Mytee 1000DX-200 User manual

Instructions for
1000DX-200,1001DX-200,
1003DX, 1005DX Speedster
®
Please read before use.
Register your product
at http://www.mytee.
com/support/register
Model #
1000DX-200 p.3
1001DX-200 p.9
1003DX p.15
1005DX p.21
General information p.27
Serial #
Form # ADP-Speedster
5-14
1
2
1000DX-200 SPEEDSTER
1000DX-200 SPEEDSTER® FRONT
1000DX-200 SPEEDSTER® BACK
11
10
1
2
12
9
3
8
13
4
7
14
5
6
1. Switch plate
2. Easy faucet fill
3. Solution tank lid
4. Front handle
5. Front vent
16
6. 5” locking casters
7. Solution tank
8. Female quick disconnect
9. 2” Male Cuff-Lynx™
10. Recovery lid
11. Recovery tank
12. Push handle
13. Drain valve
14. Power cord
15. Back vent
1000DX-200 SPEEDSTER® ITEMS INCLUDED
H110 Cuff-Lynx™
2” Hose Adapter
H375 - Hose Hanger
(4) screws
15
16. 12” Rear wheels
1000DX-200 SPEEDSTER® CORD
H141 Cuff-Lynx™
2” Hose Reducer to 1.5”
Plug the power cord into a single, 20A grounded wall outlet.
H226 Drain Elbow
3
1000DX-200 SPEEDSTER
1000DX-200 SPEEDSTER® VAC/SOL
HOSE CONNECTIONS
1000DX-200 SPEEDSTER® SWITCHES
Attach one end of a solution hose to a wand or other tool,
the other end to the Speedster’s® front quick disconnect.
Attach one end of a vacuum hose to the tool, the other end
to the Speedster’s® Cuff-Lynx™ vacuum hose port.
Turn on Vac 1, Vac 2 and Pump switches.
1000DX-200 SPEEDSTER® FILL SOLUTION TANK
1000DX-200 SPEEDSTER® FLOAT SWITCH
The Speedster® is equipped with an electronic float switch
inside the recovery tank. The recovery float switch is activated by rising water to prevent suction into the vacuum
stacks damaging the motors.
Lift lid and manually fill the solution tank or use the easy
faucet fill.
4
1000DX-200 SPEEDSTER
1000DX-200 SPEEDSTER® DUMP VALVE
1000DX-200 SPEEDSTER®
FILTER MAINTENANCE
VACUUM
STACK
FILTER
INTAKE
FILTER
Attach the 45˚ drain elbow to the drain spout in back. Lift up
the dump valve and empty the tank.
Check and clean the vacuum stack filters and solution
tank filter daily by twisting off, rinsing with clean water and
replacing.
1000DX-200 SPEEDSTER®
LOCKING CASTERS
MYTEE® SYSTEM MAINTAINER
Locking casters help keep the machine remain stationary
during use.
Weekly flushing of the solution system with Mytee® System
Maintainer helps keep lines clean and prevents chemical
build-up, improving pump life, performance and pressure.
5
Order parts at: www.mytee.com/products/product.php?id=1000DX
6
A
B
C
D
E
F
H343
H296
2
3
G018
P732
H768
B107
H484
H256
B142
B135
B102
B656
43
44
45
46
47
48
49
50
51
52
Part prices are subject to change.
8
H485
H178
42
55
H215
41
B109
H213
40
PH634-36
PH628-24
39
54
H217
38
53
H194
37
H770
32
H124
H912
31
H211
B172
30
36
C322D
29
35
H222
28
G052
H299
27
34
B105
H307
B136
25
26
33
AH120
24
17
B186
E550
16
23
H220
15
B160
H221
14
22
H219
13
H347
H251
12
PH615-26
H254
11
21
H371
10
20
H666
9
P731
H342
8
H202
H210
7
19
H216
6
18
E370
H273
5
H186
C317
4
PART NO.
1
8
ITEM
NO.
7
handle, breeze and dx
sol hose, 1/4", silicone braided, clear
adapter, brass, 1/4" barb x 1/4" mpt
ball valve, 1/4''
qd, brass, 1/4" f
tee, brass, 1/4" mpt
coupling, brass, 1/4" fpt x 1/4" fpt
screw, 10-32 x 3/4" phil pan head, zinc
plate, mounting, QD
nipple, brass, 1/4"m, hex
bolt, 1/4-20 x 3/4" serrated hex flange, zinc
sol tank, speedster
cover, sol tank (sp)
faucet fill
nut, hex, 1/4-20 s/s
washer, 1/4" lock, s/s
vac hose, 2", wire reinforced
clamp, hose, 2-1/4 dia
coupler, 2" dia x 2.5" length, s/s
Cuff-Lynx, 2" mpt x 2" female cuff
washer, 1/4"id x 1"od, flat, s/s
washer, buna 1-1/8" od x 3/16" id
washer, star, 1/4" steel zinc
bolt, 1/4-20 x 1/2" serrated hex flange, zinc
bracket, rear, fb/spy
elbow, brass, 90 deg, 1/2" barb x 3/8"mpt
pump, 220psi, diaphragm,115V
screw, 10-32 x 1-1/4" phil pan head, s/s
washer, 11/16"id x 1-1/2"od x .075, s/s
bushing, brass, 3/8"mpt x 1/4"
elbow, brass, 90 deg, 1/4" mpt x 1/4" mpt
sol hose, 28" x 1/4", 1/4 fpt
elbow, brass, 90 deg, 3/8"mpt x 3/8" fmpt
adapter, brass, 1/2" barb x 3/8" fsw, ball end
clamp, hose, 5/16-29/32
sol hose, 1/2" kuri 100psi
bolt, 1/4-20 x 3/4" hex head, s/s
base, speedster
power cord, pigtail, 30", 12/3, black
fitting, strain relief, cord
nut, lock, 1/2" steel
cap, axle, 1/2"
wheel, 12"
washer, axle, cut 1/2" id
axle, 18.25" x .50" dia
caster, 5", Black hub & gray tread
bolt, 1/4-20 x 1" hex head, s/s
washer, 1/4" flat, s/s
nut, lock, 1/4-20, nylon insert, s/s
nut, kep, #10-32 zinc
controller, water level, dual pump or vac
screw, 10-32 x 3/4, phil flat full thread
guard, cooling fan, wire
screw, #10 x 5/8" hex head, zinc
fan, cooling, 115V
DESCRIPTION
7
1
1
1
1
1
1
1
4
1
3
2
1
1
1
2
10
1
4
2
2
6
6
2
4
1
1
1
4
4
1
1
1
1
1
4
1
6
1
1
1
1
2
2
4
1
2
8
22
10
8
1
2
3
12
1
QTY.
6
$6.99 ea
$6.49 ft
$1.99 ea
$13.49 ea
$17.99 ea
$5.49 ea
$4.49 ea
$0.99 ea
$4.99 ea
$3.19 ea
$0.99 ea
$141.99 ea
$12.99 ea
$10.99 ea
$0.99 ea
$0.99 ea
$8.99/ft
$1.49 ea
$10.00 ea
$3.99 ea
$0.99 ea
$1.99 ea
$0.99 ea
$0.99 ea
$9.99 ea
$9.49 ea
$208.99 ea
$0.99 ea
$0.99 ea
$3.19 ea
$4.99 ea
$35.49 ea
$8.99 ea
$3.49 ea
$1.99 ea
$8.99/ft
$0.99 ea
$141.99 ea
$11.49 ea
$3.19 ea
$1.99 ea
$0.99 ea
$41.99 ea
$0.99 ea
$9.99 ea
$23.19 ea
$0.99 ea
$0.99 ea
$0.99 ea
$0.99 ea
$94.99 ea
$0.99 ea
$2.99 ea
$0.99 ea
$21.49 ea
MSRP
6
G097
G022
PH633-1
P503
P520
G090
67
68
69
70
71
72
H212
E373
83
84
85
G004
91
92
Cuff-Lynx, 2" hose x 2" fem swivel Cuff-Lynx
power cord, ext 50', 12/3 black
H110
E530
4
Cuff-Lynx, 2" x 1.5" reducer
5
screw, 10-32 x 1/2" phil pan head, s/s
H141
hanger, wire formed, hose
gasket, strip, 3/4" x 36" x 1/8"
piglet filter
DESCRIPTION
gasket, vac motor - Speedster
vac motor, 3 stage, low amp
vac support, 3 stage, 3.25", no thrds
bolt, hex, 1/4-20 x 4", zinc Finish
plastite screw, 1/4 x 1"
bracket, "L"
elbow, brass, 90 deg, 1/4" fpt x 1/4" fpt
level switch, vacuum shut-off, rear threads
H230
H375
G085
G008
PART NO.
nut, 1/4" npt
plate, switch, 1000DX-200
Washer, #8, flat regular
screw, 10-32 x 1/2" SHCS, alloy
plug
switch, rocker, 2 position
Cuff-Lynx, 2" m cuff x 2" mpt
gasket, 2" inlet
elbow, inlet assembly 2"
gasket, 7", vac lid
screw, #8 x 5/8 phil oval, s/s
lid, vac tank, clear, 7"
adapter, pvc, 1-1/2" mpt x 1-1/2" fms
adapter, 1.5" pvc, 45 deg, fslip x fslip
pipe, pvc, 1-1/2"
filter, foam, 2-3/8" x 1"
screen, mesh filter, 1-1/2" dia
adapter, 1.5" pvc, fslip x fslip
pipe, pvc, 1-1/2"
pipe, pvc, 1-1/2"
nut, lock, 1-1/2", steel
vac tank, speedster
valve, drain, 1-1/2"
spout, drain, 45 degree
nipple, brass, 3/8" x close
bushing, brass, 1/2"mpt x 3/8" fpt, hex
filter, strainer, 1/2"
bracket, front hinge, sp/fb
DESCRIPTION
4
flat washer, 9/16"ID x 1 1/16"OD, AN960-C916
ITEMS NOT SHOWN
H503
C302LA
90
H096
B156
82
89
H348
81
H034
H612
80
88
H389
79
B207
P967A
78
H390A
E515
77
87
H135
76
86
A926
G083
75
H304
P502
66
G091
PH633-4
65
74
PH633-03
64
73
P733
H314
63
H225
62
H226
61
B210
58
60
B119A
57
B216
H378
59
PART NO.
56
5
ITEM
NO.
1
1
1
2
1
1
1
QTY
2
2
6
6
4
2
1
1
1
1
1
3
3
1
3
1
1
1
1
6
1
2
4
2
2
2
2
2
4
2
1
1
1
1
1
1
1
QTY.
3
$74.99 ea
$3.99 ea
$3.99 ea
$0.99 ea
$10.99 ea
$4.99 ea
$6.29 pak
MSRP
$8.99 ea
$139.99 ea
$3.99 ea
$0.99 ea
$2.99 ea
$6.99 ea
$5.99 ea
$13.99 ea
$0.99 ea
$1.99 ea
$6.99 ea
$0.99 ea
$0.99 ea
$1.99 ea
$13.99 ea
$3.99 ea
$2.49 ea
$15.99 ea
$11.99 ea
$0.99 ea
$36.99 ea
$2.99 ea
$3.29 ea
$4.99 ft
$2.99 ea
$4.99 ea
$5.00 ea
$4.99/ft
$4.99/ft
$1.99 ea
$190.99 ea
$20.99 ea
$3.19 ea
$1.99 ea
$2.49 ea
$6.49 ea
$8.99 ea
MSRP
3
NAME
M. LaBarbera
DATE
10/2013
2
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
MYTEE PRODUCTS, INC. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
MYTEE PRODUCTS, INC. IS
PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
COMMENTS:
CHECKED
DRAWN
2
SCALE: 1:48
1
DO NOT
SCALE DRAWING
C
SHEET 1 OF 3
C 1000DX-200
SIZE DWG. NO.
REV
PRODUCTS, INC.
858-679-1191
speedster
mytee
TITLE:
1
A
B
C
D
E
F
1000DX-200 SPEEDSTER PARTS & PRICING
7
A
B
C
D
E
F
8
14
17
8
13
16
15
59
to sol tank
filter thru
B216
12
11
21
22
18
23
24
10
7
20
26
27
25
7
9
28
8
7
6
8
6
29
4
1
3
6
2
37
38
19
37
34
35
40
31
42
19
43
5
23
34
32
to pump
"IN"
thru B186
35
33
32
5
41
7
44
45
35
55
34
20
46
47
48
49
27
59
58
57
8
56
19
8
4
40
46
53
24
to pump
"OUT"
thru AH120
54
52
50
51
3
64
60
63
64
65
66
67
3
46
4
68
36
5
to female qd
thru B107
30
6
61
69
89
40
8
90
91
92
62
70
DATE
10/2013
NAME
46
75
73
M.LaBarbera
88
87
85
86
82
72
2
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
MYTEE PRODUCTS, INC. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
MYTEE PRODUCTS, INC. IS
PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
COMMENTS:
CHECKED
DRAWN
71
70
2
76
80
SCALE: 1:48
1
DO NOT
SCALE DRAWING
C
SHEET 2 OF 3
C 1000DX-200
SIZE DWG. NO.
REV
PRODUCTS, INC.
858-679-1191
79
78
77
speedster
mytee
83
TITLE:
84
80 81
6
74
1
A
B
C
D
E
F
1000DX-200 SPEEDSTER PARTS & PRICING
G
8
1/24/2014
Ground to
Metal Plate
L2
L1
115V
Float
Switch
#E-370
relays
N/O
L2
L1
L2
L1
L1
L2
Pump
C-322D
G
VAC 2
C-302LA
G
VAC 1
C-302LA
G
Cooling
Fan
C-317
1000DX-200
115 Volt System
E-515
E-515
E-515
1000DX-200 SPEEDSTER WIRING SCHEMATIC
1001DX-200 SPEEDSTER
1001DX-200 SPEEDSTER® FRONT
1001DX-200 SPEEDSTER® BACK
1
2
12
11
10
9
3
8
13
4
7
14
5
16
6
1. Switch plate
2. Easy faucet fill
3. Solution tank lid
4. Front handle
5. Front vent
6. 5” locking casters
7. Solution tank
8. Female quick disconnect
9. 2” Male Cuff-Lynx™
10. Recovery lid
11. Recovery tank
12. Push handle
13. Drain valve
14. Dual power cords
15. Back vent
1001DX-200 SPEEDSTER® ITEMS INCLUDED
15
16. 12” Rear wheels
1001DX-200 SPEEDSTER® CORDS
Left cord: Powers Vac 2 & Heater 2.
Right cord: Powers Vac 1, Heater 1 & Pump.
Yellow tag
indicates primary
cord.
H110 Cuff-Lynx™
2” Hose Adapter
H375 - Hose Hanger
(4) screws
H141 Cuff-Lynx™
2” Hose Reducer to 1.5”
Plug each power cord into a separate, 20A grounded wall
outlet. Outlets must be on two separate breakers. When
the amber light on the switch plate illuminates, the machine
is on separate circuits (not necessarily 20A circuits). You
can identify the primary cord by the yellow tag.
H226 Drain Elbow
9
1001DX-200 SPEEDSTER
1001DX-200 SPEEDSTER® VAC/SOL
HOSE CONNECTIONS
1001DX-200 SPEEDSTER® SWITCHES
Attach one end of a solution hose to a wand or other tool,
the other end to the Speedster’s® front quick disconnect.
Attach one end of a vacuum hose to the tool, the other end
to the Speedster’s® Cuff-Lynx™ vacuum hose port.
“On” switches are located on the plate in front of the machine. To use vacuums, turn on Vac 1 and Vac 2 switches.
To use pump, turn on Pump switch. To activate heat, turn
on Heater switch. Heater 1 for 1000 watts of heat. Heater
2 for 2000 watts of heat.
1001DX-200 SPEEDSTER®
FILL SOLUTION TANK
1001DX-200 SPEEDSTER®
FILTER MAINTENANCE
VACUUM
STACK
FILTER
INTAKE
FILTER
Lift lid and manually fill the solution tank or use the easy
faucet fill.
Check and clean the vacuum stack filters and solution
tank filter daily by twisting off, rinsing with clean water and
replacing.
10
1001DX-200 SPEEDSTER
1001DX-200 SPEEDSTER® FLOAT SWITCH
1001DX-200 SPEEDSTER® DUMP VALVE
The Speedster® is equipped with an electronic float switch
inside the recovery tank. The recovery float switch is activated by rising water to prevent suction into the vacuum
stacks damaging the motors.
Attach the 45˚ drain elbow to the drain spout in back. Lift
up the dump valve and empty the tank.
1001DX-200 SPEEDSTER®
LOCKING CASTERS
MYTEE® SYSTEM MAINTAINER
Locking casters help keep the machine remain stationary
during use.
Weekly flushing of the solution system with Mytee® System
Maintainer helps keep lines clean and prevents chemical
build-up, improving pump life, performance and pressure.
11
Order parts at: www.mytee.com/products/product.php?id=1001DX
12
A
B
C
D
E
F
Part prices are subject to change.
C317
H343
H296
H186
E370
H273
H216
H210
H342
H666
P731
H371
H254
H251
H219
AH105
AH156
B103
H256
H528
E519
B142
B108
H274
H903A
E573
E574
AH120
H221
H220
E550
PH615-26
B160
B186
B136
B105
H299
H222
C322D
B172
B173
H912
H770
H307
G052
H211
H203
H124
H194
H217
PH628-15
H213
H215
G018
PH612-36
H178
P732
H768
B107
H484
B135
B102
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
8
PART NO.
1
8
ITEM
NO.
7
tee, brass, 1/4" mpt
qd, brass, 1/4" f x 1/4" fpt
nipple, brass, 1/4"m, hex
plate, mounting, QD
faucet fill
sol tank, speedster
bolt, 1/4-20 x 3/4" serrated hex flange, zinc
vac hose, 2", wire reinforced
washer, 1/4" lock, s/s
nut, hex, 1/4-20 s/s
cover, sol tank (sp)
clear tubing, 1/2" OD x 3/8" ID, faucet fill
washer, star, 1/4" steel zinc
washer, buna 1-1/8" od x 3/16" id
washer, 1/4"id x 1"od, flat, s/s
bolt, 1/4-20 x 1-1/4"
Cuff-Lynx, 2" mpt x 2" female cuff
coupler, 2" dia x 2.5" length, s/s
clamp, hose, 2-1/4 dia
ferrule, 1/2", brass
bracket, rear, fb/spy
bolt, 1/4-20 x 1/2" serrated hex flange, zinc
washer, 11/16"id x 1-1/2"od x .075, s/s
screw, 10-32 x 1-1/4" phil pan head, s/s
pump, 220psi, diaphragm,115V
elbow, brass, 90 deg, 1/2" barb x 3/8"mpt
nut, lock, 1/2" steel
fitting, strain relief, cord
power cord, pigtail, 30", 12/3, black
sol hose, 1/2" kuri 100psi
adapter, brass, 1/2" barb x 3/8" fsw, ball end
elbow, brass, 90 deg, 3/8"mpt x 3/8" fmpt
elbow, brass, 90 deg, 1/4" mpt x 1/4" mpt
bushing, brass, 3/8"mpt x 1/4"
Thermostat, 200°, Auto, 1/4"
Thermostat, 310°F ± 10°F, Manual, 1/4"
sol hose, 28" x 1/4", 1/4 fpt
valve, brass, 1/4" check
screw, 6 x 3/16, phil pan head, self-tapping
heater, aluminum cast, single
wheel, 12"
cap, axle, 1/2"
hose, pulse, 3/8" x 17-1/2", (OAL), f
hose, 3/8", (OAL), f x fs, 5400 gray
elbow, brass, 90 deg, 1/4"mpt x 1/4" fpt
screw, 10-32 x 3/4" phil pan head, zinc
bracket, heater mounting, dual
heating rod, 1000W, 115V
coupling, brass, 1/4" fpt x 1/4" fpt
axle, 18.03" x .50" dia
washer, axle, cut 1/2" id
bolt, 1/4-20 x 1" hex head, s/s
caster, 5", Black hub & gray tread
base, speedster
washer, 1/4" flat, s/s
screw, #10 x 5/8" hex head, zinc
guard, cooling fan, wire
screw, 10-32 x 3/4, phil flat full thread
controller, water level, dual pump or vac
nut, kep, #10-32 zinc
nut, lock, 1/4-20, nylon insert, s/s
fan, cooling, 115V
DESCRIPTION
7
1
1
3
1
1
1
2
2
10
2
1
1
2
6
6
2
2
2
4
2
1
8
4
4
1
1
2
2
2
1
1
1
1
1
2
2
2
1
10
2
2
2
1
1
2
6
1
2
2
1
4
8
2
1
22
12
3
2
1
10
10
1
QTY.
6
$5.49 ea
$17.99 ea
$3.19 ea
$4.99 ea
$10.99 ea
$141.99 ea
$0.99 ea
$8.99/ft
$0.99 ea
$0.99 ea
$12.99 ea
$1.99/ft
$0.99 ea
$1.99 ea
$0.99 ea
$0.99 ea
$3.99 ea
$10.00 ea
$1.49 ea
$0.99 ea
$9.99 ea
$0.99 ea
$0.99 ea
$0.99 ea
$208.99 ea
$9.49 ea
$1.99 ea
$3.19 ea
$11.49 ea
$8.99/ft
$3.49 ea
$8.99 ea
$4.99 ea
$3.19 ea
$16.49 ea
$17.99 ea
$35.49 ea
$13.99 ea
$0.99 ea
$78.99 ea
$41.99 ea
$0.99 ea
$31.99 ea
$23.99 ea
$4.49 ea
$0.99 ea
$29.99 ea
$51.99 ea
$4.49 ea
$9.99 ea
$0.99 ea
$0.99 ea
$23.19 ea
$141.99 ea
$0.99 ea
$0.99 ea
$2.99 ea
$0.99 ea
$94.99 ea
$0.99 ea
$0.99 ea
$21.49 ea
MSRP
6
H485
H201
H378
67
68
69
H225
P733
A926
PH633-4
PH633-03
PH633-06
P502
G097
G022
PH633-1
G091
G090
H304
P503
P520
H314
G083
H135
E511
E516
E515
E512B
H389
H612
H348
B156
H212
E373
B207
H390A
H096
H503
C302LA
G004
E564
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
DESCRIPTION
hanger, wire formed, hose
H375
Cuff-Lynx, 2" hose x 2" fem swivel Cuff-Lynx
power cord, ext 50', 12/3 black
H110
E530
5
Cuff-Lynx, 2" x 1.5" reducer
H141
screw, 10-32 x 1/2" phil pan head, s/s
gasket, strip, 3/4" x 36" x 1/8"
G085
piglet filter
controller, circuit light
4
2
1
1
2
1
1
1
QTY
bracket, "L"
bolt, hex, 1/4-20 x 4", zinc Finish
vac support, 3 stage, 3.25", no thrds
vac motor, 3 stage, low amp
gasket, vacuum motor
flat washer, 9/16"ID x 1 1/16"OD
level switch, vacuum shut-off, rear threads
elbow, brass, 90 deg, 1/4" fpt x 1/4" fpt
plate, switch, 1000DX-200
nut, 1/4" npt
light, red, 250v
switch, rocker, 3 position
switch, rocker, 2 position
light, indicator, 125v (amber)
screw, 10-32 x 1/2" SHCS, alloy
Washer, #8, flat regular
nut, lock, 1-1/2", steel
gasket, 2" inlet
Cuff-Lynx, 2" m cuff x 2" mpt
lid, vac tank, clear, 7"
screw, #8 x 5/8 phil oval, s/s
adapter, 1.5" pvc, 45 deg, fslip x fslip
adapter, pvc, 1-1/2" mpt x 1-1/2" fms
screen, mesh filter, 1-1/2" dia
filter, foam, 2-3/8" x 1"
pipe, pvc, 1-1/2"
gasket, 7", vac lid
PIPE, 1-1/2" x 6" PVC
adapter, 1.5" pvc, fslip x fslip
valve, drain, 1-1/2"
vac tank, speedster
elbow, inlet assembly 2"
pipe, pvc, 1-1/2"
pipe, pvc, 1-1/2"
filter, strainer, 1/2"
bushing, brass, 1/2"mpt x 3/8" fpt, hex
nipple, brass, 3/8" x close
spout, drain, 45 degree
bolt, 1/4x1-1/2", hex head zinc
handle, breeze and dx
bolt, 1/4-20 x 1/2", hex head, zinc
bracket, front hinge, sp/fb
ferrule, 1/4" brass
sol hose, 1/4", silicone braided, clear
DESCRIPTION
H230
4
ball valve, 1/4''
adapter, brass, 1/4" barb x 1/4" mpt
G008
5
PART NO.
ITEMS NOT SHOWN
B119A
B210
B216
H226
71
72
73
74
H316
B170
PH634-20
65
66
70
B656
B109
PART NO.
63
64
ITEM
NO.
MSRP
$74.99 ea
$3.99 ea
$3.99 ea
$0.99 ea
$10.99 ea
$4.99 ea
$6.29 pak
1
2
6
6
2
2
2
1
1
1
1
2
1
3
1
4
3
2
1
1
1
6
4
2
2
2
2
1
2
2
1
1
1
2
2
1
1
1
1
2
1
2
1
2
1
1
1
QTY.
MSRP
$62.99 ea
$6.99 ea
$0.99 ea
$3.99 ea
$139.99 ea
$8.99 ea
$0.99 ea
$13.99 ea
$5.99 ea
$6.99 ea
$1.99 ea
$5.99 ea
$14.99 ea
$13.99 ea
$9.99 ea
$0.99 ea
$0.99 ea
$1.99 ea
$2.49 ea
$3.99 ea
$36.99 ea
$0.99 ea
$3.29 ea
$2.99 ea
$4.99 ea
$2.99 ea
$4.99 ft
$11.99 ea
$4.99 ft
$5.00 ea
$20.99 ea
$190.99 ea
$15.99 ea
$4.99/ft
$4.99/ft
$6.49 ea
$2.49 ea
$1.99 ea
$3.19 ea
$0.99 ea
$6.99 ea
$0.99 ea
$8.99 ea
$0.99 ea
$6.49 ft
$13.49 ea
$1.99 ea
3
3
NAME
M. LaBarbera
DATE
10/2013
2
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
MYTEE PRODUCTS, INC. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
MYTEE PRODUCTS, INC. IS
PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
CHECKED
DRAWN
2
SCALE: 1:48
1
DO NOT
SCALE DRAWING
C
SHEET 1 OF 3
C 1001DX-200
SIZE DWG. NO.
REV
PRODUCTS, INC.
858-679-1191
speedster
mytee
TITLE:
1
A
B
C
D
E
F
1001DX-200 SPEEDSTER PARTS & PRICING
13
A
B
C
D
E
F
20
21
24
24
26
19
25
27
8
23
6
22
8
59
to female
QD thru
B107
28
18
17
16
7
7
31
35
to pump
"OUT"
thru B136
15
30
73
to sol tank
filter thru
B216
13
14
29
12
33
34
11
10
35
6
32
36
16
9
37
to heater
"IN"
thru AH156
6
7
8
6
38
6
8
41
5
40
39
4
48
1
49
5
5
3
2
46
47
50
45
51
43
34
53
46
to pump
"IN"
thru B186
44
43
45
52
42
73
37
55
72
4
4
71
70
8
56
54
7
69
57
68
8
58
52
67
46
45
28
66
59
19
3
28
62
64
63
61
22
to heater
"OUT"
thru AH105
59
65
60
3
74
75
DATE
10/2013
NAME
43
78
79
80
81
2
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
MYTEE PRODUCTS, INC. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
MYTEE PRODUCTS, INC. IS
PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
CHECKED
DRAWN
83
82
84
M.LaBarbera
52
105
8
106
107
108
109
76
77
2
99
102
103
98
97
6
96
90
89
88
1
DO NOT
SCALE DRAWING
C
REV
SHEET 2 OF 3
C 1001DX-200
SCALE: 1:48
95
94
92
PRODUCTS, INC.
858-679-1191
91
93
59 101 100
88
speedster
SIZE DWG. NO.
TITLE:
mytee
104
97
85
86
87
1
A
B
C
D
E
F
1001DX-200 SPEEDSTER PARTS & PRICING
Power In
2
C322D
L2
C302LA
Vacuum
1
C302LA
L2
Vacuum
2
GND
L1
L2
Pump
115 Volt
Thermal
Switch
Thermal
Switch
Heater 1
1000W
L2
L1 A901
GND
GND
L1
SW
E-515
SW
E-516
Thermal
Switch
Speedster 1001DX-200
Heater 2
1000W
GND
L1
SW
E-515
14
SW
E-515
115V
Thermal
Switch
L2
L1 A901
GND
Power In
1
E-370
Cooling
Fan
C317
L1B
L2B
Float
Switch
Service
Light
E-564
Ground to
Metal Plate
L1A
L2A
1001DX-200 SPEEDSTER WIRING SCHEMATIC
1003DX SPEEDSTER
1003DX SPEEDSTER® BACK
1003DX SPEEDSTER® FRONT
10
1
11
9
2
12
8
3
13
4
7
14
5
1. Switch plate
2. Easy Faucet Fill
3. Solution lid
4. Front handle
5. Front cooling fan
17
6
6. Pressure Regulator
7. Solution tank
8. Female QD with Prime Valve
9. 2” Male Cuff-Lynx™
10.Recovery lid
16
11. Push handle
12. Recovery tank
13. Drain valve
14. Dual Power cords
15. 12” Rear wheels
15
16. Back vent
17. 5” locking casters
1003DX SPEEDSTER® CORD
1003DX SPEEDSTER® ITEMS INCLUDED
Left cord: Powers Vac 2 & Heater 2.
Right cord: Powers Vac 1, Heater 1 & Pump.
Yellow tag
indicates primary
cord.
H110 Cuff-Lynx™
2” Hose Adapter
H375 - Hose Hanger
(4) screws
H141 Cuff-Lynx™
2” Hose Reducer to 1.5”
Plug each power cord into a separate, 20A grounded wall
outlet. Outlets must be on two separate breakers. When
the amber light on the switch plate illuminates, the machine
is on separate circuits (not necessarily 20A circuits). You
can identify the primary cord by the yellow tag.
H226 Drain Elbow
15
1003DX SPEEDSTER
1003DX SPEEDSTER® VAC/SOL
HOSE CONNECTIONS
1003DX SPEEDSTER® SWITCHES
Attach one end of a solution hose to a wand or other tool,
the other end to the Speedster’s® front quick disconnect.
Attach one end of a vacuum hose to the tool, the other end
to the Speedster’s® Cuff-Lynx™ vacuum hose port.
“On” switches are located on the plate in front of the machine. To use vacuums, turn on Vac 1 and Vac 2 switches.
To use pump, turn on Pump switch. To activate heat, use
lower right switch. Press to the left for 1,000 watts, press
to the right for 2,000 watts.
1003DX SPEEDSTER® FILL SOLUTION TANK
1003DX SPEEDSTER® PRIME VALVE
& PRESSURE REGULATOR
PRIME POSITION
HIGHER PSI
RUN POSITION
*Ball valve is
PRESSURE
REGULATOR
located near
the QD.
LOWER PSI
Prime the pump by turning the valve to the Prime position
(as shown above) for 30 seconds, then turn right to the
Run position. Turn the Pressure Regulator to the left to
decrease water pressure. Turn the Pressure Regulator to
the right to increase water pressure.
Lift lid and manually fill the solution tank or use the easy
faucet fill.
16
1003DX SPEEDSTER
1003DX SPEEDSTER® FILTER MAINTENANCE
1003DX SPEEDSTER® FLOAT SWITCH
VACUUM
STACK
FILTER
INTAKE
FILTER
Check and clean the vacuum stack filters and solution
tank filter daily by twisting off, rinsing with clean water and
replacing.
The Speedster® is equipped with an electronic float switch
inside the recovery tank. The recovery float switch is activated by rising water to prevent suction into the vacuum
stacks damaging the motors.
MYTEE® SYSTEM MAINTAINER
1003DX SPEEDSTER® DUMP VALVE
& LOCKING CASTERS
Above, empty the recovery tank by attaching the 45˚ drain
elbow to the drain spout in back. Lift up the dump valve
and empty the tank. Below, locking casters help keep the
machine remain stationary during use.
Weekly flushing of the solution system with Mytee® System
Maintainer helps keep lines clean and prevents chemical
build-up, improving pump life, performance and pressure.
17
Order parts at: www.mytee.com/products/product.php?id=1003DX
18
A
B
C
D
E
F
E550
P731
H256
H528
H903A
E571
E574
H274
E573
18
19
20
21
22
23
24
25
26
PH634-20
B119
47
48
49
H390A
H178
G018
61
62
63
64
H211
G052
H213
H215
66
67
68
69
H203
P732
60
65
H217
PH628-20
59
H194
B160
46
58
B644
45
H124
H347
44
57
PH615-36
43
H768
B105
42
H912
B186
41
56
C313A
40
55
B260A
39
H770
B259A
38
C313C
B652
37
54
AH184
36
53
B260
35
B127
B259
34
52
AH108S
33
B152
B643
32
H044
B113
31
51
B103
30
50
B107
AH156
29
E519
H220
17
B207
H221
16
28
H219
15
27
H251
H666
H371
H342
9
10
14
H210
8
13
H216
7
E564
H273
6
H254
E370
5
11
bolt, 1/4-20 x 1" hex head, s/s
H186
4
12
washer, 1/4" flat, s/s
H343
3
8
nut, hex, 1/4-20 s/s
washer, 1/4" lock, s/s
washer, buna 1-1/8" od x 3/16" id
washer, 1/4"id x 1"od, flat, s/s
bolt, 1/4-20 x 1-1/4"
cover, sol tank (sp)
faucet fill
bracket, "L"
sol tank, speedster
vac hose, 2", wire reinforced
clamp, hose, 2-1/4 dia
coupler, 2" dia x 2.5" length, s/s
Cuff-Lynx, 2" mpt x 2" female cuff
bolt, 1/4-20 x 3/4" serrated hex flange, zinc
bracket, rear, fb/spy
bolt, 1/4-20 x 1/2" serrated hex flange, zinc
regulator, 450 psi, silver spring
plug, brass, 1/4"mpt, hex
bracket, regulator, panel mount
elbow, brass, 90 deg, 1/4" barb x 1/4" mpt
filter, strainer, 1/4"
sol hose, 1/4", 300psi, black
adapter, brass, 1/2" barb x 3/8" fsw, ball end
adapter, brass, 1/2" barb x 1/4" mpt
clamp, hose, 5/16-29/32
sol hose, 1/2" kuri 100psi
bushing, brass, 3/8"mpt x 1/4"
elbow, brass, 90 deg, 3/8"mpt x 3/8" fmpt
pump, CAT, 50-500 PSI, 120/240v
qd, brass, 1/4" mqd x fpt
qd, brass, 1/4" fqd x mpt
elbow, brass, 90 deg, 3/8"mpt x 1/4"mpt
hose, pulse, 3/8" x 17-1/2", (OAL)
qd, brass, 1/4" mqd x fpt
qd, brass, 1/4" fqd x mpt
hose, pulse, 3/8" x 17-1/2", (OAL)
adapter, brass, 3/8" fnpt x 1/4" mnpt
tee, brass, 1/4" fpt
elbow, brass, 90 deg, 1/4"mpt x 1/4" fpt
hose, 3/8" x 6.5", (OAL), f x fsw, 5400 Gray
nipple, brass, 1/4"m, hex
elbow, brass, 90 deg, 1/4" fpt x 1/4" fpt
heating rod, 1000W, 115V
Thermostat, 200°, Auto, 1/4"
screw, 6 x 3/16, phil pan head, self-tapping
Thermostat, 310°F ± 10°F, Manual, 1/4"
heating rod, 600W, 115V
heater, aluminum cast, single
bracket, heater mounting, dual
screw, 10-32 x 3/4" phil pan head, zinc
base, speedster
power cord, pigtail, 30", 12/3, black
fitting, strain relief, cord
nut, lock, 1/2" steel
cap, axle, 1/2"
wheel, 12"
axle, 18.25" x .50" dia
washer, axle, cut 1/2" id
controller, circuit light
caster, 5", Black hub & gray tread
nut, lock, 1/4-20, nylon insert, s/s
nut, kep, #10-32 zinc
controller, water level, dual pump or vac
screw, 10-32 x 3/4, phil flat full thread
screw, #10 x 5/8" hex head zinc
guard, cooling fan, wire
H296
fan, cooling, 115V
DESCRIPTION
C317
8
2
PART NO.
1
ITEM
NO.
7
2
10
6
6
2
1
1
2
1
2
4
2
2
8
1
2
1
1
1
1
1
1
1
1
6
1
1
2
1
3
3
3
2
1
1
2
1
1
5
1
6
2
1
2
10
2
1
2
1
6
1
2
2
2
2
2
1
6
1
2
12
26
14
8
1
4
12
3
1
7
QTY.
$0.99 ea
$0.99 ea
$1.99 ea
$0.99 ea
$0.99 ea
$12.99 ea
$10.99 ea
$6.99 ea
$141.99 ea
$8.99/ft
$1.49 ea
$10.00 ea
$3.99 ea
$0.99 ea
$9.99 ea
$0.99 ea
$86.99 ea
$0.99 ea
$27.99 ea
$5.49 ea
$3.99 ea
$6.49/ft
$3.49 ea
$2.49 ea
$1.99 ea
$8.99/ft
$3.19 ea
$8.99 ea
$599.99 ea
$8.99 ea
$15.99 ea
$8.49 ea
$31.99 ea
$10.49 ea
$11.99 ea
$31.99 ea
$4.99 ea
$6.99 ea
$4.49 ea
$23.99 ea
$3.19 ea
$5.99 ea
$51.99 ea
$16.49 ea
$0.99 ea
$17.99 ea
$49.99 ea
$78.99 ea
$29.99 ea
$0.99 ea
$141.99 ea
$11.49 ea
$3.19 ea
$1.99 ea
$0.99 ea
$41.99 ea
$9.99 ea
$0.99 ea
$62.99 ea
$23.19 ea
$0.99 ea
$0.99 ea
$0.99 ea
$0.99 ea
$94.99 ea
$0.99 ea
$0.99 ea
$2.99 ea
$21.49 ea
MSRP
E512B
H337
E511
E515
E516
H389
H612
H246
H308D
AH203
B156
104
105
106
107
108
109
110
111
112
113
114
120
119
G004
nut, 1/4" npt
hose, pulse, 38" x 34"
gauge, pressure, 2000 PSI
screw, 8-32 x 3/8" SHCS, alloy, Black
Washer, #8, flat regular
screw, 10-32 x 1/2" SHCS, alloy
switch, rocker, 3 position
switch, rocker, 2 position
light, red, 250v
plate, switch,1003DX, 1005DX
light, indicator, 125v (amber)
Cuff-Lynx, 2" m cuff x 2" mpt
gasket, 2" inlet
screw, #8 x 5/8 phil oval, s/s
lid, vac tank, clear, 7"
gasket, 7", vac lid
elbow, inlet assembly 2"
vac tank, speedster
valve, drain, 1-1/2"
spout, drain, 45 degree
adapter, 1.5" pvc, 45 deg, fslip x fslip
PIPE, 1-1/2" x 6" PVC
pipe, pvc, 1-1/2"
filter, foam, 2-3/8" x 1"
screen, mesh filter, 1-1/2" dia
adapter, 1.5" pvc, fslip x fslip
pipe, pvc, 1-1/2"
pipe, pvc, 1-1/2"
adapter, pvc, 1-1/2" mpt x 1-1/2" fms
nut, lock, 1-1/2", steel
filter, strainer, 1/2"
bushing, brass, 1/2"mpt x 3/8" fpt, hex
nipple, brass, 3/8" x close
washer, 11/16"id x 1-1/2"od x .075, s/s
bolt, 1/4-20 x 1/2", hex head, zinc
bracket, front hinge, sp/fb
bolt, 1/4x1-1/2", hex head zinc
handle, breeze and dx
sol hose, 1/4", 300 PSI
adapter, brass, 1/4" barb x 1/4" mpt
ball valve, 1/4''
qd, brass, 1/4" f
tee, brass, 1/4" mpt
coupling, brass, 1/4" fpt x 1/4" fpt
plate, mounting, QD
DESCRIPTION
DATE
10/2013
NAME
PROPRIETARY AND CONFIDENTIAL
Part prices are subject to change.
6
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
MYTEE PRODUCTS, INC. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
MYTEE PRODUCTS, INC. IS PROHIBITED.
SCALE: 1:48
1
858-679-1191
DO NOT SCALE
DRAWING
1003DX
REV
C
SHEET 1 OF 3
speedster
SIZE DWG. NO.
D
TITLE:
mytee PRODUCTS, INC.
gasket, vacuum motor
vac motor, 3 stage, low amp
bolt, hex, 1/4-20 x 4", zinc Finish
vac support, 3 stage, 3.25", no thrds
level switch, vacuum shut-off, rear threads
flat washer, 9/16"ID x 1 1/16"OD, AN960-C916
6
M. LaBarbera
COMMENTS:
CHECKED
DRAWN
C302LA
H096
H503
117
118
E373
116
H212
H135
103
115
G083
H225
96
102
H226
95
H304
P503
94
101
PH633-06
93
G090
PH633-1
92
102
G022
91
G091
G097
90
99
P502
89
P733
PH633-03
88
A926
PH633-4
87
98
P520
86
97
H314
B119A
B210
B216
H299
H201
H378
H316
H485
PH634-36
85
84
83
82
81
80
79
78
77
76
B109
B102
73
75
B135
72
B656
B142
74
H484
71
PART NO.
70
ITEM
NO.
5
A
5
2
2
6
6
1
2
1
1
1
2
3
1
1
3
2
1
1
1
1
6
1
1
1
1
1
1
4
2
2
2
2
2
2
2
2
2
1
1
1
4
2
1
2
1
1
1
1
1
1
1
1
QTY.
$8.99 ea
$139.99 ea
$0.99 ea
$3.99 ea
$13.99 ea
$0.99 ea
$1.99 ea
$47.99 ea
$38.99 ea
$0.99 ea
$0.99 ea
$0.99 ea
$14.99 ea
$13.99 ea
$5.99 ea
$8.99 ea
$9.99 ea
$3.99 ea
$2.49 ea
$0.99 ea
$36.99 ea
$11.99 ea
$15.99 ea
$190.99 ea
$20.99 ea
$3.19 ea
$3.29 ea
$4.99 ft
$4.99 ft
$2.99 ea
$4.99 ea
$5.00 ea
$4.99/ft
$4.99/ft
$2.99 ea
$1.99 ea
$6.49 ea
$2.49 ea
$1.99 ea
$0.99 ea
$0.99 ea
$8.99 ea
$0.99 ea
$6.99 ea
$6.49 ft
$1.99 ea
$13.49 ea
$17.99 ea
$5.49 ea
$4.49 ea
$4.99 ea
MSRP
hanger, wire forned, hose
screw, 10-32 x 1/2" phil pan head, s/s
Cuff-Lynx, 2" to 1.5" reducer
power cord, ext 50', 12/3 black
Cuff-Lynx, 2" hose x 2" fem swivel Cuff-Lynx
stop sign, register your product
H375
H230
H141
E530
H110
AD127
4
gasket, strip, 3/4" x 36" x 1/8"
G085
manual, speedsters
piglet filet
G008
ADM-SPEEDSTERS
DESCRIPTION
PART NO.
ITEMS NOT SHOWN
4
3
1
1
1
2
1
2
1
1
1
QTY.
3
MSRP
$3.99 ea
$74.99 ea
$3.99 ea
$0.99 ea
$10.99 ea
$4.99 ea
$6.29 pak
2
2
1003DX SPEEDSTER PARTS & PRICING
19
A
B
C
D
E
F
15
18
8
17
8
16
14
23
24
25
37
21
22
26
to pump
"OUT"
thru AH184
13
12
20
27
4
6
28
10
11
29
6
7
19
30
29
to female
QD
thru B107
29
to heater
"IN"
thru B107
7
31
31
9
36
8
8
7
6
35
29
32
37
38
5
34
9
39
7
40
4
33
31
12
29
12
49
1
6
113
2
3
58
42
38
47
48
57
to pressure
gauge
thru AH203
41
6
56
45
40
38
44
8
60
54
42
61
50
to sol
tank filter
thru B186
46
55
59
39
40
43
39
53
5
47
to pump
"IN"
thru B160
62
38
52
51
5
81
42
56
81
82
63
65
83
68
66
64
84
80
67
79
67
7
4
56
66
4
8
78
77
66
69
68
67
32
76
20
32
74
72
75
71
85
87
to heater
"OUT"
thru B113
29
29
70
86
88
89
90
91
73
3
92
3
95
94
93
96
94
68
8
119
120
97
102
DATE
10/2013
NAME
M.LaBarbera
117 116
28
2
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
MYTEE PRODUCTS, INC. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
MYTEE PRODUCTS, INC. IS
PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
COMMENTS:
CHECKED
DRAWN
99
118
98
2
114
113
1
DO NOT
SCALE DRAWING
1003DX
C
REV
SHEET 2 OF 3
speedster
SCALE: 1:48
109
108
107
111
110
106
PRODUCTS, INC.
858-679-1191
33
to heater
"OUT"
thru B643
SIZE DWG. NO.
C
TITLE:
105
104
112
103
mytee
115
29
31
6
102
101
1
A
B
C
D
E
F
1003DX SPEEDSTER PARTS & PRICING
Power In
2
L2
C313
Pump
L2
C302LA
Vacuum
1
115 Volt
C302LA
L2
Vacuum
2
Thermal
Switch
Thermal
Switch
Thermal
Switch
Heater 1
600W
L2
L1 A905A
GND
Speedster 1003DX
GND
L1
GND
L1
SW
E-515
SW
E-516
L2
Heater 2
1000W
GND
L1
SW
E-515
20
SW
E-515
GND
A901
115V
Thermal
Switch
L1
Power In
1
E-370
Cooling
Fan
C317
L1B
L2B
Float
Switch
Service
Light
E-564
Ground to
Metal Plate
L1A
L2A
1003DX SPEEDSTER WIRING SCHEMATIC
1005DX SPEEDSTER
1005DX SPEEDSTER® FRONT
1
1005DX SPEEDSTER® BACK
10
11
9
2
12
8
3
18
7
4
13
5
14
6
17
1. Switch plate
2. Easy faucet fill
3. Solution lid
4. Female quick disconnect
5. Front handle
6. Front vent
7. Pressure Regulator
8. Prime Valve
9. 2” Male Cuff-Lynx™
10.Recovery lid
15
16
11. Push handle
12. Recovery tank
13. Drain valve
14. Dual Power cords
15. 12” Rear wheels
16. Back vent
17. 5” locking casters
18. Solution tank
1005DX SPEEDSTER® CORD
1005DX SPEEDSTER® ITEMS INCLUDED
Left cord: Powers power Vac 2.
Right cord: Powers Vac 1 & Pump.
Yellow tag
indicates primary
cord.
H110 Cuff-Lynx™
2” Hose Adapter
H141 Cuff-Lynx™
2” Hose Reducer to 1.5”
H375 - Hose Hanger
(4) screws
H226 Drain Elbow
Plug each power cord into a separate, 20A grounded wall
outlet. Outlets must be on two separate breakers. When
the amber light on the switch plate illuminates, the machine
is on separate circuits (not necessarily 20A circuits). You
can identify the primary cord by the yellow tag.
21
1005DX SPEEDSTER
1005DX SPEEDSTER® VAC/SOL
HOSE CONNECTIONS
1005DX SPEEDSTER® SWITCHES
Attach one end of a solution hose to a wand or other tool,
the other end to the Speedster’s® front quick disconnect.
Attach one end of a vacuum hose to the tool, the other end
to the Speedster’s® Cuff-Lynx™ vacuum hose port.
“On” switches are located on the plate in front of the machine. To use vacuums, turn on Vac 1 and Vac 2 switches.
To use pump, turn on Pump switch. Bottom right switch
has no use.
1005DX SPEEDSTER® FILL SOLUTION TANK
1005DX SPEEDSTER® PRIME VALVE
& PRESSURE REGULATOR
HIGHER PSI
PRIME POSITION
PRESSURE
REGULATOR
LOWER PSI
RUN POSITION
Prime the pump by turning the valve to the Prime position
(as shown above) for 30 seconds, then turn right to the
Run position. Turn the Pressure Regulator to the left to
decrease water pressure. Turn the Pressure Regulator to
the right to increase water pressure.
Lift lid and manually fill the solution tank or use the easy
faucet fill.
22
1005DX SPEEDSTER
1005DX SPEEDSTER® FILTER MAINTENANCE
1005DX SPEEDSTER® FLOAT SWITCH
VACUUM
STACK
FILTER
INTAKE
FILTER
Check and clean the vacuum stack filters and solution
tank filter daily by twisting off, rinsing with clean water and
replacing.
The Speedster® is equipped with an electronic float switch
inside the recovery tank. The recovery float switch is activated by rising water to prevent suction into the vacuum
stacks damaging the motors.
1005DX SPEEDSTER® DUMP VALVE
& LOCKING CASTERS
MYTEE® SYSTEM MAINTAINER
Above, empty the recovery tank by attaching the 45˚ drain
elbow to the drain spout in back. Lift up the dump valve
and empty the tank. Below, locking casters help keep the
machine remain stationary during use.
Weekly flushing of the solution system with Mytee® System
Maintainer helps keep lines clean and prevents chemical
build-up, improving pump life, performance and pressure.
23
Order parts at: www.mytee.com/products/product.php?id=1005DX
24
A
B
C
D
E
F
H378
H210
H213
H201
H216
H316
H342
H666
7
8
9
10
11
12
13
14
B105
B260A
B259A
B644
PH615-37
H347
B160
B652
B107
B643
29
30
31
32
33
34
35
36
37
38
Part prices are subject to change.
P732
PH628-24
H217
H194
H124
PH634-20
B109
H256
H484
AH203
C313C
B135
B102
B656
PH634-36
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
8
H485
H178
G018
45
44
46
47
H211
G052
43
C313A
H768
B186
28
41
42
H202
B246
26
27
B113
H307
H770
24
25
AH184
H221
H912
22
23
40
E550
H220
20
21
39
H371
H251
H219
17
18
19
P731
E370
H186
5
6
H254
H343
H273
3
4
16
H296
2
15
C317
1
8
PART NO.
ITEM
NO.
7
7
sol hose, 1/4", 300 PSI
ball valve, 1/4''
tee, brass, 1/4" mpt
qd, brass, 1/4" f
hose, pulse BLK 49"(OAL), 1/4"fswl x 1/4"fswl
regulator, 450 psi, silver spring
plate, mounting, QD
sol hose, 1/4", 300 PSI
adapter, brass, 1/4" barb x 1/4" mpt
screw, 10-32 x 3/4" phil pan head, zinc
Cuff-Lynx, 2" mpt x 2" female cuff
clamp, hose, 2-1/4 dia
coupler, 2" dia x 2.5" length, s/s
vac hose, 2" wire reinforced, gray
sol tank, speedster
faucet fill
cover, sol tank (sp)
handle, breeze and dx
washer, buna 1-1/8" od x 3/16" id
washer, 1/4"id x 1"od, flat, s/s
pump, CAT, 50-500 PSI, 120/240v
bolt, 1/4-20 x 3/4" serrated hex flange, zinc
hose, pulse BLK 49"(OAL), 1/4"fswl x 1/4"fswl
tee, brass, 1/4" fpt
nipple, brass, 1/4"m, hex
adapter, brass, 3/8" fnpt x 1/4" mnpt
adapter, brass, 1/2" barb x 3/8" fsw, ball end
elbow, brass, 90 deg, 3/8"mpt x 1/4"mpt
sol hose, 1/2" kuri, 100 psi
clamp, hose, 5/16-29/32
qd, brass, 1/4" fqd x mpt
adapter, brass, 1/2" barb x 1/4" mpt
bushing, brass, 3/8"mpt x 1/4"
qd, brass, 1/4" mqd x fpt
elbow, brass, 90 deg, 3/8"mpt x 3/8" fmpt
bolt, 1/4x20x3/4" hex head
plug, brass, 3/8" mpt, hex
washer, star, 1/4" steel zinc
bolt, 1/4-20 x 1/2" serrated hex flange, zinc
nut, lock, 1/2" steel
bracket, rear, fb/spy
power cord, pigtail, 30", 12/3, black
fitting, strain relief, cord
wheel, 12"
cap, axle, 1/2"
axle, 18.25" x .50" dia
washer, axle, cut 1/2" id
base, speedster
bolt, 1/4-20 x 1" hex head, s/s
caster, 5", Black hub & gray tread
bolt, 1/4x1-1/2", hex head zinc
bolt, 1/4-20 x 1/2", hex head, zinc
nut, lock, 1/4-20, nylon insert, s/s
washer, 1/4" flat, s/s
washer, 1/4" lock, s/s
bracket, front hinge, sp/fb
controller, water level, dual pump or vac
screw, 10-32 x 3/4, phil flat full thread
screw, #10 x 5/8" hex head zinc
nut, kep, #10-32 zinc
guard, cooling fan, wire
fan, cooling, 115V
DESCRIPTION
1
1
1
1
1
1
1
1
2
4
2
4
2
2
1
1
1
1
6
6
1
2
1
1
4
1
1
1
1
4
2
1
1
2
2
4
1
2
8
2
1
2
2
2
2
1
4
1
8
2
2
2
14
26
10
1
1
2
12
4
3
1
QTY.
MSRP
6
$6.49 ft
$13.49 ea
$5.49 ea
$17.99 ea
$19.99
$86.99 ea
$4.99 ea
$6.49 ft
$1.99 ea
$0.99 ea
$3.99 ea
$1.49 ea
$10.00 ea
$8.99/ft
$0.99 ea
$10.99 ea
$12.99 ea
$6.99 ea
$1.99 ea
$0.99 ea
$599.99 ea
$0.99 ea
$19.99 ea
$6.99 ea
$3.19 ea
$4.99 ea
$3.49 ea
$8.49 ea
$8.99 ft
$1.99 ea
$15.99 ea
$2.49 ea
$3.19 ea
$8.99 ea
$8.99 ea
$0.99 ea
$1.99 ea
$0.99 ea
$0.99 ea
$1.99 ea
$9.99 ea
$11.49 ea
$3.19 ea
$41.99 ea
$0.99 ea
$9.99 ea
$0.99 ea
$141.99 ea
$0.99 ea
$23.19 ea
$0.99 ea
$0.99 ea
$0.99 ea
$0.99 ea
$0.99 ea
$8.99 ea
$94.99 ea
$0.99 ea
$0.99 ea
$0.99 ea
$2.99 ea
$21.49 ea
6
H203
H215
E564
105
106
107
4
4
manual, speedsters
5
stop sign, register your product
power cord, ext 50', 12/3 black
E530
AD127
Cuff-Lynx, 2" to 1.5" reducer
ADM-SPEEDSTERS
screw, 10-32 x 1/2" phil pan head, s/s
H230
H141
Cuff-Lynx, 2" hose x 2" fem swivel Cuff-Lynx
hanger, wire forned, hose
H110
gasket, strip, 3/4" x 36" x 1/8"
H375
piglet filet
G085
DESCRIPTION
G008
bolt, 1/4-20 x 1-1/4"
nut, hex, 1/4-20 s/s
controller, circuit light
bolt, hex, 1/4-20 x 4", zinc Finish
vac motor, 3-stage hp, 120V, 145"
vac support, 3 stage, 3.25", no thrds
bracket, "L"
gasket, vacuum motor
Cuff-Lynx, 2" m cuff x 2" mpt
gasket, 2" inlet
valve, drain, 1-1/2"
spout, drain, 45 degree
elbow, inlet assembly 2"
nut, lock, 1-1/2", steel
pipe, pvc, 1-1/2"
adapter, pvc, 1-1/2" mpt x 1-1/2" fms
PIPE, 1-1/2" x 6" PVC
adapter, 1.5" pvc, 45 deg, fslip x fslip
pipe, pvc, 1-1/2"
filter, foam, 2-3/8" x 1"
screen, mesh filter, 1-1/2" dia
adapter, 1.5" pvc, fslip x fslip
pipe, pvc, 1-1/2"
lid, vac tank, clear, 7"
screw, #8 x 5/8 phil oval, s/s
vac tank, speedster
gasket, 7", vac lid
level switch, vacuum shut-off, rear threads
elbow, brass, 90 deg, 1/4"mpt x 1/4" fpt
flat washer, 9/16"ID x 1 1/16"OD, AN960-C916
elbow, brass, 90 deg, 1/4" fpt x 1/4" fpt
nut, 1/4" npt
plate, switch,1003DX, 1005DX
gauge, pressure, 2000 PSI
light, indicator, 125v (amber)
screw, 10-32 x 1/2" SHCS, alloy
Washer, #8, flat regular
switch, rocker, 2 position
plug, dome 3/8", black
plug
filter, strainer, 1/2"
sol hose, 1/4" x 24 1/2", (OAL), f x fsw, 3000psi
washer, 11/16"id x 1-1/2"od x .075, s/s
bushing, brass, 1/2"mpt x 3/8" fpt, hex
nipple, brass, 3/8" x close
DESCRIPTION
PART NO.
ITEMS NOT SHOWN
H096
C302A
H503
102
103
104
H390A
G004
H314
94
100
101
PH633-4
P520
92
93
H135
PH633-06
P503
PH633-03
89
90
91
G083
G022
G097
P502
86
87
88
98
PH633-1
85
99
G090
H304
83
84
H225
H226
A926
P733
G091
81
82
95
96
97
E373
B103
79
80
B156
H337
75
76
H212
B207
H308D
E512B
73
74
77
78
E515
H389
H612
70
H422
P967A
68
69
71
72
B119A
AH120
66
67
B216
H299
B210
63
64
65
PART NO.
5
ITEM
NO.
QTY.
1
1
1
2
1
2
1
1
1
3
3
2
2
1
6
2
6
2
2
1
1
1
1
1
2
2
2
2
4
2
2
2
2
2
1
6
1
1
1
1
2
1
1
1
1
1
4
3
3
2
1
1
1
4
1
1
QTY.
$3.99 ea
$74.99 ea
$3.99 ea
$0.99 ea
$10.99 ea
$4.99 ea
$6.29 pak
MSRP
$0.99 ea
$0.99 ea
$62.99 ea
$0.99 ea
$148.99 ea
$3.99 ea
$6.99 ea
$8.99 ea
$3.99 ea
$2.49 ea
$20.99 ea
$3.19 ea
$15.99 ea
$1.99 ea
$4.99/ft
$2.99 ea
$4.99 ft
$3.29 ea
$4.99/ft
$2.99 ea
$4.99 ea
$5.00 ea
$4.99 ft
$36.99 ea
$0.99 ea
$190.99 ea
$11.99 ea
$13.99 ea
$4.49 ea
$0.99 ea
$5.99 ea
$1.99 ea
$8.99 ea
$38.99 ea
$9.99 ea
$0.99 ea
$0.99 ea
$13.99 ea
$1.00 ea
$1.99 ea
$6.49 ea
$35.99 ea
$0.99 ea
$2.49 ea
$1.99 ea
MSRP
NAME
M.LaBarbera
DATE
10/2013
2
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
MYTEE PRODUCTS, INC. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
MYTEE PRODUCTS, INC. IS
PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
CHECKED
DRAWN
2
SCALE: 1:8
1
DO NOT
SCALE DRAWING
1005DX
SIZE DWG. NO.
C
C
SHEET 1 OF 3
REV
PRODUCTS, INC.
858-679-1191
speedster
mytee
TITLE:
1
A
B
C
D
E
F
1005DX SPEEDSTER PARTS & PRICING
25
A
B
C
D
E
F
8
to sol tank
10
9
7
6
32
33
28
4
8
11
5
30
31
34
35
filter thru
B186
8
8
3
27
29
12
2
28
36
1
30
31
37
8
11
11
13
8
26
40
37
7
41
38
14
39
67
to pressure
gauge thru
AH120
7
15
25
24
57
16
to female QD
thru AH203
17
23
22
6
21
6
18
20
19
45
44
5
5
43
46
42
66
64
65
64
64
64
63
28
47
48
62
54
61
4
35
to pump
"IN"
thru B160
4
59
54
38
to pump
"OUT"
thru B643
60
53
49
50
58
55
51
56
52
37
71
72
3
70
74
75
73
37
80
37
68
67
77
76
69
to pump
"OUT"
thru B107
57
3
79
107
4
106
78
83
71
9
43
44
44
43
2
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
MYTEE PRODUCTS, INC. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
MYTEE PRODUCTS, INC. IS
PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
DATE
10/2013
NAME
103
105
84
M.LaBarbera
104
CHECKED
DRAWN
81
82
2
99
87
SCALE: 1:8
1
DO NOT
SCALE DRAWING
1005DX
SIZE DWG. NO.
C
97
96
C
SHEET 2 OF 3
REV
PRODUCTS, INC.
858-679-1191
98
95
speedster
mytee
102
9
8
90
92
101
100
TITLE:
25
94
93
90
91
88
86
89
85
1
A
B
C
D
E
F
1005DX SPEEDSTER PARTS & PRICING
E-564
G
26
L2
L1
G
L2b
L1b
light
L1a
L2a
L2
L1
L2
Ground to
Metal Plate
L1
L2 115V
L2
relays #E-370
Float
Switch
L1
N/O
L2
Pump
VAC 2
VAC 1
L1
C-313A
G
C-302A
G
C-302A
G
Cooling
Fan
C-317
1005DX
115 Volt System
E-515
E-515
E-515
1/27/2014
1005DX SPEEDSTER WIRING SCHEMATIC
GENERAL INFORMATION
Dear Customer:
specify the Model and Serial Number when discussing your machine.
Congratulations on the purchase of your new Speedster® Extractor. As
you are already aware, the scene of the equipment world is becoming
more high tech, and we at Mytee Products Inc. strive to keep you on the
cutting edge with superior quality and technology.
Name Plate
The Model and Serial Number of your machine are shown on the name
plate located on the inside of the machine. This information is needed
when ordering repair parts for the machine. Use the space provided on
the front cover to note the Model and Serial Number of your machine for
future reference.
Keep in mind that the Speedster® Extractor is a machine, so neglect or
abuse will cause unnecessary damage and void the warranty. However
with simple maintenance the Speedster® will give quality performance for
many years to come.
Unpacking the Machine
When the machine is delivered, carefully inspect the shipping carton and
the machine for damage. If damage is evident, save the shipping carton so
that it can be inspected by the carrier that delivered it. Contact the carrier
immediately to file a freight damage claim.
If warranty questions arise, please consult user manual or get in touch with
your distributor. If you have questions about maintenance, replacing parts
or ordering parts, please call an authorized Mytee Products Inc. Service
Center. To see an updated list, visit our website at www.mytee.com
Caution and Warnings
Symbols
Mytee uses the symbols below to signal potentially dangerous conditions.
Always read this information carefully and take the necessary steps to
protect personnel and property.
Before you begin using, please read your manual thoroughly.
Sincerely,
Mytee Customer Care Dept.
Grounding Instructions
This machine must be grounded. If it should malfunction or breakdown,
grounding provides a path of least resistance for electrical shock. This machine is equipped with a cord having an equipment-grounding conductor
and grounding plug. The plug must be plugged into an appropriate outlet
that is properly installed in accordance with all local code and ordinances.
Do not remove ground pin; if missing, replace plug before use.
Is used to warn of immediate hazards that will cause severe personal
injury or death.
Is used to call attention to a situation that could cause severe personal
injury.
Improper connection of the equipment-grounding conductor can result in a
risk of electric shock. Check with a qualified electrician or service person
if you are in doubt as to whether the outlet is properly grounded. Do not
modify the plug provided with the machine. If it will not fit the outlet, have a
proper outlet installed by a qualified electrician.
Is used to call attention to a situation that could cause minor personal
injury or damage to the machine or other property. When using an electrical appliance, basic precautions should always be followed, including the
following: Read all instructions before using this machine. This product is
intended for commercial use only.
This appliance is for use on a nominal 120-volt circuit, and has a grounding plug that looks like the plug illustrated in Figure 1 below. A temporary
adapter illustrated in Figures 2 and 3 may be used~to connect this plug to
a 2-pole receptacle as shown in Figure 2 if a properly grounded outlet is
not available. The temporary adapter should be used only until a properly
grounded outlet (Figure 1) can be installed by a qualified electrician. The
green colored rigid ear, tab or the like extending from the adapter must be
connected to a permanent ground such as a properly grounded outlet box
cover. Whenever the adapter is used, it must be held in place by a metal
screw. Grounding adapters are not approved for use in Canada.
To reduce the risk of fire, electrical shock, or injury:
1. Read all instructions before using equipment.
2. Use only as described in this manual. Use only manufacturer’s recommended attachments.
3. Always unplug power cord from electrical outlet before attempting any
adjustments or repairs.
4. Do not unplug by pulling on cord. To unplug, grasp the plug, not the
cord.
5. Do not pull or carry by cord. Do not close a door on cord or pull cord
around sharp edges or corners.
6. Do not run appliance over cord. Keep cord away from heated surfaces.
7. Do not use with damaged cord or plug. If cord is damaged, repair immediately.
8. Do not use outdoors or on wet surfaces and or standing water.
9. Always unplug or disconnect the appliance from power supply when not
in use.
10. Do not allow to be used as a toy. Close attention is necessary when
used by or near children.
11. Do not use in areas where flammable or combustible material may be
present.
12. Do not leave the unit exposed to harsh weather elements. Temperatures below freezing may damage components and void warranty.
13. Use only the appropriate handles to move and lift unit. Do not use any
other parts of this machine for this purpose.
14. Keep hair, loose clothing, fingers, and all parts of the body away from
all openings and moving parts.
15. Use extra care when using on stairs.
16. To reduce the risk of fire or electric shock, do not use this machine with
a solid-state speed control device.
Replace the plug if the grounding pin is damaged or broken.
The Green (or GreenYellow) wire in the cord is the grounding wire. When
replacing a plug, this wire must be attached to the grounding pin only.
DO NOT use extension cords.
Please Note for America use only
Grounded Outlet
Adapter
Metal
Screw
Grounding Pin
Grounded Outlet Box
Figure 1
Figure 2
Tab for Grounding
Screw
Figure 3
Parts and Service
Repairs, when required, should be performed by Mytee service personnel or Mytee authorized Service Center using Mytee original replacement
parts and accessories. Call Mytee for repair parts or service. Please
27
GENERAL INFORMATION
17. The voltage and frequency indicated on the name plate must correspond to the wall receptacle supply voltage.
18. When cleaning and servicing the machine, local or national regulations
may apply to the safe disposal of liquids which may contain: chemicals,
grease, oil, acid, alkalines, or other dangerous liquids.
19. Do not leave operating unattended.
Please note: Your pump features a pressure switch, to protect vital
components. A minimum spray jet size of 02 needed for use with this
pump. Using a jet size smaller than this can cause back-pressure to
the pump, leading to an over-heat condition. Make sure that your tool
has a jet size of 02 or larger prior to use.
Preparation
1. Before storing machine, drain, rinse and dry tanks and vacuum hose of
water and solution.
2. Store in a dry are in the upright position.
3. Open recover tank cover to promote air circulation.
4. Store indoors in a dry area. If storing in freezing temperatures, make
sure the machine and solution system are completely drained and dry.
After Use
1. Remove furniture and other items from the area you are going to clean.
2. Vacuum carpet and upholstery, and remove debris.
3. Protect cabinets, walls and painted surfaces with drop cloths or plastic.
4. Inspect power cords for damages.
Operating Instructions
Maintenance Schedule
1. Fill the solution tank.
2. Attach one end of a solution hose to a wand or other tool, the other end
to the Speedster’s® front quick disconnect.
3. Attach one end of a vacuum hose to the tool, the other end to the
Speedster’s® Cuff-Lynx™ vacuum hose port.
4. Plug in power cords.
• 1000DX-200 models – Plug single cord into single, 20A grounded wall
outlet.
• 1001DX-200 models – Using two separate circuits/breakers, plug the left
power cord into 20A grounded wall outlet to turn on Vac 2 and Heater 2.
Plug the right power cord into separate 20A grounded wall outlet to turn on
Vac 1, Heater 1 and Pump.
• 1003DX models – Using two separate circuits/breakers, plug the left
power cord into 20A grounded wall outlet to turn on Vac 2 and Heater 2.
Plug the right power cord into separate 20A grounded wall outlet to turn on
Vac 1, Heater 1 and Pump.
• 1005DX models – Using two separate circuits/breakers, plug the left
power cord into 20A grounded wall outlet to turn on Vac 2. Plug the right
power cord into separate 20A grounded wall outlet to turn on Vac 1 and
Pump.
The amber light indicator on the switch plate will illuminate brightly when
cords are plugged into two separate circuits. Do not use extension cords
longer than 50 feet.
5. Turn on switches.
• 1000DX-200, 1005DX models – Turn on Vac 1, Vac 2 and Pump
switches.
• 1001DX-200 and 1003DX – Turn on Vac 1, Vac 2 and Pump switches.
Turn on Heater switch if heat is being used. Wait several minutes for water
to heat. Heater switch has three positions: Off (middle); 1,000 watts using
one heater (left); and 2,000 watts using two heaters (right). Red lights on
panel display indicate watts selected: one light = 1,000 watts; two lights =
2,000 watts; no lights = heaters are off.
6. 1003DX and 1005DX models – Prime Valve and Pressure Regulator
are located on the lower front of the extractor. To prime the pump, turn the
valve to the Prime position for 30 seconds, then turn horizontally to the
Run position. Turn the Pressure Regulator to the left to decrease the water
pressure. Turn to the right to increase water pressure. Level will be visible
on the pressure gauge. Monitor while adjusting, using Pressure Gauge on
Switch Panel.
7. Begin cleaning. Make two dry passes to every wet pass. Work away
from cords to avoid damage. To clean heavily soiled areas, repeat cleaning from a different direction.
8. Use a foam control solution in the recovery tank to prevent motor damage and check for foam build-up in recovery and solution tanks.
9. Empty the recovery tank as needed when the internal ball float automatically shuts off the vacuum. Attach the 45˚ drain elbow to the drain
spout in back. Lift up the dump valve and empty tank.
10. To relieve water pressure from the solution hose before disconnecting
it, squeeze the tool’s trigger five seconds after turning the power switches
off.
11. Once machine is off, unplug power cords. Remove solution and
vacuum hoses. Empty the recovery tank by attaching the 45˚ drain elbow
to the drain spout in back. Lift up the dump valve and empty tank.
12. 1003DX and 1005DX models – Water remaining in the solution tank
can be emptied by turning the Prime Valve to the right to move water into
the recovery tank. Empty recovery tank.
Latches are located in back to open tank for internal maintenance. To
keep machine in good working condition, follow machine’s daily and
weekly maintenance procedures. Check valves and relief valves should be
replaced annually.
Maintenance item
Daily
Clean and inspect tanks.
Clean and inspect hoses.
Check and clean internal filters by twisting
off, rinsing with clean water and replacing.
Check power supply cable.
Clean machine with all-purpose cleaner
and cloth.
Check spray nozzles.
Flush solution system with Mytee® System
Maintainer.
Remove and float shut-off screen from
tank and clean. Simply pull off.
Inspect vacuum hoses for holes and loose
cuffs.
Inspect spray pattern for clogging. If
clogged, remove spray tips and soak them
in a recommended liquid neutralizer for
up to six hours. To remove spray tip, twist
spray tip body counter-clockwise.
Lubricate wheels with water resistant oil.
Inspect machine for water leaks and loose
hardware.
x
x
x
Once a week
x
x
x
x
x
x
x
x
x
Trouble Shooting
There is no power.
1. Plug machine in proper outlet.
2. If using two cords, make sure each is plugged into a separate circuit.
3. Check circuit breaker. Reset circuit breaker, other items should not run
on the same circuit as the machine. Outlet must be a 20-amp circuit.
Pump does not work properly
1. Snap quick disconnects firmly together.
2. Check solution tank; may be empty.
3. Jets clogged, remove jet and flush clean.
4. Filters clogged, remove filters and rinse clean with water.
5. Heater is blocked; flush out with Mytee’s® System Maintainer.
6. If brass check valve is stuck, replace valve.
7. Check pump wire. May need to reconnect wire.
8. Switch plate may need to be replaced.
9. If pump motor brushes are worn, replace pump.
*A minimum spray jet size of 02 needed for use with this pump.
1001DX-200 or 1003DX heater does not work properly
1. If sensor mounted on the heater has popped, reset sensor by pushing
in button.
2. Heating element may need to be replaced.
Vacuum motor does not work properly
1. Check that hose is tightly connected.
2. Close drain hose valve completely.
3. Secure the vacuum tank tightly.
28
GENERAL INFORMATION
PROPER USE AND APPLICATION OF THE GOODS. MYTEE NEITHER
ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME
FOR MYTEE ANY OTHER LIABILITY IN CONNECTION WITH THE
SALE OF MYTEE’S GOODS. THIS LIMITED WARRANTY POLICY MAY
BE CHANGED OR WITHDRAWN BY MYTEE AT ANY TIME WITHOUT
NOTICE.
4. If electronic switch is shut off, empty vacuum tank of all wastewater.
5. If water is coming out of the vacuum motor, use a low foaming
detergent.
6. Clean upholstery tool or floor wand jets.
FAQs
Q: How much do the Speedster® Series extractors weigh and what are
the dimensions?
A: All Speedsters
Machine Dimensions: 28” x 18 ¼” x 40”
Shipping Dimensions: 29 ½” x 19 ¼” x 46 ½”
LIMITATION OF DAMAGES: THE REMEDY OF REPLACEMENT OR
REPAIR OF ANY DEFECTIVE GOODS SHALL BE THE EXCLUSIVE
REMEDY UNDER ANY WARRANTY MADE BY MYTEE, WHETHER
EXPRESS OR IMPLIED. IN NO EVENT SHALL MYTEE BE LIABLE FOR
ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES, PROPERTY
DAMAGES, OR PERSONAL INJURIES.
1000DX-200 – Machine Weight: 83 lbs.
Shipping Weight: 104 lbs.
All limited warranties are void for, and Mytee does not warrant in any way,
any product that evidences misapplication, improper installation, abuse,
lack of maintenance, negligence in use or care, abnormal use, alteration
of design, modification, use of incompatible or corrosive chemicals, use in
a rental service, and/or servicing, installation of parts, or repairs by anyone
other than Mytee or a Mytee authorized distributor or service center. Mytee
may make changes in products it manufactures and markets at any time;
these changes are made without obligation to change, retrofit, or upgrade
any product previously sold or manufactured.
1001DX-200 – Machine Weight: 94 lbs.
Shipping Weight: 124 lbs.
1003DX – Machine Weight: 122 lbs.
Shipping Weight: 150 lbs.
1005DX – Machine Weight: 113 lbs.
Shipping Weight: 140 lbs.
Mytee has no obligation to honor the limited warranties set forth herein
unless the original purchaser, promptly upon discovering the warranty
claim and prior to continuing to use the product, contacts Mytee or a
Mytee authorized distributor or service center to describe the claim and to
receive and follow instructions for documenting and resolving the claim.
In addition, the purchaser must provide the product to which the claim
applies to Mytee or a Mytee authorized distributor or service center for a
thorough inspection. In addition, the purchaser must provide/return the
product intact, unmodified, with all of its original parts.
Q: What comes standard with Speedsters™ extractors?
A: Hose hanger with four screws, two Cuff-Lynx™ Model Numbers: H141
Reducer and H110 Coupler Swivel, and 45˚ drain elbow.
Q: Does Mytee® recommend tools for this machine?
A: All upholstery tools and wands can be used with the Speedster® series.
Q: Is there anything I can do to increase the expected life of my machine?
A: Running the vacuum motors with the tank empty and lid off will allow
excess moisture in the vacs to dry off. You should also run Mytee’s®
System Maintainer through the system to keep the hoses, pump, and
heater clean and free of debris..
If any provision or portion of this limited warranty policy is found to be
unenforceable, then the remaining provisions and portions shall remain
valid and enforceable. If any provision or portion of this limited warranty
policy is found to be limited by law, then that provision or portion shall
be construed to make it effective within the bounds of law. For example,
if there are legal limitations on the duration of warranties, the warranties
made herein shall be construed to have the minimum duration required by
law, or, if there are legal limitations of exclusion of remedies, the exclusions made herein shall be construed to apply to the fullest extent possible
without violating the law.
Warranty
MYTEE LIFETIME LIMITED WARRANTY POLICY
Mytee Products, Inc. endeavors to provide high quality products and
product support to its customers and therefore backs up all of its new
products purchased from Mytee Products Inc. (“Mytee”) or any authorized
Mytee distributor/service center with this lifetime limited warranty. This
limited warranty begins on the date of the customer’s purchase and is
valid and available to the original purchaser with proof of purchase, and is
not transferable. Mytee’s products are for commercial use only and are not
intended for personal, family or household uses.
The validity, construction and performance of this warranty policy shall be
governed by the laws of the State of California, without respect to conflicts
of laws principles. The exclusive jurisdiction of any legal action arising
from or related to this warranty policy shall be in the State of California and
no legal action shall be commenced elsewhere.
HOUSING LIMITED LIFETIME WARRANTY: Mytee warrants for life that
its rotationally-molded housings will be free from manufacturing defects.
This warranty covers the cost of replacement or repair only and does not
cover shipping or labor costs.
Return Material Authorization Procedure
It is the responsibility of any Authorized Service Center (ASC) or Distributor with written authorization to ensure the Customers equipment is
repaired as soon as possible. Only Mytee Products Inc. or it’s authorized
dealers with written authorization, service centers, and agents may make
warranty repairs on these products. All others do so at their own risk and
expense.
WEAR PARTS 90-DAY LIMITED WARRANTY: Mytee will replace all wear
parts for 90 days from the date of original purchase. “Wear parts” are
items which wear out as a result of usage or the passage of time and are
consumed despite attempts to maintain them, such as gaskets, wheels,
brass, cords, wires, electrical terminals, hoses, switches, thermostats,
plastisol parts, filters, bearings, brushes, solenoids, o-rings, bulbs, heating elements, castors, or other parts deemed wear items in Mytee’s sole
discretion. This warranty covers the cost of replacement only and does not
cover shipping or labor costs.
The Distributor must follow Mytee Products, Inc. standard RMA procedure:
1. When a repair falls within the Warranty time period for a piece of equipment, the Distributor will fill out a RMA/Warranty claim form. This form will
act as a repair order to replace any defective parts.
HOWEVER, OTHER THAN SET FORTH HEREIN, MYTEE GIVES NO
WARRANTY, EXPRESS OR IMPLIED, AS TO DESCRIPTION, QUALITY, MERCHANTABILITY, FITNESS FOR ANY PARTICULAR PURPOSE,
PRODUCTIVENESS, INFRINGEMENT, OR OTHER MATTER, OF ANY
GOODS WHICH MYTEE SHALL SUPPLY. THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE
HEREOF. MYTEE SHALL IN NO WAY BE RESPONSIBLE FOR THE
2. All defective parts must be returned to Mytee Products, Inc. with the
RMA/claim form for evaluation at the customer’s expense. This shipping is
non-refundable. All warranty claims are subject to an evaluation by Mytee
Products, Inc. to determine if warranty will be approved. Any credit for
repair and/or parts will only be issued upon evaluation and approval from
29
Mytee Products, Inc.
3. When Warranty is approved, the Distributor’s account will be credited
for the replacement part(s). Mytee Products, Inc. will ship the warranted
replacement part(s) to the Distributor prepaid. If Warranty is denied the
Distributor’s account will not be credited for any parts sent for this claim.
NOTES
30
NOTES
31
NOTES
32