Avenview W-HDM3D5G-20M-KIT Specifications

AV Connectivity, Distribution And Beyond...
VIDEO WALLS VIDEO PROCESSORS
VIDEO MATRIX SWITCHES
EXTENDERS SPLITTERS WIRELESS
CABLES & ACCESSORIES
Wireless 5G HDMI Transmitter & Receiver
With 1080p and 3D compatible
Model #: W-HDM3D5G-50M
© 2013 Avenview Inc. All rights reserved.
The contents of this document are provided in connection with Avenview Inc. (“Avenview”) products. Avenview makes no representations or
warranties with respect to the accuracy or completeness of the contents of this publication and reserves the right to make changes to specifications
and product descriptions at any time without notice. No license, whether express, implied, or otherwise, to any intellectual property rights is granted
by this publication. Except as set forth in Avenview Standard Terms and Conditions of Sale, Avenview assumes no liability whatsoever, and disclaims
any express or implied warranty, relating to its products of Avenview Inc. is strictly prohibited.
TABLE OF CONTENTS
1
GETTING STARTED...........................................................................................................................1
1.1 Important Safeguards...............................................................................................................1
1.2 Safety Instructions...................................................................................................................1
1.3 Regulatory Notices Federal Communications Commission (FCC)............................ 2
2.INTRODUCTION...............................................................................................................................3
2.1PACKAGE CONTENTS......................................................................................................................4
2.2 BEFORE INSTALLATION....................................................................................................................4
2.3 APPLICATION DIAGRAM...................................................................................................................5
3.PANEL DESCRIPTION........................................................................................................................6
INPUT PANEL (Transmitter, W-HDM3D-50M-S)...............................................................................6
INPUT PANEL (Receiver, W-HDM3D-50M-R)...................................................................................6
4.
INSTALLATION (W-HDM3D5G-50M)...............................................................................................7
5.
IR REMOTE FUNCTIONS (W-HDM3D5G-50M)...............................................................................8
6.
ADD OR DELETE TRANSMITTER.....................................................................................................9
Add a wireless transmitter...................................................................................................................9
Select a wireless transmitter..............................................................................................................10
Delete a wireless transmitter:............................................................................................................10
7.
GENERAL TROUBLESHOOTING....................................................................................................11
8.SPECIFICATIONS..............................................................................................................................12
www.avenview.com
Page
2
1GETTING STARTED
SECTION 1: GETTING STARTED
1.1 Important Safeguards
Please read all of these instructions carefully before you use the device. Save this manual for future reference.
What the warranty does not cover
•• Any product, on which the serial number has been defaced, modified or removed.
•• Damage, deterioration or malfunction resulting from:
•• Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product modification, or failure
to follow instructions supplied with the product.
•• Repair or attempted repair by anyone not authorized by us.
•• Any damage of the product due to shipment.
•• Removal or installation of the product.
•• Causes external to the product, such as electric power fluctuation or failure.
•• Use of supplies or parts not meeting our specifications.
•• Normal wear and tear.
•• Any other causes which does not relate to a product defect.
•• Removal, installation, and set-up service charges.
1.2 Safety Instructions
The Avenview W-HDM3D5G-50M, Wireless Extender has been tested for conformity to safety regulations and requirements,
and has been certified for international use. However, like all electronic equipment’s, the W-HDM3D5G-50M should be used
with care. Read the following safety instructions to protect yourself from possible injury and to minimize the risk of damage to
the unit.
! Do not dismantle the housing or modify the module.
! Dismantling the housing or modifying the module may result in electrical shock or burn.
! Refer all servicing to qualified service personnel.
! Do not attempt to service this product yourself as opening or removing housing may expose you to dangerous
voltage or other hazards
! Keep the module away from liquids.
! Spillage into the housing may result in fire, electrical shock, or equipment damage. If an object or liquid falls or spills
on to the housing, unplug the module immediately.
! Have the module checked by a qualified service engineer before using it again.
! Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to the device before cleaning.
www.avenview.com
Page
1
1.3 Regulatory Notices Federal Communications Commission (FCC)
This equipment has been tested and found to comply with Part 15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation.
Any changes or modifications made to this equipment may void the user’s authority to operate this equipment.
Warning symbols
Description
ONLY USE THE PROVIDED POWER CABLE OR POWER
ADAPTER SUPPLIED. DO NOT TAMPER WITH THE
ELECTRICAL PARTS. THIS MAY RESULT IN ELECTRICAL
SHOCK OR BURN.
DO NOT TAMPER WITH THE UNIT. DOING SO WILL
VOID THE WARRANTY AND CONTINUED USE OF THE
PRODUCT.
THE VIDEO BOARDS ARE VERY SENSITIVE TO STATIC.
PLEASE ENSURE IF RACK MOUNTED OR INSTALLED ON A
SURFACE, IT SHOULD BE IN A GROUNDED ENVIROMENT.
www.avenview.com
Page
2
2.INTRODUCTION
W-HDM3D5G-50M, wireless extender set runs at 5GHz operation frequency to deliver HD video/audio 50 meters in open
field. This device kit make wireless connection by using WHDI Technology from HD media Source Devices such as HD Disc
or content player, PC, Game Console or Set-to –Box to any display Device for example LCD, Plasma or LED TV or projector.
Providing outstanding and consistent picture quality equivalent to wired HDMI™ cable, with low latency, multi-room connection
and low power consumption.
-----------
WHDI Technology no latency
5.8Ghz automatic channel switching system
Extends HDMI video and audio up to 50M (open Space)
Supports HDMI, EDID 1.1, Support HDCP 2.0
Supports resolution up to 3D supported HDTV / 1080Pp/60Hz, Vesa (1920 x 1080)
Support AES 128 image encryption
Real time compression audio is embedded within the HDMI output stream
Suitable for use with Residential, PC presentations
Extends IR and CEC Signals for remote control of AV Equipment
Supporting the point to point transmission function currently which can be expanded to the multi-point to point
transmission function.
www.avenview.com
Page
3
2.1PACKAGE CONTENTS
Before you start the installation of W-HDM3D5G-50M, please check package contents.
1
Wireless Transmitter
Wireless receiver
x1
x1
2
Power Adapter (5VDC)
x2
3
Remote Control
x1
4
2 X HDMI Cable & 1 X IR Cable
5
User’s Manual
x1
2.2 BEFORE INSTALLATION
•• Put the product in an even and stable location. If the product falls down or drops, it may cause an injury or malfunction.
•• Don’t place the product in too high temperature (over 50°C), too low temperature (under 0°C) or high humidity.
•• Use the DC power adapter with correct specifications. If inappropriate power supply is used then it may cause a fire.
•• Do not twist or pull by force ends of the HDMI cable. It can cause malfunction.
www.avenview.com
Page
4
2.3 APPLICATION DIAGRAM
It is ideal when your media player is located in your living room, while you want to watch your Full HD Movies on Your LCD,
Plasma or LED display device in your bedroom. You can install the Wireless HD Transmitter and Receiver Kit and let the wireless
transmission do the work via the WHDI Technology. Furthermore, you can operate the media player with the original remote
control in your bedroom.
The Wireless Extender can be used horizontal or vertical mode, depending on your requirement; however for optimum
performance is it recommended to operate in vertical mode. To use the extender in vertical mode simply use the base supplied
with the unit.
•
ach transmitter and receiver after pairing support only point to point operation. It cannot
E
support signals broadcasting by wireless.
•
Important before starting the insulation please ensure that all devices are powered off
www.avenview.com
Page
5
3.PANEL DESCRIPTION
INPUT PANEL (Transmitter, W-HDM3D-50M-S)
INPUT PANEL (Receiver, W-HDM3D-50M-R)
www.avenview.com
Page
6
4. INSTALLATION (W-HDM3D5G-50M)
To setup Avenview W-HDM3D5G-50M please follow these steps for connecting to a device:
1. Place the Transmitter unit in close proximity to the HDMI source device.
2. Connect the HDMI source device to HDMI IN port of the Transmitter by using a standard HDMI cable.
3. Connect the IR Extension cable to the port on the transmitter unit.
4. Place the other end of the IR Extension cable near the IR port on the HDMI source device.
5. Place the Receiver unit near your HDMI display/projector, Connect the HDMI display /projector to the HDMI Output
port of the Receiver unit.
6. Connect the power adapter (included) to the DC IN ports of the Transmitter and Receiver.
Once these steps have been completed the Extender is ready to use, simply power on all devices to begin operation.
Once all equipments are powered on, it is shown by the blue link LED (refer to table below). Then system will initiate a wireless
link, successful connection of the link will be shown by the blue link LED (refer to table below). This may take short time
depending on the distance between the units and other environmental factors.
When the initial wireless link has been established, the system will establish a video link between the transmitter and receiver.
Once it has been completed, the blue video LED will be lit on both units (refer to below table *). If your HDMI source and
display devices support CEC then your source device can simply to control using the displays remote control.
LED STATUS
Description
Link LED Slow Blink (TX, RX)
Power on
Link LED Fast Blink (TX, RX)
Establishing link
Link LED Steady ON (TX, RX)
Established link
Video LED Steady ON (TX, RX) *
Established video link
www.avenview.com
Page
7
5. IR REMOTE FUNCTIONS (W-HDM3D5G-50M)
BUTTON
DESCRIPTION
REG
REGISTRATION (to add a wireless transmitter)
MENU
ENTER Setup Mode
EXIT
EXIT Setup Mode
SOURCE
Transmitter LIST
ADD
Searching and adding a new Wireless Transmitter
OK
Enter or Confirm Function
INPUT 123
Change source 1,2,3

MENU/Character Selection
www.avenview.com
Page
8
6. ADD OR DELETE TRANSMITTER
Step1. Point the IR Remote control to Transmitter.
Press the MENU button on the IR remote, the OSD Menu will display on your display attached to the Receiver.
Wireless HDMI receiver unit (RX) menu
You can choose “Modify Video Source Name” to change existing transmitter’s name with  buttons.
Add a wireless transmitter
1. Press ADD button of the IR remote pointing to the Receiver unit, OSD Menu on display shows
2. Press and hold REG button of the IR remote pointing to the Transmitter until link LED flicker “Fast”.
OSD Menu on Display
Press OK button on the IR remote pointing to the Receiver unit.
www.avenview.com
Page
9
The word “TX” represents on the OSD menu the name of your transmitter.
OSD Menu on Display the link is successful.
Select a wireless transmitter
Press the SOURCE button pointing to the Receiver, the OSD menu shows on display
Use  buttons to select a Transmitter using the IR Remote pointing to the Receiver, and then press the OK button.
Delete a wireless transmitter:
Press DELETE button, the OSD menu on the display will show,
Use  buttons to select a Transmitter using the IR Remote pointing to the Receiver, and then press the OK button
www.avenview.com
Page
10
7. GENERAL TROUBLESHOOTING
PROBLEM
POSSIBLE SOLUTION
THE WIRELESS OR VIDEO
LINK LED IS NOT LIT
•• If the transmitter and /or Receiver are positioned horizontally
move the units to vertical position. Power cycle both extender
units (OFF 30 sec then ON).
•• Reduce the distance between the Transmitter and Receiver units.
Power cycle both extender units
•• (OFF 30 sec then ON).
MENU
•• Re-check all connections and verify they are in the correct
positions and verify the units are powered.
•• Check that the wireless and Video Link LEDs are LIT
EXIT
•• Check the IR Extender cable is connected to the Transmitter unit
•• Check that the IR EYE is visible and not being obstructed and the
transmission of IR from the remote can be sent.
•• Reposition the IR Flasher to another location near the IR port of
your source device
SOURCE
•• Reduce the distance (less than 1 meter) between the transmitter
and receiver units and then reconnect power adapter.
•• If no picture after Step 1, press REG button on IR remote pointing
towards the transmitter (don’t hold REG button).
•• If no picture after Step 1 and step 2, delete the source and re-add
the Transmitter.
www.avenview.com
Page
11
8.SPECIFICATIONS
Item
UNITS
UNIT DESCRIPTION
OPERATING FREQUENCY
Description
W-HDM3D5G-50M-S (Transmitter)
W-HDM3D5G-20M-S (Receiver)
WIRELESS Transmitter
WIRELESS Receiver
5.1GHz to 5.9 GHz
5.1GHz to 5.9 GHz
BANDWIDTH
MODULATION MODE
AUDIO FORMAT
SUPPORTED
DATA RATE
SUPPORTED RESOLUTION &
DISTANCE
HDMI CONNECTOR
ANTENNA
20Mhz/40Mhz
Downlink Channel: OFDM 16-QAM;
Uplink Channel: OFDM-OOK
I2S; PCM; SPDIF; AC-3; DTS; Dolby 5.1/7
Forward Channel: 3Gbps (400MBS)
HD: 480i, 480p, 576i, 576p, 720p, 1080i, 1080p
PC: VGA (640x480), SVGA (800x600), XGA (1024x768),
Monitor : 854x800, 1280x768, 1366x768, 1920x1080
HDMI FEMALE Plug (input)
HDMI FEMALE Plug (input)
High Performance Internal Antenna
IMAGE DELAY
<1ms
IR CMFS
38KHz
TRANSMISSION POWER
DIMENSIONS (L X W X H)
POWER SUPPLY
Power Output:10 ±2dBm
Power Output:15 ±2dBm
12” x 7” x 1”
12” x 7” x 1”
AC Input 100-240V,DC Output 5V
Environmental
OPERATING TEMPERATURE
STORAGE TEMPERATURE
RELATIVE HUMIDITY
32˚ ~ 104˚F (0˚ to 40˚C)
-4˚ ~ 140˚F (-20˚ ~ 60˚C)
20~90% RH (no condensation)
www.avenview.com
Page
12
Avenview Warranty Certificate
AVENVIEW CORP. (“Avenview”) warrants Avenview-branded product(s) contained in the original packaging against defects in materials and workmanship when used
normally in accordance with Avenview's enclosed manual guidelines for a period of THREE (3) YEARS from the date of original retail purchase - Warranty Period. Avenview’s
published guidelines include but are not limited to information contained in technical specifications, user manuals and service communications.
LABOR: During the Warranty Period of THREE (3) YEARS, Avenview will repair or replace the product(s) at no cost using new or used parts equivalent to novel performance
and reliability if the product(s) is determined to have abide by Avenview’s published guidelines. Cost of Labor applicable to product(s) after Warranty Period. For labor costs,
please contact support@avenview.com.
PARTS: During the Warranty Period of of THREE (3) YEARS, Avenview will supply new or rebuilt replacements in exchange for defective parts of the product(s) at no cost if
the product(s) is determined to have abide by Avenview’s published guidelines. Cost of Parts applicable to product(s) after Warranty Period. For part(s) costs, please contact
support@avenview.com.
To obtain Warranty: (a) proof of purchase in the form of a bill of sale or receipted invoice reflecting that the registered product(s) is within warranty period must be presented
to obtain warranty service; (b) product(s) must be registered at time of purchase. Failure to do so will result in applicable parts and labor charges. Returning product(s) must
be shipped in Avenview’s original packaging or in packaging pertaining equal degree of protection to Avenview’s. Both Avenview and purchaser are responsible for freight
charges and brokerages when shipping the product(s) to the receiver.
NOT COVERED BY THIS WARRANTY
This warranty does not apply to any non-Avenview branded product(s); non-registered Avenview product(s). This warranty does not apply: (a) to cosmetic damage, including
but not limited to scratches, dents and broken cords; (b) to damage caused by use with another product; (c) to damage caused by accident, abuse, misuse, liquid contact, fire,
earthquake or other external cause; (d) to damage caused by operating the Avenview product(s) outside Avenview’s manuals or guidelines; (e) to damage caused by service
performed by anyone who is not a representative of Avenview or an Avenview authorized personnel; (f) to defects caused by normal wear and tear or otherwise due to the
normal aging of the Avenview product(s), or (g) if any serial number has been removed or defaced from the Avenview product(s).
AVENVIEW IS NOT LIABLE FOR DIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM ANY BREACH OF WARRANTY OR
CONDITION, OR UNDER ANY OTHER LEGAL THEORY, INCLUDING BUT NOT LIMITED TO LOSS OF USE; LOSS OF REVENUE; LOSS OF ACTUAL OR
ANTICIPATED PROFITS (INCLUDING LOSS OF PROFITS ON CONTRACTS); LOSS OF THE USE OF MONEY; LOSS OF ANTICIPATED SAVINGS; LOSS OF BUSINESS;
LOSS OF OPPORTUNITY; LOSS OF GOODWILL; LOSS OF REPUTATION; LOSS OF, DAMAGE TO, COMPROMISE OR CORRUPTION OF DATA; OR ANY INDIRECT
OR CONSEQUENTIAL LOSS OR DAMAGE REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER.
Some states do not allow the inclusion or limitation of incidental or consequential damages, or allow limitations on duration implements of the Warranty Period; therefore the above limitations or
exclusions may not be applicable to you. This warranty gives you specific legal rights, and you may have other rights which vary from state to state.
275 Woodward Avenue, Kenmore, NY 14217
1.866.508.0269
www.avenview.com
Page
13
AV Connectivity, Distribution And Beyond...
TECHNICAL SUPPORT
Disclaimer
While every precaution has been taken in the preparation of this document, Avenview Inc. assumes no liability with respect to the operation or use of
Avenview hardware, software or other products and documentation described herein, for any act or omission of Avenview concerning such products or this
documentation, for any interruption of service, loss or interruption of business, loss of anticipatory profits, or for punitive, incidental or consequential damages
in connection with the furnishing, performance, or use of the Avenview hardware, software, or other products and documentation provided herein.
Avenview Inc. reserves the right to make changes without further notice to a product or system described herein to improve reliability, function or design.
With respect to Avenview products which this document relates, Avenview disclaims all express or implied warranties regarding such products, including but
not limited to, the implied warranties of merchantability, fitness for a particular purpose, and non-infringement.