Draytek VigorPro 5300VS Installation guide

i
VigorIPPBX 3510 Quick Start Guid
VigorIPPBX 3510 Quick Start Guide
ii
VigorIPPBX 3510
Quick Start Guide
Version: 2.0
Date: 19/11/2010
iii
VigorIPPBX 3510 Quick Start Guid
Copyright Information
Copyright
Declarations
Copyright 2010 All rights reserved. This publication contains information that is
protected by copyright. No part may be reproduced, transmitted, transcribed,
stored in a retrieval system, or translated into any language without written
permission from the copyright holders.
Trademarks
The following trademarks are used in this document:
z
Microsoft is a registered trademark of Microsoft Corp.
z
Windows, Windows 95, 98, Me, NT, 2000, XP, Vista and Explorer are
trademarks of Microsoft Corp.
z
Apple and Mac OS are registered trademarks of Apple Inc.
z
Other products may be trademarks or registered trademarks of their
respective manufacturers.
Safety Instructions and Approval
Safety
Instructions
Warranty
z
z
Read the installation guide thoroughly before you set up the router.
The router is a complicated electronic unit that may be repaired only be
authorized and qualified personnel. Do not try to open or repair the router
yourself.
z
Do not place the router in a damp or humid place, e.g. a bathroom.
z
Do not stack the routers.
z
The router should be used in a sheltered area, within a temperature range
of +5 to +40 Celsius.
z
Do not expose the router to direct sunlight or other heat sources. The
housing and electronic components may be damaged by direct sunlight or
heat sources.
z
Do not deploy the cable for LAN connection outdoor to prevent electronic
shock hazards.
z
Keep the package out of reach of children.
z
When you want to dispose of the router, please follow local regulations on
conservation of the environment.
We warrant to the original end user (purchaser) that the router will be free from
any defects in workmanship or materials for a period of two (2) years from the
date of purchase from the dealer. Please keep your purchase receipt in a safe
place as it serves as proof of date of purchase. During the warranty period, and
upon proof of purchase, should the product have indications of failure due to
faulty workmanship and/or materials, we will, at our discretion, repair or replace
the defective products or components, without charge for either parts or labor, to
whatever extent we deem necessary tore-store the product to proper operating
condition. Any replacement will consist of a new or re-manufactured
functionally equivalent product of equal value, and will be offered solely at our
discretion. This warranty will not apply if the product is modified, misused,
tampered with, damaged by an act of God, or subjected to abnormal working
conditions. The warranty does not cover the bundled or licensed software of
other vendors. Defects which do not significantly affect the usability of the
product will not be covered by the warranty. We reserve the right to revise the
manual and online documentation and to make changes from time to time in the
contents hereof without obligation to notify any person of such revision or
changes.
Be a Registered
Owner
Web registration is preferred. You can register your Vigor router via
http://www.draytek.com.
Firmware & Tools
Updates
Due to the continuous evolution of DrayTek technology, all routers will be
regularly upgraded. Please consult the DrayTek web site for more information on
newest firmware, tools and documents.
http://www.draytek.com
VigorIPPBX 3510 Quick Start Guide
iv
European Community Declarations
Manufacturer:
Address:
Product:
DrayTek Corp.
No. 26, Fu Shing Road, HuKou Township, HsinChu Industrial Park, Hsin-Chu County,
Taiwan 303
VigorIPPBX 3510
DrayTek Corp. declares that VigorIPPBX 3510 is in compliance with the following essential requirements
and other relevant provisions of R&TTE Directive 1999/5/EEC.
The product conforms to the requirements of Electro-Magnetic Compatibility (EMC) Directive
2004/108/EC by complying with the requirements set forth in EN55022/Class A and EN55024/Class A.
The product conforms to the requirements of Low Voltage (LVD) Directive 2006/95/EC by complying
with the requirements set forth in EN60950-1.
Regulatory Information
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the interference
by one of the following measures:
z
Reorient or relocate the receiving antenna.
z
Increase the separation between the equipment and receiver.
z
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
z
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device may accept any interference received, including interference that may cause undesired
operation.
Please visit http://www.draytek.com/user/AboutRegulatory.php.
This product is designed for POTS network throughout the EC region and Switzerland. Please see the user
manual for the applicable networks on your product.
v
VigorIPPBX 3510 Quick Start Guid
VigorIPPBX 3510 Quick Start Guide
vi
Table of Contents
1. Introduction........................................................................................................... 1
1.1 Panel Explanation ...................................................................................................................... 2
1.2 Package Content........................................................................................................................ 4
2. Installing Your Router........................................................................................... 5
2.1 Hardware Installation.................................................................................................................. 5
2.2 Printer Installation....................................................................................................................... 6
3. Configuring Web Pages ......................................................................................11
4. Trouble Shooting ................................................................................................ 17
4.1 Checking If the Hardware Status Is OK or Not......................................................................... 17
4.2 Checking If the Network Connection Settings on Your Computer Is OK or Not ...................... 18
4.3 Pinging the Router from Your Computer .................................................................................. 20
4.4 Checking If the ISP Settings are OK or Not ............................................................................. 21
4.5 Backing to Factory Default Setting If Necessary...................................................................... 23
4.6 Contacting Your Dealer ............................................................................................................ 24
vii
VigorIPPBX 3510 Quick Start Guid
VigorIPPBX 3510 Quick Start Guide
viii
1. Introduction
The VigorIPPBX 3510 is a dual-WAN broadband router with IP PBX function. The 2nd
WAN interface is shared with the 4th LAN port. These two WANs can connect to
DSL/Cable modem or fiber media converter for policy-based load-balance, fail-over and
BoD (Bandwidth on Demand); it also features advanced bandwidth control mechanism
such as IP-layer QoS, NAT Session Limitation, Bandwidth Borrowed, etc., to allow easy,
flexible, reliable access control and bandwidth management.
VigorIPPBX 3510 is an IPPBX device which must connect to a router by WAN port for
accessing into Internet.
The SPI (Stateful Packet Inspection) firewall on VigorIPPBX 3510 uses object-based
design to make settings of firewall policies easy. The CSM (Content Security
Management) feature allows more precise and efficient access control for URL/Web
Content Filtering, IM (Instant Messenger) and P2P (Peer to Peer) applications.
With hardware-based implementation of the VPN protocols, the VigorIPPBX 3510
supports up to 32 VPN tunnels using advanced protocols such as IPSec/PPTP/L2TP with
AES/DES/3DES for encryption and MD5/SHA-1 for authentication.
VigorIPPBX 3510 can provide up to 100 extensions setup to let all IP phones register to
LAN or remote sites around the world to have unlimited free calls through Internet.
Moreover, VigorIPPBX 3510 is able to establish multiple networking architectures
corresponding to your current desire and future needs of growing communication. Its
PSTN compatibility lets you move from simple VoIP solution such as IP phone and
Softphone to integrate with comprehensive networking infrastructure, such as Analog
phone line any time you need.
1
VigorIPPBX 3510 Quick Start Guide
1.1 Panel Explanation
Description for LED
LED
Status
Explanation
PWR (Power)
On
Off
Blinking
Off
On
Blinking
On
Off
The router is powered on.
The router is powered off.
The router is powered on and running normally.
The router is not ready or failed.
The WAN connection is ready.
It will blink while transmitting data.
CDR utility has been installed and is recording.
CDR utility has not been installed and is unable to
record.
A USB device is connected and active.
The data is transmitting.
ACT (Activity)
WAN
CDR
USB
MSF
VPN
CSM
On
Blinking
Blinking
On
On
QoS
On
The VPN tunnel is active.
The profiles of CSM (Content Security Management)
for IM/P2P, URL Content Filter, Web Content Filter
application is enabled from Firewall >> General
Setup. (These profile can be established under CSM
menu).
The QoS function is active.
On
Off
Blinking
On
Off
On
Off
Blinking
On
Off
The port is connected.
The port is disconnected.
The data is transmitting.
The port is connected with 100Mbps.
The port is connected with 10Mbps.
The port is connected.
The port is disconnected.
The data is transmitting.
The port is connected with 100Mbps.
The port is connected with 10Mbps.
Storage (NAND flash or USB disk) is full.
LED on Connector
LAN 1/2/3/4*
Left LED
(Green)
Right LED
(Green)
WAN1/2*
Left LED
(Green)
Right LED
(Green)
* LAN 4 and WAN 2 share the same connector.
VigorIPPBX 3510 Quick Start Guide
2
Description for Connectors
Interface
Factory Reset
FXS
FXO
LAN (1-4)
WAN
USB
PWR
ON/OFF
Description
Restore the default settings.
Usage: Turn on the router (ACT LED is blinking). Press the hole and keep for more
than 5 seconds. When you see the ACT LED begins to blink rapidly than usual,
release the button. Then the router will restart with the factory default configuration.
Connecter for telephone set.
Connecter for FXS interface of PABX or PSTN line.
Connecters for local networked devices.
Connecter for accessing Internet.
Connecter for a USB device (for 3G USB Modem or printer).
Connecter for a power cord.
Power switch.
3
VigorIPPBX 3510 Quick Start Guide
1.2 Package Content
n Quick Start Guide
o CD
p RJ-45 Cable (Ethernet)
q Rack mount kit (brackets)
r FXO (optional)
sFXS (optional)
tThe type of the power cord depends on the country that the router will be installed.
UK-type power cord
EU-type power cord
USA/Taiwan-type power cord
AU/NZ-type power cord
China-type power cord
VigorIPPBX 3510 Quick Start Guide
4
2. Installing Your Router
This section will guide you to install the router through hardware connection and
configure the router’s settings through web browser.
2.1 Hardware Installation
Before starting to configure the router, you have to connect your devices correctly.
1.
Connect the cable Modem/DSL Modem/Media Converter to WAN port of router
with Ethernet cable (RJ-45).
2.
Connect one end of an Ethernet cable (RJ-45) to one of the LAN ports of the router
and the other end of the cable (RJ-45) into the Ethernet port on your computer.
3.
Connect the telephone sets with phone lines (for using PBX function). For the model
without phone ports, skip this step.
4.
Connect IP Phone(s) via VigorSwitch to this router.
5.
Connect one end of the power adapter to the router’s power port on the rear panel,
and the other side into a wall outlet.
6.
Power on the device by pressing down the power switch on the rear panel.
7.
The system starts to initiate. After completing the system test, the PWR and ACT
LEDs will light up and start blinking.
(Below we take VigorIPPBX 3510 as an example for hardware installation.)
5
VigorIPPBX 3510 Quick Start Guide
2.2 Printer Installation
You can install a printer onto the router for sharing printing. All the PCs connected this
router can print documents via the router. The example provided here is made based on
Windows XP/2000/Vista. For Windows 98/SE, please visit www.draytek.com.
Before using it, please follow the steps below to configure settings for connected
computers.
1.
Connect the printer with the router through USB/parallel port.
2.
Open Start->Settings-> Printer and Faxes.
VigorIPPBX 3510 Quick Start Guide
6
3.
Open File->Add a New Computer. A welcome dialog will appear. Please click
Next.
4.
Click Local printer attached to this computer and click Next.
5.
In this dialog, choose Create a new port Type of port and use the drop down list to
select Standard TCP/IP Port. Click Next.
7
VigorIPPBX 3510 Quick Start Guide
6.
In the following dialog, type 192.168.1.1 (router’s LAN IP) in the field of Printer
Name or IP Address and type IP_192.168.1.1 as the port name. Then, click Next.
7.
Click Standard and choose Generic Network Card.
8.
Then, in the following dialog, click Finish.
VigorIPPBX 3510 Quick Start Guide
8
9.
Now, your system will ask you to choose right name of the printer that you installed
onto the router. Such step can make correct driver loaded onto your PC. When you
finish the selection, click Next.
10. For the final stage, you need to go back to Control Panel-> Printers and edit the
property of the new printer you have added.
11. Select "LPR" on Protocol, type p1 (number 1) as Queue Name. Then click OK.
Next please refer to the red rectangle for choosing the correct protocol and LPR
name.
9
VigorIPPBX 3510 Quick Start Guide
The printer can be used for printing now. Most of the printers with different
manufacturers are compatible with vigor router.
Note 1: Some printers with the fax/scanning or other additional functions are not
supported. If you do not know whether your printer is supported or not, please visit
www.draytek.com to find out the printer list. Open Support >FAQ; find out the link
of Printer Server and click it; then click the What types of printers are
compatible with Vigor router? link.
Note 2: Vigor router supports printing request from computers via LAN ports but not
WAN port.
VigorIPPBX 3510 Quick Start Guide
10
3. Configuring Web Pages
To access Internet, please finish basic configuration after completing the hardware
installation.
The Quick Start Wizard is designed for you to easily set up your router for Internet
access. You can directly access the Quick Start Wizard via Web Configurator.
1.
Make sure your PC connects to the router correctly.
Notice: You may either simply set up your computer to get IP dynamically
from the router or set up the IP address of the computer to be the same
subnet as the default IP address of Vigor router 192.168.1.1. For the
detailed information, please refer to the later section - Trouble Shooting of
the guide.
2.
Open a web browser on your PC and type http://192.168.1.1. A pop-up window will
open to ask for username and password. Please type “admin” as the username and
leave blank for the password on the window. Next click OK for next screen.
Notice: If you fail to access to the web configuration, please go to “Trouble
Shooting” for detecting and solving your problem.
3.
Now, the Main Screen will pop up. Click Quick Start Wizard.
11
VigorIPPBX 3510 Quick Start Guide
Note: The home page will change slightly in accordance with the router you have.
4.
Enter the login password on the field of New Password and retype it on the field of
Confirm Password. Then click Next to continue.
5.
On the next page as shown below, please select the WAN interface (WAN 1 or
WAN2) that you use. If WAN1 interface is used, please choose WAN1; if WAN2
interface is used, please choose WAN2. Choose Auto negotiation as the physical
type for your router. Then click Next for next step.
VigorIPPBX 3510 Quick Start Guide
12
6.
On the next page as shown below, please select the appropriate Internet access type
according to the information from your ISP. For example, you should select PPPoE
mode if the ISP provides you PPPoE interface. Then click Next for next step.
PPPoE: if you click PPPoE or PPPoA as the protocol, please manually enter the
Username/Password provided by your ISP. Then click Next.
13
VigorIPPBX 3510 Quick Start Guide
PPTP/L2TP: if you click PPTP/L2TP, you will get the following page. Please type
in all the information originally provided by your ISP. Then click Next for next step.
Static IP: if you click Static IP, you will get the following page. Please type in the IP
address information originally provided by your ISP. Then click Next for next step.
VigorIPPBX 3510 Quick Start Guide
14
DHCP: if you click DHCP, you will get the following page. Simply click Next to
continue.
7.
Now you can see the following screen. It indicates that the setup is complete.
Different types of connection modes will have different summary. Click Finish and
then restart the router. Afterward, you will enjoy surfing on the Internet.
15
VigorIPPBX 3510 Quick Start Guide
This page is left blank.
VigorIPPBX 3510 Quick Start Guide
16
4. Trouble Shooting
This section will guide you to solve abnormal situations if you cannot access into the
Internet after installing the router and finishing the web configuration. Please follow
sections below to check your basic installation status stage by stage.
¾
Checking if the hardware status is OK or not.
¾
Checking if the network connection settings on your computer are OK or not.
¾
Pinging the router from your computer.
¾
Checking if the ISP settings are OK or not.
¾
Backing to factory default setting if necessary.
If all above stages are done and the router still cannot run normally, it is the time for you
to contact your dealer for advanced help.
4.1 Checking If the Hardware Status Is OK or Not
Follow the steps below to verify the hardware status.
1.
Check the power line and LAN cable connections. Refer to “2.1 Hardware
Installation” for details.
2.
Turn on the router. Make sure the PWR LED is on.
3.
Check if ACT LED blinks once per second and the correspondent LAN LED is
bright.
4.
If not, it means that there is something wrong with the hardware status. Simply back
to “2.1 Hardware Installation” to execute the hardware installation again. And
then, try again.
17
VigorIPPBX 3510 Quick Start Guide
4.2 Checking If the Network Connection Settings on Your
Computer Is OK or Not
Sometimes the link failure occurs due to the wrong network connection settings. After
trying the above section, if the link is stilled failed, please do the steps listed below to
make sure the network connection settings is OK.
For Windows
The example is based on Windows XP. As to the examples for other
operation systems, please refer to the similar steps or find support notes in
www.draytek.com.
1.
Go to Control Panel and then double-click on Network Connections.
2.
Right-click on Local Area Connection and click on Properties.
3.
Select Internet Protocol (TCP/IP) and then click Properties.
VigorIPPBX 3510 Quick Start Guide
18
4.
Select Obtain an IP address automatically and Obtain DNS server address
automatically.
For Mac OS
1.
Double click on the current used Mac OS on the desktop.
2.
Open the Application folder and get into Network.
3.
On the Network screen, select Using DHCP from the drop down list of Configure
IPv4.
19
VigorIPPBX 3510 Quick Start Guide
4.3 Pinging the Router from Your Computer
The default gateway IP address of the router is 192.168.1.1. For some reason, you might
need to use “ping” command to check the link status of the router. The most important
thing is that the computer will receive a reply from 192.168.1.1. If not, please check
the IP address of your computer. We suggest you setting the network connection as get IP
automatically. (Please refer to the section 4.2)
Please follow the steps below to ping the router correctly.
For Windows
1.
2.
Open the Command Prompt window (from Start menu> Run).
Type command (for Windows 95/98/ME) or cmd (for Windows NT/
2000/XP/Vista). The DOS command dialog will appear.
3.
Type ping 192.168.1.1 and press [Enter]. If the link is OK, the line of “Reply from
192.168.1.1:bytes=32 time<1ms TTL=255” will appear.
4.
If the line does not appear, please check the IP address setting of your computer.
For Mac OS (Terminal)
1.
Double click on the current used Mac OS on the desktop.
2.
Open the Application folder and get into Utilities.
3.
Double click Terminal. The Terminal window will appear.
4.
Type ping 192.168.1.1 and press [Enter]. If the link is OK, the line of “64 bytes
from 192.168.1.1: icmp_seq=0 ttl=255 time=xxxx ms” will appear.
VigorIPPBX 3510 Quick Start Guide
20
4.4 Checking If the ISP Settings are OK or Not
Open Internet Access page and then check whether the ISP settings are set correctly.
For PPPoE Users
1.
Check if the Enable option is selected.
2.
Check if Username and Password are entered with correct values that you got from
your ISP.
21
VigorIPPBX 3510 Quick Start Guide
For Static/Dynamic IP Users
1.
Check if the Enable option is selected.
2.
Check if Obtain an IP address automatically for Dynamic IP setting is selected.
Or check if IP address, Subnet Mask and Gateway are entered with correct values
for Static IP setting that you got from your ISP.
For PPTP/L2TP Users
1.
Check if the Enable option for PPTP/L2TP Link is selected.
2.
Check if Server, Username, Password and WAN IP address are set correctly
(must identify with the values from your ISP).
VigorIPPBX 3510 Quick Start Guide
22
4.5 Backing to Factory Default Setting If Necessary
Sometimes, a wrong connection can be improved by returning to the default settings. Try
to reset the router by software or hardware.
Warning: After pressing factory default setting, you will loose all settings
you did before. Make sure you have recorded all useful settings before you
pressing. The password of factory default is null.
Software Reset
You can reset the router to factory default via Web page.
Go to System Maintenance and choose Reboot System on the web page. The following
screen will appear. Choose Using factory default configuration and click OK. After few
seconds, the router will return all the settings to the factory settings.
Hardware Reset
While the router is running (ACT LED blinking), press the Factory Reset button and
hold for more than 5 seconds. When you see the ACT LED blinks rapidly, please release
the button. Then, the router will restart with the default configuration.
After restore the factory default setting, you can configure the settings for the router again
to fit your personal request.
23
VigorIPPBX 3510 Quick Start Guide
4.6 Contacting Your Dealer
If the router still cannot work correctly after trying many efforts, please contact your
dealer for further help right away. For any questions, please feel free to send e-mail to
support@draytek.com.
VigorIPPBX 3510 Quick Start Guide
24