Audiovox CA 3051 Installation guide

PROFESSIONAL
SERIES
Keyless Alarm
Installation Guide
ca 3051
ca3051 rev B. 2011 Audiovox Electronics Corporation. All rights reserved.
1
BEFORE YOU BEGIN
PROFESSIONAL INSTALLATION
STRONGLY RECOMMENDED
Installation Precautions:
Roll down window to avoid locking keys in vehicle during
installation
Avoid mounting components or routing wires near
hot surfaces
Avoid mounting components or routing wires near moving
parts
Tape or loom wires under hood for protection and
appearance
Use grommets when routing wires through metal surfaces
Use a Digital Multi Meter for testing and verifying circuits.
DO NOT USE A TEST LIGHT, OR "COMPUTER SAFE
PROBE" as these can set off air bags or damage vehicle
computers.
Technical Support (800) 421-3209
or go to
http://techservices.codesystems.com
2
ca3051 rev B. 2011 Audiovox Electronics Corporation. All rights reserved.
INSTALLATION OF THE MAJOR COMPONENTS
Control Module
Select a mounting location inside the passenger compartment (behind the dash),
and secure using the two screws provided. The control module can also be
secured in place using cable ties. Be certain that the chosen location will not
interfere with the proper operation of the vehicle. Avoid mounting the module to
or routing the wiring around the steering shaft/column, as the module or wiring
may wrap around or block the steering wheel preventing proper control of the
vehicle. Secure the module in the chosen location using cable ties or screws as
necessary. Do not mount the module in the engine compartment, as it is not
waterproof.
Siren
Select a location in the engine compartment that is not accessible from below the
vehicle. The selected location must be clear of hot or moving parts within the
engine compartment The siren must be pointed downward to prevent water
retention and the flared end must be pointed away from and out of the engine
compartment for maximum sound distribution. Before securing the siren, check
behind your chosen location to assure that the mounting screws will not
penetrate any factory wiring or fluid lines. Secure the siren mounting bracket
using #8 self taping screws or by first using the mounting bracket as a template,
scribe or mark the mounting holes. Drill the marked holes using a 1/8" drill bit,
then mount the siren using #8 sheet metal screws.
Dash Mounted LED
A small Red LED included in the kit will serve as a visual indicator of the alarm's
status. It should be installed in the dash, located where it can be easily seen
from outside the vehicle, yet not be distracting to the driver. Once a location has
been selected, check behind the panel for wire routing access, and to confirm
the drill will not damage any existing components as it passes through the panel.
Drill a 1/4 " hole, and pass the red and blue wires from the LED through the hole,
from the front of the panel. Firmly press the body of LED into the hole until fully
seated.
Valet/Programming/Override Switch
Select a mounting location that is within reach of the ignition switch, as this
switch in combination with the ignition switch, will be used to program the
certain features of the system. It is suggested that the switch be mounted to the
lower dash panel in the driver's area within reach of the driver.
ca3051 rev B. 2011 Audiovox Electronics Corporation. All rights reserved.
3
Two Stage Shock Sensor
Select a solid mounting surface for the shock sensor inside the passenger
compartment (behind the dash), and mount the sensor using cable ties, making
sure to allow access to the sensitivity adjustment potentiometer for use later in
the installation.
WIRING THE SYSTEM
RED
BATTERY 12V (+)
Connect this wire to a +12 Volt constant source found at the vehicles ignition
switch. This wire provides power for the control module.
ORANGE
GROUND WHEN ARMED
This wire is provides a 300mA output to control the starter disable relay. Connect
the orange wire to terminal 86 of the relay. Connect relay terminal 85 to an ignition
wire in the vehicle that is live when the key is in the ON and CRANK positions,
and off when the key is in the OFF position. (this is where the pink wire from the
alarm should be connected).
NOTE: This is a normally closed starter disable arrangement, and when power is
removed from the security system, the starter disable feature will not operate,
allowing the vehicle to start. Code Systems does not recommend using the
Orange wire to interrupt anything but the starting circuit of the vehicle.
WHITE
PARKING LIGHT OUTPUT (+/- 15 AMP MAX)
This wire is provided to flash the vehicle’s parking lights. Connect the white wire
to the output side of one of the vehicle’s parking lights.
WHITE/RED
PARKING LIGHT POLARITY INPUT
This wire is provided as a polarity input of the pulsed parking light output relay.
a) For vehicles with positive switching parking lights. Connect the White/Red
wire to a +12 VDC constant battery source.
b) For vehicles with negative switching parking lights. Connect the White/Red
wire to a solid chassis ground source.
4
ca3051 rev B. 2011 Audiovox Electronics Corporation. All rights reserved.
BROWN
SIREN / HORN OUTPUT
This output is available to be used as a constant ( + ) siren output OR a pulsed
( - ) horn output and is selectable by changing the jumper position on the main
module. Refer to the system layout on page 12 for location.
SIREN:
Connect the BLACK siren wire to a chassis ground using a ring terminal and self
tapping screw (not supplied).
Route the BROWN siren output wire from the control module through the firewall
and connect to the RED wire on the siren.
NOTE: Be sure to loom the siren wires, and seal the grommet.
HORN:
Locate the vehicle’s horn wire.
Verification: This wire will register at positive voltage and register
ground when the horn switch is pressed.
Connect the BROWN/BLACK wire to the vehicle’s horn wire.
BLACK
CHASSIS GROUND
Connect this wire to a solid, metal part of the vehicle’s chassis. Do not confuse
this wire with the thin black antenna wire that exits the control module
independently.
TAN/BLACK
TRUNK DISARM INPUT (+)
This wire will determine if the vehicle's trunk has been opened using the factory
(OEM) keyless entry transmitter, and prevent the alarm from triggering when the
factory (OEM) keyless entry transmitter is used. This wire requires a positive
trigger input and must be wired to the +12 volt trunk control wire from the
vehicles keyless entry system, or the switched +12 volt side of the vehicles trunk
release solenoid.
ca3051 rev B. 2011 Audiovox Electronics Corporation. All rights reserved.
5
GREY
(-) HOOD/TRUNK TRIGGER
This is an instant on ground trigger wire. It must be connected to the previously
installed hood and/or trunk pin switches.
GREEN
NEGATIVE DOOR TRIGGER INPUT
If the vehicle’s courtesy light switches have a (-) ground output when the door is
opened (GM and most Imports), you must connect the Green wire to the negative
output from one of the door switches.
PURPLE
POSITIVE DOOR TRIGGER INPUT
If the vehicle’s door courtesy light switches have a + 12 volt output when the
door is opened (most Fords and some Imports), you must connect the Purple wire
to the positive output from one of the door switches. In most cases, the Violet
wire will only needs to be connected to one door switch, no matter how many
doors the vehicle has.
YELLOW
IGNITION INPUT ( + )
Connect this wire to the ignition 1 wire from the ignition switch. This wire will
show +12 volts when the ignition key is turned to the to the ON, RUN and START
positions, and will have 0 volts when the key is turned to the OFF and
ACCESSORY positions.
ORANGE/GREEN
30 SECOND OUTPUT WHEN ARMED ( - )
OR PASSIVE DOOR LOCK OUTPUT (-)
This wire is programmable to provide either a 30 second pulsed output when the
system is ARMED or a pulsed ground output to the factory door lock control relay
for a passive door locking feature. The maximum current draw through these
outputs must not exceed 300 mA.
6
ca3051 rev B. 2011 Audiovox Electronics Corporation. All rights reserved.
3 Wire Ground Switched Door Locks
In this application, the Orange/Green wire provides a pulsed ground lock
output. Connect this wire to the wire that provides a low current ground
signal from the factory door lock switch to the factory door lock control
relay.
3 Wire Positive Switched Door Locks (Relay required see Diagram 1)
5 Wire Alternating 12 Volt (Relay required see Diagram 2)
Diagram 1
Lock
Fused + 12v
86
87
85
+ 12 Volts
87a
30
X
Lock Relay In Vehicle
Diagram 2
Lock
Fused + 12v
86
87
85
+ 12
Volts
87a
30
Door Lock Switch
Door Lock Motor
X
CUT HERE
ca3051 rev B. 2011 Audiovox Electronics Corporation. All rights reserved.
7
BLACK/WHITE
ILLUMINATED ENTRY OUTPUT 200 mA (-)
This wire provides a 30 second ground output whenever the system is disarmed
using the OEM transmitter, and pulses ground when the alarm is triggered. It is
used to provide the optional entry lighting feature, and will flash the vehicle's
interior light when the system is triggered. This is a transistorized, low current
output, and should only be used to drive an external relay.
3 PIN WHITE CONNECTOR
These wires will allow the Factory (OEM) transmitter to arm the system when the
LOCK button is pressed, and disarm the system when the UNLOCK button is
pressed.
LT BLUE/RED
ARM INPUT
Connect the Lt Blue/Red to the lock motor wire of the drives door actuator. The
lock motor wire will pulse +12 volts when the LOCK button is pressed on the
Factory (OEM) transmitter.
LT BLUE/BLACK
DISARM INPUT
Connect the Lt Blue/Black to the unlock motor wire of the drivers door actuator.
The unlock motor wire will pulse +12 volts when the UNLOCK button is pressed
on the OEM transmitter. For vehicles with two stage unlocking, the unlock motor
wire of the drivers door actuator will pulse +12 volts when the UNLOCK button is
pressed the first time (unlocking the drivers door), and will not show any pulses
the second time the UNLOCK button is pressed (unlocking all remaining doors) on
the OEM transmitter.
LT BLUE/GREEN
UNLOCK SENSE INPUT
Connect the Lt Blue/Green wire to the positive or negative unlock wire from the
door lock/unlock switch, or any passenger door unlock motor wire.
a). For vehicles with two stage unlocking, it is very important that the Lt Blue/
Black wire does not receive a pulse when the drivers door only is unlocked using
the OEM transmitter.
b). For vehicles with single stage unlocking (all doors unlock with one press of
UNLOCK on the OEM transmitter), connect the Lt Blue/Black to chassis ground.
Note: You can select the polarity of this input by changing DIP Switch #2
8
ca3051 rev B. 2011 Audiovox Electronics Corporation. All rights reserved.
ca3051 rev B. 2011 Audiovox Electronics Corporation. All rights reserved.
9
ADDITIONAL PORTS
LED PORT
Route the red and blue wires in the 2 pin white connector from the LED to the
control module, and plug it into the mating white connector on the side of the
module.
VALET / PROGRAMMING PORT
Route the 2 pin red connector from the override switch previously mounted to
the mating two pin connector on the module.
SHOCK SENSOR PORT
Route the 4 pin connector form the previously installed shock sensor to the
mating 4 pin connector of the module.
COMPLETING THE INSTALLATION
Adjusting the Shock Sensor: Gently turn the adjustment dial counter
clockwise to turn down the sensitivity and turn clockwise to turn up sensitivity.
Close the hood and trunk lids, and arm the alarm . Wait 6 seconds for the
accessories trigger zone to stabilize, then test the sensitivity adjust as needed
CAUTION: Never perform this test on the vehicle’s glass, as you may break the
window.
WARNING ! Setting the sensitivity too high can cause false alarms due to noise
vibrations from passing trucks and heavy equipment. To decrease sensitivity,
turn the adjustment screw counter clockwise.
Wire Dressing: Always wrap the alarm wires in convoluted tubing, or with a
spiral wrap of electrical tape. Secure these looms along the routing using cable
ties. This will ensure that the alarm wires are not damaged by falling onto hot or
sharp moving surfaces in the vehicle.
10
ca3051 rev B. 2011 Audiovox Electronics Corporation. All rights reserved.
PROGRAMMABLE FEATURES
Changing Programmable Features:
This system has several programmable features that may need to be changed
based on a specific vehicle or a customer's preference. Programmable
features can be changed using the bank of dip switches located on the side of
the control module. To change a setting carefully flip the dip switch using a
small screwdriver or pick. Use the chart below as reference.
Dip Switch Feature Bank
ON
OFF
1
Passive Lock / 30 Sec. Output when Armed
30 Sec. Output when Armed
Passive Door Lock
2
Arm / Disarm Input Polarity
Positive
Negative
3
Unlock Switch Sense Input Polarity
Positive
Negative
4
N/A
5
Passive Arming
Passive
Active
6
Entry Delay
15 Second Delay
Instant
7
Siren / Horn Output
Siren
Horn
8
Door Ajar Warning
Instant
30 Second
Default Settings are in BOLD
ca3051 rev B. 2011 Audiovox Electronics Corporation. All rights reserved.
11
CA 3051
1-8
12
ca3051 rev B. 2011 Audiovox Electronics Corporation. All rights reserved.
(-)
(+)
ARM INPUT
DISARM INPUT
UNLOCK SENSE INPUT
BATTERY 12V ( + )
SIREN HORN OUTPUT
CHASSIS GROUND
DOOR TRIGGER INPUT ( - )
DOOR TRIGGER INPUT ( + )
TRUNK DISARM INPUT ( + )
HOOD / TRUNK TRIGGER INPUT ( - )
IGNITION INPUT ( + )
GROUND WHEN ARMED OUTPUT
SELECTABLE PULSED OUTPUT ( - )
ILLUMINATED ENTRY OUTPUT 200ma ( - )
PARKING LIGHT INPUT
PARKING LIGHT OUTPUT
SHOCK SENSOR PORT
L.E.D. PORT
RED
BROWN
BLACK
GREEN
PURPLE
TAN/BLACK
GRAY
YELLOW
ORANGE
ORANGE/GREEN
BLACK/WHITE
WHITE/RED
WHITE
SIREN / HORN OUTPUT POLARITY JUMPER
LT BLUE/RED
LT BLUE/BLACK
LT. BLUE/GREEN
VALET / PROGRAMMING PORT
ca3051 rev B. 2011 Audiovox Electronics Corporation. All rights reserved.
13
Audiovox Electronics Corporation.
Customer Service 1-800-421-3209
WWW.CODE-ALARM.COM
FCC COMPLIANCE
This device complies with Part 15 of the FCC rules and with RSS-210 of
Industry Canada. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including any interference
that may cause undesired operation.
Warning!
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
14
ca3051 rev B. 2011 Audiovox Electronics Corporation. All rights reserved.