York THJF60 Installation manual

INSTALLATION MANUAL
R-410A OUTDOOR SPLIT-SYSTEM
HEAT PUMP
MODELS: 14.5 SEER - YHJF/THJF/THGF60
®
5 TONS – 1 PHASE
LIST OF SECTIONS
GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
UNIT INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
TXV INSTALLATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
ELECTRICAL CONNECTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
EVACUATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
SYSTEM CHARGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
SYSTEM START-UP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
INSTRUCTING THE OWNER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
WIRING DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
START UP SHEET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
LIST OF FIGURES
Typical Installation with Required Clearances . . . . . . . . . . . . . . . . . . .2
Tubing Hanger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Underground Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Heat Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Outdoor Unit Control Box - 14.5 SEER 60 Only . . . . . . . . . . . . . . . . . .5
Thermostat Wiring – Two-Stage Heat Pump Variable Speed Air Handler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Thermostat Wiring – Two-Stage Heat Pump Variable Speed Air Handler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
CFM Selection Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Heat Pump Flow Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Wiring Diagram - Single Phase - 14.5 SEER - 5 Ton . . . . . . . . . . . . 10
LIST OF TABLES
R-410A Saturation Properties . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
SECTION I: GENERAL
The outdoor units are designed to be connected to a matching indoor
coil with sweat connect lines. Sweat connect units are factory charged
with refrigerant for a matching indoor coil plus 15 feet of field supplied
lines.
Matching indoor coils are available with a thermal expansion valve or
an orifice liquid feed sized for the most common usage. The orifice size
and/or refrigerant charge may need to be changed for some indoor-outdoor unit combinations, elevation differences, or total line lengths. Refer
to Application Data covering “General Piping Recommendations and
Refrigerant Line Length” (Part Number 036-61920-001).
SECTION II: SAFETY
This is a safety alert symbol. When you see this symbol on
labels or in manuals, be alert to the potential for personal
injury.
Understand and pay particular attention to the signal words DANGER,
WARNING, or CAUTION.
DANGER indicates an imminently hazardous situation, which, if not
avoided, will result in death or serious injury.
WARNING indicates a potentially hazardous situation, which, if not
avoided, could result in death or serious injury.
Improper installation may create a condition where the operation of
the product could cause personal injury or property damage.
Improper installation, adjustment, alteration, service, or maintenance can cause injury or property damage. Refer to this manual
for assistance or for additional information, consult a qualified contractor, installer, or service agency.
This product must be installed in strict compliance with the
enclosed installation instructions and any applicable local, state,
and national codes including, but not limited to building, electrical,
and mechanical codes.
INSPECTION
As soon as a unit is received, it should be inspected for possible damage during transit. If damage is evident, the extent of the damage
should be noted on the carrier’s delivery receipt. A separate request for
inspection by the carrier’s agent should be made in writing. See Local
Distributor for more information.
CAUTION indicates a potentially hazardous situation, which, if not
avoided may result in minor or moderate injury. It is also used to
alert against unsafe practices and hazards involving only property damage.
835959-UIM-B-0413
835959-UIM-B-0413
Requirements For Installing/Servicing R-410A Equipment
•
•
•
•
•
•
•
Gauge sets, hoses, refrigerant containers, and recovery system
must be designed to handle the POE type oils, and the higher
pressures of R-410A.
Manifold sets should be 800 psig high side and 250 psig low side
with 550 psig low side restart.
All hoses must have a 700 psig service pressure rating.
Leak detectors should be designed to detect HFC refrigerant.
Recovery equipment (including refrigerant recovery containers)
must be specifically designed to handle R-410A.
Do not use an R-22 TXV.
A liquid-line filter drier is required on every unit.
The outdoor unit must have sufficient clearance for air entrance to the
condenser coil, for air discharge, and for service access. See Figure 1.
NOTE: For multiple unit installations, units must be spaced a minimum
of 18 inches apart (coil face to coil face).
If the unit is to be installed on a hot sun exposed roof or a black-topped
ground area, the unit should be raised sufficiently above the roof or
ground to avoid taking the accumulated layer of hot air into the outdoor
unit.
Provide an adequate structural support.
ADD-ON REPLACEMENT/RETROFIT
The unit should be installed in accordance with all National, State, and
Local Safety Codes and the limitations listed below:
When this unit is being used as a replacement for an R-22 unit, it is
required that the outdoor unit, indoor coil, and metering device all be
replaced. The following steps should be performed in order to insure
proper system operation and performance. Line-set change out is also
recommended.
1.
1.
LIMITATIONS
2.
3.
4.
Limitations for the indoor unit, coil, and appropriate accessories
must also be observed.
The outdoor unit must not be installed with any duct work in the air
stream. The outdoor fan is the propeller type and is not designed
to operate against any additional external static pressure.
The maximum and minimum conditions for operation must be
observed to assure a system that will give maximum performance
with minimum service.
The maximum allowable line length for this product is 75 feet.
AIR TEMPERATURE AT
OUTDOOR COIL, °F
Min.
2.
3.
•
•
AIR TEMPERATURE AT
INDOOR COIL, °F
Max.
Min.
•
Max.
DB
Cool
DB
Heat
DB
Cool
DB
Heat
WB
Cool
DB
Heat
WB
Cool
DB
Heat
50
-10
115
75
57
501
72
80
•
4.
1. Operation below this temperature is permissible for a short period of
time, during morning warm-up.
SECTION III: UNIT INSTALLATION
LOCATION
Before starting the installation, select and check the suitability of the
location for both the indoor and outdoor unit. Observe all limitations and
clearance requirements.
48” OVERHEAD
CLEARANCE
Change-out of the indoor coil to an approved R-410A coil/ condensing unit combination with the appropriate metering device.
Change-out of the line-set when replacing an R-22 unit with an
R410-A unit is highly recommended to reduce cross-contamination of oils and refrigerants.
If change-out of the line set is not practical, then the following precautions should be taken.
Inspect the line set for kinks, sharp bends, or other restrictions,
and for corrosion.
Determine if there are any low spots which might be serving as oil
traps.
Flush the line set with a commercially available flush kit to
remove as much of the existing oil and contaminants as possible.
Install a suction line filter-drier to trap any remaining contaminants, and remove after 50 hours of operation.
If the outdoor unit is being replaced due to a compressor burnout,
then installation of a 100% activated alumina suction-line filter
drier in the suction-line is required, in addition to the factory
installed liquid-line drier. Operate the system for 10 hours. Monitor
the suction drier pressure drop. If the pressure drop exceeds 3
psig, replace both the suction-line and liquid-line driers. After a
total of 10 hours run time where the suction-line pressure drop has
not exceeded 3 psig, replace the liquid line drier, and remove the
suction-line drier. Never leave a suction-line drier in the system
longer than 50 hours of run time.
MINIMUM 24” SERVICE
ACCESS CLEARANCE
ON ONE SIDE
THERMOSTAT
WEATHERPROOF
DISCONNECT
SWITCH
NEC CLASS 1 WIRING
10” CLEARANCE
AROUND PERIMETER
TO FURNACE OR
AIR HANDLER
TERMINAL BLOCK
NEC CLASS 2 WIRING
TO INDOOR COIL
NOTE:
ALL OUTDOOR WIRING
MUST BE WEATHERPROOF.
CONTROL
ACCESS
PANEL
SEAL OPENING(S) WITH
PERMAGUM OR EQUIVALENT
FIGURE 1: Typical Installation with Required Clearances
2
Johnson Controls Unitary Products
835959-UIM-B-0413
GROUND INSTALLATION
The unit may be installed at ground level on a solid base that will not
shift or settle, causing strain on the refrigerant lines and possible leaks.
Maintain the clearances shown in Figure 1 and install the unit in a level
position.
Normal operating sound levels may be objectionable if the unit is placed
directly under windows of certain rooms (bedrooms, study, etc.).
NOTE: Using a larger than specified line size could result in oil return
problems. Using too small a line will result in loss of capacity and other
problems caused by insufficient refrigerant flow. Slope horizontal vapor
lines at least 1" every 20 feet toward the outdoor unit to facilitate proper
oil return.
PRECAUTIONS DURING LINE INSTALLATION
1.
Condensate will drain from beneath the coil of the outdoor unit during
the defrost cycle. Normally this condensate may be allowed to drain
directly on the ground.
Elevate the unit sufficiently to prevent any blockage of the air entrances
by snow in areas where there will be snow accumulation. Check the
local weather bureau for the expected snow accumulation in your area.
Isolate the unit from rain gutters to avoid any possible wash out of the
foundation.
2.
3.
4.
The outdoor unit should not be installed in an area where mud or
ice could cause personal injury. Remember that condensate will
drip from the unit coil during heat and defrost cycles and that this
condensate will freeze when the temperature of the outdoor air is
below 32°F.
5.
6.
ROOF INSTALLATION
When installing units on a roof, the structure must be capable of supporting the total weight of the unit, including a pad, lintels, rails, etc.,
which should be used to minimize the transmission of sound or vibration into the conditioned space.
7.
8.
Install the lines with as few bends as possible. Care must be taken
not to damage the couplings or kink the tubing. Use clean hard
drawn copper tubing where no appreciable amount of bending
around obstruction is necessary. If soft copper must be used, care
must be taken to avoid sharp bends which may cause a restriction.
The lines should be installed so that they will not obstruct service
access to the coil, air handling system, or filter.
Care must also be taken to isolate the refrigerant lines to minimize
noise transmission from the equipment to the structure.
The vapor line must be insulated with a minimum of 1/2" foam rubber insulation (Armaflex or equivalent). Liquid lines that will be
exposed to direct sunlight and/or high temperatures must also be
insulated.
Tape and suspend the refrigerant lines as shown. DO NOT allow
tube metal-to-metal contact. See Figure 2.
Use PVC piping as a conduit for all underground installations as
shown in Figure 3. Buried lines should be kept as short as possible
to minimize the build up of liquid refrigerant in the vapor line during
long periods of shutdown.
Pack fiberglass insulation and a sealing material such as permagum around refrigerant lines where they penetrate a wall to reduce
vibration and to retain some flexibility.
See Form 690.01-AD1V for additional piping information.
UNIT PLACEMENT
Sheet Metal Hanger
1. Provide a base in the pre-determined location.
2. Remove the shipping carton and inspect for possible damage.
3. Compressor tie-down bolts should remain tightened.
4. Position the unit on the base provided.
NOTE: Heat pumps will defrost periodically resulting in water drainage.
The unit should not be located where water drainage may freeze and
create a hazardous condition - such as sidewalks and steps.
Liquid
Line
Incorrect
Tape
Correct
LIQUID LINE FILTER-DRIER
Insulated Vapor Line
The heat pumps have a solid core bi-flow filter/drier located on the liquid
line.
NOTE: Replacements for the liquid line drier must be exactly the same
as marked on the original factory drier. See Source 1 for O.E.M.
replacement driers.
FIGURE 2: Tubing Hanger
TO INDOOR COIL
LIQUID LINE
PVC
TO OUTDOOR UNIT
INSULATED
CAP
VAPOR LINE
CONDUIT
Failure to do so or using a substitute drier or a granular type may
result in damage to the equipment.
R-410A
Filter-Drier
Source 1 Part No.
Apply with Models
026-25512-000
All
13 SEER
*As listed on the “Energy Guide yellow sticker on the unit.
PIPING CONNECTIONS
The outdoor unit must be connected to the indoor coil using field supplied refrigerant grade copper tubing that is internally clean and dry.
Units should be installed only with the tubing sizes for approved system
combinations as specified in Tabular Data Sheet. The charge given is
applicable for total tubing lengths up to 15 feet. See Application Data
Part Number 036-61920-001 for installing tubing of longer lengths and
elevation differences.
Johnson Controls Unitary Products
FIGURE 3: Underground Installation
PRECAUTIONS DURING BRAZING OF LINES
All outdoor unit and evaporator coil connections are copper-to-copper
and should be brazed with a phosphorous-copper alloy material such
as Silfos-5 or equivalent. DO NOT use soft solder. The outdoor units
have reusable service valves on both the liquid and vapor connections.
The total system refrigerant charge is retained within the outdoor unit
during shipping and installation. The reusable service valves are provided to evacuate and charge per this instruction.
Serious service problems can be avoided by taking adequate precautions to assure an internally clean and dry system.
3
835959-UIM-B-0413
4.
Dry nitrogen should always be supplied through the tubing while it
is being brazed, because the temperature is high enough to cause
oxidation of the copper unless an inert atmosphere is provided. The
flow of dry nitrogen should continue until the joint has cooled.
Always use a pressure regulator and safety valve to insure that only
low pressure dry nitrogen is introduced into the tubing. Only a small
flow is necessary to displace air and prevent oxidation.
PRECAUTIONS DURING BRAZING SERVICE VALVE
Precautions should be taken to prevent heat damage to service valve
by wrapping a wet rag around it as shown in Figure 4. Also, protect all
painted surfaces, insulation, and plastic base during brazing. After brazing cool joint with wet rag.
This is not a backseating valve. The service access port has a
valve core. Opening or closing valve does not close service access
port.
If the valve stem is backed out past the chamfered retaining wall,
the O-ring can be damaged causing leakage or system pressure
could force the valve stem out of the valve body possibly causing
personal injury.
Valve can be opened by removing the plunger cap and fully inserting a
hex wrench into the stem and backing out counter-clockwise until valve
stem just touches the chamfered retaining wall.
Braze the liquid line to the evaporator liquid connection. Nitrogen
should be flowing through the evaporator coil.
5. Slide the grommet away from the vapor connection at the indoor
coil. Braze the vapor line to the evaporator vapor connection. After
the connection has cooled, slide the grommet back into original
position. Refer to the Tabular Data Sheet for proper vapor line sizing.
6. Protect the vapor valve with a wet rag and braze the vapor line
connection to the outdoor unit. The nitrogen flow should be exiting
the system from the vapor service port connection. After this connection has cooled, remove the nitrogen source from the liquid fitting service port.
7. Replace the Schrader core in the liquid and vapor valves.
8. Go to “SECTION IV” for TXV installation.
9. Leak test all refrigerant piping connections including the service
port flare caps to be sure they are leak tight. DO NOT OVERTIGHTEN (between 40 and 60 inch - lbs. maximum).
10. Evacuate the vapor line, evaporator, and the liquid line to 500
microns or less.
NOTE: Line set and indoor coil can be pressurized to 250 psig with dry
nitrogen and leak tested with a bubble type leak detector. Then release
the nitrogen charge.
NOTE: Do not use the system refrigerant in the outdoor unit to purge or
leak test.
11. Replace cap on service ports. Do not remove the flare caps from
the service ports except when necessary for servicing the system.
Connect the refrigerant lines using the following procedure:
1.
2.
3.
Remove the cap and Schrader core from both the liquid and vapor
service valve service ports at the outdoor unit. Connect low pressure nitrogen to the liquid line service port.
Braze the liquid line to the liquid valve at the outdoor unit. Be sure
to wrap the valve body with a wet rag. Allow the nitrogen to continue flowing. Refer to the Tabular Data Sheet for proper liquid line
sizing.
Carefully remove the rubber plugs from the evaporator liquid and
vapor connections at the indoor coil.
Do not connect manifold gauges unless trouble is suspected.
Approximately 3/4 ounce of refrigerant will be lost each time a standard manifold gauge is connected.
12. Release the refrigerant charge into the system. Open both the liquid and vapor valves by removing the plunger cap and with an
allen wrench back out counter-clockwise until valve stem just
touches the chamfered retaining wall. See "PRECAUTIONS DURING BRAZING SERVICE VALVE".
13. Replace plunger cap finger tight, then tighten an additional 1/12
turn (1/2 hex flat). Cap must be replaced to prevent leaks.
The evaporator is pressurized.
Never attempt to repair any brazed connections while the system is
under pressure. Personal injury could result.
See "System Charge” section for checking and recording system
charge.
SECTION IV: TXV INSTALLATIONS
For installations requiring a TXV, the following are the basic steps for
installation. For detailed instructions, refer to the Installation Instructions
accompanying the TXV kit.
Install TXV kit as follows:
1.
2.
3.
4.
FIGURE 4: Heat Protection
5.
4
First, relieve the holding charge by depressing the Schrader valve
located in the end of the liquid line.
After holding charge is completely discharged, loosen and remove
the liquid line fitting from the orifice distributor assembly. Note that
the fitting has right hand threads.
Remove the orifice from the distributor body using a small diameter wire or paper clip. Orifice is not used when the TXV assembly
is installed.
After orifice is removed, install the thermal expansion valve to the
orifice distributor assembly with supplied fittings. Hand tighten and
turn an additional 1/8 turn to seal. Do not overtighten fittings.
Reinstall the liquid line to the top of the thermal expansion valve.
Hand modify the liquid line to align with casing opening.
Johnson Controls Unitary Products
835959-UIM-B-0413
6.
7.
Install the TXV equalizer line into the vapor line as follows:
a. Select a location on the vapor line for insertion of the equalizer line which will not interfere with TXV bulb placement.
3.
4.
b.
5.
Use an awl to punch through the suction tube and insert the
awl to a depth to achieve a 1/8” diameter hole.
Install TXV equalizer line in 1/8” hole previously made in vapor
line. Equalizer line should not be bottomed out in vapor line. Insert
equalizer line at least 1/4” in the vapor line. Braze equalizer line
making sure that tube opening is not brazed closed.
Run power wiring from the disconnect switch to the unit.
Route wires from disconnect through power wiring opening provided and into the unit control box as shown in Firgure 5.
Install the proper size time-delay fuses or circuit breaker, and
make the power supply connections.
Defrost
Control
Board
Relay
Transformer
Dry nitrogen should always be supplied through the tubing while it
is being brazed, because the temperature is high enough to cause
oxidation of the copper unless an inert atmosphere is provided. The
flow of dry nitrogen should continue until the joint has cooled.
Always use a pressure regulator and safety valve to insure that only
low pressure dry nitrogen is introduced into the tubing. Only a small
flow is necessary to displace air and prevent oxidation.
Contactor
Low Voltage
Box
Snap Bushing
All connections to be brazed are copper-to-copper and should be
brazed with a phosphorous-copper alloy material such as Silfos-5 or
equivalent. DO NOT use soft solder.
Install the TXV bulb to the vapor line near the equalizer line, using the
two bulb clamps furnished with the TXV assembly. Ensure the bulb is
making maximum contact. Refer to TXV installation instruction for view
of bulb location.
Conduit
Plate
Ground Lug
Capacitor
FIGURE 5: Outdoor Unit Control Box - 14.5 SEER 60 Only
FIELD CONNECTIONS CONTROL WIRING
1.
GENERAL INFORMATION & GROUNDING
Route low voltage wiring into bottom of control box as shown in
Figure 5. Make low voltage wiring connections inside the low voltage box per Figures 6 & 7.
2. The complete connection diagram and schematic wiring label is
located on the inside surface of the unit service access panel.
3. Replace the control box cover removed in Step 2.
4. All field wiring to be in accordance with national electrical codes
(NEC) and/or local-city codes.
5. Mount the thermostat about 5 ft. above the floor, where it will be
exposed to normal room air circulation. Do not place it on an outside wall or where it is exposed to the radiant effect from exposed
glass or appliances, drafts from outside doors or supply air grilles.
6. Route the 24-volt control wiring (NEC Class 2) from the outdoor
unit to the indoor unit and thermostat.
NOTE: To eliminate erratic operation, seal the hole in the wall at the
thermostat with permagum or equivalent to prevent air drafts affecting
the operation of in the thermostat.
NOTE: A Start Assist Kit is available and recommended for long line set
applications or in areas of known low voltage problems.
Check the electrical supply to be sure that it meets the values specified
on the unit nameplate and wiring label.
DEHUMIDIFICATION CONTROL
Power wiring, control (low voltage) wiring, disconnect switches and over
current protection must be supplied by the installer. Wire size should be
sized per NEC requirements.
A dehumidification control accessory 2HU06700124 may be used with
variable speed air handlers or furnaces in high humidity areas. This
control works with the variable speed indoor unit to provide cooling at a
reduced air flow, lowering evaporator temperature and increasing latent
capacity. The humidistat in this control opens the humidistat contacts on
humidity rise. To install, refer to instructions packaged with the accessory and Figures 6 & 7. Prior to the installation of the dehumidification
control, the jumper across the HUMIDISTAT terminals on the indoor
variable speed air handler or furnace CFM selection board must be
removed.
In all cases, mount the TXV bulb after vapor line is brazed and has
had sufficient time to cool.
1.
2.
3.
Bulb should be installed on a horizontal run of the vapor line if possible. On lines under 7/8" O.D. the bulb may be installed on top of
the line. With 7/8" O.D. and over, the bulb should be installed at
the position of about 2 or 10 o'clock.
If bulb installation is made on a vertical run, the bulb should be
located at least 16 inches from any bend, and on the tubing sides
opposite the plane of the bend. The bulb should be positioned with
the bulb tail at the top, so that the bulb acts as a reservoir.
Bulb should be insulated using thermal insulation provided to protect it from the effect of the surrounding ambient temperature.
SECTION V: ELECTRICAL CONNECTIONS
All field wiring must USE COPPER CONDUCTORS ONLY and be
in accordance with Local, National, Fire, Safety & Electrical Codes.
This unit must be grounded with a separate ground wire in accordance with the above codes.
The complete connection diagram and schematic wiring label is located
on the inside surface of the unit service access panel.
FIELD CONNECTIONS POWER WIRING
1.
2.
Install the proper size weatherproof disconnect switch outdoors
and within sight of the unit.
Remove the screws from the control box cover and remove from
unit.
Johnson Controls Unitary Products
During cooling, if the relative humidity in the space is higher than the
desired set point of the dehumidification control, the variable speed
blower motor will operate at lower speed until the dehumidification control is satisfied. A 40-60% relative humidity level is recommended to
achieve optimum comfort.
If a dehumidification control is installed, it is recommended that a minimum air flow of 325 cfm/ton be supplied at all times.
5
835959-UIM-B-0413
For additional connection diagrams for all UPG equipment refer to “Low Voltage System Wiring” document available online at www.upgnet.com in the
Product Catalog Section.
HP 27A
Two Stage Heat Pump – Variable Speed Air Handler (With Hot Heat Pump Operation)
OD MODELS
ID MODELS
AV
SV
MV
THERMOSTAT
YZE
THJF060
YZH
YHJF060
H*5
H*8
CHJF060
LHJF060
GHJF060
*PP32U71124
*PP32U72124
VARIABLE SPEED
AIR HANDLER
TWO STAGE
HEAT PUMP
VARIABLE SPEED
2
AIR HANDLER CONTROL
YORKGUARD VI
CONTROL
C
24 – Volt Common
COM
24 – Volt Common
C
24 – Volt Common
Y1
First Stage Compressor
Y1
Single Stage Compressor
Y1
Single Stage Compressor
R
24 – Volt Hot
R
24 – Volt Hot
G
Fan
G
Fan
R
24 – Volt Hot
W1
First Stage Aux. Heat
W1 OUT
First Stage Heat
W2
Second Stage Aux. Heat
W2
Second Stage Aux. Heat
W2 OUT
Second Stage Heat
O
Reversing Valve
Energized in Cool
Y/Y2
Second or Full
Stage Compressor
O
Reversing Valve
Energized in Cool
L
Malfunction Light
X/L
Malfunction Light
Y2 OUT
Second Stage Compressor
O
Reversing Valve
Energized in Cool
X/L
Malfunction Light
Y2
Second Stage Compressor
Y2
Second Stage Compressor
E/W1
First Stage Aux. Heat
W
Auxiliary Heat
HUM
Humidity Switch
Open on Humidity Rise
BSG
Bonnet Sensor
24VAC Humidifier
(Optional)
HUM OUT
(24VAC out)
BS
Bonnet Sensor
24VAC
Electronic Air Cleaner
(Optional)
EAC (24VAC out)
Electronic Air Cleaner
DHM
Dehumidistat
HM
Humidistat
Step 1 of the Thermostat
Installer Table must be
set to Heat Pump
Step 2 of the Thermostat
Installer Table must be
set to 2
Step 5 of Thermostat User
Configuration Menu must
be set to “ON” for
Dehumidification
E2/P Switch must be in the
E2 position
Second stage auxiliary
heat will be controlled by
the thermostat, not the
heat pump control when
wired as shown.
Move the MODE
jumper to “HP”
Move the HUM STAT
jumper to “YES”
if humidistat is to be used.
Refer to AH documentation
for W1 and W2 electric
heat staging options.
Part Numbers:
SAP = Legacy
159481 = 031-09157
1
Change Hot Heat Pump
jumper on the heat pump
control to “ON”
2
Part Numbers:
SAP = Legacy
126768 = 031-09137
18395 = 031-01996
340512 = 031-09178
1
FIGURE 6: Thermostat Wiring – Two-Stage Heat Pump - Variable Speed Air Handler
6
Johnson Controls Unitary Products
835959-UIM-B-0413
HP 27C
Two Stage Heat Pump – Variable Speed Ai r Handler (With Hot Heat Pump Operation)
OD MODELS
ID MODELS
AV
SV
MV
THERMOSTAT
THERMOSTAT
*PP32U70124
*DN22H00124
*DP22U70124
YZE
THJF060
YZH
YHJF060
H*5
H*8
CHJF060
LHJF060
GHJF060
VARIABLE SPEED
AIR HANDLER
TWO STAGE
HEAT PUMP
VARIABLE SPEED
2
AIR HANDLER CONTROL
YORKGUARD VI
CONTROL
C
24 – Volt Common
C
24 – Volt Common
COM
24 – Volt Common
C
24 – Volt Common
Y
First Stage Compressor
Y1
First Stage Compressor
Y1
Single Stage Compressor
Y1
Single Stage Compressor
R
24 – Volt Hot
(Heat XFMR)
R
24 – Volt Hot
R
24 – Volt Hot
R
24 – Volt Hot
G
Fan
G
Fan
G
Fan
W1
First Stage Aux. Heat
W1 OUT
First Stage Heat
W2
Second Stage Aux. Heat
W2
Second Stage Aux. Heat
W2 OUT
Second Stage Heat
O/B
Reversing Valve
O
Reversing Valve
Energized in Cool
Y/Y2
Second or Full
Stage Compressor
O
Reversing Valve
Energized in Cool
L
Malfunction Light
L
Malfunction Light
X/L
Malfunction Light
E
Emergency Heat
RC
24 – Volt Hot
(Cool XFMR)
Y2 OUT
Second Stage Compressor
O
Reversing Valve
Energized in Cool
X/L
Malfunction Light
Y2
Y2
Second Stage CompressorSecond Stage Compressor
AUX
Auxiliary Heat
Y2
Second Stage Compressor
E/W1
First Stage Aux. Heat
3
External Humidistat
(Optional)
Open on Humidity Rise
Thermostat Installer Setup Step 1 of Thermostat
0170-System TypeInstaller/Configuration
must be set to 12
Menu must be set to “HP2”
Selection of GAS/ELEC
3 Heat/2 Heat Pump
Thermostat Installer Setup switch on thermostat
not necessary
0190-Changeover Valvemust be set to 0
Second stage auxiliary
O/B terminal
heat will be controlled by
Energized in Cooling
the thermostat, not the
Thermostat Installer Setup heat pump control when
wired as shown.
0200-Backup Heat Sourcemust be set to 0
Heat Pump Backup Heat
Source is Electric
1
W
Auxiliary Heat
HUM
Humidity Switch
Open on Humidity Rise
BSG
Bonnet Sensor
24VAC Humidifier
(Optional)
HUM OUT
(24VAC out)
BS
Bonnet Sensor
24VAC
Electronic Air Cleaner
(Optional)
EAC (24VAC out)
Electronic Air Cleaner
Move the MODE
jumper to “HP”
Move HUM STAT
jumper to “YES”
if humidistat is to be used.
Refer to AH documentation
for W1 and W2 electric
heat staging options.
Part Numbers:
SAP = Legacy
159481 = 031-09157
Change Hot Heat Pump
jumper on the heat pump
control to “ON”
2
Part Numbers:
SAP = Legacy
126768 = 031-09137
18395 = 031-01996
340512 = 031-09178
1
FIGURE 7: Thermostat Wiring – Two-Stage Heat Pump - Variable Speed Air Handler
Johnson Controls Unitary Products
7
835959-UIM-B-0413
CFM SELECTION BOARD SETTINGS
For proper system operation the CFM Selection Board jumpers must be
set properly.
Refer to the Tabular Data Sheet for the recommended air flow settings
for each size condensing unit.
Set the cooling speed per the instructions for the air handler or furnace
by selecting the correct COOL and ADJ taps. Verify the airflow using
the LED display on the CFM selection board.
The HEAT PUMP jumper MUST be removed for proper system operation.
The HUMIDISTAT jumper must also be removed if a dehumidistat is
installed.
The TOTAL SYSTEM CHARGE must be permanently stamped on the
unit data plate.
Total system charge is determined as follows:
1.
2.
3.
Determine outdoor unit charge from tabular data sheet.
Determine indoor coil adjustment from tabular data sheet.
Calculate the line charge using the tabular data sheet if line length
is greater than 15 feet.
4. Total system charge = item 1 + item 2 + item 3.
5. Permanently stamp the unit data plate with the total amount of
refrigerant in the system.
Use the following subcooling charging method whenever additional
refrigerant is required for the system charge. A superheat charging
method is not suitable for TXV equipped systems.
CFM SELECTION BOARD
TAP SELECTION
D
C
B
A
D
C
B
A
COOL
HEAT
ADJ
DELAY
REMOVE FOR
HEAT PUMP
HUMIDISTAT
Refrigerant charging should only be carried out by a qualified air
conditioning contractor.
Measurement Method
If a calibrated charging cylinder or accurate weighing device is available, add refrigerant accordingly.
FIGURE 8: CFM Selection Board
Compressor damage will occur if system is improperly charged. On
new system installations, charge system per tabular data sheet for
the matched coil and follow guidelines in this instruction.
SECTION VI: EVACUATION
It will be necessary to evacuate the system to 500 microns or less. If a
leak is suspected, leak test with dry nitrogen to locate the leak. Repair
the leak and test again.
To verify that the system has no leaks, simply close the valve to the vacuum pump suction to isolate the pump and hold the system under vacuum. Watch the micron gauge for a few minutes. If the micron gauge
indicates a steady and continuous rise, it’s an indication of a leak. If the
gauge shows a rise, then levels off after a few minutes and remains
fairly constant, its an indication that the system is leak free but still contains moisture and may require further evacuation if the reading is
above 500 microns.
SECTION VII: SYSTEM CHARGE
R-410A refrigerant cylinders are rose colored, and have a dip tube
which allows liquid to flow out of the cylinder in the Upright Position. Always charge the system slowly with the tank in the upright
position.
The factory charge in the outdoor unit includes enough charge for the
unit and the highest sales volume evaporator. Some indoor coil
matches may require additional charge. See tabular data sheet provided in unit literature packet for charge requirements.
Do not leave the system open to the atmosphere. Unit damage
could occur due to moisture being absorbed by the POE oil in the
system. This type of oil is highly susceptible to moisture absorption.
8
Check flare caps on service ports to be sure they are leak tight. DO
NOT OVERTIGHTEN (between 40 and 60 inch - lbs. maximum).
SECTION VIII: SYSTEM START-UP
ENERGIZE CRANKCASE HEATER
If this unit is equipped with a crankcase heater for the compressor, a
warning label with an adhesive back is supplied in the unit installation
instruction packet. This label should be attached to the field supplied
disconnect switch where it will be easily seen.
In order to energize the crankcase heater, set the indoor cooling thermostat to the OFF position. Close the line power disconnect to the unit.
An attempt to start the compressor without at least 8 hours of
crankcase heat will damage the compressor.
WITH POWER TO UNIT AND THERMOSTAT IN COOLING POSITION:
1.
In the cooling cycle, discharge gas is pumped to the outdoor coil
which is the condenser. The indoor coil is the evaporator.
2.
If fan switch is in ON position, a circuit is made through blower
relay to provide continuous blower operation.
3.
With fan switch in AUTO position, a circuit is made from thermostat cooling contact through blower relay to provide blower operation.
4.
System will cycle with thermostat demand to provide cooling as
needed.
Johnson Controls Unitary Products
835959-UIM-B-0413
TABLE 1: R-410A Saturation Properties
Temp °F
Pressure
PSIG
Temp °F
Pressure
PSIG
Temp °F
Pressure
PSIG
Temp °F
Pressure
PSIG
Temp °F
Pressure
PSIG
45
130
60
170
75
217
90
274
105
341
46
132
61
173
76
221
91
278
106
345
47
135
62
176
77
224
92
282
107
350
48
137
63
179
78
228
93
287
108
355
49
140
64
182
79
232
94
291
109
360
50
142
65
185
80
235
95
295
110
365
51
145
66
188
81
239
96
299
111
370
52
147
67
191
82
243
97
304
112
375
53
150
68
194
83
247
98
308
113
380
54
153
69
197
84
250
99
313
114
385
55
156
70
201
85
254
100
317
115
391
56
158
71
204
86
258
101
322
116
396
57
161
72
207
87
262
102
326.
117
401
58
164
73
211
88
266
103
331
118
407
59
167
74
214
89
270
104
336
119
412
CHARGE COMPENSATOR
(Empty in cooling / full in heating)
(Not included in all Units)
FIELD CONNECTED LINE
INDOOR COIL
OUTDOOR
COIL
4-WAY
REVERSING
VALVE
FILTER DRYER
(Solid core)
SUCTION
ACCUMULATOR
LIQUID
SENSOR
COMPRESSOR
BI-FLOW
TXV/CHECK
VALVE OR ORIFICE (Heating)
BI-FLOW
TXV/CHECK
VALVE (Cooling) **
FIGURE 9: Heat Pump Flow Diagram
SECTION V: INSTRUCTING THE OWNER
Assist owner with processing warranty cards and/or online registration.
Review Owners Guide and provide a copy to the owner and guidance
on proper operation and maintenance. Instruct the owner or the operator how to start, stop and adjust temperature setting.
When applicable, instruct the owner that the compressor is equipped
with a crankcase heater to prevent the migration of refrigerant to the
compressor during the OFF cycle. The heater is energized only when
the unit is not running. If the main switch is disconnected for long periods of shut down, do not attempt to start the unit until 8 hours after the
switch has been connected. This will allow sufficient time for all liquid
refrigerant to be driven out of the compressor.
2.
3.
4.
5.
The outdoor fan motor is permanently lubricated and does not
require periodic oiling.
If the coil needs to be cleaned, it should be washed with Calgon
Coilclean (mix one part Coilclean to seven parts water). Allow
solution to remain on coil for 30 minutes before rinsing with clean
water. Solution should not be permitted to come in contact with
painted surfaces.
Refer to the furnace or air handler instructions for filter and blower
motor maintenance.
The indoor coil and drain pan should be inspected and cleaned
regularly to prevent odors and assure proper drainage.
The installer should also instruct the owner on proper operation and
maintenance of all other system components.
MAINTENANCE
1.
Dirt should not be allowed to accumulate on the outdoor coils or
other parts in the air circuit. Clean as often as necessary to keep
the unit clean. Use a brush, vacuum cleaner attachment, or other
suitable means.
Johnson Controls Unitary Products
IT IS UNLAWFUL TO KNOWINGLY VENT, RELEASE OR DISCHARGE REFRIGERANT INTO THE OPEN AIR DURING
REPAIR, SERVICE, MAINTENANCE OR THE FINAL DISPOSAL
OF THIS UNIT.
SUBCOOLING CHARGE TABLE IS ON THE UNIT RATING
PLATE.
9
835959-UIM-B-0413
SECTION VI: WIRING DIAGRAM
FIGURE 10: Wiring Diagram - Single Phase - 14.5 SEER - 5 Ton
10
Johnson Controls Unitary Products
835959-UIM-B-0413
NOTES
Johnson Controls Unitary Products
11
835959-UIM-B-0413
SECTION VII: START UP SHEET
Heat Pump and Supplementary Heat Start-Up Sheet
Print Form
Reset Form
Proper start-up is critical to customer comfort and equipment longevity
Start-Up Date
Technician Performing Start-Up
Installing Contractor Name
Owner Information
Name
Address
City
State or Province
Equipment Data
Upflow
Zip or Postal Code
Downflow
Horizontal Left
Indoor Unit Model #
Indoor Unit Serial #
Indoor Coil Model #
Indoor Coil Serial #
Outdoor Unit Model #
Outdoor Unit Serial #
Horizontal Right
Filter, Thermostat, Accessories
Filter Type
Filter Size
Filter Location(s)
Thermostat Type
Other System Equipment and Accessories
Connections -- Per Installation Instructions and Local Codes
Unit is level
Supply plenum and return ducts are connected and sealed
Refrigerant piping complete and leak tested
Gas piping is connected (if applicable)
Vent system is connected (if applicable)
Condensate drain for indoor coil properly connected
Condensate drain for furnace (if applicable)
Electrical: Line Voltage
Indoor unit (volts AC)
Outdoor unit (volts AC)
Ground wire is connected
Overcurrent Protection Breaker / Fuses Amperes
Polarity is correct (120vac indoor units) black is L1 (hot), white is N (neutral)
Electrical: Low Voltage
Thermostat wiring complete
Heat anticipator is set to the recommended value listed in the Installation Instructions
Low voltage values: "R" and "C" at Indoor unit control board (volts AC)
Heat anticipator
recommended value
"R" and "C" Outdoor unit control board (volts AC)
Supplementary Heating Set-Up
Heating Type
Electric Air Handler
Inlet Gas Pressure (in. w.c.")
Natural Gas
Manifold Gas Pressure (in. w.c.")
Calculated input in btuh - clock the gas meter (Nat Gas Only)
Electric Heat Kit Part # (if applicable)
Venting (if applicable)
KW installed
LP Gas (Requires LP Conversion Kit)
LP Gas Conversion Kit Part # Used
LP Kit Installed By
Rated BTU/H (furnaces)
Venting system properly sized, within the limitations of the charts in the installation instructions.
Intake Size
# of 90 Degree Ells
# 0f 45 Degree Ells
Length
Exhaust Size
# of 90 Degree Ells
# 0f 45 Degree Ells
Length
Continued on next Page
12
Johnson Controls Unitary Products
835959-UIM-B-0413
Air Side: System Total External Static Pressure
Supply static before indoor coil (in w.c.")
Supply static after indoor coil (in w.c.")
Return Static (in w.c.") before filter
Return Static (in w.c.") after filter (furnace side)
Total External Static Pressure
Maximum Rated ESP (in w.c.")
COOL
Cooling
&
Heat Pump
Indoor
Blower Set-Up
ADJUST
ECM
DELAY
Return Air: Dry Bulb
A
B
C
D
A
B
C
D
A
B
C
D
X-13
1
2
3
4
5
PSC
Low
Medium Low
Medium
Medium High
High
Wet Bulb
Supply Air: Dry Bulb
ECM
Supplementary
Heating
Indoor
Blower Set-Up
HEAT
X-13
1
PSC
Low
Return Air: Dry Bulb
Temperature Drop
Outside Air: Dry Bulb
A
B
C
D
2
3
4
5
Medium
Low
Wet Bulb
Medium
High
Medium
Supply Air: Dry Bulb
High
Temperature Rise
Defrost Control Board
Fill in the information ie.. "ON", "OFF" or the appropriate "Value" for the fields that apply to the defrost control board installed
YorkGuard VI
Low Temp Cut Out
Hot Heat Pump
Demand Defrost
Time and Temperature Part Number
Balance Point
Defrost Curve
Bonnet Sensor Present
Orifice Size
TXV #
R-410A
TXV
Fixed Orifice
Liquid Line Temp
FFUEL
Switch Point
Run Time: Time and Temperature board only 30, 60 or 90 minutes
Refrigerant Charge and Metering Device
R-22
Y2 Lock
Version Number
Additional Lineset Length
# Elbows
High Side Pressure
Adder per foot - lbs.
Oz.
Total Added - lbs.
Oz.
# 45s
Suction Line Temp
Subcooling
Low Side Pressure
Superheat
Cycle Test
Operate the unit through several heating cycles from the thermostat, noting and correcting any problems
Operate the unit through continuous fan cycles from the thermostat, noting and correcting any problems
Operate the unit through a cooling cycles, noting and correcting any problems
Operate the unit through an emergency heating cycles, noting and correcting any problems
Clean Up
Installation debris disposed of and indoor and outdoor areas cleaned up?
Continued on next Page
Johnson Controls Unitary Products
13
Owner Education
Provide owner with the owner's manual
Explain operation of system to equipment owner
Explain thermostat use and programming (if applicable) to owner
Explain the importance of regular filter replacement and equipment maintenance
Comments Section
Subject to change without notice. Published in U.S.A.
Copyright © 2013 by Johnson Controls, Inc. All rights reserved.
York International Corp.
5005 York Drive
Norman, OK 73069
835959-UIM-B-0413
Supersedes: 835959-UIM-A-0112