Miele KM 87-2 Operating instructions

Operating instructions
Ceramic hobs
KM 84-2, KM 87-2
KM 94-2, KM 97-2
@Q\ä}
M.-Nr. 03 998 291
Contents
Contents
Help to protect our environment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Description of the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Warning and Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Before using for the first time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Hob controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Cooking areas - Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Cooking areas - Use. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Cleaning and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Correcting minor faults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
After Sales Service. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Electrical connection and technical data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Appliance dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Instructions for building-in . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Help to protect our environment
Help to protect our environment
Disposal of packaging
The transport and protective packing is
mostly manufactured from the following
re-usable materials:
. . . Corrugated paper / card - mostly
from recycled materials.
. . . Polyethylene foil (PE) partly from secondary raw materials.
Disposal of your old machine
Old machines contain materials which
can be recycled. Please contact your
local authorities or scrap merchant
about potential recycling schemes,
before disposing of the appliance.
Read the notes on page 7 before disposing of the appliance.
Rather than just throwing these materials away, please take them to the
nearest local authority collection point
for specific waste.
3
Description of the appliance
Description of the appliance
KM 84-2 / KM 87-2
3
4
2
1
5
7
8
7
6
KM 94-2 / KM 97-2
3
4
2
5
1
8
12 8 11
6
10 8
9
8 7
Description of the appliance
Description of the appliance
KM 84-2 / KM 87-2
b Control panel
c Cooking area - Ø 14.5 cm
d Cooking area - Ø 18 cm
KM 87-2: Halogen
e Residual heat indicator
f Connection cable with plug,
approx. 1.10 m long.
N.B. Plug according to country.
g Control for the front cooking area
h Cooking area indicator lights
i Control for the rear cooking area
KM 94-2 / KM 97-2
b Control panel
c Cooking area - Ø 18 cm
KM 97-2: Halogen
d Cooking area - Ø 14.5 cm
e Cooking area - Ø 14.5 cm
Data plate
Because the data plate is no longer
visible once the appliance has been
built in a 2nd data plate is supplied
which should be stuck into the space
provided on page 15 of these instructions under After Sales Service.
Special accessories
Special accessories are available from
your Miele Dealer or from the Spare
Parts Department.
Stainless steel cover EA 80
A stainless steel cover is available for
the KM 84-2 / KM 87-2 ceramic hobs.
Check availability in each country. For
installation of the cover a minimum distance of 510 mm (or respective distance for cooker hood in installation instructions) is required between the
worktop and wall units.
KM 97-2: Halogen
f Cooking area - Ø 18 cm
g Connection cable,
approx. 1.30 m long
h Control for the front right cooking
area
i Cooking area indicator lights
j Control for the rear right cooking area
k Residual heat indicators
l Control for the rear left cooking area
m Control for the front left cooking area
5
Warning and Safety Instructions
Warning and Safety Instructions
This appliance complies with all relevant legal safety requirements. Improper use of the appliance can,
however, present a risk of both personal injury and material damage.
Before installation and before using
the appliance for the first time read
the operating instructions carefully.
They give information on safety, on
the operation and care of the appliance. This way you will avoid the
risk of accidents and damage to the
appliance.
The appliance is intended for domestic use.
Should it be installed for commercial
use the relevant regulations must be observed.
For safety reasons, this appliance
may only be operated as a built-in
appliance. This is necessary to ensure
that all electric components are
shielded.
The electrical safety of the appliance can only be guaranteed
when continuity is complete between
the appliance and an effective earthing
system which complies with local and
national regulations. It is most important that this basic safety requirement is
regulary tested by a qualified electrician. The manufacturer can not be held
responsible for the consequences of an
inadequate earthing system.
6
Installation work and repairs may only
be carried out by suitably qualified and
competent persons to ensure safety.
Repairs and other work by unqualified
persons could be dangerous.
Do not connect the appliance to
the mains electricity supply by an
extension lead. Extension leads do not
guarantee the required safety of the appliance.
Please ensure that the domestic
supply corresponds to the information on the machine’s data plate.
The appliance is only completely
isolated from the electricity supply
when it is switched off at the wall
socket, or the mains fuse is withdrawn.
Do not pull by the mains cable, but by
the plug when withdrawing the plug
from the socket.
The distance between the hob and
a cooker hood should be at least:
55 cm for electric hobs.
Australia: 60 cm!
To avoid the danger of fire do not
flambe under a cooker hood.
Do not let small children touch the
appliance during operation. Not
only do the cooking areas of the ceramic hob heat up, but also the control
panel. Danger of burning. Keep all
pans out of the reach of children.
Supervise use of the hob by the elderly
or infirm.
Warning and Safety Instructions
Warning and Safety Instructions
Do not leave the appliance unattended when cooking with oils and
fats as these are fire hazards if overheated.
When switched on, the cooking
areas heat up extremely quickly.
The residual heat indicators will show
whether a cooking area is switched on,
or is still hot.
Always ensure that food is sufficiently cooked or reheated.
Many factors will affect the overall cooking time, including the size and amount
of food, its temperature, changes to the
recipe and the shape and size of cooking container.
Some foods may contain micro organisms which are only destroyed by
thorough cooking, therefore when cooking or reheating foods, e.g. poultry, it is
par-ticulary important that the food is
fully cooked through. If in doubt select
a longer cooking or reheating time.
It is essential to ensure that food
has been evenly and sufficiently
heated, and to check that it is thoroughly cooked, turning or stirring during cooking if necessary.
When using kitchen appliances
connected to sockets near the ceramic hob ensure that the cable cannot
touch a heated hob or pan.
Do not use the control panel as a
resting place for pots and pans.
Do not use the ceramic hob to
heat up the room.
The high temperatures of the hob could
cause inflammable objects in the vicinity to burn.
Only for Halogen hobs
Do not stare at halogen cooking
areas when heating if there is no pan in
place.
This could cause damage to the eyes.
Do not use the hob as a resting
place for anything else. This could
lead to a danger of the article catching
fire, if the hob were to be switched on
inadvertently.
Do not use plastic or aluminium foil
containers.
These melt at higher temperatures and
could damage the ceramic surface.
In the event of any breakages or
cracks occuring in the ceramic
hob it must be switched off immediately
and disconnected from the electricity
supply.
Contact the Miele Service Department.
Do not use the hob until the damaged
ceramic plate has been replaced. Continued use would be dangerous as
liquids etc. boiling over could penetrate
the electrical components through the
crack.
7
Warning and Safety Instructions
Warning and Safety Instructions
Do not allow either solid or liquid
sugar or pieces of plastic or aluminium foil to get onto the ceramic hob
when it is hot.
If this should occur do not switch the
appliance off. Scrape all the sugar,
plastic, or aluminium remains from the
hob with a sharp blade taking care not
to burn yourself.
If this is allowed to cool before the hob
has been cleaned, the ceramic surface
will be susceptible to pitting or even
cracking.
Do not use any pots or pans on the
ceramic hob with bases with pronounced edges or ridges.
These could scratch or scour the hob
surface permanently.
Do not push enamelled pots or
pans such as chip pans across the
ceramic hob as this can cause scratches to occur.
Do not drop anything on the ceramic hob.
Dropping a salt cellar, for example,
could be the cause of damage in certain circumstances.
If no wooden protective board (see
p. 19) is fitted between the hob
and a drawer underneath, spray canisters or inflammable substances must
not be stored in the drawer. Any cutlery trays must be made of a heat resistant material.
8
Under no circumstances use a
steam-cleaning appliance to clean
the ceramic hob. The steam could
penetrate to live components and
cause a short circuit.
In countries which may be subject
to infestation by cockroaches or
other vermin, pay particular attention to
keeping the appliance and its surroundings in a clean condition at all times.
Any damage which might be caused
by cockroaches or other vermin will not
be covered by the appliance guarantee.
Keep these instructions in a safe
place and pass them on to any future
user.
Disposal of discarded appliances
Before disposal of an old appliance, turn off at the mains, disconnect and remove the appliance
cable at both ends and render useless.
This is intended to prevent the discarded appliance from being a hazard.
The manufacturer cannot be held
liable for damage caused by noncompliance with safety instructions.
Before using for the first time
Before using for the first time
Read the ”Warning and Safety instructions“ before using for the first
time.
Thoroughly clean the ceramic hob before use and then clean regularly after
use when just warm to the touch or
cold (see ”Cleaning and care“).
There might be a slight smell on first
use due to drying effect of the insulation material.
9
Hob controls
Hob controls
All cooking areas are controlled by
variable energy regulators. By using
these energy regulators, the temperature can be freely selected.
The controls can be turned either clockwise or anti-clockwise.
The indicator light for each cooking
area comes on as soon as the respective energy regulator is turned to a setting.
It goes out when the energy regulator is
turned to the ”0“ position.
A resistance is felt between settings 7
and 8 to indicate that a higher temperature range is being reached.
10
Correct procedure:
Place saucepan of food on cooking
area.
Select a high number for boiling or
sealing in juices.
Should a trace of steam become
visible on the edge of the lid, switch
to a lower number for continued
cooking.
Turning the temperature down at the
right time . . .
. . . prevents food from overcooking.
. . . prevents food from burning.
. . . saves energy.
Hob controls
Table of settings for energy regulators
Setting
Melting butter, chocolate etc.
Dissolving gelatine
Preparing yoghurt
1-2
Keeping food warm
Warming small quantities of food / liquid
Thickening sauces containing egg yolk and butter
Cooking milk pudding
Omelettes
1-3
Defrosting deep frozen food
Cooking rice, pasta, porridge
Steaming fruit, vegetables, fish
Cooking broths, pulse soups
Braising meat, fish, vegetables
Cooking dumplings, potatoes, soups
Preparing jams, jellies, stewed fruit
Frying chops, liver, sausage, fish, eggs
3-5
4-6
7 - 10
Frying pancakes, dropped scones and other liquid batters
Frying steaks
9 - 12
Deep frying (chips, fritters)
Boiling water
These figures, which envisage approx. 4 helpings, should only be taken as a guide. With deep pans,
large quantities, or without the lid on a higher setting is needed. With smaller quantities select a lower
setting.
11
Cooking areas - Description
Cooking areas - Description
Cooking areas - diameter
The cooking areas are clearly marked
on the hob unit. Only the particular
area which has been switched on will
be heated. The rest of the hob surface
remains relatively cool.
Residual heat indicator
Each cooking area has a residual heat
indicator. When a cooking area is
switched on its residual heat indicator
lights up. It only goes out after the cooking area has been switched off and this
area of the ceramic surface has
reached a temperature safe to the
touch.
Temperature limiter
All cooking areas are fitted with a temperature limiter, which switches the
heating element off if the temperature
under the ceramic surface is too high.
The temperature limiter switches the
heating element on again after the temperature has returned to a safe level for
the ceramic material.
The temperature limiter mainly reacts
. . . when unsuitable cooking utensils
are used e.g. saucepans with uneven
bases or which are too small.
. . . when cooking areas are used without a saucepan.
12
The temperature limiter can also be
activated . . .
. . . even when the utensils are suitable.
The reason for this could be light coloured saucepan bases (heat reflection), bad transfer of heat from saucepan base to foodstuff (saucepans with
bases which store heat) etc.
Important note
Whilst the ceramic cooking areas are
heating up, a ”humming“ noise may
be noticed. This is caused by magnetization of the heating filaments. As the
cooking areas heat up, the humming
noise diminishes and finally ceases
altogether.
For halogen cooking areas only:
The radiant elements work together
with the halogen lamps. This gives a
quicker heat transfer to the pan base,
resulting in a shorter heating-up period.
Cooking areas - Use
Cooking areas - Use
Saucepans
Saucepan size
The following notes are designed to
enable you to
. . . make the best use of energy when
using your ceramic hob.
. . . prevent food boiling over and burning on to the ceramic hob.
Saucepans are available which have
been specially tested for use on a
glass ceramic hob unit.
The diameter of the saucepan should
be a little larger than that of the cooking
area.
Saucepan lids
Saucepan bases
So that optimum energy consumption
is achieved during cooking, only saucepans with bases as flat as possible, or
very slightly concave, should be used.
When the saucepan is hot, the base
should rest evenly on the ceramic surface.
A lid on the saucepan will prevent heat
from being lost.
Only use saucepans approved for
use on ceramic hobs. Do not use
pots or pans on the ceramic hob
with bases with pronounced edges
or ridges.
These could scratch or scour the
hob surface permanently.
13
Cooking areas - Use
Cooking areas - Use
Note:
Do not use any pots or pans on the
ceramic hobs with bases with pronounced edges or ridges. These
could scratch or scour the hob surface permanently.
Place a saucepan on the cooking
area before switching on the appliance to save energy.
The ceramic surface and the base of
the saucepan should be clean and
dry.
This saves unnecessary cleaning
after cooking and protects the cooking area.
Care should be taken that no sandlike grains are on the hob when cooking is to begin.
If such grains should find their way
under the saucepan when it is
pushed across the hob, the grains
could cause scratches on the surface.
Do not push enamelled baking
sheets, frying pans and saucepans
to and fro across the ceramic surface.
Otherwise scratches may occur.
14
When using aluminium or stainless
steel utensils, the metal can affect
the ceramic surface by leaving
mother-of-pearl coloured flecks behind.
These marks can be removed most
easily if they are treated immediately
they appear with a special proprietary cleaning agent (see chapter
”Cleaning and Care“).
Do not allow either solid or liquid
sugar or pieces of plastic or aluminium foil to get onto the ceramic hob
unit when it is hot.
If this should occur do not switch the
appliance off. Scrape all the sugar,
plastic or aluminium remains from
the hob with a sharp blade taking
care not to burn yourself.
If this is allowed to cool before the hob
has been cleaned, the ceramic surface will be susceptible to pitting or
even cracking.
Cleaning and care
Cleaning and care
Ceramic hob
Basically you can use the same cleaning agents for the ceramic hob as you
would for ordinary glass surfaces.
Never use scouring agents or pads,
or strong cleaners such as oven
sprays or stain removers, as these
could harm the surface.
Clean after each use
Wipe off any minor spills with just a
damp cloth.
If the hob is cleaned with a proprietary
cleaner, for example washing up liquid,
light blue staining might occur. These
stains can be removed with one of the
proprietary agents mentioned, although
they can be stubborn, and may take
several applications.
Hardened spills should be carefully
scraped off with a sharp blade. The
hob surface should then be rubbed
clean with a damp cloth.
Light marks with a metallic sheen
(Aluminium deposits) on the hob surface can be removed once the hob has
cooled down by using a suitable proprietary cleaner.
Lime deposits on the ceramic surface,
caused for example by water boiling
over, can be removed with vinegar or a
proprietary ceramic hob cleaner.
Removal of sugar, or syrups, plastic
or aluminium foil
On no account turn off the cooking
area affected.
Scrape off the sugar or other
residue thoroughly from the hot hob
with a sharp blade taking care not
to burn yourself. Then switch off the
hob, and when it is cool, clean with
a recommended cleaner.
Suitable proprietary cleaners
There are proprietary cleaners on the
market for ceramic hobs. Follow the
manufacturer’s instructions.
Do not apply to the hob when still
hot.
After applying the proprietary cleaning
agent let it dry and then rub it off using
paper kitchen towels.
Always make sure that every trace of
cleaning agent has been removed, as it
could have an adverse effect on the
hob when heated up. Remove using a
damp cloth.
Some cleaners incorporate a silicone
agent which acts as a protective film on
the ceramic hob.
It makes the hob surface smoother and
prevents water and soiling adhering to
the surface.
However, cooking at high temperatures
reduces the effect and the cleaner
needs to be reapplied for renewed
effect.
15
Cleaning and care
Cleaning and care
By always cleaning your ceramic hob
with one of these cleaning agents you
will help to avoid the damage caused
by sugar and syrups and aluminium foil
deposits.
Facia panel / Control knobs
Do not use any scouring agents or
pads on the knobs or facia, as
these could cause damage.
Clean the hob controls and the facia
panel with hot water and a little washing up liquid.
After application rub dry with a clean
cloth.
16
Correcting minor faults
Correcting minor faults
Repairs to electrical appliances
should only ever be carried out by a
competent person. Unauthorised
repairs can be dangerous.
Some minor problems, however, can
be dealt with as follows:
What to do if . . .
. . . a humming sound is heard while
the ceramic hob is heating up?
This is not a fault. As the cooking
areas heat up, the humming disappears completely.
. . . a resistance is felt between settings 7 and 8?
This is not a fault. The resistance is
there to indicate that a higher temperature range is being reached.
. . . the cooking area does not get hot
when switched on and the cooking
area indicator light does not come
on?
Check that the mains fuse is in order.
If it is call the Customer Service
Department for assistance.
17
After Sales Service
After Sales Service
In the event of any fault which you cannot correct yourself, or if the appliance
is under guarantee, please contact
Your Miele Dealer
or
The Miele Service Department
The address of the nearest Service
Department is given on the back page.
When contacting the Service Department, please quote the Model and
Serial No. of the appliance, both of
which can be found on the data plate.
Space for data plate supplied
18
Electrical connection and technical data
Electrical connection and technical data
Electrical connection
General notes
Electrical connection of the appliance
should be undertaken by a qualified
electrician in strict accordance with
national and local safety regulations.
For extra safety it is advisable to install
a residual current device (RCD), with a
trip current of 30 mA.
The Technical data table (next page)
gives details for each appliance.
The data plate gives the necessary
data for connection. See page 15.
Electrical connection U.K., AUS
(IRL, NZ, ZA)
The appliances are supplied with a
mains cable for connection to an a.c.
single phase 240 V (230 V), 50 Hz supply. The fuse rating and rated load are
given on the data plate.
For the KM 84-2 / KM 87-2 combiset
units connection should be made via a
fused plug (U.K. only) and switched
socket. The On-Off switch should be
easily accessible after the appliance
has been built in.
For the KM 94-2 / KM 97-2 combiset
units connection should be made via a
suitable isolator which complies with national and local safety regulations.
Important:
The wires in the mains lead are coloured in accordance with the following
code:
Green/yellow = earth
Blue = neutral
Brown = live
As the colours of the wires in the mains
lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:
The wire which is coloured green and
yellow must be connected to the terminal in the plug which is marked with the
letter E or by the earth symbol z or coloured green or green and yellow.
The wire which is coloured blue must
be connected to the terminal which is
marked with the letter N or coloured
black.
For U.K.: The wire which is coloured
brown must be connected to the terminal which is marked with the letter L or
coloured red.
For Australia: The wire which is coloured brown must be connected to the
terminal which is marked with the letter
A or coloured red.
WARNING
THIS APPLIANCE MUST BE
EARTHED
19
Electrical connection and technical data
Electrical connection and technical data
Non-rewireable plugs BS 1363 (U.K.)
If this machine or appliance is fitted
with a non-rewireable plug, the following information applies:
If the socket outlets are not suitable for
the plug supplied with this product, it
must be cut off and an appropriate
plug fitted.
The plug cut from the flexible cord
should be disposed of and on no account be inserted into a 13 A socket
elsewhere in the house (electric shock
hazard).
The fuse cover must be re-fitted when
changing the fuse, and if the fuse
cover is lost, the plug must not be used
until a suitable replacement is obtained. The colour of the correct replacement cover is that of the coloured
insert in the base of the plug, or the colour that is embossed in words in the
base of the plug (as applicable to the
design of plug fitted).
The correct fuse rating of the replacement fuses that are ASTA approved to
BS 1362 should be fitted. Replacement
fuse covers may be purchased from
your local electrical suppliers, electricity showrooms, or Miele Service
Agent.
Technical data
Total connected load
– U.K.
– IRL, ZA
– AUS
– NZ
Electrical connection
– U.K.
– IRL, ZA
– AUS
– NZ
Fuse rating
– U.K., IRL, ZA
– AUS, NZ
Plug rating AUS, NZ
Connection cable
Core cable, 4-core
KM 84-2
KM 87-2
KM 94-2
KM 97-2
2900 W
2660 W
2900 W
2660 W
3100 W
2900 W
n/a
n/a
5800 W
5320 W
5800 W
5320 W
5800 W
5760 W
n/a
n/a
~ 50 Hz
~ 50 Hz
~ 50 Hz
~ 50 Hz
240 V
230 V
240 V
230 V
~ 50 Hz 240 V
~ 50 Hz 230 V
n/a
n/a
13 A
13 A
15 A
1.10 m
1.10 m
The KM 84-2 and KM 87-2 need a 3 x 1.5 mm2 core cable,
should the connection cable ever need to be replaced.
The KM 94-2 and KM 97-2 need a 3 x 2.5 mm2 core cable,
should the connection cable ever need to be replaced.
20
~ 50 Hz
~ 50 Hz
~ 50 Hz
~ 50 Hz
240 V
230 V
240 V
230 V
~ 50 Hz 240 V
~ 50 Hz 230 V
n/a
n/a
30 A
20 A
30 A
1.30 m
1.30 m
Appliance dimensions
Appliance dimensions
KM 84-2, KM 87-2
KM 94-2, KM 97-2
21
Instructions for building-in
Instructions for building-in
These hobs are classified as ”Y“ class
for heat protection. There may be a
wall at the rear and wall or tall units at
one side. On the other side, however,
no unit or divider must stand higher
than the hob.
22
There must be a minimum distance
of 30 mm between the hob and adjacent furniture, (e.g. tall unit) owing
to the heat radiated from the elements.
Instructions for building-in
Instructions for building-in
For Australia only
Prepare the worktop cut-out as illustrated.
Dimension ”B“ applies for a combination of appliances and is given on
the chart.
b cooktop
c worktop
d removable barrier
For safety reasons, a removable barrier must be installed as shown to ensure that inadvertant contact with the
hot underside is prevented.
The distance between the lower
edge of the worktop and the upper
edge of the removable barrier must
be a minimum of 125 mm.
Instructions for building-in
Instructions for building-in
2 zone Combiset
1 element
2 elements
3 elements
4 elements
5 elements
Depth
in
mm
Width
(=
Dimension B)
in mm
490
490
490
490
490
265
558
851
1144
1437
490
490
490
560
1143
1728
Stick the seal provided f under the
edge of the hob.
4 zone Combiset
1 elements
2 elements
3 elements
Combination
One 2 zone
+ one 4 zone
490
851
Two 2 zone
+ one 4 zone
490
1143
Three 2 zone
+ one 4 zone
490
1437
One 2 zone
+ two 4 zone
490
1436
Two 2 zone
+ two 4 zone
490
1729
loosen
Extractor (e.g. DA 8-2)
For building in between two appliances:
- Dimension B increases by 90 mm.
For building in at the end of a combination:
- Dimension B increases by 98 mm.
tighten
b Appliance
c Tensioning screw
d Clamp
e Worktop
f Seal
Turn the tensioning screws c in the
clamps on the appliance b in an
anti-clockwise direction until a resistance is met and turn the clamps to
the left.
Place the appliance into position,
turn the clamps and tighten the tensioning screws until the clamps
press into the worktop e.
Connect the appliance to the electricity supply.
When building-in several Combiset
units, a spacer bar must be fitted between the units. It is supplied with its
own installation instructions.
24
25
26
27
Alteration rights reserved / 22
AUS, GB, IRL, NZ, ZA - 3297