Digiop BLK-IPD104 User manual

H.264 Indoor/Outdoor Dome
IP Camera User Manual
Product: BLK-IPD104
Please read this manual before using your camera, and always follow the instructions for
safety and proper use. Save this manual for future reference.
BLK-IPD104_CM
10/26/11

CAUTION
Do not operate this camera in environments where the temperatures or humidity is outside the recommended range.
Doing so my cause electric shock and shorten the life of the product.
LEGAL NOTICE
DIGIOP® products are designed to meet safety and performance standards with the use of specific DIGIOP
authorized accessories. DIGIOP disclaims liability associated with the use of non-DIGIOP authorized accessories.
The recording, transmission, or broadcast of any person’s voice without their consent or a court order is strictly
prohibited by law.
DIGIOP makes no representations concerning the legality of certain product applications such as the making,
transmission, or recording of video and/or audio signals of others without their knowledge and/or consent. We
encourage you to check and comply with all applicable local, state, and federal laws and regulations before
engaging in any form of surveillance or any transmission of radio frequencies.
Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks
and names or their products. DIGIOP, Inc. disclaims any proprietary interest in trademarks and trade names other
than its own.
Microsoft, Windows, and Internet Explorer are either registered trademarks or trademarks of Microsoft Corporation in
the United States and/or other countries. SONY is a trademark or registered trademark of Sony Corporation or any
of its affiliates.
No part of this document may be reproduced or distributed in any form or by any means without the express written
permission of DIGIOP, Inc.
© 2011 DIGIOP, Inc. All Rights Reserved.
3850 Priority Way South Drive, Suite 200, Indianapolis, IN 46240
Sales/Support: 1.877.972.2522
ii
www.digiop.com
Table of Contents
SECTION 1
SECTION 2
SECTION 3
APPENDIX A
APPENDIX B
APPENDIX C
Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Installation and Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2.1 What’s in the box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2.2 Tools you need. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2.3 Mount the camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2.4 Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.4.1 Audio in/out connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.4.2 Sensor in (DI) connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.4.3 Alarm out (DO) connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.4.4 RS-485 device connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
2.4.5 Video out connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
2.4.6 LAN and power connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.5 Install IPAdmin Tool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.6 Configure the camera network settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.6.1 Configuring cameras on networks with DHCP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.6.2 Configuring cameras on networks without DHCP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.7 Setup the camera Basic Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
2.8 Aim, focus, and image quality adjustment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
2.8.1 Aim . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
2.8.2 Focus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
2.8.3 Image quality adjustments. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
2.9 Speaker/microphone setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
2.10 Cleaning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
A.1 Reboot camera. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
A.2 Set camera to factory default network settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
A.3 Checking your Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
A.4 Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Power over Ethernet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
C.1 PoE compatibility. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
C.2 Power classification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
H.264 Indoor/Outdoor Dome IP Camera
1
SECTION 1: FEATURES
SECTION 1
Features
The DIGIOP Black BLK-IPD104 is a professional, premium-grade dome camera designed for outdoor or indoor installation. It features:
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Fixed vandal-proof dome
Gimbal mounted camera
Sony® 1/3” Super HAD CCD sensor and High Quality SS-HQ1 full kit chipset
True day/night ICR and WDR
Dual streaming mode
De-interlacing on DSP
Supports burnt-in text, unicast/multicast
Video compression: H.264/MPEG-4/MJPEG 30 fps @ D1
Audio compression: G.711 (µLaw, aLaw)/PCM
Supports motion detection, 2-way mono audio support, analog video out for external monitor
Supports 10/100 Base-T Ethernet, RTSP/ HTTP protocol support
RS485 support
PoE support
Micro SD card support
OSD support
Software development kit (SDK) available
Video Content Analysis features
LAN/power
extension cable
socket
Micro SD
card slot
Power
adapter
connector
Reset
button
LAN connector
Terminal block
connector
BLK-IPD104 camera without the dome cover
2
www.digiop.com
SECTION 2: INSTALLATION AND SETUP
SECTION 2
Installation and Setup
2.1 What’s in the box
Your dome camera includes the following:
•
•
•
•
•
•
•
BLK-IPD104 camera
DC power adapter with power plugs for different powering sources
Base seal (surface cushion)
Power extension cable
11-pin terminal block
Hardware installation kit with a hex wrench, 3 screws and wall inserts
CD with application software, software manual, and camera documentation
2.2 Tools you need
To install the camera, you will need:
•
•
Phillips #2 screwdriver
PC with Microsoft® Windows® XP SP3 or newer, 32- or 64-bit system
Depending on how the camera is mounted, you may also need:
•
•
•
Hammer
Drill with bits for drilling mounting holes
1-3/8” hole saw
2.3 Mount the camera
1.
Determine where the camera will be mounted and record the Media Access Control (MAC) address of the camera. The MAC
address can be found on the label on the base of the camera. Record the information in the following table.
Location:
MAC address:
2.
Separate the camera dome from the camera base housing by loosening the three captive screws with the hex wrench
provided.
H.264 Indoor/Outdoor Dome IP Camera
3
SECTION 2: INSTALLATION AND SETUP
Camera dome removal
3.
Using the base as a template, mark the location of the three mounting screw holes.
4.
Drill mounting screw holes into the mounting surface:
——
——
——
If the mounting surface is a soft material, such as a drywall, drill and install drywall inserts for the mounting screws.
OR
If the mounting surface is a very soft material, such as ceiling tile, place a wood block behind the tile and drill holes for
mounting screws long enough to secure the base to the block.
OR
If mounting the camera on a hard surface, such as wood, drill the mounting screw holes into the surface before
attaching the camera.
5.
Determine the extension cable routing. If the cable is to be routed through the hole in the bottom of the base, perform the
following steps. If the cable will be routed through the conduit port in the side of the base and routed to a nearby junction
box, skip to step 9.
6.
While holding the camera in its mounting position, align the mounting screw holes in the base with the holes drilled for the
mounting screws. Mark the location of hole for the extension cable routing.
7.
Drill a 1-3/8” hole through the mounting surface for the extension cable.
8.
If you are routing interface cables through conduit attached to the bottom of the base, do the following:
4
www.digiop.com
SECTION 2: INSTALLATION AND SETUP
9.
a.
Unplug the extension cable from the camera electronics and remove it from the camera.
b.
Install a conduit fitting onto the bottom of the base.
c.
Install a junction box close enough to the camera for the extension cable LAN and power connectors to be in the box.
Attach the conduit for the junction box to the conduit fitting on the bottom of the camera base.
Place the base seal over the base, aligning the holes for the mounting screws. Attach the camera and seal to the surface with
three screws. Skip to step 15.
10. Unplug the extension cable from the camera electronics and remove it from the camera.
11.
Remove the conduit port plug on the side of the base and install it in the cable port in the bottom of the base.
12. Install a conduit fitting onto the side of the base.
13. Place the base seal over the base, aligning the holes for the mounting screws in the base with those in the seal. Attach the
base and seal to the mounting surface with three screws.
14. Install a junction box with conduit close enough to the camera for the extension cable LAN and power connectors to be in
the box. When installing the junction box, attach the conduit to the fitting on the side of the camera base.
15. Route the extension cable Molex® connector end into the camera and re-attach it to the electronics.
16. Remove the protective cover on the camera lens.
2.4 Connections
Connections to the camera for audio in and out (microphone and speaker), D/I sensor, alarm, video out BNC, and RS-485 control are
made through the 11-pin terminal block.
11-pin terminal block
H.264 Indoor/Outdoor Dome IP Camera
5
SECTION 2: INSTALLATION AND SETUP
NOTE: When connecting leads from external devices
to the terminal block, use the pin definitions shown on
the circuit board as a guide. Pin definitions on the circuit
board may be different from those shown below.
Terminal block pin assignments
The 11-pin terminal block may be detached from the camera. Install the block in the location shown above.
2.4.1 Audio in/out connections
The camera includes an interface for a mono audio input (from a microphone) and a mono audio output (to a speaker). The audio
output is a low level signal that requires an amplified speaker (see Specifications). The configuration of the audio wiring (Aout, Ain)
is shown in the diagram below.
Audio in/out wiring schematic
To connect a speaker and/or microphone to the camera:
1.
Route speaker and/or microphone wiring through the cable channel and into the camera base housing.
2.
Strip 1/4” of insulation from the wires and insert them into the terminal block in the locations shown connector terminal
figure above. The common (ground) leads to the microphone and speaker share the same terminal block pin.
6
www.digiop.com
SECTION 2: INSTALLATION AND SETUP
2.4.2 Sensor in (DI) connection
The camera provides one channel for sensor input that can be connected to either a voltage type or relay type sensor. For voltage
type sensors, the camera allows a maximum input of 24 V DC, with a 1 V DC threshold (see Specifications). The configuration of the
sensor input wiring is illustrated in the diagrams below.

CAUTION
Do not exceed the maximum input voltage or the relay switching rate. Refer to the specifications in this
manual for more information.
Voltage type sensor wiring schematic
Relay type sensor wiring schematic
To connect a sensor to the camera:
1.
Route sensor wiring through the cable channel and into the camera base housing.
2.
Strip 1/4” of insulation from the sensor wires and insert them into the terminal block in the DI pin locations shown above.
The pin marked “C” in the terminal block is the common (COM) pin.
H.264 Indoor/Outdoor Dome IP Camera
7
SECTION 2: INSTALLATION AND SETUP
2.4.3 Alarm out (DO) connection
The camera supports one alarm out connection to relay type device. It provides up to 24 V AC @ 500 mA or 12 V DC @ 1 A. The
configuration of the relay type alarm wiring is illustrated in the diagram below.

CAUTION
Do not exceed the maximum relay rating. Refer to the specifications in this manual for more information.
Relay type alarm wiring schematic
To connect an alarm reporting device to the camera:
1.
Route alarm out wiring through the cable channel and into the camera base housing.
2.
Strip 1/4” of insulation from the wires and insert them into the terminal block in the DO pin locations shown above. The pin
marked “C” in the terminal block is the common (COM) pin.
2.4.4 RS-485 device connection
The camera provides one RS-485 interface connection. The wiring signal polarity to the terminal block is shown in the schematic
below.
RS-485 device wiring schematic
8
www.digiop.com
SECTION 2: INSTALLATION AND SETUP
To connect an RS-485 device wiring to the camera:
1.
Route RS-485 device wiring through the cable channel and into the camera base housing.
2.
Strip 1/4” of insulation from the wires and insert them into the terminal block. Observe the signal polarity shown in the
schematic.
2.4.5 Video out connection
The camera provides pins on the terminal block to attach a local video monitor. A cable extension with a BNC connector is included
in the packaging with the camera. When needed, attach the video cable to the terminal block as shown in figure below.
Local video cable connection
2.4.6 LAN and power connections
1.
Route a LAN drop cable into the camera and plug it into the LAN connector. If the camera is powered through the LAN cable,
DO NOT apply power to your camera at this time.
Power
connector
LAN
connector
H.264 Indoor/Outdoor Dome IP Camera
9
SECTION 2: INSTALLATION AND SETUP
2.
Route the wire end of the power extension cable into the camera and connect it to the 12 VDC power connector.
3.
Connect the other end of the power extension cable to the DC12V power adapter. The polarity of the adapter connector is
shown in the following diagram. DO NOT apply power to the camera at this time.

CAUTION
When applying power to the camera, ensure that the polarity is correct. An incorrect connection may cause a malfunction and
can damage the camera.
2.5 Install IPAdmin Tool
The IPAdmin Tool, included on the CD mini disk, is a utility that will discover cameras installed on your network and enable you
to perform the initial network setup for each camera. After a camera is setup on the network, the Microsoft Internet Explorer ®
web browser can be used to see video from the camera, set the camera’s password, date and time, finalize camera hardware
adjustments, and configure the camera for functional requirements.
The IPAdminTool can be loaded on a Microsoft Windows XP, Vista or Windows 7 operating system (32- or 64-bit). To use this utility
for the initial setup of your camera, your computer must be connected to the same network subnet as your camera.
At a computer on the same LAN (subnet) where your cameras will be installed, do the following:
1.
Insert the CD mini disk provided with your camera into your computer’s CD ROM drive and open the CD in a Windows
Explorer window.
2.
Find the IPAdminTool directory on the CD.
3.
Copy the IPAdminTool directory with its contents to your computer hard drive.
2.6 Configure the camera network settings
Devices attached to a Local Area Network (LAN) are each assigned a unique address (IP address) that they use when sending
messages with each other. No two devices on a single Ethernet network can have the same IP address. Otherwise, addressing
conflicts will occur.
10
www.digiop.com
SECTION 2: INSTALLATION AND SETUP
When your IP camera is attached to a network and initially powered on, it attempts acquire compatible network settings from
a DHCP server. If it cannot find a DHCP server, it configures itself with the following static IP address, subnet mask, and gateway
setting, which may or may not be compatible with other devices on the network.
IP address:
Subnet mask:
Gateway:
192.168.0.100
255.255.255.0
192.168.0.1
Whether it acquires a dynamic (changeable) IP address and other network settings from a DHCP server, or uses the default static
(fixed, unchanging) settings, your camera must be configured with static network settings that are compatible with the network
configuration. Additionally, if DHCP is not used on your network, DIGIOP Black cameras must be installed on the network and
configured with new network settings one at a time to avoid addressing conflicts.
Use the following procedure to setup and apply compatible, static, network settings for your camera. If connecting your camera to a
large enterprise network, consult with your network administrator for network settings before attaching the camera to the LAN to
ensure that your camera won’t conflict with other devices. Your network administrator should also setup WAN (Internet) access to
the camera, if that is needed.
If you encounter a problem and need to contact Technical Support, first complete the chart in Table 1 about your computer (PC) and
camera network settings, if possible. Support will need this information to provide assistance.
2.6.1 Configuring cameras on networks with DHCP
In networks with a DHCP server, the IP camera will acquire dynamic (changeable) network settings when it is initially powered on.
These dynamic settings can easily be converted to static settings, or changed to other static settings that are also compatible with
your network.
1.
Connect your camera to the LAN, then power on the camera.
2.
Open the IPAdminTool directory on your computer, then double click the file IPAdminTool.exe to start the application.
When the IPAdmin Tool starts, it will discover all the IP devices it supports that exist on the network. The discovery process
may take a few minutes.
H.264 Indoor/Outdoor Dome IP Camera
11
SECTION 2: INSTALLATION AND SETUP
Check the list of IP devices found by IPAdmin Tool. You can identify your camera by the MAC address. If the camera was not
found, click the Refresh button every minute until your camera appears in the list.
3.
In the IPAdmin Tool device list, use the camera’s MAC Address to find the camera you are installing. After finding the camera,
right click the entry, then select IP Address from the drop-down list. An IP Setup window will open.
4.
In the IP Setup window, click the Static option bullet to select this option.
Static
Option
12
www.digiop.com
SECTION 2: INSTALLATION AND SETUP
If you have other compatible, network settings you want to apply to the device, enter them in the appropriate locations. Click
Setup to save settings.
5.
In the Login window, enter the ID and PW (password) for your camera and click Login. The default administrator values for
the ID and PW are root and pass. After entering ID and PW, the IP Setup window closes.
6.
In the IPAdmin Tool window, click Refresh and verify that the entry representing the camera now shows the new IP address.
7.
Continue with procedure 2.7 Setup camera Basic Configuration.
2.6.2 Configuring cameras on networks without DHCP
NOTE
The following procedure works with most networks. For further assistance, contact Technical Support.
Cameras installed on a network without a DHCP server will initially use the factory default static network settings:
IP address:
Subnet mask:
Gateway:
192.168.0.100
255.255.255.0
192.168.0.1
In networks without a DHCP server, cameras must be powered on and reconfigured one at a time to avoid addressing conflicts
between other cameras, or possibly with another device on the network. Configuring the network settings of your cameras includes
these steps:
——
——
——
——
Determine the network settings of your computer.
Check the network for compatibility with the default static network settings of your camera.
Find network settings (IP addresses) that are not in use and can be assigned to your camera.
Attach your camera to the network, power it on, and configuring it with new network settings.
Determine the network settings of your computer
1.
At a PC attached to the same LAN that will be shared with your camera, determine the IP address, subnet mask, and default
gateway of your PC and record it in Table 1. To find this information, do the following at the Windows desktop:
a.
Hold down the Windows key and press r to open the Run dialog box.
Indoor/Outdoor Mini-Dome IP Camera
13
SECTION 2: INSTALLATION AND SETUP
b.
Type cmd in the entry field, then click OK to open the DOS command window.
c.
At the command prompt, enter ipconfig. The response will show the your PC’s network settings.
Example: Typical use of ipconfig in Windows XP
d.
Enter the IP Address, Subnet Mask, and Default Gateway for your PC’s Ethernet adapter into Table 1.
NOTE
The Ethernet adapter data you see by using ipconfig will probably be different from that shown in the example
above. If you are using Windows Vista or Windows 7, the IP address is identified as the “IPv4 Address.”
Table 1. PC/Camera network settings
Computer (PC)
Camera
IP Address
Subnet Mask
Default Gateway

CAUTION
14
If connecting your camera to an enterprise network, consult with your network administrator for the
camera IP address, subnet mask, and default gateway.
www.digiop.com
SECTION 2: INSTALLATION AND SETUP
Find network settings (IP addresses) that are not in use
1.
At your PC, find an IP address on your network that is not in use:
a.
Write down the EXACT IP address of your PC up to the third/last period. Using the example shown above, this
expression is: 192.168.1.
b.
After the third period, include any number between 1 and 254 that is different from the one in your PC’s IP address,
168. As a first try, let’s choose 200, which will form the IP address 192.168.1.200.
c.
Next, use the ping command in the DOS window to see if this IP address is in use on your network. The format of the
ping command is:
ping <IP address>
To test this IP address, enter ping 192.168.1.200. Any reply received from the ping indicates that a device on the
network is already using this IP address and you can connect to it.
In the example shown above, the message “Reply from 192.168.1.200: ..” indicates that your PC can reach the
device with that IP address, and that address is in use (i.e., you cannot use it for your camera).
d.
Since the ping test of the IP address we tried showed the address was in use, try another number between 1 and 254.
For example, let’s ping 192.168.1.201. At the DOS prompt, enter: ping 192.168.1.201
Indoor/Outdoor Mini-Dome IP Camera
15
SECTION 2: INSTALLATION AND SETUP
e.
In this test, the message “Request timed out” indicates that your PC cannot reach the device with that IP address, and
that address is probably not in use. Enter this number into Table 1. If this test indicated that this IP address is in use, try
other IP addresses using the steps above until an unused address is found.
Check LAN for default IP address compatibility
Because all DIGIOP Black cameras and encoders are factory configured with the static IP address 192.168.0.100, check the LAN
before connecting your camera to ensure that network conflicts won’t occur.
At a Microsoft Windows computer attached to the LAN subnet where the camera will be connected, open a Command Prompt
window and enter:
ping 192.168.0.100
The “Request timed out” response indicates that the IP address is not in use and the camera can be connected without causing
errors.
Attach your camera to the network and power it on
Apply power to the camera. When the camera powers on, it performs an internal initialization, then establishes a connection to the
LAN. Wait until the initialization process completes before continuing. It may take up to 3 minutes for your camera to initialize.
Configure the camera IP address
1.
16
Open the IPAdminTool directory on your computer, then double click the file IPAdminTool.exe to start the application.
When the IPAdmin Tool starts, it will discover all the IP devices it supports that exist on the network. The discovery process
may take a few minutes.
www.digiop.com
SECTION 2: INSTALLATION AND SETUP
2.
In the Product list, find the entry with the same MAC address as the camera you installed. If the camera is not shown, click
Refresh once a minute to update the list.
3.
Right click on the entry for your camera and select IP Address.
IP Setup window
4.
5.
In the IP Setup window:
a.
Select the Static option if it is not selected. This option is required if video from the camera will be recorded by a
network DVR, or if you want to view video from the camera across a WAN (Internet).
b.
Enter the IP address for your camera from Table 1 into the IP Address field.
c.
Enter the subnet mask for your computer from Table 1 into the Subnet Mask field.
d.
Click SETUP. A Login window will open.
In the Login window, enter the ID and PW (password) for your camera, then click Login. The default administrator ID and
PW are root and pass. After entering the ID and PW, the IP Setup window closes.
Indoor/Outdoor Mini-Dome IP Camera
17
SECTION 2: INSTALLATION AND SETUP
6.
In the IPAdmin Tool window, click Refresh and verify that the entry representing the camera now shows the new IP address.
7.
In the IPAdmin Tool window, click Refresh and verify that the entry for your camera now shows the new IP address.
2.7 Setup the camera Basic Configuration
IIn this procedure, use the Internet Explorer (IE) browser to setup the camera administrator and user passwords, date, and time.
1.
Open the IE browser.
2.
In the URL field (Internet address), enter the IP address for your camera in the format:
http://<IP address>/
where <IP address> is the IP address of your camera. Following the example earlier in this guide, the entry would be:
http://192.168.1.201
3.
If prompted to install an ActiveX control such as AxAll.cab (publisher Cap Co), follow screen prompts to install the software.
IE prompt to install ActiveX control
NOTE
18
To load these ActiveX controls, you may need to adjust the security settings of your browser to accept add-ins from
unknown publishers.
www.digiop.com
SECTION 2: INSTALLATION AND SETUP
Typical initial camera view
NOTE
If, after logging into your camera, you cannot see live video and the message:
“Can not Create XMLDOMDocument Install MSXML4.0” appears, download and install the MS XML 4.0 library. This library can
be found at:
http://www.microsoft.com/downloads/details.aspx?familyid=3144B72B-B4F2-46DA-B4B6-C5D7485F2B42&displaylang=en
4.
In the camera window, click the SETUP link in the upper right corner of the window. Enter the User name and Password for
the camera, and click OK. The default administrator values are root and pass. The Basic Configuration window will open.
5.
In the Basic Configuration menu, click Date & Time.
Indoor/Outdoor Mini-Dome IP Camera
19
SECTION 2: INSTALLATION AND SETUP
In the Date & Time Setting options:
6.
20
a.
Select the Time Zone you prefer.
b.
Select the synchronization method, or Set Manually bullet and enter the appropriate information.
c.
Select the Sync Source and Interval you prefer.
d.
Click Apply.
In the Basic Configuration menu, click Users.
www.digiop.com
SECTION 2: INSTALLATION AND SETUP
7.
In the User List, click root, and then click Modify and follow the prompts. Setup the administrator user with a new
password and click OK.
8.
In the Users menu, click Apply, then click OK to restart the webserver (if you wish to do so at this time).
9.
Click Add to include other administrators, operators or viewers to the user list. Follow the screen prompts to complete the
entries.
10. Click VIEW in the upper right corner of the window to return to the camera live view.
2.8 Aim, focus, and image quality adjustment
2.8.1 Aim
The camera mount allows the camera to be rotated on three axis to set the horizon alignment, horizontal direction, and up/down
position of the video frame.
Indoor/Outdoor Mini Dome IP Camera
21
SECTION 2: INSTALLATION AND SETUP
Horizon alignment
Horizontal direction
Up/down position
Lens shroud
1.
Gently lift the lens shroud off the camera assembly to remove it from the camera.
2.
While observing video from the camera, set the horizon alignment by rotating camera module bracket on its horizontal axis
(direction the lens is pointed).
3.
Set the horizontal direction of the video frame by rotating camera assembly on its vertical axis.
4.
Set the up-down position of the video frame by point the lens up or down.
5.
If necessary, make additional adjustments to these settings to perfect the frame of the video.
6.
Reinstall the lens shroud
7.
Reinstall the camera dome.
2.8.2 Focus
The lens focus is set at the factory and requires no further adjustment.

CAUTION
If a camera with a high zoom lens is subjected to a temperature variation of about 18˚F or more, a change of focus may
occur. Make sure to consider the environment when installing a camera with a high zoom lens.
2.8.3 Image quality adjustments
Adjustments to the image brightness, contrast, hue, saturation, and sharpness are performed through the web browser:
1.
22
From the VIEW window, click: SETUP > Video & Audio > Video-In
www.digiop.com
SECTION 2: INSTALLATION AND SETUP
2.
Scroll to the bottom of the screen and click the PREVIEW button. Follow the screen instructions to open the camera view in
another IE window.
3.
While observing the video in the PREVIEW window, adjust the values for brightness, contrast, hue, saturation, sharpness,
and/or other parameters on screen. Click Apply to see the effect of the change. Make any necessary adjustments to produce
the best video image.
4.
Close the PREVIEW window and click VIEW to return to the normal viewing window.
2.9 Speaker/microphone setup
Verify the functionality of the speaker and microphone setup at the camera, and adjust volume levels.
1.
Re-install the camera housing.
2.
On the VIEW screen, click: SETUP > Video & Audio > Audio
to open the Bi-directional Audio Settings menu.
H.264 Indoor/Outdoor Dome IP Camera
23
SECTION 2: INSTALLATION AND SETUP
3.
In the Bi-directional Audio Settings menu, click the check boxes to select “Listen to the audio from server with
setting below” and “Talk to the speakers of server”.
4.
Click Apply, and then click VIEW to return to the camera view screen.
5.
On the VIEW screen, check the SPK and MIC options to enable the speaker at the camera and the microphone on your
computer.
6.
At your computer, listen for sounds from the microphone at the camera. If necessary, adjust the volume level in the camera.
Click: SETUP > Video & Audio > Audio
to re-open the Bi-directional Audio Settings menu. In the Listen frame, adjust the volume to the preferred level. Click Apply.
7.
Use a microphone at your PC to send audio to the speaker at the camera. Verify that your microphone audio is heard at the
speaker.
To adjust the speaker volume go to the Bi-directional Audio Settings menu. In the Talk to frame, adjust the volume to an
appropriate level. Click Apply.
24
www.digiop.com
SECTION 2: INSTALLATION AND SETUP
2.10 Cleaning
Clean the camera housing with an approved glass cleaning solution and a lint free cloth.
•
•
Dust can be removed from the unit by wiping it with a soft damp cloth. To remove stains, gently rub the surface with a soft
cloth moistened with a mild detergent solution, then rinse and dry it with a soft cloth.
Remove all foreign particles, such as plastic or rubber materials, attached to the camera housing. These may cause damage
to the surface over time.

CAUTION
Do not use benzene, thinner or other chemical products on the camera assembly; these may dissolve the paint and
promote damage of the surfaces. Before using any chemical product, read the accompanying instructions carefully.
H.264 Indoor/Outdoor Dome IP Camera
25
SECTION 3: SPECIFICATIONS
SECTION 3
Specifications
Table 2.Specifications
Camera Module
CCD
Sync
ELECTRICAL
Image Sensor
SONY 1/3” Super HAD CCD
Effective Pixels
NTSC: 768(H) x 494(V); PAL: PAL: 752(H) x 582(V)
Size
1/3 inch interline transfer CCD
Scanning system
2:1 Interlace
Frequency
NTSC: 15.734 KHz (H) 59.94 Hz(V); PAL:15.625 KHz(H) 50.00 Hz (V)
Resolution
550 TV lines
S/N (Y signal)
52 dB (AGC Off, weight on)
Min. Illumination
0.00001 Lux F1.2 (Sens-Up * 258))
Wide Dynamic Range
52 dB (x128)
Color
ON/AUTO
AGC Control
OFF/LOW/MIDDLE/HIGH selectable
White Balance
ATW/AWB/INDOOR/OUTDOOR/MANUAL/AWC
Electronic Shutter Speed
1/60 ~ 1/100,00
Sense-Up
Auto/Fixed/Off (Selectable Limit*2 ~ 258)
DNR
On/Off (1~100 Level Selectable)
Lens
2.8~10.5 mm F1.2 DC Auto Iris Board Vari-Focal
Day & Night
IS/W Day & Night or IR Cut Filter (model dependent)
Video
Compression Format
H.264, MPEG-4, MJPEG selectable per stream
Number of Streams
Dual stream, configurable
Resolution
D1, 4CIF, VGA, CIF, QVGA, QCIF
Compression FPS
25/30 fps@D1 (PAL/NTSC)
Deinterlacing
Supported (DSP)
Motion Detection
Supported
Burnt-in Text (Digital)
Supported (DSP)
Output
1 Loop Out (BNC connector)
Audio
Input/output
1/1 channel
Compression Format
G.711
26
www.digiop.com
SECTION 3: SPECIFICATIONS
Function
Digital Input/output
1/1 channel
RS-485
Supported
Network
10/100Base-T
Power over Ethernet
Supported
Protocol
TCP/IP, UDP/IP, HTTP, RTSP, RTCP, RTP/UDP, RTP/TCP, SNTP, mDNS, UPnP, SMTP, SOCK, IGMP, DHCP, FTP,
DDNS, SSL v2/v3, IEEE 802.1X, SSH, SNMP v2/v3
SD Slot
Supported — MicroSD (MicroSD card not included)
Material
Aluminum Die Casting
Dimensions
Housing : 5.94”dia. x 4.45”h, Dome : 3.94”dia.
Color
White
Electrical characteristics
Video Output
1 Vp-p, 75Ω
Audio Input
Linein, 1.43 Vp-p (Min 1.35 Vp-p, max 1.49 Vp-p), 39 KΩ
Audio Output
Lineout, 46 mW Power, 16 Ω
Sensor(D/I)
TTL level 4.5V threshold, Max 50 mA
Alarm(D/O)
Max 500 mA@24 V AC or 1A @ 12 V DC
Power Source (approx)
12 V DC 300 mA or PoE IEEE 802.3af (Class 0)
Power Consumption (approx.)
4.2W (DC12V) / 5.62W (POE)
Environmental requirements
Operating Temperature
32˚F ~ 122˚F (0˚C ~ 50 ˚C)
Operating Humidity
Up to 85% RH
Mechanical characteristics
Material
Aluminum (die cast)
Color
White
Dimensions
Housing: 5.94” dia x 4.45”h (ø150.8 mm x 113 mm (h))
Dome: 3.94” dia. (ø100 mm)
Weight
2.38 lbs. (1,080g)
H.264 Indoor/Outdoor Dome IP Camera
27
SECTION 3: SPECIFICATIONS
Table 3.Video Content Analysis (optional)*
VCA Presence
High Performance
Advanced Tracking Algorithm, Low False Alarm Rate
Easy to Use
Intuitive Web Browser Interface
Detection Zones
Multi-segment Polygons and Lines
On-screen Display
Real-time Display of Tracking Data and Events
Burnt-in Annotation
Stream or Analog video out (Analog video out support can vary depending on the device model, hardware version, and the
firmware version)
Image Stabilization
Electronic Stabilization
Removes Camera Sway
*Other VCA options are available. Call for details.
28
www.digiop.com
APPENDIX A: TROUBLESHOOTING
APPENDIX A
Troubleshooting
A.1 Reboot camera
NOTE
The reboot process lasts about 2 minutes, during which time the camera will not respond to the IPAdmin Tool or transmit video to
a web browser
The camera can be rebooted in two ways:
•
•
Using the IPAdmin Tool:
a.
Start the IPAdmin Tool.
b.
Find the entry for the camera you want to reboot and click it to select (highlight) it.
c.
Click the Reboot button and enter the administrator ID and PW.
d.
Click Refresh to re-discover the camera.
Using the reset button on the camera:
a.
Press and hold the reset button on the camera for 5 seconds.
b.
Click Refresh to re-discover the camera.
A.2 Set camera to factory default network settings
The camera network settings can be forced to the factory default values:
Network settings acquired through DHCP on networks with DHCP
- OR Network settings forced to the following on networks were a DHCP server cannot be found:
——
——
——
——
——
IP address – reset to 192.168.0.100
Subnet mask – reset to 255.255.0.0
Gateway – reset to 192.168.0.1
User ID – reset to root
Password – reset to pass
H.264 Indoor/Outdoor Dome IP Camera
29
APPENDIX A: TROUBLESHOOTING
To force the camera to the factory network settings:
1.
Disconnect the power (adapter) from the camera.
2.
While pressing and holding down the reset button, power on the camera.
3.
Release the Reset button 5 seconds after applying power.
4.
Wait for the camera to reboot.
A.3 Checking your Firmware
Firmware is software embedded in the camera that determines many of its features and functionality. The current firmware version
number in your camera can be found by viewing video from the camera in IE, and then clicking SETUP > About > Version.
Contact DIGIOP Support for firmware updates.
A.4 Support
If you cannot resolve an issue, please contact the DIGIOP Support at 1.877.972.2522 for assistance. When you contact support,
please provide the server reports, log file and a brief description of the problem, if possible.
•
To generate server reports, enter the following into the IE address field:
https://<IP ADDRESS>/nvc-cgi/admin/param.cgi?action=list
- and https://<IP ADDRESS>/nvc-cgi/admin/vca.cgi?action=list
where <IP ADDRESS> is the IP address of your camera. The server report contains important information about the device,
as well as a list of the current parameters.
•
To generate a log report, use IE to log into the unit. In the View screen, click the following items, entering security
information when required:
SETUP > Maintenance > System Log > LOG LIST
Click the name of the Log List of interest to open it.
30
www.digiop.com
APPENDIX B: DIMENSIONS
APPENDIX B
Dimensions
5.94”
Top View
Ø 3.94”
4.47”
3/4” Tap
Side View
H.264 Indoor/Outdoor Dome IP Camera
31
APPENDIX B: DIMENSIONS
1.24”
3/4” Tap
Ø 4.53”
~ Ø .15”
Base view
32
www.digiop.com
APPENDIX C: POWER OVER ETHERNET
APPENDIX C
Power over Ethernet
The BLK-NewIPE3500L camera supports Power over Ethernet (PoE) in conformance with the IEEE 802.3af standard. IEEE 802.3af
allows for two power options for Category 5 cables.
The PoE module signature and control circuit provides the PoE compatibility signature and power classification required by
the Power Sourcing Equipment (PSE) before applying up to 15 W power to the port.
The high efficiency AC/DC converter operates over a wide input voltage range and provides a regulated low ripple and low
noise output. The AC/DC converter also has built-in overload and short-circuit output protection.
•
•
C.1 PoE compatibility
With non Power Sourcing Equipment (PSE)
When it is connected with non PSE, use the power adaptor to provide power to the camera.
With power adaptor
Connecting both PSE and power adaptor does not do any harm to the products. Disconnecting power adaptor while it is operating
does not stop operation. The product continues to work without rebooting.
C.2 Power classification
The PoE Power Class supported by the IP device is Class 0.
Class
Usage
Minimum Power Levels Output at the PSE
Maximum Power Levels at the Powered Device
0
Default
15.4 W
0.44 to 12.95 W
H.264 Indoor/Outdoor Dome IP Camera
33