TRI CHLORINE
GENERATOR
INSTRUCTION MANUAL
AND WARRANTY CARD
18058 Zodiac Tri Chlorine Manual.indd 1
23/6/09 3:58:55 PM
THIS KIT CONTAINS:
Part:
Qty:
Description:
a.
1
TRi Power pack
b.
1
Chlorine generating cell
c.
1
Power pack bracket
d.
2
Reducing bushes
18058 Zodiac Tri Chlorine Manual.indd 2
23/6/09 3:58:58 PM
WELCOME TO ZODIAC
Congratulations on your purchase of a product from the Zodiac range of
pool care products. Zodiac products are designed to let you spend more
time enjoying your pool and less on maintenance.
IMPORTANT INFORMATION
YOU MUST READ THIS INFORMATION BEFORE INSTALLATION.
ALWAYS READ THE LABEL AND OPERATION MANUAL BEFORE
USING. PLEASE KEEP YOUR MANUAL AS IT CONTAINS YOUR
WARRANTY.
1
18058 Zodiac Tri Chlorine Manual.indd 3
23/6/09 3:58:58 PM
ZODIAC BELIEVES IN SAFETY FIRST
At Zodiac, we take safety seriously. Always exercise caution when using
electrical appliances and follow the instructions. Failure to do so could
result in permanent injury, electrocution or drowning.
GENERAL WARNINGS
Zodiac saltwater chlorine generators are designed for domestic swimming
pool use only. Contrary use could affect performance and void warranty.
Operating a chlorine generator without water flowing through the cell may
cause a build up of flammable gases, resulting in fire or explosion.
Keep equipment out of reach of children.
A damaged supply cord should only be replaced by the manufacturer,
authorized service agent or electrician.
When installing and using this electrical equipment, always follow basic
safety precautions.
Before performing installation, disconnect all power.
Connect to a circuit that is protected by a ground fault circuit interrupter
(GFCI).
For swimming pools, Australian standards recommend a minimum of 1 Part
Per Million (ppm) of free available chlorine must be maintained at all times.
Service to Zodiac equipment should only be carried out by qualified and
authorized pool professionals.
2
18058 Zodiac Tri Chlorine Manual.indd 4
23/6/09 3:58:59 PM
ZODIAC BELIEVES IN SAFETY FIRST
CHILD SAFETY
Children should not be allowed to operate or perform maintenance on
this product.
No one, particularly children, should sit, step, lean, or climb on any of your pool’s
operational system.
In the interests of child safety, all components of a pool’s operational system
should be located at least 3 metres away from the pool.
ELECTRICAL HAZARD
To avoid accidental contact with lawn mowers and hedge trimmers, power cords
should remain within sight and above ground at all times.
The Zodiac TRI Power pack must not come into contact with water and should
be installed at least 3 metres from the inside wall of your swimming pool.
Should a lack of water be detected, the unit’s electronic flow switch is designed
to turn off the system. Interfering with the electronic flow switch could result in
personal injury and/or damage to the cell.
One pump per electrical socket only (no ancillary equipment should be connected
to the same outlet).
This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction concerning use of the
appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
The installation of the chlorinator should be carried out by a qualified person in
accordance with the Australian wiring rules AS/NZS 3000.
The chlorinator power pack should be located in the correct pool zone and
connected to supply via a power outlet that is protected by a residual current
device (RCD) having a rated residual operating current not exceeding 30mA.
The power outlet should have a degree of protection suitable for the pool zone
Ensure that equipotential bonding of all parts of the pool installation is carried out.
3
INSTALLATION GUIDE
The following steps will help you get up and running with your new Zodiac
TRi Chlorine generator.
POSITIONING THE POWER PACK
1. Locate a suitable space for the power pack bracket. It should be
installed no further than 1.8 meters away from the cell - ideally in a
filtration shed or close to the filtration equipment.
PLEASE NOTE: if fixing to a post it must have a waterproof panel fitted (behind the unit),
at least 450mm wide and 470 mm high.
2. Using screws provided, fasten the bracket securely to the wall and
position the power pack on the bracket. Plug into power point, but
don’t turn on the power.
POSITIONING THE CHLORINE GENERATING CELL
PLEASE NOTE:The cell should always be the last device placed on the water pipe
(In the return line to the pool).
3. Ensure the cell is placed horizontally, with the Inlet pipe connecting to
the fitting closest to the cell lead.
4. Using screw barrel fittings (supplied), attach the cell to the pipe. If using
40mm pipe, you will need to fit the cell using the reducing bushes (also
supplied).
5. When connecting the lead from the power pack to the cell match up
the corresponding colours and pins, then fit the end cap.
(Note: Either RED wire can be connected to either RED pin on the electrode.)
6. Plug your pool pump into the outlet socket in the bottom of the TRi
(this will allow the TRi timer to control the filtration times)
7. Once all connections are together press the mains power switch to ON.
4
18058 Zodiac Tri Chlorine Manual.indd 6
23/6/09 3:58:59 PM
USING INBUILT CLOCK AND TIMERS
When it comes to chlorination, every pool is different. To get what’s right
for you, you will need to set the unit’s clock and timers.
SETTING THE CLOCK
1. Switch power on.
2. Wait for the start-up sequence to complete.
button to enter the MAIN MENU.
3. Press the
4. Use
/
.
5. Press
6. Use
buttons and scroll to SET CLOCK.
/
7. Press
8. Use the
9. Press
buttons to set the hours.
to save the hours.
/
buttons to set the minutes.
to save the minutes.
TRi will then return to the MAIN MENU.
10. Press
to return to the operating screen.
NOTE:The time is displayed in 24 Hour format
5
18058 Zodiac Tri Chlorine Manual.indd 7
23/6/09 3:59:00 PM
USING INBUILT CLOCK AND TIMERS
TURNING CHLORINE GENERATION ON
The chlorine generation of the TRi can be controlled in a number of ways:
1. Manually set to an output level, with the operating times determined by
an external timer.
2. Using the in-built timers on the TRi unit (refer to ‘The Timers’)
3. Using a connection to an external ‘third-party’ controller
(refer to ‘Connecting to a controller’).
To turn the chlorine generation on manually, press the ON/OFF button.
The output level can be set as described in ‘Setting the Chlorine Output.’
NOTE: For safety reasons, the TRi chlorine generator will continually dose chlorine for a maximum of
30 hours if left running with no ‘OFF’ time – unless connected to en external controller. After this time
the TRi will switch to ‘OFF’.
THE TIMERS
The Zodiac TRi chlorine generator comes with two inbuilt timers that
switch the filtration and chlorination system on and off as required.
During swimming season, consider running the system for around 8 hours
a day. This can be increased to 10 hours during periods of very hot weather.
In winter, it may only be necessary to run your pool’s filtration system for
4 hours a day. These shorter periods of activity will lengthen the life of the
unit’s electrode.
For best year round results, set the unit to operate during the cooler hours
of the early morning, evening or when swimmers are using the pool.
PROGRAMMING THE TIMERS
To activate the timer, you will need to enter both an ON and OFF time.
If no OFF time is entered, the chlorine generator will switch off at the
default time of 12:00am (0:00).
You will know that a valid time has been entered when a “T” Symbol is
displayed in the top right hand corner of the LCD display when the unit is
displaying the ‘operating screen’.
6
18058 Zodiac Tri Chlorine Manual.indd 8
23/6/09 3:59:00 PM
USING INBUILT CLOCK AND TIMERS
To program the timer:
1. Press the
2. Press
button.
button to move arrow to ‘SET TIMERS’.
to enter the ‘SET TIMERS’ menu.
3. Press
4. Press
/
.
5. Press
6. Press
to select the timer you wish to set. (Timer 1 or Timer 2)
/
to save the hours.
7. Press
8. Press
/
/
to set the hours (off time).
to save the hours.
11. Press
12. Press
to set the minutes (on time).
to save the minutes.
9. Press
10. Press
to set the hours (on time).
/
13. Press
to set the minutes (off time).
to save the minutes.
TRi will return to the ‘SET TIMERS’ menu.
7
18058 Zodiac Tri Chlorine Manual.indd 9
23/6/09 3:59:00 PM
USING INBUILT CLOCK AND TIMERS
CLEARING THE TIMERS
To clear the timer:
1. Press the
2. Press
button.
/
button to scroll to ‘SET TIMERS’.
to enter the ‘SET TIMERS’ menu.
3. Press
4. Press
5. Press
/
to scroll to ‘CLEAR TIMERS’.
.
A confirmation message will appear on the screen.
EXTERNAL TIME CLOCK
At times, it may be desirable to control chlorine generation using an
external time switch. If the chlorine generator is turned ON, and the
external timer fails to switch the mains power off within 24 hours, the
Zodiac TRi will automatically stop chlorinating in order to prevent over
chlorination.
To set the chlorine generator to run from an external clock:
1. Clear the Timer by following the procedure outlined in ‘Clearing the
Timers’.
2. Press the
button to turn the chlorine generator on.
8
18058 Zodiac Tri Chlorine Manual.indd 10
23/6/09 3:59:01 PM
CHLORINE OUTPUT LEVELS
SETTING THE CHLORINE OUTPUT
The amount of chlorine required by your pool
is dependent on a number of factors including
the size of the pool, the number of users and the
climate.
Output will appear as a percentage on the screen
readout, monitor the level according to the reading
over time will help ensure optimum output.
For users who upgrade to the TRi-PRO model,
chlorine output will be controlled automatically.
To set Chlorine Output levels:
1. Press the
2. Press the
button to turn the chlorine generator on.
/
buttons to set the desired output level.
PLEASE NOTE: if using a pool cover you will need to reduce the chlorine production substantially,
please use LOW mode if you use a cover. Simply press LOW button.
9
18058 Zodiac Tri Chlorine Manual.indd 11
23/6/09 3:59:01 PM
18058 Zodiac Tri Chlorine Manual.indd 12
Frequency of testing
(in peak season)
To decrease*
To increase*
1–3
Ideal reading/range
Weekly
Add
chlorine
or increase
output of
equipment
1–3
Australian Standard
Free
Chlorine
(ppm)
Weekly
Add
muriatic
acid or
dry acid
Add
muriatic
acid
Weekly
Add
sodium
bicarbonate
80 – 140
80 – 300
Total
Alkalinity
(ppm)
Add buffer
or soda ash
(sodium
carbonate)
7.5
7.2 – 7.8
pH
Weekly
Partially
drain
& refill pool
Add
calcium
chloride
90 – 300
90 – 300
Calcium
Hardness
(ppm)
CORRECT SETTINGS FOR YOUR TRI CONTROLLED POOL
Weekly
Partially
drain
& refill pool
Add
Cyanuric
acid
50
30 – 50
Cyanuric
Acid
(ppm)
Monthly
Partially
drain
& refill pool
Add Salt
4000 ppm
at 27ºC**
4000 - 7000
Salt
Level
(ppm)
Quarterly
Sensors
CORRECT SETTINGS FOR YOUR TRI CONTROLLED POOL
10
23/6/09 3:59:01 PM
CONNECTING TO A CONTROLLER
If you use a Master Control Device
(MCD) to control your pool you will
need to configure your TRi Chlorine
generator to allow “communication”
between the two.
You must set the controller type
on the TRi before making the
wiring connection.
SETTING THE CONTROLLER
(To be done before making a wiring connection)
1.
Switch power to the TRi unit on.
2.
Wait for the start-up sequence to complete.
3.
Press the
4.
Press the
5.
Press
6.
Press
7.
Press
8.
TRi will return to the main menu.
9.
Press
button.
button to scroll down to ‘CONTROLLER’.
to enter the controller menu.
/
to highlight the controller being used.
to save the controller setting.
to return to the operating screen.
11
18058 Zodiac Tri Chlorine Manual.indd 13
23/6/09 3:59:02 PM
CONNECTING TO A CONTROLLER
ATTENTION JANDY ‘REV L’ OR LATER USERS
It is critical that the controller setting to be set to JANDY L/M if a
controller that is a Jandy Aualink ‘Rev L’ or later, is to be connected. If the
incorrect setting is selected, damage can be caused to the Jandy Aqualink
Control Unit.
CAUTION WHEN WIRING TO A CONTROLLER
IMPORTANT
Wiring of the controller should be completed by an authorised pool
equipment installer.
Before any wiring connections/disconnections ensure mains power is
removed from both the controller and the Zodiac TRi unit.
When connected to a controller, the TRi Chlorine generator acts as the
‘slave’ - responding to requests. This means timer settings are ignored and
the output settings cannot be changed, although all other ‘menu’ functions
are still accessible, except for LOW and BOOST modes.
WIRING TO A CONTROLLER
The following instructions should be read in conjunction with the
installation guide provided with the Controller.
1. Remove silver ‘dress’ cover by pressing
in at the sides where indicated below
and lift.
2. Remove the two screws which attach
the lower cover to the main unit:
12
18058 Zodiac Tri Chlorine Manual.indd 14
23/6/09 3:59:02 PM
CONNECTING TO A CONTROLLER
3. Remove the lower cover from the
TRi unit.
NOTE: If using either pH upgrade or PRO unit –
carefully disconnect the ribbon cable from the TRi unit.
4. Remove the small white bung closest
to the centre of the lower panel of the
TRi unit.
5. Thread the controller cable through
the hole (a grommet may be necessary
depending on the size of the cable
being used).
6. Attach a cable tie to the controller
cable as shown in the diagram.
The wiring colour coded are outlined
below:
Depending on the make of the Controller, make the following wiring
connections:
Polaris EOS/ Jandy Aqualink
Green wire (0V) to ‘0V’ terminal on the TRi
Red wire to the (+V) ‘POS’ terminal on the TRi
Yellow/White (B) wire to ‘B’ terminal on TRi
Black wire (A) to ‘A’ terminal on TRi
Pentair Intellitouch
GREEN wire to ‘B’ terminal on TRi
Red wire to ‘POS’ terminal on TRi
Yellow wire to ‘A’ terminal on TRi
Black wire to ‘0V’ terminal on TRi
13
18058 Zodiac Tri Chlorine Manual.indd 15
23/6/09 3:59:08 PM
CONNECTING TO A CONTROLLER
TESTING THE WIRING CONNECTION
Once a connection has been made between the Controller and the
Chlorine generator, it will need to be tested.
1. Turn on the power to the Controller and the Zodiac TRi.
2. If successful, a ‘ ’ symbol will appear in the top right hand corner of the
screen after about 20 seconds.
3. If the controller does not connect, turn power off to both the devices
and try again.
VERIFY THE WIRING CONNECTIONS
To verify the connection:
1. Switch the TRi unit on and check the controller setting (follow
instructions under ‘SETTING CONTROLLER’.
2. Re-test the connection.
Note: For safety reasons, the Zodiac TRi reverts to the OFF setting if the communication
connection is lost.
CONNECTION TO CONTROLLER FOR POOL/SPA
COMBINATIONS
To connect a Zodiac TRi unit to Pool or Spa Valves, you will need to make
a “splice” into the control lines from the Controller, located inside the
controller itself.
For further information, consult the installation manual of the Controller
being used.
14
18058 Zodiac Tri Chlorine Manual.indd 16
23/6/09 3:59:08 PM
SETTING THE MODE TO LOW: IMPORTANT IF USING A POOL COVER
If your pool has a cover, you should set the output
level to “low”. This is also known as “winter” mode.
Reducing your chlorine output will help prevent
damage to your pool’s cover and other equipment.
MANUAL SETTING
1. To select Low mode press
.
This will drop the chlorine output to around 10%.
2. ‘Low’ will appear on the screen.
Note: Low or Winter mode cannot be selected when TRi is being
controlled by an external controller.
AUTOMATIC SETTING
The Zodiac TRi can be connected to the valves of an automatic pool/spa
system.
When the input from the valves is set to ‘Low’ the TRi will automatically
revert to ‘Low’ mode and the output will be locked at 10%
Details of the wiring connection are outlined in the ‘‘Connection to Automatic
Pool/Spa Valve” section of this manual.
For users who have upgraded to the TRi-pH or TRi-PRO, the
automatic pH/ACL control function is disabled when in LOW
mode.
15
18058 Zodiac Tri Chlorine Manual.indd 17
23/6/09 3:59:08 PM
THE BOOST SETTING
At times your pool may require a larger than normal application of
chlorine. The Boost function is used to rapidly add chlorine.
In BOOST or “Superchlorinate” mode, output settings are temporarily
overridden and the chlorine generator runs for 24 hours at 100% Chlorine
Production.
In ‘TIMER’ mode, the circulation pump will run for 24 hours, before
automatically reverting to previous output / timer settings.
In ‘MANUAL’ mode, the chlorine generator will run at 100% for a
cumulative total of 24 hours before reverting to the previous
output setting.
NOTE:
The ‘BOOST’ mode cannot be engaged under the following
curcumstances:
1) If the TRi is in the ‘OFF’ operating mode.The chlorinator must be
‘ON’ for BOOST to be engaged.
2) If you have upgraded to the TRi-PRO
3) Or from the front panel when the TRi is being controlled by an
external controller.
In most cases a BOOST function can be set from the controller menu.
Consult your third party controller manual for more information.
SETTING THE BOOST MODE
To activate the BOOST setting:
Press the
button.
‘BOOST’ will be displayed on the screen and chlorine generation will
commence.
16
18058 Zodiac Tri Chlorine Manual.indd 18
23/6/09 3:59:08 PM
HELP AND TROUBLESHOOTING
The Zodiac TRi chlorine generator automatically provides a number of
inbuilt warnings that can help identify problems and offer solutions.
To access the HELP menu:
1. Press the
button.
/
2. Using the
buttons, scroll to the ‘HELP/DIAG’ menu.
to enter the ‘HELP/DIAG’ menu.
3. Press
4. Once in the ‘HELP/DIAG’ menu, use the
/
buttons to scroll to
the error/warning that has been displayed.
5. Press
.
A number of suggested solutions are momentarily displayed, in order of
priority.
After displaying, the TRi automatically reverts back to the ‘HELP/DIAG’
menu.
6. To exit to the default operating screen wait ~5 seconds
OR press the
button.
17
18058 Zodiac Tri Chlorine Manual.indd 19
23/6/09 3:59:09 PM
MAINTENANCE
To keep your TRi Unit in the best possible condition it is recommended
regular maintenance should be performed.
INSPECTING AND CLEANING THE ELECTRODE
In areas that experience calcium hardness the TRi electrode will benefit
from cleaning.
To clean your electrode:
1. Switch off the filter pump and chlorine generator, close necessary valves
and unplug the cell terminal cap.
2. Unscrew the retaining ring and
remove the electrode. If calcium
buildup is present, immerse the
electrode in cell cleaning solution
without immersing the terminals.
3. If you do not use commercial
cleaning solution, you can mix your
own by carefully adding one (1)
part of Hydrochloric (Muriatic) acid
to ten (10) parts water. Stronger
solutions will shorten terminal life.
4. Allow the cleaning solution to dissolve the calcium deposits for about
10 minutes. Dispose of the cleaning solution at an approved Council
Depot and never into storm water or sewage drains.
6. Rinse the electrode in clean water and re-fit the electrode in the cell
housing.
7. Replace the cell head and plug
assembly and reset valves and
switches. Turn pump and TRi on.
8. Confirm chlorine output and
settings on the power pack. Timer
settings will be automatically
retained.
18
18058 Zodiac Tri Chlorine Manual.indd 20
23/6/09 3:59:09 PM
ERRORS AND WARNINGS. WHAT THEY MEAN.
NO FLOW
Diagnosis: Insufficient water flow in the cell.
This could mean the circulation pump has ceased to function, or the filter
needs cleaning. The chlorine output will be turned off at this time.
CHECK SALT
Diagnosis: Salt level is between 3000 and 4000 ppm, depending on the
water temperature.
Always maintain a salt level above 4000ppm. if you don’t know what your
salt level is or how to test it, consult your local pool care professional.
OUTPUT FAULT
Diagnosis: There could be a problem with the power supply. Turn power off
at the power point and consult your local pool care professional.
CLEANING
Diagnosis: The cell is in the process of reversing polarity.
Wait approximately 5 minutes and chlorine production should resume as
normal.
19
18058 Zodiac Tri Chlorine Manual.indd 21
23/6/09 3:59:12 PM
TROUBLESHOOTING
Additional information about this product can be found at
zodiac.com.au
For further information and assistance please consult your local pool
professional.
Your Local Dealer:
20
18058 Zodiac Tri Chlorine Manual.indd 22
23/6/09 3:59:12 PM
WARRANTY
TRi Saltwater Chlorine generator Warranty*
Your Zodiac TRi Saltwater Chlorine generator has been manufactured with
the greatest of care and from the best available materials. Please refer to
the fine print should you need to make a warranty claim.
Chlorine generator (excluding cell electrodes) Warranty
The manufacturer warrants for a period of 3 years from the date of
purchase, in respect of defects found to be solely due to faulty materials or
workmanship that it will repair or replace at its option such faulty materials
or parts free of charge.
Electrode Warranty
The cell electrodes and their special coatings are covered by a 3 year
warranty, please refer to fine print for exclusions and exceptions.
Should you have any issues please consult your local pool care professional.
*The warranty applicable to commercial application is limited to
12 months from the date of installation.
21
18058 Zodiac Tri Chlorine Manual.indd 23
23/6/09 3:59:12 PM
WARRANTY
ZODIAC WARRANTY TERMS AND CONDITIONS
Subject to the terms and conditions set out below, Zodiac Group Australia
Pty Ltd (ABN 87 002 641 965) (“Zodiac”) agrees to repair or replace at
Zodiac’s cost the Zodiac product which this warranty card accompanies
(“the Product”), and any Zodiac component supplied with it, originally
purchased by you from a Zodiac Authorised Dealer when the Product does
not perform in accordance with the manufacturer’s specifications or is
otherwise defective during the relevant Warranty Period(s) from the date
of purchase. Specific warranty periods for individual products (including
any extended warranty offered) are stated on the relevant product
documentation concerning those specific products. This warranty only
covers factory imperfections in materials and workmanship and does not
cover normal wear and tear. Other exclusions apply — see below.
Warranty Claim Procedure
1. No claim under this warranty will be recognised unless the Zodiac
product registration card is completed online at www.zodiac.com.au
or returned to Zodiac Registration Dept, GPO Box 2637, Sydney NSW
2001, within fourteen (14) days of the day of purchase.
2. Any claim must be limited to those claims which may be asserted under
the scope of this warranty outlined in this document. Claims should be
lodged as soon as possible after any defect in the Product is discovered.
3. To make a warranty claim, the Product must be returned, to the Zodiac
Authorised Dealer where the product was purchased. When submitting
a claim, always supply serial number, evidence of purchase date, retailer
and a brief description of the problems/defects encountered. We
suggest you contact your Zodiac Authorised Dealer in the first instance,
who will assist you in making a warranty claim.
4. When outside of the manufacturers build date a proof of purchase (i.e.
bill of sale, invoice or purchase receipt) may be required when making a
claim under this warranty.
5. Zodiac reserves the right to replace the Product or relevant part with
the same or equivalent Product or part, rather than repair it. Where
a replacement is provided the Product or part replaced becomes the
property of Zodiac. Zodiac may replace parts with refurbished parts.
22
18058 Zodiac Tri Chlorine Manual.indd 24
23/6/09 3:59:12 PM
WARRANTY
Replacement or repair of the Product or a part does not extend or restart
the Warranty Period(s). Zodiac replacement parts come with separate
warranties for the part itself. Alternatively Zodiac may, in its sole
discretion, elect to refund the purchase price paid in lieu of replacing or
repairing a defective Product via their authorized dealer network.
6. Zodiac and/or its Authorised Service Centres may seek reimbursement
of any costs incurred by them (including labour charges) when the
Product or relevant part is found to be in good working order or if the
warranty claim is invalid.
General Exclusions and Limitations
7. This warranty will not apply in any of the following circumstances:
(a) If the factory-applied serial number has been altered or removed
from the Product.
(b) Damage, malfunction or failure resulting from alterations, accident,
misuse, abuse, fire, liquid spillage, mis-adjustment of customer
controls, use on an incorrect voltage, power surges and dips,
thunderstorm activity, acts of God, voltage supply problems,
tampering, unauthorised repairs or other acts by any persons
(including any repairs by persons other than Zodiac authorised
service personnel), use of defective, incompatible or non-genuine
parts or accessories, exposure to abnormally corrosive conditions
or entry by any insect, vermin or foreign object in the Product.
(c) Damage arising during transportation, installation or while moving
the Product.
(d) Any failure, to the extent that the failure is not a failure of the
Product to perform in accordance with its specifications or results
from a defect in its materials or workmanship.
(e) Replacement or repair of any lost or stolen parts or accessories.
(f) Discoloration of the Product caused by prolonged UV exposure or
reaction to chemicals used in the pool water. Zodiac products are
designed so that discolouration will not affect their operating ability.
(g) Damage to or malfunction of the Product resulting from excess
chlorination or improper water chemistry balance, including where
swimming pool water is not balanced in accordance with Zodiac’s
recommendations.
23
18058 Zodiac Tri Chlorine Manual.indd 25
23/6/09 3:59:13 PM
WARRANTY
(h) Replacement of parts which fail or become defective as a result
of improper installation, negligence, misuse, abuse or tampering by
unauthorised repair personnel.
(i) Damage to pool liners due to age, pool water imbalance improper
installation and corrosion of the supporting walls and/or
irregularities in the pool base. The use of this Product in such an
environment is at the pool owner’s sole risk.
(j) Abrasion to hoses or damage caused by misuse or improper
installation.
(k) Damage where the Product is used outside of recommended
operating conditions or where Zodiac’s instructions regarding
installation, operation, maintenance or servicing of the Product are
not followed.
8. This warranty gives you specific legal rights You also have certain rights
under Federal or State legislation which are not able to be excluded,
restricted or modified by this warranty. All other conditions, warranties,
terms and obligations in respect of the Product, express or implied by
law are excluded, other than as expressly set out in this warranty.
9. To the extent permitted by law, Zodiac’s liability for any claim arising
from a breach of any term, condition or warranty implied by statute
which cannot by law be excluded (except for a breach of section 69 of
the Trade Practices Act 1974 ) is limited, at Zodiac’s option, to the repair
or replacement of the Product or the payment of the cost of having
the Product repaired or replaced. Any such implied term, condition or
warranty will be limited to the duration of the Warranty Period.
10. (whether material or personal) arising out of or in connection with any
defect of the Product or any negligence by Zodiac, including, but not
limited to, injuries to persons, damages to property or loss of use.
11. Zodiac’s aggregate liability in respect of all claims under this warranty
shall not exceed the original purchase price of the Product or, at
Zodiac’s option, the cost of replacing the Product.
24
18058 Zodiac Tri Chlorine Manual.indd 26
23/6/09 3:59:13 PM
WARRANTY
Freight Charges
12. Zodiac may, in its sole discretion, accept responsibility for the payment
of freight to and from your chosen delivery address within Australia. In
the event that no-one is available to sign for the goods being collected
or delivered, a delivery fee may be charged and must be paid prior to
any goods being returned to you.
13. If you have not collected any replacement or repaired Product or paid
relevant delivery fees within 12 months of making a warranty claim,
Zodiac will be under no obligation to return the Product and may
dispose of it as Zodiac sees fit.
General Conditions
14. Zodiac assumes no responsibility for any warranties or representations
made by other individuals or businesses beyond the express terms
contained in this warranty.
15. This warranty is not transferable and does not apply to subsequent
owners of the Product.
This warranty is governed by the laws of New South Wales.
25
18058 Zodiac Tri Chlorine Manual.indd 27
23/6/09 3:59:13 PM
Zodiac is a registered trademark of Zodiac Group Australia Pty Ltd
ABN 87 002 641 965
ZODIAC CUSTOMER SERVICE CENTRE
Zodiac Group Australia:
219 Woodpark Rd, Smithfield,
NSW 2164 Australia
Tel: 1800 688 552
688
Fax:Fax:
+611300
(0) 2781
8786
6800
Email: aftersales@zodiac.com.au
www.zodiac.com.au
© Copyright Zodiac Australian Ltd 2008
18058 Zodiac Tri Chlorine Manual.indd 28
W176781
Due to constant developments and improvements,
specifications may change without notice.
Improper use could affect performance and void warranty.
23/6/09 3:59:13 PM