Wolf Warming drawer Use & care guide

WARMING DRAWER
USE & CARE GUIDE
GUÍA DE USO Y MANTENIMIENTO
GUIDE D’UTILISATION ET D’ENTRETIEN
INFORMAZIONI SU USO E MANUTENZIONE
BEDIENUNGS- UND PFLEGEANLEITUNG
Contents
Thank You
Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Your purchase of a Wolf warming drawer attests to the
importance you place upon the quality and performance of
your cooking equipment. We understand this importance
and have designed and built your warming drawer with
quality materials and workmanship to give you years of
dependable service.
Warming Drawer Features . . . . . . . . . . . . . . . . . . . . . . 4
Warming Drawer Use & Care . . . . . . . . . . . . . . . . . . . . 4
Service Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Before you begin using your warming drawer, please take
some time to read this use & care guide. It will be to your
benefit to familiarize yourself with the safety practices,
features, operation and care recommendations of the Wolf
warming drawer.
Features and specifications in this guide and on the website
are subject to change at any time without notice. Check
our website, wolfappliance.com, for the most up-to-date
specifications.
Important Note
To ensure the safe and efficient use of Wolf equipment,
please take note of the following types of highlighted
information throughout this guide:
IMPORTANT NOTE highlights information that is
especially important.
CAUTION signals a situation where minor injury or product
damage may occur if instructions are not followed.
WARNING states a hazard that may cause serious injury or
death if precautions are not followed.
WOLF® is a registered trademark of Wolf Appliance, Inc.
Safety Instructions
3
wolfappliance.com
IMPORTANT INSTRUCTIONS
IMPORTANT NOTE: Read all safety instructions before
using this appliance.
• Read this use & care guide carefully before using
your new warming drawer to reduce the risk of fire,
electric shock or injury to persons.
• Ensure proper installation and servicing. This appli-
ance must be properly installed and grounded by a
qualified technician. Have the installer show you the
location of the circuit breaker or fuse so that you
know where to turn off power.
• Before performing any service, unplug or disconnect
the power supply for the warming drawer by
switching off the circuit breaker or removing the
fuse.
GENERAL SAFETY REQUIREMENTS
• Ensure that towels are stacked only as high as the
sides of the drawer pan. Any higher may result in
discoloration of the towels.
• The purpose of the warming drawer is to hold hot
cooked foods at serving temperature and proof
yeast dough. Cold food cannot be heated thoroughly
or cooked in the warming drawer.
• Make sure the warming drawer is securely installed
in a firmly attached cabinet.
• Use care when opening the warming drawer. Par-
tially open the warming drawer and let warm air
escape prior to removing or replacing food.
• Always place the rack in the desired location while
the warming drawer is cool.
• Always use dry pot holders when removing items
from the warming drawer. Wet or damp pot holders
can cause burns. Do not use a towel or bulky cloth
in place of pot holders.
• Do not operate the warming drawer if the front panel
has not been installed.
• Do not repair or replace any part of the warming
drawer unless specifically recommended in literature
accompanying this appliance. All service should be
referred to a Wolf dealer.
• Do not leave children alone or unattended in the area
• Do not touch the heating element or the interior
surface of the warming drawer. These surfaces may
be hot enough to burn. The inside surfaces of the
warming drawer may be hot when opened.
• Do not heat unopened food containers. Pressure
could build up and the container could burst and
cause serious injury.
when the warming drawer is in use. Never allow
children to sit, stand or hide in the appliance. Do not
let children play with the warming drawer.
• Do not use aluminum foil to line the warming drawer.
• Never leave the warming drawer open when you are
• Do not overfill the warming drawer. This may lead to
not attending to the warming drawer.
• Never use the warming drawer or other appliances
This may cause damage to interior surfaces of the
warming drawer.
difficulty in opening or closing the drawer, as well as
items falling out of the drawer or behind the drawer.
for warming or heating the room.
• Do not wear loose fitting or hanging garments while
using this appliance.
• Do not place more than 34 kg into the warming
drawer.
• Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any other
appliance.
Do not use the warming drawer to dry paper
products. If overheated, paper products can catch
fire.
Warming Drawer Features
Warming Drawer Use & Care
Warming Drawer Features
Electronic Controls
• Optional stainless steel drawer fronts with handle
match the look of Wolf built-in ovens and sealed burner
rangetops.
• Optional integrated drawer front allows for custom
wood panel and handle.
• 850-watt heating element.
• Removable stainless steel drawer pan.
• Stainless steel interior with galvanized exterior.
The electronic touch control panel is hidden when the
warming drawer is closed. With the warming drawer open,
the controls can be accessed at the top of the drawer just
behind the drawer front.
• Optional six-piece container set with lids and rack
available as an accessory.
PRESETS
• Full-extension, ball bearing drawer glides.
• CE certified.
• Hidden electronic touch control panel.
4
• Preset and variable temperature control.
• Preset automatic shut-off or extended operation in
Sabbath mode.
This appliance is certified by Star-K to meet
strict religious regulations in conjunction with
specific instructions found on www.star-k.org.
Your warming drawer features four preset temperature
settings;
,
,
and
. Using the PRESETS
eliminates the need to manually set the temperature and
time.
Preset Temperature Settings
• Removable rack for stacking food.
PREHEAT
During preheat, the temperature read-out in the LCD
display alternates between the setpoint and the actual
temperature. The word “Lo” will appear in the LCD display
until the temperature reaches 29°C. The unit will beep
once to signal preheat is complete.
AUTOMATIC SHUT-OFF
Your Wolf warming drawer has a factory preset automatic
shut-off time of four hours. The time interval of the automatic shut-off can be adjusted from one minute to 24
hours.
29°C
48°C
71°C
93°C
TO SET AUTOMATIC SHUT-OFF:
1) Warming drawer must be OFF.
2) Touch
TO SET THE TEMPERATURE:
1) Touch
MODEL ICBWWD30
Removable stainless
steel drawer pan
Removable rack
for stacking food
Stainless steel
interior
Galvanized exterior
Hidden electronic
touch control panel
.
2) Touch one of the PRESETS;
,
,
or
or touch the
or
arrow pad. Touch the
arrow to increase the temperature and the
arrow to decrease the temperature. Two seconds after
selecting the temperature/time, the ON indicator will
illuminate as well as a beep indicating that the unit is
on.
.
3) Touch one of the PRESETS;
,
,
or
or touch the
or
arrow pad. Touch the
arrow to increase the temperature and the
arrow to decrease the temperature.
4) Touch and hold the
arrow to increase the shutoff time or the
arrow to decrease the
shut-off time.
5) The word TIMER will illuminate and the automatic
shut-off time will appear in the LCD display.
IMPORTANT NOTE: One of the PRESETS or the
or
arrow pad must be pressed within 20 seconds of
turning unit on, or the unit will automatically shut off.
Stainless steel drawer
front with curved handle
shown
Ball bearing
drawer glides
Location of
rating plate
LCD Display
Warming drawer control panel.
ON/OFF
control
Variable
temperature
controls
(UP and DOWN)
Preset
temperature
controls
Automatic
shut-off timer
adjustment
(UP and DOWN)
Warming Drawer Use & Care
5
wolfappliance.com
Electronic Controls
Sabbath Mode
Control Panel Backlighting
Before Using for the First Time
PRESET PROGRAMMING
Sabbath mode is for certain religious observances where
some warming drawer functions need to be turned off. In
Sabbath mode, the automatic shut-off feature is disabled,
allowing the warming drawer to operate continuously.
The Wolf warming drawer has three options for control
panel backlighting; backlight off in Sabbath, backlight on
in Sabbath and backlight off in all modes. The backlight
defaults to ON in normal use and OFF in Sabbath mode.
Remove all literature and packaging materials from inside
the warming drawer.
TO INITIATE SABBATH MODE:
TO CHANGE CONTROL PANEL BACKLIGHTING:
1) Warming drawer must be OFF.
1) Warming drawer must be OFF.
2) Touch and hold
for 5 seconds. The word “Sab”
will flash in the LCD display after 5 seconds.
2) Touch and hold
arrow and
arrow for 5
seconds. The current backlight setting will appear in
the LCD display.
Preset temperatures and time settings can be adjusted for
the
,
,
and
PRESETS.
The
and
temperature range is 26–43°C. The
,
PRESETS can be adjusted from 26–93°C.
TO ADJUST PRESET TEMPERATURE AND TIME SETTING:
1) Warming drawer must be OFF.
2) Touch
.
3) Touch and hold the desired PRESET,
,
,
or
for 5 seconds. The word TIMER will illuminate
and “4:00” will flash in the LCD display along with the
temperature. Adjustments to the settings should be
made within 30 seconds. The unit will exit the preset
programming mode if no adjustment is made within
this time.
4) To adjust the temperature, touch and hold the
arrow to increase or the
arrow to decrease the
temperature until the desired preset temperature is
shown in the LCD display.
5) To adjust the time setting, touch and hold the
arrow to increase or the
arrow to decrease the
time until the desired preset time setting is shown in
the LCD display.
6) Touch and hold the adjusted PRESET again for 5
seconds. Three quick tones will signify that settings for
the PRESET have been changed. If 30 seconds elapse
before you touch and hold the PRESET, the unit will
exit the preset programming mode with no adjustments
made.
3) While “Sab” is flashing, select one of the PRESETS or
set the temperature with the
or
arrow
pads. Touch the
arrow to increase the temperature and the
arrow to decrease the temperature.
Two tones will signify that the Sabbath mode has been
initiated.
4) In Sabbath mode, the warming drawer will operate
continuously until
is touched. The word ON will
remain illuminated in the LCD display all the while the
unit is in Sabbath mode. No other read-outs will
appear in the LCD display.
5) Touch
to shut off the warming drawer and exit
Sabbath mode.
When Sabbath mode is initiated, the automatic shut-off
is disabled, requiring the unit to be turned off manually
by touching
.
3) Use the
arrow to scroll through the three backlight options; backlight off in Sabbath, backlight on in
Sabbath (50% power), and backlight off in all modes. A
selection should be made within 30 seconds. The unit
will default to the current backlight setting if a new
selection is not made within this time.
4) With the desired backlight setting selected, touch
to save the setting.
Temperature Display
The warming drawer temperature display can be changed
from Fahrenheit (F) to Celsius (C) or vice versa.
TO CHANGE TEMPERATURE DISPLAY:
1) Warming drawer must be OFF.
2) Touch and hold both the
seconds.
and
arrows for 5
3) After 5 seconds, the unit will beep, the backlighting will
turn on, and either F or C will appear, depending on the
current display setting.
4) Touch the
or
arrow to select either
Fahrenheit (F) or Celsius (C).
5) With the desired temperature display selected, touch
to save the setting.
Clean your warming drawer thoroughly with hot water and
a mild detergent. Rinse and dry with a soft cloth. This
removes residual oil and grease left on the surface from
the manufacturing process.
Apply a stainless steel polish to protect the finish and add
luster to the exterior of your warming drawer. Refer to
cleaning and care recommendations on page 7.
Warming Drawer Use & Care
6
Using the Warming Drawer
Warming Drawer Rack
Food Preparation
• Always start with hot food. The warming drawer will
keep hot food at serving temperature. Do not use the
warming drawer to heat cold food other than for
proofing yeast dough and crisping crackers, chips or
dry cereal.
The rack will fit in the warming drawer front to back and
allows you to double stack items.
TO PROOF YEAST BREAD DOUGH:
TO WARM TOWELS:
1) Touch
then
on the control panel. “29C” will
appear in the LCD display. The word TIMER will illuminate and “4:00” will flash in the LCD display. Allow the
warming drawer to preheat.
1) Preheat warming drawer on
• Always preheat the warming drawer. Preheat 3 minutes
for
, 4 minutes for
, 7 minutes for
and
13 minutes for
.
• Food in heat-safe glass and glass ceramic containers
may need higher temperature settings as compared to
food in metal containers.
• Repeated opening of the warming drawer will allow hot
air to escape and the food to cool.
• With large loads, it may be necessary to use a higher
temperature setting and to cover some of the cooked
food items.
• Food should be kept hot in the cooking container or
transferred to a heat-safe serving dish prior to being
placed into the warming drawer.
• Remove serving spoons, etc., before placing food containers in warming drawer.
When holding hot, cooked foods and warming empty
serving dishes at the same time, place the serving dishes
on the bottom of the warming drawer and place food on
the rack.
IMPORTANT NOTE: Always preheat the warming drawer
with the rack in position.
Warming Drawer Pan
The stainless steel warming drawer pan is removable for
cleaning. To remove, pull the warming drawer completely
open. Slide fingertips under the right and left side edges
of the pan. Firmly pull the pan upward, making sure that
all edges are clear from the interior of the unit.
To replace the warming drawer pan, pull the warming
drawer completely open. The pan should be inserted so
that the rear wall has the holes for the fan. Place pan
edges on the side rails of the drawer frame. Open and
close the drawer completely to check operation.
2) The temperature can be adjusted by pressing the
or
arrows. The time setting can be adjusted
by pressing the
or
arrows.
3) Lightly oil the top of the dough in a bowl large enough
to allow the dough to double in size.
.
2) Place towels in warming drawer.
IMPORTANT NOTE: Ensure that towels are stacked only as
high as the sides of the drawer pan. Any higher may result
in discoloration of the towels.
IMPORTANT NOTE: Towels should be warmed on the
setting only. Any other settings may result in discoloration of the towels.
4) Cover the dough with a dry cloth.
5) Place bowl on the bottom of the warming drawer.
6) Let dough rest in warming drawer for 40 minutes or
until dough has doubled in size and a slight depression
remains in the surface of the dough when touched
gently with a finger.
.
2) Place food in shallow dish or pan.
• Aluminum foil may be used to cover food to increase
moisture content.
3) Check for desired crispness after 45 minutes. Adjust
time if necessary.
• Do not place plastic containers or plastic wrap in the
warming drawer.
TO WARM SERVING BOWLS:
1) Preheat warming drawer on
IMPORTANT NOTE: Leave food uncovered to keep food
crisp and cover food to keep moisture in.
Temperature Settings
Beef (rare)*, eggs, tortilla chips and towels
TO CRISP STALE ITEMS:
1) Preheat warming drawer on
Temperature Selection
.
2) Use only heat-safe dishes.
3) Place the empty dishes on the rack or bottom of the
warming drawer.
IMPORTANT NOTE: To heat fine china or heat dishes to a
higher temperature, please consult dish manufacturer for
maximum heat tolerance.
Beef (medium or well done)*, bread, soft rolls, hard rolls, fruit,
casseroles, cooked cereals, gravy, cream sauces, fish, seafood,
ham, pork, lamb, poultry, pancakes, waffles, pies (one or two
crusts), mashed potatoes and vegetables
Bacon, fried foods, hamburger, pizza (on plate or in box) and
baked potatoes (in foil)
*USDA/FSIS recommends an internal temperature of 60°C as the
minimum doneness for beef. Use a meat thermometer to check
internal meat temperatures.
Warming Drawer Use & Care
Service Information
7
wolfappliance.com
Cleaning and Care Recommendations
IMPORTANT NOTE: Make sure the warming drawer is off
and all surfaces are cool before cleaning any part of the
unit.
DRAWER RACK
Clean the chrome rack with a mild detergent and water.
After cleaning, rinse with clean water and dry thoroughly
with a clean cloth.
Troubleshooting
Service Information
If your Wolf warming drawer is not operating properly, use
the following troubleshooting guide before calling your
Wolf dealer. This guide will save you time and trouble and
may help you avoid the expense of a service call.
When requesting information, literature, replacement parts
or service, always refer to the model and serial number of
your Wolf warming drawer. This information is found on
the product rating plate located on the left front floor area
of the inner cabinet. To access the rating plate, the drawer
must be fully open. For location of the rating plate, refer to
the illustration on page 4. Record the rating plate information below for future reference.
STAINLESS STEEL
Although stainless steel is resistant to most stains, it is not
totally impervious to damage. Salt and some cooking
liquids may pit and stain the surface. Always remove these
spills immediately.
Use a spray degreaser to remove fingerprints and greasy
spatters. Spray on a cloth and wipe surface. Buff dry
immediately to avoid streaking.
For hard water stains, use white vinegar and water.
Do not use abrasive cleaners; they will permanently
scratch the surface. Do not use steel wool pads.
CONTROL PANEL
Be careful not to soak the control panel. Although the
panel is sealed, excessive moisture may cause damage to
the controls.
Use a glass cleaner to remove fingerprints and spills from
the surface of the control panel. Spray first on a cloth
before wiping the panel.
Warming drawer does not operate.
• A fuse may be blown or the circuit breaker tripped.
Replace the fuse or reset the circuit breaker.
• Verify that the warming drawer is plugged in.
Model Number:
Serial Number:
Drawer does not slide smoothly.
• Ball bearings are out of alignment. Fully extend the
drawer and close completely to realign.
Installation Date:
Wolf Dealer:
Phone:
• Drawer is overloaded or the load is unbalanced.
Reduce weight to less than 34 kg or redistribute
contents.
STAINLESS STEEL DRAWER FRONT
There is excessive condensation.
To clean the exterior of the classic stainless steel drawer
front, use a soft, nonabrasive stainless steel cleaner and
apply with a soft lint-free cloth.
To bring out the natural luster of the stainless finish, lightly
wipe the surface with a water-dampened microfiber cloth,
followed with a dry microfiber cloth. All work should follow
the grain direction of the finish. Better results are obtained
by keeping the cloth in continuous contact with the metal.
IMPORTANT NOTE: Under no circumstances should you
use a metallic or highly abrasive cleaner or cloth.
• Remove liquid in the warming drawer pan.
• Cover food with a lid or aluminum foil.
• Temperature setting is too high, use a lower setting.
No heat in the proof setting.
• Room temperature may prevent the thermostat from
turning on. Verify that PROOF is illuminated in the LCD
display on the control panel.
Food dries out in the proof setting.
• Cover food with a lid or aluminum foil.
The information and images in this guide are the copyright property of Wolf Appliance, Inc. Neither this guide nor any information or images contained
herein may be copied or used in whole or in part without the express written permission of Wolf Appliance, Inc. ©Wolf Appliance, Inc. all rights reserved.
WOLF APPLIANCE, INC.
P O BOX 44848
MADISON, WI 53744 USA
WOLFAPPLIANCE.COM
8 1 3 9 6 7 R E V- A
5 / 2009