Uniden EXI5660 - EXI 5660 Cordless Phone Setup guide

EXI5660
Series
Setup Guide
EXI5660
Step 3 Set up the Base
Step 1 Check the Package Contents
Step 5 Connect to the Phone Line
Plug the AC adapter cord to
the DC IN 9V jack (yellow).
Plug one end of the
telephone cord into
the base TEL LINE
jack.
Make sure your cordless phone’s
packaging includes the following
items.
Base
Handset
AC adapter
Belt clip
Rechargeable Telephone
battery
cord
Also included: • Owner’s manual
Step 2 Install the Handset Battery Pack
Note Use ONLY the Uniden
rechargeable battery pack
supplied with your new
phone!
Remove the
cover.
Connect the
battery pack
with the correct
polarity.
Plug the other
end into the
telephone wall
jack.
Plug the AC adapter to a
120V AC power outlet.
Step 6 Make & Receive Calls
Note Use ONLY the Uniden AC
adapter supplied with your
new phone!
To Make a Call
Press talk/flash .
Listen for dial tone.
Step 4 Charge the Handset
Place the handset in
the base.
Make sure that
charge LED
illuminates.
Dial the desired
number.
Additional Features
For more information on these
and other features, please refer to
your Owner’s Manual. For your
convenience, listed below are
important features that will help
you set up your new cordless
phone.
Handset/Base Set up:
- Adjust the Earpiece
Volume → P.25
- Set the Ringer Volume → P.25
- Set Tone/Pulse Dialing → P.17
Caller ID:
Set Caller ID on Call Waiting
(CIDCW) → P.15
Note: You must subscribe to
Caller ID services through your
local telephone provider to use
Caller ID and CIDCW.
To Receive a Call
Pick up the handset and
press talk/flash .
To Hang Up a Call
Charge for 15-20 hours before
using your phone.
Press end or return the
handset to the base.
Replace the
cover.
Refer to your Owner’s Manual for
detailed operations.
For answers to questions and to
order genuine Uniden parts and
accessories 24 hours a day visit
our website at www.uniden.com. If
you have any problems, you can
also call our Customer Hotline at
1-800-297-1023 during regular
business hours.
Guía de programación
EXI5660
3° Paso Preparación de la base
1° Paso Inspección del contenido del embalaje
Asegúrese de que haya recibido los
siguientes artículos en el paquete
Base
Receptor
Adaptador CA
5° Paso Conexión de la línea telefónica
Conecte un
extremo de la
línea telefónica en
el enchufe TEL
LINE en la base.
Conecte el adaptador CA
en el enchufe (amarillo) DC
IN 9V.
Pase el cable
Al enchufe telefónico
A la toma CA
Pinza para
Pila
Cable
la correa
recargable
telefónico
Además va incluido: • Manual del usuario
2° Instalación del paquete de pilas del receptor
Nota ¡Use SOLAMENTE el
paquete de pilas recargable
de Uniden suministrado con
su nuevo teléfono!
Conecte el
paquete de pilas rojo
con la polaridad
correcta.
Reponga la tapa
Conecte el otro extremo en el
enchufe telefónico de la pared.
Conecte el adaptador CA en
una toma de 120V CA.
6° Paso Realización y recepción de llamadas
Nota ¡Use SOLAMENTE el
adaptador CA de Uniden
suministrado con su
teléfono!
Para hacer una llamada
Oprima talk/flash .
Espere por el tono de
marcación.
Marque el número
deseado.
4° Paso Carga del receptor
Coloque el receptor
en la base.
Asegúrese de que el
LED de carga se
ilumine.
Quite la tapa.
Al enchufe TEL LINE
Cable de la línea telefónica
(suministrado)
Al enchufe DC IN 9V
Adaptador CA
(suministrado)
Para recibir una llamada
Levante el receptor y
oprima talk/flash .
rojo negro
negro
Para colgar una llamada
Cargue el receptor de 15 a 20
horas antes de usar el teléfono.
Oprima end o devuelva
el receptor a la base.
Características adicionales
Para más información sobre estas y otras
características, le rogamos que consulte su
Manual del usuario. Para su conveniencia, hemos
listado abajo unas características importantes, las
cuales le ayudarán a programar su nuevo teléfono
inalámbrico de Uniden.
Programación del receptor/base:
- Ajuste del volumen del auricular y del
altavoz → P.25
- Programación del volumen del timbre
→ P.25
- Programación de la marcación por
tono/pulso → P.17
Identificación de llamadas (Caller ID):
Programe la Identificación de llamadas en
Llamadas en espera (CIDCW) → P.15
Nota: Usted debe estar suscrito al
servicio de Identificación de llamadas
con su proveedor de telefonía local para
poder usar las características de Caller
ID y de CIDCW
Consulte su manual del usuario para
operaciones más detalladas.
Si tiene preguntas o quiere ordenar
partes y accesorios genuinos de Uniden
las 24 horas al día, visite nuestra página
en el internet ww.uniden.com.
Si tiene cualquier problema, puede llamar
a nuestra Línea Roja para el consumidor
en el 1-800-297-1023 durante las horas
regulares de oficina.
Contents
Using Call Waiting.............................................................. 26
Setup Guide....................................................................1
Selecting a Different Channel............................................ 26
Welcome/Accessibility...................................................4
Find Handset..................................................................... 26
Terminology/Manual Conventions................................5
Tone Dialing Switch-over................................................... 27
Product Overview...........................................................6
Voice Mail Waiting Indicator............................................... 27
Controls and Functions.................................................7 Caller ID and CIDCW (Caller ID on Call Waiting).......28
Installing the Phone.......................................................9
Caller ID on Call Waiting (CIDCW).................................... 29
Choosing the Best Location................................................. 9
Installing the Rechargeable Battery Pack into the
Handset........................................................................ 10
Installing the Base Unit...................................................... 11
Mounting the Base Unit on a Wall...................................... 13
Installing the Belt Clip........................................................ 14
Headset Installation........................................................... 14
Viewing the Caller ID Message List................................... 29
Deleting Information from the Caller ID List....................... 30
Changing the Digital Security Code...........................31
Maintenance..................................................................32
Troubleshooting...........................................................35
Liquid Damage................................................................... 37
Basic Setup...................................................................15 Precautions...................................................................38
The FCC Wants You To Know........................................... 39
I.C. Notice.......................................................................... 41
Activating AutoTalk............................................................. 15
Activating Caller ID on Call Waiting................................... 15
Programming Your Area Code........................................... 16
Choosing the Dialing Mode................................................ 17
Setting the Language......................................................... 18
One Year Limited Warranty..........................................42
Index..............................................................................43
Using the Speed Dial Memory.....................................19
Storing a Name and Number in Memory........................... 19
Storing Caller ID in Speed Dial Memory............................ 22
Using Your Phone.........................................................23
Making and Receiving Calls.............................................. 23
Making a Call from Speed Dial Memory............................ 23
Making a Call from the Caller ID List................................. 24
Redialing the Last Dialed Number..................................... 25
Selecting the Ring Tone and Volume................................. 25
Adjusting the Earpiece Volume.......................................... 25
Welcome
Congratulations on your purchase of the Uniden cordless telephone. This cordless phone is designed for reliability,
long life, and outstanding performance.
Note: Illustrations in this manual are used for explanation purposes. Some illustrations in this
manual may differ from the actual unit. The color of your cordless telephone may vary.
Uniden® is a registered trademark of Uniden America Corporation.
AutoTalk, AutoStandby and UltraClear Plus are trademarks of Uniden America Corporation.
Accessibility
Uniden provides a customer service hotline for accessibility questions. If you have a disability and need customer
service assistance or if you have any questions about how Uniden’s products can accommodate
persons with disabilities, please call the accessibility voice/TTY line:
1-800-874-9314.
Our customer care hours as well as accessibility information can be found on our website, www.uniden.com, under
the "Accessibility" link. If your call is received outside of our business hours, you can leave us a message and we will
call you back.
Terminology
Base
The main part of the phone that connects to your phone line and lets you make and receive calls.
Caller ID is available from your telephone provider. With this service, you can see the name and number
CID
of incoming callers.
Caller ID on Call Waiting is available from your telephone provider. With this service, you can see
CIDCW
incoming caller information while on another call.
Handset A cordless handset that can be placed anywhere in your home or office where AC power is available.
The handset may be sitting on the base charging or out of the base cradle, but is NOT in use.
Standby
[talk/flash] has not been pressed and there is no dial tone.
When a dial tone has been enabled allowing the user to dial and carry on a conversation with an outside
Talk
party.
Manual Conventions
This manual uses several different type styles to help you distinguish between different parts of the phone:
•lower case bold text with "[ ]" indicates a key or button on the phone
•ALL CAPITALS indicates text on the display, such as menu options, prompts, and confirmation messages
•lower case bold text indicates a status light on the phone base
Product Overview
Main Phone Features
• 5.8 GHz Extended Range Technology
• Caller ID/Caller ID on Call Waiting
• 3-Line Backlit LCD
• Trilingual Menu Displays (English, Spanish, or French)
• 30 Caller ID Memory
• 10 Number Memory Dialing
• Last Number Redial
• Tone/Pulse Dialing
• Page/Find Handset Key
• Earpiece/Ringer Volume Controls
• Mute or Turn Ringer Off
• Hearing Aid Compatible
• 20-Channel Auto Scan
• Desk or Wall Mountable
Controls and Functions
Handset
1. Handset antenna
2. Belt clip hole
3. Jack for optional handset
4. Handset ringer speaker
5. Handset battery compartment
6. Handset earpiece
7. LCD display
8. [ ] and [ ] (volume & ringer up/down) keys
9. [cid/menu] key
10.[ /tone/ ] (left cursor) key
11.[redial/pause] key
12.[select] key
13.[talk/flash] key
14.[end] key
15.[#/ ] (right cursor) key
16.[mem] (memory) key
17.[delete/channel] key
18.Handset microphone
19.Handset charging contacts
1
6
2
3
4
5
7
8
9
10
11
12
13
14
15
16
17
18
19
Main Base Unit
20.charge/in use LED / Voice mail waiting
indicator (flashing)
21.Base antenna
22.Base charging contacts
23.[find hs] key
24.Base DC IN 9V jack
25.TEL LINE jack
20
21
24
25
22
23
Installing the Phone
Choosing the Best Location
Before choosing a location for your new phone, here are some important guidelines you should consider:
Avoid heat sources, such as radiators,
Avoid noise sources such as a window by
air ducts, and sunlight
a street with heavy traffic
Avoid television sets and other
Avoid microwave ovens
electronic equipment
Avoid excessive moisture,
extremely low temperatures, dust,
mechanical vibration, or shock
Choose a central location
Avoid personal computers
Avoid other cordless telephones
•The location should be close to both a phone jack and a continuous power outlet (one which is not connected to a
switch).
•The base and handset should be kept away from sources of electrical noise such as motors, microwave ovens,
and fluorescent lighting.
•The base can be placed on a desk, tabletop, or mounted on a standard wall plate. For better reception, place the
base as high as possible.
•The base should be placed in an open area for optimum range and reception.
•If your home has specially wired alarm equipment connected to the telephone line, be sure that installing
the system does not disable your alarm equipment. If you have questions about what will disable your alarm
equipment, contact your telephone company or a qualified installer.
Installing the Rechargeable Battery Pack into the Handset
The handset is powered by a rechargeable battery pack. Once installed, the battery
charges automatically when the handset is placed in the base unit.
To install the rechargeable battery pack:
1) Press down on the handset battery case cover (use the finger indention for a better
grip) and slide the cover downward to remove.
2) Plug the battery pack connector (red & black wires) into the small jack inside the
battery compartment. (The connector notches fit into the grooves of the jack only
one-way.) Match the wire colors to the polarity label in the battery compartment,
connect the battery, and listen for a click to insure connection.
3) Make sure you have a good connection by slightly pulling on the battery wires. If
the connection is secure, the battery jack will remain in place.
4) Place the battery case cover back in the handset by sliding it upwards until it clicks
into place.
Note: Use only the Uniden (BT-905) rechargeable battery pack supplied
with your phone.
10
Installing the Base Unit
1) Connect the AC adapter to the DC IN 9V jack and to the
standard 120V AC wall outlet.
Note:
• Use only the supplied AD-0001 AC adapter. Do not
use any other AC adapter.
• Do not place the power cord where it creates a trip
hazard or where it could become chafed and create
a fire or electrical hazard.
2) Charge the handset by placing in the base unit with the
keypad facing forward.
11
3) Make sure that the charge/in use LED illuminates. If the LED does not
illuminate, check to see that the AC adapter is plugged in and that the
handset makes good contact with the base's charging contacts.
Note:
• Connect the AC adapter to a continuous power supply (not
controlled by a wall switch).
• Place the base unit close to the AC outlet to avoid long
extension cords.
• Charge your handset at least 15 - 20 hours before plugging into
the phone line.
4) Once the handset battery pack is fully charged, connect the telephone line
cord to the TEL LINE jack and a telephone outlet. If your telephone outlet
isn't modular, contact your telephone company for assistance.
Modular
12
Mounting the Base Unit on a Wall
Standard wall plate mounting
This phone can be mounted on any standard wall plate.
1
3
1) Plug the AC adapter to the DC IN 9V jack.
2) Plug the AC adapter into a standard 120V AC wall outlet.
5
3) Plug the telephone line cord into the TEL LINE jack.
4) Plug the telephone line cord into the telephone outlet.
4
5) Align the mounting slots on the base with the mounting posts on the
wall. Then push in and down until the phone is firmly seated.
5
2
Direct wall mounting
If you don’t have a standard wall plate, you can mount your phone directly to the wall. Before doing this, consider the
following:
•Avoid electrical cables, pipes, or other items behind the mounting location that could cause a hazard when
inserting screws into the wall.
•Try to mount your phone within 5 feet of a working phone jack to avoid excessive cord lengths.
13
•Make sure the wall material is capable of supporting the weight of the base and handset.
•Use #10 screws (minimum length of 1-3/8 inches) with anchoring devices suitable for the wall
material where the base unit will be placed.
1) Insert two mounting screws into the wall (with their appropriate anchoring device), 3-15/16
inches apart. Allow about 1/8 of an inch between the wall and screw heads for mounting the
phone.
2) Refer to steps 1 through 5 on page 13 to mount the telephone.
Installing the Belt Clip
To attach the belt clip
Insert the belt clip into the holes on each side of the handset. Press down until it clicks.
To remove the belt clip
Pull both sides of the belt clip to release the tabs from the holes.
Headset Installation
Your phone may be used with an optional headset. To use this feature, insert the headset plug into
the headset jack. Your phone is ready for hands-free conversations. (Headsets may be purchased
by visiting our website at www.uniden.com or by calling our Parts Department. See back cover
page.)
14
Basic Setup
There are five basic options that you will need to set up: AutoTalk, CIDCW (Caller ID on Call Waiting), Area Code,
Dial Mode and Language.
Activating AutoTalk
AutoTalk will allow you to answer the phone simply by removing the handset from the base. You do not have to press
a key to answer the incoming call.
To activate:
1) When the phone is in standby, press and hold [cid/menu]. The following screen appears.
2) Press [select] to turn AutoTalk on.
3) Press [end] or return the handset to the base unit to complete the setting. The handset
returns to standby.
Activating Caller ID on Call Waiting
Caller ID allows you to see the name and number of the calling party before you answer the phone. Caller ID on Call
Waiting (CIDCW) lets you see the name and number of a call that comes in when you are on the line. You must
subscribe to Caller ID service through your local telephone provider to use this feature.
1) When the phone is in standby, press and hold [cid/menu]. The following screen appears.
15
2) Press [ ] to move the pointer to select CIDCW.
3) Press [select] to toggle and turn on Caller ID on Call Waiting.
4) Press [end] and return the handset to the base unit to complete the setting. The handset
returns to standby.
Note: To enable the setting change of CIDCW, you need to return the handset to the base unit when
you complete the setting.
Programming Your Area Code
In some areas the telephone company may allow you to place a local call by dialing only 7 digits (instead of 10).
If this is the case in your area, you can program your local area code in your phone. Programming your area code
will allow you to see the caller’s 7-digit phone number which will allow you to easily return the local call without
modifying the number before dialing. If you get a call from outside your area code, you'll see all 10 digits.
To program your area code:
1) When the phone is in standby, press and hold [cid/menu]. The following screen appears.
2) Press [ ] to move the pointer to select AREA CODE.
3) Press [select]. If an area code was already stored, the phone will display it.
4)
5)
6)
Use the number keys ( [0] – [9] ) to enter the 3-digit area code.
If you make an error, use [delete/channel] to backspace.
Press [select]. A confirmation tone sounds.
Press [end] or return the handset to the base unit to complete the setting. The handset returns to standby.
16
Choosing the Dialing Mode
Your phone can communicate with the telephone network in two different ways: tone dialing and pulse dialing. These
days, most telephone networks use a method called tone dialing, so your phone comes programmed for tone dialing
by default.
If your phone company uses pulse dialing, you'll need to change your phone's dial mode. There's an easy way to tell:
try making a call. If your call connects, your phone's setting is fine. If not, you may need to change the dial mode.
To change the dial mode:
1) When the phone is in standby, press and hold [cid/menu]. The following screen appears.
2) Press [ ] to move the pointer to select DIAL.
3) Press [select] to set the phone to pulse dialing.
4) Press [end] or return the handset to the base unit to complete the setting. The handset
returns to standby.
Note: If your phone system requires pulse dialing and you need to send the DTMF tones during a
call, you can temporarily switch over to tone dialing. (Refer to "Tone Dialing Switch-over" on page
27.)
17
Setting the Language
You can change the language the handset menu displays. Choose from English, French, or Spanish.
To change the language setting:
1) When the phone is in standby, Press and hold [cid/menu]. The following screen appears.
2) Press [ ] to move the pointer to select LANGUAGE.
3) Press [select] to select ENG, FR. or ESP.
4) Press [end] or return the handset to the base unit to complete the setting. The handset returns to standby.
18
Using the Speed Dial Memory
Your cordless phone allows you to store up to 10 names and numbers in the handset. You can dial these numbers
with just a few key presses. The speed dial memory is not limited to phone numbers. You can store any number
(up to 20 digits) that you need to enter once your call connects. This is referred to as Chain Dialing. An example
is a frequently refilled prescription number. Store your pharmacy phone number in one speed dial and your most
frequently refilled prescription number as another speed dial. To use, once you ring your pharmacy's automated
prescription line, simply press [mem] and the speed dial number where you stored your prescription number and
press [select].
Note: When editing the speed dial memory, you must press a key within 30 seconds or the phone
will return to standby. If you return the handset to the base, the phone will return to standby also.
Storing a Name and Number in Memory
1) With the phone in standby, press [mem].
2) Enter [0] - [9] or use [ ] and [ ] to select the speed dial location where you would like to
store this entry, and then press [select] twice.
3) STORE NAME appears and a cursor flashes indicating that the phone is ready for the
name to be entered.
Note: If the selected speed dial number is already assigned, the Edit screen
appears. You can select EDIT MEMORY to edit this entry, select DELETE
MEMORY to erase this entry, or select GO BACK to choose another speed dial
number.
19
4) Enter a name according to the instructions below, then press [select]. If no name is required, go to step 5.
•The name can be up to 13 characters.
•Use [ /tone/ ] and [#/ ] to move the cursor to the desired location.
•Press [delete/channel] to delete characters as needed or press and hold to delete all characters.
Refer to the letters on the number keys to select the desired characters.
With each press of a numeric key, the displayed character appears in the following order: upper case letters first,
lower case letters next and finally the number corresponding to the key.
Note: If the next character uses the same number key, you must press [#/ ] to move the cursor over.
Otherwise the next time you press the number key, it changes the character that was previously set.
For example, to enter Movies.
1) Press [6] once. Then press [#/ ] to
move the cursor to the right.
2) Press [6] six times.
3) Press [8] six times.
4) Press [4] six times.
5) Press [3] five times.
6) Press [7] eight times.
Number of times key is pressed
keys
1
2abc
3def
4ghi
5jkl
6mno
7pqrs
8tuv
9wxyz
0 oper
20
1
2
3
4
5
6
7
8
9
If you make a mistake while entering a name
Use [ /tone/ ] or [#/ ] to move the cursor to the incorrect character.
Press [delete/channel] to erase the wrong character. Then enter the correct character. To delete all characters,
press and hold [delete/channel].
5) STORE NUMBER is displayed. The cursor flashes indicating that the phone is ready for
the number to be entered.
6) Use the keypad to enter the phone number; each number can be up to 20 digits. If you
need the phone to pause during the dialing sequence, press [redial/pause] to insert a
two-second delay between the numbers. You can enter multiple pauses to increase the
delay. Each pause counts as a digit. The display shows a P for every pause.
7) Press [mem]. You will hear a confirmation tone, and the following screen appears.
Memory storage is complete.
8) After about 2 seconds, the following screen displays all the speed dial memory entries.
9) Press [end] to exit memory setup mode. The phone returns to standby.
Note: When storing numbers into memory, if the handset is idle (i.e., no key is pressed) for more
than 30 seconds, it will beep rapidly, and the phone will return to standby.
21
Storing Caller ID in Speed Dial Memory
Caller ID names and numbers shown in the Caller ID list can be stored in speed dial memory.
To store a caller id name/number to memory:
1) With the phone in standby, press [cid/menu]. Select the phone number to be stored from
the Caller ID list by pressing [ ] or [ ].
2) Press [mem].
3) Enter a number ( [0] – [9] ) or press [ ] or [ ] to select the memory location to be stored.
4) Press [select]. You hear a confirmation tone, and the number is stored in memory. The
display returns to the Caller ID list.
Note:
• If a number has already been stored in the selected memory number
location, a confirmation screen is displayed. To overwrite, press [ ] to YES
and press [select]. The display returns to the Caller ID list.
• You cannot store a Caller ID message if no phone number appears in the message.
22
Using Your Phone
Making and Receiving Calls
Making a call
Receiving a call
Hanging up
Handset on the base
1) Pick up the handset from the base.
2) Press [talk/flash].
3) Listen for the dial tone.
4) Dial the number.
OR
1) Pick up the handset from the base.
2) Dial the number. Then press [talk/flash].
1) Pick up the handset from the base. (If
AutoTalk is on, the phone will answer the
call when you pick it up.)
2) Press [talk/flash].
Press [end] or return the handset to the base.
Handset off the base
1) Press [talk/flash].
2) Listen for the dial tone.
3) Dial the number.
OR
Dial the number. Then press [talk/flash].
Press [talk/flash] (or [ /tone/ ], [#/ ] or any
number key if AutoTalk is on).
Note: To turn on the AutoTalk feature, see "Activating AutoTalk" on page 15.
Making a Call from Speed Dial Memory
To make a call from speed dial memory:
1) With the phone in standby, press [mem]. The handset displays your programmed speed
dial number.
23
2) Enter the number ( [0] – [9] ), or press [ ] or [ ] to select the speed dial number you would like to dial.
3) Press [talk/flash]. TALK and the volume setting and the number selected appear on the
display. Then the displayed number is dialed.
Note: You can also press [talk/flash] before you access the speed dial memory.
When you come to the phone number you want to dial, press [select].
To cancel speed dialing
Press [end] to return to standby. If accessing the list during an active call, you can press [mem] to exit the list
immediately. If no key is pressed for 30 seconds, the handset will exit the speed dial list automatically.
Note: Pressing [end] to exit the speed dial list during a call will disconnect the call immediately.
Making a Call from the Caller ID List
You can place a call directly from the Caller ID list.
1) Press [cid/menu] in standby. Use [ ] or [ ] to select the phone number that you want to
dial.
2) To have the phone dial a "1" before the displayed Caller ID number, press [1]. To have the
phone dial the stored area code before the displayed Caller ID number, press [3].
3) Press [talk/flash]. The displayed phone number dials automatically.
Note:
• You can also press [talk/flash] before you access the Caller ID list. When you come to the phone
number you want to dial, press [select].
• You cannot make a call from the Caller ID list if your cordless telephone is connected to a private
branch exchange (PBX).
24
Redialing the Last Dialed Number
1)
2)
3)
4)
Pick up the handset from the base.
Press [talk/flash].
Listen for the dial tone.
Press [redial/pause].
OR
1) Pick up the handset from the base.
2) Press [redial/pause].
3) Press [talk/flash].
Selecting the Ring Tone and Volume
Your phone has five different ringer tone/volume combinations you can choose from.
To select the ringer:
1) With the phone in standby, press [ ] or [ ].
2) The phone will sound the different ring tones at different volumes. To turn the ringer
off, select RINGER OFF.
3) When the phone sounds the ring tone and volume you wish to use, press [end].
Temporarily Mute Ringer
If the handset is off the base while an incoming call is ringing, simply press [end] to mute
the incoming ring. The ringer will sound with the next incoming call.
Note: You can only mute the handset ringer if the handset is off the base when the phone starts
ringing.
Adjusting the Earpiece Volume
To change the earpiece volume, press [ ] or [ ] during a call.
25
Using Call Waiting
If you subscribe to Call Waiting through your local telephone company, you can receive calls while on the line.
To answer a call waiting call:
1) While on the phone, you will hear a call waiting tone. (If you have CIDCW service
activated, you will see the name and number of the incoming caller. See page 28 for
more information)
2) Press [talk/flash] to accept the waiting call. After a short pause, you will hear the new
caller.
3) To return to the original caller, press [talk/flash] again.
Selecting a Different Channel
Your phone incorporates UltraClear Plus™ true compander circuitry which virtually
eliminates background noise. This innovative technology, together with 20 different
channels, provides you with the best possible reception during all your conversations. If
you happen to encounter interference while using your phone, you can manually change
the phone’s channel for clear operation. To change the channel during a call, press
[delete/channel]. SCANNING appears on the display, indicating the phone is changing
to another channel. For more information on interference, refer to "Radio Interference" on
page 40.
Find Handset
To locate a lost handset, press [find hs] on the base. The handset will beep for 60
seconds. The beeping will stop when any handset key is pressed, when the handset is
returned to the base, or when [find hs] is pressed. The handset will also stop beeping
automatically when an incoming call is received.
26
Tone Dialing Switch-over
If your telephone company requires pulse dialing, you can temporarily switch over to tone
dialing after the call connects. This feature is useful when you need tone dialing to use
automated such as telephone bank tellers, telephone prescription refills, customer support
menus, etc.
If your phone is set to pulse dialing mode, make your call normally. Once your call
connects, press [ /tone/ ]. Any digits you enter from then on will be sent as tone dialing.
When this particular call ends, the phone automatically returns to pulse dialing mode.
Voice Mail Waiting Indicator
If you subscribe to voice mail service through your local telephone company, you can use your cordless telephone to
access your voice mailbox. The voice mail company will provide you with the access number.
The charge/in use LED on the base of your phone flashes whenever you have messages waiting in your voice
mailbox.
To access your voice mailbox
Just dial the access number supplied by your voice mail provider to enter your mailbox.
You can program your voice mail access number to a speed dial number.
If the voice mail waiting indicator remains on after you have retrieved your messages, press and hold [find hs] for
5 seconds. This will reset the indicator.
27
Caller ID and CIDCW (Caller ID on Call Waiting)
You must subscribe to Caller ID services through your local telephone provider to use these features.
When the telephone rings, the Caller ID feature allows you to view the caller’s name, phone number, date and time
of call. The incoming call information is stored in the Caller ID record. If the Caller ID service includes the caller’s
name, the caller’s name appears on the display (up to 15 letters).
The date and
time received
Caller's name
Caller's phone number
You may receive any one of the following messages:
When invalid data is received INCOMPLETE DATA
When a private name is received PRIVATE NAME
When a private number is received PRIVATE NUMBER
When an unknown name is received UNKNOWN NAME
When an unknown number is received UNKNOWN NUMBER
Note:
• Data errors appear as " ".
• If you answer a call before the Caller ID message is received (for example, before the second ring),
the Caller ID message will not appear.
• When the call is received via a telephone company that does not offer Caller ID service, the caller’s
phone number and name do not appear. (This includes international calls.)
• When the call is received via a private branch exchange (PBX), the caller’s phone number and
name may not appear.
28
Caller ID on Call Waiting (CIDCW)
If you subscribe to CIDCW offered by your telephone company, you will hear a Call Waiting tone while you are on a
call, and the Caller ID data will be displayed at the handset. To accept the waiting call, press [talk/flash] (see page
26).
Viewing the Caller ID Message List
The Caller ID list stores information for up to 30 incoming calls - even unanswered calls. You can also view the Caller
ID list during a call.
1) Press [cid/menu]. The summary screen displays the number of new messages and total
messages.
2) Use [ ] to scroll through the messages from the latest to the earliest, or use [ ] to scroll
through the messages from the earliest to the latest.
3) Press [cid/menu] to return to the call, or press [end] to return to standby.
Note:
• In Caller ID operation, if no key is pressed for more than 30 seconds, an error tone sounds and the
handset returns to standby.
• Each message can be up to 15 characters for the name and 15 digits for the phone number.
• The number of calls from the same Caller ID appears next to the received time. Once you view the
new message, the number will be cleared and disappear.
• During a call, don't press [end], or the call will be disconnected.
29
Deleting Information from the Caller ID List
If the phone receives more Caller ID messages than it can store, the oldest one in the list is automatically deleted.
Caller ID data can also be deleted manually.
Deleting a Caller ID message
1) Press [cid/menu] in standby. Find the message to be deleted from the Caller ID list by
pressing [ ] or [ ].
2) Press [delete/channel].
3) Press [ ] or [ ] to select YES, and then press [select].
Deleting all Caller ID names/numbers
1) With the phone in standby, press [cid/menu].
2) Press [delete/channel].
3) Press [ ] or [ ] to select YES, and then press [select].
You hear a confirmation tone and all stored Caller ID messages are deleted.
Note:
• While using the DELETE ALL? or DELETE MESSAGE? screen, if no key is pressed for more than
30 seconds, an error tone sounds, and the handset returns to standby.
• If you get an incoming call or page, the deleting operation is canceled and you can answer the call
or page.
30
Changing the Digital Security Code
To protect you against misbilled calls which might result from your phone being activated by other equipment, the
cordless phone provides AutoSecure™ (which electronically locks your phone when the handset is in the base)
and Random Code™ digital security which automatically selects one of over 262,000 digital security codes for the
handset and the base. If the handset battery pack is completely discharged or the battery pack is removed, the
digital security code will be lost. If this happens, a new security code is set automatically the next time the battery
pack is charged. In the rare situation that you suspect another cordless telephone is using the same security code,
you can change the code.
1) Pick up the handset from the base unit. Press and hold [find hs] on the base.
2) While holding [find hs], place the handset in the base, and leave the handset in the base for more than 3
seconds. A new random security code is set.
31
Maintenance
Specifications
The phone complies with FCC Parts 15 and 68.
Operating temperature
AC Adapter
Battery
Frequency
-10°C to +50°C (+14°F to +122°F)
Part number
AD-0001
Input Voltage
120V AC 60Hz
Output Voltage
9V DC 210mA
Part number
BT-905
Capacity
600mAh, 3.6V
921.103102-923.787761 MHz
5856.533347-5863.692437 MHz
Note: To avoid damage to the phone use only Uniden AD-0001 and BT-905 with your phone.
Specifications, features, and availability of optional accessories are all subject to change without prior notice.
Power Failure
During the period that the power is off, you will not be able to make or receive calls with the telephone.
32
Talk and Standby Times
With average use, your handset battery provides approximately 6 hours of talk time and approximately 10 days
of standby time. When your handset is not being used and is left off of the base unit, the battery will gradually
discharge. You can achieve optimum battery life and performance by returning the handset to the base unit after
each use. If the handset is left off of the base unit, the actual talk time duration will be reduced respective to the
amount of time the handset is off of the base unit.
Low battery alert
When the battery pack is very low and needs to be charged, the phone is programmed to
eliminate functions in order to save power. If the phone is not in use, LOW BATTERY appears
on the LCD and none of the keys will operate. During a call, LOW BATTERY flashes and the
handset beeps. Complete your conversation as quickly as possible and return the handset to the base unit for
charging.
Note: Information stored in the phone's memory will be retained for 30 minutes after the battery pack
is removed. This includes all setup information, last number dialed, speed dial memory, and the CID
list.
Even when the battery pack is not being used, it will gradually discharge over a long period of time. For optimum
performance, be sure to return the handset to the base unit after a telephone call.
33
Battery replacement and handling
Recharge your phone on a regular basis by returning the handset to the base after each phone call. When the
operating time becomes short even after a battery is recharged, please replace the battery. With normal usage, your
battery should last about one year. To order replacement batteries, please contact Uniden’s Parts Department. The
contact information is listed on the back cover page.
Warning:
Caution
•Use only the specified Uniden battery pack (BT-905).
To avoid the risk of personal injury or
•Do not remove the battery from the handset to charge it.
property damage from fire or electrical
•Never throw the battery into a fire, disassemble it, or heat it.
shock, only use the Uniden battery
•Do not remove or damage the battery casing.
model and Uniden adapter model
specifically designated for this product.
Cleaning the battery charging contacts
To maintain a good charge, clean the charging contacts on the handset once
a month. Dampen a cloth with plain water. Gently rub the damp cloth over the
charging contacts until all visible dirt is removed. Dry the contacts thoroughly
before returning the handset to the base.
Caution
Do not use paint thinner, alcohol, or other chemical products. Doing so
may discolor the surface of the telephone and damage the finish.
34
Troubleshooting
Traveling Out-of-Range
During a call, as you begin to move your handset too far from your base unit, noise increases. If you pass the range
limits of the base, your call will terminate within one minute.
Common Issues
If your phone is not performing to your expectations, please try these simple steps first. If these steps do not solve
your problem, please call our Customer Hotline. See back cover page for contact information.
Symptom
The charge/in use LED won't
illuminate when the handset is
placed in the base.
The audio sounds weak and/
or scratchy.
Can’t make or receive calls.
Suggestion
•Make sure the AC adapter is plugged into the base and wall outlet.
•Make sure the handset is properly seated in the base.
•Make sure the charging contacts on the handset are clean.
•Move the handset and/or base away from metal objects or appliances and try
again.
•Press [delete/channel] during a call to help eliminate background noise.
•Make sure that the handset is not too far from the base.
•Check both ends of telephone line cord.
•Make sure the AC adapter is plugged into the base and wall outlet.
•Disconnect the AC adapter for a few minutes, then reconnect it.
•Change the digital security code (see page 31).
•Make sure that the handset is not too far from the base.
•Check the dialing mode used by your telephone company.
35
Symptom
The handset doesn’t ring or
receive a page.
Severe noise interference.
The Caller ID does not
display.
Voice Message Indication
does not work.
Suggestion
•The battery pack may be weak. Charge the battery for 15-20 hours.
•The handset may be too far away from the base unit.
•Place the base unit away from appliances or metal objects.
•Change the digital security code (see page 31).
•Check the battery pack to ensure there is a secure connection.
•Make sure ringer volume isn’t set to "off."
•Keep the handset away from microwave ovens, computers, remote control toys,
wireless microphones, alarm systems, intercoms, room monitors, fluorescent
lights, and electrical appliances.
•Move the base to another location or turn off the source of interference.
•The call was answered before the second ring.
•The call was placed through a switchboard.
•Charge the handset.
•Your Caller ID service may not be active; contact your local telephone service
provider.
•Contact your local telephone company to make sure that your telephone receives
FSK message signaling.
•Reset the indicator by pressing and holding [find hs] for 5 seconds.
36
Liquid Damage
Moisture and liquid can damage your cordless phone.
•If the handset or base is exposed to moisture or liquid, but only the exterior plastic housing is affected, wipe off the
liquid, and use as normal.
•If moisture or liquid has entered the plastic housing (i.e. liquid can be heard in the phone or liquid has entered the
handset battery compartment or vent openings on the base), follow the steps below:
Handset
1) Remove the battery cover and leave it off for ventilation.
2) Disconnect the battery pack. Leave the battery cover off
and the battery pack disconnected for at least 3 days.
3) Once the handset is completely dry, reconnect the
battery pack and the battery cover.
4) Recharge the handset's battery pack for 15 to 20 hours
before using.
Base
1) Disconnect the AC adapter from the base,
cutting off electrical power.
2) Disconnect the telephone cord from the base.
3) Let dry for at least 3 days.
IMPORTANT:
You must unplug the telephone line while recharging the battery pack to avoid charge interruption.
CAUTION:
DO NOT use a microwave oven to speed up the drying process. This will cause permanent damage to the handset,
base and the microwave oven. After following these steps, if your cordless telephone does not work, please call our
Customer Service Hotline. See back cover page for contact information.
37
Precautions!
Rechargeable Nickel-Cadmium
Batteries Must Be Recycled or
Disposed of Properly
Before you read anything else, please note the following:
Warning!
•Uniden voluntarily participates in an RBRC®
industry program to collect and recycle nickelcadmium batteries at the end of their useful life, when taken
out of service within the United States.
•The RBRC® program provides a convenient alternative to
placing used nickel-cadmium batteries into the trash or
municipal waste stream, which is illegal in some areas.
•Through the RBRC® program, Uniden makes it easy for you
to drop off the used battery at local retailers of replacement
nickel-cadmium batteries. You may also contact your local
recycling center for information on where to return the used
battery.
Please call 1-800-8-BATTERY for information on Ni-Cd battery
recycling in your area. Uniden’s involvement in this program
is part of its commitment to protecting our environment and
conserving natural resources.
•RBRC® is a registered trademark of the Rechargeable Battery
Recycling Corporation.
Uniden works to reduce lead content in our PVC coated cords
in our products and accessories.
Uniden America Corporation DOES NOT represent this unit
to be waterproof. To reduce the risk of fire, electrical shock,
or damage to the unit, DO NOT expose this unit to rain or
moisture.
Rechargeable Nickel-Cadmium Battery Warning
•This equipment contains a rechargeable nickel-cadmium
battery.
•Cadmium is a chemical known to the State of California to
cause cancer.
•The rechargeable nickel-cadmium battery contained in this
equipment may explode if disposed of in a fire.
•Do not short-circuit the battery.
•Do not charge the rechargeable nickel-cadmium battery used
in this equipment in any charger other than the one designed
to charge this battery as specified in the owner's manual.
Using another charger may damage the battery or cause the
battery to explode.
Warning!
The cords on this product and/or accessories contain lead, a
chemical known to the State of California to cause birth defects
or other reproductive harm. Wash hands after handling.
38
Important Safety Instructions
The FCC Wants You To Know
When using your telephone equipment, basic safety
precautions should always be followed to reduce the risk of fire,
electric shock and injury to persons, including the following:
1. Do not use this product near water, for example, near a
bath tub, wash bowl, kitchen sink or laundry tub, in a wet
basement or near a swimming pool.
2. Avoid using a telephone (other than a cordless type) during
an electrical storm. There may be a remote risk of electric
shock from lightning.
3. Do not use the telephone to report a gas leak in the vicinity
of the leak.
4. Use only the power cord and batteries indicated in this
manual. Do not dispose of batteries in a fire. They may
explode. Check with local authorities for possible battery
disposal instructions.
5. Do not disassemble any component of this product.
This equipment complies with Part 68 of the FCC rules and the
requirements adopted by the ACTA.
On the bottom of this equipment is a label that contains,
among other information, a product identifier in the format US:
AAAEQ##TXXXX. If requested, this number must be provided
to the telephone company.
An applicable Universal Service Order Codes (USOC)
certification for the jacks used in this equipment is provided (i.e.,
RJ11C) in the packaging with each piece of approved terminal
equipment. A plug and jack used to connect this equipment to
the premises wiring and telephone network must comply with
the applicable FCC Part 68 rules and requirements adopted by
the ACTA.
A compliant telephone cord and modular plug is provided with
this product. It is designed to be connected to a compatible
modular jack that is also compliant. See installation instructions
for details.
The REN is used to determine the number of devices that may
be connected to a telephone
line. Excessive RENs on a telephone line may result in the
devices not ringing in response to an incoming call. In most but
not all areas, the sum of RENs should not exceed five (5.0). To
be certain of the number of devices that may be connected to
a line, as determined by the total RENs, contact the telephone
provider. For products approved after July 23,
2001, the REN for this product is part of the product identifier
that has the format US:AAAEQ##TXXXX. The digits
represented by ## are the REN without a decimal point (e.g.,
03 is a REN of 0.3). For earlier products, the REN is separately
SAVE THESE INSTRUCTIONS
CAUTION!
Risk of explosion if battery is replaced by an incorrect type.
Dispose of used batteries according to the instructions. Do not
open or mutilate the battery, and disconnect the battery before
shipping this product.
39
shown on the label.
If this equipment causes harm to the telephone network, the
telephone company will notify you in advance that temporary
discontinuance of service may be required. But if advance
notice isn't practical, the telephone company will notify the
customer as soon as possible. Also, you will be advised of
your right to file a complaint with the FCC if you believe it is
necessary. The telephone company may make changes in its
facilities, equipment, operations or procedures that could affect
the operation of the equipment. If this happens the telephone
company will provide advance notice in order for you to make
necessary modifications to maintain uninterrupted service.
Please follow instructions for repairing, if any (e.g. battery
replacement section); otherwise do not substitute or repair
any parts of the device except as specified in this manual.
Connection to party line service is subject to state tariffs.
Contact the state public utility commission, public service
commission or corporation commission for information. This
equipment is hearing aid compatible.
Should you experience trouble with this equipment, please
contact Uniden customer service at 800-297-1023. If the
equipment is causing harm to the telephone network, the
telephone company may request that you disconnect the
equipment until the problem is resolved.
NOTICE: According to telephone company reports, AC electrical
surges, typically resulting from lightning strikes, are very
destructive to telephone equipment connected to AC power
sources. To minimize damage from these types of surges, a
surge arrestor is recommended.
Changes or modifications to this product not expressly
approved by Uniden, or operation of this product in any way
other than as detailed by the owner's manual, could void your
authority to operate this product.
This device complies with part 15 of the FCC rules. Operation
is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) This device must accept
any interference received, including interference that may cause
undesired operation. Privacy of communications may not be
ensured when using this phone.
To insure the safety of users, the FCC has established
criteria for the amount of radio frequency energy various
products may produce depending on their intended usage.
This product has been tested and found to comply with the
FCC's exposure criteria. For body worn operation, the FCC RF
exposure guidelines were also met when used with the Uniden
accessories supplied or designed for this product. Use of other
accessories may not ensure compliance with FCC RF exposure
guidelines and should be avoided.
Radio Interference
Radio interference may occasionally cause buzzing and
humming in your cordless handset, or caused by external
sources such as TV, refrigerator, vacuum cleaner, fluorescent
lighting, or electrical storm. Your unit is NOT DEFECTIVE. If
these noises continue and are too distracting, please check
around your home to see what appliances may be causing
the problem. In addition, we recommend that the base not
be plugged into a circuit that also powers a major appliance
because of the potential for interference. Be certain that
the antenna on the unit is fully extended when needed. In
40
I.C. Notice
the unlikely event that you consistently hear other voices or
distracting transmissions on your phone, you may be receiving
radio signals from another cordless telephone or other source
of interference. If you cannot eliminate this type of interference,
you need to change to a different channel. Finally, it should be
noted that some cordless telephones operate at frequencies
that may cause interference to nearby TVs and VCRs. To
minimize or prevent such interference, the base of the cordless
telephone should not be placed near or on top of a TV or VCR.
If interference is experienced, moving the cordless telephone
farther away from the TV or VCR will often reduce or eliminate
the interference.
Terminal Equipment
NOTICE: This equipment meets the applicable Industry Canada
Terminal Equipment Technical Specifications. This is confirmed
by the registration number. The abbreviation, IC, before the
registration number signifies that registration was performed
based on a Declaration of Conformity indicating that Industry
Canada technical specifications were met. It does not imply that
Industry Canada approved the equipment
NOTICE: The Ringer Equivalence Number (REN) for this
terminal equipment is marked on the equipment itself. The REN
assigned to each terminal equipment provides an indication
of the maximum number of terminals allowed to be connected
to a telephone interface. The termination on an interface may
consist of any combination of devices subject only to the
requirement that the sum of the Ringer Equivalence Numbers of
all the devices does not exceed five.
Cordless Telephone Privacy
Cordless telephones are radio devices. Communications
between the handset and base of your cordless telephone
are accomplished by means of radio waves which are
broadcast over the open airways. Because of the inherent
physical properties of radio waves, your communications can
be received by radio receiving devices other than your own
cordless telephone unit. Consequently, any communications
using your cordless telephone may not be private.
Radio Equipment
The term "IC:" before the radio certification number only
signifies that Industry Canada technical specifications were
met. Operation is subject to the following two conditions: (1) this
device may not cause interference, and (2) this device must
accept any interference, including interference that may cause
undesired operation of the device. "Privacy of communications
may not be ensured when using this telephone".
41
One Year Limited Warranty
IMPLIED OR ARISING BY OPERATION OF LAW, INCLUDING,
BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE. THIS WARRANTY DOES NOT COVER OR
PROVIDE FOR THE REIMBURSEMENT OR PAYMENT
OF INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some
states do not allow this exclusion or limitation of incidental or
consequential damages so the above limitation or exclusion
may not apply to you.
LEGAL REMEDIES: This warranty gives you specific legal
rights, and you may also have other rights which vary from
state to state. This warranty is void outside the United States
of America and Canada. PROCEDURE FOR OBTAINING
PERFORMANCE OF WARRANTY: If, after following the
instructions in the owner's manual you are certain that the
Product is defective, pack the Product carefully (preferably in
its original packaging). Disconnect the battery from the Product
and separately secure the battery in its own separate packaging
within the shipping carton. The Product should include all parts
and accessories originally packaged with the Product. Include
evidence of original purchase and a note describing the defect
that has caused you to return it. The Product should be shipped
freight prepaid, by traceable means, to warrantor at:
Uniden America Service
4700 Amon Carter Blvd.
Fort Worth, TX 76155
Important: Evidence of original purchase is required for warranty
service. WARRANTOR: UNIDEN AMERICA CORPORATION
("Uniden") ELEMENTS OF WARRANTY: Uniden warrants, for
one year, to the original retail owner, this Uniden Product to be
free from defects in materials and craftsmanship with only the
limitations or exclusions set out below.
WARRANTY DURATION: This warranty to the original user
shall terminate and be of no further effect 12 months after the
date of original retail sale. The warranty is invalid if the Product
is (A) damaged or not maintained as reasonable or necessary,
(B) modified, altered, or used as part of any conversion kits,
subassemblies, or any configurations not sold by Uniden, (C)
improperly installed, (D) serviced or repaired by someone
other than an authorized Uniden service center for a defect
or malfunction covered by this warranty, (E) used in any
conjunction with equipment or parts or as part of any system
not manufactured by Uniden, or (F) installed or programmed by
anyone other than as detailed by the owner's manual for this
product.
STATEMENT OF REMEDY: In the event that the product does
not conform to this warranty at any time while this warranty is
in effect, warrantor will either, at its option, repair or replace
the defective unit and return it to you without charge for parts,
service, or any other cost (except shipping at its option, may
replace the unit with a new or refurbished unit. THE LIMITED
WARRANTY SET FORTH ABOVE IS THE SOLE AND ENTIRE
WARRANTY PERTAINING TO THE PRODUCT AND IS IN
LIEU OF AND EXCLUDES ALL OTHER WARRANTIES OF
ANY NATURE WHATSOEVER, WHETHER EXPRESS,
42
Index
A
D
S
AC adapter information.................. 32 Dial mode....................................... 17 Speed dial memory
Digital security code....................... 31
Making calls from speed dial
memory............................... 23
B
Storing names and numbers in
Basic setup..................................... 15 E, F, G, H, I, J, K, L
speed dial memory............. 19
Battery pack
Earpiece volume............................. 25
Information.................................. 32 Find handset................................... 26
Installing..................................... 10 Headset Installation........................ 14 T, U
Preparing and charging........ 10, 11 Installing the phone.......................... 9 Talk and standby times................... 33
Replacement and handling......... 34 Interference.................................... 40 Technical information...................... 32
Belt clip installation......................... 14 Liquid damage................................ 37 Tone dialing switch-over................. 27
Traveling out-of-range.................... 35
Troubleshooting.............................. 35
C
M, N, O, P, Q
Caller ID service............................. 28 Maintenance................................... 32
Caller ID on call waiting.............. 29 Making a call.................................. 23 V, W, X, Y, Z
Deleting...................................... 30 Precautions.................................... 38 Voice mail waiting indicator............ 27
Wall mounting................................. 13
Making a call............................... 24
Warranty......................................... 42
Viewing....................................... 29 R
Call waiting..................................... 26 Receiving a call.............................. 23
Channel.......................................... 26 Redial............................................. 25
Charging the battery pack.............. 11 Ringer tone and volume................. 25
Cleaning contacts........................... 34
Controls and functions.................. 7, 8
43
Memo
44
Memo
45
At Uniden, we’ll take care of you!
Thank you for purchasing a Uniden product. If you have any questions or problems,
please do not return this product to the place of purchase.
Having Trouble?
Need a Part?
Help for our
Special Needs
Customers
Our customer care specialists are here to help you! Visit our website at www.uniden.com or
call our Customer Hotline at 1-800-297-1023 during regular business hours.*
To order headsets, additional handsets, replacement batteries or other accessories, visit our
website at www.uniden.com or call 1-800-554-3988 during regular business hours.*
If you need special assistance due to a disability or have questions on the accessibility
features of this product, please call 1-800-874-9314 (voice or TTY).
* Central Standard Time. Detailed customer service hours are available at www.uniden.com.
May be covered under one or more of the following U.S. patents:
4,797,916 5,426,690 5,434,905 5,491,745 5,493,605 5,533,010
5,574,727 5,581,598 5,650,790 5,660,269 5,661,780 5,663,981
5,671,248 5,696,471 5,717,312 5,732,355 5,754,407 5,758,289
5,768,345 5,787,356 5,794,152 5,801,466 5,825,161 5,864,619
5,893,034 5,912,968 5,915,227 5,929,598 5,930,720 5,960,358
5,987,330 6,044,281 6,070,082 6,125,277 6,253,088 6,314,278
6,418,209 6,618,015 6,671,315 6,714,630 6,782,098 6,788,920
6,788,953 6,839,550 6,889,184 6,901,271 6,907,094 6,914,940
6,953,118 7,023,176
Other patents pending.
46