SignaMax 065-1896SFPTB User`s guide

Signamax
 Connectivity Systems
Gigabit SFP
Converter Series
Model - 065-1896SFPTB
U
S
E
R
’
S
G
U
I
D
E
Signamax
 Connectivity Systems
Gigabit SFP
Converter Series
User’s Guide
Signamax
 Gigabit SFP Hardened Media Converter
FCC Warning
This equipment has been tested and found to comply with
the limits for a Class A digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the
equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with this user’s guide, may cause harmful
interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct
the interference at his or her own expense.
CE Mark Warning
This is a Class A product. In a domestic environment, this
product may cause radio interference in which case the user
may be required to take adequate measures.
Signamax Connectivity Systems from Advanced Electronic
Supports Products Inc. All rights reserved. All brand names
are registered trademarks of their relative holders.
Trademarks
Product names mentioned in this manual may be trademarks
or registered trademarks of those products and are hereby
acknowledged.
Ethernet is a trademark of Xerox Corporation.
Microsoft Windows is a trademark of Microsoft Corporation.
Signamax is a trademark of Advanced Electronic Support Products, Inc.
User’s Manual
1
Signamax
 Gigabit SFP Hardened Media Converter
Preface
Our hardened media converter provides an affordable
solution for rugged environments, transportation road-side
cabinets, industrial shop floors, multi tenant dwellings or
Fiber To The Home (FTTH) applications. Capable of
operating at temperature extremes of -40°F to +167°F (-40°C
to +75°C), this is by far the media converter of choice for
harsh environments in which space constraints exist.
Plug-and-Play Solution:
The hardened media converter is a plug-and-play compact
media converter which doesn't have any complicated
software to set up.
This manual describes the installation and use of the
hardened media converter with the Link Fault Signaling (LFS)
function. The converter also provides one channel media
conversion between 10/100/1000BaseT/TX and a Gigabit
SFP socket port.
The converter is in full compliance with IEEE802.3 10BaseT,
IEEE802.3u 100BaseTX, IEEE802.3ab 1000BaseT and
IEEE802.3z 1000BaseSX/LX standards.
In this manual, you will find:
2
Product overview
Features of the media converter
Illustrative LED functions
Installation instructions
Specifications
User’s Manual
Signamax
 Gigabit SFP Hardened Media Converter
Table of Contents
FCC Warning ................................................................................ 1
CE Mark Warning ........................................................................ 1
Trademarks.................................................................................... 1
Preface............................................................................................ 2
Table of Contents .......................................................................... 3
Introduction ................................................................................... 4
Product Overview ........................................................................ 4
Product Features ......................................................................... 4
One-Channel Media Converter.................................................... 7
Ports ............................................................................................ 7
Port Settings ................................................................................ 7
Front Panel & LEDs.................................................................... 8
Installation ..................................................................................... 9
Selecting a Site for the Equipment ............................................... 9
Wiring Diagram........................................................................... 9
DIN Rail Mounting .................................................................... 10
Connecting to Power ................................................................. 11
Specifications ............................................................................... 14
Contact Information.................................................................... 16
Contact Information.................................................................... 16
User’s Manual
3
Signamax
 Gigabit SFP Hardened Media Converter
Introduction
The media converter provides one channel for media
conversion between 10/100/1000BaseT/TX and a Gigabit
SFP socket port with the Link Fault Signaling (LFS) function.
This hardened fiber optic solution is perfectly suitable for
industrial applications or rugged environmental conditions.
Product Overview
Product Features
4
Meets NEMA TS1/TS2 environmental requirements such
as temperature, shock, and vibration for traffic control
equipment.
Meets EN61000-6-2 & EN61000-6-3 EMC Generic
Standard Immunity for industrial environment.
DIP switch configuration for link-fault-pass-through, fiber
auto/force mode, and port link down alarm.
4096 MAC addresses, 2.75M bits buffer memory.
Supports 802.3/802.3u/802.3ab/802.3z/802.3x. Autonegotiation and Auto MDI/MDIX.
SFP socket for Gigabit fiber optic expansion.
User’s Manual
Signamax
 Gigabit SFP Hardened Media Converter
The Gigabit SFP socket with SFP fiber transceiver should
be set to (forced full duplex mode, forced full duplex
mode) or (auto mode, auto mode) when two
10/100/1000BaseT/TX and Gigabit SFP socket onechannel media converters are connected to each other
via the Gigabit SFP socket with a SFP fiber transceiver.
Full wire-speed forwarding rate.
Back-pressure & IEEE802.3x compliant flow control.
Alarms for power and port link failure by relay output.
Relay contact rating with current 1A @ 30VDC, 0.5A @
120VAC.
Operating voltage and Max. current consumption: 1A @
12VDC, 0.5A @ 24VDC, 0.25A @ 48VDC. Power
consumption: 12W Max.
Power Supply: Redundant DC Terminal Block power
inputs or 12VDC DC JACK with 100-240VAC external
power supply.
Field Wiring Terminal Markings: Use Copper Conductors
Only, 140/167 ℉ (60/75 ℃ ), wire range 12-24 AWG,
torque value 7 lb-in.
-40℉ to 167℉ (-40℃ to 75℃) operating temperature
range. Tested for functional operation @ -40℉ to 185℉
(-40 ℃ to 85 ℃ ). UL508 Industrial Control Equipment
certified Maximum Surrounding Air Temperature @ 167
℉ (75℃).
For use in Pollution Degree 2 Environment.
Supports DIN-Rail, Panel, or Rack Mounting installation.
Front panel status LEDs.
<Note>
Both of the Gigabit SFP socket with SFP fiber transceiver
should be forced to full duplex mode (or auto mode) when
two 10/100/1000BaseT/TX and Gigabit SFP socket onechannel media converters are connected to each other via
the Gigabit SFP socket with a SFP fiber transceiver.
User’s Manual
5
Signamax
 Gigabit SFP Hardened Media Converter
Packing List
When you open this product package, you will find the items
listed below. Please inspect the contents, and report any
apparent damage or missing items immediately to our
authorized reseller.
The Media Converter
User’s Manual
AC to DC Power Adaptor and Power Cable (optional)
6
User’s Manual
Signamax
 Gigabit SFP Hardened Media Converter
One-Channel Media Converter
Ports
This Converter provides one copper port and one Gigabit
SFP socket port. The Gigabit SFP socket port is available for
options of Multi-mode, Single-mode, or WDM Single-mode
SFP fiber transceiver using LC connector.
The copper port uses RJ-45 connector, auto-MDIX, and auto
negotiates.
Port Settings
Port settings are made very simple by means of a DIP (Dual
Inline Package) switch on the front panel of the hardened
media converter.
Default DIP switch settings:
There are four pins on the DIP switch for port settings. Refer to
the table below for more details.
DIP
switch
0 (OFF)
1 (ON)
1
Disable LFS
Enable LFS
2
Disable link down alarm for Enable link down alarm for
copper port
copper port
3
Disable link down alarm for Enable link down alarm for SFP
SFP socket port
socket port
4
Enable force mode for SFP Enable auto-negotiation for SFP
socket port
socket port
User’s Manual
7
Signamax
 Gigabit SFP Hardened Media Converter
Front Panel & LEDs
The LED indicators give you instant feedback on converter
status:
LEDs
FAULT
Power1
Power2
State
Steady
Off
Steady
Off
Indication
Power redundant system or ports function abnormally
Power redundant system and ports function normally
Power on
Power off
Power3
LFS
Steady
Off
1000BaseSX/LX
LINK/ACT Steady
Flashing
LFS function enabled
LFS function disabled
A valid network connection established for SFP port
Transmitting or receiving data
ACT stands for Activity
Off
No valid network connection established for SFP port
10/100/1000BaseTX
LINK/ACT Steady A valid network connection established for copper port
Flashing Transmitting or receiving data
ACT stands for Activity
Off
No valid network connection established for copper
port
FDX/COL Steady Connected in full duplex mode
Flashing Collision occurred
COL stands for Collision
Off
Connected in half duplex mode
1000
Steady Connected at 1000Mbps
Off
Not connected at 1000Mbps
100
Steady Connected at 100Mbps
Off
Connected at 10Mbps
8
User’s Manual
Signamax
 Gigabit SFP Hardened Media Converter
Installation
This chapter gives step-by-step installation instructions for
the Converter.
Selecting a Site for the Equipment
As with any electric device, you should place the equipment
where it will not be subjected to extreme temperatures,
humidity, or electromagnetic interference. Specifically, the
site you select should meet the following requirements:
The ambient temperature should be between - 40 to 167
degrees Fahrenheit (- 40 to 75 degrees Celsius).
The relative humidity should be less than 95 percent,
non-condensing.
Surrounding electrical devices should not exceed the
electromagnetic field (RFC) standards.
Make sure that the equipment receives adequate ventilation.
Do not block the ventilation holes of the equipment.
The power outlet should be within 6 feet (1.8 meters) of the
product.
Wiring Diagram
Field Wiring Terminal Markings: Use Copper Conductors
Only, 140/167℉ (60/75℃), wire range 12-24 AWG, torque
value 7 lb-in.
User’s Manual
9
Signamax
 Gigabit SFP Hardened Media Converter
DIN Rail Mounting
•
•
•
10
Fix the DIN rail attachment plate to the back panel of the
media converter.
Installation: Place the media converter on the DIN rail
from above using the slot. Push the front of the media
converter toward the mounting surface until it audibly
snaps into place.
Removal: Pull out the lower edge and then remove the
media converter from the DIN rail.
User’s Manual
Signamax
 Gigabit SFP Hardened Media Converter
Connecting to Power
Redundant DC Terminal Block Power Inputs and 12VDC DC
Jack:
Redundant DC Terminal Block Power Inputs (preferred
connection)
There are two pairs of power inputs can be used to power up
this device.
User’s Manual
11
Signamax
 Gigabit SFP Hardened Media Converter
Step 1: Connect the DC power cord to the plug-able terminal
block on the media converter, and then plug it into a standard
DC outlet.
Step 2: Disconnect the power cord if you want to shut down the
media converter.
12VDC DC Jack (not supplied; available separately via special
order)
Step 1: Connect the AC to DC power adapter to the receptacle
on the topside of the media converter.
Step 2: Connect the power cord to the AC to DC power adapter
and attach the plug into a standard AC outlet with the
appropriate AC voltage.
Alarms for Power and Port Failure
Step 1: There are two pins on the terminal block that are used
for power failure detection. It provides a normal closed output
when the power source is active. Use this as a dry contact
application to send a signal for power failure detection.
Power Input Assignment
Power3
12VDC
+ 12-48VDC
Power2
- Power Ground
Power1
+
12-48VDC
-
Power Ground
DC Jack
Terminal Block
Earth Ground
Relay Alarm Assignment
*Relay warning signal disable for following:
The relay contact closes if Power1 and
FAULT Power2 are both failed but Power3 on.
The relay contact closes if Power3 is failed
but Power1 and Power2 are both on.
<Note>
The relay output is normal in an open position when there is no
power to the media converter. Please do not connect any
12
User’s Manual
Signamax
 Gigabit SFP Hardened Media Converter
power source to this terminal to prevent a short circuit to your
power supply.
User’s Manual
13
Signamax
 Gigabit SFP Hardened Media Converter
Specifications
Applicable Standards
Fixed Ports
Speed
10BaseT
100BaseTX
1000BaseT
1000BaseSX/LX
Forwarding rate
Cable
1000BaseT
1000BaseSX/LX
LED Indicators
Dimensions
Weight
Power
Operating Voltage & Max.
Current Consumption
Power Consumption
Operating Temperature
Storage Temperature
Humidity
Safety
EMI
14
IEEE 802.3 10BaseT
IEEE 802.3u 100BaseTX
IEEE 802.3ab 1000BaseT
IEEE 802.3z 1000BaseSX/LX
1 copper port, 1 Gigabit SFP socket port
10/20Mbps for half/full-duplex
100/200Mbps for half/full-duplex
2000Mbps for full-duplex
2000Mbps for full-duplex
14,880pps for 10Mbps
148,810pps for 100Mbps
1,488,100pps for 1000Mbps
4-pair UTP/STP Cat. 5 up to 328ft. (100m)
MMF (50 or 62.5µm), SMF (9 or 10µm)
Per Unit:
FAULT, Power1, Power2, Power3, LFS
Per Port:
SFP socket: LINK/ACT
Copper: LINK/ACT, FDX/COL, 1000, 100
1.97” (W) x 4.33” (D) x 5.31” (H)
(50mm (W) × 110mm (D) x 135mm (H))
1.76lbs. (0.8Kg)
DC Jack: 12VDC, External AC/DC
required
Terminal Block: 12-48VDC
1A @ 12VDC, 0.5A @ 24VDC, 0.25A @
48VDC
12W Max.
-40℉ ~ 167℉ (-40°C ~ 75°C)
Tested for functional operation @
-40℉ ~ 185℉ (-40°C ~ 85°C)
UL508 Industrial Control Equipment
certified
Maximum
Surrounding
Air
Temperature @ 167℉ (75 )
-40℉ ~ 185℉ (-40°C ~ 85°C)
5 ~ 95%, non-condensing
UL508
FCC Part 15, Class A
VCCI, Class A
EN61000-6-3: EN55022, EN61000-3-2,
EN61000-3-3
User’s Manual
Signamax
 Gigabit SFP Hardened Media Converter
EMS
EN61000-6-2:
EN61000-4-2 (ESD Standard)
EN61000-4-3 (Radiated RFI Standards)
EN61000-4-4 (Burst Standards)
EN61000-4-5 (Surge Standards)
EN61000-4-6 (Induced RFI Standards)
EN61000-4-8 (Magnetic Field Standards)
Environmental
Test IEC60068-2-6 Fc (Vibration Resistance)
Compliance
IEC60068-2-27 Ea (Shock)
IEC60068-2-32 Ed (Free Fall)
NEMA TS1/2 Environmental requirements for traffic control equipment
User’s Manual
15
Signamax
 Gigabit SFP Hardened Media Converter
Contact Information
SIGNAMAX CONNECTIVITY SYSTEMS
An AESP Company
16295 N.W. 13h Avenue
Miami, Florida 33169, U.S.A.
Phone: 305-944-7710 Fax: 305-652-8489
Sales: 800-446-2377 Tech. Support: 800-4462377, ext. 201
Http://www.signamax.com
E-mail: info@signamax.com
16
User’s Manual