Provision ISR DAI-390IP04 User manual

PROVISION-ISR
 DAI-310IP04
 I3-310IP04
 DI-310IPVF
 DAI-390IP04
 I3-390IP04
 DI-390IPVF
 DAI-390IP04
 I3-390IP04
 DI-390IPVF
User Manual
IP Camera
For H.264 IP Camera
All rights reserved
Notes
 Before operation, we strongly advise users to read this manual and keep it properly for
using later.
 Please use the specified power supply to connect.
 Avoid from incorrect operation, shock vibration, heavy pressing which can cause
damage to product.
 Do not use corrosive detergent to clean main body of the camera. If necessary, please
use soft dry cloth to wipe dirt; for hard contamination, use neutral detergent. Any
cleanser for high grade furniture is applicable.
 Avoid aiming the camera directly towards extremely bright objects, such as, sun, as this
may damage the image sensor.
 Please follow the instructions to install the camera. Do not reverse the camera, or the
reversing image will be received.
 Do not operate the camera in extreme temperatures or extreme humidity conditions.
 Use the power supply supplied authorized by a PROVISION-ISR technician.
 Keep away from heat sources such as radiators, heat registers, stove, etc.
 The instructions in this manual could be outdated; if you need any clarifications you can
contact an authorized PROVISION-ISR technician. PROVISION-ISR reserves the
right to add changes to this manual and publish it online in our website
(www.provision-isr.com): there may be inconsistencies with the latest version. This
applies to any and all software upgrades and product improvements, interpretation and
modification added. These changes will be published in the latest version without
prior notification.
 When this product is in use, the relevant contents of Microsoft, Apple and Google will
be involved in. The pictures and screenshots in this manual are only used to explain
the usage of our product. The ownerships of trademarks, logos and other intellectual
properties related to Microsoft, Apple and Google belong to the above-mentioned
companies.
 All pictures and examples used in the manual are for reference only.
IP CAMERA USER MANUAL
Table of Contents
1 2 Introduction.........................................................................................................1 IE Remote Access .................................................................................................2 2.1 2.2 3 4 Access through IP-Tool......................................................................................... 2 2.1.2 Directly Access through IE.................................................................................... 3 WAN .................................................................................................................................. 4 Remote Preview ...................................................................................................6 3.1 The Remote Preview Interface .............................................................................................. 6 3.2 Playback ............................................................................................................................. 7 3.3 Snap Pictures....................................................................................................................... 7 Remote Live Surveillance .....................................................................................9 4.1 4.2 4.3 4.4 4.5 5 LAN ................................................................................................................................... 2 2.1.1 System Configuration ........................................................................................................... 9 4.1.1 Basic Information................................................................................................. 9 4.1.2 Date & Time Configuration ................................................................................... 9 Video Configuration ........................................................................................................... 10 4.2.1 Camera Configuration ........................................................................................ 10 4.2.2 Video Stream ..................................................................................................... 11 4.2.3 OSD Configuration ............................................................................................ 11 4.2.4 Video Mask ....................................................................................................... 12 4.2.5 ROI Configuration ............................................................................................. 13 Alarm Configuration .......................................................................................................... 14 4.3.1 Motion Detection Area ....................................................................................... 14 4.3.2 Motion Detection Trigger .................................................................................... 14 4.3.3 Motion Detection Schedule ................................................................................. 15 Network Configuration ....................................................................................................... 16 4.4.1 Port .................................................................................................................. 16 4.4.2 IP Address ......................................................................................................... 16 4.4.3 Server Configuration .......................................................................................... 17 4.4.4 IP Notify ........................................................................................................... 17 4.4.5 DDNS Configuration .......................................................................................... 18 4.4.6 RTSP ................................................................................................................ 21 4.4.7 UPNP ............................................................................................................... 21 4.4.8 Mail Setting ....................................................................................................... 22 4.4.9 FTP .................................................................................................................. 22 Advanced Configuration ..................................................................................................... 23 4.5.1 User Configuration ............................................................................................. 23 4.5.2 Security Configuration........................................................................................ 25 4.5.3 Configure Backup & Restore ............................................................................... 25 4.5.4 Reboot Device ................................................................................................... 26 4.5.5 Upgrade ............................................................................................................ 26 Mobile Surveillance............................................................................................27 5.1 Network Configuration ....................................................................................................... 27 IP CAMERA USER MANUAL
6 7 5.2 By Phones with iPhone OS ................................................................................................. 27 7.3
By Phones with Android .................................................................................................................. 33
IP-Tool...............................................................................................................36 Q & A ................................................................................................................39 Page 1
1
IP CAMERA USER MANUAL
Introduction
This IP-CAMERA (short for IP-CAM) is designed for high performance CCTV solutions. It
adopts state of the art video processing chips. It utilizes most advanced technologies, such as
video encoding and decoding technology, complies with the TCP/IP protocol, SoC, etc to
ensure this system more stable and reliable. This unit consists of two parts: the IP-CAM
device and central management software (short for CMS). The CMS centralizes all devices
together via internet or LAN and establishes a sound surveillance system to realize unified
management and remote operation to all devices in one network.
This product is widely used in banks, telecommunication systems, electricity power
departments, law systems, factories, storehouses, uptowns, etc. In addition, it is also an ideal
choice for surveillance sites with middle or high risks.
Main Features









ICR auto switch, true day/night
3D DNR, digital WDR
ROI coding
Support CVBS output
Support MIC IN
PoE power supply
Support smart phone, iPad, remote monitoring (Via Provision CAM/HD)
Vandal-proof
Support P2P (NET Traversal)
Page 2
IP CAMERA USER MANUAL
2 IE Remote Access
You may connect IP-Cam via LAN or WAN. Here only take IE browser (6.0) for example.
The details are as follows:
2.1 LAN
In LAN, there are two ways to access IP-Cam: 1. access through IP-Tool; 2. directly access
through IE browser.
2.1.1 Access through IP-Tool
① Make sure the PC and IP-Cam are connected to the LAN and the IP-Tool is installed in the
PC from the CD.
② Double click the IP-Tool icon on the desktop to run this software as shown below:
③ Modify the IP address. The default IP address of this camera is 192.168.226.201. Click the
information of the camera listed in the above table to show the network information on the
right hand. Modify the IP address and gateway of the camera and make sure its network
address is in the same local network segment as the computer’s. Please modify the IP address
of your device according to the practical situation.
For example, the IP address of your computer is 192.168.13.4. So the IP address of the camera
shall be changed to 192.168.13.X. After modification, please input the password of the
Page 3
IP CAMERA USER MANUAL
administrator and click “Modify” button to modify the setting.

The default password of the administrator is “123456”.
④ Double click the IP address and then the system will pop up the IE browser to connect
IP-CAM. IE browser will auto download the Active X control. After downloading, a login
window will pop up as shown below.
Input the username and password to log in.

The default username is “admin”; the default password is “123456”.
2.1.2 Directly Access through IE
The default network settings are as shown below:
IP address: 192.168.226.201
Subnet Mask: 255.255.255.0
Gateway: 192.168.226.1
HTTP: 80
Data port: 9008
You may use the above default settings when you log in the camera for the first time.
① Manually set the IP address of the PC and the network segment should be as the same as
the default settings of the IP camera. Open the network and share center. Click “Local Area
Connection” to pop up the following window.
Page 4
IP CAMERA USER MANUAL
Select “Property” and then select internet protocol according to the actual situation (for
example: IPV4). Next, click “Property” button to set the network of the PC.
② Open the IE browser and input the default address of IP-CAM and confirm. The IE
browser will download Active X control automatically.
③ After downloading Active X control, the login dialog box will pop up.
④ Input the default username and password and then enter to view.
2.2 WAN
Take access the camera by the router or virtual server for example
① Make sure the camera is well connected via LAN and then log in the camera via LAN and
go to the ConfigNetwork ConfigPort menu to set up the port number.
Page 5
IP CAMERA USER MANUAL
② Go to Config Network ConfigWired menu to modify the IP address.
③ Go to the router’s management interface through IE browser to forward the IP address and
port of the camera in the “Virtual Server”.
Port Setup
IP Setup
Router Setup
④ Open the IE browser and input its WAN IP and http port to access.
Page 6
IP CAMERA USER MANUAL
3 Remote Preview
3.1 The Remote Preview Interface

1
People icon
6
Full screen
2
Fix size
7
Start recording
3
Actual size
8
Playback
4
Zoom in
9
Snap
5
Zoom out
10
Enable audio
When motion detection alarm is triggered, the people icon will turn red.
Right click to pop up a pull-down list as shown below:
Stream: Three streams are optional.
Turn off the live: Click this item to close present live preview.
Full screen: The live preview picture will be full-screen display.
Double click or click right mouse to return to the previous
interface.
Online user: Display the current user connecting to the device.
System information: Display the device information: device name,
firmware version, software build date, kernel version and hardware version.
Page 7
IP CAMERA USER MANUAL
3.2 Playback
Before you play the record files, please make sure you have recorded. You may click
button to record. Then click
button to pop up a video player. Double click the record file
to play the video as shown below.
1
Play
5
Next frame
9
Zoom out
2
Pause
6
The previous file
10
Full screen
3
Stop
7
The next file
11
Path
4
Forward
8
Zoom in
12
Volume
3.3 Snap Pictures
Select the picture number, and then click “Snap”
Single Snap
icon as shown below:
Page 8
IP CAMERA USER MANUAL
Snap multiple pictures
Select the picture number from Frame pull down list box, such as 2, and check “Title” and
“Time” to show capture title and time on the snap pictures simultaneously.
Multi-picture Snap
Page 9
IP CAMERA USER MANUAL
4 Remote Live Surveillance
Functions of remote configurations include: System Configuration, Video Configuration,
Alarm Configuration, Network Configuration and Advanced Configuration. You should
firstly select the menu on the left, and then set up the relative parameters. When one user
configures parameters of a certain device, other users can not set up this device.
4.1 System Configuration
The “System configuration” includes two submenus: Basic Information and Date & Time.
4.1.1 Basic Information
In the “Basic Information” interface, you can set up the device name and can also check the
relative information of the server
Setting steps:
1. Clicking the “Config” icon will appear the menu list.
2. Clicking the “Basic Information” will pop up a window as shown below:
3. Input the name of the device in the “Device name” text box.
4. Press the “Save” button to save the settings.
Please refer to the following table for parameters and instructions of server basic
configuration.
Parameter
Meaning
Software version
The software of the device
Software build date
The software build date of the device
Kernel version
The kernel version of the device
Hardware version
The hardware version of the device
Mac Address
MAC address of device
Maximum number of user
Support max 10 users to access
Device name
Name of the device.
4.1.2 Date & Time Configuration
Setting steps:
1. Go to ConfigDate & Time menu as shown below.
Page 10
IP CAMERA USER MANUAL
2. Set time zone.
3. Enable DST mode as required.
4. Set time. You may set time manually or enable NTP.
4.2 Video Configuration
Camera Configuration includes five submenus: Camera Configuration, Video Stream, OSD
Config, Video Mask and ROI Config.
4.2.1 Camera Configuration
Setting steps:
1.Go to “Video Configuration”  “Camera” interface as shown below.
2. You may adjust brightness, contrast, hue and saturation of the picture.
3. Select white balance mode.
4. Wide dynamic, sharpen, and denoise are adjustable.
5. You can also set day-night mode and enable the image mirror and image overturn function.
6. You may frequency and repair bad pixel.
7. Press the “Save” button to save the settings.
Page 11
IP CAMERA USER MANUAL
4.2.2 Video Stream
Go to “Video configuration” “Video Stream” to see an interface as shown below.
Three video streams can be adjustable.
Resolution: The higher the resolution is, the clearer the image is.
Frame rate: The higher the frame rate is, the more fluency the video is. However, more
storage room will be taken up.
Bitrate type: Including CBR and VBR. CBR means that no matter how changeable the video
resources are, the compression bitrate keeps constant. This will not only facilitate the image
quality better in a constant bitrate but also help to calculate the capacity of the recording.
VBR means that the compression bitrate can be adjustable according to the change of the
video resources. This will help to optimize the network bandwidth .
Video Quality: When VBR is selected, you need to choose image quality. The higher the
image quality you choose, the more bitrate will be required.
Bitrate: Please choose it according to the actual network situation.
I Frame interval: It is recommended to use the default value. If the value is over high, the
read speed of the group of pictures will be slow resulting in the quality loss of the video.
Video encoding profile: Baseline, main profile and high profile are optional. Baseline profile
is mainly used in interactive application with low complexity and delay. Main or high profile
is mainly used for higher coding requirement.
Alarm picture size: Please select it according to the actual situation.
Video encode slice split: If enabled, you may get more fluency image even though using the
low-performance PC.
4.2.3 OSD Configuration
Go to “Video Config”  “OSD Config” menu to display the interface as shown below.
Page 12
IP CAMERA USER MANUAL
You may set time stamp, device name and custom OSD here. Drag the time stamp and custom
OSD to set their position. Then press the “Save” button to save the settings.
4.2.4 Video Mask
You can set 4 mask areas at most.
To set up video mask
1. Enable video mask and select mask color.
2. Click “Draw” button and then drag the mouse to draw the video mask area.
3. Click “Save” button to save the settings.
4. Return to the live to see the following picture.
Page 13
IP CAMERA USER MANUAL
Clear the video mask:
Go to video mask menu and then click “Clear” button to delete the current video mask area.
4.2.5 ROI Configuration
To set up ROI
1. Go to ConfigROI Config menu.
2. Check “Enable” and then click “Draw” button.
3. Drag the mouse to set the ROI area.
4. Set the level.
5. Click “Save” button to save the settings.
Now, you will see the selected ROI area is clearer than other areas especially in low bitrate
condition.
Page 14
IP CAMERA USER MANUAL
4.3 Alarm Configuration
Alarm configuration includes three submenus: Motion Detection Area, Motion Detection
Trigger and Motion Detection Schedule.
4.3.1 Motion Detection Area
1. Go to “Alarm configuration” “Motion Detection Area” to see an interface as below.
2. Move the “Sensitivity” scroll bar to set up the motion trace sensitivity.
3. Check the “Add”, press the “Ctrl” button and move mouse to select the motion detection
area. Select “Erase” and move the mouse to clear all motion detection area.
4. Press the “Save” button to save the settings.
4.3.2 Motion Detection Trigger
1. Go to “Alarm Configuration”  “Motion Detection Trigger” to display an interface as
shown below.
2. Check “Enable alarm” check box. Then all functions under this interface will be activated.
3. Trigger Email: Check “Attach picture” and the triggered snap pictures will be sent into the
address.
4. Trigger FTP: Check “Uploading picture”. Then the triggered snap pictures will be sent into
FTP server address. Please refer to FTP configuration chapter for more details.
5. Press the “Save” button to save the settings.
Page 15
IP CAMERA USER MANUAL
4.3.3 Motion Detection Schedule
Go to “Alarm configuration” “Motion Detection schedule” interface as shown below.
Week schedule
User could set the alarm time from Monday to Sunday for alarm everyday in one week.
Add: Add the schedule for a special day.
Erase: Delete holiday schedule.
Day schedule
You could set alarm time for alarm in some time of special day, such as holiday.
1. Select a date at the “Date” pull down list, press “Add” button to add that date to the list box
on the right side and then move the scroll bar to set the schedule of that day.
2. Select a date in the list box on the right side, and press “Erase” to remove the schedule on
Page 16
IP CAMERA USER MANUAL
that day.
Press the “Save” button to save the settings.
Note: Holiday schedule is prior to Week schedule.
4.4 Network Configuration
Network configuration includes eight submenus: Port, IP Address, Server Configuration, IP
Notify, DDNS Config, RTSP, UPNP, Mail Setting and FTP.
4.4.1 Port
1. Go to “Network config” “Port” to see the interface as shown below.
2. Input port number for IE access in the “HTTP Port” textbox.
3. Input the port number for audio & video transmission in the “Data Port” textbox.
4.4.2 IP Address
1. Go to “Network Configuration” “IP Address”.
Page 17
IP CAMERA USER MANUAL
2. There are two options for IP setup: obtain an IP address auto by DHCP protocol and use the
following IP address. You may choose one of options as required.
3. Use the following IP address: display the IP address, subnet mask, gateway and DNS of the
device.
4. PPPoE: User needs to manual input the user name and password for dial-up internet.
Firstly, log in IE clients and then enter user name and password of PPPoE, save the setting
and exit. Secondly, set up IP address change notice. Thirdly, connect with Modem. Then the
device will dial up internet automatically.
5. Press the “Save” button to save the settings.
4.4.3 Server Configuration
Go to “Network Configuration” “Server Config”.
1. Check “Do you want IP Camera to connect Server”.
2. Check the IP address and port of the transfer media server in the CMS/NVMS. Then enable
the auto report in the CMS/NVMS when adding a new device. Next, self-define the device ID
and input the remaining information of the device in the CMS/NVMS.
3. Input the above-mentioned server IP, server port and device ID in the responding boxes.
4.Click “Save” button to save the settings.
4.4.4 IP Notify
1. Go to “Network Configuration” “IP Notify” to see a tab as shown below.
2. If the “Enable notifying change of IP” is selected, when the IP address of the device is
changed, a new IP address will be sent to the appointed mailbox automatically; If “FTP” is
selected, when the IP address of the device was changed, a new IP address will be sent to FTP
server.
Page 18
IP CAMERA USER MANUAL
4.4.5 DDNS Configuration
1. Domain name Registration (http://provision-isr-dns.com)
Note: DDNS is used to register for a hostname with
DDNS username and password.
Provision ISR now allows you to use our mint DDNS server in order to
create a virtual address for your DVR/NVR/IP-Camera on the internet.
Each account is limited to 35 different addresses using your preferred
domain name address instead of using IP addresses. Follow the steps
below to register your DVR's name and to configure your DVR to use
Provision ISR's Mint DDNS server.
(a) To register a domain with Provision-ISR DDNS server follow these steps:
1)
Visit our website:
http://provision-isr-dns.com
and register for a domain name
by clicking "Registration"
2)
Fill in the registration form, then click
"Submit"
3)
Fill in the host name you want to apply for
and press "Request
Domain" (for
example "home")
4)
If there is no problem with the domain registration you will see the following
message: “Your domain was successfully created.”
If you do not see this
message, the domain name
you requested is already in
use and you will be requested
Page 19
IP CAMERA USER MANUAL
to provide an alternate domain name (please note: domain name is sometimes called
host name).
You can create up to 35 domain records under a single account
5)
The domain name is added at the beginning of your DVR's address, for example the
domain "home" will appear as home.provision-isr-dns.com.
1. Enter into "Network Configuration""DDNS Configuration" tab as below:
Note: The steps to band a domain name for video surveillance server are as follows.
Firstly, register a user name and a password to log on the website of service supplier,
and then apply for a domain name online for the server. After that, users can visit the
server through inputting the domain name at IE terminal.
2. Press the "Save" button to save the settings.
Please refer to the following table for parameters and instructions of DDNS
configuration.
Parameter
Meaning
Address of the website which provided by domain name supplier. The
DDNS server
optional: www.dns2p.net , www.88ip.net ,www.meibu.com ,
www.dyndns.com,www.no-ip.com,www.3322.org and mintdns type.
User name
Log in the website of domain name supplier
Password
Log in the website of domain name supplier
1. Apply the Domain Name (Take dns2p for example)
(1) Register in the Web
Page 20
IP CAMERA USER MANUAL
Register dialog box
Step 1: Fill in the blank of IE address with ‘www.dns2p.com’.
Step 2: Click
to enter the website.
Step 3: Click "New User" in the right of homepage to register. For example: User ID is ‘abc’,
and password is ‘123456’. The register dialog display as above.
(2)
Login
Step 1: Return to homepage after registering successfully.
Step 2: Click "Account Manager" on the right of homepage to login.
Step 3: Input the username and password with the information that you have registered.
Step 4: Click "Enter" key after filling in the textbox.
Log in
(3) Domain Setup
Step 1: Click "Domain Management" on the left to set the domain.
Domain setup
Step 2: Input the domain in the textbox. For example, you set ‘IP-CAMERA’ as the domain.
Step 3: Click "Submit" button, the system will pop up a dialog box to show that the domain is
added successfully.
Note: Time of probationary period is one month. If user wants to use it continuatively
after one month, please Step 4: click "Buy Now" in the right of homepage to pay for it.
Page 21
IP CAMERA USER MANUAL
2. Setup in the IP-CAMERA
⑴
DOMAIN
Domain is set in ‘1. Apply the Domain Name’. According to the example above, the
domain is ‘WWW. IP-CAMERA.dns2p.com’.
⑵
USER ID
Username of registered which is set in ‘(1) Register in the Web’. According to the
example above, user ID is ‘abc’.
⑶
PASSWORD
Password is set in ‘(1) Register in the Web’. According to the example above, password
is ‘123456’.
Note: If the connection fails, press the "INFO" button. Now the system will display:
‘DDNS NONE’. Then you need to check network and information above and try again.
3. Application
Connect IP-CAMERA to the Network Client.
Step 1: After popping up the login interface, fill in "Server" textbox with ‘*.dns2p.com’ to
visit the Network Client of the IP-CAMERA. The domain set in ‘(3) Domain Setup’.
According to the example above, fill in "Server" textbox with ‘IP-CAMERA.dns2p.com’.
Step 2: Click "save" button to save the above setting.
4.4.6 RTSP
Go to “Network Configuration” “RTSP” interface as shown below.
1. Select “Enable RTSP server”.
2. RTSP Port: Access Port of the streaming media. The default number is 554.
3. RTSP Address: The RTSP address you need to input in the media player.
4. You can also choose to enable anonymous viewer login.
4.4.7 UPNP
Go to “Network Configuration” “UPNP” interface as shown below.
Page 22
IP CAMERA USER MANUAL
Select “Enable UPNP” and then input friendly name.
Then double click “Network” icon on the desktop of the PC to see an icon with the friendly
name and IP address of the camera. You may quickly access the device by double clicking
this icon.
4.4.8 Mail Setting
Go to “Network Configuration”  “Mail Setting” interface.
1. From Email: sender’s e-mail address.
2. User name and password: sender’s user name and password.
3. Server address: SMTP name of sender.
4. Select the secure connection type at the Secure Connection pull down list according to user’
actual needs.
5. Receival email address list: add email address into the list.
6. Receival email address: receiver’s e-mail address.
7. After all parameters set up, you can click “Test your account settings”. If email sent
successful, a “Test Successful” window will pop up, if not, users can try other email addresses
or check the setting.
Notice: If you change the static IP into PPPoE and select mailbox, there will be an e-mail sent
to your mail box for notifying a new IP address.
4.4.9 FTP
Go to Network ConfigurationFTP interface as shown below.
Page 23
IP CAMERA USER MANUAL
1. Add: Click Add button to input FTP server’s server name, address, port number, user name,
password, and upload path, click OK to confirm the setting.
2. Modify:Click this button to change some information of the FTP server.
3. Delete:Select certain FTP account; Click this button to delete this account.
4. Test :Select certain FTP account; Click this button to test its validity.
Please refer to the following table for parameters and instructions of FTP configuration.
Parameter
Meaning
Server name
The name of the FTP server
Server address
The address of the FTP server
Port
The port number of the FTP server
User name
The user name of the FTP server
Password
The password of the FTP server
Path
The save path for FTP files
4.5 Advanced Configuration
Advanced configuration includes four submenus: User Configuration, Security Configuration,
Configure Backup & Restore, Reboot and Upgrade.
4.5.1 User Configuration
Go to Advanced configurationUser Configuration interface.
Add user:
1. Clicking “Add” button pops up “Add user” dialog box.
Page 24
IP CAMERA USER MANUAL
User Configuration
Add User
Note: After binding physical address to the IP-CAM, you can access the device on this PC in
network only. If the MAC address was “00:00:00:00:00:00” which means it can be connected
to any computers.
2. Input user name in “User Name” textbox (only letters).
3. Input characters in “Password” and “Confirm Password” textbox (letters or numbers).
4. Input the MAC address of the PC in “Binding MAC address” textbox.
5. Click “OK” button and then the new added user will display in the user list.
Modify user:
1. Select the user which needs to modify password and physical address in the user
configuration list box.
2. Clicking “Modify” button will pop up “Modify user” dialog box as shown below.
Modify User
3. Input original password of this user in the “Password” text box.
4. Input new password in the “New password” and “Confirmation” text box.
5. Input computer’s physical address which is used to access the server in the “User PC
MAC” text box.
6. Click “OK” button to modify password and binding MAC address successfully.
Delete user:
1. Select the user which needs to delete in the user configuration list box.
2. Clicking “Delete” button will pop up a confirm dialog box. Then click “OK” to delete the
user.
Page 25
IP CAMERA USER MANUAL
Note: The default super administrator cannot be deleted.
Parameter
Meaning
User Name
User name to operate the logon client end
User Type
Type of users, normal user, advanced user and super administrator
Binding MAC address
The MAC addresses of user access the server which should set up
according to actual MAC address of server.
Password
Password to log in the client terminal
Confirm Password
Password to log in the client terminal
4.5.2 Security Configuration
1. Go to Advanced ConfigurationSecurity Configuration to see a tab shown below.
2. Check “Enable IP address” check box, select “Deny the following IP address”, input IP
address in the IP address list box and click “Add” button. Then this IP address will display in
the list box; the operation step of “Allow the following IP address” is the same with “Deny
the following IP address”.
3. Select the IP address which needs to be deleted from the IP address list box and click
“Delete” button to delete that IP address.
4. Check “Enable MAC address” check box, select “Deny the following IP address”, input
MAC address in the MAC address list box and click “Add” button. Then this MAC address
will display in the list box; the operation step of “Allow the following MAC address” is the
same with “Deny the following IP address”.
5. Select the MAC address which needs to be deleted from the MAC address list box and
click “Delete” button to delete that MAC address.
6. Click “Save” button to save the above setting.
4.5.3 Configure Backup & Restore
Go to Advanced configurationConfigure Backup & Restore Interface.

Import & Export Configuration:
Page 26
IP CAMERA USER MANUAL
You can import or export the setting information from PC or to device.
1. Click “Browse” to select save path for import or export information on PC.
2. You can import or export all setting information to PC, but those two settings “User
Configuration” and “Network Configuration” are exceptional.

Default Configuration
Click “Load default” button to restore all system settings to the default status.
4.5.4 Reboot Device
Go to Advanced configuration—Reboot device to see an interface as shown below.
Click “Reboot device” button to reboot the device.
4.5.5 Upgrade
Go to Advanced Configuration—Upgrade interface as shown below.
1. Click “Browse” button to select the save path of the upgrade file.
2. Click “Upgrade server firmware” button to start upgrading the application program.
3. The device will restart automatically.
4. After you successfully update the software, click “OK” button to close IE and then re-open
IE to connect IP-Cam.
Notice: You can’t disconnect to PC or close the IP-CAM during upgrade.
Page 27
IP CAMERA USER MANUAL
5 Mobile Surveillance
This IP-CAM supports mobile surveillance by phones with Windows mobile, iPhone,
Android and Blackberry OS. Please check the operation system version of mobile
before use; and connect the IP-CAM to Internet.
5.1 Network Configuration

Access device via LAN
Step 1: Connect device via wireless router. Then checkmark DHCP both in router and
device to automatically acquire IP address or enter the IP address manually.
Step 2: Use WIFI function in your mobile phone to connect the wireless router.
Note: Make sure your phone network and device network are in the same network
segment on LAN.
Step 3: Add the IP address and port in the mobile phone surveillance client.

Access device via 3G network
Step 1: Set the device network. Please enter Main MenuSetupNetwork tab.
If you use PPPoE to connect device, please enable PPPoE and input username and
password received from you ISP in network tab. Then click “Apply”. You can enter
Main MenuInformationNetwork tab to see the IP address. If you want to utilize
dynamic domain name, please apply for a domain name in a DNS server supported by
the device.
If you have a static WAN IP address, please enter Main MenuSetupNetwork
tab to input your IP address, gateway and port.
If you use LAN IP address, please enter Main MenuSetupNetwork tab to
input your IP address, gateway and port and then forward IP address and port number in
virtual server setup of the router or virtual server(If you has enabled the UPnP function
in both the device and router, you can skip this step). Port forwarding setting may be
different in different routers and servers. Please refer to the router’s manual for details.
After you forward your LAN IP address and port, please check the WAN IP address in
the router or server.
Step 2: Add the WAN IP address or
domain name in mobile phone surveillance
client.
5.2 By Phones with iPhone OS

Install through Iphone.
Step 1: Open App Store software as shown in the
Page 28
IP CAMERA USER MANUAL
figure on the left.
Step2: Search “Provision Cam” and click “Free” button as shown in the figure on the right.
Step 3: Click “Install App” button as shown in
the figure on the left.
Step 4: Input iTunes Store password and then
click “OK”. The software will be installed
automatically.

Install Software through
PC
Step 1: Install iTunes store in PC
and then login.
Step 2: Connect iPhone and PC.
Step 3: Search and select
“Provision Cam”.
Step 4: Click “Download” button.
Step 5: Input username and password.
Step 6: Synchronously apply "Provision
Cam" software to iPhone/iPad.

"Provision Cam" Instruction
1. Login
Step 1: Choose network type. There are two network
connection ways: 3G/3G +WIFI, enhanced video quality.
This network supports main stream and sub stream. The
real-time image will be displayed by using sub stream.
Page 29
IP CAMERA USER MANUAL
3G, normal video quality compared to the former network type.
Step 2: Input server, account and password.
Server: WAN IP address (or domain name) plus HTTP port of the device. For example:
210.21.183:89 or 123.dvrdydns.com:89.
Note: The default http port of the device is 80. If modified, use the modified port.
Account and Password: The login account and password of the device. The default
account is admin and the default password is 123456.
Step 3: Click【Login】button to access the device.
2.
Main Interface
There are many buttons in the main interface, such as,
screen mode, favorite channel, snap, record,
open/close audio, talk, PTZ., etc.
:Image view button. The pictures snapped in the
live will be checked by clicking this button.
:Playback button. Click this button to enter into
playback interface.
:Settings button. Click this button to set local
configuration (Some can also support remote configuration).
:Information button. Click this button to check lots of information including local
information, device information, network information, etc.
:Server list button. Click this button to add server list.
:Help button. Help you know about the use of this software quickly.
:CMS button. Make you preview the live image of multi-devices.
:Log off button. Click this button to return to the login interface.
:Screen mode button. You can choose 1,4,6,8,9,
13 or 16 screen display mode.
:Favorite channel display button. If you save your favorite channel in the favorite
server list, clicking this button will directly play all favorite channels you have saved.
:Snap button. Choose the channel and click this button to capture the channel
image.
:Local record button. Choose the channel and click this button to start recording.
Page 30
IP CAMERA USER MANUAL
: Open/Close audio. Choose the channel and click this button to open/close the
audio of this channel.
:Open/Close talk. Click this button to pop up the servers which support talk
function. Select the device to start talking.
:Set video parameter button. Select the channel and click this button to set the
video parameters including brightness, hue, saturation and contrast.
:PTZ button. Click this button to pop up PTZ control panel.
:Choose bitrate priority or quality priority according to
your network condition.
Channel indicator instruction:
:Video loss
: Schedule recording
:Sensor alarm
:Motion alarm
:Others
:Motion /sensor alarm based recording or manual recording
3.
Server list
Click
button to pop
up the following picture.

Add device: Click “Add”
button in the top right corner to
pop up a dialog box as shown in
the following left picture. Input
the relative information of the
device and click “Save” button.
 Delete device: Click
button behind the device name to delete this device.
 Edit device: Click
button behind the device name to edit the information of this
device.
 Backup & restore: It is recommended to click “Backup” button to reserve the
information of all devices. Then you can click “Restore” button to restore all device
information after you re-install the client or delete the device uncarefully.

indicates the device has been connected;

indicates the device is connecting;

indicates the device is not connected.
Page 31
4.
IP CAMERA USER MANUAL
Live Preview
Once you access the device, the system will automatically display the screen mode
in accordance with the channel number of the device
Note: The maximum number of channels which can be connected are nine after
login.
1.
Click “Screen mode” button to select channel as shown in Fig 1.
2.
When there is video playing in a screen, you can switch the channel by long pressing
the screen as shown in Fig 2.
3.
When no video is playing in a screen, click this screen to choose channel as shown in
Fig 3.
4.
When the single channel is playing, you can zoom in/out the image by swiping you
finger up and down as shown in Fig 4.
5.
When the single channel is playing, the channel can be switched by swiping your
finger left or right as shown in Fig 5.
6.
When multi channels are playing, drag one channel screen to the other channel
screen. This will make these two channels change the position of each other.
Fig 1
Fig 2
Fig 3
Page 32
IP CAMERA USER MANUAL
Fig 4
5.
CMS Function
This function makes multi-device managements and
preview come true.
Step 1: Click
to enable CMS function. When this
icon turns green, it means this function is enabled.
Step 2: Click
to choose channel as shown in the
right picture. After you choose the channel, click “ok”,
the system will display the related image automatically.
 If channels have been added into the group, you can see
the images by clicking the group name.
 On viewing the group channel images, click
button
and select channels to check other channel images.
 Click “Exit CMS” to exit CMS mode and return to the
main interface of the device.
6.
Favorite Channel/Group
There are two kinds of favorite channels: favorite
channels of the device and favorite group of CMS.
 Favorite channels of the device
Step 1: Click
to enter into device management list.
Click the device name to extend channel. Enlighten the
channels to save favorite channels as shown in the
following picture on the left.
Step 2: Return to the main interface and click
button to play the favorite channels.
 Favorite groups of CMS
Fig 5
Page 33
IP CAMERA USER MANUAL
Enable CMS function and enlighten the group to save the favorite groups as shown in
the following picture on the right.
Then click
button to play. Only one favorite group can be collected.
:Color means the channel or group has been collected. Grey means the channel
or group isn’t collected.
7.
Playback Interface
Click “Playback” button to enter the playback interface.
Then click “Search” button to search the file. To play the
record by click this file name.
8.
Image View
Click
9.
button to view the captured pictures.
Settings Interface
In this interface, you can configure the local settings.
10.
Information Interface
In this interface, you can view system information.
7.3 By Phones with Android
Software Installation
Step 1: Run “Play Store” (or Google
market) program.
Step 2: Search “Provision Cam”.
Page 34
IP CAMERA USER MANUAL
Step 3: Press “Install” button.
Step 4: Install the software subject
downloading is done, the software
automatically
to the notes. Once the
will install
Login Menu
Step 1: Configure the network of
mobile phone.
your
device
and
Step 2: Input the WAN IP address/domain name and port of your device in the sever
column. The port should be HTTP port of your device. The default http port of the
device is 80. If you have changed your http port, please enter the new port here. For
example: 210.21.228.183:89 or 123.dvrdydns.com:89.
Step 3: Input the account and
password of your device. The default
account name is admin and the
default password is 123456.
Step 4: Check “Remember Server” to
save the setting. When you login next
time, you can click
button to
select this server for quick access.
PTZ
Snap
Record
Talk
Enable/disable audio
Hide
Playing favorite channel
Main Menu
Live View
The
first
picture
The previous
picture
Next picture
The last picture
Zoom in
Zoom out
Delete
Page 35
IP CAMERA USER MANUAL
Record Playback:
Click “Playback” in the main menu interface to enter playback interface. Then choose
the channel you want to playback. This will take you to see the record file. Click this
file to play.
Pause/Play
Stop
Forward
Backward
Server List:
In the main
menu interface, click “Server list” to see the above picture on
the left hand.
Add Server: Click
button to pop up a window as
shown in the above picture on the right hand. Enter the name,
server, user and password of the device you want to add.
Then click “Save” button to save the server. When you log in
next time, you can choose and quickly access this server by
clicking the little triangle button in the server column.
Modify Server: Click
button to modify the server information. Delete Server:
Click
button to delete the
server information.
Settings:
In the main menu interface, click
“Settings” to enter the settings
interface where you can configure
local settings. Click “Local” to
enter local settings interface. In
this interface, you can set favorite
Page 36
IP CAMERA USER MANUAL
channel and storage.
Favorite Channel:
Check the favorite channels and click “Save” button to save these channels. Then go
into live interface and click
button to play these favorite channels.
Storage: Setup the relevant parameters of mobile video.
Information View: view the DVR/NVR basic information as shown in the picture on
the right.
6
IP-Tool
Updating through IP-Tool
Note: Do not cut off power supply and internet when updating. If the device is
unable to start because of the failure of upgrade, it needs to retrofit.
Acquire the IP-Tool from the supplier and then double click the IP-Tool icon
to
run this software. Then the device can be searched; if the device can’t be searched,
please check whether the PC and the device connect to the network or not.
Click the device to check its detail information as shown below:
Page 37
IP CAMERA USER MANUAL
When upgrading the software and kernel, the IP address of PC and device should be at
the same network segment. If the network segment is different, user should change the
IP address by right clicking the device and then select “network setup”. Modify IP
address dialog box will appear as follows:
Modify IP address and click OK button to exit the dialog box. After that, IP-Tool will
display the new IP address.

Upgrade Software
Select the device; right click “Update software”. Click “Update” to start upgrading,the
progress bar will display as below. When upgrading, please do not disconnect PC and
the device and make sure the power is on.
Page 38
IP CAMERA USER MANUAL
After finishing upgrading, a massage box will pop up as below:
Click OK button to exit the update dialog box, and then the device will restart
automatically. Select the device and right click it to select “Update kernel”. This will
bring up a dialog box as below:
Input the relevant information and click “Browse” button to choose your update file.
After that, click “Update Kernel” button to start updating. When upgrading, do not
disconnect PC to device and make sure the power is on. The update progress bar will
display as below:
After finishing upgrading, a message box will pop up. After a while, the device will
restart automatically.
Page 39
7
IP CAMERA USER MANUAL
Q &A
1. Q: How to find my password if I forget it?
A:Hold and press the default hole with spicula to reset.
Default IP: 192.168.226.201
User name: admin
Password: 123456
2. Q:Fail to connect devices through IE browser, why?
A: Network doesn’t connect well. Please check the connection and make sure it
connected well.
B: IP is not available. Reset the valid IP.
C: Web port number has been revised: contact administrator to get the correct port
number.
D: Exclude the above reasons. Recover default setting by long pressing the default hole.
Note: Default IP: 192.168.226.201,mask number: 255.255.255.0
3. Q:IP tool cannot search devices, why?
A:It may be caused by the anti-virus software in your computer. Please exit it and try to
search device again.
4. Q:IE cannot download ActiveX control. How can I do?
a. IE browser blocks ActiveX. Please do setup following below.
① Open IE browser. Click Tools-----Internet Options….
②
③
Select Security------Custom Level….Refer to Fig 4-1
Enable all the sub options under “ActiveX controls and plug-ins”. Refer to Fig 4-2
Page 40
IP CAMERA USER MANUAL
Fig 4-1
Fig 4-2
④
then click ok to finish setup.
b. Other plug-ins or anti-virus blocks ActiveX. Please uninstall or close them.
5. Q:No sound can be heard, why?
A:Without connect audio input device. Please connect and try again.
B: Without enable audio function at the corresponding channel. Please check AUDIO
item to enable this function.
6. Q:Why doesn’t the device connect to wireless?
A: Check the statues of wireless router. Please make sure the router is open
B: Check the router and the device port. Please make the router setup is matched with
device port.
7. Q: How to do when the device is unable to start normally on upgrading?
If the device is unable to start normally when upgrading, please rename the files
suffixed with .tar as updatepack.tar and copy it to the root directory of SD card. Restart
the device and then the device will upgrade automatically from the SD card. After
finishing upgrading, the user can search the IP address of IP Cam in the IP Tool.