Martin MAC 101 Series User manual

MAC 250 Krypton
user manual
All measurements are expressed in millimeters
538
469
364
119
375
315
393
270°
270°
128.5°
128.5°
560
© 2001-2002 Martin Professional A/S, Denmark. All rights reserved. No part of this manual may be reproduced, in any form or by any
means, without permission in writing from Martin Professional A/S, Denmark. Printed in Denmark.
P/N 35000126 Rev. A
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
About this manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
MAC 250 Krypton safety information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Unpacking. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Lamp installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AC power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting the serial data link . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6
6
7
8
9
CONTROL PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Menu navigation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DMX Mode selection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DMX Address selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tailoring performance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Information readouts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Test and service utilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11
11
11
11
12
13
DMX-512 CONTROL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Lamp power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Effect position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Speed control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
OPTICAL CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Gobos . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Color filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Prism. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Lamp replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Replacing fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Updating software. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
24
24
25
25
26
DMX PROTOCOL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
CONTROL MENU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
ERROR MESSAGES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
CIRCUIT BOARD CONNECTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
SPECIFICATIONS - MAC 250 KRYPTON . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
INTRODUCTION
Thank you for selecting the Martin MAC 250 Krypton.
Features
Some of the many features include:
•
•
•
•
•
•
•
•
•
•
efficient, 2000 hour, 250 watt discharge lamp
12 interchangeable dichroic colors
7 interchangeable indexed-rotation gobos
interchangeable 3-facet rotating prism
motorized focus
full-range dimming
fast blackout and strobe effects
coated optics
user-installable firmware
switch-selectable power supply settings
For the latest firmware updates, documentation, and other information about this and all Martin Professional
products, please visit the Martin web site at http://www.martin.dk.
About this manual
This manual is preliminary and describes the specified functionality. Some of the described features are not
present in the initial release of the MAC 250 Krypton software. Please check the Martin web site at
http://www.martin.dk for the latest product software and documentation.
Comments or suggestions regarding this document may be e-mailed to service@martin.dk or posted to
Martin Professional A/S
Olof Palmes Allé 18
DK-8200 Aarhus N, Denmark
Attn: Service Department
Please review the important safety precautions in this manual before installing and operating the fixture.
MAC 250 Krypton safety information
Warning!
This product is for professional use only. It is not for household or residential use.
This product presents risks of lethal or severe injury due to fire and heat, electric shock, ultraviolet radiation,
lamp explosion, and falls. Read this manual before powering or installing the fixture, follow the safety
precautions listed below and observe all warnings in this manual and printed on the fixture. If you have
questions about how to operate the fixture safely, please contact your Martin dealer or call the Martin
24-hour service hot line at +45 70 200 201.
PROTECTION FROM ELECTRIC SHOCK
Warning!
Always disconnect from mains supply before replacing the lamp.
• Disconnect the fixture from AC power before removing or installing the lamp, fuses, or any part, and when
not in use.
• Always ground (earth) the fixture electrically.
4
MAC 250 Krypton
• Use only a source of AC power that complies with local building and electrical codes and has both overload
and ground-fault protection.
• Do not expose the fixture to rain or moisture.
• Refer any service operation not described in this manual to a qualified technician.
PROTECTION FROM UV RADIATION AND LAMP EXPLOSION
• Never operate the fixture with missing or damaged lenses and/or covers.
• When replacing the lamp, allow the fixture to cool for at least 15 minutes before opening the fixture or
removing the lamp. Protect your hands and eyes with gloves and safety glasses.
• Do not stare directly into the light. Never look at an exposed lamp while it is lit.
• Replace the lamp if it becomes defective or worn out, or before usage exceeds the maximum service life.
PROTECTION FROM BURNS AND FIRE
Danger!
Intense heat. Avoid contact by persons and materials.
The exterior of the fixture can get very hot - up to 120° C (248° F). Allow the fixture to cool
for at least 45 minutes before handling.
Prolonged exposure to unshielded lamp can cause eye and skin burns.
• Never attempt to bypass the thermostatic switch or fuses. Always replace defective fuses with ones of the
specified type and rating.
• Keep all combustible materials (for example fabric, wood, paper) at least 1 meter (39 inches) away from the
fixture. Keep flammable materials well away from the fixture.
• Do not illuminate surfaces within 3 meters (10 feet) of the fixture.
• Provide a minimum clearance of 0.1 meters (4 inches) around fans and air vents.
• Never place filters or other materials over the lens.
• Do not modify the fixture or install other than genuine Martin parts.
• Do not operate the fixture if the ambient temperature (Ta) exceeds 40° C (104° F). Protection from injury
due to falls
• Do not lift or carry the fixture alone.
• When suspending the fixture, verify that the structure can hold at least 10 times the weight of all installed
devices.
• Verify that all external covers and rigging hardware are securely fastened and use an approved means of
secondary attachment such as a safety cable.
• Block access below the work area whenever installing or removing the fixture.
Introduction
5
SETUP
Unpacking
The MAC 250 Krypton comes with:
•
•
•
•
•
MSD 250/2 lamp (not installed)
3-meter, 3-wire IEC power cable
user manual
1/4-turn clamp mounting bracket
5-meter, 3-pin shielded XLR control cable
The packing material is carefully designed to protect the fixture during shipment - always use it or a custom
flight case to transport the fixture.
Lamp installation
A lamp must be installed prior to initial operation.
COMPATIBLE LAMPS
A Philips MSD 250/2 lamp is included. The MAC 250 Krypton lamp options are shown in the table below.
Installing any other lamp may damage the fixture.
Lamp
Average life
Color Temp.
Osram HSD 250/78
3000 hr
7800K
Philips MSD 250/2
2000 hr
9000K
GE CSD 250/2
2000 hr
9000K
Table 1: Lamp comparison
INSTALLING A LAMP
Danger!
Intense heat. Avoid contact by persons and materials. The exterior of the fixture can get
very hot - up to 120° C (248° F). When replacing the lamp, disconnect the fixture from AC
power and allow it to cool for at least 45 minutes before proceeding. Wear safety goggles
to protect your eyes.
3
mm
#2
Figure 1: Lamp installation
1
6
Locate the lamp access cover at the back of the fixture head and remove the Phillips screws.
MAC 250 Krypton
2
Pull out the lamp socket.
3
If changing the lamp, remove the old lamp from the socket.
4
Holding the new lamp by its ceramic base (do not touch the glass), align the small pin on the lamp with the
small hole in the socket and insert the lamp squarely. Make sure that the 4 small projections on the base
contact the face of the socket.
5
Clean the glass bulb with the cloth supplied with the lamp, particularly if your fingers touched the glass. A
clean, lint-free cloth wetted with alcohol may also be used.
6
Insert the lamp into the fixture with as little twist in the lamp wires as possible.
7
Align the screw holes and fasten the lamp access plate with 2 screws.
8
If replacing the lamp, reset the lamp hour and lamp strike counters as described on page 12.
9
Strike the lamp (after setup is complete) and adjust it for optimum performance by turning the 3 adjustment
screws one at a time until the brightest part of the beam is centered.
10 Adjust the lamp position if necessary by turning the 3 lamp adjustment screws to the middle of their range
using a 3 mm Allen wrench.
AC power
Warning!
For protection from electric shock, the fixture must be grounded (earthed). The power
supply shall have overload and ground-fault protection.
Important! Verify that power supply settings match the local AC supply before use.
The MAC 250 Krypton is factory configured for 230 V / 50 Hz operation. If your AC power supply is different,
the fixture must be configured for the local voltage and frequency. Always use the settings that are closest
to your AC supply.
CONFIGURING FOR LOCAL AC POWER
Frequency
50
60
Voltage
250
230
210
100
120
Figure 2: Power supply settings
1
Disconnect the fixture from power.
2
Remove the 2 Phillips screws in the access cover directly behind the power and data connectors. Lift off the
cover.
3
Locate the selection switches.
Setup
7
4
Move the voltage switch to the setting that most closely matches the local AC voltage. If your voltage falls
halfway between 2 settings, select the higher voltage. For example, if the AC voltage is 220 V, use the 230
V setting instead of 210 V.
5
Move the frequency switch to the setting that matches the local AC frequency: 50 or 60 Hz.
6
Replace the cover.
INSTALLING A PLUG ON THE POWER CABLE
The power cable must be fitted with a grounding-type cord cap that fits your power distribution system.
Consult an electrician if you have any doubts about proper installation.
• Following the cord cap manufacturer’s instructions, connect the yellow and green wire to ground (earth), the
brown wire to live, and the blue wire to neutral. The table below shows some pin identification schemes.
Wire
Pin
brown
Marking
live
“L”
blue
neutral
“N”
yellow/green
ground
Screw color
yellow or brass
silver
green
Table 2: Plug wiring
APPLYING POWER
Warning!
The power cables must be undamaged and rated for the electrical requirements of all
connected devices.
Important! Powering through a dimmer system can damage the fixture.
1
Verify that the supply cable is undamaged and rated for the current requirements of all connected devices.
2
Plug the prepared power cable into the AC socket and a grounded AC power supply.
Installation
LOCATION AND ORIENTATION
The MAC 250 Krypton may be installed in any orientation. It can be fastened directly to a suitable surface,
hung with a rigging clamp, or placed directly on a level surface.
For safe operation, install the MAC 250 Krypton in a location where:
•
•
•
•
the fixture is at least 1 meters (39 inches) away from combustible materials
the fixture is protected from rain and moisture
there is at least 0.1 meters (4 inches) clearance around the fan and control panel
there are no flammable materials nearby
RIGGING OR MOUNTING THE MAC 250 KRYPTON
Warning!
Block access below the work area before proceeding.
The MAC 250 Krypton can be placed on stage or clamped to a truss in any orientation. The Fast-Lock
system enables quick and easy fastening of the clamp brackets in 4 positions.
8
MAC 250 Krypton
The MAC 250 Krypton includes an omega clamp mounting bracket to which 1 or 2 rigging clamps (not
included) can be bolted. The clamp mounting bracket fastens to the base as shown with 1/4-turn fasteners.
Figure 3: Clamp mounting bracket
Warning!
Attach an approved safety cable to the attachment point provided in the base. Never use
the carrying handles for secondary attachment. Always use an approved safety cable.
The 1/4-turn fasteners are locked only when turned fully clockwise.
1
Verify that the clamps are in good condition and can bear at least 10 times the weight of the fixture. Bolt
clamps to the bracket with a grade 8.8 (minimum) M12 bolt and lock nut, or as recommended by the clamp
manufacturer, through the 13 mm holes in the clamp mounting bracket.
2
Align the clamp mounting bracket with any 2 key slots on the base. Insert both locking pins into the slots and
turn both levers a full 1/4 turn clockwise to lock.
3
Verify that the structure can bear at least 10 times the weight of all installed fixtures, clamps, cables,
auxiliary equipment, etc.
4
Working from a stable platform, clamp the fixture to the structure.
5
Install a safety cable that can bear at least 10 times the weight of the fixture securely to the structure and
anchor the cable to the dedicated attachment point on the base. The attachment point is designed to fit a
carabiner clamp.
6
Verify that there are no combustible materials or surfaces to be illuminated within 1 meter (39 inches) of the
fixture, and that there are no flammable materials nearby.
Connecting the serial data link
The MAC 250 Krypton has locking 3-pin and 5-pin data input and output sockets that are wired for
use with DMX devices with pin 1 to shield, pin 2 to cold (-) and pin 3 to hot (+).
Important! Never connect more than 1 data input and 1 data output.
1
Connect the controller’s output to the fixture’s data input.
2
Connect the output of the fixture closest to the controller to the input of the next fixture. If connecting a
fixture with pin 3 hot to a fixture with pin 3 cold, use a phase-reversing adaptor.
Setup
9
3
To terminate the link, insert a male 120 Ω XLR termination plug in the output of the last fixture.
TIPS FOR BUILDING A SERIAL LINK
• Use shielded twisted-pair cable designed for RS-485 devices: standard microphone cable cannot transmit
DMX data reliably over long runs. For links up to 300 meters (1000 ft.) long, you can use 24 AWG, low
capacitance, 85-150 ohm characteristic impedance, shielded cable with 1 or more twisted pairs. For runs up
to 500 meters (1640 ft.) use 22 AWG cable. Use an amplifier if the serial link exceeds 500 meters.
• Never use a “Y” connector to split the link. To split the serial link into branches use a splitter such as the
Martin 4-Channel Opto-Isolated RS-485 Splitter/Amplifier.
• Do not overload the link. Up to 32 devices may be connected on a serial link.
• Terminate the link by installing a termination plug in the output socket of the last fixture on the link. The
termination plug, which is simply a male XLR connector with a 120 ohm, 0.25 watt resistor soldered
between pins 2 and 3, “soaks up” the control signal so it does not reflect back down the link and cause
interference. If a splitter is used, terminate each branch of the link.
10
MAC 250 Krypton
CONTROL PANEL
You set the address and personalities, read out data, and execute service utilities from the control panel.
Settings can also be changed remotely via the serial link with the Martin MP-2 uploader.
See also the control menu table starting on page 30.
Menu navigation
The DMX address and any error messages are displayed after the fixture resets. To enter the menu, press
[menu]. Use the [up] and [down] keys to move within the menu. To select a function or submenu, press
[enter]. To escape a function or menu, press [menu].
DMX Mode selection
The fixture has two DMX operating modes, 16-bit and 16-bit Extended. 16-bit Extended mode uses 17 DMX
channels, three more than the 14 DMX channels than standard 16-bit mode requires. 16-bit Extended mode
provides more precise control of the dimmer color, and focus settings. The DMX mode is selected using the
PSET option in the fixture control menu (see “Control menu” on page 30).
SETTING THE DMX MODE
1
Apply power to the MAC 250 Krypton. Press [menu] to enter the main menu.
2
Select PSET using the [up] and [down] keys. Press [enter].
3
Select 16BT for standard 16-bit mode, or 16EX for 16-bit extended mode.Press [enter].
4
Press [menu] to return to the main menu.
DMX Address selection
For independent control, each fixture must be assigned its own address and non-overlapping control
channels. Two MAC 250 Kryptons can share the same address if they are to respond identically: they will
receive the same instructions and individual control will not be possible.
SETTING THE DMX ADDRESS
1
Apply power to the MAC 250 Krypton. Press [menu] to enter the main menu.
2
Select AddR using the [up] and [down] keys. Press [enter].
3
Select an address (start channel) from 1 to 500 using the [up] and [down] keys. Press [enter]. Press [menu]
to return to the main menu.
Tailoring performance
MOVEMENT
The MAC 250 Krypton provides the three menus with options for optimizing movement to suit different
applications.
• PA TI , the pan and tilt invert menu, allows you to swap the pan and tilt channels (S W AP >O N ), invert pan
movement (P IN V >O N ), and invert tilt movement (TI N V> ON ). These options can be useful in situations
Control Panel
11
where you want some fixtures to mirror the performance of others with the same DMX address, or when
fixtures are not oriented as programmed.
• PT SP, the pan/tilt speed menu, provides 3 settings: F A ST , N OR M a nd SL O W . N OR M is best for
most applications. F AS T provides better performance in applications where speed is most important.
• SC UT, the shortcuts setting which can be found under the PERS (personality) menu, determines whether
the color and gobo wheels scroll past open when changing positions. When set to O N , the wheels can “take
a shortcut” and scroll through open when this is the shortest path to the next position. The wheels do not
scroll past open when SC U T is set to OFF.
DISPLAY
The display menu (P E R S > d I S P ) determines whether the display remains lit or not. Select O N to have
the display remain lit, or OFF to extinguish the display two minutes after the last key press.
To flip the display for easier reading, press [up] and [down] simultaneously.
The display intensity setting ( P E R S > d I N T ) controls display brightness. You can select A U T O for
automatic dimming of the display using the built-in light sensor, or manually select an intensity level from 10
to 100.
LAMP POWER
There are two settings that modify lamp control: Automatic Lamp On (P ER S> A LO N ) and DMX Lamp-Off
(P E RS > DL oF ).
There are three options for automatic lamp control: O N , O F F, and D M X . When A L O N is O F F, the lamp
remains off until a lamp-on command is received from the controller. When A LO N is O N , the lamp strikes
automatically after the fixture is powered on. When A L O N is set to D M X , the lamp strikes automatically
when the fixture receives DMX data, and it extinguishes automatically 15 minutes after DMX data is lost.
When ALON is either ON or DMX, lamp strike timing is determined by the fixture address to prevent all
lamps from striking at once.
The DMX Lamp-Off setting effects how the lamp can be turned off. When d L OF is O N , lamp power can be
switched off by sending a DMX value from 248 to 255 on channel 1 for five seconds. When d L OF is OF F,
the lamp-off command will not work unless special conditions are met. Refer to the DMX protocol.
RESET
The fixture can be reset from the controller if DMX reset (P E RS >d R ES ) is set to 5 S EC . If DMX reset is
OF F, this command will not work unless special conditions are met. Refer to the DMX protocol.
DEFAULT SETTINGS
The fixture can be reset to its factory default settings by selecting dF S E> FA C T> LO A d.
Information readouts
POWER-ON HOURS
Read the total number of hours the fixture has been on since fabrication (I NF O> T IM E> H RS >T O TL ),
and the number of hours on since the counter was last reset (I NF O >T IM E >H R S> RS E T ). This can be
used to track maintenance intervals. Press [up] for 5 seconds while displayed to reset.
LAMP HOURS
Read the total number of lamp hours since fabrication (I NF O >T IM E >L HR > TO T L ), and the number
of lamp hours since the counter was last reset (I N FO >T I ME > L H R> R SE T ). Reset this counter after
installing a new lamp. Press [up] for 5 seconds while displayed to reset.
12
MAC 250 Krypton
LAMP STRIKES
Read the total number of lamp strikes (IN F O> TI M E> L S T >T OT L ), and the number of lamps strikes
since the counter was last reset (I N F O > T I M E > L S T > R S E T ). Reset this counter when installing a
new lamp. Press [up] for 5 seconds while displayed to reset.
FIRMWARE VERSION
I N F O > V E R displays the firmware version number. The firmware version is also displayed briefly at
startup.
Test and service utilities
DMX READOUT
The DMX log (d MX L ) menu provides useful information for troubleshooting control problems.
R A T E displays the DMX refresh rate in packets per second. Values lower than 10 or higher than 44 may
result in erratic performance, especially when using tracking control.
q U A L displays the quality of the received DMX data as a percentage of packets received. Values much
below 100 indicate interference, poor connections, or other problems with the serial data link that are the
most common cause of control problems.
S T C O displays the DMX start code. Packets with a start code other than 0 may cause irregular
performance.
The remaining options under d M X L display the DMX values received on each of the 13 channels, from
SH UT (shutter, channel 1) to E FS P (effect speed, channel 13). If the fixture does not behave as expected,
reading the DMX values can help you troubleshoot the problem.
MANUAL CONTROL
The manual control menu (M A N ) provides commands for turning the lamp on (L O N ), turning the lamp off
(L o FF ), and resetting the fixture (R ST ). It also permits you to position and move individual effects.
EFFECTS TEST
The test sequence (T S EQ >R U N ) runs through all effects to provide a quick check of fixture performance.
Note: the test sequence does not automatically strike the lamp. Use M A N > L O N and M A N > L o F F to
control lamp power. Press [menu] to stop the test.
FEEDBACK TOGGLE
Magnetic sensors monitor the positions of the color wheel, gobo wheel, and rotating gobos. If they detect an
error, the shutter closes while the effect resets. This feature can be disabled by turning effects feedback off
(U T IL > EF Fb >O F F ).
ADJUSTMENT POSITIONS
The adjustment menu ( U T I L > A d J ) provides commands for positioning effects during mechanical
adjustment.
EFFECT CALIBRATION
With the calibration menu (U TI L >C A L ), effect positions can be fine-tuned with a software-defined offset
value to compensate for small misalignments or differences between fixtures.
The default offset command (U TI L >d FO F ) erases any offsets stored in memory.
CIRCUIT BOARD TEST
UT IL > PC B T executes a routine designed for testing the main circuit board. For service use only.
Control Panel
13
UPLOAD MODE
The upload mode command (U TI L >U P Ld ) prepares the fixture for a software update. This command is
not necessary, however, as upload mode is engaged automatically by the uploader.
14
MAC 250 Krypton
DMX-512
CONTROL
The MAC 250 Krypton is compatible with USITT DMX512 controllers. The full protocol is available in “DMX
protocol” on page 27.
The fixture has two DMX operating modes, 16-bit and 16-bit Extended. 16-bit Extended mode uses 17 DMX
channels, three more than the 14 DMX channels than standard 16-bit mode requires. 16-bit Extended mode
provides more precise control of the dimmer color, and focus settings. All other functions are identical. See
“DMX protocol” on page 25.This section briefly describes the DMX-controllable effects. The DMX mode is
selected using the PSET option in the fixture control menu (see “Control menu” on page 30).
Lamp power
LAMP-ON
Unless automatic lamp strike is enabled, lamp power remains off until a lamp-on command is sent from the
controller.
Note: A peak of electric current that can be many times the operating current is drawn for an instant when
striking a discharge lamp. Striking many lamps at once may cause a voltage drop large enough to prevent
lamps from striking or draw enough current to trip circuit breakers. If sending lamp-on commands to multiple
fixtures, program a sequence that strikes lamps one at a time at 5 second intervals.
LAMP-OFF
The lamp can be turned off from the controller by sending the lamp-off command on channel 1 for 5
seconds. The lamp cannot be restruck for 8 minutes after being turned off. Note that the
lamp-off command may be disabled by the DMX Lamp-Off personality setting (PERS/dLOF).
Effect position
RESET
If an effect loses its indexing and fails to move to programmed positions, the fixture can be reset from the
controller by sending the “Reset” command on channel 1 for 5 seconds. Note that the DMX reset feature
may be disabled by the DMX Reset personality setting (PERS/dRES).
DIMMER / SHUTTER
The mechanical dimmer/shutter system provides full, high-resolution dimming, “instant” open and blackout,
random and variable strobe effects, and random and variable pulses in which the dimmer snaps open and
slowly dims or snaps closed and slowly opens. Shutter, strobe, and pulse effects are selected on channel 1.
The intensity level is selected on channel 2. 16-bit Extended mode provides fine tuning of the intensity level
on channel 3.
COLOR
The color wheel can be scrolled continuously - allowing for split color effects - or in steps, and rotated
randomly or continuously in both directions at different speeds. 16-bit Extended mode provides finer tuning
on channel 5 of the color setting selected on channel 4.
GOBO ROTATION AND SELECTION
The MAC 250 Krypton has 7 indexed-rotation gobo positions plus an open position. Gobos can be indexed
(positioned at a defined angle), rotated continuously, or rotated and shaken (bounced). The gobo and the
type of movement are selected on channel 4 (channel 6 in 16-bit Extended mode) and the index angle or
DMX-512 control
15
rotation speed are selected on channel 5 (channel 7 in 16-bit Extended mode). Fine tuning of this index
position or rotation is available on channel 6 (channel 8 in 16-bit Extended mode).
The gobo wheel can also rotate continuously in both directions at variable speed.
FOCUS
The beam may be focused from approximately 2 meters (6.5 feet) to infinity using channel 7. 16-bit
Extended mode provides finer tuning on channel 5 of the color setting selected on channel 4.
ROTATING PRISM
The prism is controlled using channel 8 (channel 10 in 16-bit Extended mode). It may be inserted and
removed from the light path. It rotates in both directions at varying speeds.
PAN AND TILT
Head pan and tilt are controlled on channels 9 to 12 (channel 12 to 15 in 16-bit Extended mode). The
course control channel sets first 8 bits (the most significant byte or MSB), and the fine channel sets the
second 8 bits (the least significant byte or LSB) of the 16-bit control byte. In other words, the fine channel
fine-tunes the position set by the course channel.
Speed control
TRACKING CONTROL
Tracking control for pan/tilt and the various effects is enabled by setting the speed channels, respectively 13
and 14 (channels 16 and 17 in 16-bit Extended mode) to 0.
With tracking control, the speed at which effects move is determined by the cross-fade time between two
positions or scenes. The controller divides the move into steps and updates the fixture with small changes
at the rate required to achieve the fade. The fixture “tracks” the changes and averages them with a digital
filter algorithm to provide smooth movement.
VECTOR CONTROL
Alternatively, with vector control, movement speed is determined by the speed values on channels 13 and
14 (channels 16 and 17 in 16-bit Extended mode). This provides a way to control speed on controllers
without cross-faders. Vector control also provides smoother movement, particularly at slow speeds, with
controllers that send slow or irregular tracking updates.
When using vector control, the cross-fade time must be 0.
BLACKOUT
When “blackout while moving” is selected on channels 13 and 14 (channels 16 and 17 in 16-bit Extended
mode), the shutter closes when the effect moves to make the transition invisible. The shutter opens when
the movement is complete.
PERSONALITY OVERRIDES
Channel 13 (channel 16 in 16-bit Extended mode) provides tracking values that allow you to override the
pan/tilt speed personality setting (PTSP in the control menu). Channel 14 (channel 17 in 16-bit Extended
mode) provides tracking values that allow you to override the shortcuts setting (SCUT in the control menu).
See the DMX table for details.
16
MAC 250 Krypton
OPTICAL
CONFIGURATION
Gobos
The MAC 250 Krypton accepts up to eight metal or glass gobos with an outside diameter of 22.5 mm and a
maximum image diameter of 17 mm.
STANDARD GOBO CONFIGURATION
The MAC 250 Krypton provides 7 gobos as shown below.
1
7
2
6
Position
Gobo
1
Eclipse
2
Fat bar
3
Fan
4
Happy Yins
5
Twisted triangle
6
Splash
7
Aflobet
Table 3: Standard gobos
5
3
4
Figure 3: MAC 250 Krypton gobo
CUSTOM GOBOS
For optimum performance, custom glass gobos for the MAC 250 Krypton should be made with the text,
logo, and similar artwork reversed on the coated side. Gobo types and dimensions are specified in on
“Gobos” on page 37.
REPLACING A GOBO
Danger!
Intense heat. Avoid contact by persons and materials. The exterior of the fixture can get
very hot - up to 120° C (248° F). Disconnect the fixture from AC power and allow it to cool
for at least 45 minutes before handling.
Do not removing covers while the fixture is powered on as this exposes dangerous live
electrical circuits, hot surfaces, and a lamp under high pressure.
1
Disconnect the fixture from AC power and allow it to cool.
Optical configuration
17
2
Remove the top cover of the fixture head using a flathead screwdriver to loosen the four quarter-turn
screws. The top and bottom cover look the same, but the top cover is found by checking if the text on the
back of the head is oriented correctly (top) or not (bottom) as illustrated here.
mm
fla na
to lumi e
e
il t t
c
tan to ien
dis nce mb ce to
a fa
m ista
u
r
m
d
nim m mu su
Mi imu axi rior
M xte
n
Mi
E
18
3
Turn the gobo wheel to access the desired position.
4
Remove the gobo holder from the gobo wheel.
5
Squeeze the ends of the retention spring together and remove. Push the gobo out from the back and
remove.
6
Orient the gobo as shown in “Gobo orientation” on page 19 and insert the replacement gobo into the holder.
Secure the gobo with the retention spring.
MAC 250 Krypton
7
Insert the gobo holder back in the gobo wheel using a small flathead screwdriver to lift the retaining blades.
8
Replace the cover before applying power.
GOBO ORIENTATION
When an object is held up to the
coated side there is no space
between the object and its
reflection. The back edge of the
gobo cannot be seen when
looking through the coated side.
Smooth side towards lamp
When an object is held up to the
uncoated side there is a space
between the object and its reflection.
The back edge of the gobo can be
seen when looking through the
uncoated side.
Textured side towards stage
Reflective side towards lamp
Black side towards stage
Image/text Gobos
Metal Gobos
Textured Glass Gobos
Coated Glass Gobos
Figure 4 shows the correct orientation for different gobo types. When in doubt, install gobos with the more
reflective side towards the lamp.
Coated side towards lamp
Uncoated side towards stage
Reversed image towards
lamp
True image towards stage
Figure 4: Gobo orientation
Optical configuration
19
Color filters
STANDARD CONFIGURATION
The MAC 250 Krypton provides 12 dichroic color filters as shown below.
Position
1
12
11
2
10
3
4
9
Color
1
CTC
2
Yellow 603
3
Blue 104
4
Pink 312
5
Green 206
6
Blue 108
7
Red 301
8
Magenta 507
9
Blue 101
10
Orange 306
11
Dark green
12
Purple 502
5
8
6
7
Figure 5: MAC 250 Krypton color
REPLACING A COLOR FILTER
Danger!
Intense heat. Avoid contact by persons and materials. The exterior of the fixture can get
very hot - up to 120° C (248° F). Disconnect the fixture from AC power and allow it to cool
for at least 45 minutes before handling.
Do not removing covers while the fixture is powered on as this exposes dangerous live
electrical circuits, hot surfaces, and a lamp under high pressure.
1
Disconnect the fixture from AC power and allow it to cool.
2
Remove the top cover. The top and bottom cover look the same, but the top cover is found by checking if
the text on the back of the head is oriented correctly (top) or not (bottom).Remove the top cover of the
fixture head using a flathead screwdriver to loosen the four quarter-turn screws. The top and bottom cover
look the same, but the top cover is found by checking if the text on the back of the head is oriented correctly
(top) or not (bottom) as illustrated here.
m
lam ina
of
e t illumt te
c
tan to ien
dis nce mb ce to
a
m ista
u
m rfa
d
nim m mu su
Mi imu axi rior
M xte
n
Mi
E
3
20
MAC 250 Krypton
4
Turn the color wheel to access the desired color filter. Press the
filter forwards slightly to release it and then grasp it by the edges
and remove.
5
To insert a filter, slide it under the retention spring until it snaps into
place.
6
Replace the top cover before applying power.
B
A
Figure 5: Filter replacement
Prism
The standard 3-facet prism can be replaced with optional five- and nine-facet prisms. See “Accessories” on
page 38 for part numbers.
REPLACING THE PRISM
Danger!
Intense heat. Avoid contact by persons and materials. The exterior of the fixture can get
very hot - up to 120° C (248° F). Disconnect the fixture from AC power and allow it to cool
for at least 45 minutes before handling.
Do not removing covers while the fixture is powered on as this exposes dangerous live
electrical circuits, hot surfaces, and a lamp under high pressure.
1
Disconnect the fixture from AC power and allow it to cool.
2
Remove the top cover. The top and bottom cover look the same, but the top cover is found by checking if
the text on the back of the head is oriented correctly (top) or not (bottom).Remove the top cover of the
fixture head using a flathead screwdriver to loosen the four quarter-turn screws. The top and bottom cover
look the same, but the top cover is found by checking if the text on the back of the head is oriented correctly
(top) or not (bottom) as illustrated here.
mm
fla na
to lumi e
e
l
i
c
tt
tan to ien
dis ance mb ce to
a
um dist m rfa
nim m mu su
Mi imu axi rior
M xte
n
i
M
E
Optical configuration
21
3
Using a flathead screwdriver, remove the two retaining plates (only one - at position A - is illustrated here)
holding the prism module in place. Disconnect the cables (at positions marked B) from the PCBs on the
prism module.
A
B
B
22
4
Lift the prism module out of the fixture.
5
Using a Philips screwdriver, remove the half-circle shaped plate that holds the prism into place (as indicated
in this illustration).
6
Remove the rubber belt to free the prism and replace it with a compatible rotating prism (contact your Martin
dealer for a list of available prisms).
MAC 250 Krypton
7
Replace the rubber drive belt over the rotating prism and screw the half-circle shaped plate into place. The
prism should be able to rotate freely.
8
Reinsert the prism module into the fixture, reattach the leads (these are numbered) to the PCBs, and screw
the retaining plates into place.
9
Replace the top cover using a flathead screwdriver to tighten the four quarter-turn screws.
10 Connect the fixture to AC power.
Optical configuration
23
SERVICE
The MAC 250 Krypton requires regular maintenance to keep performing at their peak. Excessive dust,
grease, and smoke fluid buildup degrades performance and causes overheating and damage that is not
covered by the warranty. The maintenance schedule will depend on the application and should be
discussed with your Martin distributor. Refer any service that is not described here to a professional
technician.
Danger!
Intense heat. Avoid contact by persons and materials. The exterior of the fixture can get
very hot - up to 120° C (248° F). Disconnect the fixture from AC power and allow the it to
cool for at least 45 minutes before handling.
Do not removing covers while the fixture is powered on as this exposes dangerous live
electrical circuits, hot surfaces, and a lamp under high pressure.
Lamp replacement
Lamp life will vary; the rated life is an average figure that is based on the manufacturer’s test cycle. For
maximum lamp life, avoid excessive strikes and always allow the lamp to burn for at least 5 minutes before
turning it off.
To reduce the risk of lamp explosion, which may damage the fixture, never exceed the lamp’s rated life
(2000 hours) by more than 25 percent.
Replace the lamp when:
• it strikes with difficulty or not at all, or is in any other way defective
• usage exceeds the manufacturer’s “replace before” hours. See Table 1.
Refer to “Lamp installation” on page 6 for the lamp replacement procedure.
Cleaning
OPTICAL COMPONENTS
Use care when cleaning optical components. The surface on dichroic filters is achieved by means of special
multi-layer coatings and even small scratches may be visible. Residues from cleaning fluids can bake onto
components and ruin them.
1
Allow the components to cool completely.
2
Wash dirty lenses and filters with isopropyl alcohol. A generous amount of regular glass cleaner may also
be used, but no residues may remain.
3
Rinse with distilled water. Mixing the water with a small amount of wetting agent such as Kodak Photoflo will
help prevent streaking and spotting.
4
Dry with a clean, soft and lint-free cloth or blow dry with compressed air.
FAN
To maintain adequate cooling it is important that the fan be cleaned regularly. It can be cleaned with a soft
brush, vacuum, or compressed air.
24
MAC 250 Krypton
Lubrication
Use only silicone lubricant, Martin P/N 37302003 (500 ml) or P/N 37302004 (200 ml, in applicator bottle).
No other lubricant is approved for use. When applying lubricant, always remove excess and do not get oil
on other parts.
1
Check the focus mechanism and apply a drop of lubricant to the 3 metal slides if movement is rough.
2
Lubricate the rotating-gobo bearings if movement is rough on slow rotation or if they become noisy. Apply a
few drops of oil to each bearing from the lamp side of the wheel.
Replacing fuses
MAIN FUSE
The main fuse holder is built in to the mains input socket. Never replace the fuse with one of a different
rating!
1
Unplug the mains cable from the input socket.
2
Pry open the fuse holder and remove the fuse.
3
Replace the fuse with one of the same type and rating. The fuse rating is listed on serial number label.
4
Close the fuse holder and replace the mains cable.
POWER SUPPLY FUSES
There are two fuses for the low-voltage power supplies located on the printed circuit board. If one or more of
the green LEDs on the PCB does not light, one of these fuses may be blown. If all three LEDs are lit, the
low-voltage power supplies are functioning correctly.
Have the fixture serviced by a Martin service technician if the problem persists.
1
Disconnect the fixture from AC power.
2
Remove the left-side yoke cover (when looking at the head in the text in the upright position from the back
as indicated in the illustration) to access the PCB.
m
lam ina
of
e t illumt te
c
tan to ien
dis nce mb ce to
a
m ista
u
m rfa
d
nim m mu su
Mi imu axi rior
e
M xt
n
Mi
E
3
Carefully remove and check the two fuses located in the bottom of the PCB (see “Circuit board connections”
on page 36). Replace as necessary with fuses of the same size and rating (see page 37).
4
Re-attach the yoke cover.
Service
25
Updating software
The latest MAC 250 Krypton firmware is available from the support area of the Martin web site at
www.martin.dk. It can be installed via the serial data link using a supported Martin uploader such as the
MP-2, or via a LightJockey 4064 ISA DMX interface.
Note: Intermediate control systems such as the Martin Lighting Director (MLD) and the Martin Matrix must
be bypassed when updating fixture software via the DMX link. These systems do not relay the update code
correctly because it is not a DMX-compliant signal.
NORMAL UPDATE
To update fixture software, connect an upload device to the fixture just like a DMX controller and perform a
DMX mode upload as described in the uploader’s documentation. There is no need to isolate the MAC 250
Kryptons from other types of fixtures on the serial link.
When the upload is completed (and when booting up) the MAC 250 Krypton performs a check-sum test of
the flash memory and then resets. If the firmware is corrupted a check-sum error (C S E R ) occurs. A few
seconds later the fixture displays U PL d and is ready for a new DMX-mode upload.
In the unlikely event that a software upload is interrupted, the fixture must be powered off for at least 10
seconds to force the check-sum test. You can repeat the DMX-mode upload as soon as U P L d is
displayed.
BOOT SECTOR UPDATE
If the normal update procedure fails or the software update notes call for a boot-sector update, install new
software as follows.
1
Disconnect the fixture from AC power.
2
Remove the left-side yoke cover (when looking at the head in the text in the upright position from the back
as indicated in the illustration) to access the PCB.
26
3
The boot sector jumper is located next to the plug for the control
panel data cable. Move the jumper to the Init setting. Verify that
the Flash Write jumper is in the Enable position. See the
diagram in “Circuit board connections” on page 36.
4
Apply power and perform a boot-mode upload as described in
the uploader manual.
5
Disconnect the fixture from AC power. Move the jumper back to
the Lock setting.
6
Re-attach the yoke cover.
MAC 250 Krypton
front
m
lam a
o f umin
t
ce ill t te
tan to ien
dis ance mb ce to
um dist m a rfa
nim m mu su
Mi imu axi rior
M xte
n
Mi
E
Lock
Init
DMX
16 Bt
(16 Bit Mode)
16 Ex
(16 Bit Extended) Value
Function
0-7
8 - 19
20 - 28
29 - 31
31 - 39
39 - 47
47 - 50
50 - 58
58 - 65
66 - 73
74 - 75
75 - 76
76 - 77
77 - 78
78 - 79
80 - 81
82 - 85
85 - 89
89 - 93
93 - 97
97 – 100
Shutter, Strobe, Reset, Lamp On/Off
Shutter closed
Shutter open
Strobe, fast → slow
Shutter open
Opening pulse, fast → slow
Closing pulse, fast → slow
Shutter open
Random strobe, fast
Random strobe, medium
Random strobe, slow
Shutter open
Random opening pulse, fast
Random opening pulse, slow
Random closing pulse, fast
Random closing pulse, slow
Shutter open
Reset fixture
Shutter open
Lamp on
Shutter open
Lamp off
2
0 - 255
0 – 100
Dimmer
Closed → open
3
0-255
0-100
1If
DMX Reset is disabled in the menu,
a reset command can only be
executed if the CTC filter is selected,
the prism is on (not rotating) and the
open gobo is selected.
A 5 second delay can be given to the
reset command from the fixture menu
under, dRES.
2If DMX Lamp Off is disabled in the
menu, a lamp off command can only
be executed if the CTC filter is
selected, the prism is on (not rotating)
and the open gobo is selected.
3
Percent
0 - 19
20 - 49
50 - 72
73 - 79
80 - 99
100 - 119
120 - 127
128 - 147
148 - 167
168 - 187
188 - 190
191 - 193
194 - 196
197 - 199
200 - 202
203 - 207
208 - 217
218 - 227
228 - 237
238 - 247
248 - 255
1
2
A
PROTOCOL
4
Dimmer Fine (Lowest Significant Byte)
Closed → open
Color
Continuous Scroll: full color positions:
White
CTC
Yellow 603
Blue 104
Pink 312
Green 206
Blue 108
Red 301
Magenta 507
Blue 101
Orange 306
Dark green
Purple 502
White
0
11
22
33
44
55
66
77
88
99
110
121
132
143
0
4
9
13
17
22
26
30
35
39
43
47
52
56
156 – 159
160 – 163
164 – 167
168 – 171
172 – 175
176 – 179
180 – 183
184 – 187
188 – 191
192 – 195
196 – 199
200 – 203
204 – 207
61 – 63
63 – 64
64 – 65
66 – 67
67 – 68
69 – 70
70 – 72
72 – 73
74 – 75
75 – 76
77 – 78
78 – 79
80 – 81
Stepped Scroll
Purple 502
Dark green
Orange 306
Blue 101
Magenta 507
Red 301
Blue 108
Green 206
Pink 312
Blue 104
Yellow 603
CTC
White
208 – 226
227 – 245
82 – 88
89 – 96
Continuous Rotation
CW, fast → slow
CCW, slow → fast
246 – 248
249 – 251
252 – 255
96 – 97
98 – 98
99 – 100
Random color
Fast
Medium
Slow
DMX protocol
27
5
0 - 255
0-4
5 - 10
11 - 15
16 - 20
21 - 25
26 - 30
31 - 35
36 - 42
4
6
43 - 50
51 - 58
59 - 65
66 - 73
74 - 81
82 - 89
90 - 96
97 - 104
0 - 100
Color (Lowest Significant Byte)
0-2
2-4
4-6
6-8
8 - 10
10 - 12
12 - 14
14 - 16
Rotating Gobo selection and shake
Indexing: set position on channel 5 in 16 bt mode or
channel 6 in 16 Ex mode
Open gobo
Gobo 1
Gobo 2
Gobo 3
Gobo 4
Gobo 5
Gobo 6
Gobo 7
17 - 20
20 - 23
23 - 26
26 - 29
29 - 32
32 - 35
35 - 38
38 - 41
Rotation: set rotation speed on channel 5 in 16 bt
mode or channel 6 in 16 Ex mode
Open gobo
Gobo 1
Gobo 2
Gobo 3
Gobo 4
Gobo 5
Gobo 6
Gobo 7
105 - 119
120 - 134
135 - 149
150 - 164
165 - 179
180 - 194
195 - 209
41 - 46
47 - 52
53 - 58
59 - 64
65 - 70
70 - 76
76 - 82
210 - 232
233 - 255
82 - 91
91 - 100
Rotation with shake, slow → fast: set rotation speed
on channel 5 in 16 bt mode or channel 6 in 16 Ex
mode
Gobo 7, Shake slow → fast
Gobo 6, Shake slow → fast
Gobo 5, Shake slow → fast
Gobo 4, Shake slow → fast
Gobo 3, Shake slow → fast
Gobo 2, Shake slow → fast
Gobo 1, Shake slow → fast
Continuous scroll
CW slow → fast
CCW fast → slow
Gobo rotation (active when you select gobo on
channel 4 in 16 bt mode or channel 5 in 16 Ex mode)
5
28
0 - 255
0 - 100
Index position 0 - 395
0-2
3 - 127
128 - 252
253 - 255
0-1
1 - 50
50 - 98
99 - 100
Continuous rotation (direction and speed)
No rotation
CW, slow → fast
CCW, fast → slow
No rotation
7
6
8
0 – 255
0 - 100
Gobo Rotation ((Lowest Significant Byte)
7
9
0 - 255
0 - 100
Focus
Infinity → 2 meters
10
0 - 255
0 - 100
Focus (Lowest Significant Byte)
0 - 19
20 - 79
80 - 89
90 - 149
150 - 215
0-7
8 - 31
31 - 35
35 - 58
59 - 84
Prism
Prism off
Rotating prism, CCW fast à slow
No rotation
Rotating prism, CW slow à fast
Prism off
8
11
216 - 220
221 - 225
226 - 230
231 - 235
236 - 240
241 - 245
246 - 250
251 - 255
84 - 86
87 - 88
89 - 90
91 - 92
93 - 94
95 - 96
96 - 98
98 - 100
Prism/Gobo Macros
Macro 1
Macro 2
Macro 3
Macro 4
Macro 5
Macro 6
Macro 7
Macro 8
9
12
0 - 255
0 - 100
Pan
Left → right (128 = neutral)
10
13
0 - 255
0 - 100
Pan Fine (Lowest Significant Byte)
Left → right
11
14
0 - 255
0 – 100
Tilt
Left → right (128 = neutral)
MAC 250 Krypton
12
13
14
15
0 - 255
0 – 100
Tilt Fine (Lowest Significant Byte)
Left → right
16
0-2
3 - 245
246 - 248
249 - 251
252 - 255
0-1
1 - 96
96 - 97
98 - 98
99 - 100
Pan/Tilt Speed
Tracking
Fast → slow
Tracking, PTSP NORM (menu override)
Tracking, PTSP FAST (menu override)
Blackout while moving
0-2
3 - 245
246 - 251
252 - 255
0-1
1 - 96
96 - 98
99 - 100
Effects Speed
Dimmer, focus
Tracking mode
Fast → slow
Tracking
Maximum speed
0-2
3 - 245
246 - 248
249 - 251
252 - 255
0-1
1 - 96
96 - 97
98 - 98
99 - 100
Color
Tracking mode
Speed, fast → slow
Tracking, SCUT OFF (control menu override)
Tracking, SCUT ON (control menu override)
Blackout while moving
0 - 245
246 - 248
249 - 251
252 - 255
0 - 96
96 - 97
98 - 98
99 - 100
Gobo selection
Normal (no blackout)
Normal, SCUT OFF (control menu override)
Normal, SCUT ON (control menu override)
Blackout while moving
0-2
3 - 245
246 - 251
252 – 255
0-1
1 - 96
96 - 98
99 - 100
Indexed gobo rotation (only if gobo type = indexed)
Tracking mode
Fast à slow
Tracking
Blackout while moving
0 - 251
252 - 255
0 - 98
99 - 100
Prism
Normal (no blackout)
Blackout while moving
17
DMX protocol
29
CONTROL
B
MENU
Options displayed in bold represent the default settings.
Menu
Item
Options
Notes (Default settings in bold print)
Ad d R
-
1- 5 12
DMX address
16 B T
16 Bit
16 E X
16 Bit extended
ON
Map DMX pan control to tilt channel and vice versa.
OF F
Normal pan and tilt control
ON
Reverse DMX pan control, right → left
OF F
Normal pan control, left → right
ON
Reverse DMX tilt control, down → up
OF F
Normal tilt control, up → down
NO R M
Default pan/tilt speed
FA S T
Maximum pan/tilt speed (position may be less precise)
SL O W
Minimum pan/tilt speed
ON
Display remains on
2 MN
Display extinguishes 2 minutes after last key press
10MN
Display extinguishes 10 minutes after last key press
AUTO
Automatic display dimming
10 - 10 0
Set display intensity manually
ON
Enable DMX lamp off command
OF F
Disable DMX lamp off command
ON
Enable DMX reset command
OF F
Disable DMX reset command
5S E C
Reset from Controller
ON
Lamp strikes automatically within 90 seconds of power on
OF F
No automatic lamp strike
dM X
Lamp strikes if DMX is present, douses 15 mins. after it’s
missing
ON
Effect wheels turn shortest distance
OF F
Effect wheels do not cross open position
DI M 1
0-100%
DI M 2
Tungsten
LO A D
Return all personality settings (not calibrations) to factory
defaults
PS E T
PA T I
SW AP
PI NV
TI NV
PT S P
PE R S
dI SP
dI NT
dL OF
dR ES
AL ON
SC UT
dI CU
dF S E
30
FA CT
MAC 250 Krypton
IN F O
RS E T
Hours of operation since counter reset. To reset, display
counter and press [up] for 5 seconds.
TO T L
Total hours of operation with lamp on since fabricated
RS E T
Lamp hours since counter reset. To reset, display counter
and press [up] for 5 seconds.
TO T L
Total number of lamp strikes since fabricated
RS E T
Number of lamp strikes since counter reset. To reset,
display counter and press [up] for 5 seconds.
HE A D
Head temperature
BA S E
Base Temperature
VE R
X. X
CPU firmware version
-
RATE
DMX packets per second
qUAL
Percentage of data received without errors
ST C O
Decimal value of the DMX start code.
SHUT..EFSP
DMX value (from 0 → 255) received for each channel.
SH U T
Shutter value
DI M
Dimmer value
CO L
Color wheel value
GO B O
Fixed gobo value
RO G O
Rotating gobo value
FO C
Focus value
PR I S
Prism value
PA N C
Coarse pan value
PA N F
Fine pan value
TI L C
Coarse tilt value
TI L F
Fine tilt value
PT S P
Pan/tilt speed value
EF S P
Effect speed value
TI ME / L HR
TI ME / L ST
TE MP
dM X L
Control menu
31
MA N
RS T
-
Reset fixture
L ON
-
Lamp on
LoFF
-
Lamp off
SHUT
OPEN
Open shutter
CLOS
Close shutter
STRF
Fast strobe
STRM
Medium strobe
STRS
Slow strobe
dIM
0-255
Dimmer
COL
OPEN
Color wheel in open position.
12
C1-C12
Color wheel positions 1 → 12.
CW F
Clockwise rotation - fast
CCWF
Counter-clockwise rotation - fast
CW M
Clockwise rotation - medium
CCWM
Counter-clockwise rotation - medium
CW S
Clockwise rotation - slow
CCWS
Counter-clockwise rotation - slow
RNdF
Random color - fast
RNdM
Random color - medium
RNdS
Random color - slow
OPEN
Gobo wheel in open position
g1 I-g7 I
Indexed gobos 1-7
g1 R-g7 R
Rotating gobos 1-7
g1RS-g7RS
Rotating gobo shake 1-7
CW F
Clockwise rotation, fast
CCWF
Counter-clockwise rotation, fast
CW M
Clockwise rotation, medium
CCWM
Counter-clockwise rotation, medium
CW S
Clockwise rotation, slow
CCWS
Counter-clockwise rotation - slow
0-255
Clockwise rotation of gobo wheel. Slow - fast.
gObO
I/S
32
MAC 250 Krypton
ON
Prism in
OFF
Prism out
CWF
Clockwise rotation - fast
CCWF
Counter-clockwise rotation - fast
CWM
Clockwise rotation - medium
CCWM
Counter-clockwise rotation - medium
CWS
Clockwise rotation - slow
CCWS
Counter-clockwise rotation - slow
FOC
0-255
Focus, Infinity-Near
PAN
0-255
Pan, Left-Right
TILT
0-255
Tilt, Up-Down
TS E Q
-
RU N
Run a general test of all effects
UT I L
FEbA
ON
Magnetic sensors monitor the positions of the color wheel,
gobo wheel, and rotating gobos. If they detect an error, the
shutter closes while the effect resets.
OF F
Effect feedback disabled.
ON
Enable on the fly reset of magnetically indexed effects
OF F
Disable on the fly reset of magnetically indexed effects
Ad j
-
Not implemented
CA L
-
Not implemented
dF OF
SU R E
Return all offsets to the default settings
PC bT
Le d
PCB test for service use only.
UP Ld
SU R E
Manually set fixture to software update mode
MA N
(cont.)
PRIS
(P r es s
an d h o ld
En t er
mo r e
th a n 3
se c . to
ac c es s)
EF Fb
Control menu
33
ERROR
C
MESSAGES
Display readout
Appears if...
What to do
MERR (Memory error)
...the EEPROM memory cannot be
read.
• Contact service technician.
****
... there is no communication between
the control panel and motherboard.
This appears briefly when switching on
the fixture.
• Check fuses.
• Check cable between control panel and
motherboard.
• Reinstall software.
• Contact service technician.
COER (Color wheel time-out)
RGER (Rot. gobo time-out)
FGER (Fixed gobo time-out)
GOER (Gobo index time out)
...the magnetic-indexing circuit
malfunctions (e.g. sensor defective or
magnet missing).
• After the time-out, the effect in question
stops in a random position.
• Contact service technician.
LERR
...the lamp cannot be struck.
• Replace the lamp
shER
....there is a short circuit and the lamp
is struck without a command.
• Contact service technician.
bTER
...the temperature in the base is too
high
• Ensure that the fans are clear and functioning and that the ambient temperature
does not exceed 40° C (104° F)
• Contact service technician if the problem
persists.
PAER
...if there is a pan error and the sensor
cannot find the pan index point
• After the time-out, the fixture stops in a
random position.
• Contact service technician.
TIER
...if there is a tilt error and the sensor
cannot find the pan index point
• After the time-out, the fixture stops in a
random position.
• Contact service technician.
dRER
...if there is a drive current error.
• Contact service technician.
dPER
...if there is a display programming
error.
• Contact service technician.
Table 5: Error messages
34
MAC 250 Krypton
D
TROUBLESHOOTING
Problem
Probable cause(s)
Remedy
One or more of the fixtures
is completely dead.
No power to fixture.
• Check that power is switched on and cables are
plugged in.
Primary fuse blown.
• Replace fuse.
Secondary fuse(s) blown (located on
PCB inside base).
• Check fuses on PCB and replace.
Fixtures reset correctly but
all respond erratically or
not at all to the controller.
The controller is not connected.
• Connect controller.
XLR pin-out of the controller does not
match pin-out of the first fixture on the
link (i.e. signal is reversed).
• Install a phase-reversing cable between the controller and the first fixture on the link.
Fixtures reset correctly but
some respond erratically
or not at all to the
controller.
Poor data quality
• Check data quality (page 13). If much under 100
percent, the problem may be a bad data link connection, poor quality or broken cabling, missing
termination, or a defective fixture disturbing the
link.
Bad data link connection
• Inspect connections and cables. Correct poor
connections. Repair or replace damaged cables.
Data link not terminated with 120Ω
termination plug.
• Insert termination plug in output jack of the last
fixture on the link.
Incorrect addressing of the fixtures.
• Check address setting.
One of the fixtures is defective and
disturbs data transmission on the link.
• Bypass one fixture at a time until normal operation is regained: unplug both connectors and connect them directly together.
• Have the defective fixture serviced by a qualified
technician.
XLR pin-out on fixtures does not
match (pins 2 and 3 reversed).
• Install a phase-reversing cable between the fixtures or swap pins 2 and 3 in the fixture that
behaves erratically.
Shutter closes suddenly.
The color wheel, gobo wheel, or a
gobo has lost its index position and the
fixture is resetting the effect.
• Contact Martin technician for service if the problem persists.
No light and “LERR” error
message displayed.
The power supply settings do not
match local AC voltage and frequency.
• Disconnect fixture. Check settings (“AC power” on
page 7) and correct if necessary.
Lamp missing or blown
• Disconnect fixture and replace lamp.
Fixture is too hot.
• Allow fixture to cool.
• Clean fan.
• Make sure air vents at control panel and front lens
are not blocked.
• Turn up the air conditioning.
The power supply settings do not
match local AC voltage and frequency.
• Disconnect fixture. Check settings (“AC power” on
page 7) and correct if necessary.
Lamp cuts out
intermittently.
Table 6: Troubleshooting
Troubleshooting
35
CIRCUIT
36
BOARD CONNECTIONS
MAC 250 Krypton
E
SPECIFICATIONS - MAC 250 KRYPTON
PHYSICAL
Base length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .375 mm (14.8 in)
Base width . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .315 mm (12.4 in)
Yoke width . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .393 mm (15.5 in)
Height . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .538 mm (21.2 in)
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22.4 kg (49 lbs)
AC POWER
Operating range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 - 250 V, 50/60 Hz
AC input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-prong IEC male socket
MAXIMUM POWER AND CURRENT
100 V, 50 Hz. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 319 W, 3.8 A, PF 0.8
100 V, 60 Hz. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 317 W, 3.4 A, PF 0.9
120 V, 50 Hz. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 320 W, 2.9 A, PF 0.9
120 V, 60 Hz. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 314 W, 2.7 A, PF 1.0
208 V, 50 Hz. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 320 W, 1.9 A, PF 0.8
208 V, 60 Hz. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 319 W, 1.7 A, PF 0.9
230 V, 50 Hz. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 323 W, 1.6 A, PF 0.9
230 V, 60 Hz. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 326 W, 1.5 A, PF 1.0
250 V, 50 Hz. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 326 W, 1.5 A, PF 0.9
250 V, 60 Hz. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 325 W, 1.4 A, PF 1.0
Note: Measurements have a margin of error of +/- 10%
V = volts, Hz = hertz, W = watts, A = amps, PF = power factor
THERMAL
Maximum ambient temperature (Ta) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40° C (104° F)
Maximum surface temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120° C (248° F)
INSTALLATION
Orientation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . any
Minimum distance to flammable materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.1 m (4 in)
Minimum distance to illuminated surfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.3 m (12 in)
FUSES
Main fuse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.3 A / 250 V, time-delay
Fuse F1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.3 A / 250 V, time-delay
Fuse F2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.0 A / 250 V, time-delay
LAMPS
Philips MSD 250/2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2000 hr, 9000K, 250 W
Osram HSD 250/78 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3000 hr, 7800K, 250 W
GE CSD 250/2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2000 hr, 9000K, 250 W
GOBOS
Outside diameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22.5 mm + 0/- 0.3 mm (0.886 in. +0/- 0.012 in)
Maximum image diameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 mm (0.669 in)
Maximum thickness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.8 mm (0.071 in)
Glass type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .high temperature Borofloat or better
Glass coating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . dichroic or enhanced aluminum
Metal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . aluminum (steel okay for short use)
CONTROL AND PROGRAMMING
Data input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .locking 3-pin and 5-pin XLR male sockets
Data output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . locking 3-pin and 5-pin XLR female sockets
Data pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pin 1 shield, pin 2 cold (-), pin 3 hot (+)
Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Opto-isolated RS-485
Protocols. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . USITT DMX-512 (1990)
DMX Channels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14/17
Specifications - MAC 250 Krypton
37
DESIGN STANDARDS
Canadian safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .CSA C22.2 NO 166
EU EMC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EN 50 081-1, EN 50 082-1
EU safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EN 60598-1, EN 60598-2-17
US safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ANSI/UL 1573
INCLUDED ITEMS
Omega bracket, MAC 250/300 1/4-turn
XLR cable, 5 m, black, 3-pin
Mains cable, 3 m, IEC 3-pin
User manual
ORDERING INFORMATION
MAC 250 Krypton . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P/N 90225600
ACCESSORIES
G-clamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P/N 91602003
Half-coupler clamp. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P/N 91602005
PHOTOMETRICS
Light output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4618 lumens
Field angle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20.6°
Measurement conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230 V, 50 Hz; no effects applied
Measurement source. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Philips MSD 250/2
Beam Diam eter as function of distance
7.00
6.00
Beam Diameter [m]
5.00
4.00
3.00
2.00
1.00
0.00
0
2
4
6
8
10
Distance [m ]
38
MAC 250 Krypton
12
14
16
18
Intensity as function of distance
1000000
100000
Intensity [Lux]
10000
1000
100
10
1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Distance [m]
Polar Plot
140000
120000
Candela
100000
80000
60000
40000
20000
0
0
2
4
6
8
10
12
Be am Angle [°]
Specifications - MAC 250 Krypton
39