Draytek Vigor2100VG Installation guide

Vigor 2100 Series Router
Quick Start Guide
Version: 2.0
Date: 2006/2/23
i
Copyright Information
Copyright
Declarations
Copyright 2006 All rights reserved. This publication contains information that is
protected by copyright. No part may be reproduced, transmitted, transcribed,
stored in a retrieval system, or translated into any language without written
permission from the copyright holders.
Trademarks
The following trademarks are used in this document:
z
Microsoft is a registered trademark of Microsoft Corp.
z
Windows, Windows 95, 98, Me, NT, 2000, XP and Explorer are
trademarks of Microsoft Corp.
z
Apple and Mac OS are registered trademarks of Apple Computer Inc.
z
Other products may be trademarks or registered trademarks of their
respective manufacturers.
Safety Instructions and Approval
Safety
Instructions
Warranty
z
z
Read the installation guide thoroughly before you set up the router.
The router is a complicated electronic unit that may be repaired only be
authorized and qualified personnel. Do not try to open or repair the router
yourself.
z
Do not place the router in a damp or humid place, e.g. a bathroom.
z
Do not stack the routers.
z
The router should be used in a sheltered area, within a temperature range
of +5 to +40 Celsius.
z
Do not expose the router to direct sunlight or other heat sources. The
housing and electronic components may be damaged by direct sunlight or
heat sources.
z
Do not deploy the cable for LAN connection outdoor to prevent electronic
shock hazards.
z
Keep the package out of reach of children.
z
When you want to dispose of the router, please follow local regulations on
conservation of the environment.
We warrant to the original end user (purchaser) that the router will be free from
any defects in workmanship or materials for a period of three (3) years from the
date of purchase from the dealer. Please keep your purchase receipt in a safe
place as it serves as proof of date of purchase. During the warranty period, and
upon proof of purchase, should the product have indications of failure due to
faulty workmanship and/or materials, we will, at our discretion, repair or replace
the defective products or components, without charge for either parts or labor, to
whatever extent we deem necessary tore-store the product to proper operating
condition. Any replacement will consist of a new or re-manufactured
functionally equivalent product of equal value, and will be offered solely at our
discretion. This warranty will not apply if the product is modified, misused,
tampered with, damaged by an act of God, or subjected to abnormal working
conditions. The warranty does not cover the bundled or licensed software of
other vendors. Defects which do not significantly affect the usability of the
product will not be covered by the warranty. We reserve the right to revise the
manual and online documentation and to make changes from time to time in the
contents hereof without obligation to notify any person of such revision or
changes.
Be a Registered
Owner
Web registration is preferred. You can register your Vigor router via
http://www.draytek.com. Alternatively, fill in the registration card and mail it to
the address found on the reverse side of the card.
Firmware & Tools
Updates
Due to the continuous evolution of DrayTek technology, all routers will be
regularly upgraded. Please consult the DrayTek web site for more information on
newest firmware, tools and documents.
http://www.draytek.com
i
European Community Declarations
Manufacturer:
Address:
Product:
DrayTek Corp.
No. 26, Fu Shing Road, HuKou County, HsinChu Industrial Park, Hsin-Chu, Taiwan 303
Vigor2100 series Routers
DrayTek Corp. declares that Vigor2100 series of routers are in compliance with the following essential
requirements and other relevant provisions of R&TTE Directive 1999/5/EEC.
The product conforms to the requirements of Electro-Magnetic Compatibility (EMC) Directive
89/336/EEC by complying with the requirements set forth in EN55022/Class B and EN55024/Class B.
The product conforms to the requirements of Low Voltage (LVD) Directive 73/23/EEC by complying with
the requirements set forth in EN60950.
The Vigor2100V/2100VG/2100G is designed for the WLAN 2.4GHz network throughput EC region,
Switzerland, and the restrictions of France.
Regulatory Information
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the use is encouraged to try to correct the interference
by one of the following measures:
z
Reorient or relocate the receiving antenna.
z
Increase the separation between the equipment and receiver.
z
Connect the equipment into an outlet on a circuit different form that to which the receiver is
connected.
z
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device may accept any interference received, including interference that may cause undesired
operation.
ii
Table of Contents
1. Introduction........................................................................................................... 1
1.1 Panel Explanation ...................................................................................................................... 2
1.1.1 Front and Rear View for Vigor2100V ............................................................................ 2
1.1.2 Front and Rear View for Vigor2100VG ......................................................................... 3
1.1.3 Front and Rear View for Vigor2100G............................................................................ 4
1.2 Package Content........................................................................................................................ 5
2. Installing Your Vigor2100 series Router ............................................................. 6
2.1 Hardware Installation.................................................................................................................. 6
3. Configuring Web Pages ....................................................................................... 7
3.1 Basic Configuration .................................................................................................................... 7
3.2 Wireless LAN Settings ............................................................................................................. 12
3.2.1 Basic Wireless LAN Concept ...................................................................................... 12
3.2.2 General Settings ......................................................................................................... 12
3.2.3 Security Settings ......................................................................................................... 13
4. Trouble Shooting ................................................................................................ 15
4.1 Checking If the Hardware Status Is OK or Not......................................................................... 15
4.2 Checking If the Network Connection Settings on Your Computer Is OK or Not ...................... 15
4.3 Pinging the Router from Your Computer .................................................................................. 18
4.4 Checking If the ISP Settings are OK or Not ............................................................................. 19
4.5 Backing to Factory Default Setting If Necessary...................................................................... 21
4.6 Contacting Your Dealer ............................................................................................................ 21
iii
1. Introduction
Equipped with VoIP phone ports, Vigor2100 broadband series router is an Internet access solution
for your LAN. It provides you shared web surfing and countless value-added features, such as
Firewall, Security, VoIP, and 802.11g Wireless LAN (up to 54Mbps for Vigor2100VG and
Vigor2100G only). These are all in a reliable one-box solution.
Vigor2100V and Vigor2100VG have a “Line” port on the rear panel for connecting to a PSTN
(regular analogue) line. The Loop Through option can be used to set an alternate telephone
number for your contact on the PSTN, which the Vigor2100V and Vigor2100VG will dial instead
of the SIP account if you lose ADSL access or power to the Vigor2100V and Vigor2100VG.
Hence, the PSTN line can act as a lifeline (backup mechanism) for VoIP calls. The lifeline
mechanism is activated automatically but can also be manually configured.
Characteristics
¾
Easy Internet-sharing of your broadband connection.
¾
Robust firewall to help protect your network from external attacks.
¾
Making regular phone calls over your broadband connection by simply plugging in your
phone.
¾
QoS-assured VoIP facilities to deliver superior quality.
¾
Automatic failover for your Public Switched Telephone Network (PSTN) during power cuts.
¾
802.11g Compliant Wireless LAN access with security features.
1
1.1 Panel Explanation
1.1.1 Front and Rear View for Vigor2100V
LED
Firewall
E-mail
Status
on
blinking
blinking
orange
WAN
green
blinking
VoIP
ACT (Activity)
green
orange
on
orange
LAN(1,2,3,4)
green
blinking
Interface
PWR
Line
Phone
WAN
P1 - P4
Factory Reset
Explanation
The firewall function is active.
When encountering DoS attacks.
When detecting one or more user-defined E-mails
existing on mail server.
A normal 10Mbps connection is through its
corresponding port.
A normal 100Mbps connection is through its
corresponding port.
Ethernet packets are transmitting.
Solid light when the handset of phone is picked up
(off hooked).
Blinking per 2 seconds when phone is connected
through VoIP.
Solid light when phone call is via PSTN life line.
The router is powered on and running properly.
A normal 10Mbps connection is through its
corresponding port.
A normal 100Mbps connection is through its
corresponding port.
Ethernet packets are transmitting.
Description
Connect the included power adapter to the power outlet.
Connect to the analog phone line for PSTN life line.
Connect to the analog phone for VoIP communication.
Connect the Cable/ADSL modem to access the Internet.
Connect to the local network devices.
Restore the default settings. Usage: Turn on the router (ACT LED is
blinking), press the hole and keep for more than 5 seconds. When
the ACT LED begins to blink rapidly, release the button. Then the
router will restart with the factory default configuration.
2
1.1.2 Front and Rear View for Vigor2100VG
LED
WLAN
E-mail
Status
on
blinking
blinking
orange
WAN
green
blinking
VoIP
ACT (Activity)
green
orange
on
orange
LAN(1,2,3,4)
green
blinking
Interface
PWR
Line
Phone
WAN
P1 - P4
Factory Reset
Explanation
The Wireless LAN function is active.
Data packets are transmitted over Wireless LAN.
When detecting one or more user-defined e-mails
existing on mail server.
A normal 10Mbps connection is through its
corresponding port.
A normal 100Mbps connection is through its
corresponding port.
Ethernet packets are transmitting.
Solid light when the handset of phone is picked up
(off hooked).
Blinking per 2 seconds when phone is connected
through VoIP.
Solid light when phone call is via PSTN life line.
The router is powered on and running properly.
A normal 10Mbps connection is through its
corresponding port.
A normal 100Mbps connection is through its
corresponding port.
Ethernet packets are transmitting.
Description
Connect the included power adapter to the power outlet.
Connect to the analog phone line for PSTN life line.
Connect to the analog phone for VoIP communication.
Connect the Cable/ADSL modem to access the Internet.
Connect to the local network devices.
Restore the default settings. Usage: Turn on the router (ACT LED is
blinking), press the hole and keep for more than 5 seconds. When
the ACT LED begins to blink rapidly, release the button. Then the
router will restart with the factory default configuration.
3
1.1.3 Front and Rear View for Vigor2100G
LED
WLAN
E-mail
Status
on
blinking
blinking
orange
WAN
green
Firewall
blinking
on
blinking
on
ACT (Activity)
orange
LAN(1,2,3,4)
green
blinking
Interface
PWR
WAN
P1 - P4
Factory Reset
Explanation
The Wireless LAN function is active.
Data packets are transmitted over Wireless LAN.
When detecting one or more user-defined e-mails
existing on mail server.
A normal 10Mbps connection is through its
corresponding port.
A normal 100Mbps connection is through its
corresponding port.
Ethernet packets are transmitting.
The firewall function is active.
When encountering DoS attacks.
The router is powered on and running properly.
A normal 10Mbps connection is through its
corresponding port.
A normal 100Mbps connection is through its
corresponding port.
Ethernet packets are transmitting.
Description
Connect the included power adapter to the power outlet.
Connect the Cable/ADSL modem to access the Internet.
Connect to the local network devices.
Restore the default settings. Usage: Turn on the router (ACT LED is
blinking), press the hole and keep for more than 5 seconds. When
the ACT LED begins to blink rapidly, release the button. Then the
router will restart with the factory default configuration.
4
1.2 Package Content
nQuick Start Guide
oCD
pAntenna for G models
qRJ-45 Cable (Ethernet)
rRJ-11 Cable ( for V / VG )
] The type of the power adapter depends on the country that the router will be installed:
UK-type power adapter
EU-type power adapter
USA/Taiwan-type power adapter
AU/NZ-type power adapter
5
2. Installing Your Vigor2100 series Router
This section will guide you to install the router through hardware connection and
configure the router’s settings through web browser.
2.1 Hardware Installation
Before starting to configure the router, you have to connect your devices correctly.
1.
Connect this device to a router with an Ethernet cable.
2.
Connect one port of 4-port switch to your computer with a RJ-45 cable. This device
allows you to connect 4 PCs directly.
3.
Connect one end of the power cord to the power port of this device. Connect the
other end to the wall outlet of electricity.
4.
Connect detachable antennas to the router for Vigor2100 series.
5.
For Vigor2100VG/V, connect Phone port to a conventional analog telephone, either
corded or wireless (DECT), with a RJ-11 cable.
6.
For Vigor2100VG/V, connect Line port to land line jack with a RJ-11 cable.
7.
Power on the router.
8.
Check the ACT and WAN, LAN LEDs to assure network connections.
(For the detailed information of LED status, please refer to section 1.1.)
6
3. Configuring Web Pages
3.1 Basic Configuration
The Quick Start Wizard is designed for you to easily set up your router for Internet
access. You can directly access the Quick Start Wizard via Web Configurator.
1.
Make sure your PC connects to the router correctly.
Notice: You may either simply set up your computer to get IP dynamically
from the router or set up the IP address of the computer to be the same
subnet as the default IP address of Vigor router 192.168.1.1. For the
detailed information, please refer to the later section - Trouble Shooting of
the guide.
2.
Open a web browser on your PC and type http://192.168.1.1. A pop-up window will
open to ask for username and password. Do not type any word on the window and
click OK for next screen.
3.
Now, the Main Screen will pop up. Click Quick Start Wizard.
7
Notice: Some of the settings might not appear as above, because the
home page will change slightly according to the features that your
router has.
4.
Enter the login password on the field of New Password and retype it on the field of
Retype New Password. Then click Next to continue.
5.
Select the appropriate time zone for your location. Then click Next to continue.
8
6.
On the next page as shown below, please select the appropriate Internet access type
according to the information from your ISP. For example, you should select PPPoE
mode if the ISP provides you PPPoE interface. Then click Next for next step.
PPPoE: if you click PPPoE as the protocol, please manually enter the
Username/Password provided by your ISP. Check the Always On means Internet
access is always on regardless of Internet usage. Then click Next.
9
PPTP: if you click PPTP, you will get the following page. Please type in all the
information originally provided by your ISP. Then click Next for next step.
Static IP: if you click Static IP, you will get the following page. Please type in the IP
address information originally provided by your ISP. Then click Next for next step.
10
DHCP: if you click DHCP, you will get the following page. Simply click Next to
continue.
7.
Now you can see the following screen. It indicates that the setup is complete.
Different types of connection modes will have different summary. Click Finish and
then restart the router. Afterward, you will enjoy surfing on the Internet.
11
3.2 Wireless LAN Settings
For operating Vigor2100 series well, it is necessary for you to set the wireless LAN
settings for using wireless function. Please read the following section carefully for
configuring the settings for this router.
(The default value of Frequency Domain was set by factory depends on the reselling
region.)
3.2.1 Basic Wireless LAN Concept
In an Infrastructure Mode of wireless network, Vigor wireless router plays a role as an
Access Point (AP) connecting to lots of wireless clients or Stations (STA). All the STAs
will share the same Internet connection with other wired hosts via Vigor wireless router.
3.2.2 General Settings
1.
Select Wireless LAN. On Detailed Settings group, click General Settings to open
the following page.
2.
Check the box Enable Wireless LAN to enable the wireless function.
3.
Select an appropriate wireless mode.
12
11g-only
The router can connect to IEEE802.11b and IEEE802.11g
stations simultaneously. This is default settings. Choose this
mode if you have no idea to change the mode.
The router can connect to IEE802.11g stations.
11b-only
The router can connect to IEE802.11b stations.
Mixed (11b+11g)
4.
Type in the name of the SSID and Channel. The default name for SSID is "default".
We suggest you change it to a particular name for your necessity.
SSID (service set
identifier)
It is used to name the wireless LAN for this router, and it must
have the same content in client PC/notebook wireless card(s).
SSID can be any text numbers or various special characters.
Channel
It is a wireless channel for the router. The default channel is 6.
You can change it to an appropriate one if the selected
channel is under serious interference.
3.2.3 Security Settings
1.
Select Wireless LAN. On Detailed Settings group, click Security to open the
following page.
2.
Select an appropriate encryption mode to improve the security and privacy of your
wireless data packets.
Disable
Turn off the encryption mechanism. For the security of
your router, please select any one of the encryption mode
here.
WEP Only
Accepts only WEP clients and the encryption key should be
entered in WEP Key.
WEP/802.1x Only
Accepts only WEP clients and the encryption key is
13
obtained dynamically through 802.1x.
WEP or WPA/PSK
Accepts WEP and WPA clients simultaneously and the
encryption key should be entered in WEP Key and PSK
respectively.
WEP/802.1x or
WPA/802.1x
Accepts WEP and WPA clients simultaneously and the
encryption key is obtained dynamically through 802.1x.
WPA/PSK Only
Accepts only WPA clients and the encryption key should be
entered in PSK.
WPA/802.1x Only
Accepts only WPA clients, and the encryption key is
obtained dynamically through 802.1x.
Note: You should also set RADIUS Server simultaneously if
WEP/802.1x or WPA/802.1x, WEP/802.1x Only or WPA/802.1x Only
mode is selected.
3.
For WPA encryption, type in 8~63 ASCII characters or 64 Hexadecimal digits
leading by 0x, for example "0123456789ABCD...." or "0x321253abcde....." on the
field of Pre-Shared Key (PSK). WPA encrypts each frame transmitted from the
radio using the Pre-Shared Key (PSK) which entered from this panel or a key got
dynamically through 802.1x.
4.
As to WEP encryption, select 64-bit or 128-bit as the encryption mode. For 64bits
WEP key, type in 5 ASCII characters or 10 hexadecimal digitals leading by 0x, for
example, ABCDE or 0x4142434445. And for 128bits WEP key, type in 13 ASCII
characters or 26 hexadecimal digits leading by 0x, for example, ABCDEFGHIJKLM
or 0x4142434445464748494A4B4C4D. There are four sets of WEP Keys that you
can type. Select any one of them as the WEP key.
5.
Note: 128 bits WEP is most secure, but has more encryption/decryption
overhead. Note that all wireless devices must support the same WEP
encryption bit size and have the same key. Four keys can be entered here,
but only one key can be selected at a time. The keys can be entered in
ASCII or Hexadecimal. Click the circle under Use next to the key you
wish to use.
Click OK to save settings.
14
4. Trouble Shooting
This section will guide you to solve abnormal situations if you cannot access into the
Internet after installing the router and finishing the web configuration. Please follow
sections below to check your basic installation status stage by stage.
¾
Checking if the hardware status is OK or not.
¾
Checking if the network connection settings on your computer are OK or not.
¾
Pinging the router from your computer.
¾
Checking if the ISP settings are OK or not.
¾
Backing to factory default setting if necessary.
If all above stages are done and the router still cannot run normally, it is the time for you
to contact your dealer for advanced help.
4.1 Checking If the Hardware Status Is OK or Not
Follow the steps below to verify the hardware status.
1.
Check the power line and WLAN/LAN cable connections.
Refer to “2.1 Hardware Installation” for details.
2.
Turn on the router. Make sure the ACT LED blink once per second and the
correspondent LAN LED is bright.
3.
If not, it means that there is something wrong with the hardware status. Simply back
to “2.1 Hardware Installation” to execute the hardware installation again. And
then, try again.
4.2 Checking If the Network Connection Settings on Your
Computer Is OK or Not
Sometimes the link failure occurs due to the wrong network connection settings. After
trying the above section, if the link is stilled failed, please do the steps listed below to
make sure the network connection settings is OK.
15
For Windows
Note: The example is based on Windows XP. As to the examples for other
operation systems, please refer to the similar steps or find support notes in
www.draytek.com.
1.
Go to Control Panel and then double-click on Network Connections.
2.
Right-click on Local Area Connection and click on Properties.
3.
Select Internet Protocol (TCP/IP) and then click Properties.
16
4.
Select Obtain an IP address automatically and Obtain DNS server address
automatically.
For MacOs
1.
Double click on the current used MacOs on the desktop.
2.
Open the Application folder and get into Network.
3.
On the Network screen, select Using DHCP from the drop down list of Configure
IPv4.
17
4.3 Pinging the Router from Your Computer
The default gateway IP address of the router is 192.168.1.1. For some reason, you might
need to use “ping” command to check the link status of the router. The most important
thing is that the computer will receive a reply from 192.168.1.1. If not, please check
the IP address of your computer. We suggest you setting the network connection as get IP
automatically. (Please refer to the section 4.2)
Please follow the steps below to ping the router correctly.
For Windows
1.
2.
Open the Command Prompt window (from Start menu> Run).
Type command (for Windows 95/98/ME) or cmd (for Windows NT/ 2000/XP). The
DOS command dialog will appear.
3.
Type ping 192.168.1.1 and press [Enter]. It the link is OK, the line of “Reply from
192.168.1.1:bytes=32 time<1ms TTL=255” will appear.
4.
If the line does not appear, please check the IP address setting of your computer.
For MacOs (Terminal)
1.
Double click on the current used MacOs on the desktop.
2.
Open the Application folder and get into Utilities.
3.
Double click Terminal. The Terminal window will appear.
4.
Type ping 192.168.1.1 and press [Enter]. It the link is OK, the line of “64 bytes
from 192.168.1.1: icmp_seq=0 ttl=255 time=xxxx ms” will appear.
18
4.4 Checking If the ISP Settings are OK or Not
Click Internet Access Setup group and then check whether the ISP settings are set
correctly.
For PPPoE Users
1.
Check if the Enable option is selected.
2.
Check if Username and Password are entered with correct values that you got from
your ISP.
19
For Static or Dynamic Users
1.
Check if the Enable option for Broadband Access is selected.
2.
Check if WAN IP Network Settings is set appropriately.
3.
Check if IP Address, Subnet Mask and Gateway are set correctly (must identify
with the values from your ISP) if you choose Specify an IP address.
For PPTP Users
1.
Check if the Enable option for PPTP Link is selected.
2.
Check if PPTP Server, Username, and Password are set correctly (must identify
with the values from your ISP).
3.
Check if LAN2/WAN IP Network Settings are set properly. If you select Specify
an IP address, you have to type in the values of IP Address and Subnet Mask
manually. Be sure the values that you type identify with the values from your ISP.
20
4.5 Backing to Factory Default Setting If Necessary
Sometimes, a wrong connection can be improved by returning to the default settings. Try
to reset the router by software or hardware.
Warning: After pressing factory default setting, you will loose all settings
you did before. Make sure you have recorded all useful settings before you
pressing. The password of factory default is null.
Software Reset
You can reset the router to factory default via Web page.
Go to System Management and choose Reboot System on the web page. The following
screen will appear. Choose Using factory default configuration and click OK. After few
seconds, the router will return all the settings to the factory settings.
Hardware Reset
While the router is running (ACT LED blinking), press the Factory Reset button and
hold for more than 5 seconds. When you see the ACT LED blinks rapidly, please release
the button. Then, the router will restart with the default configuration.
After restore the factory default setting, you can configure the settings for the router again
to fit your personal request.
4.6 Contacting Your Dealer
If the router still cannot work correctly after trying many efforts, please contact your
dealer for further help right away. For any questions, please feel free to send e-mail to
support@draytek.com.
21