Moog RHW75C12N Instruction manual

© 2011, Moog Videolarm, Inc. All Rights Reserved
RHW75C12N
Vandal-Resistant Rugged (Outdoor Dome Housing)
www.videolarm.com
Installation and Operation Instructions for the following model:
RHW75C12N
IP Network Ready 7” Vandal-Resistant Outdoor dome housing with wall mount, clear dome polycarbonate, 12VDC input (ideal for solar and battery powered
applications), heater/blower, 42vA, for an IP Network PTZ camera.
Before attempting to connect or operate this product, please read these instructions completely.
To be used with the 81-IN5481 Instruction Manual.
W81-IN5318
01-19-2012
IMPORTANT SAFEGUARDS
1
Read these instructions.
2
Keep these instructions.
3
Heed all warnings
4
Follow all instructions.
5
Do not use this apparatus near water.
6
Clean only with damp cloth.
7
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
Do not block any of the ventilation openings. Install in accordance with the
manufacturers instructions.
8
9
SAFETY PRECAUTIONS
Cable Runs- All cable runs must be within permissible distance.
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER ( OR BACK). NO USER- SERVICEABLE PARTS INSIDE. REFER SEVICING
TO QUALIFIED SERVICE PERSONNEL.
Mounting - This unit must be properly and securely mounted to a supporting
structure capable of sustaining the weight of the unit.
Accordingly:
a. The installation should be made by a qualified installer.
b. The installation should be in compliance with local codes.
c. Care should be exercised to select suitable hardware to install the unit, taking into
account both the composition of the mounting surface and the weight of the unit.
10 Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus ( including amplifiers) that produce heat.
11 Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding type
plug has two blades and a third grounding prong. The wide blade or the third
prong are provided for your safety. When the provided plug does not fit into your
outlet, consult an electrician for replacement of the obsolete outlet.
12 Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
13 Only use attachment/ accessories specified by the manufacturer.
14 Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer,
or sold with the apparatus. When a cart is used, use caution when moving the cart/
apparatus combination to avoid injury from tip-over.
15 Unplug this apparatus during lighting storms or when unused for long periods of time.
16 Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled of objects have fallen into the apparatus, the
The lightning flash with an arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of non-insulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude
to constitute a risk to persons.
Este símbolo se piensa para alertar al usuario a la presencia
del “voltaje peligroso no-aisIado” dentro del recinto de los
productos que puede ser un riesgo de choque eléctrico.
Ce symbole est prévu pour alerter I’utilisateur à la presence
“de la tension dangereuse” non-isolée dans la clôture de
produits qui peut être un risque de choc électrique.
Dieses Symbol soll den Benutzer zum Vorhandensein der
nicht-lsolier “Gefährdungsspannung” innerhalb der
Produkteinschließung alarmieren die eine Gefahr des
elektrischen Schlages sein kann.
Este símbolo é pretendido alertar o usuário à presença “di
tensão perigosa non-isolada” dentro do cerco dos produtos
que pode ser um risco de choque elétrico.
Questo simbolo è inteso per avvertire I’utente alla presenza
“di tensione pericolosa” non-isolata all’interno della
recinzione dei prodotti che può essere un rischio di scossa
elettrica.
apparatus has been exposed to rain or moisture, does not operate normally, or
has been dropped.
Be sure to periodically examine the unit and the supporting structure to make sure that the integrity
of the installation is intact. Failure to comply with the foregoing could result in the unit separating
from the support structure and falling, with resultant damages or injury to anyone or anything struck
by the falling unit.
UNPACKING
Unpack carefully. Electronic components can be
damaged if improperly handled or dropped. If an item
appears to have been damaged in shipment, replace
it properly in its carton and notify the shipper.
Be sure to save:
1 The shipping carton and packaging material.
They are the safest material in which to make future
shipments of the equipment.
2 These Installation and Operating Instructions.
SERVICE
If technical support or service is needed, contact us at
the following number:
TECHNICAL SUPPORT
AVAILABLE 24 HOURS
1 - 800 - 554 -1124
The exclamation point within an equilateral
triangle is intended to alert the user to
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
Este símbolo del punto del exclamation se piensa para
alertar al usuario a la presencia de instrucciones importantes
en la literatura que acompaña la aplicación.
Ce symbole de point d’exclamation est prévu pour alerter
l’utilisateur à la presence des instructions importantes dans
la littérature accompagnant l’appareil.
Dieses Ausruf Punktsymbol soll den Benutzer zum
Vorhandensein de wichtigen Anweisungen in der Literatur
alarmieren, die das Gerät begleitet.
Este símbolo do ponto do exclamation é pretendido alertar o
usuário à presença de instruções importantes na literatura
que acompanha o dispositivo.
Questo simbolo del punto del exclamaton è inteso per
avvertire l’utente alla presenza delle istruzioni importanti nella
letteratura che accompagna l'apparecchio.
Limited Warranty for Moog Videolarm Products
Moog Videolarm warrants these products to be free from defects in material or workmanship as follows:
PRODUCT CATEGORY
PARTS \ LABOR
AllEnclosuresandElectronics*
Five(5)Years
Poles/PolEvators™/CamEvator
Three(3)Years
WarriorSeries™/Q-View™/IRIlluminators
Five(5)Years
SViewSeries™
Five(5)Years**6monthsifusedinautoscan/touroperation
Controllers
Five(5)Years
PowerSupplies
Five(5)Years
EcoKit
Three(3)Years
AccessoryBrackets
Five(5)Years
LibertyDome
Three(3)Years
*DeputyDome™,NiteTrac™,IglooDome,PurgeDome™
Three(3)Years**6monthsifusedinautoscan/touroperation
During the labor warranty period, to repair the Product, Purchaser will either return the defective product, freight prepaid, or deliver it to Moog Videolarm
Inc. Decatur GA. The Product to be repaired is to be returned in either its original carton or a similar package affording an equal degree of protection with
a RMA # (Return Materials Authorization number) displayed on the outer box or packing slip. To obtain a RMA# you must contact our Technical Support
Team at 800.554.1124, extension 101. Moog Videolarm will return the repaired Product freight prepaid to Purchaser. Moog Videolarm is not obligated to
provide Purchaser with a substitute unit during the warranty period or at any time. After the applicable warranty period, Purchaser must pay all labor and/or
parts charges.
The limited warranty stated in these product instructions is subject to all of the following terms and conditions.
TERMS AND CONDITIONS
1. NOTIFICATION OF CLAIMS: WARRANTY SERVICE: If Purchaser believes that the Product is defective in material or workmanship, then written notice with an
explanation of the claim shall be given promptly by Purchaser to Moog Videolarm. All claims for warranty service must be made within the warranty period.
If after investigation Moog Videolarm determines the reported problem was not covered by the warranty, Purchaser shall pay Moog Videolarm for the cost of
investigating the problem at its then prevailing per incident billable rate. No repair or replacement of any Product or part thereof shall extend the warranty period
of the entire Product. The specific warranty on the repaired part only shall be in effect for a period of ninety (90) days following the repair or replacement of that
part or the remaining period of the Product parts warranty, whichever is greater.
2. EXCLUSIVE REMEDY: ACCEPTANCE: Purchaser’s exclusive remedy and Moog Videolarm’s sole obligation is to supply (or pay for) all labor necessary to repair any
Product found to be defective within the warranty period and to supply, at no extra charge, new or rebuilt replacements for defective parts.
3. EXCEPTIONS TO LIMITED WARRANTY:Moog Videolarm shall have no liability or obligation to Purchaser with respect to any Product requiring service during the
warranty period which is subjected to any of the following: abuse, improper use, negligence, accident, lightning damage or other acts of God (i.e., hurricanes,
earthquakes), modification, failure of the end-user to follow the directions outlined in the product instructions, failure of the end-user to follow the maintenance
procedures recommended by the International Security Industry Organization, written in product instructions, or recommended in the service manual for the
Product. Furthermore, Moog Videolarm shall have no liability where a schedule is specified for regular replacement or maintenance or cleaning of certain parts
(based on usage) and the end-user has failed to follow such schedule; attempted repair by non-qualified personnel; operation of the Product outside of the
published environmental and electrical parameters, or if such Product’s original identification (trademark, serial number) markings have been defaced, altered,
or removed. Moog Videolarm excludes from warranty coverage Products sold AS IS and/or WITH ALL FAULTS and excludes used Products which have not
been sold by Moog Videolarm to the Purchaser. All software and accompanying documentation furnished with, or as part of the Product is furnished “AS IS”
(i.e., without any warranty of any kind), except where expressly provided otherwise in any documentation or license agreement furnished with the Product. Any
cost associated with removal of defective product and installation of replacement product is not included in this warranty.
4. PROOF OF PURCHASE:The Purchaser’s dated bill of sale must be retained as evidence of the date of purchase and to establish warranty eligibility.
DISCLAIMER OF WARRANTY
EXCEPT FOR THE FOREGOING WARRANTIES, Moog Videolarm HEREBY DISCLAIMS AND EXCLUDES ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO ANY AND/OR ALL IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND/OR
ANY WARRANTY WITH REGARD TO ANY CLAIM OF INFRINGEMENT THAT MAY BE PROVIDED IN SECTION 2-312(3) OF THE UNIFORM COMMERCIAL
CODE AND/OR IN ANY OTHER COMPARABLE STATE STATUTE. Moog Videolarm HEREBY DISCLAIMS ANY REPRESENTATIONS OR WARRANTY THAT
THE PRODUCT IS COMPATIBLE WITH ANY COMBINATION OF NON-Moog Videolarm PRODUCTS OR NON-Moog Videolarm RECOMMENDED PRODUCTS
PURCHASER MAY CHOOSE TO CONNECT TO THE PRODUCT.
LIMITATION OF LIABILITY
THE LIABILITY OF Moog Videolarm, IF ANY, AND PURCHASER’S SOLE AND EXCLUSIVE REMEDY FOR DAMAGES FOR ANY CLAIM OF ANY KIND
WHATSOEVER, REGARDLESS OF THE LEGAL THEORY AND WHETHER ARISING IN TORT OR CONTRACT, SHALL NOT BE GREATER THAN THE ACTUAL
PURCHASE PRICE OF THE PRODUCT WITH RESPECT TO WHICH SUCH CLAIM IS MADE. IN NO EVENT SHALL Moog Videolarm BE LIABLE TO PURCHASER
FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES OF ANY KIND INCLUDING, BUT NOT LIMITED TO, COMPENSATION,
REIMBURSEMENT OR DAMAGES ON ACCOUNT OF THE LOSS OF PRESENT OR PROSPECTIVE PROFITS OR FOR ANY OTHER REASON WHATSOEVER.
!
English
Español
Français
Deutsch
Portuguese
Italiano
Electrical Specifications
Power 12VDC
Contents of Box
RHW75
12 VDC
49 Watts
Accessories:
Heater: 20 Watts, Blower: 2 Watt
Camera Power: (See Camera Specifications): 27 Watts Max
Tools Required:
.100” Flat Head Screwdriver
Phillips Head Screwdriver
12 VDC
49 Vatios
De Accesorios: Calentador: 20 Watts, Blower: 2 Vatio
Energía De la Cámara fotográfica De : (Véase Las
Especificaciones De la Cámara fotográfica): 27 Vatios
De Herramientas Máximas
Requeridas: Destornillador Principal Phillips Del Destornillador
Principal Plano Del 100"
12 VDC
49 Watts
D'Accessoires : Réchauffeur : 20 Watts, Ventilateur : 2 watts.
Puissance D'Appareil-photo : (Voir Les Caractéristiques
D'Appareil-photo) : 27 Watts De Maximum
Les Outils Ont exigé : Tournevis Principal Phillips De Tournevis
Principal Plat De 100".
12 VDC
49 Watt
Zusatzgerät-:
Heizung: 20 Watts, Blower: 2
Watt-Kamera-Energie: (Sehen Sie Kamera-Spezifikationen):
27 Watt Maximale Werkzeug-Erfordert: 100"Flacher
Hauptschraubenzieher-Kreuzkopfhauptschraubenzieher
12 VDC
49 Watts
De Acessórios:
Calefator: 20 Watts, Blower: 2 Watt
Poder Da Câmera De :(Veja Especificações Da Câmera):
27 Watts De Ferramentas Máximas Requereram: Chave de
fenda Principal Phillips Da Chave de fenda Principal Lisa Do 100"
Pendent Model
(ONLY)
12 VDC
49 Watt
Di Accessori: Riscaldatore: 20 Watts, Blower: 2 Watt
Alimentazione Della Macchina fotografica Da :
(Veda Le Specifiche Della Macchina fotografica): 27 Watt
Di Attrezzi Massimi Hanno richiesto: Cacciavite Capo "phillips"
Del Cacciavite Capo Piano Del 100"
*
* NOT included with E or 12V models
1
WALL MOUNTING
2
4”-5”
Bracket is designed for 45° conduit fitting (If using the
conduit). Run wire into bracket secure to wall.
• El soporte se diseña para la guarnición del conducto 45° (si usa el
conducto). Funcione con el alambre en el soporte seguro para
emparedar.
• La parenthèse est conçue pour l'ajustage de précision du conduit 45° (si
à l'aide du conduit). Courez le fil dans la parenthèse bloquée pour murer.
• Haltewinkel ist für Befestigung des Rohres 45° bestimmt (wenn das Rohr
verwendet wird). Lassen Sie Draht in den Haltewinkel laufen, der, um zu
ummauern sicher ist.
• O suporte é projetado para o encaixe da canalização 45° (se usando a
canalização). Funcione o fio no suporte seguro para murar.
• La staffa è progettata per il montaggio del condotto 45° (se per mezzo
del condotto). Faccia funzionare il legare nella staffa sicura per murare.
3
Secure lanyard to lanyard clip
Trim incoming control & power wires to 4”- 5”,
for either wall or pendent bracket
• Con seguridad soporte del montaje a emparedar. Tire del cableado
a través del soporte y del ojal de la posición según lo demostrado.
• Solidement parenthèse de bâti à murer. Tirez le câblage par la
parenthèse et le canon isolant de position comme montré.
• Sicher Einfassung Haltewinkel wall. Ziehen Sie Verdrahtung durch
Haltewinkel und Position Gummimuffe, wie gezeigt.
• Firmemente suporte da montagem a wall. Puxe a fiação através do
suporte e do ilhó da posição como mostrado.
• Saldamente staffa del supporto da wall. Tiri i collegamenti tramite la
staffa ed il gommino di protezione di posizione come indicato.
4
Complete ALL wiring connections
• Con seguridad soporte del montaje a emparedar. Tire del cableado
a través del soporte y del ojal de la posición según lo demostrado.
• Con seguridad soporte del montaje a emparedar. Tire del cableado
a través del soporte y del ojal de la posición según lo demostrado.
• Solidement parenthèse de bâti à murer. Tirez le câblage par la
parenthèse et le canon isolant de position comme montré.
• Solidement parenthèse de bâti à murer. Tirez le câblage par la
parenthèse et le canon isolant de position comme montré.
• Sicher Einfassung Haltewinkel wall. Ziehen Sie Verdrahtung durch
Haltewinkel und Position Gummimuffe, wie gezeigt.
• Sicher Einfassung Haltewinkel wall. Ziehen Sie Verdrahtung durch
Haltewinkel und Position Gummimuffe, wie gezeigt.
• Firmemente suporte da montagem a wall. Puxe a fiação através do
suporte e do ilhó da posição como mostrado.
• Firmemente suporte da montagem a wall. Puxe a fiação através do
suporte e do ilhó da posição como mostrado.
• Saldamente staffa del supporto da wall. Tiri i collegamenti tramite la
staffa ed il gommino di protezione di posizione come indicato.
• Saldamente staffa del supporto da wall. Tiri i collegamenti tramite la
staffa ed il gommino di protezione di posizione come indicato.
5
WALL MOUNTING
6
!
26 Watts
C
Important
Gasket
Must be in
place
COAX
(coax wire not supplied)
Wiring the dome can be completed by
referring to the diagram.
• Atar con alambre la bóveda puede ser terminada
refiriendo al diagrama.
• Le câblage du dôme peut être accompli en se
rapportant au diagramme.
• Das Verdrahten der Haube kann durchgeführt
werden, indem man auf das Diagramm sich bezieht.
• Wiring a abóbada pode ser terminado consultando
ao diagrama.
• Legare la cupola può essere completato riferendosi
allo schema.
7
To lock turn clockwise
Align large arrows
• Con seguridad soporte del montaje a emparedar. Tire del cableado
a través del soporte y del ojal de la posición según lo demostrado.
• Solidement parenthèse de bâti à murer. Tirez le câblage par la
parenthèse et le canon isolant de position comme montré.
• Sicher Einfassung Haltewinkel wall. Ziehen Sie Verdrahtung durch
Haltewinkel und Position Gummimuffe, wie gezeigt.
• Firmemente suporte da montagem a wall. Puxe a fiação através do
suporte e do ilhó da posição como mostrado.
• Saldamente staffa del supporto da wall. Tiri i collegamenti tramite la
staffa ed il gommino di protezione di posizione come indicato.
8
Secure with ¼” Allen wrench
• Con seguridad soporte del montaje a emparedar. Tire del cableado
a través del soporte y del ojal de la posición según lo demostrado.
• Con seguridad soporte del montaje a emparedar. Tire del cableado
a través del soporte y del ojal de la posición según lo demostrado.
• Solidement parenthèse de bâti à murer. Tirez le câblage par la
parenthèse et le canon isolant de position comme montré.
• Solidement parenthèse de bâti à murer. Tirez le câblage par la
parenthèse et le canon isolant de position comme montré.
• Sicher Einfassung Haltewinkel wall. Ziehen Sie Verdrahtung durch
Haltewinkel und Position Gummimuffe, wie gezeigt.
• Sicher Einfassung Haltewinkel wall. Ziehen Sie Verdrahtung durch
Haltewinkel und Position Gummimuffe, wie gezeigt.
• Firmemente suporte da montagem a wall. Puxe a fiação através do
suporte e do ilhó da posição como mostrado.
• Firmemente suporte da montagem a wall. Puxe a fiação através do
suporte e do ilhó da posição como mostrado.
• Saldamente staffa del supporto da wall. Tiri i collegamenti tramite la
staffa ed il gommino di protezione di posizione come indicato.
• Saldamente staffa del supporto da wall. Tiri i collegamenti tramite la
staffa ed il gommino di protezione di posizione come indicato.
9
FOR PENDENT/
WALL MOUNTING
10
4”-5”
Trim incoming control and power wires to 4-5 for
either wall or pendent bracket
• La tapa segura de la cubierta SM5 con mercancías duras
proporcionó; termine a la asamblea por las instrucciones SM5
• Le dessus bloqué du logement SM5 avec les articles durs a
fourni; accomplissez l'assemblée par instructions SM5
• Sichere Oberseite des Gehäuses SM5 mit den harten Waren
bereitgestellt; schließen Sie Versammlung pro Anweisungen
SM5 ab
• Parte superior segura da carcaça SM5 com os mercadorias
duros fornecidos; termine o conjunto por as instruções SM5
• Parte superiore sicura dell'alloggiamento SM5 con gli articoli
duri forniti; completi l'assemblea per istruzioni SM5
11
Secure lanyard to lanyard clip
• Con seguridad soporte del montaje a emparedar. Tire del cableado
a través del soporte y del ojal de la posición según lo demostrado.
• Solidement parenthèse de bâti à murer. Tirez le câblage par la
parenthèse et le canon isolant de position comme montré.
• Sicher Einfassung Haltewinkel wall. Ziehen Sie Verdrahtung durch
Haltewinkel und Position Gummimuffe, wie gezeigt.
• Firmemente suporte da montagem a wall. Puxe a fiação através do
suporte e do ilhó da posição como mostrado.
• Saldamente staffa del supporto da wall. Tiri i collegamenti tramite la
staffa ed il gommino di protezione di posizione come indicato.
12
26 Watts
C
COAX
(coax wire not supplied)
Complete all wiring connections
(coax wire not supplied)
• Termine todas las conexiones del cableado
(alambre coaxil no suministrado)
• Accomplissez tous les raccordements de câblage
(fil coaxial non fourni)
• Schließen Sie alle Verdrahtungsanschlüsse ab
(koaxialer Draht nicht geliefert)
• Termine todas as conexões da fiação
(fio co-axial não fornecido)
• Completi tutti i collegamenti dei collegamenti
(legare coassiale non fornito)
Wiring the dome can be completed by
referring to the diagram.
• Atar con alambre la bóveda puede ser terminada
refiriendo al diagrama.
• Le câblage du dôme peut être accompli en se
rapportant au diagramme.
• Das Verdrahten der Haube kann durchgeführt
werden, indem man auf das Diagramm sich bezieht.
• Wiring a abóbada pode ser terminado consultando
ao diagrama.
• Legare la cupola può essere completato riferendosi
allo schema.
13
14
Important
Gasket
Must be in
place
!
Align large arrows
To lock turn clockwise
• Alinee las flechas grandes
• Alinee las flechas grandes
• Alignez les grandes flèches
• Alignez les grandes flèches
• Richten Sie große Pfeile aus
• Richten Sie große Pfeile aus
• Alinhe grandes setas
• Alinhe grandes setas
• Allini le grandi frecce
• Allini le grandi frecce
15
Secure with ¼” Allen wrench
• Asegure con la llave Allen del ¼”
• Fixez clé Allen avec de ¼”
• Sichern Sie mit ¼“ Inbusschlüssel
• Fixe com chave Allen do ¼ de”
• Fissi con chiave di Allen del ¼”
16
!
To loosen - unscrew bolts ½” turn counter
clockwise
• Para aflojar - desatornille a la derecha contrario de la vuelta
del ½ de los pernos”
• Pour se desserrer - dans le sens des aiguilles d'une montre de
tour dévissez de boulons ½ » contre• Um sich zu lösen - schrauben Sie Schraubbolzen ½“
Umdrehungs-Gegenrechtses herum ab
• Para afrouxar - desaparafuse sentido horário contrário volta
do ½ dos parafusos da”
• Per allentare - sviti in senso orario di girata del ½ dei bulloni„
contro
17
POWER
Power and Control Inputs (Outside of Housing)
RJ45Camera Power (+ 12 VDC)
24VAC
Camera
Power (- 12 VDC)
1
2
1
3 2
3
4
4
Red
POWER
Orange
Camera
Red
Accessory
VDC)
Camera Power (+12Orange
Heater/Blower
Yellow
Accessory Power (-12 VDC)
Heater/Blower
Green
Max 40 Watts
Yellow
52Green
Watts
CONTROL RJ45 Ethernet Connector
1/0
1
2
3
4
Alarm 1
Alarm 2
Alarm 3
Common
Blue
Violet
Gray
White
BNC
Make the appropriate male and female connections. Indoor model does not include pre-run cables.
• Haga las conexiones masculinas y femeninas apropiadas. El modelo de interior no incluye pre-funciona los cables.
• Établissez les rapports masculins et femelles appropriés. Le modèle d'intérieur n'inclut pas pré-courent des câbles.
• Stellen Sie die passenden männlichen und weiblichen Beziehungen her. Innenmodell schließt nicht vor-laufen lassen Kabel
ein.
• Faça as conexões masculinas e fêmeas apropriadas. O modelo indoor não inclui pre-funciona cabos.
• Faccia i collegamenti maschii e femminili adatti. Il modello dell'interno non include pre-fa funzionare i cavi.
Power and Control Inputs (Inside of Housing)
12
19
18
,5
22
,75
20
1,0
18
1,5
16
2,5
14
4
12
6
10
MM2
AWG
POWER
1
Camera Power (+12 VDC)
Red
2
Camera Power (-12 VDC)
Orange
Make the appropriate male and female connections.
Indoor model does not include pre-run cables.
• Haga las conexiones masculinas y femeninas apropiadas. El modelo
de interior no incluye pre-funciona los cables.
• Établissez les rapports masculins et femelles appropriés. Le modèle
d'intérieur n'inclut pas pré-courent des câbles.
• Stellen Sie die passenden männlichen und weiblichen Beziehungen
her. Innenmodell schließt nicht vor-laufen lassen Kabel ein.
• Faça as conexões masculinas e fêmeas apropriadas. O modelo indoor
não inclui pre-funciona cabos.
• Faccia i collegamenti maschii e femminili adatti. Il modello dell'interno
non include pre-fa funzionare i cavi.
These
are recommended
distances
The
beam
angle may bemaximum
adjusted on
the
for 12VDC
a 10% voltage drop.
bottom
of with
the unit.
• Éstos se recomiendan las distancias máximas para
12VDC con una gota del voltage del 10%.
• Ceux-ci sont recommandés des distances maximum
pour 12VDC avec une chute de tension de 10%.
• Diese werden maximale Abstände für 12VDC mit
einem 10% Spannungsabfall empfohlen.
• Estes são recomendados distâncias máximas para
12VDC com uma queda de tensão de 10%.
• Questi sono suggeriti distanze massime per 12VDC
con una differenza de potenziale di 10%.
PB24 Addendum
20
Additional wires are provided to run power to PB24. Use with connector supplied. Run RJ45 connector
through PB24, wall mount, and connect lead from housing.
• Los alambres adicionales se proporcionan a la energía funcionada con a PB24. El uso con el conectador proveyó.
Funcione con el conectador RJ45 con PB24, emparede el montaje, y conecte el plomo de la cubierta.
• Des fils additionnels sont fournis à la puissance courue à PB24. L'utilisation avec le connecteur a fourni. Courez le
connecteur RJ45 par PB24, murez le bâti, et reliez le fil du logement.
• Zusätzliche Drähte zur Verfügung gestellt zu laufen gelassener Energie zu PB24. Gebrauch mit Verbindungsstück lieferte.
Laufen lassen Sie Verbindungsstück RJ45 durch PB24, ummauern Sie Einfassung und anschließen Sie Blei vom Gehäuse n.
• Os fios adicionais são fornecidos ao poder funcionado a PB24. O uso com conector forneceu. Funcione o conector RJ45
com PB24, mure a montagem, e conecte a ligação da carcaça.
• I legare supplementari sono forniti a potere funzionato a PB24. L'uso con il connettore ha fornito. Faccia funzionare il
connettore RJ45 con PB24, muri il supporto e colleghi il cavo da alloggiamento.
21
22

Tab

Connect Lanyard to trim ring assembly.
• Conecte el acollador con el montaje del anillo del
ajuste.
• Reliez la lanière à l'anneau d'équilibre.
• Schließen Sie Abzuglinie an Ordnung Ring an.
• Conecte o colhedor ao conjunto do anel da
guarnição.
• Colleghi la cordicella al complessivo dell'anello
della cornice.
Align the arrows on the outside of the dome
and lock.
• Alinee las flechas en el exterior de la bóveda y
trábese.
• Alignez les flèches sur l'extérieur du dôme et
fermez à clef.
• Richten Sie die Pfeile auf der Außenseite der
Haube aus und verriegeln Sie sich.
• Alinhe as setas na parte externa da abóbada e
trave-as.
• Allinei le frecce sulla parte esterna della cupola e
blocchi.
23
24
Fasten down the dome with a Phillips screwdriver.
Wipe the dome clean. Please follow the proper
cleaning procedure.
• Sujete abajo de la bóveda con un destornillador Phillips.
• Limpie la cúpula limpio. Por favor, siga el procedimiento de
• Attachez en bas du dôme avec un tournevis Phillips.
• Befestigen Sie sich hinunter die Haube mit einem Kreuzkopfschraubenzieher.
• Prenda abaixo a abóbada com uma chave de fenda Phillips.
• Fissisi giù la cupola con un cacciavite "phillips".
limpieza adecuado, como se muestra.
• Essuyez le dôme propre. S'il vous plaît suivre la procédure de
nettoyage, comme indiqué.
• Wischen Sie die Kuppel reinigen. Bitte beachten Sie die
ordnungsgemäße Reinigung Verfahren.
• Limpe a cúpula limpo. Por favor, siga o procedimento
adequado de limpeza conforme.
• Pulire la cupola pulito. Si prega di seguire la corretta
procedura di pulizia, come.
Replacement Parts List
14
RHW75
IRHW75
15
16
13
12
11
10
9
8
7
5
4
6
3
1
2
1
1A
2
3
4
5
5A
6
7
8
8A
9
10
11
12
13
14
15
16
N/S
N/S
PART NUMBER
RC7C
RC7T
RPRH752
RPRH7503
RPNET02
RPFD072
RPFD072/12
RPFD080
RP40PCMD01
RP70FP7PB
RP70FP7PB12
RPFD041
RPFD2612
RPFD3245
RPGK3356
RP3458
RP3551
RP3606
RP3719
RPPKH2098
RPPKE1100
DESCRIPTION
CLEAR REPLACEMENT CAPSULE
TINTED REPLACEMENT CAPSULE
LOWER TRIM RING
DOME CLAMPING RING
NETWORK HGS POWER SUPPLY
24V HEATER
12V HEATER (12VDC MODELS ONLY)
BLOWER
CAMERA BRACKET 12VDC
CONNECTION PCB(24VAC)
CONNECTION PCB (12VDC)
HOUSING TOP
HOUSING TOP GASKET
WALL/PENDENT ADAPTER
WALL/PENDENT GASKET
LANYARD SET
WM11 WALL MOUNT
PENDENT MOUNT BRACKET
1 1/2 FEMALE /FEMALE COUPLING
BRACKET PACKET ASSEMBLY
ELECTRICAL PACKET ASSEMBLY
www.videolarm.com
© 2011, Moog Videolarm, Inc. All Rights Reserved
Camera Mounting Instructions
W81-IN5481
01-19-2012
NOTE:
!
For all RHP and RHW models a ½” (13mm)
spacer is added for additional height.
Für alles RHP und RHW modelliert eine ½“
(13mm) Distanzscheibe hinzugefügt für
zusätzliche Höhe.
Deutsch
English
Para todo o RHP e RHW modela um
espaçador do ½” (13mm) é adicionado para
a altura adicional.
Para todo el RHP y RHW modela un
espaciador del ½” (13m m) se agrega para la
altura adicional.
Español
Portuguese
Pour tous les RHP et RHW modèle entretoise
de ½ une » (13mm) est ajouté pour la taille
additionnelle.
Français
(HARDWARE)
(1)
Italiano
Per tutti i RHP e RHW modella un
distanziatore del ½„ (13mm) si aggiunge per
altezza supplementare.
(SPACING)
(1)
(1)
(88mm)
½”
1”
2”
(88mm)
½”
1”
2”
ACTi: ACM 8511
• Mounting holes
(4-M3)
(4)
ARECONT: AV8185 / AV8365 / AV20185 / AV20365
• Mounting holes
(4-#8 x ¾”)
(4)
(4)
(75mm)
1”
(100mm)
1”
2”
AVIGILON: HD-Dome Series
• Mounting holes
(3-#8)
(3)
(3)
1”
2”
AXIS: 215
• Mounting holes
(4-#8)
(4)
(4)
(100mm)
1”
(4)
(4)
(25mm)
1”
1”
2”
AXIS: 233D
• Mounting holes
(4-#8)
BASLER: BIP2-1000C-DN / BIP2-1300C-DN / BIP-D1000C-DN / BIP-D1300C-DN
• Mounting holes
(3-#8)
(3)
(3)
(100mm)
1”
1”
2”
CANON: VB-C60
• Mounting holes
(1)
(1)
(1)
(64mm)
½”
2”
(1)
(64mm)
½”
2”
(1)
(88mm)
½”
CANON: VB-M40
• Mounting holes
(1)
(1)
CANON: VB-C300
• Mounting holes
(1)
(1)
1”
2”
ELMO: PTC 400C
• Mounting holes
(4-#8)
(4)
(4)
(100mm)
½”
(38mm)
½”
1”
½”
2”
JVC: VN-V686BU / VN-V685U
• Mounting holes
(3-#8)
(3)
1”
PANASONIC: BB-HCM580/581
• Mounting holes
x
(1)
(1)
(1)
(88mm)
½”
1”
2”
PANASONIC: WV-CS580 Series
• Mounting holes
(4-#8)
(38mm)
½”
1”
PANASONIC: SC386
• Mounting holes
(4-#8)
(4)
(4)
(25mm)
(4)
(50mm)
1”
PANASONIC: WV-CS574
• Mounting holes
(4-#8)
(4)
2”
PANASONIC: WV-CS954 / WV-NS954
• Mounting holes
(4-#8)
(13mm)
(4)
½”
PANASONIC: WV-NS202 / WV-SC385 / WV-SC384
• Mounting holes
(4-#8)
(4)
(4)
(75mm)
1”
(3)
(25mm)
1”
PIXORD: P-463
• Mounting holes
(3-#8)
(3)
2”
SANYO: VCC-HD 5400
• Mounting holes
(2-#8)
(2)
(64mm)
2”
½”
SONY: EP / ER Series (520 / 550 / 580)
• Mounting holes
(4-#8)
(4)
(4)
SONY: RX Series (RX530 / RX550 / RX570)
• Mounting holes
(4-M3)
(4)
(38mm)
½”
1”
SONY: SNC RH/RS Series (RH124 / RS44 / RS46)
• Mounting holes
(4-#8)
(25mm)
(4)
1”
SONY: SNC-RZ25
• Mounting holes
(2-M3)
(2)
(1)
(1)
(1)
(13mm)
(1)
(1)
(1)
(50mm)
½”
SONY: SNC-RZ50
• Mounting holes
(2-M3)
(2)
2”
TOSHIBA: IK-WB16A
• Mounting holes
(1)
(1)
(1)
(88mm)
½”
2”
1”
TOSHIBA: IK-WB21A
• Mounting holes
(4-#8)
(4)
(4)
(75mm)
1”
2”
(75mm)
1”
2”
VIDEO IQ: VIQ-CT / CID / CRD / HD-CRD
• Mounting holes
(4-M4x10)
(4)
Product Registration/Warranty
Thank you for choosing Moog Videolarm. We value your patronage and are solely committed to providing you with the highest
quality products available and superior customer service. Should a problem arise, rest assure that Moog Videolarm stands behind its products by offering impressive warranty plans: 3 Years on all Housings, Poles, Power Supplies, and Accessories and 5 Years on camera systems (SView, QView, Warriors), and InfraRed Illuminators.
Register Your Products Online
Take a few moments and validate your purchase via the Online Product Registration Form at
www.videolarm.com/productregistration.jsp
Register your recent Moog Videolarm purchases and benefit from the following:
• Simple and Trouble-Free RMA process
• Added into customer database to receive product updates / news
• Eliminate the need to archive original purchase documents:
Receipts, Purchase Orders, etc…