HCD-F3MD
SERVICE MANUAL
E Model
HCD-F3MD is the Amplifier, CD player, MD
Deck and Tuner section in CMT-F3MD.
US and foreign patents licensed from Dolby
Laboratories.
Model Name Using Similar Mechanism
HCD-MD373
CD
CD Mechanism Type
CDM55A-5SBD32
Section
Base Unit Name
BU-5SBD32
Optical Pick-up Name
KSS-213BH/Z-NP
Model Name Using Similar Mechanism
HCD-MD373
MD
MD Mechanism Type
MDM-5GA
Section
Base Unit Name
MBU-5A
Optical Pick-up Name
KMS-260B/S1NP
SPECIFICATIONS
Amplifier section
Laser output
DIN power output (Rated):20 + 20 watts (6 ohms at 1 kHz,
DIN, 240 V)
18 + 18 watts (6 ohms at 1 kHz,
DIN, 220 V)
Continuous RMS power output (Reference):
25 + 25 watts (6 ohms at 1 kHz,
10% THD, 240 V)
23 + 23 watts (6 ohms at 1 kHz,
10% THD, 220 V)
Peak Music Power Output: 400 watts
Inputs
TAPE IN (phono jacks): voltage 250 mV, impedance
47 kilohms
Outputs
TAPE OUT (phono jacks): voltage 250 mV, impedance
1 kilohm
PHONES (stereo minijack):
accepts headphones of 8 ohms or
more.
SPEAKER:
accepts impedance of 6 to 16
ohms.
Frequency response
Max. 44.6 µW*
*This output is the value measured
at a distance of 200 mm from the
objective lens surface on the
Optical Pick-up Block with a
7 mm aperture.
2 Hz – 20 kHz
Laser output
Sampling frequency
Frequency response
MiniDisc digital audio system
Semiconductor laser (λ=780 nm)
Emission duration: continuous
Max. 44.6 µW*
*This output is the value measured
at a distance of 200 mm from the
objective lens surface on the
Optical Pick-up Block with a
7 mm aperture.
44.1 kHz
5 Hz – 20 kHz
Laser
Compact disc and digital audio
system
Semiconductor laser (λ=780 nm)
Emission duration: continuous
Aerial
531 – 1,602 kHz
(with the interval set at 9 kHz)
530 – 1,710 kHz
(with the interval set at 10 kHz)
AM loop aerial
External aerial terminals
450 kHz
General
Power requirements
110 – 120 V or 220 – 240 V
AC, 50/60 Hz
Power consumption
70 watts during normal operation
Approx. 3 watts in standby mode
(clock displayed)
Approx. 1 watt in standby mode
(clock not displayed)
Dimensions (w/h/d) incl. projecting parts and controls
Approx. 215 × 150 × 335 mm
Approx. 4.9 kg
Mass
Tuner section
FM stereo, FM/AM superheterodyne tuner
CD player section
System
Tuning range
Intermediate frequency
MD deck section
System
Laser
AM tuner section
Design and specifications are subject to change
without notice.
FM tuner section
Tuning range
Aerial
Aerial terminals
Intermediate frequency
87.5 – 108.0 MHz
(50 kHz step)
FM lead aerial
75 ohms unbalanced
10.7 MHz
COMPACT DISC DECK RECEIVER
SELF-DIAGNOSIS FUNCTION
The self-diagnosis function consists of error codes for customers, which are displayed automatically when errors occur, and error codes,
which show the error history in the test mode during servicing. For details on how to view error codes for the customer, refer to the
following box in the instruction manual. For details on how to check error codes during servicing, refer to the following “Procedure for
using the Self-Diagnosis Function (Error History Display Mode)”.
Self-diagnosis Display
This system has a Self-diagnosis display function
to let you know if there is a system malfunction.
The display shows a code made up of three letters
and a message alternately to show you the
problem. To solve the problem refer to the
following list. If any problem persists, consult
your nearest Sony dealer.
C13/REC Error
Recording could not be performed properly.
cMove the system to a stable place, and start
recording over from the beginning.
The MD is dirty or scratched, or the MD does
not meet the standards.
cReplace the MD and start recording over from
the beginning.
C13/Read Error
The MD deck cannot read the disc information
properly.
cRemove the MD once, then insert it again.
C14/Toc Error
The MD deck cannot read the disc information
properly.
cReplace the MD.
cErase all the recorded contents of the MD
using the All Erase function on page 38.
C11/Protected
The MD is protected against erasure.
cRemove the MD and slide the tab to close the
slot (see page 24).
C12/Cannot Copy
You tried to record a CD or MD with a format
that the system does not support, such as a CDROM.
cRemove the disc and turn off the system once,
then turn it on again.
C41/Cannot Copy
The sound source is a copy of a commercially
available music software, or you tried to record
a CD-R (Recordable CD).
cThe Serial Copy Management System
prevents making a digital copy (see page 53).
You cannot record a CD-R.
PROCEDURE FOR USING THE SELF-DIAGNOSIS FUNCTION (ERROR HISTORY DISPLAY MODE)
Note 1: About “R”
As this unit has only a few buttons, some operations require the use of remote commander (RM-SF3MD/provided with unit: 1-476-068-11)
buttons. These operations are indicated as “R” in this manual.
Example: MENU/NO “R” ...Press the [MENU/NO] button of the remote commander.
Note 2: Incorrect operations may be performed if the MD test mode is not entered properly.
In this case, press the I/1 button to turn the power off, and retry to enter the MD test mode.
Note 3: Perform the self-diagnosis function in the “error history display mode” in the MD test mode. The following describes the least required
procedure. Be careful not to enter other modes by mistake. If you set other modes accidentally, press the MENU/NO “R” button to exit the
mode.
Procedure:
1. Press the I/1 button to turn the power on.
2. Press the [FUNCTION] button to set the MD function.
3. Press three buttons of s (MD) , zREC and I/1 simultaneously to enter the MD test mode and display “[Check]”.
4. Press the l m or M L button to display “[Service]”, and press the ENTER/YES “R” button.
5. Press the l m or M L button to display “ERR DP MODE”.
6. Press the ENTER/YES “R” button to enter the error history mode and display “total rec”.
7. Select the contents to be displayed or executed using the l m or M L button.
8. Press the [CD-MD SYNC] button will display or execute the contents selected.
9. Press the [CD-MD SYNC] button another time returns to step 7.
10. Press the MENU/NO “R” button displays “ERR DP MODE” and release the error history mode.
11. To release the MD test mode, press the [REPEAT] button to display “Initialize” and release the MD test mode.
2
ITEMS OF ERROR HISTORY MODE ITEMS AND CONTENTS
Selecting the Test Mode
Display
Details of History
total rec
Displays the recording time.
Displayed as “rssssssh”.
The displayed time is the total time the laser is set to the high power state.
This is about 1/4 of the actual recording time.
The time is displayed in decimal digits from 0h to 65535h.
total play
Displays the play time.
Displayed as “pssssssh”. The time displayed is the total actual play time. Pauses are not counted.
The time is displayed in decimal digits from 0h to 65535h.
retry err
Displays the total number of retries during recording and number of retry errors during play.
Displayed as “rss pss”.
“r” indicates the retries during recording while “p” indicates the retry errors during play.
The number of retries and retry errors are displayed in hexadecimal digits from 00 to FF.
total err
Displays the total number of errors.
Displayed as “total ss”.
The number of errors is displayed in hexadecimal digits from 00 to FF.
err history
Displays the 10 latest errors.
Displayed as “0s E@@”.
s indicates the history number. The smaller the number, the more recent is the error. (00 is the latest).
@@ indicates the error code.
Refer to the following table for the details. The error history can be switched by pressing the l m or
M L button.
er refresh
Mode which erases the “retry err”, “total err”, and “err history” histories.
When returning the unit to the customer after completing repairs, perform this to erase the past error history.
After pressing the [CD-MD SYNC] button and “er refresh?” is displayed, press the ENTER/YES “R” button to
erase the history.
“Complete!” will be displayed momentarily.
Be sure to check the following when this mode has been executed.
• The data has been erased.
• The mechanism operates normally when recording and play are performed.
tm refresh
Mode which erases the “total rec” and “total play” histories.
These histories serve as approximate indications of when to replace the optical pick-up.
If the optical pickup has been replaced, perform this operation and erase the history.
After pressing the [CD-MD SYNC] button and “tm refresh?” is displayed, press the ENTER/YES “R” button to
erase the history.
“Complete!” will be displayed momentarily.
Be sure to check the following when this mode has been executed.
• The data has been erased.
• The mechanism operates normally when recording and play are performed.
Table of Error Codes
Error Code
E00
E01
E02
Details of Error
No error
Error Code
E05
Details of Error
FOK has deviated
Disc error. PTOC cannot be read
E06
Cannot focus (Servo has deviated)
(DISC ejected)
E07
Recording retry
Disc error. UTOC error
E08
Recording retry error
(DISC not ejected)
E09
Playback retry error
E03
Loading error
E04
Address cannot be read (Servo has deviated)
(Access error)
E0A
Playback retry error (C2 error)
3
TABLE OF CONTENTS
SELF-DIAGNOSIS FUNCTION ..................................... 2
1.
SERVICING NOTES ............................................... 5
2.
GENERAL ................................................................... 16
3.
DISASSEMBLY ......................................................... 18
4.
TEST MODE ............................................................... 26
5.
ELECTRICAL ADJUSTMENTS
MD Section ..................................................................... 30
CD Section ...................................................................... 38
6.
DIAGRAMS
6-1.
6-2.
6-3.
6-4.
6-5.
6-6.
6-7.
6-8.
6-9.
6-10.
6-11.
6-12.
6-13.
6-14.
6-15.
6-16.
6-17.
6-18.
6-19.
6-20.
6-21.
6-22.
6-23.
6-24.
6-25.
6-26.
6-27.
Block Diagram – CD SERVO Section – .......................
Block Diagram – MD SERVO Section (1/2) – .............
Block Diagram – MD SERVO Section (2/2) – .............
Block Diagram – MAIN Section – ................................
Note for Printed Wiring Boards and
Schematic Diagrams .......................................................
Printed Wiring Board – BD (CD) Board – ....................
Schematic Diagram – BD (CD) Board – .......................
Schematic Diagram – BD (MD) Board (1/2) – .............
Schematic Diagram – BD (MD) Board (2/2) – .............
Printed Wiring Board – BD (MD) Board – ...................
Schematic Diagram – BD SW (MD) Board – ...............
Printed Wiring Board – BD SW (MD) Board – ............
Schematic Diagram – LOADING (CD) Board – ..........
Printed Wiring Board – LOADING (CD) Board – .......
Printed Wiring Board – MD DIGITAL Board – ...........
Schematic Diagram – MD DIGITAL Board – ..............
Printed Wiring Board – MAIN Board – ........................
Schematic Diagram – MAIN Board (1/3) – ..................
Schematic Diagram – MAIN Board (2/3) – ..................
Schematic Diagram – MAIN Board (3/3) – ..................
Printed Wiring Boards – AMP/SP Boards – ..................
Schematic Diagram – AMP/SP Boards – ......................
Printed Wiring Board – PANEL Board – ......................
Schematic Diagram – PANEL Board – ........................
Printed Wiring Board – POWER Board – .....................
Schematic Diagram – POWER Board – ........................
IC Pin Function Description ...........................................
7.
EXPLODED VIEWS ................................................ 80
8.
ELECTRICAL PARTS LIST ............................... 86
39
40
41
42
43
44
45
46
47
48
49
49
49
49
50
51
52
53
54
55
56
57
58
59
60
61
70
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be damaged by heat.
Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270 ˚C during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous radiation exposure.
This appliance is classified as a CLASS 1 LASER product.
The CLASS 1 LASER PRODUCT MARKING is located on
the rear exterior.
Laser component in this product is capable of emitting radiation
exceeding the limit for Class 1.
The following caution label is located inside the unit.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED
LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS
AND IN THE PARTS LIST ARE CRITICAL TO SAFE
OPERATION. REPLACE THESE COMPONENTS WITH
SONY PARTS WHOSE PART NUMBERS APPEAR AS
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
4
SECTION 1
SERVICING NOTES
NOTES ON HANDLING THE OPTICAL PICK-UP
BLOCK OR BASE UNIT
MODEL IDENTIFICATION
— Back panel —
The laser diode in the optical pick-up block may suffer electrostatic break-down because of the potential difference generated
by the charged electrostatic load, etc. on clothing and the human
body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
PART No.
For CD
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused
on the disc reflective surface by the objective lens in the optical
pick-up block. Therefore, when checking the laser diode emission, observe from more than 30 cm away from the objective lens.
LASER DIODE AND FOCUS SEARCH OPERATION
CHECK
Carry out the “S curve check” in “CD section adjustment” and
check that the S curve waveforms is output three times.
Model
Hong Kong model
Part No.
Korean model
4-229-548-1[]
4-232-128-0[]
Taiwan model
4-232-129-0[]
For MD
NOTES ON LASER DIODE EMISSION CHECK
Never look into the laser diode emission from right above when
checking it for adjustment. It is feared that you will lose your sight.
CLEANING OBJECTIVE LENS OF OPTICAL PICK-UP
• In cleaning the objective lens of optical pick-up, be sure the
following below.
1. In cleaning the lens, do not apply an excessive force.
As the optical pick-up is vulnerable, application of excessive
force could damage the lens holder.
2. In cleaning, do not use a cleaner other than exclusive cleaning
liquid (KK-91 or isopropyl alcohol).
3. Wipe the objective lens spirally from center toward outside.
(See Figure A)
(Figure A)
4. Eject the disk, if loaded.
5. Disconnect the power cord from the socket to shut off the power
supply.
6. When cleaning the objective lens of optical pick-up in CD,
refer to “HOLDER (BU) ASS’Y” on page 24 for removing
HOLDER (BU) ASS’Y.
5
DRAWING OUT THE TRAY WHEN THE POWER IS OFF
tray (CDM)
A
Move the cam block in the direction
of arrow A with a finger.
CLEANING THE OPTICAL PICK-UP (CD PLAYER)
CD mechanism deck
floating screw
(PTPWH M2.6)
optical pick-up block
Clean the lens block
with a cotton bud.
6
SERVICE POSITION OF THE MD MECHANISM
DECK
SERVICE POSITION OF THE CD MECHANISM
DECK
MD mechanism deck
CD mechanism deck
SERVICE POSITION OF THE POWER BOARD
POWER board
CN993
AMP board
CN802
MAIN board
Extension cable (4P)
(J-2501-042-A)
Extension cable (3P)
(J-2501-045-A)
7
MC COLD RESET
• The cold reset clears all data including preset data stored in the RAM to initial conditions. Execute this mode when returning the set to
the customer.
Procedure:
1. Press the I/1 button to turn the power on.
2. While pressing the [PLAY MODE/TUNING MODE] and s (CD) buttons, press the I/1 button.
3. The set is reset, and displays “COLD RESET”, then becomes standby status.
MC HOT RESET
• This mode resets the set with the preset data kept stored in the memory. The hot reset mode function is same as if the power cord is plugged
in and out.
Procedure:
1. Press the I/1 button to turn the power on.
2. While pressing the [PLAY MODE/TUNING MODE] and HS (CD) buttons, press the I/1 button.
3. The set is reset, and becomes standby state.
LED/FLUORESCENT INDICATOR TUBE AND KEY TEST
Procedure:
1. Press the I/1 button to turn the power on.
2. While pressing the [PLAY MODE/TUNING MODE] and A (CD) buttons, press the I/1 button.
3. LEDs and fluorescent indicator tube are all turned on.
4. Press the HS (MD) button to enter the key test mode, and display “Key0 Vol0”.
5. Each time a button is pressed, “Key” value increases. However, once a button is pressed, it is no longer taken into account.
“Vol” value increases like 0, 1, 2 ... if turn the [VOLUME] knob clockwise, or it decreases like 9, 8, 7 ... if turn the [VOLUME] knob
counterclockwise.
6. To release from this mode, press three buttons in the same manner as step 2, or disconnect the power cord.
Note: l m and M L buttons are no longer taken into account, if it pressed within for a second.
CHANGE-OVER THE AM TUNING INTERVAL
• The AM tuning interval can be changed over 9 kHz or 10 kHz.
Procedure:
1. Press the I/1 button to turn the power on.
2. Press the [FUNCTION] button to set the TUNER function, and press the [TUNER/BAND] button to select the band “AM”.
3. Press the I/1 button to turn the power off.
4. When the power off, press the I/1 button while pressing the [PLAY MODE/TUNING MODE] button, and the display of fluorescent
indicator tube changes to “AM 9k STEP” or “AM 10k STEP”, and thus the tuning interval is changed over.
8
MD SECTION
JIG FOR CHECKING BD (MD) BOARD WAVEFORM
The special jig (J-2501-149-A) is useful for checking the waveform of the BD (MD) board. The names of terminals and the checking items
to be performed are shown as follows.
GND : Ground
I+3V : For measuring IOP (Check the deterioration of the optical pick-up laser)
IOP : For measuring IOP (Check the deterioration of the optical pick-up laser)
TEO : Tracking error signal (Traverse adjustment)
VC : Reference level for checking the signal
RF : RF signal (Check jitter)
Mechanism deck
CN110
6P connector
5P connector
RF
VC
TEO
IOP
I+3V
GND
RF
VC
1 RF
VC
for
TEO MDM-3
IOP
5 I+3V
TEO
IOP
I+3V
GND
1 VC
RF
TEO for
IOP MDM-5
I+3V
6 GND
9
Note : About “R”
As this unit has only a few buttons, some operations require the use of remote commander (RM-SF3MD/provided with unit: 1-476-068-11)
buttons. These operations are indicated as “R” in this manual.
Example: MENU/NO “R” ...Press the [MENU/NO] button of the remote commander.
IOP DATA RECORDING AND DISPLAY WHEN OPTICAL PICK-UP AND NON-VOLATILE MEMORY (IC171 ON THE BD
(MD) BOARD) ARE REPLACED
The IOP value labeled on the optical pick-up can be recorded in the non-volatile memory. By recording the value, it will eliminate the need
to look at the value on the label of the optical pick-up. When replacing the optical pick-up or non-volatile memory (IC171 on the BD (MD)
board), record the IOP value on the optical pick-up according to the following procedure.
Record Procedure:
1. Press the I/1 button to turn the power on.
2. Press the [FUNCTION] button to set the MD function.
3. While pressing the s (MD) and zREC buttons, press the I/1 button to enter the MD test mode and display “[Check]”.
4. Press the l m or M L button to display “[Service]”, and press the ENTER/YES “R” button.
5. Press the l m or M L button to display “Iop Write”, and press the ENTER/YES “R” button.
6. The display becomes “Ref=@@@.@” (@ is an arbitrary number) and the numbers which can be changed will blink.
7. Input the IOP value written on the optical pick-up.
To select the number : Press the l m or M L button.
To select the digit
: Press the [SYNC REC] button.
8. When the ENTER/YES “R” button is pressed, the display becomes “Measu=@@@.@” (@ is an arbitrary number).
9. As the adjustment results are recorded for the step7 value. Leave it as it is and press the ENTER/YES “R” button.
10. “Complete!” will be displayed momentarily. The value will be recorded in the non-volatile memory and the display will become “Iop
Write”.
11. Press the [REPEAT] button to complete. “Standby” will be displayed.
Display Procedure:
1. Press the I/1 button to turn the power on.
2. Press the [FUNCTION] button to set the MD function.
3. While pressing the s (MD) and zREC buttons, press the I/1 button to enter the MD test mode and display “[Check]”.
4. Press the l m or M L button to display “[Service]”, and press the ENTER/YES “R” button.
5. Press the l m or M L button to display “Iop Read”, and press the ENTER/YES “R” button.
6. “@@.@/##.#” is displayed and the recorded contents are displayed.
@@.@ : indicates the Iop value labeled on the pick-up.
##.# : indicates the Iop value after adjustment
7. To release, press the [CD-MD SYNC] button or MENU/NO “R” button to display “Iop Read”. Then press the [REPEAT] button to
display “Standby”.
10
CHECKS PRIOR TO PARTS REPLACEMENT AND ADJUSTMENTS
Before performing repairs, perform the following checks to determine the faulty locations up to a certain extent.
Details of the procedures are described in “5 Electrical Adjustments”.
Criteria for Determination
(Unsatisfactory if specified value is not satisfied)
Measure if unsatisfactory:
• 0.9 mW power
Specified value : 0.84 to 0.92 mW
• 7.0 mW power
Specified value : 6.8 to 7.2 mW
• Clean the optical pick-up
• Adjust again
• Replace the optical pick-up
lop (at 7mW)
• Labeled on the optical pickup
Iop value ± 10mA
• Replace the optical pick-up
Traverse check
(5-6-3 : See page 32)
• Traverse waveform
Specified value : Below 10% offset
• Replace the optical pick-up
Focus bias check
(5-6-4 : See page 33)
• Error rate check
Specified value : For points A, B
C1 error : About 200
AD error : Below 2
For point C
C1 error : Below 50
AD error : Below 2
• Replace the optical pick-up
C PLAY check
(5-6-5 : See page 33)
• Error rate check
Specified value:
a. When using test disc (MDW-74/AU-1)
C1 error : Below 80
AD error : Below 2
b. When using check disc (TDYS-1)
C1 error : Below 50
• Replace the optical pick-up
Self-recording/playback
check
(5-6-6 : See page 33)
• CPLAY error rate check
Specified value:
C1 error : Below 80
AD error : Below 2
If always unsatisfactory:
• Replace the overwrite head
• Check for disconnection of the circuits around the
overwrite head
Laser power check
(5-6-2 : See page 32)
If occasionally unsatisfactory:
• Check if the overwrite head is distorted
• Check the mechanism around the sled
Temperature
compensation
offset check
(5-6-1 : See page 32)
• Unsatisfactory if displayed as T=@@ (##) [NG”
NG
(@@, ## are both arbitrary numbers)
• Check for disconnection of the circuits around
D101 (BD (MD) board)
• Check the signals around IC101, IC121, CN102,
CN103 (BD (MD) board)
Note:
The criteria for determination above is intended merely to determine if satisfactory or not, and does not serve as the specified value for adjustments.
When performing adjustments, use the specified values for adjustments.
11
RETRY CAUSE DISPLAY MODE
• In this test mode, the causes for retry of the unit during recording can be displayed on the fluorescent indicator tube. During playback,
the “track mode” for obtaining track information will be set.
This is useful for locating the faulty part of the unit.
• The following will be displayed :
During recording and stop : Retry cause, number of retries, and number of retry errors.
During playback
: Information such as type of disc played, part played, copyright.
These are displayed in hexadecimal.
Procedure:
1. Load a recordable disc whose contents can be erased into the unit.
2. Press the MENU/NO “R” button. When “Edit Menu” is displayed on the fluorescent indicator tube, press the l m or M L
button to display “All Erase?”.
3. Press the ENTER/YES “R” button.
4. When “All Erase??” is displayed on the fluorescent indicator tube, the music calendar number blinks.
5. Press the ENTER/YES “R” button to display “Complete!!”, and press the s (MD) button immediately. Wait for about 10 seconds
while pressing the button.
6. When the “TOC” displayed on the fluorescent display tube goes off, release the s (MD) button.
7. Press the zREC button to start recording. Then press the HS (MD) button and start recording. If recording cannot be performed,
press the [FUNCTION] button and set a different function.
8. To check the “track mode”, press the HS (MD) button to start play.
9. To release the test mode, press the I/1 button, and turn the power off. When “TOC” disappears, disconnect the power plug from the
outlet. If the test mode cannot be released, refer to “MC COLD RESET” on page 8).
Fig. 1 Reading the Test Mode Display
(During recording and stop)
Fig. 2 Reading the Test Mode Display
(During playback)
RTs@@c##e**
Fluorescent indicator tube display
@@ ###** $$
Fluorescent indicator tube display
@@ :
## :
** :
$$ :
@@ : Cause of retry
## : Number of retries
** : Number of retry errors
Parts No. (name of area named on TOC)
Cluster 
 Address
Sector 
Track mode (Track information such as copyright information of each part)
Reading the Retry Cause Display
Higher Bits
Hexa1 decimal
b7 b6 b5 b4 b3 b2 b1 b0
Hexadecimal 8
Bit
Binary
Lower Bits
Occurring conditions
Cause of Retry
4
2
1
8
4
2
0
0
0
0
0
0
0
1
01
shock
When track jump (shock) is detected
0
0
0
0
0
0
1
0
02
ader5
When ADER was counted more than five times
continuously
0
0
0
0
0
1
0
0
04
0
0
0
0
1
0
0
0
08
Discontinuous address When ADIP address is not continuous
When DIN unlock is detected
DIN unlock
0
0
0
1
0
0
0
0
10
FCS incorrect
When not in focus
0
0
1
0
0
0
0
0
20
IVR rec error
When ABCD signal level exceeds the specified range
0
1
0
0
0
0
0
0
40
CLV unlock
When CLV is unlocked
1
0
0
0
0
0
0
0
80
Access fault
When access operation is not performed normally
Reading the Display:
Convert the hexadecimal display into binary display. If more than two causes, they will be added.
Example
When 42 is displayed:
Higher bit: 4 = 0100 t b6
Lower bit : 2 = 0010 t b1
In this case, the retry cause is combined of “CLV unlock” and “ader5”.
When A2 is displayed:
Higher bit: A = 1010 t b7+b5
Lower bit : 2 = 0010 t b1
The retry cause in this case is combined of “access fault”, “IVR rec error”, and “ader5”.
12
Reading the Retry Cause Display
Higher Bits Lower Bits
HexaHexadecimal 8 4 2 1 8 4 2 1 decimal
Bit
b7 b6 b5 b4 b3 b2 b1 b0
Binary
Details
When 1
When 0
0
0
0
0
0
0
0
1
01
Emphasis OFF
Emphasis ON
0
0
0
0
0
0
1
0
02
Monaural
Stereo
0
0
0
0
0
1
0
0
04
0
0
0
0
1
0
0
0
08
This is 2-bit display. Normally 01.
01:Normal audio. Others:Invalid
0
0
0
1
0
0
0
0
10
Audio (Normal)
Invalid
0
0
1
0
0
0
0
0
20
Original
Digital copy
0
1
0
0
0
0
0
0
40
Copyright
No copyright
1
0
0
0
0
0
0
0
80
Write prohibited
Write allowed
Reading the Display:
Convert the hexadecimal display into binary display. If more than two causes, they will be added.
Example When 84 is displayed:
Higher bit: 8 = 1000 t b7
Lower bit : 4 = 0100 t b2
In this case, as b2 and b7 are 1 and others are 0, it can be determined that the retry cause is combined of “emphasis OFF”, “monaural”,
“original”, “copyright exists”, and “write allowed”.
Example When 07 is displayed:
Higher bit: 0 = 0000 t All 0
Lower bit : 7 = 0111 t b0+b1+b2
In this case, as b0, b1, and b2 are 1 and others are 0, it can be determined that the retry cause is combined of “emphasis ON”, “stereo”,
“original”, “copyright exists”, and “write prohibited”.
Hexadecimal t Binary Conversion Table
Hexadecimal
Binary
Hexadecimal
Binary
0
0000
8
1000
1
0001
9
1001
2
0010
A
1010
3
0011
B
1011
4
0100
C
1100
5
0101
D
1101
6
0110
E
1110
7
0111
F
1111
13
CD SECTION
CD TEXT DISPLAY
• This unit displays CD text.
Text is displayed for the first 50 tracks only and will not be displayed from the 51st track onwards. Do not suspect a fault in this case.
In some cases, some special characters will not be displayed and may be replaced by other characters. Do not suspect a fault in this case.
AGING MODE
• Mode for repeating operations of the CD player automatically.
When errors occur:
Aging stops and a message indicating that an error has occurred such as “CD MEC ERR” is displayed.
(For details of errors, refer to “Error History Display Mode”)
When no errors occur:
Aging is repeatedly performed.
Procedure:
1. Load any CD disc.
2. Press the [FUNCTION] button to set the CD function.
3. While pressing the [PLAY MODE/TUNING MODE] and HS (MD) buttons, press the I/1 button.
4. “AGING” is displayed on the fluorescent display tube briefly.
5. When the aging mode is set, it starts aging automatically.
6. Operations are performed in the following sequence during aging.
Aging mode sequence:
TOC read
Playback track 1
Playback last track
CD disc tray open
CD disc tray open
7. To release from this mode, while pressing the [PLAY MODE/TUNING MODE] and HS (CD) buttons, press the I/1 button.
(Hot reset is executed)
Error History Display Mode
Mode for checking the history of errors which have occurred in the CD player.
Execute this mode after ending the aging mode.
Procedure:
1. Press the [FUNCTION] button to set the CD function.
2. While pressing the M L and s (MD) buttons, press the I/1 button.
3. “EMC@@EDC**” is displayed.
@@ : Number of mechanism errors (Past 3 errors)
** : Number of errors (NO DISC ERROR) which occurred after chucking (Past 3 errors)
4. To check the history of mechanism errors, press the [PLAY MODE/TUNING MODE] button, and to check BD errors, press the
[REPEAT] button, and switch the display.
5. To release, press the I/1 button and turn the power off.
6. To erase the error history, perform COLD reset.
(While pressing the [PLAY MODE/TUNING MODE] and s (CD) buttons, press the I/1 button)
14
• Reading the Mechanism Error History Display
(To switch the history, press the [PLAY MODE/TUNING MODE] button)
Display
E@@M**#*$*
@@ : Error number. 00 is the latest
* : Invalid
#
: Load in operations related
D : Operations stopped due to problems other than mechanism related during CLOSE
E : Operations stopped due to problems other than mechanism related during OPEN
C : Operations stopped due to problems other than mechanism related during chucking up
$
: Load out operations related
1 : Operations stopped during chucking up
2 : Operations stopped during chucking down
• Reading the BD Error History Display
(To switch the history, press the [REPEAT] button)
Display
E@@D##$$%*
@@ : Error number. 00 is the latest
##
: Error details
01 : Focus error
02 : GFS error
03 : Setup error
$$
: Retry performed/not performed
00 : Determined as NO DISC without chucking retry
02 : Determined as NO DISC after chucking retry
%
: State when determined as NO DISC
1 : When stopped
2 : During setup
3 : During TOC READ
4 : During access
5 : During playback
6 : During PAUSE
7 : During manual search (during playback)
8 : During manual search (during pause)
:
Invalid
*
15
SECTION 2
GENERAL
This section is extracted from
instruction manual.
LOCATION OF CONTROLS
• Front View
1 I/1 button and indicator
2 MD disc slot
3 MD A button and MD disc indicator
4 MD H S button and indicator
5 MD s button
6 CD disc tray
7 CD A button and CD disc indicator
8 CD H S button and indicator
9 CD s button
0 Fluorescent indicator tube
qa Remote sensor
qs TUNER/BAND button
qd VOLUME knob
qf FUNCTION button
qg PHONES jack
qh PLAY MODE, TUNING MODE button
qj REPEAT, STEREO/MONO button
qk CD-MD SYNC button
ql zREC button and indicator
w; MD/CD l m/M L, TUNUNG +/– buttons
• Rear View
1 TAPE IN/OUT jacks
2 SPEAKER IMPEDANCE 6-16 Ω terminals
3 AM ANTENNA terminals
4 TAPE CONTROL jack
5 FM 75 Ω COAXIAL jack
6 AC power cord
16
3 N (play) button
Parts descriptions for
the remote
9 DBFB button
X (pause) button
5
6
x (stop) button
Press to label a CD, MD and preset station, or to
set the clock. (pages 5, 18, 35, 45)
Press to display the disc title or track title
scrolling. (pages 19, 23, 36)
qa CLEAR button
Note
./> (AMS: Automatic Music
You cannot perform the following operations with the
remote;
— TUNING MODE setting for the tuner
— STEREO/MONO setting for the tuner
— Removing discs
— Recording on the MD
— One Touch Play
Press to reinforce the bass sound. (page 44)
0 SCROLL button
9
CURSORT/t, m/M buttons
You can use the supplied remote to control the
system.
8
0
Sensor) buttons
7
4 VOL +/– buttons
Press to cancel the selection. (pages 16, 18, 21,
35, 45)
qa
Press to adjust the volume.
MENU/NO button
Press to set Programme Play, or to label a CD,
MD and preset station.
1
ENTER/YES button
2
Press to set the clock, Programme Play and to
label a CD, MD and preset station, or to enter the
settings in “Edit Menu” or “Setup Menu”.
DISP button
Press to show the various information. (pages 17
and 23)
3
5 SLEEP button
Press to set Sleep Timer. (page 46)
6 PLAY MODE button
Press to select normal play, Shuffle Play or
Programme Play. (pages 15, 16, 21, 25)
REPEAT button
Press to play a track or all the tracks repeatedly
(pages 15 and 20).
MUSIC MENU button
Press to select the type of the preset equalizer.
(page 44)
4
7 NAME EDIT buttons
Press to display the text input screen and to select
the type of characters to be input. (pages 19, 35,
45)
2 The sound source buttons
SPACE button
MD button
CD button
TAPE button
FUNCTION button
Press to switch the sound source.
Each time you press this button, the sound source
changes as follows;
t CD
t TUNER
TAPE T
Press to enter a space directly when labelling a
CD, MD and preset stion. (pages 19, 36, 46)
8 CLOCK/TIMER SELECT button
Additional Information
CHARACTER button
1 ?/1 (power) switch
Press to check timer settings, or to set the timer
on/off. (pages 48 and 49)
CLOCK/TIMER SET button
Press to set the clock and timer functions. (pages
5, 47, 48)
MD T
TUNER/BAND button
Press to select the tuner for the sound source, or
to select the FM or AM band.
60
61
Step 2: Setting the time
(continued)
Step 2: Setting the time
1
2
3,5
CURSORT
DISP
Getting Started
You must set the time beforehand to use the timer
functions.
5
Press . or > to set the minute.
6
Press ENTER/YES.
The clock starts.
If you made a mistake
Press CURSORT or t repeatedly until the
incorrect item flashes, then set it again.
3,5
4
4,6
To change the preset time
You can change the preset time while the system
is off.
1 Press DISP to display the clock.
2 Press CLOCK/TIMER SET.
3 Repeat steps 3 to 6 of “Setting the time”.
Tip
1
Turn on the system.
2
Press CLOCK/TIMER SET.
The upper dot of the colon flashes for the first 30
seconds, and the lower dot flashes for the last 30
seconds of each minute.
The clock appears and the hour indication
flashes.
3
4
Press . or > to set the hour.
Press ENTER/YES or CURSORt .
The minute indication flashes.
continued
5
6
17
SECTION 3
DISASSEMBLY
Note: Follow the disassembly procedure in the numerical order given.
CASE
2 case
1 two screws
(case3 TP2)
1 two screws
(case3 TP2)
FRONT PANEL SECTION
3 Remove the cord.
5 screw (BVTT3 × 6)
9 MD mechanism deck section
8 screw
(BVTP2.6 × 8)
8 screw (BVTP2.6 × 8)
1 wire (flat type) (25 core)
(CN107)
6 claw
BACK PANEL ASS’Y
(Page 22)
2 ground wire
7
q; front panel section
4 three screws
(BVTT3 × 6)
6 claw
1 wire (flat type)
(29 core) (CN11)
18
6 claw
MD MECHANISM DECK (MDM-5GA)
2 four step screws
(BVTPWH M3)
1 connector (CN601)
6 MD mechanism deck
(MDM-5GA)
4 wire (flat type) (23 core)
(CN103)
4 wire (flat type) (21 core)
(CN102)
3
5 bracket (MDM)
SLIDER (CAM)
7 slider (cam)
• NOTE FOR INSTALLATION
OF SLIDER (CAM)
Set the shaft of cam gear to be
at the position in the figure.
3 bracket (guide L)
A
1 two screws
(DIA2.6)
2 ground
wire
Set the shaft of lever
(O/C) to be at the position
in the figure.
4 leaf spring
(electrostatic)
When attaching the slider (cam),
this part of the over write head
should be inside arrow A.
5 two screws
(DIA.2.6)
6 bracket (guide R)
19
BD (MD) BOARD, BASE UNIT (MBU-5A)
5 two flexible boards
(CN101, 104)
7 base unit (MBU-5A)
CN103
CN102
1 Remove two solders
of spindle motor leads
(M901).
6 BD (MD)
board
4 screw (M1.7)
2 Remove two solders
of sled motor leads (M902).
3 three screws
(DIA.2.6)
OVER WRITE HEAD (HR901)
2 screw (P1.7 × 6)
3 over write head
(HR901)
1 flexible board
(CN104)
20
SPINDLE MOTOR ASS’Y (M901), SLED MOTOR ASS’Y (M902)
3 gear
(SL-B)
4 three screws
(B2 × 5)
1 screw (M1.7)
2 gear (SL-A)
5 spindle motor ass’y
(M901)
6 two screws
(P1.7 × 2.5)
7 sled motor ass’y
(M902)
OPTICAL PICK-UP OF MD (KMS-260B/S1NP)
4 Turn over the optical pick-up.
6 optical pick-up
(KMS-260B/S1NP)
5 flexible board
1 screw (B2 × 8)
2 leaf spring (shaft)
3 main shaft
21
BACK PANEL ASS’Y
4 back panel ass’y
1 six screws
(BVTP3 × 10)
3 claw
2 claw
3 claw
SP BOARD, POWER BOARD AND MAIN BOARD
4 two connectors
(CN991, 992)
4 connector (CN993)
5 two screws (BVTT3 × 6)
8 connector
(CN994)
9 POWER board
3 wire (flat type) (25 core)
(CN109)
2 SP board
3 wire (flat type)
(15 core)
1 two connectors
(CN881, 882)
q; MAIN board
7
6 screw (BVTT3 × 6)
6 screw (BVTT3 × 6)
4 connector (CN110)
22
CD MECHANISM DECK (CDM55A-5SBD32)
4 holder (MDM)
3 screw (BVTT3 × 6)
7 CD mechanism deck
(CDM55A-5SB32)
5 screw (BVTT3 × 6)
1 wire (flat type) (19 core)
(CN109)
6 two claws
3 screw
(BVTT3 × 6)
2 connector
(CN110)
TRAY (CDM), GEAR AND CAM (CDM55)
4 belt (CDM55)
Note: when drawing out the tray (CDM), refer to
service notes DRAWING OUT THE TRAY
WHEN THE POWER IS OFF on page 6 .
7 roller
5 bushing
8 gear (B)
6 pulley (LDG)
9 gear (A)
q; cam (CDM55)
2 Push the claw in the
direction of arrow A.
A
1
tray (CDM)
3 Drawing out the tray (CDM).
2 Release the lock while pressing
this claw in the arrow direction.
23
HOLDER (BU) ASS’Y
1 floating screw
(PTPWH M2.6)
2 Remove the holder (BU) ass’y
in the direction of the arrow.
OPTICAL PICK-UP OF CD (KSS-213BH/Z-NP)
5 optical pick-up
(KSS-213BH/Z-NP)
3 wire (flat type) (16 core)
4
1 Release the lever in the
direction of arrow A.
A
2 sled shaft
24
BD (CD) BOARD, BASE (BU-5S) ASS’Y (M101) AND SLED MOTOR ASS’Y (M102)
4 two screws
(B2 × 4)
6 gear (M)
9 base (BU-5S) ass’y (M101)
8 two insulators (BU)
2 Remove the four solders.
8 two insulators (BU)
7 flatness gear
(P)
5 sled motor ass’y
(M102)
M101
M102
3 BD (CD) board
1 screw (BVTP2.6 × 8)
25
SECTION 4
TEST MODE
Note : About “R”
As this unit has only a few buttons, some operations require the use of remote commander (RM-SF3MD/provided with unit: 1-476-068-11)
buttons. These operations are indicated as “R” in this manual.
Example: MENU/NO “R” ...Press the [MENU/NO] button of the remote commander.
4-1.
PRECAUTIONS FOR USE OF TEST MODE
• As loading related operations will be performed regardless of the test mode operations being performed, be sure to check that the disc
is stopped before setting and removing it.
Even if the A (MD) button is pressed while the disc is rotating during continuous playback, continuous recording, etc., the disc will
not stop rotating.
Therefore, it will be ejected while rotating.
Be sure to press the A (MD) button after pressing the MENU/NO “R” button and the rotation of disc is stopped.
4-1-1. Recording laser emission mode and operating buttons
• Continuous recording mode (CREC MODE)
• Laser power check mode (LDPWR CHECK)
• Laser power adjustment mode (LDPWR ADJUST)
• Traverse (MO) check (EF MO CHECK)
• Traverse (MO) adjustment (EF MO ADJUST)
• When pressing the zREC button.
4-2.
SETTING THE TEST MODE
The following are two methods of entering the test mode.
Procedure 1: 1. Press the I/1 button to turn the power on.
2. Press the [FUNCTION] button to set the MD function.
3. While pressing the s (MD) and zREC buttons, press the I/1 button to enter the MD test mode and display “[Check]”.
When the test mode is set, “[Check]” will be displayed. Press the l m or M L button switches between the
following four groups; ···y [Check] y [Adjust] y [Service] y [Develop] y ···.
Procedure 2: 1. Press the I/1 button to turn the power on.
2. Press the [FUNCTION] button to set the MD function.
3. While pressing the s (MD) and [CD-MD SYNC] buttons, press the I/1 button to enter the MD test mode and display
“TEMP CHECK”.
By setting the test mode using this method, only the “Check” group of method 1 can be executed.
4-3.
RELEASING THE TEST MODE
Press the [REPEAT] button.
4-4.
BASIC OPERATIONS OF THE TEST MODE
All operations are performed using the l m or M L button , ENTER/YES “R” button, and MENU/NO “R” button.
The functions of these buttons are as follows.
Function name
Function
l m , M L buttons
Changes parameters and modes
ENTER/YES “R” button
Proceeds onto the next step. Finalizes
input
MENU/NO “R” button
Returns to previous step. Stops
operations
26
4-5.
SELECTING THE TEST MODE
There are 31 types of test modes as shown below. The groups can be switched by pessing the l m or M L button. After
selecting the group to be used, press the ENTER/YES “R” button. After setting a certain group, press the l m or M L button
switches between these modes.
Refer to “Group” in the table for details can be selected.
All items used for servicing can be treated using group S. So be carefully not to enter other groups by mistake.
Display
Contents
Mark
Group (*)
TEMP CHECK
Temperature compensation offset check
C
S
LDPWR CHECK
Laser power check
C
S
EF MO CHECK
Traverse (MO) check
C
S
EF CD CHECK
Traverse (CD) check
C
S
FBIAS CHECK
Focus bias check
C
S
Scurve CHECK
S letter check
(X)
C
VERIFYMODE
Non-volatile memory check
(X)
C
DETRK CHECK
Detrack check
(X)
C
TEMP ADJUST
Temperature compensation offset adjustment
A
S
LDPWR ADJUST
Laser power adjustment
A
S
EF MO ADJUST
Traverse (MO) adjustment
A
S
EF CD ADJUST
Traverse (CD) adjustment
A
S
FBIAS ADJUST
Focus bias adjustment
A
S
EEP MODE
Non-volatile memory control
MANUAL CMD
(X) (!)
D
Command transmission
(X)
D
SVDATA READ
Status display
(X)
ERR DP MODE
Error history display, clear
SLED MOVE
Sled check
(X)
D
ACCESS MODE
Access check
(X)
D
0920 CHECK
Outermost circumference check
(X)
D
HEAD ADJUST
Head position check
(X)
D
CPLAY2 MODE
Same functions as CPLAY MODE
(X)
D
CREC2 MODE
Same functions as CREC MODE
(X)
ADJ CLEAR
Initialization of non-volatile memory of adjustment value
A
S
AG Set (MO)
Auto gain output level adjustment (MO)
A
S
AG Set (CD)
Auto gain output level adjustment (CD)
A
Iop Read
IOP data display
Iop Write
IOP data write
INFORMATION
Microprocessing version display
C
CPLAY MODE
Continuous playback mode
C
A
S
D
CREC MODE
Continuous recording mode
C
A
S
D
D
S
D
C
A
Group (*)
C: Check
S: Service
S
S
S
S
A: Adjust
D: Develop
• For details of each adjustment mode, refer to “5. Electrical Adjustments”.
For details of “ERR DP MODE”, refer to “Self-Diagnosis Function” on page 2.
• If a different mode has been selected by mistake, press the MENU/NO “R” button to release that mode.
• Modes with (X) in the Mark column are not used for servicing and therefore are not described in detail. If these modes are set accidentally, press the MENU/NO “R” button to release the mode immediately. Be especially careful not to set the modes with (!) as they will
overwrite the non-volatile memory and reset it, and as a result, the unit will not operate normally.
27
4-5-1. Operating the Continuous Playback Mode
1. Entering the continuous playback mode
(1) Set the disc in the unit. (Whichever recordable discs or discs for playback only are available.)
(2) Press the l m or M L button and display “CPLAY MODE”.
(3) Press the ENTER/YES “R” button to change the display to “CPLAY MID”.
(4) When access completes, the display changes to “C1 =
AD = ”.
Note: The numbers “ ” displayed show you error rates and ADER.
2. Changing the parts to be played back
(1) Press the ENTER/YES “R” button during continuous playback to change the display as below.
“CPLAY MID” t “CPLAY OUT” t “CPLAY IN”
When pressed another time, the parts to be played back can be moved.
When access completes, the display changes to “C1 =
AD = ”.
(2)
Note: The numbers “ ” displayed show you error rates and ADER.
3. Ending the continuous playback mode
(1) Press the MENU/NO “R” button. The display will change to “CPLAY MODE”.
(2) Press the A (MD) button and take out the disc.
Note: The playback start addresses for IN, MID, and OUT are as follows.
IN : 40h cluster
MID : 300h cluster
OUT : 700h cluster
4-5-2. Operating the Continuous Recording Mode (Use only when performing self-recording/palyback check.)
1. Entering the continuous recording mode
(1) Set a recordable disc in the unit.
(2) Press the l m or M L button and display “CREC MODE”.
(3) Press the ENTER/YES “R” button to change the display to “CREC MID”.
)” and [z REC] indicator lights up.
(4) When access completes, the display changes to “CREC (
Note: The numbers “ ” displayed shows you the recording position addresses.
2. Changing the parts to be recorded
(1) When the ENTER/YES “R” button is pressed during continuous recording, the display changes as below.
“CREC MID” t “CREC OUT” t “CREC IN”
(2)
When pressed another time, the parts to be recorded can be changed. [z REC] indicator goes off.
When access completes, the display changes to “CREC (
)” and [z REC] indicator lights up.
Note: The numbers “ ” displayed shows you the recording position addresses.
3. Ending the continuous recording mode
(1) Press the MENU/NO “R” button. The display changes to “CREC MODE” and [z REC] indicator goes off.
(2) Press the A (MD) button and take out the disc.
Note 1: The recording start addresses for IN, MID, and OUT are as follows.
IN : 40h cluster
MID : 300h cluster
OUT : 700h cluster
Note 2: The MENU/NO “R” button can be used to stop recording anytime.
Note 3: Do not perform continuous recording for long periods of time above 5 minutes.
Note 4: During continuous recording, be careful not to apply vibration.
4-5-3. Non-Volatile Memory Mode (EEP MODE)
This mode reads and writes the contents of the non-volatile memory.
It is not used in servicing. If the unit entered this mode accidentally, press the MENU/NO “R” button immediately to release it.
4-6.
FUNCTIONS OF OTHER BUTTONS
Function
Contents
H S (MD)
Sets continuous playback when pressed in the STOP state. When pressed during continuous playback, the tracking
servo turns ON/OFF
s (MD)
Stops continuous playback and continuous recording
ML
The sled moves to the outer circumference only when this is pressed
lm
The sled moves to the inner circumference only when this is pressed
CLEAR “R”
Switches between the pit and groove modes when pressed
PLAY MODE/TUNING MODE
Switches the spindle servo mode (CLV-S y CLV-A)
DISP “R”
Switches the displayed contents each time the button is pressed
A (MD)
Ejects the disc
REPAET
Releases the test mode
28
4-7.
TEST MODE DISPLAYS
Each time the DISP “R” button is pressed, the display changes in the following order.
1. Mode display
Displays “TEMP ADJUST”, “CPLAYMODE”, etc.
2. Error rate display
Displays the error rate in the following way.
C1 = ssss AD = ss
C1 = Indicates the C1 error.
AD = Indicates ADER.
3. Address display
The address is displayed as follows. (MO: recordable disc, CD: playback only disc)
Press the CLEAR “R” button to switches between the groove display and pit display.
h = ssss s = ssss (MO pit and CD)
h = ssss a = ssss (MO groove)
h = Indicates the header address.
s = Indicates the SUBQ address.
a = Indicates the ADIP address.
Mode display
Error rate display
Note: “–” is displayed when servo is not imposed.
Address display
4. Auto gain display (Not used in servicing)
The auto gain is displayed as follows.
AG = ss/ss[ss]
Auto gain display
(Not used in servicing)
5. Detrack check display (Not used in servicing)
The detrack is displayed as follows.
ADR = sssssss
Detrack check display
(Not used in servicing)
IVR display
(Not used in servicing)
6. IVR display (Not used in servicing)
The IVR is displayed as follows.
[ss][ss][ss]
MEANINGS OF OTHER DISPLAYS
Contents
Display
When Lit
When Off
H (MD)*
During continuous playback (CLV: ON)
STOP (CLV: OFF)
S (MD)*
Tracking servo OFF
Tracking servo ON
zREC*
Recording mode ON
Recording mode OFF
SYNC
CLV low speed mode
CLV normal mode
L.SYNC
ABCD adjustment completed
OVER
Tracking offset cancel ON
1
Tracking auto gain OK
REPEAT
Focus auto gain OK
DISC
High reflection
Low reflection
SHUF
CLV-S
CLV-A
MONO
CLV LOCK
CLV UNLOCK
Tracking offset cancel OFF
* : Indicate by LED.
29
SECTION 5
ELECTRICAL ADJUSTMENTS
MD SECTION
5-1.
PARTS REPLACEMENT AND ADJUSTMENT
• Check and adjust the mechanism deck as follows.
The procedure changes according to the part replaced
• Abbreviation
OP : Optical pick-up
OWH : Overwrite head
• Temperature compensation offset check
• Laser power check
• Traverse check
• Focus bias check
• C PLAY check
• Self-recording/playback check
OK
NG
Check the sled and spindle
mechanisms.
Other causes can be suspected.
Parts Replacement and Repair
Has the OWH been replaced?
YES
NO
Has OP, IC171, IC101, or
IC121 been replaced?
YES
Initial setting of the adjustment value
NO
Has OP or IC171 been replaced?
NO
YES
IOP information recording
(IOP value labeled on OP)
Has IC171 or D101
been replaced?
YES
Temperature compensation offset adjustment
• Laser power adjustment
• Traverse adjustment
• Focus bias adjustment
• Error rate adjustment
• Focus bias check
• Auto gain adjustment
30
NO
Note : About “R”
As this unit has only a few buttons, some operations require the use of remote commander (RM-SF3MD/provided with unit: 1-476-068-11)
buttons. These operations are indicated as “R” in this manual.
Example: MENU/NO “R” ...Press the [MENU/NO] button of the remote commander.
5-2.
PRECAUTIONS FOR CHECKING LASER
DIODE EMISSION
To check the emission of the laser diode during adjustments, never
view directly from the top as this may lose your eye-sight.
5-3. PRECAUTIONS FOR USE OF OPTICAL
PICK-UP (KMS-260B)
As the laser diode in the optical pick-up is easily damaged by static
electricity, solder the laser tap of the flexible board when using it.
Before disconnecting the connector, desolder first. Before connecting the connector, be careful not to remove the solder. Also
take adequate measures to prevent damage by static electricity.
Handle the flexible board with care as it breaks easily.
pick-up
flexible board
2. Set the test mode when performing adjustments.
After completing the adjustments, release the test mode.
Perform the adjustments and checks in “group S” of the test
mode.
3. Perform the adjustments to be needed in the order shown.
4. Use the following tools and measuring devices.
• Check Disc (MD) TDYS-1
(Part No. 4-963-646-01)
• Test Disc (MDW-74/AU-1) (Part No. 8-892-341-41)
• Laser power meter LPM-8001 (Part No. J-2501-046-A)
or MD Laser power meter 8010S (Part No. J-2501-145-A)
• Oscilloscope (Measure after performing CAL of prove)
• Digital voltmeter
• Thermometer
• Jig for checking BD board waveform
(Part No. : J-2501-149-A)
5. When observing several signals on the oscilloscope, etc.,
make sure that VC and ground do not connect inside the oscilloscope.
(VC and ground will become short-circuited)
6. Using the above jig enables the waveform to be checked without the need to solder.
(Refer to Servicing Notes on page 9)
7. As the disc used will affect the adjustment results, make sure
that no dusts nor fingerprints are attached to it.
laser tap
Laser power meter
Optical pick-up flexible board
5-4.
PRECAUTIONS FOR ADJUSTMENTS
1. When replacing the following parts, perform the adjustments
and checks with a in the order shown in the following table.
Optical
Pick-up IC171
1. Initial setting of
adjustment value
a
a
BD Board
D101
×
When performing laser power checks and adjustment (electrical
adjustment), use of the new MD laser power meter 8010S (Part
No. J-2501-145-A) instead of the conventional laser power meter
is convenient.
It sharply reduces the time and trouble to set the laser power meter
sensor onto the objective lens of optical pick-up.
IC101, IC121 IC192
a
×
5-5.
CREATING CONTINUOUSLY-RECORDED
DISC
2. Recording of IOP
information
(Value on the optical pick-up label)
a
a
×
×
×
3. Temperature
compensation
offset adjustment
×
a
a
×
×
4. Laser power
adjustment
a
a
×
a
a
5. Traverse
adjustment
a
a
×
a
×
* This disc is used in focus bias adjustment and error rate check.
The following describes how to create a continuous recording
disc.
1. Insert a disc (blank disc) commercially available.
2. Press the l m or M L button and display “CREC
MODE”.
3. Press the ENTER/YES “R” button again to display “CREC
MID”.
Display “CREC (0300)” and start to recording.
4. Complete recording within 5 minutes.
5. Press the MENU/NO “R” button and stop recording .
6. Press the A (MD) button and remove the disc.
6. Focus bias
adjustment
a
a
×
a
×
The above has been how to create a continuous recorded data for
the focus bias adjustment/check and MO error rate check.
7. Error rate check
a
a
×
a
×
Note :
• Be careful not to apply vibration during continuous recording.
8. Auto gain output
level adjustment
a
a
×
a
×
31
5-6.
CHECK PRIOR TO REPAIRS
These checks are performed before replacing parts according to
“approximate specifications” to determine the faulty locations. For
details, refer to “Checks Prior to Parts Replacement and Adjustments” (See page 11).
5-6-1. Temperature Compensation Offset Check
When performing adjustments, set the internal temperature and
room temperature of 22 °C to 28 °C.
Checking Procedure:
1. Press the l m or M L button to display “TEMP
CHECK”.
2. Press the ENTER/YES “R” button.
3. “T=@@(##) [OK” should be displayed. If “T=@@ (##) [NG”
is displayed, it means that the results are bad.
(@@ indicates the current value set, and ## indicates the value
written in the non-volatile memory)
5-6-2. Laser Power Check
Before checking, check the IOP value of the optical pick-up.
(Refer to 8. Recording and Displaying IOP Information)
Connection :
laser
power meter
Optical pick-up
objective lens
digital voltmeter
BD (MD) board
CN110 pin 5 (I+3V)
CN110 pin 4 (IOP)
+
–
Checking Procedure:
1. Set the laser power meter on the objective lens of the optical
pick-up. (When it cannot be set properly, press the l m
button or M L button to move the optical pick-up)
Connect the digital voltmeter to CN110 pin 5 (I+3V) and
CN110 pin 4 (IOP) on the BD (MD) board.
2. Then, press the l m or M L button to display
“LDPWR CHECK”.
3. Press the ENTER/YES “R” button once to display “LD 0.9 mW
$ ”. Check that the reading of the laser power meter become
0.84 to 0.92 mW.
4. Press the ENTER/YES “R” button once more to display “LD
7.0 mW $ ”. Check that the reading the laser power meter
and digital voltmeter satisfy the specified value.
Specified Value:
Laser power meter reading : 7.0 ± 0.2 mW
Digital voltmeter reading : Value on the optical pick-up label
±10%
(Optical pick-up label)
KMS260A
27X40
B0825
Note 1: After step 4, each time the ENTER/YES “R” button is pressed,
the display will be switched “LD 0.7 mW $ ”, “LD 6.2 mW $
”, and “LD Wp
$ ”. Nothing needs to be performed
here.
5-6-3. Traverse Check
Note 1:Data will be erased during MO reading if a recorded disc is
used in this adjustment.
Note 2:If the traverse waveform is not clear, connect the oscilloscope
as shown in the following figure so that it can be seen more
clearly.
oscilloscope
(DC range)
BD (MD) board
330 k Ω
CN110 pin 3 (TEO)
CN110 pin 1 (VC)
+
–
10 pF
Connection :
oscilloscope
(DC range)
BD (MD) board
CN110 pin 3 (TEO)
CN110 pin 1 (VC)
+
–
V: 0.1 V/div
H: 10 ms/div
Checking Procedure:
1. Connect an oscilloscope to CN110 pin 3 (TEO) and CN110
pin 1 (VC) on the BD (MD) board.
2. Load a disc (any available on the market). (Refer to Note 1)
3. Press the M L button to move the optical pick-up outside
the pit.
4. Press the l m or M L button to display “EF MO
CHECK”.
5. Press the ENTER/YES “R” button to display “EFB = MO-R”.
(Laser power READ power/Focus servo ON/tracking servo
OFF/spindle (S) servo ON)
6. Observe the waveform of the oscilloscope, and check that the
specified value is satisfied. Do not press the l m or
M L button.
(Read power traverse checking)
Traverse Waveform
A
VC
B
Specified value : Below 10% offset value
Offset value (%) = IA – BI X 100
2 (A + B)
7. Press the ENTER/YES “R” button to display “EFB = MO-W”.
8. Observe the waveform of the oscilloscope, and check that the
specified value is satisfied. Do not press the l m or
M L button.
(Write power traverse checking)
Traverse Waveform
A
VC
lOP=82.5 mA in this case
lOP (mA) = Digital voltmeter reading (mV)/1 (Ω)
5. Press the MENU/NO “R” button to display “LDPWR CHECK”
and stop the laser emission.
(The MENU/NO “R” button is effective at all times to stop the
laser emission)
32
B
Specified value : Below 10% offset value
Offset value (%) = IA – BI X 100
2 (A + B)
9. Press the ENTER/YES “R” button to display “EFB = MO-P”.
Then, the optical pick-up moves to the pit area automatically
and servo is imposed.
10. Observe the waveform of the oscilloscope, and check that the
specified value is satisfied. Do not Press the l m or
M L button.
Traverse Waveform
A
VC
B
Specified value : Below 10% offset value
Offset value (%) = IA – BI X 100
2 (A + B)
11. Press the ENTER/YES “R” button to display “EF MO CHECK”
The disc stops rotating automatically.
12. Press the A (MD) button and take out the disc.
13. Load the check disc (MD) TDYS-1.
14. Press the l m or M L button and display “EF CD
CHECK”.
15. Press the ENTER/YES “R” button to display “EFB =
CD”.
Servo is imposed automatically.
16. Observe the waveform of the oscilloscope, and check that the
specified value is satisfied. Do not press the l m or
M L button.
Traverse Waveform
A
VC
B
Specified value : Below 10% offset value
Offset value (%) = IA – BI X 100
2 (A + B)
17. Press the ENTER/YES “R” button to display “EF CD CHECK”.
18. Press the A (MD) button and take out the check disc.
5-6-4. Focus Bias Check
Change the focus bias and check the focus tolerance amount.
Checking Procedure :
1. Load the test disk (MDW-74/AU-1).
2. Press the l m or M L button to display “CPLAY
MODE”.
3. Press the ENTER/YES “R” button twice to display “CPLAY
MID”.
4. Press the MENU/NO “R” button when “C1 =
AD = ” is
displayed.
5. Press the l m or M L button to display “FBIAS
CHECK”.
6. Press the ENTER/YES “R” button to display “
/ c = ”.
The first four digits indicate the C1 error rate, the two digits
after [/] indicate ADER, and the 2 digits after [c =] indicate
the focus bias value.
Check that the C1 error is below 50 and ADER is below 2.
7. Press the ENTER/YES “R” button to display “
/ b = ”.
Check that the C1 error is about 200 and ADER is below 2.
8. Press the ENTER/YES “R” button to display “
/ a = ”.
Check that the C1 error is about 200 and ADER is below 2.
9. Press the MENU/NO “R” button, then press the A (MD) button
and take out the test disc.
5-6-5. C PLAY Check
MO Error Rate Check
Checking Procedure :
1. Load the test disk (MDW-74/AU-1).
2. Press the l m or M L button to display “CPLAY
MODE”.
3. Press the ENTER/YES “R” button to display “CPLAY MID”.
4. The display changes to “C1 =
AD = ”.
5. If the C1 error rate is below 80, check that ADER is below 2.
6. Press the MENU/NO “R” button to stop playback, then press
the A (MD) button and take out the test disc.
CD Error Rate Check
Checking Procedure :
1. Load the check disc (MD) TDYS-1.
2. Press the l m or M L button to display “CPLAY
MODE”.
3. Press the ENTER/YES “R” button twice to display “CPLAY
MID”.
4. The display changes to “C1 =
AD = ”.
5. Check that the C1 error rate is below 50.
6. Press the MENU/NO “R” button to stop playback, then press
the A (MD) button and take out the check disc.
5-6-6. Self-Recording/playback Check
Prepare a continuous recording disc using the unit to be repaired
and check the error rate.
Checking Procedure :
1. Load a recordable disc (blank disc).
2. Press the l m or M L button to display “CREC
MODE”.
3. Press the ENTER/YES “R” button to display “CREC MID”.
4. When recording starts, lights up [z REC] indicator and display
“CREC @@@@” (@@@@ is the address).
5. About 1 minute later, press the MENU/NO “R” button to stop
continuous recording.
6. Press the l m or M L button to display “CPLAY
MODE”.
7. Press the ENTER/YES “R” button to display “CPLAY MID”.
AD = ” will be displayed.
8. “C1 =
9. Check that the C1 error becomes below 80 and the AD error
below 2.
10. Press the MENU/NO “R” button to stop playback, then press
the A (MD) button and take out the disc.
5-7.
INITIAL SETTING OF ADJUSTMENT VALUE
Note:
Mode which sets the adjustment results recorded in the non-volatile
memory to the initial setting value. However the results of the temperature compensation offset adjustment will not change to the initial setting
value.
If initial setting is performed, perform all adjustments again excluding the
temperature compensation offset adjustment.
For details of the initial setting, refer to “5-4. Precautions on Adjustments”
and execute the initial setting before the adjustment as required.
Setting Procedure :
1. Press the l m or M L button to display “ADJ
CLEAR”.
2. Press the ENTER/YES “R” button. “Complete!” will be
displayed momentarily and initial setting will be executed, after
which “ADJ CLEAR” will be displayed.
33
5-8.
RECORDING AND DISPLAYING THE IOP
INFORMATION
The IOP data can be recorded in the non-volatile memory. The
IOP value on the optical pick-up label and the IOP value after the
adjustment will be recorded. Recording these data eliminates the
need to read the label on the optical pick-up.
Recording Procedure :
1. Press the l m or M L button to display “Iop Write”,
and press the ENTER/YES “R” button.
2. The display becomes Ref=@@@.@ (@ is an arbitrary number) and the numbers which can be changed will blink.
3. Input the IOP value on the optical pick-up label.
To select the number : Press the l m or M L button.
To select the digit : Press the [SYNC REC] button.
4. When the ENTER/YES “R” button is pressed, the display
becomes “Measu=@@@.@” (@ is an arbitrary number).
5. As the adjustment results are recorded for the step 4 value.
Leave it as it is and press the ENTER/YES “R” button.
6. “Complete!” will be displayed momentarily. The value will be
recorded in the non-volatile memory and the display will become “Iop Write”.
Display Procedure :
1. Press the l m or M L button to display “Iop Read”.
2. “@@.@/##.#” is displayed and the recorded contents are displayed.
@@.@ indicates the IOP value on the optical pick-up label.
##.# indicates the IOP value after adjustment
3. To end, press the [CD-MD SYNC] button or MENU/NO “R”
button to display “Iop Read”.
5-9.
TEMPERATURE COMPENSATION OFFSET
ADJUSTMENT
Save the temperature data at that time in the non-volatile memory
as 25 ˚C reference data.
Note :
1. Usually, do not perform this adjustment.
2. Perform this adjustment in an ambient temperature of 22 ˚C to 28 ˚C.
Perform it immediately after the power is turned on when the internal
temperature of the unit is the same as the ambient temperature of 22 ˚C
to 28 ˚C.
3. When D101 has been replaced, perform this adjustment after the temperature of this part has become the ambient temperature.
Adjusting Procedure :
1. Press the l m or M L button to display “TEMP
ADJUST”.
2. Press the ENTER/YES “R” button to select the “TEMP
ADJUST” mode.
3. “TEMP =
[OK]” and the current temperature data will be
displayed.
4. To save the data, press the ENTER/YES “R” button.
When not saving the data, press the MENU/NO “R” button.
5. When the ENTER/YES “R” button is pressed, “TEMP =
SAVE” will be displayed and turned back to “TEMP ADJUST”
display then. When the MENU/NO “R” button is pressed,
“TEMP ADJUST” will be displayed immediately.
Specified Value :
The “TEMP =
” should be within “E0 - EF”, “F0 - FF”, “00 0F”, “10 - 1F” and “20 - 2F”.
5-10. LASER POWER ADJUSTMENT
Check the IOP value of the optical pick-up before adjustments.
(Refer to 8. Recording and Displaying IOP Information)
Connection :
laser
power meter
Optical pick-up
objective lens
digital voltmeter
BD (MD) board
CN110 pin 5 (I+3V)
CN110 pin 4 (IOP)
+
–
Adjusting Procedure :
1. Set the laser power meter on the objective lens of the optical
pick-up. (When it cannot be set properly, press the l m
or M L button to move the optical pick-up)
Connect the digital voltmeter to CN110 pin 5 (I+3V) and
CN110 pin 4 (IOP) on the BD (MD) board.
2. Press the l m or M L button to display “LDPWR
ADJUST”.
(Laser power : For adjustment)
3. Press the ENTER/YES “R” button once to display “LD 0.9 mW
$ ”.
4. Press the l m or M L button so that the reading of
the laser power meter becomes 0.85 to 0.91 mW. Press the
ENTER/YES “R” button after setting the range knob of the laser
power meter, and save the adjustment results. (“LD SAVE $
” will be displayed for a moment)
5. Then “LD 7.0 mW $ ” will be displayed.
6. Press the l m or M L button so that the reading of
the laser power meter becomes 6.9 to 7.1 mW, press
the ENTER/YES “R” button to save it.
Note: Do not perform the emission with 7.0 mW more than 15 seconds
continuously.
7. Then, press the l m or M L button to display
“LDPWR CHECK”.
8. Press the ENTER/YES “R” button once to display “LD 0.9 mW
$ ”. Check that the reading of the laser power meter become
0.85 to 0.91 mW.
9. Press the ENTER/YES “R” button once more to display “LD
7.0 mW $ ”. Check that the reading the laser power meter
and digital voltmeter satisfy the specified value.
Note down the digital voltmeter reading value.
Specified Value:
Laser power meter reading : 7.0 ± 0.2 mW
Digital voltmeter reading : Value on the optical pick-up label
±10%
(Optical pick-up label)
KMS260A
27X40
B0825
lOP=82.5 mA in this case
lOP (mA) = Digital voltmeter reading (mV)/1 (Ω)
10. Press the MENU/NO “R” button to display “LDPWR CHECK”
and stop the laser emission.
(The MENU/NO “R” button is effective at all times to stop the
laser emission.)
11. Press the l m or M L button to display “Iop Write”.
34
12. Press the ENTER/YES “R” button. When the display becomes
Ref=@@@.@ (@ is an arbitrary number), press the ENTER/
YES “R” button to display “Measu=@@@.@” (@ is an arbitrary
number).
13. The numbers which can be changed will blink. Input the Iop
value noted down at step 9.
To select the number : Press the l m or M L button.
To select the digit : Press the [SYNC REC] button.
14. When the ENTER/YES “R” button is pressed, “Complete!” will
be displayed momentarily. The value will be recorded in the
non-volatile memory and the display will become “Iop Write”.
Note 1: After step 4, each time the ENTER/YES “R” button is pressed,
the display will be switched “LD 0.7 mW $ ”, “LD 6.2 mW $
”, and “LD Wp
$ ”. Nothing needs to be performed
here.
7. Press the ENTER/YES “R” button and save the result of adjustment to the non-volatile memory (“EFB =
SAVE” will be
displayed for a moment. Then “EFB = MO-W” will be displayed).
8. Press the l m or M L button so that the waveform
of the oscilloscope becomes the specified value.
(When the l m or M L button is pressed, the of
“EFB” changes and the waveform changes) In this
adjustment, waveform varies at intervals of approx. 2%. Adjust
the waveform so that the specified value is satisfied as much
as possible.
(Write power traverse adjustment)
Traverse Waveform
A
5-11. TRAVERSE ADJUSTMENT
VC
B
Note 1:Data will be erased during MO reading if a recorded disc is
used in this adjustment.
Note 2:If the traverse waveform is not clear, connect the oscilloscope
as shown in the following figure so that it can be seen more
clearly.
oscilloscope
(DC range)
BD (MD) board
330 k Ω
CN110 pin 3 (TEO)
+
–
CN110 pin 1 (VC)
10 pF
Connection :
oscilloscope
(DC range)
Specification A = B
9. Press the ENTER/YES “R” button, and save the adjustment
results in the non-volatile memory. (“EFB = SAVE” will be
displayed for a moment)
MO-P” will be displayed.
10. “EFB =
The optical pick-up moves to the pit area automatically and
servo is imposed.
11. Press the l m or M L button until the waveform of
the oscilloscope moves closer to the specified value.
In this adjustment, waveform varies at intervals of approx. 2%.
Adjust the waveform so that the specified value is satisfied as
much as possible.
BD (MD) board
CN110 pin 3 (TEO)
CN110 pin 1 (VC)
Traverse Waveform
+
–
V: 0.1 V/div
H: 10 ms/div
Adjusting Procedure :
1. Connect an oscilloscope to CN110 pin 3 (TEO) and CN110
pin 1 (VC) on the BD (MD) board.
2. Load a disc (any available on the market). (Refer to Note 1)
3. Press the M L button to move the optical pick-up outside
the pit.
4. Press the l m or M L button to display “EF MO
ADJUST”.
5. Press the ENTER/YES “R” button to display “EFB = MO-R”.
(Laser power READ power/Focus servo ON/tracking servo
OFF/spindle (S) servo ON)
6. Press the l m or M L button so that the waveform
of the oscilloscope becomes the specified value.
(When the l m or M L button is pressed, the of
“EFB= ” changes and the waveform changes) In this
adjustment, waveform varies at intervals of approx. 2%. Adjust
the waveform so that the specified value is satisfied as much
as possible.
(Read power traverse adjustment)
Traverse Waveform
A
A
VC
B
Specification A = B
12. Press the ENTER/YES “R” button, and save the adjustment
results in the non-volatile memory. (“EFB = SAVE” will be
displayed for a moment)
Next “EF MO ADJUST” is displayed. The disc stops rotating
automatically.
13. Press the A (MD) button and take out the disc.
14. Load the check disc (MD) TDYS-1.
15. Press the l m or M L button to display “EF CD
ADJUST”.
16. Press the ENTER/YES “R” button to display “EFB =
CD”.
Servo is imposed automatically.
17. Press the l m or M L button so that the waveform
of the oscilloscope moves closer to the specified value.
In this adjustment, waveform varies at intervals of approx. 2%.
Adjust the waveform so that the specified value is satisfied as
much as possible.
Traverse Waveform
VC
B
Specification A = B
A
VC
B
Specification A = B
35
18. Press the ENTER/YES “R” button, display “EFB =
SAVE”
for a moment and save the adjustment results in the non-volatile
memory.
Next “EF CD ADJUST” will be displayed.
19. Press the A (MD) button and take out the disc.
5-12. FOCUS BIAS ADJUSTMENT
Adjusting Procedure :
1. Load the continuously-recorded disc. (Refer to “5-5. CREATING CONTINUOUSLY-RECORDED DISC”)
2. Press the l m or M L button to display “CPLAY
MODE”.
3. Press the ENTER/YES “R” button to display “CPLAY MID”.
4. Press the MENU/NO “R” button when “C1 =
AD = ” is
displayed.
5. Press the l m or M L button to display “FBIAS
ADJUST”.
6. Press the ENTER/YES “R” button to display “
/ a = ”.
The first four digits indicate the C1 error rate, the two digits
after [/] indicate ADER, and the 2 digits after [a =] indicate
the focus bias value.
7. Press the M L button and find the focus bias value at
which the C1 error rate becomes about 200 (Refer to Note 2).
/ b = ”.
8. Press the ENTER/YES “R” button to display “
9. Press the l m button and find the focus bias value at
which the C1 error rate becomes about 200.
/ c = ”.
10. Press the ENTER/YES “R” button to display “
11. Check that the C1 error rate is below 50 and ADER is 00.
Then press the ENTER/YES “R” button.
12. If the “( )” in “
( )” is above 20, press
the ENTER/YES “R” button.
If below 20, press the MENU/NO “R” button and repeat the adjustment from step 2.
13. Press the A (MD) button and take out the disc.
Note 1: The relation between the C1 error and focus bias is as shown in
the following figure. Find points A and B in the following figure
using the above adjustment. The focal point position C is automatically calculated from points A and B.
Note 2: As the C1 error rate changes, perform the adjustment using the
average vale.
C1 error
about
200
5-14. FOCUS BIAS CHECK
Change the focus bias and check the focus tolerance amount.
Checking Procedure :
1. Load the continuously-recorded disc. (Refer to “5-5. CREATING CONTINUOUSLY-RECORDED DISC”)
2. Press the l m or M L button to display “CPLAY
MODE”.
3. Press the ENTER/YES “R” button twice to display “CPLAY
MID”.
4. Press the MENU/NO “R” button when “C1 =
AD = ” is
displayed.
5. Press the l m or M L button to display “FBIAS
CHECK”.
/ c = ”.
6. Press the ENTER/YES “R” button to display “
The first four digits indicate the C1 error rate, the two digits
after [/] indicate ADER, and the 2 digits after [c =] indicate
the focus bias value.
Check that the C1 error is below 50 and ADER is below 2.
7. Press the ENTER/YES “R” button and display “
/ b=
”.
Check that the C1 error is about 200 and ADER is below 2.
8. Press the ENTER/YES “R” button and display “
/ a=
”.
Check that the C1 error is about 200 and ADER is below 2.
9. Press the MENU/NO “R” button, then press the A (MD) button
and take out the disc.
Note 1: If the C1 error and ADER are above other than the specified
value at points A (step 8. in the above) or B (step 7. in the above),
the focus bias adjustment may not have been carried out properly. Adjust perform the beginning again.
5-15. AUTO GAIN CONTROL OUTPUT LEVEL
ADJUSTMENT
B
C
A
Focus bias value
(F. BIAS)
5-13. ERROR RATE CHECK
5-13-1. CD Error Rate Check
Checking Procedure :
1. Load the check disc (MD) TDYS-1.
2. Press the l m or M L button and display “CPLAY
MODE”.
3. Press the ENTER/YES “R” button twice and display “CPLAY
MID”.
4. The display changes to “C1 =
AD = ”.
5. Check that the C1 error rate is below 20.
6. Press the MENU/NO “R” button to stop playback, then press
the A (MD) button and take out the check disc.
36
5-13-2. MO Error Rate Check
Checking Procedure :
1. Load the continuously-recorded disc. (Refer to “5-5. CREATING CONTINUOUSLY-RECORDED DISC”)
2. Press the l m or M L button to display “CPLAY
MODE”.
3. Press the ENTER/YES “R” button to display “CPLAY MID”.
4. The display changes to “C1 =
AD = ”.
5. If the C1 error rate is below 50, check that ADER is below 2.
6. Press the MENU/NO “R” button to stop playback, then press
the A (MD) button and take out the test disc.
Be sure to perform this adjustment when the optical pick-up is
replaced.
If the adjustment results becomes “Adjust NG!”, the optical pickup may be faulty or the servo system circuits may be abnormal.
5-15-1. CD Auto Gain Control Output Level Adjustment
Adjusting Procedure :
1. Load the check disc (MD) TDYS-1.
2. Press the l m or M L button to display “AG Set
(CD)”.
3. When the ENTER/YES “R” button is pressed, the adjustment
will be performed automatically.
“Complete!!” will then be displayed momentarily when the
value is recorded in the non-volatile memory, after which the
display changes to “AG Set (CD)”.
4. Press the A (MD) button and take out the check disc.
5-15-2. MO Auto Gain Control Output Level Adjustment
Adjusting Procedure :
1. Load the test disc (MDW-74/AU-1).
2. Press the l m or M L button to display “AG Set
(MO)”.
3. When the ENTER/YES “R” button is pressed, the adjustment
will be performed automatically.
“Complete!!” will then be displayed momentarily when the
value is recorded in the non-volatile memory, after which the
display changes to “AG Set (MO)”.
4. Press the A (MD) button and take out the test disc.
Adjustment Location:
– BD (MD) BOARD (Side A) –
CN101
D101
GND
I+3V
IOP
CN110
TEO
RF
VC
NOTE
IC171
– BD (MD) BOARD (Side B) –
IC101
IC121
IC192
Note: It is useful to use the jig for checking BD (MD) board waveform.
(Refer to Servicing Notes on page 9)
37
Note: Clear RF signal waveform means that the shape “◊” can be clearly
distinguished at the center of the waveform.
CD SECTION
Note :
1. CD Block is basically designed to operate without adjustment.
Therefore, check each item in order given.
2. Use YEDS-18 disc (3-702-101-01) unless otherwise indicated.
3. Use an oscilloscope with more than 10 MΩ impedance.
4. Clean the object lens by an applicator with neutral detergent when the
signal level is low than specified value with the following checks.
RF signal waveform
VOLT/DIV : 200 mV
TIME/DIV : 500 ns
level : 1.45 ±0.3 Vp-p
S-Curve Check
oscilloscope
E-F Balance (1 Track Jump) Check
BD (CD) board
TP(FE)
TP(VC)
+
–
oscilloscope
BD (CD) board
Procedure :
1. Connect an oscilloscope to TP (FE) and TP (VC).
2. Connect between TP (FE1) and TP (GND) by lead wire.
3. Connect between TP (AGCCON) and TP (GND) by lead wire.
4. Press the I/1 button to turn the power on.
5. Load a disc (YEDS-18) and press the H S (CD) button to
actuate the focus search. (In consequence of open and close the
disc tray, actuate the focus search)
6. Confirm that the oscilloscope waveform (S-curve) is
symmetrical between A and B. And confirm peak to peak level
within 4 ±1 Vp-p.
TP(TE)
TP(VC)
+
–
Procedure:
1. Connect an oscilloscope to TP (TE) and TP (VC) board.
2. Press the I/1 button to turn the power on.
3. Load a disc (YEDS-18) and playback the number five track.
4. Press the H S (CD) button. (Becomes the 1 track jump
mode.)
5. Confirm that the level B and A (DC voltage) on the oscilloscope
waveform.
1 track jump waveform
Center of
waveform
S-curve waveform
symmetry
B
A
within 4 ±1 Vp-p
A (DC voltage)
0V
B
level=1.3 ±0.6 Vp-p
7. After check, remove the lead wire connected in step 2 and 3.
Note : • Try to measure several times to make sure than the ratio
of A : B or B : A is more than 10 : 7.
• Take sweep time as long as possible and light up the
brightness to obtain best waveform.
Specification level: A × 100=less than ±22%
B
6.
After check, remove the lead wire connected in step 1.
Adjustment Location:
– BD (CD) BOARD (Conductor Side) –
RF Level Check
oscilloscope
BD (CD) board
TP(RF)
TP(VC)
+
–
TP (VC)
Procedure :
1. Connect an oscilloscope to TP (RF) and TP (VC).
2. Connect between TP (AGCCON) and TP (GND) by lead wire.
3. Press the I/1 button to turn the power on.
4. Load a disc (YEDS-18) and playback the number five track.
5. Confirm that the oscilloscope waveform is clear and check RF
signal level is correct or not.
6. After check, remove the lead wire connected in step 2.
TP (RF)
TP
(AGCCON)
TP (FE)
TP
(TE)
38
Symmetry
TP (FE1)
HCD-F3MD
SECTION 6
DIAGRAMS
6-1.
BLOCK DIAGRAM – CD SERVO Section –
FILTER
DIGITAL SIGNAL PROCESSOR,
DIGITAL FILTER, D/A CONVERTER,
DIGITAL SERVO PROCESSOR
IC101
VCC
VC
A
C
D
B
A C
B D
A
5
C
7
D
8
B
6
RF
SUMMING
AMP
F
RF EQ
AMP
FILO
16K
RAM
RF
16
51
FF
14
49
48
TRACKING
ERROR
AMP
E
11
F
10
AUTOMATIC
POWER
CONTROL
Q101
3
LD
XTA1
RF AC
ASYMMETRY
CORRECTION
EFM
DEMODULATION
DIGITAL
PLL
FD
LASER
DIODE
PD
TE
SUBCODE
PROCESSOR
13
CPU
INTERFACE
VC
BUFFER
APCLD/PD
AMP
12
LDON
PD
SERIAL IN
INTERFACE
22
21
T+
TRACKING
COIL
T–
2 AXIS DEVICE
F+
FOCUS
COIL
F–
SD+
M102
(SLED)
M
SD–
SP+
M101
(SPINDLE)
05
40
M
• R-ch is omitted due to same L-ch.
• SIGNAL PATH
: CD PLAY
: MD REC (DIGITAL)
SP–
RFDC
FE
TE
SE
CH2FIN 5
CH2RIN 6
30
31
CH1FIN 2
CH1RIN 3
FFDR
FRDR
17 CH3OUTF
18 CH3OUTR
OPERATIONAL
AMPLIFIER
ANALOG
SWITCH
A/D
CONVERTER
PWM
(Page 40)
DOUT
60
A
59
32
DATA
XLAT
81
58
CLOK
SCOR
XLON
32
33
CH3RIN 23 SRDR
CH3FIN 24 SFDR
29
28
CH4SIN 25
26
TFDR
TRDR
5
6
82
7
19
20
14
SENS
DATA
XLT
CLOK
SCOR
PWM
SERVO DSP
TRACKING
PWM
GENERATOR
TRACKING
SERVO
(Page 42)
SERVO
INTERFACE
SCLK
SSTP
LOUT1
LOUT2
FOCUS
PWM
GENERATOR
FOCUS
SERVO
SRDR
SFDR
SLED
PWM
GENERATOR
SLED
SERVO
AIN2
LOUT2
DIGITAL
CLV
MUTE 20
39
B
MAIN
SECTION
AIN1
PWM
GENERATOR
FFDR
FRDR
MDP
56
XRST
SQSO
33
9
27
SQCK
S101
(LIMIT)
15 CH4OUTF
16 CH4OUTR
X101
16.9344MHz
67
XRST
3
SQSO
1
SQCK
2
SENS
8
LMUT
TFDR
TRDR
14 CH1OUTF
13 CH1OUTR
D OUT
66
3rd ORDER
NOISE SHAPER
11 CH2OUTR
12 CH2OUTF
SERVO
AUTO
SEQUENCER
OVER SAMPLING
DIGITAL FILTER
43
39
41
HOLD SW
IC102
FOCUS/TRACKING COIL DRIVE,
SPINDLE/SLED MOTOR DRIVE
DIGITAL
OUT
ASY0
VREF
LD
POWER
D/A
INTERFACE
STAO
ASY1
VC
4
ERROR
CORRECTOR
TIMING
LOGIC
BD (MD)
SECTION
(1/2)
FOCUS
ERROR
AMP
E
F
55
DATA BUS
E
56 53
PCO
CTLV
54
IC103
RF AMP,
FOCUS/TRACKING ERROR AMP
DETECTOR
FILI
OPTICAL PICK-UP BLOCK
(KSS-213BH/Z-NP)
39
70
57
HOLD
71
72
CD-L
C
77
MAIN
SECTION
76
(Page 42)
75
R-CH
HCD-F3MD
BLOCK DIAGRAM – MD SERVO Section (1/2) –
DIGITAL SERVO SIGNAL PROCESSOR, DIGITAL SIGNAL PROCESSOR
EFM/ACIRC ENCODER/DECODER, SHOCK-PROOF MEMORY CONTROLLER,
ATRAC ENCODER/DECODER
IC121
OVER WRITE HEAD DRIVE
IC181
MORFO
MORFI
RFO
AGCI
RF AMP
BPF
A
B
C
D
TX
ABCD
ABCD
AMP
E
F
FOCUS
ERROR
AMP
IV AMP
AT
AMP
FE
ADAGC
ADIN
10
VC
ADFG
CVB
TRACKING
ERROR
AMP
TEMPI
TEMP
AMP
TE
SE
CSLED
SAMPLING
RATE
CONVERTER
SERIAL
12
WBLADJ
EQADJ
3TADJ
APCREF
APC
11
65
ABCD
OSCI
ANALOG
MUX
34
VC
SUBCODE
PROCESSOR
VC
FE
66
VC
68
TE
75
SE
74
SQSY
DQSY
MNT3
MNT2
MNT1
MNT0
MONITOR
CONTROL
A/D
CONVERTER
SENS
SRDT
SCLK
SWDT
XLAT
30
78
32
ADFG
26
28
27
ADIP
DEMODULATOR/
DECODER
APC
SPINDLE
SERVO
PARALLEL
DECODER
SWDT
VC
SERVO
DSP
PWM
GENERATOR
CPU
I/F
3
16
SCLK
17
XLAT
18
FOCNT
20
82
81
80
79
FOCNT
22 23 25
93
94
95
10
13
83 88 89 86 85 92 91
25
D0
D3
49 • 48 • 50 • 51
26
DADT
28
27
BCK
LRCK
DIVIDER
IC123
16
512FS
11
12
SQSY
DQSY
4
3
2
1
MNT3
9
8
6
5
7
SENS
SRDT
SCLK
SWDT
XLATCH
MNT2
MNT1
MNT0
D-RAM
IC124
A09
34 31 • 36 40 • 45
3
4
17
16
1
•
2
•
18
•
19
6
9
•
11
15
•
5
XWE
XRAS
XCAS
XOE
DQ1
DQ4
A0
A9
LDON
WRPWR
HF MODULE
SW
IC103,Q102-104
HF
MODULE
TRACKING
COIL
MOD
SLED/SPINDLE MOTOR DRIVE,
FOCUS/TRACKING COIL DRIVE
IC152
FOCUS
COIL
TRK–
TRK+
FSC+
FSC–
M902
(SLED)
M
M901
(SPINDLE)
M
SLED+
SLED–
SPDL+
SPDL–
10
12
DRIVER
14
15
21
23
DRIVER
18
19
27
25
DRIVER
29
30
6
8
DRIVER
3
4
PSB
16
TFDR
TRDR
FRDR
FFDR
SFDR
SRDR
SPFD
SPRD
XRST
DIG-RST
05
40
40
(Page 39)
21
XWE
47
XRAS
46
XCAS
44
XOE
43
A00
A
BD (CD)
SECTION
ADDT
AUTO
SEQUENCER
DTRF
CKRF
XLRF
AUTOMATIC
POWER
CONTROL
Q162, 163
ILCC
CLOCK
GENERATOR
BOTM
64
PEAK
63
35
31
XBCK
LRCK
20
PD
VICONV
LD
DOUT
AUX1
DOUT
20
DIGITAL
AUDIO
I/F
RFI
APCREF
FFDR
FRDR
TFDR
TRDR
SFDR
SRDR
LASER ON
SW
Q101
PD
ATRAC
ENCODER/
DECODER
LEVEL SHIFT
IC202 (1/2)
19
SCTX
XINT
DADT
TEMPR
D101
14
PLL
SHOCK
RESISTANT
MEMORY
CONTROLLER
RECP
15
67
29
BPF
ADFM
VCC
VC
3
33
EFM,
ACIRC,
ENCODER/
DECODER
IV AMP
E-F
BALANCE
VC
57
PCO
FILI
FILO
CLTV
XRST
4
5
6
7
8
9
E
38
BOTM
36
PEAK
37
PEAK
&
BOTTOM
J
C B
D A
AUX
P-P
F
I
RF
RF AGC & EQ
59
60
61
62
FG IN
DETECTOR
ADDT
RF AMP, FOCUS/TRACKING ERROR AMP
IC101
48 47 46 40
I
1
J
2
100
EFMO
4
5
6
OPTICAL PICK-UP BLOCK
(KMS-260B/S1NP)
1
2
3
DIN0
DIN1
SPFD
• SIGNAL PATH
: MD PLAY
: MD REC (ANALOG)
: MD REC (DIGITAL)
14
XINIT
OVER WRITE
HEAD DRIVE
Q181,182
15
9
•
12
10
•
13
8
•
11
FILTER
HR901
OVER WRITE
HEAD
SPRD
6-2.
D
BD (MD)
SECTION (2/2)
(Page 41)
HCD-F3MD
6-3.
BLOCK DIAGRAM – MD SERVO Section (2/2) –
A/D,D/A CONVERTER
IC201
18 DATAO
MD REC-L
(AD IN L)
VINL1 2
VINR1 4
R-CH
VOUTL 26
VOUTR 24
R-CH
MD-L
(DATA OUT L)
ADDT
MD LEVEL-L
BCK
LRCK
DADT
16 BCK
17 WS
19 DATAI
X201
22MHz
512FS OSC
IC202 (2/2)
12 SYSCLK
L3MODE 13
L3CLK 14
L3DATA 15
512FS
MD MECHANISM CONTROLLER
IC316
D
BD (MD)
SECTION (1/2)
(Page 40)
SCTX
XINT
SQSY
DQSY
MNT3
MNT2
MNT1
MNT0
SENS
SRDT
SCLK
SWDT
XLATCH
LIMIT-IN
72
73
27
75
79
80
81
82
78
36
37
35
66
63
SCTX
XINT
SQSY
DQSY
MNT3(S-LOCK)
MNT2(X-BUSY)
MNT1(SHOCK)
MNT0(F-OK)
SENS
SRDT
SCLK
SWDT
XLATCH
LIMIT-IN
L3-CLK 21
L3-DATA 22
L3-MODE 69
LEVEL-L
3
X OUT 13
X IN 15
X302
10MHz
I2C DATA 30
I2C CLK
I2C-SDA
29
I2C-SLK
E
MAIN SECTION
(Page 42)
57
67
65
77
LD ON
WRPWR
MOD
DIG-RST
LDON
WR PWR
MOD
DIG-RST
LIMIT IN
63
S101
(LIMIT)
REFLECT
58
S102-1
(REFLECT RATE DETECT)
PROTECT
59
S102-2
(PROTECT DETECT)
PACK-OUT
53
S602
(PACK OUT)
PB- P
60
S604
(PB POSITION)
REC-P
74
S601
(REC POSITION)
IIC DRIVER
Q112
IIC DRIVER
Q111
1
SDA
5
SCK
CN102
LOADING
2
10
MOTER
DRIVE
4
9
IC153
6
M903
(LOADING) M
LOADING SW
Q350
SDA
SCL
EEPROM
IC171
5
6
54
LD-IN
55
LD OUT
56
LD-LOW
88
87
SDA
SCL
TAPE CONTROL
P.DOWN 18
P.DOWN
S.RST 12
RESET
• R-ch is omitted due to same L-ch.
• SIGNAL PATH
: MD PLAY
: MD REC (ANALOG)
05
41
41
HCD-F3MD
6-4.
BLOCK DIAGRAM – MAIN Section –
MUTING CONTROL
Q551
MUTING
Q841
6
1 POWER AMP 10
IC801
TUNER UNIT
ANTENNA
L
STEREO
AM
TUNED
DO
COAXIAL
FM
75Ω
DI
CLK
CE
˚MUTE
RY881
+
R-CH
DBFB SW
Q301
DBFB DET
D881
PROTECT SW
Q872–873
OVER LOAD DET
Q802, 871
50
L
SPEAKER
IMPEDANCE
6 – 16Ω
–
51
54
TM881
–
RELAY DRIVE
Q881
R
R-CH
+
53
55
52
MUTING CONTROL
Q552
49
MUTING
Q801
REMOTE
CONTROL RECEIVER
IC602
BD (CD) SECTION
(Page 39)
R
J601
R-CH
PHONES
D602–609
R-CH
VOLUME
ROTARY
ENCODER
S601
59
32
56
81
58
82
19
33
57
86 87
88 93
89
CD-L
(Page 39)
PROTECT-IN
CD-RESET
SQ-DATA-IN
SENS
CD DATA
CD-LAT
CD CLK
SCOR
SQ-CLK
HOLD
VOL A
VOL B
SIRCS
HEADPHONE
KEY 0
KEY 1
KEY 2
OPEN
IN-SW
70
OPEN-SW
71
LOAD-IN
LOAD-OUT
67
66
REC OUT CONT
62LAT
62DATA
62CLK
FL-RESET
FL-CHIP SELECT
FL-CLK
FL-DATA
CD-POWER
POWER-ON
AC-CUT
RESET
FL-ON
XOUT
XIN
SUBXIN
SUBXOUT
83
38 47 48
34 36 37 35
5
43
22
12
42
13
15
10
11
S1
CD TRAY
OPEN/CLOSE DETECT
6
5
MOTOR
DRIVER
2
10
IC171
LOADING MOTOR
DRIVE
M
M103
(LOADING)
DATA
21
X502
32.768kHz
25
R-CH
CLK
LAT
20
E
94 30 29
X501
16MHz
SELECT
SWITCH
MICON
INTERFACE
I2C-SCL
I2C-SDA
MD-LEVEL L
MD-REC-L
MD-L
79
BASS
TU
39
TC
38
CD
37
MD
36
BD (CD) SECTION
R
72
IC501
MASTER CONTROLLER
MUTING CONTROL
Q102
35
26
R-CH
J101
TAPE
OUT
91
LED
LED
STANDBY
59 32 56 81 58 82 19 33 57
STKPOWER
F-RY
50
51
54
53
55
52
49
MUTING
Q101
(Page 41)
27
R-CH
R
L
BD (MD)
SECTION (2/2)
1 3
STEREO
TUNED
ST-DIN
ST-DOUT
ST-CLK
ST-CE
ST-MUTE
TA-MUTE
L
CLOSE
50 51 54 53 55 52 49 6
MD-REC-L
I2C-SDA
I2C-SDL
J101
TAPE
IN
LED DRIVE
Q607–610
S602–616
IC601
FL CONTROLLER
IC301
INPUT SELECT SWITCH,
TONE CONTROL,
ELECTRICAL VOLUME
1
DIG11
11 DIG1
62 DIG14
22
FLUORESCENT
INDICATOR
TUBE
FL601
RST
CS
SCK
SDATA
13
14
15
16
T900
POWER
TRANSFORMER
VF1
64 DIG12
24 SEG34 DIG0 12
GRID
DRIVE
S601
31 SEG27
33 SEG26
Q501
VF SW
Q972, 973
VF2
D986
FL ON SWITCH
Q974
D987
59 SEG0
–30V REG
Q971
VP (–30V)
P.DOWN
B.UP +5V
(FOR POWER ON)
B.UP +2.7V
(FOR STANDBY)
RESET
B.UP +3.3V
D924
BT922
FOR
BACK-UP
RECTIFIER
D975–978
REGULATOR
CONTROL
Q975
(Korean model)
CHARGER
Q921
+
3
D922
+5.6V REG
IC921
2
AC IN
RECTIFIER
D971–974
1
D921
SYS +5V
D923
AC ON RESET
Q941
AC OFF DETECTOR
IC941
D946
RECTIFIER
D992, 993
D943
T901
SUB POWER
TRANSFORMER
+B
• R-ch is omitted due to same L-ch.
D941
ST+12V
RECTIFIER
D832
–B
VOLTAGE SELECTOR
220 – 240V
110 – 120V
Hong Kong,
Taiwan models
• SIGNAL PATH
A+7.5V
: TUNER
3
: CD PLAY
+7.5V REG
IC902
2
1
3
+12V REG
IC901
1
RECTIFIER
D982–985
3
+5V REG
IC913
1
RECTIFIER
D981
3
+3.9V REG
IC912
2
1
D101
(Korean model)
: MD PLAY
DIG+5V
A+3.3V
: MD REC (ANALOG)
D912
: TAPE IN (PLAY)
SYS+3.3V
RY991
D913
RESET SWITCH
Q931
: TAPE OUT (REC)
3
MD RESET
IC931
5
D914
B.UP +3.3V
RELAY DRIVER
Q991
D911
A+5V
CD+5V
05
CD ON SWITCH
Q912
42
42
B+ SWITCH
Q911
MOTOR
+7V
3
+5V REG
IC911
1
3
+7V REG
IC903
1
• Circuit Boards Location
6-5.
NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
(In addition to this, the necessary note is printed in each block)
Note on Printed Wiring Boards:
• X : parts extracted from the component side.
• Y : parts extracted from the conductor side.
• b : Pattern from the side which enables seeing.
(The other layers' patterns are not indicated.)
AMP board
MD DIGITAL board
SP board
Caution:
Pattern face side:
(Side B)
Parts face side:
(Side A)
Parts on the pattern face side seen from
the pattern face are indicated.
Parts on the parts face side seen from
the parts face are indicated.
• Indication of transistor.
Note on Schematic Diagram:
• All capacitors are in µF unless otherwise noted. pF: µµF
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in Ω and 1/4 W or less unless otherwise
specified.
f
•
: internal component.
• 2 : nonflammable resistor.
• 5 : fusible resistor.
• C : panel designation.
Note: The components identified by mark 0 or dotted line
with mark 0 are critical for safety.
Replace only with part number specified.
C
Q
These are omitted.
B E
TUNER UNIT
Q
PANEL board
MAIN board
B C
E
These are omitted.
POWER board
SW board
BD (MD) board
BD (CD) board
LOADING board
43
43
• U : B+ Line.
• V : B– Line.
• Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal production tolerances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal production tolerances.
• Circled numbers refer to waveforms.
• Signal path.
F : TUNER
J : CD PLAY
E : MD PLAY
j : MD REC (ANALOG)
l : MD REC (DIGITAL)
d : TAPE IN (PLAY)
G : TAPE OUT (REC)
• Abbreviation
HK
: Hong Kong model
KR
: Korean model
TW :Taiwan model
HCD-F3MD
6-6.
PRINTED WIRING BOARD – BD (CD) Board –
• See page 43 for Circuit Boards Location.
TP(VC)
TP(RF)
(Page 52)
MAIN BOARD
CN109
TP(AGCCON)
TP(FE)
TP(TE)
TP(FE1)
19
05
05
OPTICAL PICK-UP BLOCK
KSS-213BH/Z-NP
44
44
HCD-F3MD
6-7.
SCHEMATIC DIAGRAM – BD (CD) Board –
• See page 62 for waveforms.
• See page 63 for IC Block Diagrams.
TP (VC)
TP (RF)
RF AMP,
FOCUS/TRACKING
ERROR AMP
TP (TE)
TP (FE)
TP
(
)
TP
(
Q101
AUTOMATIC
POWER
CONTROL
)
DIGITAL SIGNAL PROCESSOR,
DIGITAL FILTER,
D/A CONVERTER,
DIGITAL SERVO PROCESSOR
M102
(SLED)
M101
(SPINDLE)
SLED/SPINDLE MOTOR DRIVE,
FOCUS/TRACKING COIL DRIVE
MAIN BOARD
(3/3)
CN109
(Page 55)
05
• Voltages and waveforms are dc with respect to ground
under no-signal conditions.
no mark : CD PLAY
45
45
The components identified by mark 0 or dotted
line with mark 0 are critical for safety.
Replace only with part number specified.
HCD-F3MD
6-8.
SCHEMATIC DIAGRAM – BD (MD) Board (1/2) –
• See page 62 for waveforms.
• See page 63 for IC Block Diagrams.
• Voltages and waveforms are dc with respect to ground
under no-signal conditions.
no mark : MD STOP
(
) : MD PLAY
<
> : MD REC
: Impossible to measure
∗
OPTICAL PICK-UP BLOCK (KMS-260B/S1NP)
The components identified by mark 0 or dotted
line with mark 0 are critical for safety.
Replace only with part number specified.
(SPINDOL)
(SLEB)
Q102-104
HF MODULE SW
LASER
ON SW
SPINDLE/SLED
MOTOR DRIVE,
FOCUS/TRACKING
COIL DRIVE
Q162, 163
AUTOMATIC
POWER CONTROL
RF AMP,
FOCUS, TRACKING
ERROR AMP
PIN FUNCTION
IC101
CXA2523AR
05
BD (MD) BOARD
(2/2)
46
46
(Page 47)
HCD-F3MD
6-9.
SCHEMATIC DIAGRAM – BD (MD) Board (2/2) –
• See page 62 for waveforms.
• See page 63 for IC Block Diagrams.
BD (MD) BOARD
(1/2)
(Page 46)
MD DIGITAL
BOARD
CN104
DIVIDER
B
(Page 51)
PIN FUNCTION
MD DIGITAL
BOARD
CN103
C
(Page 51)
BA033FP-E2
S102-1
REFLECT RATE DETECT
S102-2
PROTECT DETECT
-1
-2
(LIMIT)
05
• Voltages and waveforms are dc with respect to ground
under no-signal conditions.
no mark : MD STOP
(
) : MD PLAY
<
> : MD REC
: Impossible to measure
∗
47
47
HCD-F3MD
6-10. PRINTED WIRING BOARD – BD (MD) Board –
• See page 43 for Circuit Boards Location.
• Semiconductor
Location
Ref. No.
(Page 50)
Location
D101
D181
D183
A-1
D-3
D-3
IC103
IC123
IC171
B-1
C-2
D-1
Q102
Q103
Q104
B-1
C-1
B-1
(Page 50)
• Semiconductor
Location
Ref. No.
There are a few cases that the part isn't mounted in model
is printed on diagrams.
48
48
Location
IC101
IC121
IC124
IC152
IC181
IC192
A-1
C-2
C-1
B-3
C-3
C-3
Q101
Q162
Q163
Q181
Q182
B-1
B-1
B-1
C-2
C-2
HCD-F3MD
6-11. SCHEMATIC DIAGRAM – BD SW (MD) Board –
6-13. SCHEMATIC DIAGRAM – LOADING (CD) Board –
S1
CD TRAY
OPEN/CLOSE
DETECT
MD DIGITAL
BOARD
CN102
CN151
5P
CLOSE
CLOSE
GND
OPEN
J
H
OPEN
(Page 51)
LOAD +
LOAD –
M103
(LOADING)
MAIN BOARD
(3/3)
(Page 55)
05
05
6-12. PRINTED WIRING BOARD – BD SW (MD) Board –
• See page 43 for Circuit Boards Location.
6-14. PRINTED WIRING BOARD – LOADING (CD) Board –
• See page 43 for Circuit Boards Location.
(Page 52)
MAIN
BOARD
CN110
(
M903
)
(LOADING)
J
S1
MD DIGITAL
BOARD
CN102
(
)
CLOSE
m
OPEN
(Page 50)
12
S1
CD TRAY OPEN/CLOSE
DETECT
05
05
49
49
12
HCD-F3MD
6-15. PRINTED WIRING BOARD – MD DIGITAL Board –
• See page 43 for Circuit Boards Location.
SW
BOARD
CN601
5
1
1
6
(Page 49)
10
7
BD(MD)
BOARD
CN102
(Page 48)
BD(MD)
BOARD(2/2)
CN103
(Page 48)
(Page 52)
MAIN
BOARD
CN107
05
05
50
50
HCD-F3MD
6-16. SCHEMATIC DIAGRAM – MD DIGITAL Board –
• See page 62 for waveforms.
• See page 63 for IC Block Diagrams.
(Page 54)
• Voltages and waveforms are dc with respect to ground
under no-signal conditions.
no mark : MD STOP
(
) : MD PLAY
<
> : MD REC
: Impossible to measure
∗
(Page 47)
(Page 49)
(Page 47)
51
51
HCD-F3MD
6-17. PRINTED WIRING BOARD – MAIN Board –
(Page 50)
• Semiconductor
Location
Ref. No.
• See page 43 for Circuit Boards Location.
(Page 44)
(Page 56)
Location
D171
D901
D911
D912
D913
D914
D921
D922
D923
D924
D941
D942
D943
D946
E-2
B-7
D-7
D-6
D-6
D-6
E-6
E-5
E-5
E-5
E-7
E-5
E-4
C-4
IC171
IC301
IC501
IC901
IC902
IC903
IC911
IC912
IC913
IC921
IC931
IC941
E-2
C-9
C-3
B-7
B-6
C-7
C-7
D-7
C-6
E-6
D-5
E-4
Q101
Q102
Q111
Q112
Q151
Q301
Q351
Q501
Q551
Q552
Q911
Q912
Q921
Q931
Q941
B-11
C-4
E-11
E-11
A-11
C-10
D-10
D-6
D-5
D-4
B-6
B-6
E-5
D-4
E-4
(Page 58)
(Page 49)
(Page 60)
There are a few cases that the part isn't mounted in model
is printed on diagrams.
52
52
HCD-F3MD
6-18. SCHEMATIC DIAGRAM – MAIN Board (1/3) –
• See page 63 for IC Block Diagrams.
(Page 57)
(Page 55)
(Page 54)
(Page 54)
53
53
(Page 55)
(Page 54)
• Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
no mark : TUNER
HCD-F3MD
6-19. SCHEMATIC DIAGRAM – MAIN Board (2/3) –
• See page 63 for IC Block Diagrams.
(Page 53)
(Page 53)
(Page 53)
(Page 61)
(Page 51)
(Page 55)
(Page 55)
(Page 55)
(Page 55)
54
54
(Page 55)
(Page 55)
• Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
no mark : TUNER
HCD-F3MD
6-20. SCHEMATIC DIAGRAM – MAIN Board (3/3) –
(Page 54)
(Page 53)
(Page 54)
• See page 62 for Waveforms.
(Page 54)
• See page 63 for IC Block Diagrams.
(Page 54)
(Page 54)
(Page 53)
(Page 54)
(Page 45)
(Page 49)
(Page 59)
55
55
• Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
no mark : TUNER
(
) : CD
HCD-F3MD
6-21. PRINTED WIRING BOARDS – AMP/SP Boards –
• See page 43 for Circuit Boards Location.
• Semiconductor
Location
Ref. No.
Location
D801
D802
D832
D851
D852
A-2
A-2
B-3
D-2
C-2
IC801
B-1
Q801
Q802
Q841
Q851
Q852
Q871
Q872
Q873
D-1
A-2
A-3
D-1
C-2
A-2
A-2
A-2
(Page 52)
(Page 60)
There are a few cases that the part isn't mounted in model
is printed on diagrams.
56
56
HCD-F3MD
6-22. SCHEMATIC DIAGRAM – AMP/SP Boards –
(Page 61)
• Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
no mark : TUNER
(Page 53)
57
57
The components identified by mark 0 or dotted
line with mark 0 are critical for safety.
Replace only with part number specified.
HCD-F3MD
6-23. PRINTED WIRING BOARD – PANEL Board –
• See page 43 for Circuit Boards Location.
• Semiconductor
Location
Ref. No.
FL601
FLUORESCENT INDICATOR TUBE
(Page 52)
58
58
Location
D661
D663
D664
D665
D667
D668
A-2
E-3
B-3
D-2
C-3
A-8
IC601
IC602
C-6
B-3
Q601
Q661
Q662
Q663
Q664
Q665
Q666
Q667
C-4
B-2
B-3
D-2
B-3
D-2
D-2
B-2
HCD-F3MD
6-24. SCHEMATIC DIAGRAM – PANEL Board –
• See page 62 for Waveform.
• See page 63 for IC Block Diagram.
(Page 55)
• Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
no mark : TUNER
59
59
HCD-F3MD
6-25. PRINTED WIRING BOARD – POWER Board –
• See page 43 for Circuit Boards Location.
(Page 52)
• Semiconductor
Location
Ref. No.
Location
D971
D972
D973
D974
D975
D976
D977
D978
D979
D980
D981
D982
D983
D984
D985
D986
D987
D991
D992
D993
B-3
B-2
B-3
B-2
A-3
A-3
A-3
A-3
A-2
A-3
B-1
A-1
A-1
A-1
A-1
A-5
A-5
A-4
C-2
C-2
Q971
Q972
Q973
Q974
Q975
Q991
B-2
A-5
A-5
A-4
B-3
B-3
(Page 56)
There are a few cases that the part isn't mounted in model
is printed on diagrams.
60
60
HCD-F3MD
6-26. SCHEMATIC DIAGRAM – POWER Board –
(Page 57)
(Page 54)
• Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
no mark : TUNER
61
61
The components identified by mark 0 or dotted
line with mark 0 are critical for safety.
Replace only with part number specified.
• Waveforms
– BD (CD) Board –
– BD (MD) Board –
1 IC101 yh (XTAI)
1 IC101 1, 2 (I, J) (MD play mode)
6 IC121 wk (XBCK)
16.9344MHz
– MAIN Board –
– PANEL Board –
1 IC202 9
1 IC501 q; (SUBXIN)
1 IC601 wa (XIN)
4.1Vp-p
3.8Vp-p
0.46Vp-p
3.1Vp-p
– MD DIGITAL Board –
2.8224MHz
22MHz
1.8Vp-p
0.8Vp-p
32.768kHz
2.34 µs
2 IC101 ta (RFAC) (CD play mode)
2 IC101 4 (A) (MD play mode)
7 IC121 wl (FS256)
Approx.
100mVp-p
1.45±0.3Vp-p
2 IC201 qs (SYSCLK)
3 IC101 8, 9 (E, F) (MD play mode)
Approx.
60mVp-p
Approx.
500mVp-p
3 IC201 qh (BCK)
3.3Vp-p
3.2Vp-p
176.4kHz
4 IC101 el (FE) (CD play mode)
2.8224MHz
4 IC121 qh (OSCI)
Approx.
200mVp-p
4 IC201 qj (WS)
3.8Vp-p
1.7Vp-p
22.581MHz
5 IC101 wh (MDP)
44.1kHz
5 IC121 wj (LRCK)
5 IC316 qg (XIN)
3.2Vp-p
2.4Vp-p
16MHz
22MHz
8 IC121 o; (FS4)
2.5Vp-p
44.1kHz
10MHz
7.5 µs
62
1.9Vp-p
4.4Vp-p
3.8Vp-p
11.29MHz
3 IC101 ra (TE) (CD play mode)
2 IC501 qg (XIN)
62
• IC Block Diagrams
– BD (CD) Board –
VDD
VSS
AVDD3
PCO
FILI
FILO
CLTV
AVSS3
RFAC
BIAS
ASYI
ASYO
AVDD0
IGEN
AVSS0
ADIO
RFDC
CE
TE
CXD2587Q
DOUT
IC101
60
59 58 57
56 55 54 53
52
51 50 49 48
47
46 45
44
43 42 41
LRCK 61
D/A
INTERFACE
PCMD 62
ERROR
CORRECTOR
INTERNAL BUS
DIGITAL
OUT
DIGITAL
PLL
16K
RAM
40 SE
39 FE
38 VC
ASYMMETRY
CORRECTION
OPERATIONAL
AMPLIFIER
ANALOG SWITCH
EFM
DEMODULATOR
A/D
CONVERTER
BCK 63
EMPH 64
XVDD 65
XTAI
XTAO
XVSS
AVDD1
AOUT1
AIN1
66
67
68
69
70
71
TIMING
LOGIC
CLOCK
GENERATOR
SERVO DSP
LOUT1 72
AVSS1 73
AVSS2 74
LOUT2 75
SUBCODE
PROCESSOR
PWM
PWM
RMUT 79
LMUT 80
TRACKING
SERVO
TRACKING
PWM GENERATOR
SLED
SERVO
SLED PWM
GENERATOR
SERVO
INTERFACE
OVER SAMPLING
DIGITAL FILTER
AIN2 76
FOCUS PWM
GENERATOR
26 MDP
25 LOCK
MIRR, DFCT,
FOK
DETECTOR
24 FOK
23 DFCT
22 MIRR
SERVO AUTO
SEQUENCER
C2PO
SCOR
SCLK
VDD
ATSK
SYSM
WFCK
XUGF
XPCK
GFS
9 10 11 12 13 14 15 16 17 18 19 20
4
SPOA
SPOB
XLON
5 6 7 8
DATA
XLAT
CLOK
SENS
XRST
21 COUT
CH4BIN
CH4SIN'
CH4SIN
CH3FIN
CH3RIN
CAPAIN3
GND
MUTE
POWVCC
CH3OUTR
CH3OUTF
CH4OUTR
CH4OUTF
BA5974FP-E2
PRFVCC
IC102
SQSO
SQCK
CPU
INTERFACE
3
FRDR
FFDR
TRDR
TFDR
SRDR
SFDR
DIGITAL
CLV
SERIAL IN
INTERFACE
1 2
33
32
31
30
29
28
27 SSTP
3rd ORDER
NOISE SHAPER
AOUT2 77
AVDD2 78
PWM GENERATOR
FOCUS
SERVO
37 XTSL
36 TES1
35 TEST
34 VSS
28
27
26
25
24
23
22
21
20
19
18
17
16
15
F
R
R
MUTE
INTERFACE
F
LEVEL SHIFT
THERMAL
SHUTDOWN
F
INTERFACE
F
R
F
R
INTERFACE
1
2
3
4
5
6
7
8
9
10
11
12
13
14
CH1RIN
CAPAIN1
CH2FIN
CH2RIN
CAPAIN2
GND
VREFIN
POWVCC
CH2OUTR
CH2OUTF
CH1OUTR
CH1OUTF
R
CH1FIN
R
VREFOUT
F
63
IC103
CXA2568M-T6
VCC
HOLD 1
VCC
APC PD AMP
+
–
24 VCC
23 LC/PD
APC LD AMP
VEE
22 LD ON
+
–
+
–
+
–
21 HOLD SW
20 AGC CONT
VEE
AGC VTH 2
50µA
LD 3
VCC
+
–
PD 4
19 RF BOT
VC
+
–
+
–
+
–
VC
A 5
+
–
B 6
VEE
18 RFTC
RF SUMMING AMP
C 7
+
–
VC
RF EQ AMP
VC
D 8
+
–
17 RF I
16 RF O
15 RFE
VC
FOCUS ERROR AMP
VEE
VEE 9
+
–
14 FE
VC
VC
+
–
F 10
–
+
–
+
E 11
TRACKING
ERROR AMP
VC
VC
VC BUFFER
VC 12
VC
64
+
–
VC
VEE
VCC
13 TE
– BD (MD) Board –
–
+
RF AGC
RF
PEAK
44
43 42
41
40
39
38
37
USROP
RF AGC
+
–
EQ
USRC
DET
+
–
RFA1
AGCI
45
COMPO
46
COMPP
OPN
47
ADDC
RFO
48
OPO
MORFI
CXA2523AR
MORFO
IC101
EQ
BPF3T
RFA2
I
1
J
2
–1
–
–2
–
RFA3
HLPT
–1
A
3
IVR
WBL
TEMP
PEAK
–2
BOTTOM
PBSW
GRVA
WBL
35 ABCD
34 FE
–
–
–
–
AA
36 BOTM
PBH
–1
GRV
+
–
4
3T
PTGR
–
1
–
–2
–
+
VC
P-P
–2
OFST
CVB
AUX
SW
PEAK3T
3T
33 AUX
BPFC
ABCDA
32 ADFG
B
+
–
5
IVR
C
31 ADAGC
BB
+
–
6
IVR
+
+
–
–
30 ADIN
FEA
CC
DET
BPF22
D
–
–
+
+
+
–
7
IVR
ADIP
AGC
WBL
ATA
DD
WBL
E
+
–
8
IVR
29 ADFM
+
–
EE
EE'
–1
PTGR
–
+
–
+
–2
–1
TESW
EBAL
–2
ESW
+
–
9
IVR
FF
IV
+
–
26 TE
TEA
3T
25 WBLADJ
VI CONV
EQ
AUXSW
PD 10
+
TG
WBL
FF'
FBAL
GSW
28 SE
27 CSLED
EFB
F
TG
SEA
BGR
COMMAND
–
+ –
VREF
SCRI - PARA
DECODE
APC 11
14
15
16
17
18
19
20
21
22 23
24
TEMPI
TEMPR
SWDT
SCLK
XLAT
XSTBY
F0CNT
VREF
EQADJ
VCC
3TADJ
13
GND
APCREF 12
65
MNT1 2
DCHG
APC
ADFG
F0CNT
XLRF
CKRF
DTRF
APCREF
LDDR
TRDR
TFDR
PWM
GENERATOR
EACH
BLOCK
MONITOR
CONTROL
MNT2 3
DVDD
92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76
SPINDLE
SERVO
MNT0 1
FFDR
FRDR
FS4
SRDR
SFDR
SPRD
94 93
AUTO
SEQUENCER
100 99 98 97 96 95
SPFD
FGIN
TEST1
TEST2
TEST3
DVSS
CXD2654R
EFMO
IC121
75 TE
74 SE
73 AVSS
MNT3 4
72 ADRB
ADIP
DECODER
71 ADRT
70 AVDD
SWDT 5
69 ADIO
SCLK 6
EACH
BLOCK
CPU I/F
XLAT 7
SRDT 8
68 VC
SERVO
DSP
SENS 9
A/D
CONVERTER
67 AUX1
ANALOG
MUX
XRST 10
66 FE
65 ABCD
64 BOTM
SQSY 11
63 PEAK
SUBCODE
PROCESSOR
DQSY 12
62 CLTV
EFM/ACIRC
ENCODER/
DECODER
PLL
RECP 13
SHOCK RESISTANT
MEMORY CONTROLLER
XINT 14
61 FILO
60 FILI
59 PCO
TX 15
58 AVSS
OSCI 16
CLOCK
GENERATOR
OSCO 17
XTSL 18
EACH
BLOCK
DIGITAL
AUDIO
I/F
DIN0 19
DIN1 20
COMP
SAMPLING
RATE
CONVERTER
57 RFI
56 BIAS
55 AVDD
54 ASYI
DOUT 21
53 ASYO
DATAI 22
ATRAC
ENCODER/DECODER
LRCKI 23
XBCKI 24
52 MVCI
ADDT 25
ADDRESS/DATA BUS A00 - A11, D0 - D3
D2
D0
D1
XWE
XRAS
A09
XCAS
XOE
DVSS
A11
A08
A07
A06
A05
A04
A10
A01
A00
CAPA+
IN2R
IN2F
VM2
OUT2F
PGND2
OUT2R
VM12
OUT1R
PGND1
OUT1F
VM1
IN1F
IN1R
VDD
BH6511FS
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
CHARGE
PUMP.
OSC
AMP
AMP
INTERFACE
AMP
AMP
INTERFACE
PREDRIVE
PREDRIVE
PREDRIVE
PREDRIVE
AMP
AMP
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
VM4
OUT4F
PGND4
OUT4R
VM34
OUT3R
PGND3
OUT3F
VM3
IN3F
IN3R
PSB
PSB
IN4F
INTERFACE
IN4R
AMP
VG
AMP
VDD
GND
INTERFACE
66
A02
A03
DVDD
FS256
LRCK
31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50
CAPA–
IC152
XBCK
DADT
26 27 28 29 30
51 D3
– MD DIGITAL Board –
VREF
7
VCONT
6
VREF
3
1
VINL2 6
LOGIC
PREDRIVER
VINL1 2
PGA
VADCN
VM
8
UDA1341TS
VADCP
IN1
9
IC201
VSS(AD)
IN2
10
LB1830M-S-TE-L
VDD(AD)
IC153
7
5
PGA
0DB/6DB
SWITCH
ADC2L
0DB/6DB
SWITCH
ADC2R
ADC1L
8 VINR2
ADC1R
VDDD 10
DIGITAL AGC
VSSD 11
DIGITAL MIXER
22 AGCSTAT
9 OVERFLOW
DECIMATION FILTER
DATAO 18
OUT2
GND
5
OUT1 VS
BCK 16
DIGITAL
WS 17
INTERFACE
L3-BUS
14 L3CLOCK
13 L3MODE
INTERFACE
DATAI 19
DSP FEATURES
QMUTE 23
INTERPOLATION FILTER
15 L3DATA
12 SYSCLK
PRAK
DETECTOR
20 TEST1
NOISE SHAPER
VREF 28
21 TEST2
DAC
VOUTL 26
DAC
VCC
4
25
27
VSS(DAC)
3
VDD(DAC)
1
2
4 VINR1
24 VOUTR
67
– MAIN Board –
M62428AFP600C
AVDD
VREFI
1
SUR R
2
SUR C
3
REF AMP
–
+
VREF
42 AGND
41 VREFO
SURROUND SW
MIC
AMP
AGND
+
–
IC301
40 MIC IN
IN1A
4
39 IN2A
IN1B
IN1C
B
A
A
B
BUFF
AMP1
6
38 IN2B
BUFF
AMP2
+
–
37 IN2C
+
–
IN1D
MIX
AMP1
7
+
–
–
+
5
MIX
AMP2
36 IN2D
8
35 REC OUT2
INBAS1
9
34 INBAS2
BASS
AMP1
BASS
AMP2
+
–
+
–
REC OUT1
NFBAS1 10
33 NFBAS2
32 FBAS2
FTRE1 12
31 FTRE2
+
–
+
–
FBAS1 11
TONE
AMP1
TONE OUT1 13
VOL IN1 14
TONE
AMP2
BASS BOOST SW
30 TONE OUT2
BASS BOOST SW
FBB1 15
29 VOL IN2
28 FBB2
BB
AMP1
27 NFBB2
+
–
FIN
AMP2
FIN
AMP1
BB
AMP2
+
–
+
–
+
–
NFBB1 16
INBB1 17
26 INBB2
OUT1 18
25 OUT2
24 AVDD
DGND 19
LATCH 20
DATA 21
68
23 DVDD
CPU
INTERFACE
22 CLK
IC171
LB1641
IC931
T.S.D
O.C.P
MOTOR
DRIVE
MOTOR
DRIVE
4
5
6
7
8
CLAMP
FWD.IN
REV.IN
VCC 1
VCC 2
9
10
MOTOR
DRIVE
3
NOISE
FILTER
2
NOISE
FILTER
GND
1
MOTOR
DRIVE
FWD/REV/STOP
CONTROL LOGIC
M62016L
COM
+
–
INTERRUPT SIGNAL
GENERATING BLOCK
COM
+
–
RESET SIGNAL
GENERATING BLOCK
1
2
3
4
5
GND
INT
RESET
CD
VCC
– PANEL Board –
IC601
M66004M8FP
DIG11 1
|
|
DIG0 12
64 DIG12
|
|
61 DIG15
DIGITAL
OUTPUT
CIRCUIT
RES 13
INDICATION
CONTROLLER
SERIAL
RECEIVE
CIRCUIT
P1 17
P0 18
VCC1 19
XOUT 20
XIN 21
VSS 22
OUTPUT
PORT
(2BIT)
INDICATION
CONTROL
RESISTOR
CLOCK
GENERATOR
CIRCUIT
CODE/COMMAND
CONTROL
CIRCUIT
CODE SELECT
CS 14
CLK 15
DATA 16
RAM WRITE
(35BIT x 16)
INDICATION
CODE
RESISTOR
(8BIT x 16)
DECODER
DECODER
(35BIT x 16)
CODE
WRITE
60 VCC2
SEG35 23
|
|
SEG27 31
SEGMENT OUTPUT CIRCUIT
59 SEG0
|
|
33 SEG26
VP 32
69
6-27.
IC PIN FUNCTION DESCRIPTION
• BD (MD) BOARD IC101 CXA2523AR (RF AMP, FOCUS/TRACKING ERROR AMP)
Pin No.
Pin Name
I/O
Description
1
I
I
I-V converted RF signal I input from the optical pick-up block detector
2
J
I
I-V converted RF signal J input from the optical pick-up block detector
3
VC
O
Middle point voltage (+1.65V) generation output terminal
4 to 9
A to F
I
Signal input from the optical pick-up detector
10
PD
I
Light amount monitor input from the optical pick-up block laser diode
11
APC
O
Laser amplifier output terminal to the automatic power control circuit
12
APCREF
I
Reference voltage input for setting laser power from the CXD2654R (IC121)
13
GND
—
14
TEMPI
I
Connected to the temperature sensor
15
TEMPR
O
Output terminal for a temperature sensor reference voltage
16
SWDT
I
Writing serial data input from the CXD2654R (IC121)
17
SCLK
I
Serial data transfer clock signal input from the CXD2654R (IC121)
18
XLAT
I
Serial data latch pulse signal input from the CXD2654R (IC121)
19
XSTBY
I
Standby signal input terminal
20
F0CNT
I
Center frequency control voltage input terminal of internal circuit (BPF22, BPF3T, EQ) input
from the CXD2654R (IC121)
21
VREF
O
Reference voltage output terminal
22
EQADJ
I
Center frequency setting terminal for the internal circuit (EQ)
23
3TADJ
I
Center frequency setting terminal for the internal circuit (BPF3T)
24
VCC
—
25
WBLADJ
I
Center frequency setting terminal for the internal circuit (BPF22)
26
TE
O
Tracking error signal output to the CXD2654R (IC121)
27
CSLED
I
Connected to the external capacitor for low-pass filter of the sled error signal
28
SE
O
Sled error signal output to the CXD2654R (IC121)
29
ADFM
O
FM signal output of the ADIP
30
ADIN
I
Receives a ADIP FM signal in AC coupling
31
ADAGC
I
Connected to the external capacitor for ADIP AGC
32
ADFG
O
ADIP duplex signal (22.05 kHz ± 1 kHz) output to the CXD2654R (IC121)
33
AUX
O
Auxiliary signal (I3 signal/temperature signal) output to the CXD2654R (IC121)
34
FE
O
Focus error signal output to the CXD2654R (IC121)
35
ABCD
O
Light amount signal (ABCD) output to the CXD2654R (IC121)
36
BOTM
O
Light amount signal (RF/ABCD) bottom hold output to the CXD2654R (IC121)
37
PEAK
O
Light amount signal (RF/ABCD) peak hold output to the CXD2654R (IC121)
38
RF
O
Playback EFM RF signal output to the CXD2654R (IC121)
39
RFAGC
I
Connected to the external capacitor for RF auto gain control circuit
40
AGCI
I
Receives a RF signal in AC coupling
41
COMPO
O
User comparator output terminal
42
COMPP
I
User comparator input terminal
43
ADDC
I
Connected to the external capacitor for cutting the low band of the ADIP amplifier
44
OPO
O
User operational amplifier output terminal
45
OPN
I
User operational amplifier inversion input terminal
46
RFO
O
RF signal output terminal
47
MORFI
I
Receives a MO RF signal in AC coupling
48
MORFO
O
MO RF signal output terminal
70
Ground terminal
“L”: standby (fixed at “H” in this set)
Not used (open)
Power supply terminal (+3.3V)
Not used (open)
Not used (fixed at “L”)
Not used (open)
Not used (fixed at “L”)
• BD (MD) BOARD IC121 CXD2654R
(DIGITAL SIGNAL PROCESSOR, DIGITAL SERVO PROCESSOR, EFM/ACIRC ENCODER/DECODER,
SHOCK PROOF MEMORY CONTROLLER, ATRAC ENCODER/DECODER)
Pin No.
Pin Name
I/O
Description
1
MNT0 (FOK)
O
Focus OK signal output to the MD mechanism controller (IC316)
“H” is output when focus is on (“L”: NG)
2
MNT1 (SHOCK)
O
Track jump detection signal output to the MD mechanism controller (IC316)
3
MNT2 (XBUSY)
O
Busy monitor signal output to the MD mechanism controller (IC316)
4
MNT3 (SLOCK)
O
Spindle servo lock status monitor signal output to the MD mechanism controller (IC316)
5
SWDT
I
Writing serial data signal input from the MD mechanism controller (IC316)
6
SCLK
I (S)
Serial data transfer clock signal input from the MD mechanism controller (IC316)
7
XLAT
I (S)
Serial data latch pulse signal input from the MD mechanism controller (IC316)
8
SRDT
O (3)
Reading serial data signal output to the MD mechanism controller (IC316)
9
SENS
O (3)
Internal status (SENSE) output to the MD mechanism controller (IC316)
10
XRST
I (S)
Reset signal input from the MD mechanism controller (IC316)
11
SQSY
O
Subcode Q sync (SCOR) output to the MD mechanism controller (IC316)
“L” is output every 13.3 msec Almost all, “H” is output
12
DQSY
O
Digital In U-bit CD format subcode Q sync (SCOR) output to the MD mechanism controller
(IC316) “L” is output every 13.3 msec Almost all, “H” is output
13
RECP
I
Laser power selection signal input from the MD mechanism controller (IC316)
“L”: playback mode, “H”: recording mode
14
XINT
O
Interrupt status output to the MD mechanism controller (IC316)
15
TX
O
Recording data output enable signal input from the MD mechanism controller (IC316)
Writing data transmission timing input (Also serves as the magnetic head on/off output)
16
OSCI
I
System clock signal (512Fs=90.3168 MHz) input terminal
17
OSCO
O
System clock signal (512Fs=90.3168 MHz) output terminal
18
XTSL
I
Input terminal for the system clock frequency setting
“L”: 45.1584 MHz, “H”: 22.5792 MHz (fixed at “H” in this set)
19
DIN0
I
Digital audio signal input terminal when recording mode
20
DIN1
I
Digital audio signal input terminal when recording mode
21
DOUT
O
Digital audio signal output terminal when playback mode
22
DATAI
I
Serial data input terminal
23
LRCKI
I
L/R sampling clock signal (44.1 kHz) input terminal
24
XBCKI
I
Bit clock signal (2.8224 MHz) input terminal
25
ADDT
I
Recording data input from the A/D, D/A converter (IC201)
26
DADT
O
Playback data output to the A/D, D/A converter (IC201)
27
LRCK
O
L/R sampling clock signal (44.1 kHz) output to the A/D, D/A converter (IC201)
28
XBCK
O
Bit clock signal (2.8224 MHz) output to the A/D, D/A converter (IC201)
29
FS256
O
Clock signal (11.2896 MHz) output terminal
“L”: reset
Not used (open)
Not used
Not used (fixed at “L”)
Not used (fixed at “L”)
Not used (fixed at “L”)
Not used (open)
30
DVDD
—
Power supply terminal (+3.3V) (digital system)
31 to 34
A03 to A00
O
Address signal output to the D-RAM (IC124)
35
A10
O
Address signal output to the external D-RAM
36 to 40
A04 to A08
O
Address signal output to the D-RAM (IC124)
41
A11
O
Address signal output to the external D-RAM
42
DVSS
—
Ground terminal (digital system)
43
XOE
O
Output enable signal output to the D-RAM (IC124)
44
XCAS
O
Column address strobe signal output to the D-RAM (IC124)
Not used (open)
Not used (open)
“L” active
“L” active
* I (S) stands for schmitt input, I (A) for analog input, O (3) for 3-state output, and O (A) for analog output in the column I/O.
71
Pin No.
Pin Name
I/O
Description
45
A09
O
Address signal output to the D-RAM (IC124)
46
XRAS
O
Row address strobe signal output to the D-RAM (IC124) “L” active
47
XWE
O
Write enable signal output to the D-RAM (IC124) “L” active
48
D1
I/O
49
D0
I/O
50
D2
I/O
51
D3
I/O
52
MVCI
I (S)
53
ASYO
O
54
ASYI
I (A)
55
AVDD
—
56
BIAS
I (A)
57
RFI
I (A)
58
AVSS
—
59
PCO
O (3)
Phase comparison output for master clock of the recording/playback EFM master PLL
Filter input for master clock of the recording/playback master PLL
Two-way data bus with the D-RAM (IC124)
Digital in PLL oscillation input from the external VCO
Not used (fixed at “L”)
Playback EFM full-swing output terminal
Playback EFM asymmetry comparator voltage input terminal
Power supply terminal (+3.3V) (analog system)
Playback EFM asymmetry circuit constant current input terminal
Playback EFM RF signal input from the CXA2523AR (IC101)
Ground terminal (analog system)
60
FILI
I (A)
61
FILO
O (A) Filter output for master clock of the recording/playback master PLL
62
CLTV
I (A)
Internal VCO control voltage input of the recording/playback master PLL
63
PEAK
I (A)
Light amount signal (RF/ABCD) peak hold input from the CXA2523AR (IC101)
64
BOTM
I (A)
Light amount signal (RF/ABCD) bottom hold input from the CXA2523AR (IC101)
65
ABCD
I (A)
Light amount signal (ABCD) input from the CXA2523AR (IC101)
66
FE
I (A)
Focus error signal input from the CXA2523AR (IC101)
67
AUX1
I (A)
Auxiliary signal (I3 signal/temperature signal) input from the CXA2523AR (IC101)
68
VC
I (A)
Middle point voltage (+1.65V) input from the CXA2523AR (IC101)
69
ADIO
70
AVDD
O (A) Monitor output of the A/D converter input signal
—
Not used (open)
Power supply terminal (+3.3V) (analog system)
71
ADRT
I (A)
A/D converter operational range upper limit voltage input terminal (fixed at “H” in this set)
72
ADRB
I (A)
A/D converter operational range lower limit voltage input terminal (fixed at “L” in this set)
73
AVSS
—
74
SE
I (A)
Sled error signal input from the CXA2523AR (IC101)
75
TE
I (A)
Tracking error signal input from the CXA2523AR (IC101)
76
DCHG
I (A)
Connected to the +3.3V power supply
77
TEST4
I
78
ADFG
I (S)
79
F0CNT
O
Filter f0 control signal output to the CXA2523AR (IC101)
80
XLRF
O
Serial data latch pulse signal output to the CXA2523AR (IC101)
81
CKRF
O
Serial data transfer clock signal output to the CXA2523AR (IC101)
82
DTRF
O
Writing serial data output to the CXA2523AR (IC101)
83
APCREF
O
Control signal output to the reference voltage generator circuit for the laser automatic power
control
84
TEST0
O
Input terminal for the test
85
TRDR
O
Tracking servo drive PWM signal (–) output to the BH6511FS (IC152)
Ground terminal (analog system)
Input terminal for the test
Not used (fixed at “H”)
ADIP duplex FM signal (22.05 kHz ± 1 kHz) input from the CXA2523AR (IC101)
Not used (open)
86
TFDR
O
Tracking servo drive PWM signal (+) output to the BH6511FS (IC152)
87
DVDD
—
Power supply terminal (+3.3V) (digital system)
88
FFDR
O
Focus servo drive PWM signal (+) output to the BH6511FS (IC152)
* I (S) stands for schmitt input, I (A) for analog input, O (3) for 3-state output, and O (A) for analog output in the column I/O.
72
Pin No.
Pin Name
I/O
Description
89
FRDR
O
Focus servo drive PWM signal (–) output to the BH6511FS (IC152)
90
FS4
O
Clock signal (176.4 kHz) output terminal (X’tal system)
91
SRDR
O
Sled servo drive PWM signal (–) output to the BH6511FS (IC152)
92
SFDR
O
Sled servo drive PWM signal (+) output to the BH6511FS (IC152)
93
SPRD
O
Spindle servo drive PWM signal (–) output to the BH6511FS (IC152)
94
SPFD
O
95
FGIN
I (S)
96
TEST1
I
97
TEST2
I
98
TEST3
I
99
DVSS
—
Ground terminal (digital system)
100
EFMO
O
EFM signal output to the overwrite head driver (IC181) when recording mode
Not used (open)
Spindle servo drive PWM signal (+) output to the BH6511FS (IC152)
FG signal input terminal
Not used (fixed at “L”)
Input terminal for the test (fixed at “L”)
* I (S) stands for schmitt input, I (A) for analog input, O (3) for 3-state output, and O (A) for analog output in the column I/O.
73
• MD DIGITAL BOARD IC316 M30624MG-A16FP (MD MECHANISM CONTROLLER)
Pin No.
Pin Name
I/O
1
WMOUT
O
Serial data output to the equipment connected to other unit
2
WMCLK
I
Serial data transfer clock signal input from the equipment connected to other unit
Not used (fixed at “L”)
3
LEVEL-L
O
Left channel level output to the master controller (IC501)
4
LEVEL-R
O
Right channel level output to the master controller (IC501)
5
LEDDATA
O
Serial data output terminal for the LED driver
6
—
O
Not used (open)
7
LEDCLK
O
Serial data transfer clock signal output terminal for the LED driver
8
BYTE
I
External data bus line byte selection signal input
9
CNVSS
—
10
XIN-T
I
Sub system clock input terminal (32.768 kHz)
11
XOUT-T
O
Sub system clock output terminal (32.768 kHz)
12
S.RST
I
System reset signal input from the reset signal generator (IC931) “L”: reset
For several hundreds msec. after the power supply rises, “L” is input, then it changes to “H”
13
XOUT
O
Main system clock output terminal (10 MHz)
14
GND
—
Ground terminal
15
XIN
I
16
3.3V
—
17
NMI
I
Non-maskable interrupt input terminal (fixed at “H” in this set)
18
P.DOWN
I
Power down detection signal input terminal
19
WMSYNC
I
Sync signal input from the equipment connected to other unit
20
I2CBUSY
O
Busy signal output for the I2C bus
21
L3CLK
O
L3 bus data transfer clock signal output to the A/D, D/A converter (IC201)
22
L3DATA
O
L3 bus data output to the A/D, D/A converter (IC201)
23
—
O
Not used (open)
24
ELEUP
O
Mini-disc elevator up/down motor control signal output terminal
“H” active Not used (open)
25
—
O
Not used (open)
26
ELEDOWN
O
Mini-disc elevator up/down motor control signal output terminal
“H” active Not used (open)
27
SQSY
I
Subcode Q sync (SCOR) input from the CXD2654R (IC121)
“L” is input every 13.3 msec Almost all, “H” is input
28
RESET SW
I
Reset switch input terminal
29
I2CCLK
I/O
Shift clock signal input/output terminal for the I2C bus
30
I2CDATA
I/O
Serial data input/output terminal for the I2C bus
31
FLDATA
O
Display serial data output terminal
32
—
O
Not used (open)
33
FLCLK
O
Display serial data transfer clock signal output terminal
34
FLCS
O
Display serial chip select signal output terminal
35
SWDT
O
Writing data output to the CXD2654R (IC121)
36
SRDT
I
Reading data input from the CXD2654R (IC121)
37
SCLK
O
Serial clock signal output to the CXD2654R (IC121)
38
OPTSEL0
O
Selection signal output for the optical input signal
39
SENSOR
I
Elevator position detect sensor input terminal
Not used (fixed at “L”)
40
SENSOR2
I
Elevator position detect sensor input terminal
Not used (fixed at “L”)
41
HEADDOWN
O
Over write head up/down motor control signal output terminal
“H” active Not used (open)
74
Description
Not used (open)
Not used (open)
Not used (open)
“L”: 16 bit, “H”: 8 bit (fixed at “L”)
Ground terminal
Not used (fixed at “L”)
Not used (open)
Main system clock input terminal (10 MHz)
Power supply terminal (+3.3V)
“L”: power down, normally: “H”
“L” active
“L”: reset
Not used (fixed at “L”)
Not used (pull up)
Not used (fixed at “L”)
Not used (open)
Not used (open)
“L” active
Not used (open)
Not used (open)
Pin No.
Pin Name
I/O
Description
42
HEADUP
O
Over write head up/down motor control signal output terminal
“H” active Not used (open)
43
JOG0
I
Jog dial pulse input terminal
(A phase input)
Not used (open)
44
JOG1
I
Jog dial pulse input terminal
(B phase input)
Not used (open)
45
WMINV
O
Clock signal phase inversion control signal output to the equipment connected to other unit
Not used (open)
46
LEDLAT
O
Serial data latch pulse output to the LED driver “L” active
47
OPTSEL1
O
Selection signal output terminal for digital signal
48
DARST
O
Reset signal output terminal “L”: reset
49
MUTE
O
Audio line muting control signal output terminal “L”: line muting on
Not used (open)
50
STB
O
Power control strobe signal output for the external device
“L”: standby mode, “H”: power on Not used (open)
51
CHACK-IN
I
Detection input from the disc loading in detect switch (S573)
“L”: disc chucking, others: “H” Not used
52
HOME
I
Detection input from the elevator home position detect switch
“L”: home position, others: “H” Not used (fixed at “L”)
53
PACK-OUT
I
Detection input from the disc loading out detect switch (S602)
“L”: loading out position, others: “H”
54
LDIN
O
Mini-disc loading motor control signal output to the motor driver (IC153)
“H” active *1
55
LDOUT
O
Mini-disc loading motor control signal output to the motor driver (IC153)
“H” active *1
56
LD-LOW
I
The loading motor drive voltage control signal output to the motor driver (IC153)
“H” active Not used (open)
57
LDON
O
Laser diode on/off control signal output to the automatic power control circuit “H”: laser on
58
REFLECT
I
Detection input from the disc reflection rate detect switch (S102-1)
“L”: high reflection rate disc, “H”: low reflection rate disc
59
PROTECT
I
Rec-proof claw detect input from the protect detect switch (S102-2) “H”: write protect
Not used (pull down)
Not used (open)
Not used (open)
60
PB-P
I
Detection input from the playback position detect switch (S604) “L” active
61
REC/PB
O
Not used (open)
62
3.3V
—
Power supply terminal (+3.3V)
63
LIMIT-IN
I
64
GND
—
Detection input from the sled limit-in detect switch (S101)
The optical pick-up is inner position when “L”
Ground terminal
Laser modulation select signal output to the HF module switch circuit
Playback power: “H”, Stop: “L”,
Recording power:
0.5 sec
65
MOD
O
2 sec
*1 Mini-disc loading motor (M903) control
Mode
Loading
Eject
Stop
Brake
LDIN (pin tf)
“H”
“L”
“L”
“H”
LDOUT (pin tg)
“L”
“H”
“L”
“H”
Terminal
75
Pin No.
Pin Name
I/O
Description
66
XLATCH
O
Serial data latch pulse signal output to the CXD2654R (IC121)
67
WRPWR
O
Laser power select signal output to the CXD2654R (IC121) and HF module switch circuit
“L”: playback mode, “H”: recording mode
68
LOADING
SEL: L
I
Setting terminal for the loading control method
“H”: not used IN switch (fixed at “L”)
69
L3MODE
O
L3 bus mode control signal output to the A/D, D/A converter (IC201)
70, 71
—
I
Not used (fixed at “H”)
72
SCTX
O
Recording data output enable signal output to the CXD2654R (IC121) and over write head driver
(IC181) Writing data transmission timing output (Also serves as the magnetic head on/off
output)
73
XINT
I
Interrupt status input from the CXD2654R (IC121)
74
REC-P
O
Detection input from the recording position detect switch (S601) “L”: recording position
75
DQSY
I
Digital In U-bit CD format subcode Q sync (SCOR) input from the CXD2654R (IC121)
“L” is input every 13.3 msec Almost all, “H” is input
76
—
I
Not used (open)
77
DIGRST
O
Reset signal output to the CXD2654R (IC121) and BH6511FS (IC152) “L”: reset
78
SENS
I
Internal status (SENSE) input from the CXD2654R (IC121)
79
MNT3
I
Spindle servo lock status monitor signal input from the CXD2654R (IC121)
80
MNT2
I
Busy signal input from the CXD2654R (IC121)
81
MNT1
I
Track jump detection signal input from the CXD2654R (IC121)
82
MNT0
I
Focus OK signal input from the CXD2654R (IC121)
“H” is input when focus is on (“L”: NG)
83
SENSOR SW
O
Control signal output for the sensor gain selection
84
DISK5
I
Detection input from the disc detect switch “L”: disc is set
Not used (fixed at “L”)
85
DISK1
I
Detection input from the disc detect switch “L”: disc is set
Not used (fixed at “L”)
86
DISK2
I
Detection input from the disc detect switch “L”: disc is set
Not used (fixed at “L”)
Not used (fixed at “L”)
87
SCL
O
Serial clock signal output to the EEPROM (IC171)
88
SDA
I/O
Two-way data bus with the EEPROM (IC171)
89
DISK4
I
Detection input from the disc detect switch “L”: disc is set
Not used (fixed at “L”)
90
DISK3
I
Detection input from the disc detect switch “L”: disc is set
Not used (fixed at “L”)
91
HEADSWDOWN
I
Detection input from the over write head down position detect switch
“L”: down position Not used (fixed at “L”)
92
HEADSW-UP
I
Detection input from the over write head up position detect switch
“L”: up position Not used (fixed at “L”)
93 to 95
KEY3 to KEY1
I
Key input terminal (A/D input)
96
AVSS
—
97
KEY0
I
Key input terminal (A/D input)
98
VREF
I
Reference voltage (+3.3V) input terminal (for A/D converter)
99
+3.3V
—
100
WMIN
I
76
Not used (fixed at “H”)
Ground terminal (for A/D converter)
Not used (fixed at “H”)
Power supply terminal (+3.3V)
Serial data input from the equipment connected to other unit
Not used (fixed at “L”)
• MAIN BOARD IC501 M30620MCA-A51FP (MASTER CONTROLLER)
Pin No.
Pin Name
I/O
Description
1
STKPOWER
O
Power amplifier (IC801) on/off selection signal output terminal “H”: power amplifier on
2
P
O
Power on/off control signal output terminal
3
F-RY
O
Speakers on/off relay (RY881) drive signal output terminal “H”: speakers on
4
R-RY
O
Rear speakers on/off relay drive signal output terminal “H”: speakers on
5
CD-POWER
O
Power on/off control signal output for the CD servo section “L”: standby, “H”: power on
6
TA-MUTE
O
Line muting on/off signal output terminal “L”: muting on
7
DBFB-H
O
H/L selection signal output terminal for DBFB
8
BYTE
I
External data bus line byte selection signal input “L”: 16 bits, “H”: 8 bits
Not used (fixed at “L”)
Not used (open)
Not used (open)
Not used (open)
9
CNVSS
—
10
SUBXIN
I
Sub system clock input terminal (32.768 kHz)
11
SUBXOUT
O
Sub system clock output terminal (32.768 kHz)
12
RESET
I
System reset signal input from the reset signal generator (IC941) “L”: reset
For several hundreds msec. after the power supply rises, “L” is input, then it changes to “H”
13
XOUT
O
Main system clock output terminal (16 MHz)
14
VSS
—
Ground terminal
15
XIN
I
16
Ground terminal
Main system clock input terminal (16 MHz)
VCC
—
17
NMI
I
Non-maskable interrupt input terminal
Fixed at “H” in this set
18
WAKE-UP
I
System wake up signal input terminal
Not used (fixed at “L”)
19
SCOR
I
Subcode sync (S0+S1) detection signal input from the CXD2587Q (IC101)
20
RDS-INT
I
Interrupt status input from the tuner pack
21
RDS-DATA
I
Serial data input from the tuner pack
22
AC-CUT
I
AC off detection signal input from the voltage detector (IC941) “L”: AC off
23
PL-CLK
O
Serial data transfer clock signal output to pro-logic circuit
24
PL-DATA
O
Serial data output to pro-logic circuit
25
PL-LAT
O
Serial data latch pulse output to pro-logic circuit
26
TIMER-LED
O
LED drive signal output of the timer indicator
27
PROTECT-IN
I
Over load detection signal input for speaker output “L”: over load
28
MD-RESET
O
MD reset signal output terminal
29
IIC-SCL
I/O
Shift clock signal input/output terminal for the IIC bus
30
Power supply terminal (+5V)
Not used (open)
Not used (open)
Not used (open)
Not used (open)
Not used (open)
Not used (open)
Not used (open)
IIC-DAT
I/O
Data input/output terminal for the IIC bus
31
TXD
—
Not used (fixed at “L”)
32
SQ-DATA-IN
I
Subcode Q data input from the CXD2587Q (IC101)
33
SQ-CLK
O
Subcode Q data reading clock signal output to the CXD2587Q (IC101)
34
FL-RESET
O
Reset signal output to the FL driver (IC601) “L”: reset
35
FL-DATA
O
Serial data output to the FL driver (IC601)
36
FL-CHIP SELECT
O
Chip select signal output to the FL driver (IC601) “L”: active
37
FL-CLK
O
Serial data transfer clock signal output to the FL driver (IC601)
38
62LAT
O
Serial data latch pulse signal output to the M62428AFP (IC301)
39
STBY-LED
O
LED drive signal output of the standby indicator
40, 41
V-CINE
O
Not used (open)
42
FL-ON
O
FL power on/off control signal output terminal
43
POWER-ON
O
Standby relay drive signal output terminal “L”: standby, “H”: power on
44
B-FREQ
O
Not used (open)
45
FUNC-SEL1
O
Function selection signal output terminal
Not used (open)
Not used (open)
Not used (open)
77
Pin No.
Pin Name
I/O
46
OPT-SEL
O
47
62DATA
O
Serial data output to the M62428AFP (IC301)
48
62CLK
O
Serial data transfer clock signal output to the M62428AFP (IC301)
49
ST-MUTE
O
Tuner muting control signal output to the tuner pack “L”: muting on
50
STEREO
I
FM stereo detection signal input from the tuner pack
51
TUNED
I
Tuning detection signal input from the tuner pack
52
ST-CE
O
PLL chip enable signal output to the tuner pack
53
ST-DOUT
O
PLL serial data output to the tuner pack
78
Description
Optical signal selection signal output terminal Not used (open)
54
ST-DIN
I
PLL serial data input from the tuner pack
55
ST-CLK
O
PLL serial data transfer clock signal output to the tuner pack
56
SENSE
I
Internal status detection monitor input from the CXD2587Q (IC101)
57
HOLD
O
Automatic power control hold signal output to the CXA2568M (IC103)
58
CD-LAT
O
Serial data latch pulse output to the CXD2587Q (IC101)
59
CD-RESET
O
Reset signal output to the CXD2587Q (IC101) and BA5974FP (IC102)
60
DISC-SENS
I
Detection input from the disc in detect switch Not used (fixed at “H”)
61
TABLE-SENS
I
Detection input from the disc tray detect switch Not used (fixed at “H”)
62
VCC
—
Power supply terminal (+5V)
63
TABLE-L
O
Disc tray open/close motor drive signal output terminal Not used (open)
64
VSS
—
Ground terminal
65
TABLE-R
O
Disc tray open/close motor drive signal output terminal Not used (open)
66
LOAD-OUT
O
CD loading motor control signal output to the motor driver (IC171)
67
LOAD-IN
O
CD loading motor control signal output to the motor driver (IC171)
68
UP-SW
I
Not used (fixed at “L”)
69
DISC-LED
I
Not used (fixed at “L”)
70
IN-SW
I
Detection input from the CD disc tray open/close detect switch (S1)
“L”: CD disc tray close
71
OUT-SW
I
Detection input from the CD disc tray open/close detect switch (S1)
“L”: CD disc tray open
72
LED
O
LED drive signal output of the CD playback indicator (D665 (green)) “L”: LED on
73
LED
O
LED drive signal output of the MD disc in indicator (D664) “H”: LED on
74
LED
O
LED drive signal output of the MD playback indicator (D661 (green)) “L”: LED on
75
LED
O
LED drive signal output of the MD pause indicator (D661 (amber)) “L”: LED on
76
LED
O
LED drive signal output of the CD playback indicator (D665 (amber)) “L”: LED on
77
LED
O
LED drive signal output of the CD disc in indicator (D667) “H”: LED on
78
LED
O
LED drive signal output of the MD recording indicator (D663) “H”: LED on
79
STANDBY
O
LED drive signal output of the standby indicator (D668) “H”: LED on
80
LED
O
LED drive signal output terminal Not used (open)
81
CD-DATA
O
Serial data output to the CXD2587Q (IC101)
82
CD-CLK
O
Serial data transfer clock signal output to the CXD2587Q (IC101)
83
REC OUT CONT
O
Muting on/off control signal output of tape output signal “L”: muting on
84
JOGA
I
Jog dial pulse input from the rotary encoder A phase input Not used (open)
85
JOGB
I
Jog dial pulse input from the rotary encoder B phase input Not used (open)
86
VOL A
I
Jog dial pulse input from the rotary encoder (S601 VOLUME) A phase input
87
VOL B
I
Jog dial pulse input from the rotary encoder (S601 VOLUME) B phase input
88
SIRCS
I
Remote control signal input from the remote control receiver (IC602)
89
KEY0
I
Key input terminal (A/D input) S602 (I/1 key input)
Pin No.
Pin Name
I/O
Description
90
KEY1
I
Key input terminal (A/D input)
keys input)
91
KEY2
I
Key input terminal (A/D input) S609 to 616 (FUNCTION, +M L, TUNER/BAND, –l
m, z REC, CD-MD SYNC, STEREO/MONO REPEAT, TUNING MODE/PLAY MODE keys
input)
92
MD-REC-R
I
R-ch level input from the MD mechanism controller (IC316)
93
HEADPHONE
I
Headphone detection signal input terminal “H”: headphone in
94
MD-REC-L
I
L-ch level input from the MD mechanism controller (IC316)
95
MODEL-IN
I
96
AG
—
97
SPEC-IN
I
S603 to 608 (CDs, CDHS, CDA, MDs, MDHS, MDA,
Model destination setting terminal
Ground terminal
Model specification setting terminal
98
VREF
I
99
AVCC
—
Power supply terminal (+5V)
100
TEST
—
Test setting terminal (fixed at “L”)
Reference voltage (+5V) input terminal
79
SECTION 7
EXPLODED VIEWS
NOTE:
• -XX and -X mean standardized parts, so they
may have some difference from the original
one.
• Color Indication of Appearance Parts
Example:
KNOB, BALANCE (WHITE) . . . (RED)
↑
↑
Parts Color Cabinet's Color
• Abbreviation
HK : Hong Kong model
TW : Taiwan model
KR : Korean model
• Items marked “*” are not stocked since they
are seldom required for routine service. Some
delay should be anticipated when ordering
these items.
• The mechanical parts with no reference number in the exploded views are not supplied.
• Hardware (# mark) list and accessories and
packing materials are given in the last of the
electrical parts list.
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
11
(1)
21
CASE, FRONT PANEL SECTION
11
9
20
10
21
#2
MDM-5GA
not supplied
20
19
7
19
#1
8
12
FL601
13
19
10
14
3
4
16
15
5
2
17
not supplied
1
#1
18
supplied with S601
Ref. No.
Part No.
Description
1
2
2
3
3
4-228-468-01
4-228-471-01
4-228-471-11
X-4952-957-4
X-4952-996-4
KNOB (VOL)
PLATE (FL), INDICATION (SILVER)
PLATE (FL), INDICATION (WHITE)
PANEL ASSY, FRONT (S) (SILVER)
PANEL ASSY (W), FRONT (WHITE)
4
5
7
8
* 9
4-216-729-71
4-223-771-21
A-4475-916-A
4-212-590-22
4-228-798-41
LID (CARTRIDGE)
SPRING (LID)
PANEL BOARD, COMPLETE
HOLDER (FL)
CASE (SILVER)
* 9
10
11
4-228-798-51 CASE (WHITE)
3-363-099-11 SCREW (CASE 3 TP2)
4-212-589-01 SCREW (+BVTPWH M3), STEP
80
Remark
Ref. No.
Part No.
Description
12
13
14
15
16
4-221-097-02
1-777-240-11
1-791-211-11
A-4475-917-A
1-773-212-11
BRACKET (MDM)
WIRE (FLAT TYPE) (21 CORE)
WIRE (FLAT TYPE) (23 CORE)
MD DIGITAL BOARD, COMPLETE
WIRE (FLAT TYPE) (25 CORE)
17
18
18
19
20
1-792-756-11
4-228-469-01
4-228-469-11
4-951-620-01
4-996-223-01
WIRE (FLAT TYPE) (29 CORE)
PANEL, LOADING (SILVER)
PANEL, LOADING (WHITE)
SCREW (2.6X8), +BVTP
INSULATOR (F) (BLACK)
21
FL601
4-999-347-01 INSULATOR (R) (GREEN)
1-517-985-11 INDICATOR TUBE, FLUORESCENT
Remark
(2)
CHASSIS SECTION
T900
52
#1
not supplied
60
51
T901
57
62
53
#3
#2
not supplied
#2
#1
58
#1
55
#2
59
#1
CDM55A-5SBD32
#1
61
not supplied
#1
#1
not supplied
#1
56
The components identified by mark 0 or dotted
line with mark 0 are critical for safety.
Replace only with part number specified.
Ref. No.
Part No.
Description
51
51
52
52
53
A-4475-921-A
A-4475-925-A
A-4475-920-A
A-4475-924-A
X-4953-470-1
AMP BOARD, COMPLETE (HK, TW)
AMP BOARD, COMPLETE (KR)
POWER BOARD, COMPLETE (HK, TW)
POWER BOARD, COMPLETE (KR)
PANEL ASSY, BACK
55
56
56
57
1-674-628-12
A-4475-919-A
A-4475-923-A
1-693-473-31
SP BOARD
MAIN BOARD, COMPLETE (HK, TW)
MAIN BOARD, COMPLETE (KR)
TUNER (FM/AM TUNER UNIT) (TW)
Remark
Ref. No.
Part No.
Description
Remark
57
58
59
60
61
1-693-473-41
3-703-244-00
1-773-115-11
1-773-006-11
1-569-972-21
TUNER (FM/AM TUNER UNIT) (HK, KR)
BUSHING (2104), CORD
WIRE (FLAT TYPE) (19 CORE)
WIRE (FLAT TYPE) (15 CORE)
SOCKET, SHORT 2P
0 62
0 62
0 T900
0 T901
1-769-079-21
1-769-744-11
1-433-970-11
1-433-966-11
CORD, POWER (KR)
CORD, POWER (HK, TW)
TRANSFORMER, POWER
TRANSFORMER, POWER
81
(3)
MD MECHANISM DECK SECTION
(MDM-5GA)
113
124
111
112
113
121
110
114
119
115
108
122
#8
120
109
123
116
not supplied
102
M903
117
#8
118
101
106
104
#4
105
MBU-5A
#8
Ref. No.
Part No.
Description
* 101
* 102
* 104
105
106
1-671-115-21
4-996-217-01
4-996-218-01
4-996-277-01
4-996-226-01
SW BOARD
CHASSIS
BRACKET (GUIDE R)
SPRING (O/C), TENSION
LEVER (O/C)
* 108
109
110
111
112
4-996-225-01
4-988-466-11
4-996-219-01
4-996-220-01
4-996-221-01
BRACKET (GUIDE L)
SPRING (ELECTROSTATIC), LEAF
GEAR (CAM GEAR)
GEAR (A)
GEAR (B)
113
114
82
4-933-134-01 SCREW (+PTPWH M2.6X6)
4-996-224-01 SCREW (1.7X3), +PWH
Remark
Ref. No.
Part No.
Description
115
116
117
118
119
4-996-227-14
4-996-229-01
4-998-763-14
A-4680-200-G
4-996-214-01
LEVER (HEAD)
SPRING (HEAD LEVER), TORSION
SPRING (SHUTTER), LEAF
HOLDER COMPLETE ASSY
SPRING (SLIDER), TENSION
120
121
122
123
* 124
4-996-216-01
4-996-215-11
X-4949-668-3
X-4949-667-4
4-996-211-11
SPRING (HOLDER), TENSION
SPRING (LOCK LEVER), TENSION
SLIDER ASSY
HOLDER ASSY
SLIDER (CAM)
M903
X-4949-264-1 MOTOR ASSY, LOADING (MD)
Remark
(4)
MD BASE UNIT SECTION
(MBU-5A)
165
152
164
HR901
166
171
#6
163
#7
167
#7
170
#7
168
172
169
156
162
not supplied
#7
155
#7
#5
not supplied
159
#6
M901
160
161
S102
#7
154
157
#7
152
153
158
M902
151
152
Part No.
Description
165
166
167
168
169
4-996-261-01
4-996-264-01
4-996-265-01
4-996-256-11
4-996-257-01
GEAR (SL-B)
SPRING (SHAFT), LEAF
SHAFT, MAIN
SL (BASE)
RACK (SL)
SPRING, COMPRESSION
GEAR (SL-C)
PC BOARD, FLEXIBLE
BASE (BU-A)
OPTICAL PICK-UP KMS-260B/S1NP
170
171
172
HR901
M901
4-996-263-01
4-988-560-01
4-211-036-01
1-500-502-11
A-4672-475-A
SPRING (CLV), TORSION
SCREW (+P 1.7X6)
SCREW (1.7X2.5), +PWH
HEAD, OVER WRITE
MOTOR ASSY, SPINDLE (MD)
CHASSIS, BU
BASE (BU-B)
MAGNET, ABSORPTION
GEAR (SL-A)
M902
S102
A-4672-474-A MOTOR ASSY, SLED (MD)
1-762-148-21 SWITCH, PUSH (2 KEY)
(PROTECT/REFLECT RATE DETECT)
Ref. No.
Part No.
Description
151
152
* 153
* 154
155
A-4699-893-A
3-372-761-01
4-996-267-01
4-996-255-01
4-900-590-01
BD (MD) BOARD, COMPLETE
SCREW (M1.7), TAPPING
BASE (BU-D)
BASE (BU-C)
SCREW, PRECISION SMALL
156
157
* 158
* 159
0 160
4-996-258-01
4-996-262-01
1-667-954-11
4-210-664-11
A-4672-541-A
* 161
* 162
163
164
4-996-252-01
4-996-254-01
4-967-688-11
4-996-260-01
Remark
Ref. No.
The components identified by mark 0 or dotted
line with mark 0 are critical for safety.
Replace only with part number specified.
Remark
83
(5)
CD MECHANISM DECK SECTION
(CDM55A-5SBD32)
213
211
not supplied
212
207
209
219
208
210
206
205
220
201
204
214
203
215
M103
214
214
not supplied
(BU-5SBD32)
202
216
216
#4
218
not supplied
Ref. No.
Part No.
Description
201
202
203
204
205
4-925-315-31
1-674-336-12
4-220-231-01
4-220-229-01
4-220-239-01
DAMPER
LOADING BOARD
TRAY (CDM)
LEVER (SW)
SPRING, TORSION
206
207
208
209
210
4-220-237-01
4-220-238-01
4-220-234-01
4-221-815-01
4-220-233-01
GEAR (A)
GEAR (B)
PULLEY (LDG)
ROLLER
CAM (CDM55)
211
4-221-816-01 BELT (CDM55)
84
Remark
Ref. No.
217
Part No.
Description
212
213
214
215
216
4-221-916-01
A-4672-773-A
4-985-672-01
4-220-230-01
4-959-996-01
BUSHING
PULLEY (AT) ASSY
SCREW (+PTPWH M2.6), FLOATING
CHASSIS
SPRING (932), COMPRESSION
217
218
219
220
M103
A-4672-772-A
4-221-817-02
4-224-629-11
4-220-951-02
A-4672-771-A
HOLDER (BU) ASSY
SHAFT (BU)
SHEET (AT)
SHEET (KH)
MOTOR (LD) ASSY (LOADING) (CD)
Remark
(6)
CD BASE UNIT SECTION
(BU-5SBD32)
255
256
#12
zC
257
253
254
M102
254
M101
(including zC)
258
252
251
The components identified by mark 0 or dotted
line with mark 0 are critical for safety.
Replace only with part number specified.
Ref. No.
Part No.
Description
251
* 252
253
254
0 255
4-951-620-01
A-4724-375-A
4-917-565-01
4-951-940-01
8-820-113-01
SCREW (2.6X8), +BVTP
BD (CD) BOARD, COMPLETE
SHAFT, SLED
INSULATOR (BU)
OPTICAL PICK-UP KSS-213BH/Z-NP
Remark
Ref. No.
256
257
258
M101
M102
Part No.
Description
1-782-817-11
4-917-567-01
4-917-564-01
X-4952-989-1
X-4917-504-1
WIRE (FLAT TYPE) (16 CORE)
GEAR (M)
GEAR (P), FLATNESS
BASE (BU-5S) ASSY (CD)
MOTOR ASSY (SLED) (CD)
Remark
85
SECTION 8
ELECTRICAL PARTS LIST
AMP
NOTE:
• Due to standardization, replacements in the
parts list may be different from the parts specified in the diagrams or the components used
on the set.
• -XX and -X mean standardized parts, so they
may have some difference from the original
one.
• RESISTORS
All resistors are in ohms.
METAL: Metal-film resistor.
METAL OXIDE: Metal oxide-film resistor.
F: nonflammable
• Abbreviation
HK : Hong Kong model
KR : Korean model
TW : Taiwan model
Ref. No.
Part No.
• Items marked “*” are not stocked since they
are seldom required for routine service.
Some delay should be anticipated when ordering these items.
• SEMICONDUCTORS
In each case, u: µ, for example:
uA. . : µA. .
uPA. . : µPA. .
uPB. . : µPB. .
uPC. . : µPC. .
uPD. . : µPD. .
• CAPACITORS
uF: µF
• COILS
uH: µH
Description
Remark
Ref. No.
D851
D852
A-4475-921-A AMP BOARD, COMPLETE (HK, TW)
A-4475-925-A AMP BOARD, COMPLETE (KR)
********************
Part No.
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
When indicating parts by reference
number, please include the board.
Description
Remark
8-719-911-19 DIODE 1SS119-25
8-719-911-19 DIODE 1SS119-25
< FUSE >
11-533-293-11 FUSE HOLDER
0 F801
0 F802
< CAPACITOR >
1-532-504-31 FUSE (T4AL/250V)
1-532-504-31 FUSE (T4AL/250V)
< IC >
C801
C802
C803
C804
C805
1-124-721-11
1-162-286-31
1-126-964-11
1-162-288-31
1-126-051-11
ELECT
CERAMIC
ELECT
CERAMIC
ELECT
10uF
220PF
10uF
330PF
47uF
20%
10%
20%
10%
20%
50V
50V
50V
50V
50V
IC801
C806
C807
C808
C821
C822
1-126-051-11
1-136-495-11
1-136-495-11
1-126-965-11
1-126-052-11
ELECT
FILM
FILM
ELECT
ELECT
47uF
0.068uF
0.068uF
22uF
100uF
20%
5%
5%
20%
20%
50V
50V
50V
50V
50V
Q801
Q802
Q841
Q851
Q852
8-729-044-08
8-729-620-05
8-729-900-80
8-729-044-08
8-729-620-05
C823
C824
C831
C832
C833
1-136-165-00
1-164-159-11
1-126-052-11
1-136-165-00
1-126-860-11
FILM
CERAMIC
ELECT
FILM
ELECT
0.1uF
0.1uF
100uF
0.1uF
3300uF
5%
20%
5%
20%
50V
50V
50V
50V
35V
Q871
Q872
Q873
8-729-119-76 TRANSISTOR
8-729-620-05 TRANSISTOR
8-729-620-05 TRANSISTOR
C834
C835
C836
C841
C851
1-136-165-00
1-126-860-11
1-136-165-00
1-126-960-11
1-124-721-11
FILM
ELECT
FILM
ELECT
ELECT
0.1uF
3300uF
0.1uF
1uF
10uF
5%
20%
5%
20%
20%
50V
35V
50V
50V
50V
R801
R802
R803
R804
R805
1-249-421-11
1-249-429-11
1-249-437-11
1-249-437-11
1-249-417-11
CARBON
CARBON
CARBON
CARBON
CARBON
2.2K
10K
47K
47K
1K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
C852
C853
C854
C855
C856
1-162-286-31
1-126-964-11
1-162-288-31
1-126-051-11
1-126-051-11
CERAMIC
ELECT
CERAMIC
ELECT
ELECT
220PF
10uF
330PF
47uF
47uF
10%
20%
10%
20%
20%
50V
50V
50V
50V
50V
R806
R807
R808
0 R809
R810
1-249-437-11
1-260-103-11
1-260-103-11
1-217-151-00
1-249-417-11
CARBON
CARBON
CARBON
METAL
CARBON
47K
2.2K
2.2K
0.22
1K
5%
5%
5%
10%
5%
1/4W
1/2W
1/2W
2W
F
1/4W
C857
C858
C871
1-136-495-11 FILM
1-136-495-11 FILM
1-126-933-11 ELECT
0.068uF
0.068uF
100uF
5%
5%
20%
50V
50V
16V
R811
R812
0 R821
R822
R823
1-249-431-11
1-260-076-11
1-212-881-11
1-260-328-11
1-260-328-11
CARBON
CARBON
FUSIBLE
CARBON
CARBON
15K
10
100
1K
1K
5%
5%
5%
5%
5%
1/4W
1/2W
1/4W F
1/2W
1/2W
R824
R825
0 R831
R841
R842
1-249-441-11
1-249-433-11
1-212-881-11
1-249-437-11
1-249-437-11
CARBON
CARBON
FUSIBLE
CARBON
CARBON
100K
22K
100
47K
47K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W F
1/4W
1/4W
1-249-441-11 CARBON
1-247-807-31 CARBON
100K
100
5%
5%
1/4W
1/4W
< CONNECTOR >
CN801
* CN802
1-770-731-11 CONNECTOR, BOARD TO BOARD 12P
1-564-518-11 PLUG, CONNECTOR 3P
< DIODE >
D801
D802
D832
86
8-719-911-19 DIODE 1SS119-25
8-719-911-19 DIODE 1SS119-25
8-719-028-23 DIODE D3SBA20-4101
8-749-920-13 IC STK4132MK2
< TRANSISTOR >
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SD1915 (F)-T (TA). SO
2SC2603-EF
DTC114ES
2SD1915 (F)-T (TA). SO
2SC2603-EF
2SA1175-HFE
2SC2603-EF
2SC2603-EF
< RESISTOR >
R843
R844
AMP
Ref. No.
Part No.
Description
Remark
R845
R851
R852
1-249-441-11 CARBON
1-249-421-11 CARBON
1-249-429-11 CARBON
100K
2.2K
10K
5%
5%
5%
1/4W
1/4W
1/4W
R853
R854
R855
R856
R857
1-249-437-11
1-249-437-11
1-249-417-11
1-249-437-11
1-260-103-11
CARBON
CARBON
CARBON
CARBON
CARBON
47K
47K
1K
47K
2.2K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/2W
R858
0 R859
R860
R861
R862
1-260-103-11
1-217-151-00
1-249-417-11
1-249-431-11
1-260-076-11
CARBON
METAL
CARBON
CARBON
CARBON
2.2K
0.22
1K
15K
10
5%
10%
5%
5%
5%
1/2W
2W
F
1/4W
1/4W
1/2W
Ref. No.
BD (CD)
Part No.
Description
C157
C159
C161
C162
C163
1-163-009-11
1-163-019-00
1-126-206-11
1-126-205-11
1-126-206-11
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
ELECT CHIP
ELECT CHIP
0.001uF
0.0068uF
100uF
47uF
100uF
10%
10%
20%
20%
20%
50V
50V
6.3V
6.3V
6.3V
Remark
C165
C167
C168
C171
C172
1-163-038-11
1-163-235-11
1-163-235-11
1-163-009-11
1-163-123-00
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
22PF
22PF
0.001uF
180PF
5%
5%
10%
5%
25V
50V
50V
50V
50V
C181
C182
1-163-009-11 CERAMIC CHIP
1-163-123-00 CERAMIC CHIP
0.001uF
180PF
10%
5%
50V
50V
< CONNECTOR >
R871
1-249-441-11 CARBON
100K
5%
1/4W
R872
1-249-429-11 CARBON
10K
5%
1/4W
R873
1-249-439-11 CARBON
68K
5%
1/4W
R874
1-249-437-11 CARBON
47K
5%
1/4W
**************************************************************
A-4724-375-A BD (CD) BOARD, COMPLETE
***********************
*
CN101
CN102
< FERRITE BEAD/SHORT >
FB101
FB102
FB103
FB104
< CAPACITOR >
1-778-874-11 CONNECTOR, FFC (LIF (NON-ZIF)) 19P
1-777-937-11 CONNECTOR, FFC/FPC 16P
1-500-445-21
1-216-295-11
1-500-445-21
1-216-295-11
FERRITE
SHORT
FERRITE
SHORT
0uH
0
0uH
0
C101
C102
C103
C104
C108
1-163-005-11
1-164-004-11
1-163-005-11
1-163-009-11
1-164-004-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
470PF
0.1uF
470PF
0.001uF
0.1uF
10%
10%
10%
10%
10%
50V
25V
50V
50V
25V
C109
C110
C111
C112
C113
1-163-011-11
1-164-182-11
1-163-251-11
1-163-038-11
1-163-038-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.0015uF 10%
0.0033uF 10%
100PF
5%
0.1uF
0.1uF
50V
50V
50V
25V
25V
Q101
C114
C115
C116
C117
C118
1-163-038-11
1-126-607-11
1-126-607-11
1-126-209-11
1-163-009-11
CERAMIC CHIP
ELECT CHIP
ELECT CHIP
ELECT CHIP
CERAMIC CHIP
0.1uF
47uF
47uF
100uF
0.001uF
25V
4V
4V
4V
50V
R101
R102
R103
R104
R105
1-216-077-00
1-216-097-11
1-216-077-00
1-216-085-00
1-216-073-00
RES-CHIP
RES-CHIP
RES-CHIP
METAL CHIP
METAL CHIP
15K
100K
15K
33K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
C119
C121
C122
C123
C124
1-163-235-11
1-163-038-11
1-126-206-11
1-163-021-11
1-107-823-11
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
22PF
0.1uF
100uF
0.01uF
0.47uF
50V
25V
6.3V
50V
16V
R106
R107
R108
R109
R110
1-216-049-11
1-216-073-00
1-216-061-00
1-216-121-11
1-216-025-11
RES-CHIP
METAL CHIP
METAL CHIP
RES-CHIP
RES-CHIP
1K
10K
3.3K
1M
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
C125
C126
C127
C128
C129
1-163-038-11
1-163-038-11
1-128-065-11
1-163-038-11
1-163-031-11
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
68uF
0.1uF
0.01uF
25V
25V
10V
25V
50V
R111
R113
R114
R116
R117
1-216-121-11
1-216-121-11
1-216-073-00
1-216-001-00
1-216-049-11
RES-CHIP
RES-CHIP
METAL CHIP
METAL CHIP
RES-CHIP
1M
1M
10K
10
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
C130
C131
C133
C140
C141
1-164-346-11
1-124-779-00
1-125-838-11
1-164-346-11
1-164-346-11
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
1uF
10uF
2.2uF
1uF
1uF
16V
16V
6.3V
16V
16V
R119
R123
R124
R131
R135
1-216-041-00
1-216-073-00
1-216-097-11
1-216-033-00
1-216-295-11
METAL CHIP
METAL CHIP
RES-CHIP
METAL CHIP
SHORT
470
10K
100K
220
0
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
C143
C151
C153
C154
C156
1-163-038-11
1-163-235-11
1-163-038-11
1-110-501-11
1-163-235-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
22PF
0.1uF
0.33uF
22PF
25V
50V
25V
16V
50V
R136
R137
R138
R143
R144
1-216-295-11
1-216-295-11
1-216-295-11
1-216-103-00
1-216-103-00
SHORT
SHORT
SHORT
METAL CHIP
METAL CHIP
0
0
0
180K
180K
5%
5%
1/10W
1/10W
The components identified by mark 0 or dotted
line with mark 0 are critical for safety.
Replace only with part number specified.
20%
20%
20%
10%
5%
20%
10%
10%
20%
20%
10%
5%
10%
5%
< IC >
IC101
IC102
IC103
8-752-386-85 IC CXD2587Q
8-759-549-28 IC BA5974FP-E2
8-752-085-51 IC CXA2568M-T6
< TRANSISTOR >
8-729-010-08 TRANSISTOR
MSB710-R
< RESISTOR >
87
BD (CD)
Ref. No.
BD (MD)
Part No.
Description
R147
R148
R149
R158
R159
1-216-069-00
1-216-001-00
1-216-001-00
1-216-111-00
1-216-101-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
6.8K
10
10
390K
150K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
Remark
R161
R162
R171
R172
R173
1-216-308-00
1-216-101-00
1-216-078-00
1-216-073-00
1-216-077-00
METAL CHIP
METAL CHIP
RES-CHIP
METAL CHIP
RES-CHIP
4.7
150K
16K
10K
15K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R181
R182
R183
1-216-078-00 RES-CHIP
1-216-073-00 METAL CHIP
1-216-077-00 RES-CHIP
16K
10K
15K
5%
5%
5%
1/10W
1/10W
1/10W
< NETWORK RESISTOR >
RN101
RN102
1-233-576-11 RES, CHIP NETWORK 100
1-233-576-11 RES, CHIP NETWORK 100
< SWITCH >
S101
1-572-085-11 SWITCH, LEAF (LIMIT)
Ref. No.
Part No.
Description
Remark
C135
1-163-038-11 CERAMIC CHIP
0.1uF
25V
C136
C142
C143
C144
C146
1-126-206-11
1-163-251-11
1-163-251-11
1-163-251-11
1-163-038-11
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100uF
100PF
100PF
100PF
0.1uF
20%
5%
5%
5%
6.3V
50V
50V
50V
25V
C151
C152
C153
C156
C158
1-126-206-11
1-163-038-11
1-163-021-11
1-163-038-11
1-163-019-00
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100uF
20%
0.1uF
0.01uF
10%
0.1uF
0.0068uF 10%
6.3V
25V
50V
25V
50V
C160
C161
C163
C164
C167
1-104-601-11
1-104-601-11
1-163-021-11
1-163-021-11
1-163-038-11
ELECT CHIP
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
10uF
10uF
0.01uF
0.01uF
0.1uF
10V
10V
50V
50V
25V
C168
C169
C171
C181
C183
1-163-038-11
1-125-822-11
1-163-038-11
1-104-913-11
1-163-038-11
CERAMIC CHIP
TANTALUM
CERAMIC CHIP
TANTALUM CHIP
CERAMIC CHIP
0.1uF
10uF
0.1uF
10uF
0.1uF
C184
C185
C187
C188
C189
1-117-970-11
1-164-611-11
1-104-913-11
1-163-021-11
1-163-989-11
ELECT CHIP
CERAMIC CHIP
TANTALUM CHIP
CERAMIC CHIP
CERAMIC CHIP
22uF
0.001uF
10uF
0.01uF
0.033uF
20%
10%
20%
10%
10%
10V
500V
16V
50V
25V
C190
C191
C196
C197
1-126-206-11
1-163-038-11
1-163-038-11
1-163-038-11
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100uF
0.1uF
0.1uF
0.1uF
20%
6.3V
25V
25V
25V
20%
20%
10%
10%
20%
20%
25V
10V
25V
16V
25V
< VIBRATOR >
X101
1-767-408-21 VIBRATOR, CRYSTAL (16.9344MHz)
**************************************************************
A-4699-893-A BD (MD) BOARD, COMPLETE
************************
< CAPACITOR >
C101
C102
C103
C104
C105
1-125-822-11
1-163-038-11
1-125-822-11
1-125-822-11
1-163-021-11
TANTALUM
CERAMIC CHIP
TANTALUM
TANTALUM
CERAMIC CHIP
10uF
0.1uF
10uF
10uF
0.01uF
20%
C106
C107
C108
C109
C111
1-163-275-11
1-163-038-11
1-163-038-11
1-163-037-11
1-164-344-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.001uF
0.1uF
0.1uF
0.022uF
0.068uF
10%
10%
50V
25V
25V
25V
25V
C112
C113
C115
C116
C117
1-163-017-00
1-109-982-11
1-164-489-11
1-163-037-11
1-163-809-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.0047uF
1uF
0.22uF
0.022uF
0.047uF
5%
10%
10%
10%
10%
50V
10V
16V
25V
25V
D101
D181
D183
C118
C119
C121
C122
C123
1-163-038-11
1-125-822-11
1-125-822-11
1-163-021-11
1-163-038-11
CERAMIC CHIP
TANTALUM
TANTALUM
CERAMIC CHIP
CERAMIC CHIP
0.1uF
10uF
10uF
0.01uF
0.1uF
20%
20%
10%
25V
10V
10V
50V
25V
IC101
IC103
IC121
IC123
IC124
8-752-080-95
8-729-903-10
8-752-389-44
8-759-096-87
8-759-334-38
IC CXA2523AR
TRANSISTOR FMW1-T-148
IC CXD2654R
IC TC7WU04FU (TE12R)
IC MSM51V4400-70TS-K
C124
C127
C128
C129
C130
1-163-038-11
1-163-038-11
1-163-021-11
1-107-823-11
1-163-251-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.01uF
0.47uF
100PF
10%
10%
5%
25V
25V
50V
16V
50V
IC152
IC171
IC181
IC192
8-759-430-25
8-759-640-39
8-759-481-17
8-759-460-72
IC
IC
IC
IC
C131
C132
C133
C134
1-163-023-00
1-107-823-11
1-163-017-00
1-163-038-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.015uF 5%
0.47uF
10%
0.0047uF 5%
0.1uF
50V
16V
50V
25V
20%
20%
10%
5%
10V
25V
10V
10V
50V
< CONNECTOR >
CN101
CN102
CN103
CN104
CN110
1-569-479-51
1-784-833-21
1-784-834-21
1-770-687-11
1-695-440-21
CONNECTOR, FPC 21P
CONNECTOR, FFC (LIF (NON-ZIF)) 21P
CONNECTOR, FFC (LIF (NON-ZIF)) 23P
CONNECTOR, FFC/FPC 4P
PIN, CONNECTOR (PC BOARD) 6P
< DIODE >
8-719-988-61 DIODE 1SS355TE-17
8-719-046-86 DIODE F1J6TP
8-719-046-86 DIODE F1J6TP
< IC/TRANSISTOR >
BH6511FS
BR24C02F-WE2
MC74ACT08DTR2
BA033FP-E2
< COIL/SHORT >
88
L101
L102
L103
1-414-813-11 FERRITE
1-414-813-11 FERRITE
1-414-813-11 FERRITE
0uH
0uH
0uH
BD (MD)
Ref. No.
Part No.
Description
Remark
L105
L106
1-414-813-11 FERRITE
1-414-813-11 FERRITE
0uH
0uH
L121
L122
L151
L152
L153
1-414-813-11
1-414-813-11
1-412-029-11
1-412-029-11
1-412-032-11
FERRITE
FERRITE
INDUCTOR CHIP
INDUCTOR CHIP
INDUCTOR CHIP
0uH
0uH
10uH
10uH
100uH
L154
L161
L162
L181
1-412-032-11
1-414-813-11
1-414-813-11
1-216-295-11
INDUCTOR CHIP
FERRITE
FERRITE
SHORT
100uH
0uH
0uH
0
< TRANSISTOR >
Q101
Q102
Q103
Q104
Q162
8-729-028-91
8-729-026-53
8-729-028-99
8-729-028-99
8-729-101-07
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
Q163
Q181
Q182
8-729-028-91 TRANSISTOR
8-729-018-75 FET
8-729-017-65 FET
RT1P441M-TP-1
2SA1576A-T106-QR
RT1N144M-TP-1
RT1N144M-TP-1
2SB798-T1DK
RT1P441M-TP-1
2SJ278MYTR
2SK1764KYTR
< RESISTOR >
R103
R104
R105
R106
R107
1-216-049-11
1-216-073-00
1-216-065-00
1-216-133-00
1-216-113-00
RES-CHIP
METAL CHIP
RES-CHIP
METAL CHIP
METAL CHIP
1K
10K
4.7K
3.3M
470K
R109
R110
R111
R112
R113
1-216-295-11
1-216-073-00
1-216-295-11
1-216-089-11
1-216-049-11
SHORT
METAL CHIP
SHORT
RES-CHIP
RES-CHIP
0
10K
0
47K
1K
R115
R117
R120
R121
R123
1-216-049-11
1-216-113-00
1-216-025-11
1-216-097-11
1-216-295-11
RES-CHIP
METAL CHIP
RES-CHIP
RES-CHIP
SHORT
R124
R125
R127
R129
R130
1-216-025-11
1-216-025-11
1-216-025-11
1-216-295-11
1-216-295-11
R131
R132
R133
R134
R135
Ref. No.
Part No.
Description
R149
R150
R151
R152
R158
1-216-073-00
1-216-295-11
1-216-073-00
1-216-073-00
1-216-097-11
METAL CHIP
SHORT
METAL CHIP
METAL CHIP
RES-CHIP
10K
0
10K
10K
100K
R159
R160
R161
R162
R163
1-216-097-11
1-216-295-11
1-216-057-00
1-216-057-00
1-216-057-00
RES-CHIP
SHORT
METAL CHIP
METAL CHIP
METAL CHIP
R164
R165
R166
R167
R169
1-216-045-00
1-216-097-11
1-216-298-00
1-216-065-00
1-219-724-11
R170
R171
R173
R175
R177
LOADING
Remark
5%
1/10W
5%
5%
5%
1/10W
1/10W
1/10W
100K
0
2.2K
2.2K
2.2K
5%
1/10W
5%
5%
5%
1/10W
1/10W
1/10W
METAL CHIP
RES-CHIP
METAL CHIP
RES-CHIP
METAL CHIP
680
100K
2.2
4.7K
1
5%
5%
5%
5%
1%
1/10W
1/10W
1/10W
1/10W
1/4W
1-216-073-00
1-216-073-00
1-216-121-11
1-216-065-00
1-216-061-00
METAL CHIP
METAL CHIP
RES-CHIP
RES-CHIP
METAL CHIP
10K
10K
1M
4.7K
3.3K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R179
R180
R182
R183
R184
1-216-085-00
1-216-073-00
1-216-089-11
1-216-089-11
1-216-073-00
METAL CHIP
METAL CHIP
RES-CHIP
RES-CHIP
METAL CHIP
33K
10K
47K
47K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R185
R186
R188
R189
R190
1-216-081-00
1-216-089-11
1-216-073-00
1-216-073-00
1-216-073-00
METAL CHIP
RES-CHIP
METAL CHIP
METAL CHIP
METAL CHIP
22K
47K
10K
10K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R195
R196
R197
R198
1-216-073-00
1-216-295-11
1-216-295-11
1-216-296-00
METAL CHIP
SHORT
SHORT
SHORT
10K
0
0
0
5%
1/10W
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
5%
1/10W
5%
5%
1/10W
1/10W
1K
470K
100
100K
0
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
RES-CHIP
RES-CHIP
RES-CHIP
SHORT
SHORT
100
100
100
0
0
5%
5%
5%
1-216-073-00
1-216-097-11
1-216-117-00
1-216-049-11
1-216-061-00
METAL CHIP
RES-CHIP
METAL CHIP
RES-CHIP
METAL CHIP
10K
100K
680K
1K
3.3K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
* CN151
R136
R137
R140
R142
R143
1-216-049-11
1-216-295-11
1-216-029-00
1-216-073-00
1-216-073-00
RES-CHIP
SHORT
METAL CHIP
METAL CHIP
METAL CHIP
1K
0
150
10K
10K
5%
1/10W
S1
5%
5%
5%
1/10W
1/10W
1/10W
R144
R145
R146
R147
R148
1-216-025-11
1-216-073-00
1-216-037-00
1-216-025-11
1-216-045-00
RES-CHIP
METAL CHIP
METAL CHIP
RES-CHIP
METAL CHIP
100
10K
330
100
680
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
< SWITCH >
S101
S102
1/10W
1/10W
1/10W
1-762-596-21 SWITCH, PUSH (1 KEY) (LIMIT)
1-762-148-21 SWITCH, PUSH (2 KEY)
(PROTECT/REFLECT RATE DETECT)
**************************************************************
1-674-336-12 LOADING BOARD
**************
< CONNECTOR >
1-568-943-11 PIN, CONNECTOR 5P
< SWITCH >
1-771-799-11 SWITCH, LEVER (SLIDE)
(CD TRAY OPEN/CLOSE DETECT)
**************************************************************
89
MAIN
Ref. No.
Part No.
Description
Remark
A-4475-919-A MAIN BOARD, COMPLETE (HK, TW)
A-4475-923-A MAIN BOARD, COMPLETE (KR)
*********************
Ref. No.
Part No.
Description
C363
C364
C365
C366
1-126-957-11
1-130-473-00
1-124-721-11
1-136-165-00
ELECT
MYLAR
ELECT
FILM
0.22uF
0.0015uF
10uF
0.1uF
20%
5%
20%
5%
50V
50V
50V
50V
Remark
C367
C501
C502
C503
C504
1-136-165-00
1-164-025-51
1-164-025-51
1-162-306-11
1-162-306-11
FILM
CERAMIC
CERAMIC
CERAMIC
CERAMIC
0.1uF
18PF
18PF
0.01uF
0.01uF
5%
5%
5%
30%
30%
50V
50V
50V
16V
16V
C505
C506
C507
C508
C521
1-164-159-11
1-162-306-11
1-126-933-11
1-162-282-31
1-164-159-11
CERAMIC
CERAMIC
ELECT
CERAMIC
CERAMIC
0.1uF
0.01uF
100uF
100PF
0.1uF
30%
20%
10%
50V
16V
16V
50V
50V
C901
C902
C903
C904
C905
1-124-721-11
1-124-721-11
1-124-721-11
1-126-964-11
1-126-926-11
ELECT
ELECT
ELECT
ELECT
ELECT
10uF
10uF
10uF
10uF
1000uF
20%
20%
20%
20%
20%
50V
50V
50V
50V
10V
C906
C911
C912
C913
C914
1-124-721-11
1-126-052-11
1-124-721-11
1-126-964-11
1-126-926-11
ELECT
ELECT
ELECT
ELECT
ELECT
10uF
100uF
10uF
10uF
1000uF
20%
20%
20%
20%
20%
50V
50V
50V
50V
10V
C915
C916
C917
C921
C922
1-126-964-11
1-126-926-11
1-126-933-11
1-126-964-11
1-126-926-11
ELECT
ELECT
ELECT
ELECT
ELECT
10uF
1000uF
100uF
10uF
1000uF
20%
20%
20%
20%
20%
50V
10V
16V
50V
10V
C923
C931
C932
C933
C934
1-126-933-11
1-126-933-11
1-126-960-11
1-164-159-11
1-162-306-11
ELECT
ELECT
ELECT
CERAMIC
CERAMIC
100uF
100uF
1uF
0.1uF
0.01uF
20%
20%
20%
16V
16V
50V
50V
16V
C935
C941
C942
C943
C945
1-164-159-11
1-126-947-11
1-164-159-11
1-164-159-11
1-164-159-11
CERAMIC
ELECT
CERAMIC
CERAMIC
CERAMIC
0.1uF
47uF
0.1uF
0.1uF
0.1uF
7-685-646-79 SCREW +BVTP 3X8 TYPE2 N-S
< CAPACITOR >
BT922
C101
C102
C103
C141
1-125-623-11
1-162-282-31
1-162-294-31
1-126-964-11
1-126-933-11
DOUBLE LAYER
CERAMIC
CERAMIC
ELECT
ELECT
0.22F
100PF
0.001uF
10uF
100uF
10%
10%
20%
20%
5.5V
50V
50V
50V
16V
C142
C143
C144
C145
C151
1-126-933-11
1-126-933-11
1-126-964-11
1-126-964-11
1-162-282-31
ELECT
ELECT
ELECT
ELECT
CERAMIC
100uF
100uF
10uF
10uF
100PF
20%
20%
20%
20%
10%
16V
16V
50V
50V
50V
C152
C153
C161
C166
C167
1-162-294-31
1-126-964-11
1-126-933-11
1-162-290-31
1-162-294-31
CERAMIC
ELECT
ELECT
CERAMIC
CERAMIC
0.001uF
10uF
100uF
470PF
0.001uF
10%
20%
20%
10%
10%
50V
50V
16V
50V
50V
C168
C169
C171
C172
C173
1-162-282-31
1-162-282-31
1-164-159-11
1-162-306-11
1-126-933-11
CERAMIC
CERAMIC
CERAMIC
CERAMIC
ELECT
100PF
100PF
0.1uF
0.01uF
100uF
10%
10%
30%
20%
50V
50V
50V
16V
16V
C174
C175
C301
C302
C303
1-164-159-11
1-164-159-11
1-126-964-11
1-162-302-11
1-126-964-11
CERAMIC
CERAMIC
ELECT
CERAMIC
ELECT
0.1uF
0.1uF
10uF
20%
0.0022uF 30%
10uF
20%
50V
50V
50V
16V
50V
C304
C305
C306
C307
C310
1-130-475-00
1-124-721-11
1-162-302-11
1-126-964-11
1-162-294-31
MYLAR
ELECT
CERAMIC
ELECT
CERAMIC
0.0022uF
10uF
0.0022uF
10uF
0.001uF
5%
20%
30%
20%
10%
50V
50V
16V
50V
50V
C311
C312
C313
C314
C315
1-124-721-11
1-136-165-00
1-126-957-11
1-130-473-00
1-124-721-11
ELECT
FILM
ELECT
MYLAR
ELECT
10uF
0.1uF
0.22uF
0.0015uF
10uF
20%
5%
20%
5%
20%
50V
50V
50V
50V
50V
C316
C317
C323
C324
C325
1-136-165-00
1-136-165-00
1-124-721-11
1-124-724-11
1-130-477-00
FILM
FILM
ELECT
ELECT
MYLAR
0.1uF
0.1uF
10uF
47uF
0.0033uF
5%
5%
20%
20%
5%
50V
50V
50V
50V
50V
C326
C351
C352
C353
C354
1-162-286-31
1-126-964-11
1-162-302-11
1-126-964-11
1-130-475-00
CERAMIC
ELECT
CERAMIC
ELECT
MYLAR
220PF
10uF
0.0022uF
10uF
0.0022uF
10%
20%
30%
20%
5%
50V
50V
16V
50V
50V
C355
C356
C357
C360
C361
1-124-721-11
1-162-302-11
1-126-964-11
1-162-294-31
1-124-721-11
ELECT
CERAMIC
ELECT
CERAMIC
ELECT
10uF
0.0022uF
10uF
0.001uF
10uF
20%
30%
20%
10%
20%
50V
16V
50V
50V
50V
D171
D901
D911
D912
D913
8-719-947-13
8-719-024-99
8-719-024-99
8-719-911-19
8-719-911-19
C362
1-136-165-00 FILM
0.1uF
5%
50V
D914
8-719-911-19 DIODE 1SS119-25
90
30%
20%
50V
35V
50V
50V
50V
< CONNECTOR >
* CN101
* CN102
CN103
CN105
CN106
1-766-955-11
1-566-856-11
1-770-731-11
1-784-776-11
1-568-683-11
CONNECTOR, BOARD TO BOARD 11P
SOCKET, CONNECTOR 5P (TAPE CONTROL)
CONNECTOR, BOARD TO BOARD 12P
CONNECTOR, FFC 15P
PIN, CONNECTOR (PC BAORD) 2P
CN107
CN109
* CN110
CN111
1-784-786-11
1-784-780-11
1-568-954-11
1-568-844-11
CONNECTOR, FFC 25P
CONNECTOR, FFC 19P
PIN, CONNECTOR 5P
CONNECTOR, FFC 29P
< DIODE >
DIODE
DIODE
DIODE
DIODE
DIODE
MTZJ-T-72-4.7B
11ES2-NTA2B
11ES2-NTA2B
1SS119-25
1SS119-25
MAIN
Ref. No.
Part No.
Description
D921
D922
D923
D924
8-719-024-99
8-719-911-19
8-719-911-19
8-719-911-19
DIODE
DIODE
DIODE
DIODE
11ES2-NTA2B
1SS119-25
1SS119-25
1SS119-25
Remark
D941
D942
D943
D946
8-719-911-19
8-719-911-19
8-719-911-19
8-719-911-19
DIODE
DIODE
DIODE
DIODE
1SS119-25
1SS119-25
1SS119-25
1SS119-25
< GROUND TERMINAL >
EP1
EP2
1-537-770-21 TERMINAL BOARD, GROUND
1-537-770-21 TERMINAL BOARD, GROUND
< IC >
IC171
IC301
IC501
IC901
IC902
8-759-822-09
8-759-494-40
8-759-675-41
8-759-394-35
8-759-604-86
IC
IC
IC
IC
IC
LB1641
M62428AFP600C
M30620MCA-A51FP
BA12T
M5F7807L
IC903
IC911
IC912
IC913
IC921
8-759-450-49
8-759-647-11
8-759-445-59
8-759-647-11
8-759-647-11
IC
IC
IC
IC
IC
BA07T
uPC2905HF
BA033T
uPC2905HF
uPC2905HF
IC931
IC941
8-759-481-02 IC M62016L
8-759-637-58 IC PST592C-T
< JACK >
J101
1-779-653-12 JACK, PIN (TAPE IN/OUT)
Ref. No.
Part No.
Description
Remark
R132
R141
R151
R152
R153
1-247-807-31
1-249-417-11
1-249-441-11
1-249-417-11
1-249-429-11
CARBON
CARBON
CARBON
CARBON
CARBON
100
1K
100K
1K
10K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R154
R155
R156
R171
R172
1-249-417-11
1-249-441-11
1-249-441-11
1-249-409-11
1-249-414-11
CARBON
CARBON
CARBON
CARBON
CARBON
1K
100K
100K
220
560
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R302
R303
R304
R306
R309
1-247-843-11
1-249-441-11
1-249-417-11
1-249-417-11
1-249-437-11
CARBON
CARBON
CARBON
CARBON
CARBON
3.3K
100K
1K
1K
47K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R312
R313
R314
R315
R316
1-249-424-11
1-247-885-00
1-249-433-11
1-247-903-00
1-249-441-11
CARBON
CARBON
CARBON
CARBON
CARBON
3.9K
180K
22K
1M
100K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R321
R322
R323
R324
R325
1-249-435-11
1-247-903-00
1-249-417-11
1-249-417-11
1-249-417-11
CARBON
CARBON
CARBON
CARBON
CARBON
33K
1M
1K
1K
1K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R326
R352
R353
R354
R356
1-249-413-11
1-247-843-11
1-249-441-11
1-249-417-11
1-249-417-11
CARBON
CARBON
CARBON
CARBON
CARBON
470
3.3K
100K
1K
1K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R359
R362
R363
R364
R365
1-249-437-11
1-249-424-11
1-247-885-00
1-249-433-11
1-247-903-00
CARBON
CARBON
CARBON
CARBON
CARBON
47K
3.9K
180K
22K
1M
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R366
R391
R501
R502
R505
1-249-441-11
1-247-830-11
1-247-807-31
1-249-417-11
1-249-437-11
CARBON
CARBON
CARBON
CARBON
CARBON
100K
910
100
1K
47K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R506
R507
R508
R509
R510
1-249-417-11
1-247-807-31
1-247-807-31
1-247-807-31
1-249-417-11
CARBON
CARBON
CARBON
CARBON
CARBON
1K
100
100
100
1K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R511
R512
R513
R514
R515
1-247-807-31
1-247-807-31
1-247-807-31
1-247-807-31
1-247-807-31
CARBON
CARBON
CARBON
CARBON
CARBON
100
100
100
100
100
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R516
R517
R518
R519
R520
1-247-807-31
1-247-807-31
1-247-807-31
1-249-417-11
1-249-417-11
CARBON
CARBON
CARBON
CARBON
CARBON
100
100
100
1K
1K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R521
R522
1-247-807-31 CARBON
1-247-807-31 CARBON
100
100
5%
5%
1/4W
1/4W
< TRANSISTOR >
Q101
Q102
Q111
Q112
Q151
8-729-620-05
8-729-900-63
8-729-048-96
8-729-048-96
8-729-620-05
TRANSISTOR
TRANSISTOR
FET
FET
TRANSISTOR
2SC2603-EF
DTA124ES
2SK1825
2SK1825
2SC2603-EF
Q301
Q351
Q501
Q551
Q552
8-729-620-05
8-729-620-05
8-729-422-73
8-729-422-73
8-729-900-63
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SC2603-EF
2SC2603-EF
UN4212
UN4212
DTA124ES
Q911
Q912
Q921
Q931
Q941
8-729-118-01
8-729-422-73
8-729-620-05
8-729-620-05
8-729-620-05
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SB1116-K
UN4212
2SC2603-EF
2SC2603-EF
2SC2603-EF
< RESISTOR >
R101
R102
R103
R104
R105
1-249-441-11
1-249-417-11
1-249-429-11
1-249-417-11
1-249-441-11
CARBON
CARBON
CARBON
CARBON
CARBON
100K
1K
10K
1K
100K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R106
R111
R112
R113
R114
1-249-441-11
1-249-393-11
1-249-393-11
1-249-437-11
1-249-441-11
CARBON
CARBON
CARBON
CARBON
CARBON
100K
10
10
47K
100K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
91
MAIN
Ref. No.
MD DIGITAL
Part No.
Description
Remark
R523
R524
R525
1-249-417-11 CARBON
1-247-807-31 CARBON
1-249-417-11 CARBON
1K
100
1K
5%
5%
5%
1/4W
1/4W
1/4W
R526
R527
R528
R529
R530
1-247-807-31
1-247-807-31
1-247-807-31
1-247-807-31
1-247-807-31
CARBON
CARBON
CARBON
CARBON
CARBON
100
100
100
100
100
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R531
R532
R533
R534
R535
1-249-417-11
1-249-417-11
1-249-417-11
1-249-417-11
1-249-417-11
CARBON
CARBON
CARBON
CARBON
CARBON
1K
1K
1K
1K
1K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R536
R537
R538
R539
R540
1-249-417-11
1-249-417-11
1-249-417-11
1-249-417-11
1-249-417-11
CARBON
CARBON
CARBON
CARBON
CARBON
1K
1K
1K
1K
1K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R541
R542
R543
R544
R545
1-249-417-11
1-249-417-11
1-249-417-11
1-249-417-11
1-249-417-11
CARBON
CARBON
CARBON
CARBON
CARBON
1K
1K
1K
1K
1K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R547
R548
R549
R550
R551
1-247-807-31
1-247-807-31
1-247-807-31
1-247-807-31
1-249-437-11
CARBON
CARBON
CARBON
CARBON
CARBON
100
100
100
100
47K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R552
R553
R554
R555
R556
1-249-429-11
1-249-417-11
1-249-417-11
1-249-429-11
1-249-429-11
CARBON
CARBON
CARBON
CARBON
CARBON
10K
1K
1K
10K
10K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R557
R558
R559
R560
R561
1-249-429-11
1-249-429-11
1-249-429-11
1-249-427-11
1-249-427-11
CARBON
CARBON
CARBON
CARBON
CARBON
10K
10K
10K
6.8K
6.8K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R562
R563
R564
R565
R566
1-249-427-11
1-249-417-11
1-249-417-11
1-249-412-11
1-249-426-11
CARBON
CARBON
CARBON
CARBON
CARBON
6.8K
1K
1K
390
5.6K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R567
R568
R569
R570
R573
1-247-843-11
1-249-429-11
1-249-429-11
1-249-429-11
1-247-807-31
CARBON
CARBON
CARBON
CARBON
CARBON
3.3K
10K
10K
10K
100
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R591
R592
R911
R921
R922
1-249-425-11
1-249-425-11
1-249-409-11
1-247-807-31
1-249-429-11
CARBON
CARBON
CARBON
CARBON
CARBON
4.7K
4.7K
220
100
10K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R923
R925
R926
R931
R932
1-249-433-11
1-249-411-11
1-249-385-11
1-247-887-00
1-249-441-11
CARBON
CARBON
CARBON
CARBON
CARBON
22K
330
2.2
220K
100K
5%
5%
5%
5%
5%
1/4W
1/4W
1/6W
1/4W
1/4W
92
Ref. No.
Part No.
Description
Remark
R933
R941
R942
R943
R946
1-249-433-11
1-249-413-11
1-249-429-11
1-249-437-11
1-249-433-11
CARBON
CARBON
CARBON
CARBON
CARBON
22K
470
10K
47K
22K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R947
R949
1-249-437-11 CARBON
1-249-429-11 CARBON
47K
10K
5%
5%
1/4W
1/4W
< VIBRATOR >
X501
1-781-107-21 VIBRATOR, SERAMIC (16MHz)
X502
1-567-098-41 VIBRATOR, CRYSTAL (32.768kHz)
**************************************************************
A-4475-917-A MD DIGITAL BOARD, COMPLETE
**************************
< CAPACITOR >
C171
C172
C201
C202
C203
1-163-038-11
1-126-206-11
1-163-234-11
1-163-229-11
1-163-021-11
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
100uF
20PF
12PF
0.01uF
C216
C341
C342
C343
C350
1-126-205-11
1-126-205-11
1-126-206-11
1-126-205-11
1-163-038-11
ELECT CHIP
ELECT CHIP
ELECT CHIP
ELECT CHIP
CERAMIC CHIP
47uF
47uF
100uF
47uF
0.1uF
C351
C352
C353
C355
C357
1-163-038-11
1-126-205-11
1-163-038-11
1-163-251-11
1-163-021-11
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
47uF
0.1uF
100PF
0.01uF
C358
C359
C360
C362
C363
1-163-251-11
1-163-251-11
1-163-251-11
1-163-038-11
1-163-251-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100PF
100PF
100PF
0.1uF
100PF
5%
5%
5%
C503
C509
C510
C522
C527
1-126-206-11
1-126-206-11
1-126-206-11
1-163-038-11
1-163-038-11
ELECT CHIP
ELECT CHIP
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
100uF
100uF
100uF
0.1uF
0.1uF
20%
20%
20%
C528
C529
C2001
1-163-038-11 CERAMIC CHIP
1-163-038-11 CERAMIC CHIP
1-163-125-00 CERAMIC CHIP
0.1uF
0.1uF
220PF
20%
5%
5%
10%
20%
20%
20%
20%
20%
5%
10%
5%
5%
25V
6.3V
50V
50V
50V
6.3V
6.3V
6.3V
6.3V
25V
25V
6.3V
25V
50V
50V
50V
50V
50V
25V
50V
6.3V
6.3V
6.3V
25V
25V
25V
25V
50V
< CONNECTOR >
CN101
CN102
CN103
CN104
1-793-311-11
1-784-687-41
1-784-834-21
1-784-833-21
CONNECTOR, FFC (LIF (NON-ZIF)) 25P
PIN, CONNECTOR (PC BOARD) 7P
CONNECTOR, FFC (LIF (NON-ZIF)) 23P
CONNECTOR, FFC (LIF (NON-ZIF)) 21P
< IC >
IC153
IC201
IC202
IC316
8-759-481-19
8-759-553-65
8-759-564-53
8-759-657-09
IC
IC
IC
IC
LB1830M-S-TE-L
UDA1341TS
MC74HCU04ADTR2
M30624MG-A16FP
MD DIGITAL
Ref. No.
Part No.
Description
Remark
Ref. No.
Part No.
1-424-675-11 INDUCTOR
1-500-445-21 FERRITE
1-500-445-21 FERRITE
8-729-028-99 TRANSISTOR
Remark
33uH
0uH
0uH
C601
C602
C603
C604
C605
1-162-306-11
1-162-306-11
1-124-261-00
1-162-306-11
1-162-306-11
CERAMIC
CERAMIC
ELECT
CERAMIC
CERAMIC
0.01uF
0.01uF
10uF
0.01uF
0.01uF
30%
30%
20%
30%
30%
16V
16V
50V
16V
16V
RT1N144M-TP-1
C606
C623
C635
C636
C640
1-162-306-11
1-162-306-11
1-126-964-11
1-128-551-11
1-162-282-31
CERAMIC
CERAMIC
ELECT
ELECT
CERAMIC
0.01uF
0.01uF
10uF
22uF
100PF
30%
30%
20%
20%
10%
16V
16V
50V
25V
50V
C648
C649
C650
C651
C652
1-162-286-21
1-162-286-21
1-162-286-21
1-162-286-21
1-162-286-21
CERAMIC
CERAMIC
CERAMIC
CERAMIC
CERAMIC
220PF
220PF
220PF
220PF
220PF
10%
10%
10%
10%
10%
50V
50V
50V
50V
50V
C653
C654
C655
C656
C657
1-162-286-21
1-162-286-21
1-162-286-21
1-162-286-21
1-162-286-21
CERAMIC
CERAMIC
CERAMIC
CERAMIC
CERAMIC
220PF
220PF
220PF
220PF
220PF
10%
10%
10%
10%
10%
50V
50V
50V
50V
50V
C658
C659
C660
C661
C662
1-162-286-21
1-162-286-21
1-162-286-21
1-162-286-21
1-162-286-21
CERAMIC
CERAMIC
CERAMIC
CERAMIC
CERAMIC
220PF
220PF
220PF
220PF
220PF
10%
10%
10%
10%
10%
50V
50V
50V
50V
50V
C664
C665
C671
C672
C673
1-124-261-00
1-104-664-11
1-162-294-31
1-162-294-31
1-164-159-21
ELECT
ELECT
CERAMIC
CERAMIC
CERAMIC
10uF
47uF
0.001uF
0.001uF
0.1uF
20%
20%
10%
10%
50V
16V
50V
50V
50V
C674
1-162-294-31 CERAMIC
0.001uF
10%
50V
< TRANSISTOR >
Q350
Description
< CAPACITOR >
< COIL >
L181
L201
L202
PANEL
< RESISTOR >
R201
R202
R203
R204
R205
1-216-121-11
1-216-041-00
1-216-049-11
1-216-089-11
1-216-113-00
RES-CHIP
METAL CHIP
RES-CHIP
RES-CHIP
METAL CHIP
1M
470
1K
47K
470K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R207
R210
R330
R331
R333
1-216-025-11
1-216-041-00
1-216-073-00
1-216-097-11
1-216-073-00
RES-CHIP
METAL CHIP
METAL CHIP
RES-CHIP
METAL CHIP
100
470
10K
100K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R349
R351
R352
R353
R358
1-216-073-00
1-216-057-00
1-216-053-00
1-216-053-00
1-216-073-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
2.2K
1.5K
1.5K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R361
R363
R366
R367
R370
1-216-073-00
1-216-073-00
1-216-097-11
1-216-097-11
1-216-073-00
METAL CHIP
METAL CHIP
RES-CHIP
RES-CHIP
METAL CHIP
10K
10K
100K
100K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R383
R384
R385
R386
R391
1-216-073-00
1-216-073-00
1-216-073-00
1-216-073-00
1-216-073-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
10K
10K
10K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R395
R400
R816
R817
R818
1-216-073-00
1-216-073-00
1-216-174-00
1-216-174-00
1-216-174-00
METAL CHIP
METAL CHIP
RES-CHIP
RES-CHIP
RES-CHIP
10K
10K
100
100
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/8W
1/8W
1/8W
R819
R2002
R2004
R2005
R2006
1-216-174-00
1-216-073-00
1-216-041-00
1-216-025-11
1-216-025-11
RES-CHIP
METAL CHIP
METAL CHIP
RES-CHIP
RES-CHIP
100
10K
470
100
100
5%
5%
5%
5%
5%
1/8W
1/10W
1/10W
1/10W
1/10W
R2007
R2008
R2009
1-216-025-11 RES-CHIP
1-216-073-00 METAL CHIP
1-216-073-00 METAL CHIP
100
10K
10K
5%
5%
5%
1/10W
1/10W
1/10W
< CONNECTOR >
CN601
< LED >
D661
D663
D664
D665
D667
8-719-056-13
8-719-812-44
8-719-032-86
8-719-056-13
8-719-032-86
D668
8-719-812-44 LED TLO124 (I/1)
LED
LED
LED
LED
LED
SML79423C-TP15 (MD PLAY/PAUSE)
TLO124 (z REC)
SEL5420E (MD)
SML79423C-TP15 (CD PLAY/PAUSE)
SEL5420E (CD)
< FLUORESCENT INDICATOR TUBE >
FL601
1-517-985-11 INDICATOR TUBE, FLUORESCENT
< IC >
< VIBRATOR >
X201
1-767-286-11 VIBRATOR, CRYSTAL (22MHz)
X302
1-781-155-21 VIBRATOR, CERAMIC (10MHz)
**************************************************************
1-779-757-11 SOCKET, CONNECTOR (L TYPE) 29P
IC601
IC602
8-759-297-23 IC M66004M8FP
8-759-459-85 IC NJL63H400A
< JACK >
A-4475-916-A PANEL BOARD, COMPLETE
**********************
J601
1-764-106-21 JACK (PHONES)
4-212-590-22 HOLDER (FL)
93
PANEL
Ref. No.
POWER
Part No.
Description
Remark
< TRANSISTOR >
Q601
Q661
Q662
Q663
Q664
8-729-620-05
8-729-900-63
8-729-900-63
8-729-900-80
8-729-900-80
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
Q665
Q666
Q667
8-729-900-63 TRANSISTOR
8-729-900-63 TRANSISTOR
8-729-900-80 TRANSISTOR
2SC2603-EF
DTA124ES
DTA124ES
DTC114ES
DTC114ES
Ref. No.
< RESISTOR >
Description
Remark
1-762-875-21 SWITCH, KEYBOARD (FUNCTION)
1-762-875-21 SWITCH, KEYBOARD
(TUNING +, MD/CD M L)
S611
S612
1-762-875-21 SWITCH, KEYBOARD (TUNER/BAND)
1-762-875-21 SWITCH, KEYBOARD
(TUNING –, MD/CD l m)
1-762-875-21 SWITCH, KEYBOARD (z REC)
1-762-875-21 SWITCH, KEYBOARD (CD-MD SYNC)
1-762-875-21 SWITCH, KEYBOARD
(STEREO/MONO, REPEAT)
S613
S614
S615
DTA124ES
DTA124ES
DTC114ES
Part No.
S609
S610
S616
R601
R603
R607
R608
R609
1-249-441-11
1-249-417-11
1-249-441-11
1-249-434-11
1-249-417-11
CARBON
CARBON
CARBON
CARBON
CARBON
100K
1K
100K
27K
1K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R610
R611
R612
R615
R616
1-249-417-11
1-249-417-11
1-249-417-11
1-247-807-31
1-247-807-31
CARBON
CARBON
CARBON
CARBON
CARBON
1K
1K
1K
100
100
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R617
R618
R619
R620
R621
1-247-807-31
1-247-807-31
1-247-807-31
1-247-807-31
1-247-807-31
CARBON
CARBON
CARBON
CARBON
CARBON
100
100
100
100
100
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R639
R641
R642
R643
R644
1-249-393-11
1-249-415-11
1-249-417-11
1-249-419-11
1-247-843-11
CARBON
CARBON
CARBON
CARBON
CARBON
10
680
1K
1.5K
3.3K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R645
R646
R647
R648
R649
1-249-425-11
1-249-415-11
1-249-417-11
1-249-419-11
1-247-843-11
CARBON
CARBON
CARBON
CARBON
CARBON
4.7K
680
1K
1.5K
3.3K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R650
R651
R652
R661
R662
1-249-425-11
1-249-429-11
1-249-435-11
1-249-409-11
1-249-407-11
CARBON
CARBON
CARBON
CARBON
CARBON
4.7K
10K
33K
220
150
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R663
R664
R665
R666
R667
1-249-415-11
1-249-410-11
1-249-409-11
1-249-407-11
1-249-410-11
CARBON
CARBON
CARBON
CARBON
CARBON
680
270
220
150
270
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R668
1-249-413-11 CARBON
470
5%
1/4W
1-762-875-21 SWITCH, KEYBOARD
(TUNING MODE, PLAY MODE)
**************************************************************
A-4475-920-A POWER BOARD, COMPLETE (HK, TW)
A-4475-924-A POWER BOARD, COMPLETE (KR)
***********************
11-533-293-11 FUSE HOLDER (HK, TW)
< CAPACITOR >
C971
C972
C973
C974
C975
1-136-165-00
1-126-936-11
1-136-165-00
1-128-576-11
1-126-964-11
FILM
ELECT
FILM
ELECT
ELECT
0.1uF
3300uF
0.1uF
100uF
10uF
5%
20%
5%
20%
20%
50V
16V
50V
63V
50V
C976
C981
C982
C983
C984
1-126-964-11
1-136-165-00
1-135-933-11
1-136-165-00
1-126-943-11
ELECT
FILM
ELECT
FILM
ELECT
10uF
0.1uF
22000uF
0.1uF
2200uF
20%
5%
20%
5%
20%
50V
50V
16V
50V
25V
0.01uF
2.2uF
20%
20%
250V
50V
0 C991
C992
1-113-925-11 CERAMIC
1-126-961-11 ELECT
< CONNECTOR >
CN991
* CN992
* CN993
* CN994
1-564-321-00
1-564-687-11
1-564-519-11
1-770-730-11
PIN, CONNECTOR 2P
PIN, CONNECTOR 3P
PLUG, CONNECTOR 4P
CONNECTOR, BOARD TO BOARD 11P
< DIODE >
D971
D972
D973
D974
D975
8-719-024-99
8-719-024-99
8-719-024-99
8-719-024-99
8-719-024-99
DIODE
DIODE
DIODE
DIODE
DIODE
11ES2-NTA2B
11ES2-NTA2B
11ES2-NTA2B
11ES2-NTA2B
11ES2-NTA2B
< SWITCH >
D976
D977
D978
D979
D980
8-719-024-99
8-719-024-99
8-719-024-99
8-719-983-86
8-719-947-12
DIODE
DIODE
DIODE
DIODE
DIODE
11ES2-NTA2B
11ES2-NTA2B
11ES2-NTA2B
MTZJ-T-72-33A
MTZJ-T-72-4.7A
DIODE
DIODE
DIODE
DIODE
DIODE
D3SBA20-4101
11ES2-NTA2B
11ES2-NTA2B
11ES2-NTA2B
11ES2-NTA2B
S601
S602
S603
S604
S605
1-418-632-11
1-762-875-21
1-762-875-21
1-762-875-21
1-762-875-21
ENCODER, ROTARY (VOLUME)
SWITCH, KEYBOARD (I/1)
SWITCH, KEYBOARD (s (CD))
SWITCH, KEYBOARD (HS (CD))
SWITCH, KEYBOARD (A (CD))
D981
D982
D983
D984
D985
8-719-028-23
8-719-024-99
8-719-024-99
8-719-024-99
8-719-024-99
S606
S607
S608
1-762-875-21 SWITCH, KEYBOARD (s (MD))
1-762-875-21 SWITCH, KEYBOARD (HS (MD))
1-762-875-21 SWITCH, KEYBOARD (A (MD))
D986
D987
D991
8-719-911-19 DIODE 1SS119-25
8-719-911-19 DIODE 1SS119-25
8-719-911-19 DIODE 1SS119-25
94
The components identified by mark 0 or dotted
line with mark 0 are critical for safety.
Replace only with part number specified.
POWER
Ref. No.
D992
D993
Part No.
Description
Remark
Ref. No.
Description
SW
Remark
< DIODE >
D881
D882
< FUSE >
0 F991
Part No.
8-719-911-19 DIODE 1SS119-25
8-719-911-19 DIODE 1SS119-25
SP
8-719-911-19 DIODE 1SS119-25
8-719-911-19 DIODE 1SS119-25
1-532-388-31 FUSE (T2AL/250V) (HK, TW)
< COIL >
< TRANSISTOR >
Q971
Q972
Q973
Q974
Q975
8-729-018-59
8-729-922-37
8-729-922-37
8-729-900-63
8-729-620-05
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
Q991
8-729-620-05 TRANSISTOR
1-420-872-00 COIL, AIR-CORE
1-420-872-00 COIL, AIR-CORE
< TRANSISTOR >
Q881
8-729-111-29 TRANSISTOR
2SD1616A-K
< RESISTOR >
2SC2603-EF
< RESISTOR >
0 R971
R972
R973
R974
R975
1-219-153-11
1-249-421-11
1-249-425-11
1-249-413-11
1-249-413-11
FUSIBLE
CARBON
CARBON
CARBON
CARBON
10
2.2K
4.7K
470
470
5%
5%
5%
5%
5%
1/4W F
1/4W
1/4W
1/4W
1/4W
R976
R977
R978
R979
R980
1-249-429-11
1-249-429-11
1-249-441-11
1-249-417-11
1-249-417-11
CARBON
CARBON
CARBON
CARBON
CARBON
10K
10K
100K
1K
1K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
0 R981
0 R982
R991
R992
R993
1-219-121-11
1-219-124-11
1-249-429-11
1-249-429-11
1-249-417-11
FUSIBLE
FUSIBLE
CARBON
CARBON
CARBON
0.22
0.68
10K
10K
1K
5%
5%
5%
5%
5%
1/4W F
1/4W F
1/4W
1/4W
1/4W
1-249-417-11 CARBON
1-247-843-11 CARBON
1K
3.3K
5%
5%
1/4W
1/4W
R994
R995
L881
L882
2SB1375 (LB-SONY)
2SD2144S-UVW
2SD2144S-UVW
DTA124ES
2SC2603-EF
0 R881
0 R882
0 R883
0 R884
R885
1-215-864-00
1-215-864-00
1-215-864-00
1-215-864-00
1-247-903-00
METAL OXIDE
METAL OXIDE
METAL OXIDE
METAL OXIDE
CARBON
150
150
150
150
1M
5%
5%
5%
5%
5%
1W
1W
1W
1W
1/4W
R886
R887
R888
R889
R890
1-249-431-11
1-249-431-11
1-249-421-11
1-247-843-11
1-249-429-11
CARBON
CARBON
CARBON
CARBON
CARBON
15K
15K
2.2K
3.3K
10K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
0 R891
R892
R893
R894
R895
1-216-454-11
1-260-076-11
1-260-076-11
1-260-076-11
1-260-076-11
METAL OXIDE
CARBON
CARBON
CARBON
CARBON
390
10
10
10
10
5%
5%
5%
5%
5%
2W
F
1/2W
1/2W
1/2W
1/2W
0 R896
1-216-454-11 METAL OXIDE
390
5%
2W
F
F
F
F
F
< RELAY >
RY881
1-755-170-11 RELAY (12V)
< RELAY >
< TERMINAL >
0 RY991
1-755-276-11 RELAY, POWER
TM881
1-537-238-31 TERMINAL BOARD
(SPEAKER IMPEDANCE 6-16Ω)
**************************************************************
< SWITCH >
0 S991
1-571-309-11 SWITCH (VOLTAGE SELECTOR) (HK, TW)
1-671-115-21 SW BOARD
**********
*
< TRANSFORMER >
0 T900
1-433-970-11 TRANSFORMER, POWER
0 T992
1-424-485-11 FILTER, LINE
**************************************************************
< CONNECTOR >
* CN601
1-674-628-12 SP BOARD
*********
< SWITCH >
S601
S602
S604
< CAPACITOR >
C881
C882
C883
C884
C885
1-126-959-11
1-136-495-11
1-136-495-11
1-136-495-11
1-136-495-11
ELECT
FILM
FILM
FILM
FILM
1-506-486-11 PIN, CONNECTOR 7P
0.47uF
0.068uF
0.068uF
0.068uF
0.068uF
20%
5%
5%
5%
5%
50V
50V
50V
50V
50V
1-572-126-21 SWITCH, PUSH (1 KEY) (REC POSITION)
1-572-126-21 SWITCH, PUSH (1 KEY) (PACK OUT)
1-771-264-11 SWITCH, PUSH (DETECTION) (1 KEY)
(PB POSITION)
**************************************************************
< CONNECTOR >
* CN881
* CN882
1-770-747-11 CONNECTOR, BOARD TO BOARD 12P
1-770-747-11 CONNECTOR, BOARD TO BOARD 12P
The components identified by mark 0 or dotted
line with mark 0 are critical for safety.
Replace only with part number specified.
95
HCD-F3MD
Ref. No.
Part No.
Description
Remark
Ref. No.
Part No.
Description
Remark
MISCELLANEOUS
**************
13
14
16
17
57
1-777-240-11
1-791-211-11
1-773-212-11
1-792-756-11
1-693-473-31
WIRE (FLAT TYPE) (21 CORE)
WIRE (FLAT TYPE) (23 CORE)
WIRE (FLAT TYPE) (25 CORE)
WIRE (FLAT TYPE) (29 CORE)
TUNER (FM/AM TUNER UNIT) (TW)
57
59
60
61
0 62
1-693-473-41
1-773-115-11
1-773-006-11
1-569-972-21
1-769-079-21
TUNER (FM/AM TUNER UNIT) (HK, KR)
WIRE (FLAT TYPE) (19 CORE)
WIRE (FLAT TYPE) (15 CORE)
SOCKET, SHORT 2P
CORD, POWER (KR)
0 62
* 158
0 160
0 255
256
1-769-744-11
1-667-954-11
A-4672-541-A
8-820-113-01
1-782-817-11
CORD, POWER (HK, TW)
PC BOARD, FLEXIBLE
OPTICAL PICK-UP KMS-260B/S1NP
OPTICAL PICK-UP KSS-213BH/Z-NP
WIRE (FLAT TYPE) (16 CORE)
1-500-502-11
X-4952-989-1
X-4917-504-1
A-4672-771-A
A-4672-475-A
HEAD, OVER WRITE
BASE (BU-5S) ASSY (CD)
MOTOR ASSY (SLED) (CD)
MOTOR (LD) ASSY (LOADING) (CD)
MOTOR ASSY, SPINDLE (MD)
HR901
M101
M102
M103
M901
M902
M903
S102
A-4672-474-A MOTOR ASSY, SLED (MD)
X-4949-264-1 MOTOR ASSY, LOADING (MD)
1-762-148-21 SWITCH, PUSH (2 KEY)
(PROTECT/REFLECT RATE DETECT)
0 T901
1-433-966-11 TRANSFORMER, POWER
************************************************************
**************
HARDWARE LIST
**************
#1
#2
#3
#4
#5
7-685-871-01
7-685-647-79
7-685-650-91
7-685-533-19
7-627-852-08
SCREW +BVTT 3X6 (S)
SCREW +BVTP 3X10 TYPE2 TT (B)
SCREW +BVTP 3X16 TYPE2 TT (B)
SCREW +BTP 2.6X6 TYPE2 N-S
SCREW, PRECISION +P 1.7X2.5
#6
7-621-772-40 SCREW +B 2X8
#7
7-621-772-20 SCREW +B 2X5
#8
7-685-133-19 SCREW (DIA. 2.6) (IT3B)
#12
7-621-772-10 SCREW +B 2X4
************************************************************
ACCESSORIES & PACKING MATERIALS
*******************************
0
0
1-569-008-21 ADAPTOR, CONVERSION 2P (TW)
1-770-019-11 ADAPTOR, CONVERSION PLUG 3P (HK)
The components identified by mark 0 or dotted
line with mark 0 are critical for safety.
Replace only with part number specified.
9-929-273-11
Sony Corporation
Audio Entertainment Group
96
2000K05016-1D
Printed in Japan C 2000. 11
Published by General Engineering Dept.