INSTALLATION
MANUAL
SUNLINE MagnaDRY™
GAS/ELECTRIC SINGLE PACKAGE
AIR CONDITIONERS
CONTENTS
GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
MODELS: DR180, 240 & 300
SAFETY CONSIDERATIONS . . . . . . . . . . . . . . . . . . . . .4
INSPECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
REFERENCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
RENEWAL PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
APPROVALS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
PRODUCT NOMENCLATURE . . . . . . . . . . . . . . . . . . . .6
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53
START-UP (COOLING) . . . . . . . . . . . . . . . . . . . . . . . . .63
START-UP (GAS HEAT) . . . . . . . . . . . . . . . . . . . . . . . .64
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . .66
See the following pages for a complete Table of Contents.
NOTES, CAUTIONS AND WARNINGS
The installer should pay particular attention to the words:
NOTE, CAUTION, and WARNING. Notes are intended to
clarify or make the installation easier. Cautions are given
to prevent equipment damage. Warnings are given to
alert installer that personal injury and/or equipment damage may result if installation procedure is not handled
properly.
CAUTION: READ ALL SAFETY GUIDES BEFORE
YOU BEGIN TO INSTALL YOUR UNIT.
SAVE THIS MANUAL
127915-YIM-A-0405
127915-YIM-A-0405
TABLE OF CONTENTS
CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
GENERAL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
SAFETY CONSIDERATIONS . . . . . . . . . . . . . . . . . . . . . . . 4
INSPECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
REFERENCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
RENEWAL PARTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
APPROVALS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
PRODUCT NOMENCLATURE. . . . . . . . . . . . . . . . . . . . . . . 6
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
INSTALLATION SAFETY INFORMATION . . . . . . . . . . . 17
LIMITATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
LOCATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
RIGGING AND HANDLING . . . . . . . . . . . . . . . . . . . . . . 18
CLEARANCES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
DUCTWORK. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
FIXED OUTDOOR AIR INTAKE DAMPER . . . . . . . . . . 19
CONDENSATE DRAIN. . . . . . . . . . . . . . . . . . . . . . . . . . 20
COMPRESSORS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
FILTERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
SERVICE ACCESS . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
THERMOSTAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
POWER AND CONTROL WIRING. . . . . . . . . . . . . . . . . 22
OPTIONAL ELECTRIC HEAT . . . . . . . . . . . . . . . . . . . . 22
OPTIONAL GAS HEAT . . . . . . . . . . . . . . . . . . . . . . . . . 22
GAS PIPING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
GAS CONNECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
L.P. UNITS, TANKS AND PIPING . . . . . . . . . . . . . . . . . 24
VENT AND COMBUSTION AIR HOODS . . . . . . . . . . . . 25
OPTIONAL ECONOMIZER/MOTORIZED DAMPER
RAIN HOOD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
OPTIONAL POWER EXHAUST/BAROMETRIC
RELIEF DAMPER AND RAIN HOOD . . . . . . . . . . . . . 26
OPTIONAL ECONOMIZER AND POWER EXHAUST
DAMPER SETPOINT ADJUSTMENTS AND
INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
MINIMUM POSITION ADJUSTMENT . . . . . . . . . . . . . 26
ENTHALPY SETPOINT ADJUSTMENT . . . . . . . . . . . 26
POWER EXHAUST DAMPER SETPOINT (WITH
OR WITHOUT POWER EXHAUST) . . . . . . . . . . . . . . 26
INDOOR AIR QUALITY . . . . . . . . . . . . . . . . . . . . . . . . 26
CFM, STATIC PRESSURE, AND POWER - ALTITUDE
AND TEMPERATURE CORRECTIONS . . . . . . . . . . . . 38
PHASING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
CHECKING SUPPLY AIR CFM . . . . . . . . . . . . . . . . . . . 52
OPERATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
SEQUENCE OF OPERATIONS OVERVIEW. . . . . . . . . 53
COOLING SEQUENCE OF OPERATION . . . . . . . . . . . 53
CONTINUOUS BLOWER . . . . . . . . . . . . . . . . . . . . . . 53
INTERMITTENT BLOWER . . . . . . . . . . . . . . . . . . . . . 54
NO OUTDOOR AIR OPTIONS . . . . . . . . . . . . . . . . . . 54
ECONOMIZER WITH SINGLE ENTHALPY
SENSOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
ECONOMIZER WITH DUAL ENTHALPY SENSORS . 54
2
ECONOMIZER (SINGLE OR DUAL) WITH
POWER EXHAUST. . . . . . . . . . . . . . . . . . . . . . . . . . . 54
MOTORIZED OUTDOOR AIR DAMPERS . . . . . . . . . 55
COOLING OPERATION ERRORS . . . . . . . . . . . . . . . 55
HIGH-PRESSURE LIMIT SWITCH . . . . . . . . . . . . . . . 55
LOW-PRESSURE LIMIT SWITCH . . . . . . . . . . . . . . . 55
FREEZESTAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
LOW AMBIENT COOLING . . . . . . . . . . . . . . . . . . . . . 55
SAFETY CONTROLS . . . . . . . . . . . . . . . . . . . . . . . . . . 55
COMPRESSOR PROTECTION. . . . . . . . . . . . . . . . . . . 56
FLASH CODES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
RESET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
REHEAT MODE SEQUENCE OF OPERATION . . . . . . 56
“NORMAL” MODE. . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
"ALTERNATE” MODE . . . . . . . . . . . . . . . . . . . . . . . . . 56
ELECTRIC HEATING SEQUENCE OF
OPERATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
HEATING OPERATION ERRORS. . . . . . . . . . . . . . . . . 60
TEMPERATURE LIMIT . . . . . . . . . . . . . . . . . . . . . . . . 60
SAFETY CONTROLS . . . . . . . . . . . . . . . . . . . . . . . . . . 60
FLASH CODES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
RESET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
HEAT ANTICIPATOR SETPOINTS . . . . . . . . . . . . . . . . 60
GAS HEATING SEQUENCE OF OPERATIONS . . . . . . 61
GAS HEATING OPERATION ERRORS . . . . . . . . . . . . 62
TEMPERATURE LIMIT . . . . . . . . . . . . . . . . . . . . . . . . 62
GAS VALVE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
SAFETY CONTROLS . . . . . . . . . . . . . . . . . . . . . . . . . . 62
FLASH CODES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
RESETS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
HEAT ANTICIPATOR SETPOINTS . . . . . . . . . . . . . . . . 63
START-UP (COOLING) . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
PRESTART CHECK LIST . . . . . . . . . . . . . . . . . . . . . . . 63
OPERATING INSTRUCTIONS . . . . . . . . . . . . . . . . . . . 63
POST START CHECK LIST. . . . . . . . . . . . . . . . . . . . . . 63
SHUT DOWN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
START-UP (GAS HEAT) . . . . . . . . . . . . . . . . . . . . . . . . . . 64
PRE-START CHECK LIST. . . . . . . . . . . . . . . . . . . . . . . 64
OPERATING INSTRUCTIONS . . . . . . . . . . . . . . . . . . . 64
TO LIGHT PILOT AND MAIN BURNERS . . . . . . . . . . 64
TO SHUT DOWN . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
POST-START CHECK LIST (GAS) . . . . . . . . . . . . . . . . 64
MANIFOLD GAS PRESSURE ADJUSTMENT . . . . . . . 64
PILOT CHECKOUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
BURNER INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . 65
BURNER AIR SHUTTER ADJUSTMENT . . . . . . . . . . . 65
CHECKING GAS INPUT . . . . . . . . . . . . . . . . . . . . . . . . 65
NATURAL GAS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
ADJUSTMENT OF TEMPERATURE RISE . . . . . . . . . . 66
BELT DRIVE BLOWER . . . . . . . . . . . . . . . . . . . . . . . . . 66
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
COOLING TROUBLESHOOTING GUIDE . . . . . . . . . . . 66
GAS HEAT TROUBLESHOOTING GUIDE . . . . . . . . . . 70
UNIT FLASH CODES. . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Unitary Products Group
127915-YIM-A-0405
LIST OF FIGURES
Fig. #
1
LIST OF TABLES
Pg. #
Tbl. #
Pg. #
TYPICAL RIGGING . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
1
UNIT APPLICATION DATA. . . . . . . . . . . . . . . . . . . . . . .17
2
CENTER OF GRAVITY . . . . . . . . . . . . . . . . . . . . . . . . 18
2
CONTROL WIRE SIZES . . . . . . . . . . . . . . . . . . . . . . . . .22
3
FIXED OUTDOOR AIR DAMPER . . . . . . . . . . . . . . . . 20
3
ELECTRIC HEAT APPLICATION DATA . . . . . . . . . . . .22
4
RECOMMENDED DRAIN PIPING . . . . . . . . . . . . . . . 20
4
GAS HEAT APPLICATION DATA. . . . . . . . . . . . . . . . . .23
5
TYPICAL FIELD WIRING . . . . . . . . . . . . . . . . . . . . . . 21
5
PIPE SIZING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
6
EXTERNAL SUPPLY CONNECTION
EXTERNAL SHUT-OFF . . . . . . . . . . . . . . . . . . . . . . . 24
6
FOUR AND SIX POINT LOADS . . . . . . . . . . . . . . . . . . .28
7
PHYSICAL DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
7
BOTTOM SUPPLY CONNECTION
EXTERNAL SHUT-OFF . . . . . . . . . . . . . . . . . . . . . . . 24
8
DR ELECTRICAL DATA - STANDARD DRIVE
MOTOR W/O POWERED CONVENIENCE OUTLET . .30
8
VENT AND COMBUSTION AIR HOOD . . . . . . . . . . . 25
9
9
ENTHALPY SETPOINT ADJUSTMENT . . . . . . . . . . . 27
DR ELECTRICAL DATA - HIGH STATIC DRIVE
MOTOR W/O POWERED CONVENIENCE OUTLET . .31
10 HONEYWELL ECONOMIZER CONTROL W7212 . . . 27
11 FOUR AND SIX POINT LOADS . . . . . . . . . . . . . . . . . 28
12 DIMENSIONS & CLEARANCES 15/20/25 TON . . . . . 36
13 ALTITUDE/TEMPERATURE CONVERSION
FACTOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
14 CHARGING CHART - 15 TON . . . . . . . . . . . . . . . . . . 51
10 DR ELECTRICAL DATA - LOW AIRFLOW DRIVE
MOTOR W/O POWERED CONVENIENCE OUTLET . .32
11 DR ELECTRICAL DATA - STANDARD DRIVE
MOTOR WITH POWERED CONVENIENCE OUTLET .33
12 DR ELECTRICAL DATA - HIGH STATIC DRIVE
MOTOR WITH POWERED CONVENIENCE OUTLET .34
15 CHARGING CHART - 20 TON . . . . . . . . . . . . . . . . . . 51
13 DR ELECTRICAL DATA - LOW AIRFLOW DRIVE
MOTOR WITH POWERED CONVENIENCE OUTLET .35
16 CHARGING CHART - 25 TON . . . . . . . . . . . . . . . . . . 52
14 ALTITUDE CORRECTION FACTORS . . . . . . . . . . . . . .38
17 BELT ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . 52
15 DR180 BLOWER PERFORMANCE STANDARD DRIVE (COOLING ONLY) . . . . . . . . . . . . .40
18 PRESSURE DROP ACROSS A DRY
INDOOR COIL VS SUPPLY AIR CFM FOR
ALL UNIT TONNAGES . . . . . . . . . . . . . . . . . . . . . . . . 53
19 REHEAT CONTROL BOARD . . . . . . . . . . . . . . . . . . . 57
20 REHEAT CONTROLS - PART 1 . . . . . . . . . . . . . . . . . 58
21 REHEAT CONTROLS - PART 2 . . . . . . . . . . . . . . . . . 58
22 SYSTEM PIPING SCHEMATIC . . . . . . . . . . . . . . . . . 59
23 GAS VALVE PIPING . . . . . . . . . . . . . . . . . . . . . . . . . . 61
24 GAS VALVE AND CONTROLS. . . . . . . . . . . . . . . . . . 63
25 TYPICAL GAS VALVES . . . . . . . . . . . . . . . . . . . . . . . 64
26 PROPER FLAME ADJUSTMENT . . . . . . . . . . . . . . . . 65
27 TYPICAL FLAME APPEARANCE . . . . . . . . . . . . . . . . 65
16 DR180 BLOWER PERFORMANCE STANDARD DRIVE (GAS HEAT) . . . . . . . . . . . . . . . . . .41
17 DR180 BLOWER PERFORMANCE HIGH STATIC DRIVE (COOLING ONLY). . . . . . . . . . . .42
18 DR180 BLOWER PERFORMANCE HIGH STATIC DRIVE (GAS HEAT) . . . . . . . . . . . . . . . .43
19 DR240 BLOWER PERFORMANCE STANDARD DRIVE (COOLING ONLY) . . . . . . . . . . . . .44
20 DR240 BLOWER PERFORMANCE STANDARD DRIVE (GAS HEAT) . . . . . . . . . . . . . . . . . .45
21 DR240 BLOWER PERFORMANCE HIGH STATIC DRIVE (COOLING ONLY). . . . . . . . . . . .46
22 DR240 BLOWER PERFORMANCE HIGH STATIC DRIVE (GAS HEAT) . . . . . . . . . . . . . . . .47
23 DR300 BLOWER PERFORMANCE STANDARD DRIVE. . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
24 DR300 BLOWER PERFORMANCE HIGH STATIC DRIVE . . . . . . . . . . . . . . . . . . . . . . . . . . .49
25 STATIC RESISTANCES . . . . . . . . . . . . . . . . . . . . . . . . .50
26 POWER EXHAUST PERFORMANCE . . . . . . . . . . . . . .50
27 BLOWER MOTOR AND DRIVE DATA . . . . . . . . . . . . . .50
28 LIMIT CONTROL SETTING . . . . . . . . . . . . . . . . . . . . . .60
29 ELECTRIC HEAT ANTICIPATOR SETPOINTS . . . . . . .61
30 LIMIT CONTROL SETTING . . . . . . . . . . . . . . . . . . . . . .63
31 GAS HEAT ANTICIPATOR SETPOINTS . . . . . . . . . . . .63
32 GAS RATE - CUBIC FEET PER HOUR . . . . . . . . . . . . .66
33 UNIT CONTROL BOARD FLASH CODES. . . . . . . . . . .73
34 REHEAT CONTROL BOARD FLASH CODES. . . . . . . .74
Unitary Products Group
3
127915-YIM-A-0405
35
GENERAL
FIRE OR EXPLOSION HAZARD
YORK Model DR units are either single package cooling units equipped with optional factory installed electric heaters, or single package gas-fired central heating
furnaces with cooling unit. Both are designed for outdoor installation on a rooftop or slab.
Failure to follow safety warnings exactly could
result in serious injury, death, or property damage.
- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or
any other appliance.
The units are completely assembled on rigid, permanently attached base rails. All piping, refrigerant
charge, and electrical wiring is factory installed and
tested. The units require electric power, gas connection, duct connections, installation of combustion air
inlet hood, flue gas outlet hoods and fixed outdoor air
intake damper (units without economizer or motorized
damper option only) at the point of installation.
- WHAT TO DO IF YOU SMELL GAS:
• Do not try to light any appliance.
• Do not touch any electrical switch; do not
use any phone in your building.
• Leave the building immediately.
• Immediately call your gas supplier from a
neighbor’s phone. Follow the gas supplier’s instructions.
• If you cannot reach the gas supplier, call
the fire department.
- Installation and service must be performed by
a qualified installer, service agency or the
gas supplier.
The supplemental electric heaters have nickel-chrome
elements and utilize single point power connection.
The gas-fired heaters have aluminized-steel or optional
stainless steel, tubular heat exchangers with spark
ignition with proven pilot. All gas heaters are shipped
from the factory equipped for natural gas use, but can
be field converted to L.P./Propane with Kit Model #
1NP0418.
SAFETY CONSIDERATIONS
Due to system pressure, moving parts and electrical
components, installation and servicing of air conditioning equipment can be hazardous. Only qualified,
trained, service personnel should install, repair, maintain or service this equipment.
Observe all precautions in the literature, on labels and
tags accompanying the equipment whenever working
on air conditioning equipment. Be sure to follow all
other safety precautions that apply.
Wear safety glasses and work gloves, and follow all
safety codes. Use a quenching cloth and have a fire
extinguisher available for all brazing operations.
4
INSPECTION
As soon as a unit is received, it should be inspected for
possible damage during transit. If damage is evident,
the extent of the damage should be noted on the carrier's freight bill. A separate request for inspection by
the carrier's agent should be made in writing. Refer to
Form 50.15-NM for additional information.
REFERENCE
Additional information on the design, installation, operation and service of this equipment is available in the
following reference forms:
•
035-19856-000 - Barometric Relief Damper
Accessory
Unitary Products Group
127915-YIM-A-0405
•
035-19854-000 - Economizer Damper
Accessory
•
035-08032-002 - Propane Conversion Accessory
(USA)
•
035-13073-001 - High Altitude Accessory (Natural
Gas)
•
035-08524-002 - High Altitude Accessory (Propane)
This product must be installed in strict compliance with the enclosed installation instructions
and any applicable local, state, and national
codes including, but not limited to, building,
electrical, and mechanical codes.
RENEWAL PARTS
Refer to York USER'S MAINTENANCE and SERVICE
INFORMATION MANUAL Part Number 035-19699001.
APPROVALS
Design certified by CSA as follows:
•
For use as a cooling unit only with or without
optional electric heat.
•
For use as a forced air furnace with cooling unit
•
For outdoor installation only.
•
For installation on combustible material.
•
For use with natural gas or propane gas.
Unitary Products Group
Improper installation may create a condition
where the operation of the product could cause
personal injury or property damage.
The installer should pay particular attention to the
words: NOTE, CAUTION and WARNING. Notes are
intended to clarify or make the installation easier. Cautions are given to prevent equipment damage. Warnings are given to alert installer that personal injury and/
or equipment damage may result if installation procedure is not handled properly.
5
6
Heat Type & Nominal Heat Capacity
C00 = Cooling Only. No field installed electric heat
Gas Heat Options
N24 = 240 MBH Output Aluminized Steel
N32 = 320 MBH Output Aluminized Steel, (15-25T Only)
S24 = 240 MBH Output Stainless Steel
S32 = 320 MBH Output Stainless Steel, (15-25T Only)
Electric Heat Options
E18 = 18 KW
E36 = 36 KW
E54 = 54 KW
E72 = 72 KW
Nominal Cooling Capacity - MBH
180 = 15 Ton
240 = 20 Ton
300 = 25 Ton
Product Identifier
R = R-22 Reheat Unit
Product Category
D = Air Cond., Single Package
Voltage
1 = 208/230-1-60
2 = 208/230-3-60
4 = 460-3-60
5 = 575-3-60
Product Generation
1 = First Generation
2 = Second Generation
Airflow
A = Std Motor/Drive
B = Std Mtr/Drive/Single Input Econo
C = Std Mtr/Drive/Single Input Econo/Power Exhaust
D = Std Mtr/Drive/Motorized Damper
F = Std Mtr/Drive/4" Filters
G = Std Mtr/Drive/4" Filters/Single Input Econ
H = Std Mtr/Drive/4" Filters/Single Input Econ/Power Exhaust
L = Std Mtr/Drive/BAS Ready Econ (No BAS Controller) w/2" Pleated Filters
M = Std Mtr/Drive/BAS Ready Econ (No BAS Controller)/Power Exhaust w/2" Pleated Filters
N = Hi Static Drive
P = Hi Static Drive/Single Input Econo
Q = Hi Static Drive/Single Input Econo/Power Exhaust
R = Hi Static Drive/Motorized Damper
T = Hi Static Drive/4" Filters
U = Hi Static Drive/4" Filters/Single Input Econ
V = Hi Static Drive/4" Filters/Single Input Econ/Power Exhaust
Y = Hi Static Drive/BAS Ready Econ (No BAS Controller) w/2" Pleated Filters
Z = Hi Static Drive/BAS Ready Econ (No BAS Controller)/Power Exhaust w/2" Pleated Filters
2 = Low Static Drive - 25 Ton only
3 = Low Static Drive/Single Input Econo - 25 Ton only
4 = Low Static Drive/Single Input Econo/Power Exhaust - 25 Ton only
5 = Low Static Drive/Motorized Damper - 25 Ton only
D R 300 N 24 A 2 A AA 1 A
York Brand
15 - 25T Sunline MagnaDRY™ Model Number Nomenclature
Installation Options
A = No Options Installed
B = Option 1
C = Option 2
D = Options 1 & 2
E = Option 3
F = Options 4
G = Options 1 & 3
H = Options 1 & 4
J = Options 1, 2 & 3
K = Options 1, 2, & 4
L = Options 1,3 & 4
M = Options 1, 2, 3, & 4
N = Options 2 & 3
P = Options 2 & 4
Q = Options 2, 3, & 4
R = Options 3 & 4
S = Option 5
T = Options 1 & 5
U = Options 1, 3, & 5
V = Options 1, 4, & 5
W = Options 1, 3, 4, & 5
X = Options 3 & 5
Y = Options 4 & 5
Z = Options 3, 4, & 5
Options
1 = Disconnect
2 = Non-Pwr'd Conv Oultet
3 = Smoke Detector S.A.
4 = Smoke Detector R.A.
5 = Pwr'd Conv. Outlet
Product Style
A = Style A
Additional Options
(See Next Page)
127915-YIM-A-0405
PRODUCT NOMENCLATURE
Unitary Products Group
127915-YIM-A-0405
PRODUCT NOMENCLATURE - CONTINUED
15-25T Sunline Magna DRY™ Model Number Nomenclature
Additional Options - Standard Cabinet
AA
AB
AC
AD
AE
AF
AG
AH
AJ
AK
AL
AM
AN
AP
AQ
AR
AT
AU
AV
AW
AX
AY
AZ
CA
CB
CC
CD
CE
CF
CG
CH
CJ
CK
CL
CM
CN
CP
CQ
CR
CS
CT
CU
CV
CW
CX
CY
CZ
C1
C2
C3
C4
None
Phase Monitor
Coil Guard
Dirty Filter Switch
Phase Monitor & Coil Guard
Phase Monitor & Dirty Filter Switch
Coil Guard & Dirty Filter Switch
Phase Monitor, Coil Guard, & Dirty Filter Switch
SS Drain Pan
SS Drain Pan & Phase Monitor
SS Drain Pan & Coil Guard
SS Drain Pan & Dirty Filter Switch
SS Drain Pan, Phase Monitor, Coil Guard & Dirty Filter Switch
Double Wall
Double Wall & Phase Monitor
Double Wall & Dirty Filter Switch
Double Wall & Coil Guard
Double Wall & Phase Monitor, Dirty Filter Switch & Coil Guard
Double Wall, SS Drain Pan
Double Wall & SS Drain Pan & Phase Monitor
Double Wall & SS Drain Pan & Coil Guard
Double Wall & SS Drain Pan & Dirty Filter Switch
Double Wall & SS Drain Pan & Phase Monitor, Coil Guard, Dirty Filter Switch
CPC Controller with Dirty Filter Switch & Air Proving Switch
CPC Controller, DFS, APS & Phase Monitor
CPC Controller, DFS, APS & Coil Guard
CPC Controller, DFS, APS, Phase Monitor, & Coil Guard
CPC Controller, DFS, APS & Technicoat Cond. Coil
CPC Controller, DFS, APS, Technicoat Cond. Coil, & Phase Monitor
CPC Controller, DFS, APS, Technicoat Cond. Coil, & Coil Guard
CPC Controller, DFS, APS, Technicoat Cond. Coil, Phase Monitor, & Coil Guard
CPC Controller, DFS, APS & Technicoat Evap. Coil
CPC Controller, DFS, APS, Technicoat Evap. Coil, & Phase Monitor
CPC Controller, DFS, APS, Technicoat Evap. Coil, & Coil Guard
CPC Controller, DFS, APS, Technicoat Evap. Coil, Phase Monitor, & Coil Guard
CPC Controller, DFS, APS & Technicoat Evap. & Cond Coils
CPC Controller, DFS, APS, Technicoat Evap. & Cond Coils, & Phase Monitor
CPC Controller, DFS, APS, Technicoat Evap. & Cond Coils, & Coil Guard
CPC Controller, DFS, APS, Technicoat Evap. & Cond Coils, Phase Monitor, & Coil Guard
CPC Controller, DFS, APS, SS Drain Pan
CPC Controller, DFS, APS, SS Drain Pan, Phase Monitor, & Coil Guard
CPC Controller, DFS, APS, SS Drain Pan, & Technicoat Cond Coils
CPC Controller, DFS, APS, SS Drain Pan, & Technicoat Evap Coil
CPC Controller, DFS, APS, SS Drain Pan, & Technicoat Evap and Cond Coils
CPC Controller, DFS, APS, SS Drain Pan, Phase Monitor, Coil Guard, & Technicoat Evap and Cond Coils
CPC Controller, DFS, APS, Double Wall
CPC Controller, DFS, APS, Double Wall, Phase Monitor, & Coil Guard
CPC Controller, DFS, APS, Double Wall, & Technicoat Cond Coils
CPC Controller, DFS, APS, Double Wall, & Technicoat Evap Coil
CPC Controller, DFS, APS, Double Wall, & Technicoat Evap and Cond Coils
CPC Controller, DFS, APS, Double Wall, Phase Monitor, Coil Guard, & Technicoat Evap and Cond Coils
Unitary Products Group
7
127915-YIM-A-0405
Additional Options - Standard Cabinet
C5
C6
C7
C8
C9
JA
JB
JC
JD
JE
JF
JG
JH
JJ
JK
JL
JM
JN
JP
JQ
JR
JS
JT
JU
JV
JW
JX
JY
JZ
J1
J2
J3
J4
J5
J6
J7
J8
J9
HA
HB
HC
HD
HE
HF
HG
HH
HJ
HK
HL
HM
HN
HP
HQ
HR
HS
HT
8
CPC Controller, DFS, APS, Double Wall, SS Drain Pan, Phase Monitor, & Coil Guard
CPC Controller, DFS, APS, Double Wall, SS Drain Pan, & Technicoat Cond Coils
CPC Controller, DFS, APS, Double Wall, SS Drain Pan, & Technicoat Evap Coil
CPC Controller, DFS, APS, Double Wall, SS Drain Pan, & Technicoat Evap and Cond Coils
CPC Controller, DFS, APS, Double Wall, SS Drain Pan, Phase Monitor, Coil Guard, & Technicoat Evap and Cond Coils
Johnson UNT Controller with Dirty Filter Switch & Air Proving Switch
Johnson UNT Controller, DFS, APS & Phase Monitor
Johnson UNT Controller, DFS, APS & Coil Guard
Johnson UNT Controller, DFS, APS, Phase Monitor, & Coil Guard
Johnson UNT Controller, DFS, APS & Technicoat Cond. Coil
Johnson UNT Controller, DFS, APS, Technicoat Cond. Coil, & Phase Monitor
Johnson UNT Controller, DFS, APS, Technicoat Cond. Coil, & Coil Guard
Johnson UNT Controller, DFS, APS, Technicoat Cond. Coil, Phase Monitor, & Coil Guard
Johnson UNT Controller, DFS, APS & Technicoat Evap. Coil
Johnson UNT Controller, DFS, APS, Technicoat Evap. Coil, & Phase Monitor
Johnson UNT Controller, DFS, APS, Technicoat Evap. Coil, & Coil Guard
Johnson UNT Controller, DFS, APS, Technicoat Evap. Coil, Phase Monitor, & Coil Guard
Johnson UNT Controller, DFS, APS & Technicoat Evap. & Cond Coils
Johnson UNT Controller, DFS, APS, Technicoat Evap. & Cond Coils, & Phase Monitor
Johnson UNT Controller, DFS, APS, Technicoat Evap. & Cond Coils, & Coil Guard
Johnson UNT Controller, DFS, APS, Technicoat Evap. & Cond Coils, Phase Monitor, & Coil Guard
Johnson UNT Controller, DFS, APS, SS Drain Pan
Johnson UNT Controller, DFS, APS, SS Drain Pan, Phase Monitor, & Coil Guard
Johnson UNT Controller, DFS, APS, SS Drain Pan, & Technicoat Cond Coils
Johnson UNT Controller, DFS, APS, SS Drain Pan, & Technicoat Evap Coil
Johnson UNT Controller, DFS, APS, SS Drain Pan, & Technicoat Evap and Cond Coils
Johnson UNT Controller, DFS, APS, SS Drain Pan, Phase Monitor, Coil Guard, & Technicoat Evap and Cond Coils
Johnson UNT Controller, DFS, APS, Double Wall
Johnson UNT Controller, DFS, APS, Double Wall, Phase Monitor, & Coil Guard
Johnson UNT Controller, DFS, APS, Double Wall, & Technicoat Cond Coils
Johnson UNT Controller, DFS, APS, Double Wall, & Technicoat Evap Coil
Johnson UNT Controller, DFS, APS, Double Wall, & Technicoat Evap and Cond Coils
Johnson UNT Controller, DFS, APS, Double Wall, Phase Monitor, Coil Guard, & Technicoat Evap and Cond Coils
Johnson UNT Controller, DFS, APS, Double Wall, SS Drain Pan, Phase Monitor, & Coil Guard
Johnson UNT Controller, DFS, APS, Double Wall, SS Drain Pan, & Technicoat Cond Coils
Johnson UNT Controller, DFS, APS, Double Wall, SS Drain Pan, & Technicoat Evap Coil
Johnson UNT Controller, DFS, APS, Double Wall, SS Drain Pan, & Technicoat Evap and Cond Coils
Johnson UNT Controller, DFS, APS, Double Wall, SS Drain Pan, Phase Monitor, Coil Guard, & Technicoat Evap and Cond Coils
Honeywell Excel 10 Controller with Dirty Filter Switch & Air Proving Switch
Honeywell Excel 10 Controller, DFS, APS & Phase Monitor
Honeywell Excel 10 Controller, DFS, APS & Coil Guard
Honeywell Excel 10 Controller, DFS, APS, Phase Monitor, & Coil Guard
Honeywell Excel 10 Controller, DFS, APS & Technicoat Cond. Coil
Honeywell Excel 10 Controller, DFS, APS, Technicoat Cond. Coil, & Phase Monitor
Honeywell Excel 10 Controller, DFS, APS, Technicoat Cond. Coil, & Coil Guard
Honeywell Excel 10 Controller, DFS, APS, Technicoat Cond. Coil, Phase Monitor, & Coil Guard
Honeywell Excel 10 Controller, DFS, APS & Technicoat Evap. Coil
Honeywell Excel 10 Controller, DFS, APS, Technicoat Evap. Coil, & Phase Monitor
Honeywell Excel 10 Controller, DFS, APS, Technicoat Evap. Coil, & Coil Guard
Honeywell Excel 10 Controller, DFS, APS, Technicoat Evap. Coil, Phase Monitor, & Coil Guard
Honeywell Excel 10 Controller, DFS, APS & Technicoat Evap. & Cond Coils
Honeywell Excel 10 Controller, DFS, APS, Technicoat Evap. & Cond Coils, & Phase Monitor
Honeywell Excel 10 Controller, DFS, APS, Technicoat Evap. & Cond Coils, & Coil Guard
Honeywell Excel 10 Controller, DFS, APS, Technicoat Evap. & Cond Coils, Phase Monitor, & Coil Guard
Honeywell Excel 10 Controller, DFS, APS, SS Drain Pan
Honeywell Excel 10 Controller, DFS, APS, SS Drain Pan, Phase Monitor, & Coil Guard
Unitary Products Group
127915-YIM-A-0405
Additional Options - Standard Cabinet
HU
HV
HW
HX
HY
HZ
H1
H2
H3
H4
H5
H6
H7
H8
H9
NA
NB
NC
ND
NE
NF
NG
NH
NJ
NK
NL
NM
NN
NP
NQ
NR
NS
NT
NU
NV
NW
NX
NY
NZ
N1
N2
N3
N4
N5
N6
N7
N8
N9
TA
TB
TC
TD
TE
TF
TG
TH
Honeywell Excel 10 Controller, DFS, APS, SS Drain Pan, & Technicoat Cond Coils
Honeywell Excel 10 Controller, DFS, APS, SS Drain Pan, & Technicoat Evap Coil
Honeywell Excel 10 Controller, DFS, APS, SS Drain Pan, & Technicoat Evap and Cond Coils
Honeywell Excel 10 Controller, DFS, APS, SS Drain Pan, Phase Monitor, Coil Guard, & Technicoat Evap and Cond Coils
Honeywell Excel 10 Controller, DFS, APS, Double Wall
Honeywell Excel 10 Controller, DFS, APS, Double Wall, Phase Monitor, & Coil Guard
Honeywell Excel 10 Controller, DFS, APS, Double Wall, & Technicoat Cond Coils
Honeywell Excel 10 Controller, DFS, APS, Double Wall, & Technicoat Evap Coil
Honeywell Excel 10 Controller, DFS, APS, Double Wall, & Technicoat Evap and Cond Coils
Honeywell Excel 10 Controller, DFS, APS, Double Wall, Phase Monitor, Coil Guard, & Technicoat Evap and Cond Coils
Honeywell Excel 10 Controller, DFS, APS, Double Wall, SS Drain Pan, Phase Monitor, & Coil Guard
Honeywell Excel 10 Controller, DFS, APS, Double Wall, SS Drain Pan, & Technicoat Cond Coils
Honeywell Excel 10 Controller, DFS, APS, Double Wall, SS Drain Pan, & Technicoat Evap Coil
Honeywell Excel 10 Controller, DFS, APS, Double Wall, SS Drain Pan, & Technicoat Evap and Cond Coils
Honeywell Excel 10 Controller, DFS, APS, Double Wall, SS Drain Pan, Phase Monitor, Coil Guard, & Technicoat Evap and Cond Coils
Novar ETC-3 Controller with Dirty Filter Switch & Air Proving Switch
Novar ETC-3 Controller, DFS, APS & Phase Monitor
Novar ETC-3 Controller, DFS, APS & Coil Guard
Novar ETC-3 Controller, DFS, APS, Phase Monitor, & Coil Guard
Novar ETC-3 Controller, DFS, APS & Technicoat Cond. Coil
Novar ETC-3 Controller, DFS, APS, Technicoat Cond. Coil, & Phase Monitor
Novar ETC-3 Controller, DFS, APS, Technicoat Cond. Coil, & Coil Guard
Novar ETC-3 Controller, DFS, APS, Technicoat Cond. Coil, Phase Monitor, & Coil Guard
Novar ETC-3 Controller, DFS, APS & Technicoat Evap. Coil
Novar ETC-3 Controller, DFS, APS, Technicoat Evap. Coil, & Phase Monitor
Novar ETC-3 Controller, DFS, APS, Technicoat Evap. Coil, & Coil Guard
Novar ETC-3 Controller, DFS, APS, Technicoat Evap. Coil, Phase Monitor, & Coil Guard
Novar ETC-3 Controller, DFS, APS & Technicoat Evap. & Cond Coils
Novar ETC-3 Controller, DFS, APS, Technicoat Evap. & Cond Coils, & Phase Monitor
Novar ETC-3 Controller, DFS, APS, Technicoat Evap. & Cond Coils, & Coil Guard
Novar ETC-3 Controller, DFS, APS, Technicoat Evap. & Cond Coils, Phase Monitor, & Coil Guard
Novar ETC-3 Controller, DFS, APS, SS Drain Pan
Novar ETC-3 Controller, DFS, APS, SS Drain Pan, Phase Monitor, & Coil Guard
Novar ETC-3 Controller, DFS, APS, SS Drain Pan, & Technicoat Cond Coils
Novar ETC-3 Controller, DFS, APS, SS Drain Pan, & Technicoat Evap Coil
Novar ETC-3, DFS, APS, SS Drain Pan, & Technicoat Evap and Cond Coils
Novar ETC-3 Controller, DFS, APS, SS Drain Pan, Phase Monitor, Coil Guard, & Technicoat Evap and Cond Coils
Novar ETC-3 Controller, DFS, APS, Double Wall
Novar ETC-3 Controller, DFS, APS, Double Wall, Phase Monitor, & Coil Guard
Novar ETC-3 Controller, DFS, APS, Double Wall, & Technicoat Cond Coils
Novar ETC-3 Controller, DFS, APS, Double Wall, & Technicoat Evap Coil
Novar ETC-3 Controller, DFS, APS, Double Wall, & Technicoat Evap and Cond Coils
Novar ETC-3 Controller, DFS, APS, Double Wall, Phase Monitor, Coil Guard, & Technicoat Evap and Cond Coils
Novar ETC-3 Controller, DFS, APS, Double Wall, SS Drain Pan, Phase Monitor, & Coil Guard
Novar ETC-3 Controller, DFS, APS, Double Wall, SS Drain Pan, & Technicoat Cond Coils
Novar ETC-3 Controller, DFS, APS, Double Wall, SS Drain Pan, & Technicoat Evap Coil
Novar ETC-3 Controller, DFS, APS, Double Wall, SS Drain Pan, & Technicoat Evap and Cond Coils
Noval ETC-3 Controller, DFS, APS, Double Wall, SS Drain Pan, Phase Monitor, Coil Guard, & Technicoat Evap and Cond Coils
Technicoat Condenser Coil
Technicoat Condenser Coil & Phase Monitor
Technicoat Condenser Coil & Coil Guard
Technicoat Condenser Coil & Dirty Filter Switch
Technicoat Condenser Coil, Phase Monitor, & Coil Guard
Technicoat Condenser Coil, Phase Monitor, & Dirty Filter Switch
Technicoat Condenser Coil, Coil Guard, & Dirty Filter Switch
Technicoat Condenser Coil, Phase Monitor, Coil Guard, & Dirty Filter Switch
Unitary Products Group
9
127915-YIM-A-0405
Additional Options - Standard Cabinet
TJ
TK
TL
TM
TN
TP
TQ
TR
TS
TT
TU
TV
TW
TX
TY
TZ
T1
T2
T3
T4
T5
T6
T7
T8
T9
LA
LB
LC
LD
LE
LF
LG
LH
LJ
LK
LL
LM
LN
LP
LQ
LR
LS
LT
LU
LV
LW
LX
LY
LZ
L1
L2
L3
L4
L5
L6
10
Technicoat Evaporator Coil
Technicoat Evaporator Coil & Phase Monitor
Technicoat Evaporator Coil & Coil Guard
Technicoat Evaporator Coil & Dirty Filter Switch
Technicoat Evaporator Coil, Phase Monitor, & Coil Guard
Technicoat Evaporator Coil, Phase Monitor, & Dirty Filter Switch
Technicoat Evaporator Coil, Coil Guard, & Dirty Filter Switch
Technicoat Evaporator Coil, Phase Monitor, Coil Guard, & Dirty Filter Switch
Technicoat Evaporator & Condenser Coils
Technicoat Evaporator & Condenser Coils & Phase Monitor
Technicoat Evaporator & Condenser Coils & Coil Guard
Technicoat Evaporator & Condenser Coils & Dirty Filter Switch
Technicoat Evaporator & Condenser Coils, Phase Monitor, & Coil Guard
Technicoat Evaporator & Condenser Coils, Phase Monitor, & Dirty Filter Switch
Technicoat Evaporator & Condenser Coils, Coil Guard, & Dirty Filter Switch
Technicoat Evaporator & Condenser Coils, Phase Monitor, Coil Guard, & Dirty Filter Switch
Technicoat Condenser & SS Drain Pan
Technicoat Condenser & Double Wall
Technicoat Condenser Coil, SS Drain Pan, Double Wall, Phase Monitor, Coil Guard, & Dirty Filter Switch
Technicoat Evaporator & SS Drain Pan
Technicoat Evaporator & Double Wall
Technicoat Evaporator Coil, SS Drain Pan, Double Wall, Phase Monitor, Coil Guard, & Dirty Filter Switch
Technicoat Evaporator & Condenser Coils & SS Drain Pan
Technicoat Evaporator & Condenser Coils & Double Wall
Technicoat Evaporator & Condenser Coils, SS Drain Pan, Double Wall, Phase Monitor, Coil Guard, & Dirty Filter Switch
Simplicity Intelli-Comfort Controller
Simplicity Intelli-Comfort Controller, & Phase Monitor
Simplicity Intelli-Comfort Controller, & Coil Guard
Simplicity Intelli-Comfort Controller, Phase Monitor, & Coil Guard
Simplicity Intelli-Comfort Controller, & Technicoat Cond. Coil
Simplicity Intelli-Comfort Controller, Technicoat Cond. Coil, & Phase Monitor
Simplicity Intelli-Comfort Controller, Technicoat Cond. Coil, & Coil Guard
Simplicity Intelli-Comfort Controller, Technicoat Cond. Coil, Phase Monitor, & Coil Guard
Simplicity Intelli-Comfort Controller, & Technicoat Evap. Coil
Simplicity Intelli-Comfort Controller, Technicoat Evap. Coil, & Phase Monitor
Simplicity Intelli-Comfort Controller, Technicoat Evap. Coil, & Coil Guard
Simplicity Intelli-Comfort Controller, Technicoat Evap. Coil, Phase Monitor, & Coil Guard
Simplicity Intelli-Comfort Controller, & Technicoat Evap. & Cond Coils
Simplicity Intelli-Comfort Controller, Technicoat Evap. & Cond Coils, & Phase Monitor
Simplicity Intelli-Comfort Controller, Technicoat Evap. & Cond Coils, & Coil Guard
Simplicity Intelli-Comfort Controller, Technicoat Evap. & Cond Coils, Phase Monitor, & Coil Guard
Simplicity Intelli-Comfort Controller, SS Drain Pan
Simplicity Intelli-Comfort Controller, SS Drain Pan, Phase Monitor, & Coil Guard
Simplicity Intelli-Comfort Controller, SS Drain Pan, & Technicoat Cond Coils
Simplicity Intelli-Comfort Controller, SS Drain Pan, & Technicoat Evap Coil
Simplicity Intelli-Comfort Controller, SS Drain Pan, & Technicoat Evap and Cond Coils
Simplicity Intelli-Comfort Controller, SS Drain Pan, Phase Monitor, Coil Guard, & Technicoat Evap and Cond Coils
Simplicity Intelli-Comfort Controller, Double Wall
Simplicity Intelli-Comfort Controller, Double Wall, Phase Monitor, & Coil Guard
Simplicity Intelli-Comfort Controller, Double Wall, & Technicoat Cond Coils
Simplicity Intelli-Comfort Controller, Double Wall, & Technicoat Evap Coil
Simplicity Intelli-Comfort Controller, Double Wall, & Technicoat Evap and Cond Coils
Simplicity Intelli-Comfort Controller, Double Wall, Phase Monitor, Coil Guard, & Technicoat Evap and Cond Coils
Simplicity Intelli-Comfort Controller, Double Wall, SS Drain Pan, Phase Monitor, & Coil Guard
Simplicity Intelli-Comfort Controller, Double Wall, SS Drain Pan, & Technicoat Cond Coils
Unitary Products Group
127915-YIM-A-0405
Additional Options - Standard Cabinet
L7
L8
L9
WA
WB
WC
WD
WE
WF
WG
WH
WJ
WK
WL
WM
WN
WP
WQ
WR
WS
WT
WU
WV
WW
WX
WY
WZ
W1
W2
W3
W4
W5
W6
W7
W8
W9
Simplicity Intelli-Comfort Controller, Double Wall, SS Drain Pan, & Technicoat Evap Coil
Simplicity Intelli-Comfort Controller, Double Wall, SS Drain Pan, & Technicoat Evap and Cond Coils
Simplicity Intelli-Comfort Controller, Double Wall, SS Drain Pan, Phase Monitor, Coil Guard, & Technicoat Evap and Cond Coils
Intelli-Comfort w/ModLINC Controller
Intelli-Comfort w/ModLINC Controller, & Phase Monitor
Intelli-Comfort w/ModLINC Controller, & Coil Guard
Intelli-Comfort w/ModLINC Controller, Phase Monitor, & Coil Guard
Intelli-Comfort w/ModLINC Controller, & Technicoat Cond. Coil
Intelli-Comfort w/ModLINC Controller, Technicoat Cond. Coil, & Phase Monitor
Intelli-Comfort w/ModLINC Controller, Technicoat Cond. Coil, & Coil Guard
Intelli-Comfort w/ModLINC Controller, Technicoat Cond. Coil, Phase Monitor, & Coil Guard
Intelli-Comfort w/ModLINC Controller, & Technicoat Evap. Coil
Intelli-Comfort w/ModLINC Controller, Technicoat Evap. Coil, & Phase Monitor
Intelli-Comfort w/ModLINC Controller, Technicoat Evap. Coil, & Coil Guard
Intelli-Comfort w/ModLINC Controller, Technicoat Evap. Coil, Phase Monitor, & Coil Guard
Intelli-Comfort w/ModLINC Controller, & Technicoat Evap. & Cond Coils
Intelli-Comfort w/ModLINC Controller, Technicoat Evap. & Cond Coils, & Phase Monitor
Intelli-Comfort w/ModLINC Controller, Technicoat Evap. & Cond Coils, & Coil Guard
Intelli-Comfort w/ModLINC Controller, Technicoat Evap. & Cond Coils, Phase Monitor, & Coil Guard
Intelli-Comfort w/ModLINC Controller, SS Drain Pan
Intelli-Comfort w/ModLINC Controller, SS Drain Pan, Phase Monitor, & Coil Guard
Intelli-Comfort w/ModLINC Controller, SS Drain Pan, & Technicoat Cond Coils
Intelli-Comfort w/ModLINC Controller, SS Drain Pan, & Technicoat Evap Coil
Intelli-Comfort w/ModLINC Controller, SS Drain Pan, & Technicoat Evap and Cond Coils
Intelli-Comfort w/ModLINC Controller, SS Drain Pan, Phase Monitor, Coil Guard, & Technicoat Evap and Cond Coils
Intelli-Comfort w/ModLINC Controller, Double Wall
Intelli-Comfort w/ModLINC Controller, Double Wall, Phase Monitor, & Coil Guard
Intelli-Comfort w/ModLINC Controller, Double Wall, & Technicoat Cond Coils
Intelli-Comfort w/ModLINC Controller, Double Wall, & Technicoat Evap Coil
Intelli-Comfort w/ModLINC Controller, Double Wall, & Technicoat Evap and Cond Coils
Intelli-Comfort w/ModLINC Controller, Double Wall, Phase Monitor, Coil Guard, & Technicoat Evap and Cond Coils
Intelli-Comfort w/ModLINC Controller, Double Wall, SS Drain Pan, Phase Monitor, & Coil Guard
Intelli-Comfort w/ModLINC Controller, Double Wall, SS Drain Pan, & Technicoat Cond Coils
Intelli-Comfort w/ModLINC Controller, Double Wall, SS Drain Pan, & Technicoat Evap Coil
Intelli-Comfort w/ModLINC Controller, Double Wall, SS Drain Pan, & Technicoat Evap and Cond Coils
Intelli-Comfort w/ModLINC Controller, Double Wall, SS Drain Pan, Phase Monitor, Coil Guard, & Technicoat Evap and Cond Coils
Additional Options - Hinged Filter Door & Toolless Access Cabinet
BA
BB
BC
BD
BE
BF
BG
BH
BJ
BK
BL
BM
BN
BP
BQ
BR
Hinged Filter Door & Toolless Access Panels
Phase Monitor, Hinged Filter Door & Toolless Access Panels
Coil Guard, Hinged Filter Door & Toolless Access Panels
Dirty Filter Switch, Hinged Filter Door & Toolless Access Panels
Phase Monitor & Coil Guard, Hinged Filter Door & Toolless Access Panels
Phase Monitor & Dirty Filter Switch, Hinged Filter Door & Toolless Access Panels
Coil Guard & Dirty Filter Switch, Hinged Filter Door & Toolless Access Panels
Phase Monitor, Coil Guard, & Dirty Filter Switch, Hinged Filter Door & Toolless Access Panels
SS Drain Pan & Hinged Filter Door & Toolless Access Panels
SS Drain Pan & Phase Monitor, Hinged Filter Door & Toolless Access Panels
SS Drain Pan & Coil Guard, Hinged Filter Door & Toolless Access Panels
SS Drain Pan & Dirty Filter Switch, Hinged Filter Door & Toolless Access Panels
SS Drain Pan & Phase Monitor & Coil Guard, Dirty Filter Switch, Hinged Filter Door & Toolless Access Panels
Double Wall
Double Wall & Phase Monitor
Double Wall & Dirty Filter Switch
Unitary Products Group
11
127915-YIM-A-0405
Additional Options - Hinged Filter Door & Toolless Access Cabinet
BT
BU
BV
BW
BX
BY
BZ
DA
DB
DC
DD
DE
DF
DG
DH
DJ
DK
DL
DM
DN
DP
DQ
DR
DS
DT
DU
DV
DW
DX
DY
DZ
D1
D2
D3
D4
D5
D6
D7
D8
D9
EA
EB
EC
ED
EE
EF
EG
EH
EJ
EK
EL
EM
12
Double Wall & Coil Guard
Double Wall & Phase Monitor, Dirty Filter Switch & Coil Guard
Double Wall & SS Drain Pan
Double Wall & SS Drain Pan & Phase Monitor
Double Wall & SS Drain Pan & Coil Guard
Double Wall & SS Drain Pan & Dirty Filter Switch
Double Wall & SS Drain Pan & Phase Monitor, Coil Guard, Dirty Filter Switch
CPC Controller with Dirty Filter Switch & Air Proving Switch, Hinged Filter Door & Toolless Access Panels
CPC Controller, DFS, APS & Phase Monitor, Hinged Filter Door & Toolless Access Panels
CPC Controller, DFS, APS & Coil Guard, Hinged Filter Door & Toolless Access Panels
CPC Controller, DFS, APS, Phase Monitor, & Coil Guard, Hinged Filter Door & Toolless Access Panels
CPC Controller, DFS, APS & Technicoat Cond. Coil, Hinged Filter Door & Toolless Access Panels
CPC Controller, DFS, APS, Technicoat Cond. Coil, & Phase Monitor, Hinged Filter Door & Toolless Access Panels
CPC Controller, DFS, APS, Technicoat Cond. Coil, & Coil Guard, Hinged Filter Door & Toolless Access Panels
CPC Controller, DFS, APS, Technicoat Cond. Coil, Phase Monitor, & Coil Guard, Hinged Filter Door & Toolless Access Panels
CPC Controller, DFS, APS & Technicoat Evap. Coil, Hinged Filter Door & Toolless Access Panels
CPC Controller, DFS, APS, Technicoat Evap. Coil, & Phase Monitor, Hinged Filter Door & Toolless Access Panels
CPC Controller, DFS, APS, Technicoat Evap. Coil, & Coil Guard, Hinged Filter Door & Toolless Access Panels
CPC Controller, DFS, APS, Technicoat Evap. Coil, Phase Monitor, & Coil Guard, Hinged Filter Door & Toolless Access Panels
CPC Controller, DFS, APS & Technicoat Evap. & Cond Coils, Hinged Filter Door & Toolless Access Panels
CPC Controller, DFS, APS, Technicoat Evap. & Cond Coils, & Phase Monitor, Hinged Filter Door & Toolless Access Panels
CPC Controller, DFS, APS, Technicoat Evap. & Cond Coils, & Coil Guard, Hinged Filter Door & Toolless Access Panels
CPC Controller, DFS, APS, Technicoat Evap. & Cond Coils, Phase Monitor, & Coil Guard, Hinged Filter Door & Toolless Access Panels
CPC Controller, DFS, APS, SS Drain Pan Hinged Filter Door & Toolless Access Panels
CPC Controller, DFS, APS, SS Drain Pan, Phase Monitor, & Coil Guard Hinged Filter Door & Toolless Access Panels
CPC Controller, DFS, APS, SS Drain Pan, & Technicoat Cond Coils Hinged Filter Door & Toolless Access Panels
CPC Controller, DFS, APS, SS Drain Pan, & Technicoat Evap Coil Hinged Filter Door & Toolless Access Panels
CPC Controller, DFS, APS, SS Drain Pan, & Technicoat Evap and Cond Coils Hinged Filter Door & Toolless Access Panels
CPC Controller, DFS, APS, SS Drain Pan, Phase Monitor, Coil Guard, & Technicoat Evap and Cond Coils Hinged Filter Door & Toolless
Access Panels
CPC Controller, DFS, APS, Double Wall Hinged Filter Door & Toolless Access Panels
CPC Controller, DFS, APS, Double Wall, Phase Monitor, & Coil Guard Hinged Filter Door & Toolless Access Panels
CPC Controller, DFS, APS, Double Wall, & Technicoat Cond Coils Hinged Filter Door & Toolless Access Panels
CPC Controller, DFS, APS, Double Wall, & Technicoat Evap Coil Hinged Filter Door & Toolless Access Panels
CPC Controller, DFS, APS, Double Wall, & Technicoat Evap and Cond Coils Hinged Filter Door & Toolless Access Panels
CPC Controller, DFS, APS, Double Wall, Phase Monitor, Coil Guard, & Technicoat Evap and Cond Coils Hinged Filter Door & Toolless
Access Panels
CPC Controller, DFS, APS, Double Wall, SS Drain Pan, Phase Monitor, & Coil Guard Hinged Filter Door & Toolless Access Panels
CPC Controller, DFS, APS, Double Wall, SS Drain Pan, & Technicoat Cond Coils Hinged Filter Door & Toolless Access Panels
CPC Controller, DFS, APS, Double Wall, SS Drain Pan, & Technicoat Evap Coil Hinged Filter Door & Toolless Access Panels
CPC Controller, DFS, APS, Double Wall, SS Drain Pan, & Technicoat Evap and Cond Coils Hinged Filter Door & Toolless Access Panels
CPC Controller, DFS, APS, Double Wall, SS Drain Pan, Phase Monitor, Coil Guard, & Technicoat Evap and Cond Coils Hinged Filter
Door & Toolless Access Panels
Johnson UNT Controller with Dirty Filter Switch & Air Proving Switch, Hinged Filter Door & Toolless Access Panels
Johnson UNT Controller, DFS, APS & Phase Monitor, Hinged Filter Door & Toolless Access Panels
Johnson UNT Controller, DFS, APS & Coil Guard, Hinged Filter Door & Toolless Access Panels
Johnson UNT Controller, DFS, APS, Phase Monitor, & Coil Guard, Hinged Filter Door & Toolless Access Panels
Johnson UNT Controller, DFS, APS & Technicoat Cond. Coil, Hinged Filter Door & Toolless Access Panels
Johnson UNT Controller, DFS, APS, Technicoat Cond. Coil, & Phase Monitor, Hinged Filter Door & Toolless Access Panels
Johnson UNT Controller, DFS, APS, Technicoat Cond. Coil, & Coil Guard, Hinged Filter Door & Toolless Access Panels
Johnson UNT Controller, DFS, APS, Technicoat Cond. Coil, Phase Monitor, & Coil Guard, Hinged Filter Door & Toolless Access Panels
Johnson UNT Controller, DFS, APS & Technicoat Evap. Coil, Hinged Filter Door & Toolless Access Panels
Johnson UNT Controller, DFS, APS, Technicoat Evap. Coil, & Phase Monitor, Hinged Filter Door & Toolless Access Panels
Johnson UNT Controller, DFS, APS, Technicoat Evap. Coil, & Coil Guard, Hinged Filter Door & Toolless Access Panels
Johnson UNT Controller, DFS, APS, Technicoat Evap. Coil, Phase Monitor, & Coil Guard, Hinged Filter Door & Toolless Access Panels
Unitary Products Group
127915-YIM-A-0405
Additional Options - Hinged Filter Door & Toolless Access Cabinet
EN
EP
EQ
ER
ES
ET
EU
EV
EW
EX
EY
EZ
E1
E2
E3
E4
E5
E6
E7
E8
E9
GA
GB
GC
GD
GE
GF
GG
GH
GJ
GK
GL
GM
GN
GP
GQ
GR
GS
GT
GU
GV
GW
GX
GY
GZ
G1
G2
G3
G4
G5
Johnson UNT Controller, DFS, APS & Technicoat Evap. & Cond Coils, Hinged Filter Door & Toolless Access Panels
Johnson UNT Controller, DFS, APS, Technicoat Evap. & Cond Coils, & Phase Monitor, Hinged Filter Door & Toolless Access Panels
Johnson UNT Controller, DFS, APS, Technicoat Evap. & Cond Coils, & Coil Guard, Hinged Filter Door & Toolless Access Panels
Johnson UNT Controller, DFS, APS, Technicoat Evap. & Cond Coils, Phase Monitor, & Coil Guard, Hinged Filter Door & Toolless Access
Panels
Johnson UNT Controller, DFS, APS, SS Drain Pan Hinged Filter Door & Toolless Access Panels
Johnson UNT Controller, DFS, APS, SS Drain Pan, Phase Monitor, & Coil Guard Hinged Filter Door & Toolless Access Panels
Johnson UNT Controller, DFS, APS, SS Drain Pan, & Technicoat Cond Coils Hinged Filter Door & Toolless Access Panels
Johnson UNT Controller, DFS, APS, SS Drain Pan, & Technicoat Evap Coil Hinged Filter Door & Toolless Access Panels
Johnson UNT Controller, DFS, APS, SS Drain Pan, & Technicoat Evap and Cond Coils Hinged Filter Door & Toolless Access Panels
Johnson UNT Controller, DFS, APS, SS Drain Pan, Phase Monitor, Coil Guard, & Technicoat Evap and Cond Coils Hinged Filter Door &
Toolless Access Panels
Johnson UNT Controller, DFS, APS, Double Wall Hinged Filter Door & Toolless Access Panels
Johnson UNT Controller, DFS, APS, Double Wall, Phase Monitor, & Coil Guard Hinged Filter Door & Toolless Access Panels
Johnson UNT Controller, DFS, APS, Double Wall, & Technicoat Cond Coils Hinged Filter Door & Toolless Access Panels
Johnson UNT Controller, DFS, APS, Double Wall, & Technicoat Evap Coil Hinged Filter Door & Toolless Access Panels
Johnson UNT Controller, DFS, APS, Double Wall, & Technicoat Evap and Cond Coils Hinged Filter Door & Toolless Access Panels
Johnson UNT Controller, DFS, APS, Double Wall, Phase Monitor, Coil Guard, & Technicoat Evap and Cond Coils Hinged Filter Door &
Toolless Access Panels
Johnson UNT Controller, DFS, APS, Double Wall, SS Drain Pan, Phase Monitor, & Coil Guard Hinged Filter Door & Toolless Access Panels
Johnson UNT Controller, DFS, APS, Double Wall, SS Drain Pan, & Technicoat Cond Coils Hinged Filter Door & Toolless Access Panels
Johnson UNT Controller, DFS, APS, Double Wall, SS Drain Pan, & Technicoat Evap Coil Hinged Filter Door & Toolless Access Panels
Johnson UNT Controller, DFS, APS, Double Wall, SS Drain Pan, & Technicoat Evap and Cond Coils Hinged Filter Door & Toolless
Access Panels
Johnson UNT Controller, DFS, APS, Double Wall, SS Drain Pan, Phase Monitor, Coil Guard, & Technicoat Evap and Cond Coils Hinged
Filter Door & Toolless Access Panels
Honeywell Excel 10 Controller with Dirty Filter Switch & Air Proving Switch, Hinged Filter Door & Toolless Access Panels
Honeywell Excel 10 Controller, DFS, APS & Phase Monitor, Hinged Filter Door & Toolless Access Panels
Honeywell Excel 10 Controller, DFS, APS & Coil Guard, Hinged Filter Door & Toolless Access Panels
Honeywell Excel 10 Controller, DFS, APS, Phase Monitor, & Coil Guard, Hinged Filter Door & Toolless Access Panels
Honeywell Excel 10 Controller, DFS, APS & Technicoat Cond. Coil, Hinged Filter Door & Toolless Access Panels
Honeywell Excel 10 Controller, DFS, APS, Technicoat Cond. Coil, & Phase Monitor, Hinged Filter Door & Toolless Access Panels
Honeywell Excel 10 Controller, DFS, APS, Technicoat Cond. Coil, & Coil Guard, Hinged Filter Door & Toolless Access Panels
Honeywell Excel 10 Controller, DFS, APS, Technicoat Cond. Coil, Phase Monitor, & Coil Guard, Hinged Filter Door & Toolless Access
Panels
Honeywell Excel 10 Controller, DFS, APS & Technicoat Evap. Coil, Hinged Filter Door & Toolless Access Panels
Honeywell Excel 10 Controller, DFS, APS, Technicoat Evap. Coil, & Phase Monitor, Hinged Filter Door & Toolless Access Panels
Honeywell Excel 10 Controller, DFS, APS, Technicoat Evap. Coil, & Coil Guard, Hinged Filter Door & Toolless Access Panels
Honeywell Excel 10 Controller, DFS, APS, Technicoat Evap. Coil, Phase Monitor, & Coil Guard, Hinged Filter Door & Toolless Access
Panels
Honeywell Excel 10 Controller, DFS, APS & Technicoat Evap. & Cond Coils, Hinged Filter Door & Toolless Access Panels
Honeywell Excel 10 Controller, DFS, APS, Technicoat Evap. & Cond Coils, & Phase Monitor, Hinged Filter Door & Toolless Access Panels
Honeywell Excel 10 Controller, DFS, APS, Technicoat Evap. & Cond Coils, & Coil Guard, Hinged Filter Door & Toolless Access Panels
Honeywell Excel 10 Controller, DFS, APS, Technicoat Evap. & Cond Coils, Phase Monitor, & Coil Guard, Hinged Filter Door & Toolless
Access Panels
Honeywell Excel 10 Controller, DFS, APS, SS Drain Pan
Honeywell Excel 10 Controller, DFS, APS, SS Drain Pan, Phase Monitor, & Coil Guard
Honeywell Excel 10 Controller, DFS, APS, SS Drain Pan, & Technicoat Cond Coils
Honeywell Excel 10 Controller, DFS, APS, SS Drain Pan, & Technicoat Evap Coil
Honeywell Excel 10 Controller, DFS, APS, SS Drain Pan, & Technicoat Evap and Cond Coils
Honeywell Excel 10 Controller, DFS, APS, SS Drain Pan, Phase Monitor, Coil Guard, & Technicoat Evap and Cond Coils
Honeywell Excel 10 Controller, DFS, APS, Double Wall
Honeywell Excel 10 Controller, DFS, APS, Double Wall, Phase Monitor, & Coil Guard
Honeywell Excel 10 Controller, DFS, APS, Double Wall, & Technicoat Cond Coils
Honeywell Excel 10 Controller, DFS, APS, Double Wall, & Technicoat Evap Coil
Honeywell Excel 10 Controller, DFS, APS, Double Wall, & Technicoat Evap and Cond Coils
Honeywell Excel 10 Controller, DFS, APS, Double Wall, Phase Monitor, Coil Guard, & Technicoat Evap and Cond Coils
Honeywell Excel 10 Controller, DFS, APS, Double Wall, SS Drain Pan, Phase Monitor, & Coil Guard
Unitary Products Group
13
127915-YIM-A-0405
Additional Options - Hinged Filter Door & Toolless Access Cabinet
G6
G7
G8
G9
PA
PB
PC
PD
PE
PF
PG
PH
PJ
PK
PL
PM
PN
PP
PQ
PR
Honeywell Excel 10 Controller, DFS, APS, Double Wall, SS Drain Pan, & Technicoat Cond Coils
Honeywell Excel 10 Controller, DFS, APS, Double Wall, SS Drain Pan, & Technicoat Evap Coil
Honeywell Excel 10 Controller, DFS, APS, Double Wall, SS Drain Pan, & Technicoat Evap and Cond Coils
Honeywell Excel 10 Controller, DFS, APS, Double Wall, SS Drain Pan, Phase Monitor, Coil Guard, & Technicoat Evap and Cond Coils
Novar ETC-3 Controller with Dirty Filter Switch & Air Proving Switch, Hinged Filter Door & Toolless Access Panels
Novar ETC-3 Controller, DFS, APS & Phase Monitor, Hinged Filter Door & Toolless Access Panels
Novar ETC-3 Controller, DFS, APS & Coil Guard, Hinged Filter Door & Toolless Access Panels
Novar ETC-3 Controller, DFS, APS, Phase Monitor, & Coil Guard, Hinged Filter Door & Toolless Access Panels
Novar ETC-3 Controller, DFS, APS & Technicoat Cond. Coil, Hinged Filter Door & Toolless Access Panels
Novar ETC-3 Controller, DFS, APS, Technicoat Cond. Coil, & Phase Monitor, Hinged Filter Door & Toolless Access Panels
Novar ETC-3 Controller, DFS, APS, Technicoat Cond. Coil, & Coil Guard, Hinged Filter Door & Toolless Access Panels
Novar ETC-3 Controller, DFS, APS, Technicoat Cond. Coil, Phase Monitor, & Coil Guard, Hinged Filter Door & Toolless Access Panels
Novar ETC-3 Controller, DFS, APS & Technicoat Evap. Coil, Hinged Filter Door & Toolless Access Panels
Novar ETC-3 Controller, DFS, APS, Technicoat Evap. Coil, & Phase Monitor, Hinged Filter Door & Toolless Access Panels
Novar ETC-3 Controller, DFS, APS, Technicoat Evap. Coil, & Coil Guard, Hinged Filter Door & Toolless Access Panels
Novar ETC-3 Controller, DFS, APS, Technicoat Evap. Coil, Phase Monitor, & Coil Guard, Hinged Filter Door & Toolless Access Panels
Novar ETC-3 Controller, DFS, APS & Technicoat Evap. & Cond Coils, Hinged Filter Door & Toolless Access Panels
Novar ETC-3 Controller, DFS, APS, Technicoat Evap. & Cond Coils, & Phase Monitor, Hinged Filter Door & Toolless Access Panels
Novar ETC-3 Controller, DFS, APS, Technicoat Evap. & Cond Coils, & Coil Guard, Hinged Filter Door & Toolless Access Panels
Novar ETC-3 Controller, DFS, APS, Technicoat Evap. & Cond Coils, Phase Monitor, & Coil Guard, Hinged Filter Door & Toolless Access
Panels
PS Novar ETC-3 Controller, DFS, APS, SS Drain Pan
PT Novar ETC-3 Controller, DFS, APS, SS Drain Pan, Phase Monitor, & Coil Guard
PU Novar ETC-3 Controller, DFS, APS, SS Drain Pan, & Technicoat Cond Coils
PV Novar ETC-3 Controller, DFS, APS, SS Drain Pan, & Technicoat Evap Coil
PW Novar ETC-3, DFS, APS, SS Drain Pan, & Technicoat Evap and Cond Coils
PX Novar ETC-3 Controller, DFS, APS, SS Drain Pan, Phase Monitor, Coil Guard, & Technicoat Evap and Cond Coils
PY Novar ETC-3 Controller, DFS, APS, Double Wall
PZ Novar ETC-3 Controller, DFS, APS, Double Wall, Phase Monitor, & Coil Guard
P1 Novar ETC-3 Controller, DFS, APS, Double Wall, & Technicoat Cond Coils
P2 Novar ETC-3 Controller, DFS, APS, Double Wall, & Technicoat Evap Coil
P3 Novar ETC-3 Controller, DFS, APS, Double Wall, & Technicoat Evap and Cond Coils
P4 Novar ETC-3 Controller, DFS, APS, Double Wall, Phase Monitor, Coil Guard, & Technicoat Evap and Cond Coils
P5 Novar ETC-3 Controller, DFS, APS, Double Wall, SS Drain Pan, Phase Monitor, & Coil Guard
P6 Novar ETC-3 Controller, DFS, APS, Double Wall, SS Drain Pan, & Technicoat Cond Coils
P7 Novar ETC-3 Controller, DFS, APS, Double Wall, SS Drain Pan, & Technicoat Evap Coil
P8 Novar ETC-3 Controller, DFS, APS, Double Wall, SS Drain Pan, & Technicoat Evap and Cond Coils
P9 Novar ETC-3 Controller, DFS, APS, Double Wall, SS Drain Pan, Phase Monitor, Coil Guard, & Technicoat Evap and Cond Coils
UA Technicoat Condenser Coil, Hinged Filter Door & Toolless Access Panels
UB Technicoat Condenser Coil & Phase Monitor, Hinged Filter Door & Toolless Access Panels
UC Technicoat Condenser Coil & Coil Guard, Hinged Filter Door & Toolless Access Panels
UD Technicoat Condenser Coil & Dirty Filter Switch, Hinged Filter Door & Toolless Access Panels
UE Technicoat Condenser Coil, Phase Monitor, & Coil Guard, Hinged Filter Door & Toolless Access Panels
UF Technicoat Condenser Coil, Phase Monitor, & Dirty Filter Switch, Hinged Filter Door & Toolless Access Panels
UG Technicoat Condenser Coil, Coil Guard, & Dirty Filter Switch, Hinged Filter Door & Toolless Access Panels
UH Technicoat Condenser Coil, Phase Monitor, Coil Guard, & Dirty Filter Switch, Hinged Filter Door & Toolless Access Panels
UJ Technicoat Evaporator Coil, Hinged Filter Door & Toolless Access Panels
UK Technicoat Evaporator Coil & Phase Monitor, Hinged Filter Door & Toolless Access Panels
UL Technicoat Evaporator Coil & Coil Guard, Hinged Filter Door & Toolless Access Panels
UM Technicoat Evaporator Coil & Dirty Filter Switch, Hinged Filter Door & Toolless Access Panels
UN Technicoat Evaporator Coil, Phase Monitor, & Coil Guard, Hinged Filter Door & Toolless Access Panels
UP Technicoat Evaporator Coil, Phase Monitor, & Dirty Filter Switch, Hinged Filter Door & Toolless Access Panels
UQ Technicoat Evaporator Coil, Coil Guard, & Dirty Filter Switch, Hinged Filter Door & Toolless Access Panels
UR Technicoat Evaporator Coil, Phase Monitor, Coil Guard, & Dirty Filter Switch, Hinged Filter Door & Toolless Access Panels
US Technicoat Evaporator & Condenser Coils, Hinged Filter Door & Toolless Access Panels
14
Unitary Products Group
127915-YIM-A-0405
Additional Options - Hinged Filter Door & Toolless Access Cabinet
UT
UU
UV
UW
UX
UY
UZ
U1
U2
U3
U4
U5
U6
U7
U8
U9
QA
QB
QC
QD
QE
QF
QG
QH
QJ
QK
QL
QM
QN
QP
QQ
QR
QS
QT
QU
QV
QW
QX
QY
QZ
Q1
Q2
Q3
Q4
Q5
Q6
Q7
Q8
Q9
Technicoat Evaporator & Condenser Coils & Phase Monitor, Hinged Filter Door & Toolless Access Panels
Technicoat Evaporator & Condenser Coils & Coil Guard, Hinged Filter Door & Toolless Access Panels
Technicoat Evaporator & Condenser Coils & Dirty Filter Switch, Hinged Filter Door & Toolless Access Panels
Technicoat Evaporator & Condenser Coils, Phase Monitor, & Coil Guard, Hinged Filter Door & Toolless Access Panels
Technicoat Evaporator & Condenser Coils, Phase Monitor, & Dirty Filter Switch, Hinged Filter Door & Toolless Access Panels
Technicoat Evaporator & Condenser Coils, Coil Guard, & Dirty Filter Switch, Hinged Filter Door & Toolless Access Panels
Technicoat Evaporator & Condenser Coils, Phase Monitor, Coil Guard, & Dirty Filter Switch, Hinged Filter Door & Toolless Access Panels
Technicoat Condenser & SS Drain Pan, Hinged Filter Door & Toolless Access Panels
Technicoat Condenser & Double Wall, Hinged Filter Door & Toolless Access Panels
Technicoat Condenser Coil, SS Drain Pan, Double Wall, Phase Monitor, Coil Guard, & Dirty Filter Switch, Hinged Filter Door & Toolless
Access Panels
Technicoat Evaporator & SS Drain Pan, Hinged Filter Door & Toolless Access Panels
Technicoat Evaporator & Double Wall, Hinged Filter Door & Toolless Access Panels
Technicoat Evaporator Coil, SS Drain Pan, Double Wall, Phase Monitor, Coil Guard, & Dirty Filter Switch, Hinged Filter Door & Toolless
Access Panels
Technicoat Evaporator & Condenser Coils & SS Drain Pan, Hinged Filter Door & Toolless Access Panels
Technicoat Evaporator & Condenser Coils & Double Wall, Hinged Filter Door & Toolless Access Panels
Technicoat Evaporator & Condenser Coils, SS Drain Pan, Double Wall, Phase Monitor, Coil Guard, & Dirty Filter Switch, Hinged Filter
Door & Toolless Access Panels
Simplicity Intelli-Comfort Controller with Hinged Filter Door & Toolless Access Panels
Simplicity Intelli-Comfort Controller, & Phase Monitor, Hinged Filter Door & Toolless Access Panels
Simplicity Intelli-Comfort Controller, & Coil Guard, Hinged Filter Door & Toolless Access Panels
Simplicity Intelli-Comfort Controller, Phase Monitor, & Coil Guard, Hinged Filter Door & Toolless Access Panels
Simplicity Intelli-Comfort Controller, & Technicoat Cond. Coil, Hinged Filter Door & Toolless Access Panels
Simplicity Intelli-Comfort Controller, Technicoat Cond. Coil, & Phase Monitor, Hinged Filter Door & Toolless Access Panels
Simplicity Intelli-Comfort Controller, Technicoat Cond. Coil, & Coil Guard, Hinged Filter Door & Toolless Access Panels
Simplicity Intelli-Comfort Controller, Technicoat Cond. Coil, Phase Monitor, & Coil Guard, Hinged Filter Door & Toolless Access
Simplicity Intelli-Comfort Controller, & Technicoat Evap. Coil, Hinged Filter Door & Toolless Access Panels
Simplicity Intelli-Comfort Controller, Technicoat Evap. Coil, & Phase Monitor, Hinged Filter Door & Toolless Access Panels
Simplicity Intelli-Comfort Controller, Technicoat Evap. Coil, & Coil Guard, Hinged Filter Door & Toolless Access Panels
Simplicity Intelli-Comfort Controller, Technicoat Evap. Coil, Phase Monitor, & Coil Guard, Hinged Filter Door & Toolless Access
Simplicity Intelli-Comfort Controller, & Technicoat Evap. & Cond Coils, Hinged Filter Door & Toolless Access Panels
Simplicity Intelli-Comfort Controller, Technicoat Evap. & Cond Coils, & Phase Monitor, Hinged Filter Door & Toolless Access Pan
Simplicity Intelli-Comfort Controller, Technicoat Evap. & Cond Coils, & Coil Guard, Hinged Filter Door & Toolless Access Panels
Simplicity Intelli-Comfort Controller, Technicoat Evap. & Cond Coils, Phase Monitor, & Coil Guard, Hinged Filter Door & Toolless
Simplicity Intelli-Comfort Controller, SS Drain Pan Hinged Filter Door & Toolless Access Panels
Simplicity Intelli-Comfort Controller, SS Drain Pan, Phase Monitor, & Coil Guard Hinged Filter Door & Toolless Access Panels
Simplicity Intelli-Comfort Controller, SS Drain Pan, & Technicoat Cond Coils Hinged Filter Door & Toolless Access Panels
Simplicity Intelli-Comfort Controller, SS Drain Pan, & Technicoat Evap Coil Hinged Filter Door & Toolless Access Panels
Simplicity Intelli-Comfort Controller, SS Drain Pan, & Technicoat Evap and Cond Coils Hinged Filter Door & Toolless Access Panels
Simplicity Intelli-Comfort Controller, SS Drain Pan, Phase Monitor, Coil Guard, & Technicoat Evap and Cond Coils Hinged Filter Door &
Toolless Access Panels
Simplicity Intelli-Comfort Controller, Double Wall Hinged Filter Door & Toolless Access Panels
Simplicity Intelli-Comfort Controller, Double Wall, Phase Monitor, & Coil Guard Hinged Filter Door & Toolless Access Panels
Simplicity Intelli-Comfort Controller, Double Wall, & Technicoat Cond Coils Hinged Filter Door & Toolless Access Panels
Simplicity Intelli-Comfort Controller, Double Wall, & Technicoat Evap Coil Hinged Filter Door & Toolless Access Panels
Simplicity Intelli-Comfort Controller, Double Wall, & Technicoat Evap and Cond Coils Hinged Filter Door & Toolless Access Panels
Simplicity Intelli-Comfort Controller, Double Wall, Phase Monitor, Coil Guard, & Technicoat Evap and Cond Coils Hinged Filter Door &
Toolless Access Panels
Simplicity Intelli-Comfort Controller, Double Wall, SS Drain Pan, Phase Monitor, & Coil Guard Hinged Filter Door & Toolless Access Panels
Simplicity Intelli-Comfort Controller, Double Wall, SS Drain Pan, & Technicoat Cond Coils Hinged Filter Door & Toolless Access Panels
Simplicity Intelli-Comfort Controller, Double Wall, SS Drain Pan, & Technicoat Evap Coil Hinged Filter Door & Toolless Access Panels
Simplicity Intelli-Comfort Controller, Double Wall, SS Drain Pan, & Technicoat Evap and Cond Coils Hinged Filter Door & Toolless Access
Panels
Simplicity Intelli-Comfort Controller, Double Wall, SS Drain Pan, Phase Monitor, Coil Guard, & Technicoat Evap and Cond Coils Hinged
Filter Door & Toolless Access Panels
Unitary Products Group
15
127915-YIM-A-0405
Additional Options - Hinged Filter Door & Toolless Access Cabinet
XA
XB
XC
XD
XE
XF
XG
XH
XJ
XK
XL
XM
XN
XP
XQ
XR
XS
XT
XU
XV
XW
XX
XY
XZ
X1
X2
X3
X4
X5
X6
X7
X8
X9
16
Intelli-Comfort w/ModLINC Controller, Hinged Filter Door & Toolless Access Panels
Intelli-Comfort w/ModLINC Controller, & Phase Monitor, Hinged Filter Door & Toolless Access Panels
Intelli-Comfort w/ModLINC Controller, & Coil Guard, Hinged Filter Door & Toolless Access Panels
Intelli-Comfort w/ModLINC Controller, Phase Monitor, & Coil Guard, Hinged Filter Door & Toolless Access Panels
Intelli-Comfort w/ModLINC Controller, & Technicoat Cond. Coil, Hinged Filter Door & Toolless Access Panels
Intelli-Comfort w/ModLINC Controller, Technicoat Cond. Coil, & Phase Monitor, Hinged Filter Door & Toolless Access Panels
Intelli-Comfort w/ModLINC Controller, Technicoat Cond. Coil, & Coil Guard, Hinged Filter Door & Toolless Access Panels
Intelli-Comfort w/ModLINC Controller, Technicoat Cond. Coil, Phase Monitor, & Coil Guard, Hinged Filter Door & Toolless Access
Intelli-Comfort w/ModLINC Controller, & Technicoat Evap. Coil, Hinged Filter Door & Toolless Access Panels
Intelli-Comfort w/ModLINC Controller, Technicoat Evap. Coil, & Phase Monitor, Hinged Filter Door & Toolless Access Panels
Intelli-Comfort w/ModLINC Controller, Technicoat Evap. Coil, & Coil Guard, Hinged Filter Door & Toolless Access Panels
Intelli-Comfort w/ModLINC Controller, Technicoat Evap. Coil, Phase Monitor, & Coil Guard, Hinged Filter Door & Toolless Access
Intelli-Comfort w/ModLINC Controller, & Technicoat Evap. & Cond Coils, Hinged Filter Door & Toolless Access Panels
Intelli-Comfort w/ModLINC Controller, Technicoat Evap. & Cond Coils, & Phase Monitor, Hinged Filter Door & Toolless Access Pan
Intelli-Comfort w/ModLINC Controller, Technicoat Evap. & Cond Coils, & Coil Guard, Hinged Filter Door & Toolless Access Panels
Intelli-Comfort w/ModLINC Controller, Technicoat Evap. & Cond Coils, Phase Monitor, & Coil Guard, Hinged Filter Door & Toolless
Intelli-Comfort w/ModLINC Controller, SS Drain Pan Hinged Filter Door & Toolless Access Panels
Intelli-Comfort w/ModLINC Controller, SS Drain Pan, Phase Monitor, & Coil Guard Hinged Filter Door & Toolless Access Panels
Intelli-Comfort w/ModLINC Controller, SS Drain Pan, & Technicoat Cond Coils Hinged Filter Door & Toolless Access Panels
Intelli-Comfort w/ModLINC Controller, SS Drain Pan, & Technicoat Evap Coil Hinged Filter Door & Toolless Access Panels
Intelli-Comfort w/ModLINC Controller, SS Drain Pan, & Technicoat Evap and Cond Coils Hinged Filter Door & Toolless Access Panels
Intelli-Comfort w/ModLINC Controller, SS Drain Pan, Phase Monitor, Coil Guard, & Technicoat Evap and Cond Coils Hinged Filter Door &
Toolless Access Panels
Intelli-Comfort w/ModLINC Controller, Double Wall Hinged Filter Door & Toolless Access Panels
Intelli-Comfort w/ModLINC Controller, Double Wall, Phase Monitor, & Coil Guard Hinged Filter Door & Toolless Access Panels
Intelli-Comfort w/ModLINC Controller, Double Wall, & Technicoat Cond Coils Hinged Filter Door & Toolless Access Panels
Intelli-Comfort w/ModLINC Controller, Double Wall, & Technicoat Evap Coil Hinged Filter Door & Toolless Access Panels
Intelli-Comfort w/ModLINC Controller, Double Wall, & Technicoat Evap and Cond Coils Hinged Filter Door & Toolless Access Panels
Intelli-Comfort w/ModLINC Controller, Double Wall, Phase Monitor, Coil Guard, & Technicoat Evap and Cond Coils Hinged Filter Door &
Toolless Access Panels
Intelli-Comfort w/ModLINC Controller, Double Wall, SS Drain Pan, Phase Monitor, & Coil Guard Hinged Filter Door & Toolless Access
Panels
Intelli-Comfort w/ModLINC Controller, Double Wall, SS Drain Pan, & Technicoat Cond Coils Hinged Filter Door & Toolless Access Panels
Intelli-Comfort w/ModLINC Controller, Double Wall, SS Drain Pan, & Technicoat Evap Coil Hinged Filter Door & Toolless Access Panels
Intelli-Comfort w/ModLINC Controller, Double Wall, SS Drain Pan, & Technicoat Evap and Cond Coils Hinged Filter Door & Toolless
Access Panels
Intelli-Comfort w/ModLINC Controller, Double Wall, SS Drain Pan, Phase Monitor, Coil Guard, & Technicoat Evap and Cond Coils Hinged
Filter Door & Toolless Access Panels
Unitary Products Group
127915-YIM-A-0405
INSTALLATION
INSTALLATION SAFETY INFORMATION:
Read these instructions before continuing this appliance installation. This is an outdoor combination heating and cooling unit. The installer must assure that
these instructions are made available to the consumer
and with instructions to retain them for future reference.
1. Refer to the furnace rating plate for the approved
type of gas for this furnace.
•
Local gas utility requirements.
In Canada:
•
Current Canadian Electrical Code C22.1.
•
Current Gas Installation Codes CSA-B149.1.
•
Local plumbing and waste water codes.
•
Other applicable local codes.
Refer to the Unit Application Data Table 1 and to the
Gas Heat Application Data Table 4.
2. Install this furnace only in a location and position
as specified on Page 17 of these instructions.
If components are to be added to a unit to meet local
codes, they are to be installed at the dealer's and/or
the customer's expense.
3. Never test for gas leaks with an open flame. Use
commercially available soap solution made specifically for the detection of leaks when checking all
connections.
Size of unit for proposed installation should be based
on heat loss/heat gain calculation made according to
the methods of the Air Conditioning Contractors of
America (ACCA).
4. Always install furnace to operate within the furnace's intended temperature-rise range with the
duct system and within the allowable external static
pressure range, as specified on the unit name/rating plate.
TABLE 1: UNIT APPLICATION DATA
5. This equipment is not to be used for temporary
heating or cooling of buildings or structures under
construction.
FIRE OR EXPLOSION HAZARD
Failure to follow the safety warning exactly
could result in serious injury, death or property
damage.
Never test for gas leaks with an open flame.
Use a commercially available soap solution
made specifically for the detection of leaks to
check all connections. A fire or explosion may
result causing property damage, personal
injury or loss of life.
LIMITATIONS
These units must be installed in accordance with the
following national and local safety codes:
In U.S.A.:
•
National Electrical Code ANSI/NFPA No. 70.
•
National Fuel Gas Code Z223.1.
•
Gas-Fired Central Furnace Standard ANSI
Z21.47a.
Unitary Products Group
UNIT MODEL NUMBER
Voltage Variation,
Min. / Max.1
DR180
DR240
208/230-3-60
187/253
460-3-60
414/506
575-3-60
518/630
Supply Air CFM, Min. / Max.
4,500/
7,500
6,000/
9,400
Wet Bulb Temperature (ºF) of Air on
Evaporator Coil, Min. / Max.
57/72
Dry Bulb Temperature (ºF) of Air on
Condenser Coil, Min. / Max.
0/125
1.
DR300
7,500/
11,500
Utilization range “A” in accordance with ARI Standard
110.
LOCATION
Use the following guidelines to select a suitable location for these units.
1. Unit is designed for outdoor installation only.
2. Condenser coils must have an unlimited supply of
air.
3. Where a choice of location is possible, position the
unit on either north or east side of building.
4. For ground level installation, use a level concrete
slab with a minimum thickness of 4 inches. The
length and width should be at least 6 inches
greater than the unit base rails. Do not tie slab to
the building foundation.
5. Roof structures must be able to support the weight
of the unit and its options and/or accessories. Unit
must be installed on a solid level roof curb or
appropriate angle iron frame.
17
127915-YIM-A-0405
6. Maintain level tolerance to 1/2 inch maximum
across the entire length or width of the unit.
Excessive exposure of this furnace to contaminated combustion air may result in equipment
damage or personal injury. Typical contaminates include: permanent wave solutions, chlorinated waxes and cleaners, chlorine based
swimming pool chemicals, water softening
chemicals, carbon tetrachloride, Halogen type
refrigerants, cleaning solvents (e.g. perchloroethylene), printing inks, paint removers, varnishes, hydrochloric acid, cements and glues,
antistatic fabric softeners for clothes dryers,
masonry acid washing materials.
FIGURE 1 - TYPICAL RIGGING
If a unit is to be installed on a roof curb or special frame
other than a YORK roof curb, gasketing must be
applied to all surfaces that come in contact with the unit
underside.
RIGGING AND HANDLING
Exercise care when moving the unit. Do not remove
any packaging until the unit is near the place of installation. Rig the unit by attaching chain or cable slings to
the round lifting holes provided in the base rails.
Spreaders, whose length exceeds the largest dimension across the unit, MUST BE USED. Refer to
Figure 1.
Units may also be moved or lifted with a forklift, from
the side only, providing that an accessory skid is used.
LENGTH OF FORKS MUST BE A MINIMUM OF 90".
Refer to the Physical Data Table 7 for unit weights and
to the Figures 2 or 12 for approximate center of gravity.
Before lifting a unit, make sure that all panels
are in place and that its weight is distributed
equally on all cables so it will lift evenly.
18
47.5" (15, 20, 25 TON)
FIGURE 2 - CENTER OF GRAVITY
CLEARANCES
All units require certain clearances for proper operation
and service. Installer must make provisions for adequate combustion and ventilation air in accordance
with Section 5.3, Air for Combustion and Ventilation of
the National Fuel Gas Code, ANSI Z223.1 (in U.S.A.)
or Sections 7.2, 7.3 or 7.4 of Gas Installation Codes
CSA-B149.1 (in Canada) and/or applicable provisions
of the local building codes. Refer to Dimensions and
Clearances Figure 12 for the clearances required for
combustible construction, servicing, and proper unit
operation.
Do not permit overhanging structures or shrubs
to obstruct outdoor air discharge outlet, combustion air inlet or vent outlets.
Unitary Products Group
127915-YIM-A-0405
DUCTWORK
Ductwork should be designed and sized according to
the methods in Manual Q of the Air Conditioning Contractors of America (ACCA).
A closed return duct system shall be used. This shall
not preclude use of economizers or outdoor fresh air
intake. The supply and return air duct connections at
the unit should be made with flexible joints to minimize
noise.
The supply and return air duct systems should be
designed for the CFM and static requirements of the
job. They should NOT be sized to match the dimensions of the duct connections on the unit.
When fastening ductwork to side duct flanges
on unit, insert screws through duct flanges
only. DO NOT insert screws through casing.
Outdoor ductwork must be insulated and
waterproofed.
Refer to Dimensions and Clearances Figure 12 for
information concerning side and bottom supply and
return air duct openings.
NOTE: It is recommended that, in Canada, the outlet
duct be provided with a removable access
panel. It is recommended that this opening be
accessible when the unit is installed in service,
and of a size such that smoke or reflected light
may be observed inside the casing to indicate
the presence of leaks in the heat exchanger.
The cover should be attached in a manner
adequate to prevent leakage.
FIXED OUTDOOR AIR INTAKE DAMPER
This damper is shipped inside the return air compartment. It is completely assembled and ready for installation. A damper baffle inside of the hood is adjustable to
Unitary Products Group
provide variable amounts of outdoor air intake on units
that are not provided with an economizer or a motorized damper option. Refer to the Fixed Outdoor
Damper Figure 3.
Gasketing and mounting screws are provided in a parts
bag attached to the hood assembly. Apply gasketing to
the three flange surfaces on the hood prior to installing
the hood. Extend gasketing 1/4 inch beyond the top
and bottom of the two side flanges to insure adequate
sealing.
Adjusting the damper to the desired air flow may be
done before mounting the hood into position or after
installation by removing the front hood panel or the
screen on the bottom of the hood. Damper baffle in
position 1 will allow approximately 10% outdoor air
flow, position 2 approximately 15% and, to allow
approximately 25%, remove the damper baffle.
On units with bottom return air application install the
damper assembly over the opening in the side return
air access panel. Remove and discard the opening
cover and the covering over the hood mounting holes
(used for shipping) before installing. Secure with the
screws provided.
On units with side return air applications, install the
damper assembly on the return air ductwork as close
to the unit as possible. Cut an opening 16 inches high
by 18 inches wide in the ductwork to accommodate the
damper. Using the holes in the hood flanges as a template, drill 9/64 inch dia. (#26 drill) holes into the ductwork and secure with the screws provided.
If outdoor air intake will not be required on
units with bottom return air applications, the
damper assembly should still be mounted on
the side return air access panel, per the
instructions above, to insure moisture is not
drawn into the unit during operation. The covering over the mounting holes only need be
removed. Do not remove the opening cover.
19
127915-YIM-A-0405
COMPRESSORS
Units are shipped with compressor mountings factoryadjusted and ready for operation.
Do not loosen compressor mounting bolts.
FILTERS
FIGURE 3 - FIXED OUTDOOR AIR DAMPER
CONDENSATE DRAIN
Two-inch filters are supplied with each unit, but units
can be converted easily to four-inch filters. Filters must
always be installed ahead of the evaporator coil and
must be kept clean or replaced with same size and
type. Dirty filters will reduce the capacity of the unit and
will result in frosted coils or safety shutdown. Minimum
filter area and required sizes are shown in Physical
Data Table 7.
Plumbing must conform to local codes. Use a sealing
compound on male pipe threads. Install a condensate
drain line from the one-inch NPT female connection on
the unit to an open drain.
SERVICE ACCESS
NOTE: The condensate drain operates in a negative
pressure in the cabinet. The condensate drain
line MUST be trapped to provide proper drainage. See Figure 4.
•
•
•
•
The following removable panels provide access to all
serviceable components:
•
•
•
•
Compressor compartment
Electric Heat compartment
Gas Heat compartment (Two panels)
Side Supply & Return Air compartments
(Two panels)
Blower compartment (Three panels)
Main control box
Filter compartment
Outdoor Air compartment (Two panels)
Refer to the Dimensions and Clearances Figure 12 for
location of these access panels.
FIGURE 4 - RECOMMENDED DRAIN PIPING
20
Make sure that all screws and panel latches
are replaced and properly positioned on the
unit to maintain an airtight seal.
Unitary Products Group
127915-YIM-A-0405
THERMOSTAT
TERMINALS
1
( RCB )
REHEAT
CONTROL BOARD
RC
RH
R
Y1
Y1
Y2
Y2
W1
W1
W2
W2
G
G
C
C
X1
OCC
X3
TERMINAL BLOCK
RH
2
X4
A1
HUM
1
A2
HUM
2
T
DEHUMIDISTAT 3
3
T
4
TO REMOTE SENSOR
2ET04701324 IF USED
1 Electronic programmable Thermostat 2ET0770010024
( includes subbase).
2 Terminals A1 and A2 provide a relay output to close the
outdoor economizer dampers when the thermostat
switches to the set-back position.
3
Dehumidistat closes on rise in humidity.
TYPICAL
THERMOSTAT
RC
R
RH
Y1
Y1
Y2
Y2
G
G
W1
W1
W2
W2
OCC
C
C
( RCB )
REHEAT
CONTROL
BOARD
TERMINAL
BLOCK
RH
1
DEHUMIDISTAT 1
2
3
4
HUM
1
Dehumidistat closes on rise in humidity.
TERMINAL BLOCK TB1
GROUND
LUG
FACTORY OR FIELD
SUPPLIED DISCONNECT
THREE
PHASE
POWER
SUPPLY
FIGURE 5 - TYPICAL FIELD WIRING
Unitary Products Group
21
127915-YIM-A-0405
THERMOSTAT
The room thermostat should be located on an inside
wall approximately 56 inches above the floor where it
will not be subject to drafts, sun exposure or heat from
electrical fixtures or appliances. Follow the manufacturer's instructions enclosed with the thermostat for
general installation procedure. A minimum of seven
color-coded insulated wires (#18 AWG) should be used
to connect the thermostat to the unit.
Refer to the Typical Field Wiring Figure 5 and to the
appropriate unit wiring diagram for control circuit and
power wiring information.
TABLE 2: CONTROL WIRE SIZES
Maximum Length1
150 Feet
Wire Size
18 AWG
1.
From the unit to the thermostat and back to the unit.
OPTIONAL ELECTRIC HEAT
POWER AND CONTROL WIRING
Field wiring to the unit must conform to provisions of
the National Electrical Code, ANSI / NFPA No. 70 (in
U.S.A.), current Canadian Electrical Code C22.1 (in
Canada) and/or local ordinances. The unit must be
electrically grounded in accordance with NEC and CEC
(as specified above) and/or local codes. Voltage tolerances, which must be maintained at the compressor
terminals, during starting and running conditions, are
indicated on the unit Rating Plate and the Unit Application Data table.
The internal wiring harness furnished with this unit is
an integral part of a CSA design certified unit. Field
alteration to comply with electrical codes should not be
required.
A fused disconnect switch should be field provided for
the unit. The switch must be separate from all other circuits. Wire entry at knockout openings require conduit
fittings to comply with NEC (in U.S.A.), CEC (in Canada) and/or local codes. If any of the wire supplied with
the unit must be replaced, replacement wire must be of
the type shown on the wiring diagram and the same
minimum gauge as the replaced wire.
Use copper conductors properly sized to carry the load.
Each unit must be wired with a separate branch circuit
fed directly from the meter panel and properly fused.
The factory-installed heaters are wired for single point
power supply. Power supply need only be brought into
the single point terminal block and thermostat wiring to
the low voltage terminal strip located in the upper portion of the unit control box.
These CSA approved heaters are located within the
central compartment of the unit with the heater elements extending into the supply air chamber. Refer to
Figure 13 for access panel location.
Fuses are supplied, where required, by the factory.
Some KW sizes require fuses and others do not. Refer
to Table 3 for minimum CFM limitations and to Tables 8
and 9 for electrical data.
TABLE 3: ELECTRIC HEAT APPLICATION DATA
MINIMUM CFM UNIT SIZE
NOMINAL
HEATER
SIZE (KW)
VOLTAGE
3-PHASE,
60 HZ
15 TON
18
208/230,460,575
4500
36
208/230,460,575
4500
208/230
5000
460,575
4500
208/230
5000
460,575
4500
54
20 TON
25 TON
6000
7500
72
OPTIONAL GAS HEAT
When connecting electrical power and control
wiring to the unit, waterproof type connectors
MUST BE USED so that water or moisture
cannot be drawn into the unit during normal
operation. The above waterproofing conditions
will also apply when installing a field-supplied
disconnect switch.
22
These gas-fired heaters have aluminized-steel or
optional stainless steel, tubular heat exchangers with
spark ignition with proven pilot.
All gas heaters are shipped from the factory equipped
for natural gas use, but can be field converted to L.P./
Propane with Kit Model # 1NP0418. See Gas Heat
Application Data Table.
Unitary Products Group
127915-YIM-A-0405
TABLE 4: GAS HEAT APPLICATION DATA
2,000 To
4,500 Feet
Above
Sea Level
0 To
2,000 Feet
Above
Sea Level
Output Capacity (Mbh)
0 To
2,000 Feet
Above
Sea Level
2,000 To
4,500 Feet
Above
Sea Level
Available
on Models
Natural
Gas
Rate
(Ft./Hr.)
Temp.
Rise ºF
At
Full Input
Max.
Min.
Max.
Min.
Max.
Max.
Min.
Max.
300
150
270
135
240
213
15, 20 & 25 Ton
279
20
50
400
200
360
180
320
281
15, 20 & 25 Ton
372
30
60
GAS PIPING
GAS CONNECTION
Proper sizing of gas piping depends on the cubic feet
per hour of gas flow required, specific gravity of the gas
and the length of run. "National Fuel Gas Code" Z223.1
(in U.S.A.) or the current Gas Installation Codes CSAB149.1 (in Canada) should be followed in all cases
unless superseded by local codes or gas utility requirements. Refer to the Pipe Sizing Table 5.
The gas supply line can be routed through the knockouts located on the front of the unit or through the
opening provided in the unit's base. Refer to the
Dimensions and Clearances Figure 13 to locate these
access openings. Typical supply piping arrangements
are shown in the figures on page 24. All shaded items
are field-supplied.
The heating value of the gas may differ with locality.
The value should be checked with the local gas utility.
If gas supply line is routed through the unit's base
ensure that the burner assembly can be removed for
maintenance without disturbing the supply line. The
supply piping and fittings must lie below the bottom gas
manifold to avoid interference with the burner assembly.
NOTE: There may be a local gas utility requirement
specifying a minimum diameter for gas piping.
All units require a one-inch pipe connection at
the entrance fitting.
TABLE 5: PIPE SIZING
Length in Feet
Nominal Iron Pipe Size
1 in.
1-1/4 in.
10
520
1,050
20
350
730
30
285
590
40
245
500
50
215
440
60
195
400
70
180
370
80
170
350
90
160
320
100
150
305
Maximum capacity of pipe in cubic feet of gas per hour. (Based upon
a pressure drop of 0.3 inch water column and 0.6 specific gravity
gas).
Unitary Products Group
Two grommets are shipped in the blower compartment
(in parts bag taped to the blower housing) of every unit
with gas heat and should be used in the knockouts
when the gas piping penetrates the front of the unit.
After the gas supply piping has been installed, the bottom opening in the unit should be sealed to prevent
water from leaking into the building.
Gas piping recommendations:
1. A drip leg and a ground joint union must be
installed in the gas piping.
2. When required by local codes, a manual shut-off
valve may have to be installed outside of the unit.
3. Use wrought iron or steel pipe for all gas lines. Pipe
compound should be applied sparingly to male
threads only.
23
127915-YIM-A-0405
Natural gas may contain some propane. Propane, being an excellent solvent, will quickly
dissolve white lead or most standard commercial compounds. Therefore, a special pipe
compound must be applied when wrought iron
or steel pipe is used. Shellac base compounds
such as Gaskolac or Stalastic, and compounds
such as Rectorseal #5, Clyde's or John Crane
may be used.
7. A 1/8 inch NPT plugged tap, accessible for test
gage connection, must be installed immediately
upstream of the gas supply connection to the furnace.
4. All piping should be cleaned of dirt and scale by
hammering on the outside of the pipe and blowing
out the loose dirt and scale. Before initial start-up,
be sure that all of the gas lines external to the unit
have been purged of air.
5. The gas supply should be a separate line and
installed in accordance with all safety codes as
prescribed under "Limitations". After the gas connections have been completed, open the main
shut-off valve admitting normal gas pressure to the
mains. Check all joints for leaks with soap solution
or other material suitable for the purpose. NEVER
USE A FLAME.
FIGURE 6 - EXTERNAL SUPPLY CONNECTION
EXTERNAL SHUT-OFF
FIRE OR EXPLOSION HAZARD
Failure to follow the safety warning exactly
could result in serious injury, death or property
damage.
Never test for gas leaks with an open flame.
Use a commerically available soap solution
made specifically for the detection of leaks to
check all connections. A fire or explosion may
result causing property damage, personal
injury or loss of life.
6. The furnace and its individual manual shut-off
valve must be disconnected from the gas supply
piping system during any pressure testing of that
system at test pressures in excess of 1/2 psig
(3.48kPa).
The furnace must be isolated from the gas supply
piping system by closing its individual manual shutoff valve during any pressure testing of the gas
supply piping system at test pressures equal to or
less than 1/2 psig (3.48kPa).
24
FIGURE 7 - BOTTOM SUPPLY CONNECTION
EXTERNAL SHUT-OFF
L.P. UNITS, TANKS AND PIPING
All gas heat units are shipped from the factory
equipped for natural gas use only. The unit may be
converted in the field for use with L.P./propane gas
with accessory kit model number 1NP0418.
All L.P./propane gas equipment must conform to the
safety standards of the National Fire Protection Association.
For satisfactory operation, L.P./propane gas pressure
must be 8.8 I.W.C. at the unit manifold under full load.
Maintaining proper gas pressure depends on three
main factors:
Unitary Products Group
127915-YIM-A-0405
1. The vaporization rate depends on (a) the temperature of the liquid and (b) the "wetted surface" area
of the container or containers.
hood to the panel. The top flange of this hood slips in
under the top of the access panel opening when installing. Refer to Vent and Combustion Air Hood Figure 8.
2. The proper pressure regulation. (Two-stage regulation is recommended from the standpoint of both
cost and efficiency.)
Each vent hood is installed by inserting the top flange
of the hood into the slotted opening in the access panel
and securing in place.
3. The pressure drop in the lines between regulators
and between the second stage regulator and the
appliance. Pipe size required will depend on the
length of the pipe run and the total load of all appliances.
The products of combustion are discharged horizontally through these two screened, hooded vent openings on the upper gas heat access panel.
Complete information regarding tank sizing for vaporization, recommended regulator settings, and pipe sizing is available from most regulator manufacturers and
L.P./propane gas suppliers.
L.P./propane gas is an excellent solvent and special
pipe compound must be used when assembling piping
for this gas as it will quickly dissolve white lead or most
standard commercial compounds. Shellac base compounds such as Rectorseal #5 are satisfactory for this
type of gas.
Check all connections for leaks when piping is completed, using a soap solution. NEVER USE A FLAME.
VENT AIR
OUTLET
HOODS
COMBUSTION
AIR INTAKE
HOOD
SLOTTED
OPENINGS IN
ACCESS PANEL
GAS HEAT
ACCESS
PANELS
FIGURE 8 - VENT AND COMBUSTION AIR HOOD
FIRE OR EXPLOSION HAZARD
Failure to follow the safety warning exactly
could result in serious injury, death or property
damage.
Never test for gas leaks with an open flame.
Use a commerically available soap solution
made specifically for the detection of leaks to
check all connections. A fire or explosion may
result causing property damage, personal
injury or loss of life.
VENT AND COMBUSTION AIR HOODS
Two vent hoods and a combustion air hood (with
screens) are shipped attached to the blower housing in
the blower compartment. These hoods must be
installed to assure proper unit function. All hoods must
be fastened to the outside of the gas heat access panel
with the screws provided in the bag also attached to
the blower housing.
The screen for the combustion air intake hood is
secured to the inside of the access panel opening with
four fasteners and the screws used for mounting the
Unitary Products Group
An adhesive backed label is provided over the
outside of the combustion air inlet opening to
prevent moisture from entering the unit, which
could cause damage to electrical components.
Allow this closure label to remain in place until
the combustion air hood is to be installed.
OPTIONAL ECONOMIZER/MOTORIZED DAMPER RAIN
HOOD
The instruction for the optional economizer/motorized
damper rain hood can be found in form 035-19854000. Use these instructions when field assembling an
economizer rain hood onto a unit. The outdoor and
return air dampers, the damper actuator, the damper
linkage, the outdoor and return air divider baffles, and
all the control sensors are factory mounted as part of
the "Factory installed" economizer option.
25
127915-YIM-A-0405
OPTIONAL POWER EXHAUST/BAROMETRIC RELIEF
DAMPER AND RAIN HOOD
The instructions for the power exhaust/barometric relief
damper and rain hood can be found in form 03519856-000. The exhaust fan, all supporting brackets,
angles, and the wiring are factory installed as part of
the power exhaust option.
All of the components, including the dampers, hardware, and mounting instructions are shipped in a single
package external from the unit. The hood must be field
assembled and installed.
Power exhaust is not available as a field installed
option.
•
For a single enthalpy operation carefully turn the
setpoint adjusting screw (found on the damper
control module) to the "A", "B", "C" or "D" setting
corresponding to the lettered curve of the Enthalpy
Setpoint Adjustment Figure 9.
•
For a dual enthalpy operation, carefully turn the
setpoint adjusting screw fully clockwise past the
"D" setting.
POWER EXHAUST DAMPER SETPOINT (WITH OR WITHOUT POWER EXHAUST)
•
With no power exhaust option, adjust the Exhaust
Air Adjustment Screw fully clockwise. This will
allow 2nd stage cooling to operate.
•
With power exhaust option, each building pressurization requirement will be different. The point at
which the power exhaust comes on is determined
by the economizer damper position (Percent
Open). The Exhaust Air Adjustment Screw should
be set at the Percent Open of the economizer
damper at which the power exhaust is needed. It
can be set from 0 to 100% damper open.
OPTIONAL ECONOMIZER AND POWER EXHAUST
DAMPER SETPOINT ADJUSTMENTS AND INFORMATION
Remove the economizer access panel from the unit.
Loosen but do not remove the two panel latches.
Locate the economizer control module, where the following adjustments will be made.
INDOOR AIR QUALITY
Extreme care must be excercised in turning all
setpoint, maximum, and minimum damper
positioning adjustment screws to prevent twisting them off.
Check that the damper blades move smoothly without
binding; carefully turn the Minimum Position Adjusting
screw (found on the damper control module) fully
clockwise and then set the thermostat indoor fan switch
to the on position and then off, or energize and deenergize terminals "R" to "G".
MINIMUM POSITION ADJUSTMENT
With thermostat set to indoor fan on position, or terminals "R" to "G" energized, turn the Minimum Position
Adjusting screw (located on the damper control module) counterclockwise until the desired minimum
damper position has been attained.
Indoor Air quality (indoor sensor input): Terminal AQ
accepts a +2 to +10 Vdc signal with respect to the
(AQ1) terminal. When the signal is below it's setpoint,
the actuator is allowed to modulate normally in accordance with the enthalpy and mixed air sensor inputs.
When the AQ signal exceeds it's setpoint setting and
there is no call for free cooling, the actuator is proportionately modulated from the 2 to 10 Vdc signal, with 2
Vdc corresponding to full closed and 10 Vdc corresponding to full open. When there is no call for free
cooling, the damper position is limited by the IAQ Max
damper position setting. When the signal exceeds it's
setpoint (Demand Control Ventilation Setpoint) setting
and there is a call for free cooling, the actuator modulates from the minimum position to the full open position based on the highest call from either the mixed air
sensor input or the AQ voltage input.
•
•
Optional CO2 Space Sensor Kit Part #
2AQ04700224
Optional CO2 Sensor Kit Part # 2AQ04700124
Replace the economizer access panel.
ENTHALPY SETPOINT ADJUSTMENT
The enthalpy setpoint may now be set by selecting the
desired setpoint shown in the Enthalpy Setpoint Adjustment Figure 9. Adjust as follows:
26
Unitary Products Group
127915-YIM-A-0405
CONTROL
CURVE
CONTROL POINT
APPROX. 0F (0C)
AT 50% RH
A
73 (23)
B
C
70 (21)
67 (19)
D
63 (17)
85 90 95 100 105 110
(29) (32) (35) (38) (41) (43)
80
(27)
75
(24)
70
(21)
65
(18)
60
(16)
55
(13)
50
(10)
45
(7)
35
(2)
A
B
C
D
40
(4)
B
D C
35
(2)
40
(4)
45
(7)
A
50 55 60 65 70 75 80 85 90 95 100 105 110
(10) (13) (16) (18) (21) (24) (27) (29) (32) (35) (38) (41) (43)
APPROXIMATE DRY BULB TEMPERATURE - 0F (0C)
FIGURE 9 - ENTHALPY SETPOINT ADJUSTMENT
Exhaust Air
Adjustment
Screw
Exhaust Air LED
Damper Min.
Position
Screw
Indoor Air Quality
Max. Adjustment
Screw
N1
N
EXH
Set
TR
P1
P
EXH
24
Vac
HOT
T1
T
Min
Pos
IAQ
Max
Indoor Air Quality
LED
AQ1
AQ
IAQ
SO
IAQ
Min
TR1
24
Vac
COM
+
1
2
5
Indoor Air Quality
Min. Adjustment
Screw
Free Cooling LED
SO+
3
4
EF
EF1
Free
Cool
SR+
SR
B
A
C
D
Economizer Enthalpy
Set Point Adjustment
Screw
FIGURE 10 - HONEYWELL ECONOMIZER CONTROL W7212
Unitary Products Group
27
127915-YIM-A-0405
TABLE 6: FOUR AND SIX POINT LOADS
4 Point Loads (lbs)
Unit Size
Operating
Weight1
A
B
C
D
180 Gas
2850
486
908
948
508
240 Gas
3150
549
1026
1026
549
300 Gas
3250
567
1058
1058
567
180 Elec
2650
452
844
882
472
240 Elec
2950
514
961
961
514
300 Elec
3050
532
993
993
532
Unit Size
Operating
Weight1
A
B
C
D
E
F
180 Gas
2850
324
338
485
632
605
465
240 Gas
3150
366
366
525
684
684
525
300 Gas
3250
378
378
542
706
706
542
180 Elec
2650
301
315
451
588
563
432
240 Elec
2950
343
343
492
641
641
492
300 Elec
3050
354
354
508
662
662
508
1.
6 Point Loads (lbs)
Weight includes unit, economizer, economizer rain hood and high option heat (gas or electric).
B
F
E
C
D
C
A
A
D
B
FIGURE 11 - FOUR AND SIX POINT LOADS
28
Unitary Products Group
127915-YIM-A-0405
TABLE 7: PHYSICAL DATA
MODELS
EVAPORATOR
BLOWER
DR 180
CENTRIFUGAL BLOWER (Dia. x Wd.)
15x15
FAN MOTOR HP
5/7.5
DR 240
18x15
7.5/10
ROWS DEEP
EVAPORATOR
COIL
13.5
20
PROPELLER DIA. (In.)
CONDENSER FAN
FAN MOTOR HP
(FOUR PER UNIT)
NOM. CFM TOTAL
(Each)
FILTERS
CHARGE
30
(Each)
1/3
3/4
(Each)
4,000
5,000
ROWS DEEP
2
FINS PER INCH
20
63.8
ROWS DEEP
2
FINS PER INCH
13
FACE AREA (Sq. Ft.)
COMPRESSOR
(QTY. PER UNIT)
20.52
24
FACE AREA (Sq. Ft.)
REHEAT COIL
17.2
SCROLL
2
QUANTITY PER UNIT (16” X 25” X 2”)
4
QUANTITY PER UNIT (16” X 20” X 2”)
4
TOTAL FACE AREA (Sq. Ft.)
20
REFRIGERANT 22 SYSTEM No. 1
(Lb./Oz.)
SYSTEM No. 2
22/8
27/0
25/0
22/0
27/0
24/8
2360
2660
2760
N24
2560
2860
2960
N32
2600
2900
3000
COOLING ONLY
Unitary Products Group
GAS / ELECTRIC
DOUBLE WALL
260
ECONOMIZER
160
ECONOMIZER WITH
POWER EXHAUST
245
MOTORIZED DAMPER
ELECTRIC
HEATER
ACCESSORIES
OPERATING
WEIGHTS
(LBS.)
OPTIONS
BASIC
UNIT
15.0
4
FINS PER INCH
FACE AREA (Sq. Ft.)
CONDENSER
COIL
DR 300
150
18 KW
25
36 KW
30
54 KW
35
72 KW
40
ROOF CURB
185
BAROMETRIC DAMPER
45
ECONOMIZER / MOTORIZED
DAMPER RAIN HOOD
55
ECONOMIZER / POWER
EXHAUST RAIN HOOD
90
WOOD SKID
220
29
127915-YIM-A-0405
TABLE 8: DR ELECTRICAL DATA - STANDARD DRIVE MOTOR W/O POWERED CONVENIENCE OUTLET
COMPRESSORS
MODEL
TONNAGE
VOLTAGE
RLA
EACH
OD FAN
MOTORS
FLA EACH
LRA
EACH
ID
BLOWER
MOTOR
FLA
CONV
OUTLET
AMPS
208
22.4
164
2.1
15.4
0.0
230
22.4
164
2.1
15.4
0.0
460
10.9
100
1.1
7.2
0.0
575
8.3
78
0.9
5.9
0.0
208
33.6
225
3.7
20.0
0.0
230
33.6
225
3.7
20.0
0.0
460
17.3
114
1.9
10.0
0.0
575
13.5
80
1.5
8.2
0.0
208
47.1
245
3.7
38.6
0.0
230
47.1
245
3.7
38.6
0.0
460
19.6
125
1.9
19.3
0.0
575
15.8
100
1.5
15.4
0.0
15
20
25
HEATER OPTION
MODEL
KW
STAGES
AMPS
None
E18
E36
E54
E72
None
E18
E36
E54
E72
None
E18
E36
E54
E72
None
E18
E36
E54
E72
None
E18
E36
E54
E72
None
E18
E36
E54
E72
None
E18
E36
E54
E72
None
E18
E36
E54
E72
None
E18
E36
E54
E72
None
E18
E36
E54
E72
None
E18
E36
E54
E72
None
E18
E36
E54
E72
0.0
13.5
27.0
40.6
54.1
0.0
18.0
36.0
54.0
72.0
0.0
18.0
36.0
54.0
72.0
0.0
18.0
36.0
54.0
72.0
0.0
13.5
27.0
40.6
54.1
0.0
18.0
36.0
54.0
72.0
0.0
18.0
36.0
54.0
72.0
0.0
18.0
36.0
54.0
72.0
0.0
13.5
27.0
40.6
54.1
0.0
18.0
36.0
54.0
72.0
0.0
18.0
36.0
54.0
72.0
0.0
18.0
36.0
54.0
72.0
1
2
2
2
1
2
2
2
1
2
2
2
1
2
2
2
1
2
2
2
1
2
2
2
1
2
2
2
1
2
2
2
1
2
2
2
1
2
2
2
1
2
2
2
1
2
2
2
37.5
75.1
112.6
150.1
43.3
86.6
129.9
173.2
21.7
43.3
65.0
86.6
17.3
34.6
52.0
69.3
37.5
75.1
112.6
150.1
43.3
86.6
129.9
173.2
21.7
43.3
65.0
86.6
17.3
34.6
52.0
69.3
37.5
75.1
112.6
150.1
43.3
86.6
129.9
173.2
21.7
43.3
65.0
86.6
17.3
34.6
52.0
69.3
MAX. FUSE/
MIN.
CIRCUIT
BRKR1
AMPACITY
SIZE
(AMPS)
(AMPS)
74.2
90
74.2
90
112.9
125
160.1
175
169.4
200
73.2
90
73.2
90
126.3
150
147.9
175
191.2
225
36.1
45
36.1
45
63.1
70
74.0
90
95.6
110
28.2
35
29.0
35
50.7
60
59.3
70
76.7
90
110.4
125
110.4
125
118.7
125
165.9
175
175.2
200
110.4
125
110.4
125
133.3
150
154.9
175
198.2
225
56.5
70
56.5
70
66.6
70
77.5
90
99.1
110
44.6
50
44.6
50
53.6
60
62.2
70
79.5
90
159.4
200
159.4
200
159.4
200
189.1
200
198.4
225
159.4
200
159.4
200
159.4
200
178.2
200
221.5
250
71.0
90
71.0
90
78.3
90
89.1
100
110.7
125
57.0
70
57.0
70
62.6
70
71.2
80
88.5
100
NOTE 1: HACR Type per NEC.
VOLTAGE LIMITATIONS
POWER SUPPLY
VOLTAGE
LIMITATIONS1
1.
30
208/230-3-60
460-3-60
565-3-60
MIN.
187
414
518
VOLTAGE
MAX.
253
506
630
ELECTRIC HEAT CORRECTION FACTORS
NOMINAL VOLTAGE
VOLTAGE
kW CAP. MULTIPLIER
208
208
1.00
240
230
0.92
480
460
0.92
600
575
0.92
Utilization Range “A” in accordance with ARI Standard 110.
Unitary Products Group
127915-YIM-A-0405
TABLE 9: DR ELECTRICAL DATA - HIGH STATIC DRIVE MOTOR W/O POWERED CONVENIENCE OUTLET
COMPRESSORS
MODEL
TONNAGE
VOLTAGE
RLA
EACH
OD FAN
MOTORS
FLA EACH
LRA
EACH
ID
BLOWER
MOTOR
FLA
CONV
OUTLET
AMPS
208
22.4
164
2.1
20
0.0
230
22.4
164
2.1
20
0.0
460
10.9
100
1.1
10
0.0
575
8.3
78
0.9
8.2
0.0
208
33.6
225
3.7
28
0.0
230
33.6
225
3.7
26.6
0.0
460
17.3
114
1.9
13.3
0.0
575
13.5
80
1.5
10.3
0.0
208
47.1
245
3.7
38.6
0.0
230
47.1
245
3.7
38.6
0.0
460
19.6
125
1.9
19.3
0.0
575
15.8
100
1.5
15.4
0.0
15
20
25
HEATER OPTION
MODEL
KW
STAGES
AMPS
None
E18
E36
E54
E72
None
E18
E36
E54
E72
None
E18
E36
E54
E72
None
E18
E36
E54
E72
None
E18
E36
E54
E72
None
E18
E36
E54
E72
None
E18
E36
E54
E72
None
E18
E36
E54
E72
None
E18
E36
E54
E72
None
E18
E36
E54
E72
None
E18
E36
E54
E72
None
E18
E36
E54
E72
0.0
13.5
27.0
40.6
54.1
0.0
18.0
36.0
54.0
72.0
0.0
18.0
36.0
54.0
72.0
0.0
18.0
36.0
54.0
72.0
0.0
13.5
27.0
40.6
54.1
0.0
18.0
36.0
54.0
72.0
0.0
18.0
36.0
54.0
72.0
0.0
18.0
36.0
54.0
72.0
0.0
13.5
27.0
40.6
54.1
0.0
18.0
36.0
54.0
72.0
0.0
18.0
36.0
54.0
72.0
0.0
18.0
36.0
54.0
72.0
1
2
2
2
1
2
2
2
1
2
2
2
1
2
2
2
1
2
2
2
1
2
2
2
1
2
2
2
1
2
2
2
1
2
2
2
1
2
2
2
1
2
2
2
1
2
2
2
37.5
75.1
112.6
150.1
43.3
86.6
129.9
173.2
21.7
43.3
65.0
86.6
17.3
34.6
52.0
69.3
37.5
75.1
112.6
150.1
43.3
86.6
129.9
173.2
21.7
43.3
65.0
86.6
17.3
34.6
52.0
69.3
37.5
75.1
112.6
150.1
43.3
86.6
129.9
173.2
21.7
43.3
65.0
86.6
17.3
34.6
52.0
69.3
MAX. FUSE/
MIN.
CIRCUIT
BRKR1
AMPACITY
SIZE
(AMPS)
(AMPS)
78.8
100
78.8
100
118.7
125
165.9
175
175.2
200
78.8
100
79.1
100
133.3
150
154.9
175
198.2
225
38.9
45
39.6
45
66.6
70
77.5
90
99.1
110
30.5
35
31.9
35
53.6
60
62.2
70
79.5
90
117
150
117
150
126.9
150
174.1
175
183.4
200
117
150
117
150
141.5
150
163.2
175
206.5
225
59.8
70
59.8
70
70.8
80
81.6
90
103.2
110
46.7
60
46.7
60
56.2
60
64.8
70
82.2
90
159.4
200
159.4
200
159.4
200
189.1
200
198.4
225
159.4
200
159.4
200
159.4
200
178.2
200
221.5
250
71.0
90
71.0
90
78.3
90
89.1
100
110.7
125
57.0
70
57.0
70
62.6
70
71.2
80
88.5
100
NOTE 1: HACR Type per NEC.
VOLTAGE LIMITATIONS
POWER SUPPLY
VOLTAGE
LIMITATIONS1
1.
208/230-3-60
460-3-60
565-3-60
MIN.
187
414
518
VOLTAGE
MAX.
253
506
630
ELECTRIC HEAT CORRECTION FACTORS
NOMINAL VOLTAGE
VOLTAGE
kW CAP. MULTIPLIER
208
208
1.00
240
230
0.92
480
460
0.92
600
575
0.92
Utilization Range “A” in accordance with ARI Standard 110.
Unitary Products Group
31
127915-YIM-A-0405
TABLE 10: DR ELECTRICAL DATA - LOW AIRFLOW DRIVE MOTOR W/O POWERED CONVENIENCE OUTLET
COMPRESSORS
MODEL
TONNAGE
VOLTAGE
RLA
EACH
OD FAN
MOTORS
FLA EACH
LRA
EACH
ID
BLOWER
MOTOR
FLA
CONV
OUTLET
AMPS
208
47.1
245
3.7
20.0
0.0
230
47.1
245
3.7
20.0
0.0
460
19.6
125
1.9
10.0
0.0
575
15.8
100
1.5
8.2
0.0
25
HEATER OPTION
MODEL
KW
STAGES
AMPS
None
E18
E36
E54
E72
None
E18
E36
E54
E72
None
E18
E36
E54
E72
None
E18
E36
E54
E72
0.0
13.5
27.0
40.6
54.1
0.0
18.0
36.0
54.0
72.0
0.0
18.0
36.0
54.0
72.0
0.0
18.0
36.0
54.0
72.0
1
2
2
2
1
2
2
2
1
2
2
2
1
2
2
2
37.5
75.1
112.6
150.1
43.3
86.6
129.9
173.2
21.7
43.3
65.0
86.6
17.3
34.6
52.0
69.3
MAX. FUSE/
MIN.
CIRCUIT
BRKR1
AMPACITY
SIZE
(AMPS)
(AMPS)
140.8
175
140.8
175
140.8
175
165.9
175
175.2
200
140.8
175
140.8
175
140.8
175
154.9
175
198.2
225
61.7
80
61.7
80
66.6
80
77.5
90
99.1
110
49.8
60
49.8
60
53.6
60
62.2
70
79.5
90
NOTE 1: HACR Type per NEC.
VOLTAGE LIMITATIONS
POWER SUPPLY
VOLTAGE
LIMITATIONS1
1.
32
208/230-3-60
460-3-60
565-3-60
MIN.
187
414
518
VOLTAGE
MAX.
253
506
630
ELECTRIC HEAT CORRECTION FACTORS
NOMINAL VOLTAGE
VOLTAGE
kW CAP. MULTIPLIER
208
208
1.00
240
230
0.92
480
460
0.92
600
575
0.92
Utilization Range “A” in accordance with ARI Standard 110.
Unitary Products Group
127915-YIM-A-0405
TABLE 11: DR ELECTRICAL DATA - STANDARD DRIVE MOTOR WITH POWERED CONVENIENCE OUTLET
COMPRESSORS
MODEL
TONNAGE
VOLTAGE
RLA
EACH
OD FAN
MOTORS
FLA EACH
LRA
EACH
ID
BLOWER
MOTOR
FLA
CONV
OUTLET
AMPS
208
22.4
164
2.1
15.4
10.0
230
22.4
164
2.1
15.4
10.0
460
10.9
100
1.1
7.2
5.0
575
8.3
78
0.9
5.9
4.0
208
33.6
225
3.7
20.0
10.0
230
33.6
225
3.7
20.0
10.0
460
17.3
114
1.9
10.0
5.0
575
13.5
80
1.5
8.2
4.0
208
47.1
245
3.7
38.6
10.0
230
47.1
245
3.7
38.6
10.0
460
19.6
125
1.9
19.3
5.0
575
15.8
100
1.5
15.4
4.0
15
20
25
HEATER OPTION
MODEL
KW
STAGES
AMPS
None
E18
E36
E54
E72
None
E18
E36
E54
E72
None
E18
E36
E54
E72
None
E18
E36
E54
E72
None
E18
E36
E54
E72
None
E18
E36
E54
E72
None
E18
E36
E54
E72
None
E18
E36
E54
E72
None
E18
E36
E54
E72
None
E18
E36
E54
E72
None
E18
E36
E54
E72
None
E18
E36
E54
E72
0.0
13.5
27.0
40.6
54.1
0.0
18.0
36.0
54.0
72.0
0.0
18.0
36.0
54.0
72.0
0.0
18.0
36.0
54.0
72.0
0.0
13.5
27.0
40.6
54.1
0.0
18.0
36.0
54.0
72.0
0.0
18.0
36.0
54.0
72.0
0.0
18.0
36.0
54.0
72.0
0.0
13.5
27.0
40.6
54.1
0.0
18.0
36.0
54.0
72.0
0.0
18.0
36.0
54.0
72.0
0.0
18.0
36.0
54.0
72.0
1
2
2
2
1
2
2
2
1
2
2
2
1
2
2
2
1
2
2
2
1
2
2
2
1
2
2
2
1
2
2
2
1
2
2
2
1
2
2
2
1
2
2
2
1
2
2
2
37.5
75.1
112.6
150.1
43.3
86.6
129.9
173.2
21.7
43.3
65.0
86.6
17.3
34.6
52.0
69.3
37.5
75.1
112.6
150.1
43.3
86.6
129.9
173.2
21.7
43.3
65.0
86.6
17.3
34.6
52.0
69.3
37.5
75.1
112.6
150.1
43.3
86.6
129.9
173.2
21.7
43.3
65.0
86.6
17.3
34.6
52.0
69.3
MAX. FUSE/
MIN.
CIRCUIT
BRKR1
AMPACITY
SIZE
(AMPS)
(AMPS)
84.2
100
84.2
100
125.4
150
172.6
175
181.9
200
83.2
100
84.6
100
138.8
150
160.4
175
203.7
225
41.1
50
42.3
50
69.4
70
80.2
90
101.9
110
32.2
40
34.0
40
55.7
60
64.3
70
81.7
90
120.4
150
120.4
150
131.2
125
178.4
200
187.7
200
120.4
150
120.4
150
145.8
150
167.4
175
210.7
225
61.5
70
61.5
70
72.9
80
83.7
90
105.4
110
48.6
60
48.6
60
58.6
60
67.2
70
84.5
90
169.4
200
169.4
200
169.4
200
201.6
225
210.9
225
169.4
200
169.4
200
169.4
200
190.7
225
234.0
250
76.0
90
76.0
90
84.5
90
95.3
110
117.0
125
61.0
70
61.0
70
67.6
70
76.2
90
93.5
100
NOTE 1: HACR Type per NEC.
VOLTAGE LIMITATIONS
POWER SUPPLY
VOLTAGE
LIMITATIONS1
1.
208/230-3-60
460-3-60
565-3-60
MIN.
187
414
518
VOLTAGE
MAX.
253
506
630
ELECTRIC HEAT CORRECTION FACTORS
NOMINAL VOLTAGE
VOLTAGE
kW CAP. MULTIPLIER
208
208
1.00
240
230
0.92
480
460
0.92
600
575
0.92
Utilization Range “A” in accordance with ARI Standard 110.
Unitary Products Group
33
127915-YIM-A-0405
TABLE 12: DR ELECTRICAL DATA - HIGH STATIC DRIVE MOTOR WITH POWERED CONVENIENCE OUTLET
COMPRESSORS
MODEL
TONNAGE
VOLTAGE
RLA
EACH
OD FAN
MOTORS
FLA EACH
LRA
EACH
ID
BLOWER
MOTOR
FLA
CONV
OUTLET
AMPS
208
22.4
164
2.1
20
10.0
230
22.4
164
2.1
20
10.0
460
10.9
100
1.1
10
5.0
575
8.3
78
0.9
8.2
4.0
208
33.6
225
3.7
28
10.0
230
33.6
225
3.7
26.6
10.0
460
17.3
114
1.9
13.3
5.0
575
13.5
80
1.5
10.3
4.0
208
47.1
245
3.7
38.6
10.0
230
47.1
245
3.7
38.6
10.0
460
19.6
125
1.9
19.3
5.0
575
15.8
100
1.5
15.4
4.0
15
20
25
HEATER OPTION
MODEL
KW
STAGES
AMPS
None
E18
E36
E54
E72
None
E18
E36
E54
E72
None
E18
E36
E54
E72
None
E18
E36
E54
E72
None
E18
E36
E54
E72
None
E18
E36
E54
E72
None
E18
E36
E54
E72
None
E18
E36
E54
E72
None
E18
E36
E54
E72
None
E18
E36
E54
E72
None
E18
E36
E54
E72
None
E18
E36
E54
E72
0.0
13.5
27.0
40.6
54.1
0.0
18.0
36.0
54.0
72.0
0.0
18.0
36.0
54.0
72.0
0.0
18.0
36.0
54.0
72.0
0.0
13.5
27.0
40.6
54.1
0.0
18.0
36.0
54.0
72.0
0.0
18.0
36.0
54.0
72.0
0.0
18.0
36.0
54.0
72.0
0.0
13.5
27.0
40.6
54.1
0.0
18.0
36.0
54.0
72.0
0.0
18.0
36.0
54.0
72.0
0.0
18.0
36.0
54.0
72.0
1
2
2
2
1
2
2
2
1
2
2
2
1
2
2
2
1
2
2
2
1
2
2
2
1
2
2
2
1
2
2
2
1
2
2
2
1
2
2
2
1
2
2
2
1
2
2
2
37.5
75.1
112.6
150.1
43.3
86.6
129.9
173.2
21.7
43.3
65.0
86.6
17.3
34.6
52.0
69.3
37.5
75.1
112.6
150.1
43.3
86.6
129.9
173.2
21.7
43.3
65.0
86.6
17.3
34.6
52.0
69.3
37.5
75.1
112.6
150.1
43.3
86.6
129.9
173.2
21.7
43.3
65.0
86.6
17.3
34.6
52.0
69.3
MAX. FUSE/
MIN.
CIRCUIT
BRKR1
AMPACITY
SIZE
(AMPS)
(AMPS)
88.8
110
88.8
110
131.2
150
178.4
200
187.7
200
88.8
110
91.6
110
145.8
150
167.4
175
210.7
225
43.9
50
45.8
50
72.9
80
83.7
90
105.4
110
34.5
40
36.9
40
58.6
60
67.2
70
84.5
90
127.0
150
127.0
150
139.4
150
186.6
200
195.9
200
127.0
150
127.0
150
154.0
175
175.7
200
219.0
225
64.8
80
64.8
80
77.0
80
87.8
90
109.5
110
50.7
60
50.7
60
61.2
70
69.8
70
87.2
90
169.4
200
169.4
200
169.4
200
201.6
225
210.9
225
169.4
200
169.4
200
169.4
200
190.7
225
234.0
250
76.0
90
76.0
90
84.5
90
95.3
110
117.0
125
61.0
70
61.0
70
67.6
70
76.2
90
93.5
100
NOTE 1: HACR Type per NEC.
VOLTAGE LIMITATIONS
POWER SUPPLY
VOLTAGE
LIMITATIONS1
1.
34
208/230-3-60
460-3-60
565-3-60
MIN.
187
414
518
VOLTAGE
MAX.
253
506
630
ELECTRIC HEAT CORRECTION FACTORS
NOMINAL VOLTAGE
VOLTAGE
kW CAP. MULTIPLIER
208
208
1.00
240
230
0.92
480
460
0.92
600
575
0.92
Utilization Range “A” in accordance with ARI Standard 110.
Unitary Products Group
127915-YIM-A-0405
TABLE 13: DR ELECTRICAL DATA - LOW AIRFLOW DRIVE MOTOR WITH POWERED CONVENIENCE OUTLET
COMPRESSORS
MODEL
TONNAGE
VOLTAGE
RLA
EACH
OD FAN
MOTORS
FLA EACH
LRA
EACH
ID
BLOWER
MOTOR
FLA
CONV
OUTLET
AMPS
208
47.1
245
3.7
20.0
10.0
230
47.1
245
3.7
20.0
10.0
460
19.6
125
1.9
10.0
5.0
575
15.8
100
1.5
8.2
4.0
25
HEATER OPTION
MODEL
KW
STAGES
AMPS
None
E18
E36
E54
E72
None
E18
E36
E54
E72
None
E18
E36
E54
E72
None
E18
E36
E54
E72
0.0
13.5
27.0
40.6
54.1
0.0
18.0
36.0
54.0
72.0
0.0
18.0
36.0
54.0
72.0
0.0
18.0
36.0
54.0
72.0
1
2
2
2
1
2
2
2
1
2
2
2
1
2
2
2
37.5
75.1
112.6
150.1
43.3
86.6
129.9
173.2
21.7
43.3
65.0
86.6
17.3
34.6
52.0
69.3
MAX. FUSE/
MIN.
CIRCUIT
BRKR1
AMPACITY
SIZE
(AMPS)
(AMPS)
150.8
175
150.8
175
150.8
175
178.4
200
187.7
200
150.8
175
150.8
175
150.8
175
167.4
175
210.7
225
66.7
80
66.7
80
72.9
80
83.7
90
105.4
110
53.8
60
53.8
60
58.6
60
67.2
70
84.5
90
NOTE 1: HACR Type per NEC.
VOLTAGE LIMITATIONS
POWER SUPPLY
VOLTAGE
LIMITATIONS1
1.
208/230-3-60
460-3-60
565-3-60
MIN.
187
414
518
VOLTAGE
MAX.
253
506
630
ELECTRIC HEAT CORRECTION FACTORS
NOMINAL VOLTAGE
VOLTAGE
kW CAP. MULTIPLIER
208
208
1.00
240
230
0.92
480
460
0.92
600
575
0.92
Utilization Range “A” in accordance with ARI Standard 110.
Unitary Products Group
35
127915-YIM-A-0405
<@ <
@ <1
;> 1
>: :
) 0
<
0
<1< &= !%
0
86 34
<1
) >
58 5
1
;! -!&!
!- ! *
: ? :
$66
<0
:
11
345
9 8
47 5
748
5728
0
>
:
298
0 1
42
0
< 11
1
)
42 5
44
#+ - ! )% ) &)! )
0)) &") -*$ 1+!
1-* ")
" )$
11
;! "&!' &) &)B !,! ) )# "&!' # *!
, )# "&!' ,! -!-! C , )#
&--% !)&! ! &") "")$
445
0 1
8
A
5728
! "#$ #% !
&'(") ) "# * +)#&) )"$
!), + ' -!.
&- !/&)$
11
45
0 3
2
8 8
3 5
345
CLEARANCES
Front
UTILITIES ENTRY DATA
HOLE
A
B
C
D
OPENING
SIZE
(DIA.)
1-1/8" KO
3/4" NPS (Fem.)
3-5/8" KO
3" NPS (Fem.)
2-3/8" KO
1-11/16" Hole
Rear
Left Side (Filter Access)
USED FOR
Control Front
Wiring
Bottom
Front
Power
Wiring
Bottom
Gas Piping (Front)
Gas Piping (Bottom)*
*Opening in the bottom of the unit can be located by the slice
in the insulation.
Right Side (Cond. Coil)
Below Unit1
Above Unit2
36"
24"
49"
24"
36"
36"
(Less Economizer)
(With Economizer)
(Less Economizer)
(With Economizer)3
20"
72" With 36" Maximum
Horizontal Overhang
(For Condenser Air
Discharge Outlet)
1Unit s
(applicable in U.S.A. only) may be installed on combustible floors
made from wood or class A, B or C roof covering material.
Units must be installed outdoors. Overhanging structures or shrubs should
not obstruct condenser air discharge outlet.
3
If economizer is factory installed, the unassembled rainhood must be
removed from its ride-along position in front of evaporator coil, prior to
final installation. The hood kit box is 54" long.
NOTE:
A 1" clearance must be provided between any combustible material and the
supply air ductwork for a distance of 3 feet from the unit.
2
The products of combustion must not be allowed to accumulate within a
confined space and recirculate.
Locate unit so that the vent air outlet hoods are at least:
Three (3) feet above any forced air inlet located within 10 horizontal feet (excluding those integral to the unit).
Four (4) feet below, 4 horizontal feet from, or 1 foot above any door or gravity
air inlet into the building.
FIGURE 12 - DIMENSIONS & CLEARANCES 15/20/25 TON
36
Unitary Products Group
127915-YIM-A-0405
DUCT COVERS - Units are shipped with the bottom duct
openings covered. An accessory flange kit is available for
connecting side ducts.
For bottom duct applications:
1. Remove the side panels from the supply and return air
compartments to gain access to the bottom supply and
return air duct covers.
2. Remove and discard the bottom duct covers (Duct openings are closed with sheet metal covers except when the
unit includes a power exhaust option. The covering consists of a heavy black paper composition.)
3. Replace the side supply and return air compartment panels.
For side duct application:
1. Replace the side panels on the supply and return air compartments with the accessory flange kit panels.
2. Connect ductwork to the duct flanges on the rear of the
unit.
DETAIL “X”
ACCESSORY SIDE SUPPLY AND RETURN AIR OPENINGS
REAR VIEW
DETAIL "Y"
UNIT WITH RAIN HOODS
LH VIEW
FIGURE 12 - DIMENSIONS & CLEARANCES 15/20/25 TON (CONTINUED)
Unitary Products Group
37
127915-YIM-A-0405
CFM, STATIC PRESSURE, AND POWER - ALTITUDE AND TEMPERATURE CORRECTIONS
order to use the indoor blower tables for high altitude applications, certain corrections are necessary.
The information below should be used to assist in application
of product when being applied at altitudes at or exceeding
1000 feet above sea level.
A centrifugal fan is a "constant volume" device. This means
that, if the rpm remains constant, the CFM delivered is the
same regardless of the density of the air. However, since the
air at high altitude is less dense, less static pressure will be
generated and less power will be required than a similar
application at sea level. Air density correction factors are
shown in Table 14 and Figure 13.
The air flow rates listed in the standard blower performance
tables are based on standard air at sea level. As the altitude
or temperature increases, the density of air decreases. In
TABLE 14: ALTITUDE CORRECTION FACTORS
AIR TEMP
40
50
60
70
80
90
100
0
1.060
1.039
1.019
1.000
0.982
0.964
0.946
1000
1.022
1.002
0.982
0.964
0.947
0.929
0.912
2000
0.986
0.966
0.948
0.930
0.913
0.897
0.880
3000
0.950
0.931
0.913
0.896
0.880
0.864
0.848
ALTITUDE (FEET)
4000
5000
0.916
0.882
0.898
0.864
0.880
0.848
0.864
0.832
0.848
0.817
0.833
0.802
0.817
0.787
6000
0.849
0.832
0.816
0.801
0.787
0.772
0.758
7000
0.818
0.802
0.787
0.772
0.758
0.744
0.730
8000
0.788
0.772
0.757
0.743
0.730
0.716
0.703
9000
0.758
0.743
0.729
0.715
0.702
0.689
0.676
10000
0.729
0.715
0.701
0.688
0.676
0.663
0.651
The examples below will assist in determining the airflow performance of the product at altitude.
blower tables to select the blower speed and the BHP
requirement.
Example 1: What are the corrected CFM, static pressure,
and BHP at an elevation of 5,000 ft. if the blower performance
data is 6,000 CFM, 1.5 IWC and 4.0 BHP?
Solution: As in the example above, no temperature information is given so 70°F is assumed.
Solution: At an elevation of 5,000 ft the indoor blower will still
deliver 6,000 CFM if the rpm is unchanged. However, Table
14 must be used to determine the static pressure and BHP.
Since no temperature data is given, we will assume an air
temperature of 70°F. Table 14 shows the correction factor to
be 0.832.
The 1.5" static pressure given is at an elevation of 5,000 ft.
The first step is to convert this static pressure to equivalent
sea level conditions.
Sea level static pressure = 1.5 / .832 = 1.80"
Enter the blower table at 6000 sCFM and static pressure of
1.8". The rpm listed will be the same rpm needed at 5,000 ft.
Corrected static pressure = 1.5 x 0.832 = 1.248 IWC
Corrected BHP = 4.0 x 0.832 = 3.328
Example 2: A system, located at 5,000 feet of elevation, is to
deliver 6,000 CFM at a static pressure of 1.5". Use the unit
38
Suppose that the corresponding BHP listed in the table is 3.2.
This value must be corrected for elevation.
BHP at 5,000 ft = 3.2 x .832 = 2.66
Unitary Products Group
127915-YIM-A-0405
FIGURE 13 - ALTITUDE/TEMPERATURE CONVERSION FACTOR
Unitary Products Group
39
127915-YIM-A-0405
TABLE 15: DR180 BLOWER PERFORMANCE - STANDARD DRIVE (COOLING ONLY)
15 ton Standard Drive Blower Performance (Horizontal Discharge)
ESP
0.2
0.4
0.6
0.8
1.0
1.2
CFM RPM KW
BHP CFM RPM
KW
6373 931 3.343
4.01 6172
899 3.058
6013 932 3.099
3.72 5783
900 2.834
5610 935 2.840
3.41 5364
902 2.537
5205 937 2.600
3.12 4912
904 2.345
4767 938 2.371
2.85 4436
905 2.172
4268 940 2.130
2.56
1 turn
2 turns
BHP
CFM RPM
3.67 5821
868
3.40 5409
869
3.04 5016
870
2.81 4534
873
2.61 4009
874
KW
2.664
2.412
2.167
1.956
1.749
BHP CFM RPM
3.20 5591
834
2.89 5158
836
2.60 4704
837
2.35 4208
838
2.10 3598
840
3 turns
KW
2.415
2.207
1.978
1.740
1.533
4 turns
BHP CFM RPM
2.90 5332
801
2.65 4854
802
2.37 4374
804
2.09 3896
805
1.84 3175
807
KW
2.154
1.932
1.734
1.542
1.26
5 turns
BHP CFM RPM
2.59 5081
769
2.32 4597
770
2.08 4081
772
1.85 3437
773
1.51 2665
774
KW
1.859
1.661
1.464
1.235
0.987
BHP
2.23
1.99
1.76
1.48
1.18
6 turns
15-Ton Standard Drive
VP-56 & BK105
6500
1 Turn
2 Turns
6000
SCFM
3 Turns
4 Turns
5500
5 Turns
6 Turns
5000
4500
0
0.2
0.4
0.6
0.8
1
1.2
External Static ("WC)
40
Unitary Products Group
127915-YIM-A-0405
TABLE 16: DR180 BLOWER PERFORMANCE - STANDARD DRIVE (GAS HEAT)
15 ton Standard Drive Blower Performance (Horizontal Discharge)
ESP CFM RPM KW BHP CFM RPM KW BHP CFM RPM KW BHP CFM RPM KW BHP CFM RPM KW BHP CFM RPM KW BHP
0.2 6246 912 3.276 3.93 6049 881 2.997 3.60 5705 851 2.611 3.13 5479 818 2.367 2.84 5225 785 2.111 2.53 4979 754 1.822 2.19
0.4 5893 914 3.037 3.65 5667 882 2.777 3.33 5301 852 2.364 2.84 5055 819 2.163 2.60 4757 786 1.893 2.27 4505 755 1.628 1.95
0.6 5498 916 2.783 3.34 5257 883 2.486 2.98 4916 853 2.124 2.55 4610 820 1.938 2.33 4287 788 1.699 2.04 3999 757 1.435 1.72
0.8 5101 918 2.548 3.06 4814 885 2.298 2.76 4443 856 1.917 2.30 4124 821 1.705 2.05 3818 789 1.511 1.81 3368 758 1.210 1.45
1.0 4672 919 2.324 2.79 4347 887 2.129 2.55 3929 857 1.714 2.06 3526 823 1.502 1.80 3112 791 1.235 1.48 2612 759 0.967 1.16
1.2 4183 921 2.087 2.51
1 turn
2 turns
3 turns
4 turns
5 turns
6 turns
15-Ton Standard Drive
VP56 X BK105
6500
1 Turn
2 Turns
6000
SCFM
3 Turns
5500
4 Turns
5 Turns
5000
6 Turns
4500
0
0.2
0.4
0.6
0.8
1
1.2
1.4
External Static ("WC)
Unitary Products Group
41
127915-YIM-A-0405
TABLE 17: DR180 BLOWER PERFORMANCE - HIGH STATIC DRIVE (COOLING ONLY)
ESP
0.2
0.4
0.6
0.8
1.0
1.2
1.4
1.6
1.8
2.0
CFM
8032
7747
7490
7209
6905
6583
6252
5823
5427
4986
RPM KW
1168 6.346
1166 6.122
1170 5.841
1170 5.551
1171 5.247
1172 4.948
1175 4.658
1177 4.324
1179 4.066
1180 3.632
0 turns
BHP CFM RPM
KW
7.80 7765 1129 5.808
7.53 7479 1125 5.525
7.18 7161 1131 5.268
6.83 6841 1132 4.967
6.45 6531 1133 4.642
6.08 6203 1134 4.397
5.73 5836 1136 4.057
5.32 5457 1138 3.790
4.88 5032 1139 3.483
4.36 4520 1141 3.241
1 turn
15 Ton High Static Drive Blower Performance (Horizontal Discharge)
BHP
CFM RPM
KW BHP CFM RPM
KW BHP CFM RPM
KW
7.14 7396 1092 5.143 6.32 7225 1053 4.552 5.60 6936 1013 4.209
6.79 7095 1091 4.860 5.98 6907 1054 4.347 5.35 6610 1013 3.936
6.48 6792 1093 4.602 5.66 6578 1054 4.074 5.01 6243 1013 3.657
6.11 6508 1094 4.347 5.35 6292 1055 3.969 4.76 5875 1014 3.418
5.71 6223 1095 4.118 5.06 5952 1055 3.658 4.39 5535 1015 3.102
5.41 5866 1097 3.803 4.56 5585 1057 3.388 4.07 5091 1017 2.899
4.87 5502 1098 3.596 4.32 5166 1058 3.095 3.71 4617 1017 2.598
4.55 5075 1099 3.285 3.94 4670 1059 2.801 3.36
4.18 4585 1100 2.891 3.47
3.89
2 turns
3 turns
4 turns
BHP CFM RPM
5.18 6573
972
4.72 6270
973
4.39 5955
974
4.10 5575
974
3.72 5144
975
3.48 4686
976
3.12
KW
3.730
3.438
3.197
3.005
2.686
2.471
BHP
4.48
4.13
3.84
3.61
3.22
2.97
CFM RPM KW BHP
6271 933 3.307 3.97
5923 934 3.046 3.66
5512 933 2.869 3.44
5153 935 2.550 3.06
4689 936 2.392 2.87
5 turns
6 turns
Chart shading corresponds to minimum motor horsepower requirements as defined below.
7.5 HP motor
5 HP motor
15-ton High Static Drive
VP60 & BK90
8500
0 Turns
8000
SCFM
1 Turn
7500
2 Turns
3 Turns
7000
4 Turns
5 Turns
6500
6 Turns
6000
5500
5000
4500
0.0
0.2
0.4
0.6
0.8
1.0
1.2
1.4
1.6
1.8
2.0
External Static ("WC)
42
Unitary Products Group
127915-YIM-A-0405
TABLE 18: DR180 BLOWER PERFORMANCE - HIGH STATIC DRIVE (GAS HEAT)
ESP
0.2
0.4
0.6
0.8
1.0
1.2
1.4
1.6
1.8
2.0
CFM
7871
7592
7340
7065
6767
6451
6127
5707
5318
4886
RPM KW
1145 6.22
1143 6.00
1147 5.72
1147 5.44
1148 5.14
1149 4.85
1152 4.56
1153 4.24
1155 3.98
1156 3.56
0 turns
BHP CFM RPM
KW
7.65 7610 1106
5.69
7.38 7329 1103
5.41
7.04 7018 1108
5.16
6.69 6704 1109
4.87
6.32 6400 1110
4.55
5.96 6079 1111
4.31
5.61 5719 1113
3.98
5.21 5348 1115
3.71
4.78 4931 1116
3.41
4.27 4430 1118
3.18
1 turn
15 Ton High Static Drive Blower Performance (Horizontal Discharge)
BHP
CFM RPM
KW BHP CFM RPM
KW BHP CFM RPM
KW
7.00 7248 1070
5.04 6.20 7081 1032
4.46 5.49 6797
993
4.12
6.66 6953 1069
4.76 5.86 6769 1033
4.26 5.24 6478
993
3.86
6.35 6656 1071
4.51 5.55 6446 1033
3.99 4.79 6118
993
3.58
5.99 6398 1072
4.26 5.24 6175 1034
3.89 4.67 5758
994
3.35
5.59 6099 1073
4.04 4.84 5833 1034
3.58 4.30 5424
995
3.04
5.30 5749 1075
3.73 4.47 5473 1036
3.32 3.99 4989
997
2.84
4.77 5392 1076
3.52 4.23 5063 1037
3.03 3.64 4525
997
2.55
4.46 4974 1077
3.22 3.86 4577 1038
2.74 3.29
4.10 4493 1078
2.83 3.40
3.81
2 turns
3 turns
4 turns
BHP CFM RPM
5.07 6442
953
4.63 6095
954
4.30 5795
955
4.02 5464
955
3.65 5041
956
3.41 4592
956
3.06
KW
3.66
3.37
3.13
2.94
2.63
2.42
BHP
4.39
4.04
3.76
3.53
3.16
2.91
CFM RPM KW
6146 914 3.24
5805 915 2.99
5402 914 2.81
5050 916 2.50
4595 917 2.34
5 turns
BHP
3.89
3.58
3.37
3.00
2.81
6 turns
Chart shading corresponds to minimum motor horsepower requirements as defined below.
7.5 HP motor
5 HP motor
15-ton High Static Drive
VP60 & BK90
8000
0 Turns
1 Turn
7500
2 Turns
3 Turns
7000
SCFM
4 Turns
6500
5 Turns
6 Turns
6000
5500
5000
4500
0.0
0.2
0.4
0.6
0.8
1.0
1.2
1.4
1.6
1.8
2.0
External Static ("WC)
Unitary Products Group
43
127915-YIM-A-0405
TABLE 19: DR240 BLOWER PERFORMANCE - STANDARD DRIVE (COOLING ONLY)
DR240 Standard Drive Blower Performance (Horizontal Discharge)
RPM KW BHP CFM RPM KW BHP CFM RPM KW BHP CFM RPM KW BHP CFM RPM KW BHP CFM RPM
KW
1025 6.94 8.79 9021 993 6.211 7.87 8684 962 5.59 7.08 8422 929 5.057 6.41 8028 896 4.516 5.72 7677.5 863 4.00758
1027 6.629 8.40 8645 995 5.912 7.49 8282 963 5.3 6.72 8022 930 4.781 6.06 7605 897 4.259 5.40 7243 864 3.75462
1028 6.283 7.96 8262 996 5.606 7.10 7869 965
5
6.34 7585 931 4.482 5.68 7160 898 3.971 5.03 7182.8 864 3.47616
1028 5.979 7.58 7859 997 5.284 6.70 7434 965 4.67 5.92 7136 932 4.171 5.29 6684 899 3.671 4.65 6421.9 865 3.24768
1029 5.612 7.11 7410 998 4.924 6.24 6950 966 4.3 5.45 6643 933 3.836 4.86 6142 900 3.328 4.22 5834.4 866 2.92638
1030 5.238 6.64 6936 1000 4.556 5.77 6443 967 3.95 5.01 6104 934 3.496 4.43 5595 901 1.224 1.55 5217.3 867 2.59998
1033 4.835 6.13 6429 1001 4.179 5.30 5921 969 3.58 4.54 5406 936 3.098 3.93 4942 902 2.672 3.39 4488 868 2.26746
1034 4.443 5.63 5916 1002 3.79 4.80 5296 970 3.21 4.07 4691 938 2.699 3.42 4318 903 2.391 3.03
1036 4.024 5.10 5277 1004 3.402 4.31 4608 971 2.84 3.60
1038 3.605 4.57 4676 1005 3.066 3.89
1 Turn
2 Turns
3 Turns
4 Turns
5 Turns
6 Turns
Chart shading corresponds to minimum motor horsepower requirements as defined below.
7.5 HP motor
5 HP motor
ESP
0.2
0.4
0.6
0.8
1
1.2
1.4
1.6
1.8
2
CFM
9445
9172
8689
8363
7944
7498
6997
6421
5814
5234
9500
9000
BHP
5.08
4.76
4.41
4.12
3.71
3.29
2.87
20-Ton Standard Drive
1VP68 & 1BK110
1 Turn
2 Turns
3 Turns
8500
8000
4 Turns
5 Turns
CFM
6 Turns
7500
7000
6500
6000
5500
5000
0.2
0.4
0.6
0.8
1
1.2
1.4
1.6
1.8
2
External Static ("WC)
44
Unitary Products Group
127915-YIM-A-0405
TABLE 20: DR240 BLOWER PERFORMANCE - STANDARD DRIVE (GAS HEAT)
DR240 Standard Drive Blower Performance (Gas heat) (Horizontal Discharge)
RPM KW BHP CFM RPM KW BHP CFM RPM KW BHP CFM RPM KW BHP CFM RPM KW
1005 6.804 8.62 8844 974 6.089 7.72 8514 943 5.48 6.94 8257 911 4.958 6.28 7871 878 4.427
1007 6.499 8.24 8475 975 5.796 7.35 8120 944 5.199 6.59 7865 912 4.687 5.94 7456 879 4.175
1008 6.16 7.81 8100 976 5.496 6.96 7715 946 4.903 6.21 7436 913 4.394 5.57 7020 880 3.893
1008 5.862 7.43 7705 977 5.18 6.56 7288 946 4.581 5.81 6996 914 4.089 5.18 6553 881 3.599
1009 5.502 6.97 7265 978 4.827 6.12 6814 947 4.22 5.35 6513 915 3.761 4.77 6022 882 3.263
1010 5.135 6.51 6800 980 4.467 5.66 6317 948 3.876 4.91 5984 916 3.427 4.34 5485 883
1.2
1013 4.74 6.01 6303 981 4.097 5.19 5805 950 3.513 4.45 5300 918 3.037 3.85 4845 884 2.62
1014 4.356 5.52 5800 982 3.716 4.71 5192 951 3.15 3.99 4599 920 2.646 3.35 4233 885 2.344
1016 3.945 5.00 5174 984 3.335 4.23 4518 952 2.784 3.53
1018 3.534 4.48 4584 985 3.006 3.81
1 Turn
2 Turns
3 Turns
4 Turns
5 Turns
Chart shading corresponds to minimum motor horsepower requirements as defined below.
7.5 HP motor
5 HP motor
ESP
0.2
0.4
0.6
0.8
1
1.2
1.4
1.6
1.8
2
CFM
9260
8992
8519
8199
7788
7351
6860
6295
5700
5131
BHP
5.61
5.29
4.93
4.56
4.14
1.52
3.32
2.97
CFM
7527
7101
7042
6296
5720
5115
4400
RPM
846
847
847
848
849
850
851
KW
3.929
3.681
3.408
3.184
2.869
2.549
2.223
BHP
4.98
4.66
4.32
4.03
3.64
3.23
2.82
6 Turns
20-Ton Standard Drive (Gas Heat)
1VP68 & 1BK110
9500
1 Turn
9000
8500
2 Turns
3 Turns
4 Turns
CFM
8000
7500
5 Turns
6 Turns
7000
6500
6000
5500
5000
0.2
0.4
0.6
0.8
1
1.2
1.4
1.6
1.8
2
External Static ("WC)
Unitary Products Group
45
127915-YIM-A-0405
TABLE 21: DR240 BLOWER PERFORMANCE - HIGH STATIC DRIVE (COOLING ONLY)
DR240 Blower Performance (Horizontal Discharge) (High Static Option)
RPM KW BHP CFM RPM KW BHP CFM RPM KW BHP CFM RPM KW BHP CFM
1118 9.15 11.64 10161 1086 8.42 10.70 9949 1056 7.76 9.86 9634 1025 7.05 8.96 9232
1119 8.82 11.21 9792 1088 8.06 10.24 9589 1057 7.41 9.42 9231 1025 6.75 8.58 8849
1121 8.58 10.91 9427 1089 7.70 9.79 9209 1058 7.08 9.00 8852 1026 6.43 8.18 8570
1122 8.14 10.35 9059 1090 7.35 9.34 8813 1059 6.73 8.55 8467 1027 6.11 7.76 8145
1123 7.77 9.88 8669 1091 6.97 8.87 8395 1060 6.34 8.06 8051 1028 5.75 7.31 7693
1124 7.37 9.37 8397 1094 6.67 8.48 7952 1061 5.95 7.56 7611 1029 5.38 6.84 7210
1126 6.97 8.86 7948 1094 6.24 7.94 7481 1063 5.54 7.04 7132 1029 4.99 6.35 6692
1127 6.54 8.32 7481 1095 5.84 7.42 7024 1063 5.16 6.56 6615 1031 4.60 5.85 5870
1128 6.13 7.79 6927 1097 5.43 6.90 6550 1064 4.84 6.15 6036 1032 4.20 5.34 5518
1130 5.71 7.26 6324 1098 5.10 6.48 5925 1066 4.39 5.59 5458 1033 3.79 4.82 4852
1131 5.30 6.74 5763 1099 4.39 5.58 5560 1066 4.14 5.26 4909 1034 3.47 4.42
1133 4.69 5.96 5247 1100 4.14 5.27 5195 1067 3.89 4.94
1134 4.45 5.66
1 Turn
2 Turns
3 Turns
4 Turns
Chart shading corresponds to minimum horsepower requirements as defined below.
10 HP motor
7.5 HP motor
5 HP motor
ESP
0.2
0.4
0.6
0.8
1
1.2
1.4
1.6
1.8
2
2.2
2.4
2.6
CFM
10477
10144
9826
9473
9032
8654
8262
7815
7372
6909
6324
5814
5302
RPM
973
974
993
993
995
996
997
997
998
1000
KW
6.43
6.13
5.90
5.55
5.19
4.82
4.45
4.06
3.67
3.30
BHP
8.18
7.79
7.50
7.06
6.60
6.13
5.66
5.16
4.67
4.20
CFM
8880
8473
8101
7609
7112
6616
6122
5478
4811
5 Turns
RPM
956
951
955
962
961
962
965
967
966
KW BHP
5.74 7.30
5.45 6.92
5.18 6.58
4.80 6.10
4.44 5.64
4.10 5.21
3.77 4.80
3.37 4.28
3.01 3.83
6 Turns
20-Ton High Static Drive
1VP71 & 1BK110 (10HP Motor)
11000
1 Turn
2 Turns
10000
3 Turns
4 Turns
9000
5 Turns
CFM
6 Turns
8000
7000
6000
5000
0.2
0.4
0.6
0.8
1
1.2
1.4
1.6
1.8
2
2.2
2.4
2.6
External Static ("WC)
46
Unitary Products Group
127915-YIM-A-0405
TABLE 22: DR240 BLOWER PERFORMANCE - HIGH STATIC DRIVE (GAS HEAT)
DR240 Blower Performance (Gas Heat) (Horizontal Discharge) (High Static Option)
RPM KW BHP CFM RPM KW BHP CFM RPM KW BHP CFM RPM KW BHP CFM RPM KW
1096 8.98 11.4 9962 1065 8.25 10.5 9754 1035 7.61 9.67 9445 1005 6.91 8.79 9051 954 6.31
1097 8.65
11 9600 1067 7.9
10 9401 1036 7.27 9.24 9050 1005 6.62 8.41 8675 955 6.01
1099 8.41 10.7 9242 1068 7.55
9.6 9028 1037 6.94 8.82 8678 1006 6.31 8.02 8402 974 5.78
1100 7.98 10.1 8881 1069 7.21 9.16 8640 1038 6.59 8.38 8301 1007 5.99 7.61 7985 974 5.45
1101 7.62 9.68 8499 1070 6.84 8.69 8230 1039 6.22
7.9 7893 1008 5.64 7.16 7542 975 5.09
1102 7.23 9.19 8232 1073 6.54 8.31 7796 1040 5.83 7.41 7462 1009 5.27
6.7 7069 976 4.73
1104 6.84 8.69 7792 1073 6.12 7.78 7334 1042 5.43
6.9 6992 1009 4.9 6.23 6561 977 4.36
1105 6.41 8.15 7334 1074 5.73 7.28 6886 1042 5.06 6.44 6485 1011 4.51 5.74 5755 977 3.98
1106 6.01 7.63 6791 1075 5.32 6.77 6422 1043 4.74 6.03 5918 1012 4.12 5.24 5410 978 3.6
1108 5.6 7.12 6200 1076 5
6.36 5809 1045 4.31 5.48 5351 1013 3.72 4.73 4757 980 3.24
1109 5.2 6.61 5650 1077 4.3 5.47 5451 1045 4.06 5.16 4813 1014 3.41 4.33
1111 4.6 5.85 5144 1078 4.06 5.17 5093 1046 3.81 4.85
1112 4.37 5.55
1 Turn
2 Turns
3 Turns
4 Turns
5 Turns
Chart shading corresponds to minimum horsepower requirements as defined below.
10 HP motor
7.5 HP motor
5 HP motor
ESP
0.2
0.4
0.6
0.8
1
1.2
1.4
1.6
1.8
2
2.2
2.4
2.6
CFM
10272
9945
9633
9287
8855
8484
8100
7662
7227
6774
6200
5700
5198
BHP
8.02
7.64
7.35
6.92
6.47
6.01
5.55
5.06
4.57
4.11
CFM
8706
8307
7942
7460
6973
6486
6002
5371
4717
RPM
937
932
936
943
942
943
946
948
947
KW BHP
5.63 7.16
5.34 6.79
5.07 6.45
4.71 5.98
4.35 5.53
4.02 5.11
3.7
4.7
3.3
4.2
2.95 3.76
6 Turns
20-Ton High Static Drive (Gas Heat)
1VP71 & 1BK110
11000
1 Turn
10000 2 Turns
3 Turns
CFM
4 Turns
9000 5 Turns
6 Turns
8000
7000
6000
5000
0.2
0.4
0.6
0.8
1
1.2
1.4
1.6
1.8
2
2.2
2.4
2.6
External Static ("WC)
Unitary Products Group
47
127915-YIM-A-0405
TABLE 23: DR300 BLOWER PERFORMANCE - STANDARD DRIVE
DR300 Blower Performace (Horizontal Discharge)
RPM KW BHP CFM RPM KW BHP CFM RPM KW BHP CFM RPM KW BHP
996 7.1 9.04 8800 959 6.1 7.79 8700 950 5.9 7.53 8250 913 4.95 6.97
997 6.6 8.43 8150 960 5.6 7.15 8010 950 5.4 6.89 7540 915 4.57 6.44
998 6.1 7.79 7510 961 5.1 6.51 7330 952 4.9 6.25 6820 916 4.09 5.77
1000 5.6 7.15 6830 962 4.6 5.87 6570 953 4.4 5.62 5990 916 3.52 4.96
1000 5.1 6.51 6140 964 4.2 5.36 5850 954 3.8 4.86 5210 918 3.05 4.29
1001 4.6 5.87 5480 965 3.6 4.6
1003 3.9 4.97
1 Turn
2 Turns
3 Turns
4 Turns
Chart shading corresponds to minimum motor horsepower requirements as defined below.
10 HP motor
7.5 HP motor
5 HP motor
ESP
0.4
0.6
0.8
1
1.2
1.4
1.6
CFM
9550
9010
8430
7830
7210
6500
5460
9000
CFM
8500
8000
RPM
877
879
880
881
KW
4.7
4.2
3.7
3.1
BHP
5.99
5.33
4.76
3.99
CFM
7250
6460
5600
RPM
842
843
844
KW
3.9
3.5
3.1
BHP
4.97
4.47
3.99
6 Turns
5 Turns
25-Ton Standard Drive
1VP60 & 1B5V94
10000
9500
CFM
8050
7290
6480
5500
1 Turn
2 Turns
3 Turns
4 Turns
5 Turns
7500
6 Turns
7000
6500
6000
5500
0.4
0.6
0.8
1
1.2
1.4
External Static ("WC)
48
Unitary Products Group
127915-YIM-A-0405
TABLE 24: DR300 BLOWER PERFORMANCE - HIGH STATIC DRIVE
DR300 Blower Performance (Horizontal Discharge)
RPM KW BHP CFM RPM KW BHP CFM RPM KW BHP CFM RPM KW BHP
1200 12.5 16.0 11175 1164 11.5 14.7 10620 1127 10.4 13.3 10500 1092 9.2 11.7
1201 11.8 15.1 10600 1166 10.8 13.8 10100 1131 9.7 12.4 9980 1095 8.6 11.0
1203 11.1 14.2 10100 1169 10.2 13.0 9520 1132 9.1 11.6 9360 1097 8 10.2
1205 10.4 13.3 9430 1171 9.5 12.1 8870 1134 8.4 10.7 8800 1099 7.4 9.4
1207 9.9 12.6 9270 1173 8.9 11.4 8590 1136 7.9 10.1 8120 1101 6.8 8.7
1210 9.2 11.7 8480 1174 7.9 10.1 8070 1039 7.1 9.1 7340 1103 6.1 7.8
1213 8.4 10.7 7750 1177 7.2 9.2 7560 1140 6.5 8.3 7220 1103 5.9 7.5
1215 7.7 9.8 7600 1178 7
8.9 6600 1142 5.6 7.1 5810 1106 4.7 6.0
1216 7
8.9 6300 1180 6.1 7.8 5450 1145 4.9 6.3
1218 6.2 7.9 5230 1184 5.1 6.5
1221 5.4 6.9
1 Turn
2 Turns
3 Turns
4 Turns
Chart shading corresponds to minimum horsepower requirements as defined below.
15 HP motor
10 HP motor
7.5 HP motor
ESP
0.4
0.6
0.8
1
1.2
1.4
1.6
1.8
2
2.2
2.4
CFM
11600
11060
10500
9930
9800
9200
8400
7830
7300
6400
5400
CFM
9875
9320
8600
8240
7240
6820
5380
RPM
1058
1060
1061
1063
1065
1066
1069
KW BHP CFM RPM KW BHP
8.2 10.5 9100 1020 7.4 9.4
7.6 9.7 8920 1022 6.9 8.8
6.9 8.8 8230 1024 6.3 8.0
6.4 8.2 7500 1025 5.7 7.3
5.7 7.3 6990 1027 5.2 6.6
5.3 6.8 6100 1029 4.8 6.1
4.2 5.4
5 Turns
6 Turns
25-Ton High Static Drive
1VP71 & 1B5V94
11500 1 Turn
2 Turns
10500 3 Turns
4 Turns
5 Turns
CFM
9500
6 Turns
8500
7500
6500
5500
0.4
0.6
0.8
1
1.2
1.4
1.6
1.8
2
2.2
2.4
External Static ("WC)
Unitary Products Group
49
127915-YIM-A-0405
TABLE 25: STATIC RESISTANCES1
RESISTANCE, IWG
CFM
DESCRIPTION
15 TON
20 TON
25 TON
4500
5600
7500
6000
8000
9400
7500
10000
12500
0.1
0.1
0.1
0.1
0.1
0.1
0.11
0.11
0.11
18 KW
0.3
0.35
0.3
0.35
0.40
0.45
0.31
0.45
0.55
36 KW
0.32
0.4
0.37
0.4
0.48
0.5
0.38
0.5
0.6
54 KW
0.38
0.45
0.49
0.45
0.52
0.57
0.5
0.6
0.7
72 KW
0.38
0.45
0.49
0.45
0.52
0.57
0.5
0.6
0.7
ECONOMIZER OPTION
0.1
0.1
0.1
0.1
0.1
0.1
0.06
0.11
0.18
VERTICAL DUCT CONNECTIONS2
0.1
0.2
0.3
0.2
0.3
0.5
0.36
0.32
0.46
WET INDOOR COIL
ELECTRIC HEAT OPTIONS
1.
Deduct these resistance values from the available external static pressures shown in the respective Blower Performance Table (See Note 2 for
exception.)
Since the resistance to air flow will be more for vertical duct connections than for side duct connections, deduct these pressures from the ESP values
on the respective unit’s blower performance table.
2.
TABLE 26: POWER EXHAUST PERFORMANCE
STATIC RESISTANCE OF RETURN DUCTWORK, IWG
MOTOR
SPEED
0.2
0.3
0.4
0.5
0.6
CFM
KW
CFM
KW
CFM
KW
CFM
KW
CFM
KW
0.99
HIGH*
5250
0.83
4500
0.85
4200
0.88
3750
0.93
3000
MEDIUM
4900
0.77
3900
0.79
3500
0.82
2900
0.85
-
-
LOW
4400
0.72
3700
0.74
3000
0.78
-
-
-
-
* Factory Setting
Power Exhaust motor is a 3/4 HP, PSC type with sleeve bearings, a 48 frame and inherent protection.
TABLE 27: BLOWER MOTOR AND DRIVE DATA
MODEL
SIZE
DRIVE
MOTOR1
BLOWER
RANGE
(RPM) HP FRAME EFF.
(%)
Standard 760/940
15 TON
High
Speed
Access
5
875/1150 7.5
High
Speed
Access
Low
Speed
Drive
950/1120 10
842/1003
High
15
Speed 1020/1221
Access
1.
2.
50
OUTSIDE
DIA.
(IN.)
PITCH
DIA.
(IN.)
BORE DESIG(IN.) NATION
OUTSIDE PITCH
DIA.
DIA.
(IN.)
(IN.)
89.5
1VP56
5.35
4.3-5.32
1-1/8
BK105
10.5
9.9
213 T
91.7
1VP60
6.0
4.2-5.5
1-3/8
BK90
8.75
8.4
1VP68
6.75
5.5-6.52
213 T
89
1VP71
7.1
5.4-6.6
1-3/8
BK110
10.75
10.4
1VP60
6.0
4.2-5.5
7.5
25 TON Standard
DESIGNATION
89
1-3/8
254 T
1VP71
7.1
5.5-6.5
1-5/8
PITCH
BORE DESIGLENGTH QTY.
(IN.) NATION
(IN.)
1
BX81
82.8
1
1-3/16
BX81
82.8
1
BX78
79.8
1-3/16
1B5V94
91
BELT
(NOTCHED)
FIXED BLOWER PULLEY
184 T
Standard 850/1010 7.5
20 TON
ADJUSTABLE MOTOR PULLEY
9.7
9.5
1
1-7/16
BX81
82.8
All motors have a nominal speed of 1800 RPM, a 1.15 service factor and a solid base. They can operate to the limit of their service factor because
they are located in the moving air, upstream of any heating device.
Do NOT close this pulley below 1 turn open.
Unitary Products Group
127915-YIM-A-0405
DR180 Charging Chart
Outdoor Temp (ºF)
Discharge Pressure (psi)
350
330
115º
310
290
105º
270
250
95º
230
85º
210
75º
65º
190
170
150
60
65
70
75
80
85
90
Suction Pressure (psi)
1. Make sure that both condenser fans are running when charging. One fan may switch off at lower ambient
temperatures making the chart above inaccurate.
2. This chart is applicable to unit with the TXV's left to the factory setting. If the TXV's have been adjusted in the field,
The charging chart may no longer apply.
FIGURE 14 - CHARGING CHART - 15 TON
DR240 Charging Chart
Outdoor Temp (ºF)
Discharge Pressure (psi)
350
115º
330
310
105º
290
270
95º
250
230
85º
210
75º
190
65º
170
150
60
65
70
75
80
85
90
Suction Pressure (psi)
Both fans must be running when charging the unit. One fan may switch off at low ambient temperatures making this chart inaccurate.
FIGURE 15 - CHARGING CHART - 20 TON
Unitary Products Group
51
127915-YIM-A-0405
DR300 Charging Chart
Outdoor Temp (ºF)
350
115º
Discharge Pressure (psi)
330
310
105º
290
95º
270
250
85º
230
75º
210
65º
190
170
150
55
60
65
70
75
80
85
Suction Pressure (psi)
Both fans must be running when charging the unit. One fan may switch off at low ambient temperatures making this chart inaccurate.
FIGURE 16 - CHARGING CHART - 25 TON
PHASING
2. Pulleys can be adjusted in half turn increments.
Check for proper compressor rotation. If the blower or
compressors rotate in the wrong direction at start-up,
the electrical connection to the unit is misphased.
Change the incoming line connection phasing to obtain
proper rotation. (Scroll compressors operate in only
one direction. If the scroll is drawing low amperage,
has similar suction and discharge pressures, or producing a high noise level, the scroll is misphased).
3. The tension on the belt should be adjusted as
shown in the Belt Adjustment Figure 17.
Scroll compressors require proper rotation to
operate correctly. Do not change the internal
wiring to make the blower, condenser fans, or
compressor rotate correctly. Change the
incoming power to the main terminal block to
obtain proper rotation.
CHECKING SUPPLY AIR CFM
The RPM of the supply air blower will depend on the
required CFM, the unit accessories or options and the
static resistances of both the supply and the return air
duct systems. With this information, the RPM for the
supply air blower and the motor pulley adjustment
(turns open) can be determined from the Blower Performance Data Tables.
Note the following:
PROCEDURE FOR ADJUSTING BELT TENSION:
1. Loosen nuts (A) (top and bottom).
2. Adjust the tension by turning bolt (B).
3. Never loosen nuts (C) from each other.
4. Use a belt tension checker to apply a perpendicular force to be one belt at the
midpoint of the span as shown. The deflection force should be applied
until a specific deflection distance of 4mm (5/32") is obtained. To determine
the deflection distance from normal position, use a straight edge from
sheave to sheave as a reference line. The recommended deflection force
is as follows:
SPAN LENGTH
DEFL FORCE
(B)
*Never Loosen
(A)
(C)*
Tension new belts at the max. deflection force recommended for the belt
section. Check the belt tension at least two times during the first 24 hours of
operation. Any re-tensioning should fall between the min. and max.
deflection force values.
5. After adjusting, re-tighten nuts (A).
FIGURE 17 - BELT ADJUSTMENT
1. The supply air CFM must be within the limitations
shown in the Unit Application Data Table 1.
52
Unitary Products Group
127915-YIM-A-0405
Start the supply air blower motor. Adjust the resistances in both the supply and the return air duct systems to balance the air distribution throughout the
conditioned space. The job specifications may require
that this balancing be done by someone other than the
equipment installer.
To check the supply air CFM after the initial balancing
has been completed:
1. Remove the two 5/16" dot plugs from the blower
motor and the filter access panels shown in the
Dimensions and Clearances Figure 12.
2. Insert at least 8" of 1/4 inch tubing into each of
these holes for sufficient penetration into the air
flow on both sides of the indoor coil.
NOTE: The tubes must be inserted and held in a position perpendicular to the air flow so that velocity pressure will not affect the static pressure
readings.
3. Using an inclined manometer, determine the pressure drop across a dry evaporator coil. Since the
moisture on an evaporator coil may vary greatly,
measuring the pressure drop across a wet coil
under field conditions would be inaccurate. To
assure a dry coil, the compressors should be deactivated while the test is being run.
NOTE: DE-ENERGIZE THE COMPRESSORS BEFORE TAKING ANY TEST MEASUREMENTS
TO ASSURE A DRY INDOOR COIL.
OPERATION
SEQUENCE OF OPERATIONS OVERVIEW
For these units, the thermostat makes a circuit
between "R" and "Y1" for the first stage of cooling.
The call is passed to the unit control board (UCB),
which then determines whether the requested operation is available and, if so, which components to energize.
PRESSURE DROP ACROSS A DRY COIL VS SUPPLY AIR CFM
DR180
For electric heat units, the UCB passes the call to the
electric heater.
0.55
PRESSURE DROP (IWG)
After readings have been obtained, remove the tubes
and reinstall the two 5/16" dot plugs that were removed
in Step 1.
For gas heating, the UCB monitors the "W1" call but
does not handle the operation of the gas furnace. An
ignition control board controls the gas heater operation.
0.65
In both cases, when the "W1" call is sensed, the indoor
air blower is energized following a specified heating
delay.
0.45
DR300
0.35
If at any time a call for both heating and cooling are
present, the heating operation will be performed. If
operating, the cooling system is halted as with a completion of a call for cooling. Heating always takes priority.
DR240
0.25
0.15
0.05
4000
Failure to properly adjust the total system air
quantity and static pressure can result in
extensive system damage.
5000
6000
7000
8000
9000
10000
11000
12000
NOMINAL AIR FLOW (CFM)
FIGURE 18 - PRESSURE DROP ACROSS A DRY
INDOOR COIL VS SUPPLY AIR CFM
FOR ALL UNIT TONNAGES
4. Knowing the pressure drop across a dry coil, the
actual CFM through the unit can be determined
from the curve in Pressure Drop vs. Supply Air
CFM Figure 18.
Unitary Products Group
COOLING SEQUENCE OF OPERATION
CONTINUOUS BLOWER
By setting the room thermostat fan switch to "ON," the
supply air blower will operate continuously.
53
127915-YIM-A-0405
INTERMITTENT BLOWER
With the room thermostat fan switch set to "AUTO" and
the system switch set to either the "AUTO" or "HEAT"
settings, the blower is energized whenever a cooling or
heating operation is requested. The blower is energized after any specified delay associated with the
operation.
When energized, the indoor blower has a minimum run
time of 30 seconds. Additionally, the indoor blower has
a delay of 10 seconds between operations.
NO OUTDOOR AIR OPTIONS
When the thermostat calls for the first stage of cooling,
the low-voltage control circuit from "R" to "Y1" and "G"
is completed. For first stage cooling, compressor #1,
condenser fan motor #1, and condenser fan motor #2
(if the ambient temperature is above 60°F), is energized. After completing the specified fan on delay for
cooling, the UCB will energize the blower motor.
When the thermostat calls for the second stage of cooling, the low-voltage control circuit from "R" to "Y2" is
completed. Compressor #2, condenser fan motor #3,
and condenser fan motor #4 (if the ambient temperature is above 60°F), is energized, provided it has not
been locked-out.
If there is an initial call for both stages of cooling, the
UCB will delay energizing compressor #2 by 30 seconds in order to avoid a higher than normal current in
rush.
motor (if the fan switch on the room thermostat is set in
the "AUTO" position) and drives the economizer dampers from fully closed to their minimum position. If the
enthalpy of the outdoor air is below the setpoint of the
enthalpy controller (previously determined), "Y1" energizes the economizer. The dampers will modulate to
maintain a constant supply air temperature as monitored by the discharge air sensor. If the outdoor air
enthalpy is above the setpoint, "Y1" energizes compressor #1, condenser fan motor #1, and condenser
fan motor #2 (if the ambient temperature is above
60°F).
When the thermostat calls for "second-stage" cooling,
the low voltage control circuit from "R" to "Y2" is completed. The UCB energizes the first available compressor If the enthalpy of the outdoor air is below the
setpoint of the enthalpy controller (i.e. first stage has
energized the economizer), "Y2" will energize compressor #1. If the outdoor air is above the setpoint, "Y2"
will energize compressor #2.
Once the thermostat has been satisfied, it will de-energize Y1 and Y2. If the compressors have satisfied their
minimum run times, the compressors and condenser
fans are de-energized. Otherwise, the unit operates
each cooling system until the minimum run times for
the compressors have been completed. Upon the final
compressor de-energizing, the blower is stopped following the elapse of the fan off delay for cooling, and
the economizer damper goes to the closed position. If
the unit is in continues fan operation the economizer
damper goes to the minimum position.
ECONOMIZER WITH DUAL ENTHALPY SENSORS -
Once the thermostat has been satisfied, it will de-energize Y1 and Y2. If the compressors have satisfied their
minimum run times, the compressors and condenser
fans are de-energized. Otherwise, the unit operates
each cooling system until the minimum run times for
the compressors have been completed. Upon the final
compressor de-energizing, the blower is stopped following the elapse of the fan off delay for cooling.
To be available, a compressor must not be locked-out
due to a high or low-pressure switch or freezestat trip
and the anti-short cycle delay (ASCD) must have
elapsed.
ECONOMIZER WITH SINGLE ENTHALPY SENSOR -
When the room thermostat calls for "first-stage" cooling, the low voltage control circuit from "R" to "G" and
"Y1" is completed. The UCB energizes the blower
54
The operation with the dual enthalpy sensors is identical to the single sensor except that a second enthalpy
sensor is mounted in the return air. This return air sensor allows the economizer to choose between outdoor
air and return air, whichever has the lowest enthalpy
value, to provide maximum operating efficiency.
ECONOMIZER (SINGLE OR DUAL) WITH POWER
EXHAUST -
This system operates as specified above with one
addition. The power exhaust motor is energized 45
seconds after the actuator position exceeds the
exhaust fan setpoint on the economizer control. When
the power exhaust is operating, the second stage of
mechanical cooling will not operate. As always, the "R"
to "G" connection provides minimum position but does
not provide power exhaust operation.
Unitary Products Group
127915-YIM-A-0405
MOTORIZED OUTDOOR AIR DAMPERS -
This system operation is the same as the units with no
outdoor air options with one exception. When the "R" to
"G" circuit is complete, the motorized damper drives
open to a position set by the thumbwheel on the
damper motor. When the "R" to "G" circuit is opened,
the damper spring returns fully closed.
COOLING OPERATION ERRORS
Each cooling system is monitored for operation outside
of the intended parameters. Errors are handled as
described below. All system errors override minimum
run times for compressors.
HIGH-PRESSURE LIMIT SWITCH
During cooling operation, if a high-pressure limit switch
opens, the UCB will de-energize the associated compressor, initiate the ASCD (Anti-short cycle delay), and,
if the other compressor is idle, stop the condenser
fans. If the call for cooling is still present at the conclusion of the ASCD, the UCB will re-energize the halted
compressor.
Should a high-pressure switch open three times within
two hours of operation, the UCB will lock-out the associated compressor and flash a code (see Table 33). If
the other compressor is inactive, the condenser fans
will be de-energized.
LOW-PRESSURE LIMIT SWITCH
The low-pressure limit switch is not monitored during
the initial 30 seconds of a cooling system's operation.
For the following 30 seconds, the UCB will monitor the
low-pressure switch to ensure it closes. If the low-pressure switch fails to close after the 30-second monitoring phase, the UCB will de-energize the associated
compressor, initiate the ASCD, and, if the other compressor is idle, stop the condenser fans.
Once the low-pressure switch has been proven (closed
during the 30-second monitor period described above),
the UCB will monitor the low-pressure limit switch for
any openings. If the low-pressure switch opens for
greater than 5 seconds, the UCB will de-energize the
associated compressor, initiate the ASCD, and, if the
other compressor is idle, stop the condenser fans.
If the call for cooling is still present at the conclusion of
the ASCD, the UCB will re-energize the halted compressor.
Unitary Products Group
Should a low-pressure switch open three times within
one hour of operation, the UCB will lock-out the associated compressor and flash a code (Table 33). If the
other compressor is inactive, the condenser fans will
be de-energized.
FREEZESTAT
During cooling operation, if a freezestat opens, the
UCB will de-energize the associated compressor, initiate the ASCD, and, if the other compressor is idle,
stop the condenser fans. If the call for cooling is still
present at the conclusion of the ASCD, the UCB will reenergize the halted compressor.
Should a freezestat open three times within two hours
of operation, the UCB will lock-out the associated compressor and flash a code (Table 33). If the other compressor is inactive, the condenser fans will be deenergized.
LOW AMBIENT COOLING
To determine when to operate in low ambient mode,
the UCB has a pair of terminals connected to a temperature-activated switch set at 30ºF. When the low ambient switch is closed and the thermostat is calling for
cooling, the UCB will operate in the low ambient mode.
Low ambient mode operates the compressors in this
manner: 10 minutes on, 5 minutes off. The indoor
blower is operated throughout the cycle. The 5-minute
off period is necessary to defrost the indoor coil.
Low ambient mode always begins with compressor
operation. Compressor minimum run time may extend
the minutes of compressor operation. The defrost cycle
will begin immediately following the elapse of the minimum run time.
When operating in low ambient mode, the UCB will not
lockout the compressors due to a freezestat trip. However, a freezestat trip will de-energize the associated
compressor. If the call for cooling is still present at the
end of the ASCD and the freezestat has closed, the
unit will resume operation.
SAFETY CONTROLS
The unit control board monitors the following inputs for
each cooling system:
1. A suction line freezestat to protect against low
evaporator temperatures due to a low airflow or a
55
127915-YIM-A-0405
low return air temperature, (opens at 26 ± 5 °F and
resets at 38 ± 5°F).
2. A high-pressure switch to protect against excessive discharge pressures due to a blocked condenser coil or a condenser motor failure, (opens at
405 ± 7 psig and resets at 265 ± 20 psig).
3. A low-pressure switch to protect against loss of
refrigerant charge, (opens at 22 ± 5 psig and resets
at 45 ± 5 psig).
The above pressure switches are hard-soldered to the
unit. The refrigeration systems are independently monitored and controlled. On any fault, only the associated
system will be affected by any safety/preventive action.
The other refrigerant system will continue in operation
unless it is affected by the fault as well.
The unit control board monitors the temperature limit
switch of electric heat units and the temperature limit
switch and the gas valve of gas furnace units.
on the board. (See Figure 19.) Each mode is described
below. Refer to Figures 19 - 21 when reading this section.
“NORMAL” MODE
When the reheat control board (RCB) detects a need
for dehumidification (24VAC) at "HUM" via the field
supplied dehumidistat connected to RHTB-1 and
RHTB-2 and there is not a call for cooling, it energizes
the hot gas relay (HGR), which energizes the 3-way
valve (SOL 3), the condenser coil valve (SOL 2), and
de-energizes the reheat coil bleed valve (SOL 1). The
Y1 signal is passed to the unit control board (UCB),
which engages circuit # 1, resulting in circuit #1 reheat
mode operation.
When the room thermostat calls for first stage cooling,
with or without a call for dehumidification, the RCB
senses a signal through "Y1", de-energizing the HGR,
which de-energizes SOL 3 and SOL 2, and energizes
SOL 1, engaging circuit # 1, resulting in circuit #1 cooling mode operation.
COMPRESSOR PROTECTION
The compressors also have inherent (internal) protection. If there is an abnormal temperature rise in a compressor, the protector will open to shut down the
compressor. The UCB incorporates features to minimize compressor wear and damage. An anti-short
cycle delay (ASCD) is utilized to prevent operation of a
compressor too soon after its previous run. Additionally, a minimum run time is imposed any time a compressor is energized.
When the room thermostat calls for second stage cooling, the RCB senses a signal through "Y1" & "Y2" and
engages circuit #1 and circuit #2 in the cooling mode.
Indoor blower operation is initiated upon a call for first
stage cooling, second stage cooling or dehumidification.
Anytime there is a call for 2 stages of cooling, the unit
will not operate in the reheat mode, even if there is a
call for dehumidification at "HUM".
The ASCD is initiated on unit start-up and on any compressor reset or lock-out.
The unit will not operate in the reheat mode if there is
any call for heating.
FLASH CODES
On units with economizers, the unit will not operate in
the reheat mode if there is a call for cooling and the
economizer is operating as first stage of cooling.
The UCB will initiate a flash code associated with
errors within the system. Refer to UNIT CONTROL
BOARD FLASH CODES Table 33.
RESET
Remove the call for cooling, by raising thermostat setting higher than the conditioned space temperature.
This resets any pressure or freezestat flash codes.
REHEAT MODE SEQUENCE OF OPERATION
The reheat control board allows the user to select two
different modes of operation via a jumper connection
56
All safety devices function as previously described.
"ALTERNATE” MODE
When the RCB detects a need for dehumidification
(24VAC) at "HUM" via the field supplied dehumidistat
connected to RHTB-1 and RHTB-2, and there is not a
call for cooling, it energizes the HGR, which energizes
the SOL 3, SOL 2, and de-energizes SOL 1. The unit
then operates with circuit #1 in reheat mode and circuit
#2 in cooling mode.
Unitary Products Group
127915-YIM-A-0405
When the room thermostat calls for first stage cooling
while there is still a call for dehumidification, no operational change is made. The call for cooling is ignored
and the unit continues to operate with circuit #1 in
reheat mode and circuit #2 in cooling mode.
When the room thermostat calls for second stage cooling, the RCB senses a signal through "Y1" & "Y2" and
de-energizes the HGR, which de-energizes SOL 3 and
SOL 2, and energizes SOL 1. Both circuits operate in
the cooling mode.
Indoor blower operation is initiated upon a call for first
stage cooling, second stage cooling or dehumidification.
Anytime there is a call for 2 stages of cooling, the unit
will not operate in the reheat mode, even if there is still
a call for dehumidification at "HUM".
The unit will not operate in the reheat mode if there is
any call for heating.
All safety devices function as previously described.
R
Y1
P4
Y2
K1
G
W1
K2
W2
OCC
K4
C
K3
COM
`
P6
P5
P3
HGRR
HGR
MODE
SELECTION
JUMPER
HUM
DEHUMIDISTAT
HARNESS
CONNECTION
FIGURE 19 - REHEAT CONTROL BOARD
Unitary Products Group
57
127915-YIM-A-0405
UCB
RHB
UNIT CONTROL
BOARD
REHEAT CONTROL
BOARD
HUM
HUMIDIFY
TERMINAL
RHR
REHEAT
RELAY
RHTB
REHEAT
TERMINAL
BLOCK
FIGURE 20 - REHEAT CONTROLS - PART 1
REHEAT
SOLENOID 1
REHEAT
SOLENOID 3
REHEAT
SOLENOID 2
UCB
UNIT CONTROL
BOARD
RHB
REHEAT
CONTROL
BOARD
FIGURE 21 - REHEAT CONTROLS - PART 2
58
Unitary Products Group
127915-YIM-A-0405
Check
Valve
Piping T
TXV
HPS
Condenser
Fan
Check
Valve
Air Flow
Air Flow
Condenser
Coil
Indoor Blower
FS
Air Flow
Evaporator
Coil
Hot Gas
Coil
Open in
Cooling
Refrigerant flow in cooling mode
Refrigerant flow in reheat mode
Bleed
Line to clear
Suction
line
the Hot Gas Coil
bleed
when it is not in use
HPS
LPS
Sol 1
Piping T
Accumulator
Sol 2
C1
Hot Gas Re-Heat
Solenoid Valve
(Sol 3)
Compressor
Open in
Reheat
FIGURE 22 - SYSTEM PIPING SCHEMATIC
ELECTRIC HEATING SEQUENCE OF OPERATIONS
The following sequence describes the operation of the
electric heat section.
Two-stage heating (applies to all heaters except 18
KW):
a.
Single-stage heating (applies only to 18 KW heater, all
other heaters MUST use a two-stage thermostat):
a.
Upon a call for heat by the thermostat, the heater
contactor (6M) will be energized. After completing
the specified fan on delay for heating, the UCB will
energize the blower motor.
b.
The thermostat will cycle the electric heat to satisfy
the heating requirements of the conditioned space.
If the second stage of heat is required, heater contactor (7M) will be energized. Note that on the 54
KW, 240V heater, heater contactors (7M & 8M) will
be energized and on the 72 KW, 240V heater,
heater contactors (8M & 9M) will be energized. After
completing the specified fan on delay for heating,
the UCB will energize the blower motor.
b.
Unitary Products Group
Upon a call for first-stage heat by the thermostat, the
heater contactor (6M) (6M & 7M on 72 KW, 240V)
will be energized. After completing the specified fan
on delay for heating, the UCB will energize the
blower motor.
The thermostat will cycle the electric heat to satisfy
the heating requirements of the conditioned space.
59
127915-YIM-A-0405
NOTE: All 240 & 480V heaters are provided with manual reset backup protection limits. These will
de-energize the heaters should the primary
limit fail to open or the contactors fail to open in
a failure mode.
HEATING OPERATION ERRORS
TABLE 28: LIMIT CONTROL SETTING
UNIT
(Tons)
VOLTAGE
15
20, 25
If the temperature limit opens three times within one
hour, it will lock-on the indoor blower motor and a flash
code is initiated (See Table 33).
SAFETY CONTROLS
15, 20,
25
TEMPERATURE
LIMIT SWITCH 3,
4, 5, 6 OPENS, ºF
18
120
170
36
120
170
54
120
170
72
120
170
18
140
200
36
140
200
54
140
200
72
140
200
18
120
170
36
120
170
54
120
170
72
120
170
18
120
-
36
120
-
54
120
-
72
120
-
240
This limit is monitored regardless of unit operation status, i.e. the limit is monitored at all times.
15, 20,
25
TEMPERATURE
LIMIT SWITCH 1, 2
OPENS, ºF
240
TEMPERATURE LIMIT
If the UCB senses zero volts from the high temperature
limit, the indoor blower motor is immediately energized.
HEATER
kW
460
600
The unit control board monitors the temperature limit
switch of electric heat units.
FLASH CODES
The control circuit includes the following safety controls:
1. Temperature Limit Switch (TLS 1, 2).
This control is located inside the heater compartment and is set to open at the temperature indicated in the Limit Control Setting Table 28. It resets
automatically. The limit switch operates when a
high temperature condition, caused by inadequate
supply air flow occurs, thus shutting down the
heater and energizing the blower.
2. Temperature Limit Switch (TLS 3, 4, 5 and 6).
This control is located inside the heater compartment and is set to open at the temperature indicated in the Limit Control Setting Table 28. It is a
manual reset limit. These limit switches will deenergize the heaters should the primary limit fail to
open or the contactors fail to open in a failure
mode.
60
The UCB will initiate a flash code associated with
errors within the system. Refer to UNIT CONTROL
BOARD FLASH CODES Table 33.
RESET
Remove the call for heating by lowering the thermostat
setting lower than the conditioned space temperature.
This resets any flash codes.
HEAT ANTICIPATOR SETPOINTS
It is important that the anticipator setpoint be correct.
Too high of a setting will result in longer heat cycles
and a greater temperature swing in the conditioned
space. Reducing the value below the correct setpoint
will give shorter "ON" cycles and may result in the lowering of the temperature within the conditioned space.
Refer to Table 29 for the required heat anticipator setting.
Unitary Products Group
127915-YIM-A-0405
TABLE 29: ELECTRIC HEAT ANTICIPATOR
SETPOINTS
HEATER
KW
VOLTAGE
SETTING, AMPS
TH1
TH2
18
0.29
-
36
0.29
0.29
54
208/230-3-60
0.29
0.58
72
0.29
0.58
18
0.29
-
36
0.29
0.29
54
460-3-60
0.29
0.29
72
0.29
0.29
18
0.29
-
36
0.29
0.29
0.29
0.29
0.29
0.29
54
575-3-60
72
GAS HEATING SEQUENCE OF OPERATIONS
The following sequence describes the operation of the
gas heat section.
When the thermostat calls for the first stage of heating,
the low-voltage control circuit from "R" to "W1" and "G"
is completed, thru the UCB. The heat relay "RW1" is
energized. The "RW1-2" contacts close energizing the
draft motor control. The draft motor control contacts
close and start the draft motor. As the speed of the
draft motor reaches approximately 2500 RPM, the centrifugal switch contact, located on the end of the draft
motor shaft, closes to power the first stage ignition
module "IC1", thru the "RW1-1 contacts.
Ignition module "IC1" will immediately start the first
stage igniter sparking and will open the redundant
valve located inside the first stage main gas valve
"GV1" to allow a flow of gas to only the first stage carryover tube. Only after the pilot flame has been ignited
and the presence of pilot flame detected at the "IC1" by
a signal sent back through the flame sensor is sparking
terminated and the first stage main gas valve opened.
Gas flows into each of the main burners and is ignited
from the carryover tube flame.
After completing the specified fan on delay for heating,
the UCB will energize the blower motor.
If "IC1" fails to detect a pilot flame, it will continue to try
for a maximum of 85 seconds to ignite the pilot tube. If
the pilot flame is not detected, then "IC1" will lock out
first stage furnace operation for five minutes or until
24V power is removed from the module either at the
unit or by resetting the room thermostat.
Unitary Products Group
When the thermostat calls for the second stage of
heating, the low-voltage control circuit from "R" to "W2"
is completed, thru the UCB. Heat relay "RW2" is energized. The "RW2-1" contact is closed energizing the
second stage ignition module "IC2". "IC2" will immediately start the second stage igniter sparking and will
open the redundant valve located inside the second
stage main gas valve "GV2" to allow a flow of gas to
the second stage carryover tube. Only after the pilot
flame has been ignited and the presence of pilot flame
detected at "IC2" by a signal sent back through the
flame sensor is sparking terminated and the main gas
valve opened.
Gas flows into each of the second stage main burners
and is ignited from the carryover tube flame.
If "IC2" fails to detect a pilot flame, it will continue to try
for a maximum of 85 seconds to ignite the pilot tube. If
the pilot flame is not detected, then "IC2" will lock out
first stage furnace operation for five minutes or until
24V power is removed from the module either at the
unit or by resetting the room thermostat.
NOTE: That the second stage furnace can operate
even if first stage has locked out.
When the thermostat satisfies de-energizing the
"RW2"and "RW1", thus opening all gas valves. The
blower motor will continue to run after the furnace is
shut down until the specified fan off delay for heating
has been satisfied. The UCB will de-energize the
blower motor.
REDUNDANT
VALVE
MAIN VALVE
GAS MAIN
GAS
VALVE
TO PILOT BURNER
TO MAIN
BURNER
FIGURE 23 - GAS VALVE PIPING
When the thermostat calls for the first stage of heating,
the low-voltage control circuit from "R" to "W1" is completed. A call for heat passes through the UCB to the
ignition control board (ICB). The UCB monitors the
"W1" call and acts upon any call for heat. Once voltage
has been sensed at “W1”, the UCB will initiate the fan
on delay for heating, energizing the indoor blower after
the specified delay has elapsed.
61
127915-YIM-A-0405
When the thermostat has been satisfied, heating calls
are ceased. The GV is immediately de-energized. The
blower is de-energized after the fan off delay for heating has elapsed. The draft motor performs a 25-second
post purge.
GAS HEATING OPERATION ERRORS
TEMPERATURE LIMIT
If the UCB senses zero volts from the high temperature
limit, the indoor blower motor is immediately energized.
When the UCB again senses 24 volts from the temperature limit, the draft motor will perform a 25-second
post-purge and the indoor blower will be de-energized
following the elapse of the fan off delay for heating.
This limit is monitored regardless of unit operation status, i.e. the limit is monitored at all times.
If the temperature limit opens three times within one
hour, it will lock-on the indoor blower motor and a flash
code is initiated (See Table 33).
GAS VALVE
The UCB continuously monitors the GV. Any time the
UCB senses voltage at the GV without a call for heat
for a continuous five-minute period, the UCB will lockon the indoor blower and a flash code is initiated
(Table 33). When voltage is no longer sensed at the
GV, the UCB will de-energize the indoor blower following the elapse of the fan off delay for heating.
If voltage has been sensed at the GV for at least 15
seconds during the fan on delay for heating and GV
voltage or "W1" is lost, the indoor blower is forced on
for the length of the fan off delay for heating.
down the ignition control and closing the main gas
valves and energizing the blower.
2. Centrifugal Switch (CS).
If the draft motor should fail, the centrifugal switch
attached to the shaft of the motor prevents the ignition controls and gas valves from being energized.
3. Redundant Gas Valve.
There are two separate gas valves in the furnace.
Each valve contains a main and a redundant valve.
The redundant valves are located upstream of the
main gas valves. Should either or both of the main
gas valves fail in the open position the redundant
valves serve as back-ups and shut off the flow of
gas.
4. Flame Sensor Rod / 100% Ignition Control LockOut.
The flame rods and controls are located per Proper
Flame Adjustment Figure 26. If an ignition control
fails to detect a signal from the flame sensor indicating the pilot flame is properly ignited, then the
main gas valve will not open. It will continue to try
and ignite the pilot for a maximum of 85 seconds,
then if the pilot flame is not detected, the ignition
control will lock out furnace operation until 24V
power is removed from the module either at the
unit or by resetting the room thermostat.
5. Rollout Switch.
The unit control board monitors the temperature limit
switch and the gas valve of gas furnace units.
This switch is located above the main burners in
the control compartment, which in the event of a
sustained main burner rollout shuts off and locks
out both ignition controls closing both gas valves.
The ignition controls lock out furnace operation
until 24V power is removed from the controls either
at the unit or by resetting the room thermostat.
The control circuit includes the following safety controls:
NOTE: The auto reset rollout switch must reset before
allowing furnace operation.
1. Limit Control (LS).
6. Auxiliary limit switch (AUX) -
SAFETY CONTROLS
This control is located inside the heat exchanger
compartment and is set to open at the temperature
indicated in the Limit Control Setting Table 30. It
resets automatically. The limit switch operates
when a high temperature condition, caused by
inadequate supply air flow occurs, thus shutting
62
This control is located inside the heat exchanger
compartment and is set to open at 190°F. It is a
manual reset switch. If AUX trips, then the primary
limit has not functioned correctly. Replace the primary limit.
Unitary Products Group
127915-YIM-A-0405
START-UP (COOLING)
TABLE 30: LIMIT CONTROL SETTING
CAPACITY, MBH
UNITS
(Tons)
INPUT
OUTPUT
LIMIT CONTROL
OPENS, ºF
15, 20, 25
300
240
195
15, 20, 25
400
320
195
PRESTART CHECK LIST
After installation has been completed:
1. Check the electrical supply voltage being supplied.
Be sure that it is the same as listed on the unit
nameplate.
2. Set the room thermostat to the off position.
IG N . C O N T R O L # 2
3. Turn unit electrical power on.
IG N . C O N T R O L # 1
4. Set the room thermostat fan switch to on.
R O L L O U T S W .
5. Check indoor blower rotation.
G V 1
G A S
V A L V E
S E N S O R # 1
G V 2
G A S
V A L V E
IG N IT O R # 2
•
If blower rotation is in the wrong direction.
Refer to Phasing Section in general information section.
•
Check blower drive belt tension.
IG N IT O R # 1
S E N S O R # 2
6. Check the unit supply air (CFM). See "CHECKING
SUPPLY AIR CFM" on page 52.
B U R N E R C O M P A R T M E N T
7. Measure evaporator fan motor's amp draw.
FIGURE 24 - GAS VALVE AND CONTROLS
FLASH CODES
9. Turn unit electrical power off.
The UCB will initiate a flash code associated with
errors within the system. Refer to UNIT CONTROL
BOARD FLASH CODES Table 33.
Remove the call for heating by lowering the thermostat
setting lower than the conditioned space temperature.
This resets any flash codes.
HEAT ANTICIPATOR SETPOINTS
It is important that the anticipator setpoint be correct.
Too high of a setting will result in longer heat cycles
and a greater temperature swing in the conditioned
space. Reducing the value below the correct setpoint
will give shorter "ON" cycles and may result in the lowering of the temperature within the conditioned space.
TABLE 31: GAS HEAT ANTICIPATOR SETPOINTS
Honeywell VR8440
White-Rodgers 36C68
Unitary Products Group
OPERATING INSTRUCTIONS
1. Turn unit electrical power on.
RESETS
GAS VALVE
8. Set the room thermostat fan switch to off.
ANTICIPATOR SETPOINT
1st STAGE
2nd STAGE
0.30 amp
0.11 amp
2. Set the room thermostat setting to lower than the
room temperature.
3. First stage compressors will energize after the
built-in time delay (five minutes).
4. The second stage of the thermostat will energize
second stage compressor if needed.
POST START CHECK LIST
1. Verify proper system pressures for both circuits.
2. Measure the temperature drop across the evaporator coil.
3. Measure the system Amperage draw across all
legs of 3 phase power wires.
4. Measure the condenser fan amp draw.
63
127915-YIM-A-0405
SHUT DOWN
1. Set the thermostat to highest temperature setting.
1. Check for gas leaks in the unit piping as well as the
supply piping.
2. Turn off the electrical power to the unit.
START-UP (GAS HEAT)
PRE-START CHECK LIST
Complete the following checks before starting the unit.
1. Check the type of gas being supplied. Be sure that
it is the same as listed on the unit nameplate.
2. Make sure that the vent and combustion air hoods
have been properly installed.
OPERATING INSTRUCTIONS
This furnace is equipped with an intermittent
pilot and automatic re-ignition system. DO
NOT attempt to manually light the pilot.
TO LIGHT PILOT AND MAIN BURNERS:
1. Turn “off” electric power to unit.
FIRE OR EXPLOSION HAZARD
Failure to follow the safety warning exactly
could result in serious injury, death or property
damage.
Never test for gas leaks with an open flame.
Use a commerically available soap solution
made specifically for the detection of leaks to
check all connections. A fire or explosion may
result causing property damage, personal
injury or loss of life.
2. Check for correct manifold gas pressures. See
“Checking Gas Input” page 65.
3. Check the supply gas pressure. It must be within
the limits shown on rating nameplate. Supply pressure should be checked with all gas appliances in
the building at full fire. At no time should the
standby gas line pressure exceed 13", nor the
operating pressure drop below 5.0" for natural gas
units. If gas pressure is outside these limits, contact the local gas utility for corrective action.
2. Turn room thermostat to lowest setting.
3. Turn gas valve knob or switch to “on” position.
4. Turn “on” electric power to unit.
5. Set room thermostat to desired temperature.
(If thermostat “set” temperature is above room temperature, pilot burner ignition will occur and, after
an interval to prove pilot flame, main burners will
ignite).
TO SHUT DOWN:
FIGURE 25 - TYPICAL GAS VALVES
1. Turn “off” electric power to unit.
2. Depress knob of gas valve while turning to “off”
position, or turn gas valve switch to “off” position.
POST-START CHECK LIST (GAS)
MANIFOLD GAS PRESSURE ADJUSTMENT
Small adjustments to the high-fire gas flow may be
made by turning the pressure regulator adjusting screw
on the automatic gas valve.
After the entire control circuit has been energized and
the heating section is operating, make the following
checks:
64
Unitary Products Group
127915-YIM-A-0405
Adjust as follows:
3. Remove the gas piping closure panel.
1. Remove the cap on the regulator. It's located next
to the push-on electrical terminals.
4. Disconnect wiring to the gas valves and spark ignitors. Remove the manifold-burner gas valve
assembly by lifting up and pulling back.
2. To decrease the gas pressure, turn the adjusting
screw counterclockwise.
3. To increase the gas pressure, turn the adjusting
screw clockwise.
NOTE: The correct manifold pressure for these furnaces is 3.65 IWG ±0.3.
B U R N E R A S S E M B L Y B R A C K E T
FIGURE 27 - TYPICAL FLAME APPEARANCE
F L A M E S E N S O R B U L B
Burners are now accessible for service.
Reverse the above procedure to replace the assemblies. Make sure that burners are level and seat at the
rear of the heat exchanger.
1 /8 " G A P B E T W E E N C A R R Y -O V E R
T U B E A N D F L A M E S E N S O R B U L B
C A R R Y -O V E R T U B E
BURNER AIR SHUTTER ADJUSTMENT
Adjust burner shutters so no yellow flame is observed
in the heat exchanger tubes.
FIGURE 26 - PROPER FLAME ADJUSTMENT
PILOT CHECKOUT
CHECKING GAS INPUT
NATURAL GAS
The pilot flame should envelope the end of the flame
sensor. To adjust pilot flame, (1) remove pilot adjustment cover screw, (2) increase or decrease the clearance for air to the desired level, (3) be sure to replace
cover screw after adjustment to prevent possible gas
leakage.
Put the system into operation and observe through
complete cycle to be sure all controls function properly.
BURNER INSTRUCTIONS
To check or change burners, pilot or orifices, CLOSE
MAIN MANUAL SHUT-OFF VALVE AND SHUT OFF
ALL ELECTRIC POWER TO THE UNIT.
1. Remove the screws holding either end of the manifold to the burner supports.
2. Open the union fitting in the gas supply line just
upstream of the unit gas valve and downstream
from the main manual shut-off valve.
Unitary Products Group
1. Turn off all other gas appliances connected to the
gas meter.
2. With the furnace turned on, measure the time
needed for one revolution of the hand on the smallest dial on the meter. A typical gas meter usually
has a 1/2 or a 1 cubic foot test dial.
3. Using the number of seconds for each revolution
and the size of the test dial increment, find the
cubic feet of gas consumed per hour from the Gas
Rate - Cubic Feet Per Hour Table 32.
If the actual input is not within 5% of the furnace rating
(with allowance being made for the permissible range
of the regulator setting), replace the orifice spuds with
spuds of the proper size.
NOTE: To find the Btu input, multiply the number of
cubic feet of gas consumed per hour by the
Btu content of the gas in your particular locality
(contact your gas company for this information
- it varies widely from city to city.)
65
127915-YIM-A-0405
TABLE 32: GAS RATE - CUBIC FEET PER HOUR
Seconds
for One
Rev.
Size of Test Dial
1/2 cu. ft.
1 cu. ft.
4
6
8
10
450
300
228
180
900
600
450
360
12
14
16
18
20
150
129
113
100
90
300
257
225
200
180
22
24
26
28
82
75
69
64
164
150
138
129
COOLING TROUBLESHOOTING GUIDE
Example: By actual measurement, it takes 13 seconds for the hand on the 1cubic foot dial to make a revolution with just a 300,000 Btuh furnace running.
Read across to the column in the table above, headed “1 Cubic Foot”, where
you will see that 278 cubic feet of gas per hour are consumed by the furnace at
that rate. Multiply 278 x 1050 (the Btu rating of the gas obtained from the local
gas company). The result is 292,425 Btuh, which is close to the 300,000 Btuh
rating of the furnace.
ADJUSTMENT OF TEMPERATURE RISE
The temperature rise (or temperature difference
between the return air and the heated air from the furnace) must lie within the range shown on the rating
plate and the data in the Gas Heat Application Table 4.
CFM =
TROUBLESHOOTING
Btuh Input x 0.8
108
. x oF Temp. Rise
After the temperature rise has been determined, the
cfm can be calculated as follows:
After about 20 minutes of operation, determine the furnace temperature rise. Take readings of both the return
air and the heated air in the ducts (about six feet from
the furnace) where they will not be affected by radiant
heat. Increase the blower cfm to decrease the temperature rise; decrease the blower cfm to increase the
rise. Refer to the Blower Motor and Drive Data
Table 27.
BELT DRIVE BLOWER
All units have belt drive single-speed blower motors.
The variable pitch pulley on the blower motor can be
adjusted to obtain the desired supply air CFM.
Troubleshooting of components may require
opening the electrical control box with the
power connected to the unit. Use extreme care
when working with live circuits! Check the
unit nameplate for the correct line voltage and
set the voltmeter to the correct range before
making any connections with line terminals.
Shut off all electric power to the unit prior to
any of the following maintenance procedures
to prevent personal injury.
Label all wires prior to disconnection when servicing controls. Wiring errors can cause
improper and dangerous operation, which
could cause injury to person and/or damage
unit components. Verify proper operation after
servicing.
On calls for cooling, if the compressors are operating
but the supply air blower motor does not energize after
a short delay (the room thermostat fan switch is in the
“AUTO” position).
1. Turn the thermostat fan switch to the ON position.
If the supply air blower motor does not energize, go
to Step 3.
2. If the blower motor runs with the fan switch in the
ON position but will not run after the first compressor has energized when the fan switch is in the
AUTO position, check the room thermostat for contact between R and G in the AUTO position during
calls for cooling.
3. If the supply air blower motor does not energize
when the fan switch is set to ON, check that line
voltage is being supplied to the contacts of the M3,
contactor, and that the contactor is pulled in. Check
for loose wiring between the contactor and the supply air blower motor.
4. If M3 is pulled in and voltage is supplied to M3,
lightly touch the supply air blower motor housing. If
it is hot, the motor may be off on internal
66
Unitary Products Group
127915-YIM-A-0405
protection. Cancel any thermostat calls and set the
fan switch to AUTO. Wait for the internal overload
to reset. Test again when cool.
5. If M3 is not pulled in, check for 24 volts at the M3
coil. If 24 volts are present at M3 but M3 is not
pulled in, replace the contactor.
6. Failing the above, if there is line voltage supplied at
M3, M3 is pulled in, and the supply air blower
motor still does not operate, replace the motor.
7. If 24 volts is not present at M3, check that 24 volts
is present at the UCB supply air blower motor terminal, “FAN”. If 24 volts is present at the FAN,
check for loose wiring between the UCB and M3.
8. If 24 volts is not present at the “FAN” terminal,
check for 24 volts from the room thermostat. If 24
volts are not present from the room thermostat,
check for the following:
a.
Proper operation of the room thermostat (contact
between R and G with the fan switch in the ON position and in the AUTO position during operation
calls).
b.
Proper wiring between the room thermostat and the
UCB.
c.
Loose wiring from the room thermostat to the UCB.
9. If 24 volts is present at the room thermostat but not
at the UCB, check for proper wiring between the
thermostat and the UCB, i.e. that the thermostat G
terminal is connected to the G terminal of the UCB,
and for loose wiring.
10. If the thermostat and UCB are properly wired,
replace the UCB.
On calls for cooling, the supply air blower motor is
operating but compressor #1 is not (the room thermostat fan switch is in the “AUTO” position).
1. If installed, check the position of the economizer
blades. If the blades are open, the economizer is
providing free cooling and the compressors will not
immediately operate. If both stages of cooling are
requested simultaneously and the economizer provides free cooling, following a short delay compressor #1 will be energized unless it is locked out. If
compressor #1 is locked out, compressor #2 is
energized. Compressor #2 is always energized in
place of compressor #1 when compressor #1 is
Unitary Products Group
requested but locked out, unless this option has
been disabled through computer communications.
2. If no economizer is installed or the economizer is
not opening to provide free cooling and compressor #1 does not energize on a call for cooling,
check for line voltage at the compressor contactor,
M1, and that the contactor is pulled in. Check for
loose wiring between the contactor and the compressor.
3. If M1 is pulled in and voltage is supplied at M1,
lightly touch the compressor housing. If it is hot, the
compressor may be off on inherent protection.
Cancel any calls for cooling and wait for the internal overload to reset. Test again when cool.
4. If M1 is not pulled in, check for 24 volts at the M1
coil. If 24 volts are present and M1 is not pulled in,
replace the contactor.
5. Failing the above, if voltage is supplied at M1, M1
is pulled in, and the compressor still does not operate, replace the compressor.
6. If 24 volts is not present at M1, check for 24 volts at
the UCB terminal, C1. If 24 volts is present, check
for loose wiring between C1 and the compressor
contactor.
7. If 24 volts is not present at the C1 terminal, check
for 24 volts from the room thermostat at the UCB
Y1 terminal. If 24 volts is not present from the room
thermostat, check for the following:
a.
24 volts at the thermostat Y1 terminal.
b.
Proper wiring between the room thermostat and the
UCB, i.e. Y1 to Y1, Y2 to Y2.
c.
Loose wiring from the room thermostat to the UCB.
8. If 24 volts is present at the UCB Y1 terminal, the
compressor may be out due to an open high-pressure switch, low-pressure switch, or freezestat.
Check for 24 volts at the HPS1, LPS1, and FS1
terminals of the UCB. If a switch has opened, there
should be a voltage potential between the UCB terminals, e.g. if LPS1 has opened, there will be a 24volt potential between the LPS1 terminals.
9. If 24 volts is present at the UCB Y1 terminal and
none of the protection switches have opened, the
UCB may have locked out the compressor for
repeat trips. The UCB should be flashing an alarm
code. If not, press and release the ALARMS button
67
127915-YIM-A-0405
on the UCB. The UCB will flash the last five alarms
on the LED. If the compressor is locked out, cancel
any call for cooling. This will reset any compressor
lock outs.
NOTE: While the above step will reset any lockouts,
compressor #1 may be held off for the ASCD.
See the next step.
10. If 24 volts is present at the UCB Y1 terminal and
none of the switches are open and the compressor
is not locked out, the UCB may have the compressor in an ASCD. Check the LED for an indication of
an ASCD cycle. The ASCD should time out within
5 minutes. Press and release the TEST button to
reset all ASCDs.
11. If 24 volts is present at the UCB Y1 terminal and
the compressor is not out due to a protective
switch trip, repeat trip lock out, or ASCD, the economizer terminals of the UCB may be improperly
wired. Check for 24 volts at the Y1 “OUT” terminal
of the UCB. If 24 volts is present, trace the wiring
from Y1 “OUT” for incorrect wiring. If 24 volts is not
present at the Y1 “OUT” terminal, the UCB must be
replaced.
12. For units without economizers:If 24 volts is present
at the Y1 OUT terminal, check for 24 volts at the
Y1 “ECON” terminal. If 24 volts is not present,
check for loose wiring from the Y1 “OUT” terminal
to the Mate-N-Lock plug, the jumper in the Mate-NLock plug, and in the wiring from the Mate-N-Lock
plug to the Y1 “ECON” terminal.
13. For units with economizers: If 24 volts is present at
the Y1 “OUT” terminal, check for 24 volts at the Y1
“ECON” terminal. If 24 volts is not present, check
for loose wiring from the Y1 “OUT” terminal to the
Mate-N-Lock plug, a poor connection between the
UCB and economizer Mate-N-Lock plugs, loose
wiring from the Mate-N-Lock plug to the economizer, back to the Mate-N-Lock plug, and from the
Mate-N-Lock plug to the Y1 “ECON” terminal. If
nothing is found, the economizer actuator may
have faulted and is failing to return the 24-volt “call”
to the Y1 “ECON” terminal even though the economizer is not providing free cooling. To test, disconnect the Mate-N-Locks and jumper between the
WHITE and YELLOW wires of the UCB’s Mate-NLock plug. If compressor #1 energizes, there is a
fault in the economizer wiring or actuator.
68
14. The UCB can be programmed to lock out compressor operation during free cooling and in low ambient conditions. These options are not enabled by
default. Local distributors can test the UCB for this
programming.
15. If none of the above corrected the error, test the
integrity of the UCB. Disconnect the C1 terminal
wire and jumper it to the Y1 terminal. DO NOT
jump the Y1 to C1 terminals. If the compressor
engages, the UCB has faulted.
16. If none of the above correct the error, replace the
UCB.
On calls for the second stage of cooling, the supply air
blower motor and compressor #1 are operating but
compressor #2 is not (the room thermostat fan switch
is in the “AUTO” position).
1. If installed, check the position of the economizer
blades. If the blades are open, the economizer is
providing free cooling. If the second stage of cooling is requested, following a short delay, compressor #1 will be energized unless it is locked out.
Typically, compressor #2 is energized only during
free cooling if the call for the second stage of cooling persists for 20 minutes.
2. Compressor #2 will not energize simultaneously
with compressor #1 if a call for both stages of cooling is received. The UCB delays compressor #2 by
30 seconds to prevent a power surge. If after the
delay compressor #2 does not energize on a second stage call for cooling, check for line voltage at
the compressor contactor, M2, and that the contactor is pulled in. Check for loose wiring between the
contactor and the compressor.
3. If M2 is pulled in and voltage is supplied at M2,
lightly touch the compressor housing. If it is hot, the
compressor may be off on inherent protection.
Cancel any calls for cooling and wait for the internal overload to reset. Test again when cool.
4. If M2 is not pulled in, check for 24 volts at the M2
coil. If 24 volts is present and M2 is not pulled in,
replace the contactor.
5. Failing the above, if voltage is supplied at M2, M2
is pulled in, and the compressor still does not operate, replace the compressor.
Unitary Products Group
127915-YIM-A-0405
6. If 24 volts is not present at M2, check for 24 volts at
the UCB terminal, C2. If 24 volts are present,
check for loose wiring between C2 and the compressor contactor.
7. If 24 volts is not present at the C2 terminal, check
for 24 volts from the room thermostat at the UCB
Y2 terminal. If 24 volts is not present from the room
thermostat, check for the following:
a.
24 volts at the thermostat Y2 terminal.
b.
Proper wiring between the room thermostat and the
UCB, i.e. Y1 to Y1, Y2 to Y2.
c.
Loose wiring from the room thermostat to the UCB.
8. If 24 volts is present at the UCB Y2 terminal, the
compressor may be out due to an open high-pressure switch, low-pressure switch, or freezestat.
Check for 24 volts at the HPS2, LPS2, and FS2
terminals of the UCB. If a switch has opened, there
should be a voltage potential between the UCB terminals, e.g. if LPS2 has opened, there will be 24
volts of potential between the LPS2 terminals.
9. If 24 volts is present at the UCB Y2 terminal and
none of the protection switches have opened, the
UCB may have locked out the compressor for
repeat trips. The UCB should be flashing a code. If
not, press and release the ALARMS button on the
UCB. The UCB will flash the last five alarms on the
LED. If the compressor is locked out, remove any
call for cooling at the thermostat or by disconnecting the thermostat wiring at the Y2 UCB terminal.
This will reset any compressor lock outs.
NOTE: While the above step will reset any lock outs,
compressor #1 will be held off for the ASCD,
and compressor #2 may be held off for a portion of the ASCD. See the next step.
10. If 24 volts is present at the UCB Y2 terminal and
none of the switches are open and the compressor
is not locked out, the UCB may have the compressor in an ASCD. Check the LED for an indication of
an ASCD cycle. The ASCD should time out within
5 minutes. Press and release the TEST button to
reset all ASCDs.
11. The UCB can be programmed to lock out compressor operation during free cooling and in low ambient conditions. These options are not enabled by
default. Local distributors can test the UCB for this
programming.
Unitary Products Group
12. If none of the above corrected the error, test the
integrity of the UGB. Disconnect the C2 terminal
wire and jumper it to the Y2 terminal. DO NOT
jump the Y2 to C2 terminals. If the compressor
engages, the UCB has faulted.
13. If none of the above correct the error, replace the
UCB.
On a call for cooling, the supply air blower motor and
compressor #2 are operating but compressor #1 is not
(the room thermostat fan switch is in the “AUTO” position).
1. Compressor #2 is energized in place of compressor #1 when compressor #1 is unavailable for cooling calls. Check the UCB for alarms indicating that
compressor #1 is locked out. Press and release
the ALARMS button if the LED is not flashing an
alarm.
2. Check for line voltage at the compressor contactor,
M1, and that the contactor is pulled in. Check for
loose wiring between the contactor and the compressor.
3. If M1 is pulled in and voltage is supplied at M1,
lightly touch the compressor housing. If it is hot, the
compressor may be off on inherent protection.
Cancel any calls for cooling and wait for the internal overload to reset. Test again when cool.
4. If M1 is not pulled in, check for 24 volts at the M1
coil. If 24 volts is present and M1 is not pulled in,
replace the contactor.
5. Failing the above, if voltage is supplied at M1, M1
is pulled in, and the compressor still does not operate, replace the compressor.
6. If 24 volts is not present at M1, check for 24 volts at
the UCB terminal, C1. If 24 volts is present, check
for loose wiring between C1 and the compressor
contactor.
7. If 24 volts is not present at the C1 terminal, check
for 24 volts from the room thermostat at the UCB
Y1 terminal. If 24 volts are not present at the UCB
Y1 terminal, the UCB may have faulted. Check for
24 volts at the Y1 ECON terminal. If 24 volts is not
present at Y1 “ECON”, the UCB has faulted. The
UCB should de-energize all compressors on a loss
of call for the first stage of cooling, i.e. a loss if 24
volts at the Y1 terminal.
69
127915-YIM-A-0405
8. If 24 volts are present at the UCB Y1 terminal, the
compressor may be out due to an open high-pressure switch, low-pressure switch, or freezestat.
Check for 24 volts at the HPS1, LPS1, and FS1
terminals of the UCB. If a switch has opened, there
should be a voltage potential between the UCB terminals, e.g. if LPS1 has opened, there will be a 24volt potential between the LPS1 terminals.
9. If 24 volts is present at the UCB Y1 terminal and
none of the protection switches have opened, the
UCB may have locked out the compressor for
repeat trips. The UCB should be flashing a code. If
not, press and release the ALARMS button on the
UCB. The UCB will flash the last five alarms on the
LED. If the compressor is locked out, remove any
call for cooling. This will reset any compressor lock
outs.
NOTE: While the above step will reset any lock outs,
compressor #2 will be held off for the ASCD,
and compressor #1 may be held off for a portion of the ASCD. See the next step.
“ECON” terminal. If 24 volts is not present, check
for loose wiring from the Y1 “OUT” terminal to the
Mate-N-Lock plug, a poor connection between the
UCB and economizer Mate-N-Lock plugs, loose
wiring from the Mate-N-Lock plug to the economizer, back to the Mate-N-Lock plug, and from the
Mate-N-Lock plug to the Y1 “ECON” terminal. The
economizer board may have faulted and is not
returning the 24 volts to the Y1 “ECON” terminal
even though the economizer is not providing free
cooling. To test the economizer board, disconnect
the Mate-N-Locks and jumper between the WHITE
and YELLOW wires of the UCB’s Mate-N-Lock
plug.
13. The UCB can be programmed to lock out compressor operation during free cooling and in low ambient conditions. These options are not enabled by
default. They can be checked by local distributors.
14. If none of the above correct the error, replace the
UCB.
GAS HEAT TROUBLESHOOTING GUIDE
10. If 24 volts is present at the UCB Y1 terminal and
none of the switches are open and the compressor
is not locked out, the UCB may have the compressor in an ASCD. Check the LED for an indication of
an ASCD cycle. The ASCD should time out within
5 minutes. Press and release the TEST button to
reset all ASCDs.
11. If 24 volts is present at the UCB Y1 terminal and
the compressor is not out due to a protective
switch trip, repeat trip lock out, or ASCD, the economizer terminals of the UCB may be improperly
wired. Check for 24 volts at the Y1 “OUT” terminal
of the UCB. If 24 volts is present, trace the wiring
from Y1 “OUT” for incorrect wiring. If 24 volts is not
present at the Y1 “OUT” terminal, the UCB must be
replaced.
12. For units without economizers: If 24 volts is present
at the Y1 “OUT” terminal, check for 24 volts at the
Y1 “ECON” terminal. If 24 volts is not present,
check for loose wiring from the Y1 “OUT” terminal
to the Mate-N-Lock plug, the jumper in the Mate-NLock plug, and in the wiring from the Mate-N-Lock
plug to the Y1 “ECON” terminal.
For units with economizers: If 24 volts is present at
the Y1 “OUT” terminal, check for 24 volts at the Y1
70
Troubleshooting of components may require
opening the electrical control box with the
power connected to the unit. Use extreme
care when working with live circuits! Check
the unit nameplate for the correct line voltage
and set the voltmeter to the correct range
before making any connections with line terminals.
When not necessary, shut off all electric power
to the unit prior to any of the following maintenance procedures so as to prevent personal
injury.
Label all wires prior to disconnection when servicing controls. Wiring errors can cause
improper and dangerous operation, which
could cause injury to person and/or damage
unit components. Verify proper operation after
servicing.
Unitary Products Group
127915-YIM-A-0405
NOTE: To find the Btu input, multiply the number of
cubic feet of gas consumed per hour by the
Btu content of the gas in your particular locality
(contact your gas company for this information
- it varies widely from city to city.).
The furnace may shut down on a high temperature condition during the procedure. If
this occurs, the UCB energize the supply air
blower motor until the high temperature limit
has reset. Caution should be used at all
times as the supply air blower may energize
regardless of the room thermostat fan switch
position.
On calls for heating, the draft motor operates and the
furnace lights but the supply air blower motor does not
energize after a short delay (the room thermostat fan
switch is in “AUTO” position).
1. Place the thermostat fan switch in the “ON” position. If the supply air blower motor energizes, go to
Step 10.
2. If the supply air blower motor does not energize
when the fan switch is set to “ON,” check that line
voltage is being supplied to the contacts of the M3
contactor, and that the contactor is pulled in. Check
for loose wiring between the contactor and the supply air blower motor.
3. If M3 is pulled in and voltage is supplied at M3,
lightly touch the supply air blower motor housing. If
it is hot, the motor may be off on inherent protection. Cancel any thermostat calls and set the fan
switch to “AUTO”, wait for the internal overload to
reset. Test again when cool.
4. If M3 is not pulled in, check for 24 volts at the M3
coil. If 24 volts is present at M3 but M3 is not pulled
in, replace the contactor.
5. Failing the above, if there is line voltage supplied at
M3, M3 is pulled in, and the supply air blower
motor still does not operate, replace the motor.
6. If 24 volts is not present at M3, check that 24 volts
is present at the supply air blower motor terminal
on the UCB. If 24 volts is present at the UCB termi-
Unitary Products Group
nal, check for loose wiring between the UCB and
M3.
7. If 24 volts is not present at the UCB supply air
blower motor terminal, check for 24 volts from the
room thermostat. If 24 volts is not present from the
room thermostat, check for the following:
a.
Proper operation of the room thermostat (contact
between R and G with the fan switch in the “ON”
position and in the “AUTO” position during operation
calls).
b.
Proper wiring between the room thermostat and the
UCB.
c.
Loose wiring from the room thermostat to the UCB.
8. If 24 volts is present at the room thermostat but not
at the UCB, check for proper wiring between the
thermostat and the UCB, i.e. that the thermostat G
terminal is connected to the G terminal of the UCB,
and for loose wiring.
9. If the thermostat and UCB are properly wired,
replace the UCB.
10. If the blower motor runs with the fan switch in the
“ON” position but does not run shortly after the furnace has ignited when the fan switch is in the
“AUTO” position, check the room thermostat for
contact between R and G during “W1” calls.
On calls for heating, the supply air blower operates but
the draft motor does not (the room thermostat fan
switch is in the “AUTO” position).
1. The draft motor has inherent protection. If the
motor shell is hot to the touch, wait for the internal
overload to reset.
2. If the motor shell is cold with the room thermostat
calling for heat, check for line voltage at the
motor's Mate-N-Lok connector attached to the
evaporator partition. If line voltage is present,
replace the draft motor.
3. If line voltage is not present, check for line voltage
at the heat relay (RW1) contacts in the main control box and check to see if the (RW1) is pulled in.
4. If the (RW1) relay is pulled in, check for a loose line
voltage connection.
71
127915-YIM-A-0405
5. If the (RW1) relay is not pulled in, check for 24 volts
at the (RW1) coil. If 24 volts is present, replace the
(RW1) relay. If 24 volts is not present, check for a
loose 24 volt connection back to the relay board
and check the connections from the room thermostat to the relay board. If all connections are correct, replace the relay board.
The draft motor runs but the furnace does not light and
the sparker does not spark.
1. The ignition control (IC1, IC2) may be locked out
due to either a flame roll out or 100% shut off.
These safety features are described above. If lockout has occurred, 24V must be removed from the
ignition controls. This is done at the unit or by
resetting the room thermostat. After resetting 24V,
check for proper furnace operation. If lock-out continues to occur, locate the source of the problem
and correct.
2. Check all 24 volt connections from the relay board
to and in the gas heat section. Check low voltage
connections to the (ETD) located in the control
box.
3. If the furnace is hot, it may be out on an over-temperature condition, wait for limit reset.
4. If the furnace is cold, check for 24 volts at wire 241
attached to the electrical time delay (ETD) located
in the main control box. If 24 volts is not found,
replace the ETD.
5. 24 volts is found at wire 241, remove the wires
attached to the (TDR) and with a VOM, check for
continuity across contacts 1 and 2. If none is found,
the (TDR) is open and must be replaced. If there is
continuity, re-attach the wires.With the draft motor
running, check for 24 volts at terminal 4 of (RW1-2)
and (RW2-1). If 24 volts is not present, the centrifugal switch (CS) has not closed or has gone bad.
Check the line voltage to the unit - if it is correct,
replace the draft motor. If line voltage is low, call
the power company.
6. Check for 24V at terminal 2 of (RW1-2 and RW21). If 24V is not present, check for 24V at (RW1
and RW2) relay coils. If these relays are pulled in,
then check for a loose connection at terminal 2 and
terminal 4 of each relay. If no problem is found,
then replace (RW1 and/or RW2) as required.
72
7. If 24 volts is present at the ignitor controls, check
all control wiring at the ignitor controls and the high
tension wire to the ignitors. Check that the ground
wires from the ignitor controls, the gas valves and
pilot burners are all intact and making good electrical connection. Check to make sure that the
ceramic insulator on the pilot ignitors or sensors is
not broken or cracked, if all are intact, replace the
ignition control IC1 or IC2.
The draft motor runs and the ignitor sparks at the pilot
burner but the pilot does not ignite and a gas odor is
not detected at the draft motor outlet.
1. Check to make sure gas is being supplied to the
unit. Make sure that the gas pressure to the unit is
within the proper limits as described in the “POST
START CHECK LIST” page 64 and that the pilot
adjust screw is allowing some flow of gas as
described in “PILOT CHECKOUT” page 65.
2. Check all wiring between the ignitor control and the
gas valve. Check to make sure the ground connections are intact.
3. If the wiring is intact, check for 24 volts across terminals “PV” and “COMMON” on the ignitor control.
If 24 volts is not present, replace the ignitor control.
4. If 24 volts is present, remove the pilot burner and
remove the pilot orifice from the pilot burner. The
orifice is removed in the direction opposite the flow
of gas. Inspect the orifice for obstruction. If it is
clear, replace the main gas valve.
The ignitor sparks at the pilot burner but the pilot does
not ignite and a gas odor is detected at the draft motor
outlet.
1. Adjust the pilot adjust screw on the gas valve as
described in “PILOT CHECKOUT” page 65.
2. Check the supply pressure as described in “POST
START CHECK LIST” page 64. Make adjustments
as necessary.
3. Check the pilot orifice and carryover tube for
obstruction as described in paragraph above.
Clean as needed but the problem should not be the
gas valve.
Unitary Products Group
127915-YIM-A-0405
The pilot burner ignites but the ignitor continues to
spark and the main burners do not ignite.
Do not confuse this with an error flash code. To prevent
confusion, a 1-flash, flash code is not used.
1. Make the same checks and adjustment as
described in “PILOT CHECKOUT” page 65.
Current alarms or active restrictions are flashed on the
UCB LED. Pressing and releasing the ALARMS button
on the UCB can check the alarm history. The UCB will
cycle through the last five (5) alarms, most recent to
oldest, separating each alarm flash code by approximately 2 seconds.
2. Check the supply pressure as described in “POST
START CHECK LIST” page 64. Make adjustments
as necessary.
3. Make sure that the pilot burner is not bent or damaged.
4. Make sure that the ground connections at the pilot
burner, gas valve and ignitor control are intact.
Check the high tension wire for good electrical connection. If all are intact, replace the ignitor module.
In some cases, it may be necessary to "zero" the
ASCD for the compressors in order to perform troubleshooting. To reset all ASCDs for one cycle, press and
release the UCB TEST button once.
TABLE 33: UNIT CONTROL BOARD FLASH CODES
Flash Code
Description
On Steady
Control Failure - Replace Control
The pilot burner lights and the spark stops but the main
burners do not light.
Heart Beat
Normal Operation
1. Check electrical connections between the ignitor
control and the gas valve. If intact, check for 24
volts across terminals “MV” and “COMMON” terminals. If no voltage detected, replace ignitor control.
If voltage is present, replace gas valve.
2 Flashes
Control waiting ASCD1
3 Flashes
HPS1 - Compressor Lock out
4 Flashes
HPS2 - Compressor Lock out
5 Flashes
LPS1 - Compressor Lock out
Furnace lights with roll-out or one burner has delayed
ignition.
6 Flashes
LPS2 - Compressor Lock out
7 Flashes
FS1 - Compressor Lock out
1. Make sure that the carryover is aligned properly
with the flame sensor as described in “PILOT
CHECKOUT” page 65.
8 Flashes
FS2 - Compressor Lock out
9 Flashes
Ignition Control Locked Out/
Ignition Control Failure / Limit Switch Trip /
No Jumper Plug in Heat Section
10 Flashes
Compressors Locked Out On Low
Outdoor Air Temperature1
11 Flashes
Compressors Locked Out Because The
Economizer Is Using Free Cooling1
12 Flashes
Fan Overload Switch Trip
13 Flashes
Compressor Held Off Due To Low Voltage1
14 Flashes
EEPROM Storage Failure (Control Failure)
Main burners light but exhibit erratic flame characteristics.
1. Adjust air shutters as described in “BURNER AIR
SHUTTER ADJUSTMENT” page 65.
2. Check the main burner orifices for obstruction and
alignment. Removal procedure is described in
BURNER INSTRUCTIONS page 65. Clean or
replace burner orifices and burners as needed.
1 Flash
OFF
UNIT FLASH CODES
Various flash codes are utilized by the unit control
board (UCB) to aid in troubleshooting. Flash codes are
distinguished by the short on and off cycle used
(approximately 200ms on and 200ms off). To show
normal operation, the control board flashes a 1 second
on, 1 second off "heartbeat" during normal operation.
This is to verify that the UCB is functioning correctly.
Unitary Products Group
1.
Not Applicable
No Power or Control Failure
These flash codes do not represent alarms.
The control will flash 250ms on and 250ms off for status codes. The control will separate the flash codes
with a 2 second off delay between flash codes. Under
normal operation, the control will flash the LED at a
rate of, 1 second on and 1 second off. This will be the
“Heart Beat”.
73
127915-YIM-A-0405
TABLE 34: REHEAT CONTROL BOARD FLASH
CODES
FLASH CODES
DESCRIPTION
On Steady
This is a Control Failure
1 Flash
Not Applicable
2 Flashes
Hot Gas Reheat is on with Y1 Output
(No Call for Cooling)
3 Flashes
Y1, Y2, and Hot Gas Reheat is on because of
a call for Y1 and Humidistat. See alt operation
OFF
No Power or Control Failure
74
Unitary Products Group
127915-YIM-A-0405
Unitary Products Group
75
Subject to change without notice. Printed in U.S.A.
Copyright © 2005 by Unitary Products Group. All rights reserved.
Unitary
Products
Group
127915-YIM-A-0405
Supersedes: 98833-YIM-A-1104
5005
York
Drive
Norman
OK
73069