Baumatic BFWE1420W User manual

BFWE1420W Washing
Machine
USER MANUAL FOR YOUR BAUMATIC
BFWE1420W
Washing Machine
You will be mine
NOTE: This User Instruction Manual contains important
information, including safety & installation points, which will
enable you to get the most out of your appliance. Please keep it
in a safe place so that it is easily available for future reference.
DD 19/10/06
2
Contents
Environmental note
4
Important safety information
5–6
Specifications
Description of the appliance
Control panel
LCD display
Program options
Detergent drawer
7
8
9
10
10-11
12
Preparing the wash cycle
Preparing your garments for washing
A selection of wash care symbols
Detergents and conditioners
13
13
14
15
Wash program chart
Wash program guidance
Selecting a wash program
At the end of the wash cycle
Cancelling a wash program
Changing a wash program
Delay start feature
Spin selection button
16
17
18
19
19
20
21-22
22-23
Maintenance and cleaning
In daily use
Control panel
Detergent drawer
The washing machine drum
Door
23
23
23
24
24
24
Error code failure system
General troubleshooting
Poor wash results
Cleaning the drain pump filter
25-26
27
28
29
Installation
Removing the transit bolts
Positioning and levelling the appliance
Water supply
Water outlet
Power supply
30
30
31
32
32
33
Baumatic Ltd. Conditions of Guarantee
Contact details
34
35
3
ENVIRONMENTAL NOTE
Note: Before discarding an old appliance, switch off and
disconnect it from the power supply. Cut off and render any plug
useless. Cut the cable off directly behind the appliance to prevent
misuse. This should be undertaken by a competent person. Disable
the door lock to make sure that children cannot get stuck inside
the appliance.
4
IMPORTANT SAFETY INFORMATION
Your safety is of the utmost importance to Baumatic.
Please make sure that you read this instruction booklet
before attempting to install or use the appliance. If you
are unsure of any of the information contained in this
booklet, please contact the Baumatic Technical
Department.
General Safety
o Repairs to your appliance must only be carried out by a
Baumatic engineer or one of its authorized service agents. Any
attempt by an inexperienced person to repair the appliance,
could result in injury or damage to your washing machine.
o If you notice that the mains cable is damaged. The appliance
must not be used. The same applies if you notice that the
worktop, control panel or base area is damaged. As this could
allow access to the internal components of the machine.
o The appliance should be turned off and isolated from the mains
supply, before either cleaning or maintenance work is attempted.
o The mains cable must not be used to pull the plug out of the
electrical socket.
o The machine should not be sprayed with water.
o The glass of the porthole door may become hot during the higher
temperature wash programs.
o The machine should be allowed to cool before carrying out an
emergency drain or cleaning the drain filter.
o It is possible for small animals to chew either mains cables or
water hoses, which could cause an electric shock hazard.
Installation
o The installation instructions contained within this user manual
should be followed.
o It is obligatory for the completed installation to comply with all
relevant building regulations and local water authority
requirements.
5
o Before the first use of the appliance, we advise that a 95
degree cotton wash is completed. No garments should be
placed inside the machine; however a small amount of
detergent must be used.
During Use
o It is recommended that the appliance is unplugged and the
water supply is turned off after the machine is used.
o This appliance is only designed to wash normal domestic
washloads. If you use your washing machine in any other way or
it is incorrectly used, then Baumatic accepts no liability for any
damage that might be caused and any guarantee will be void.
o No attempt should be made to alter or modify the specifications
of this appliance.
o The detergents that you place in this appliance should be
suitable for automatic washing machines. With regards to dosage
levels, the detergent manufacturer’s recommendations should be
followed.
o You should not wash garments that have been in contact with
flammable materials.
o Your washing machine should not be used for dry cleaning.
o If you use either dyes or bleaching agents inside this machine,
then you should consult with the manufacturer of these products
to make sure they are suitable for use in your washing machine.
Baumatic cannot be held responsible for any damages that may
result.
Child Safety
o Your washing machine should only be used by adults. You should
not allow children in the area of the machine unsupervised. You
should not let them touch the controls or play with the appliance.
o It could be possible for a child or pet to gain access to the
washing machine through the porthole door. Therefore please
check the drum before using the appliance.
o Any packaging that is removed from the machine should be kept
away from children.
o All detergents should be kept out of children’s reach in a safe
place.
6
Specifications
9 15 wash programs
9 5.5kg wash load
9 1400 rpm maximum spin speed
9 Drum size- 47 litres
9 Electronic control with LCD display
9 Delay start timer with remain time indicator
9 6 Option buttons:
Spin speed reduction
Easy ironing
Extra rinse (2 levels)
Rapid wash
Intensive wash
9 Unbalance control system
9 Foam protection
9 Suspend the clothes in water option
9 Overflow protection
9 Door closed indicator
9 Door safety lock
9 Tilted and stainless steel drum
9 Adjustable feet
9 Error code failure system
9 Aqua Spray rain shower effect. This additionally showers the
wash load throughout the wash cycle. It helps to improve the
wash and rinsing efficiency.
9 Cold water fill only
Dimensions
Energy efficiency
Height
Width
Depth
Energy rating A
Washing performance A
Water extraction performance B
: 850mm
: 595mm
: 505mm
7
Description of the appliance
1
2
3
4
5
6
Control panel
Detergent drawer
Porthole door with handle
Rating plate (on inside rim of porthole door)
Flap in front of the drain pump filter
Height adjustable feet
8
CONTROL PANEL
Wash program selection knob
This control knob allows you to select the wash program of your
choice.
Start/Stop button
Once a wash program has been selected, this button should be
pressed to start the wash cycle.
9
LCD display
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
LCD display
Easy ironing symbol
Rapid wash symbol
Intensive wash symbol
Spin speed indicator
Wash cycle end symbol
Spin selected indicator
Rinsing levels indicator
Delay start selected indicator
Washing phase indicator
Wash program progress indicator
Wash cycle start symbol
Wash time indicator and error codes display
Program options
¾ These buttons need to be pressed after a wash
program has been selected, but before the wash
program has been started.
Spin selection
You can select a different spin speed from the one automatically
selected by the machine for a particular wash program. On the
majority of wash cycles it is not possible to increase the spin speed
from the one originally selected by the appliance.
10
Extra rinse
The machine has two additional levels of rinsing. This will improve the
rinsing effect if you live in a hard water area or if you are washing the
clothes of a person who suffers from skin allergies. However it will not
increase the water consumption.
1)
Rinsing level one- press the extra rinse button once and the
machine will perform one extra rinse for the selected wash
program.
2)
Rinsing level two- press the extra rinse button twice and the
machine will perform five extra rinses for the selected
wash program.
The exceptions to this are the SPORT and REFRESHER wash
programs; on these the machine will perform three extra
rinses.
Easy ironing
Once the last spin has completed, the drum will move for several
minutes. This should help to reduce creasing in the garments being
washed.
Rapid wash
Press the Intensive/Rapid wash button once and the length of the
wash cycle will be shortened by approximately 30%. The machine
achieves this by reducing the number of rinse cycles by one.
Intensive wash
This option should be selected for garments that are very heavily
soiled. Press the Intensive/Rapid wash button once and the time it
takes for the wash cycle to complete will increase.
11
Detergent drawer
Pre wash section
I
This compartment should have detergent placed in, if you are going to
select a wash program that has a pre wash as part of it.
Conditioner section
This compartment should be used for liquid conditioners (fabric
softener, starch). They will be added to the wash load during the final
rinse.
Main wash section
II
This compartment should have detergent placed in it (you should also
put a water softening agent in this section, if you use one). The
detergent will be added to the drum at the start of the main wash
program.
12
Preparing the wash cycle
Preparing your garments for washing
o Your washing should be sorted out, according to the fabric type
and the wash care symbol that is printed on the garment’s wash
care label. (see separate section on wash care symbols).
o Check all pockets on a garment to make sure that they are
empty.
o Remove any detachable metal items (badges, paperclips, safety
pins etc).
o Zips should be closed, duvet covers and pillow cases should be
buttoned up and any loose straps should be tied up. This will
help to prevent other garments from getting damaged during the
wash.
o Woollens and knitted coloured fabrics should be turned inside out
before being washed in the appliance.
o Small delicate items (tights, baby socks) should be placed in
either a washing net or a zipped pillow case.
o Curtains should be handled with particular care. All plastic hooks
or metal strips must be removed before being washed in the
appliance.
o Coloured items and whites should be washed in separate wash
cycles.
o New garments often contain an excess of dye, therefore it is
advisable to wash them separately for their first wash.
o Garments should be unfolded and shook out before being placed
inside the machine.
13
A selection of wash care symbols
o The wash care symbols should be used to help you to select the
most suitable wash program. They will also help you to sort your
laundry into different loads, depending on the fabric type and the
highest temperature which the garment can be washed at.
o If the wash care label does not appear in the above table, then
please refer to the washing machine program chart. This gives
more detailed descriptions of the types of fabric that are suitable
to be washed using a particular wash program.
14
Detergents and conditioners
The amount of detergent that you need to use in your appliance, will
depend on
o The degree of soiling. Lightly soiled garments in general require
less detergent.
o The size of the wash load. A smaller wash load will require a
reduction in the amount of detergent.
o The hardness of your tap water. The harder your water is, then
the more detergent you will need to use. The detergent
manufacturers normally give guidance as to how much extra
detergent should be used, depending on the hardness of the
water.
Liquid detergent
If you are using liquid detergent, then in the majority of cases the
liquid should be placed inside the dosing device supplied by the
detergent manufacturer. All instructions on the detergent packaging
should be followed.
Water softening agents
If your tap water is hard, then it may be prudent to utilize a water
softening agent. This will help to ensure that the appliance does not
become clogged with hard water deposits. You may also find that it will
allow you to lessen the amount of detergent that you are using.
When using any detergent or water softening
agent, the recommendations of the
manufacturers should be followed.
15
16
Wash program guidance
o 1) A program option can only be selected if the wash program chart
indicates that this is possible.
o If you use the “Rapid wash” and Extra rinse” program options
simultaneously, then they will cancel each other out.
o The washing machine will automatically select a spin speed for a
particular wash program. However it is possible to alter the spin
speed by using the “Spin selection button”.
o Important: You should make sure that the selected spin speed is
appropriate for the garments that you are washing.
o If you use the spin selection button, you can make the machine not
go into a spin cycle. If you pick this option, then the machine will
stop with water in the drum.
o Important: Before opening the door of the appliance, you MUST
select the drain program to clear this water.
o 2) The LCD display shows an approximate time for the selected
wash cycle. Please note that factors external to the machine, e.g.
the temperature of your water supply, your water pressure etc. can
affect the time it takes for the wash cycle to complete.
o The “Level of fill” section of the program chart, gives an indication
of how full you should fill the drum on each specific wash program.
17
Selecting a wash program
9 Load your laundry and put detergent in the relevant
compartment of the soap drawer.
9 Close the porthole door firmly.
9 Turn the wash program selection knob to your desired wash
cycle.
o The LCD display will show the approximate time the chosen wash
cycle will take to complete.
9 Select any relevant program options using the four buttons
underneath the LCD display. The program option symbols that
you have selected will appear on the LCD display.
9 If required, make alterations to the spin speed by using the Spin
Selection button.
o Any program options that you select, will affect the length of
time that the wash cycle will take to complete. The LCD display
will update to reflect this change.
9 Press the Start/Stop button.
o The LOCK DOOR light will go out
o After approximately 5 seconds, you will hear your washing
machine start the wash cycle.
o The wash program progress indicator will advance on the LCD
display as the wash program progresses. When the wash and
rinse stage of the wash cycle have completed, the corresponding
symbols will disappear from the LCD display.
o If there is a power failure or the plug is pulled out of the
socket when a wash cycle is in progress. Once power has
been restored, the wash program will continue.
o If the power is cut to the machine or the wash program
selector knob is turned to the off position and more than
one minute elapses. The door lock will no longer be
engaged and it will be possible to open the porthole door
of the appliance. You should take care not to open the
door whilst there is still water inside the drum.
18
At the end of the wash cycle
o Once the washing machine has completed its cycle, STOP will
show on the LCD display. The door lock light will remain off for
one minute; this indicates that the door is still locked.
o After one minute the LOCK DOOR light will turn on. At this point
it is possible for you to open the door and take out the washload.
You should not attempt to open the door until
the LOCK DOOR light is lit.
Cancelling a wash program
9 To stop a wash program once a wash cycle is in progress, press
and hold the START/STOP button until the LCD display changes
back to the screen that you see when originally selecting a wash
program.
o The door lock light will remain off for one minute; this indicates
that the door is still locked.
o After one minute the LOCK DOOR light will turn on. At this point
it is possible for you to open the door and take out the washload.
Before opening the porthole door, you MUST
select the DRAIN program. Otherwise there
may still be water in the drum when you
open the door.
o Turn the wash program selection knob to the off position.
19
Changing a wash program
o If you have accidentally selected the wrong wash program, then
it is possible to change it to the correct one.
9 Press the START/STOP button to interrupt the wash cycle.
9 Turn the program selection knob to the wash program that you
wanted to select originally.
9 Select any relevant program options using the four buttons
underneath the LED display.
9 Press the START/STOP button.
Please note that this process must not be
used to cancel a wash program. You should
follow the “Cancelling a wash program”
section to do this.
o If the program selection knob is turned mid wash cycle without
the “Changing a wash program” process being followed. Then
the originally selected wash program will continue and complete
as normal.
o The LCD display will show the letter P and the number of the
wash program that you originally selected.
20
Delay start feature
Your appliance has a delay start feature, which allows you to pause
the start of a wash cycle until a later time.
9 Follow the process listed under “Selecting a wash program”
9 After pressing the Start/Stop button, immediately press the
Start/Stop button again.
o The LCD display will show 1.00 (indicating that the wash cycle
will start in one hours time).
o If you continue to press the Start/Stop button, then the time
delay will increase in 30 minute intervals until 3.00 appears on
the LCD display.
o If you continue to press the Start/Stop button, then the time
delay will increase in 1 hour intervals. The LCD will continue to
increase in one hour intervals until it reaches twenty fours hours.
The LCD display will then show 24h.
o If you press the Start/Stop button once more, then it will return
to 0.00 and no delay start will be set on the machine.
9 Once the LCD display shows the delay interval that you require,
let go of the Start/Stop button.
9 After a few moments the LCD
display will show the delay start
interval that you have selected,
the spin speed of the wash
program selected and any
program options that have been
selected.
9 The machine should not be turned off at this stage as the delay
start will not be remembered by the machine when it is switched
back on.
o The LOCK DOOR light will turn off.
9 Once a delay start has been set, you cannot alter the delay
interval without cancelling it.
21
9 To cancel the delay start feature, you should press and hold
down the Start/Stop button until the LCD display changes back
to the screen that you see when originally selecting a wash
program. You can then select another wash cycle that will start
immediately or you can set up the delay start feature to operate
again.
o After a delay start has been cancelled, the door lock light will
remain off for one minute; this indicates that the door is still
locked.
9 When the LOCK DOOR light switches on, it will then be possibly
for you to open the porthole door.
Spin selection button
Your washing machine will automatically select an appropriate spin
speed for each wash program. However it is possible to alter the
spin speed that it automatically selects, by pressing the spin
selection button.
9 Turn the wash program selection knob to the wash program
that you want to use.
9 Press the spin reduction button and continue to press it until
the LCD display shows the spin speed that you require.
o On wash programs where 1000 rpm is automatically selected,
the speed in the LCD display will change as follows;
1000-900-800-700-600-500-400-1001400-1300-1200-1100
-
.-
o On wash programs where 600 rpm is automatically selected,
the speed in the LCD display will change as follows;
600-500-400-100-
-
.
9 If you continue to press the spin reduction button after
100rpm appears. Then
will appear in the display.
This symbol means that the appliance will not spin and it will
move to the drain program after the rinses have completed.
9 If you press the spin reduction button again, then
will
appear in the LCD display. This means that the clothes will be
held in water, until you select a spin or drain program.
YOU MUST DO THIS BEFORE OPENING THE DOOR OF
THE APPLIANCE.
22
o This feature is useful if you are not going to be present when
the wash cycle completes, as it will lessen the chance of the
garments becoming creased.
Please note that if you suspend the clothes in
water, you must select a spin or drain program and
not just cancel the program. Otherwise you could
open the porthole door whilst there is still water
in the drum.
You should ensure that the garments you are
washing are suitable for suspending in water
before selecting this option. Garments should not
be suspended in water for a prolonged period.
Maintenance and cleaning
In daily use
9 Once a wash cycle has completed, you should pull out the
detergent drawer slightly, so it can dry out.
9 Leave the porthole door ajar for a short while after a wash
cycle has completed. This should help to prevent stagnant
smells and to protect the door seal.
9 Close the water tap.
9 We suggest that you disconnect the appliance from your
mains supply, when it is not in use.
Control panel
IMPORTANT: Do not use any abrasive cleaner or household polish on
either the control panel or operating parts.
9 Wipe over the control panel using a brand new damp cloth
with warm water.
23
Detergent drawer
Occasionally the detergent drawer should be cleaned.
9 Clean the area that the detergent drawer slides into with a
brush.
The washing machine drum
The drum of your washing machine is constructed from stainless steel.
However if there are objects that can rust placed inside the drum, then
it is possible for the drum to become stained.
IMPORTANT: Do not use a descaling agent, iron/steel wool or
scouring agents to clean the drum of your appliance.
9 Remove any rust stains on the drum with an appropriate
stainless steel cleaning agent.
Door
9 You should regularly check to see if any deposits have
formed, or there are any foreign bodies in the rubber door
gasket. This sits inside the opening of the porthole door.
24
Error code failure system
If your appliance senses that it is not operating correctly, then an error
code may appear in the LCD display.
The following error codes can possibly be remedied by the customer
and the steps outlined below should be followed.
BEFORE COMPLETING ANY MAINTAINEANCE ON THE
APPLIANCE, IT SHOULD BE DISCONNECTED FROM YOUR MAINS
POWER SUPPLY.
NO DISPLAY
o Power failure.
9 Check that the power plug is in the mains socket correctly.
9 Check the mains fuse.
E01
o The door is not closed.
9 Close the door firmly.
E02
o Low water pressure.
9 Check the water pressure of your mains water supply.
9 Clean the mesh filter that sits in the inlet hose.
9 Make sure the water tap that the machine is connected to is turned
on fully.
E03
o Pump filter clogged.
9 Clean the filter.
E04
o The washing machine is overloaded.
9 Clean the pump filter.
9 Reduce the wash load.
E05
o No water in the washing machine.
9 Make sure the water tap that the machine is connected to is turned
on fully.
9 Clean the mesh filter that sits in the inlet hose.
E06
o The water was not pumped out.
9 Clean the drain pump filter.
9 Check the drain hose is not blocked or kinked.
25
E09
o The appliance has recognised a foam surplus, therefore the wash
cycle completes without spinning.
9 To get the soap suds out of the clothes, the rinses and conditioning
program should be selected. Do not put any detergent in the
machine for this wash cycle.
Once the machine has been plugged back into your mains power
supply, to clear the fault code from the LCD display, you should turn
on the machine and hold down the Start/Stop button for approximately
5 seconds.
IF THE FAULT CODE REAPPEARS AFTER
FOLLOWING THE ABOVE ADVICE AND CLEARING
THE FAULT CODE. YOU SHOULD TURN THE WASH
PROGRAM SELECTION KNOB TO THE OFF
POSITION; DISCONNECT THE APPLIANCE FROM
YOUR MAINS SUPPLY. THEN ARRANGE FOR AN
ENGINEER TO ATTEND THE APPLIANCE. YOU
SHOULD CONTACT BAUMATIC SERVICE ON
TELEPHONE NUMBER (0118) 933 6911.
IF AN ENGINEER ATTENDS DURING THE
GUARANTEE PERIOD AND FINDS THAT A FAULT
HAS BEEN CAUSED BY AN ITEM ON THE ERROR
CODE LIST, WHICH COULD HAVE BEEN CLEARED BY
THE CUSTOMER. THEN YOU MAY BE LIABLE FOR
THE COST OF THE SERVICE CALL.
26
General troubleshooting
Water under the washing machine
9 Tighten the drain pump filter.
9 Check the drain and inlet hose and make sure that it is fully
tightened.
Washing machine vibrates during the spin cycle
9 Check that the transport locking devices have been removed (see
installation instructions).
9 Make sure that the washing machine is installed on a flat and level
floor.
9 Ensure that all four feet are resting firmly on the floor, by pressing
down on each corner and making sure that the appliance is stable.
9 If it is unstable then slacken off the lock nuts and adjust the feet to
level off the machine. Tighten the locknuts up fully once the feet
have been leveled.
Poor spin results
9 Clean the drain pump (see “Cleaning the drain pump filter” section).
IMPORTANT: Your appliance has an unbalance control system. If this
system detects that the washload is unevenly distributed inside the
drum. Your washing machine will try to redistribute the load before
spinning. If after several attempts it is unable to redistribute the
washload, then the appliance will either spin at a slower speed or skip
the spin cycle and drain.
Uneven load distribution can be caused by too large a wash load or too
small a wash load. It can also occur if a single item if washed inside
the appliance.
Excessive foam formation
9 Check your water hardness and adjust the detergent dose
accordingly.
27
Poor wash results
My garments are looking grey and there are limescale
deposits present in the drum of my washing machine.
o There is not enough detergent being added.
o The incorrect detergent is being used.
o Stains are not being pre-treated.
o The correct wash program or wash temperature was
not selected.
I have followed the advice given above, but my
garments are still coming out with grey stains on them.
o The garments are soiled with oils, ointments or grease
and were washed without enough detergent.
o The wash temperature selected was too low.
o Fabric conditioner has come into contact with the
garments. If this happens try to wash out these stains
as quickly as you can and try to avoid getting
conditioner on the garments in future.
After the final rinse, I can still see foam.
o Modern detergents can result in there still being foam in
the final rinse, this does not mean that the washing is
not being rinsed properly.
There is white residue on my garments when I remove
them from the appliance.
o Modern detergents can contain insoluble contents and
white residue after a wash cycle is not necessarily a
sign of the garments not being rinsed properly.
You should shake out the garment or brush it off. In
future possibly turn the garment inside out before it is
washed. You may wish to move from a powder
detergent and switch to a liquid detergent instead.
28
Cleaning the drain pump filter
IMPORTANT: Switch off your washing machine and
disconnect the plug from your mains supply.
You should clean out the filter approximately every twenty
washes. If the drain pump filter is not cleaned regularly, then
your appliance may find it difficult to pump out water
efficiently.
29
Installation
IMPORTANT: THIS INSTALLATION MUST BE
COMPLETED BY A SUITABLY QUALIFIED PERSON.
BAUMATIC ONLY SANCTION THE INSTALLATION
GIVEN IN THIS INSTRUCTION MANUAL. YOU
SHOULD KEEP THE TRANSIT PACKAGING, IN CASE
YOU NEED TO TRANSPORT THE MACHINE IN THE
FUTURE.
Removing the transit bolts
9 Using a screwdriver, unscrew
and remove the 4 outer screws
(a) that are securing the
transit support bar to the
machine.
9 Using a spanner, unscrew and
remove the 3 transit bolts (b)
that secure the drum in
position whilst the washing
machine is being transported.
9 Remove the transit support bar
(c).
Place the supplied plastic stoppers into
the holes on the back of the machine,
which have been left by the removal of
the transit bolts.
IMPORTANT: The transit bolts and
transit support bar MUST be removed
before your washing machine is used for
the first time.
30
Positioning and leveling the appliance
9 Place the washing machine on a solid
and level floor surface.
9 DO NOT PLACE THE WASHING
MACHINE ON A CARPET.
9 Slacken off the lock nut on each of the
washing machine feet using a
spanner.
9 Adjust the feet to level off the
washing machine.
9 Tighten up the lock nut on each of the
washing machine feet using a
spanner.
IMPORTANT: When the washing machine is positioned in the location
where it will be used. Make sure that all four feet are resting firmly on
the floor, by pressing down on each corner and checking that the
appliance stands still.
31
Water supply
9 Connect and fully tighten the inlet hose to the top right hand corner
of the washing machine.
9 Connect the other end of the inlet hose to your mains water supply
9 IMPORTANT: There should be a filter that sitting inside the end of
the inlet hose that connects to your mains water supply. The inlet
hose may leak if this filter is missing. This filter is supplied with the
appliance, you should contact Baumatic to obtain one, if it is
missing.
9 Tighten the inlet hose to your mains supply fully, but do not over
tighten as this may distort the filter that sits in the end of the inlet
hose.
9 Test for any leaks.
Water outlet
9 Secure the drain hose, so that it cannot move whilst the washing
machine is in use.
9 Place the end of the drain hose on your drain pipe. Push it a
short way down into your drain pipe.
9 IMPORTANT: Do not insert the drain hose too deeply into the
water pipe, as this may cause siphoning.
9 NEVER EXTEND THE DRAINAGE HOSE FROM ITS ORIGINAL
LENGTH.
32
Power supply
9 The moulded plug that is supplied with the appliance, must be
placed into an earthed and insulated socket.
9 Broken power leads must only be replaced by a suitably qualified
person.
9 Power lead type – H 0 V V – F 3G 1,5.
9 IMPORTANT: We do not recommend that this appliance is
connected to an extension lead.
33
Baumatic Ltd. Conditions of Guarantee
Dear Customer,
Your new Baumatic appliance comes complete with a free 12 month guarantee covering both parts and
labour costs resulting from defective materials or workmanship.
Baumatic also gives you the opportunity to automatically extend the guarantee period for a further 12
months at no extra cost, giving an initial guarantee period of 24 months. The extended guarantee period
applies to England, Scotland, Wales and Northern Ireland only.
To qualify for your full 24 months guarantee you must register your appliance within 28 days of purchase
to be covered under this guarantee. This can be done online via: www.baumatic.co.uk or through returning
the guarantee card which can be found in each new Baumatic appliance.
* In addition, your appliance is covered by a 5 year parts warranty. Baumatic Ltd will provide free of
charge the parts required to repair the appliance, only if they are fitted by a Baumatic engineer, for any
defect that arises due to faulty materials or workmanship within a period of 5 years from the original
purchase date.
* An additional 1 to 3 year insurance scheme for labour is available should you wish to extend the
warranty period.
Should any person other than an authorised representative of Baumatic Ltd interfere with the appliance, the
policy is negated and Baumatic Ltd will be under no further liability.
The guarantee covers the appliance for normal domestic use only, unless otherwise stated.
Any claims made under the terms of the guarantee must be supported by the original invoice/bill of sale
issued at the time of purchase.
This guarantee is transferable only with the written consent of Baumatic Ltd.
If the appliance fails and is considered either not repairable or uneconomical to repair during the
manufacturer warranty period, a free of charge replacement will not be offered.
The guarantee for any replacement will only be for the remainder of the guarantee on the original product
purchased.
The guarantee does not cover:
- Sinks and taps
- Failure to comply with the manufacturers instructions for use.
- The replacement of cosmetic components of accessories
- Accidental damage or wilful abuse.
- Subsequent loss or damage owing to the failure of the appliance or electrical supply
- Incorrect installation
- Losses caused by Acts of God, civil war, failure to obtain spare parts, strikes or lockouts
- Filters, fuses, light bulbs, external hoses, damage to bodywork, paintwork, plastic items, covers,
baskets, trays, shelves, burner bases, burner caps, decals, corrosion, rubber seals.
In the course of the work carried out it may be necessary to remove the appliance from it operating
position. Whilst all reasonable care will be taken, Baumatic Ltd cannot accept responsibility for damage
sustained to any property whatsoever in this process.
This guarantee is in addition to and does not diminish your statutory or legal rights.
Contacting Baumatic Ltd
Sales
Service
Spares
TEL: 0118 933 6900
TEL: 0118 933 6911
TEL: 0118 933 6922
FAX: 0118 931 0035
FAX: 0118 986 9124
FAX: 0118 933 6942
For ROI (Republic of Ireland), please contact one of the numbers below:
TEL: 01 – 6266798
FAX: 01 - 6266634
Technical/Advice
0118 933 6933
0118 933 6942
Thanks you for buying Baumatic.
* Applies to UK, Scotland, Wales & Northern Ireland only (Republic of Ireland has 1 year labour & 1 year parts warranty only)
34
Baumatic Ltd
Make-up for your kitchen
Headquarters
Baumatic Ltd.
Baumatic Buildings,
6 Bennet Road,
Reading,
Berkshire
RG2 0QX, United Kingdom
Sales Telephone
+44 118 933 6900
Sales Fax
+44 118 931 0035
Service Telephone
+44 118 933 6911
Service Fax
+44 118 986 9124
Spares Telephone
+44 118 933 6922
Technical / Advice Telephone
+44 118 933 6933
E-mail:
sales@baumatic.co.uk
technical@baumatic.co.uk
Http (Internet site):
www.baumatic.com
35
36