34
57
6
3. Identify the Upright (3) and orient it as shown.
Have a second person hold the Upright near the
top of the Frame (1). Locate the wire tie (see
the inset drawing) in the Upright. Tie the lower
end of the wire tie to the Wire Harness (46).
Next, pull the upper end of the wire tie upward
out of the top of the Upright. Then, untie and
discard the wire tie. Tip: Do not allow the Wire
Harness to fall into the Upright. Use a piece
of tape or an elastic band to hold the Wire
Harness in place until step 4.
3
Wire Tie
46
46
3
65
Tip: Avoid pinching the Wire Harness (46)
during this step. Insert the Upright (3) into the
Frame (1). Attach the Upright with four M8 x
19mm Screws (65).
65
Avoid pinching
the Wire
Harness (46)
during this step
4. While a second person holds the Console (4)
near the Upright (3), connect the console wire to
the Wire Harness (46). Insert the excess wire
downward into the Upright.
4
4
Tip: Avoid pinching the wires during this
step. Attach the Console (4) to the Upright (3)
with four M4 x 16mm Screws (80).
1
Avoid pinching the
wires during this step
Console Wire
3
46
7
80
5. Identify and orient the Ramp (2) as shown.
Tip: Remove the Ramp Cover (not shown)
from the Ramp and set it aside until step 9.
Attach the Ramp to the Frame (1) with four M10
x 27mm Screws (64).
5
1
64
6. Cut and remove the wire tie that holds the Link
Tube (30) inside the left Link Arm (25). Leave
the Link Tube inside the left Link Arm and then
position the Left Pedal Leg (24) and the left Link
Arm as shown.
2
6
Grease
56
Apply a small amount of the included grease to
a Barrel Nut (56). Insert the Barrel Nut through
the indicated holes in the Left Pedal Leg (24)
and the left Link Arm (25). Then, insert the
Barrel Nut through the Link Tube (30) inside the
left Link Arm.
24
Holes
Tighten an M6 x 14mm Flat Head Screw (55)
into the Barrel Nut (56).
8
25
30
55
7. Insert the axle of the Roller (27) through the
right Link Arm (25); make sure that the Roller
is on the inner side of the Link Arm. Attach
the Roller with an M10 x 15mm Screw (71) and
an M10 x 22mm x 1.5mm Washer (63). Tip:
Use a wrench to hold the axle of the Roller
firmly in place while you tighten the Screw
into the axle.
7
Repeat this step to attach the other Roller
(27) to the left Link Arm (25).
25
27
25
63 71
8. Orient a Pedal (26) as shown. Attach the Pedal
to the bracket on the Left Pedal Leg (24) with
two M8 x 55mm Screws (61) and two M8 Hex
Nylon Locknuts (77).
8
26
Repeat this step to attach the other Pedal
(26).
61
26
9
24
77
9. Attach the Ramp Cover (7) to the Ramp (2) with
six #8 x 1/2" Screws (79).
9
7
79
79
79
79
2
10. While a second person tips the Frame (1) forward, tighten a Foot (9) into the underside of the
Frame.
10
1
9
10
11. While a second person tips the elliptical forward,
attach the Rear Ramp Cover (17) to the Ramp
(2) with four #8 x 2" Screws (68).
11
17
68
2
68
12. Make sure that all parts of the elliptical are properly tightened. Note: Some hardware may be left over
after assembly is completed. To protect the floor or carpet from damage, place a mat under the elliptical.
Plug the power supply into the socket at the front of the elliptical (see HOW TO PLUG IN THE POWER
SUPPLY on page 12). IMPORTANT: If the elliptical has been exposed to cold temperatures, allow it to
warm to room temperature before plugging in the power cord. If you do not do this, the console displays or other electronic components may become damaged.
11
HOW TO USE THE ELLIPTICAL
HOW TO PLUG IN THE POWER SUPPLY
HOW TO EXERCISE ON THE ELLIPTICAL
Plug one end of the included power supply into the
jack on the front of the elliptical (see the drawing on
page 4 for the location of the jack). Plug the other end
of the power supply into an appropriate outlet that is
properly installed in accordance with all local codes
and ordinances.
To mount the elliptical, hold the handlebars and step
onto the pedal that is in the lower position. Then, step
onto the other pedal. Push the pedals until they begin
to move with a continuous motion. Note: The crank
arms can turn in either direction. It is recommended that you turn the crank arms in the direction
shown by the arrow below; however, for variety,
you can turn the crank arms in the opposite
direction.
Note: The console can also be operated with four 1.5V
“D” batteries (not included); alkaline batteries are recommended. IMPORTANT: If the elliptical has been
exposed to cold temperatures, allow it to warm to
room temperature before inserting batteries into
the Console. If you do not do this, the console
displays or other electronic components may
become damaged. To insert batteries into the console, remove the two screws, which are marked with
a battery symbol, from the back of the console, and
remove the battery cover. Insert four batteries into the
console. Orient the batteries as shown by the markings inside the battery compartment. Then, reattach
the battery cover.
Handlebars
HOW TO MOVE THE ELLIPTICAL
Due to the size and weight of the elliptical, moving it requires two persons. Stand in front of the
elliptical, hold the upright, and place one foot against
one of the front wheels. Pull on the upright and have
a second person lift the rear of the track until the elliptical will roll on the front wheels. Carefully move the
elliptical to the desired location, and then lower it to
the floor.
Pedals
Crank
Arm
To dismount the elliptical, wait until the pedals come to
a complete stop. Note: The elliptical does not have
a free wheel; the pedals will continue to move until
the flywheel stops. When the pedals are stationary,
step off the higher pedal first. Then, step off the lower
pedal.
Pull on
upright
Lift here
HOW TO LEVEL THE ELLIPTICAL
Place
your foot
here
If the elliptical rocks slightly on your floor during use,
turn one or both of the leveling feet beneath the base
or beneath the front stabilizer until the rocking motion
is eliminated. If the elliptical flexes during use, turn the
leveling foot beneath the center of the frame.
Lift
here
12
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of serious injury, read all important precautions and
instructions in this manual and all warnings on your elliptical before using your elliptical. ICON
assumes no responsibility for personal injury or property damage sustained by or through the use of
this product.
1. Before beginning any exercise program,
consult your physician. This is especially
important for persons over age 35 or
persons with pre-existing health problems.
9. The elliptical should not be used by persons
weighing more than 275 lbs. (125 kg).
3. It is the responsibility of the owner to ensure
that all users of the elliptical are adequately
informed of all precautions.
11. Hold the handlebars or the upper body arms
when mounting, dismounting, or using the
elliptical.
10. Wear appropriate clothes while exercising;
do not wear loose clothes that could become
caught on the elliptical. Always wear athletic
shoes for foot protection while exercising.
2. Use the elliptical only as described in this
manual.
12. The heart rate monitor is not a medical
device. Various factors may affect the
accuracy of heart rate readings. The heart
rate monitor is intended only as an exercise
aid in determining heart rate trends in
general.
4. The elliptical is intended for home use only.
Do not use the elliptical in a commercial,
rental, or institutional setting.
5. Keep the elliptical indoors, away from
moisture and dust. Do not put the elliptical in
a garage or covered patio, or near water.
13. The elliptical does not have a freewheel; the
pedals will continue to move until the
flywheel stops. Reduce your pedaling speed
in a controlled way.
6. Place the elliptical on a level surface, with at
least 3 ft. (0.9 m) of clearance in the front
and rear of the elliptical and 2 ft. (0.6 m) on
each side. To protect the floor or carpet from
damage, place a mat under the elliptical.
14. Keep your back straight while using the
elliptical; do not arch your back.
7. Inspect and properly tighten all parts
regularly. Replace any worn parts
immediately.
15. Over exercising may result in serious injury
or death. If you feel faint or if you experience
pain while exercising, stop immediately and
cool down.
8. Keep children under age 12 and pets away
from the elliptical at all times.
3
HOW TO USE THE MANUAL MODE
The lower left corner of the display will show
the distance, in total revolutions, you have
pedaled.
Note: If there is a sheet of clear plastic on the face
of the console, remove the plastic.
The upper right corner of the display will show
the approximate number of calories you have
burned. The upper right corner of the display will
also show your heart rate when you use the handgrip heart rate monitor (see step 5 on page 15).
1. Begin pedaling or press any button on the console to turn on the console.
A moment after you begin pedaling or press a button, the display will turn on.
The lower right corner of the display will show
your pedaling pace in revolutions per minute
(rpm).
2. Select the manual mode.
Each time you turn
on the console,
the manual mode
will be selected. If
you have selected
a workout, reselect
the manual mode
by pressing either of the Workouts buttons repeatedly until the word MANUAL appears in the lower
left corner of the display.
The center of the display will show the resistance level of the pedals for a few seconds each
time the resistance level changes.
You can also view selected information at a larger
size. Press the Display Mode button repeatedly to
view time and distance information, time and calorie information, or time and pace information.
Press the Display Mode button again to view all
information.
3. Change the resistance of the pedals as
desired.
To adjust the volume level of the console, press
the increase and decrease buttons located next to
the Enter button. There are five volume levels.
As you pedal,
change the resistance of the pedals by pressing
any of the
Resistance
increase and
decrease buttons. Note: After you press the buttons, it will take a moment for the pedals to reach
the selected resistance level.
The console has three backlight options. The “On”
option keeps the backlight on while the console is
on. To conserve the batteries, the “Auto” option
keeps the backlight on only while you are pedaling. The “Off” option turns the backlight off. To
select a backlight option, first press and hold down
the Display Mode button for several seconds.
Next, press the Resistance increase button to
select the desired backlight option. Then, press
the Display Mode button to save your selection.
4. Follow your progress with the display.
The upper left corner of the display will show
the elapsed time. Note: When a workout is selected, the display will show the time remaining in the
workout instead of the elapsed time.
14
5. Measure your heart rate if desired.
If the display does not show your heart rate, make
sure that your hands are positioned as described.
Be careful not to move your hands excessively or
to squeeze the contacts too tightly. For optimal
performance, clean the contacts using a soft cloth;
never use alcohol, abrasives, or chemicals to
clean the contacts.
If there are
sheets of plastic
Contacts
on the metal contacts on the
handgrip heart
rate monitor,
remove the plastic. To measure
your heart rate,
hold the handgrip
heart rate monitor
with your palms
resting against the
contacts. Avoid moving your hands or gripping
the contacts too tightly.
6. When you are finished exercising, the console
will turn off automatically.
If the pedals do not move for several seconds, a
tone will sound and the console will pause. If the
pedals do not move for several minutes and the
buttons are not pressed, the console will turn off
and the display will be reset.
When your pulse is detected, one, two, or three
dashes will appear in the display, and then your
heart rate will appear. For the most accurate heart
rate reading, hold the contacts for at least 15 seconds. Note: If you continue to hold the handgrip
heart rate monitor, the display will show your heart
rate for up to 30 seconds.
15
HOW TO USE A WEIGHT LOSS WORKOUT
As you exercise,
you will be prompted to keep your
pedaling pace near
the target rpm setting for the current
segment. When an
upward-pointing arrow appears in the display,
increase your pace. When a downward-pointing
arrow appears in the display, decrease your pace.
When no arrows appear, maintain your current
pace.
1. Begin pedaling or press any button on the console to turn on the console.
A moment after you begin pedaling or press a button, the display will turn on.
2. Select a weight loss workout.
To select one of
Profile
the four weight
loss workouts,
press the Weight
Loss Workouts
button repeatedly
until the name of
the desired workout appears in the display. The workout time and a
profile of the resistance levels for the workout will
also appear in the display.
IMPORTANT: The target rpm settings are
intended only to provide motivation. Your actual pace may be slower than the target rpm settings. Make sure to pedal at a pace that is comfortable for you.
If the resistance level for the current segment is
too high or too low, you can manually override the
setting by pressing the Resistance buttons.
IMPORTANT: When the current segment of the
workout ends, the pedals will automatically
adjust to the resistance level programmed for
the next segment.
3. Begin pedaling or press the Start button to
start the workout.
Each workout is divided into 20, 30, or 45 oneminute segments. One resistance level and one
target rpm (pace) setting are programmed for each
segment. Note: The same resistance and/or target
rpm setting may be programmed for consecutive
segments.
The workout will continue in this way until the last
segment ends. To stop the workout at any time,
stop pedaling. A tone will sound and the time will
begin to flash in the display. To restart the workout,
simply resume pedaling.
The resistance level and the target rpm for the first
segment will appear in the center of the display for
a few seconds. During the workout, the workout
profile will show your progress (see the drawing
above). The flashing segment of the profile represents the current segment of the workout. The
height of the flashing segment indicates the resistance level for the current segment. At the end of
each segment of the workout, a series of tones will
sound and the next segment of the profile will
begin to flash. If a different resistance level and/or
target rpm is programmed for the next segment,
the resistance level and/or the target rpm will flash
in the display for a few seconds to alert you. The
resistance of the pedals will then change.
4. Follow your progress with the display.
See step 4 on page 14.
5. Measure your heart rate if desired.
See step 5 on page 15.
6. When you are finished exercising, the console
will turn off automatically.
See step 6 on page 15.
16
HOW TO USE A CLASSIC WORKOUT
As you exercise,
you will be prompted to keep your
pedaling pace near
the target rpm setting for the current
segment. When an
upward-pointing arrow appears in the display,
increase your pace. When a downward-pointing
arrow appears in the display, decrease your pace.
When no arrows appear, maintain your current
pace.
1. Begin pedaling or press any button on the console to turn on the console.
A moment after you begin pedaling or press a button, the display will turn on.
2. Select a classic workout.
To select one of
Profile
the ten classic
workouts, press
the Classic
Workouts button
repeatedly until
the name of the
desired workout
appears in the display. The workout time and a
profile of the resistance levels for the workout will
also appear in the display.
IMPORTANT: The target rpm settings are
intended only to provide motivation. Your actual pace may be slower than the target rpm settings. Make sure to pedal at a pace that is comfortable for you.
If the resistance level for the current segment is
too high or too low, you can manually override the
setting by pressing the Resistance buttons.
IMPORTANT: When the current segment of the
workout ends, the pedals will automatically
adjust to the resistance level programmed for
the next segment.
3. Begin pedaling or press the Start button to
start the workout.
Each workout is divided into 20 or 30 one-minute
segments. One resistance level and one target
rpm (pace) setting are programmed for each segment. Note: The same resistance and/or target
rpm setting may be programmed for consecutive
segments.
The workout will continue in this way until the last
segment ends. To stop the workout at any time,
stop pedaling. A tone will sound and the time will
begin to flash in the display. To restart the workout,
simply resume pedaling.
The resistance level and the target rpm for the first
segment will appear in the center of the display for
a few seconds. During the workout, the workout
profile will show your progress (see the drawing
above). The flashing segment of the profile represents the current segment of the workout. The
height of the flashing segment indicates the resistance level for the current segment. At the end of
each segment of the workout, a series of tones will
sound and the next segment of the profile will
begin to flash. If a different resistance level and/or
target rpm is programmed for the next segment,
the resistance level and/or target rpm will flash in
the display for a few seconds to alert you. The
resistance of the pedals will then change.
4. Follow your progress with the display.
See step 4 on page 14.
5. Measure your heart rate if desired.
See step 5 on page 15.
6. When you are finished exercising, the console
will turn off automatically.
See step 6 on page 15.
17
HOW TO PLAY THE FAT BLOCKER GAME
Your goal is to
maneuver the
Complete Row
blocks so that they
form a complete
row of black
squares across the
entire arena. Each
time you complete a row of black squares, the row
will disappear, and all blocks above will move
downward one row.
The Fat Blocker game requires quick thinking and fast
reflexes. In addition to the console buttons, you will
use the four-button game controllers on the console to
play the game. Follow the steps below to play the Fat
Blocker game.
1. Begin pedaling or press any button on the console to turn on the console.
A moment after you begin pedaling or press a button, the display will turn on.
As you play, the blocks will fall faster and faster;
however, your pedaling pace will affect the speed
of the blocks—the faster you pedal, the more
slowly the blocks will fall, giving you extra time to
position and orient the blocks. The game will continue until any part of a stacked block reaches the
top of the arena.
2. Select the Fat Blocker game.
To select the Fat Blocker game, press the Fat
Blockers button. The words FAT BLOCKER will
appear at the top of the display.
When the game ends, the display will show your
final score and the level of play that you reached.
The display will then show the four highest scores
recorded since the scores were reset. If desired,
press and hold down the right button on either
controller to reset the scores.
3. Pedal to start the game.
When you start the Fat Blocker game, a game
arena will appear in the center of the display.
If your score is one of the four highest, the display
will prompt you to enter a name consisting of three
letters or digits. While the line below the first letter
is flashing, press the up and down buttons on
either controller to select the desired letter or digit.
Next, press the right button on either controller
and select another letter or digit. Repeat this
process to select a third letter or digit. Then, press
the right button on either controller again. The display will then show the four highest scores recorded since the scores were reset. Note: You can
also use the increase, decrease, and Enter buttons on the console to enter a high score name.
4. Follow your progress with the display.
A block composed of four or five black squares will
slowly move downward until it reaches the bottom
of the arena. Another block will then move downward. There are blocks of eight different shapes.
As each block falls, you can move it to the left or
right using the left and right buttons on the left
controller. In addition, you can rotate the block
counterclockwise or clockwise using the left and
right buttons on the right controller. Once you have
positioned and oriented a block, you can speed its
motion to the bottom of the arena, if desired, by
pressing the down button on either controller.
While you exercise and play the Fat Blocker
game, the corners of the display will show the
elapsed time, the approximate number of calories
you have burned, and your pedaling pace. In addition, the display will show your current score and
the game level that you have reached.
To pause the game, press the Display button. To
resume the game, press the Display button
repeatedly until the words FAT BLOCKER appear
at the top of the display, and then begin pedaling.
5. When you are finished exercising, the console
will turn off automatically.
18
See step 6 on page 15.
HOW TO PLAY THE CALORIE DESTROYER GAME
Between the drones and the laser blaster are five
shields. You can hide the laser blaster below a
shield if desired. However, each time a shield is hit
by a laser, a piece will be vaporized.
The Calorie Destroyer game is a fast-paced game that
pits you against a squadron of laser-firing drones. In
addition to the console buttons, you will use the fourbutton game controllers on the console to play the
game. Follow the steps below to play the Calorie
Destroyer game.
Your goal is to keep the laser blaster from being
hit and to keep any drone from reaching the bottom of the arena. If the laser blaster is hit, it will be
disabled and another laser blaster will appear in its
place; there are a total of four laser blasters. If you
vaporize the entire squadron of drones, a new
squadron will appear.
1. Begin pedaling or press any button on the console to turn on the console.
A moment after you begin pedaling or press a button, the display will turn on.
As you play, the drones will move faster and
faster. The game will continue until all four laser
blasters are disabled or a drone reaches the bottom of the arena.
2. Select the Calorie Destroyer game.
To select the Calorie Destroyer game, press the
Calorie Destroyers button. The word DESTROYER
will appear at the top of the display.
When the game ends, the display will show the
level of play that you reached and your final score.
The display will then show the four highest scores
recorded since the scores were reset. If desired,
press and hold down the right button on either
controller to reset the scores.
3. Pedal to start the game.
When you start the Calorie Destroyer game, a
game arena will appear in the display. Three rows
of drones will begin to move across the top of the
arena, periodically firing their lasers downward.
Each time the drones reach the left or right side of
the arena, they will reverse direction and move
downward.
If your score is one of the four highest, the display
will prompt you to enter a name consisting of three
letters or digits. While the line below the first letter
is flashing, press the up and down buttons on
either controller to select the desired letter or digit.
Next, press the right button on either controller
and select another letter or digit. Repeat this
process to select a third letter or digit. Then, press
the right button on either controller again. The display will then show the four highest scores recorded since the scores were reset. Note: You can
also use the increase, decrease, and Enter buttons on the console to enter a high score name.
4. Follow your progress with the display.
While you exercise and play the Calorie Destroyer
game, the upper left corner of the display will
show the elapsed time. In addition, the display will
show the game level that you have reached and
your current score.
At the bottom of the arena is a laser blaster. You
can fire the laser blaster at the drones by pressing
the up button on either controller. In addition, while
you are pedaling, you can move the laser blaster
to the left or right using the left and right buttons
on either controller. The faster you pedal, the
faster the laser blaster will move.
To pause the game, press the Display button. To
resume the game, press the Display button
repeatedly until the word DESTROYER appears at
the top of the display, and then begin pedaling.
5. When you are finished exercising, the console
will turn off automatically.
See step 6 on page 15.
19
HOW TO USE AN IFIT WORKOUT
A moment after you select a workout, the voice of
a personal trainer will begin guiding you through
your workout. iFit workouts function in the same
way as classic workouts. To use the workout, see
steps 3 to 6 on page 17.
1. Press any button on the console or begin pedaling to turn on the console.
A moment after you begin pedaling or press a button, the display will turn on.
3. When you are finished exercising, remove the
iFit card.
2. Insert an iFit card and select a workout.
Remove the iFit card when you are finished exercising. Store the iFit card in a secure place.
To use an iFit workout, insert an iFit card into the
iFit slot; make sure that the iFit card is oriented so
the metal contacts are face down and are facing
the slot. When the iFit card is properly inserted,
the indicator next to the slot will turn on and words
will appear in the display.
iFit Slot
HOW TO USE THE SOUND SYSTEM
To play music or audio books through the console
sound system while you exercise, plug an audio cable
(not included) into the jack on the console and into a
jack on your MP3 player or CD player; make sure
that the audio cable is fully plugged in.
Next, press the play button on your MP3 player or CD
player. Adjust the volume of the speakers using the
volume control on your MP3 player or CD player.
iFit Card
Next, select the desired workout on the iFit card
by pressing the increase and decrease buttons
next to the iFit slot.
20
MAINTENANCE AND TROUBLESHOOTING
HEART RATE MONITOR TROUBLESHOOTING
Inspect and tighten all parts of the elliptical regularly.
Replace any worn parts immediately.
If the console does not display your heart rate when
you hold the handgrip heart rate monitor, or if the displayed heart rate appears to be too high or too low,
see step 5 on page 15.
To clean the elliptical, use a damp cloth and a small
amount of mild soap. IMPORTANT: To avoid damage
to the console, keep liquids away from the console and keep the console out of direct sunlight.
HOW TO LEVEL THE ELLIPTICAL
BATTERY REPLACEMENT
If the elliptical rocks slightly on your floor during use,
see HOW TO LEVEL THE ELLIPTICAL on page 12.
If the console display becomes dim when the console
is operating with batteries, the batteries should be
replaced; most console problems are the result of low
batteries. IMPORTANT: If the elliptical has been
exposed to cold temperatures, allow it to warm to
room temperature before inserting batteries into
the Console. If you do not do this, the console displays or other electronic components may become
damaged. To replace the batteries, remove the two
screws, which are marked with a battery symbol, from
the back of the console, and remove the battery cover.
Insert four 1.5V “D” batteries into the console. Orient
the batteries as shown by the markings inside the battery compartment. Then, reattach the battery cover.
21
EXERCISE GUIDELINES
WARNING:
Burning Fat—To burn fat effectively, you must exercise at a low intensity level for a sustained period of
time. During the first few minutes of exercise, your
body uses carbohydrate calories for energy. Only after
the first few minutes of exercise does your body begin
to use stored fat calories for energy. If your goal is to
burn fat, adjust the intensity of your exercise until your
heart rate is near the lowest number in your training
zone. For maximum fat burning, exercise with your
heart rate near the middle number in your training
zone.
Before beginning this
or any exercise program, consult your physician. This is especially important for persons
over age 35 or persons with pre-existing
health problems.
The heart rate monitor is not a medical device.
Various factors may affect the accuracy of
heart rate readings. The heart rate monitor is
intended only as an exercise aid in determining heart rate trends in general.
Aerobic Exercise—If your goal is to strengthen your
cardiovascular system, you must perform aerobic
exercise, which is activity that requires large amounts
of oxygen for prolonged periods of time. For aerobic
exercise, adjust the intensity of your exercise until
your heart rate is near the highest number in your
training zone.
These guidelines will help you to plan your exercise
program. For detailed exercise information, obtain a
reputable book or consult your physician. Remember,
proper nutrition and adequate rest are essential for
successful results.
WORKOUT GUIDELINES
EXERCISE INTENSITY
Warming Up—Start with 5 to 10 minutes of stretching
and light exercise. A warm-up increases your body
temperature, heart rate, and circulation in preparation
for exercise.
Whether your goal is to burn fat or to strengthen your
cardiovascular system, exercising at the proper intensity is the key to achieving results. You can use your
heart rate as a guide to find the proper intensity level.
The chart below shows recommended heart rates for
fat burning and aerobic exercise.
Training Zone Exercise—Exercise for 20 to 30 minutes with your heart rate in your training zone. (During
the first few weeks of your exercise program, do not
keep your heart rate in your training zone for longer
than 20 minutes.) Breathe regularly and deeply as you
exercise—never hold your breath.
Cooling Down—Finish with 5 to 10 minutes of
stretching. Stretching increases the flexibility of your
muscles and helps to prevent post-exercise problems.
EXERCISE FREQUENCY
To find the proper intensity level, find your age at the
bottom of the chart (ages are rounded off to the nearest ten years). The three numbers listed above your
age define your “training zone.” The lowest number is
the heart rate for fat burning, the middle number is the
heart rate for maximum fat burning, and the highest
number is the heart rate for aerobic exercise.
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest
between workouts. After a few months of regular exercise, you may complete up to five workouts each
week, if desired. Remember, the key to success is to
make exercise a regular and enjoyable part of your
everyday life.
22
SUGGESTED STRETCHES
The correct form for several basic stretches is shown at the right. Move slowly as you stretch—never bounce.
1. Toe Touch Stretch
1
Stand with your knees bent slightly and slowly bend forward from
your hips. Allow your back and shoulders to relax as you reach
down toward your toes as far as possible. Hold for 15 counts, then
relax. Repeat 3 times. Stretches: Hamstrings, back of knees and
back.
2. Hamstring Stretch
2
Sit with one leg extended. Bring the sole of the opposite foot
toward you and rest it against the inner thigh of your extended leg.
Reach toward your toes as far as possible. Hold for 15 counts,
then relax. Repeat 3 times for each leg. Stretches: Hamstrings,
lower back and groin.
3. Calf/Achilles Stretch
With one leg in front of the other, reach forward and place your
hands against a wall. Keep your back leg straight and your back
foot flat on the floor. Bend your front leg, lean forward and move
your hips toward the wall. Hold for 15 counts, then relax. Repeat 3
times for each leg. To cause further stretching of the achilles tendons, bend your back leg as well. Stretches: Calves, achilles tendons and ankles.
3
4
4. Quadriceps Stretch
With one hand against a wall for balance, reach back and grasp
one foot with your other hand. Bring your heel as close to your
buttocks as possible. Hold for 15 counts, then relax. Repeat 3
times for each leg. Stretches: Quadriceps and hip muscles.
5. Inner Thigh Stretch
Sit with the soles of your feet together and your knees outward.
Pull your feet toward your groin area as far as possible. Hold for
15 counts, then relax. Repeat 3 times. Stretches: Quadriceps and
hip muscles.
23
5
NOTES
24
PART LIST
Key No. Qty.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
1
1
1
1
1
1
1
2
5
1
2
1
1
1
6
1
1
2
6
1
1
1
1
1
2
2
2
4
2
2
2
2
1
2
2
1
1
1
1
1
1
1
1
Description
Key No. Qty.
Frame
Ramp
Upright
Console
Shield Cover
Upright Cover
Ramp Cover
Wheel
Foot
Eddy Mechanism
Pedal Leg Tube
Idler
Pulley
Crank
Crank Bearing
Resistance Motor
Rear Ramp Cover
Magnet
Pivot Bushing
Clamp
Reed Switch/Wire
Left Handlebar
Left Upper Body Arm
Left Pedal Leg
Link Arm
Pedal
Roller
Weld Spacer
Roller Axle
Link Tube
Crank Arm
Key
Left Side Shield
Upper Body Cap
Rear Handle Cover
Right Handlebar
Right Upper Body Arm
Right Pedal Leg
Right Pedal Bracket
Right Side Shield
Pivot Axle
Crank Arm Spacer
Belt
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
*
*
*
2
2
1
1
1
1
2
2
2
2
2
2
2
6
2
2
4
4
2
2
4
4
19
3
4
8
2
2
1
2
2
4
2
4
2
11
4
6
5
1
–
–
–
Model No. PFEL06611.0 R0911A
Description
Handle Grip
Link Arm Cap
Wire Harness
Power Harness
Left Pedal Bracket
Stabilizer
Stabilizer Cap
M6 x 9mm Screw
M8 x 50mm Hex Screw
Large Snap Ring
Small Snap Ring
M6 x 14mm Flat Head Screw
Barrel Nut
M6 x 18mm Screw
M10 x 120mm Screw
M10 x 20mm Screw
M6 Nylon Locknut
M8 x 55mm Screw
M8 x 50mm Screw
M10 x 22mm x 1.5mm Washer
M10 x 27mm Screw
M8 x 19mm Screw
#8 x 3/4" Screw
M4 x 16mm T Screw
#8 x 2" Screw
M6 x 12mm Screw
M10 x 29mm x 2mm Washer
M10 x 15mm Screw
#8 x 1/2" TZP Screw
M10 Nylon Locknut
M10 x 89mm Hex Screw
Pedal Leg Bushing
M8 Nylon Locknut
M8 Hex Nylon Locknut
M8 Hex Nylon Locknut Cls 10.9
#8 x 1/2" Screw
M4 x 16mm Screw
Hood Clip
Custom Clip
Power Supply
Assembly Tool
Grease Packet
Userʼs Manual
Note: Specifications are subject to change without notice. For information about ordering replacement parts, see
the back cover of this manual. *These parts are not illustrated.
25
66
66
67
35
67
81
81
26
66
79
81
66
35
17
79
79
66
79
79
33
66
82
5
66
79
7
6
79
81
82
66
4
66
81
67
66
81
40
66
EXPLODED DRAWING A
Model No. PFEL06611.0 R0911A
27
57
45
71 63
34
56
22
54
30
29
9
27
55
25
48
44
61
15
68
53
69
9
2
70
26
15
59
64
74
23
19
77
39
26
24
73
52
28
32
19
42
31
13
18
19
69
75
41
51
78
65
3
11
75
15
9
28 20
72
14
18
46
15
10
12
28
61
55
31
9
63
30
38
71
11
62
16
74
52
37
59
70
50
19
60
73
19
27 29
45
54
77
47
1
21
19
65
80
75
25
56
28
32
51
78
79
8
76
75
49
36
43
9
58
15
76
34
50
53
15
8
62
57
83
79
44
EXPLODED DRAWING B
Model No. PFEL06611.0 R0911A
ORDERING REPLACEMENT PARTS
To order replacement parts, please see the front cover of this manual. To help us assist you, be prepared to
provide the following information when contacting us:
• the model number and serial number of the product (see the front cover of this manual)
• the name of the product (see the front cover of this manual)
• the key number and description of the replacement part(s) (see the PART LIST and the EXPLODED
DRAWING near the end of this manual)
LIMITED WARRANTY
IMPORTANT: You must register this product within 30 days of the purchase date to avoid added
fees for service needed under warranty. Go to www.proformservice.com/registration.
ICON Health & Fitness, Inc. (ICON) warrants this product to be free from defects in workmanship and
material, under normal use and service conditions. The frame is warranted for a lifetime. The resistance
mechanism is warranted for seven (7) years. Parts and labor are warranted for ninety (90) days from the
date of purchase.
This warranty extends only to the original purchaser (customer). ICONʼs obligation under this warranty is
limited to repairing or replacing, at ICONʼs option, the product through one of its authorized service centers. All repairs for which warranty claims are made must be preauthorized by ICON. If the product is
shipped to a service center, freight charges to and from the service center will be the customerʼs responsibility. If replacement parts are shipped while the product is under warranty, the customer will be responsible for a minimal handling charge. For in-home service, the customer will be responsible for a minimal
trip charge. This warranty does not extend to freight damage to the product. This warranty will automatically be voided if the product is used as a store display model, if the product is purchased or transported
outside the USA, if all instructions in this manual are not followed, if the product is abused or improperly
or abnormally used, or if the product is used for commercial or rental purposes. No other warranty beyond
that specifically set forth above is authorized by ICON.
ICON is not responsible or liable for indirect, special, or consequential damages arising out of or in connection with the use or performance of the product; damages with respect to any economic loss, loss of
property, loss of revenues or profits, loss of enjoyment or use, or costs of removal or installation; or other
consequential damages of any kind. Some states do not allow the exclusion or limitation of incidental or
consequential damages. Accordingly, the above limitation may not apply to the customer.
The warranty extended hereunder is in lieu of any and all other warranties, and any implied warranties of
merchantability or fitness for a particular purpose are limited in their scope and duration to the terms set
forth herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the
above limitation may not apply to the customer.
This warranty provides specific legal rights; the customer may have other rights that vary from state to state.
ICON Health & Fitness, Inc., 1500 S. 1000 W., Logan, UT 84321-9813
Part No. 323092 R0911A
Printed in USA © 2011 ICON IP, Inc.