Cooper Power Tools (QuackenBush) Advanced

RightAnglePositive
FeedTools
ADVANCED DRILLING EQUIPMENT
2-1
SP-1300-2-EN-0806-.25M
Introduction
Right Angle Positive Feed Tools
Our positive feed drill motors are available in both
in-line and right angle configurations (please also
see the in-line tool section), The right angle tools are
rapidly growing in popularity due to their compact
size, light weight and ease of operation.
In-line drills have a limited stroke, but with a right
angle drill a deeper stroke can be achieved by
simply applying a longer spindle and nosepiece. In
addition, the fixtures do not have to be as robust
with a right angle drill, which represents a significant
cost savings. The tools themselves weigh less and
in use are closer to the fixture, resulting in less
deflection of the fixture. Right angle tools have also
been shown to reduce operator fatigue.
In general, positive feed drills are used for the
larger holes and heavier structures in the aircraft
industry such as the spars and the ribs, primarily in
landing gear, wing and fuselage joins.
Positive feed drills produce a hole in a predictable
and constant time. With each revolution of the spindle,
the cutter travels a precise distance, i.e., onethousandth of an inch or three-thousandths of an
inch depending on the settings. This is true whether
the tool is drilling air or drilling a tough alloy. The
benefit is that burrs caused by surging
of the cutter on the exit side of the
cycle are virtually eliminated.
Spindle
Since the cutter advances a precise
Guard
distance with each revolution, the cutter
Differential Feed Gear and
does not rotate without cutting. This
Differential Drive Gear
reduces heat and deformation, resulting
Feed Stop
Air Motor
in less chance of the material work
Collar
Feed
hardening.
Engagement
Many of the accessories for our
Spindle
Lever
in-line and right angle tools are
interchangeable, such as chucks, nose
pieces, motors and gears.
How Positive Feed Right
Angle Drills Operate
Spindle
Feed Gear
(Threaded)
Spindle
Drive Gear
(Splined)
Tool Nose
2-2
The fixed rate of spindle advancement
(feed) for each rotation of the drill spindle
in right angle tools is accomplished by
differential gearing. The spindle of a right
angle drill has external left-hand threads
and four drive grooves that run the
length of the spindle. The spindle fits
into and through two gears: the spindle
drive gear and the spindle feed gear.
The spindle drive gear has internal
male splines that engage the drive
grooves on the spindle. When the air
motor is turned on, the spindle drive
gear rotates, turning the spindle.
The spindle feed gear is threaded
internally to match the external thread
of the spindle, and its function is to
advance or retract the spindle. When this gear
rotates faster than the spindle, the spindle will feed.
When it stops, the spindle will retract. The desired
feed rate is obtained by the differential gear ratio
between the spindle drive and spindle feed gears.
At the completion of the drilling cycle, the feed
stop collar contacts the feed engagement lever,
lifting the differential feed gear and locking it in a
stationary position. With the spindle continuing to
rotate in a forward direction and the spindle feed
gear held stationary, the spindle automatically
retracts. This action occurs approximately three
times faster than the advancement cycle.
Depending on the positive feed model selected, the
tool is shut down either manually or automatically.
Taper-Lok Fixturing
Customized fixtures are constructed to accept
Taper-Lok Bushing Tips. Advanced Drilling
Equipment tools with the Bushing Tips are inserted
into the fixture, twisted and cam-locked into place.
Tool Nose
Tooling Fixture
Lock
Screws
Standard Threaded
Drill Bushing
The Bushing Tip‘s tapered flanges fit under the
shoulder of lock screws in the fixture. The Bushing
Tip holds the tool in alignment and absorbs the
thrust and torque of drilling. At the completion of the
drilling cycle, the tool is rotated to unlock, withdrawn
from the fixture and moved to the next position.
Several different types of Taper-Lok Fixturing are
available. The following are the most common.
Lock Liners
Direct Mounting
Direct Mounting
Lock Strip
Method for mounting to
a fixture. A hole is bored
in the jig to accomodate
the lock liner bushing.
The lock ring holds the
lock liner bushing in
position in the jig.
The Serrated Liner is
used in potted or
cast-in-place
installations.
Most common mounting
method has lock screws
mounted directly into the
fixture plate. The shank
of the drill bushing tip fits
directly into a bored hole
in the fixture plate.
This method for closely
spaced holes employs a
lock strip along each side
of the row of holes in the
fixture plate. The flanges
on the Drill Bushing Tip
lock under the extended
edges of the lock strip.
Taper-Lok
Bushing
B – Radius
(For Taper-Lok
Clamp or Lock
Screw)
1/4–20
Hex
Head
Screw
A
Taper-Lok
Clamp or
Lock Screw
design
Lock
Strip
Design
Location Data for Taper-Lok Clamp,
Lock Screw, and Lock Strip Mounting
Drill Bushing
Tip Series
A
B
Tool Nose
Thread (I.D.)
21000
22000
23000
24000
25000
.312
.609
.734
.859
None
.625
.922
1.047
1.172
1.562
3/4–16
1–14
1 1/4–12
1 1/2–12
2–16
2-3
Right Angle Tools
932QR
942QR
Capacity:
Aluminum - .5625”(14.3mm)
Titanium - .4375” (11.1mm)
Steel - .4375” (11.1mm)
Stroke:
Unlimited
Min. - .375” (9.5mm)
䡵 0.9 and 1.3 nominal
horsepower motors.
䡵 Right angle tool designed
for close quarter operation.
䡵 Utilizes spindles of varying lengths to provide unlimited hole depth capability.
䡵 Utilizes spindles which accommodate threaded and straight shank cutters.
Fluid spindle for threaded cutter only.
䡵 Stroke is adjustable by positioning two stop collars.
䡵 Spindle continues to rotate in forward directon on return stroke to eliminate
withdrawal spiral in hole.
䡵 Rapid spindle retraction.
䡵 Spindle can be retracted at any point during feed cycle by depressing the
manual return lever.
䡵 Feed is engaged by pressing the feed button.
䡵 Tool automatically shuts off at completion of drill cycle.
䡵 932QR drill, 942QR drill and countersink.
䡵 Easily adaptable to Quackenbush 1/2”-22 OD thread spindle.
Options
䡵 Vacuum on nose and concentric collet
䡵 Concentric collet
䡵 Pneumatic counter
䡵 Electronic back-counter
䡵 Micro-pump
䡵 Handle on the upper side
Motor
Model Configuration
HP
Max. Stroke
in.
mm
Weight
lbs
kg
Max. Length
in.
mm
Spindle
Speeds
932QR
Right Angle
0.9
No Limit
5.8
2.2
13.92 354
450, 800, 4500
932QR
Right Angle
1.3
No Limit
5.8
2.2
13.92 354
Right Angle
0.9
No Limit
5.8
2.2
13.92 354
1300, 1600,
2000, 3200
450, 800, 4500
942QR
942QR
Right Angle
1.3
No Limit
5.8
2.2
13.92 354
.0005, .001, .002,
.003, .004, .006
.0005, .001, .002,
.003, .004, .006
.0005, .001, .002,
.003, .004, .006
.0005, .001, .002,
.003, .004, .006
.013, .03, .05,
.07, .10, .15
.013, .03, .05,
.07, .10, .15
.013, .03, .05,
.07, .10, .15
.013, .03, .05,
.07, .10, .15
Rated tool performance at 90 PSIG measured at tool inlet with motor running.
WHEN ORDERING TOOL:
EXTRA EQUIPMENT:
Tool nose and spindle must be specified when tool is ordered.
Nose, spindle, spindle guard.
2-4
1300, 1600,
2000, 3200
Feed Per Revolution
Inches
mm
Inlet
Min.
Hose
.250” NPT
.375”
.250” NPT
.375”
.250” NPT
.375”
.250” NPT
.375”
Right Angle Tools
932
Q R – XXXX – .XXXX – MS – B B – A – A – XXX
Tool Series
932 Right Angle
942 Right Angle (Countersink)
Last three digits
of material number
Accessories
A = Nose
B = Chuck
C = Other (specify)
Quackenbush
Options
A = Micro pump
F = Handle w/trigger
w/counter
G = Handle wo/trigger
B = Micro pump
I = Indexer
wo/counter
J = Large ID indexer
C = Counter
(special 932QR only)
D = Concentric collet X = None
E = HP booster (1300, 1600, 2000, 3200
RPM models only)
Tool Style
R = Right Angle
Spindle Speed (RPM)
Select desired speed from catalog
.9 Nominal HP
1.3 Nominal HP
450 RPM
800 RPM
4500 RPM
1300
1600
2000
3200
RPM
RPM
RPM
RPM
Spindle Stroke
A = 40mm (1.57”)
B = 60mm (2.36”)
C = 80mm (3.15”)
D = 100mm (3.94”)
Feed Rate
05 = .0005 IPR 30 = .003 IPR
10 = .001 IPR 40 = .004 IPR
20 = .002 IPR 60 = .006 IPR
E = 120mm (4.72”)
F = 140mm (5.51”)
G = 180mm (7.08”)
H = 1/2-22 (specify length)
(932QR only)
Motor Stop
MS = Motor Stop 932QR
DS = Depth Sensing 942QR
Spindle Thread
A = 1/4 - 28
B = 5/16 - 25
C = 3/8 - 24
D = M8 x 100 internal
E = M6 x 100 internal
F = 9/16 - 18
Quackenbush 932QR & 942QR Tool Noses & Spindle Assemblies
■ When ordering a tool, specify one nose and spindle assembly from chart below. (Spindle assembly includes
spindle and spindle guard.)
■ Order Tool Nose Adapter (614722) to attach S125 & S300 Tool Noses.
■ Order Tool Nose Adapter (614973) to attach S150 & S275 Tool Noses.
■ Other Noses and Spindles are available upon request.
■ Optional mounted lubricator with counter (22007057) and without counter (22007067) are available.
■ Use spindle adapter 632759 to adapt 3/8” capacity three jaw chuck 849108 to spindles with 3/8”-24 internal threads.
Standard Tool Noses
Bushing Thread
Length X
Part Number
.75 - 16 UN LH
.75 - 16 UN LH
1” -14 UN LH
1” -14 UN LH
3.0”
4.0”
3.0”
4.75”
614905
614824
624812
614814
Fluid Spindle Assemblies
Bayonet Nosepiece
Specify Shank Diameter and Cutter Guide Diameter in
Nosepiece Term. Code. Specify overall length as Bayonet
Nosepiece Length.
J
K
L
M
N
Body Length
Shank Diameter
Cutter Guide Diameter
Bayonet Lock Wing
Bushing Length
Stroke
Cutter End
Part Number
2.25”
2.25”
2.25”
3.00”
.250” - 28
.3125” - 24
.375” - 24
.375” - 24
22005572
22005582
22005592
22005594
Adapter Kits
Description
Convert Inline tool to Right Angle
Convert Right Angle tool to Inline
Part Number
92050932
92050952
2-5
Right Angle Tools
15QDA-RAB-SU-RS Series
Capacity:
Aluminum – .5625” (14.3mm)
Titanium – .4375” (11.1mm)
Steel – .4375” (11.1mm)
Stroke:
Unlimited
Min. – .375” (9.5mm)
䡵 15 series motor develops 1.0 nominal horsepower.
䡵 Right angle tool designed for close quarter operation.
䡵 Utilizes spindles of varying lengths to provide
unlimited hole depth capability.
䡵 Tool utilizes spindles which accomodate threaded
shank, straight shank and morse taper.
䡵 Easily adapted to oil hole drilling using a solid
spindle and a fluid chuck, or with the use of an oil
hole spindle and a fluid swivel.
䡵 Stroke is adjustable by positioning the stop collar.
䡵 Spindle continues to rotate in forward directon on
return stroke to eliminate withdrawal spiral in hole.
䡵 Rapid spindle retraction.
䡵 Spindle can be retracted at any point during feed
cycle by lifting retract lever.
䡵 Automatic retract stop with protective rolling impulse
clutch prevents accidental jamming of spindle at end of retract.
䡵 Feed is engaged by pressing down on feed engagement lever.
䡵 Tool is manually shut off at completion of drill cycle.
15QDA-RAB-SU-RS
Model
15QD-RAB-SU-RS
2-6
Motor
Configuration
Maximum Stroke
Right Angle
No Limit
in.
mm
Weight
Maximum Length
lbs
kg
in.
mm
5
2.27
13 3/8
34
Spindle
Speeds
165, 265,
335, 465, 660,
1000, 1650
Feed Per
Revolution
.0005, .001,
.002, .003,
.006
Inlet
Minimum
Hose Size
.375” NPT
.375”
EXTRA EQUIPMENT:
WHEN ORDERING TOOL:
Tool Noses, Spindles.
Rated tool performance at 90 PSIG measured at tool inlet with motor running.
When selecting speeds and feeds, see page I-5.
Mist lubricator – 631889
SEE PAGES I-11–I-13 FOR SAFETY PRECAUTIONS.
SEE PAGE 2-22 – 2-25 FOR TOOLING ACCESSORIES.
Tool nose and spindle must be specified. Other tool noses and spindles are
available at extra charge – see page 2-26.
Right Angle Tools
STEEL TOOL NOSES (Select One)
Dia. “A”
Length
1.1875” (30mm) 3” (76mm)
1.25” (32mm)
3” (76mm)
“C” Thread
Part No.
.75”-16 L.H. (21000)
1.0”-14 L.H. (22000)
614905
614906
SPINDLES (Select One)
Spindle Length
Type
"B"
Max.
Stroke
Thread Description
Part No.
Solid
4”
1.12”
(101mm) (29mm)
.25”-28 Internal Thread
623266
Solid
4”
1.12”
(101mm) (29mm)
.375”-24 Internal Thread
with Counterbore
615915
1/2–22 L.H.
䡵 Order Tool Nose Adapter (614722) to attach S125 & S300 Tool
Noses (1.75” O.D.) and accessories. (See page 2-26)
䡵 Order Tool Nose Adapter (614973) to attach S150 & S275 Tool
Noses (2” 0. D.) and accessories (See page 2-26)
䡵 Order Chuck Adapter (619136) when utilizing 3-jaw chuck with .375
-24 Internal Thread Spindles.
䡵 Fluid Swivel (631256) used with Oil Hole Spindles, and selection of
Fluid Chucks. (See page 2-28)
䡵 Fluid Chucks used with .375 -24 Internal Thread Spindles.
䡵 Other Noses and Spindles are available as required (see page 2-24).
䡵 Nose Indexer (631249). New design 641244.
2-7
Right Angle Tools
15QDA-RAB-SU-RS-RF Series Back Spotfacer
Stroke:
Min. - .375” (9.5mm)
Max. - Unlimited
䡵 15 series motor develops
1.0 nominal horsepower.
䡵 Right angle tool designed for
close quarter operation.
䡵 Stroke is adjustable by positioning the stop collar.
䡵 Spindle continues to rotate in
forward directon on return stroke.
䡵 Rapid spindle retraction.
䡵 Spindle can be retracted at any point during feed cycle
by lifting retract lever.
䡵 Automatic retract stop with protective rolling impulse
clutch prevents accidental jamming of spindle at end of retract.
䡵 Feed is engaged by pressing down on feed engagement lever.
䡵 Tool is manually shut off at completion of drill cycle.
䡵 Spindle guard protects operator.
15QDA-RAB-SU-RS-RF
Model
Motor
Configuration
15QDA-RAB-SU-RS-RF Right Angle
Maximum Stroke
in.
mm
No Limit
Weight
kg
in.
mm
5
2.27
13 3/8
34
EXTRA EQUIPMENT:
Noses and spindles must be specified when ordering.
Rated tool performance at 90 PSIG measured at tool inlet with motor running.
2-8
Maximum Length
lbs
Spindle
Speeds
Feed Per
Revolution
160, 265, 335, .0005, .001,
465, 660
.002, .003,
1000, 1650
.006
When selecting speeds and feeds, see page I-5.
SEE PAGES I-11–I-13 FOR SAFETY PRECAUTIONS.
SEE PAGE 2-22 – 2-25 FOR TOOLING ACCESSORIES.
Inlet
Minimum
Hose Size
.375” NPT
.375”
Right Angle Tools
STANDARD EQUIPMENT
Specify nose and spindle when ordering.
ALUMINUM TOOL NOSE
Length
Thread
Part No.
6.875 in. (175mm)
7.125 in. (181mm)
7.125 in. (181mm)
.75 - 16LH
1 - 14LH
1.25 - 12LH
619954
619955
619953
THREAD: .5-22 R.H. Thread
INTERNAL THREAD: .375 - 24 with Counterbore
MAX. STROKE; 3.626” (92MM)
PART NO: 624146-7
2-9
Right Angle Tools
140QGDA-RA-SU-MS Series
Capacity:
Aluminum – .5625” (14.3mm)
Titanium – .4375” (11.1mm)
Steel – .4375” (11.1mm)
Stroke:
Min. – .3125” (8mm)
Max. – Unlimited
䡵 140 series motor develops 1.4 nominal horsepower.
䡵 Single push-button starts motor and engages drill feed mechanism.
䡵 Stroke is adjustable by positioning the stop collar.
䡵 Externally replaceable shear pin provides gear protection if chips
pack or cutter binds.
䡵 Rapid advance with manual speed control and low torque clutch
protection if cutter advances into workpiece.
䡵 Precision depth control with automatic retract after preset
dwell period.
䡵 Positive depth stop is adjustable for desired hole depth.
䡵 Easily adapted to oil hole drilling using a solid spindle and a fluid
chuck, or with the use of an oil hole spindle and a fluid swivel.
䡵 Cutter automatically retracts if tool senses thrust overload.
䡵 Motor shuts off automatically after retract.
䡵 Auxilliary manual retract lever.
䡵 Emergency push-button stops motor and disengages drill
feed mechanism.
140QGDA-RA-SU-MS
Motor
Configuration
Maximum Stroke
140QGDA-RA-SU-MS
Right Angle
140QDA-RA-SU-MS
Right Angle
Model
2-10
in.
mm
Weight
Maximum Length
lbs
kg
in.
mm
No Limit
10.75
4.88
19.875
505
No Limit
10.75
4.88
19.875
505
Spindle
Speeds
Feed Per
Revolution
Inlet
Minimum
Hose Size
95, 150, 200, .0005, .001,
260, 380, 580, .002, .003,
1000
.006
.375” NPT
.5”
1,400
.375” NPT
.5”
.0005, .001,
.002, .003,
.006
EXTRA EQUIPMENT:
WHEN ORDERING TOOL:
Noses and spindles must be specified when ordering.
Rated tool performance at 90 PSIG measured at tool inlet with motor running.
When selecting speeds and feeds, see page I-5.
SEE PAGES I-11–I-13 FOR SAFETY PRECAUTIONS.
SEE PAGE 2-22 – 2-25 FOR TOOLING ACCESSORIES.
Tool nose and spindle must be specified. Standard tool noses, spindle guard and
spindle are provided when ordered with tool. Select one tool nose and one spindle.
Other tool noses and spindles are available at extra charge – see page 2-26.
Right Angle Tools
2.6”
(66 MM)
.65”
(17 MM)
1.69”
(43 MM) 1.41”
(36 MM)
18.6” (474 MM) FOR 1400 RPM, 1000 RPM, 580 RPM & 380 RPM
19.8” (505 MM) FOR 200 RPM, 160 RPM, 120 RPM & 75 RPM
5.38” (137 MM)
Ø 2.59” (66 MM)
3.38”
(86 MM)
2.56”
(66 MM)
3/8-18
NPT
1-20 UNEF-2A THD
Nosepiece Mounting Thread
STANDARD TOOL NOSES
STEEL TOOL NOSES (Select One)
Dia. “A”
Length
1.1875” (30mm) 5” (127mm)
“C” Thread
Part No.
.75”-16 L.H. (21000)
614919
SPINDLES (Select One)
Spindle Length
Type
"B"
Thread Description
Spindle
Part No.
Spindle
Guard No.
6”
2.75”
(152mm) (70mm)
.375”-24 Internal Thread
with Counterbore
615747
624342
Oil Hole 6”
2.75”
(152mm) (70mm)
.375”-24 Internal Thread
with Counterbore
623812
624332
Solid
1/2–22 L.H.
䡵 Order Tool Nose Adapter (629222) to attach S125 & S300 Tool
Noses (1.75” O.D.) and accessories. (See page 2-24)
䡵 Order Tool Nose Adapter (629224) to attach S150 & S275 Tool
Noses (2” 0. D.) andaccessories (See page 2-24)
䡵 Order Chuck Adapter (619136) when utilizing 3-jaw chuck with .375
-24 Internal Thread Spindles.
Max.
Stroke
䡵 Fluid Swivel (631256) used with Oil Hole Spindles, and selection of
Fluid Chucks. (See page 2-25)
䡵 Fluid Chucks used with .375 -24 Internal Thread Spindles.
䡵 Other Noses and Spindles are available as required (see pg. 2-26).
䡵 Nose Indexer (631864). New design 641267.
2-11
Right Angle Tools
904QR
Capacity (Diameter):
Aluminum – .80” (20mm)
Titanium – .63” (16mm)
䡵 Very lightweight and compact
Powerful 1.6 HP Motor yet compact
Only .80 from centerline to side of Angle Head
For straight hole applications
䡵 Easy to setup and operate
Automatic Retract
Standard Quackenbush motor
䡵 Variety of speeds, and feed rates
All control valves in one module
Thru-spindle cutter lubrication
䡵 Bayonet or Taperlock Fixturing
Concentric Collet - see page 6-8
Handle for convenient handling
䡵 Options:
Nosepiece Indexer - easy to operate to orient clamp up
Precision Depth Control - contact Factory
Telescoping Spindle for limited access areas
Concentric collet
Spindle
Speed
Model
904QR
175, 350
525, 700
1100, 1500
1750
Feed Rate (rev)
Stroke
in.
mm
in.
mm
.001
.002
.003
.004
.006
0.025
0.050
0.075
0.100
0.150
2.4
3.1
4.0
4.8
60
80
100
120
Spindle
Termination
Spindle Termination
3/8” Geared Chuck
5/16” - 24 Int’l Thread, 120 Taper
3/8” - 24 Int’l Thread, 120 Taper
7/16” - 20 Int’l Thread, 120 Taper
Note: All threaded spindles provide for thru-the-spindle cutter lubrication.
Nosepiece Termination
Bayonet Nosepieces - pages 6-6
None, M28 x 150 LH Internal Nosepiece Thread
Bayonet Nosepiece Code.
Specify Shank Diameter & Cutter Guide Diameter.
Example: 20 mm Shank Diameter
12.57 Cutter Guide Diameter
Note: Use threaded spindle terminations for Nosepieces P.
Taperlock Nosepieces - pages 2-20
22000 Taperlock (1.000-14 LH)
23000 Taperlock (1.250-12 LH)
24000 Taperlock (1.500-12 LH)
None, 1.000-20 LH Ext’l Mounting Thread
None, 1.562-20-14 LH Int’l Mounting Thread
None, 1.825-18 LH Ext’l Mounting Thread
2-12
Nosepiece
Termination
Nosepiece
Length
Accessories
Accessories
Drill Point Lubricator Q, Pressure Fill
Drill Point Lubricator - Fluid Pump
Nose Indexer, 1”-1/4-16 LH
Fluid Inducer
Vacuum Collector Port
Air Inlet Adapter - 3/8” NPT
Nosepiece Length
Bayonet Nosepiece Length
mm
in.
mm
in.
44
59
64
69
74
1.73
2.32
2.52
2.72
2.92
79
84
89
94
3.11
3.31
3.50
3.70
Taperlock Nosepiece Length
See page 2-22: Select noespiece length
appropriate to Taperlock Series.
Right Angle Tools
D
C
A
B
C
D
E
F
G
H
E
B
H
Air Inlet
3/8” BSP int.
A
F
G
Air Inlet
On/Off Slide Valve
Spindle Guard
Dead Handle
Drill Point Lubricator
Nosepiece Indexer Lever (Optional)
Nosepiece Mounting Thread
Feed Button
M28x1.5LH
without nosepiece
indexer
1 1/4”-16LH with nosepiece indexer
1.57
(40)
14.61
(371.1)
Bayonet Nosepiece
Specify Shank Diameter and Cutter Guide Diameter in
Nosepiece Term. Code. Specify overall length as Bayonet
Nosepiece Length. For complete Bayonet details, see page
6-6.
J
K
L
M
N
Body Length
Shank Diameter
Cutter Guide Diameter
Bayonet Lock Wing
Bushing Length
Concentric Collet
See page 6-8 for 20904 with Concentric Collet and Depth
Sensing.
Taperlock Nosepieces
Quackenbush Nosepieces are provided to utilize Taperlock
Bushing Tips. Taperlock Series must be specified-for
details, see pages 1-3 and 2-20.
Setup
Operation
1. Install cutter; verify cutter guide bushings are correct size.
2. Adjust stroke by removing spindle guard, rotating End Stop
and tighten Lock Screws.
3. Adjust Drill Point Lubricator to give desired flow rate.
4. (Option) Depress Indexer Lever and rotate Nosepiece
to give optimum orientation.
1. Set Nosepiece into fixture and rotate to lock.
2. Push Slide Valve forward; motor starts, spindle
rotates but does not advance.
3. Push Feed Button - spindle/cutter moves at fixed feed rate.
4. At end of stroke, spindle/cutter automatically returns
to start position and motor stops.
5. Pull Slide Valve rearward - motor stops.
SPECIFICATIONS:
GENERAL INFORMATION SEE PAGES NOTED:
Air Inlet = 3/8” BSP
Power = 1.2 KW (1.6 HP)
Depth Repeatability = 0.025 mm (.001 inch) with
Depth Sensing Nosepiece
Weight = 5.9 Kg (13.2 lb) with typical spindle
and nosepiece
Spindle Offset = 20 mm (0.80 Inch)
Air Consumption = 1550 L/Min (55 CFM)
Noise = 80 dBA
To determine:
Speed, page I-14
Bayonet Fixturing: page 6-6
Taperlock Fixturing: page 1-3
At all times Verify that Guards are in place and
secure. Operators must understand and follow
Safety Practices - See Pages I-11.
2-13
Right Angle Tools
158QGD-15RAB-SU-RS Series
Capacity:
Aluminum - .5625”
(14.28mm)
Stroke:
Unlimited
Min. - .375”
䡵 158 series motor develops
1.6 nominal horsepower.
䡵 Right angle tool designed
for close quarter operation.
䡵 Utilizes spindles of varying lengths to provide
unlimited hole depth capability.
䡵 Tool utilizes spindles which accomodate threaded
shank, straight shank and Morse Taper.
䡵 Easily adapted to oil hole drilling using a solid spindle
and a fluid chuck, or with the use of an oil hole
spindle and a fluid swivel.
䡵 Stroke is adjustable by positioning the stop collar.
䡵 Spindle continues to rotate in forward directon on
return stroke to eliminate withdrawal spiral in hole.
䡵 Rapid spindle retraction.
䡵 Spindle can be retracted at any point during feed
cycle by lifting retract lever.
䡵 Automatic retract stop with protective rolling impulse
clutch prevents accidental jamming of spindle at end
of retract.
䡵 Feed is engaged by pressing down on feed
engagement lever.
䡵 Tool is manually shut off at completion of drill cycle.
158QGD-15RAB-SU-RS
Model
Motor
Configuration
158QGD-15RAB-SU-RS Right Angle
2-14
Maximum Stroke
in.
mm
No Limit
Weight
Maximum Length
lbs
kg
in.
mm
9.25
4.2
16 3/16
411
Spindle
Speeds
550, 1000,
2000, 3000
Feed Per
Revolution
.0005, .001,
.002, .003
Inlet
Minimum
Hose Size
.375” NPT
.5”
EXTRA EQUIPMENT:
WHEN ORDERING TOOL:
Tool Noses. Spindles.
Rated tool performance at 90 PSIG measured at tool inlet with motor running.
When selecting speeds and feeds, see page I-5.
SEE PAGES I-11–I-13 FOR SAFETY PRECAUTIONS.
SEE PAGE 2-20 – 2-23 FOR TOOLING ACCESSORIES.
Select one tool nose and one spindle. Other tool noses and spindles are
available at extra charge — see page 2-24.
Right Angle Tools
STANDARD STEEL TOOL NOSE (Part No. 615460)
STEEL TOOL NOSES (Select One)
Dia. “A”
Length
“C” Thread
1.1875” (30mm) 4.5” (114mm) .75”-16 L.H. (21000)
STANDARD SPINDLES
Solid
䡵 Order Tool Nose Adapter (614722) to attach S125 & S300 Tool
Noses (1.75” O.D.) and accessories. (See page 2-26)
䡵 Order Tool Nose Adapter (614973) to attach S150 & S275 Tool
Noses (2” 0. D.) andaccessories (See page 2-26)
䡵 Order Chuck Adapter (619136) when utilizing 3-jaw chuck with
.375 -24 Internal Thread Spindles.
615460
SPINDLES (Select One)
Spindle Length
Type
"B"
1/2–22 L.H.
Part No.
Max.
Stroke
Thread Description
Part No.
6”
3.12”
.375”-24 Internal Thread
(152mm) (79.4mm) with Counterbore
615747
Oil Hole 6”
3.12”
.375”-24 Internal Thread
(152mm) (79.4mm) with Counterbore
623812
䡵 Fluid Swivel (631256) when used with Oil Hole Spindles, and
selection of Fluid Chucks used with .375 -24 Internal Thread
Spindles. (See page 2-25)
䡵 Other Noses and Spindles are available as required (see page 2-26).
䡵 Nose Indexer (631249). New design 641244.
2-15
Right Angle Tools
158QGDA-RAD-SU-RS Series
Capacity:
Aluminum - 1.25” (32mm)
Titanium - 1” (25.4mm)
Steel - 1” (25.4mm)
Stroke:
Min. - .5” (12.7mm)
Max. - Unlimited
䡵 158 series motor develops 1.6 nominal
horsepower.
䡵 Spindle rotates in forward direction during
return stroke.
䡵 Rapid spindle retraction.
䡵 Use of spindles of varying lengths enables
tool to drill holes in confined quarters.
䡵 Easily adapted to oil hole drilling using a solid
spindle and a fluid chuck, or with the use of an
oil hole spindle and a fluid swivel.
䡵 Tool utilizes spindles which accommodate
threaded shank, Morse Taper, straight
shank, reamers and fluid chucks.
䡵 Spindle begins to rotate when motor is turned on.
Tool begins to feed when feed control button is
depressed.
䡵 Spindle may be retracted at any point
during drilling cycle.
䡵 At end of stroke, stop collar on spindle
trips retract lever, causing the spindle to return.
䡵 Tool must be manually shut off.
158QGDA-RAD-SU-RS
䡵 Automatic retract stop with protective rolling
impulse clutch prevents accidental jamming of
spindle at end of retract.
䡵 Spindle guard protects operator.
Motor
Configuration
Maximum Stroke
Right Angle
158QGDAV-RAD-SU-RS Right Angle
Model
158QGDA-RAD-SU-RS
2-16
in.
mm
Weight
Spindle
Speeds
lbs
kg
No Limit
12.5
5.67
47, 56, 70, 94, 110, 120,
140, 185, 194, 230, 288,
380, 388, 460, 485, 570
760, 950
No Limit
12.5
5.67
47/120, 92/230
194/485, 380/950
Feed Per
Revolution
Inlet
Minimum
Hose Size
.0005, .001,
.002, .0035,
.0055, .0075
.375” NPT
.5”
.0005, .001,
.002, .0035,
.0055, .0075
.375” NPT
.5”
EXTRA EQUIPMENT:
WHEN ORDERING TOOL:
Noses and spindles must be specified when ordering.
Rated tool performance at 90 PSIG measured at tool inlet with motor running.
When selecting speeds and feeds, see page I-5.
Mist lubricator (631298-7) may be ordered.
SEE PAGES I-11–I-13 FOR SAFETY PRECAUTIONS.
SEE PAGE 2-22 – 2-25 FOR TOOLING ACCESSORIES.
Tool nose and spindle must be specified. Standard tool noses, spindle guards
and spindles are provided when ordered with tool. Select one
tool nose and one spindle. Other tool noses and spindles are available at extra
charge – see page 2-26.
Right Angle Tools
STEEL TOOL NOSES (Select One)
Length “A”
Thread
Part No.
S400 SERIES
STANDARD STEEL TOOL NOSE
9.5” (241mm) .75”
9.5” (241mm)
1”
9.5” (241mm) 1.25”
9.5” (241mm) 1.5”
9.375” (238mm) 2”
-
16
14
12
12
16
L.H.
L.H.
L.H.
L.H.
L.H.
621235
621236
621237
621238
614751
11.5” (282mm)
1” - 14 L.H.
11.5” (282mm) 1.25”- 12 L.H.
11.5” (282mm) 1.5”- 12 L.H.
11.375” (279m ) 2” - 16 L.H.
621244
621245
621246
614757
S600 SERIES
STANDARD SPINDLES
SPINDLES (Select One)
Spindle
Type
7/8–18 L.H.
䡵 When adapting a 3-jaw chuck to .5625-18 internal thread spindle,
order Chuck Adapter (623643) for .375” cap, chuck OR Chuck
Adapter (619400) for .5” cap. chuck.
䡵 Fluid Swivels used with oil hole spindles and selection of Fluid
Chucks (see page 2-25).
Length
"B"
Max.
Stroke
Thread Description
Part No.
Oil Hole
9.25”
5.5”
.5625”-18 Internal Thread with
(235mm) (140mm) Counterbore and 118° Angle
623955
Oil Hole
9.25”
5.5”
.625”-18 Internal Thread with
(235mm) (140mm) Counterbore and 118° Angle
615964
Solid
9”
5.25” No. 2 Short Morse Taper with
(229mm) (133mm) Side Knock-Out
614470
Solid
9”
5.25” .5625”-18 Internal Thread with
(229mm) (133mm) Counterbore
615319
䡵 Other Noses and Spindles are available on request (see page 2-26).
䡵 Nose Indexers
1.5625 -20 (381326)
2.25 -20 (381327) Use with 615705 nose adapter.
New Design for 2.25-20: 641260
2-17
Right Angle Tools
230QGDA-RAC-SU-MS Series
Capacity:
Aluminum – 1.375” (34.9mm)
Titanium – 1” (25.4mm)
Steel – 1” (25.4mm)
Stroke:
Min. – .125” (3.18mm)
Max. – Unlimited
䡵 230 series motor develops 2.3 nominal horsepower.
䡵 Single push-button starts motor and engages drill
feed mechanism.
䡵 Externally replaceable shear pin provides gear
protection if chips pack or cutter binds.
䡵 Rapid advance with manual speed control and low torque
clutch protection if cutter advances into workpiece.
䡵 Precision depth control with automatic retract after
preset dwell period. (When equipped with depth
sensing nose assembly)
䡵 Positive depth stop is adjustable for desired hole depth.
䡵 Easily adapted to oil hole drilling using a solid spindle and
a fluid chuck, or with the use of an oil hole spindle and a
fluid swivel.
䡵 Cutter automatically retracts if tool senses thrust overload.
䡵 Motor shuts off automatically after retract.
䡵 Auxiliary manual retract lever.
230QGDAV-RAC-SU-MS
Model
Maximum Stroke
Motor
Configuration
in.
mm
Weight*
kg
in.
mm
Spindle
Speeds
Feed Per
Revolution
Inlet
Minimum
Hose Size
230QGDA-RAC-SU-MS
Right Angle
No Limit
17
7.7
20.75
527
50, 65, 80,
100, 125,
160, 205
.0005, .001, .002, .5” NPT
.003, .0045,
.006, .008, .012
.5”
230QGDA-RAC-SU-MS
Right Angle
No Limit
15.75
7.1
18.75
476
260, 320, 390, .0005, .001, .002, .5” NPT
440, 550, 640, .003, .0045,
770, 1000
.006, .008, .012
.5”
230QGDAV-RAC-SU-MS Right Angle
No Limit
17.5
7.9
21.25
549
50/125
100/250
.0005, .001, .002, .5” NPT
.003, .0045,
.006, .008, .012
.5”
230QGDAV-RAC-SU-MS Right Angle
No Limit
16.25
7.4
19.25
489
210/520
420/1000
.0005, .001, .002, .5” NPT
.003, .0045,
.006, .008, .012
.5”
*Weight and Length will vary depending on Gear Train.
NOTE:
Tool model with either the 2.25”-20 L.H. External Nose Attachment Thread
(Standard) or the 1.5625”-20 Internal Thread (Special) must be specified
when ordering.
Rated tool performance at 90 PSIG measured at tool inlet with motor running.
When selecting speeds and feeds, see page I-5.
2-18
Length*
lbs
SEE PAGES I-11–I-13 FOR SAFETY PRECAUTIONS.
SEE PAGE 2-22 – 2-25 FOR TOOLING ACCESSORIES.
WHEN ORDERING TOOL:
Tool nose and spindle must be specified. Standard tool nose, spindle guard and
spindle are provided when ordered with tool. Select one tool nose and one
spindle. Specify EITHER 2.25”-20 External Thread OR
1.5625”-20 LH Internal Thread.
Right Angle Tools
STEEL TOOL NOSES (Select One)
Length “A”
STANDARD TOOL NOSE
Thread
Part No.
S400 SERIES
9.5” (241mm) .75”
9.5” (241mm)
1”
9.5” (241mm) 1.25”
9.5” (241mm) 1.5”
9.375” (238mm) 2”
-
16
14
12
12
16
L.H.
L.H.
L.H.
L.H.
L.H.
621235
621236
621237
621238
614751
11.5” (282mm)
1” - 14 L.H.
11.5” (282mm) 1.25”- 12 L.H.
11.5” (282mm) 1.5”- 12 L.H.
11.375” (279m ) 2” - 16 L.H.
621244
621245
621246
614757
S600 SERIES
STANDARD SPINDLE
SPINDLES (Select One)
Spindle
Type
12.5 L.H.
䡵 2.25”-20 Nose Thread Attachment on standard tool accepts S400
and S600 Tool Noses and accessories.
䡵 For close quarter applications, a special tool with
1.5625”-20 L.H. Internal Nose Attachment Thread is available.
䡵 With the 1.5625”-20 L.H. Internal Thread, order Nose Adapter
(614244) to attach S150 and S275 (2” O.D.) Tool Noses and
accessories, OR Nose Adapter (614228) to attach S400 and S600
(2.375” O.D.) Tool Noses and accessories. (See page 2-26)
Length
"B"
Max.
Stroke
Thread Description
Part No.
Oil Hole
9”
4”
.5625”-18 Internal Thread with
(229mm) (103mm) Counterbore and 118° Angle
382599
Oil Hole
9”
4”
.625”-18 Internal Thread with
(229mm) (103mm) Counterbore and 118° Angle
382346
Solid
9”
4”
No. 2 Short Morse Taper with
(229mm) (103mm) Side Knock-Out
382628
䡵 Nose Indexers - For 1.5625”-20 nose threads use 381326; For 2.25”20 use 381327 + 615705 Nose Adapter.
New Design for 1.5625-20: 641261; 2.25-20: 641262
䡵 When adapting a 3-jaw chuck to .5625 - 18 Internal Thread Spindle,
order Chuck Adapter (623643) for .375” cap. chuck OR Chuck
Adapter (619400) for .5” cap. chuck. (See page 2-24).
䡵 Fluid Swivels used with oil hole spindles and selection of Fluid
Chucks. (See page 2-25)
䡵 Other Noses & Spindles are available at extra charge. (See pg. 2-26)
2-19
Right Angle Tools
230QGDA-RAC-SU-MS
Depth and Dwell Attachment
The Quackenbush Depth Control or Countersink Attachment is a
high quality, precision attachment for the 230 Series Positive Feed
Drill which is used to precisely control the depth of drilled and
reamed, straight or tapered holes on both flat or contoured surfaces.
The attachment is also used for precision countersink
operations.This attachment has been proven on the most
demanding hole preparation jobs in the aircraft industry, and has
earned the reputation for producing exceptionally high quality holes
with precise depth accuracy, roundness and a high level of finish.
How the depth and dwell attachment operates
䡵 Start
Threaded to the end of the Depth and Dwell
Attachment is a DRILL BUSHING ➂ which is used to
secure the unit to the tooling fixture ➁. A tubular
SENSING SLEEVE ➅ is piloted by and slides axially
inside the DRILL BUSHING ➂. The SENSING SLEEVE
surrounds and pilots the CUTTER ➆ and the SPINDLE
➇. It is SPRING ➃ biased to engage the WORKPIECE
➀ and seat against it ➄. The primary function of the
SENSING SLEEVE is to provide a positive, definite
stopping surface that is a precise repeatable distance
from the workpiece.
䡵 Finish
Attached to SPINDLE ➇ is a patented micrometer
type, ADJUSTABLE ROTATING STOP ➈ with a selfcontained anti-friction bearing designed to engage the
SENSING SLEEVE when the CUTTER has achieved
the desired depth.
Once the pre-determined depth has been reached,
the advancement of the CUTTER is stopped by the
engagement of the ADJUSTABLE STOP on the
SPINDLE contacting the SENSING SLEEVE. This
allows the CUTTER to dwell (continue rotation without
further feed) and produce the desired hole
characteristics.
The Model 230 Right Angle Drill (furnished under
separate order) features automatic thrust activated
retract, torque overload shear pin, and automatic
motor stop after retract.
When mounted on the Model 230 Right Angle
Positive Feed Drill, the common SPINDLE ➇ extends
through and is driven by the right angle drill head.
Spindles (up to 15” long) will be hollow for coolant flow. A fluid
inducer (Part No. 381213) may be purchased for the remote end of
the spindle. Rear spindle guards must be used on all applications.
NOTE: Models designed for 1.186 maximum diameter cutters are
common. Larger units for 1.750 maximum diameter cutters are
available. Shortened models are available for short strokes in
confined work areas.
2-20
Right Angle Tools
Depth and Dwell attachments are designed for
each tooling application. The following
information is required in order to obtain a
quotation from the factory, Contact your local
Quackenbush Specialist for assistance.
➀
➁
➂
➃
➄
➅
Stand Off:––––––––––––––– inches. (Minimum chip clearance .375”)
Drill Bushing Tip Outside Diameter: ______________________________ inches.
Drill Bushing Series (Circle One):
• 2 Lock — 22,000, 23,00 & 24,000 Series
• 3 Lock — 25,000, 26,000 Series
Cutter Information:
• Style (reference drawings at bottom of this page):__________________________________.
• Furnish cutter Drawing or Dimensional Data (reference drawings at bottom of this page)
A ______________ F ______________
B ______________ T ______________ External Thread
C ______________ or
D ______________ T ______________ Internal Thread
E ______________ Fluid Spindle: Yes ____ No ____
Nose Indexer: Yes_____ No_____
Quackenbush Tool Model No. ___________________________________________________________________.
NOTE: • Important— If chip escape reliefs are required on the sensing sleeve, they must be specified when
ordering. A drawing must be provided showing the exact location and type openings required.
• Some applications involving long cutters require that the tips of the cutter extend beyond the Dwell and
Depth Attachment when the spindle is fully retracted.
COUNTERSINK
STYLE BR MODIFIED
STYLE AR
STYLE BR
INTERNAL THREAD
FOR OTHER CUTTER STYLES, FURNISH CUTTER DRAWING
2-21
Right Angle Tools
230QGDA-RAD-GD Gun Drill Series
Capacity:
Aluminum – .75” (19.1mm)
Stroke:
Min. – .125” (3.2mm)
Max. – Unlimited
230QGDA-RAD-GD WITH OPTIONAL NOSE
INDEXER AND VACUUM NOSE
䡵 230 series motor develops 2.30 nominal horsepower.
䡵 Easily adapted to oil hole with the use of an oil hole
spindle and a fluid swivel.
䡵 Automatic retract after hole depth has been reached.
䡵 Single push-button starts motor and engages drill
feed mechanism.
䡵 Adjustable retract stop with protective clutch
prevents jamming of spindle at end of retract cycle.
䡵 Auxiliary manual retract lever.
䡵 Rapid spindle retract.
䡵 Spindle continues to rotate in forward direction during
retract to eliminate withdrawal spiral.
䡵 Motor shuts off automatically after retract.
䡵 Swivel vacuum noses are also available.
䡵 Externally replaceable shear pin provides gear
protection if chips pack or cutter binds.
䡵 Steel gear housing for greater durability.
Model
230QGDA-RAD-GD
Motor
Configuration
Maximum Stroke
Right Angle
No Limit
in.
mm
Weight*
kg
in.
mm
13.25
5.95
15 7/8
403.23
*Weight is tool without spindle and nose piece.
Rated tool performance at 90 PSIG measured at tool inlet with motor running.
When selecting speeds and feeds, see page I-5.
Mist lubricator (631298) may be ordered.
2-22
Maximum Length
lbs
Spindle
Speeds
1500, 1850,
2100
Feed Per
Revolution
.0005, .001
SEE PAGES I-11–I-13 FOR SAFETY PRECAUTIONS.
SEE PAGE 2-22 – 2-25 FOR TOOLING ACCESSORIES.
Inlet
Minimum
Hose Size
.5” NPT
.5”
Right Angle Tools
Overall Length A Part Number Drill Bushing Thread Size B
7.50
8.50
9.50
11.50
7.50
8.50
9.50
11.50
8.50
STANDARD SPINDLE
631300
631301
631302
631303
631304
631305
631306
631359
631485
1.250-12
1.250-12
1.250-12
1.250-12
1.500-12
1.500-12
1.500-12
1.500-12
2.000-16
L.H.
L.H.
L.H.
L.H.
L.H.
L.H.
L.H.
L.H.
L.H.
SPINDLES (Select One)
Spindle
Type
Length
"B"
Max.
Stroke
Thread Description
Part No.
Oil Hole
9.25”
4.5”
.5625”-18 Internal Thread with
(235mm) (114mm) Counterbore and 118° Angle
623955
Oil Hole
9.25”
4.5”
.625”-18 Internal Thread with
(235mm) (114mm) Counterbore and 118° Angle
615964
䡵 Nose Indexer - 1.5625”-20 (381326)
䡵 Fluid Swivels used with oil hole spindles and selection of Fluid Chucks. (See page 2-25)
䡵 Other Noses and Spindles are available at extra charge. (See page 2-26)
2-23
Right Angle Tools Accessories
Accessories for the No. 15 and 140 Series Right Angle Drills
Bushing
Thread
.75 - 16 L.H.
1” - 14 L.H.
1.25” - 12 L.H.
Bushing
Thread
.75 - 16 L.H.
1” - 14 L.H.
1.25” - 12 L.H.
1.5” - 12 L.H.
2-24
S125 Series
Dim A
Part No.
5.3125 in.
619143
(135mm)
5.4375 in.
619142
(138mm)
5.4375 in.
619271
(138mm)
S150 Series
Dim. A
Part No.
5.625 in.
619662
(143mm)
5.875 in.
619683
(149mm)
5.875in.
619704
(149mm)
_
_
S300 Series
Dim. A
Part No.
6.9375 in.
619333
(176mm)
6.9375 in.
619297
(176mm)
6.9375 in.
619274
(176mm)
S275 Series
Dim. A
Part No.
6.875 in.
619954
(175mm)
7.125in.
619955
(181mm)
7.125 in.
619953
(181mm)
7.125in.
617802
(181mm)
Right Angle Tools Accessories
Accessories for the No. 158 and 230GD Series Right Angle Drills
Bushing
Thread
.75” - 16 L.H.
1” - 14 L.H.
1.25” - 12 L.H.
1.5” - 12 L.H.
Bushing
Thread
1” - 14 L.H.
1.25” - 12 L.H.
1.5” - 12 L.H.
2” - 16 L.H.
S150 Series
Dim. A
Part No.
5.625 in.
619662
(143mm)
5.875 in.
619683
(149mm)
5.875 in.
619704
(149mm)
_
_
S400 Series
Dim. A
Part No.
9.5 in.
621236
(241mm)
9.5 in.
621237
(241mm)
9.5 in.
621238
(241mm)
9.375 in.
614751
(238mm)
Bushing
Thread
1” - 14 L.H.
1.25” - 12 L.H.
1.5” - 12 L.H.
2” - 16 L.H.
S275 Series
Dim. A
Part No.
6.875 in.
619954
(175mm)
7.125 in.
619955
(181mm)
7.125 in.
619953
(181mm)
7.125 in.
615627
(181mm)
S600 Series
Dim. A
Part No.
11.5 in.
621244
(292mm)
11.5 in.
621245
(292mm)
11.5 in.
621246
(292mm)
11.375 in.
614757
(289mm)
S700 Series
Dim. A
Part No.
13.5625 in.
621228
(344mm)
13.5625 in.
621229
(344mm)
13.5625 in.
621230
(344mm)
13.4375 in.
614749
(341mm)
2-25
Right Angle Tools Accessories
Accessories for the No. 230 B & RA Series Right Angle Drills
Bushing
Thread
1” - 14 L.H.
1.25” - 12 L.H.
1.5” - 12 L.H.
2” - 16 L.H.
2-26
S400 Series
Dim. A
Part No.
9.5 in.
661236
(241mm)
9.5 in.
621237
(241mm)
9.5 in.
621238
(241mm)
9.375 in.
614751
(238mm)
S600 Series
Dim. A
Part No.
11.5 in.
621244
(292mm)
11.5 in.
621245
(292mm)
11.5 in.
621246
(292mm)
11.375 in.
614757
(289mm)
Right Angle Tools Accessories
End Feed
Side Feed
Quackenbush
Drill*
S-125, S-300
S-265
S-150, S-275
S-400, S600
S-400, S600
S-400, S600
S-700, S750
Bore
Dia.
Part No.
250
.375
.500
.500
.750
1.000
1.000
621373
621374
621375
621376
621377
621378
621408
Side Feed
"X"
1.510
1.510
1.510
1.510
1.510
1.510
1.510
"Y"
"Z"
Part No.
2.031
2.031
2.031
2.406
2.406
2.406
2.406
.375-24
.375-24
.375-24
.5625-18
.5625-18
.5625-18
.75-16
621389
621390
621391
621392
621393
621394
621395
End Feed
"X"
1.000
1.000
1.000
1.437
1.687
1.687
1.687
"Y"
"Z"
2.312
2.312
2.312
3.000
3.000
3.000
3.000
.375-24
.375-24
.375-24
.5625-18
.5625-18
.5625-18
.75-16
*Stroke length. Note: Dimensions X & Y are reference.
15 Series Swivel
Quackenbush Drill
15 QDA-RA-SU
158QGDA-RA-SU
230QGDA-RA-SU-MS
158 Series Swivel
230 Series Swivel
Model
Part No.
A
B
C
ALL MODELS
18 TPI SPINDLES
12.5 TPI SPINDLES
631256
621448
381213
.4375
.625
1.5625
1.5
1.5
1.75
.7813
.8125
.5
NOTE: Thread size for fluid line for all chucks and swivels is .125-27 NPT.
2-27
Right Angle Tools Accessories
Nose Indexers for the 15, 158 & 230 Series Right Angle Drills
These new indexers eliminate the need to relocate lock screws on the fixtures, or shim nose pieces in order to orientate the
tool to fit the application. An indexer aids in applying a right angle tool in confined spaces, and on applications where multiple
tools are used in close proximity. The tool is orientated to the desired position by depressing a spring loaded lever, which
allows the nose to rotate and lock without changing the position of the tool.
As an accessory for a new 15 series right angle tool, use part number 641244. To retrofit a previously purchased tool use part
number 641245. Either indexer adds approximately 1 3/8” of length to the tool.
158 right angle tool indexer is part number 641260. This is the same basic indexer used with the 230 series except for the
thread adapter (632684) and the retainer block (632691). The 632684 adapter allows the indexer to be attached directly to the
1 9/16-20 internal threads in the head of the tool. Therefore, if the tool has a 614228 adapter for the 2 1/4-20 nose threads,
simply remove the 614228 adapter before installing the indexer. The 641260 indexer adds approximately 2 3/8” of length.
There are two adapters for the 230 series because the 230 series comes with either the 1 9/16-20 or the 2 1/4-20 nose
attachment threads. Use indexer 641261 for a tool with the 1 9/16-20 internal threads in the tool. The 641261 indexer adds
approximately 2” of length. Use indexer 641262 for a tool with the 2 1/4-20 external threads. The 641262 indexer adds
approximately 2 1/4” of length.
The indexers are basically the same except the 641262 requires the 632685 thread adapter and the 632693 retainer block.
Both indexers are designed to acccommodate noses with either the 1 9/16-20 or 2 1/4-20 attachment threads.
Quackenbush Drill
15QDA-RAB-SU-RS
15QDA-RAB-SU-RS
158QGDA-RAD-SU-RS
230QGDA-RA-SU-MS
Model
Part No.
Length
New
Retrofit
1 9/16-20
2 1/4-20
641244
641245
641261
641262
1 3/8”
2 3/8”
2”
2 1/4”
641244
641260
641245
641261
641262
2-28
Right Angle Tools Accessories
Lubricators
631800 –
Manual Fill
Standard Capacity
Model
10QNPD
15QNPD
631887
631885
15SC
136SC
120SC
180SC
631881
631878
641109
641109
15QDA
140QGDA
158QGDA-15RAB
158QGDA
230QGDA
631799 –
Manual Fill
Large Capacity
631801 –
Pressure Fill
Standard Capacity
631802 –
Pressure Fill
Large Capacity
22007057 –
Recoules
Pump Luber
Micro-Pump
Adapter Kit
631888
631886
631883
641081
641081
631882
631879
641110
641110
631884
631880
641082
641082
631889
641047
NEW #
631930
641038
641160
641552
120QP
92050129
680209
92050128
932QR/942QR Micropumps/Counters
Tool Model
Description
932QR/942QR Micro-Pump with manual counter
932QR/942QR Micro-Pump without counter
932QR/942QR Manual Counter
Part Number
22007057
22007067
22008167
2-29
Right Angle Tools Accessories
How to order Spindles for Right Angle Tools
INFORMATION REQUIRED TO ORDER SPINDLES:
➀ OVERALL LENGTH:
Stroke
Stroke
Stroke
Stroke
Stroke
Stroke
__________
__________
__________
__________
__________
__________
+
+
+
+
+
+
2.87”
3.50”
3.75”
4.93”
4.75”
4.93”
(73mm) for 15QDA-RA = __________ Overall Length
(89mm) for 140QGDA-RA-SU-MS = __________ Overall Length
(95mm) for 158QGDA-RA = __________ Overall Length
(125mm) for 230QGDA-RA-MS = __________ Overall Length
(121mm) for 230QGDA-RA-GD = __________ Overall Length
(125mm) for 230QGDAB-MS = __________ Overall Length
➁ STANDARD SPINDLE THREAD RELIEF
➃
.875” for 15QDA-RA and 140QGDA-RA
1” for 158QDA-RA
(.5625” flange width for 230QGDA-RA-MS)
1” for 230QDA-RA-GD
NOTE: Specify if Thread Relief is other than standard.
➂ OIL HOLE REQUIRED?
䡺 Yes
䡺 No
NOTE: Spindle guards are highly recommended and are
available for all spindles. Please specify when ordering.
END PREPARATION OF SPINDLE:
䡺 INTERNAL THREAD:
(Provide drawing specifying thread, depth, angle and
counterbore depth if required)
䡺 STRAIGHT BORE:
Bore Diameter ____________ inches
Depth ___________________ inches
䡺 INTERNAL MORSE TAPER (for 158 and 230 Models only)
No. 1 Morse Taper 䡺
No. 2 Morse Taper 䡺
How to order Tool Noses for Right Angle Tools
INFORMATION REQUIRED TO ORDER TOOL NOSES:
➀
TOOL SERIES
䡺 15QDA-RA (1”-20 Nose Thread)
䡺 158QGDA-RA (1.5625”-20 OR 2.25”-20 Nose Thread)
䡺 230QGDA-RA-MS (1.5625”-20 OR 2.25”-20 Nose Thread)
䡺 230QGDA-RA-GD (1.5625”-20 OR 2.25”-20 Nose Thread)
➁ DIAMETER
Standard Sizes - 1.1875” OD
15QDA-RA - 1.5625”, 2” and 2.375” OD
230QGDA-RA-MS - 1.5625”, 2” and 2.375” OD
230QGDA-RA-GD - 1.56256”, 2” and 2.375” OD
DRILL BUSHING
BUSHING
SERIES
QUACKENBUSH NOSE
THREAD (ID)
21000
22000
23000
24000
25000
.75” - 16
1” - 14
1.25” - 12
1.5” - 12
2” - 16
Bushings are not furnished with
Quackenbush Tools.
➂ OVERALL LENGTH
➃ DRILL BUSHING SERIES
NOTE: Drawings for special tool noses must be provided when ordering.
2-30
Notes
2-31
Cooper Power Tools
P.O. Box 1410
Lexington, SC 29071-1410
USA
Phone: 800-845-5629
Fax: 803-359-0822
Cooper Power Tools
5925 McLaughlin Road
Mississauga, Ontario
Canada L5R 1B8
Phone: (905) 501-4785
Fax: (905) 501-4786
Cooper Power Tools
de México S.A. de C.V.
Libramiento La Joya No. 1
Bodega No. 2
Esq. Politécnico
Barrio San José
Cuautitlán, Edo de México
C.P. 54870
Phone: (011) 525 5899 9510
Fax: (011) 525 5870 5012
Cooper Tools Industrial Ltda.
Av. Liberdade, 4055
Zona Industrial - Iporanga
18087-170 Sorocaba, SP
Brazil
Tel: +55-15-3238-3929
Fax: +55-15-228-3260
Cooper Power Tools SAS
Zone industrielle – B.P. 28
77831 Ozoir-la-Ferrière Cedex
France
Téléphone: +33-1-6443-2200
Téléfax: +33-1-6440-1717
Cooper Tools Hungária Kft.
Berkenyefa sor 7
H-9027 Györ
Hungary
Tel: +36 96 505 300
Fax: +36 96 505 301
Cooper Power Tools
GmbH & Company
Postfach 30
D-73461 Westhausen
Germany
Phone: +49-7363-810
Fax: +49-7363-81222
Cooper (China) Co., Ltd.
18th Floor Yu An Building
738 Dongfang Road
Pudong, Shanghai 200122
China
Phone: +86 21 5831 6805
Fax: +86 21 5831 6762
Visit us online at www.cooperpowertools.com
SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE. © 2006 COOPER INDUSTRIES, INC. PRINTED IN USA.
AUGUST 2006
SP-1300-2-EN 0806 .25M