Shinepal Electronics SP711 Instruction manual

Shinepal Electronics Co., Ltd
www.shinepal.com
GSM Multi-media Message Alarm
SP711
Operation Manual
Shinepal Electronics Manufacturing Co., Ltd
Factory address: FuYuan Industrial City, XiXiang BaoAn District ShenZhen City China 518126
Michael Yang
Sales Manager
Website: www.shinepal.com
Call: (86-755) 27809392
Fax: (86-755) 27809392
Web: www.Shinepal.com
MSN: shinepal@live.cn
Email: shinepal2008@gmail.com
Skype: shinepal
Google Talk: shinepal2008
Real time Audio and Video, Wireless monitor and control
Shinepal Electronics Co., Ltd
www.shinepal.com
Contents
Quick Programming ..................................................................... 2
1. General Information................................................................. 4
1-1 Introduction ....................................................................... 4
1-2 Features ............................................................................ 5
1-3 About the Console............................................................... 5
1-4 Package List....................................................................... 6
1-5 Major Technical Parameters .................................................. 6
2. Operation................................................................................. 7
2-1 Major Function ................................................................ 7
2-1-1 Active reviewing function ............................................ 7
2-1-2 Infrared Heat & Motion Dual-Tech Detection................... 7
2-1-3 Emergency call key .................................................... 7
2-1-4 Listen in ................................................................... 7
2-2 Commands ...................................................................... 8
2-2-1 N: To Program Password ............................................. 9
2-2-2 M: To Program Receiver’s Phone Number ...................... 9
2-2-3 E: To Program Email Address....................................... 9
2-2-4 S: To Siren ON/OFF Switch.......................................... 9
2-2-5 H: To Program Emergency Alarm ................................. 9
2-2-6 A: To Activate/Release the System ............................. 10
2-2-7 D: To Check System Settings .................................... 10
2-2-8 T: To Listen in ......................................................... 10
2-2-9 1—7Supervise the Site ............................................. 10
2-2-10 C: To Reset the System .......................................... 10
2-2-11 U: SMS extension unit alarming ............................... 11
2-2-12 J1/J0 320X240/480 X320 pixels ................................ 11
2-3 Remote Control Unit ...................................................... 11
2-3-1 Buttons .................................................................. 11
2-3-2 Enrollment.............................................................. 12
2-4 Extension unit operations .............................................. 12
3. Notes ..................................................................................... 13
3-1 Location for the System ..................................................... 13
3-2 Data Transmission and MMS Activation................................. 13
3-3 Notes for Console’s SIM ..................................................... 13
3-4 Solution for Password Forgotten .......................................... 13
3-5 FAQ ................................................................................ 13
3-6 Installation Location .......................................................... 14
3-7 About Heat Detection ........................................................ 15
3-8 About Motion Detection...................................................... 15
3-9 MMS Acess Method For SP711............................................. 15
Quick Programming
Installation
Shinepal Electronics Co., Ltd
www.shinepal.com
1. Insert SIM card, which MMS is activated, without PIN code
SIM Card Holder
2. Select location where signal strength is strong for communication, mounts the console, and adjust camera lens to
proper position.
3. Plug in power, +6V, and turn on. Console sounds a beep and 3 beeps around 15 seconds later to indicate system
is ready. If 3 beeps not heard, remove the power, check, re-insert the SIM, and re-power after 3 minutes.
4. Follow the examples to program system in flash.
Key in: “000000 M#0932345678,0935111111,0930333333 Egsm.car.alarm@hotmail.com“Send this
short message to console phone number
Confirmation: administrator will receive a SMS for confirmation as
“M: #0932345678,0935111111,0930333333 Egsm.car.alarm@hotmail.com“to indicate programming is
successful. #0932345678 represents this is the administrator phone number. , 09351111111 and 0930333333
are general user. (Note: Administrator does not need password to program and operate the system; password is
necessary for other user(s) to perform the work. (Refer to Section 2-2-2 for details.)
Commands
1. You must well know the commands in the table to operate the system
Command
N
E
Function
Command
Program
M
password
Program receiver
S
email address
Program
H
A
emergency
alarm receiver
D
Check System
Settings
Function
Program receiver phone
number(s)
1: enable strobe
0: disable strobe
1: Activate
0: Release
T
Listen-in
C
Default settings
Ext.unit
U
alarming(reserved
func.)
1-7
Supervise the Site
J1/J0
320X240/480X320pixels
SMS format: (Password)+Command1+Setting1+Command2+Setting2+……
2. Setting example:
N: To Program Password (console default password 000000)
Send“000000N111111”SMS to console phone number
Confirmation: user will receive a SMS for confirmation as N: 111111
M: To Program Receiver’s Phone Number
Send“000000M#0932345678,0935111111”SMS to console phone number
Shinepal Electronics Co., Ltd
www.shinepal.com
Confirmation: user will receive a SMS for confirmation as “M:#0932345678,
0935111111” to indicate programming is successful.
Send“000000M” SMS to console phone number
Confirmation: user will receive a SMS for confirmation as M-deleted
E: To Program Email Address
Send“000000Ejuly@yahoo.com,gsm.car.alarm@hotmail.com”SMS to console phone number
Confirmation: user will receive a SMS for confirmation as
“E:car_alarm@yahoo.com,
gsm.car.alarm@hotmail.com” to indicate programming is successful.
Send“000000E” SMS to console phone number
user will receive a SMS for confirmation as E-deleted
A: To Activate/Release the System
Send“000000A1” SMS to console phone number
Confirmation: user will receive a SMS for confirmation as “detector on” to indicate
programming is successful.
Send“000000A0” SMS to console phone number
Confirmation: user will receive a SMS for confirmation as “detector off”
S: To Siren ON/OFF switch
Send“000000S1” SMS to console phone number
Confirmation: user will receive a SMS for confirmation as “sound open” to indicate programming is successful.
Send“000000S0” SMS to console phone number
Confirmation: user will receive a SMS for confirmation as “sound close”
1-7 Supervise the Site
Send“0000002” SMS to console phone number
Confirmation: console send two pictures to caller and the first email address programmed to indicate programming
is successful.
D: To Check System Settings
Send“000000D” SMS to console phone number
Confirmation: user will receive a SMS for confirmation as Ver: YJ5.3 sound open detector on jpg:320*240 N:
111111 M:#0932345678, 0935111111
E: gps_alarm@yahoo.com, gsm.car.alarm@hotmail.com H : 110, 0938666666
T: To Listen in
Send“000000T” SMS to console phone number
In 1 minute, system will call the phone number received for the user to listen in the premise.
1. General Information
1-1 Introduction
SP711 Mobile(AV)monitor is a brand new Hi-Tech product in the wireless communication era, it has integrated
2G & 3G mobile transmission technology and IR image monitoring and thermo detection such kinds of security
technologies.
It has breaking thru the limitation of conventional CCTV system that transmitting by hardwire cable/modem
which is difficult to install and has higher cost and limited by the installation environment, it also has problem of easy
to be invaded.
This product combines the future mobile user’s needs to let any mobile phone user (must have GPRS/MMS/SMS
Shinepal Electronics Co., Ltd
www.shinepal.com
function) can use their mobile’s AV and mailbox function to back up the image information (to avoid the destroy of
evidences), can real-time receives the alarm messages from any remote location by the AV Monitor devices or
monitoring the real-time voice and image from the site for immediate identification. It meets various demands from
sectors of household, office, factory, stores….etc.
1-2 Features
z
IR thermo image monitoring and detection for moving objects, the double detection technology can eliminate
z
It has real-time mobile AV alarm and e-mail video image back-up receiving model.
z
You can monitor the site by mobile phone at any time.
z
You can use mobile to monitor the voice at the remote site.
z
Alarms will activate the pre-recorded voice messages and inform the users immediately.
z
Easy operate with a wireless remote control device by simple mobile instructions.
z
You can setting if the siren and beacon device to be activated when alarm happen.
z
Under emergency situation EMSD key can silently inform any designated users.
z
With build-in back up battery, device can be still operating during power failure.
z
With IR night vision camera, it provides full time 24 hours day and night monitoring function.
the false alarm caused by environmental reasons.
1-3 About the Console
Antenna
IR Camera
Battery cover
Thermo
Detector
Flash
Speaker
Mounting buckle
Shinepal Electronics Co., Ltd
www.shinepal.com
Microphone
Video output
Power switch
Serial port
Power socket
1-4 Package List
1)Standard accessories:
a) Consol x 1
e) Antenna x 1
b) Power adaptor x 1
f) Remote Con.
X2
c) Rechargeable battery x 1
g) Instruction Manual x 1
d) Universal mounting kit x 1
h) Warranty card x 1
2)Options:
a) Enhanced antenna
b) Remote con.(maximum number is 10 units)
c) Alarm extension unit(Camera unit or Detection unit)
Reserved function (future version)
d) Video line (digital signal serial port)
Reserved function (future version)
1-5 Major Technical Parameters
PIC Format
JPEG
Resolution
320X240 /480 X320 pixels
Camera View Angle
Horizontal 60º / Vertical 60º
Effective Range
< 20 meters
Remote Control Distance < 30 meters
Backup Battery
< 24 hrs (depends on battery capacity)
Working Temperature
0-50ºC (32-122ºF)
Relative Humidity
10-90%, non-condense
Shinepal Electronics Co., Ltd
www.shinepal.com
2.
Operation
2-1 Major Function
2-1-1 Active reviewing function
User can supervise the site by calling the console or sending SMS to console. Instructions are as follows.
A. By Calling
Make sure the feature of MMS is activated for both caller and the console. You just call the console phone number, and
console will pick up, confirm, and hang up the call. After taking a picture of the premise, console will send the picture
to the caller and the first email address if any email address has been programmed. If system authority level has
been programmed as administrator and other user(s), only the administrator can perform this feature by calling and
sending SMS plus password for other user(s).
B. By Sending SMS
Format: 0X
Where
0 (zero): command for sending picture of premise
X: quantity of picture required to review from 1 to 9
Ex: Send“00000002” SMS to console phone number
000000 is default password, the 7th show Console, Console will process SMS received, take two pictures, and then
send to caller and email address programmed.
Note:
1. If none phone number is programmed as alert receiver, any mobile phone with feature of MMS activated can
perform this function. Only the administrator and user(s) can do so when receiver phone numbers are
programmed.
2. Caller ID and MMS should be activated, and Voice Box and Call-Waiting should be deactivated for the console.
2-1-2 Infrared Heat & Motion Dual-Tech Detection
Infrared heat & motion is active under system arming mode to detect any motion object in the premise. If any
motion object, i.e. intruder, is detected, system will send 3 pictures to designated receiver(s). There is 3 seconds
of time interval between the first and second shot; the third shot will be sent after the strobe starts to work. After
sending pictures, system calls each receiver and play pre-recorded vocal message if the line is through. 十分钟
内不再触发报报警。
2-1-3 Emergency call key
Under panic or emergency circumstance, such as duress or intrusion, you can press and hold the emergency button
on the remote control unit for 3 seconds to initiate a silent alarm and alert designated emergency alarm receiver, and
system plays 3 cycles of vocal emergency message when the line is through. Meanwhile, all receivers of designated
phone and email address will have picture of premise and vocal emergency alarm alert as well. If line is not through,
system will terminate alerting after 5 attempts of calling in 3 minutes of time interval. Refer to Section 2-2-5 for
details of programming emergency alarm receiver and Section2-3-1 for remote control unit operation.
2-1-4 Listen in
You just need to send the SMS to the console, and you will receive call back for the receiver to listen in the sound of
premise. You can send SMS: "T+ telephone number or mobile phone number," in one minute console will phone the
number behind of the "T". Users receive, they can monitor the voice of the scene. Send SMS: "T", console will call the
mobile phone number which send SMS.
Shinepal Electronics Co., Ltd
www.shinepal.com
2-2 Commands
You must well know the commands in the table to operate the system
Function
Command
N
E
Program
password
Program receiver
email address
Command
M
S
Program
H
emergency
A
alarm receiver
D
Check System
Settings
Function
Program receiver phone
number(s)
1: enable strobe
0: disable strobe
1: Activate
0: Release
T
Listen-in
C
Default settings
Ext.unit
U
alarming(reserved
func.)
1-7
Supervise the Site
J1/J0
320X240/480X320pixels
SMS format: (Password)+Command1+Setting1+Command2+Setting2+……
In each SMS, you can combine commands to perform single or multi programming. Beware of that previous setting
will be overlapped and invalid by new setting automatically.
Cautions:
①perform programming: If administrator and user(s) are assigned, password is not required for administrator
and necessary for other user(s).
②SMS should be keyed either in English or Chinese. Maximal up to 140 characters for English and 70 characters
for Chinese compose the SMS command list, which includes characters, numbers, and symbols.
③While programming email address, only lowercase is decodable for email address entry.
④Other than “ , “ (comma) is used as a separator in a command list, “ “(space) and “ * “ (asterisk) can be used
as separators as well.
⑤Password is composed of 6 digit numbers, 0-9.
⑥Maximal up to 5 receiver phone numbers, 3 email addresses, and 5 panic alarm receivers can be programmed
respectively.
⑦Even though separator is not a must during two different commands, we strongly recommend to use separator
between the commands. In contrast, separator is mandatory for the setting, such as phone number, after the
command if setting is more than one.
⑧While programming email address, only English letter, number, and underscore are acceptable. Semicolon, “ ; ”,
is used as prefix and suffix of command list for email address programming. Comma, “ , ”, is used to divide
every email address if email address for programming is more than one and used to close email address entry.
Max. up to 3 email addresses can be stored into system; newly programmed email address will clear and
overlap previous email address settings automatically. Format is shown as follows.
Eemail,email,email,;
⑨If you program phone set, not mobile phone, as receiver, the system will just send vocal alert message instead
of the pictures of premise when alarm occurs.
Refer to the following examples for detailed instruction for programming.
(System Default Password: 000000)
Shinepal Electronics Co., Ltd
www.shinepal.com
2-2-1 N: To Program Password
z To change default password 000000 to preferable code, 111111
Send“000000N111111”SMS to console phone number
Confirmation: user will receive a SMS for confirmation as N: 111111
Password is not necessary if operate or program the system from administrator’s mobile phone; it is mandatory for
other programmed users. Password is located at the front of any command list if programmed user is intending to
operate or program the system.
2-2-2 M: To Program Receiver’s Phone Number
To program administrator phone number, 0932345678, and user phone number, 0935111111, as receivers.
z
Send “000000M#0932345678, 0935111111 “SMS to console phone number
Confirmation: user will receive a SMS for confirmation as M #0932345678, 0935111111 to indicate
programming is successful.
To delete all programmed phone number(s)
z
Send”000000M “SMS to console phone number
Confirmation: user will receive a SMS for confirmation as M-deleted
If none phone number is programmed as alert receiver, any mobile phone with feature of MMS activated can perform
site supervision, listening in,..etc.
2-2-3 E: To Program Email Address
Email address programming should be performed individually not allowed to combine
with other command in a single SMS.
z
To program alert path to designated email address, july@yahoo.com & gsm.car.alarm@hotmail.com from a
user mobile phone.
Send:”000000Ejuly@yahoo.com,gsm.car.alarm@hotmail.com” SMS to console phone number
Confirmation: administrator will receive a SMS for confirmation as
E:july@yahoo.com,gsm.car.alarm@hotmail.com to indicate programming is successful.
z
To Delete Programmed Email Address from user’s mobile phone
Send: “000000E”SMS to console phone number
Confirmation: administrator will receive a SMS for confirmation as
E-deleted to indicate programming is successful.
2-2-4 S: To Siren ON/OFF Switch
z
To activate siren and beacon
Send: “000000S1” SMS to console phone number
Confirmation: user will receive a SMS for confirmation as sound open to indicate programming is
successful.
z
To Delete siren and beacon
Send: 000000S0 SMS to console phone number
Confirmation: user will receive a SMS for confirmation as sound close to indicate programming is
successful.
2-2-5 H: To Program Emergency Alarm Receiver Phone Number(s)
z
To program police station (119) and 0938666666 as emergency alarm receivers,
Send: “000000H119, 0938666666” SMS to console phone number
Confirmation: user will receive a SMS for confirmation as H: 119, 0938666666 to indicate programming is
successful.
Emergency alarm alert would be active only when the receiver(s) is designated.
Shinepal Electronics Co., Ltd
www.shinepal.com
z
To deactivate or delete the panic alarm receiver(s),
Send:”000000H” SMS to console phone number
Confirmation: user will receive a SMS for confirmation as H-Deleted to indicate programming is successful.
Note:
a.119 is local emergency line and should be authorized by related department, such as police station, before
programmed.
b. Strongly recommend not to program receivers who live within same premise. Thus, intruder would know
that owner has initiated emergency call when user’s phone rings.
Note: When setting the emergency call as 110, please be careful to use emergency call, must prevent false
alarm and has to get approval of local police , you can have 5 emergency call numbers, it will be dialed sequencially
follow the setting you made until the phone number you set has been pick up or hang up, or it will re-dail for 10
cycles. Emergency call number is not proper to set user’s own mobile number to avoid reminding the criminals at
the site, it’s better set as 110 or your relative not at the site.
2-2-6 A: To Activate/Release the System
You can Activate/Release the system by sending SMS or using remote control unit when you are leaving the
premise. Arming or disarming is to activate or deactivate the built-in heat & motion detector. Refer to Section 2-3-1
for the remote control unit Operation.
z
Activate the system
Send: “000000A1” SMS to console phone number
Confirmation: administrator will receive a SMS for confirmation as detector on
If any moving object, i.e. intruder, is detected, system will process alarm alert as programmed.
z
Release the system
Send: “000000A0” SMS to console phone number
Confirmation: administrator will receive a SMS for confirmation as detector off
System will not process any alarm alert If any motion is detected
2-2-7 D: To Check System Settings
z
You may check and review system present settings at any time
Send: “000000D” SMS to console phone number
Feedback example as follows:
Ver: YJ5.3 sound open, detector on, jpg:320*240 N:111111
M:#0932345678, 0935111111
E: gps_alarm@yahoo.com, gsm.car.alarm@hotmail.com
110, 0938666666
2-2-8 T: To Listen in
Sender can assigned any phone set or mobile phone number followed command T.
z
User with phone number 0923999999 intends to listen in the premise,
Send: “000000T0923999999” SMS to console phone number
In 1 minute, system will call the phone number received for the user to listen in the premise.
2-2-9 1—7Supervise the Site
Send“00000002” SMS to console phone number
000000 is default password, take two pictures, and then send to caller and email address programmed.
2-2-10 C: To Reset the System
z
To clear all present system setting and revert to factory default,
Send: “000000C”SMS to console phone number
H:
Shinepal Electronics Co., Ltd
www.shinepal.com
Confirmation: administrator will receive a SMS for confirmation as:factory reset
After resetting the system, system should be restarted and all the remote units should be registered to the system
again before using.
Try not to use this setting together with other setting operations, better do it independently.
2-2-11 U: SMS extension unit alarming (reserved function for future version)
z
If you use the monitor extension units, #1for the room, #2 for the warehouse, operate as follows:
Send “000000U1Room Alarm, 2warehouse alarm” SMS to console phone number
Confirmation: administrator will receive a SMS for confirmation as “u:1room alarm ,2warehouse alarm” to indicate
programming is successful.
z
delete the alarm contents
Send “000000U” SMS to console phone number
Confirmation: administrator will receive a SMS for confirmation as “U—deleted”
Note:One master unit can max. connected with 8 extension units, Try not to use this setting together
with other setting operations, better do it independently.
2-2-12 J1/J0 320X240/480 X320 pixels
Console default pixels is 320X240
Send “000000J0” SMS to console phone number
Confirmation: administrator will receive a SMS for confirmation as “pixels 320X240”
to indicate programming is successful.
2-3 Remote Control Unit
2-3-1 Buttons
1. Activation
3. Testing
2. Release
4. Emergency call
Button 1: Activation
You should operate the remote control unit within 100 meters, transmission range, to activation the system.
Once the button pressed, the console will sound continuous high-low beeps, and system enter armed mode
after 1 minute.
Button 2: Release
You should operate the remote control unit within 100 meters, transmission range, to release the system. Once
the button pressed, the console will sound a long beep, and system enter disarmed mode.
Button 3: Testing
You should operate the remote control unit within 100 meters, transmission range, to release the system. Once
the button pressed, the console will sound beep a twice, and system enter disarmed mode. If press and hold
the button for 3 seconds, system will enter or exit factory testing mode. Testing is only for factory inspection
purpose, not for end user.
Button 4: Emergency Call
Shinepal Electronics Co., Ltd
www.shinepal.com
Within transmission range, press and hold the button for 3 seconds to initiate
emergency alert. If it is answered the monitor unit will broadcast the pre-record
voice to give the warning messages.
2-3-2 Enrollment
If you are not able to operate the remote control unit(s) normally after system resetting or adding new one(s),
you need to re-enroll the remote control unit (s) to system. Instruction is shown as follows.
● Power the system, turn on power switch, and wait for system initialization
completed (3 long beeps heard).
● After system initialization, use a conductive object, i.e. screw driver, to short 2 pins, located
as sign pointed
and circled at the drawing below, and remove the object immediately after a short beep is heard. Within 15
seconds, press any button continuously to register the remote control unit to system. You may stop pressing the
button when a long beep is heard to indicate the remote control unit registration successful.
Interface configuration
● Follow the steps above to register all the remote control units up to 10 to system.
● If any remote control units is lost, you may delete all registered remote control units, instruction as below and
follow the steps above to re-register the rest remote control units to system again.
1. Use a conductive object, i.e. screw driver, to short 2 pins, located as
sign pointed and circled at the drawing
above,
2. Remove the object immediately after a long beep is heard.
3. Follow the remote control unit registration procedure to re-enroll them to system.
● System should be rebooted after all remote control units are registered.
2-4 Extension unit operations (Reserved function for future version)
While you have the console, you still can install the extension units within the effective distance, extension units
has SMS unit and Video unit two different types:
SMS unit is to give alarm massages thru SMS(see2-2-11 U— SMS alarm settings)
For example : #2 extension alarm has been triggered you can receive the messages on your mobile with
following SMS:
“No.2 give alarm”
Video extension is giving image alarm messages.
Extension units must do the channel matching with the console before use, it’s similar with the way we did for the
remote control unit:
Put the two pins under the
mark under the console make them short circuit (one touch each other) and
released, you will get a beep sound from the console, then switch ON the power of extension unit in 15 sec. It
response, when you get a long beep from the console means the channel matching is success.
The installation environment of extension unit is the same as the master unit, but the distance between master
and extension unit can’t not over 80 meters (80 meters without any thing blocked) radio wave will be affected by the
environment and the distance.
Shinepal Electronics Co., Ltd
www.shinepal.com
3. Notes
3-1 Location for the System
⑴ Selecting proper location for system installation, you should check the GSM/GRRS signal before installing. You
may use your mobile phone with signal strength indicator to check if signal strength of location is strong or not.
⑵ Electricity power, AC110/220V, should be easy to access.
⑶ System is designed for indoor application, not for outdoor.
⑷ Location should keep away from air-conditioner outtake, steamy area, heat zone, and electromagnetic area.
⑸ System should avoid facing the direct sunlight or being blocked by other object.
⑹ System should avoid facing the area and passage of pets and sun light.
⑺ System should avoid facing transparent window directly.
3-2 Data Transmission and MMS Activation(Refer to last section 3-9)
Users’ mobile phones should feature GPRS MMS and SMS, and CSD digital data transmission is activated. In
addition, the phone set should be programmed properly for GPRS/MMS/SMS operation.
Due to difference of telecommunication service providers and mobile phone models, please consult with service
provider for programming.
3-3 Notes for Console’s SIM
1). If site supervision is frequently used, please select the higher packet rate of telecommunication service. If
not frequently use, basic rate will be enough to cover.
2). For saving on telecommunication, disable the feature of Caller ID of console. If so, only SMS can operate and
program the system.
3). Before inserting the SIM to the console, unnecessary features, i.e. voice box and call waiting, should be
disabled at a mobile phone. Insert the SIM to any mobile phone and contact service for correct procedures.
4). Refer to user instruction of mobile phone to disable the PIN for the SIM.
3-4 Solution for Password Forgotten
If the password is forgotten or missing, you may follow the steps to reset the password.
1). Press and hold the Disarm/Test button on any registered the remote control unit for 3 seconds; a long beep
is heard to indicate system is entering test mode.
2). Short the pins at the connector shown as the following drawing with a conductive object, such as a screw
driver; a long beep is heard again to indicate the password has been reset and reverted to default password,
000000.
3). Press and hold the Disarm/Test button on any registered the remote control unit for 3 seconds; a long beep
is heard to indicate system is back to standby mode.
4). Reboot the system for operation or programming.
Caution: Don’t short other pins on the connector and touch other metallic object during resetting.
3-5 FAQ
Q1. System doesn’t initialize after rebooting.
A1: Switch off the power, remove the power cord, the backup battery, and check if SIM is inserted properly.
Re-power the system after 3 minutes.
Shinepal Electronics Co., Ltd
www.shinepal.com
Q2. The remote control unit doesn’t work.
A2: Check if battery or the remote control unit fails. If not, reboot the system to solve the question. If problem still
exist, re-enroll the remote control unit to the system.
Q3. System is not working
A3: Check if system is in testing mode, the bill of console telecommunication paid, or PIN for the SIM card does not
disabled. If none of above condition, reboot the system. If junk SMS has occupied the memory of system, you
clear the memory by rebooting the system.
3-6 Installation Location
Mobile Monitor 18 is for indoor application. Detection range, sensitivity, and false alarm are decided by the
installation location. The following are strongly recommend for selecting location and installing the system.
1). Sensitivity of heat detection is decided by the direction of the moving object. If the object is moving towards
to the lens of the console, sensitivity of heat detection will be less accurate than moving cross the zone.
Shown as Fig-1
Fig-1
2). System should face potential cross passage of moving object.
3). Recommended height for installation is 2.0~2.2 meters to cover maximal detection area shown as Fig-2.
Fig-2
4). Console should keep away from air-conditioner, refrigerator, heater, gas burner, or some other heat radiation
source, which will affect detection sensitivity and cause false alarm.
5). Console lens should not be blocked by blockades such as shield, plants, or other furniture.
6). Console should avoid facing window directly, which outdoor air flow or other moving object will cause false
alarm. Before arming the system, pull curtain or blind to cover the window for better performance.
7). Console should avoid the location of high density RF, heat radiation, or strong air flow.
Fig-3
Shinepal Electronics Co., Ltd
www.shinepal.com
3-7 About Heat Detection
Fig-4
Face, elbow, and arm have stronger heat radiation than lower potion of human
body. If location is higher than a human height, console should adjust downward to keep zone A of lens in function.
If location is lower than human height, no adjustment is needed.
Fig-5 and Fig-6 indicate how the detection zones distribute and range; they are measured under conditions of
installation at 2 meters high, angle 6° downward, and the moving object is over 1 meter tall with heat radiation.
Fig-5
Fig-6
3-8 About Motion Detection
Motion
detection
technology
is
based on the difference between the
images of
previous and present pictures shot by
the
built-in
infrared
camera.
The
camera and heat detector have the
cone-shape view angle of 60°. Only if the heat and motion detection devices are triggered at the same, and then the
system will process alarm procedure. This advanced technology is to provide higher accuracy and to prevent false
alarm.
3-9 MMS Access Method For SP711
Firstly, make sure that host monitor is in the test mode.
Secondly, send short message to the host monitor as following form to finish the Access Establishment :
Short message form: Password g Homepage(PORT),IP address,APN,( IP Port),(User Name),(Password),
Be careful that: Content in bracket is default number, ,it is ignorable if not have.
The ‘,’can not be ignored.
eg:
The Establish content of short message for New World of HONG KANG:
000000ghttp://mmsc.nwmobility.com:8002,192.168.111.1,mms,9201,,,
The short massage content reference to parameters provided by telecommunic- ation company. The parameters
maybe different in different country and different area,it depend on the telecommunication company corresponding
to the SIM card in SP711.
New World (新世界傳動網)
電訊網絡商:
接入點名稱 Access Point
(APN)
New World (新世界傳動網) 之設定
mms
Shinepal Electronics Co., Ltd
www.shinepal.com
主頁 Homepage
IP 地址
IP address
http://mmsc.nwmobility.com:8002
192.168.111.1
用戶名稱 Login name
密碼 Password
端口號 IP Port
9201
連結方式
持續連結
認證類型
普通
安全保護
關
explain of the short message:
1: “ 000000” is the default password of host monitor;
2: “ g” is command character;
3: “ http://mmsc.nwmobility.com:8002” is the Homepage,some times call the MMSC URL “8002” as the
http port ,when the port is “80”,it can be ignored .
4: “192.168.111.1” is IP address,Gateway IP address.
5: “ mms” is APN ,APN is abbreviate of Access point name
6: If the port is “9201”,it can be ignored, but the’,’ followed can not be ignored.
So the short massage above can also be write as:
000000ghttp://mmsc.nwmobility.com:8002,192.168.111.1,mms,,,,
7: User Name and Password can be ignored if not have, but the’, ’followed
cannot be ignored.