ADJ InnoRollLED Instruction manual

Inno Roll LED
General Information
Unpacking: Thank you for purchasing the Inno Roll LED by Ameri-
can DJ®. Every Inno Roll LED has been thoroughly tested and has
been shipped in perfect operating condition. Carefully check the shipping carton for damage that may have occurred during shipping. If the
carton appears to be damaged, carefully inspect your fixture for any
damage and be sure all equipment necessary to operate the unit has
arrived intact. In the event damage has been found or parts are missing, please contact our toll free customer support number for further
instructions. Please do not return this unit to your dealer without contacting customer support first.
Introduction: The Inno Roll LED is a 8 channel DMX intelligent LED
scanner. The Inno Roll LED has three operating modes; a sound active,
show mode, DMX controlled. The Inno Roll LED can operate as a stand
alone fixture or in a Master/Slave configuration. For best results use
fog or special effects smoke to enhance the beams projections.
Customer Support: American DJ® provides a toll free customer
support line, to provide help and to answer any question should you
encounter problems during your set up or initial operation. You may
also visit us on the web at www.americandj.com for any comments or
suggestions. Service Hours are Monday through Friday 8:00 a.m. to
4:30 p.m. Pacific Standard Time.
Voice:
(800) 322-6337
Fax: (323) 582-2941
E-mail: support@americandj.com
To purchase parts online visit http://parts.americandj.com
Warning! To prevent or reduce the risk of electrical shock or fire, do
not expose this unit to rain or moisture.
Warning! This may cause severe eye damage. Avoid looking directly
into the light source at all times!
User Instructions
Rev. 6/12
American DJ® - www.americandj.com - Inno Roll LED Instruction Manual Page 2
Inno Roll LED
General Instructions
To optimize the performance of this product, please read these
operating instructions carefully to familiarize yourself with the basic
operations of this unit. These instructions contain important safety
information regarding the use and maintenance of this unit. Please
keep this manual with the unit, for future reference.
Inno Roll LED
Features
• 8 DMX Channels
• 3 Operating Modes - Sound Active, Show Mode, & DMX Control
• Internal Microphone
• Digital Display for Address and Function Setting
• UC3 Controller (Not Included)
• 6 Preprogrammed Shows
• 8 Colors + White
• 6 Replaceable Gobos + Spot
Inno Roll LED Warranty Registration
The Inno Roll LED carries a 3 year (1095 days) limited warranty.
Please fill out the enclosed warranty card to validate your purchase
and warranty. You may also register your product online at www.
americandj.com. All returned service items whether under warranty or
not, must be freight pre-paid and accompany a return authorization
(R.A.) number. If the unit is under warranty you must provide a copy
of your proof of purchase invoice. Please contact American DJ® customer support for a R.A. number.
Inno Roll LED
Handling Precautions
Caution! There are no user serviceable parts inside this unit. Do not
attempt any repairs yourself, doing so will void your manufactures
warranty. In the unlikely event your unit may require service please
contact American DJ®.
During operation the housing may become extremely hot. Avoid touching the unit with bare hands while in use.
American DJ® will not accept any liability for any resulting damages
caused by the non-observance of this manual or any unauthorized
modification to this unit.
American DJ® - www.americandj.com - Inno Roll LED Instruction Manual Page 3
Inno Roll LED
Safety Precautions
For Your Own Personal Safety, Please Read and Understand This
Manual Completely Before You Attempt To Install Or Operate
This Unit!
•To reduce the risk of electrical shock or fire, do not expose this unit rain or moisture
•Do not spill water or other liquids into or on to your unit.
•Do not attempt to operate this unit if the power cord has been
frayed or broken.
•Do not attempt to remove or break off the ground prong from the electrical cord. This prong is used to reduce the risk of electrical shock and fire in case of an internal short.
•Disconnect from main power before making any type of connection.
• Do not remove the cover under any conditions. There are no user serviceable parts inside.
•Never operate this unit when it’s cover is removed.
•Always be sure to mount this unit in an area that will allow proper ventilation. Allow about 6” (15cm) between this device and a wall.
•Do not attempt to operate this unit, if it becomes damaged.
•This unit is intended for indoor use only, use of this product outdoors voids all warranties.
•Always mount this unit in safe and stable matter.
•Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience recep-
tacles, and the point where they exit from the appliance.
• Cleaning -The fixture should be cleaned only as recommended by the manufacturer. See page 20 for cleaning details.
•Heat -This fixture should be situated away from heat sources such
as radiators, heat registers, stoves, or other appliances (including
amplifiers) that produce heat.
•The fixture should be serviced by qualified service personnel when:
A. Objects have fallen, or liquid has been spilled into the appliance.
B. The appliance has been exposed to rain or water.
C. The appliance does not appear to operate normally or exhibits
a marked change in performance.
American DJ® - www.americandj.com - Inno Roll LED Instruction Manual Page 4
SOUND
Inno Roll LED
Set Up
POWER
DMX+,DMX-,COMMON
cables. Do not use
the ground lug on the XLR connector. Do not connect the cable’s shield conductor to the ground lug or allow the shield
conductor to come in contact with the XLR’s outer casing. Grounding
the shield could cause a short circuit and erratic behavior.
tocol used by most lighting and controller manufactures as a form of
communication between intelligent fixtures and controllers. A DMX
controller sends DMX data instructions from the controller to the fixture. DMX data is sent as serial data that travels from fixture to fixture
via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX
fixtures (most controllers only have a DATA “OUT” terminal).
INPUT
OUTPUT
COMMON
DMX512 OUT
3-PIN XLR
1
2
3
American DJ® - www.americandj.com - Inno Roll LED Instruction Manual Page 5
1
2
DMX +
3
DMX -
3
1
DMX512 IN
3-PIN XLR
2
3
1
2
Figure 2
XLR Female Socket
XLR Male Socket
1 Ground
2 Cold
2 Cold
REMOTE
CONTROL
INPUT
SOUND
INPUT
OUTPUT
1 Ground
XLR Pin Configuration
Pin 1 = Ground
REMOTE
CONTROL
SOUND
3 Hot
INPUT
OUTPUT
INPUT
Pin 2
= Data Compliment (negative)
3 Hot
Pin 3 = Data True (positive)
Figure 3
Special Note: Line Termination. When longer runs of cable are
used, you may need to use a terminator on the last unit to avoid erratic
behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is connected between pins 2 and 3 of a male XLR connector (DATA + and
DATA -). This unit is inserted in the female XLR connector of the last
unit in your daisy chain to terminate the line. Using a cable terminator
(ADJ part number Z-DMX/T) will decrease the possibilities of erratic
behavior.
POWER
Data Cable (DMX Cable) Requirements (For DMX and Master/Slave
Operation): The Inno Roll LED can be controlled via DMX-512 protocol. The Inno Roll LED is a 8 channel DMX unit. The DMX address is
set electronically using the controls on the front panel of the unit. Your
unit and your DMX controller require a approved DMX-512 110COMMON
Ohm
DMX +
DMX512 OUT
Data cable for data input and data output (Figure
3-PIN XLR
DMX 1). We recommend Accu-Cable DMX cables. If you
are making your own cables, be sure to use standard 110-120 Ohm shielded cable (This cable may
be purchased at almost all professional sound and
lighting stores). Your cables should be made with
a male and female XLR connector on either end of
the cable. Also remember that DMX cable must be
Figure 1
POWER
Notice: Be sure to follow
figures two and three when making your own
DMX512
DMX-512: DMX is short for Digital Multiplex. This is a universal pro-
REMOTE
CONTROL
INPUT
Set Up
daisy chained and cannot be split.
voltage switch, which will auto sense the voltage when it is plugged
into a power source. With this switch there is no need to worry about
the correct power voltage, this unit can be plugged in anywhere.
SOUND
SOUN
CONTROL
INPUT
Inno Roll LED
Power Supply: The American DJ® Inno Roll LED contains a automatic
DMX Linking: DMX is a language allowing all makes and models
of different manufactures to be linked together and operate from a
single controller, as long as all fixtures and the controller are DMX
compliant. To ensure proper DMX data transmission, when using
several DMX fixtures try to use the shortest cable path possible. The
order in which fixtures are connected in a DMX line does not influence
the DMX addressing. For example; a fixture assigned a DMX address
of 1 may be placed anywhere in a DMX line, at the beginning, at the
end, or anywhere in the middle. Therefore, the first fixture controlled
by the controller could be the last fixture in the chain. When a fixture
is assigned a DMX address of 1, the DMX controller knows to send
DATA assigned to address 1 to that unit, no matter where it is located
DMX512
in the DMX chain.
DMX+,DMX-,COMMON
SOUND
CONTROL
INPUT
POWER
3
1
2
DMX512 IN
3-PIN XLR
3
1
2
POWER
Termination reduces signal errors and
avoids signal transmission problems
and interference. It is always advisable
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
Figure 4
American DJ® - www.americandj.com - Inno Roll LED Instruction Manual Page 6
Termination
avoids sign
and interfere
to connect a
120 Ohm 1/4
and PIN 3 (
Inno Roll LED
Set Up
Inno Roll LED
System Menu
5-Pin XLR DMX Connectors. Some manufactures use 5-pin DMX-
512 data cables for DATA transmission in place of 3-pin. 5-pin DMX
fixtures may be implemented in a 3-pin DMX line. When inserting standard 5-pin data cables in to a 3-pin line a cable adaptor must be used,
these adaptors are readily available at most electric stores. The chart
below details a proper cable conversion.
3-Pin XLR to 5-Pin XLR Conversion
Conductor
3-Pin XLR Female (Out)
5-Pin XLR Male (In)
Ground/Shield
Pin 1
Pin 1
Data Compliment (- signal)
Pin 2
Pin 2
Data True (+ signal)
Pin 3
Pin 3
Not Used
Pin 4 - Do Not Use
Not Used
Pin 5 - Do Not Use
American DJ® - www.americandj.com - Inno Roll LED Instruction Manual Page 7
American DJ® - www.americandj.com - Inno Roll LED Instruction Manual Page 8
Inno Roll LED
System Menu
Inno Roll LED
System Menu
ADDR - DMX Address Setting.
at any time using the UP or DOWN buttons.
1. Press the MENU button until “ADDR” is displayed, press
ENTER.
SPLC - Split Color mode. With this mode active, color
2. The current address will now be displayed and flashing.
Press the UP or DOWN buttons to find your desired address.
When you have found your desired DMX address press ENTER
then press and hold the MENU button for at least 3 seconds to
set your desired DMX address.
1. Press the MENU button until “SPLC” is displayed, press
ENTER.
SLND - This will let you set unit as a master or slave in a
output will be split and whole. This mode needs to be activated for the split color to work in DMX Mode.
2. The display will show either “YES” or “NO”. Press the UP or
DOWN buttons to select “YES” to activate split color mode, or
“NO” to deactivate split color mode.
master/slave configuration.
3. Press ENTER to confirm.
1. Press the MENU button until “SLND” is displayed, press
ENTER. Either “SL 1” or “SL 2” will be displayed.
DCAL - In this mode you can adjust the LED output inten-
2. Press the UP or DOWN buttons until your desired setting is
displayed, press ENTER to confim.
NOTE: In a Master/Slave configuration you can set one fixture
to Master and then set the next fixture to “SL 2”, the fixtures will
now have contrast movement to each other.
SHND: SH 0 - SH6 - Show modes 0-6 (Factory programs).
sity.
1. Press the MENU button until “DCAL” is displayed, press
ENTER.
2. A number between 50-100 will be displayed. Press the UP
or DOWN buttons to adjust the LED output intensity. 50 being
medium intensity, and 100 being full intensity.
Show mode can run with or without sound active mode.
3. When you have found your desired setting press ENTER to
confirm.
1. Press the MENU button until “SHND” is displayed, press
ENTER.
SOUN - Sound Active mode.
2. “Sh X” will now be displayed, “X” representing a number
between 0-6. Programs 1-6 are factory programs, while “Sh 0”
is random mode. Press the UP or DOWN buttons to find your
desired show.
3. When you have found your desired show press ENTER, then
press and hold the MENU button for at least 3 seconds to activate. After you have set your desired show, it can be changed
American DJ® - www.americandj.com - Inno Roll LED Instruction Manual Page 9
1. Press the MENU button until “SOUN” is displayed, press
ENTER.
2. The display will show either “ON” or “OFF”. Press the UP or
DOWN buttons to select “ON” to activate sound active mode, or
“OFF” to deactivate sound active mode.
3. Press ENTER, then press and hold the MENU button for at
least 3 seconds to activate.
American DJ® - www.americandj.com - Inno Roll LED Instruction Manual Page 10
Inno Roll LED
System Menu
SENS - In this mode you can adjust the sound sensitivity.
1. Press the MENU button until “SENS” is displayed, press
ENTER.
2. A number between 0-100 will be displayed. Press the UP or
DOWN buttons to adjust the sound sensitivity. 0 being the least
sensitive, and 100 being the most sensitive.
3. When you have found your desired setting press ENTER to
confirm.
BLND - Blackout or Stand by mode.
1. Press the MENU button until “BLND” is displayed, press
ENTER. Either Yes or No will be displayed.
2. To activate Blackout tap the UP or DOWN buttons until “Yes”
is displayed, press ENTER to confim. The fixture will now be in
Blackout mode. To deactivate Blackout mode, select “No” and
press Enter.
LED - With this function you can have the LED display
turn off after 10 seconds.
Inno Roll LED
System Menu
DISP - This function will reverse the display 180º.
1. Press the either the MENU button until “DISP” is displayed,
press ENTER.
2. Press the UP button to select “DSIP” to “flip” the display, or
“DISP” to change the display back.
3. Press ENTER to confirm.
PAN - Pan Inversion
1. Press the MENU button until “PAN” is displayed, press
ENTER. Either Yes or No will be displayed.
2. To activate the Pan inversion press the UP or DOWN buttons
until YES is displayed, press ENTER to confim. To deactivate
Pan inversion, select NO and press Enter.
TEST - This function will run a self test program. The test
program will test pan/tilt movement and colors.
1. Press the MENU button until “TEST” is displayed, press
ENTER.
2. The fixture will now run a self test.
1. Press the MENU button until “LED” is displayed, press
ENTER.
TEMP - With this function you can check the temperature
2. The display will show either “ON” or “OFF”. Press the UP or
DOWN buttons to select “ON” to keep the LED display on at
all times, or “OFF” to switch to have the LED display switch off
after 10 seconds.
1. Press the MENU button until “TEMP” is displayed, press
ENTER.
3. Press ENTER to confirm. To make the LED display reappear
after it has turned off, press any button.
of the fixture.
2. The temperature of the fixture will now be displayed. Press
MENU to exit.
FHRS - With this function you can display the running time
of the unit.
American DJ® - www.americandj.com - Inno Roll LED Instruction Manual Page 11
American DJ® - www.americandj.com - Inno Roll LED Instruction Manual Page 12
Inno Roll LED
System Menu
Inno Roll LED
Color & Gobo Adjustment
1. Press the MENU button until “FHRS” is displayed, press
ENTER.
2. The running time of the fixture will now be displayed. Press
MENU to exit.
VER - With this function you can display the version software of the unit.
1. Press the MENU button until “VER” is displayed, press
ENTER.
2. The software version will now be displayed. Press MENU to
exit
PROD - Pro defaults.
1. Press the MENU button until “PROD” is displayed, press
ENTER.
2. The display will show either “YES” or “NO”. Press the UP or
DOWN buttons to select “YES” to reset back to PRO default
settings, or “NO” to not reset to PRO defaults.
3. Press ENTER to confirm.
To enter the Color/Gobo wheel adjustment submenu, press the
ENTER button for at least 5 seconds. In this submenu you are able to
adjust the original position of the gobo wheel and color wheel.
COLO - Adjustment of the color wheel.
1. Press the ENTER button for at least 5 seconds, then press the UP
or DOWN buttons so that “COLO” is displayed, press ENTER.
2. Use the UP and DOWN buttons to make your adjustments, and
then press ENTER to confirm. Press the MENU button for one second
to exit.
GOBO - Adjustment of the gobo wheel.
1. Press the ENTER button for at least 5 seconds, then press the UP
or DOWN buttons so that “GOBO” is displayed, press ENTER.
2. Use the UP and DOWN buttons to make your adjustments, and
then press ENTER to confirm. Press the MENU button for one second
to exit.
RSET - Use this function to reset the unit.
1. Press the MENU button until “RSET” is displayed, press
ENTER.
2. The fixture will now reset,
American DJ® - www.americandj.com - Inno Roll LED Instruction Manual Page 13
American DJ® - www.americandj.com - Inno Roll LED Instruction Manual Page 14
Inno Roll LED
Operation
Operating Modes: The Inno Roll LED can operate in three different modes. In each mode you can run the fixture as a stand
alone fixture or in a master/slave confiugration. This next section will detail the differences in the operating modes.
• Sound Active mode The fixture will react to sound, chasing through the built-in programs.
• Show mode The fixture will run one of six shows that you choose.
• DMX control mode This function will allow you to control each individual fixtures traits
with a standard DMX-512 controller such as the Elation ® Show
Designer.™
Master-Slave Operation This function will allow you to link up to 16
units together and operate without a controller. The units will be sound
activated. In Master-Slave operation one unit will act as the controlling
unit and the others will react to the controlling units programs. Any unit
can act as a Master or as a Slave.
1. Using approved DMX data cables, daisy chain your units togeth- er via the XLR connector on the rear of the units. Remember the Male XLR connector is the input and the Female XLR connector
is the output. The first unit in the chain (master) will use the female XLR connector only - The last unit in the chain will use the male XLR connector only. For longer cable runs we suggest a termina-
tor at the last fixture.
2. On the Master unit find your desired show and set that show by pressiing the ENTER button.
3. On the slave units tap the MENU button until “SLND” is dis-
played, and Press ENTER. Choose either “SL 1” or “SL 2” and press ENTER. See page 9 for more info.
4. The slave units will now follow the Master unit.
Inno Roll LED
2.
3.
4.
5.
6.
7.
To control your fixture in DMX mode, follow the set-up procedures
on pages 5-7 as well as the set-up specifications that are included with your DMX controller.
Use the controller’s faders to control the various DMX fixture traits.
This will allow you to create your own programs.
Follow the instructions on page 9 to set the DMX address.
For longer cable runs (more than a 100 feet) use a terminator on the last fixture.
For help operating in DMX mode consult the manual included with your DMX controller.
Sound Active Mode: This mode allows either single unit or several
units linked together, to run to the beat of the music.
1. Tap the MENU button until “SOUN” is displayed, and press ENTER. Tap the UP or DOWN buttons so that “ON” is dis
played and press ENTER.
2. The optional UC3 Controller (not included) may be used to con-
trol different functions including blackout.
Show Mode: This mode allows either a single unit or several units
linked together, to run one of 6 shows that you choose. Show mode
can run with or without sound active mode.
1. Press the MENU button until “SHND” is displayed, and press ENTER.
2. Press the UP or DOWN buttons until you find your desired show, press ENTER, then press and hold the MENU button for at least 3 seconds to activate. After you have set your desired show, it can be changed at any time using the UP or DOWN buttons.
Inno Roll LED
American DJ® - www.americandj.com - Inno Roll LED Instruction Manual Page 15
UC3 Control
Stand by
Function
Blackout the unit
1. Strobe in synchronization
2. strobe in desynchronization
3. Strobe by music
Select Movement
1-6
Mode
Sound
(LED OFF)
Movement
(LED Blinking)
Universal DMX Control: This function allows you to use a Elation®
universal DMX-512 controller to control the chases and patterns,
dimmer and strobe. A DMX controller allows you to create unique
programs tailored to your individual needs.
1. The Inno Roll LED is an eight DMX channel DMX fixture. See pages 16-18 for detailed description of the DMX values and traits.
Operation
Color/Gobo selection
1. Press shortly for
color change.
2. Hold on for
Gobo change
Gobo/Color
(LED ON)
American DJ® - www.americandj.com - Inno Roll LED Instruction Manual Page 16
Inno Roll LED
Channel
1
2
3
4
Value
0 - 255
0-9
10 - 120
121 - 134
135 - 245
246 - 255
0-7
8 - 15
16 - 131
132 - 139
140 - 181
182 - 189
190 - 231
232 - 239
240 - 247
248 - 255
0 - 14
15 - 21
22 - 28
29 - 35
36 - 42
43 - 49
50 - 56
57 - 63
64 - 70
71 - 77
78 - 84
85 - 91
92 - 98
99 - 105
106 - 112
113 - 119
120 - 127
8 Channel Mode
Inno Roll LED
Function
PAN 0° - 180°
TILT
STOP
CLOCKWISE ROLL FAST - SLOW
STOP
COUNTER CLOCKWISE ROLL
SLOW - FAST
STOP
STROBE
BLACKOUT
OPEN
STROBING SLOW - FAST
OPEN
FAST OPEN - SLOW CLOSE
OPEN
FAST CLOSE - SLOW OPEN
OPEN
RANDOM STROBE
OPEN
COLOR WHEEL
WHITE
WHITE/RED
RED
RED/ORANGE
ORANGE
ORANGE/YELLOW
YELLOW
YELLOW/GREEN
GREEN
GREEN/CYAN
CYAN
CYAN/MAGENTA
MAGENTA
MAGENTA/LIGHT BLUE
LIGHT BLUE
LIGHT BLUE/PURPLE
PURPLE
American DJ® - www.americandj.com - Inno Roll LED Instruction Manual Page 17
Channel
4
5
6
7
8
Value
128 - 191
192 - 255
0-9
10 - 18
19 - 27
28 - 36
37 - 45
46 - 54
55 - 63
64 - 74
75 - 85
86 - 95
96 - 106
107 - 116
117 - 127
128 - 189
190 - 193
194 - 255
0 - 127
128 - 189
190 - 193
194 - 255
0 - 255
0 - 69
70 - 79
80 - 89
90 - 99
100 - 109
110 - 119
120 - 129
8 Channel Mode
Function
COLOR WHEEL CONT.
CLOCKWISE ROTATION FAST - SLOW
COUNTER-CLOCKWISE ROTATION
SLOW - FAST
GOBO WHEEL
OPEN
GOBO 1
GOBO 2
GOBO 3
GOBO 4
GOBO 5
GOBO 6
GOBO 1 SHAKE
GOBO 2 SHAKE
GOBO 3 SHAKE
GOBO 4 SHAKIE
GOBO 5 SHAKE
GOBO 6 SHAKE
CLOCKWISE ROTATION FAST - SLOW
STOP
COUNTER-CLOCKWISE ROTATION
SLOW - FAST
GOBO ROTATION
GOBO INDEXING
CLOCKWISE ROTATION FAST - SLOW
STOP
COUNTER-CLOCKWISE ROTATION
SLOW - FAST
DIMMER 0% - 100%
RESET/BLACKOUT
NO FUNCTION
ENABLE BLACKOUT WHILE PAN/TILT MOVE DISABLE BLACKOUT WHILE PAN/TILT MOVE
ENABLE BLACKOUT WHILE COLOR CHANGE
DISABLE BLACKOUT WHILE COLOR CHANGE
ENABLE BLACKOUT WHILE GOBO CHANGE DISABLE BLACKOUT WHILE GOB CHANGE
American DJ® - www.americandj.com - Inno Roll LED Instruction Manual Page 18
Inno Roll LED
Channel
8
Value
130 - 199
200 - 209
210 - 239
240 - 255
8 Channel Mode
Function
RESET/BLACKOUT
NO FUNCTION
RESET ALL
NO FUNCTION
SOUND ACTIVE
To access the split colors, split color mode must be activated in
the system menu. Please see page 10.
Inno Roll LED
Gobo Replacement
This unit comes with interchangable gobos. When changing
the gobos please be very careful. Follow the instructions below,
and see the figure pictures on the next page.
Caution! Never open the unit when in use. Always disconnect
the main power before attempting to change the gobos.
1. Start by standing the fixture upright so that it is sitting on the bottom handles. Unscrew the two phillips screws located on the front panel just underneath the air vents.
2. Carefully remove the front panel to access the gobo wheel.
3. Rotate the gobo wheel with your hand until you find the gobo you would like to change.
4. Using a pair of needle nose pliers, grab the retainer ring that holds the gobo in place and remove the ring. You can also
remove the gobo by carefully pushing the gobo from the bot-
tom, pushing it up and out. Do this carefully so that you don’t lose the retainer ring and the gobo.
5. Once you have removed the gobo carefully insert your new gobo and reinsert the retainer ring.
6. Reassemble the unit.
American DJ® - www.americandj.com - Inno Roll LED Instruction Manual Page 19
American DJ® - www.americandj.com - Inno Roll LED Instruction Manual Page 20
Inno Roll LED
Fuse Replacement
Locate and remove the unit’s power cord. Once the cord has been
removed located the fuse holder located inside the power socket.
Insert a flat-head screw driver into the power socket and gently pry
out the fuse holder. Remove the bad fuse and replace with a new one.
The fuse holder has a built-in socket for a spare fuse be sure not to
confuse the spare fuse with active fuse.
Inno Roll LED
Cleaning
Fixture Cleaning: Due to fog residue, smoke, and dust cleaning
the internal and external optical lenses and mirror should be carried
out periodically to optimize light output. Cleaning frequency depends
on the environment in which the fixture operates (I.e. smoke, fog
residue, dust, dew). In heavy club use we recommend cleaning on a
monthly basis. Periodic cleaning will ensure longevity, and crisp output.
1. Use normal glass cleaner and a soft cloth to wipe down the out-
side casing.
2. Use a brush to wipe down the cooling vents and fan grill.
3. Clean the external optics with glass cleaner and a soft cloth every 20 days.
4. Clean the internal optics with glass cleaner and a soft cloth every 30-60 days.
5. Always be sure to dry all parts completely before plugging the unit back in.
Inno Roll LED
Trouble Shooting
Trouble Shooting: Listed below are a few common problems that
you may encounter, with solutions.
No light output from the unit;
1. Be sure the external fuse has not blown. The fuse is located on the bottom panel of the unit.
2.Be sure the fuse holder is completely and properly seated.
Unit does not respond to sound;
1. Low frequencies (bass) should cause the unit to react to sound.
Tapping on the microphone, quiet or high pitched sounds may
not activate the unit.
American DJ® - www.americandj.com - Inno Roll LED Instruction Manual Page 21
Inno Roll LED
Warranty
MANUFACTURER’S LIMITED WARRANTY
A. American DJ, Inc. hereby warrants, to the original purchaser, American DJ and American
Audio products to be free of manufacturing defects in material and workmanship for a prescribed
period from the date of purchase (see specific warranty period on reverse). This warranty shall be
valid only if the product is purchased within the United States of America, including possessions
and territories. It is the owner’s responsibility to establish the date and place of purchase by acceptable evidence, at the time service is sought.
B.
For warranty service you must obtain a Return Authorization number (RA#) before
sending back the product. Contact American DJ, Inc. Service Department at 800-322-6337. Send
the product only to the American DJ, Inc. factory. All shipping charges must be pre-paid. If the
requested repairs or service (including parts replacement) are within the terms of this warranty,
American DJ, Inc. will pay return shipping charges only to a designated point within the United
States. If the entire instrument is sent, it must be shipped in it’s original package. No accessories
should be shipped with the product. If any accessories are shipped with the product, American DJ,
Inc. shall have no liability whatsoever for loss of or damage to any such accessories, nor for the
safe return thereof.
C. This warranty is void if the serial number has been altered or removed; if the product is
modified in any manner which American DJ, Inc. concludes, after inspection, affects the reliability
of the product; if the product has been repaired or serviced by anyone other than the American DJ,
Inc. factory unless prior written authorization was issued to purchaser by American DJ, Inc.; if the
product is damaged because not properly maintained as set forth in the instruction manual.
D.
This is not a service contract, and this warranty does not include maintenance, cleaning
or periodic check-up. During the period specified above, American DJ, Inc. will replace defective parts at its expense with new or refurbished parts, and will absorb all expenses for warranty
service and repair labor by reason of defects in material or workmanship. The sole responsibility
of American DJ, Inc. under this warranty shall be limited to the repair of the product, or replacement thereof, including parts, at the sole discretion of American DJ. All products covered by this
warranty were manufactured after January 1, 1990, and bear identifying marks to that effect.
E.
American DJ, Inc. reserves the right to make changes in design and/or improvements
upon its products without any obligation to include these changes in any products theretofore
manufactured. No warranty, whether expressed or implied, is given or made with respect to any
accessory supplied with products described above. Except to the extent prohibited by applicable
law, all implied warranties made by American DJ, Inc. in connection with this product, including
warranties of merchantability or fitness, are limited in duration to the warranty period set forth
above. And no warranties, whether expressed or implied, including warranties of merchantability
or fitness, shall apply to this product after said period has expired. The consumer’s and/or Dealer’s
sole remedy shall be such repair or replacement as is expressly provided above; and under no
circumstances shall American DJ, Inc. be liable for any loss or damage, direct or consequential,
arising out of the use of, or inability to use, this product. This warranty is the only written warranty applicable to American DJ and American Audio Products and supersedes all prior warranties and written descriptions of warranty terms and
conditions heretofore published.
MANUFACTURER’S LIMITED WARRANTY PERIODS:
• All American Audio Products = 1-year (365 day) Limited Warranty (except V-Plus Series Amplifiers)
• All American Audio V-Plus Series Amplifiers = 3-year (1095 day) Limited Warranty
• American DJ Lighting and American DJ Branded Products = 1-year (365 day) Limited Warranty
(Such as: Special Effect Lighting, Intelligent Lighting, UV lighting, Strobes, Fog Machines, Bubble
Machines, Mirror Balls, Par Cans, Trussing, Lighting Stands etc. excluding Laser Products, lamps,
and Star Tec Series)
• American DJ Laser Products and Star Tec Products = 90-Day Limited Warranty
• American DJ L.E.D. Products = 3-year (1095 day) Limited Warranty (excluding motors, PCB
boards, and power supplies, which have a 1-year (365 day Limited Warranty).
American DJ® - www.americandj.com - Inno Roll LED Instruction Manual Page 22
Inno Roll LED
Model: Specifications
Inno Roll LED
Voltage:
100V ~ 240V/50~60Hz
LED:1 x 50W LED
Power Consumption:
103W
Dimensions: 11”(L) x 8.25”(W) x 22”(H)
274mm x 208mm x 555mm
Beam Angle:
40 Degree
Weight:
14 Lbs. / 6.3 kgs.
Fuse:2 Amp
Duty Cycle:
None
DMX: 8 Channels
Colors:8 + White
Gobos:23.8mm (Size)
19mm (Viewable
Sound Active:Yes
Working Position:
Any Safe, Secure Position
Warranty:
3 Year (1095 days)
Auto Sensing Voltage: This fixture contains a automatic voltage switch, which will auto sense the voltage when it is plugged
into the power source.
Please Note: Specifications and improvements in the design
of this unit and this manual are subject to change without any
prior written notice.
American DJ® - www.americandj.com - Inno Roll LED Instruction Manual Page 23
©American DJ Supply
American DJ World Headquarters:
6122 S. Eastern Ave. Los Angeles, CA 90040 USA
Tel: 323-582-2650 / Fax: 323-725-6100
Web: www.americandj.com / E-mail: info@americandj.com
American DJ Europe
Junostraat 2
6468 EW Kerkrade
Netherlands
service@adjgroup.eu / www.americandj.eu
Tel: +31 45 546 85 00 / Fax: +31 45 546 85 99