Epson ELPAP03 User`s guide

1
Wireless LAN unit
User's Guide
ELPAP03
Notations Used in This Guide
f General information indications
Attention
q
s
Indicates procedures which may result in damage or injury if sufficient care is not taken.
Indicates additional information and points which may be useful to know regarding a topic.
Indicates a page where detailed information regarding a topic can be found.
Procedure
Indicates operating methods and the order of operations.
The procedure indicated should be carried out in the order of the numbered steps.
[ (Name) ]
Indicates the name of the buttons on the remote control or the control panel.
Example: [Esc] button
"(Menu Name)"
Indicates configuration menu items.
Example: "Image" - "Brightness"
2
Supplied Items List
See the following check list to make sure that you have all of the
supplied items. If anything is missing or damaged, please contact your
dealer.
† Wireless LAN unit
† Screw (plus head screw M2 ^ 8)
† Document CD-ROM (This Guide)
3
Safety Instructions
Thank you very much for purchasing this product. Read this document
carefully to use this unit safely and correctly. To allow you to solve any
unknown points quickly, keep this information close to hand.
So that you can use the product safely and correctly, symbols are
applied in the documentation and on the product to indicate possible
harm to the user or to others and the risk of damage to property. The
indications and their meaning are as follows. Make sure you
understand them properly before reading the guide.
Warning
This symbol indicates information that, if ignored, could
possibly result in death or personal injury due to
incorrect handling.
Caution
This symbol indicates information that, if ignored, could
possibly result in personal injury or physical damage
due to incorrect handling.
Warning
• May exert electromagnetic interference on, and cause malfunction of,
cardiac pacemakers. Before use, ensure that electromagnetic
interference does not occur.
• May exert electromagnetic interference on, and cause malfunction of,
sensitive medical equipment. Before use, ensure that electromagnetic
interference does not occur.
• Use of this product on aircraft may be restricted in some countries.
Use of this product is based on due diligence with regard to
regulations.
4
Caution
• This unit should only be used for Epson projectors. If it is installed on
another device such as a computer, it may result in computer failure,
damage, or malfunctions.
• Do not disassemble or remodel this unit. This may result in burns.
Precautions
Notes on Handling and Storage
• Do not store in locations with high temperatures or high humidity. It
may in particular be damaged or deformed if left in a vehicle with the
windows shut, or placed it locations with unusually high temperatures
for extended periods such as in direct sunlight.
• Do not get it wet. This may cause malfunctions to occur.
• Do not use near microwave ovens. Wireless communication may be
interrupted by electromagnetic interference generated by microwave
ovens.
• Do not drop it, subject it to shocks, or place heavy objects on it.
Frequency Precautions
The frequency band for this unit is 2.4 GHz/5 GHz. This frequency range
is the same frequency bandwidth as industrial, scientific, and medical
devices such as microwave ovens and mobile unit identification (RF-ID)
systems (licensed premises radio stations and unlicensed specified lowpower radio stations) used in factory production lines. Before using this
unit, check that there are no radio stations for mobile unit identification or
specified low-power radio station premises nearby. In the event that this
unit should interfere electromagnetically with the premises of a radio
station used for mobile unit recognition, cease use immediately and stop
generating the electromagnetic field. Contact your local dealer or the
nearest address provided in the Support and Service Guide supplied with
the projector if this unit interferes electromagnetically with a special lowpower radio station used for mobile unit identification or causes similar
problems.
5
Wireless Telegraphy Act Regulations
The following acts are prohibited by the Wireless Telegraphy Act.
• Modifying and disassembling (including the antenna)
• Removing the label of conformance
• IEEE 802.11a (5 GHz band) external use
International Travel Precautions
Wireless devices are designed to conform to the channel and frequency
limits of the country they are intended to be used in. This unit is based on
the specifications of the country of sale. If this unit is used outside the
country of sale, check with a local dealer for more information.
Precautions
Notes on Security when Using Wireless LAN
(Important information on customer rights (maintaining privacy))
The advantage of using a wireless LAN over a LAN cable is that, because
information is exchanged using radio signals, you can easily connect to
the network if you are within range of the radio signals. A disadvantage of
this is that within a certain range, the electromagnetic signals can pass
through barriers such as walls, so that if security countermeasures are not
implemented in some way, problems such as the following may occur.
• Communicated data can be intercepted
A third party may be able to receive wireless transmissions without
authorization, and they could obtain personal information from these
transmissions such as IDs, passwords, or credit card numbers, or they
could intercept the contents of personal e-mail messages.
• Unauthorized access to the network
A third party could access an individual or intra-company network
without permission and carry out any of the following activities.
- Retrieve personal data or other secret information (information
leakage)
- Pose as another user and send inappropriate data (impersonation)
- Overwrite the contents of intercepted data and resend it (falsification)
- Introduce a computer virus which could cause data loss or system
crashes (damage)
Initially, the possibility that such problems could occur through settings
concerning the security of the wireless LAN product and by using the
product are decreased, because the wireless LAN card and the access
point have security measures to deal with these problems. We recommend
that you use this product after making security settings using your own
judgment and assuming full responsibility, and with your full
understanding of problems that may occur if you do not make any security
settings.
See the documentation supplied with the projector for information on
security settings.
6
Installing this Unit
Installing
Install this unit into the projector.
7
losing this unit and so on, make sure you
C Tofix avoid
it in place with the screw supplied.
Procedure
the cover for the projector's wireless LAN
A Remove
unit installation section.
Screw hole for the Screw to fix the wireless LAN unit
Reading the Wireless LAN Unit Access Lamp
B Install this unit.
There are two wireless LAN unit access lamps, one on top of the projector
the other on this unit.
8
Installing this Unit
: Flashing
Status
: Lit
: Off
The Projector's
Indicator
This Unit's
Indicator
Green
Green
This unit is not installed in the
projector
This unit is installed in the projector
but not yet connected to the network
This unit is installed in the projector
and connected to the network
This unit is installed in the projector,
connected to the network, and
communicating
Green
Green
Green
(Flashing quickly)
Steps for Connecting in "Quick Connection Mode"
When this unit is installed in the projector, you can project computer
images by wirelessly connecting the projector with a computer over a
network.
Type of Network Connection
You can use the following two methods to connect a computer and the
projector over a network by using EMP NS Connection found on the
EPSON Projector Software for Meeting & Presentation CD-ROM
supplied with the projector.
f "Advanced Connection Mode"
9
When connecting in "Advanced Connection Mode" you can use the
network in the following ways.
• From a conference room, you can open and project a file stored on a
computer or file server in another room.
• You can use the Internet.
• You can monitor and control projectors on a network from the
computer.
f "Quick Connection Mode"
"Quick Connection Mode" is a mode for executing wireless LAN only.
"Quick Connection Mode" temporarily assigns the projector's SSID to a
computer creating an ad hoc connection, and after disconnecting
restores the computer's network settings.
"Advanced Connection Mode" is an infrastructure connection, and
connects to an existing network system via a network cable.
When this unit is installed in the projector, you can connect to a network
via a wireless LAN access point. If the wireless LAN access point is
WPS (Wi-Fi Protected Setup) compatible, you can easily connect the
projector to the access point and make security settings. See the
documentation supplied with the projector for more details.
This unit
Internet
LAN
Wi-Fi compliant wireless LAN card
or wireless LAN enabled computer
"Quick Connection Mode" has the following advantages.
• You can easily connect a computer to the projector and project images
from the computer without making network settings.
• This lets you connect easily without a connector cable, and you can
connect even if the projector and the computer are at remote locations.
This guide explains how to connect to a computer in "Quick Connection
Mode" and project computer images.
Steps for Connecting in "Quick Connection Mode"
Steps before Connecting in "Quick Connection
Mode"
In the following illustration, you only need to perform the light blue
sections the first time you connect.
Install EMP NS Connection on the computer to be connected
Put the computer into wireless LAN connection status
Start EMP NS Connection on the computer and connect with the
projector
10
Preparing the Computer
To use "Quick Connection Mode" to connect the projector and the
computer, you need to make the following settings on the computer.
• Install EMP NS Connection
You can find EMP NS Connection on the EPSON Projector Software
for Meeting & Presentation CD-ROM supplied with the projector. If it
is already installed, you do not need to install it again. See the
documentation supplied with the projector for the installation method.
• Put it into wireless LAN connection status
11
the port used in "Port Configurations" and
B Select
click "Apply Now".
Put the computer into wireless LAN connection
status
f For Windows
Make settings for the computer by using the utility software supplied with
the wireless LAN card. For more information on the utility software, see
the User's Guide supplied with your wireless LAN card.
f For Macintosh
Set the network port and communication status. For more details on
setting the communication status, see the User's Guides for your computer
or the AirPort card.
C Close the screen.
the communication icon at the top right of the
D Click
computer's screen, and check that the following is
displayed.
Procedure
"System Preferences" - "Network" from the
A Select
Apple menu.
The Network Configuration screen is displayed.
AirPort: On
You can connect with a Wireless LAN.
Connecting in "Quick Connection Mode" and Projecting
Operating the Projector
Before connecting, put the projector into connection standby status.
12
Operating the Computer
In the following explanations, unless otherwise noted, Windows screens
are used. You see the same screens even when using Macintosh.
Procedure
the [t] button on the remote control to turn
A onPress
the projector.
Procedure
A Start EMP NS Connection.
For Windows
B Press the [EasyMP] button on the remote control.
The EasyMP standby screen is displayed.
Select "Start" - "Programs" (or "All Programs") - "EPSON
Projector" - "EMP NS Connection".
For Macintosh
Double-click the "Applications" folder of the hard drive volume in
which EMP NS Connection is installed, and then double-click the
EMP NS Connection icon.
"Quick Connection Mode" and then click
B Select
"OK".
The projector search results are displayed. To always connect using
"Quick Connection Mode", select "Set the selected Connection
Mode as the default mode for future connections".
13
Connecting in "Quick Connection Mode" and Projecting
the projector you want to connect to, and
C Select
then click "Connect".
Projector Keyword is set to "On" from the
D When
projector, the keyword entry screen is displayed.
Enter the keyword displayed on the EasyMP
standby screen, and then click "OK".
When the connection is complete, the computer's screen is
projected. The following EMP NS Connection toolbar is displayed
on the computer screen. You can use this toolbar to operate the
projector and make settings, and to disconnect the network
connection.
From here on, see the documentation supplied with the projector
for details on using the toolbar and useful functions in EMP NS
Connection.
If the SSID configuration matches, you can connect up to four
projectors at the same time. If the projector you want to connect to
is not displayed in the search results, click the "Automatic search"
button. The search takes about 30 seconds.
q
When changing presenters and so on and when
continuously connecting from another computer, start EMP
NS Connection from the computer you want to connect and
execute "Connect". The computer that is currently
connected is disconnected, and it is then connected with the
computer that is trying to connect now.
The Target Projector is Not Found
Action 1. Restart the computer.
Action 2. Check if the projector network settings are set to "Quick
Connection Mode". See the documentation supplied with the
projector for more details.
Action 3. Check the following if actions 1 and 2 do not help.
(If it is disconnected, check the following.)
Is the indicator on the
wireless LAN unit
flashing?
Not flashing
Reinstall the wireless LAN
unit.
Flashing
Are you using
commercially available
firewall software?
Yes
Create a firewall exception
for EMP NS Connection in
the firewall software you are
using.
No
Are any of the supplied
utilities operating from
the computer's wireless
LAN card?
Close the utility and restart
EMP NS Connection.
Yes
No
Contact your local dealer or the nearest
address provided in the Support and
Service Guide supplied with the projector.
14
Please note that the projector cannot be found if the wireless LAN method
for the projector and the computer's wireless LAN card do not much, as
shown in the following examples.
Example) Projector: IEEE 802.11a Computer: IEEE 802.11b/g (a is not
compatible)
You can modify the wireless LAN method for the projector from
"Network" in the projector's configuration menu. See the documentation
supplied with the projector for more details.
Disconnecting
There are two methods of disconnecting the projector and the
computer.
Disconnecting from the Computer
Click the
button on the toolbar.
Disconnecting from the Projector
Procedure
A Press the [Esc] button on the remote control.
"Exit", and then press the [Enter] button on
B Select
the remote control.
15
This Unit's General Specifications
Conditions for Connecting to Compatible Wireless
LAN Cards and Access Points
This unit can be connected to the following products in accordance with
IEEE 802.11g, 802.11b, and 802.11a.
• Wireless LAN card
• Computers with a built-in wireless LAN function
• Access points
However, you are unlikely to be able to make an ad hoc connection for
wireless LAN equipment used with a computer in IEEE 802.11g. For
details on wireless LAN equipment see the specifications.
This Unit's General Specifications
Frequency Range *1 IEEE 802.11b/g: 2.4 GHz band (1 to 11 Ch)
IEEE 802.11a: 5.15 to 5.25 GHz (W52) and 5.25 to 5.35
GHz (W53)*2
Modulation
IEEE 802.11b : DS-SS
IEEE 802.11a/g : OFDM
Potential
Interference Range
Less than 20 m
Propriety of
Frequency Change
Can use all bands, and can avoid "licensed" and
"unlicensed" bands.
*1 You cannot use IEEE 802.11a in the People's Republic of China or the
Russian Federation.
*2 For W53 band, you can only use connections in Advanced Connection
Mode.
16
17
DECLARATION of CONFORMITY
According to 47CFR, Part 2 and 15
Class B Personal Computers and Peripherals; and/or
CPU Boards and Power Supplies used with Class B
Personal Computers
We:
Located at:
Tel:
Epson America, Inc.
3840 Kilroy Airport Way
MS: 3-13
Long Beach, CA 90806
562-290-5254
Declare under sole responsibility that the product identified herein,
complies with 47CFR Part 2 and 15 of the FCC rules as a Class B digital
device. Each product marketed, is identical to the representative unit
tested and found to be compliant with the standards. Records maintained
continue to reflect the equipment being produced can be expected to be
within the variation accepted, due to quantity production and testing on a
statistical basis as required by 47CFR 2.909. Operation is subject to the
following two conditions :
Trade Name:
EPSON
Type of Product:
Wireless LAN Unit
Model
:ELPAP03
FCC Compliance Statement
For United States Users
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
or television reception. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause
interference to radio and television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures.
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
WARNING
The connection of a non-shielded equipment interface cable to this
equipment will invalidate the FCC Certification or Declaration of this
device and may cause interference levels which exceed the limits
established by the FCC for this equipment. It is the responsibility of the
user to obtain and use a shielded equipment interface cable with this
device. If this equipment has more than one interface connector, do not
leave cables connected to unused interfaces. Changes or modifications
not expressly approved by the manufacturer could void the userís
authority to operate the equipment.