Vitek VTD-AR2812/VB Specifications

Alpha Series Vandal
WDR Dome Cameras
VITEK
• 650 TV Lines of Resolution
• Hercules II DSP Engine
• 1/3” Sony SuperHAD II CCD
• 2.8~12mm IR Corrected DC Auto-Iris Lens
• Available with 35 IR LEDs (120’ Range)
• Advanced OSD Functions: WDR, 3D DNR, DSS,
DIS, Sens-up, Motion Detection, Privacy
• IP68 Waterproof Rated
• Secondary Video Output with Cable Included
• 3-Axis Mount for Optimum Viewing Angle
• Dual Voltage 12VDC/24VAC Operation
BLACK
TABLE OF CONTENTS
BOX CONTENTS / MOUNTING ACCESSORIES
2-3
AVAILABLE MODELS
3
VTD-A2812/V INSTALLATION
4
VTD-AR2812/V INSTALLATION
5
INSTALLATION TIPS
6
OSD OPERATION
7-26
DIMENSIONS27
SPECIFICATIONS28-29
1
BOX
CONTENTS
BOX CONTENTS
CONTENTS
BOX
1)
Dome
Camera
1) Dome
DomeCamera
Camera
1)
BOX CONTENTS
1) Alpha
DomeAccessories
Camera
2)
Mounting
2)
Accessories
2) Mounting
Mounting
Accessories
2) Mounting
Accessories
3)
This
instruction
Manual
Mounting
Template
3) Secondary
VideoManual
Output
Cable
3)
&&
Mounting
Template
3) This
Thisinstruction
instruction
Manual
&
Mounting
Template
4) This instruction Manual & Mounting Template
MOUNTING ACCESSORIES
BOX
BOX
CONTENTS
BOX CONTENTS
CONTENTS
Self
Screws
Self Tapping
Screws
SelfTapping
Tapping
Screws
Self For
Tapping
Screws
For
the
housing
to atosolid
surface.
attaching
the base
housing
base
to surface.
a solid surface.
Forattaching
attaching
the
housing
base
a solid
For #:
attaching
the
housing
base to a solid surface.
Type
Phillips
ST4x30
Type
#:
Phillips
ST4x30
Type #: Phillips ST4x30
Qty:
4 #: Phillips ST4x30
Type
Qty: Qty:
4
4
Qty: 4
Secondary Video Output Cable
Secondary
VideoVideo
Output
Cable
Output
Cable
To
be Secondary
used with
a service
monitor
for adjusting
Secondary
Video
Output
Cable
Toangle,
be used
with
awith
service
monitor
for adjusting
be
used
a service
monitor
for adjusting
the
focus
and
To beToused
with
a zoom.
service
monitor
for adjusting
the angle,
focusfocus
and zoom.
the
angle,
and
zoom.
Qty:
1
the angle, focus and zoom.
Qty: Qty:
1
Qty: 1 1
Torx Wrench
Torx #:Wrench
Torx
Type
T20Wrench
Torx Wrench
Type
#:63mm
T20
Length:
Diameter: 4mm
Type
#: /T20
Type
#: 63mm
T20
Qty:
1 Length:
Length:
/ Diameter:
4mm 4mm
63mm
/ Diameter:
Length: 63mm
/ Diameter:
4mm
Qty: 1Qty: 1
Qty: 1
Dowels
IfDowels
necessary, use the dowels help secure the self tapping screws.
Length:
30mm /use
Diameter:
7mm help secure the self tapping screws.
IfDowels
necessary,
the dowels
Qty:
4
If
necessary,
the dowels
help secure the self tapping screws.
Length:
30mmuse
/ Diameter:
7mm
Length:
Qty:
4 30mm / Diameter: 7mm
Qty: 4
2
BLACK
Hex Wrench
If necessary,
Hex
Wrench use the wrench to help secure the surface mount.
If necessary, use the wrench help secure the surface mount.
Qty: 1
ConduitPlug
Plug
Conduit
Qty:
Qty:
11
AVAILABLE MODELS
AVAILABLE MODELS / ACCESSORIES
VTD-A2812/VW
VTD-AV4F/IB
/ VTD-AV4F/IW
Vandal
Resistant High
Resolution WDR Varifocal Dome Camera with
White Base.
620TVL Vandal Color Dome Camera with Fixed Lens.
VTD-A2812/VB
Vandal Resistant High Resolution WDR Varifocal Dome Camera with
Black
Base.
VTD-AV2812/IB
/ VTD-AV2812/IW
VTD-AR2812/VW
620TVL Indoor Color Dome Camera with 2.8~12mm DC Auto Iris Lens.
Vandal Resistant High Resolution Infrared WDR Varifocal Dome
Camera with White Base.
VTD-AVR2812/IB / VT-AVR2812/IW
VTD-AR2812/VB
Vandal Resistant High Resolution Infrared WDR Varifocal Dome
620TVL
Color Dome Camera with 2.8~12mm DC Auto Iris, IR
Camera
withIndoor
Black Base.
Corrected Lens & 35 IR LEDs.
3
VTD-A2812/V INSTALLATION
* See Installation Tips on page 6
4
BLACK
VTD-AR2812/V INSTALLATION
* See Installation Tips on page 6
5
INSTALLATION TIPS
1.) Power Consumption - Amperage/Voltage
It is of utmost importance that the proper Voltage and Amperage is used
when applying power to your VITEK Alpha Series Dome Camera. They
can be powered by either 12V DC or 24V AC. Always use a UL Listed
power transformer. The Amperage must be measured at the camera
location. It is very important that the camera receives no less than
the required Amperage or it will be “Starved” and eventually die out.
Cameras with Infrared LEDs require substantially more Amperage than
others so please refer to the Specifications (page 24-26) for the camera
you are installing.
2.) Extending the Power:
The cable may be extended up to 100 feet by using 18 Gauge (or
thicker) stranded wire - possibly longer depending on the amperage of
the transformer (see appropriate electrical guides to determine resistance). Simply cut the power connector off of the transformer and splice
the wire using a wire nut or solder and Electrical tape for isolation. DO
NOT ALLOW THE BARE WIRES TO TOUCH ONE ANOTHER.
3.) Extending the Video Cable
Always use 75 ohm copper braid coax (RG59U or thicker) for video signal transmission up to 500 feet - possibly longer depending on the grade
of cable and percentage of braid. VITEK Alpha Series Dome Cameras
utilize BNC Video connectors which come in male or female in order
to extend the coax to the desired distance (see appropriate installation
guide to learn how to properly install a BNC Connector).
6
BLACK
OSD OPERATION
SETUP MENU
EXPOSURE
LENS AGC SENSE-UP
WHITE BALANCE
AWB MODE R-Y GAIN B-Y GAIN RETURN
DAY&NIGHT
D&N MODE BURST C_SUP A_SUP DYNAMIC IR RETURN
IMAGE ADJUST
MIRROR SHARPNESS GAMMA LSC MONITOR RETURN
MOTION
MOTION AREA SENSITIVITY DISPLAY HOLD TIME
ALARM OUTPUT RETURN
PRIVACY
MASK1 MASK2 MASK3 MASK4 MASK5 MASK6
MASK7 MASK8 RETURN
SPECIAL
LANGUAGE TITLE COMMUNICATION DPC
FACTORY SET RETURN
EXIT
7
BACKLIGHT 3D-DNR RETURN
OSD OPERATION
Push to Setup
Secondary Video Output
8
BLACK
OSD OPERATION
MAIN MENU
EXPOSURE
WHITE BALANCE
DAY&NIGHT
IMAGE ADJUST
MOTION
PRIVACY
SPECIAL
EXIT
9
OSD OPERATION
EXPOSURE
The EXPOSURE menus SHUTTER/IRIS controls, BLC, HLI, D-WDR, AGC and 3D DNR, will set SENSE-UP etc.
and it will be able to change a condition.
MAIN MENU
EXPOSURE
WHITE BALANCE
DAY&NIGHT
IMAGE ADJUST
MOTION
PRIVACY
SPECIAL
EXIT
EXPOSURE
LENS
AGC
SENSE-UP
BACKLIGHT
3D-DNR
RETURN
DC
DC
HIGH
AUTO
OFF
AUTO
BRIGHTNESS
E.SHUTTER
RETURN
025
1/60
LENS
EXPOSURE – LENS – DC
DC modes use DC-IRIS lenses and they control AE. Then, electronic shutter speed default 1/60.
EXPOSURE – LENS – DC - BRIGTNESS
BRIGHT : Setting for target brightness.
Controls DC IRIS at the bright value which is set. Bright control from 1 to 100.
EXPOSURE – LENS – DC – E.SHUTTER
LENS – DC mode setting.
E.SHUTTER : Electronic shutter value setting mode in DC IRIS
1/60(1/50), 1/100, 1/120FLK, 1/250, 1/500,1/1000, 1/2000, 1/4000, 1/10000, 1/100000 sec. (default : 1/50 (1/60))
RETURN
10
BLACK
OSD OPERATION
EXPOSURE
LENS
AGC
SENSE-UP
BACKLIGHT
3D-DNR
RETURN
MANUAL
MANUAL
HIGH
AUTO
OFF
AUTO
BRIGHTNESS
E.SHUTTER
RETURN
025
AUTO
EXPOSURE – LENS
Selection of LENS modes.
The ELC means fixed LENS mode.
The ELC modes with electronic shutter AE controls.
When use DC-IRIS lens, DC-IRIS full open conditions.
DC modes use DC-IRIS lenses and they control AE. This time, Electronic shutter default shutter speed 1/60
EXPOSURE – LENS – MANUAL - BRIGHTNESS
BRIGHT : For target brightness control
AE controls this in compliance with a set bright control. Br ight control from 1 to 100.
EXPOSURE – LENS – MANUAL - E.SHTTER
E.SHUTTER
– setting value of electronic shutter
Select mode : Auto,1/60(1/50), 1/100, 1/120FLK, 1/250, 1/500,1/1000, 1/2000, 1/4000, 1/10000,
1/100000 sec. (default : AUTO)
When selecting in Auto mode (default) : The shutter mode from 1/60 to 1/100000 is controlled with automatic.
RETURN
AGC (Auto Gain Control)
EXPOSURE
LENS
AGC
SENSE-UP
BACKLIGHT
3D-DNR
RETURN
DC
HIGH
AUTO
OFF
AUTO
AGC : Auto Gain Control level set OFF / LOW / MIDDLE / HIGH.
11
OSD OPERATION
SENSE-UP/NIGHT WATCH DSS
EXPOSURE
LENS
AGC
SENSE-UP
BACKLIGHT
3D-DNR
RETURN
DC
HIGH
AUTO
OFF
AUTO
EXPOSURE – SENSE - UP
When it is low dark condition, SENSE UP uses
AUTO / OFF / X2 / X4 / X8 / X16 / X32 / X64 / X128 / X256 / X512 / X1024
AUTO mode basically sets X4 by manufacture.
In case of SENSE-UP operating, the 3D-DNR is operated LOW l evel.
BACKLIGHT
EXPOSURE
LENS
AGC
SENSE-UP
BACKLIGHT
3D-DNR
RETURN
DC
HIGH
AUTO
OFF
AUTO
12
BLACK
OSD OPERATION
BACKLIGHT - BLC (Back Light Conpensation)
EXPOSURE
LENS
AGC
SENSE-UP
BACKLIGHT
3D-DNR
RETURN
BLC
DC
HIGH
AUTO
BLC
AUTO
BLC - MANUAL
BLC MODE
BLC LEVEL
RETURN
MANUAL
MID
TOP
BOTTOM
LEFT
RIGHT
RETURN
005
010
005
010
EXPOSURE - BACKLIGHT – BLC – BLC MODE
Select AUTO or MANUAL
Sets the total AE level at AE value of select window area.
AUTO, the case which modes will select seeks the darkest are a with automatic and photometry weight,
AE controls does.
EXPOSURE - BACKLIGHT – BLC – BLC MODE - MANUAL
BLC window setting at manual mode
TOP / BOTTOM / LEFT / RIGHT zone setting.
TOP : 0 ~ (BOTTOM – 1), 1 step.
BOTTOM : (TOP + 1) ~ 16, 1 step.
LEFT : 0 ~ (RIGHT - 1), 1 step.
RIGHT : (LEFT + 1) ~ 16, 1 step.
EXPOSURE - BACKLIGHT – BLC – BLC LEVEL
BLC level select mode.
Select OFF / LOW / MID / HIGH
RETURN
13
OSD OPERATION
BACKLIGHT - HLC (High Light Conpensation)
EXPOSURE
LENS
AGC
SENSE-UP
BACKLIGHT
3D-DNR
RETURN
HLC
DC
HIGH
AUTO
HLC
AUTO
HBLC - MANUAL
HBLC
HLC LEVEL
MASK1
MASK2
MASK3
MASK4
RETURN
MANUAL
NIGHT
010
ON
ON
ON
ON
HBLC LEVEL
TOP
BOTTOM
LEFT
RIGHT
RETURN
MID
010
015
005
011
EXPOSURE - BACKLIGHT - HLC
It is a function which reverses the area about strong light.
The HLI BLC mode control by BLC window area. (HBLC)
EXPOSURE - BACKLIGHT - HLC - HBLC
Sets HBLC area of separate way from HLC mode
HBLC LEVEL : OFF / LOW / MID / HIGH
HBLC zone sets regulate HBLC zone with square window of the screen.
TOP / BOTTOM / LEFT / RIGHT control mode
TOP : 0 ~ (BOTTOM – 1), 1 step / BOTTOM : (TOP + 1) ~ 16, 1 step / LEFT : 0 ~(RIGH T – 1), 1 step /
RIGHT : (LEFT + 1) ~ 16, 1 step
EXPOSURE - BACKLIGHT - HLC - MODE
Use mode set of HLC (ALL DAY / NIGHT).
ALL DAY : Always operating HLC
NIGHT : Only NIGHT environment operating. But if DAY conditi on, not operating HLC
EXPOSURE - BACKLIGHT - HLC LEVEL
Setting of HLC level ( 1 ~ 100, 1 step, default : 10) Invers e zone will increase in low level
EXPOSURE - BACKLIGHT - HLC - MASK SEL
Window has 4 zones : MASK1 ~ 4 User sets each mask window.
TOP / BOTTOM / LEFT / RIGHT control mode
TOP : 0 ~ (BOTTOM – 1), 1 step / BOTTOM : (TOP + 1) ~ 34, 1 step / LEFT : 0 ~ (RIG HT–1), 1 step /
RIGHT : (LEFT + 1) ~ 45, 1 step
RETURN
14
BLACK
OSD OPERATION
BACKLIGHT - WDR (Wide Dynamic Range)
EXPOSURE
LENS
AGC
SENSE-UP
BACKLIGHT
3D-DNR
RETURN
WDR
DC
HIGH
AUTO
WDR
AUTO
SET LEVEL
RETURN
15
010
OSD OPERATION
BACKLIGHT - 3D DNR (3Dimension Digital Noise Reduction)
EXPOSURE
LENS
AGC
SENSE-UP
BACKLIGHT
3D-DNR
RETURN
DC
HIGH
AUTO
OFF
AUTO
AUTO : Level sets for 3D DNR.
OFF : 3D DNR function does not operate.
OFF / LOW / MID / HIGH. The noise level reduces in high level but ghost image increase more.
BACKLIGHT - RETURN
Select this to save the changes in the menu and return to the MAIN menu.
16
BLACK
OSD OPERATION
WHITE BALANCE
MAIN MENU
EXPOSURE
WHITE BALANCE
DAY&NIGHT
IMAGE ADJUST
MOTION
PRIVACY
SPECIAL
EXIT
WHITE BALANCE
MANUAL
128
128
AWB MODE
R-Y GAIN
B-Y GAIN
RETURN
WB-MANUAL
M-WR
M-WB
RETURN
064
064
WHITE BALANCE - AWB MODE
ATW : Auto Tracking White Balance mode
MANUAL : User can change color
M. WR : If it is higher than default (64), the white point moves toward RED. And it is lower than it moves toward GREEN.
Control range : 0 ~ 128, 1 step, default : 64
M. WB : If it is higher than default (64), the white point moves toward BLUE. And it is lower than it moves toward YELLOW.
Control range : 0 ~ 128, 1 step, default : 64
PUSH : When pushing ENTER, the white balance operate automatically in fixed color temperature area.
COLOR – R-Y GAIN
The color gain controls R-Y
If it increases more than default (128) value, R-Y gain extends to vertical shaft in color vector. And if it decrease,
it shortens ( 0 ~ 255, 1 step, default : 128)
COLOR – B-Y GAIN
The color gain controls B-Y
If it increases more than default (128) value, B-Y gain extends to horizontal shaft in color vector. And if it decrease,
it shortens ( 0 ~ 255, 1 step, default : 128)
RETURN : Select this to save the changes in the menu and return to the MAIN menu.
17
OSD OPERATION
DAY & NIGHT
MAIN MENU
EXPOSURE
WHITE BALANCE
DAY&NIGHT
IMAGE ADJUST
MOTION
PRIVACY
SPECIAL
EXIT
D&N MODE
DAY & NIGHT
DAY & NIGHT
D&N MODE
BURST
C_SUP
A_SUP
DYNAMIC IR
RETURN
AUTO
AUTO
OFF
020
020
AUTO
DAY > NIGHT
NIGHT > DAY
DELAY TIME
RETURN
042
035
010
DAY&NIGHT – D&N MODE - AUTO
D&N is decided by AGC gain level.
DAY>NIGHT: It controls gain level for changing Night mode ((DAY>NIGHT + 1) ~ 42, 1 step) unit dB.
NIGHT>DAY: It controls gain level for changing DAY mode. (3 5 ~ (NIGHT>DAY – 1), 1 step) unit dB.
DWELL TIME: D&N change on continual time condition set DAY>N IGHT or NIGHT>DAY.
For protecting hunting.( 0 ~ 15, 1 step) unit : sec
RETURN: Select this to save the changes in the menu and ret urn to the MAIN menu.
18
BLACK
OSD OPERATION
DAY&NIGHT – D&N MODE - COLOR : This picture is always displayed in color.
DAY&NIGHT – D&N MODE - B&W : This picture is always displayed in black and white.
You can turn on or off the burst signal on B/W mode.
DAY&NIGHT – D&N – EXT
DAY & NIGHT
D&N MODE
BURST
C_SUP
A_SUP
SMART IR
RETURN
EXT
EXT
OFF
020
020
AUTO
DAY > NIGHT
NIGHT > DAY
DELAY TIME
RETURN
EXT mode: D&N decision by external CDS signal.
DAY>NIGHT: ADC level for changing Night mode. (0 ~ 255, 1 step)
NIGHT>DAY : ADC level for changing Day mode. (0 ~ 255, 1 step)
BURST
DAY & NIGHT
D&N MODE
BURST
C_SUP
A_SUP
SMART IR
RETURN
AUTO
OFF
020
020
AUTO
BURST (AUTO) : When it is Night mode, color burst ON/OFF controls.
BURST (EXT) : When it is Night mode, color burst signal selects ON/OFF.
19
190
030
005
OSD OPERATION
C_SUP / A_SUP
DAY & NIGHT
D&N MODE
BURST
C_SUP
A_SUP
DYNAMIC IR
RETURN
AUTO
OFF
020
020
AUTO
DAY&NIGHT – C_SUP
The color noise suppress in Night mode / 0 ~100, 1 step. Unit %.
DAY&NIGHT – A_SUP
The Aperture level suppres in Night mode / 0 ~100, 1 step. Unit %.
DYNAMIC IR
Can adjust the display saturation as AUTO or OFF.
DYNAMIC IR - AUTO
DAY & NIGHT
D&N MODE
BURST
C_SUP
A_SUP
DYNAMIC IR
RETURN
AUTO
OFF
020
020
AUTO
LEVEL
RETURN
020
RETURN
Select this to save the changes in the menu and return to the MAIN menu.
IMAGE ADJUST
20
BLACK
OSD OPERATION
MAIN MENU
IMAGE ADJUST
EXPOSURE
WHITE BALANCE
DAY&NIGHT
IMAGE ADJUST
MOTION
PRIVACY
SPECIAL
EXIT
MIRROR
SHARPNESS
GAMMA
LSC
MONITOR
RETURN
OFF
015
0.45
OFF
LCD
MIRROR : Image change mirror ON/OFF mode
SHARPNESS : Sharpness level control ( 0 ~ 30, 1 step)
GAMMA
User can adjust GAMMA level.
Selecting of 0.45 / 0.60 / 1.0 / USER.
After selecting USER mode, the gamma value adjust 0.20 ~ 1.0 0. (0.05 step)
LSC (Lens Shading Compensation) : Lens Shading Compensation ON/OFF mode
n order to complement the quality of the lens is a function which increases
gain of screen a ngle. (0 ~ 30, 1 step.)
In increasing level, side image is bright.
MONITOR : The DISPLAY MONITOR mode can support two kinds of display (LCD/CRT)
RETURN : Select this to save the changes in the menu and return to the MAIN menu.
MOTION
21
OSD OPERATION
The function informs alarm on camera when being moving by the screen. The setting zones are 4 area.
MAIN MENU
MOTION
EXPOSURE
WHITE BALANCE
DAY&NIGHT
IMAGE ADJUST
MOTION
PRIVACY
SPECIAL
EXIT
MOTION
AREA
SENSITIVITY
DISPLAY
HOLD TIME
ALARM OUTPUT
RETURN
OFF
025
TRACE
003
OFF
MOTION : Select operates ON/OFF
MOTION
MOTION
AREA
SENSITIVITY
DISPLAY
HOLD TIME
ALARM OUTPUT
RETURN
MOT - AREA
OFF
025
TRACE
003
OFF
AREA1
AREA2
AREA3
AREA4
RETURN
AREA - ON
ON
ON
ON
ON
TOP
BOTTOM
LEFT
RIGHT
RETURN
015
050
030
080
AREA SEL : Select each area
MOTION – AREA SEL – AREA i
MASK MODE: Selected area operates MASK area.
TOP / BOTTOM / LEFT / RIGHT
TOP : 0 ~ (BOTTOM - 1), 1 step.
BOTTOM : (TOP + 1) ~ 145, 1 step.
LEFT : 0 ~ (RIGHT – 1), 1 step.
RIGHT : (LEFT + 1) ~ 192, 1 step
** NOTE: The ‘ALARM OUTPUT’ feature mentioned above is available by Special Order only.
22
BLACK
OSD OPERATION
MOTION
MOTION
AREA
SENSITIVITY
DISPLAY
HOLD TIME
ALARM OUTPUT
RETURN
OFF
025
TRACE
003
OFF
SENSITIVITY : Control MOTION sensitivity. (1 ~ 30, 1 step)
DISPLAY: Control alarm mode when MOTION indicates. ( Select of OFF / MESSAGE / TRACE)
i) MESSAGE mode: MOTION ICON display when MOTION indicates.
ii) TRACE mode: Display selected window in AREA
HOLD TIME: The time of alarm control when MOTION indicat. ( 1 ~ 15, 1 step ) Unit : sec
ALARM OUTPUT : Select operates ON/OFF
RETURN : Select this to save the changes in the menu and return to the MAIN menu.
** NOTE: The ‘ALARM OUTPUT’ feature mentioned above is available by Special Order only.
PRIVACY
The mask controls about the zone where the privacy is necessary. The total mask is 8 zones.
The each mask color can control GRAY, BLACK, WHITE, RED, GREEN, BLUE, MAGENTA, CYAN.
MAIN MENU
EXPOSURE
WHITE BALANCE
DAY&NIGHT
IMAGE ADJUST
MOTION
PRIVACY
SPECIAL
EXIT
23
OSD OPERATION
PRIVACY
MASK1
MASK2
MASK3
MASK4
MASK5
MASK6
MASK7
MASK8
RETURN
PRIVACY
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
MASK1
MASK2
MASK3
MASK4
MASK5
MASK6
MASK7
MASK8
RETURN
MASK ON
ON
ON
ON
ON
ON
ON
ON
ON
DOT SEL
DOT XY
MOVE XY
COLOR
RETURN
L_TOP
MAGENTA
PRIVACY – MASK1 ~ MASK 8
The each mask selects ON/OFF
PRIVACY – MASK
After selecting each mask, it can select color, location, area of mask.
DOT SEL : The each mask can change area.
(L_TOP / L_BOT / R_BOT / R_TOP)
DOT XY : The selected point in mask controls size.
MOVE XY : The selected mask can move.
COLOR SET : The selected mask can change color.
(GRAY / BLACK / WHITE / RED / GREEN / BLUE / MAGENTA / CYAN )
SPECIAL
MAIN MENU
SPECIAL
LANGUAGE
TITLE
COMMUNICATION
DPC
FACTORY SET
RETURN
EXPOSURE
WHITE BALANCE
DAY&NIGHT
IMAGE ADJUST
MOTION
PRIVACY
SPECIAL
EXIT
ENGLISH
OFF
ON
AUTO
NO
LANGUAGE : ENGLISH, SPANISH, FRENCH, PROTUGUESE, RUSSIAN, GERMAN, ITALIAN, DUTCH, KOREAN, CHINESE
** NOTE: The ‘COMMUNICATION’ feature mentioned above is available by Special Order only.
24
BLACK
OSD OPERATION
SPECIAL
LANGUAGE
TITLE
COMMUNICATION
DPC
FACTORY SET
RETURN
USER TITLE
ENGLISH
ON
ON
AUTO
NO
---------------------------
TITLE
User writes TITLE / User sets TITLE ON/OFF.
After selecting TITLE ON, it can write TEXT to diplay on screen.
USER TITLE – Text setting mode / User can write text 64 charaters.
← , → : When it modify, user can move revision text..
CLR: User can remove all text.
POS: The text move to the position.
RET : After finishing USER TITLE to the upper menu.
COMMUNICATION
SPECIAL
LANGUAGE
TITLE
COMMUNICATION
DPC
FACTORY SET
RETURN
COMMUNICATION
ENGLISH
OFF
ON
AUTO
NO
ID
BAUD RATE
PROTOCOL
RETURN
001
9600
PELCO - D
ID : When user set a couple of camera, it can set camera ID of each camera. 0 ~ 255
COMMUNICATION (communication setting) : User can set RS485 comm. ON/OFF.
Setting RS485 communication.
PROTOCOL: Supporting for PELCO-D.
BAUDRATE: 2400 / 4800 / 9600 / 19200. Unit : bps
** NOTE: The ‘COMMUNICATION’ feature mentioned above is available by Special Order only.
25
OSD OPERATION
DPC (Dead Pixel Conpensation)
It is the function to compensate for CCD defect. User can se lect OFF / MANUAL.
SPECIAL
LANGUAGE
TITLE
COMMUNL CATION
DPC
FACTORY SET
RETURN
DPC AUTO
ENGLISH
OFF
ON
AUTO
NO
WHITE THR
LUMA THR
RETURN
150
030
DPC – MANUAL
After selecting MANUAL mode, menu move to the DPC control mo de
WHITE THR : White defect threshold. (0 ~ 255, 1 step)
LUMA THR : Black defect threshold. (0 ~ 255, 1 step)
FACTORY SET : Factory initial data mode set.
Camera setting data factory original data.
After factory set mode, user has to enter SAVE&EXIT.
RETURN : Select this to save the changes in the menu and return to the MAIN menu.
EXIT
MAIN MENU
EXIT
EXPOSURE
WHITE BALANCE
DAY&NIGHT
IMAGE ADJUST
MOTION
PRIVACY
SPECIAL
EXIT
SAVE & EXIT
EXIT
RETURN
SAVE & EXIT
EXIT
RETURN
26
BLACK
DIMENSIONS
1.81”
(46mm)
5.85”
(148.6mm)
5.85”
(148.6mm)
3.29”
(83.5mm)
4.26”
(108.3mm)
2.4”
(61.1mm)
1.75”
(44.5mm)
1.81”
(46mm)
5.85”
(148.6mm)
5.85”
(148.6mm)
3.29”
(83.5mm)
4.77”
(121.2mm)
1.75”
(44.5mm)
27
2.4”
(61.1mm)
SPECIFICATIONS
VTD-A2812/V
Image Device
1/3” Sony SuperHAD II CCD
Resolution
650 TV Lines
Min. Illumination
0.1 Lux at F1.2 (Color) / 0.0001 Lux (Sense up x256)
Effective Pixels
811(H) x 508(V) 410K pixels
S/N Ratio
More Than 52dB (AGC Off)
Shutter
AUTO / MANUAL (1/60sec ~ 1/100,000sec)
White Balance
ATW / AWC / PUSH / MANUAL (Adjustable)
Standard Lens
2.8-12mm DC Auto Iris Lens
Video Output
CVBS: 1.0Vp-p / 75ohm
IP Rating
Power Source
IP68
Dual Voltage 12VDC/24VAC Operation
Power Consumption (12VDC)
120 mA
Power Consumption (24VAC)
Environmental
Dimensions
70 mA
14°F~122°F (-10°C~50°C) at 30%~80% RH
5.85” x 4.22” (148.48mm x 107.13mm)
Weight
2.19lbs (997g)
28
BLACK
SPECIFICATIONS
VTD-AR2812/V
Image Device
1/3” Sony SuperHAD II CCD
Resolution
650 TV Lines
IR LEDs
35 LEDs at 850nm
Min. Illumination
0 Lux (IR ON)
Effective Pixels
811(H) x 508(V) 410K pixels
S/N Ratio
More Than 52dB (AGC Off)
Shutter
AUTO / MANUAL (1/60sec ~ 1/100,000sec)
White Balance
ATW / AWC / PUSH / MANUAL (Adjustable)
Standard Lens
2.8-12mm IR Corrected DC Auto Iris Lens
Video Output
CVBS: 1.0Vp-p / 75ohm
IP Rating
Power Source
Power Consumption (12VDC)
IP68
Dual Voltage 12VDC/24VAC Operation
120 mA (IR LEDs Off) / 800 mA (IR LEDs On)
Power Consumption (24VAC)
70 mA (IR LEDs Off) / 500 mA (IR LEDs On)
Environmental
14°F~122°F (-10°C~50°C) at 30%~80% RH
Dimensions
5.85“ x 4.75” (148.48mm x 120.64mm)
Weight
2.44lb (1106.77g)
29
OPTIONAL CEILING MOUNTS
VT-AV/CMT
Heavy Duty ALPHA Series Ceiling Mount
• Compatible with the ALPHA Series Vandal Resistant Dome Cameras
• Available in Ivory and Black (VT-AV/CMT-W / VT-AV/CMT-B)
30
BLACK
OPTIONAL WALL MOUNTS
VT-AV/WMT
Heavy Duty ALPHA Series Wall Mount
• Compatible with the ALPHA Series Vandal Resistant Dome Cameras
• Available in Ivory and Black (VT-AV/WMT-W / VT-AV/WMT-B)
31
EHL SERIES DIGITAL RECORDERS
VT-EHL Series
4 & 8 Channel Digital Video Recorders
with H.264 Compression
H.264
Simplicity and reliability is the basis upon which the EH L Digital Video Recorder
was conceived. With almost every powerful feature of its predecessor the “EH”, the
EHL offers an economical option for providing the most advanced recording solution
available. As part of the EH family, the EHL is completely compatible with all VITEK
EH Platform application software.
• 4 or 8 Video Inputs with 1 Main, 1 Spot Monitor Output
and 1 VGA output.
• Real Time Recording with Up to 120 IPS at HD1
•
•
•
•
Recording / Live Display (VT-EHL4) / 240 IPS at CIF
(VT-EHL8)
H.264 Compression
500GB to 2TB Internal Storage Options
Remote Viewing over the Internet, LAN, Explorer, Safari,
Firefox, Opera and Chrome
iPhone, iPad, iTouch and Android Apps available
32
BLACK
NOTES
33
NOTES
34
BLACK
VITEK LIMITED PRODUCT WARRANTY
VITEK products carry a three (3) year limited warranty. VITEK warrants to the purchaser
that products manufactured by VITEK are free of any rightful claim of infringement or
the like, and when used in the manner intended, will be free of defects in materials and
workmanship for a period of three (3) years, or as otherwise stated above, from the
date of purchase by the end user. This warranty is nontransferable and extends only to
the original buyer or end user customer of a Vitek Authorized Reseller.
The product must have been used only for its intended purpose, and not been subjected to damage by misuse, wilful or accidental damage, caused by excessive voltage
or lightning.
The product must not have been tampered with in any way or the guarantee will be
considered null and void.
This guarantee does not affect your statutory rights.
Contact your local VITEK Reseller should servicing become necessary.
VITEK makes no warranty or guarantee whatsoever with respect to products sold or
purchased through unauthorized sales channels. Warranty support is available only if
product is purchased through a VITEK Authorized Reseller.
28492 CONSTELLATION ROAD VALENCIA, CA 91355
WWW.VITEKCCTV.COM | 888-VITEK-70