Mitsubishi Electric PAR-21MAA Installation manual

WT04465X01
GB
6
CAUTION Do not tighten the screws too tight. Doing so may deform or crack the lower cover.
NOTE: - Choose a flat plane for installation.
- Fasten the switch box at more than two places when installing directly on the wall.
- When reinstalling on the wall, fasten securely using anchors.
CITY MULTI Control System
and Mitsubishi Mr. SLIM Air Conditioners
5.
MA Deluxe Remote Controller
To indoor unit MA remote
controller or A controll
terminal block
CAUTION
Do not use crimp terminals to connect to remote controller terminal blocks. The terminals may contact the board and cause
trouble or contact the cover and damage the cover.
CAUTION Prevent remote cord chips from getting into the remote controller. Electric shock or malfunction may result.
1 Safety Precautions
6.
● Read these Safety Precautions and perform installation work accordingly.
● The following two symbols are used to dangers that may be caused by incorrect use and their degree:
7.
This symbol denotes what could lead to serious injury or death if you misuse the PAR-21MAA.
Wiring hole for installing directly on the wall (or open wiring)
• Cut off the shaded area from the upper cover using a knife, nippers, etc.
• Take out the remote control cord connected to the terminal block via this portion.
Install the cover to the remote controller.
● After reading this installation manual, give it and the indoor unit installation manual to the end user.
● The end user should keep this manual and the indoor unit installation manual in a place where he or she can see it at anytime. When someone moves
or repairs the PAR-21MAA, make sure that this manual is forwarded to the end user.
(Hold down the E button and press the D button for two
seconds.)
* The display cannot be changed during the unit function
selection, the test run and the self diagnosis.
Install in a place which is strong enough to withstand the weight of the
PAR-21MAA.
Any lack of strength may cause the PAR-21MAA to fall down, resulting in
personal injury.
All electrical work must be performed by a licensed technician, according to local regulations and the instructions given in this manual.
Any lack of electric circuit or any deficiency caused by installation may result
in an electric shock or fire.
Firmly connect the wiring using the specified cables. Carefully check
that the cables do not exert any force on the terminals.
Improper wiring connections may produce heat and possibly a fire.
Do not move and re-install the PAR-21MAA yourself.
Any deficiency caused by installation may result in an electric shock or fire.
Ask your distributor or special vendor for moving and installation.
Never modify or repair the PAR-21MAA by yourself.
Any deficiency caused by your modification or repair may result in an electric
shock or fire.
Consult with your dealer about repairs.
To dispose of this product, consult your dealer.
CAUTION Press the cover until it snaps shut. If not, it may fall off.
Item 1
CAUTION Do not into turn the screwdriver in the slot. Doing so may damage the slot.
NOTE: A protection sheet is stuck to the operation section. Peel off this protection sheet before use.
Item 2
4
Press the
E button.
Operation mode display
“TEST RUN” and “OPERATION MODE” are
displayed alternately.
Test Run
1. Before making a test run, refer to the “Test Run” section of the
indoor unit installation manual.
2. Press the [TEST] button twice successively within three seconds.
Test run starts.
3. Stop the test run by pressing the [ ON/OFF] button.
4. If trouble occurred during the test run, refer to the “Test Run” section of the indoor unit installation manual.
Timer stops test run after two hours.
Piping temperature display
BACK
PAR-21MAA
MONITOR/SET
ON/OFF
FILTER
DAY
CLOCK
CHECK TEST
OPERATION
CLEAR
ON/OFF] button.
Press the
Mode selection G button.
During test run, the RUN lamp remains on.
(“MODE
SELECTION”)
[TEST] button
Press the
E button.
Do not use in any special environment.
Using in any place exposed to oil (including machine oil), steam and sulfuric
gas may deteriorate the performance significantly or give damage to the component parts.
5
Do not install in any steamy place such a bathroom or kitchen.
Avoid any place where moisture is condensed into dew. Doing so may cause
an electric shock or a malfunction.
Press the
Display change G button.
(“DISP MODE
SETTING”)
[Setting Procedure]
1 Stop the air conditioner using the remote controller [ ON/OFF] button.
If the OFF display shown below does not appear at this time, step 2 cannot be performed.
Do not wash with water.
Doing so may cause an electric shock or a malfunction.
Do not press any control button using a sharp object.
Doing so may cause an electric shock or a malfunction.
2 Press and hold down the [FILTER] and [
] buttons at the same time for two seconds. The display shown below appears. The remote controller
confirms the registered LOSSNAY addresses of the currently connected indoor units.
Do not install in any place at a temperature of more than 40°C or less
than 0°C or exposed to direct sunlight.
Doing so may cause deformation or malfunction.
2
3 Registration confirmation result
- The indoor unit address and registered LOSSNAY address are displayed alternately.
Confirming the Supplied Parts
Confirm that the box includes the following parts, in addition to this installation manual:
1. Remote controller (cover, body) ..................................................................................... 1
2. Cross recessed pan head screw (M4 × 30) .................................................................... 2
3. Wood screw (4.1 × 16, used for directly hooking to the wall) ......................................... 2
4. Caution label (in 12 languages) ..................................................................................... 1
*1 For the remote control, obtain a 2-core cable between 0.3 and 1.25 mm2 at the site.
*2 PAC-YT32PTA cannot be connected.
3
1.
<Indoor unit address and indoor unit display>
Remote controller cover
<LOSSNAY address display and LOSSNAY display>
- When LOSSNAY are not registered
Remote controller body
1
3
4 If registration is unnecessary, end registration by pressing and holding down the [FILTER] and [
] buttons at the same time for two seconds.
If a new LOSSNAY must be registered, go to step 1. Registration procedure. If you want to confirm another LOSSNAY, go to step 2. Confirmation
procedure. To delete a registered LOSSNAY, go to step 3. Deletion procedure.
How To Install
Choose a place in which to install the remote controller (switch box).
Be sure to observe the following steps:
(1) Temperature sensors are provided with both the remote controller and the indoor units. When using the
remote controller temperature sensor, the master remote controller detects the room temperature. Install
the master remote controller in a place where the average room temperature can be detected and which
is not affected by any heat source from direct sunlight or air blown from air conditioning units.
External size
of remote
controller
< 1. Registration procedure >
5 Set the address of the LOSSNAY and the indoor unit connected by the remote controller you want to register using the [
buttons. (01 to 50)
6 Set the address of the LOSSNAY you want to register using the [ CLOCK ( ) and ( )] buttons. (01 to 50)
Extra space
around remote
controller
30 mm
30 mm
120 mm
46
102
Indoor unit address
LOSSNAY address
7 Press the [TEST] button, and register the set indoor unit address and LOSSNAY address.
- Registration end display
The indoor unit address and “IC” and LOSSNAY address and “LC” are alternately displayed.
25
25
10
44
< 2. Confirmation procedure >
8 Set the address of the indoor unit connected by the remote controller whose LOSSNAY you want to confirm using the [
buttons. (01 to 50)
TEMP. (
) and (
)]
Switch box
Seal around here
with putty.
Remote control
cord
3.
For taking cord
out from back of
remote
controller
G
Press the
D button.
MENU
BACK
MONITOR/SET
PAR-21MAA
ON/OFF
ON/OFF
Filter sign
- Confirmation end display (When LOSSNAY is not connected.)
Fan speed
Registered indoor unit address does not exist.
No. of air outlets
Installed options
Up/down vane setting
Energy saving air flow
A Press the [ ON/OFF] button twice and delete registration of the LOSSNAY registered at the set indoor unit.
- Deletion end display
Indoor unit address and “– –” and registered LOSSNAY address and “– –” are alternately displayed.
Remove the remote controller cover.
• Insert a minus screwdriver into one of the open slots and move the screwdriver in the arrow direction.
Indoor unit
Registration
OPERATION
B
CLEAR
H
See [4]-4. (2)
Automatic cooling/heating display setting (“AUTO MODE DISP C/H”)
See [4]-4. (3)
C
Unit address Unit address Unit address
No. 03
No. 01
No. 02
Fan operation
Remote Controller
* When grouping by different refrigerant systems and an indoor unit other
than the specified refrigerant address performs the fan operation, the
refrigerant address set here is probably duplicated.
Recheck the refrigerant address at the outdoor unit rotary switches.
A
CHECK TEST
6 Mode No. selection
Select the mode No. you want to set with the F [
D
TEMP. (
) and (
)] buttons. (Only the settable mode numbers can be selected.)
Mode No. display
(3) Temperature range limit setting
After this setting is made, the temperature can be changed within the set range.
• To switch the setting, press the [ ON/OFF] button.
1 LIMIT TEMP COOL MODE :
The temperature range can be changed on cooling/dry mode.
2 LIMIT TEMP HEAT MODE :
The temperature range can be changed on heating mode.
3 LIMIT TEMP AUTO MODE :
The temperature range can be changed on automatic mode.
4 OFF (initial setting) :The temperature range limit is not active.
* When the setting, other than OFF, is made, the temperature range limit setting
on cooling, heating and automatic mode is made at the same time. However,
the range cannot be limited when the set temperature range has not changed.
• To increase or decrease the temperature, press the [ TEMP ( ) or ( )] button.
• To switch the upper limit setting and the lower limit setting, press the [
]
button. The selected setting will flash and the temperature can be set.
• Settable range
Cooling/Dry mode : Lower limit: 19°C ~ 30°C Upper limit: 30°C ~ 19°C
Heating mode :
Lower limit: 17°C ~ 28°C Upper limit: 28°C ~ 17°C
Automatic mode : Lower limit: 19°C ~ 28°C Upper limit: 28°C ~ 19°C
* The settable range varies depending on the unit to connect (Mr. Slim units,
Free-plan units, and intermediate temperature units)
[4] -3. Mode selection setting
(1) Remote controller main/sub setting
• To switch the setting, press the [ ON/OFF] button.
1 Main : The controller will be the main controller.
2 Sub : The controller will be the sub controller.
5
CALL_
: The contact number can be set when the display is as
shown on the left.
• Setting the contact numbers
To set the contact numbers, follow the following procedures.
Move the flashing cursor to set numbers. Press the [ TEMP. ( ) and
( )] button to move the cursor to the right (left). Press the [ CLOCK
( ) and ( )] button to set the numbers.
Settings
Not available
Available (Approximate 4 minutes wait-period after power is restored.)
Indoor unit operating average
Set by indoor unit’s remote controller
Remote controller’s internal sensor
Not Supported
Supported (indoor unit is not equipped with outdoor-air intake)
Supported (indoor unit is equipped with outdoor-air intake)
Energy saving cycle automatically enabled
Energy saving cycle automatically disabled
100 Hr
2500 Hr
No filter sign indicator
Quiet
Standard
High ceiling
4 directions
3 directions
Not supported
Supported
No vanes
Equipped with vanes (No. 1 set)
Equipped with vanes (No. 2 set)
Disabled
Enabled
Not supported
Supported
7 Select the setting contents of the selected mode.
When the G [ MENU] button is pressed, the current setting No.
flashes. Use this to check the currently set contents.
8 The contents set at steps 3 to 7 are registered.
When the E [
] button is pressed, the mode No. and setting No. flash and registration begins. The flashing mode No. and
setting No. change to a steady light and setting ends.
* When “– –” appears at the mode No. and setting No. displays and “
” flashes at the room temperature display, communication is probably abnormal.
Make sure there are no noise sources near the transmission line.
9 To select more functions, repeat steps 3 to 8.
? End function selection.
Press and hold down the A [FILTER] and B [TEST] buttons at the same time for two seconds or longer.
After a while, the function selection display disappears and the remote controller returns to the air conditioner off display.
* Do not operate the air conditioner from the remote controller for 30 seconds after the end of function selection.
NOTE: When the functions of an indoor unit were changed by function selection after the end of installation, always indicate the set contents
by entering a 嘷 or other mark in the appropriate check field of Table 1.
7
Self check
2 Set the address or refrigerant address No. you want to self check.
When the F [ TEMP. ( ) and ( )] buttons are pressed, the address
decreases and increases between 01 and 50 or 00 and 15. Set it to the
address No. or refrigerant address No. you want to self check.
Approximately three seconds after the change operation, the self check refrigerant address changes from flashing to a steady light and self check begins.
3 Self check result display <Error history> (For the contents of the error code, refer to the indoor unit installation manual or service handbook.)
ERROR CODE
Address 3 digits or unit address No. 2 digits
Error code 4 digits or error code 2 digits
<When opposite side does not exist>
<When there is no error history>
ERROR CODE
ERROR CODE
4 Error history reset
The error history is displayed in 3 Self check results display.
ERROR CODE
ERROR CODE
When the D [ MENU] button is pressed twice successively within three
seconds, the self check address or refrigerant address flashes.
Object unit address No.
Unit address No. 00
When the error history was reset, the display shown below appears.
When error history reset failed, the error contents are displayed again.
ERROR CODE
5 Self check reset
There are the following two ways of resetting self check.
Press the H [CHECK] button twice successively within three seconds → Resets self check and returns to the state before self check.
Press the I [ ON/OFF] button → Self check resets and indoor units stop.
(When operation is prohibited, this operation is ineffective.)
These items are set for all indoor units.
8
Unit address No. 01 to 04 or
AL
Remote Controller Check
When the air conditioner cannot be controlled from the remote controller,
use this function to check the remote controller.
1 First check the power mark.
When normal voltage (DC12V) is not applied to the remote controller,
the power mark goes off.
When the power mark is off, check the remote controller wiring and
the indoor unit.
2 Switch to the remote controller check mode.
When the H [CHECK] button is held down for five seconds or
longer, the display shown below appears.
These items are set for each
indoor unit.
3 Remote controller check result
When remote controller is normal
[Function selection flow]
First grasp the function selection flow. The following describes setting of “Room temperature detection position” of Table 1 as an example.
(For the actual setting procedure, see [Setting procedure] 1 to ?.)
Since there is no problem at the remote controller, check for other causes.
When the problem is other than the checked remote controller
(Error code 2) “E3” “6833” “6832” flash → Cannot send
1 Check the function selection set contents.
2 Switch to the FUNCTION SELECTION mode.
(Press A and B simultaneously in the remote controller OFF state.)
Power mark
When the A [FILTER] button is pressed, remote controller check begins.
When remote controller is faulty
(Error display 1) “NG” flashes → Remote controller send/receive circuit abnormal
NOTE: When the indoor unit functions were changed using the function selection after installation is complete, always indicate the set contents by
entering 嘷 or other mark in the appropriate check field of Table 1.
- Deletion error display
When deletion was not performed properly.
)] buttons.
Setting No. 3 = Remote controller built-in sensor
Setting No. 1 = Simultaneous operation indoor units balance
(3) Automatic cooling/heating display setting
• To switch the setting, press the [ ON/OFF] button.
1 ON : One of “Automatic cooling” and “Automatic heating” is displayed
under the automatic mode is running.
2 OFF : Only “Automatic” is displayed under the automatic mode.
Check
) and (
Self check address or self check refrigerant address
(2) Suction air temperature display setting
• To switch the setting, press the [ ON/OFF] button.
1 ON : The suction air temperature is displayed.
2 OFF : The suction air temperature is not displayed.
Setting No.
1
2
1
2
3
1
2
3
1
2
1
2
3
1
2
3
1
2
1
2
1
2
3
1
2
1
2
TEMP. (
Setting No. display
7
[4] -4. Display change setting
(1) Temperature display °C/°F setting
• To switch the setting, press the [
ON/OFF] button.
1 °C: The temperature unit °C is used.
2 °F: The temperature unit °F is used.
Mode No.
01
01
02
02
02
03
03
03
05
05
07
07
07
08
08
08
09
09
10
10
11
11
11
12
12
13
13
Select the setting No. using the F [
Retrieve the error history of each unit using the remote controller.
1 Switch to the self check mode.
When the H [CHECK] button is pressed twice successively
within three seconds, the display shown below appears.
Perform only when change is necessary with Mr. SLIM air conditioner.
(Cannot be performed with CITY MULTI control system.)
Set the functions of each indoor unit from the remote controller, as required. The functions of each indoor unit can be selected only from the remote controller.
Set the functions by selecting the necessary items from Table 1.
Table 1. Function selection contents (For a detailed description of the factory settings and mode of each indoor unit, refer to the indoor unit installation manual.)
Humidifier
For taking cord out of top of
remote controller
Outdoor unit
I
FILTER
DAY
CLOCK
See [4]-4. (1)
Press the G button.
Suction air temperature display setting (“ROOM TEMP DISP SELECT”)
(3) Timer function setting
• To switch the setting, press the [ ON/OFF] button (Choose one of
the followings.).
1 WEEKLY TIMER (initial setting on MA deluxe):
The weekly timer can be used.
2 AUTO OFF TIMER: The auto off timer can be used.
3 SIMPLE TIMER (Default setting on MA smooth):
The simple timer can be used.
4 TIMER MODE OFF: The timer mode cannot be used.
* When the use of clock setting is OFF, the “WEEKLY TIMER” cannot be
used.
LOSSNAY connectivity
< 3. Deletion procedure >
Use this procedure when you want to delete registration of indoor units connected by the remote controller and LOSSNAY.
; Confirm (see 2. Confirmation procedure) the LOSSNAY you want to delete and display the indoor units and LOSSNAY confirmation results.
Seal around here
with putty.
Bushing
See [4]-3. (4)
(2) Use of clock setting
• To switch the setting, press the [ ON/OFF] button.
1 ON : The clock function can be used.
2 OFF : The clock function cannot be used.
Indoor temperature
detecting
Use surface
raceways
Remote control cord
Contact number setting for error situation (“CALL.”)
(2) Use of automatic mode setting
When the remote controller is connected to the unit that has automatic operation mode, the following settings can be made.
• To switch the setting, press the [ ON/OFF] button.
1 ON (Initial setting value) : The automatic mode is displayed when
the operation mode is selected.
2 OFF
: The automatic mode is not displayed
when the operation mode is selected.
Switch box two units
Seal the remote controller cord with putty in order to prevent the possible entry of dew, water droplets, cockroaches, other insects, etc.
When using the switch box
When installing directly on the wall
• When installing on the switch box, seal
• When opening a hole using a drill for the remote controller cord (or when taking the cord
the connections between the switch box
out of the back of the remote controller), seal the hole with putty.
and wiring pipe with putty.
• When routing the cord via the portion cut off from the upper cover, similarly seal that
portion with putty.
• When taking the remote controller cord from back of the controller, use surface raceWiring pipe
ways.
Wall
Lock nut
E
[4] -2. Function limit
(1) Operation function limit setting (operation lock)
• To switch the setting, press the [ ON/OFF] button.
1 no1 : Operation lock setting is made on all buttons other than
the [ ON/OFF] button.
2 no2 : Operation lock setting is made on all buttons.
3 OFF (Initial setting value): Operation lock setting is not made.
* To make the operation lock setting valid on the normal screen, it is
necessary to press buttons (Press and hold down the [FILTER]
and [ ON/OFF] buttons at the same time for two seconds.) on
the normal screen after the above setting is made.
AUTO mode
2.
See [4]-3. (3)
TEMP.
(2) Unit Function Selection
Cannot be registered because the registered indoor unit or LOSSNAY does not exist.
Cannot be registered because another LOSSNAY was registered at the registered indoor unit.
MENU] button and confirm the LOSSNAY address registered at the set indoor unit address.
9 Press the [
- Confirmation end display (When LOSSNAY is connected.)
The indoor unit address and “IC” and registered LOSSNAY address and “LC” are alternately displayed.
10
20
15 or less
Timer function setting (“WEEKLY TIMER”)
(4) Contact number setting for error situation
• To switch the setting, press the [ ON/OFF] button.
1 CALL OFF: The set contact numbers are not displayed in case of error.
2 CALL **** *** **** : The set contact numbers are displayed in case
of error.
<Indoor unit address>
7
F
See [4]-3. (2)
[Detailed setting]
[4] -1. CHANGE LANGUAGE setting
The language that appears on the dot display can be selected.
• Press the [ MENU] button to change the language.
1 Japanese (JP), 2 English (GB), 3 German (D), 4 Spanish (E),
5 Russian (RU), 6 Italian (I), 7 Chinese (CH), 8 French (F)
Function
Power failure automatic
recovery
φ6
73
83.5±0.4
102
20
20
φ6
30
)]
- Registration error display
If the address was not correctly registered, the indoor unit address and registered LOSSNAY address are alternately displayed.
NOTE: Make sure that there is no wiring or wire near the remote controller sensor. If there is, the remote controller cannot detect the exact room
temperature.
30
) and (
Temperature
sensor
When a remote controller temperature sensor is used in a place which is likely to be affected by the wall on which the remote controller is
installed, use of an optional spacer (Model: PAC-YT83RS) for a remote controller is recommended.
(For how to set the main and sub remote controller, see step (1) “Remote controller” [4]-3. (1) in section 6 Function Selection .
For how to set the temperature sensor, see step (2) ”Unit function selection” in section 6 Function Selection .)
(2) When installing on either the switch box or the wall, allow extra space around the remote controller as shown in the figure at the right.
(3) Parts which must be supplied on site.
• Switch box for two units
• Thin-copper wiring pipe
• Lock nut and bushing
• Surface raceways
TEMP. (
30 mm
CAUTION The place where (when) the difference between the room temperature and the wall temperature is large, the wall temperature that is affected by the temperature of the wall on
which the remote controller is installed is measured. Therefore, the difference between
the room temperature and the measured wall temperature may be large.
When the installation site is one of the followings, use of a temperature sensor for an
indoor unit is recommended.
- When the room is not well-ventilated and the air does not reach the wall on which the
remote controller is installed.
- When the difference between the temperature of the wall on which the remote controller is installed and the room temperature.
- When the backside of the wall on which the remote controller is installed is exposed
to the outdoor air.
When the temperature changes drastically, the temperature may not be measured accurately.
Refrigerant address 00
* When “
” flashes at the room temperature display, the selected refrigerant address is not in the system.
When “F” is displayed at the unit address No. display, and when it flashes
together with the refrigerant address display, the selected unit address
No. does not exist. Correctly set the refrigerant address and unit address No. by repeating steps 2 and 3.
Mode No. 02 = Room temperature detection position
Perform this operation when you want to register the LOSSNAY, confirm the registered units, or delete the registered units controlled by the remote controller.
The following uses indoor unit address 05 and LOSSNAY address 30 as an example to describe the setting procedure.
Do not touch any control button with your wet hands.
Doing so may cause an electric shock or a malfunction.
Completely seal the wire lead-in port with putty etc.
Any dew, moisture, insects entering the unit may cause an electric shock or a
malfunction.
See [4]-3. (1)
Use of clock setting (“CLOCK”)
→ Temperature display °C/°F setting (“TEMP MODE °C/°F”)
Mode No. display
See [4]-2. (2)
Press the G button.
When registered using the E [
] button, the registered indoor
unit begins fan operation. When you want to know the location of the
indoor units of the unit address No. whose functions were selected, check
here. When the unit address No. is 00 or AL, all the indoor units of the
selected refrigerant address perform the fan operation.
Ex) When refrigerant address 00, unit address No. = 02 registered
5 Refrigerant address and unit address No. registration
Press the E [
] button. The refrigerant address and unit address No. are registered.
After a while, the mode No. display “– –” flashes.
NOTE: When using LOSSNAY units in conjunction, interlock the addresses of all indoor units within the group and address of LOSSNAY units.
Use standard wires in compliance with the current capacity.
A failure to this may result in an electric leakage, heating or fire.
Wire so that it does not receive any tension.
Tension may cause wire breakage, heating or fire.
Make this setting only when interlocked operation with LOSSNAY is necessary with CITY MULTI
models.
(This setting cannot be made with Mr. SLIM air conditioners.)
* When the upper controller is connected, make the setting using the upper controller.
Do not install in any place where acidic or alkaline solution or special
spray are often used.
Doing so may cause an electric shock or malfunction.
When installing the remote controller in a hospital or communication
facility, take ample countermeasures against noise.
Inverters, emergency power supply generators, high-frequency medical equipment, and wireless communication equipment can cause the remote controller to malfunction or to fail. Radiation from the remote controller may effect
communication equipment and prevent medial operations on the human body
or interfere with image transmission and cause noise.
Ventilation Setting
* When setting mode 1 to 3, set the unit address No. to “00”.
* When setting modes 7 to 11:
- When setting for each indoor unit, set the unit address No. to “01-04”.
- When batch setting for all indoor units, set the unit address No. to “AL”.
Dot display
The language that is selected in
CHANGE LANGUAGE mode
appears on this display. English
is set in this manual.
See [4]-2. (1)
When the C [ CLOCK ( ) and ( )] buttons are pressed, the unit address No. changes in 00 → 01 → 02 → 03 → 04 → AL order. Set it to the
unit address No. of the indoor unit whose functions you want to set.
Unit address No. display
See [4]-2. (3)
Press the
D button.
→ →
Do not apply AC100V or AC200V to the remote controller. The maximum
voltage that can be applied to the remote controller is 12V.
The remote controller may be damaged or may generate heat and cause a
fire.
Press the
D button.
Temperature range limit setting (“LIMIT TEMP FUNCTION”)
→ Remote controller main/sub setting (“CONTROLLER MAIN/SUB”)
ON/OFF
Stop test run by pressing the [
MENU
Press the G button.
Use of automatic mode setting (“SELECT AUTO MODE”)
G button.
Press the Press the
E button. E button.
˚C
TEMP.
→ Operation function limit setting (“LOCKING FUNCTION”)
Function limit
(“FUNCTION
SELECTION”) Press the
CAUTION
Do not install in any place exposed to flammable gas leakage.
Flammable gases accumulated around the body of PAR-21MAA may cause
an explosion.
See [4]-1
Item 3
(Setting content)
” have flashes for two seconds,
NOTE: If you make a mistake during operation, end function selection by step ? and repeat selection from step 2.
4 Set the indoor unit address No.
Press the D [ ON/OFF] button. The unit address No.
display “– –” flashes.
Remote Controller Function
Selection Mode
Press the G button.
Change Language
(“CHANGE LANGUAGE”)
→ → →
Ensure that installation work is done correctly following this installation manual.
Any deficiency caused by installation may result in an electric shock or fire.
* If the remote controller enters the OFF state after the “FUNCTION SELECTION” and room temperature displays “
communication is probably abnormal. Make sure there are no noise sources near the transmission line.
NOTE
Timer operation stops when the display
for remote controller function selection is
changed to the normal one.
(Hold down the E button and press
the D button for two seconds.)
* The remote controller records the
setting that is made in this way.
→ →
Ask your dealer or technical representative to install the unit.
Any deficiency caused by your own installation may result in an electric shock
or fire.
Refrigerant address
display
Normal display (Display when
the air condition is not running)
First, hook the cover to the two upper claws and then fit it to the remote controller.
WARNING
(1) Operation function limit setting (operation lock) (“LOCKING FUNCTION”)
(2) Use of automatic mode setting (“SELECT AUTO MODE”)
(3) Temperature range limit setting (“LIMIT TEMP FUNCTION”)
(1) Remote controller main/sub setting (“CONTROLLER MAIN/SUB”)
[Function selection flowchart]
[1] Stop the air conditioner to start remote controller function selection mode. → [2] Select from item1. → [3] Select from item2. → [4] Make the setting.
(Details are specified in item3) → [5] Setting completed. → [6] Change the display to the normal one. (End)
To remove the cover, insert a minus
screwdriver into one of the open
slots, and move it in the direction of
the arrow shown in the figure.
This symbol denotes what could lead to a personal injury or damage to your property if you misuse the PAR-21MAA.
Item 3 (Setting content)
• Display in multiple languages is possible.
Language setting to display
• Setting the range of operation limit (operation lock)
• Setting the use or non-use of “automatic” operation mode
• Setting the temperature adjustable range (maximum, minimum)
• Selecting main or sub remote controller
* When two remote controllers are connected to one group, one controller must be set to sub.
• Setting the use or non-use of clock function
(2) Use of clock setting (“CLOCK”)
• Setting the timer type
(3) Timer function setting (“WEEKLY TIMER”)
• Contact number display in case of error
(4) Contact number setting for error situation (“CALL.”)
• Setting the telephone number
• Setting the temperature unit (°C or °F) to display
(1) Temperature display °C/°F setting (“TEMP MODE °C/°F”)
4. Display change
(“DISP MODE SETTING”) (2) Suction air temperature display setting (“ROOM TEMP DISP SELECT”) • Setting the use or non-use of the display of indoor (suction) air temperature
(3) Automatic cooling/heating display setting (“AUTO MODE DISP C/H”) • Setting the use or non-use of the display of “Cooling” or “Heating” display during operation
with automatic mode
AB
This instruction manual describes how to install the MA Remote Controller for Mitsubishi Building Air Conditioning System, direct expansion type CITY
MULTI air conditioner indoor units (“-A” type and later), and Mitsubishi Mr. SLIM packaged air conditioners. Please read this manual thoroughly and
install the remote controller accordingly. For information on how to wire and install the air conditioning units, refer to the installation manual. After the
installation, hand over this manual to users.
Item 2
Item 1
1. Change Language
(“CHANGE LANGUAGE”)
2. Function limit
(“FUNCTION SELECTION”)
3. Mode selection
(“MODE SELECTION”)
To connect the
remote control cord,
peel 6mm of coating.
There is no polarity.
Installation Manual
WARNING
CAUTION
(1) Function selection of remote controller
The setting of the following remote controller functions can be changed using the remote controller function selection mode. Change the setting
when needed.
Connect the remote control cord to the remote controller terminal block.
PAR-21MAA
[Procedure] (Set only when change is necessary.)
1 Check the set contents of each mode. When the set contents of a mode were changed by function selection, the functions of that mode also change.
Check the set contents as described in steps 2 to 7 and change the setting based on the entries in the Table 1 check field. For the factory settings, refer to the indoor unit installation manual.
2 Set the remote controller to Off.
3 Set the outdoor unit refrigerant address No.
Press and hold down the A [FILTER] and B [TEST] buttons at
When the C [ CLOCK ( ) and ( )] buttons are pressed, the refrigerant
the same time for two seconds or longer.
address No. decreases and increases between 00 and 15. Set it to the
“FUNCTION SELECTION” blinks for a while, then the remote conrefrigerant address No. whose function you want to select.
troller display changes to the display shown below.
(This step is unnecessary for single refrigerant system.)
Function Selection
Remote controller switching is necessary.
(Error display 3) “ERC” and data error count are displayed → Data error generation
ERROR CODE
F
3 Refrigerant address specification → 00 (Outdoor unit specification)
(Unnecessary for single refrigerant system.)
CAUTION Do not turn the screwdriver in the slot. Doing so may damage the slot.
4.
Install the lower case on the switch box or directly on the wall.
When using the switch box
Switch box for two units
Seal the remote control cord
lead-in hole with putty.
(See 2 above)
WT04465X01_en_A1
1
Remote control cord
(See 5 below)
4 Unit address No. specification
(Buttons C and D operation)
5 Registration (Press button E.)
When installing directly on the wall
Cross recessed pan
head screw
Remote control cord
(See 5 below)
Wood screw
TEMP.
→ 00 (Indoor unit specification)
(Specified indoor unit →
Fan operation)
6 Mode No. Selection → 02 (Room temperature detection position)
YES
2
4
End?
NO
Change
refrigerant
address and unit
address No.?
MONITOR/SET
ON/OFF
DAY
CLOCK
G
FILTER
There is noise on the transmission line, or the indoor unit or another
remote controller is faulty. Check the transmission line and the other
remote controllers.
I
A
CHECK TEST
OPERATION
CLEAR
B
When data error count is 02
H
C
“Data error count” is the difference between the number of bits of remote controller
send data and the number of bits actually sent to the transmission line. In this
case, the send data was disturbed by the noise, etc. Check the transmission line.
Remote controller send data
Send data on transmission line
D
4 Remote controller check reset
When the H [CHECK] button is held down for five seconds or longer, remote controller check resets and the “PLEASE WAIT” and RUN lamp
flash. Approximately 30 seconds later, the remote controller returns to the state before remote controller check.
9
NO
YES
? Ending function display (Press buttons A and B simultaneously.)
04.11.10, 7:44 PM
BACK
PAR-21MAA
7 Setting No. selection → 3 (remote controller fixed)
(Buttons F and G operation)
8 Register (Press button E.)
E
MENU
ON/OFF
6
8