SCSI Hard Drive Configuration Charts

SCSI Hard Drive Configuration Charts
SCSI DEFINITIONS
PARK. The jumper option park applies when the jumper is present but
not shorting the pins together. In other words, it is positioned off to one
side of the pins.
KEY. The jumper option key applies when the pins on the hard drive are
clipped off and no jumper can be placed in the position.
B-6
Volume Two
SCSI Hard Drive Configuration Charts
18.2 GB
Drive Size:
BC01821938
Model:
Pin 1
J6
Bit 0
Bit 2
J6
Printed
Circuit
Board
Bit 1
Pin 1
J2
F
S
P
W
J2
Pin 1
Pin 1
SCSI ID Settings
SCSI ID Cable
SCSI ID
Bit 2
Bit 1
Bit 0
0
1
POWER
2
SCSI
3
4
5
6
NOTES:
1. All jumper and switch
settings are shown in
the factory default setting,
including those not labeled.
2. Termination default is
disabled/removed.
Key
Jumper NOT Installed
Jumper Installed
Default Settings
Signal Description
S
Start Unit Command Enabled
P
Parity Enabled
W
Write Protect Disabled
F
Force Single-Ended Mode
Key
Jumper
Jumper NOT Installed
Jumper Installed
Volume Two
B-7
SCSI Hard Drive Configuration Charts
18.2 GB
Drive Size:
Model: BB01821AC3
Pin 1
Bit 0
J6
Bit 2
J6
Printed
Circuit
Board
Pin 1
Bit 1
J2
F
S
P
W
J2
Pin 1
Pin 1
SCSI ID Settings
SCSI ID Cable
SCSI ID
Bit 2
Bit 1
Bit 0
0
1
2
POWER
SCSI
3
4
5
6
Key
NOTES:
1. All jumper and switch
settings are shown in
the factory default setting,
including those not labeled.
2. Termination default is
disabled/removed.
Jumper NOT Installed
Jumper Installed
Default Settings
Signal Description
Jumper
S
Start Unit Command Enabled
P
Parity Enabled
W
Write Protect Disabled
F
Force Single-Ended Mode
Key
Jumper NOT Installed
Jumper Installed
B-8
Volume Two
SCSI Hard Drive Configuration Charts
18.2 GB
CN2
BB018222B8
Model:
CN2
CN2
Bit 0
Pin 1
Bit 2
Drive Size:
Bit 1
Pin 1
Printed
Circuit
Board
SCSI ID Settings
SCSI ID Cable
SCSI ID
Bit 2
Bit 1
Bit 0
0
1
POWER
2
SCSI
3
4
5
6
Key
NOTES:
1. All jumper and switch
settings are shown in
the factory default setting,
including those not labeled.
2. Termination default is
disabled/removed.
Jumper NOT Installed
Jumper Installed
Default Settings
Signal Description
S
Start Unit Command Enabled
P
Parity Enabled
W
Write Protect Disabled
F
Force Single-Ended Mode
Key
Jumper
Jumper NOT Installed
Jumper Installed
Volume Two
B-9
SCSI Hard Drive Configuration Charts
Model:
BD018222C1
Bit 2
Pin 1
J6
J6
Bit 0
18.2 GB
Drive Size:
Pin 1
Bit 1
Printed
Circuit
Board
J2
F
S
P
IMPORTANT:
This drive is intended for
non-pluggable applications only.
Migration to a Pluggable Drive Tray
is not supported.
W
J2
Pin 1
Pin 1
SCSI ID Settings
SCSI ID Cable
SCSI ID
Bit 2
Bit 1
Bit 0
0
1
POWER
SCSI
2
3
4
5
6
NOTES:
1. All jumper and switch
settings are shown in
the factory default setting,
including those not labeled.
2. Termination default is
disabled/removed.
Key
Jumper NOT Installed
Jumper Installed
Default Settings
Signal Description
Jumper
S
Start Unit Command Enabled
P
Parity Enabled
W
Write Protect Disabled
F
Force Single-Ended Mode
Disabled
Key
Jumper NOT Installed
Jumper Installed
B-10
Volume Two
SCSI Hard Drive Configuration Charts
18.2 GB
Model: BD018222CA
CN2
Bit 0
Pin 1
CN2
Bit 2
Drive Size:
CN2
Bit 1
Pin 1
Printed
Circuit
Board
SCSI ID Settings
SCSI ID
SCSI ID Cable
Bit 2
Bit 1
Bit 0
0
1
2
POWER
SCSI
3
4
5
6
NOTES:
1. All jumper and switch
settings are shown in
the factory default setting,
including those not labeled.
2. Termination default is
disabled/removed.
Key
Jumper NOT Installed
Jumper Installed
Default Settings
Signal Description
S
Start Unit Command Enabled
P
Parity Enabled
W
Write Protect Disabled
F
Force Single-Ended Mode
Key
Jumper
Jumper NOT Installed
Jumper Installed
Volume Two
B-11
SCSI Hard Drive Configuration Charts
18.2 GB
Drive Size:
HC01841729
Model:
Pin 1
J6
Bit 0
Bit 2
J6
Pin 1
Bit 1
Printed
Circuit
Board
J2
F
S
P
W
J2
Pin 1
Pin 1
SCSI ID Settings
SCSI ID Cable
SCSI ID
Bit 2
Bit 1
Bit 0
0
1
POWER
2
SCSI
3
4
5
6
NOTES:
1. All jumper and switch
settings are shown in
the factory default setting,
including those not labeled.
2. Termination default is
disabled/removed.
Key
Jumper NOT Installed
Jumper Installed
Default Settings
Signal Description
Jumper
S
Start Unit Command Enabled
P
Parity Enabled
W
Write Protect Disabled
F
Force Single-Ended Mode
Key
Jumper NOT Installed
Jumper Installed
B-12
Volume Two
SCSI Hard Drive Configuration Charts
9.1 GB
Drive Size:
3391NS
Model:
J2
Bit 1
Pin 1
S W
Bit 0
Bit 2
Pin 1
X
J2
Printed
Circuit
Board
Key
For Hot-Pluggable Drive Tray, connect
SCSI ID Cable to this Connector
Pin 1
POWER
SCSI
SCSI ID Settings
SCSI ID
Bit 2
Bit 1
Bit 0
0
1
2
NOTES:
1. All jumper and switch
settings are shown in
the factory default setting,
including those not labeled.
2. Termination default is
disabled/removed.
3
4
5
6
Default Settings
Signal Description
S
Key
Volume Two
Jumper NOT Installed
Jumper
Start Unit Command Enabled
Parity Enabled**
Jumper Installed
W
Write Protect Disabled
** Not Configurable
X
Synch Data Transfer Enabled**
n/a
B-13
SCSI Hard Drive Configuration Charts
9.1 GB
Drive Size:
3391WS
Model:
Bit 1
J2
S W
Bit 0
Bit 2
Pin 1
J2
Pin 1
Key
X
Bit 3
Bit 1
Printed
Circuit
Board
Bit 2
Bit 0
Pin 1
Pin 1
J1B
SCSI
J1B
POWER
For Hot-Pluggable Drive Tray, connect
SCSI ID Cable to this Connector
SCSI ID Settings
SCSI ID
Bit 2
Bit 1
Bit 0
0
1
2
NOTES:
1. All jumper and switch
settings are shown in
the factory default setting,
including those not labeled.
2. Termination default is
disabled/removed.
3
4
5
6
Default Settings
Signal Description
S
Key
B-14
Jumper NOT Installed
Jumper
Start Unit Command Enabled
Parity Enabled**
Jumper Installed
W
Write Protect Disabled
** Not Configurable
X
Synch Data Transfer Enabled**
n/a
Volume Two
9.1 GB
Drive Size:
BB00921791
Model:
Pin 1
Bit 0
J6
Bit 2
J6
Pin 1
Bit 1
Printed
Circuit
Board
J2
F
S
P
W
J2
Pin 1
Pin 1
SCSI ID Settings
SCSI ID Cable
SCSI ID
Bit 2
Bit 1
Bit 0
0
1
POWER
2
SCSI
3
4
5
6
NOTES:
1. All jumper and switch
settings are shown in
the factory default setting,
including those not labeled.
2. Termination default is
disabled/removed.
Key
Jumper NOT Installed
Jumper Installed
Default Settings
Signal Description
S
Start Unit Command Enabled
P
Parity Enabled
W
Write Protect Disabled
F
Force Single-Ended Mode
Key
Jumper
Jumper NOT Installed
Jumper Installed
Volume Two
B-15
SCSI Hard Drive Configuration Charts
9.1 GB
Drive Size:
Model:
BB00921B91
Pin 1
Bit 0
J6
Bit 2
J6
Pin 1
Bit 1
Printed
Circuit
Board
J2
F
S
P
W
J2
Pin 1
Pin 1
SCSI ID Settings
SCSI ID Cable
SCSI ID
Bit 2
Bit 1
Bit 0
0
1
POWER
2
SCSI
3
4
5
6
Key
NOTES:
1. All jumper and switch
settings are shown in
the factory default setting,
including those not labeled.
2. Termination default is
disabled/removed.
Jumper NOT Installed
Jumper Installed
Default Settings
Signal Description
Jumper
S
Start Unit Command Enabled
P
Parity Enabled
W
Write Protect Disabled
F
Force Single-Ended Mode
Key
Jumper NOT Installed
Jumper Installed
B-16
Volume Two
SCSI Hard Drive Configuration Charts
9.1 GB
Model:
BB009222B5
CN2
CN2
Bit 0
Pin 1
CN2
Bit 2
Drive Size:
Pin 1
Bit 1
Printed
Circuit
Board
SCSI ID Settings
SCSI ID Cable
SCSI ID
Bit 2
Bit 1
Bit 0
0
1
POWER
2
SCSI
3
4
5
6
NOTES:
1. All jumper and switch
settings are shown in
the factory default setting,
including those not labeled.
2. Termination default is
disabled/removed.
Key
Jumper NOT Installed
Jumper Installed
Default Settings
Signal Description
S
Start Unit Command Enabled
P
Parity Enabled
W
Write Protect Disabled
F
Force Single-Ended Mode
Key
Jumper
Jumper NOT Installed
Jumper Installed
Volume Two
B-17
SCSI Hard Drive Configuration Charts
9.1 GB
Drive Size:
BD00921937
Model:
Pin 1
Bit 0
J6
Bit 2
J6
Pin 1
Bit 1
Printed
Circuit
Board
J2
F
S
P
W
J2
Pin 1
Pin 1
SCSI ID Settings
SCSI ID
SCSI ID Cable
Bit 2
Bit 1
Bit 0
0
1
2
POWER
SCSI
3
4
5
6
NOTES:
1. All jumper and switch
settings are shown in
the factory default setting,
including those not labeled.
2. Termination default is
disabled/removed.
Key
Jumper NOT Installed
Jumper Installed
Default Settings
Signal Description
Jumper
S
Start Unit Command Enabled
P
Parity Enabled
W
Write Protect Disabled
F
Force Single-Ended Mode
Key
Jumper NOT Installed
Jumper Installed
B-18
Volume Two
SCSI Hard Drive Configuration Charts
9.1 GB
Drive Size:
Model: BD009222BB
Pin 1
Bit 0
J6
Bit 2
J6
Pin 1
Bit 1
Printed
Circuit
Board
J2
F
S
P
W
J2
Pin 1
Pin 1
SCSI ID Settings
SCSI ID Cable
SCSI ID
Bit 2
Bit 1
Bit 0
0
1
POWER
2
SCSI
3
4
5
6
Key
NOTES:
1. All jumper and switch
settings are shown in
the factory default setting,
including those not labeled.
2. Termination default is
disabled/removed.
Jumper NOT Installed
Jumper Installed
Default Settings
Signal Description
S
Start Unit Command Enabled
P
Parity Enabled
W
Write Protect Disabled
F
Force Single-Ended Mode
Jumper
Disabled
Key
Jumper NOT Installed
Jumper Installed
Volume Two
B-19
SCSI Hard Drive Configuration Charts
9.1 GB
Model:
BD009222C7
CN2
CN2
Bit 0
Pin 1
CN2
Bit 2
Drive Size:
Bit 1
Pin 1
Printed
Circuit
Board
SCSI ID Settings
SCSI Cable
SCSI ID
Bit 2
Bit 1
Bit 0
0
1
POWER
2
SCSI
3
4
5
6
NOTES:
1. All jumper and switch
settings are shown in
the factory default setting,
including those not labeled.
2. Termination default is
disabled/removed.
Key
Jumper NOT Installed
Jumper Installed
Default Settings
Signal Description
Jumper
S
Start Unit Command Enabled
P
Parity Enabled
W
Write Protect Disabled
F
Force Single-Ended Mode
Key
Jumper NOT Installed
Jumper Installed
B-20
Volume Two
SCSI Hard Drive Configuration Charts
9.1 GB
Drive Size:
DCHS09U
Model:
Pin 1
S
J8
J8
P
Pin 1
X
W
Bit 1
Printed
Circuit
Board
J5
J5
Pin 1
SCSI
Bit 2
Bit 0
Pin 1
POWER
For Hot-Pluggable Drive Tray, connect
SCSI ID Cable to this Connector.
SCSI ID Settings
SCSI ID
Bit 2
Bit 1
Bit 0
0
1
2
NOTES:
1. All jumper and switch
settings are shown in
the factory default setting,
including those not labeled.
2. Termination default is
disabled/removed.
3
4
5
6
Default Settings
Signal Description
Key
Volume Two
S
Autostart Enable
Jumper NOT Installed
P
Parity Disable
Jumper Installed
W
Write Protect Enable
X
Synch Data Transfer Disable
Jumper
B-21
SCSI Hard Drive Configuration Charts
9.1 GB
Drive Size:
DCHS09Z
Model:
Bit 2
Bit 0*
Pin 3
J8
Pins 1 & 2
do not exist.
S
P
J8
Bit 1
Pin 3
W
Printed
Circuit
Board
X
*For Hot-Pluggable Drive Tray,
connect Odd Color Wire on 6-Pin
SCSI ID Connector to Bit 0 Pair.
POWER
SCSI
Pin 1
SCSI ID Settings
SCSI ID
Bit 2
Bit 1
Bit 0
0
1
2
NOTES:
1. All jumper and switch
settings are shown in
the factory default setting,
including those not labeled.
2. Termination default is
disabled/removed.
3
4
5
6
Default Settings
Signal Description
Key
B-22
S
Autostart Enable
Jumper NOT Installed
P
Parity Disable
Jumper Installed
W
Write Protect Enable
X
Synch Data Transfer Disable
Jumper
Volume Two
SCSI Hard Drive Configuration Charts
P
Bit 3
J2
S
DDRS-39130
Model:
Bit 1
9.1 GB
Drive Size:
Bit 2
Printed
Circuit
Board
Pin 1
J2
IMPORTANT:
This drive is intended for
non-pluggable applications only.
Migration to a Pluggable Drive Tray
is not supported.
J2
SCSI ID Cable
Bit 0
Pin 1
SCSI ID Settings
SCSI
SCSI ID
Bit 2
Bit 1
Bit 0
0
1
POWER
2
3
4
5
6
NOTES:
1. All jumper and switch
settings are shown in
the factory default setting,
including those not labeled.
2. Termination default is
disabled/removed.
Key
Jumper NOT Installed
Jumper Installed
Default Settings
Signal Description
Jumper
S
Start Unit Command Enabled
P
Parity Enabled
W
Write Protect Disabled
n/a
X
Synch Data Transfer Enabled
n/a
Key
Jumper NOT Installed
Jumper Installed
Volume Two
B-23
SCSI Hard Drive Configuration Charts
9.1 GB
Drive Size:
Model:
HD0094172B
Pin 1
Bit 0
J6
Bit 2
J6
Pin 1
Bit 1
Printed
Circuit
Board
J2
F
S
P
W
J2
Pin 1
Pin 1
SCSI ID Settings
SCSI ID Cable
SCSI ID
Bit 2
Bit 1
Bit 0
0
1
POWER
2
SCSI
3
4
5
6
NOTES:
1. All jumper and switch
settings are shown in
the factory default setting,
including those not labeled.
2. Termination default is
disabled/removed.
Key
Jumper NOT Installed
Jumper Installed
Default Settings
Signal Description
Jumper
S
Start Unit Command Enabled
P
Parity Enabled
W
Write Protect Disabled
F
Force Single-Ended Mode
Key
Jumper NOT Installed
Jumper Installed
B-24
Volume Two
SCSI Hard Drive Configuration Charts
MAB3091SP
Model:
W
CN7
Bit 2
Bit 1
Bit 0
9.1GB
Drive Size:
Pin 1
Printed
Circuit
Board
CN7
IMPORTANT:
This drive is intended for
non-pluggable applications only.
Migration to a Pluggable Drive Tray
is not supported.
S
P
CN6
CN6
Pin 1
POWER
Pin 1
SCSI ID Settings
CN1
SCSI
SCSI ID
Bit 2
Bit 1
Bit 0
0
1
2
Pin 1
3
4
5
6
NOTES:
1. All jumper and switch
settings are shown in
the factory default setting,
including those not labeled.
2. Termination default is
disabled/removed.
Default Settings
Signal Description
S
Start Unit Command Enabled
P
Parity Enabled
W
Write Protect Disabled
Jumper
Synch Data Transfer Enabled
n/a
CN6 Default Settings
Pins Description
Key
Jumper NOT Installed
1-2 SCSI Termination Resistor
Jumper Installed
3-4 Start Unit Command Enabled
Jumper
5-6 Setting Terminator Power Supplied
Volume Two
B-25
SCSI Hard Drive Configuration Charts
9.1 GB
ST19101W
Model:
J6
Bit 2
Bit 1
Bit 0
Drive Size:
Pin 1
J6
Printed
Circuit
Board
Pin 1
J2
J1A
J2
S
P
W
Pin 1
Pin 1
J1A
SCSI
Bit 2
Bit 1
Bit 0
POWER
Pin 1
For Hot-Pluggable Drive Tray, connect
SCSI ID Cable to this Connector
SCSI ID Settings
SCSI ID
Bit 2
Bit 1
Bit 0
0
1
2
NOTES:
1. All jumper and switch
settings are shown in
the factory default setting,
including those not labeled.
2. Termination default is
disabled/removed.
3
4
5
6
Default Settings
Signal Description
Key
S
Start Unit Command Enabled
Jumper NOT Installed
P
Parity Enabled
Jumper Installed
W
Write Protect Disabled
** Not Configurable
B-26
Synch Data Transfer Enabled
Jumper
n/a
Volume Two
SCSI Hard Drive Configuration Charts
9.1 GB
ST19171N
Model:
J6
Bit 2
Bit 1
Bit 0
Drive Size:
Pin 1
J6
Pin 1
Printed
Circuit
Board
J2
Pin 1
J2
W
S
P
POWER
SCSI
Pin 1
Pin 1
For Hot-Pluggable Drive Tray, connect
SCSI ID Cable to this Connector
SCSI ID Settings
SCSI ID
Bit 2
Bit 1
Bit 0
0
1
2
NOTES:
1. All jumper and switch
settings are shown in
the factory default setting,
including those not labeled.
2. Termination default is
disabled/removed.
3
4
5
6
Default Settings
Signal Description
Key
S
Start Unit Command Enabled
Jumper NOT Installed
P
Parity Enabled
Jumper Installed
W
Write Protect Disabled
Synch Data Transfer Enabled
Volume Two
Jumper
n/a
B-27
9.1 GB
ST19171W
Model:
Bit 2
Bit 1
Bit 0
Drive Size:
Pin 1
Bit 2
Bit 1
Bit 0
J6
J1A
Pin 1
For Pluggable Drive Tray, connect
SCSI ID Cable to this Connector.
J6
Pin 1
SCSI ID Settings
Printed
Circuit
Board
SCSI ID
Bit 2
Bit 1
Bit 0
0
1
J2
W
2
J2
S
P
3
4
Pin 1
5
6
POWER
J1A
SCSI
Key
Jumper NOT Installed
Jumper Installed
Default Settings
Pin 1
Signal Description
NOTES:
1. All jumper and switch
settings are shown in
the factory default setting,
including those not labeled.
2. Termination default is
disabled/removed.
B-28
Jumper
S
Start Unit Command Enabled
P
Parity Enabled
W
Write Protect Disabled
Synch Data Transfer Enabled
Key
n/a
Jumper NOT Installed
Jumper Installed
Volume Two
SCSI Hard Drive Configuration Charts
9.1 GB
Drive Size:
ST19171WS
Model:
Bit 2
Bit 1
Bit 0
J6
J6
Pin 1
Printed
Circuit
Board
Pin 1
J2
W
J1A
J2
S
P
Pin 1
Pin 1
J1A
SCSI
Bit 2
Bit 1
Bit 0
POWER
Pin 1
For Hot-Pluggable Drive Tray, connect
SCSI ID Cable to this Connector
SCSI ID Settings
SCSI ID
Bit 2
Bit 1
Bit 0
0
1
2
NOTES:
1. All jumper and switch
settings are shown in
the factory default setting,
including those not labeled.
2. Termination default is
disabled/removed.
3
4
5
6
Default Settings
Signal Description
Key
S
Start Unit Command Enabled
Jumper NOT Installed
P
Parity Enabled
Jumper Installed
W
Write Protect Disabled
Synch Data Transfer Enabled
B-28
Jumper
n/a
Volume Two
SCSI Hard Drive Configuration Charts
4.3 GB
Drive Size:
4345NS
Model:
J2
Bit 1
Pin 1
S W
Bit 0
Bit 2
Pin 1
X
J2
Printed
Circuit
Board
Key
For Hot-Pluggable Drive Tray, connect
SCSI ID Cable to this Connector
Pin 1
POWER
SCSI
SCSI ID Settings
SCSI ID
Bit 2
Bit 1
Bit 0
0
1
2
NOTES:
1. All jumper and switch
settings are shown in
the factory default setting,
including those not labeled.
2. Termination default is
disabled/removed.
3
4
5
6
Default Settings
Signal Description
S
Key
Volume Two
Jumper NOT Installed
Jumper
Start Unit Command Enabled
Parity Enabled**
Jumper Installed
W
Write Protect Disabled
** Not Configurable
X
Synch Data Transfer Enabled**
n/a
B-29
SCSI Hard Drive Configuration Charts
4.3 GB
Drive Size:
4345WS
Model:
Bit 1
J2
Pin 1
S W
J2
Bit 0
Bit 2
Pin 1
Key
X
Bit 3
Bit 1
Printed
Circuit
Board
Pin 1
Bit 2
Bit 0
SCSI
J1B
Pin 1
J1B
POWER
For Hot-Pluggable Drive Tray, connect
SCSI ID Cable to this Connector
SCSI ID Settings
SCSI ID
Bit 2
Bit 1
Bit 0
0
1
2
NOTES:
1. All jumper and switch
settings are shown in
the factory default setting,
including those not labeled.
2. Termination default is
disabled/removed.
3
4
5
6
Default Settings
Signal Description
S
Key
B-30
Jumper NOT Installed
Jumper
Start Unit Command Enabled
Parity Enabled**
Jumper Installed
W
Write Protect Disabled
** Not Configurable
X
Synch Data Transfer Enabled**
n/a
Volume Two
SCSI Hard Drive Configuration Charts
4.3 GB
Drive Size:
BB00421793
Model:
Pin 1
Bit 0
J6
Bit 2
J6
Pin 1
Bit 1
Printed
Circuit
Board
J2
F
S
P
W
J2
Pin 1
Pin 1
SCSI ID Settings
SCSI ID Cable
SCSI ID
Bit 2
Bit 1
Bit 0
0
1
POWER
2
SCSI
3
4
5
6
NOTES:
1. All jumper and switch
settings are shown in
the factory default setting,
including those not labeled.
2. Termination default is
disabled/removed.
Key
Jumper NOT Installed
Jumper Installed
Default Settings
Signal Description
S
Start Unit Command Enabled
P
Parity Enabled
W
Write Protect Disabled
F
Force Single-Ended Mode
Key
Jumper
Jumper NOT Installed
Jumper Installed
Volume Two
B-31
SCSI Hard Drive Configuration Charts
4.3 GB
Drive Size:
BD00421936
Model:
Pin 1
Bit 0
J6
Bit 2
J6
Pin 1
Bit 1
Printed
Circuit
Board
J2
F
S
P
W
J2
Pin 1
Pin 1
SCSI ID Settings
SCSI ID Cable
SCSI ID
Bit 2
Bit 1
Bit 0
0
1
POWER
2
SCSI
3
4
5
6
NOTES:
1. All jumper and switch
settings are shown in
the factory default setting,
including those not labeled.
2. Termination default is
disabled/removed.
Key
Jumper NOT Installed
Jumper Installed
Default Settings
Signal Description
Jumper
S
Start Unit Command Enabled
P
Parity Enabled
W
Write Protect Disabled
F
Force Single-Ended Mode
Key
Jumper NOT Installed
Jumper Installed
B-32
Volume Two
SCSI Hard Drive Configuration Charts
4.3 GB
Drive Size:
DCHS04U
Model:
Pin 1
S
J8
J8
P
Pin 1
X
W
Bit 1
Printed
Circuit
Board
J5
J5
Pin 1
SCSI
Bit 2
Bit 0
Pin 1
POWER
For Hot-Pluggable Drive Tray, connect
SCSI ID Cable to this Connector.
SCSI ID Settings
SCSI ID
Bit 2
Bit 1
Bit 0
0
1
2
NOTES:
1. All jumper and switch
settings are shown in
the factory default setting,
including those not labeled.
2. Termination default is
disabled/removed.
3
4
5
6
Default Settings
Signal Description
Key
Volume Two
S
Autostart Enable
Jumper NOT Installed
P
Parity Disable
Jumper Installed
W
Write Protect Enable
X
Synch Data Transfer Disable
Jumper
B-33
SCSI Hard Drive Configuration Charts
4.3 GB
Drive Size:
Pin 3
Bit 2
Bit 0*
DCHS04Z
Model:
J8
Pins 1 & 2
do not exist.
S J8
P
Bit 1
Pin 3
W
Printed
Circuit
Board
X
*For Hot-Pluggable Drive Tray,
connect Odd Color Wire on 6-Pin
SCSI ID Connector to Bit 0 Pair.
POWER
SCSI
Pin 1
SCSI ID Settings
SCSI ID
Bit 2
Bit 1
Bit 0
0
1
2
NOTES:
1. All jumper and switch
settings are shown in
the factory default setting,
including those not labeled.
2. Termination default is
disabled/removed.
3
4
5
6
Default Settings
Signal Description
Key
B-34
S
Autostart Enable
Jumper NOT Installed
P
Parity Disable
Jumper Installed
W
Write Protect Enable
X
Synch Data Transfer Disable
Jumper
Volume Two
SCSI Hard Drive Configuration Charts
4.3 GB
Drive Size:
DDRS-34560
Model:
P
Pin 1
S
Bit 1
Bit 3
J2
Bit 0
Bit 2
Printed
Circuit
Board
Pin 1
J2
J2
IMPORTANT:
This drive is intended for
non-pluggable applications only.
Migration to a Pluggable Drive Tray
is not supported.
Pin 1
SCSI
J1B
POWER
SCSI ID Settings
SCSI ID
NOTES:
1. All jumper and switch
settings are shown in
the factory default setting,
including those not labeled.
2. Termination default is
disabled/removed.
Bit 2
Bit 1
Bit 0
0
1
2
3
4
5
6
Default Settings
Signal Description
Key
Jumper
S
Start Unit Command Enabled
Jumper NOT Installed
P
Parity Enabled
Jumper Installed
W
Write Protect Disabled-
n/a
X
Synch Data Transfer Enabled
n/a
Volume Two
B-35
SCSI Hard Drive Configuration Charts
4.3 GB
DFHSS4F
Model:
Bit 2
Bit 0*
Drive Size:
J8
Pin 3
Pins 1 & 2
do not exist.
S
Bit 1
Printed
Circuit
Board
P
J8
Pin 3
W
X
*For Pluggable Drive Tray, connect
Odd Color Wire on 6-Pin SCSI ID
Connector to Bit 0 Pair.
SCSI ID Settings
SCSI ID
POWER
Bit 2
Bit 1
Bit 0
0
SCSI
1
2
3
Pin 1
4
5
6
NOTES:
1. All jumper and switch
settings are shown in
the factory default setting,
including those not labeled.
2. Termination default is
disabled/removed.
Key
Jumper NOT Installed
Jumper Installed
Default Settings
Signal Description
Jumper
S
Start Unit Command Enabled
P
Parity Enabled
W
Write Protect Disabled
X
Synch Data Transfer Enabled
Key
Jumper NOT Installed
Jumper Installed
B-36
Volume Two
SCSI Hard Drive Configuration Charts
4.3 GB
DFHSS4W
Model:
Bit 1
Drive Size:
S
J8
Pin 1
J5
P
X
W
Bit 2
Bit 0
Pin 1
Pin 1
For Pluggable Drive Tray, connect
SCSI ID Cable to this Connector.
J8
SCSI ID Settings
SCSI ID
Bit 2
Bit 1
Bit 0
0
Printed
Circuit
Board
1
2
3
4
5
6
J5
Pin 1
SCSI
Key
Jumper NOT Installed
Jumper Installed
Default Settings
POWER
NOTES:
1. All jumper and switch
settings are shown in
the factory default setting,
including those not labeled.
2. Termination default is
disabled/removed.
Volume Two
Signal Description
S
Start Unit Command Enabled
P
Parity Enabled
W
Write Protect Disabled
X
Synch Data Transfer Enabled
Key
Jumper
Jumper NOT Installed
Jumper Installed
B-37
SCSI Hard Drive Configuration Charts
4.3 GB
Drive Size:
HD00441730
Model:
Pin 1
Bit 0
J6
Bit 2
J6
Pin 1
Bit 1
Printed
Circuit
Board
J2
F
S
P
W
J2
Pin 1
Pin 1
SCSI ID Settings
SCSI ID Cable
SCSI ID
Bit 2
Bit 1
Bit 0
0
1
POWER
2
SCSI
3
4
5
6
NOTES:
1. All jumper and switch
settings are shown in
the factory default setting,
including those not labeled.
2. Termination default is
disabled/removed.
Key
Jumper NOT Installed
Jumper Installed
Default Settings
Signal Description
Jumper
S
Start Unit Command Enabled
P
Parity Enabled
W
Write Protect Disabled
F
Force Single-Ended Mode
Key
Jumper NOT Installed
Jumper Installed
B-38
Volume Two
SCSI Hard Drive Configuration Charts
MAB3045SP
Model:
W
CN7
Bit 2
Bit 1
Bit 0
4.3 GB
Drive Size:
Pin 1
Printed
Circuit
Board
CN7
IMPORTANT:
This drive is intended for
non-pluggable applications only.
Migration to a Pluggable Drive Tray
is not supported.
S
P
CN6
CN6
Pin 1
POWER
Pin 1
SCSI ID Settings
CN1
SCSI
SCSI ID
Bit 2
Bit 1
Bit 0
0
1
2
Pin 1
3
4
5
6
NOTES:
1. All jumper and switch
settings are shown in
the factory default setting,
including those not labeled.
2. Termination default is
disabled/removed.
Default Settings
Signal Description
S
Start Unit Command Enabled
P
Parity Enabled
W
Write Protect Disabled
Jumper
Synch Data Transfer Enabled
n/a
CN6 Default Settings
Pins Description
Key
Jumper NOT Installed
1-2 SCSI Termination Resistor
Jumper Installed
3-4 Start Unit Command Enabled
Jumper
5-6 Setting Terminator Power Supplied
Volume Two
B-39
SCSI Hard Drive Configuration Charts
4.3 GB
Drive Size:
ST15150N
Model:
J1
Pin 1
X
W
J4
S
P
Bit 0*
Bit 2
Bit 1
Printed
Circuit
Board
Pin 1
*For Pluggable Drive Tray, connect
Odd Color Wire on 6-Pin SCSI ID
Connector to Bit 0 Pair.
J1 Pin 1
SCSI ID Settings
SCSI ID
J4
Bit 2
Bit 1
Bit 0
0
1
2
SCSI
3
POWER
4
5
6
NOTES:
1. All jumper and switch
settings are shown in
the factory default setting,
including those not labeled.
2. Termination default is
disabled/removed.
Key
Jumper NOT Installed
Jumper Installed
Default Settings
Signal Description
Jumper
S
Start Unit Command Enabled
P
Parity Enabled
W
Write Protect Disabled
X
Synch Data Transfer Enabled
Key
Jumper NOT Installed
Jumper Installed
B-40
Volume Two
SCSI Hard Drive Configuration Charts
4.3 GB
Drive Size:
Pin 1
Pin 1
W
ST15150W
Model:
J1
J5
J4
S
Pin 1
P
Bit 2
Bit 1
Bit 0
X
For Pluggable Drive Tray, connect
SCSI ID Cable to this Connector.
SCSI ID Settings
SCSI ID
Printed
Circuit
Board
Bit 2
Bit 1
Bit 0
0
1
2
3
4
5
Pin 1
6
J1
Pin 1
J4
Key
Jumper NOT Installed
Jumper Installed
Default Settings
Signal Description
SCSI
J5
POWER
NOTES:
1. All jumper and switch
settings are shown in
the factory default setting,
including those not labeled.
2. Termination default is
disabled/removed.
Volume Two
S
Start Unit Command Enabled
P
Parity Enabled
W
Write Protect Disabled
X
Synch Data Transfer Enabled
Key
Jumper
Jumper NOT Installed
Jumper Installed
B-41
SCSI Hard Drive Configuration Charts
4.3 GB
ST34371N
Model:
J6
Bit 2
Bit 1
Bit 0
Drive Size:
Pin 1
J6
Pin 1
Printed
Circuit
Board
J2
Pin 1
J2
W
S
POWER
P
SCSI
Pin 1
Pin 1
For Hot-Pluggable Drive Tray, connect
SCSI ID Cable to this Connector
SCSI ID Settings
SCSI ID
Bit 2
Bit 1
Bit 0
0
1
2
NOTES:
1. All jumper and switch
settings are shown in
the factory default setting,
including those not labeled.
2. Termination default is
disabled/removed.
3
4
5
6
Default Settings
Signal Description
Key
S
Start Unit Command Enabled
Jumper NOT Installed
P
Parity Enabled
Jumper Installed
W
Write Protect Disabled
Synch Data Transfer Enabled
B-42
Jumper
n/a
Volume Two
SCSI Hard Drive Configuration Charts
4.3 GB
Drive Size:
ST34371W
Model:
Bit 2
Bit 1
Bit 0
J6
J6
Pin 1
Printed
Circuit
Board
Pin 1
J2
W
J1A
J2
S
P
Pin 1
Pin 1
J1A
SCSI
Bit 2
Bit 1
Bit 0
POWER
Pin 1
For Hot-Pluggable Drive Tray, connect
SCSI ID Cable to this Connector
SCSI ID Settings
SCSI ID
Bit 2
Bit 1
Bit 0
0
1
2
NOTES:
1. All jumper and switch
settings are shown in
the factory default setting,
including those not labeled.
2. Termination default is
disabled/removed.
3
4
5
6
Default Settings
Signal Description
Key
S
Start Unit Command Enabled
Jumper NOT Installed
P
Parity Enabled
Jumper Installed
W
Write Protect Disabled
Synch Data Transfer Enabled
Volume Two
Jumper
n/a
B-43
SCSI Hard Drive Configuration Charts
4.3 GB
Drive Size:
ST34501W
Model:
J6
J6
Bit 0
Bit 2
Pin 1
Pin 1
Bit 1
Printed
Circuit
Board
J2
Bit 1
S
P
W
J2
J5
Pin 1
Pin 1
J5
Bit 2
Bit 0
Pin 1
Pin 1
For Hot-Pluggable Drive Tray, connect
SCSI ID Cable to this Connector.
POWER
SCSI
SCSI ID Settings
SCSI ID
Bit 2
Bit 1
Bit 0
0
1
2
NOTES:
1. All jumper and switch
settings are shown in
the factory default setting,
including those not labeled.
2. Termination default is
disabled/removed.
3
4
5
6
Default Settings
Signal Description
Key
B-44
S
Start Unit Command Enabled
Jumper NOT Installed
P
Parity Enabled
Jumper Installed
W
Write Protect Disabled
Jumper
Volume Two
SCSI Hard Drive Configuration Charts
4.3 GB
ST34572N
Model:
J6
Bit 2
Bit 1
Bit 0
Drive Size:
J6
Pin 1
Pin 1
Printed
Circuit
Board
J2
J2
W
Pin 1
S
P
POWER
SCSI
Pin 1
Pin 1
For Hot-Pluggable Drive Tray, connect
SCSI ID Cable to this Connector
SCSI ID Settings
SCSI ID
Bit 2
Bit 1
Bit 0
0
1
2
NOTES:
1. All jumper and switch
settings are shown in
the factory default setting,
including those not labeled.
2. Termination default is
disabled/removed.
3
4
5
6
Default Settings
Signal Description
Key
S
Start Unit Command Enabled
Jumper NOT Installed
P
Parity Enabled
Jumper Installed
W
Write Protect Disabled
Synch Data Transfer Enabled
Volume Two
Jumper
n/a
B-45
SCSI Hard Drive Configuration Charts
4.3 GB
ST34572W
Model:
J6
Bit 2
Bit 1
Bit 0
Drive Size:
J6
Pin 1
Printed
Circuit
Board
Pin 1
J2
J1A
J2
S
P
W
Pin 1
Pin 1
POWER
SCSI
Bit 2
Bit 1
Bit 0
J1A
For Hot-Pluggable Drive Tray, connect
SCSI ID Cable to this Connector
Pin 1
SCSI ID Settings
SCSI ID
Bit 2
Bit 1
Bit 0
0
1
2
NOTES:
1. All jumper and switch
settings are shown in
the factory default setting,
including those not labeled.
2. Termination default is
disabled/removed.
3
4
5
6
Default Settings
Signal Description
Key
S
Start Unit Command Enabled
Jumper NOT Installed
P
Parity Enabled
Jumper Installed
W
Write Protect Disabled
Synch Data Transfer Enabled
B-46
Jumper
n/a
Volume Two
SCSI Hard Drive Configuration Charts
4.3 GB
Drive Size:
WDE4360
Model:
X
S
Bit 2
Bit 0
Pin 1
Printed
Circuit
Board
Bit 1
Pin 1
For Hot-Pluggable Drive Tray, connect
SCSI ID Cable to this Connector
Pin 1
POWER
SCSI
SCSI ID Settings
SCSI ID
Bit 2
Bit 1
Bit 0
0
1
2
NOTES:
1. All jumper and switch
settings are shown in
the factory default setting,
including those not labeled.
2. Termination default is
disabled/removed.
3
4
5
6
Default Settings
Signal Description
S
Key
Volume Two
Jumper NOT Installed
Jumper
Start Unit Command Enabled
Parity Enabled**
n/a
Jumper Installed
W
Write Protect Disabled
n/a
** Not Configurable
X
Synch Data Transfer Enabled
B-47
SCSI Hard Drive Configuration Charts
XP34300W
Bit 1
Model:
S
Bit 3
4.3 GB
Drive Size:
J3
Pin 1
W
Bit 2
Bit 0
Pin 1
Pin 1
For Pluggable Drive Tray, connect
SCSI ID Cable to this Connector.
J3
SCSI ID Settings
SCSI ID
Bit 2
Bit 1
Bit 0
0
Printed
Circuit
Board
1
2
3
4
5
6
SCSI
Pin 1
Key
Jumper NOT Installed
Jumper Installed
Default Settings
POWER
Signal Description
S
Jumper
Start Unit Command Enabled
Parity Enabled**
W
NOTES:
1. All jumper and switch
settings are shown in
the factory default setting,
including those not labeled.
2. Termination default is
disabled/removed.
B-48
n/a
Write Protect Disabled
Synch Data Transfer Enabled**
Key
Jumper NOT Installed
n/a
** Not Configurable
Jumper Installed
Volume Two
SCSI Hard Drive Configuration Charts
4.2 GB
CUDA
Model:
J6
Bit 2
Bit 1
Bit 0
Drive Size:
Pin 1
J6
Pin 1
Printed
Circuit
Board
J2
Pin 1
J2
W
S
POWER
P
SCSI
Pin 1
Pin 1
For Hot-Pluggable Drive Tray, connect
SCSI ID Cable to this Connector
SCSI ID Settings
SCSI ID
Bit 2
Bit 1
Bit 0
0
1
2
NOTES:
1. All jumper and switch
settings are shown in
the factory default setting,
including those not labeled.
2. Termination default is
disabled/removed.
3
4
5
6
Default Settings
Signal Description
Key
S
Start Unit Command Enabled
Jumper NOT Installed
P
Parity Enabled
Jumper Installed
W
Write Protect Disabled
Synch Data Transfer Enabled
Volume Two
Jumper
n/a
B-49
SCSI Hard Drive Configuration Charts
Drive Size:
2150 MB
ORION
Model:
IBM Drive
Assembly Number 247266
Position # 6 5 4 3 2 1
1
3
5
7
9 11 13 15 17 19 21 23
2
4
6
8 10 12 14 16 18 20 22 24
Pin #
SCSI ID Settings
SCSI ID
6
5
Position #
3
4
2
1
0
1
2
3
4
5
6
7
Key
Jumper NOT Installed
Jumper Installed
B-50
Volume Two
SCSI Hard Drive Configuration Charts
Drive Size:
2.15 GB
Model:
ST32155N
Seagate Drive
Assembly Number 243019
11 9 7 5
3
1
12 10 8 6
4
2
SCSI ID Settings
SCSI ID
1-2
3-4
5-6
7-8
9-10 11-12
0
1
2
3
4
5
6
7
Key
Jumper NOT Installed
Jumper Installed
Volume Two
B-51
SCSI Hard Drive Configuration Charts
C2490A
Model:
X
S
Bit 0*
2.1 GB
Bit 2
Drive Size:
W
Bit 1
Pin 1
P
Printed
Circuit
Board
*For Pluggable Drive Tray, connect
Odd Wire on 6-Pin SCSI ID Connector
to Bit 0 Pair.
SCSI ID Settings
Pin 1
SCSI ID
POWER
Bit 2
Bit 1
Bit 0
0
SCSI
1
2
3
Pin 1
4
5
6
NOTES:
1. All jumper and switch
settings are shown in
the factory default setting,
including those not labeled.
2. Termination default is
disabled/removed.
Key
Jumper NOT Installed
Jumper Installed
Default Settings
Signal Description
Jumper
S
Start Unit Command Enabled
P
Parity Enabled
W
Write Protect Disabled
X
Synch Data Transfer Enabled
Key
Jumper NOT Installed
Jumper Installed
B-52
Volume Two
SCSI Hard Drive Configuration Charts
2.1 GB
DFHSS2W
Model:
Bit 1
Drive Size:
J5
P
S
Pin 1
X
Bit 2
J8
Bit 0
Pin 1
W
Pin 1
For Pluggable Drive Tray, connect
SCSI ID Cable to this Connector.
J8
SCSI ID Settings
SCSI ID
Bit 2
Bit 1
Bit 0
0
Printed
Circuit
Board
1
2
3
4
5
6
Key
J5
Pin 1
SCSI
Jumper NOT Installed
Jumper Installed
Default Settings
Signal Description
POWER
NOTES:
1. All jumper and switch
settings are shown in
the factory default setting,
including those not labeled.
2. Termination default is
disabled/removed.
Volume Two
S
Start Unit Command Enabled
P
Parity Enabled
W
Write Protect Disabled
X
Synch Data Transfer Enabled
Key
Jumper
Jumper NOT Installed
Jumper Installed
B-53
SCSI Hard Drive Configuration Charts
2.1 GB
Drive Size:
ST12550N
Model:
J1 Pin 1
X
W
S
P
Bit 0*
Bit 1
Bit 2
Printed
Circuit
Board
J4
*For Pluggable Drive Tray, connect
Odd Color Wire on 6-Pin SCSI ID
Connector to Bit 0 Pair.
SCSI ID Settings
Pin 1
J1 Pin 1
SCSI ID
Bit 2
Bit 1
Bit 0
0
J4
1
2
SCSI
3
POWER
4
5
6
NOTES:
1. All jumper and switch
settings are shown in
the factory default setting,
including those not labeled.
2. Termination default is
disabled/removed.
Key
Jumper NOT Installed
Jumper Installed
Default Settings
Signal Description
Jumper
S
Start Unit Command Enabled
P
Parity Enabled
W
Write Protect Disabled
X
Synch Data Transfer Enabled
Key
Jumper NOT Installed
Jumper Installed
B-54
Volume Two
SCSI Hard Drive Configuration Charts
2.1 GB
ST32171N
Model:
Bit 2
Bit 1
Bit 0
Drive Size:
J6
Pin 1
J6
Pin 1
Printed
Circuit
Board
J2
Pin 1
J2
S
W
POWER
P
SCSI
Pin 1
Pin 1
For Hot-Pluggable Drive Tray, connect
SCSI ID Cable to this Connector
SCSI ID Settings
SCSI ID
Bit 2
Bit 1
Bit 0
0
1
2
NOTES:
1. All jumper and switch
settings are shown in
the factory default setting,
including those not labeled.
2. Termination default is
disabled/removed.
3
4
5
6
Default Settings
Signal Description
Key
S
Start Unit Command Enabled
Jumper NOT Installed
P
Parity Enabled
Jumper Installed
W
Write Protect Disabled
Synch Data Transfer Enabled
Volume Two
Jumper
n/a
B-55
SCSI Hard Drive Configuration Charts
2.1 GB
Drive Size:
ST32171W
Model:
Bit 2
Bit 1
Bit 0
J6
J6
Pin 1
Printed
Circuit
Board
Pin 1
J2
J1A
J2
S
P
W
Pin 1
Pin 1
J1A
SCSI
Bit 2
Bit 1
Bit 0
POWER
Pin 1
For Hot-Pluggable Drive Tray, connect
SCSI ID Cable to this Connector
SCSI ID Settings
SCSI ID
Bit 2
Bit 1
Bit 0
0
1
2
NOTES:
1. All jumper and switch
settings are shown in
the factory default setting,
including those not labeled.
2. Termination default is
disabled/removed.
3
4
5
6
Default Settings
Signal Description
Key
S
Start Unit Command Enabled
Jumper NOT Installed
P
Parity Enabled
Jumper Installed
W
Write Protect Disabled
Synch Data Transfer Enabled
B-56
Jumper
n/a
Volume Two
SCSI Hard Drive Configuration Charts
2.1 GB
Bit 1
Drive Size:
ST32430N
Model:
Bit 0*
Pin 1
J6
J6
Pin 1
Bit 2
Printed
Circuit
Board
J2
Pin 1
*For Hot-Pluggable Drive Tray, connect Odd
Color Wire on 6-Pin SCSI ID Connector to Bit 0 Pair.
J1
NOTES:
1. All jumper and switch settings are
shown in the factory default setting,
including those not labeled.
2. Termination default is disabled/removed.
POWER
SCSI
SCSI ID Settings
SCSI ID
J2
Bit 2
Bit 1
Bit 0
0
1
S
P
2
W
X
3
4
Pin 1
5
6
Default Settings
Signal Description
S
Start Unit Command Enabled
P
Parity Enabled
W
Write Protect Disabled
X
Key
Jumper
Synch Data Transfer Enabled
Jumper NOT Installed
Jumper Installed
Volume Two
B-57
SCSI Hard Drive Configuration Charts
2.1 GB
ST32550N
Model:
Bit 1
Drive Size:
J4
Bit 0*
J2
S
P
Bit 2
W
X
Pin 1
Pin 1
*For Pluggable Drive Tray, connect
Odd Color Wire on 6-Pin SCSI ID
Connector to Bit 0 Pair.
Pin 1
J4
SCSI ID Settings
SCSI ID
Bit 2
Bit 1
Bit 0
0
Printed
Circuit
Board
1
2
3
J2
4
Pin 1
5
6
J1
Key
Jumper NOT Installed
Jumper Installed
Default Settings
POWER
SCSI
NOTES:
1. All jumper and switch
settings are shown in
the factory default setting,
including those not labeled.
2. Termination default is
disabled/removed.
B-58
Signal Description
Jumper
S
Start Unit Command Enabled
P
Parity Enabled
W
Write Protect Disabled
X
Synch Data Transfer Enabled
Key
Jumper NOT Installed
Jumper Installed
Volume Two
SCSI Hard Drive Configuration Charts
2.1 GB
Drive Size:
ST32550W
Model:
Bit 1
J2
W
X
Bit 0
Pin 1
Pin 1
Bit 2
S
P
J5
For Pluggable Drive Tray, connect
SCSI ID Cable to this Connector.
J4
SCSI ID Settings
SCSI ID
Printed
Circuit
Board
Bit 2
Bit 1
Bit 0
0
1
2
3
J2
Pin 1
4
5
J1
6
J5
Pin 1
Key
Jumper NOT Installed
Jumper Installed
Default Settings
POWER
SCSI
NOTES:
1. All jumper and switch
settings are shown in
the factory default setting,
including those not labeled.
2. Termination default is
disabled/removed.
Volume Two
Signal Description
S
Start Unit Command Enabled
P
Parity Enabled
W
Write Protect Disabled
X
Synch Data Transfer Enabled
Key
Jumper
Jumper NOT Installed
Jumper Installed
B-59
SCSI Hard Drive Configuration Charts
2.1 GB
Drive Size:
WDE2170
Model:
X
S
Bit 2
Bit 0
Pin 1
Printed
Circuit
Board
Bit 1
Pin 1
For Hot-Pluggable Drive Tray, connect
SCSI ID Cable to this Connector
Pin 1
POWER
SCSI
SCSI ID Settings
SCSI ID
Bit 2
Bit 1
Bit 0
0
1
2
NOTES:
1. All jumper and switch
settings are shown in
the factory default setting,
including those not labeled.
2. Termination default is
disabled/removed.
3
4
5
6
Default Settings
Signal Description
S
Key
B-60
Jumper NOT Installed
Jumper
Start Unit Command Enabled
Parity Enabled**
n/a
Jumper Installed
W
Write Protect Disabled
n/a
** Not Configurable
X
Synch Data Transfer Enabled
Volume Two
SCSI Hard Drive Configuration Charts
2.1 GB
WDE2170W
Model:
S
Bit 2
Bit 0
Drive Size:
X
Pin 1
Bit 1
Pin 1
Printed
Circuit
Board
For Hot-Pluggable Drive Tray, connect
SCSI ID Cable to this Connector
J1B
Pin 1
SCSI
J1B
Bit 2
Bit 1
Bit 0
Pin 1
POWER
For Hot-Pluggable Drive Tray, connect
SCSI ID Cable to this Connector
SCSI ID Settings
SCSI ID
Bit 2
Bit 1
Bit 0
0
1
2
NOTES:
1. All jumper and switch
settings are shown in
the factory default setting,
including those not labeled.
2. Termination default is
disabled/removed.
3
4
5
6
Default Settings
Signal Description
S
Key
Jumper NOT Installed
Jumper
Start Unit Command Enabled
Parity Enabled**
n/a
Jumper Installed
W
Write Protect Disabled
n/a
** Not Configurable
X
Synch Data Transfer Enabled
Volume Two
B-61
SCSI Hard Drive Configuration Charts
XP32150W
Bit 1
Model:
S
Bit 3
2.1 GB
Drive Size:
J3
Bit 0
W
Bit 2
Pin 1
Pin 1
For Pluggable Drive Tray, connect
SCSI ID Cable to this Connector.
J3
Pin 1
SCSI ID Settings
SCSI ID
Bit 2
Bit 1
Bit 0
0
Printed
Circuit
Board
1
2
3
4
5
6
Key
SCSI
Pin 1
Jumper NOT Installed
Jumper Installed
Default Settings
Signal Description
POWER
S
Jumper
Start Unit Command Enabled
Parity Enabled**
W
NOTES:
1. All jumper and switch
settings are shown in
the factory default setting,
including those not labeled.
2. Termination default is
disabled/removed.
B-62
n/a
Write Protect Disabled
Synch Data Transfer Enabled**
Key
Jumper NOT Installed
n/a
**Not Configurable
Jumper Installed
Volume Two
SCSI Hard Drive Configuration Charts
Drive Size:
1080 MB
ORION
Model:
IBM Drive
Assembly Number 186434
Position # 6 5 4 3 2 1
1
3
5
7
9 11 13 15 17 19 21 23
2
4
6
8 10 12 14 16 18 20 22 24
Pin #
SCSI ID Settings
SCSI ID
6
5
Position #
3
4
2
1
0
1
2
3
4
5
6
7
Key
Jumper NOT Installed
Jumper Installed
Volume Two
B-63
SCSI Hard Drive Configuration Charts
ST31055N
Model:
Bit 2
Pin 1
J6
Pin 1
Printed
Circuit
Board
Bit 0
J6
1080 MB
Bit 1
Drive Size:
J2
Pin 1
NOTES:
1. All jumper and switch settings are
shown in the factory default setting,
including those not labeled.
2. Termination default is disabled/removed.
POWER
SCSI
SCSI ID Settings
SCSI ID
J2
Bit 2
Bit 1
Bit 0
0
1
S
P
2
W
3
4
Pin 1
5
6
J2 Default Settings
Signal Description
S
Start Unit Command Enabled
P
Parity Enabled
W
Key
Jumper
Write Protect Disabled
Jumper NOT Installed
Jumper Installed
B-64
Volume Two
SCSI Hard Drive Configuration Charts
GND
RES
J5
A1
A0
J2
640/1280S
Model:
A2
1.05 GB
Drive Size:
J2
Printed
Circuit
Board
*For Hot-Pluggable Drive Tray, connect Odd
Color Wire on 6-Pin SCSI ID Connector to Bit 0 Pair.
NOTES:
1. All jumper and switch settings are
shown in the factory default setting,
including those not labeled.
2. Termination default is disabled/removed.
SCSI
POWER
SCSI ID Settings
SCSI ID
A2
A1
A0
0
1
PK
2
A0
TE
A1
3
A2
4
5
6
7
Jumper NOT Installed
Key
Jumper Installed
Default Settings
SCSI ID
A2
A1
A0
6
Key
Jumper NOT Installed
Jumper Installed
Volume Two
B-65
SCSI Hard Drive Configuration Charts
Fireball 1080
GND
RES
J5
A1
A0
J2
Model:
A2
1.05 GB
Drive Size:
J2
Printed
Circuit
Board
NOTES:
1. All jumper and switch settings are
shown in the factory default setting,
including those not labeled.
2. Termination default is disabled/removed.
SCSI
POWER
SCSI ID Settings
SCSI ID
A2
A1
A0
0
1
PK
2
A0
TE
A1
3
A2
4
5
6
7
Jumper NOT Installed
Key
Jumper Installed
Default Settings
SCSI ID
A2
A1
A0
6
Key
Jumper NOT Installed
Jumper Installed
B-66
Volume Two