Mitsubishi WD3300U User manual

DLP™ PROJECTOR
MODEL
WD3300U
User Manual
WD3300
This User Manual is important to you.
Please read it before using your projector.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert
the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure
that may be of sufficient magnitude to constitute a risk of electric shock.
The exclamation point within an equilateral triangle is intended to alert the user to the
presence of important operating and maintenance (servicing) instructions in the literature
accompanying the appliance.
WARNING:
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION:
TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD,
RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE
EXPOSURE.
NOTE:
SINCE THIS PROJECTOR IS PLUGGABLE EQUIPMENT, THE SOCKET-OUTLET SHALL BE INSTALLED NEAR
THE EQUIPMENT AND SHALL BE EASILY ACCESSIBLE.
WARNING
Use the attached specified power supply cord. If
you use another power supply cord, it may cause
interference with radio and television reception.
CAUTION
Not for use in a computer room as defined in the
Standard for the Protection of Electronic Computer/
Data Processing Equipment, ANSI/NFPA 75.
This apparatus must be grounded.
DO NOT LOOK DIRECTLY INTO THE LENS WHEN
THE PROJECTOR IS IN THE POWER ON MODE.
EN-2
Contents
Important safeguards.........................................................................................................................4
Preparing your projector.....................................................................................................................6
Using the remote control....................................................................................................................9
Setting up your projector..................................................................................................................10
Viewing computer images................................................................................................................13
Viewing video images.......................................................................................................................20
Menu operation................................................................................................................................25
Adjusting projected images..............................................................................................................33
Advanced features...........................................................................................................................37
Indicators..........................................................................................................................................41
Replacing the lamp..........................................................................................................................42
Maintenance.....................................................................................................................................44
Troubleshooting................................................................................................................................45
Specifications...................................................................................................................................49
Trademark, Registered trademark
• DLP™, Digital Micromirror Device, DMD and BrilliantColor™ are all trademarks of Texas Instruments.
• HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI
Licensing LLC.
• Macintosh is registered trademark of Apple Computer Inc.
• The trademark of PJLink is trademark applied for registration or registered trademark in Japan, the United States,
and other countries and areas.
• Other brand or product names are trademarks or registered trademarks of their respective holders.
EN-3
Important safeguards
Please read all these instructions regarding your
projector and retain them for future reference. Follow
all warnings and instructions marked on the projector.
10.Power sources
This projector should be operated only from the
type of power source indicated on the marking
label. If you are not sure of the type of power,
please consult your appliance dealer or local
power company.
11.Power-cord protection
Power-supply cords should be routed so that
they are not likely to be walked on or pinched
by items placed upon or against them. Pay
particular attention to cords at plugs, convenience
receptacles, and points where they exit from the
appliance. Do not put the power cord under a
carpet.
12.Overloading
Do not overload wall outlets and extension cords
as this can result in a fire or electric shock.
13.Objects and liquids
Never push objects of any kind through openings
of this projector as they may touch dangerous
voltage points or short-out parts that could result
in a fire or electric shock. Never spill liquid of any
kind on the projector.
14.Servicing
Do not attempt to service this projector by yourself.
Refer all servicing to qualified service personnel.
15.Damage requiring service
Unplug this projector from the wall outlet and refer
servicing to qualified service personnel under the
following conditions:
(a) If the power-supply cord or plug is damaged.
(b) If liquid has been spilled, or objects have fallen
into the projector.
(c) If the projector does not operate normally after
you follow the operating instructions. Adjust
only those controls that are covered by the
operating instructions. An improper adjustment
of other controls may result in damage and
may often require extensive work by a qualified
technician to restore the projector to its normal
operation.
(d) If the projector has been exposed to rain or
water.
(e) If the projector has been dropped or the
cabinet has been damaged.
(f) If the projector exhibits a distinct change in
performance - this indicates a need for service.
16.Replacement parts
When replacement parts are required, be sure
that the service technician has used replacement
parts specified by the manufacturer or parts
having the same characteristics as the original
part. Unauthorized substitutions may result in fire,
electric shock or other hazards.
17.Safety check
Upon completion of any service or repair to this
projector, ask the service technician to perform
safety checks determining that the projector is in a
safe operating condition.
1. Read instructions
All the safety and operating instructions should be
read before the appliance is operated.
2. Retain instructions
The safety and operating instructions should be
retained for future reference.
3. Warnings
All warnings on the appliance and in the operating
instructions should be adhered to.
4. Instructions
All operating instructions must be followed.
5. Cleaning
Unplug this projector from the wall outlet before
cleaning it. Do not use liquid aerosol cleaners. Use
a damp soft cloth for cleaning.
6. Attachments and equipment
Never add any attachments and/or equipment
without the approval of the manufacturer as such
additions may result in the risk of fire, electric
shock or other personal injury.
7. Water and moisture
Do not use this projector near water or in contact
with water.
8. Accessories
Do not place this projector on an unstable cart,
stand, tripod, bracket or table. Use only with a
cart, stand, tripod bracket, or table recommended
by the manufacturer or sold with the projector.
Any mounting of the appliance should follow
the manufacturer’s instructions and should use
a mounting accessory recommended by the
manufacturer.
An appliance and cart combination should be
moved with care. Quick stops, excessive force and
uneven surfaces may cause the appliance and cart
combination to overturn.
9. Ventilation
Slots and openings in the cabinet are provided
for ventilation, ensuring reliable operation of the
projector and to protect it from overheating. Do
not block these openings or allow them to be
blocked by placing the projector on a bed, sofa,
rug, or bookcase. Ensure that there is adequate
ventilation and that the manufacturer’s instructions
have been adhered to.
EN-4
Important safeguards (continued)
WARNING:
Do not insert your fingers in the space
between the lens and the cabinet.
Unplug immediately if there is something
wrong with your projector.
The lens may shift causing injury or damage to the
projector.
Do not operate if smoke, strange noise or odor comes
out of your projector. It might cause fire or electric
shock. In this case, unplug immediately and contact
your dealer.
Do not block the air inlet and outlet grilles.
If they are blocked, heat may be generated inside the
projector, causing deterioration in the projector quality
and fire.
Never remove the cabinet.
Do not use flammable solvents (benzene,
thinner, etc.) and flammable aerosols near the
projector.
This projector contains high voltage circuitry. An
inadvertent contact may result in an electric shock.
Except as specifically explained in the User Manual do
not attempt to service this product by yourself. Please
contact your dealer when you want to fix, adjust or
inspect the projector.
Flammable substances may ignite causing fire or
breakdown because the temperature inside the
projector rises very high while the lamp is illuminating.
Do not modify this equipment.
Do not use the projector with condensation on it.
It can lead to fire or electric shock.
It can lead to breakdown or other failure.
Do not keep using the damaged projector.
Place of installation
If the projector is dropped and the cabinet is
damaged, unplug the projector and contact your
dealer for inspection. It may lead to fire if you keep
using the damaged projector.
For safety’s sake, refrain from setting the projector
at any place subjected to high temperature and high
humidity. Please maintain an operating temperature,
humidity, and altitude as specified below.
• Operating temperature: between +41°F (+5°C) and
+95°F (+35°C)
• Operating humidity: between 30% and 90%
• Never put any heat-producing device under the
projector so that the projector does not overheat.
• Do not attach the projector to a place that is
unstable or subjected to vibration.
• Do not install the projector near any equipment that
produces a strong magnetic field. Also refrain from
installing near the projector any cable carrying a
large current.
• Place the projector on a solid, vibration free
surface; otherwise it may fall, causing serious injury
to a child or adult, and serious damage to the
product.
• Do not stand the projector; it may fall, causing
serious injury and damage to the projector.
• Slanting the projector more than ±10° (right and
left) or ±15° (front and rear) may cause trouble or
explosion of the lamp.
• Do not place the projector near air-conditioning
unit, heater, or humidifier to avoid hot or moist air
to the exhaust and ventilation hole of the projector.
Do not face the projector lens to the sun.
It can lead to fire.
Use correct voltage.
If you use incorrect voltage, it can lead to fire.
Do not place the projector on uneven surface.
Place the projection on a leveled and stable surface
only. Please do not place equipment on unstable
surfaces.
Do not look into the lens when it is operating.
It may hurt your eyes. Never let children look into the
lens when it is on.
Do not touch the air outlet grille and bottom
plate, which become hot.
Do not touch them or put other equipment in front
of the air outlet grille. The air outlet grille and bottom
plate, when heated, may cause injury or damage to
other equipment. Also, do not set the projector on the
desk which is easily affected by heat.
Do not look into the air outlet grille when
projector is operating.
Heat, dust, etc. may blow out of it and hurt your eyes.
EN-5
Preparing your projector
Checking accessories
The following accessories are provided with this projector. Check to be sure that all of the accessories are packed in
the package.
Cables
Power supply parts
Mini D-SUB
15-pin
D-SUB
9-pin
Mini D-SUB
15-pin
D-SUB
9-pin
RS-232C cable
(246C598-10)
RGB cable for PC
(246C597-10)
Power cord (two)
(246C483-10, 246C383-20)
• Used for projector control
by computer.
Others
Remote control parts
•
•
•
•
•
Lens cap (attached to the projector)
Terminal cover (750B017-10)
Lamp replacement tray (857C132-10)
CD-ROM (919C165-20)
Safety Manual/Quick Start up
(871D531-20)
R6 (size-AA)
battery (two)
Remote control
(290P176-20)
Important:
• The attached power cords are to be used exclusively for this product. Never use them for other products.
Inserting the batteries into the remote control
1
3
2
1. Remove the rear lid of the remote control.
2. Check the polarity (+), (-) of the batteries, and set them
correctly, inserting their (-) side first.
• If the battery is inserted from the (+) side first, inserting
the (-) side is difficult because the coil spring end hits
on the battery side. If the battery is forced to insert in
this way, the outer label of the battery may get ripped
and it may cause a short-circuit and heating.
3. Attach the rear lid.
Important:
• Use two size-AA batteries (R6).
• Replace the 2 batteries with new ones when the remote
control is slow to operate.
Removing the batteries from the remote control
Remove the back lid of the remote control and take out the
batteries.
Caution:
• Use of a battery of wrong type may cause explosion.
• Only Carbon-Zinc or Alkaline-Manganese Dioxide type batteries should be used.
• Dispose of used batteries according to your local regulations.
• Batteries may explode if misused. Do not recharge, disassemble, or dispose of them in fire.
• Be sure to handle the batteries according to the instructions.
• Load the batteries with its positive (+) and negative (-) sides correctly oriented as indicated on the remote control.
• Keep batteries out of reach of children and pets.
• Remove the batteries, if the remote control is not used for a long time.
• Do not combine a new battery with an old one.
• If the solution of batteries comes in contact with your skin or clothes, rinse with water. If the solution comes in
contact with your eyes, rinse them with water and then consult your doctor.
EN-6
Preparating your projector (continued)
Overview
1
3
4
2
5
7
6
9
8
1 Control area
2 Speaker
3 Air outlet grille
4 Lens
5 Remote control sensor (front)
6 Air inlet grille
7 Remote control sensor (rear)
8 Lamp cover
9 Terminal panel
10Air outlet grille
10
Caution:
Do not replace the lamp immediately after
using the projector because the lamp would
be extremely hot and it may cause burns.
Control area
1 POWER indicator
2 COMPUTER/DVI-D/ button
3 ZOOM/FOCUS button
4 STATUS indicator
5 POWER button
6 AUTO POSITION/ button
7 ENTER/KEYSTONE button
8 VIDEO/HDMI/ button
9 VOLUME/ button
10MENU button
11LENS SHIFT button
4
5
1
6
7
2
8
9
10
11
3
Terminal panel
1 2
3
4
56
1
2
3
4
7 8
5
6
7
8
9
10
1112
13
14 15
16 17 18 19
Power jack
Main power switch
O: OFF
I: ON
HDMI IN terminal (HDMI 19-pin)
COMPUTER/COMPONENT VIDEO DVI-D
IN (HDCP) terminal (DVI-D 24-pin)
AUDIO IN-1 terminal (mini jack)
AUDIO DVI-D terminal (mini jack)
DC OUT terminal (5V 1.5A MAX)
LAN terminal
20
9 Kensington Security Lock Standard connector
10Lock bar (SECURITY ANCHOR)
• Attach a chain, etc. to this lock bar to anchor the projector.
11COMPUTER/COMPONENT VIDEO IN-1 terminal (mini D-SUB 15-pin)
12COMPUTER/COMPONENT VIDEO IN-2 terminals (R/PR, G/Y, B/PB, H/HV, V) (BNC)
13MONITOR OUT terminal (mini D-SUB 15-pin)
14AUDIO OUT terminal (mini jack)
15AUDIO IN-2 terminal (mini jack)
16VIDEO IN and audio input terminals
17S-VIDEO IN and audio input terminals
18USB (COMPUTER) terminal
19REMOTE IN and OUT terminals
20SERIAL terminal (D-SUB 9-pin)
EN-7
Preparating your projector (continued)
Bottom side
1 Adjustment feet
1
Remote control
1 Laser aperture
2 Transmission window
3 Wired remote control jack
4 Indicator
5 HDMI button
6 POWER button
7 COMPUTER 1, 2 buttons
8 ZOOM/FOCUS button
9 LENS SHIFT button
10Mouse pointer
11PAGE UP and PAGE DOWN buttons
12MENU button
13HOME button
14END button
15ASPECT button
16CE (Color Enhancer) button
17KEYSTONE button
18AUTO POSITION button
19VIDEO button
20DVI-D(HDCP) button
21S-VIDEO button
22LASER button
23p, q, t, u buttons
24R-CLICK button
25ENTER button
26+ , - (VOLUME) buttons
27FREEZE button
28AV MUTE button
29Left click button
• Pressing the LASER button emits a laser beam.
Even when you keep holding down the LASER
button, it is emitted only one minute. To keep
emitting it longer, press the LASER button again.
• You can disable the LASER button to prevent
laser radiation due to misuse of the button.
How to disable the LASER button
While holding the LASER button down, press the
q button 3 times.
How to enable the LASER button
While holding the LASER button down, press the
p button 3 times.
• Whenever the batteries are replaced, the
LASER button is enabled.
1
3
2
4
5
6
29
KEYSTONE
COMPUTER
7
1
8
9
ZOOM/FOCUS
AUTO POSITION
HDMI
VIDEO
DVI-D(HDCP)
S-VIDEO
LENS SHIFT
LASER
2
22
23
10
11
12
13
14
15
16
17
18
19
20
21
R-CLICK
ENTER
HOME
PAGE UP
VOLUME
END
PAGE DOWN
MENU
24
25
26
ASPECT
CE
AV MUTE
FREEZE
27
28
About the laser beam
This remote control is a Class 2 laser product. (Max. output: 1 mW, Wavelength: 620-640 nm)
Beam Divergence: 6 m distance about 10.0 mm x 10.0 mm (±6.0 mm)
Caution:
• Pressing the LASER button on the remote control emits a laser beam. Do not look into the laser beam directly. Do
not point the laser beam at anyone. Looking at the laser beam directly may damage eyesight.
• Use of controls or adjustments or procedures other than those specified herein may result in hazardous radiation exposure.
• This remote controller cannot be repaired.
EN-8
Using the remote control
Operational range of the remote control
Rear of projector
Front of projector
30°
30°
30°
30°
Operate the remote
control within a distance
of 10 m (30 feet) from the
projector, pointing the
light beam at the remote
control photo-sensor (front
or rear) of the projector.
• Keep the remote control photo-sensor out of direct
sunlight or fluorescent lamp light.
• Keep the remote control photo-sensor at least 2 m
(6 feet) away from fluorescent lamps. Otherwise, the
remote control may malfunction.
• If there is an inverter-operated fluorescent lamp near
the remote control, the remote control operation may
become unstable.
• When you use the remote control too close to the
remote control sensor, the remote control may not work
correctly.
When operating the remote control, keep the
distance from the remote control to the projector
via the screen within about 5 m (15 feet). The
operable range of the remote control, however,
depends on the characteristics of the screen.
Reception angle
Vertical directions
20°
10°
20°
10°
Vertical directions (ceiling mount)
20°
20°
Using the wired remote control
Attached remote control for this projector can be used as a wired remote control with remote control cable. Wired
remote control is useful for operating in a distance or outside of the operating area.
• For connection, use the pin-pin cable of ø3.5 stereo
type, which is commercially available. However,
some cable may not work correctly.
• When REMOTE OUT terminal on this projector is
connected to the REMOTE IN terminal on the other
projector, the two projectors can be controlled
together by using the remote control.
• When the remote control is connected with remote
control cable, it does not work as a wireless remote
control.
• When using the wired remote control, the laser
beam may be darker. It is normal.
REMOTE IN
REMOTE IN
REMOTE OUT
EN-9
Setting up your projector
Setting up the screen
Install the screen perpendicularly to the projector. If the screen can not be installed in such a way, adjust the
projection angle of the projector. (See page 11.)
• Install the screen and projector so that the projector’s lens is placed at the same height and horizontal position of
the screen center.
• Do not install the screen where it is exposed to direct sunlight or lighting. Light directly reflecting on the screen
makes the projected images whitish and hard to view.
Screen size and projection distance
Refer to the following table to determine the screen size and projection distance.
• For the aspect ratio setting, see page 19.
• The figures in the tables are approximate and may be slightly different from the actual measurements.
• The lens shift height and width show distances from the factory default position.
Front projection
W
W1
Front projection, ceiling mounting
W1
W
W1
W1
H1
H2
Center of the lens
H1
H
H0
H0
H
Center of the lens
H2
L
L
L
L
Maximum projection area
Maximum projection area
When the aspect ratio is “FULL” (Display at 1280 x 800 pixels)
Size of the projected image (16:10)
Diagonal size
Width
(W)
Height
(H)
inch
40
cm
102
inch
34
cm
86
inch
21
60
152
51
129
32
80
203
68
172
42
100
254
85
215
53
150
381
127
323
200
508
170
250
635
300
762
cm
54
Projection distance (L)
Shortest
(Wide)
Longest
(Tele)
Lens shift height
Standard
(H0)
inch
58
m
1.5
inch
80
m
2.0
inch
2.3
81
88
2.2
121
3.1
108
118
3.0
162
4.1
135
148
3.8
203
79
202
224
5.7
431
106
269
299
212
538
132
337
254
646
159
404
Lens shift width
Movement
Movement
distance (H1) distance (H2)
cm
6
inch
cm
12
30
inch
2
3.4
9
18
46
4.6
12
24
61
5.2
5.7
15
30
306
7.8
8.6
22
7.6
408
10.4
11.4
375
9.5
-
-
450
11.4
-
-
Movement
distance (W1)
cm
6
inch
3
cm
9
3
9
5
13
4
11
7
17
76
6
14
9
22
45
114
8
21
13
33
29
60
152
11
28
17
44
14.3
36
36
21
55
44
191
229
14
17.2
75
90
17
43
26
65
When the aspect ratio is “NORMAL (FULL)” and 4:3 signal is displayed (Display at 1066 x 800 pixels)
Size of the projected image (4:3)
Diagonal size
Width
(W)
Height
(H)
inch
40
cm
102
inch
32
cm
81
inch
24
60
152
48
122
80
203
64
163
100
254
80
150
381
200
250
Projection distance (L)
Shortest
(Wide)
Longest
(Tele)
Lens shift height
Standard
(H0)
cm
61
inch
65
m
1.7
inch
90
m
2.3
inch
2.3
36
91
100
2.5
137
3.5
48
122
134
3.4
183
4.7
203
60
152
168
4.3
230
120
305
90
229
254
6.4
508
160
406
120
305
339
635
200
508
150
381
425
Lens shift width
Movement
Movement
distance (H1) distance (H2)
cm
6
inch
cm
12
30
inch
2
3.4
9
18
46
4.6
12
24
61
5.8
5.7
15
30
346
8.8
8.6
22
8.6
-
-
11.4
10.8
-
-
14.3
Movement
distance (W1)
cm
6
inch
3
cm
9
3
9
5
13
4
11
7
17
76
6
14
9
22
45
114
8
21
13
33
29
60
152
11
28
17
44
36
75
191
14
36
21
55
• Depending on the installation conditions, warm air that is emitted from the exhaust vents may flow into the intake
vent, causing the projector to display “TEMPERATURE!!” and then stop projecting images.
EN-10
Setting up your projector (continued)
Adjusting the position of the projected image
To adjust the positions of the projector and the screen, use LENS SHIFT button.
1. Press the LENS SHIFT button.
• The LENS SHIFT menu appears at the center of the screen.
LENS
SHIFT
2. Press the p, q, t or u button to move the image position.
• When the q button is pressed, the image moves down.
• When the p button is pressed, the image moves up.
• When the u button is pressed, the image moves to the right.
• When the t button is pressed, the image moves to the left.
• When the ENTER button is pressed while the LENS SHIFT menu is displayed, the shift mode can be switched
between FAST and STEP. When FAST is selected, the lens shifts in a large amount with the p, q, t or u button,
and it shifts in a small amount when STEP is selected.
• When the LENS SHIFT menu is displayed while no video signal is input to the projector, a crosshatch appears on
the entire screen.
• Be careful not to be caught in the opening in the lens while the lens is moving.
• While the lens shift is working, the screen may flicker.
FAST
SELECT:ENTER
Correcting skewed or distorted image
For the best projection, project images on a flat screen installed at 90 degrees to the floor. If necessary, tilt the
projector using the two adjustment feet on the bottom of the projector.
1. Tilt up the projector to the appropriate angle.
2. Rotate the adjustment feet for fine adjustment.
Important:
• Don’t transport the projector with its adjustment feet extended. Otherwise the
adjustment feet may be damaged.
Screen
When fine streaks are seen on projected images
Adjustment feet
This is due to interference with the screen surface and is not a malfunction. Replace the screen or displace the focus
a little. (See page 16 or 23 for focus adjustment.)
When projected images are distorted to a trapezoid
When the screen and the projector are not placed perpendicularly to each other, projected images become
trapezoidal. If you cannot make the projector and the screen perpendicular to each other by mechanical adjustments,
adjust keystone.
To adjust keystone:
Press the KEYSTONE button on the projector or the
remote control to display KEYSTONE, and adjust
the image by pressing the , ,  or  button (or
VOLUME + or - button on the remote control).
In the following cases (for front projection):
Press the 
button.
Press the 
button.
Press the 
(or -) button.
Press the 
(or +) button.
Important:
• For proper keystone adjustment results, reset the lens to the factory-adjusted position using LENS SHIFT RESET
in the INSTALLATION menu before carrying out keystone adjustment. (See page 30.)
• When the keystone adjustment is carried out, the adjustment value is indicated. Note that this value doesn’t mean
a projection angle.
• The allowable range of the adjustment value in the keystone adjustment varies depending on the installation
conditions.
• When the keystone adjustment takes effect, the resolution decreases. In addition, stripes may appear or straight
lines may bend in images with complicated patterns. They are not due to product malfunctions.
• When the keystone adjustment is performed, the displayed image may be distorted.
• Depending on the installation conditions of the projector and the screen, a perfect rectangular image and the
proper aspect ratio may not be obtained.
• Noise may appear on the screen during the keystone adjustment because of the type of the video signal being
projected and the setting values of the keystone adjustment. In such cases, set the keystone adjustment values in
the range where the image is displayed without noise.
• When horizontal and vertical keystone adjustments are performed in combination, the adjustable range becomes
narrower than in the case when they are performed separately.
• In the keystone adjustment with the option lens, the proper aspect ratio may not be obtained.
EN-11
Setting up your projector (continued)
Front projection, ceiling mounting
Rear projection
For ceiling mounting, you need the ceiling mount
kit designed for this projector. Ask a specialist for
installation. For details, consult your dealer.
• The warranty on this projector does not cover any
damage caused by use of any non-recommended
ceiling mount kit or installation of the ceiling mount
kit in an improper location.
Ask a specialist for installation. For details, consult
your dealer.
• For rear projection, set IMAGE REVERSE in the
INSTALLATION menu to MIRROR. See page 30.
Caution:
• Placing the projector directly on a carpet impairs
ventilation by the fans, causing damage or failure.
Put a hard board under the projector to facilitate
ventilation.
• Place the projector at least 50 cm (or 20 inches)
away from the wall to prevent the air inlet grille and
the air outlet grilles that emit hot air from being
blocked.
• Do not use the projector in the following locations
and manners, which may cause fire or electric
shock.
• In a dusty or humid place.
• In a sideways position, or with the lens facing
down.
• Near a heater.
• In an oily, smoky, or damp place such as a kitchen.
• In direct sunlight.
• Where the temperature rises high, such as in a
closed car.
• Where the temperature is lower than +41ºF (or
+5ºC) or higher than +95ºF (or +35ºC ).
• When using the projector mounted on the ceiling,
set IMAGE REVERSE in the INSTALLATION menu
to MIRROR INVERT. See page 30.
• When the projector is mounted on the ceiling,
images may appear darker than those projected in
the case of tabletop mounting. This isn’t a product
malfunction.
• Ask your installation specialist to provide a breaker.
When you do not use the projector, be sure to shut
down the main power by the breaker.
• Do not install the projector where the exhaust vents
are exposed to air emitted by an air conditioning.
Such installation may cause a breakdown.
• Do not install the projector near a fire alarm
because it emits hot air from its exhaust vents.
Important:
• We don’t recommend using the projector at an
altitude of 1500 meters or higher. Use at an altitude
of 1500 meters or higher may affect the projector’s
life.
EN-12
Viewing computer images
A. Connecting the projector to a computer
Preparation:
• Make sure that the power of the projector and that of the computer are turned off.
• When connecting the projector to a desktop computer, disconnect the RGB cable that is connected to the monitor.
Computer
COMPUTER/
COMPONENT
VIDEO IN-1
1
2
To monitor port
• When viewing images supplied from an analog-connected
computer, press the COMPUTER 1 button on the remote
control.
RGB cable
Computer
R/PR G/Y B/PB H/HV V
COMPUTER/
COMPONENT
VIDEO IN-2
1
To monitor
port (5 BNC)
2
V H/HV B/PB G/Y R/PR
BNC cable (option)
1
2
To DVI
DVI cable (option)
Computer
AUDIO IN-1/2
1
AUDIO OUT
PC audio cable
(option)
2
For analog connection:
(For using the COMPUTER/COMPONENT VIDEO IN-2
terminal.)
1. Connect one end of a commercially available BNC cable to
the COMPUTER/COMPONENT VIDEO IN-2 terminal of the
projector.
2. Connect the other end of the BNC cable to the 5 BNC
terminals of the monitor port of the computer.
• When viewing images supplied from an analog-connected
computer, press the COMPUTER 2 button on the remote
control.
For digital connection:
1. Connect one end of a commercially available DVI cable to
the COMPUTER/COMPONENT VIDEO DVI-D IN (HDCP)
terminal of the projector.
2. Connect the other end of the DVI cable to the DVI terminal
of the computer.
Computer
COMPUTER/
COMPONENT
VIDEO DVI-D IN
(HDCP)
For analog connection:
(For using the COMPUTER/COMPONENT VIDEO IN-1
terminal.)
1. Connect one end of the supplied RGB cable to the
COMPUTER/COMPONENT VIDEO IN-1 terminal of the
projector.
2. Connect the other end of the RGB cable to the monitor
port of the computer.
To audio output
terminal
• When viewing images supplied from a digital-connected
computer, press the DVI-D(HDCP) button on the remote
control.
• Turn on the main power switch of the projector before
starting the computer.
For audio connection:
1. Connect one end of a commercially available PC audio
cable to the AUDIO IN-1/2 terminal of the projector.
2. Connect the other end of the PC audio cable to the audio
output terminal of the computer.
• This projector uses stereo pin jack for its audio input.
Check the type of the audio output terminal of the
connected computer and prepare a proper cable for
connection. Some computers don’t have the audio output
terminal.
• Speaker output is mono.
• No audio is output from the projector’s speaker and the
AUDIO OUT terminal during power standby.
• Additional devices, such as a conversion connector and an analog RGB output adapter, are required depending
on the type of the computer to be connected.
• Use of a long cable may decrease the quality of projected images.
• Images may not be projected correctly, depending on the type of the connected computer.
• When DVI-D signal is input, some signal setting menus are unavailable.
• Also read the instruction manual of the equipment to be connected.
• Contact your dealer for details of connection.
EN-13
Viewing computer images (continued)
Monitor
1
For monitor connection:
1. Connect the RGB cable from the monitor to the MONITOR
OUT terminal of the projector.
• No video signal is output from the MONITOR OUT terminal
during power standby.
MONITOR OUT
RGB cable
To audio input
terminals
1
2
AUDIO OUT
For audio output connection:
1. Connect one end of a commercially available audio cable
to the AUDIO OUT terminal of the projector.
2. Connect the other end (white and red) of the audio cable to
the audio input terminals (L, R) of the audio equipment.
• When the audio cable is connected to the AUDIO OUT
terminal, the speaker output is muted.
Audio cable (option)
About DDC
The COMPUTER/COMPONENT VIDEO IN-1 terminal of this projector complies with the DDC1/2B standard and the
COMPUTER/COMPONENT VIDEO DVI-D IN (HDCP) terminal complies with the DDC2B standard. When a computer
supporting this standard is connected to this terminal, the computer will automatically load the information from this
projector and prepare for output of appropriate images.
• When connecting a DDC-supporting computer to the projector, turn on the main power switch of the projector
before starting the computer.
B. Plugging the power cord
• In order to ensure the safety in case of trouble with the projector, use an electrical outlet having an earth leakage
breaker to supply the power to the projector. If you do not have such outlet, ask your dealer to install it.
1. Plug the attached power cord into the power cord inlet of
this projector.
2. Plug the other end of the power cord into a power outlet.
Earthing
terminal
2
1
Power cord (example)
• The power cords for use in the U.S. and Europe are included with this projector. Use the appropriate one for your
country.
• This projector uses the power plug of 3-pin grounding type. Do not take away the grounding pin from the power
plug. If the power plug doesn’t fit your wall outlet, ask an electrician to change the wall outlet.
• The provided power cord for the U.S. is rated at 120 V. Never connect this cord to any outlet or power supply
using other voltages or frequencies than rated. If you use a power supply using other voltage than rated, prepare
an appropriate power cord separately.
• Use 100-240 V AC 50/60 Hz to prevent fire or electric shock.
• Do not place any objects on the power cord or do not place the projector near heat sources to prevent damage to
the power cord. If the power cord should be damaged, contact your dealer for replacement because it may cause
fire or electric shock.
• Do not modify or alter the power cord. If the power cord is modified or altered, it may cause fire or electric shock.
Caution:
• Plug in the power cord firmly. When unplugging, hold and pull the power plug, not the power cord.
• Do not plug in or out the power cord with your hand wet. It may cause electric shock.
EN-14
Viewing computer images (continued)
C. Installing the terminal cover
This projector includes a terminal cover. If necessary, install the terminal cover to the projector.
1. Fit two hooks of the terminal cover into the projector.
2. Tighten the attachment screws (a) firmly.
Important:
• Don’t carry the projector by the terminal cover.
(a)
EN-15
Viewing computer images (continued)
D. Projecting images
Preparation:
• Remove the lens cap.
Main power switch
POWER button
POWER indicator
STATUS indicator
POWER button
COMPUTER 1, 2 buttons
ENTER button
COMPUTER/
DVI-D button
ZOOM/FOCUS button
LENS SHIFT button
p, q, t, u buttons
DVI-D(HDCP)
button
p, q, t, u
buttons
ZOOM/FOCUS button
ENTER button
LENS SHIFT button
1. Put the projector into standby mode by pressing the main power switch. The POWER indicator lights up red.
• If the projector was turned off before the lamp was cooled down sufficiently last time, the fan may start rotating
and the POWER button may not work after the main power switch is turned ON. (The STATUS indicator blinks
green.) After the fan stops rotating, press the POWER button to turn back on the POWER indicator.
2. Turn on the power of the connected computer.
3. Press the POWER button.
• It may take about 1 minute for the lamp to light up.
• The lamp fails to light up on rare occasions. In such a case, wait for a few minutes and then try again.
• Do not cover the lens with the lens cap while the lamp is on. Do not strip off the aluminium sheet inside the
lens cap.
• After the POWER button is pressed, the image may flicker before the lamp becomes stable. This is not a
product malfunction.
• The lamp operation becomes stable in 1 minute after the power is turned on and then the lamp mode selected
in the menu is activated. During the activation, displayed images may be disturbed.
• The projector starts warming up when the POWER button is pressed. During the warm-up process, images
may appear dark and no commands are accepted.
• By blinking red, the STATUS indicator indicates that the lamp should be replaced soon. Replace the lamp when
the STATUS indicator blinks red. (See page 41.)
4. Press the ZOOM/FOCUS button to display the ZOOM/FOCUS menu.
5. Adjust with the  or  button to get a fine picture.
• When the ENTER button is pressed while the ZOOM/FOCUS menu is displayed, the adjustment mode is
switched between FAST and STEP. When FAST is selected, the speed of focus controlled by the  or  button
becomes fast, and it becomes slow when STEP is selected.
6. Select an input source.
• Press the COMPUTER/DVI-D button on the projector or the COMPUTER 1, COMPUTER 2 or DVI-D(HDCP)
button on the remote control that is corresponding to the terminal in use.
• The input source is switched from COMPUTER 1 to COMPUTER 2 to DVI at every press of the COMPUTER/
DVI-D button on the projector.
• The projector automatically selects the appropriate signal format. The selected signal format is displayed on
the screen.
• You cannot change the input source while the menu is being displayed.
• Though it may take some time before an image is displayed on the screen depending on the type of the input
signal, such symptom is not a malfunction.
• Images may not be projected in the correct position, depending on the type of the input signal. In such a case,
press the AUTO POSITION button. (See page 18.)
• When COMPUTER 1 or COMPUTER 2 is chosen as the source, images supplied from the computer may
flicker. Press the  or  button on the remote control to reduce flicker, if it occurs. (Fine adjustment)
7. Adjust the position of the projector to keep an appropriate projection distance with which images are projected in
their specified sizes.
8. Adjust the position of the projector so that the projector and the screen are perpendicular to each other. (See page 10.)
• When the projector cannot be positioned perpendicularly to the screen, adjust the projection angle. (See page 11.)
EN-16
Viewing computer images (continued)
9. Press the ZOOM/FOCUS button to display the ZOOM/FOCUS menu.
10.Adjust with the p or q button to get an approximate size.
• When the ENTER button is pressed while the ZOOM/FOCUS menu is displayed, the adjustment mode is
switched between FAST and STEP. When FAST is selected, the speed of zoom controlled by the p or q
button becomes fast, and it becomes slow when STEP is selected.
11.Press the LENS SHIFT button. The LENS SHIFT menu appears at the center of the screen.
12.Press the p or q button to adjust the vertical position and  or  button to adjust the horizontal position of the
displayed image.
• When the image is not displayed within the screen, adjust the projection angle. In addition, perform the
keystone adjustment, if necessary. (See page 11.)
Repeat steps 4, 5 and 9 to 12, if necessary.
Important:
• Focus, zoom and lens shift adjustment is possible in the normal picture mode only.
To stop projecting:
13.Press the POWER button.
• A confirmation message is displayed.
• To cancel the procedure, leave the projector for a while or press any button except the POWER button.
14.Press the POWER button again.
• The lamp goes out and the projector goes into a standby mode. In this standby mode, the STATUS indicator
blinks green.
15.Wait about 2 minutes for the STATUS indicator to be turned off.
• During this period of 2 minutes in the standby mode, the intake fan and exhaust fan rotate to cool the lamp.
• The air outlet fans rotate faster as the temperature around the projector rises.
• Though the fans make loud sounds during cooling, such symptom is not a malfunction.
16.Turn off the main power switch.
• The POWER indicator will go out.
• If the main power switch should be turned off or the power cord should be unplugged accidentally while either
the air inlet fan or the air outlet fans are operating or the lamp is on, allow the projector to cool down for 10
minutes with the power off. To light the lamp again, press the POWER button. If the lamp doesn’t light up
immediately, repeat pressing the POWER button 2 or 3 times. If it should still fail to light up, replace the lamp.
• Cover the lens with the lens cap to protect it from dust.
• For safety’s sake, unplug the power cord from the outlet.
• When you repeat turning off the main switch within 30 minutes from the lamp illumination, an error may occur
in the clock function of this product.
Instant Shut Down
You can turn off this projector just by turning off the power switch or unplugging the power cord without pressing the
POWER button.
• Don’t shut down the projector while the STATUS indicator is blinking after the lamp lights up because the lamp’s
life may be shortened.
• Don’t turn the projector back on right after shutting it down because the lamp's life may be shortened. (Wait about
10 minutes before turning the projector back on.)
• Before shutting down the projector, be sure to close the menu screen. If you shut down the projector without
closing the menu, the setting data of the menu may not be saved.
• If you shut down the projector while controlling the projector using the network function, the application software
such as ProjectorView may fail. For details, see “User Guide of LAN Control Utility” contained in the CD-ROM.
EN-17
Viewing computer images (continued)
AV mute
The video and audio signals are temporarily muted when the AV MUTE button is pressed. To cancel muting, press the
AV MUTE button again.
• It takes several seconds before muting is completely canceled.
• If AV MUTE MODE in the INSTALLATION menu is set to IMAGE, the splash screen will appear when the AV MUTE
button is pressed.
• You can alter the splash screen optionally. See page 37.
• The audio from the AUDIO OUT terminal is also muted by pressing the AV MUTE button.
AUTO POSITION button
When the image supplied from the computer is displaced, carry out the following procedure.
1. Project a bright image containing as many texts and characters as possible.
2. When the screen saver has been enabled, disable it.
3. Press the AUTO POSITION button. The projector automatically makes optimum positional settings for the input signal.
• If the projected image is still displaced even after pressing the AUTO POSITION button several times, refer to
the procedure to adjust computer images. (See pages 35 and 36.)
• When you carry out this procedure with a dark image, the image may be displaced.
When connecting to a notebook computer:
When the projector is connected to a notebook computer, images may not be projected in some cases. In such
cases, set the computer so that it can output signals externally. The setting procedure varies depending on the type
of the computer. See the instruction manual of your computer.
Example of the setting procedure for external output
Press the [Fn] key and any of the keys [F1] to [F12] at the same time. (The key to be pressed depends on the type of
the computer you use.)
Setting of the resolution
If the resolution of the computer doesn’t match with that of the projector, projected images may be obscured. Ensure
that their resolutions are the same (see page 50). For the method to change the output resolution of the computer,
contact the manufacturer of the computer.
EN-18
Viewing computer images (continued)
Setting the aspect ratio
You can change the aspect ratio of the input video signal (or the ratio of width to height of the image). Change the
setting according to the type of the screen to be used or your preference.
How to change the settings:
With the remote control:
1. Press the ASPECT button.
• Every time the ASPECT button is pressed, the aspect mode changes from NORMAL (FULL) to NORMAL (16:9),
to NORMAL (4:3), to 16:9, to REAL, to FULL, and back to NORMAL (FULL).
• The following table shows the image display patterns depending on the settings.
Setting
NORMAL (FULL)
Input video signal is
displayed at the max
height (800 pixels) or
max width (1280
pixels) of the panel
while its aspect ratio
is maintained.
NORMAL (16:9)
Select this setting
when using a 16:9
screen.
NORMAL (4:3)
Select this setting
when using a 4:3
screen.
Input signal
4:3 signal,
XGA signal
(1024 x 768),
etc.
WXGA signal
1280 x 800
(16:10)
WXGA signal
1280 x 768
(16:9.6)
WXGA signal
1360 x 768
(16:9.04)
16:9
REAL
FULL
Regardless of the type
of input signal, image
is displayed at 16:9
aspect ratio (1280 x
720 pixels). Select to
expand squeezed (or
horizontally
compressed) images
such as DVD images
to 16:9.
Input video signal is
displayed at its
original pixel size.
(When the pixel size is
larger than the panel
size, only the center
part of the image is
displayed.)
Regardless of the type
of input signal, image
is displayed at the full
panel size (1280 x 800
pixels).
4:3
4:3
4:3
16:9
4:3
16:10
1066 x 800
960 x 720
1066 x 800
1280 x 720
1024 x 768
1280 x 800
16:10
16:10
16:10
16:9
16:10
16:10
1280 x 800
1152 x 720
1066 x 666
1280 x 720
1280 x 800
1280 x 800
16:9.6
16:9.6
16:9.6
16:9
16:9.6
16:10
1280 x 768
1200 x 720
1066 x 640
1280 x 720
1280 x 768
1280 x 800
16:9.04
16:9.04
16:9.04
16:9
16:10
16:10
1280 x 720
1280 x 720
1066 x 602
1280 x 720
1280 x 800
(1360 x 768)
1280 x 800
QUICK MENU
16:9 signal
and
WXGA signal
1366 x 768
16:9
16:9
16:9
16:9
COLOR
ENHANCER
16:10
CONTRAST
1280 x 720
1280 x 720
1066 x 600
1280 x 720
1280
x 800
BRIGHTNESS
(1366 x 768)
COLOR TEMP.
AUTO
16:10
0
1280 x0 800
STANDARD
With the QUICK MENU or FEATURE menu:
0
SHARPNESS
(See page 26 for menu setting.)
LAMP MODE
STANDARD
1. Display the QUICK MENU or FEATURE menu.
ASPECT
NORMAL (FULL)
2. Select ASPECT by pressing the  or  button.
COLOR
0
SELECT
3. Select your desired aspect ratio by pressing the  or  button.
COLOR
USER MENU
OK
DETAIL MENU
When 16:9 is selected with the FEATURE menu, you can select whether or not
opt.
to display signals at 16:9 depending on their type using the following procedures.
FEATURE
4. Press the ENTER button.
ASPECT – 16:9
5. Select a setting for the item MODE by pressing the  or  button.
MODE
ALL SIGNAL
• ALL SIGNAL:
All signals are always displayed at 16:9 irrespective of their type.
• VIDEO ONLY:
Signals supplied from video devices only are displayed at 16:9.
To cancel the menu:
6. Press the MENU button.
Important:
• If you change the aspect ratio to 16:9, REAL, or FULL while displaying images on a 4:3 screen with the aspect
ratio set to NORMAL (4:3), images appear partly off screen.
• In such cases as when you keep displaying images in the 4:3 mode for a long time and then change the mode to
FULL, the masking areas may remain as afterimage around the displayed image. Consult your dealer in this case.
• When the input video signal is interrupted with NORMAL (16:9) or NORMAL (4:3) selected, the image turns blue
and appears partly off screen. In this case, set BACK COLOR in the INSTALLATION menu to BLACK.
EN-19
Viewing video images
A. Connecting the projector to video equipment
Preparation:
• Make sure that the power of the projector and that of the video equipment are turned off.
Connecting to a video player, etc.
Video player, or the like
To video
output
terminal 2
To VIDEO
IN terminal
1
To audio
input
terminals
3
Video cable
(option)
4
Audio cable
(option)
Video player, or the like
S-video cable (option)
S-VIDEO
1 To
IN terminal
To audio
output
terminals
To S-video
output
terminal
2
To audio
output
terminals
4
To audio
input
terminals
3
Audio cable
(option)
Video player, or the like
To VIDEO
IN terminal
(BNC)
To video
output
terminal
BNC cable (option)
Video player, or the like
To S-video (Y/C)
output terminals
To S-VIDEO IN
(Y and C) terminals
(BNC)
BNC cable (option)
1. Connect one end of a commercially available video cable
to the VIDEO IN terminal of the projector.
2. Connect the other end of the video cable to the video
output terminal of the video equipment.
3. Connect one end of a commercially available audio cable
to the audio input terminals (L/MONO, R) of the projector.
4. Connect the other end of the audio cable to the audio
output terminals (L, R) of the video equipment.
When the video equipment is equipped with the S-video
output terminal, make the connection as follows:
1. Connect one end of a commercially available S-video cable
to the S-VIDEO IN terminal of the projector.
2. Connect the other end of the S-video cable to the S-video
output terminal of the video equipment.
3. Connect one end of a commercially available audio cable
to the audio input terminals (L/MONO, R) of the projector.
4. Connect the other end of the audio cable to the audio
output terminals (L, R) of the video equipment.
When using the BNC connector:
(For VIDEO input)
• When the video output terminal of the connected video
equipment is BNC type, use the VIDEO IN terminal (BNC
type).
• Select VIDEO as the input source.
• When using the VIDEO IN terminal (BNC type) and the
VIDEO IN terminal (RCA type) at the same time, the video
signal input to the VIDEO IN terminal (RCA type) takes
priority.
When using the BNC connector:
(For S-VIDEO input)
• When the video output terminals of the connected video
equipment are BNC (Y/C) type, connect Y and C to the SVIDEO IN (Y and C) terminals (BNC type) respectively.
• Select S-VIDEO as the input source.
• When using the S-VIDEO IN (Y and C) terminals (BNC type)
and the S-VIDEO IN terminal (S type) at the same time, the
video signal input to the S-VIDEO IN terminal (S type) takes
priority.
• When connecting a monophonic video device, use the white (L) terminal to connect the audio cable. (The same
audio signal is output from the channels L and R of the AUDIO OUT terminal.)
• Also read the instruction manual of the equipment to be connected.
• Contact your dealer for details of connection.
When a TV tuner or VCR is connected:
When you use this projector with a TV tuner or VCR connected, no image may appear or a message of “NO SIGNAL”
may appear on the screen when you change the channel via any channel that is not being received. In such a case,
set the channels of the TV tuner or VCR again. To avoid such symptom, use the TV tuner or VCR with its channel skip
function (that is a function not to display channels that are not being received) enabled.
EN-20
Viewing video images (continued)
Projector + DVD player or HDTV decoder
Some DVD players have an output connector for 3-line fitting (Y, CB, CR). When connecting such DVD player with this
projector, use the COMPUTER/COMPONENT VIDEO IN-2 terminals.
BNC cable (option)
G
B
COMPUTER/COMPONENT
VIDEO IN-2
R
BNC-RCA connector (option)
Y CB(PB) CR(PR)
Audio cable (option)
DVD player or HDTV decoder
•
•
•
•
•
AUDIO IN-2
To audio output terminals
The terminal’s names Y, PB, and PR are given as examples of when a HDTV decoder is connected.
The terminal’s names vary depending on the connected devices.
Use BNC cables for connection.
Image may not be projected correctly with some DVD players.
If colors aren’t displayed correctly when the projector is connected to a high-definition video device having R, G,
and B output terminals, set COMPUTER INPUT to RGB in the SIGNAL menu. (See page 32.)
Connecting to video equipment having a HDMI terminal or DVI-D terminal
You can project high-quality images by connecting the COMPUTER/COMPONENT VIDEO DVI-D IN (HDCP) terminal
of this projector to video equipment having a HDMI output terminal or DVI-D terminal. In addition, this projector
supports HDCP and is able to receive encrypted digital video data that are output from DVD players.
• HDCP (High-bandwidth Digital Content Protection), developed by Intel Corporation, is a method to encrypt digital
video data for the purpose of copy protection.
• HDMI (High-Definition Multimedia Interface) is fully backward compatible with computers, displays and consumer
electronics devices incorporating the DVI standards.
• This projector can be linked with video devices equipped with HDMI output terminal or DVI-D output terminal.
However, with some of them, this projector may not display any image or not operate correctly.
• If this projector doesn’t display any image or not operate correctly, see the operation manual of the video device
for its connection.
• Use of a long cable may decrease the quality of projected images.
Connection (for video equipment having an HDMI terminal)
• Use a commercially available HDMI (with HDMI logo) cable.
• You don’t have to connect any cable for audio input. You can input video and audio using an HDMI cable only.
• When HDMI audio isn’t output, it may be output by turning off the power of the video equipment with the projector
and the video equipment connected to each other and then turning back on the power.
• Some cables may not be connected correctly depending on the size and shape of their connectors.
Equipment having an
HDMI terminal
To HDMI terminal
HDMI IN
HDMI (with HDMI logo) cable (option)
EN-21
Viewing video images (continued)
Connection (for video equipment having a DVI-D terminal)
Equipment having a
DVI-D terminal
To audio output
terminals
To DVI-D terminal
DVI cable (option)
COMPUTER/COMPONENT
VIDEO DVI-D IN (HDCP)
AUDIO DVI-D
Audio cable (option)
•
•
•
•
For connection to the DVI-D terminal, use a commercially available DVI cable.
Use AUDIO DVI-D terminal for audio input.
Some cables may not be connected correctly depending on the size and shape of their connectors.
When DVI is selected as the input source, settings of FINE SYNC., TRACKING, HOLD, etc. are unavailable.
When you connect this projector and a digital device (such as a DVD player) via the HDMI IN or COMPUTER/
COMPONENT VIDEO DVI-D IN (HDCP) terminal, black color may appear dark and deep, depending on the type
of the connected device.
• This depends on the black level setting of the connected device. There are 2 kinds of methods to digitally transfer
image data, in which different black level settings are employed respectively. Therefore, the specifications of the
signals output from DVD players differ, depending on the type of the digital data transfer method they use.
• Some DVD players are provided with a function to switch the methods to output digital signals. When your DVD
player is provided with such function, set it as follows.
EXPAND or ENHANCED → NORMAL
• See the users guide of your DVD player for details.
• When your digital device does not have such function, set INPUT LEVEL to ENHANCED in the ADVANCED
MENU of the IMAGE menu of this projector, or adjust the black color by viewing the image.
B. Plugging in the power cord
Plug the power cord in the same way as in the case of “Viewing computer images.” (See page 14.)
C. Installing the terminal cover
If necessary, install the terminal cover to the projector in the same way as in the case of “Viewing computer images.”
(See page 15.)
EN-22
Viewing video images (continued)
D. Projecting images
Preparation:
• Remove the lens cap.
Main power switch
POWER button
POWER indicator
STATUS indicator
POWER button
COMPUTER 1, 2 buttons
ENTER button
ZOOM/FOCUS button
LENS SHIFT button
COMPUTER/
DVI-D button
VIDEO/HDMI button
p, q, t, u buttons
ZOOM/FOCUS button
HDMI button
VIDEO button
S-VIDEO button
DVI-D(HDCP) button
p, q, t, u buttons
ENTER button
LENS SHIFT button
1. Put the projector into standby mode by pressing the main power switch. The POWER indicator lights up red.
• If the projector was turned off before the lamp was cooled down sufficiently last time, the fan may start rotating
and the POWER button may not work after the main power switch is turned ON. (The STATUS indicator blinks
green.) After the fan stops rotating, press the POWER button to turn back on the POWER indicator.
2. Turn on the power of the connected video equipment.
3. Press the POWER button.
• It may take about 1 minute for the lamp to light up.
• The lamp fails to light up on rare occasions. In such a case, wait for a few minutes and then try again.
• Do not cover the lens with the lens cap while the lamp is on. Do not strip off the aluminium sheet inside the
lens cap.
• After the POWER button is pressed, the image may flicker before the lamp becomes stable. This is not a
product malfunction.
• The lamp operation becomes stable in 1 minute after the power is turned on and then the lamp mode selected
in the menu is activated. During the activation, displayed images may be disturbed.
• The projector starts warming up when the POWER button is pressed. During the warm-up process, images
may appear dark and no commands are accepted.
• By blinking red, the STATUS indicator indicates that the lamp should be replaced soon. Replace the lamp when
the STATUS indicator blinks red. (See page 41.)
4. Press the ZOOM/FOCUS button to display the ZOOM/FOCUS menu.
5. Adjust with the  or  button to get a fine picture.
• When the ENTER button is pressed while the ZOOM/FOCUS menu is displayed, the adjustment mode is
switched between FAST and STEP. When FAST is selected, the speed of focus controlled by the  or  button
becomes fast, and it becomes slow when STEP is selected.
6. Select an input source.
• Press the VIDEO/HDMI button on the projector or the VIDEO, S-VIDEO or HDMI button on the remote control
that is corresponding to the terminal in use.
• The input source is switched between VIDEO, S-VIDEO and HDMI at every press of the VIDEO/HDMI button on
the projector.
• You cannot change the input source while the menu is being displayed.
• Though it may take some time before an image is displayed on the screen depending on the type of the input
signal, such symptom is not a malfunction.
• Some images become easier to view when the setting of aspect ratio is changed. (See page 19.)
• When projecting images from a DVD player that is connected to the COMPUTER/COMPONENT VIDEO DVI-D
IN (HDCP) terminal, press the COMPUTER/DVI-D button on the projector to select DVI or press the DVI-D
(HDCP) button on the remote control.
• When projecting images from a DVD player that is connected to the COMPUTER/COMPONENT VIDEO IN-1 or
COMPUTER/COMPONENT VIDEO IN-2 terminal, press the COMPUTER/DVI-D button on the projector or the
COMPUTER 1 or COMPUTER 2 button on the remote control.
• When COMPUTER 1 or COMPUTER 2 is chosen as the source, images supplied from the computer may
flicker. Press the  or  button on the remote control to reduce flicker, if it occurs. (Fine adjustment)
7. Adjust the position of the projector to keep an appropriate projection distance with which images are projected in
their specified sizes.
8. Adjust the position of the projector so that the projector and the screen are perpendicular to each other. (See page 10.)
• When the projector cannot be positioned perpendicularly to the screen, adjust the projection angle. (See page 11.)
9. Press the ZOOM/FOCUS button to display the ZOOM/FOCUS menu.
10.Adjust with the p or q button to get an approximate size.
• When the ENTER button is pressed while the ZOOM/FOCUS menu is displayed, the adjustment mode is
switched between FAST and STEP. When FAST is selected, the speed of zoom controlled by the p or q
button becomes fast, and it becomes slow when STEP is selected.
EN-23
Viewing video images (continued)
11.Press the LENS SHIFT button. The LENS SHIFT menu appears at the center of the screen.
12.Press the p or q button to adjust the vertical position and  or  button to adjust the horizontal position of the
displayed image.
• When the image is not displayed within the screen, adjust the projection angle. In addition, perform the
keystone adjustment, if necessary. (See page 11.)
Repeat steps 4, 5 and 9 to 12, if necessary.
Important:
• Focus, zoom and lens shift adjustment is possible in the normal picture mode only.
To stop projecting:
13.Press the POWER button.
• A confirmation message is displayed.
• To cancel the procedure, leave the projector for a while or press any button except the POWER button.
14.Press the POWER button again.
• The lamp goes out and the projector goes into a standby mode. In this standby mode, the STATUS indicator
blinks green.
15.Wait about 2 minutes for the STATUS indicator to be turned off.
• During this period of 2 minutes in the standby mode, the intake fan and exhaust fan rotate to cool the lamp.
• The air outlet fans rotate faster as the temperature around the projector rises.
• Though the fans make loud sounds during cooling, such symptom is not a malfunction.
16.Turn off the main power switch.
• The POWER indicator will go out.
• If the main power switch should be turned off or the power cord should be unplugged accidentally while either
the air inlet fan or the air outlet fans are operating or the lamp is on, allow the projector to cool down for 10
minutes with the power off. To light the lamp again, press the POWER button. If the lamp doesn’t light up
immediately, repeat pressing the POWER button 2 or 3 times. If it should still fail to light up, replace the lamp.
• Cover the lens with the lens cap to protect it from dust.
• For safety’s sake, unplug the power cord from the outlet.
• When you repeat turning off the main switch within 30 minutes from the lamp illumination, an error may occur
in the clock function of this product.
Instant Shut Down
You can turn off this projector just by turning off the power switch or unplugging the power cord without pressing the
POWER button.
• Don’t shut down the projector while the STATUS indicator is blinking after the lamp lights up because the lamp’s
life may be shortened.
• Don’t turn the projector back on right after shutting it down because the lamp’s life may be shortened. (Wait about
10 minutes before turning the projector back on.)
• Before shutting down the projector, be sure to close the menu screen. If you shut down the projector without
closing the menu, the setting data of the menu may not be saved.
• If you shut down the projector while controlling the projector using the network function, the application software
such as ProjectorView may fail. For details, see “User Guide of LAN Control Utility” contained in the CD-ROM.
Volume from the speaker
Press the VOLUME + or - button to change the volume from the speaker.
The volume control bar will appear on the screen.
VOLUME
15
• The volume control bar will disappear about 10 seconds after the VOLUME button is released.
• The VOLUME buttons don’t function while the menu selection bar or the menu is being displayed.
• When a high-level audio signal, such as a DVD audio signal, is supplied to the AUDIO IN terminals, the output
from the speaker may be distorted.
• When the audio cable is connected to the AUDIO OUT terminal, the speaker output is muted.
• The volume of the audio from the AUDIO OUT terminal is also changed by pressing the VOLUME buttons.
• The volume of the audio from the AUDIO OUT terminal varies within the range between 0 and 31.
Setting the aspect ratio
You can change the aspect ratio of the input video signal (or the ratio of width to height of the image). Change the
setting according to the type of the input video signal. (See page 19.)
EN-24
Menu operation
You can make various settings using the displayed menus.
Menu display mode and menu type
There are two menu display modes: QUICK MENU mode and DETAIL MENU mode.
Each mode has the following menus.
Menus displayed in the QUICK MENU mode
The QUICK MENU contains frequently used setting items and the INFOMATION menu shows the projector condition.
QUICK MENU (page 27)
QUICK MENU
INFORMATION
COLOR
ENHANCER
AUTO
CONTRAST
0
BRIGHTNESS
0
COLOR TEMP.
STANDARD
SHARPNESS
0
LAMP MODE
STANDARD
ASPECT
COLOR
SELECT
USER MENU
DETAIL MENU
INFORMATION menu (page 28)
0H
LAMP TIME (LOW)
INPUT
COMPUTER2
RESOLUTION
1024 x 768
NORMAL (FULL)
VERTICAL
FREQUENCY
75.04 Hz
0
HORIZONTAL
FREQUENCY
60.02 KHz
SYNC. TYPE
5WIRE
COLOR
R G B
H
V
OK
Menus displayed in the DETAIL MENU mode
Following 5 menus are displayed for making detailed settings.
IMAGE menu (page 29)
INSTALLATION menu (page 30)
opt.
INSTALLATION
IMAGE
COLOR
ENHANCER
AUTO
CONTRAST
FEATURE
LAMP MODE
STANDARD
ASPECT
0
STANDBY MODE
STANDARD
PASSWORD
FUNCTION
BRIGHTNESS
0
COLOR TEMP.
STANDARD
AUTO POWER
ON
AUTO POWER
OFF
COLOR
0
TINT
0
SHARPNESS
ADVANCED MENU
ON
0
OFF
MEMORY CALL
H
V
R
RG
GB
B
RESOLUTION
(MEMORIZE )
OK
opt.
SIGNAL
INFORMATION
AUTO
0H
LAMP TIME (LOW)
1024 x 768
HORIZ. POSITION
0
VERT. POSITION
0
INPUT
FINE SYNC.
0
RESOLUTION
1024 x 768
TRACKING
0
VERTICAL
FREQUENCY
75.04 Hz
HORIZONTAL
FREQUENCY
60.02 KHz
SYNC. TYPE
5WIRE
COMPUTER INPUT
OVER SCAN
HOLD
RGB
100%
OFF
USER
COMPUTER2
R G B
H
V
?
BLUE
INFORMATION menu (page 28)
opt.
U
CINEMA MODE
BLACK
AV MUTE MODE
LENS LOCK
SIGNAL menu (page 32)
MENU POSITION
OFF
ON
SPLASH SCREEN
BACK COLOR
OK
OFF
GO
IMAGE CAPTURE
IMAGE REVERSE
A
FEATURE menu (page 31)
opt.
opt.
OK
EN-25
1.
AUTO
VIDEO SIGNAL
AUTO
SETUP
AUTO
SCART INPUT
AË
NORMAL (FULL)
DISPLAY INPUT
OFF
LANGUAGE
English
RESET ALL
OK
Menu operation (continued)
Basic procedure for setting the menus
1. Press the MENU button.
• The menu selection bar is displayed in the
QUICK MENU mode.
Changing from the QUICK MENU
mode to the DETAIL MENU mode
1. Display the QUICK MENU according to steps 1 to 3
described on the left.
Selectable menus are displayed
by icons. (The menu icon being
selected is displayed on a blue
background.)
QUICK MENU
QUICK MENU
The name of the menu being
selected is displayed.
2. Press the  or  button to select a menu to use.
3. Press the ENTER button (or  button).
• The selected menu is displayed.
CONTRAST
0
BRIGHTNESS
0
COLOR TEMP.
STANDARD
0
BRIGHTNESS
0
COLOR TEMP.
STANDARD
SHARPNESS
0
LAMP MODE
STANDARD
ASPECT
SELECT
USER MENU
QUICK MENU
AUTO
AUTO
CONTRAST
NORMAL (FULL)
COLOR
The item being selected is
displayed in red letters.
COLOR
ENHANCER
COLOR
ENHANCER
0
COLOR
OK
DETAIL MENU
2. Press the  or  button to select DETAIL MENU.
QUICK MENU
SHARPNESS
0
COLOR
ENHANCER
AUTO
LAMP MODE
STANDARD
CONTRAST
0
ASPECT
NORMAL (FULL)
BRIGHTNESS
0
COLOR
0
COLOR TEMP.
STANDARD
SELECT
USER MENU
DETAIL MENU
COLOR
SHARPNESS
0
OK
LAMP MODE
STANDARD
ASPECT
4. Press the  or  button to select an item to adjust.
NORMAL (FULL)
COLOR
0
SELECT
USER MENU
DETAIL MENU
COLOR
OK
QUICK MENU
COLOR
ENHANCER
AUTO
CONTRAST
0
BRIGHTNESS
0
COLOR TEMP.
STANDARD
LAMP MODE
STANDARD
3. Press the ENTER button.
• The DETAIL MENU mode is activated. (You can
select 5 menus.)
5. Set the selected
item by pressing0 the  or  button.
SHARPNESS
ASPECT
QUICK
MENU
COLOR
COLOR
SELECT
ENHANCER
USER MENU
CONTRAST
DETAIL MENU
opt.
IMAGE
NORMAL (FULL)
• Make settings according to steps 2 to 5 on the
left, as necessary.
0
AUTO
COLOR
2
OK
BRIGHTNESS
0
COLOR TEMP.
STANDARD
4. To cancel the menu, press the MENU button
several times.
6. To cancel the
menu, press the MENU
button
0
SHARPNESS
several times.
LAMP MODE
STANDARD
Important:
ASPECT
NORMAL (FULL)
• When an item
marked with “ ” is
COLOR
0 selected,
pressing theSELECT
ENTER
button
makes
COLOR its value
USER MENU
effective or DETAIL
displays
another screen
for further
OK
MENU
setting.
• When the MENU button doesn’t function, unplug
the power cord from the wall outlet. Wait about 10
minutes, plug the power cord in, and try again.
EN-26
Menu operation (continued)
Settings of each menu item
Menus displayed in the QUICK MENU mode
QUICK MENU
QUICK MENU
COLOR
ENHANCER
AUTO
CONTRAST
0
BRIGHTNESS
0
COLOR TEMP.
STANDARD
SHARPNESS
0
LAMP MODE
STANDARD
ASPECT
COLOR
NORMAL (FULL)
*
SELECT
USER MENU
SETTING
AUTO
PRESENTATION
STANDARD
THEATER
sRGB
USER
CONTRAST
BRIGHTNESS
COLOR TEMP.
±30
±30
STANDARD / LOW /
HIGH
USER
SHARPNESS
LAMP MODE
±5
STANDARD
LOW
ASPECT
NORMAL (FULL)
NORMAL (16:9)
NORMAL (4:3)
16:9
REAL
FULL
(USER MENU) *
SELECT USER MENU
DETAIL MENU
*
COLOR / TINT /
STANDBY MODE /
IMAGE REVERSE /
MENU POSITION /
CINEMA MODE /
SCART INPUT /
LANGUAGE
OK
*
OK
DETAIL MENU
ITEM
COLOR ENHANCER
0
COLOR
FUNCTION
Select to optimize the settings automatically depending on the input signal.
(Select this option for normal use.)
Select to make the displayed image look bright and crisp.
Select to make the displayed image look natural.
This option, suitable for viewing movies, makes the displayed image look soft
and smooth.
Select to give priority to the color reproducibility.
The values of the gamma curve, BrilliantColor™, color intensity, and color
balance that are set by USER of COLOR ENHANCER in the IMAGE menu
are applied. (See page 29.)
Use to adjust the contrast of the projected image. (See page 33.)
Use to adjust the brightness of the projected image. (See page 33.)
Select from the predetermined color temperatures.
The color temperature that is set by USER of COLOR TEMP. in the IMAGE
menu is applied. (See page 29.)
Use to adjust the sharpness of the projected image. (See page 33.)
Select this option when you want to view images in a well-lit room.
Select to moderate the intensity of the lamp. The operating sound is reduced
and the lamp lifetime becomes longer.
• When the lamp mode is switched, the projected image may flicker.
• Frequent switching of the lamp mode may damage the lamp.
Input video signal is displayed at the max height (800 pixels) or max width
(1280 pixels) of the panel while its aspect ratio is maintained.
Select this setting when using a 16:9 screen.
Select this setting when using a 4:3 screen.
Regardless of the type of input signal, image is displayed at 16:9 aspect ratio
(1280 x 720 pixels). Select to expand squeezed (or horizontally compressed)
images such as DVD images to 16:9. When selecting 16:9 of ASPECT in
the FEATURE menu, you can select whether or not to display signals at 16:9
depending on their type. (See page 19.)
Input video signal is displayed at its original pixel size.
Select to project images in full size (1280 x 800 pixels) irrespective of type of
input signal.
*: The item selected in SELECT USER MENU below and its value are
displayed.
Select the item to be displayed in the preceding row. For the details of the
selectable items, see the following pages.
• COLOR, TINT ...... page 29
• STANDBY MODE, IMAGE REVERSE ...... page 30
• MENU POSITION, CINEMA MODE, SCART INPUT, LANGUAGE ...... page
31
Select to change the menu display mode to the DETAIL MENU mode.
• When COLOR ENHANCER is sRGB, COLOR TEMP., COLOR and TINT can’t be adjusted.
• When the setting of COLOR ENHANCER is changed, the displayed image may be disturbed.
EN-27
Menu operation (continued)
Menus displayed in the QUICK MENU mode and the DETAIL MENU mode
INFORMATION menu
INFORMATION
LAMP TIME (LOW)
INPUT
0H
COMPUTER2
RESOLUTION
1024 x 768
VERTICAL
FREQUENCY
75.04 Hz
HORIZONTAL
FREQUENCY
60.02 KHz
SYNC. TYPE
5WIRE
R G B
H
ITEM
LAMP TIME (LOW)
INPUT
RESOLUTION
VERTICAL FREQUENCY
HORIZONTAL FREQUENCY
SYNC. TYPE
V
DESCRIPTION
This item shows a lamp operating time (hour) calculated based on that LAMP MODE is LOW.
• When the LAMP MODE is STANDARD, this item shows a longer lamp operating time than
the actual time. (See page 42 for the interval of lamp replacement.)
• When the lamp operating time is 0 to 10 hours, “0H” is displayed. The lamp operating time
exceeding 10 hours is indicated by the actual hours.
• When the lamp operating time reaches 3000 hours, the bar turns to yellow. When it
reaches 3800 hours, the bar turns to red.
Indicates the name of the terminal to which the currently projected video signal is being input.
Indicates the resolution of the currently projected video signal.
Indicates the vertical frequency of the currently projected video signal.
Indicates the horizontal frequency of the currently projected video signal.
Indicates the type of the sync signal for the currently projected video signal.
EN-28
Menu operation (continued)
Menus displayed in the DETAIL MENU mode
IMAGE menu
opt.
opt.
IMAGE
IMAGE
COLOR
ENHANCER
AUTO
CONTRAST
0
NOISE REDUCTION
ON
BRIGHTNESS
0
CTI
ON
COLOR TEMP.
STANDARD
COLOR
0
TINT
0
SHARPNESS
ADVANCED MENU
ITEM
COLOR ENHANCER
SETTING
AUTO
PRESENTATION
STANDARD
THEATER
sRGB
USER
COLOR
TINT
SHARPNESS
ADVANCED MENU
NOISE REDUCTION
±30
±30
STANDARD / LOW /
HIGH
USER
±10
±10
±5
OK
ON / OFF
ON / OFF
±5
CONTRAST
BRIGHTNESS
COLOR TEMP.
CTI
INPUT LEVEL
ENHANCED /
NORMAL
•
•
•
•
•
ADVANCED MENU
INPUT LEVEL
0
0
OK
FUNCTION
Select to optimize the settings automatically depending on the input signal.
(Select this option for normal use.)
Select to make the displayed image look bright and crisp.
Select to make the displayed image look natural.
This option, suitable for viewing movies, makes the displayed image look soft
and smooth.
Select to give priority to the color reproducibility.
Select to set the gamma curve, set BrilliantColor™ or adjust the color
intensity or color balance as desired. (See page 34.)
Use to adjust the contrast of the projected image. (See page 33.)
Use to adjust the brightness of the projected image. (See page 33.)
Select from the predetermined color temperatures.
Use to adjust the color temperature to a desired value. (See page 34.)
Use to adjust the color thickness of the projected image. (See page 33.)
Use to adjust the color tint of the projected image. (See page 33.)
Use to adjust the sharpness of the projected image. (See page 33.)
The ADVANCED MENU is displayed for the following settings.
Use to reduce noise and roughness in the image when noisy video signal is
input.
Use to correct smeared color boundaries.
For analog signal input:
The input level of video signal differs among devices to be connected. High
input level causes solid white in displayed image and low input level causes
displayed image to get dark. Use this menu to adjust the input level of analog
video signal.
For digital signal input:
When a digital signal is input, ENHANCED and NORMAL are switchable. (See
page 22.)
When COLOR ENHANCER is sRGB, COLOR TEMP., COLOR and TINT can’t be adjusted.
When the setting of COLOR ENHANCER is changed, the displayed image may be disturbed.
When the COMPUTER1, COMPUTER2, DVI or HDMI is selected as the input source, COLOR and TINT can’t be adjusted.
TINT is available only when the NTSC signal is input.
INPUT LEVEL is unavailable when the digital signal is supplied from the YCBCR/YPBPR terminal of the connected device.
EN-29
Menu operation (continued)
INSTALLATION menu
opt.
opt.
INSTALLATION
INSTALLATION
LAMP MODE
STANDARD
STANDBY MODE
STANDARD
AUTO POWER
ON
AUTO POWER
OFF
IMAGE CAPTURE
ON
SPLASH SCREEN
BACK COLOR
AV MUTE MODE
IMAGE REVERSE
LENS LOCK
ITEM
LAMP MODE
SETTING
STANDARD
LOW
STANDBY MODE
STANDARD
LOW
AUTO POWER ON
ON / OFF
AUTO POWER OFF
OFF / 5-60min
IMAGE CAPTURE
SPLASH SCREEN
GO
ON / OFF
BACK COLOR
BLUE / BLACK /
IMAGE
AV MUTE MODE
BLACK / IMAGE
IMAGE REVERSE
OFF
MIRROR
INVERT
MIRROR INVERT
LENS LOCK
ZOOM/FOCUS LOCK
LENS SHIFT LOCK
LENS SHIFT RESET
OK
ON / OFF
ON / OFF
OK
LENS LOCK
ZOOM/FOCUS
LOCK
OFF
LENS SHIFT LOCK
OFF
LENS SHIFT
RESET
OFF
OFF
OK
GO
ON
BLUE
BLACK
OFF
OK
FUNCTION
Select this option when you want to view images in a well-lit room.
Select to moderate the intensity of the lamp. The operating sound is reduced
and the lamp lifetime becomes longer.
Select this option when you control the projector via LAN during power
standby.
Select this option when you don’t control the projector via LAN during power
standby. This option disables the LAN terminal and reduces the power
consumption during the power standby.
When ON is chosen, the lamp is automatically lit when the power cord is
plugged in the wall outlet. Choose ON when using the projector mounted on
the ceiling.
• The projector is in the stand-by mode when the lamp is off. Use the
remote control to turn on the lamp.
Use to set the time elapsed before the projector enters the stand-by mode
when there is no signal input from the source.
Use to capture the screen for the splash screen. (See page .37.)
Choose ON to display the splash screen when the power is turned on.
• The splash screen can be changed. (See page 37.)
Use to select the background from among BLUE, BLACK and IMAGE, which
will be displayed when there is no signal input from the source. When IMAGE
is selected, the splash screen will be displayed.
Use to choose the background, either BLACK, or IMAGE, which will be
displayed when the AV MUTE button is pressed. When IMAGE is chosen, the
splash screen will be displayed.
Select when viewing images from the front with the projector installed on the
floor.
Select when viewing images projected from the behind of the screen with the
projector installed on the floor.
Select when viewing images projected from the behind of the screen with the
projector installed on the ceiling.
Select when viewing images from the front with the projector installed on the
ceiling.
The LENS LOCK menu is displayed for the following settings.
Use to enable or cancel the FOCUS LOCK and ZOOM LOCK.
Use to enable or cancel the LENS SHIFT LOCK.
Use to reset the position of the lens to the factory setting.
• Regardless of the setting of LAMP MODE in the INSTALLATION menu, the STANDARD lamp mode is activated by default
whenever the projector is turned on. When LAMP MODE has been set to LOW, the lamp mode changes from STANDARD to
LOW about 1 minute after turn-on.
• When the lamp mode is switched, the projected image may flicker.
• Frequent switching of the lamp mode may damage the lamp.
• You can’t set IMAGE CAPTURE and SPLASH SCREEN when PASSWORD FUNCTION in the FEATURE menu has been set to
SPLASH ID SCREEN to enable the password lock.
• When you continue projection for a long time with BACK COLOR or AV MUTE MODE set to IMAGE, an afterimage may persist
on the screen. Consult your dealer in this case.
EN-30
Menu operation (continued)
FEATURE menu
opt.
FEATURE
ASPECT
NORMAL (FULL)
PASSWORD
FUNCTION
DISPLAY INPUT
MENU POSITION
CINEMA MODE
?
ITEM
ASPECT
SETTING
NORMAL (FULL)
NORMAL (16:9)
NORMAL (4:3)
16:9
REAL
FULL
PASSWORD
FUNCTION
MENU POSITION
CINEMA MODE
VIDEO SIGNAL
SETUP
DISPLAY INPUT /
MENU ACCESS /
SPLASH ID SCREEN
1 (upper left) / 2 (lower right)
AUTO
FILM
VIDEO
AUTO / NTSC / PAL /
SECAM / 4.43NTSC / PALM / PAL-N / PAL-60
AUTO
OFF
3.75% / 7.5%
SCART INPUT
ON / OFF
LANGUAGE
/ English / Español /
Deutsch / Français / Italiano
/
/
/
/
PORTUGUÊS / SVENSKA /
POLSKI
OK
RESET ALL
AUTO
VIDEO SIGNAL
AUTO
SETUP
AUTO
SCART INPUT
AË
1.
OFF
LANGUAGE
English
RESET ALL
OK
FUNCTION
Input video signal is displayed at the max height (800 pixels) or max width
(1280 pixels) of the panel while its aspect ratio is maintained.
Select this setting when using a 16:9 screen.
Select this setting when using a 4:3 screen.
Regardless of the type of input signal, image is displayed at 16:9 aspect ratio
(1280 x 720 pixels). Select to expand squeezed (or horizontally compressed)
images such as DVD images to 16:9. Press the ENTER button to select
whether or not to display signals at 16:9 depending on their type. (See page
19.)
Input video signal is displayed at its original pixel size.
Select to project images in full size (1280 x 800 pixels) irrespective of type of
input signal.
Use to enable or cancel the password lock. See page 38 for details.
Use to change the position of the menu.
The film mode will be automatically activated when a film source signal is
input.
Select AUTO for normal use.
When flicker occurs on the screen, frame dropping or other incorrect display
occurs, or jaggies on slanting lines are remarkable, select either FILM or
VIDEO, which improves the symptom better.
Fixed to the film mode.
The film mode will not be activated.
When AUTO is selected, the appropriate video format is automatically
selected depending on the input signal. If the image isn’t displayed correctly,
select the desired video format manually.
Select to change the SETUP mode automatically.
Select to make black lighter.
Select to make black thicker.
• When 7.5% is chosen, the brightness is decreased by the set-up cancel
function for the U.S. Choose OFF when the image is dark.
Choose ON when connecting the projector with a device equipped with the
SCART terminal that can output RGB signal. SCART terminal is used mainly
in Europe. Choose OFF normally. (Available only for the input signal from the
COMPUTER/COMPONENT VIDEO IN-1 terminal.)
Use to select the language used in the menus.
Use to reset the settings of the menu (excluding IMAGE CAPTURE,
PASSWORD FUNCTION and LANGUAGE) to the factory setting values.
•
•
•
•
CINEMA MODE can be adjusted only when a TV60, TV50, 480i, 576i or 1080i signal is being displayed.
When SCART INPUT is set to ON, nothing is output to the external monitor.
When SCART INPUT is set to ON, normal computer signals aren’t projected.
Use a commercially available SCART-Mini D-SUB 15-pin cable when connecting this projector with an AV device equipped
with the SCART terminal.
• Some AV devices equipped with the SCART terminal aren’t compatible with this projector.
EN-31
Menu operation (continued)
SIGNAL menu
opt.
opt.
SIGNAL
A
MEMORY CALL
U
H
V
RESOLUTION
(MEMORIZE )
AUTO
SIGNAL
SIGNAL
RESOLUTION (MEMORIZE)
USER
HORIZ. POSITION
0
VERTICAL
FREQUENCY
HORIZONTAL
FREQUENCY
VERT. POSITION
0
HORIZ. PIXELS
FINE SYNC.
0
VERT. LINES
0
EXECUTE
OK
CANCEL
OK
1024 x 768
TRACKING
R
RG
GB
B
opt.
CLAMP POSITION
75.04 Hz
CLAMP WIDTH
60.02 KHz
1024
768
?
VERT. SYNC
LPF
1
1
AUTO
OFF
SHUTTER(U)
0
SHUTTER(L)
0
COMPUTER INPUT
RGB
OVER SCAN
100%
SHUTTER(LS)
0
HOLD
OFF
SHUTTER(RS)
0
USER
OK
ITEM
MEMORY CALL
RESOLUTION (MEMORIZE
SETTING
AUTO /
MEMORY 1
MEMORY 2
)
VERTICAL FREQUENCY
HORIZONTAL FREQUENCY
HORIZ. PIXELS
640-1920
VERT. LINES
350-1200
EXECUTE
OK
CANCEL
OK
HORIZ. POSITION
VERT. POSITION
FINE SYNC.
TRACKING
COMPUTER INPUT
0-999
0-999
0-31
0-9999
AUTO
RGB
YCBCR/YPBPR
OVER SCAN
HOLD
USER
CLAMP POSITION
CLAMP WIDTH
VERT.SYNC
100%-90%
OFF / ON
OK
1-255
1-63
AUTO / OFF
ON / OFF
0-38
0-38
0-63
0-63
LPF
SHUTTER(U)
SHUTTER(L)
SHUTTER(LS)
SHUTTER(RS)
/
FUNCTION
Use to select the setting of RESOLUTION (MEMORIZE) already saved.
Impossible to select if no setting has been saved. AUTO is selected by
default. It optimizes the signal format automatically depending on the type of
video signal supplied from the computer. Press the ENTER button to clear the
setting already saved.
The current resolution is displayed. To change the current setting, press the
ENTER button to display the RESOLUTION (MEMORIZE) menu. The new
setting can be saved to MEMORY 1 or MEMORY 2.
The vertical frequency of the currently projected video signal is displayed.
The horizontal frequency of the currently projected video signal is displayed.
The number of horizontal pixels of the currently projected video signal is
displayed. When you change the current setting, select EXECUTE, and then
press the ENTER button, the image is automatically adjusted according to
the resolution you set. The adjustment result can be saved to MEMORY 1 or
MEMORY 2.
The number of vertical pixels of the currently projected video signal is
displayed. When you change the current setting, select EXECUTE, and then
press the ENTER button, the image is automatically adjusted according to
the resolution you set. The adjustment result can be saved to MEMORY 1 or
MEMORY 2.
Press the ENTER button to start the automatic adjustment. At the completion
of the automatic adjustment, a message is displayed and you can save the
adjustment result to MEMORY 1 or MEMORY 2.
The process to change the current resolution is canceled and the SIGNAL
menu is displayed.
Use to adjust the horizontal position of the projected image.
Use to adjust the vertical position of the projected image.
Use to eliminate flickering or blur, if appears, viewing the projected image.
Use to eliminate vertical wide stripes, if appears, viewing the projected image.
The proper setting is automatically selected.
Select this option when connecting the projector to high definition video
equipment having R, G, and B output terminals.
Select this option when connecting the projector to a DVD player or other device
having Y, CB, and CR (or Y, PB, and PR) component video output terminals.
Use to adjust the display area of projected image.
Use to adjust the image when flagging occurs near the top of the screen.
The USER menu is displayed for the following adjustments.
Use to correct solid white or solid black in the projected image.
Use to correct solid black in the projected image.
Use to adjust the image when its motion doesn’t run smoothly. Select AUTO
for normal use.
Use to select whether or not to enable the LPF.
Use to adjust the image when noise appears on the top part of the image.
Use to adjust the image when noise appears on the bottom part of the image.
Use to adjust the image when noise appears on the left half of the image.
Use to adjust the image when noise appears on the right half of the image.
• Though horizontal strips may appear on the enlarged projected image, such symptom is not a malfunction.
• When you change the horizontal or vertical position to a large extent, noise may appear.
• The adjustable range of the vertical position varies depending on the type of the input signal. Though the image may stay in the same
position even when the setting value is changed, such symptom is not a malfunction.
• When you increase the setting value of OVER SCAN, noise may appear on the screen.
• See pages 35 and 36 for the detailed setting procedure.
Important:
• You can set the IMAGE menu and the SIGNAL menu only when the signal is supplied.
EN-32
Adjusting projected images
To adjust the brightness (CONTRAST and BRIGHTNESS):
You can make adjustments for the brightness of the projected image using the menu.
(See page 26 for menu setting.)
1. Display the QUICK MENU or IMAGE menu.
2. Select CONTRAST or BRIGHTNESS by pressing the  or  button.
3. Adjust the selected item by pressing the  or  button.
To cancel the menu:
4. Press the MENU button.
CONTRAST
Select to adjust the contrast of the image. Every time the  button is pressed, the image becomes brighter and more
defined. Every time the  button is pressed, the image becomes darker and less defined.
BRIGHTNESS
Every time the  button is pressed, the image becomes brighter. Every time the  button is pressed, the image
becomes darker.
To adjust the color (COLOR and TINT):
You can adjust the color of the projected image using the menu.
(See page 26 for menu setting.)
1. Display the QUICK MENU or IMAGE menu.
2. Select COLOR or TINT by pressing the  or  button. • COLOR or TINT is unavailable when COMPUTER1, COMPUTER2, DVI or HDMI is selected as the input source.
• TINT is available only when the NTSC signal is input.
3. Adjust the selected item by pressing the  or  button.
To cancel the menu:
4. Press the MENU button.
COLOR
Use to adjust the color thickness of the projected image. Every time the  button is pressed, the color becomes
thicker. Every time the  button is pressed, the color becomes lighter.
TINT
Use to adjust the tint of the projected image. Every time the  button is pressed, the image appears more greenish.
Every time the  button is pressed, the image appears more reddish.
To sharpen or soften the projected image (SHARPNESS):
You can adjust the sharpness of the projected image using the menu.
(See page 26 for menu setting.)
1. Display the QUICK MENU or IMAGE menu.
2. Select SHARPNESS by pressing the  or  button.
3. Adjust the selected item by pressing the  or  button.
To cancel the menu:
4. Press the MENU button.
To adjust the tone of white (COLOR TEMP.):
You can select a preset color temperature (white tone) using the menu.
(See page 26 for menu setting.)
1. Display the QUICK MENU or IMAGE menu.
2. Select COLOR TEMP. by pressing the  or  button.
3. Select your desired color temperature by pressing the  or  button.
To cancel the menu:
4. Press the MENU button.
To adjust the tone of white (To customize the color temperature):
To customize (and store) the color temperature to your preference, carry out the following procedure.
(See page 26 for menu setting.)
1. Select COLOR TEMP. in the IMAGE menu.
COLOR TEMP.–USER
2. Press the  or  button to select USER .
CONTRAST R
3. Press the ENTER button.
CONTRAST G
4. Press the  or  button to select the desired item.
CONTRAST B
5. Press the  or  button to adjust the selected item.
BRIGHTNESS R
6. Repeat steps 4 and 5 for optimum adjustment results.
EN-33
0
0
0
0
BRIGHTNESS G
0
BRIGHTNESS B
0
Adjusting projected images (continued)
To cancel the menu:
7. Press the MENU button.
To enable the stored color temperature:
1. Set COLOR TEMP. to USER in the QUICK MENU or set it to USER
in the IMAGE menu.
About color temperature
There are different kinds of white color. Color temperature is a way to show the differences in white. White of which
temperature is low appears reddish. When the color temperature rises, white appears bluish. For example, you can
change the color temperature using the following procedures.
To raise the color temperature: Increase the CONTRAST B (blue) and decrease the CONTRAST R (red).
To reduce the color temperature: Decrease the CONTRAST B (blue) and increase the CONTRAST R (red).
• If you set all of CONTRAST R, G, and B to negative values, the original brightness of the image can’t be
obtained even when you maximize CONTRAST in the IMAGE menu.
Color Enhancer
opt.
You can set the user-defined balance between the brightness and hue using the menu. (See page 26 for menu
IMAGE
setting.)
COLOR
With the IMAGE menu:
1. Display the IMAGE menu.
2. Select COLOR ENHANCER by pressing the  or  button.
3. Select USER by pressing the  or  button.
4. Press the ENTER button.
5. Select an item you want to set by pressing the  or  button.
ENHANCER
CONTRAST
COLOR
ENHANCER–USER
BRIGHTNESS
GAMMA MODE
COLOR TEMP.
AUTO
0
0
DYNAMIC
STANDARD
BrilliantColorTM
COLOR
2
0
RGB–COLOR
TINT
0
0
RGB–TINT
SHARPNESS
0
0
OK
ADVANCED MENU
GAMMA mode
Use this item to set the gamma optimally.
DYNAMIC �� Select when viewing images supplied from the computer.
NATURAL �� Select when viewing images supplied from the video device.
DETAIL ��� Select when viewing images of which brightness should be kept relatively low, such as movies and
music performance.
BrilliantColor™
Use this item to make the colors having medium brightness such as yellow and skin tone look natural. Press the 
button to decrease the value to lessen the effect. Press the  button to increase the value to heighten the effect.
(BrilliantColor™ doesn’t work at value 0.)
6. Select a setting value by pressing the  or  button.
• For more enhanced color reproduction, set BrilliantColor™ to 0. The white portion of the color wheel will be
disabled and you can reproduce true-to-life images.
RGB-COLOR
Use to adjust the color intensity of the projected image. Every time the  button is pressed, the color becomes
thicker. Every time the  button is pressed, the color becomes lighter.
RGB-TINT
Use to adjust the color balance of the projected image. Every time the  button is pressed, the image appears more
greenish. Every time the  button is pressed, the image appears more reddish.
Important:
• You can adjust Color Enhancer also by pressing the CE button on the remote control.
With the remote control:
1. Press the CE button on the remote control.
A window for color enhancer adjustment appears on the upper right of the screen.
2. Press the  or  button to select USER .
3. Press the ENTER button.
4. Press the  or  button to select GAMMA MODE, BrilliantColor™, RGB-COLOR or RGB-TINT.
5. Press the  or  button to adjust the selected item.
EN-34
Adjusting projected images (continued)
How to adjust the computer image
This projector automatically selects a proper signal format according to the type of video signal supplied from the
computer. However, video signals from the computer may not be projected correctly depending on the types of the
computer and images to be projected. In such a case, make adjustment according to the flowchart below.
When the size and position of
the computer image are not correct.
Project a bright computer image containing as many texts and characters as possible.
Note) Disable the screen saver if it is active.
Press the AUTO POSITION button.
Settings are automatically and optimally adjusted for the input signal.
NO
Image is projected
correctly.
YES
Display the screen resolution setting menu of your computer.
(Example: In the case of Windows® PC, right-click on the desktop, select Properties, and click the
Settings tab to display the screen resolution setting.)
The screen
resolution setting of your computer
is different from the setting of RESOLUTION
(MEMORIZE ) in the SIGNAL menu
of the projector.
NO
YES
Select RESOLUTION (MEMORIZE
and press the ENTER button.
) in the SIGNAL menu
Set HORIZ. PIXELS and VERT. LINES to the values of the screen resolution of your computer.
(Example: When the screen resolution of the computer is 1280x800, set HORIZ. PIXELS to 1280 and
VERT. LINES to 800.)
Select EXECUTE and press the ENTER button.
Automatic adjustment starts according to the selected resolution.
NO
Image is projected
correctly.
Perform manual
adjustment.
YES
After the memory saving
massage is displayed,
select MEMORY 1 or
MEMORY 2 and press the
ENTER button.
YES
After the memory saving
massage is displayed,
select MEMORY 1 or
MEMORY 2 and press the
ENTER button.
NO
When you don’t save
the adjustment result,
press the MENU button.
Adjustment is canceled.
Adjust HORIZ. POSITION, VERT. POSITION, and TRACKING
in the SIGNAL menu. For details, see “Simple method to
adjust the image position.” (See page 36.)
Adjustment is completed.
EN-35
Adjusting projected images (continued)
How to adjust the image supplied from the computer using the menu:
Carry out the following procedures according to the symptoms.
Wide strips appear. ��������������� Adjust TRACKING in the SIGNAL menu.
The projected image flickers.
The projected image is blurred.��������������������������������������Adjust FINE SYNC. in the SIGNAL menu.
The projected image is displaced horizontally.��������������Adjust HORIZ.POSITION in the SIGNAL menu. Every time the
 button is pressed, the image moves to the right. Every time
the  button is pressed, the image moves to the left.
The projected image is displaced vertically.������������������Adjust VERT.POSITION in the SIGNAL menu. Every time the 
button is pressed, the image moves down. Every time the 
button is pressed, the image moves up.
The top part of the image flags.������������������������������������� Change the setting of HOLD in the SIGNAL menu. Select ON ,
press the ENTER button, and adjust BEGIN or END to minimize
the flagging.
A solid black or solid white appears in the image. �������� Adjust CLAMP POSITION or CLAMP WIDTH in the SIGNAL
- USER menu.
The motion doesn’t run smoothly.����������������������������������Adjust VERT. SYNC in the SIGNAL - USER menu. Select
AUTO for normal use.
Noise appears on the right or left half of the image.������Adjust SHUTTER(LS) or SHUTTER(RS) in the SIGNAL - USER
menu.
Noise appears on the top or bottom part of the image.������� Adjust SHUTTER(U) or SHUTTER(L) in the SIGNAL - USER
menu.
1. Display the SIGNALmenu.
2. Press the  or  button to select an item to adjust.
3. Adjust the selected item by pressing the  or  button.
To cancel the menu:
4. Press the MENU button.
Simple method to adjust the image position
To adjust the horizontal position:
1. Align the left edge of the image with the left side of the screen by adjusting HORIZ.POSITION. Then, align the
right edge of the image with the right side of the screen by adjusting TRACKING.
2. Repeat step 1 above to complete the adjustment of the horizontal position.
To adjust the vertical position:
3. Align the upper edge of the image with the upper side of the screen by adjusting VERT.POSITION.
LPF (Progressive filter)
You can select whether or not to enable the LPF.
Vertical or horizontal streak noise may appear on the projected image, depending on the type of the DVD player or
game console you use. In such a case, you can reduce such streak noise by enabling the LPF. However, projected
images become softened slightly.
EN-36
Advanced features
Setting of the image displayed
during startup or muting
You can display your desired image as the startup
screen (or splash screen). Using the menu, you can
also use such image as a background that is displayed
while the video is muted or no signal is supplied.
• You can capture the images from the COMPUTER1,
COMPUTER2, DVI, and HDMI input sources.
Setting procedure
INSTALLATION
STANDARD
STANDARD
AUTO POWER
ON
AUTO POWER
OFF
IMAGE CAPTURE
ON
SPLASH SCREEN
To stop the motion in the image temporarily (or to
display a still image):
Press the FREEZE button on the remote control.
• The image will freeze temporarily.
Important:
• Do not display a still picture for a long time
because the afterimages may persist on the screen.
opt.
LAMP MODE
Freeze
To resume the motion in the image:
Press the FREEZE button on the remote control again.
1. Display your desired image.
2. Display the INSTALLATION menu.
3. Select IMAGE CAPTURE by pressing the  or 
button.
STANDBY MODE
• You can’t set IMAGE CAPTURE when PASSWORD
FUNCTION in the FEATURE menu has been set to
SPLASH ID SCREEN to enable the password lock.
OFF
OFF
GO
ON
4. Press the ENTER
button.
BLUE
BACK COLOR
• Image capture
starts and the
captured image is
BLACK
AV MUTE MODE
displayed.
IMAGE REVERSE
OFF
• Once youLENS
press
button, you
LOCK the ENTER OK
cannot use other functions until the capturing
completes.
• When the resolution of the captured image is
lower than 1280 x 800, the image is enlarged to
1280 x 800 when displayed.
• When the resolution of the captured image is
higher than 1280 x 800, only the portion within
the 1280 x 800 range is captured.
Important:
• Images with complicated patterns may not be
captured. In such cases, change the image to be
captured.
• Some images can’t be captured correctly because
of their signal type. For details, see page 50.
• You can’t change the new startup screen back to
the original startup screen. (Even when you select
RESET ALL in the FEATURE menu, the factory
default screen isn’t available any longer.) When you
want to change the startup screen again, capture
another image.
• The captured image will be displayed from the next
startup. If the captured image isn’t displayed, make
sure that the setting of SPLASH SCREEN in the
INSTALLATION menu isn’t OFF. (See page 30.)
• To display the captured image while the video is
muted, set AV MUTE MODE in the INSTALLATION
menu to IMAGE. (See page 30.)
• To display the captured image while no signal is
supplied, set BACK COLOR in the INSTALLATION
menu to IMAGE. (See page 30.)
• In the mute mode, or when no signal is input, it
takes longer time to display the captured image.
EN-37
Advanced features (continued)
Password function
This projector is equipped with the password function
that is designed for prevention of wrong operation by
children and restriction on operation by other than
specified users. The password function has 3 modes
as follows.
DISPLAY INPUT........... When the projector is turned
on, the startup screen (or splash screen) will appear
and stay on the screen until the password is
entered. When the password is entered, the startup
screen will switch to the regular operation screen.
MENU ACCESS............ All the buttons except for the
POWER button on the projector are disabled. (The
buttons on the remote control are enabled.) You
can use this mode as a measure of prevention
of wrong operation by children and restriction on
operation by other than specified users.
SPLASH ID SCREEN.... IMAGE CAPTURE and
SPLASH SCREEN in the INSTALLATION menu
become unavailable. SPLASH SCREEN will be set
to ON automatically.
To enable the password function:
1. Display the FEATURE menu.
2. Press the  or  button to select PASSWORD
FUNCTION.
3. Press the  or  button to change the mode
among DISPLAY INPUT , MENU ACCESS and
SPLASH ID SCREEN .
• When the password has already been set, the
mode won’t be changed. In such cases, press
the ENTER button to cancel the password
function and try again.
4. Press the ENTER button.
• The screen for setting the password function will
appear.
OK
OK
OK
2
O K : ENTER
CANCEL : MENU
5. Enter a 4 - 8 digit password using the , ,  and
 buttons on the remote control as shown below.
(=1, =2, =3, =4)
6. Press the ENTER button.
• If you enter a wrong password, an error
message will appear.
• To cancel the procedure, press the MENU
button.
Important:
• Disable the password by pressing the MENU and
ENTER buttons on the projector at the same time.
CONFIRM
1
O K : ENTER
LOCK
UNLOCK
3
PASSWORD
2
MENU ACCESS
1
5. Press the ENTER button.
• The screen for entering a password will appear.
4
FEATURE
4
MENU ACCESS
UNLOCK
opt.
PASSWORD
FEATURE
OK
To cancel the password function:
1. Display the FEATURE menu.
2. Press the  or  button to select PASSWORD
FUNCTION.
3. Press the ENTER button.
• The screen for canceling the password function
will appear.
4. Press the ENTER button.
• The screen for entering the password will
appear.
opt.
LOCK
8. Enter the password again for confirmation using the
same steps.
9. Press the ENTER button.
• If the entered passwords don’t match, an error
message will appear.
• To cancel the procedure, press the MENU
button.
CANCEL : MENU
3
6. Enter a 4 - 8 digit password using the , ,  and
 buttons on the remote control as shown below.
(=1, =2, =3, =4)
7. Press the ENTER button.
• To cancel the procedure, press the MENU
button.
EN-38
Advanced features (continued)
Mouse remote control
By connecting to personal computer through the USB port, you can operate your computer with the projector remote
control.
Projector + computer with USB connector
USB
USB cable (option)
To USB port
USB 4-pin
(type A)
USB 4-pin
(type B)
• You can use the mouse remote control function with a computer supporting USB only.
• You cannot control Macintosh computers using the remote control.
• When the lamp is turned ON, the computer connected with the USB cable may not work correctly. In this case,
restart the computer.
• When a computer is connected using a long USB cable, it may not be controlled by the remote control correctly.
To extend the cable length, you are recommended to use a repeater.
• You cannot control the computer using the remote control during power standby and for a while after the power is
turned on.
Operation
KEYSTONE
COMPUTER
AUTO POSITION
HDMI
VIDEO
DVI-D(HDCP)
S-VIDEO
LENS SHIFT
LASER
1
2
ZOOM/FOCUS
Mouse pointer
L-CLICK button
Use to move the
cursor on the image,
instead of the
computer mouse.
HOME button
Press to jump back
to the first page.
R-CLICK button
MENU
R-CLICK
ENTER
HOME
PAGE UP
VOLUME
END
PAGE DOWN
ASPECT
CE
END button
Press to jump to the
last page.
AV MUTE
FREEZE
This operates in the same
way as the right button on
the computer mouse.
PAGE UP button
Press to go back to the
previous page.
PAGE DOWN button
Press to go to the next
page.
EN-39
This operates in the
same way as the left
button on the computer
mouse.
Advanced features (continued)
Supervising and controlling by computer
You can supervise and control the projector’s operation using a personal computer via a LAN network.
• To supervise and control the projector, install the software “Projector-Control Device Installer *” contained in the
attached CD-ROM. For the installation procedure and usage of the software, see “User Manual for LAN Control
Utility” contained in the attached CD-ROM.
*) Functions
• Setting of the projector’s IP address
• Setting of password, display language, and LAN control
• PJLink™ certification setting (telnet function)
• Startup of the controlling /supervising tool (ProjectorView) using the Web browser
Major functions
ProjectorView
The controlling /supervising tool using the Web browser
PJLink™
This projector supports standard protocol PJLink™ for projector control and you can control and monitor projector’s
operations using the same application among projectors of different models and different manufacturers.
About PJLink™
• To use PJLink™ function, the PJLink™ application software is required.
• For the specifications of PJLink™, access to the Web site of Japan Business Machine and Information System
Industries Association (JBMIA). (http://pjlink.jbmia.or.jp/english)
• This projector is fully compliant to the specifications of JBMIA PJLink™ Class 1. It supports all the commands
defined by PJLink™ Class 1, and the compliance has been verified with the PJLink™ standard specifications
Version 1.0.
Connection
Computer
LAN cable (option)
(100BASE-TX or 10BASE-T
should be supported.)
To LAN terminal
LAN cable (option)
(100BASE-TX or 10BASE-T should be supported.)
External HUB
• Use a straight-through category-5 cable for LAN connection.
• Don’t touch the metal parts of the LAN connector and LAN cable because static electricity may be discharged
from your body, causing damage to the projector.
Using the User Manual
The User Manual for LAN Control Utility is prepared in the Portable Document Format (PDF) in the CD-ROM.
Opening the User Manual:
1. Load the CD-ROM into the CD-ROM drive.
2. Open CD-ROM “WD3300U.”
3. Double-click on “MANUAL_LAN.HTML” within the CD-ROM. A language selection list for the User Manual will be
displayed.
4. Move the mouse pointer to the desired language and click.
EN-40
Indicators
This projector has 2 indicators, each of which shows the operation condition of the projector.
The following offer solutions to possible problems. If these problems persist, turn the projector off and consult your
dealer.
POWER indicator
STATUS indicator
Normal condition
POWER
STATUS
Off
Steady
red
Blinking
green
Blinking
green
Steady
green
Steady
green
CONDITION
NOTE
Stand-by
Lamp stand-by for power-off
The power cannot be turned on by pressing
the POWER button.
Lamp stand-by for power-on
The power cannot be turned off by pressing
the POWER button.
The power is on. (Normal condition)
Abnormal condition
POWER
STATUS
Steady
green
or
Blinking orange
CONDITION
POSSIBLE SOLUTION
Abnormal temperature
• The ventilation grilles are clogged with dust or dirt.
• The room temperature is high.
• Clean the ventilation grilles.
• Relocate the projector to a cooler place.
Steady
red
The protection circuit is working or the lamp is in an
abnormal condition.
• Wait until the STATUS indicator goes out,
then press the POWER button.
• If the above solution is not effective,
replace the lamp.
Blinking green/red
Lamp operation time warning. (Total lamp operation
time reached 3000 hours*1 while the power was on.)
Blinking red
Lamp operation time warning. (Total lamp operation
time reached 3000 hours*1 while the power was off.)
Replace the lamp.
Change with a new lamp if this problem
recurs.
Steady red
Lamp operation time warning. (Total lamp operation
time reached 4000 hours*1*2 while the power was off.)
Steady
red
Blinking green
Steady
green
Steady
red
Blinking
green/red
Steady
or
Abnormal.
Contact your dealer.
Blinking
*1: Duration when LAMP MODE of the INSTALLATION menu is set to LOW. When it is set to STANDARD, this duration will be
shorted.
*2: When LAMP MODE is set to STANDARD, this duration will be shorted up to 2000 hours.
EN-41
Replacing the lamp
This projector is equipped with a lamp to project images. This lamp is a consumable. It may burn out or its brightness
may decrease during use. In such cases, replace the lamp with a new one as soon as possible. Be sure to replace the
lamp with a new lamp separately sold that is exclusive to this projector. Contact your dealer for purchase of the lamp.
Spare lamp
VLT-XD3200LP
Warning:
• Be careful not to drop the lamp fixing screws into the inside of the projector. Don’t put a metal piece or flammable
object into the projector. Using the projector with any foreign object present inside may result in electric shock or
fire. When you can’t remove the foreign object from the inside, contact your dealer for removal.
• Be sure to install the lamp securely. When the lamp isn’t installed properly, it won’t illuminate. Improper installation
may also result in fire.
• Don’t shake the removed lamp or don’t lift it above your face. You may be injured in your eye by flying or falling
glass fragments.
• Don’t replace the lamp immediately after use because the lamp cover is very hot. You may get burned. Turn off the
power using the POWER button. After the lamp goes out, wait about 2 minutes until the intake and exhaust fans
for cooling the lamp stop rotating. Then turn off the main power switch, unplug the power cord, and wait at least 1
hour to allow the lamp to cool down enough to the touch.
• Do not touch the lamp directly. It may break and cause injury or burn.
Interval of lamp replacement
The recommended interval of lamp replacement is about 4000 hours*1*2 of consecutive use. Such interval differs
depending on the operating environment and may be shorter than 4000 hours*1*2. Decrease in luminescence and/or
color brightness indicates that the lamp needs to be replaced. When the lamp operation time exceeds 3000 hours*1,
the indicator will blink alternately between green and red (while the lamp is lit; when the lamp is not lit, the indicator
will be lit red only) and the lamp replacement message will appear on the screen for 1 minute everytime the lamp
is turned on. When the lamp has been used for about 3800 hours*1, the replacement message (LAMP EXCHANGE)
will appear on the screen for 1 minute every 20 hours*1 thereafter. When the lamp operation time exceeds 4000
hours*1*2, the projector automatically shuts off and can’t be used until the lamp is replaced and the lamp
operation time is reset.
*1: Duration when LAMP MODE of the INSTALLATION menu is set to LOW. When it is set to STANDARD, this duration will be
shorted.
*2: When LAMP MODE is set to STANDARD, this duration will be shorted to 2000 hours.
Caution:
• Don’t remove the lamp for any purpose other than replacement. Unnecessary removal of the lamp may result in a
breakdown.
• This projector uses a high-pressure mercury lamp as the light source. The high-pressure mercury lamp may
explode or fail to illuminate permanently because of an impact, scratch, or deterioration through use. The period
of time until explosion or permanent failure to illuminate varies considerably from lamp to lamp, depending on
operation conditions. Therefore, the lamp may explode soon after the start of use.
• The possibility of explosion of the lamp increases if you use it beyond its replacement period. When the instruction
of lamp replacement appears, replace it with a new one immediately even if the lamp is still lighting normally.
• When the high-pressure mercury lamp explodes, glass fragments will scatter inside or outside the lamp box and
the gas charged inside the lamp will diffuse inside or outside the projector. The gas inside the lamp contains
mercury. Be careful not to breathe it or avoid it from entering your eye or mouth. If you should breathe it or if it
should enter your eye or mouth, see a doctor immediately.
• In the event that the high-pressure mercury lamp exploded, glass fragments may have been scattered inside the
projector. Ask your dealer to replace the lamp and to inspect the inside of the projector. When you clean or replace
the lamp by yourself, be sure to hold the handle of the lamp. You may get injured by glass fragments.
• When removing the lamp from the ceiling-mounted projector, use the lamp replacement tray packed with the
projector or option lamp to prevent glass fragments from scattering.
• Be sure to use the lamp exclusive to this projector, VLT-XD3200LP. Use of other lamps may cause a failure of the
projector.
EN-42
Replacing the lamp (continued)
To replace the lamp:
8. Tighten up the screws (c) using a Phillips
screwdriver (+).
1. Turn off the main power switch and unplug the
power cord.
2. Loosen the screw (a) using a Phillips screwdriver
(+), and remove the lamp cover (b).
(c)
(a)
9. Tighten up the screw (a) using a Phillips screwdriver
(+) to secure the lamp cover (b).
(b)
3. Loosen the screws (c) using a Phillips screwdriver
(+).
(a)
(b)
Reset of the lamp operation time
10.Plug the power cord into the wall outlet and turn on
the main power switch.
11.Press the t, , and POWER button on the
projector at the same time.
(c)
4. Pull the handle.
5. Pull out the lamp box by the handle while holding
the projector.
Important:
• Unless these 3 buttons are pressed at the same
time, the lamp operation time isn’t reset.
• Make sure that the STATUS indicator blinks twice
and the lamp operation time is reset successfully.
• The projector doesn’t turn on if the lamp cover isn’t
attached securely.
• Be sure to reset the lamp operation time whenever
you replace the lamp.
• Do not reset the lamp operation time unless you
replace the lamp.
• The lamp is fragile. If it is broken, be careful not to
cut yourself with glass fragments.
• Pull the lamp box out of the projector slowly.
If it is pulled out quickly, the lamp may break
scattering glass fragments.
• Do not spill liquid on the removed lamp box or
do not place it near any flammable object or
where children can reach to prevent injury or
fire.
6. Load a new lamp box securely into the projector in
the right orientation.
Caution:
• This projector uses a lamp that
contains mercury. Disposal of the lamp
or the projector with the lamp may
be regulated due to environmental
considerations. For disposal or
recycling information, please contact
your local authorities or the Electronic
Industries Alliance: www.eiae.org. (For
the U.S. only.)
7. Put the handle back to the original position.
• Make sure that the handle is locked.
EN-43
Replacing the lamp (continued)
When removing the lamp from the ceiling-mounted projector
When removing the lamp from the ceiling-mounted projector, use the lamp replacement tray packed with the
projector or option lamp to prevent glass fragments from scattering.
• Assemble the lamp replacement tray according to the procedure shown on it.
1. Follow steps 1 to 4 on page 43.
2. Attach the lamp replacement tray to the projector as shown in the
figure.
3. Secure the lamp replacement tray on the projector using the tape
packed with the tray.
Tape
4. Pull out the lamp box by the handle while holding the projector.
• Hold the lamp replacement tray to prevent glass fragments
from scattering.
• Don’t put the lamp directly on the lamp replacement tray
because it may fall.
5. Detach the lamp replacement tray together with the removed
lamp.
6. Follow steps 6 to 11 on page 43.
Maintenance
Warning:
• Do not use flammable solvents (benzene, thinner, etc.) and flammable aerosols when cleaning the projector body
and lens. Flammable substances may ignite causing fire or breakdown while the lamp is illuminating.
Caution:
• Be sure to turn off the lamp and unplug the power cord from the wall outlet before you perform any maintenance
on the projector.
Cleaning of the projector and the ventilation slots
Use a soft cloth to clean the projector and the ventilation grilles. When the grilles become dirty, wipe them with a soft
cloth dampened with diluted mild detergent, and then wipe them with a dry cloth.
• Clean the inside of the terminal cover frequently as dust is apt to be collected.
To protect the surface of the projector from fading or deteriorating:
• Do not spray insecticide on or inside the projector.
• Do not use benzine or thinner to clean it.
• Do not let rubber or plastic materials contact with projector.
Cleaning of the lens
Use a standard lens-cleaning brush or a piece of lens tissue dampened with lens cleaning fluid. The lens surface is
fragile. Use only recommended, nonabrasive lens-cleaning materials. Do not touch the lens with your fingers.
EN-44
Troubleshooting
Before asking for repair of the projector, check the following. If the symptom persists, stop using the projector, be
sure to unplug the power plug, and then contact your dealer.
No image appears on the screen.
Problem
Solution
Power can not be
turned on.
• Check whether the indicators are on or off and how they are lightning.
POWER STATUS Solution
• Connect the power cord to the projector.
• Plug the power cord into a wall outlet.
Off
Off
• Turn on the main power swich.
• Attach the lamp cover.
• If any objects are blocking the air inlet or outlet grille, remove them and carry out
the following.
Off
Steady red
Blinking
orange
1. Turn off the main power swich.
2. Make sure that the projector has cooled off.
3. Turn on the main power swich.
4. Press the POWER button.
• If any objects are blocking the air inlet or outlet grille, remove them.
• Don’t expose the air outlet grilles to hot air emitted from a heating appliance.
• After the STATUS indicator stops blinking, press the POWER button.
Blinking
green
Steady red
• If the main power switch is turned off while the fan is rotating, the lamp may not turn on
about 2 minutes when the main power switch is turned on next time.
• The lamp can’t turn on again for 2 minutes after it goes out.
• Press the POWER button several times.
• Replace the lamp. (The lamp is at the end of its life.)
• Unplug the power cord from the wall outlet and contact your dealer.
Blinking
red/green
No image appears on
the screen.
•
•
•
•
•
•
•
•
•
Steady
or
Blinking
Cancel the AV mute by pressing the AV MUTE button.
Check that the lens cap is removed.
It may take about 1 minute for the lamp to light up.
The lamp fails to light up on rare occasions. In such a case, wait for a few minutes
and then try again.
If the projector was turned off before the lamp was cooled down sufficiently last time,
the fan may start rotating and the POWER button may not work after the main power
switch is turned on. After the fan stops rotating, press the POWER button to turn back
on the POWER indicator.
Set SCART INPUT in the QUICK MENU or FEATURE menu to OFF. (See pages 27 and
31.)
Check that the intake vent is clean.
Check that the cables connected to the external devices are not broken.
When an extension cable is being used, replace it with the supplied cable for check.
When images are displayed correctly, add an RGB signal amplifier to the extension
cable.
Power turns off.
• This problem may occur when the intake vent and/or exhaust vents are blocked. (In
such a case, the STATUS indicator brinks orange.)
 Remove the objects blocking the intake vent and/or exhaust vents and then carry
out the following procedure.
1. Wait for the intake fan and/or exhaust fan to stop. (Wait until the STATUS indicator
goes out.)
2. Turn off the main power switch.
3. Wait about 10 minutes.
4. Turn on the main power switch.
5. Press the POWER button.
• When the STATUS indicator is steady red, it is indicating that the lamp should be
replaced. Replace the lamp in this case.
• Check that AUTO POWER OFF has been set to OFF.
• If the lamp has deteriorated, it may go out after a while it illuminates.
The screen for
entering the password
appears.
• PASSWORD FUNCTION in the FEATURE menu has been set to DISPLAY INPUT
enable the password lock.
 Enter the password or contact the person in charge of management of the
projector. (See page 38.)
EN-45
to
Troubleshooting (continued)
No image appears on the screen. (continued)
Problem
Solution
“NO SIGNAL” is
displayed.
• Turn on the power of the connected device, or check whether there is something
wrong with the connected device.
• Check whether the external device output signals. (Check this especially when the
external device is a notebook computer.)
• Check that the cable connected to the external device isn’t defective.
• Check that the projector is connected to the external device using the correct terminals.
• Check that the connected device is correctly selected as the input source.
• When an extension cord is being used, replace it with the supplied cable and check
whether images are projected correctly. If images are projected correctly, use an RGB
signal amplifier along with the extension cord.
Images are not displayed correctly.
Problem
Solution
Projected images are
shaking.
Projected images are
displaced.
• Check that the cable connected to the external device isn’t intermittent.
• Connect the cable’s plug with the external device’s connector firmly.
• Project an image containing many characters such as a help menu and press the
AUTO POSITION button.
• Some computers output out-of-spec signals on rare occasion. Adjust the SIGNAL
menu. (See pages 35 and 36.)
Projected images are
distorted.
• Adjust the projector and the screen so that they are perpendicular to each other. (See
page 11.)
Projected images are
dark.
• Adjust BRIGHTNESS and CONTRAST in the QUICK MENU or IMAGE menu. (See
page 33.)
• Replace the lamp. (See page 42.)
Projected images are
blurred.
•
•
•
•
•
White dots are seen
on projected images.
Black dots are seen
on projected images.
• This symptom is normal for a DLP™ projector and is not a malfunction. (A very small
number of pixels may stay lit or out, but such symptom is not a malfunction. Pixels of
99.99% or more are effective.)
Rainbow effect is seen
on projected images.
• This is due to color breaking noise that occurs in a DLP™ system and is not a
malfunction.
Fine streaks are seen
on projected images.
• This is due to interference with the screen surface and is not a malfunction. Replace
the screen or displace the focus a little.
• Vertical or horizontal streak noise may appear on the projected image, depending on
the type of the DVD player or game console you use. In such a case, you can reduce
such streak noise by enabling the LPF.
Projected images
become wavy.
• Connect the plugs of the cables to external devices securely.
• Keep the projector away from devices that emit interfering radio waves.
• When the keystone adjustment is carried out, the image may not be displayed
correctly depending on the type of input signal. This isn’t a product malfunction. In
this case, readjust the keystone so that the amount of keystone correction is as small
as possible.
Hue is not appropriate.
• Check that the cables connected to the external devices are not broken.
Tint in projected
images is incorrect.
• Check that COMPUTER INPUT in the SIGNAL menu is correctly set. (See page 32.)
• Check that the cable connected to the external device isn’t broken.
Adjust the focus. (See pages 16 and 23.)
Clean the lens.
Press the  or  button on the remote control to eliminate flicker.
Adjust TRACKING and FINE SYNC. in the SIGNAL menu. (See page 36.)
Adjust BRIGHTNESS and CONTRAST in the QUICK MENU or IMAGE menu. (See
page 33.)
• Adjust the projector and the screen so that they are perpendicular to each other. (See
page 11.)
EN-46
Troubleshooting (continued)
Images are not displayed correctly. (continued)
Problem
Solution
Different color tint.
• When comparing images projected by two projectors, tints in the displayed images
may be different because of variation between their optical components. This is not a
malfunction.
• When comparing the image projected by this projector with those displayed on the
television or PC monitor, tints in the displayed images may be different because of
difference in the range of color reproducibility. This is not a malfunction.
Only the motion areas
in the images supplied
from the computer
aren’t displayed.
• This is caused by the computer being used. Contact the manufacturer of your
computer.
Projected images are
obscured.
• Match the output resolution of your computer with the resolution of the projector.
For the method to change the output resolution of the computer, contact the
manufacturer of your computer. (See page 50.)
• Some images and texts appear obscured during the keystone adjustment. In such
cases, use the projector without applying the keystone adjustment. (See page 11.)
Noise appears around
the image.
• In some images such as DVD, noise may appear around the recorded image. In this
case, decrease the setting value of OVER SCAN of the SIGNAL menu. (See page 32.)
Images of WXGA
signal are not
displayed correctly.
• Make adjustment according to “How to adjust the computer image” on page 35.
Others
Problem
Solution
The exhaust vents
emit warm air.
• This air comes out after cooling the inside of the projector. You may feel hot, but this
is not a malfunction.
No audio is output.
• Check that the volume isn’t set to low.
• When the external device is connected with an HDMI cable, set the audio output of
the device to PCM output.
The menu can’t be
used.
• The microcomputers inside the projector may be wrongly operating because of noise.
 Turn off the main power, wait about 10 minutes, and turn on the main power again.
“TEMPERATURE!!” is
displayed.
• This indication appears when the ambient temperature rises high. When the ambient
temperature stays high, the lamp goes out.
 Eliminate any causes of the rise in the ambient temperature.
• This indication appears when the air inlet or outlet grille is blocked. When they are
kept blocked, the lamp goes out.
 Remove the objects blocking the air inlet or outlet grille.
The
• This mark appears when ineffective operation is carried out. This isn’t a product
malfunction.
mark appears.
The remote control
doesn’t function easily
or at all.
• Check that the batteries are loaded in the remote control or the batteries are not
weak. (See page 6.)
• Check that the remote control sensor isn’t exposed to direct sunlight or fluorescent
light. (See page 9.)
• Use the remote control within its operation range. (See page 9.)
• Use the remote control at least 10 cm away from the projector.
The buttons on the
projector (except for
the POWER button)
don’t function.
• PASSWORD FUNCTION in the FEATURE menu has been set to MENU ACCESS to
enable the password lock.
 Cancel the password lock or contact the person in charge of management of the
projector. (See page 38.)
Abnormal sound is
heard.
• Because the color wheel spins at a high speed, metallic sounds may be heard in rare
occasions. Such symptom is not a malfunction.
EN-47
Troubleshooting (continued)
If the following problem occurs after the lamp is replaced, check the following first.
Problem
Solution
The projector does not
turn on.
• Fit the lamp cover securely. (See pages 42 and 43.) • Reset the lamp operating time. (See page 43.)
The STATUS indicator
blinks.
• Reset the lamp operating time. (See page 43.)
Kensington Lock
This projector has a Kensington Security Standard connector for use with Kensington MicroSaver Security System.
Refer to the information that came with the Kensington System for instructions on how to use it to secure the
projector. Please contact Kensington Technology Group below.
Kensington Technology Group
2855 Campus Drive
San Mateo, CA 94403, U.S.A.
Phone: +1- (650)572-2700
Fax: +1- (650)572-9675
EN-48
Specifications
The specifications and outside appearance of the projector are subject to change without prior notice.
Type
Model
Display technology
Projection lens
Light-source lamp
Image size (projection distance)
Maximum resolution Computer signal
Video signal
Component signal
Computer/component video input
Video input
Audio input
HDMI input
Monitor output
Audio output
Speaker
Control terminal/others
Operating temperatures
Rated voltage
Power consumption
Dimensions (not includeing protrusion)
Weight
Others
S-video input
Video input
Component video
input
Analog input
Digital input (DVI)
Digital input (HDMI)
Audio input
DC OUT
DLP™ projector
WD3300U
0.65-inch Single chip DMD
Pixel 1280 x 800 = 1024000 pixels
F 2.0 - 2.4 f= 24.5 - 33.1 mm
330 W
40” min. to 300” max. (projection distance 1.5 to 11.4 m)
Maximum resolution: 1600 x 1200 dots (compressed)
Panel resolution: 1280 x 800 dots
NTSC/PAL/SECAM/4.43NTSC/PAL-M/PAL-N/PAL-60
480i, 480p, 576i, 576p, 720p, 1080i, 1080p
Panel resolution: 1280 x 800 dots
[Signal type]
[Terminal type]
[Line]
Analog RGB
Mini D-SUB 15-pin
1
Analog RGB
5 BNC
1
Digital RGB
DVI-D 24-pin
1
[Signal type]
[Terminal type]
[Line]
Video input
RCA / BNC
1
S-video input
S / 2 BNC
1
[Signal type]
[Terminal type]
[Line]
RGB/Component
Stereo mini jack (ø3.5)
2
Digital RGB
Stereo mini jack (ø3.5)
1
Video
RCA (L, R)
1
S-video
RCA (L, R)
1
[Signal type]
[Terminal type]
[Line]
HDMI
HDMI 19-pin
1
[Signal type]
[Terminal type]
[Line]
Analog RGB
Mini D-SUB 15-pin
1
[Signal type]
[Terminal type]
[Line]
RGB/Component
Stereo mini jack (ø3.5)
1
10 W Mono Round type ø4.5 cm x 1
RS-232C (D-SUB 9-pin), USB, LAN (RJ-45), REMOTE IN/OUT
+41°F (+5°C) to +95°F (+35°C) AC 100 - 240 V, 50/60 Hz
4.5 A, 430 W
During standby:
AC 100 - 120 V: 2 W (when STANDBY MODE is STANDARD)
0.4 W (when STANDBY MODE is LOW)
AC 220 - 240 V: 2 W (when STANDBY MODE is STANDARD)
0.6 W (when STANDBY MODE is LOW)
450 mm (W) x 187 mm (H) x 373 mm (D) (projector only)
450 mm (W) x 187 mm (H) x 468 mm (D) (including the terminal cover)
10.3 kg (projector only), 10.5 kg (including the terminal cover)
Luminance signal: Vp-p=1.0 V 75 Ω (negative sync)
Chrominance signals: Vp-p=0.286 V 75 Ω (burst signal)
Vp-p=1.0 V 75 Ω (negative sync)
YCBCR:Vp-p=1.0 V 75 Ω (Y) (negative sync)
Vp-p=0.7 V 75 Ω (CB, CR)
RGB: Vp-p=0.7 V 75 Ω (negative sync)
YCBCR: Vp-p=1.0 V (Y) (negative sync) Vp-p=0.7 V (CB, CR)
HD/CS: TTL-level (negative or positive polarity)
VD: TTL-level (negative or positive polarity)
DVI-D interface (TMDS single link) with HDCP
HDMI interface (TMDS single link) (Only PCM audio is supported.)
350 mVrms, 10 kΩ or more
5 V 1.5 A (max)
Replacement part (option/not included in the box)
Spare lamp: VLT-XD3200LP
Option lenses: OL-XD2000SZ, OL-XD2000LZ, OL-XD2000TZ, OL-XD2000FR
EN-49
Specifications (continued)
Specification of RGB signals in each computer mode of the projector
Signal mode
TV60, 480i (525i)
TV50, 576i (625i)
1080i60 (1125i60)
1080i50 (1125i50)
480p (525p)
576p (625p)
720p60 (750p60)
720p50 (750p50)
1080p60 (1125p60)
1080p50 (1125p50)
CGA70
CGA84
CGA85
VGA60
VGA72
VGA75
VGA85
SVGA56
SVGA60
SVGA72
SVGA75
SVGA85
SVGA95
XGA60
XGA70
XGA75
XGA85
SXGA70a
SXGA75a
SXGA85a
WXGA60
WXGA60a
WXGA60b
WXGA60c
WXGA+60
SXGA60b
SXGA75b
SXGA85b
SXGA60
SXGA75
SXGA85
SXGA+60
SXGA+75
WSXGA+60
MAC13
MAC16
MAC19
HP75
HP72
SUN66a
SUN76a
SUN66
SUN76
SGI72
SGI76
UXGA60
Resolution
(H x V)
640 x 400
640 x 400
640 x 400
640 x 480
640 x 480
640 x 480
640 x 480
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1152 x 864
1152 x 864
1152 x 864
1280 x 768
1280 x 800
1360 x 768
1366 x 768
1440 x 900
1280 x 960
1280 x 960
1280 x 960
1280 x 1024
1280 x 1024
1280 x 1024
1400 x 1050
1400 x 1050
1400 x 1050
1680 x 1050
640 x 480
832 x 624
1024 x 768
1024 x 768
1280 x 1024
1152 x 900
1152 x 900
1280 x 1024
1280 x 1024
1280 x 1024
1280 x 1024
1600 x 1200
Horizontal
frequency (kHz)
15.73
15.63
33.75
28.13
31.47
31.25
45.00
37.50
67.50
56.25
31.47
37.86
37.86
31.47
37.86
37.50
43.27
35.16
37.88
48.08
46.88
53.67
59.97
48.36
56.48
60.02
68.68
63.85
67.50
77.49
47.78
49.70
47.71
47.50
55.94
60.00
75.00
85.94
63.98
79.98
91.15
63.98
65.32
82.28
65.29
35.00
49.72
60.24
62.94
78.13
61.85
71.81
71.68
81.13
76.92
82.01
75.00
Vertical frequency
(Hz)
59.94
50.00
60.00
50.00
59.94
50.00
60.00
50.00
60.00
50.00
70.09
84.13
85.08
59.94
72.81
75.00
85.01
56.25
60.32
72.19
75.00
85.06
94.89
60.00
70.07
75.03
85.00
70.01
75.00
85.06
59.87
59.81
60.02
59.75
59.89
60.00
75.00
85.00
60.02
75.02
85.02
60.02
59.98
74.87
59.95
66.67
74.55
75.02
74.92
72.00
66.00
76.64
66.68
76.11
72.30
76.00
60.00
Normal mode
(H x V)
1066 x 800
1066 x 800
1280 x 720
1280 x 720
1066 x 800
1066 x 800
1280 x 720
1280 x 720
1280 x 720
1280 x 720
1280 x 800
1280 x 800
1280 x 800
1066 x 800
1066 x 800
1066 x 800
1066 x 800
1066 x 800
1066 x 800
1066 x 800
1066 x 800
1066 x 800
1066 x 800
1066 x 800
1066 x 800
1066 x 800
1066 x 800
1066 x 800
1066 x 800
1066 x 800
1280 x 768
1280 x 800
1280 x 720
1280 x 720
1280 x 800
1066 x 800
1066 x 800
1066 x 800
1000 x 800
1000 x 800
1000 x 800
1066 x 800
1066 x 800
1066 x 800
1280 x 800
1066 x 800
1066 x 800
1066 x 800
1066 x 800
1000 x 800
1024 x 800
1024 x 800
1000 x 800
1000 x 800
1000 x 800
1000 x 800
1066 x 800
*1: IMAGE CAPTURE in the INSTALLATION menu doesn’t function with these signals.
*2: The COMPUTER/COMPONENT VIDEO DVI-D IN (HDCP) terminal is available for these signals.
*3: The HDMI IN terminal is available for these signals.
EN-50
Real mode
(H x V)
640 x 400
640 x 400
640 x 400
640 x 480
640 x 480
640 x 480
640 x 480
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1152 x 800
1152 x 800
1152 x 800
1280 x 768
1280 x 800
1280 x 768
1280 x 768
1280 x 800
1280 x 800
1280 x 800
1280 x 800
1280 x 800
1280 x 800
1280 x 800
1280 x 800
1280 x 800
1280 x 800
1280 x 800
640 x 480
832 x 624
1024 x 768
1024 x 768
1280 x 800
1152 x 800
1152 x 800
1280 x 800
1280 x 800
1280 x 800
1280 x 800
1280 x 800
*1
*1
*1, *2, *3
*1, *2, *3
*1, *2, *3
*1, *2, *3
*1, *2, *3
*1, *2, *3
*1, *2, *3
*1, *2, *3
*2, *3
*2, *3
*2, *3
*2
*2
*2, *3
*2, *3
*2, *3
Specifications (continued)
Specification of RGB signals in each computer
mode of the projector (continued)
• This projector doesn’t support 480p signals from
video devices having 4 lines (R, G, B, CS*) or having 5
lines (R, G, B, H, V).
* : Composite Sync
Important:
• Some computers aren’t compatible with the
projector.
• The projector’s maximum resolution is 1280 x
800 pixels. It may not display images of higher
resolutions than 1280 x 800 correctly.
• Images with SYNC on G (Green) signal may jitter.
• Images with SYNC on G (Green) signal may be
tinged with green.
• If the resolution and frequency of your computer
aren’t shown on the table, find the compatible
resolution and frequency by changing the resolution
of your computer.
• TV60 and TV50 are equivalent to 480i and 576i
respectively. When these signals are supplied to the
VIDEO IN or S-VIDEO IN terminal, the signal mode is
indicated as TV60 or TV50. When they are supplied to
the COMPUTER/COMPONENT VIDEO IN terminals,
the signal mode is indicated as 480i or 576i.
Connectors
SERIAL (D-SUB 9-pin)
5
COMPUTER/COMPONENT VIDEO COMPUTER/COMPONENT VIDEO
IN-1 (Mini D-SUB 15-pin)
DVI-D IN (HDCP) (DVI-D 24-pin)
5
1
9
Name
I/O
1
2
3
4
5
6
7
8
9
–
TXD
RXD
–
GND
–
–
–
–
–
IN
OUT
–
–
–
–
–
–
1
24
10
6
Pin No.
REAL mode
When moire patterns or lines of uneven thickness
appear on the projected image, these symptoms may
be improved by displaying it in its original image size
(REAL mode). To display the image in the REAL mode,
set ASPECT of the QUICK MENU or the FEATURE
menu to REAL. (See page 26 for menu setting.)
• For signals that are larger than the panel resolution,
only their center part is displayed in the REAL
mode. The area exceeding the panel resolution isn’t
displayed.
• In the REAL mode, images are black-framed
when the image resolution is lower than the panel
resolution.
6
15
9
8
Spec.
DDC 5V
GND
GND
DDC Data
HD/CS
VD
DDC Clock
1 19
17
16
11
Pin No.
Spec.
Pin No.
1
R(RED)/PR/CR
9
2
G(GREEN)/Y
10
3
B(BLUE)/PB/CB 11
4
GND
12
5
GND
13
6
GND
14
7
GND
15
8
GND
Pin No.
1
2
3
4
5
6
7
8
9
10
11
12
HDMI IN
(HDMI 19-pin)
2 18
1
Spec.
Pin No.
TMDS DATA 213
TMDS DATA 2+ 14
TMDS DATA 2 Shield 15
16
17
DDC Clock
18
DDC Data
19
20
TMDS DATA 121
TMDS DATA 1+ 22
TMDS DATA 1 Shield 23
24
Spec.
+5V Power
Ground (for +5V)
Hot Plug Detect
TMDS DATA 0TMDS DATA 0+
TMDS DATA 0 Shield
TMDS Clock Shield
TMDS Clock+
TMDS Clock-
Pin No.
Spec.
Pin No.
Spec.
1
2
3
4
5
6
7
8
9
10
TMDS Data2+
TMDS Data2 Shield
TMDS Data2TMDS Data1+
TMDS Data1 Shield
TMDS Data1TMDS Data0+
TMDS Data0 Shield
TMDS Data0TMDS Clock+
11
12
13
14
15
16
17
18
19
TMDS Clock Shield
TMDS ClockCEC
–
SCL
SDA
DDC Ground
+5 V Power
Hot Plug Detect
Dimension drawings (unit: mm)
Without terminal cover
450
187
101*
101*
187
With terminal cover
373
450
*: Factory-defaults
EN-51
468
MITSUBISHI ELECTRIC CORPORATION
1 Zusho Baba, Nagaokakyo-City, Kyoto Japan
A