SRTZ2610/SRTZ2610F/LRTZ2610
115 34 09-10 (001)
G
B
OWNER’S MANUAL
SHORT REACH TRIMMER
LONG REACH TRIMMER
SRTZ2610
SRTZ2610F
LRTZ2610
Original Language
GB-1
SRTZ2610/SRTZ2610F/LRTZ2610
EC DECLARATION OF CONFORMITY
(Applies to Europe only)
The undersigned manufacturer,
Husqvarna Zenoah Co.,Ltd.,
1-9, Minamidai, Kawagoe, Saitama, Japan,
declares under sole responsibility that the following products referred to in this
declaration conform with the requirement of the following COUNCIL’S DIRECTIVE.
The products referred to are :
DESIGNATION
MANUFACTURER
MODELS
SERIAL NUMBERS DATING
: SHORT REACH TRIMMERS/LONG REACH TRIMMERS
: Husqvarna Zenoah Co., Ltd.
: SRTZ2610/SRTZ2610F/LRTZ2610
: 2010 and onwards
(The year is clearly stated on the rating plate,
followed by the serial number)
This declaration conform with :
・DIRECTIVE 2006/42/EC
(The following standards have been applied: ISO 12100-1,-2, FprEN 15503: 2009)
・DIRECTIVE 2004/108/EC
(The following standards have been applied: EN 61000-6-1, EN 55012 (CISPR 12: 2005))
・DIRECTIVE 2000/14/EC
conformity assessment procedure followed ANNEX V
(The following standards have been applied: ISO 11094)
・DIRECTIVE 2002/88/EC
・ENISO 10517
Date :
29 December 2009
Signature :
Kiyoshi Honda
General Manager, Development Center
Authorised representative :
Husqvarna AB
SE-561 82 Huskvarna, Sweden
Person authorised to compile the technical file :
Bo R Jonsson
SE-561 82 Huskvarna, Sweden
GB-2
SRTZ2610/SRTZ2610F/LRTZ2610
EXPLANATION OF SYMBOLS AND SAFETY WARNINGS
G
B
WARNING!!!
RISK OF DAMAGING HEARING
Wear head, eye and ear protection.
MODEL
SOUND LEVEL1)
ISO 11094
ISO 10517
LpAeq
SRTZ2610
SRTZ2610F
LRTZ2610
25.4 cm3
25.4 cm3
25.4 cm3
95 dB(A)
93 dB(A)
99 dB(A)
LwA
guaranteed
110 dB(A)
110 dB(A)
110 dB(A)
VIBRATION LEVEL2)
ISO 22867
ahv, eq
6.6 m/s2
11.1 m/s2
5.5 m/s2
* Specifications are subject to change without notice
1) Noise emissions in the environment measured as sound power (LWA) in conformity with EC directive 2000/14/EC.
Reported soundpower level for the machine has been measured with the original cutting attachment that gives the highest level.
The difference between guaranteed and measured sound power is that the guaranteed sound power also includes
dispersion in the measurement result and the variations between different machines of the same model according to
Directive 2000/14/EC.
Reported data for equivalent sound pressure level (LpAeq) at the operator’s ear for the machine has a typical statistical
dispersion (standard deviation) of 1 dB (A).
2) Reported data for equivalent vibration level (ahv,eq) at the control handle has a typical statistical dispersion (standard deviation) of 1 m/s2.
APPROVAL NUMBER OF CE EXHAUST EMISSION REGULATION
DIRECTIVE 97/68/EC AMENDED 2002/88/EC
e13*97/68SH2G3*2002/88*0404*00
GB-3
SRTZ2610/SRTZ2610F/LRTZ2610
SAFETY FIRST
Instructions contained in warnings within this manual marked
with a
symbol concern critical points which must be taken
into consideration to prevent possible serious bodily injury, and
for this reason you are requested to read all such instructions
carefully and follow them without fail.
Contents
WARNINGS IN THE MANUAL
WARNING
This mark indicates instructions, which must be followed in order to prevent accidents, which could lead to serious bodily injury or death.
IMPORTANT
This mark indicates instructions, which must be followed, or it
leads to mechanical failure, breakdown, or damage.
NOTE
This mark indicates hints or directions useful in the use of the
product.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
Parts location .................................................. 3
Specifications ................................................. 4
Warning labels on the machine ...................... 4
Symbols on the machine ................................ 4
For safe operation ........................................... 5
Set up ............................................................. 8
Fuel ................................................................. 9
Operation ...................................................... 10
Maintenance ................................................. 12
Storage ......................................................... 14
Disposal ........................................................ 14
Troubleshooting guide .................................. 15
Information
This machine is equipped with an Overload Cancellation Mechanism.
When the cutting blades have got into metal wires or twigs difficult to cut, the mechanism works as a shock absorber,
and protects the gears and the blades from severe reaction which could give damage to those parts.
When the blades are frequently caught by twigs, please check the following points:
1. Size of the twigs --> Never try to cut twigs thicker than 5 mm.
2. Condition of the blade edges --> Replace the worn-out blades.
Thank you for choosing our product.
1. Parts location
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
(10)
(11)
(12)
(13)
(14)
(15)
GB-4
Loop handle
Suspension point
Stop switch
Throttle cable
Throttle trigger
Throttle set button
Shaft tube
Spark arrester
Starter knob
Fuel tank
Primer
Choke lever
Air cleaner cover
Blade
Transmission
13
12
8
11
10
9
(SRTZ2610)
(SRTZ2610F)
(LRTZ2610)
SRTZ2610/SRTZ2610F/LRTZ2610
2. Specification
LRTZ2610
SRTZ2610
SRTZ2610F
2300 x 400 x 365
1725 x 400 x 365
1734 x 338 x 254
6.6
6.4
6.5
Air-cooled 2-stroke gasoline
Zenoah GZ25N
rpm
1.2Hp (0.9kW) at 7500min-1
rpm
3000±200min-1
cm3
25.4
Mixture (Gasoline 50 : Oil 1) (when using ZENOAH genuine oil)
Walbro Diaphragm type
NGK CMR7H
L
0.65
Centrifugal clutch, Spiral bevel gear, Cam crank
4.25
4.0
4.0
Specifications are subject to change without notice.
Model
Overall size (LxWxH)
Dry weight *
Engine
Type
Model
Max output
Idle speed
Displacement
Fuel
Carburetor
Spark plug
Fuel tank capacity
Transmission
Reduction ratio
mm
kg
* Harness and protective cover are not included.
3. Warning labels on
the machine
(1) Warning / Attention
(2) Read owner’s manual before operating this machine.
4. Symbols on
the machine
For safe operation and maintenance, symbols are carved
in relief on the machine. According to these indications,
please be careful not to make a mistake.
The port to refuel the “MIX GASOLINE”
Position: FUEL TANK CAP
The direction to close the choke
Position: ENGINE COVER
(3) Wear head, eye and ear protection.
The direction to open the choke
Position: ENGINE COVER
(4) Keep hands away from
cutting blades.
If warning label peels off or becomes soiled and
impossible to read, you should contact the
dealer from which you purchased the product
to order new labels and affix them in the required
location(s).
Never modify your machine.
We won’t warrant the machine, if you use the
remodeled trimmer or if you don’t observe
the proper usage written in the manual.
GB-5
G
B
SRTZ2610/SRTZ2610F/LRTZ2610
5. For safe operation
1. Read this manual carefully until
you completely understand and
follow all safety and operating
instructions.
2. Keep this manual handy so that
you may refer to it later whenever any questions arise. Also
note, if you have any questions
which cannot be answered
herein, contact the dealer from
whom you purchased the product.
3. Always be sure to include this
manual when selling, lending, or
otherwise transferring the ownership of this product.
4. Never allow children or anyone
unable to fully understand the
directions given in the manual
to use the machine.
WORKING CONDITION
1. When using the product, you
should wear proper clothing and
protective equipment.
(1) Helmet
(2) Ear protectors
(3) Protection goggles or face
protector
(4) Thick work gloves
(5) Non-slip-sole work boots
2. And you should carry with you.
(1) Attached tools
(2) Properly reserved fuel
(3) Spare blade
(4) Things to notify your working
area (rope, warning signs)
(5) Whistle (for collaboration or
emergency)
(6) Hatchet or saw (for removal of
obstacles)
3. Do not wear loose clothing, jewelry, short trousers, sandals, or go
barefoot. Do not wear anything
which might be caught by a moving part of the unit. Secure hair
so it is above shoulder length.
GB-6
WORKING CIRCUMSTANCE
1. Never start the engine inside a
closed room or building. Exhaust
gases contain dangerous carbon
monoxide.
2. Never use the product,
a. when the ground is slippery
or when you can’t maintain a
steady posture.
b. At night, at times of heavy fog,
or at any other times when
your field of vision might be
limited and it would be difficult to gain a clear view of the
working area.
c. During rain storms, during
lightning storms, at times of
strong or gale-force winds, or
at any other times when
weather conditions might
make it unsafe to use the
product.
WORKING PLAN
1. You should never use the product when under the influence of
alcohol, when suffering from exhaustion or lack of sleep, when
suffering from drowsiness as a result of having taken cold medicine
or at any other time when a possibility exists that your judgment
might be impaired or that you
might not be able to operate the
product properly and in a safe
manner.
2. When planning your work schedule, allow plenty of time to rest.
Limit the amount of time over
which the product is to be used
continuously to somewhere
around 30 ~ 40 minutes per session, and take 10 ~ 20 minutes of
rest between work sessions. Also
try to keep the total amount of
work performed in a single day
under 2 hours or less.
WARNING
1. If you don’t observe the working
time, or working manner (See
“USING THE PRODUCT”), Repetitive Stress Injury (RSI) could
occur.
If you feel discomfort, redness and
swelling of your fingers or any
other part of your body, see a doctor before getting worse.
2. To avoid noise complaints, in general, operate product between
8 a.m. and 5 p.m. on weekdays
and 9 a.m. to 5 p.m. on weekends.
NOTE
Check and follow the local regulations as to sound level and hours of
operations for the product.
SRTZ2610/SRTZ2610F/LRTZ2610
5. For safe operation
BEFORE STARTING
THE ENGINE
1. The area within a perimeter of
15 m (50 ft) of the person using
the product should be considered
a hazardous area into which no
one should enter. If necessary,
yellow warning rope, warning
signs should be placed around
the perimeter of the area. When
work is to be performed simultaneously by two or more persons,
care should also be taken to constantly look around or otherwise
check for the presence and locations of other people working so
as to maintain a distance between
each person sufficient to ensure
safety.
2. Check the condition of working
area to avoid any accident by hitting hidden obstacles such as
stumps, stones, cans, or broken
glass.
IMPORTANT
Remove any obstacle before beginning work.
3. Inspect the entire unit for loose
fasteners and fuel leakage. Make
sure that the cutting attachment
is properly installed and securely
fastened.
4. Always use the harness. Adjust
the harness for comfort before
starting the engine. The harness
should be adjusted so the left
hand can comfortably hold the
handlebar grip approximately
waist high.
STARTING THE ENGINE
1. Keep bystanders and animals at
least 15 m (50 ft) away from the
operating point. If you are approached, immediately stop the
engine.
2. The product is equipped with a
centrifugal clutch mechanism, so
the cutting attachment begins to
rotate as soon as the engine is
started by putting the throttle trigger into the start position. When
starting the engine, place the
product onto the ground in a flat
clear area and hold it firmly in
place so as to ensure that neither
the cutting attachment nor the
throttle trigger come into contact
with any obstacle when the engine starts.
WARNING
Never place the throttle trigger
into the high-speed position when
starting the engine.
3. After starting the engine, check
to make sure that the cutting attachment stops rotating when the
throttle is moved fully back to its
original position. If it continues to
rotate even after the throttle trigger has been moved fully back,
turn off the engine and take the
unit to your authorized ZENOAH
servicing dealer for repair.
USING THE PRODUCT
IMPORTANT
Cut only materials recommended by
the manufacturer. And use only for
tasks explained in the manual.
1. Grip the handles firmly with both
hands using your whole hand.
Place your feet slightly apart
(slightly further apart than the
width of your shoulders) so that
your weight is distributed evenly
across both legs, and always be
sure to maintain a steady, even
posture while working.
2. Maintain the speed of the engine
at the level required to perform
cutting work, and never raise the
speed of the engine above the
level necessary.
3. If the unit starts to shake or vibrate, turn off the engine and
check the whole unit. Do not use
it until the trouble has been properly corrected.
4. Keep all parts of your body away
from moving cutting attachment
and hot surfaces.
5. Never touch the muffler, spark
plug, or other metallic parts of the
engine while the engine is in operation or immediately after shutting down the engine. Doing so
could result in serious burns or
electrical shock.
GB-7
G
B
SRTZ2610/SRTZ2610F/LRTZ2610
5. For safe operation
• IF SOMEONE COMES
1. Guard against hazardous situations at all times. Warn adults to
keep pets and children away from
the area. Be careful if you are approached. Injury may result from
flying debris.
2. If someone calls out or otherwise
interrupts you while working, always be sure to turn off the engine before turning around.
MAINTENANCE
1. In order to maintain your product
in proper working order, perform
the maintenance and checking
operations described in the
manual at regular intervals.
2. Always be sure to turn off the engine before performing any maintenance or checking procedures.
WARNING
The metallic parts reach high temperatures immediately after stopping the engine.
3. When replacing the cutting attachment or any other part, or
when replacing the oil or any lubricant, always be sure to use
only ZENOAH products or
products which have been certified by ZENOAH for use with
the ZENOAH product.
4. In the event that any part must be
replaced or any maintenance or
repair work not described in this
manual must be performed,
please contact a representative
from the store nearest ZENOAH
authorized servicing dealer for
assistance.
5. Do not use any accessory or attachment other than those bearing the ZENOAH mark and recommended for the unit.
6. Under no circumstances should
you ever take apart the product
or alter it in any way. Doing so
might result in the product becoming damaged during operation or the product becoming unable to operate properly.
GB-8
HANDLING FUEL
1. The engine of the ZENOAH product is designed to run on a mixed
fuel, which contains highly flammable gasoline. Never store cans
of fuel or refill the tank of the unit
in any place where there is a
boiler, stove, wood fire, electrical
sparks, welding sparks, or any
other source of heat or fire which
might ignite the fuel.
2. Never smoke while operating the
unit or refilling its fuel tank.
3. When refilling the tank, always
turn off the engine and allow it to
cool down. Take a careful look
around to make sure that there are
no sparks or open flames anywhere nearby before refueling.
4. Wipe spilled fuel completely using a dry rag if any fuel spillage
occurs during refueling.
5. After refueling, screw the fuel cap
back tightly onto the fuel tank and
then carry the unit to a spot 3 m
or more away from where it was
refueled before turning on the engine.
TRANSPORTATION
1. When hand-carrying the product,
cover over the cutting attachment
if necessary, lift up the product
and carry it paying attention to the
cutting attachment.
2. Never transport the product over
rough roads over long distances
by vehicle without removing all
fuel from the fuel tank. If doing so,
fuel might leak from the tank during transport.
SRTZ2610/SRTZ2610F/LRTZ2610
6. Set up
A Package contains the items as illustrated.
G
B
1
SRTZ2610
SRTZ2610F
2
3
LRTZ2610
4
5
6
7
9
SRTZ2610
8
SRTZ2610F
LRTZ2610
13
10
(1)
(2)
(3)
(4)
(5)
(6)
(7)
11
Shaft tube (SRTZ2610/SRTZ2610F)
Shaft tube (LRTZ2610)
Engine unit
Handle
Bolt
Cutting device (SRTZ2610)
Cutting device (SRTZ2610F)
14
12
(8)
(9)
(10)
(11)
(12)
(13)
(14)
Cutting device (LRTZ2610)
Harness
Hexagon socket (S16/S19) with torx driver (T-27)
Wrench
Spanner
Screw driver
Owner's manual
GB-9
SRTZ2610/SRTZ2610F/LRTZ2610
6. Set up
MOUNTING ENGINE
1. Push the shaft tube toward the clutch housing and move
it by hand to check that the power transmission shaft is
engaged with the gears.
2. Insert the shaft tube into the clutch housing until it bottoms, and align the positioning holes on the clutch housing and the shaft tube and install the screw. When difficult to engage, twist the engine slightly.
3. Fasten the clamp securely with two screws.
ATTACHING THE TRIMMING MECHANISM
1. Remove the screw screwed into the end of the transmission.
2. Insert the end of the tube into the transmission.
3. Line up the hole on the end of the transmission into
which the screw is to be inserted with the screw hole
on the tube, and screw the screw firmly in.
4. Using a wrench, screw the bolt provided to fix the
transmission into place.
Bolt
(1) Tube
(2) Transmission
(3) Screw hole
(4) Screw
(5) Fastening bolt
WARNING
Never use any screws other than those specified by the
manufacturer, or the engine can get loose, resulting in a
hazardous event.
IMPORTANT
Tighten the screws gradually by turns.
HARNESS
WARNING
CONNECTING THROTTLE WIRE
1. Remove the air cleaner cover.
2. Connect the end of the throttle wire to the joint on the top
of the carburetor.
M3 screw
Adjuster
ALWAYS WEAR THE PROVIDED HARNESS WHEN
USING THE MACHINE!
Always make sure the machine is hooked securely
to the harness.
If you don't, you will be unable to control the machine
safely. This can result in injury to yourself or others.
Never use a harness with a defective quick release
or any other damage.
HOW TO WEAR
1. Wear the provided harness without twisted bands, with
the hanger on your right side.
Insert the cable
to the end of
adjuster
Full on stopper
idle speed adjuster
1. Connect throttle wire with carburetor. Insert the cable to
the end of adjuster fix the throttle cable by tightening M3
screw. (Tightening torque: 0.4 ~ 0.8 N.m.)
2. Make sure the ‘STOPPER-PLATE’ of carburetor moves to
contact with ‘IDLE SPEED ADJUSTER’ and the ‘SWINGARM’ of carburetor moves to contact with ‘FULL ON
STOPPER’ by gripping throttle trigger.
CONNECTING SWITCH WIRES
• Connect the switch wires between the engine and the
main unit. Pair the wires of the same color.
QUICK RELEASE
The harness is equipped with a “QUICK RELEASE”devise.
To release the machine from the harness in emergency
situations, please follow the procedure as explained
below.
suspension point
Make sure to check proper working of the QUICK RELEASE device BEFORE operating the machine.
Make sure to hold the unit securely when using the
QUICK RELEASE.
arrow mark
While holding the unit by your
left hand securely, press both
sides of the buckle.
(1) Buckle
INSTALLING HANDLE
NOTE
The handle is put during the arrow mark.
GB-10
(1)
WARNING
SUSPENSION POINT
NOTE
Be the suspension point in the
location of the arrow mark.
• Mount the handle to
the shaft tube and
suspension point it at
a location that is
comfortable to you.
(1) Hanger
MIN CING
SPA
About 19 inches (48 cm)
(1)
BALANCE UNIT
1. Put on harness and attach unit to harness
2. Depending on the working posture, slide clamp up or
down until unit balances and the harness fits your
body.
SRTZ2610/SRTZ2610F/LRTZ2610
7. Fuel
■ FUEL
WARNING
• Gasoline is very flammable. Avoid smoking or
bringing any flame or sparks near fuel. Make sure
to stop the engine and allow it cool before refueling the unit. Select outdoor bare ground for fueling and move at least 3 m (10 ft) away from the
fueling point before starting the engine.
• The Zenoah engines are lubricated by oil specially
formulated for air-cooled 2-cycle gasoline engine use.
If Zenoah oil is not available, use an anti-oxidant added
quality oil expressly labeled for air-cooled 2-cycle
engine use (JASO FC GRADE OIL or ISO EGC
GRADE).
• Do not use BIA or TCW (2-stroke water-cooling type)
mixed oil.
■ RECOMMENDED MIXING RATIO
GASOLINE 50 : OIL 1
(when using ZENOAH genuine oil)
• Exhaust emission are controlled by the fundamental engine parameters and components (eq.,
carburation, ignition timing and port timing) without addition of any major hardware or the introduction of an inert material during combustion.
• These engines are certified to operate on unleaded
gasoline.
• Make sure to use gasoline with a minimum octane
number of 89RON (USA/Canada: 87AL).
• If you use a gasoline of a lower octane value than
prescribed, there is a danger that the engine temperature may rise and an engine problem such as
piston seizing may consequently occur.
• Unleaded gasoline is recommended to reduce the
contamination of the air for the sake of your health
and the environment.
• Poor quality gasolines or oils may damage sealing
rings, fuel lines or fuel tank of the engine.
■ HOW TO MIX FUEL
3. Pour in all of the oil and agitate well.
4. Pour in the rest of gasoline and agitate again for at
least one minute. As some oils may be difficult to
agitate depending on oil ingredients, sufficient agitation is necessary for the engine to last long. Be
careful that, if the agitation is insufficient, there is an
increased danger of early piston seizing due to abnormally lean mixture.
5. Put a clear indication on the outside of the container
to avoid mixing up with gasoline or other containers.
6. Indicate the contents on outside of container for easy
identification.
■ FUELING THE UNIT
1. Untwist and remove the fuel cap. Rest the cap on a
dustless place.
2. Put fuel into the fuel tank to 80% of the full capacity.
3. Fasten the fuel cap securely and wipe up any fuel
spillage around the unit.
WARNING
1. Select bare ground for fueling.
2. Move at least 10 feet (3 meters) away from the fueling point before starting the engine.
3. Stop the engine before refueling the unit. At that
time, be sure to sufficiently agitate the mixed gasoline in the container.
■ FOR YOUR ENGINE LIFE, AVOID:
1. FUEL WITH NO OIL (RAW GASOLINE) – It will cause
severe damage to the internal engine parts very
quickly.
2. GASOHOL – It can cause deterioration of rubber and/
or plastic parts and disruption of engine lubrication.
3. OIL FOR 4-CYCLE ENGINE USE – It can cause spark
plug fouling, exhaust port blocking, or piston ring
sticking.
4. Mixed fuels which have been left unused for a period of one month or more may clog the carburetor
and result in the engine failing to operate properly.
5. In the case of storing the product for a long period of
time, clean the fuel tank after rendering it empty. Next,
activate the engine and empty the carburetor of the
composite fuel.
6. In the case of scrapping the used mixed oil container,
scrap it only at an authorized repository site.
NOTE
As for details of quality assurance, read the description
in the section Limited Warranty carefully. Moreover, normal wear and change in product with no functional influence are not covered by the warranty. Also, be careful
that, if the usage in the instruction manual is not observed
as to the mixed gasoline, etc. described therein, it may
not be covered by the warranty.
IMPORTANT
Pay attention to agitation.
1. Measure out the quantities of gasoline and oil to be
mixed.
2. Put some of the gasoline into a clean, approved fuel
container.
GB-11
G
B
SRTZ2610/SRTZ2610F/LRTZ2610
8. Operation
IMPORTANT
STARTING ENGINE
Avoid pulling the rope to its end or returning it by releasing the knob. Such actions can cause starter failures.
WARNING
The cutting head will start moving upon the engine
starts.
1. Rest the unit on a flat, firm place. Keep the cutting
head off the ground and clear of surrounding objects
as it will start moving upon starting of the engine.
2. Push the primer several times until overflown fuel flows
out in the clear tube.
6. Move the choke lever downward to open the choke.
And restart the engine.
7. Allow the engine to warm up for a several minutes
before starting operation.
NOTE
1. When restarting the engine immediately after stopping it, leave the choke open.
2. Overchoking can make the engine hard to start due
to excess fuel. When the engine failed to start after
several attempts, open the choke and repeat pulling
the rope, or remove the spark plug and dry it.
3. Move the choke lever to the closed position.
choke lever
close
open
STOPPING ENGINE
1. Release the throttle trigger and run the engine for a
half minute.
2. Shift the stop switch to the “Stop” position.
IMPORTANT
Except for an emergency, avoid stopping the engine
while pulling the throttle trigger.
IMPORTANT
4. Set the stop switch to the “RUN” position. While pulling the throttle trigger(1,2), push the throttle set button(3), and release the throttle trigger(2), then the
throttle trigger is in to the “start position”.
(A) Run
(B) Stop
(C) stop switch
5. While holding the unit firmly, pull out the starter rope
quickly until engine fires.
When it doesn’t stop at the stop switch, move the choke
lever to the closed position.
ADJUSTING THROTTLE CABLE
The normal play is 1 or 2 mm when measured at the
carburetor side end. Readjust with the cable adjuster as
required and tighten the screw up.
(3)
(2)
(1)
GB-12
(1) Cable adjuster
(2) 0.04in (1~2mm)
(3) Screw
SRTZ2610/SRTZ2610F/LRTZ2610
8. Operation
ADJUSTING IDLING SPEED
1. When the engine tends to stop frequently at idling
mode, turn the adjusting screw clockwise.
2. When the cutting head keeps rotating after releasing
the throttle trigger, turn the adjusting screw counterclockwise.
resulting in injuries, scratches, and cuts, and for this
reason you should always be sure to wear a helmet
and face protector when using your trimmer.
G
B
NOTE
• The thickness of branches which may be cut using
this trimmer is limited to up to approximately 4.8mm.
Never try to cut branches thicker than this, as doing
so may result in damage to the trimmer.
(1) Idle speed adjuster
(1)
NOTE
Warm up the engine before adjusting the idling speed.
ADJUSTING THE MAXIMUM SPEED
• The screw at the throttle lever is for adjusting the maximum rpm.
• Turning the screw crock-wise, the rpm becomes down,
the otherwise, the rpm becomes up. (STANDARD OPERATION SPEED: 8000 to 9500 rpm)
Running engine with faster engine speed than 9500
rpm may damage the engine, slower engine speed
than 8000 rpm may cause of the poor cutting ability.
ADJUSTING THE ANGLE OF THE
CUTTING BLADES
1. Stop the trimmer engine.
2. Turn the bolt located on the top of the transmission
counter-clockwise to loosen it.
3. Adjust the angle of the blades to the desired angle,
and then fix the bolt firmly back into place.
(1) Clamp bolt
(2) Transmission
(3) Tighten
(4) Loosen
adjust screw
up
down
WARNING
• This product is equipped with extremely sharp blades,
and when used improperly these blades can be extremely dangerous, and improper handling can cause
accidents which may in turn lead to serious injury or
death. For this reason, you should always be careful
to follow the following instructions when using your
trimmer.
• Never hold the trimmer in a way in which the blades
are pointed towards someone else.
• Never allow the blades to come into proximity with
your body while the engine of the trimmer is in operation.
• Always be sure to turn off the engine before changing the angle of the blades, removing branches which
have become stuck in the blades, or at any other time
when coming into close proximity with the blades.
• Always wear work gloves made of leather or some
other sturdy material when using the trimmer.
• Always place the blade cover provided with the trimmer over the blades when not in use.
• Falling branches may fall onto the face or into the eyes,
GB-13
SRTZ2610/SRTZ2610F/LRTZ2610
9. Maintenance
System/components
ENGINE
fuel leaks, fuel spillage
fuel tank, air filter, fuel filter
idle speed adjuster
spark plug
SHAFT
intake air cooling vent
throttle trigger, stop switch
cutting attachment
transmission, cutter case
screws/nuts/bolts
MAINTENANCE CHART
Every Every Every
50
100
Before 25
Procedure
Note
use hours hours hours
after after after
wipe out
✔
inspect/clean
✔
✔
replace, if necessary
see adjusting
replace carburetor
✔
idling speed
if necessary
clean and readjust
GAP: .025 in (0.6 ~ 0.7 mm)
✔
plug gap
replace, if necessary
clean
✔
check operation
✔
replace if
✔
something’s wrong
grease
✔
tighten/replace
✔
✔ not adjusting screws
• Before cleaning, inspecting, or repairing the unit, make sure that the engine has stopped and is cool.
• Use protective gloves whenever inspecting, removing, sharpening, and installing the blades.
BLADES
• When refilling the tank or resting, it is often a good
idea to use the time to oil the cutting blades.
• If a gap exists between the upper and lower blades,
follow the procedure below to adjust them so that they
fit more closely together.
• Loosen lock nut (A) as shown in the diagram.
2. Tighten screw (B) fully, and then turn one-third to onehalf of a rotation backward.
3. While holding onto the screw to keep it in position,
tighten the lock nut.
4 .Check to make sure that the flat washer (C) is loose
enough so that it may be turned by pressing on it with
a finger.
(1) Upper blade
(2) Lower blade
QUICK TIP
• If the blades become so worn down that it is no longer
possible to eliminate the gap between them, you
should contact the authorized ZENOAH servicing
dealer from which you purchased your ZENOAH trimmer to have the blades resharpened or replaced.
TRANSMISSION
• The inside of the transmission should be lubricant using ZENOAH-approved lubricant after every 25 hours
of use.
• When adding lubricant, use a grease gun to insert
lubricant into the three grease nipples located on the
transmission.
TYPE OF LUBRICANT TO BE USED
Always be sure to use #2 lithium heat-resistant lubricant.
NOTE
• Screwing in the screw too tightly may make it impossible for the blades to move. Conversely, not screwing in the screw tightly enough may make the blades
of the trimmer feel dull and cause leaves and branches
to become caught in the blades of the trimmer.
GB-14
(1) Grease fitting
SRTZ2610/SRTZ2610F/LRTZ2610
9. Maintenance
WARNING
IMPORTANT
Make sure that the engine has stopped and is cool
before performing any service to the machine. Contact with moving cutting head or hot muffler may result in a personal injury.
AIR FILTER
• The air filter, if clogged, will reduce the engine performance. Check and clean the filter element in warm,
soapy water as required. Dry completely before installing. If the element is broken or shrunk, replace
with a new one.
• Note that using any spark plug other than those designated may result in the engine failing to operate
properly or in the engine becoming overheated and
damaged.
• To install the spark plug, first turn the plug until it is
finger tight, then tighten it a quarter turn more with a
socket wrench.
TIGHTENING TORQUE:
9.8 ~ 11.8 N.m.
(1 ~ 1.2 kg.m.)
MUFFLER
WARNING
Air Filter
FUEL FILTER
• When the engine runs short of fuel supply, check the
fuel cap and the fuel filter for blockage.
• Inspect periodically, the muffler for loose fasteners, any damage or corrosion. If any sign of exhaust leakage is found, stop using the machine
and have it repaired immediately in the repair specialty store.
• Note that failing to do so may result in the engine
catching on fire.
SPARK ARRESTER
• The muffler is equipped with a spark arrester to prevent red hot carbon from flying out of the exhaust outlet. Periodically inspect and clean as necessary with
a wire brush in the repair specialty store.
Fuel filter
SPARK PLUG
• Starting failure and mis-firing are often caused by a
fouled spark plug. Clean the spark plug and check
that the plug gap is in the correct range. For a replacement plug, use the correct type specified by
ZENOAH.
(1)
(1) Spark arrester
0.6 - 0.7 mm
• REPLACEMENT PLUG IS A NGK CMR7H.
GB-15
G
B
SRTZ2610/SRTZ2610F/LRTZ2610
9. Maintenance
10. Storage
INTAKE AIR COOLING VENT
• Aged fuel is one of major causes of engine starting
failure. Before storing the unit, empty the fuel tank and
run the engine until it uses all the fuel left in the fuel
line and the carburetor. Store the unit indoor taking
necessary measures for rust prevention.
• Oil the blades.
WARNING
• Check the intake air cooling vent after every 25
hours of use for blockage, and remove any waste
which has attached itself to the machine.
IMPORTANT
• If waste gets stuck and causes blockage around the
intake air cooling vent, it may cause the engine to
overheat, and that in turn may cause mechanical failure on the part of the machine.
11. Disposal
•
•
Intake air cooling vent
GB-16
When you dispose of the machine, do not disassemble the machine.
When you dispose of the machine, fuel, oil, be sure
to follow your local regulations.
SRTZ2610/SRTZ2610F/LRTZ2610
12. Troubleshooting guide
Case 1. Starting failure
CHECK
fuel tank
fuel filter
carburetor adjustment screw
sparking (no spark)
spark plug
→
→
→
→
→
→
PROBABLE CAUSES
incorrect fuel
fuel filter is clogged
out of normal range
spark plug is fouled/wet
plug gap is incorrect
disconnected
Case 2. Engine starts but does not keep running/hard re-starting
CHECK
PROBABLE CAUSES
fuel tank
→ incorrect fuel or staled fuel
carburetor adjustment screw → out of normal range
muffler, cylinder (exhaust port) → carbon is built-up
air cleaner
→ clogged with dust
cylinder fin, fan cover
→ clogged with dust
→
→
→
→
→
→
ACTION
drain it and use correct fuel
clean
adjust to normal range
clean/dry
correct (GAP: 0.6 ~ 0.7 mm)
retighten
→
→
→
→
→
ACTION
drain it and use correct fuel
adjust to normal range
consult with the repair specialty store
air blow or wash
consult with the repair specialty store
G
B
When your unit seems to need further service, please consult with our ZENOAH service shop in your area.
Limited warranty
Should any failure occur on the product under normal operating conditions within the applicable warranty period, the
failed part will be replaced or repaired free of charge by a
ZENOAH authorized dealer.
WARRANTY PERIOD: 1 year (6 months if used professionally, and 30 days if used for rental purpose) from the date of
initial purchase.
THE PURCHASER SHALL BEAR COSTS OF TRANSPORTING THE UNIT TO AND FROM THE ZENOAH DEALER.
THE PURCHASER SHALL NOT BE CHARGED FOR DIAGNOSTIC LABOR WHICH LEADS TO THE DETERMINATION
THAT A WARRANTED PART IS DEFECTIVE, IF THE DIAGNOSTIC WORK IS PERFORMED AT THE ZENOAH DEALER.
THE PURCHASER OR OWNER IS RESPONSIBLE FOR THE
PERFORMANCE OF THE REQUIRED MAINTENANCE AS
DEFINED BY THE MANUFACTURER IN THE OWNER/OPERATOR MANUAL.
NOT REDUCE THE WARRANTY OBLIGATION OF THE
COMPANY.
THE COMPANY IS LIABLE FOR DAMAGES TO OTHER
ENGINE COMPONENTS CAUSED BY THE FAILURE OF A
WARRANTED PART STILL UNDER WARRANTY.
THE WARRANTY DOES NOT APPLY TO THOSE UNITS
WHICH HAVE BEEN DAMAGED BY NEGLIGENCE OF INSTRUCTION LISTED IN THE OWNER/OPERATOR MANUAL
FOR PROPER USE AND MAINTENANCE OF THE UNITS
ACCIDENT MISHANDLING, ALTERATION, ABUSE, IMPROPER LUBRICATION, USE OF ANY PARTS OR ACCESSORIES OTHER THAN THOSE SPECIFIED BY THE COMPANY, OR OTHER CAUSES BEYOND THE COMPANY’S
CONTROL.
THIS WARRANTY DOES NOT COVER THOSE PARTS REPLACED BY NORMAL WEAR OR HARMLESS CHANGES
IN THEIR APPEARANCE.
THERE ARE NO OTHER EXPRESS WARRANTIES.
ANY WARRANTED PART WHICH IS NOT SCHEDULED FOR
REPLACEMENT AS REQUIRED MAINTENANCE, OR
WHICH IS SCHEDULED ONLY FOR REGULAR INSPECTION
TO THE EFFECT OF REPAIR OR “REPLACE AS NECESSARY” SHALL BE WARRANTED FOR THE WARRANTY PERIOD. ANY WARRANTED PART WHICH IS SCHEDULED
FOR REPLACEMENT AS REQUIRED MAINTENANCE
SHALL BE WARRANTED FOR THE PERIOD OF TIME UP
TO THE FIRST SCHEDULED REPLACEMENT POINT FOR
THE PART.
ANY REPLACEMENT PART THAT IS EQUIVALENT IN PERFORMANCE AND DURABILITY MAY BE USED IN NONWARRANTY MAINTENANCE OR REPAIRS, AND SHALL
IMPLIED WARRANTIES INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED TO TWO (2) YEARS OF HOME USE
[ONE (1) YEAR FOR ANY OTHER USE] FROM THE ORIGINAL DELIVERY DATE.
LIABILITIES FOR INCIDENTAL OR CONSEQUENTIAL
DAMAGE UNDER ANY AND ALL WARRANTIES ARE
EXCLUDED.
IF YOU NEED TO OBTAIN MORE INFORMATION, PLEASE
CALL YOUR NEAREST SERVICE CENTER, OR CHECK
PLEASE ZENOAH WEB SITE
http://www.zenoah.net
GB-17