Miller Electric MPS-10T Specifications

OM-235 369A
2009−11
®
Auto-Darkening Helmets
Model: CoolBandtIntegrated
Headgear Cooling System
To help us serve you better, go to www.MillerWelds.Com/HelmetReg/
TABLE OF CONTENTS
SECTION 1 − HELMET COOLER SAFETY PRECAUTIONS − READ BEFORE USING . . . . . . 1
1-1. Symbol Usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1-2. Hazards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
SECTION 2 − BATTERY SAFETY PRECAUTIONS − READ BEFORE USING . . . . . . . . . . . . . . 3
2-1. Symbol Usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2-2. Hazards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
SECTION 3 − HEADGEAR COOLING SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
3-1. Helmet Cooling System Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3-2. Installing Headgear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3-3. Installing Head Shroud . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3-4. Charging The Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3-5. Installing The Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
3-6. Installing The Air Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
3-7. Removing Air Deflector To Adjust Air Flow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
3-8. Operating The Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
3-9. Checking The Helmet Cooling System Before Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
3-10. Operating Helmet Cooling System On 120 Volt AC Power . . . . . . . . . . . . . . . . . . . . . . . 14
SECTION 4 − MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
4-1. Adjusting Headgear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
4-2. Replacing Fabric Headband . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
4-3. Maintenance And Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
4-4. Helmet Cooling System Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
SECTION 5 − PARTS LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
SECTION 6 − LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
SECTION 1 − HELMET COOLER SAFETY PRECAUTIONS −
READ BEFORE USING
Protect yourself and others from injury — read and follow these precautions.
1-1. Symbol Usage
Helmet Cooler 2009−11
DANGER! − Indicates a hazardous
situation which, if not avoided, will
result in death or serious injury. The
possible hazards are shown in the
adjoining symbols or explained in
the text.
. Indicates special instructions.
Indicates a hazardous situation
which, if not avoided, could result in
death or serious injury. The possible
hazards are shown in the adjoining
symbols or explained in the text.
This group of symbols means Warning! Watch
Out! ELECTRIC SHOCK, MOVING PARTS,
and HOT PARTS hazards. Consult symbols
and related instructions below for necessary
actions to avoid the hazards.
NOTICE − Indicates statements not related to
personal injury.
1-2. Hazards
Only qualified persons should install, operate, maintain, and repair this unit.
READ INSTRUCTIONS.
D Read and follow all labels and the Owner’s Manual carefully before installing,
operating, or servicing unit. Read the safety information at the beginning of
the manual and in each section.
D Use only genuine replacement parts from the manufacturer.
D Perform maintenance and service according to the Owner’s Manuals, industry standards,
and national, state, and local codes.
HELMET COOLER MISUSE can be hazardous.
Welding produces fumes and gases. Breathing these fumes and gases can be hazardous to your health.
D Read and follow these instructions and the safety labels carefully. This
product is intended for use as a cooling device only. It is not a respiratory protective device and
does not protect the user from airborne contaminants. Have an industrial hygienist test the air in
your facility to determine if respiratory protection is required to provide adequate protection from
contaminants in your environment. With cooling system-equipped helmet on your head and cooling system operating, also test the air inside the helmet to determine if respiratory protection is required. If you have questions about the type of respiratory protection equipment required, consult
your safety director and an Industrial Hygienist.
D Do not use this product where there is danger of fire or explosion.
D Do not use this product in windy conditions or negative pressure inside the hood may draw in
contaminants from the outside air.
D Do not use this product without a properly installed spark guard unless the unit is designed and
intended to be used without one. Without the spark guard (on applicable products), welding
sparks may ignite the filter or damage the filter.
D This product does not supply oxygen. Do not use this product where oxygen levels are 19.5% or
lower, where contaminant levels are unknown or are immediately dangerous to life or health
(IDLH), or where the contaminant levels exceed the equipment specifications.
D Do not enter a work area until you are sure the equipment is correctly assembled, working properly, and properly worn.
OM-235 369 Page 1
D Before each use, inspect the equipment for damage and verify it operates properly.
D Dangerous contaminants may not smell or be visible. Leave the area immediately if you notice
the following:
. . . Breathing becomes difficult.
. . . You experience dizziness, impaired vision, or eye, nose, or mouth irritation.
. . . The equipment is damaged.
D Do not repair, modify, or disassemble this product or use with parts or accessories not supplied by
the manufacturer.
D Do not operate unit without properly installed filter(s). Replace damaged or clogged filters. Do not
wash or reuse filters. Do not clean filters by tapping or with compressed air or filter elements may
be damaged.
D Do not restrict or alter helmet cooler air flow. Do not block air inlet or outlet. Be sure safety
glasses, hair, weld cap, and other objects do not block air flow.
D This product contains electrical parts which have not been evaluated as an ignition source in
flammable or explosive atmospheres by MSHA/NIOSH.
OM-235 369 Page 2
SECTION 2 − BATTERY SAFETY PRECAUTIONS −
READ BEFORE USING
Protect yourself and others from injury — read and follow these precautions.
2-1. Symbol Usage
Small Batt 2009−11
DANGER! − Indicates a hazardous
situation which, if not avoided, will
result in death or serious injury. The
possible hazards are shown in the
adjoining symbols or explained in
the text.
. Indicates special instructions.
Indicates a hazardous situation
which, if not avoided, could result in
death or serious injury. The possible
hazards are shown in the adjoining
symbols or explained in the text.
This group of symbols means Warning! Watch
Out! ELECTRIC SHOCK, MOVING PARTS,
and HOT PARTS hazards. Consult symbols
and related instructions below for necessary
actions to avoid the hazards.
NOTICE − Indicates statements not related to
personal injury.
2-2. Hazards
Only qualified persons should install, operate, maintain, and repair this unit.
FIRE OR BATTERY EXPLOSION hazard.
During operation keep everyone, especially children, away.
Do not install or place charger on, over, or near combustible surfaces.
Do not charge battery near flammables.
Examine the battery before first use. Return battery to the manufacturer if battery is damaged, dirty, or emits an unusual odor.
D Use battery only with equipment with which it was supplied. Replace battery
only with battery specified in Owner’s Manual. Use of another battery may
present a risk of fire or explosion.
D Keep battery dry.
D
D
D
D
D Do not use or store the battery in extremely hot or humid conditions. See the Owner’s Manual
for specific operating and storage information.
D Keep battery away from fire, out of direct sunlight, and away from other sources of heat.
D Do not use or charge the battery if it has been dropped or damaged.
D Do not open, puncture, repair, disassemble, or modify the battery.
D Charge battery only with supplied charger in an open, well−ventilated location out of direct sunlight and according to supplied instructions.
D Do not overcharge a battery or charge battery longer than specified (if charger is not equipped
with automatic shutoff). See the Owner’s Manual for specific information on battery charging.
D Do not charge battery by connecting directly to AC receptacle. Do not connect battery charger
to automobile auxiliary power receptacle.
D Do not connect (short circuit) battery terminals to each other. Do not allow tools, conductive
materials, or other objects to touch both battery terminals at the same time.
D Do not weld on battery or fasten any objects to battery.
D Do not heat battery in a microwave oven or any other heating device.
D Keep battery away from sources of high voltage.
D Do not expose battery to static electricity.
D Do not use or mix battery with damaged or worn out batteries, or other types of batteries.
OM-235 369 Page 3
BATTERY ACID can BURN SKIN and EYES.
D Replace damaged battery.
D Do not touch materials from inside a damaged battery.
D Flush eyes and skin immediately with water.
READ INSTRUCTIONS.
D Read and follow all labels and the Owner’s Manual carefully before before
using the battery or battery charger. Read the safety information at the beginning of the manual and in each section.
D Dispose of battery according to local, state, and federal requirements. Do not dispose of battery in fire or water.
D Contact the equipment manufacturer if you have any questions about the battery.
OM-235 369 Page 4
SECTION 3 − HEADGEAR COOLING SYSTEM
Read and follow these instructions and the safety labels carefully. This product is intended for use as a cooling device only. It is not a respiratory protective device and does
not protect the user from airborne contaminants. Have an industrial hygienist test the air
in your facility to determine if respiratory protection is required to provide adequate
protection from contaminants in your environment. With cooling system-equipped helmet on your head and cooling system operating, also test the air inside the helmet to
determine if respiratory protection is required. If you have questions about the type of respiratory protection equipment required, consult your safety director and an Industrial
Hygienist.
. Use the cooling system only with compatible Miller welding helmets (MP-10, Pro-Hobby,
Performance, Elite, Titanium series helmets). See the welding helmet Owner’s Manual for
information on helmet operation.
The CoolBandt headgear cooling system draws in air and blows it to the front of the welding helmet
through a flexible tube. The system also generates a positive air pressure to help prevent contaminants from entering the helmet. The system must include and/or be used with the equipment listed
below:
D Helmet and head shroud
D Blower assembly with properly-installed filter
D Battery charger with AC power adapter
The helmet cooling system operates at temperatures from 14° to 131° F (−10° to 55° C) The Battery
Level red light flashes and blower assembly pulses on and off when battery power is low.
. To
better show components
and features, the helmet cooling system is shown without
welding helmet.
OM-235 369 Page 5
3-1. Helmet Cooling System Specifications
Application
Fits Most Miller Welding Helmets
Weight
Total Weight With Battery: 17.6 oz. (500 g)
Added Weight To Helmet If Using Battery Power:
13.1 oz. (371 g)
Added Weight To Helmet If Using AC Power:
10.2 oz. (289 g)
Air Filter
. Filter is required for proper op-
Use Miller Filter Only
(Miller Part No. 243 932)
eration of equipment, but does
not provide respiratory protection.
Operating Temperature
14° to 131° F (−10° to 55° C)
Storage Temperature
(For Up To Six Months Storage
With Battery 50% Charged)
Acceptable: 23° to 95° F (−5° to 35° C)
Preferred: 68° to 86° F (20° to 30° C)
Battery Type
Rechargeable Lithium, 1600 mAh, 7.4 V (Rated) 8.4 V (Fully
Charged)
Battery Charging Time
About 3.5 hours (Typical); 4.5 hours (max.)
Battery Charging Temperature
32° to 104° F (0° to 40° C)
Battery Life
New Battery: 6 Hours Run Time (Typical); 5.3 hours (Min.)
. Battery retains about 80% of original battery life after 300
charges. Battery may be recharged about 500 times.
AC Adapter
Output: 12 V, 500 mA
Cord Length: 9.8 ft (3 m)
Shroud Service Life
Replace After 50 Washings
OM-235 369 Page 6
3-2. Installing Headgear
1
2
3
Distance Adjustment Knob
O−Ring
Washer
Remove knobs, o−rings, and washers from helmet headgear. Remove
headgear. Install helmet cooling
system headgear and secure with
knobs, o−rings, and washers.
Retain old headgear for future use.
. See Section 4
for helmet adjustment information.
3
2
1
OM-235 369 Page 7
3-3. Installing Head Shroud
.
1
2
3
1
2
3
After installing shroud,
make sure there are no
gaps between shroud and
helmet edge.
Head Shroud
Magnetic Fastener
Elastic Loops
Position head shroud magnetic
fasteners on inside and outside
of helmet edge.
Stretch head shroud elastic
loops over helmet distance adjustment knobs.
. Remove
shroud from helmet when using helmet with
the cooling system turned
off.
Notes
Work like a Pro!
Pros weld and cut
safely. Read the
safety rules at
the beginning
of this manual.
OM-235 369 Page 8
3-4. Charging The Battery
4
3
1
2
161-003
.
.
.
Charge battery only
with supplied charger
in an open, well−ventilated location.
. Dispose of battery at a
Do not allow battery
to get wet. Do not attempt to open the battery case.
matically stops when
battery is fully charged.
Battery
Battery Charger
12 Volt AC Power
Adapter
120 Volt 15 A AC
Receptacle
Keep battery away
from fire or heat.
. Remove tape from battery terminals before
using battery.
. Charge battery before
first use or if battery has
not been used for five
days.
designated collection
facility.
. Battery charging auto1
2
3
4
. Place
battery charger
on flat, level surface or
use supplied screw to
mount charger on wall.
Remove battery from blower assembly (see Section
3-5).
Place battery in charger
base. Connect AC power
adapter cord to charger
base. Connect AC power
adapter to 120 volt AC receptacle.
The charger red light goes
on when battery is being
charged.
When
fully
charged, the charger green
light goes on. Charging normally takes between 3.5
hours (typical) and 4.5
hours (max.)
. See Section 3-10 to operate helmet cooling
system on AC (utility)
power.
OM-235 369 Page 9
3-5. Installing The Battery
.
Do not allow battery to get
wet. Do not attempt to open
the battery case.
.
Keep battery away from
fire or heat.
. To better show components
1
2
and features, the helmet
cooling system is shown
without welding helmet.
Access Door
Battery
Open battery access door. Slide
battery into blower assembly until
terminals touch back of battery
compartment.
. Remove
tape from battery
terminals. Install battery with
terminals facing helmet cooling system as shown.
2
1
Close door.
. See Section 3-10 to operate
helmet cooling system on AC
power.
3-6. Installing The Filter
1
2
3
.
Do not use the helmet cooling
system without the filter installed.
.
Replace damaged or dirty filter. Do not wash filter, clean
with compressed air, or reuse
dirty filter.
. Filter is required for proper oper1
2
3
ation of equipment, but does not
provide respiratory protection.
Filter Cover
Filter
Finger Tab
Grip finger tab to pull cover away
from blower assembly. Install filter.
Reinstall cover so it fits tightly around
filter area.
. Filter is shaped to fit only one
way in blower assembly. Be sure
filter is installed correctly.
OM-235 369 Page 10
3-7. Removing Air Deflector To Adjust Air Flow
1
2
Air Deflector
Manifold
To adjust air flow in helmet, remove air deflector from manifold.
Save air deflector for later use.
2
1
Notes
Work like a Pro!
Pros weld and cut
safely. Read the
safety rules at
the beginning
of this manual.
OM-235 369 Page 11
3-8. Operating The Controls
1
2
.
3
Read and follow these
instructions and the
safety labels carefully.
This product is intended for use as a
cooling device only. It
is not a respiratory protective device and does
not protect the user
from airborne contaminants. Have an industrial hygienist test the
air in your facility to determine if respiratory
protection is required
to provide adequate
protection from contaminants in your environment. With cooling
system-equipped helmet on your head and
cooling system operating, also test the air inside the helmet to determine if respiratory
protection is required.
If you have questions
OM-235 369 Page 12
.
1
about the type of respiratory
protection
equipment required,
consult your safety director and an Industrial
Hygienist.
2
Do not restrict or alter
helmet cooling system
air flow. Do not block
air holes (including upper and lower holes).
Be sure safety glasses,
hair, weld cap, and other objects do not block
air flow.
The Battery Level red light
flashes and blower assembly
pulses on and off when battery power is low.
Power Button
To Start: Press Power button. Blower assembly starts
when button is released.
To Stop: Press Power button
again.
. Light pressure on Power
button turns unit off.
Battery Level Light
The Battery Level green light
goes on when blower assembly is running and battery
is charged.
The blower assembly stops
and Battery Level red light
stays on when battery is fully
discharged. See Section 3-4
for battery charging information.
3
Aux Power Jack
Connect AC power adapter
cord to Aux Power jack to operate helmet cooling system
on 120 volt AC power (see
Section 3-10). Reinstall cover
when not using Aux Power
jack.
3-9. Checking The Helmet Cooling System Before Use
2
1
3
5
.
Read and follow these instructions and the safety
labels carefully. This
product is intended for
use as a cooling device
only. It is not a respiratory protective device and
does not protect the user
from airborne contaminants. Have an industrial
hygienist test the air in
your facility to determine
if respiratory protection
is required to provide adequate protection from
contaminants in your environment. With cooling
system-equipped helmet
on your head and cooling
system operating, also
test the air inside the helmet to determine if respiratory protection is required. If you have questions about the type of
respiratory protection
equipment
required,
consult your safety director and an Industrial
Hygienist.
.
Do not restrict or alter
helmet cooling system
air flow. Do not block air
holes (including upper
and lower holes). Be sure
safety glasses, hair, weld
cap, and other objects do
not block air flow.
3
Battery
Verify the battery is fully
charged and secured in the battery compartment.
4 Air Flow
Turn on blower assembly and
test air flow.
5 Air Deflector
Before using the helmet cooling
system, check the following To adjust direction of air flow,
remove air deflector (see Secitems:
tion 3-7).
1 Filter
6 Shroud (Not Shown)
. Filter is required for proper
Inspect the shroud and replace
operation of equipment, if damaged. See Troubleshootbut does not provide respir- ing (Section 4-4) if air is not being supplied to front of helmet.
atory protection.
Put on helmet and adjust helVerify the filter is undamaged, met so helmet fits snugly on
properly assembled, and se- head. Verify shroud is properly
curely connected to the blower installed on helmet.
assembly.
. See Section 4 (Miller hel2 Flexible Tube
met) or the welding helmet
Owner’s Manual for helmet
Be sure the tube is undamaged
adjustment information.
and properly connected to the
manifold and blower assembly.
OM-235 369 Page 13
3-10. Operating Helmet Cooling System On 120 Volt AC Power
1
1
Auxiliary Power Jack
To operate helmet cooling
system on AC (utility)
power, remove cord from
charger base and connect
to Aux Power jack on
blower assembly. Connect
other end of cord to 120 volt
15 A AC receptacle.
. The battery is not be-
ing charged when the
helmet cooling system
is connected to an AC
power supply.
. Battery
can be removed from helmet
cooling system when
using AC power.
. Obtain
an additional
AC Power Adapter to
charge the battery
when the helmet cooling system is operating
on AC power (see Section 5 − Parts List).
Notes
Work like a Pro!
Pros weld and cut
safely. Read the
safety rules at
the beginning
of this manual.
OM-235 369 Page 14
SECTION 4 − MAINTENANCE
4-1. Adjusting Headgear
. There are four headgear adjust1
1
3
ments: headgear top, tightness,
angle adjustment, and distance
adjustment.
Headgear Top
Adjusts headgear for proper depth
on the head to ensure correct balance and stability.
2 Headgear Tightness
To adjust, push in the adjusting knob
located on the back of the headgear
and turn left or right to desired tightness.
. If adjustment is limited, it may be
3
necessary to remove the comfort cushion.
Distance Adjustment
Adjusts the distance between the
face and the lens. To adjust, loosen
both outside tension knobs and
press inward to free from adjustment
slots. Move forward or back to desired position and retighten. (Both
sides must be equally positioned for
proper vision.)
4 Angle Adjustment
2
4
Four pins on the right side of the
headband top provide adjustment
for the forward tilt of the helmet. To
adjust, loosen the right outside tension adjustment knob then lift on the
control arm tab and move it to the desired position. Retighten tension adjustment knob.
. When using the back distance
adjustment positions, only the
back three angle adjustment
pins can be used.
804 118
OM-235 369 Page 15
4-2. Replacing Fabric Headband
1
2
3
1
Slide manifold up and away from
manifold bracket. Push bracket toward fabric headband and slide
bracket sideways to align slot with
tab on headgear. Remove bracket.
2
3
2
3
Slide Bracket
OM-235 369 Page 16
Manifold
Manifold Bracket
Fabric Headband
Remove fabric headband and clean
or replace. Reinstall fabric headband, manifold bracket, and manifold in reverse order of disassembly.
4-3. Maintenance And Storage
Replace damaged or dirty filter. Do not wash filter, clean with compressed air, or reuse
dirty filter.
Never use solvents or abrasive cleaning solutions to clean the helmet cooling system.
Keep water and other fluids out of blower assembly.
Replace shroud after 50 washings. Shroud loses its fire retardant properties with repeated washing.
For best performance clean the equipment after each use. Use a soft cloth dampened with a mild soap
and water solution to wipe all external surfaces clean. Allow to air dry.
Product usage, workplace contamination levels, and other factors affect the life of the filter. Replace
filter if air flow is reduced due to a dirty filter (see Section 3-6).
Inspect flexible tube and replace if damaged or if inside of tube is extremely dirty.
If the helmet cooling system will not be used for an extended period, remove the filter and battery and
store in a clean, dry place free of solvent-based vapors them and at a temperature of −4° to 86° F (−20°
to 30° C). Charge battery to 50 percent capacity before storage.
4-4. Helmet Cooling System Troubleshooting
Trouble
Blower assembly does not
supply air to helmet.
Remedy
Press Power button.
Dead battery; recharge battery (see Section 3-5).
Remove tape from battery terminals (new battery only).
Verify battery contacts are clean and free of obstructions.
Remove blockage from blower assembly outlet and tube.
Blower assembly runs for
short time even though
battery is fully charged.
Be sure battery is properly connected to battery charger.
Replace battery.
Replace charger.
Battery Level red light is
on or flashing.
Charge or replace the battery. The blower assembly will operate
for about 15 minutes after the light starts flashing.
Blower assembly is
pulsing on and off.
Charge or replace the battery. The blower assembly will operate
for about 15 minutes after the light starts flashing.
OM-235 369 Page 17
Battery run time is too
short.
Replace battery.
Check filter and replace if necessary (see Section 3-6). A clogged
filter element reduces battery life.
Air supplied to helmet
smells and tastes unusual;
eyes and throat irritation.
Continue wearing the helmet cooling system and leave the area
immediately. Check contamination level of filter, and replace filter
if necessary.
Check flexible tube connection to blower assembly and manifold.
Have Safety Director and an Industrial Hygienist determine if you
are using the proper equipment for the work environment.
Blower assembly supplies
insufficient air to helmet.
Check filter and replace if necessary (see Section 3-6).
Check flexible tube connection to blower assembly and manifold.
Remove blockage from blower assembly outlet and/or tube.
OM-235 369 Page 18
SECTION 5 − PARTS LIST
7
1
8
11
4
2
5
6
3
9
10
Figure 5-1. CoolBand Helmet Cooling System
Item
No.
Part
No.
Description
Quantity
Figure 5-1. CoolBand Helmet Cooling System
1 . . . . . . . . 244094 . . . . CoolBand Unit (Entire System − Helmet Not Included) . . . . . . . . 1
2 . . . . . . . . 243931 . . . . Shroud, Head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
3 . . . . . . . . 243930 . . . . Deflector, Air . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
4 . . . . . . . . 243923 . . . . Manifold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
5 . . . . . . . . 243924 . . . . Bracket, Manifold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
6 . . . . . . . . 770249 . . . . Headband, Fabric . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
7 . . . . . . . . 243926 . . . . Headgear Set (Includes Knobs, Springs, Headbands, Mounting
Gears, Screws) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
8 . . . . . . . . 243927 . . . . Battery, Rechargeable Lithium Polymer . . . . . . . . . . . . . . . . . . . . . 1
9 . . . . . . . . 243932 . . . . Filter (Pack of 10) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
10 . . . . . . . 243925 . . . . Tubing, Stretch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
11 . . . . . . . 216336 . . . . Cushion, Comfort . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . . . . . . . 243928 . . . . Charger, Battery (Not Shown) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . . . . . . . 243929 . . . . Adapter, AC Power (Not Shown) . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
OM-235 369 Page 19
SECTION 6 − LIMITED WARRANTY
LIMITED WARRANTY – Subject to the terms and conditions below. Miller
Electric Mfg. Co., Appleton, Wisconsin, warrants to its original retail purchaser that the new Miller equipment sold after the effective date of this
limited warranty is free of defects in material and workmanship at the time
it is shipped by Miller. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL
OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE
WARRANTIES OR MERCHANTABILITY AND FITNESS.
The headgear cooling system is warranted for one year from the date of
purchase. Proof of purchase is required for warranty transactions so it is
imperative that a copy of the original invoice or sales receipt be retained.
For warranty transactions, contact your Miller Distributor.
Effective January 1, 2009
OM-235 369 Page 20
Visit our website at
www.MillerWelds.com
®
Miller Electric Mfg. Co.
An Illinois Tool Works Company
1635 West Spencer Street
Appleton, WI 54914 USA
ORIGINAL INSTRUCTIONS
© 2009 Miller Electric Mfg. Co.