Royal Sovereign RSC-1400L Owner`s manual

16. WARRANTY
Royal Sovereign International warrants the equipment sold is free from defects in
material and workmanship for a period of One (1) year for Parts and Labor from the date
of installation, excluding lamination rollers which are warranted for Six (6) months. This
warranty is extended only to the original purchaser. This warranty is the only warranty
made by Royal Sovereign International and cannot be modified or amended. Royal
Sovereign’s sole and exclusive liability and the customer’s sole and exclusive remedy
under this warranty shall be, at Royal Sovereign’s option, to repair or replace any such
defective part or product. These remedies are only available if Royal Sovereign’s
examination of the product discloses to Royal Sovereign’s satisfaction that such defects
actually exist and were not caused by misuse, neglect, attempt to repair, unauthorized
alternation or modification, incorrect line voltage, fire, accident, flood or other hazard.
All warranty claims must be filed through the authorized Royal Sovereign dealer or
reseller through which the equipment was originally purchased. Model, serial number
and date of delivery are required for all claims.
OWNER'S MANUAL
RSC-1400L Laminators
The warranty made herein is in lieu of all other warranties, expressed or implied,
including any warranty or merchantability or fitness for a particular purpose. Royal
Sovereign will not be liable for personal damage or personal injury (unless primarily
caused by its negligence), loss of profit, or other incidental or consequential damages
arising out of the use or inability to use this equipment.
LIMITED WARRANTY
This warranty specifically does not cover damage to laminating rollers caused by knives,
razor blades, or any sharp objects or abrasives, or failure caused by adhesives, or
damage caused by lifting, tilting or improper use of the machine. Warranty repair or
replacement by Royal Sovereign or its authorized Reseller(s) does not extend the
warranty beyond the initial one year period from the date of installation. Unauthorized
customer alterations will void this warranty.
CORPORATE HEADQUARTERS
Royal Sovereign International Inc.
2 Volvo Drive, Rockleigh, NJ 07647 U.S.A.
TEL : +1 ) 800-397-1025
FAX : +1 ) 201-750-1022
E-mail : info@royalsovereign.com
RS Holland B.V.
Royal Sovereign Inc. <Oversea Sales Office>
Planetenweg 75 2132HM Hoofddorp, The Netherlands.
TEL : +31) 23-5626620, +31) 23-5654451
FAX : +31) 23-5654565
E-mail : purchaseorder@royalsovereign.com
1001, World Meridian II, 426-5, Gasan-dong,
Geumcheon-gu, Seoul, 153-759, KOREA
TEL : +82)2-2025-8800 FAX : +82)2-2025-8830
E-mail : sales@royalsovereign.com
RS Canada Inc.
RS International Australia PTY. LTD.
164 Oakdale Road, Toronto, Ontario M3N 2S5
CANADA
TEL : +1 ) 416-741-8400 FAX : +1 ) 416-741-8185
E-mail : info@royalsovereign.com
30 Prime Drive, Seven Hills, NSW 2147, Australia
TEL : +61) 2-9674-2127
FAX : +61) 2-9674-2027
E-mail : salesaust@royalsovereign.com
19
Read all instructions carefully before use.
For any Customer Support needs please choose the
Customer Support tab on www.royalsovereign.com
Royal Sovereign International Inc.
www.royalsovereign.com
RSC-1400L
TABLE OF CONTENTS
TOPIC
1. INTRODUCTION
PAGE
1. Introduction.......................................................................................................... 2
2. Safety Precautions ............................................................................................... 2
3. Installation ............................................................................................................ 3
Thank you for choosing a Royal Sovereign laminator. It has been designed and
manufactured to provide years of continuous service. For complete operating and
maintenance information please read this manual thoroughly. Upon receipt of your
laminator, please inspect the box, the machine and all other contents for shipping
damage. Damage should be brought to the immediate attention of the delivering carrier
(See page 4 for list of shipment elements).
4. Included with Laminator ....................................................................................... 4
5. Product Identification.............................................................................................5
6. Control Panel........................................................................................................ 6
2. SAFETY PRECAUTIONS
7. Roller Nip Settings................................................................................................ 7
Failure to comply with any of the following safety procedures could result in serious injury.
Please read the instructions carefully and kee p for future reference.
8. Using Foot Pedal and Remote Control................................................................ 8
1. Only a licensed electrician should install wiring and outlet for the laminator.
9. Using Cross Cutter .............................................................................................. 9
2. Ensure the unit is plugged into a properly grounded outlet with the correct voltage.
10. Loading Film..................................................................................................... 10
3. Keep hands and clothing (i.e. Neckties) away from rollers.The rollers are pinch points
that can trap body parts or clothing and cause serious injury.
11. Threading Film
11.1. Decaling .................................................................................................. 11
11.2. Mounting.................................................................................................. 13
4. Keep flammable and wet objects away from the machine.
12. Installation of the Front Feed and Rear Rewind Options ................................ 15
7. Ensure the unit is turned off, cooled, and unplugged from the outlet prior to moving
and/or repairing.
13. Maintenance..................................................................................................... 17
8. Keep out of reach of children.
14. Troubleshooting ............................................................................................... 17
15. Specifications ................................................................................................... 18
16. Warranty........................................................................................................... 19
5. Place machine on a level surface.
6. Avoid excessive sunlight, humidity and extreme temperatures.
9. Only Royal Sovereign authorized maintenance and service technicians should make
repairs.
10. Do not attempt to laminate items that exceed total recommended material thickness
for the unit
11. When cleaning the machine, don't use flammable sprays or materials.
12. Do not touch the rollers when they are hot or place foreign objects inside the machine.
13. Do not cover the surface of the machine until the machine has completely cooled.
1
2
RSC-1400L
3. INSTALLATION
4. INCLUDED WITH LAMINATOR
Note: The laminator should be installed by a trained service technician.
The laminator comes fully assembled, except for the feed table, paper guide. Upon arrival,
thoroughly inspect the unit. It is imperative that any shipping damage is reported and a
claim is filed with the delivering carrier immediately upon receipt.
The laminator should be located in an area with adequate work space for feeding graphics
and lamination materials.
Avoid placing the laminator in a dusty area or near sources of extreme heat or cold.
Once the laminator is in place, lock the casters into position(“ON” position). Always unlock
the casters (“OFF” position) when moving to a different location.
Thoroughly inspect the parts and the unit. It is imperative that any missing parts are
reported and a claim is filed with the reseller immediately upon receipt of shipment.
Part Name
Quantity
Laminator
1
Owner's Manual
1
3´´(76mm) / 2" (57mm) Auto Grip
6/4
L-wrench (2.5)
1
Dust Cover
1
ELECTRICAL REQUIREMENTS
Royal Sovereign recommends that a licensed electrician ensuresproper power installation
to your laminator in accordance with electrical codes in your area.
The laminator should have a dedicated power line.
MODEL
Power Supply
RSC-1400L
220-240V
50/60HZ
Spare Motor Fuse - FUSE(50T)
(6.3A)
Spare Main Power Fuse - FUSE(65TS)
(5A)
8 - 1/4"Hexa head Bolt (M6 20mm)
8 - Spring Washer( 6.1)
(Included with option only)
12 - 3/16"screw (M5 10mm).
12 - Spring Washer( 5.1)
(Included with option only)
1
1
@?hf
/Xe@??W.?h
V/X?@?W.Y?h
?V/?@?.Yhe
W.?/X?he
?W.Y?V/Xhe
?.Y?eV/he
120V
50/60HZ
?@h
J5h
?O&Hh
O2@@@@@?O@g
W2@0M??W@@@@g
?W&(M?e?7<I'@g
?7@Hf?@eN@g
J@5?fJ5e?@g
7@H?f7Hhe
@@g@?he
@@f?J5?he
@@f?7H?he
@@f?@hf
3@L?eJ5hf
N@1?e7Hhf
?3@Le@?fW.g
?V')KC5?e?O.Yg
V4@@Y??O20Y?g
?@@@@0M?h
J(M?hf
7Hhg
@?hg
single phase
10/10
@?hf
/Xe@??W.?h
V/X?@?W.Y?h
?V/?@?.Yhe
W.?/X?he
?W.Y?V/Xhe
?.Y?eV/he
?@h
J5h
?O&Hh
O2@@@@@?O@g
W2@0M??W@@@@g
?W&(M?e?7<I'@g
?7@Hf?@eN@g
J@5?fJ5e?@g
7@H?f7Hhe
@@g@?he
@@f?J5?he
@@f?7H?he
@@f?@hf
3@L?eJ5hf
N@1?e7Hhf
?3@Le@?fW.g
?V')KC5?e?O.Yg
V4@@Y??O20Y?g
?@@@@0M?h
J(M?hf
7Hhg
@?hg
12/12
Front Feeder and Rear Rewinder Kit
(Included with option only)
2/2
4 - 1/3"Hexa head Bolt (M8 70mm)
4 - Spring Washer( 8.5)
(Included with option only)
4 - 1/3"screw (M8 60mm).
4 - Spring Washer( 8.5)
(Included with option only)
@?hf
/Xe@??W.?h
V/X?@?W.Y?h
?V/?@?.Yhe
W.?/X?he
?W.Y?V/Xhe
?.Y?eV/he
120V UL
230V UL
240V UK
?@h
J5h
?O&Hh
O2@@@@@?O@g
W2@0M??W@@@@g
?W&(M?e?7<I'@g
?7@Hf?@eN@g
J@5?fJ5e?@g
7@H?f7Hhe
@@g@?he
@@f?J5?he
@@f?7H?he
@@f?@hf
3@L?eJ5hf
N@1?e7Hhf
?3@Le@?fW.g
?V')KC5?e?O.Yg
V4@@Y??O20Y?g
?@@@@0M?h
J(M?hf
7Hhg
@?hg
4
?@h
J5h
?O&Hh
O2@@@@@?O@g
W2@0M??W@@@@g
?W&(M?e?7<I'@g
?7@Hf?@eN@g
J@5?fJ5e?@g
7@H?f7Hhe
@@g@?he
@@f?J5?he
@@f?7H?he
@@f?@hf
3@L?eJ5hf
N@1?e7Hhf
?3@Le@?fW.g
?V')KC5?e?O.Yg
V4@@Y??O20Y?g
?@@@@0M?h
J(M?hf
7Hhg
@?hg
4
@?hf
/Xe@??W.?h
V/X?@?W.Y?h
?V/?@?.Yhe
W.?/X?he
?W.Y?V/Xhe
?.Y?eV/he
W.h
?W&Hh
?75?h
J@H?h
75he
?J@Hhe
?7@?he
?@@?he
?@@?he
?@@?he
?@@?he
?@@?he
?@@?he
?3@?he
?N@Lhe
31he
N@L?h
?31?h
?V'Lh
V/h
NUT M8)
220V EU
4
220V AU
3
4
Picture
RSC -1400L
5. PRODUCT IDENTIFICATION
6. CONTROL PANEL
When the machine is initially turned on, the LED display window will show the speed.
12
2
1
3
4
11
10
9
5
?
?
?
?
?
?
?
?
?
?
?
?
?
?O2@h?
?@@@@@h?
@@h?
@@h?
@@h?
@@h?
@@h?
@@h?
@@h?
@@h?
@@h?
@@h?
@@h?
@@h?
?@@@@@@@@?f?
?
?
?
?
?
6
8
?
?
?
?
?
?
?
?
?
?
?
?
?
W2@@6Xg?
?W&@@@@)X?f?
?7(M?I'@1?f?
?@H?eN@@?f?
?@f?@@?f?
?@@?f?
J@5?f?
7(Y?f?
?J(Yg?
W.Y?g?
?W.Yh?
W.Y?e@?f?
?W&Yf@?f?
W&@@@@@@@?f?
&@@@@@@@@?f?
?
?
?
?
?
13
?
?
?
?
?
?
?
?
?
?
?
?
?
W2@6X?g?
?W&@@@)Xg?
?.M??I'1g?
N@g?
?@g?
J5g?
?O&Yg?
?@@@@@@?f?
I'@?f?
?N@?f?
@?f?
?J5?f?
W.Y?f?
?'6K?O.Yg?
?V4@@0Y?g?
?
?
?
?
?
7
?
?
?
?
?
?
?
?
?
?
?
?
?
W&g?
?W&@g?
W&@@g?
?W.Y@@g?
W.Y?@@g?
?W.Ye@@g?
O.Y?e@@g?
?@@Yf@@g?
?@@@@@@@@@@@f?
?@@@@@@@@@@@f?
@@g?
@@g?
@@g?
@@g?
@@g?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?@@@@@@@f?
?@@@@@@@f?
J(M?h?
7Yhe?
@@6Kh?
@@@@6Xg?
?I4@@)X?f?
?I4@1?f?
@?f?
@?f?
@?f?
?J5?f?
W.Y?f?
?'6K?O.Yg?
?V4@@0Y?g?
?
?
?
?
?
RSC-1400L
NO.
PART NAME
RSC-1400L
1
SAFETY COVER
O
2
EMERGENCY SWITCH
O
3
FRAME-PAPER GUIDE
O
4
TABLE-FRONT
O
5
MAIN ROLLER
O
6
ASSEMBLY STAND
O
7
FOOT PEDAL
O
8
TENSION CONTROL KNOBS
O
9
PRESSURE LEVER
O
10
CONTROL PANEL
O
11
UPPER IDLE BAR
O
12
RELEASE LINER TAKE UP
O
13
REMOTE CONTROL
O
5
Control Buttons
1. SPEED DISPLAY: Display’s current Speed.
2. SPEED BUTTON: Adjusting the speed of the rollers. To change the speed of the rollers,
press the up or down arrow button.
3. RUN: To start the rollers.
4. STOP: To stop the rollers.
5. REV: To reverse the rollers, press and hold the REVERSE button.
6
RSC-1400L
7. ROLLER NIP SETTING
It is important to adjust the roller nip settings to the appropriate thickness of the board
being used. Use the guide below to adjust to the correct position.
8. USING FOOT PEDAL AND REMOTE CONTROL
USING FOOT PEDAL
Place the foot pedal on the floor in front of the
NO.
Inches
Metric
(mm)
1
Lamination
Lamination
may use the foot pedal to operate the laminator for
2
1/ 25"
1
“Hands Free Operation.” To activate the machine,
3
3/16"~1/4"
5-7
press the foot pedal once and then release. Repeat
4
3/ 8"~1/2"
10-13
5
3/5"
15
machine. Once all correct settings are displayed, you
to stop the rollers.
NOTE: If you don't want to
laminate,please place the
pressure lever to the "Open
position(NO.5)".
USING REMOTE CONTROL
1
Located on the rear left side of the laminator.
1. PRESS RUN – To activate the rollers.
2. PRESS STOP – To stop the rollers from turning.
3. PRESS REV – To reverse the rollers. Press and
hold the button (useful for jams or misted media).
7
8
2
3
RSC-1400L
9. USING CROSS CUTTER
10. LOADING FILM
Royal Sovereign films are wound with the adhesive side facing the inside of the roll
(adhesive in).
The cross cutter is located in the rear exit table of the machine.
Loading films to upper and lower film shafts:
(See page 5 for assistance with parts identification.)
1. After lamination, move the cutter approximately to
the center of the completed application at the
desired point of detachment (Figure 1).
Figures 1
1. Adjust the auto grip to fit to the film and tighten the
auto grip screw (Figure 1).
Figure 1
2. Grasp film with one hand, press the cutter
downward into the application and slide it first to
one end of the application, then to the other end to
complete the cut (Figure 2 & 3).
2. Remove the upper and lower film shafts from the
machine and load the films (Center the upper and
lower films on the shaft). Note the direction of the
adhesives on the lower and upper films
(Figure 2).
Figures 2
Figure 2
3. Load the upper and lower film shafts on the
machine (Figure 3).
Figure 3
Figures 3
9
10
RSC-1400L
11. THREADING FILM
8. Cut and separate the release liner and the film.(Figure
3)
Figure 3
9. Thread the craft paper behind the Lower Idle Bar to
the top film that is resting on the main roller (do not
use the Lower Idle Bar for Mounting). (Figure 4)
11.1. Decaling
10. Reinstall the Feed Table and the Frame-Paper
Guide,and close the Safety Cover.
1. Turn the power switch on (“I” position). The Power
switch is located on the rear left side of the unit.
Figure 4
11. Adjust the nip setting to appropriate gap.
2. Complete the steps as in the “LOADING FILM”
section (see page 10).
12. Insert and push the leader board until they reach the
front nip point.
3. Take off the Frame-Paper Guide and the Feed Table.
13. Push the Run button.
4. Pull the top film down over the Safety Cover to the
bottom of the craft paper / Mounting film.
Figure 1
5. Align and center the craft paper / Mounting film to the
top film and tighten the two lower core screws (Figure
1).
15. Adjust the top and bottom tension knob by rotating it
clockwise or counterclockwise. Turn it until the top
and bottom roll films have some resistance varies
(the tension depending on the film thickness; the
thicker the film the more tension is required).
(Figure 6)
6. Thread the top film underneath the Upper Idle
Bar.(Figure 2)
7. Tape the top film on to the Release Liner TakeUp.(Figure 2)
11
14. Push the leader board into the rollers. (Figure 5)
Figure 2
12
Figure 5
Figure 6
RSC-1400L
16. Press the Stop button when the leader board has completely exited from the rollers.
4. Flip the image over the top roller and hold on to the
release liner (Figure 4).
17. Use the Cross Cutter to cut the leader board from the web (see page 9).
18. Set the nip setting to the appropriate position for the Over-lamination / Decaling
application.
Figure 4
11.2. Mounting
1. Lay the decaled image face down on a flat surface.
5. Press the foot pedal once, and then let it go while
Carefully peel back and put a crease along the
slowly pulling the release liner as the board enters
edge of the release liner ( Approximately 1 in or
the main roller nip (Figure 5)
25mm, Figure 1).
Figure 1
6. Press the foot pedal once again when the board has
completely exited from the rear of the unit. Trim the
2. With the image facing up, align the image onto the
board if necessary.
board. Press firmly from the center out (Figure 2).
Figure 2
3. Adjust the pressure lever to ensure the proper
opening (Figure 3).
Figure 3
13
14
Figure 5
RSC-1400L
12. INSTALLATION OF FRONT FEEDER and REAR
REWINDER OPTIONS
Note: Below options are to be installed by an authorized RS reseller.
4. Disassemble the power switch bracket and place the left
rewinder outside of the frame; fasten with round head
3/16"(M5) screws (included in the option kit). Then,
reinstall the power switch bracket (Figure 7).
Installation of the Front Feeder Option (Includes 2 brackets,
one spindle, and mounting hardware).
Figure 7
1. Install the Front Feeder to the inside of the front frames
using four 1/4"(M6) hexagon bolts on each side (Figure 1)
Figure 1
5. Install the right rewinder on the outside of the frame and
connect the motor wire connector to the rear wire
(Figures 8 & 9).
Figure 8
Installing the Rear Rewinder Option (Includes motorized
winder, bracket, one spindle, and mounting hardware).
1. Remove the left and right covers by using a Phillips
screwdriver (four screws on each side cover) (Figures 2 &
3).
6. Reinstall the rear cover.
7. Reinstall the side covers.
Figure 2
Figure 3
8. Reinstall the lever knob and screw.
Figure 9
2. Remove the lever knob screw and lever (Figure 4).
Figure 4
3. Remove the rear cover by removing all
10 screws (4 top, 4 bottom, and 1 on
each side) (Figure 5 & 6).
Figure 5
15
Figure 6
16
RSC -1400L
13. MAINTENANCE
15. SPECIFICATIONS
Cleaning the Body of the laminaor
1.To clean the machine body, dampen a cloth with water only and gently wipe the
machine clean.
Removing Adhesive Build Up
1. Remove the film from the laminator.
2. Use a damp (water only) cloth and a rubber gum eraser to remove the adhesive on the
Teflon (metal) and silicone rollers.
Note: Rub firmly but do not scrub the rollers vigorously as this may scratch the
surface.Do not use sharp metal objects, steel wool, or abrasives, as these
may also damage the rollers.
Lubrication
1. Drive chain and sprockets should be lubricated with either a light coat of gear lube or
heavy grease (lithium grease) after 6 months or 1000 hours of operation, whichever
comes first.
14. TROUBLESHOOTING
Symptom
Machine will not turn
on:
There is power, but the
rollers are not turning
after the “RUN” button
is pressed:
Cause
Possible Solution
a. Power plug is not plugged in.
b. Power switch is in “0” (Off) position.
c. Tripped circuit breaker.
d. Blown main power fuse.
a. Emergency switch (es) is (are)
engaged.
b. Paper guide is not installed correctly.
c. Blown motor fuse.
a. Plug the power cord into appropriate
outlet.
b. Put the power switch to the “I” (On)
position.
c. Reset the circuit breaker.
d. Replace the fuse.
a. Disengage the emergency switch (es).
b. Properly install the paper guide so that
the micro switch is activated.
d. Replace the motor fuse.
Description
RSC-1400L
Power supply
AC 100, 200, 220~240V 50/60Hz 120V 60Hz
Power consumption
100W
Max laminating width
1400mm / 55"
Film thickness
60~500 mic / 1~15mil
Max laminating speed
5m/min / 16.4ft/min
Ready time
Not applicable
Heating method
None
Driving motor
DC geared
Max Temperature control
Not applicable
9 settings
Speed control
Transport type
2 Roller
Film core size
Auto grip (2",3")
Cross cutter
Yes
Hot lamination
No
Cold lamination
Yes
Mounting thickness
15mm / 0.6"
Take up system
Chain link to main motor
Reverse
Yes
Remote control
Yes
Foot pedal
Yes
Unit dimensions
(w x d x h)
1710 650 1210 (mm)
67.5" 21.5" 47.5"
?/X?gW.h
?V/Xf?W.Yh
V/X?eW.Y?h
?V/X?W.Yhe
V/T.Y?he
?S@Uhf
W.R/X?he
?W.Y?V/Xhe
W.Y?eV/X?h
?W.Yf?V/Xh
?.Y?gV/h
Unit weight
a. Did not raise the temperature.
a. Raise the temperature.
Curled lamination:
a. Upward curl.
b. Downward curl.
a. Loosen the top roll film tension.
b. Loosen the bottom roll film tension.
17
?/X?gW.h
?V/Xf?W.Yh
V/X?eW.Y?h
?V/X?W.Yhe
V/T.Y?he
?S@Uhf
W.R/X?he
?W.Y?V/Xhe
W.Y?eV/X?h
?W.Yf?V/Xh
?.Y?gV/h
210kg / 462.9bs
Carton dimensions
(w x d x h)
The unit is not heating
up:
?/X?gW.h
?V/Xf?W.Yh
V/X?eW.Y?h
?V/X?W.Yhe
V/T.Y?he
?S@Uhf
W.R/X?he
?W.Y?V/Xhe
W.Y?eV/X?h
?W.Yf?V/Xh
?.Y?gV/h
?/X?gW.h
?V/Xf?W.Yh
V/X?eW.Y?h
?V/X?W.Yhe
V/T.Y?he
?S@Uhf
W.R/X?he
?W.Y?V/Xhe
W.Y?eV/X?h
?W.Yf?V/Xh
?.Y?gV/h
1960 900 850(mm)
77" 35.5" 33.5"
?/X?gW.h
?V/Xf?W.Yh
V/X?eW.Y?h
?V/X?W.Yhe
V/T.Y?he
?S@Uhf
W.R/X?he
?W.Y?V/Xhe
W.Y?eV/X?h
?W.Yf?V/Xh
?.Y?gV/h
?/X?gW.h
?V/Xf?W.Yh
V/X?eW.Y?h
?V/X?W.Yhe
V/T.Y?he
?S@Uhf
W.R/X?he
?W.Y?V/Xhe
W.Y?eV/X?h
?W.Yf?V/Xh
?.Y?gV/h
Gross Weight
?/X?gW.h
?V/Xf?W.Yh
V/X?eW.Y?h
?V/X?W.Yhe
V/T.Y?he
?S@Uhf
W.R/X?he
?W.Y?V/Xhe
W.Y?eV/X?h
?W.Yf?V/Xh
?.Y?gV/h
?/X?gW.h
?V/Xf?W.Yh
V/X?eW.Y?h
?V/X?W.Yhe
V/T.Y?he
?S@Uhf
W.R/X?he
?W.Y?V/Xhe
W.Y?eV/X?h
?W.Yf?V/Xh
?.Y?gV/h
292kg / 643.7lbs
18