Daewoo DWF-5511 Instruction manual

=
INSTRUCTION MANUAL
TABLE OF CONTENTS
■SAFETY INSTRUCTIONS &
SPECIFICATIONS ..........................................2
■PARTS DESCRIPTIONS................................3
■DIRECTIONS FOR SAFE USE .....................4
•How To Install.................................................4
•Water Connection ..........................................6
•Drain Hose Setting.........................................7
■HOW TO OPERATE .......................................8
• Preparation for Washing ...............................8
• Descriptions of Control Panel .......................9
• General Procedures for Operation .............10
• Guides for Basic Washing Programs .........11
• Guides for Other Useful Programs.............13
■PERIODIC MAINTENANCE ........................14
■SPECIAL GUIDES FOR REMOVING STAINS ...16
■TROUBLE SHOOTING GUIDES.................17
※ PLEASE READ CAREFULLY THIS INSTRUCTION
MANUAL BEFORE USING YOUR WASHER AND
SAVE THIS FOR FUTURE REFERENCE.
Model: DWF-5510/5511
5520/5521
6010/6011
6020/6021
;;
;;
SAFETY INSTRUCTIONS & SPECIFICATIONS
SAFETY INSTRUCTIONS
※ Your safety is important to us.※
Read all instructions before using your washer.
☞ Do not wash items cleaned, washed, soaked in, or spotted with wax, paint, gasoline, oil, or other flammable
fluids. The fumes can create a fire hazard or explosion.
☞ Flammable fluids (dry-cleaning solvents, kerosene, gasoline, etc.) should not be used or stored in or near
your washer. Do not add flammable fluids to your wash water. These substances give off vapors that can
create a fire hazard or explosion.
☞ Do not allow children to operate, play with, or crawl on or inside your washer.
Supervise children closely when your washer is used near them.
☞ Do not reach into the wash tub unless START/HOLD button is pressed and all motion stops, while spinning.
☞ Do not use chlorine bleach and ammonia or acids (such as vinegar or rust remover) in the same wash.
Hazardous fumes can form.
☞ Unplug power supply cord before attempting to service your washer.
☞ Do not pour water on the control panel.
☞ Remove foreign objects (such as coin, pin, knife, other metallic materials, etc.) inside your wash load.
They may damage any fabric.
☞ Do not overload your washer to avoid poor cleaning, wrinkling and/or any abnormal operation.
SPECIFICATIONS
MODEL NO
DWF-5510 DWF-5511 DWF-5520 DWF-5521 DWF-6010 DWF-6011 DWF-6020 DWF-6021
Power Source
Please refer to the rating label at the back of your washer.
Power Consumption
250W
Width ✕ Depth (mm)
532 ✕ 542
Height (mm)
855
920
877
952
855
920
887
952
Net Weight (Kg)
32
32.5
32.5
33
32.5
33
33
33.5
Maximum Mass of Textile
5.5kg
6.0kg
Material of Internal Tub
Recyclable Poly Propylene
Anti-Rust Stainless Steel
Water Consumption
Approx. 135 Liters/Cycle
Approx. 130 Liters/Cycle
Washing Capacity
Please refer to the rating label at the back of your washer.
Washing Program
4 Programs
Water Level
High (55 Liters), Medium (45 Liters), Low (31 Liters)
Direction of Inlet Valve
Backward
Upward
Backward
Upward
Operating Water Pressure
0.3Kgf/cm2~8Kgf/cm2 (2.94N/cm2~78.4N/cm2)
Pulsator
Provided with 6 Spouting Holes for Powerful Upward Water Stream
1. Air Bubble Generator
Optional Features
2. Reserved Washing with Display for remaining time
3. Signal Buzzer for the Operation of Control Button
Coin Filter
Only in Pump Model identified with ‘P’ added to Model No. (e.g., DWF-5510NP)
※ The above specifications and features are subject to change without prior notice.
2
PARTS DESCRIPTIONS
DETERGENT CASE (Symbol
WATER CONNECTOR
(Blue Color: Cold,
Pink Color: Hot)
)
FABRIC SOFTNER INLET
(Symbol, See page 10)
DOOR
DRAIN HOSE
LIQUID BLEACH INLET
(Symbol, See page 10)
LINT FILTER
CONTROL PANEL
(88 display and some
buttons may be excluded)
WASH TUB
PLUG
GROUND WIRE
(This will not be
provided in
case of 3-wire
power cord)
PULSATOR
;;
BASE
(Height is optional)
ADJUSTABLE LEG
(Optional)
◆ The drawings in this book may vary from your washer model. They are designed to show the
different features of all models covered by this book. Your model may not include all features.
ACCESSORIES
Dryten
(option)
Under Cover
(option)
Hose Adapter
UP
In case of screw-shaped inlet hoses water
tap adapters will not be provided.
Inlet Hose
(option)
Drain Hose
Non-Pump Model
Pump Model
3
Hose Clamp
;;
DIRECTIONS FOR SAFE USE
HOW TO INSTALL
Location
Place your washer on a level and solid floor,
considering the length of inlet hose, drain
hose and power supply cord.
If washer is not level, it should be corrected
by the adjustable leg (provided optionally) in
the front-right side under the base and/or, a
thin block or brick.
Do not place or store your washer below 0°C(32°F) to avoid
any damage from freezing.
Do not place your washer where it may be splashed during
bathing.
NOTES:
The opening muse not be obstructed by carpeting when
the washing machine is installed on a carpeted floor.
Installation of the Under Base Cover (Option)
-DWF-5510/5511/6010/6011
After installing the washing machine, assemble
the under-base cover.
installing your washer, remove the
å Before
pad from the bottom of the cabinet.
the under-base cover into the end,
∫ Push
which decrease the noise made by this
Then, separate under cover from rear side
of cabinet by unscrewing and insert it into
the base.
washer.
SCREW
-DWF-5520/5521/6020/6021
the packing box is opened, there is
å After
a under-base cover at the top of
∫ Push the under-base cover into the end,
the washer.
which decrease the noise made by this
washer.
4
Power Supply
* Before plugging the plug into wall
receptacle, check the voltage rating is
in the range of rating, marked on the
label at the back side of your washer.
LABEL
Grounding
• If your water tap or water pipe
is not made of metal, connect
the ground wire to a copper
plate or a metal rod and bury
it in the earth.
• If both your water tap and
water pipe are made of metal,
connect the ground wire to the
base of the water tap.
• In case of using 3-core cord,
there is no need for
grounding.
• It is of no use connecting the
ground wire to the water pipe
made of plastic.
20Cm
Never Connect the Ground Wire to Such a Thing
• Never connect it to a gas pipe because of danger
of a explosion.
• Never connect it to a telephone wire or a lightning
rod because of os very dangerous at a
thunderbolt.
Gas Pipe
Telephone Wire
5
;;
WATER CONNECTION
Be careful not to confuse hot water inlet (pink color) and cold water inlet (blue color),
if your washer is provided with dual water inlets.
Also if you have only one water tap, connect the inlet hose with cold water inlet (blue color).
For normal tap
! Pull down the collar of the
inlet hose to separate it
from the hose adapter.
@ Loosen the four screws
properly in fitting into
water tap.
# Fit the hose adapter into the water
tap and tighten the four screws
evenly while pushing up the
adapter so that the rubber packing
can stick to the water tap tightly.
TAPE
$ Remove the tape, and
screw connector B into
connector A tightly.
% Connect the inlet hose to
the hose adapter, pulling
down the collar of hose
end.
^ Connect the opposite end
of the hose to water inlet
of your washer tightly.
• Please check the rubber
packing is inside the
hose end.
Connector A
Connector B
* In case that your washer is not provided with collar compartment, procedure # and % is not
necessary.
For Thread-Fitting Type
! Connect the inlet hose to the thread of
water tap or water pipe by tightening.
Connector
@ For the opposite end, connect it to water
inlet as the above procedure ^.
Rubber
Packing
Hose
Connector
Leak Test
Turn on the water completely to check for any leakage. If any leakage, turn off the water, try
again as the above procedures.
For the special tap, call a qualified plumber for the installation.
6
;;
DRAIN HOSE SETTING
Before operating your washer, install drain hose properly.
First, connect the drain hose to the drain outlet at the
rear side of your washer, and then fasten it tightly with
the hose clamp.
Next, the other end of drain hose set as the below.
Pump Model
! Connect the drain hose to the drain outlet
at the rear side of the washing machine,
and fasten it tightly with the clamp
supplied.
@ Attach the hose guide included in the
accessory kit, to guide the drain hose over
the tub or standpipe.
PULL HOSE
THROUGH
55mm
FLEX HOSE
GUIDE
APART
# Hook the drain hose to the edge of
the tub, paying attention that there
are no bends or constractions
along the drain hose.
Or, connect the drain hose to a standpie
of a diameter greater than that of the drain
hose and at a height of min. 70cm.
$ Attach the hose guide included in the
accessory kit, to guide the drain hose
over the tub or standpipe.
70Cm min
MUST be
ventilated
NOTES
1. Let the highest point of the drain hose be more than 1m above the floor.
If not so, the water in the washer could be drained during operation.
2. Be sure that the height of the drain hose must be less than 1.4m above the floor. If not so, the wart in the washer could not drain.
3. The hose guide MUST be fitted to the drain hose. The drain hose should not extend more than 55mm from the end of the hose
guide. This is to prevent ‘SYPHONING’. If necessary the drain hose can be trimmed to length.
Non-Pump Model
! In case that it goes over a
door sill. Don’t let the height
of the drain hose exceed
20cm from the ground.
@ In case of extending the
drain hose. Don’t let the
total length exceed 3m.
3m
20Cm
7
# Be careful that the end of
the drain hose is not
immersed in water.
;;
HOW TO OPERATE
PREQARATION FOR WASHING
To obtain the best washing results, you must operate your washer properly.
This section give you this important information.
Preparing clothes for washing
• Close zippers, snaps, and hooks to avoid
snagging other items.
Remove pins, buckles, and other hard
objects to avoid scratching the washer
interior.
• Empty pockets and turn them inside out.
• Turn down cuffs and turn synthetic knits
out to avoid pilling.
• Tie strings and sashes so they will not
tangle.
• Treat spoats and stains.
(see “Special Guides for Removing stains”
on page)
Sorting
• Separate heavily soiled items from, lightly soiled ones, even if they would normally be
washed together.
• Separate dark colors from light colors, colorfast items from non-colorfast item.
Loading
• Mix large and small items in each load.
Load evenly to maintain washer balance.
An off balance load can make the washer
vibrate during spin.
• Reduce wash time when using a small load
size setting. Loads with only a few small
items need less wash time.
• Use a large load size setting to reduce
wrinkling with permanent press clothes and
some synthetic knits. These items should
have more room to move in the water than
heavy items (towels, jeans)
• Drop items into washer loosely. Items
should move easily through wash water for
best cleaning and wrinkle-free results.
• Load washer properly and select correct
load size setting.
Overloading and selecting a setting too
small for the wash load can:
- cause poor cleaning
- increase wrinkling
- create excessive lint
- wear out items faster (because of pilling)
8
;;
DESCRIPTIONS OF CONTROL PANEL
DWF-5510/5511/6010/6011
HIGH
MID
POWER
°°
FUZZY
ADD
LIGHT
WASH
HEAVY
RINSE
START
/ HOLD
HOT
COLD
LOW
RES.
WA
T
LEV ER
EL
RES.
WOOL/SUIT
SPIN
COURSE
PROCE
P
TEM
SS
DWF-5520/5521/6020/6021
HIGH
POWER
MID
°°
FUZZY
ADD
LIGHT
WASH
HEAVY
RINSE
WOOL/SUIT
SPIN
START
/ HOLD
HOT
COLD
LOW
RES.
WA
T
LEV ER
EL
RES.
COURSE
PROCE
SS
P
TEM
POWER
Power Switch
Press this button to turn the power ON or OFF.
WATER
LEVEL
Water Level Selector
This button is used to select the water level you want.
RES.
COURSE
PROCESS
Reservation Button
If you want to reserve the finishing time of washing, use this button.
As this button is pressed, digit in display increases by 1 hour at one press.
If current time is 8:00 am and you expect washing will be completed around 5:00
pm, press this nine times in order to display ‘9’.
Course Selector
This button is used to select the washing course according to the type of wash
loads.
Either Wool or Suit course is adopted to your Washing Machine.
Program Button
With this button, you can create new programs by combinations of process.
TEMP
Temperature Selector (Optional)
If your washer is connected to two water taps for cold water and hot water, you
can select them. Without operation, cold water would be selected automatically.
START
/ HOLD
Start/Hold
With this button, you can make your washer proceed your program, or stop temporarily.
And you can also release the temporary stop by pressing this.
9
;;
GENERAL PROCEDURES FOR OPERATION
1. Add measured detergent to the washer, (Follow manufacturer’s directions for safe use)
2. OPTIONAL STEP
If desired, add measured liquid chlorine bleach to the bleach inlet. use only liquid chlorine in
the bleach inlet
* Follow manufacturer’s direction for safe use.
Bleach inlet
(Symbol)
NOTE
• Do not let bleach splash, drip, or run down into washer
basket.
Undiluted bleach will damage any fabric it to touches.
• Do not use this dispenser to add powdered chlorine or
color safe bleach to your wash load. The dispenser is for
liquid chlorine bleach use only.
3. OPTIONAL STEP
If desired, add measured liquid fabric softener to the softener inlet.
• Pour liquid fabric softener into the dispenser using the amount recommended on the
package. Avoid dripping or spilling any fabric softener on the load.
• The dispenser is for liquid fabric softener use only.
Softener inlet
(Symbol)
4. Close the washer lid (door)
5. Press the power button.
6. Select the course. The full automatic course has four settings; FUZZY, LIGHT, HEAVY, SUIT.
(See page 9)
7. Press the “START/HOLD” button.
10
;;
GUIDES FOR BASIC WASHING PROGRAMS
Fuzzy Course
• This course is a washing method for the general clothes except the extraordinary clothes such
as blanket, wool, etc
! Put in the clothes
@ Press the power switch.
# Press the Start/Hold
button, and close the lid.
START
/ HOLD
POWER
Light Course
• This course is effective for the washing of light clothes or lightly stained clothes.
• Regulate the water level according to the wash load.
! Press the power
switch.
@ Press the course
selection button
for “LIGHT”
# Select the water
level proper to the
wash load.
$ Press the
Start/Hold button,
and close the lid.
FUZZY
HIGH
LIGHT
MID
HEAVY
POWER
LOW
WOOL
START
/ HOLD
WATER
LEVER
COURSE
Heavy Course
• This selection is effective for blue-jean, climbing clothes, ruck sack, sports wear.
! Press the power
switch.
@ Press the course
selection button
for “HEAVY”.
# Select the water
level proper to the
wash load.
$ Press the
Start/Hold button,
and close the lid.
FUZZY
HIGH
LIGHT
MID
HEAVY
POWER
LOW
WOOL/SUIT
WATER
LEVER
COURSE
11
START
/ HOLD
Wool Course (Option)
• This selection is effective for wool clothes.
(1.2kg's limitation for 1 time-wash)
• Do not put leather clothes, or chamois clothes into the washing tub for washing. It may cause
shrinkage or deformation to the clothes.
• Please use the neutral detergents only.
• The water temperature is fixed to "COLD"
• The water level "LOW" is not select.
! Press the power
switch.
@ Press the course
selection button
for “WOOL”
# Select the water
level proper to the
wash load.
$ Press the
Start/Hold button,
and close the lid.
FUZZY
HIGH
LIGHT
MID
HEAVY
LOW
WOOL
POWER
START
/ HOLD
WATER
LEVER
COURSE
Suit Course (Option)
• This selection is effective for
High-quality sweater, wool etc..
(1kg’s limitation for 1 time-wash)
• Put in the wash market with
“Dry Cleaning”.
• Use detergent that is “Only for Dry Cleaning”.
• The water temperature is fixed to “COLD”.
• The water level "LOW" is not select.
! Press the power
switch.
@ Press the course
selection button
for “SUIT”.
FUZZY
LIGHT
HEAVY
START
/ HOLD
SUIT
COURSE
# Select the water
level proper to the
wash load.
$ Press the
Start/Hold button,
and close the lid.
% Put the clothes into
the tub after the
buzzer sounds.
^ Press the
Start/Hold button,
and close the lid.
HIGH
MID
LOW
START
/ HOLD
START
/ HOLD
WATER
LEVER
12
;;
GUIDES FOR OTHER USEFUL PROGRAMS
For the partial process or the combinations, or for adding time of each process.
step 1. Press power switch.
step 2. Press program button until the indicaing lamps make the combinations you want.
If only spin lamp is turned on, that means you will operate your washer for spin only.
If rinse and spin lamp are turned on, that means you will operate your washer for rinse and spin.
If add lamp is turned on with other process lamps, that means the time of the corresponding
process will increase by 1~2 minutes, that is, if add is on with wash, rinse and spin, the time of each
process will increase by 1~2 minutes. (Wash: add 2 min., Rinse: add 1 min., Spin: add 1 min.)
step 3. Press water level selector as your decision.
step 4. Press Start/Hold to start.
! Pressing
the Power
Switch
@ Selecting
Water level
Wash & Rinse
& Spin
ADD
WASH
RINSE
SPIN
Only Spin
ADD
WASH
RINSE
SPIN
Add & Wash
ADD
WASH
RINSE
SPIN
Add & Rinse
& Spin
ADD
WASH
RINSE
SPIN
Add & Spin
ADD
WASH
RINSE
SPIN
Add & Wash
& Rinse & Spin
ADD
WASH
RINSE
SPIN
Only Wash
ADD
WASH
RINSE
SPIN
Rinse & Spin
ADD
WASH
RINSE
SPIN
ADD
HIGH
MID
LOW
POWER
WATER
LEVER
$ Pressing
the Start/
Hold Switch
# Selecting Course
WASH
RINSE
SPIN
PROCESS
START
/ HOLD
End of
Washing
It is
Informed
by buzzer.
For the reservation of finishing time
! Set your program as the
above procedure,
remaining last step.
@ Press reservation button until
the digital monitor displays the
finishing time you want.
* Press the course selection button.
* Press the procedure selection button.
* But wool/suit course can not reservation.
RES.
13
# Press Start/Hold to start.
START
/ HOLD
PERIODIC MAINTENANCE
Proper care of your washer can extend its life. This section explains how to care for your washer
properly and safely.
Cleaning your washer
Exterior
Interior
Wipe up detergent, bleach, and other spills
with a soft, damp cloth or sponge as they
occur. occasionally wipe the outside of the
washer to keep it looking like new.
Clean interior with 250ml of chlorine bleach
mixed with 500ml of detergent.
Run washer through a complete cycle.
Repeat process if necessary.
Do not put sharp or metal object in your washer,
they can damage the finish. Check all pockets
for pins, clips, money, bolts, nuts, etc.
Do not lay these objects on your washer after
emptying pockets.
Winter storage or moving care
Install and store your washer where it will not freeze. Because some water may stay in the
hoses, freezing can damage your washer.
If storing or moving your washer during freezing weather, winterize it.
To winterize washer
To use washer again
• Shut off water faucet.
• Disconnect and drain water inlet hoses
• Run washer on a drain and spin setting
(see page 13) for 1 minute.
• Unplug the power supply cord.
• Flush water pipes and hoses.
• Recombination water inlet hoses.
• Turn on water faucet.
• Recombination power supply cord.
Non-use or vacation care
Operate your washer only when you are at home.
If will be on vacation or not using your washer for an extended period of time, you should:
• Unplug the power supply cord or turn off eletrical power to the washer.
• Turn off the water supply to the washer.
This helps avoid accidental flooding (due to a water pressure surge) while you are away.
14
Cleaning the Lint Filter
! Pull the Filter frame upward.
@ Turn the lint filter inside
out, wash to the lint off
with water
# Return the filter as it was,
and insert the filter frame
into the slot
Filter Frame
Lint Filter
Cleaning the water inlet filter
• Clean the filter when water leaks from, the water inlet.
! Pull the power
plug out before
cleaning it.
@ Turn off the water
supply to the
washer and
sperate the inlet
hose.
# Pull the inlet filter
out.
$ Remove the dirt
from the inlet
filter with a brush.
Cleaning the drain filter
• In case “U” shape drain hose, this filter’s equipped at the cack side of washer.
• This drain filter is to screen the foreign stuffs such as threads, coins, pins, buttons etc ...
• If the drain filter is not cleaned at proper time (every 10 times of use), Drain problem could be
caused. see page
! Put down the remained
water in the hose. And put
a container under the filter
to collect water.
@ Turn the cap counter
clockwise.
# Pull out the filter
assembly off the case of
the main body.
FILTER
CASE
CAP
FILTER
$ Clean the drain filter
removing the foreign
stuffs.
CAP
CAP
CONTAINER
% Put in the filter along the
guiding prominence of the
case. Please note the left
position of the filter
adjusting the groove to the
CASE
guide rib.
GUIDE
RIB
FILTER
CAP
SUIT
15
^ Turn the cap clockwise
tightly.
CAP
SPECIAL GUIDES FOR REMOVING STAINS
Stained, heavily-soiled, or greasy items may need to be prewashed or soaked for best results. Soaking
helps remove protein-type stains like blood, milk, or grass. Prewashing helps loosen soil before washing.
Stain removal rules
• Use warm water for soaking or prewashing stained laundry. Hot water can set stains.
• Most stains are easier to remove when they are fresh. Old or set stains may not coconut
• Before treating any stain, find out what kind of stain it is, how old the stain is, what kind of
fabric it is, and if the fabric is colorfast. (Check the care label)
• Washing and drying can set some stains.
• Start with cold or warm water, hot water can set some stain.
• When bleach is recommended, use a bleach that is safe for the fabric.
• Put the stained area face down on a paper towel or white cloth. Apply the stain remover to
the back of the stain. This forces the stain off fabric instead of through it.
Stain removal guide
STAIN
TO REMOVE
Blood
Rinse immediately in COLD water.
If stain remains, soak in cold water with an enzyme prewash.
Chewing gum
Use ice in plastic bag to harden the gum.
Scrape off what you can and then sponge with white spirits.
Cocoa, Chocolate
Sponge with COLD water and soak in an enzyme prewash.
If stains persist, rub in a little detergent and rinse in cold water.
Coffee
Blot up quickly and rinse out in COLD water.
Rub in a little detergent and wash in the maximum temperature allowed for the
fabric type.
Cream/Milk
Ice cream
Rinse in COLD water and wash normally.
If stain is still apparent, sponge with white spirits.
Deodorant
Rub affected area with white vinegar and then rinse under running COLD water.
Sponge with white spirits.
Treat stiffened areas with enzyme prewash
Egg
Soak in a COLD enzyme prewash, rinse and wash normal.
Fabric/Softener
Rub affected area with bar soap and wash normally.
Fruit stains
Treat as soon as pressible by sponging with COLD water.
Rub a little detergent on the stain and wash normally
Grass
Sponge with white sprites.
Rub in an enzyme prewash and wash as normal
Grease and oil
Lay the affected area face down on an absorbent cloth and work from the back.
Sponge with white spirits or dry cleaning fluid. Wash normally.
Iron or rust
Apply lemon juice and salt and place in the sun. Wash normally.
Lipstick
Sponge with white methylated spirits and wash normally.
Mildew
Wash in WARM water and detergent.
Moisten area with lemon juice, dry in the sun and wash normally.
If stain persists and the fabric allows, use a bleach.
Mud
Brush off any dry mud. Rinse in cold water.
If stain persists rub in a little detergent and wash normally.
Paint-oil based
Scrape off any fresh paint and sponge with a non flammable dry cleaning fluid and
wash normally.
Paint-water based
Treat while still wet, rinse in WARM water and wash normally.
Scorch marks
Dampen a cloth with hydrogen peroxide, lay it over the affected area and press with
a fairly hot iron.
16
TROUBLE SHOOTING GUIDES
Most problems are easily solved if you understand the cause. Check the following list for problem
befor calling for service.
Before calling for service, check these
PROBLEM
CHECK POINT
• The washer will not
operate at all.
• Is there a power failure?
• Is the power cord correctly connected to an electric outlet?
• Is the electric fuse broken?
• Did you turn on the power?
• Did you press Start/Hold button?
• Is there correct amount of water in the tub?
• Water is not supplied;
• Did you connect the inlet hose and open the water tap?
• Is the inlet hose or the water tap frozen?
• Is the water supply shut off?
• Does foreign matter block up the inlet hose filter?
If water supply is not finished within 30
minutes, the lamp
will light up, and the
buzzer will sound to indicate a problem.
• The washer will not drain;
If the drain is not finished within selected
time, lamp
will light up, and the buzzer
will sound to indicate a problem.
• The washer will not spin;
If the clothes is collected on one side during
spin and the tub becomes unbalanced, the
spin operation will be interrupted, and then
this unbalanced condition will be corrected
by following operation: WATER SUPPLY →
RINSE→ DRAIN However if the
unbalanced condition is unchanged despite
repeating the above operation, the lamp
will light up, and the buzzer will sound
to indicate a problem.
• Is the drain hose frozen or blocked up by dirt?
• Is the drain hose kinked or deformed?
• Is the end of the drain hose immersed in water?
• Is there excessive dirt inside the pump housing?
• Is the clothe in the tub collected on one side?
• Is the washing machine installed on an uneven floor or is the
vibration serious?
• Is the lid open?
(The lamp
will light up in this case.)
• These cases are not malfunctions
• The sound “wing” heard during water supply is the operating sound made by the water inlet
valve.
• The sound “sha” heard in stopping the tub is the sound that comes from the autobalancer of
the tub.
• The sound “wung” heard during wash or spin is the operating sound made by the air bubble
generator.
RNOTE! R
Please check the point before calling for a service.
If the supply cord is damaged, it must only be replaced by a repair shop appointed by
manufacturer, because special purpose tools are required.
17