ProShop LED Diamond Beam 5 User manual

LED Diamond Beam 5
User Manual
LED Diamond Beam 5
5 x 7 watt LEDS
www.showtech.com.au
1
LED Diamond Beam 5
Table of Contents
1. Safety instructions…………………………………………………………3
1.1 Overhead rigging …………………………………………………….4
1.2 Power Connection …………………………………………………..6
1.3 Cleaning and Maintenance ……………………………………..6
2. Menu Navigation ............................................................7
3. DMX Allocation ..............................................................10
4. Technical Specifications ..................................................11
2
LED Diamond Beam 5
1. Safety Instructions
FOR SAFE AND EFFICIENT OPERATION
Be careful with heat and extreme temperature.
Avoid exposing it to direct rays of sun near a heating appliance.
Do not put it in a temperature below 41°F/5°C, or exceeding 95°F/35°C.
Keep away from humidity, water and dust.
Do not place the set in a location with a high humidity or lots of dust.
Containers with water should not be placed on the set.
Keep away from sources of hum and noise
Such as transformer motor, tuner, TV set and amplifier.
To avoid placing on un-stable location
Select a level and stable location to avoid vibration.
Do not use chemicals or volatile liquids for cleaning
Use a dry cloth to wipe off the dust, or a wet soft cloth for stubborn dirt.
NO USER SERVICABLE PARTS INSIDE.
If unit is out of service please contact your point of purchase.
If any troubles arise, remove the power plug and contact your Pro Shop
representative for repair. Do not open the cabinet by yourself, it might result a
danger of electric shock.
Take care with the power cable. Never pull the power cable to remove the plug from
the receptacle, be sure to hold the plug.
3
LED Diamond Beam 5
When not using the unit for an extended period of time be sure to disconnect the
plug form the receptacle.
1.1 . Overhead Rigging
This item must be built in a way that it can hold 10 times more of its weight for 1
hour without causing any damages. The installation must be secured with a
secondary safety attachment. The Safety attachment has to be constructed in a way
that no part of the installation can fall down. When rigging, de-rigging or servicing
the fixture staying in the area below the installation place, on bridges, under high
working places and other endangered areas us forbidden. Before taking the device in
operation, the installation must be approved by an expert. The operator has to make
sure that safety-relating and machine-technical installations are approved by a skilled
person once a year.
IMPORTANT! OVERHEAD RIGGING REQUIRES EXTENSIVE EXPERIENCE.
Including (but not limited to) calculating working load limits, installation material
being used, and periodic safety inspection of all installation material and the
projector. If you lack these qualifications, do not attempt the installations yourself,
but instead use a professional structural rigger. Improper installation can result in
bodily injury and/or damage to property.
Use only professional trussing system if the item shall be lowered from the ceiling or
high joists. Never let the device swing freely in a room.
CAUTION: Overhead Items may cause serious injuries when crashing down!! If there
is concern about the safety then DO NOT INSTALL the device.
4
LED Diamond Beam 5
DANGER OF FIRE!
When installing the device, make sure there is no highly-flammable material
(decoration articles, etc) within a distance of min. 0.5m.
Mount the projector with the mounting bracket to your trussing system using an
appropriate clamp.
For overhead use, always install a safety-rope that can hold at least 10 times the
weight of the fixture. You must only use safety –ropes with quick links with screw
cap. Pull the safety-rope through the hole in the mounting bracket and over the
trussing system or a safe fixation spot. Insert the end in the quick link and tighten the
safety screw. The maximum drop distance must never exceed 20cm
A safety rope which already held the strain of a crash or which is defective must not
be used again.
DANGER TO LIFE!
Before taking into operation for the first time, the installation has to be approved by
an expert.
5
LED Diamond Beam 5
1.2. Power Connection
!! CAUTION !!
Never leave this device running unattended!! Every person that is involved with this
item has to be qualified!!
Connect item with main plug. The voltage and frequency must exactly be the same as
stated on the device. The power plug must always be inserted without force.
1.3. Cleaning and Maintenance
Please make sure that safety-relating and machine-technical installations are
inspected by a skilled person once a year.
1.
2.
3.
Make sure before installing that all screws are tightly connected and not corroded.
There must be no deformations on the housings, fixations and installations spots
No damages must be showed on the power supply cables, material fatigue and
sediments
If the exterior of the unit is going to be cleaned, please use moist, lint free cloths.
Never use alcohol or solvents.
The Cooling fan must be cleaned monthly and check to ensure it is free of
obstructions.
To clean the interior of the device please use a vacuum cleaner or an air jet, however
we recommend cleaning the lenses weekly to ensure the best output from your unit.
6
LED Diamond Beam 5
2.0 Menu navigation
Menu Selection
Options
Auto Show
Auto Show 1
Extended Options
Auto Show Speed 0-100, slowfast
Allows the user to select in
built auto show
Auto Show 2
Auto Show 3
Auto Show 4
Auto Show 5
Auto Show 6
Auto Show 7
Auto Show 8
Auto Show 9
Auto Show 10
Auto Show 11
Auto Show 12
Sound
Auto Show 1
Allows the user to select a
inbuilt sound activated show
Auto Show 2
Auto Show 3
Auto Show 4
Auto Show 5
Auto Show 6
7
LED Diamond Beam 5
Auto Show 7
Auto Show 8
Auto Show 9
Auto Show 10
Auto Show 11
Auto Show 12
Dimmer Mode
Allows the user to select
from 4 options of dimming
speeds
Off
Dimmer Speed off
Dimmer 1
Dimmer Speed Fast
Dimmer 2
Dimmer Speed Medium
Dimmer 3
Dimmer Speed Slow
Back Lite
On
LCD Backlight will remain on
Adjusts the setting of the
LCD back light
10s
LCD off after 10 seconds
20s
LCD off after 20 seconds
30s
LCD off after 30 seconds
Test
Auto Test
Info
Fixture Hours
test function and hour log
Version
DMX Address
DMX Address
Set the unit start address
8
Fixture running time
Versiosn number
001-512
LED Diamond Beam 5
DMX Channel
4 Channel Mode
1 pixel + shutter + macros/speed
Adjust the DMX mode
on the unit
5 Channel Mode
5 pixels
Master / Slave
Master
Master Mode
Allows the unit to be set in
slave mode to copy other
units on DMX chain
Slave
Slave Mode
9
LED Diamond Beam 5
3.0 DMX Allocation
4ch
5ch
1
All
Pixels
2
Shutter
000-255
000-010 No Function
011-255 Strobe Slow to Fast
000-010 No Function
011-030 Chase 1
031-050 Chase 2
051-070 Chase 3
071-090 Chase 4
091-110 Chase 5
3
Chase
111-130 Chase 6
131-150 Chase 7
151-170 Chase 8
171-190 Chase 9
191-210 Chase 10
211-230 Chase 11
231-250 Chase 12
251-255 Sound
4
Speed
000-255 Speed Slow to Fast
1
Pixel 1
000-255
2
Pixel 2
000-255
3
Pixel 3
000-255
4
Pixel 4
000-255
5
Pixel 5
000-255
10
LED Diamond Beam 5
4.0 Technical Specifications
Power in: 100-240 VAC, 50/60Hz
Power consumption: 45 W
LED type: Cree 7W Cool White
Number of LEDs: 5 pcs
Beam angle: 125°
Dimensions (L x W x H): 500 x 98 x 217 mm
Weight: 3.2 kg
11