Expand command - Canon USA, Inc.

EXPAND SERIAL COMMAD FUNCTIONAL SPECIFICATION for LV-5210/7215/7210
LV-5210/7215/7210
EXPAND SERIAL COMMAND
FUNCTIONAL SPECIFICATION
Page
1
EXPAND SERIAL COMMAD FUNCTIONAL SPECIFICATION for LV-5210/7215/7210
CONTENTS
1. Overtview
2. Serial Interface Specification
2.1 Communication Specification
2.2 Connection
3. Note for communications
4. Name Definition
5. Functional Execution Command table
5.1 Image Command Table
5.2 PC Control Command Table
5.3 VIDEO Control Command Table
5.4 Input Control Command Table
5.5 Screen Command Table
5.6 Lamp Command Table
5.7 Sound Command Table
5.8 Setting Command Table
6. Status Read Command Table
6.1 IMAGE Status Read Command table
6.2 PC Status Read Command Table
6.3 VIDEO Status Read Command Table
6.4 Input Status Read Command Table
6.5 Screen Status Read Command Table
6.6 Lamp Status Read Command Table
6.7 Sound Status Read Command Table
6.8 Setting Status Read Command Table
6.9 Other Status Read Command Table
7. Error Code Table
8. Functional Execution Command
8.1 Format
8.2 Transfer Example
8.3 Operation Requirements
8.4 Image Command
8.4.1
CF_BRIGHT COMMAND
8.4.2
CF_CONT COMMAND
8.4.3
CF_COLOR COMMAND
8.4.4
CF_TINT COMMAND
8.4.5
CF_SHARP COMMAND
8.4.6
CAMMA COMMAND
Page
2
EXPAND SERIAL COMMAD FUNCTIONAL SPECIFICATION for LV-5210/7215/7210
8.4.7
WBAL COMMAND
8.4.8
COLTEMP COMMAND
8.4.9
PROGV COMMAND
8.4.10 IMGE COMMAND
8.4.11 CF IMAGE ADJ COMMAND
8.5 PC Control command
8.5.1
CF_FSYNC COMMAND
8.5.2
CF_TDOTS COMMAND
8.5.3
CF_CLAMP COMMAND
8.5.4
CF_H-POS COMMAND
8.5.5
CF_V-POS COMMAND
8.5.6
CF_DDOTS COMMAND
8.5.7
CF_DLINE COMMAND
8.5.8
CF_PC STORE COMMAND
8.5.9
CF_PC MODE FREE COMMAND
8.6 VIDEO Control Command
8.6.1
CF_AVDDOTS COMMAND
8.6.2
CF_AVDLINECOMMAND
8.6.3
CF_AVHPOS COMMAND
8.6.4
CF_AVVPOS COMMAND
8.6.5
CF_AVSERV COMMAND
8.7 Input Control Command
8.7.1
CF_INPUT COMMAND
8.7.2
CF_SOURCE COMMAND
8.7.3
CF_INPUT_%1_%2 COMMAND
8.7.4
CF_SYSTEM COMMAND
8.8 Screen Control Command
8.8.1
CF_SCREEN COMMAND
8.8.2
CF_FLSCREN COMMAND
8.8.3
CF_UE COMMAND
8.8.4
CF_CENT COMMAND
8.8.5
CF_KEYSTONE COMMAND
8.8.6
CF_KYSTNMODE COMMAND
8.9 Lamp Command
8.9.1
CF_LAMOPH COMMAND
8.9.2
CF_ALMP MODE COMMAND
8.10 Sound Command
8.10.1 CF_VOLUME COMMAND
8.10.2 CF_MUTE COMMAND
Page
3
EXPAND SERIAL COMMAD FUNCTIONAL SPECIFICATION for LV-5210/7215/7210
8.11 Setting Command
8.11.1 CF_BBACK COMMAND
8.11.2 CF_DISPCOMMAND
8.11.3 CF_LOGOCOMMAND
8.11.4 CF_CEILCOMMAND
8.11.5 CF_REARCOMMAND
8.11.6 CF_RCODE COMMAND
8.11.7 CF_LANGCOMMAND
8.11.8 CF_ON-STACOMMAND
8.11.9 CF_P-MANECOMMAND
8.11.10 CF_P-MANETIMECOMMAND
8.11.11 CF_FANSPEEDCOMMAND
8.11.12 KEYDISCOMMAND
8.11.13 TERMINALCOMMAND
8.11.14 STANDBYMODEOCOMMAND
8.11.15 POINTERCOMMAND
8.11.16 FDEFAULTCOMMAND
8.11.17 LOGOCAPTURECOMMAND
9. Status Read Command
9.1 Format
9.2 Transfer Example
9.3 Operation Requirement
9.4 IMAGE COMMAND
9.4.1
CR-BRIGHTCOMMAND
9.4.2
CR-CONTCOMMAND
9.4.3
CR-COLORCOMMAND
9.4.4
CR-TINTCOMMAND
9.4.5
CR-SHARPCOMMAND
9.4.6
CR-GAMMACOMMAND
9.4.7
CR-WBAL-RCOMMAND
9.4.8
CR-WBAL-GCOMMAND
9.4.9
CR-WBAL-BCOMMAND
9.4.10 CR-COLTEMPCOMMAND
9.4.11 CR-PROGVCOMMAND
9.4.12 CR-IMAGECOMMAND
9.4.13 CR-IMGGMD COMMAND
9.5 PC COMMAND
9.5.1
CR-FSYNC COMMAND
9.5.2
CR-TDOTS COMMAND
Page
4
EXPAND SERIAL COMMAD FUNCTIONAL SPECIFICATION for LV-5210/7215/7210
9.5.3
CR-CLAMP COMMAND
9.5.4
CR-H-POS COMMAND
9.5.5
CR-V-POS COMMAND
9.5.6
CR-DDOTS COMMAND
9.5.7
CR-DLINECOMMAND
9.5.8
CR-PC STORECOMMAND
9.5.9
CR-SET PC ADJ COMMAND
9.6 Video Command
9.6.1
CR_SERSYSCOMMAND
9.7 Input Command
9.7.1
CR-INPUTCOMMAND
9.7.2
CR-COURCECOMMAND
9.7.3
CR-INPUT_%1COMMAND
9.7.4
CR-SYSTEMCOMMAND
9.8 Screen Command
9.8.1
CR-SCREENCOMMAND
9.8.2
CR-FLSCRENCOMMAND
9.8.3
CR-TRUECOMMAND
9.8.4
CR-KYSTONMODECOMMAND
9.9 Lamp COMMAND
9.9.1
CR_LAMPREPLCOMMAND
9.9.2
CR-LAMPMODECOMMAND
9.9.3
CR-PROJECOMMAND
9.10 Sound Status COMMAND
9.10.1 CR-VOLUMECOMMAND
9.10.2 CR-MUTECOMMAND
9.11 Setting Status COMMAND
9.11.1 CR-BBACKCOMMAND
9.11.2 CR-DISPCOMMAND
9.11.3 CR-RCODECOMMAND
9.11.4 CR-LANGCOMMAND
9.11.5 CR-ON-STACOMMAND
9.11.6 CR-P-MANE COMMAND
9.11.7 CR-P-MANETIMECOMMAND
9.11.8 CR-FANSPEEDCOMMAND
9.11.9 CR-KEYDISCOMMAND
9.11.10 CR-TERMINALCOMMAND
9.11.11 CR-STANDBYMODECOMMAND
9.11.12 CR-POINTERCOMMAND
Page
5
EXPAND SERIAL COMMAD FUNCTIONAL SPECIFICATION for LV-5210/7215/7210
9.12 Other Status Read Command
9.12.1 CR-SIGNAL COMMAND
9.12.2 CR-VMUTECOMMAND
9.12.3 CR-FREEZECOMMAND
9.12.4 CR-PTIMERCOMMAND
9.12.5 CR-TEMPWARNCOMMAND
9.12.6 CR-TEMPFAILCOMMAND
Page
6
EXPAND SERIAL COMMAD FUNCTIONAL SPECIFICATION for LV-5210/7215/7210
1
Outview
1.1 This Functional Specification defines communication functions such as Wireless Imager for
LV-5210/7215/7210.
1.2 The Projector Firmware Ver.1.x-ready.
1.3 Commands are to communicate to such as Wireless Imager, but most commands control a
remote projector with PC installed RS232C. That’s why commands are defined as expand
serial commands
2
Serial Interface Specification
2.1 Communication Specification
Specification
Synchro System
Asynchronou
Transmission
Speed
9600 / 19200
Data Length
8 bit
Parity
N/A
Stop Bit
1
Flow Control
N/A
Note1) transfer rate: initial setting value is 19200
Note2) transfer rate can be changed by service MODE
2.2 Connection
Must use a dedicated serial cable that come with the projector for a connection to a
COMPUTER and a projector.
PC
Projector
COM No.1
Control Port
CD
1
1
RXD
TXD
DTR
2
2
3
3
4
4
SG
5
5
DSR
RTS
6
6
7
7
CTS
RING
8
8
9
(D-Sub 9 Pin)
(Mini DIN 8 Pin)
Page
7
EXPAND SERIAL COMMAD FUNCTIONAL SPECIFICATION for LV-5210/7215/7210
3
Note for communications
3.1 The expand command is defined one Command/one line that starts ”C” and ends carriage
return (0x0D)
3.2 When a projector receives carriage return (0x0D), it starts decoding.
-Functional Execution
(Ex.) ”CF_BRIGHT_032” [CR]
-Status Read Command
(Ex.) “CR_RIGHT” [CR]
Note) _means a space
3.3 When it takes more than one second to receive one Command, it does not execute the Command.
Since the projector has received the first data “C”, when it takes more than 1 second until the
projector receives a carriage return (0x0D), it clears information of buffer.
3.4 When a COMPUTER keeps sending some Command, it must wait sending next command after
100ms when the COMPUTER receives the return command.
More than 100ms
Command
PC
Projector
Projector
“CF_BRIGHT_032” CR
Next Command
PC
“000” CR
Response
(A few ms -- 5s)
3.4.1
When a COMPUTER sends next command before receiving a return command, the
projector may not operate properly.
3.4.2
Except no response after 5 seconds
3.5 It takes about 5 seconds for internal initialization after plugging in AC.
During this time it
cannot process command. Do not issue any commands.
4
Name Definition
4.1 Data from a controller to a projector is represented as COMMAND, and data from a projector to
a controller for the incoming command is represented as RESPONSE.
4.2 [CR]: Carriage Return Code
The Command ends carriage return code. Also response Command ends carriage return, too.
4.3
: Space Code
All space Code is indicated by (_).
4.4
%1: Parameter in Command
When there are some parameters, the parameters are defined as %2, %3…
4.5
%%%: Error Code from a projector
“000”: Normal Reception
See “ 7.Error Code Table “ for error number.
4.6
%a : Parameter for response from a projector
When there are a few parameters, the parameter defines as %b, %c…
Page
8
EXPAND SERIAL COMMAD FUNCTIONAL SPECIFICATION for LV-5210/7215/7210
5
Functional Execution Command Table
5.1 Image Command Table
Execute Command
Item
CF_BRIGHT_%1 [CR]
Set Brightness value
CF_CONT_%1 [CR]
Set Contrast value
CF_COLOR_%1 [CR]
Set Color value
CF_TINT_%1 [CR]
Set Tint value
CF_SHARP_%1 [CR]
Set Sharpness value
CF_GAMMA_%1 [CR]
Set-GAMMA value
CF_WBAL-R_%1 [CR]
Set White Balance Red value
CF_WBAL-G_%1 [CR]
CF_WBAL-B_%1 [CR]
Set White Balance Green value
Set White Balance Blue value
CF_COLTEMP_%1 [CR]
CF_PROGV_%1 [CR]
Set Color Temp. value
Set or Cancel for Progressive
CF_IMAGE_%1 [CR]
Set Image MODE.
CF_IMAGEADJ_%1 [CR]
Reset and store for Image Adjustment.
5.2 PC Control Command Table
Execute Command
Item
CF_FSYNC_%1 [CR]
Set Fine Sync value.
CF_TDOTS_%1 [CR]
Set Total Dots value.
CF_CLAMP_%1 [CR]
Set Clamp value.
CF_H-POS_%1 [CR]
Set Horizontal Position value.
CF_V-POS_%1 [CR]
CF_DDOTS_%1 [CR]
Set Vertical Position value.
Set Display Dots value.
CF_DLINE_%1 [CR]
CF_PCSTORE_%1 [CR]
Set Display Line value.
Store e current PC Adj. Status to MODE 1, 2, 3, 4, or 5.
CF_PCMODEFREE_%1 [CR]
Reset MODE1, 2, 3, 4, and 5.
5.3 VIDEO Control Command Table
Execute Command
CF_AVDDOTS_%1 [CR]
CF_AVDLINE_%1 [CR]
CF_AVHPOS_%1 [CR]
CF_AVVPOS_%1 [CR]
CF_AVSERV_%1 [CR]
Item
Set AV Horizontal Resolution Value
Set AV Vertical Resolution Value
Set AV Horizontal Position Value.
Set AV Vertical Position Value.
Reset AV Horizontal /Vertical Resolution that are set in
such as CF_AVDDOTS/CF_AVDLINE to default
setting.
5.4 Input Control Command Table
Execute Command
CF_INPUT_%1 [CR]
CF_SOURCE_%1 [CR]
CF_INPUT_%1_%2 [CR]
CF_SYSTEM_%1 [CR]
Item
Select Input.
Select Input Sauce.
Select Input and Source.
Select System.
Page
9
EXPAND SERIAL COMMAD FUNCTIONAL SPECIFICATION for LV-5210/7215/7210
5.5 Screen Command Table
Execute Command
CF_SCREEN_%1 [CR]
CF_FLSCREN_%1 [CR]
CF_TRUE_%1 [CR]
CF_DZCENT_%1 [CR]
CF_KEYSTONE_%1 [CR]
CF_KYSTNMODE_%1 [CR]
Item
Select Screen size.
Set and Cancel Full Screen.
Set and Cancel True for Screen.
Cancel DIGITAL zooms.
Set Keystone
Set Keystone store MODE
5.6 Lamp Command Table
Execute Command
Item
CF_LAMPH_%1 [CR]
CF_LAMPMODE_%1 [CR]
Reset lamp total running time.
Select lamp MODE.
5.7 Sound Command Table
Execute Command
CF_VOLUME_%1 [CR]
CF_MUTE_%1 [CR]
Item
Set Volume value
Control Sound Mute ON/OFF
5.8 Setting Command Table
Execute Command
Item
CF_BBACK_%1 [CR]
CF_DISP_%1 [CR]
CF_LOGO_%1 [CR]
CF_CEIL_%1 [CR]
CF_REAR_%1 [CR]
CF_RCODE_%1 [CR]
CF_LANG_%1 [CR]
CF_ON-STA_%1 [CR]
CF_P-MANE_%1 [CR]
CF_P-MANETIME_%1 [CR]
CF_FANSPEED_%1 [CR]
Set Blue Back function.
Set Display function.
Set Logo function.
Set Ceiling function.
Set Rear Function.
Select Remote Control Reception Code.
Select OSD language.
Set Power ON Start Function.
Set Power management function.
Set Power management time
Select Fan Speed.
CF_KEYDIS_%1 [CR]
RC//KEY inhibit
CF_TERMINAL_%1 [CR]
CF_STANDBYMODE_%1 [CR]
CF_POINTER_%1_%2 [CR]
CF_FDEFAULT_%1 [CR]
CF_LOGOCAPTURE_%1 [CR]
Set TERMINAL.
Set STANDBYMODE
Set POINTER
Set Factory Default
Capture the current image on the screen.
Page
10
EXPAND SERIAL COMMAD FUNCTIONAL SPECIFICATION for LV-5210/7215/7210
6
Status Read Command Table
6.1 IMAGE Status Read Command Table
Status read command
CR_BRIGHT [CR]
CR_CONT [CR]
CR_COLOR [CR]
CR_TINT [CR]
CR_SHARP [CR]
CR_GAMMA [CR]
CR_WBAL-R [CR]
CR_WBAL-G [CR]
CR_WBAL-B [CR]
CR_COLTEMP [CR]
CR_PROGV [CR]
CR_IMAGE [CR]
CR_IMGGMD [CR]
Item
Get Brightness
Get Contrast
Get Color
Get Tint
Get Sharpness
Get-GAMMA
White Balance Red
White Balance Green
White Balance Blue
Get Color temperature setting value
Get Progressive setting value
Get Selected. Image
Get Image-GAMMA setting value
6.2 PC Status Read Command Table
Status read command
CR_FSYNC [CR]
CR_TDOTS [CR]
CR_CLAMP [CR]
CR_H-POS [CR]
CR_V-POS [CR]
CR_DDOTS [CR]
CR_DLINE [CR]
CR_PCSTORE [CR]
CR_SETPCADJ [CR]
Item
Get Fine Sync setting value
Get Total Dots setting value
Get Clamp setting value
Get Horizontal Position setting value
Get Vertical Position setting value
Get Display Dots setting value
Get Display Line setting value
Get Free or Store is selected. for PC Adj.; MODE 1-5.
Get current PC signal for PC display status.
6.3 VIDEO Status Read Command Table
Status read command
CR_SERSYS [CR]
Item
Get selected. current signal. When in AUTO MODE,
it returns a result by AUTO detect.
6.4 Input Status Read Command Table
Status read command
CR_INPUT [CR]
CR_SOURCE [CR]
CR_INPUT_%1 [CR]
CR_SYSTEM [CR]
Item
Get selected. input status
Get selected. input Source status
Get Input and the Source.
Get selected. system status in input MODE
6.5 Screen Status Read Command Table
Status read command
CR_SCREEN [CR]
CR_FLSCREN [CR]
CR_TRUE [CR]
CR_KYSTNMODE [CR]
Item
Get selected. screen size status
Get Full Screen MODE
Get True MODE Setting status.
Get Keystone Store MODE setting status
Page
11
EXPAND SERIAL COMMAD FUNCTIONAL SPECIFICATION for LV-5210/7215/7210
6.6 Lamp Status Read Command Table
Status read command
CR_LAMPREPL [CR]
CR_LAMPMODE [CR]
CR_PROJH [CR]
Item
Get information for lamp replacement time.
Get lamp MODE status
Get projector total running time.
6.7 Sound Status Read Command Table
Status read command
Item
CR_VOLUME [CR]
CR_MUTE [CR]
Get Volume value
Get sound mute setting value
6.8 Setting Status Read Command Table
Status read command
Item
CR_BBACK [CR]
CR_DISP [CR]
CR_LOGO [CR]
CR_RCODE [CR]
CR_LANG [CR]
CR_ON-STA [CR]
CR_P-MANE [CR]
CR_P-MANETIME [CR]
CR_FANSPEED [CR]
Get Blue Back setting value
Get Display setting value
Get Log setting value
Get selected. remote Control code status
Get selected. language.
Get ON Start setting status
Get Power management setting status
Get the start time for Power management
F Get selected. FAN CONTROL SPEED
CR_KEYDIS [CR]
Get RC/KEY prohibit status.
CR_TERMINAL [CR]
CR_STANDBYMODE [CR]
CR_POINTER [CR]
Get TERMINAL setting status.
Get STANDBYMODE Setting Status.
Get POINTER setting status.
6.9 Other Status Read Command Table
Status read command
CR_SIGNAL [CR]
CR_VMUTE [CR]
CR_FREEZE [CR]
CR_PTIMER [CR]
CR_TEMPWARN [CR]
CR_TEMPFAIL [CR]
Item
Get the status if there is signal or no signal
Get No Show setting status
Get Freeze Setting Status
Get Timer operational status
Get if sensors are exceeding critical temperature or not
Get the temperature when sensors approached critical
temperature
Page
12
EXPAND SERIAL COMMAD FUNCTIONAL SPECIFICATION for LV-5210/7215/7210
7
Error Code Table
Error/ode
?
000
101
102
103
201
301
303
Content
-When receives data that cannot be decoded
-Parameter determination error (digit number
error, and incorrect letter included)
NORMAL Reception(not error)
The function is not available in the selected.
MODE.
Selected. the value is out of range (Selected. value
will not be reflected)
Command mismatched to the Hardware.
(Command for unpopulated option function)
When sending command, the increment is
maximum value or the decrement is
minimum value.
Processing image capture. Re-try it again later.
Processing Memory Card Viewer. Re-try it again
later.
Page
13
EXPAND SERIAL COMMAD FUNCTIONAL SPECIFICATION for LV-5210/7215/7210
8
Functional Execution Command
8.1 Format
1. The following format’s commands issued form a PC
Pattern1:”CF_COMMAND” [CR]
Pattern2:”CF_COMMAND_%1” [CR]
CF_:Header
COMMAND:Letters
%1:Parameter(Letters)
_:Space(To separate COMMAND and parameter)
2. When a projector decoded a received data and ready to receive the next Command, it
will return acknowledgment.
“000” [CR]:(0x06,0x0D)When received Function Execute Command
“nnn” [CR]:Unable to execute any value except “000” value for any specific reason.
See the Ode/ode for its contents
3. When received an undecodable data
Returns”?” [CR]
8.2 Transfer Example
When setting projector total command to 1344 by expand command
PC
PJ :”CF_TDOTS_1344” [CR]
PC
PJ :”000” [CR] ---------------- Reception OK
8.3 Operation Requirements
When the functional execution command is limited, the projector sends an error command
as shown in the table below.
Projector Status
STANDBYMODE
Processing Count Down
Processing Cooling Down
Cooling
Down
due
to
abnormal
temperature
Abnormal Temperature
Abnormal Power
(60sECOnds after Power has turned to
abnormal)
Processing Power Save Cooling Down
Processing Power Save
Available Function Execution Command
C00:POWER ON
C00:POWER ON
(Terminate Count Down)
N/A
N/A
N/A
N/A
N/A
C00:POWER ON
C01:POWER OFF
Note): When the projector receives other commands in the above status, they return error
code to show the status.
Page
14
EXPAND SERIAL COMMAD FUNCTIONAL SPECIFICATION for LV-5210/7215/7210
8.4 IMAGE Command
8.4.1
CF_BRIGHT Command
COMMAND
%1
Details
Response
8.4.2
“000-063”------ Directly select the Bright Setting Value
“UP”---------------- Bright setting value +1
“DN”---------------- Bright setting value -1
Set the User control Bright Value
The value set by the command will not be saved to the projector. Therefore,
when ALL OFF the projector, the value will return to the original setting.
(For STANDBYMODE, this value stays.) Only valid when it is in the usual
Power ON State.
Acceptable
“000” [CR]
Unacceptable
“Error Code” [CR]
CF_CONTCOMMAND
COMMAND
%1
Details
Response
8.4.3
“CF_BRIGHT_%1” [CR]
“CF_CONT_%1” [CR]
“000-063”------ Directly select for conntrast setting value
“UP”---------------- Contrast setting value
“DN”---------------- Contrast setting value-1
Set the user Control contrast value.
The value set by this command will not be saved to the projector. Therefore,
when ALL OFF the projector, the value will return to the original setting
(For STANDBYMODE, this value stays.) Only valid when it is in the usual
Power ON status.)
Acceptable
“000” [CR]
Unacceptable
“Error Code” [CR]
CF_COLORCOMMAND
COMMAND
%1
Details
Response
“CF_COLOR_%1” [CR]
“000-063”------ Directly Color setting value
“UP”---------------- Color setting value+1
“DN”---------------- Color setting value-1
Set the user Control Color value.
The value set by this command will not be saved to the projector.
Therefore, when ALL OFF the projector, the value will return to the original
setting. (For STANDBYMODE, this value stays.) Only valid when it is in
the usual Power On state.
Acceptable
“000” [CR]
Unacceptable
“Error Code” [CR]
Page
15
EXPAND SERIAL COMMAD FUNCTIONAL SPECIFICATION for LV-5210/7215/7210
8.4.4
CF_TINTCOMMAND
COMMAND
%1
Details
Response
8.4.5
“000-063”------ Directly select for Tint setting value
“UP”---------------- Current Setting value +1
“DN”---------------- Current Setting value-1
Set the user Control tint value.
The value set by this command will not be save to the projector. Therefore,
when ALL OFF the projector, the value will return to the original setting.
(For STANDBYMODE, this value stays.) Only valid when it is in the
NORMAL Power ON state.
Acceptable
“000” [CR]
Unacceptable
“Error Code” [CR]
CF_SHARPCOMMAND
COMMAND
%1
Details
Response
8.4.6
“CF_TINT_%1” [CR]
“CF_SHARP_%1” [CR]
“000-015”------ Directly select for Gamma setting value
“UP”---------------- Current Sharpness setting value+1
“DN”---------------- Current_Sharpnes ssetting value -1
Set the user Control Sharpness value.
The value set by this Command will not be saved to the projector.
Therefore, when ALL OFF the projector, the value will return to the original
setting. (For STANDBYMODE, this value stays.) Only valid when it is
the usual Power ON state.
Acceptable
“000” [CR]
Unacceptable
“Error Code” [CR]
CF_GAMMACOMMAND
COMMAND
%1
Details
Response
“CF_GAMMA_%1” [CR]
“000-015”------ Directly select for-GAMMA setting value
“UP”-----------------GAMMA setting value+1
“DN”-----------------GAMMA setting value-1
Set the User Control-GAMMA Value
The value set by this Command will not be saved to the projector.
Therefore, when ALL OFF the projector, the value will return to the original
setting. (For STANDBYMODE, this value stays) Only valid when it is in
the usual Power On state.
Acceptable
“000” [CR]
Unacceptable
“Error Code” [CR]
Page
16
EXPAND SERIAL COMMAD FUNCTIONAL SPECIFICATION for LV-5210/7215/7210
8.4.7
CF_WBAL-COMMAND
COMMAND
%1
“R” ------------- RED
“G” ------------- GREEN
“B” ------------- BLUE
%2
“000-063”-- Directly select color value by White Balance %1 determination
“UP”------------ Color value for White Balance %1 determination +1
“DN”------------ Color value for White Balance %1 determination -1
Details
Response
8.4.8
Set the user Control value by white balance %1 determination.
The value set by this Command will not be saved to the projector.
Therefore, when ALL OFF the projector, the value will return to the original
setting. (For STANDBYMODE, this value stays.) Only valid when it is in
the usual Power On state.
Acceptable
“000” [CR]
Unacceptable
“Error Code” [CR]
CF_COLTEMP COMMAND
COMMAND
%1
Details
Response
8.4.9
“CF_WBAL-%1_%2” [CR]
“CF_COLTEMP_%1” [CR]
“000”........ XLow
“001”........ Low
“002”…….MID
“003”........ High
Set the Color Temp.(When it is in usual Power ON state, this is valid.)
The value set by this Command will not be saved to the projector.
Therefore, when ALL OFF the projector, the value will return to the original
setting. (For STANDBYMODE, this value stays.) Only valid when it is in
the usual Power On state.
Acceptable
“000” [CR]
Unacceptable
“Error Code” [CR]
CF_PROGV COMMAND
COMMAND
%1
Details
Response
“CF_PROGV_%1” [CR]
“L1”------ Select Progressive MODE L1
“L2”------ Select Progressive MODE L2
“OFF”----cancel Progressive
Set/Cancel for Progressive. (When it is in usual Power ON state, this is
valid.)
The value set by this Command will not be saved to the projector.
Therefore, when ALL OFF the projector, the value will return to the original
setting. (For STANDBYMODE, this value stays.) Only valid when it is in
the usual Power On state.
Acceptable
“000” [CR]
Unacceptable
“Error Code” [CR]
Page
17
EXPAND SERIAL COMMAD FUNCTIONAL SPECIFICATION for LV-5210/7215/7210
8.4.10 CF_IMAGECOMMAND
COMMAND
“CF_IMAGE_%1” [CR]
“STAND” ----- Standard(Image adjustment is set to factory default setting
value)
“REAL”
%1
------ High contrastl(Fixed value to display a graphic image with
natural tone.)
“CINEMA” ---- Cinema(Fixed value to focus on the tone reproduction for
movie.)
“CUSTOM1” -- Custom(the value is set and store by a user)
Details
Response
Select an Image MODE.(When it is in usual Power ON state, this is valid.)
Parameter “CUSTOM1” is the same as selecting custom”Custom1” on OSD
menu. The value set by this Command is stored in EEEPROM. When
ALL OFF the projector the value will return to the original setting.
Acceptable
“000” [CR]
Unacceptable
“Error Code” [CR]
8.4.11 CF_IMAGE ADJ COMMAND
COMMAND
%1
Details
Response
“CF_IMAGEADJ_%1” [CR]
“RST”------Reset Image adjustment
“STR1”----Store current image adjustment to Image 1
Reset or Store for image adjustment. (When it is in usual Power ON state,
this invalid.)
“STR1” is the same as “Custom” when choosing” Store” on OSD menu. The
setting value set in “Image1” to “Custom” is stored, so even if the projector is
set to ALL OFF and is turned on again, the setting value will be able to be
back.
Acceptable
“000” [CR]
Unacceptable
“Error Code” [CR]
8.5 PC Control COMMAND
8.5.1
CF_FSYNC COMMAND
COMMAND
%1
Details
Response
“CF_FSYNC_%1” [CR]
“0000-0031”---- Directly set Fine Sync setting value
“UP”------------------ Fine Sync setting value+1
“DN”------------------ Fine Sync setting value-1
Set Fine Sync for PC signal(Only valid when it is in the usual Power ON
status.)
The value set by this Command will not be saved to the projector.
Therefore, when ALL OFF the projector, the value will return to the original
setting.
(STANDBYMODE stays.)
Acceptable
“000” [CR]
Unacceptable
“101” [CR] ----Input is-VIDEO
Page
18
EXPAND SERIAL COMMAD FUNCTIONAL SPECIFICATION for LV-5210/7215/7210
8.5.2
CF_TDOTS COMMAND
COMMAND
“CF_TDOTS_%1” [CR]
“nnnn-9999”-- Directly set Total Dots value
%1
Details
Response
8.5.3
“UP”---------------- Total Dots setting value +1
“DN”---------------- Total Dots setting value-1
Set Total Dots of PC signal.(Only valid when it is in the usual Power ON
status.)
The value set by this Command will not be saved to the projector.
Therefore, when ALL OFF the projector, the value will return to the original
setting. (Standby MODE stays)
Acceptable
“000” [CR]
Unacceptable
“101” [CR] ----Input-VIDEO
CF_CLAMP COMMAND
COMMAND
%1
Details
Response
8.5.4
“nnnn” is minimum value.
This is current Display Dots value+Horizontal position value
“CF_CLAMP_%1” [CR]
“0000-0127”---- Directly set Clamp setting value
“UP”------------------ Clamp setting value +1
“DN”------------------ Clamp Setting value -1
Set Clamp of PC signal.(Only valid when it is in the usual Power ON status.)
The value set by this Command will not be saved to the projector..
Therefore, when ALL OFF the projector, the value will return to the
original setting.
(stay in STANDBYMODE.)
Acceptable
“000” [CR]
Unacceptable
“101” [CR] ----Input-VIDEO
CF_H-POS COMMAND
COMMAND
“CF_H-POS_%1” [CR]
“0000-nnnn”-- Directly set Horizontal Position
%1
Details
Response
“nnnn” means maximum value.
This result of current Total dots value-Display dots.
“UP”---------------- Horizontal Position value +1
“DN”---------------- Horizontal Position value-1
Set horizontal position of PC signal.(Only valid when it is in the usual Power
ON status.)
This value set by this Command will not be save do the projector.
Therefore, when ALL OFF the projector, the value will return to the original
setting. (stays in STANDBYMODE)
Acceptable
“000” [CR]
Unacceptable
“101” [CR] ----Input-VIDEO
Page
19
EXPAND SERIAL COMMAD FUNCTIONAL SPECIFICATION for LV-5210/7215/7210
8.5.5
CF_V-POS COMMAND
COMMAND
“CF_V-POS_%1” [CR]
“0000-nnnn”-- Directly set Vertical Position
“nnnn” means maximum value.
This value is from current Total Line value – display
Line value.
%1
“UP”---------------- Vertical Position setting value +1.
“DN”---------------- Vertical Position setting value-1
Details
Response
8.5.6
Set vertical position of PC signal. Only valid when it is in the usual Power
ON status.) The value set by this Command will not be saved to the
projector. Therefore, when ALL OFF the projector, the value will return to
the original setting. (stays in STANDBYMODE)
Acceptable
“000” [CR]
Unacceptable
“101” [CR] ----Input-VIDEO
CF_DDOTS COMMAND
COMMAND
“CF_DDOTS_%1” [CR]
“0100-nnnn”-- Directly set Display Dots value.
“nnnn” means maximum value.
This value is from current Total Dots value-Horizontal
position value
%1
“UP”---------------- Display Dots +1
“DN”---------------- Display Dots -1
Details
Response
8.5.7
et Display Dots of PC signal
The value set by this Command will not be saved to the projector.
Therefore, when ALL OFF the projector, the value will return to the original
setting. (stay in STANDBYMODE.)
(stays in STANDBYMODE.)
(Only valid when it is in the usual Power ON status.)
Acceptable
“000” [CR]
Unacceptable
“101” [CR] ----Input-VIDEO
CF_DLINECOMMAND
COMMAND
“CF_DLINE_%1” [CR]
“0100-nnnn”-- directly specify display Line value.
%1
Details
Response
“nnnn” means maximum.
This value is from current Total Line value – Vertical
Position value.
“UP”---------------- Display Line +1
“DN”---------------- Display Line -1
Set Display Line of PC signal(Only valid when it is in the usual Power ON
status.)
The value set by this Command will not be saved to the projector.
Therefore, when ALL OFF the projector, the value will return to the original
setting. (stays in STANDBYMODE.)
(stays in STANDBYMODE.)
Acceptable
“000” [CR]
Unacceptable
“101” [CR] ----Input-VIDEO
Page
20
EXPAND SERIAL COMMAD FUNCTIONAL SPECIFICATION for LV-5210/7215/7210
8.5.8
CF_PC STORECOMMAND
COMMAND
%1
Details
Response
8.5.9
“CF_PCSTORE_%1” [CR]
“MODE1”
“MODE2”
“MODE3”
“MODE4”
“MODE5”
--- Store current PC Adjust status to MODE 1
...Store current PC Adjust status to MODE 2
...Store current PC Adjust status to MODE 3
...Store current PC Adjust status to MODE 4
...Store current PC Adjust status to MODE 5
Store current PC Adjust status (each parameter status such as Total dots) to
MODE1-5.
This command operates the same operation as storing to MODE1-MODE5 in
PC Adjust Menu.
(Only valid when it is in the usual Power ON status.)
Acceptable
“000” [CR]
Unacceptable
“101” [CR] ----Input-VIDEO
CF_PC MODE FREECOMMAND
COMMAND
%1
Details
Response
“CF_PCMODEFREE_%1” [CR]
“MODE1” …reset MODE 1 to Free
“MODE2” …reset MODE 2 o Free
“MODE3” …reset MODE 3 o Free
“MODE4” …reset MODE 4 to Free
“MODE5” …reset MODE 5 to Free
Reset MODE 1, 2, 3, 4, and 5 to Free.
This command works as the same when resetting Modes in PC adjust menu.
(Only valid when it is in the usual Power ON status.)
Acceptable
“000” [CR]
Unacceptable
“101” [CR] ----Input-VIDEO
8.6 VIDEO Control COMMAND
8.6.1
CF_AVDDOTS COMMAND
COMMAND
%1
Details
Response
“CF_AVDDOTS_%1” [CR]
“UP”...........Current setting value +1
“DN”............Current setting value -1
Set AV Service MODE Horizontal Resolution.
(Only valid when it is in the usual Power ON status.)
The setting value is stored in EEPROM. When ALL OFF the projector, the
value will return to the original setting.
When there e is no signal, the projector returns “101” [CR].
Acceptable
“000” [CR]
Unacceptable
“101” [CR] ----Input-VIDEO
Page
21
EXPAND SERIAL COMMAD FUNCTIONAL SPECIFICATION for LV-5210/7215/7210
8.6.2
CF_AVDLINECOMMAND
COMMAND
%1
Details
Response
8.6.3
%1
Details
Response
Set AV service MODE vertical resolution value.
(Only valid when it is in the usual Power ON status.)
The setting value is stored in EEPROM. When ALL OFF the projector, the
value will return to the original setting.
When there is no signal, the projector returns “101” [CR].
Acceptable
“000” [CR]
Unacceptable
“101” [CR] ----Input-VIDEO
“CF_AVHPOS_%1” [CR]
“UP”............Current Setting+1
“DN”............Current Setting-1
Set AV service MODE horizontal position value.
(Only valid when it is in the usual Power ON status.)
The setting value is stored in EEPROM. When ALL OFF the projector, the
value will return to the original setting.
When there is no signal, the projector returns “101” [CR].
Acceptable
“000” [CR]
Unacceptable
“101” [CR] ----Input S-VIDEO
CF_AVVPOS COMMAND
COMMAND
%1
Details
Response
8.6.5
“UP”............Current Setting+1
“DN”............Current Setting-1
CF_AVHPOS COMMAND
COMMAND
8.6.4
“CF_AVDLINE_%1” [CR]
“CF_AVVPOS_%1” [CR]
“UP”............Current Setting+1
“DN”............Current Setting-1
Set AV service MODE vertical position value.
(Only valid when it is in the usual Power ON status.)
The setting value is stored in EEPROM. When ALL OFF the projector, the
value will return to the original setting.
When there is no signal, the projector returns “101” [CR].
Acceptable
“000” [CR]
Unacceptable
“101” [CR] ----Input-VIDEO
CF_AVSERV COMMAND
COMMAND
%1
“CF_AVSERV_%1” [CR]
“RST”
Set AV horizontal/vertical resolution that is set in such as “CF_A V
Details
DDOTS”/”CF_AVDLINE” to default setting value.
(Only valid when it is in the usual Power ON status.)
The setting value is stored in EEPROM. When ALL OFF the projector, the
value will return to the original setting.
When there is no signal, the projector returns “101” [CR].
Page
22
EXPAND SERIAL COMMAD FUNCTIONAL SPECIFICATION for LV-5210/7215/7210
Response
Acceptable
“000” [CR]
Unacceptable
“101” [CR] ----Input-VIDEO
8.7 Input Control COMMAND
8.7.1
CF_INPUT COMMAND
COMMAND
%1
Details
Response
8.7.2
“CF_INPUT_%1” [CR]
“COMPUTER1”........ Select COMPUTER 1 input
“COMPUTER2”........ COMPUTER 2 input
“VIDEO”........................ VIDEO input
Select Input.(Only valid when it is in the usual Power ON status.)
The Command works as the same as the remote controls’s unit “INPUT”
button.
Note1:) If trying to select Input-2 TERMINAL when setting
Input-2(COMPUTER)to MONITOR Out, the projector returns “101”.
Note2:)The selection of Input-1 is not COMPUTER-1 but Memory card/
Wireless/Network when Option box is installed to Input-1 (COMPUTER1).
Acceptable
“000” [CR]
Unacceptable
“%%%” [CR]
CF_SOURCECOMMAND
COMMAND
%1
Details
Response
“CF_SOURCE_%1” [CR]
Input=1
“DIGITAL”…………Select DVI input
“ANALOG”............ .Select ANALOG input 0
“HDCP”....................Select DVI HDCP input
Input=2
“ANALOG”............Select RGB
“YPBPR”................Select Component VIDEO input
“SCART”................ Select Scart input
Input=3
“AUTO”..................Select VIDEO Auto MODE
“VIDEO”................ Select Composite VIDEO input
“S-VIDEO”......…… Select S-VIDEO input
Select current input source.
(Only valid when it is in the usual Power ON status.)
When selected Input and specified %1 are not matched, the projector
returns”101” and does not execute the command.
Note) When the option, MCI BOX is installed to Input-1 (COMPUTER1),
selection for source is invalid.
error code “101”
Acceptable
“000” [CR]
Unacceptable
“%%%” [CR]
Page
23
EXPAND SERIAL COMMAD FUNCTIONAL SPECIFICATION for LV-5210/7215/7210
8.7.3
CF_INPUT_%1_%2 COMMAND
COMMAND
%1
“COMPUTER1”.... Select COMPUTER 1 input
“COMPUTER2”.... Select COMPUTER 2 input
“VIDEO”.................... Select VIDEO input
%2
When %1 is COMPUTER1…
“ANALOG”............ Select ANALOG RGB input
“DIGITAL”......……Select DIV input
“HDCP”.................... Select DCHP input
When %1 is COMPUTER2
“ANALOG”............Select ANALOG RGB input
“YPBPR”................Select Component input
“SCART”................ Select SCART input
When %1 is VIDEO
“AUTO”..................Select VIDEO AUTO MODE
“VIDEO”................ Select VIDEO
“S-VIDEO”......…… Select S-VIDEO
Details
Response
8.7.4
“CF_INPUT_%1_%2” [CR]
Select Input and also the source that is specified in %2.
(Only valid when it is in the usual Power ON status.)
Acceptable
“000” [CR]
Unacceptable
“%%%” [CR]
CF_SYSTEMCOMMAND
COMMAND
“CF_SYSTEM_%1” [CR]
Input is PC
%1
Input-VIDEO
Details
“MODE1”------ Select MODE 1
“MODE2”------ Select MODE 2
“MODE3”------ Select MODE 3
“MODE4”------ Select MODE 4
“MODE5”------ Select MODE 5
“AUTO”-------- Select System” AUTO”
“NTSC”-------- Select NTSC
“NTSC443”-- Select NTSC4.43
“PAL”---------- Select PAL
“SECAM”------ Select SECAM
“PAL-M”------ Select PAL-M
“PAL-N”------ Select PAL-N
“1080I”------ Select 1080i
“1035I”------ Select 1035i
“720P”-------- Select 720p
“575P”-------- Select 575p
“480P”-------- Select 480p
“575I”-------- Select 575i
“480I”-------- Select 480i
Select current Input system.
(Only valid when it is in the usual Power ON status.)
When Input does not meet the requirement for specified %11, the response
will be “101” and the Command does not execute.
Note 1) “NTSC” / “NTSC4.43” / “PAL” / “SECAM” / “PAL-M” / “PAL-N” is
available only when Input-VIDEO or S-VIDEO.
Note 2) “1080I” / “1035I” / “720p” / “575P” / “480P” / “575I” / “480I” is
available only when Input is Y, Pb/Cb, Pr/Cr.
Page
24
EXPAND SERIAL COMMAD FUNCTIONAL SPECIFICATION for LV-5210/7215/7210
Response
Acceptable
“000” [CR]
Unacceptable
“Error Code” [CR]
8.8 Screen Control COMMAND
8.8.1
CF_SCREENCOMMAND
COMMAND
%1
“CF_SCREEN_%1” [CR]
Input is
COMPUTER
Input is
VIDEO
Details
Response
8.8.2
“NORMAL” ---- Select 4:3
“WIDE” -------- Select 16:9 screen
Select screen size.(Only valid when it is in the usual Power ON status.)
When Input does not meet the requirement for the specified %1, the response
will be “101” [CR], and the Command is not executed.
Acceptable
“000” [CR]
Unacceptable
“Error Code” [CR]
CF_FLSCRENCOMMAND
COMMAND
%1
Details
Response
8.8.3
“NORMAL”............Select 4:3
“WIDE”.................... Select 16:9
“TRUE”.................... Select TRUE
“DZOOM_UP”.... Zoom Out with DIGITAL zoom
“DZOOM□DN”-- Zoom in with DIGITAL zoom
“CF_FLSCREN_%1” [CR]
“ON”------ Select Full Screen
“OFF”---- Cancel Full Screen
Input is
COMPUTER
Set/Cancel Full Screen. (Only valid when it is in the usual
Power ON status.)
The value set by this Command will not be saved to the
projector.
Therefore, when ALL OFF the projector, the value will
return to the original setting. (stay in STANDBYMODE.)
(stays in STANDBYMODE.)
Input-VIDEO
series
Invalid
Acceptable
“000” [CR]
Unacceptable
“Error Code” [CR]
CF_TRUECOMMAND
COMMAND
“CF_TRUE_%1” [CR]
%1
“ON”------ Select True
“OFF”---- Cancel True
Details
Response
T Set/Cancel True
Only valid when it is in the usual Power On state and input is COMPUTER.
Acceptable
“000” [CR]
Unacceptable
“101” [CR] ........ Input-VIDEO
Page
25
EXPAND SERIAL COMMAD FUNCTIONAL SPECIFICATION for LV-5210/7215/7210
8.8.4
CF_DZCENTCOMMAND
COMMAND
%1
Details
Response
8.8.5
“CENT”-----Cancel DIGITAL Zoom (CENT : “CENTER”)
Cancel DIGITAL Zoom
Only valid when it is n the usual Power ON state and Input is COMPUTER.
Acceptable
Acceptable
Unacceptable
Unacceptable
CF_KEYSTONECOMMAND
COMMAND
“CF_KEYSTONE_%1” [CR]
%1
“UP”-------- Make the screen image length at the top edge shorter with small
range.
“FUP” ----- Make the screen image length at the top edge shorter with large
range.
“DN” ------ Make the screen image length at the bottom edge shorter with
small range.
“FDN”----- Make the screen image length at the bottom edge shorter with
large range.
“LEFT”---- Make the screen image length at the left edge shorter with small
range.
“FLFT”---- Make the screen image length at the left shorter with large range.
“RIGHT”-- Make the screen image length at the right edge shorter with
small range.
“FRGT”----Make the screen image length at the right edge shorter with large
range.
“RST”----- Keystone off
Details
Change Keystone range.(Only valid when it is in the usual Power ON
status.)
Response
8.8.6
“CF_DZCENT_%1” [CR]
Acceptable
“000” [CR]
Unacceptable
“Error Code” [CR]
“201” [CR] .... When Keysotne value is maximum or
minimum.
CF_KYSTNMODECOMMAND
COMMAND
%1
Details
Response
“CF_KYSTONMODE_%1” [CR]
“STR”------ Set Keystone store MODE to Store
“RST” ----- Set Keystone store MODE to Reset
Set Keystone store MODE(Only valid when it is in the usual Power ON
status.)
Acceptable
“000” [CR]
Unacceptable
“Error Code” [CR]
Page
26
EXPAND SERIAL COMMAD FUNCTIONAL SPECIFICATION for LV-5210/7215/7210
8.9 Lamp COMMAND
8.9.1
CF_LAMPH COMMAND
COMMAND
%1
Details
Response
8.9.2
“RST”
Reset total lamp running time. (Only valid when it is in the usual Power ON
status.)
Acceptable
“000” [CR]
Unacceptable
“Error Code” [CR]
CF_LAMP MODECOMMAND
COMMAND
%1
Details
Response
8.10
“CF_LAMPPH_%1” [CR]
“CF_LAMPHMODE_%1” [CR]
“NORMAL”-- Set lamp to NORMAL MODE
“ECO”-------- Set lamp to silent MODE.
“AUTO”------ Set lamp to AUTO MODE
Select lamp MODE. (Only valid when it is in the usual Power ON status.)
The value set is stored in EEPROM. When ALL OFF the projector, the
value will return to the original setting.
Acceptable
“000” [CR]
Unacceptable
“Error Code” [CR]
Sound COMMAND
8.10.1 CF_VOLUMECOMMAND
COMMAND
%1
Details
Response
“CF_VOLUME_%1” [CR]
“000-063”------ Directly set Volume value
“UP”---------------- Volume setting value +1.
“DN”---------------- Volume setting value -1.
Control Volume setting value. (Only valid when it is in the usual Power ON
status.)
The same operation as a remote Control’s turning up/down the volume.
Also, the Command directly sets the volume value.
When setting volume value like remote Control unit” operation, Sound Mute
ON will be canceled. The setting value will be stored in a projector.
Acceptable
“000” [CR]
Unacceptable
“Error Code” [CR]
8.10.2 CF_MUTECOMMAND
COMMAND
%1
Details
“CF_MUTE_%1” [CR]
“ON”------ set Sound Mute to ON
“OFF”---- set Sound Mute to OFF
Control Sound Mute ON/OFF.(Only valid when it is in the usual Power ON
status.)
Page
27
EXPAND SERIAL COMMAD FUNCTIONAL SPECIFICATION for LV-5210/7215/7210
Response
8.11
Acceptable
“000” [CR]
Unacceptable
“Error Code” [CR]
Setting COMMAND
8.11.1 CF_BBACK COMMAND
COMMAND
%1
Details
Response
“CF_BBACK_%1” [CR]
“ON”------ Select Blue Back
“OFF”---- Cancel Blue Back
Set/cancel Blue Back. (Only valid when it is in the usual Power ON status.)
The value set is stored in EEPROM. When ALL OFF the projector, the
value will return to the original setting.
Acceptable
“000” [CR]
Unacceptable
“Error Code” [CR]
8.11.2 CF_DISPCOMMAND
COMMAND
%1
Details
Response
“CF_DISP_%1” [CR]
“ON”------ Select Display
“OFF”----Cancel Display
Set/Cancel Display. (Only valid when it is in the usual Power ON status.)
The value set is stored in EEPROM. When ALL OFF the projector, the
value will return to the original setting.
Acceptable
“000” [CR]
Unacceptable
“Error Code” [CR]
8.11.3 CF_LOGOCOMMAND
COMMAND
%1
Details
Response
“CF_LOGO_%1” [CR]
“OFF”.................... Cancel Logo
“DEFAULT”.... Set Default Logo Display
“USER”................ Set Captured Logo Display
Set/Cancel Logo. (Only valid when it is in the usual Power ON status.)
The value set is stored in EEPROM. When ALL OFF the projector, the
value will return to the original setting.
Acceptable
“000” [CR]
Unacceptable
“Error Code” [CR]
8.11.4 CF_CEILCOMMAND
COMMAND
%1
Details
Response
“CF_CEIL_%1” [CR]
“ON”------ Select Ceiling
“OFF”---- Cancel Ceiling
Set/Cancel Ceiling (Only valid when it is in the usual Power ON status.)
The value set is stored in EEPROM. When ALL OFF the projector, the
value will return to the original setting.
Acceptable
“000” [CR]
Unacceptable
“Error Code” [CR]
Page
28
EXPAND SERIAL COMMAD FUNCTIONAL SPECIFICATION for LV-5210/7215/7210
8.11.5 CF_REARCOMMAND
COMMAND
“CF_REAR_%1” [CR]
%1
“ON”------ Select Rear
“OFF”---- Cancel Rear
Details
Response
Set/Cancel Rear (Only valid when it is in the usual Power ON status.)
When Rear is ON, it will be a mirror-reversed image.
The value set is stored in EEPROM. When ALL OFF the projector, the
value will return to the original setting.
Acceptable
“000” [CR]
Unacceptable
“Error Code” [CR]
8.11.6 CF_RCODECOMMAND
COMMAND
%1
Details
Response
“CF_RCCODE_%1” [CR]
“001”------Select Code 1
“002”------Select Code 2
“003”------Select Code 3
“004”------Select Code 4
“005”------Select Code 5
“006”------Select Code 6
“007”------Select Code 7
“008”------Select Code 8
Select a remote Control code.(Only valid when it is in the usual Power ON
status.)
The value set is stored in EEPROM. When ALL OFF the projector, the
value will return to the original setting.
Acceptable
“000” [CR]
Unacceptable
“Error Code” [CR]
8.11.7 CF_LANGCOMMAND
COMMAND
%1
Details
Response
“CF_LANG_%1” [CR]
“ENG”---- Select English
“DEU”---- Select German
“FRA”---- Select French
“ITA”---- Select Italy
“ESP”---- Select Spanish
“POR”---- Select Portuguese
“NED”---- Select Dutch
“SVE”---- Select Swedish
“JPN”---- Select Japanese
“CHI”---- Select Chinese
“KOR”---- Select Korean
“RUS”---- Select Russian
Set OSD language. (Only valid when it is in the usual Power ON status.)
The value set is stored in EEPROM. When ALL OFF the projector, the
value will return to the original setting.
Acceptable
“000” [CR]
Page
29
EXPAND SERIAL COMMAD FUNCTIONAL SPECIFICATION for LV-5210/7215/7210
Unacceptable
“Error Code” [CR]
8.11.8 CF_ON-STACOMMAND
COMMAND
%1
Details
Response
“CF_ON-STA_%1” [CR]
“ON”------ Select Power On Start
“OFF”---- Cancel Power On Start
Set/Cancel Power ON Start. (Only valid when it is in the usual Power ON
status.)
The value set is stored in EEPROM. When ALL OFF the projector, the
value will return to the original setting.
Acceptable
“000” [CR]
Unacceptable
“Error Code” [CR]
8.11.9 CF_P-MANECOMMAND
COMMAND
%1
Details
Response
“CF_P-MANE_%1” [CR]
“OFF”------------ Set Power management to OFF
“READY”-------- Set Power management to Ready
“SHUTDOWN”-- Set Power management to Shut Down
Set/Cancel Power management.(Only valid when it is in the usual Power ON
status.)
The value set is stored in EEPROM. When ALL OFF the projector, the
value will return to the original setting.
Acceptable
“000” [CR]
Unacceptable
“Error Code” [CR]
8.11.10 CF_P-MANETIMECOMMAND
COMMAND
%1
Details
Response
“CF_P-MANETIME_%1” [CR]
“01”-”30”-- Directly set the time by the minute
“UP”------------ Set the time 1 minute longer
“DN”------------ Set the time 1 minute shorter
Set Power management time. (Only valid when it is in the usual Power ON
status.)
The value set is stored in EEPROM. When ALL OFF the projector, the
value will return to the original setting.
Acceptable
“000” [CR]
Unacceptable
“Error Code” [CR]
8.11.11 CF_FANSPEEDCOMMAND
COMMAND
%1
Details
“CF_FANSPEED_%1” [CR]
“MAX”------Select maximum speed
“NOR”------Select NORMAL speed
Change Fan Control speed.
Only valid when it is in the usual Power ON
status.)
The value set is stored in EEPROM When ALL OFF the projector the
Page
30
EXPAND SERIAL COMMAD FUNCTIONAL SPECIFICATION for LV-5210/7215/7210
value will return to the original setting.
Response
Acceptable
“000” [CR]
Unacceptable
“Error Code” [CR]
8.11.12 CF_KEYDISCOMMAND
COMMAND
%1
Details
Response
“CF_KEYDIS_%1” [CR]
N/A” --- RC and KEY are available
“RC”
...Bar the use of RC
“KEY”
...Bar the use of KEY
Set bar the use of RC/KEY. (Only valid when it is in the usual Power ON
status.)
Acceptable
“000” [CR]
Unacceptable
“Error Code” [CR]
8.11.13 CF_TERMINALCOMMAND
COMMAND
%1
Details
Response
“CF_TERMINAL_%1” [CR]
“COMPUTER”...... Set Input mode
“MONITOR”.......... Set Monitor Out Mode
Set TERMINAL(Only valid when it is in the usual Power ON status.)
In this model, Terminal is COMPTUER2.
Acceptable
“000” [CR]
Unacceptable
“Error Code” [CR]
8.11.14 CF_STANDBYMODECOMMAND
COMMAND
%1
Details
Response
“CF_STANDBYMODE_%1” [CR]
“ECO”................ Standby power requirement is smaller
“NORMAL”.... Normal Standby power requirement
Set STANDBYMODE (Only valid when it is in the usual Power ON status.)
Acceptable
“000” [CR]
Unacceptable
“Error Code” [CR]
8.11.15 CF_POINTERCOMMAND
COMMAND
“CF_POINTER_%1_%2” [CR]
%1
“SPOTLIGHT”..…….. Select Spotlight
“ARROW”.................... Select Arrow
“FINGER”..............…. Select Finger
“LASER”.................... Select Laser mark
%2
“MAX”............................ Maximum Spotlight
“MID”............................ Medium Spotlight
“MIN”............................ Minimum Spotlight
Details
Select POINTER image (Only valid when it is in the usual Power ON
status.)
Note1) %2 is available when “SPOTLIGHT” is specified only.
When ”ARROW”/”FINGER”/”LASER”, specify ”CF_POINTER_%1” [CR].
Note2) When “SPOTLIGHT”, %2 cannot be omitted.
Page
31
EXPAND SERIAL COMMAD FUNCTIONAL SPECIFICATION for LV-5210/7215/7210
Response
Acceptable
“000” [CR]
Unacceptable
“Error Code” [CR]
8.11.16 CF_FDEFAULTCOMMAND
COMMAND
%1
Details
Response
“CF_FDEFAULT_%1” [CR]
“RST”
Set Factory Default. (Only valid when it is in the usual Power ON status.)
Acceptable
“000” [CR]
Unacceptable
“Error Code” [CR]
8.11.17 CF_LOGOCAPTURECOMMAND
COMMAND
“CF_LOGOCAPTURE_%1” [CR]
%1
“START”.................. Capture ON
Details
Response
Capture the current image on screen.
When beginning to capture the image, any command is not available until
the capture has done. When sending the command during the process, the
projector returns the error code, “301”.
Acceptable
“000” [CR]
Unacceptable
“Error Code” [CR]
Page
32
EXPAND SERIAL COMMAD FUNCTIONAL SPECIFICATION for LV-5210/7215/7210
9
Status Read Command
9.1 FORMAT
1. PC issues Commands as below
“CR_COMMAND” [CR]
COMMAND: Character Line
2. When projector receives the appropriate Command, it returns a character line as the
required data.
“000_”%1 [CR]
%1:Required Data (character line)
3.
When receiving data cannot be decode, the projector returns ”?” [CR]
9.2 Transfer Example
Get total dots of projector by expand Commands
PC
PJ :”CR TDOTS” [CR]
PC
PJ :”000 1344” [CR]
9.3 Operation Requirement
Should be always operated
9.4 IMAGECOMMAND
9.4.1
CR_BRIGHTCOMMAND
COMMAND
Details
“CR_BRIGHT” [CR]
Get Contrast of user Control
Acceptable
Response
%a
Unacceptable
9.4.2
“000”-- ”063”
“?” [CR]
CR_CONTCOMMAND
COMMAND
Details
“CR_CONT” [CR]
Get Contrast of user Control
Acceptable
Response
%a
Unacceptable
9.4.3
“000_%a” [CR]
“000_%a” [CR]
“000”-- ”063”
“?” [CR]
CR_COLORCOMMAND
COMMAND
Details
“CR_COLOR” [CR]
Get Color value of user Control
Acceptable
Response
%a
Unacceptable
“000_%a” [CR]
“000”-- ”063”
“?” [CR]
Page
33
EXPAND SERIAL COMMAD FUNCTIONAL SPECIFICATION for LV-5210/7215/7210
9.4.4
CR_TINTCOMMAND
COMMAND
Details
“CR_TINT”[CR]
Get Tint value of user Control
Acceptable
Response
%a
Unacceptable
9.4.5
Details
Response
Get SHARPNESS value of user Control
%a
Unacceptable
“000_%a” [CR]
“000”-- ”015”
“?” [CR]
CR_GAMMACOMMAND
COMMAND
Details
“CR_GAMMA” [CR]
Get-GAMMA value of user Control
Acceptable
Response
%a
Unacceptable
“000_%a” [CR]
“000”-- ”015”
“?” [CR]
CR_WBAL-RCOMMAND
COMMAND
Details
“CR_WBAL-R” [CR]
Get White Balance Red value of user Control
Acceptable
Response
%a
Unacceptable
9.4.8
“Error code”[CR] --- invalid
“?”[CR] ------------- When receives unclear command
“CR_SHARP” [CR]
Acceptable
9.4.7
“000”-- ”063”
CR_SHARPCOMMAND
COMMAND
9.4.6
“000_%a”[CR]
“000_%a” [CR]
“000”-- ”063”
“?” [CR]
CR_WBAL-GCOMMAND
COMMAND
Details
“CR_WBAL-G” [CR]
Get White Balance Green of user Control
Acceptable
Response
%a
Unacceptable
“000_%a” [CR]
“000”-- ”063”
“?” [CR]
Page
34
EXPAND SERIAL COMMAD FUNCTIONAL SPECIFICATION for LV-5210/7215/7210
9.4.9
CR_WBAL-BCOMMAND
COMMAND
Details
“CR_WBAL-B” [CR]
Get White Balance Blue of user Control
Acceptable
Response
%a
Unacceptable
“000_%a” [CR]
“000”-- ”063”
“?” [CR]
9.4.10 CR_COLTEMPCOMMAND
COMMAND
Details
“CR_COLTEMP” [CR]
Get Color Temp setting status
Acceptable
Response
%a
Unacceptable
“000_%a” [CR]
“000”............ XLow
“001”............ Low
“002”………..Mid
“003”............ High
“ADJ”............Processing White Balance Adjustment
“?” [CR]
9.4.11 CR_PROGVCOMMAND
COMMAND
Details
“CR_PROGV” [CR]
Get Progressive setting status
Acceptable
Response
%a
Unacceptable
“000_%a” [CR]
“L1”----- Progressive MODE L1 setting
“L2”----- Progressive MODE L2settiing
“OFF”--- Progressive cancellation
“?” [CR]
9.4.12 CR_IMAGECOMMAND
COMMAND
Details
“CR_IMAGE” [CR]
Get image setting status
Required data “CUSTOM1” is the same as “IMAGE1” to “CUSTOM” on OSD
menu.
Acceptable
Response
%a
Unacceptable
“000_%a” [CR]
“STAND”-------------------------- Standard
“REAL” -------------------------- High Contrast
“CINEMA”------------------------ Cinema
“CUSTOM1” ---------------------Custom
“Error code” [CR] ---- Invalid
“?” [CR] -------------- When the projector received unclear
command
Page
35
EXPAND SERIAL COMMAD FUNCTIONAL SPECIFICATION for LV-5210/7215/7210
9.4.13 CR_IMGGMD COMMAND
COMMAND
Details
“CR_IMGGMD” [CR]
Get Standard/High Contrast/Cinema for image-GAMMA setting.
Acceptable
Response
%a
Unacceptable
“000_%a” [CR]
“STD”=Standard
“REL”=High Contrast
“CNM”=Cinema
“?” [CR]
9.5 PC COMMAND
9.5.1
CR_FSYNC COMMAND
COMMAND
Details
“CR_FSYNC” [CR]
Get Fine Sync value
Acceptable
Response
%a
Unacceptable
9.5.2
“0000”-- ”0031”
“Error code” [CR] ---- Invalid
“?” [CR] -------- When the projector received unclear command
CR_TDOTS COMMAND
COMMAND
Details
“CR_TDOTS” [CR]
Get Total Dots value
Acceptable
Response
%a
Unacceptable
9.5.3
“000_%a” [CR]
“000_%a” [CR]
“nnnn”-”9999”
(nnnn = Display Dots + Horizontal Position)
“Error code” [CR] ---- Invalid
“?” [CR] -------- When the projector received unclear command
CR_CLAMP COMMAND
COMMAND
Details
“CR_CLAMP” [CR]
Get Clamp value
Acceptable
Response
%a
Unacceptable
“000_%a” [CR]
“0000”-- ”0127”
“Error code” [CR] ---- Invalid
“?” [CR] -------- When the projector received unclear command
Page
36
EXPAND SERIAL COMMAD FUNCTIONAL SPECIFICATION for LV-5210/7215/7210
9.5.4
CR_H-POS COMMAND
COMMAND
Details
“CR_H-POS” [CR]
Get Horizontal Position value
Acceptable
Response
%a
Unacceptable
9.5.5
Details
“Error code” [CR] ---- Invalid
“?” [CR] -------- When the projector received unclear command
“CR_V-POS” [CR]
Get Vertical Position value
Acceptable
Response
%a
Unacceptable
“000_%a” [CR]
“0000”-- ”nnnn”
(nnnn = Total Line - Display Line)
“Error code” [CR] ---- Invalid
“?”[CR] -------- When the projector received unclear command
CR_DDOTS COMMAND
COMMAND
Details
“CR_DDOTS” [CR]
Get Display Dots value
Acceptable
Response
%a
Unacceptable
9.5.7
“0000”-”nnnn”
(nnnn = Total Dots - Display Dots)
CR_V-POS COMMAND
COMMAND
9.5.6
“000_%a” [CR]
“000_%a” [CR]
“0100”-”nnnn”
(nnnn = Total Dots – Horizontal Position value)
“Error code” [CR] ---- Invalid
“?” [CR] -------- When the projector received unclear command
CR_DLINECOMMAND
COMMAND
Details
“CR_DLINE” [CR]
Get Display Line value
Acceptable
Response
%a
Unacceptable
“000_%a” [CR]
“0100”-”nnnn”
(nnnn = Total Line – Vertical Position value
“Error code” [CR] ---- Invalid
“?” [CR] -------- When the projector received unclear command
Page
37
EXPAND SERIAL COMMAD FUNCTIONAL SPECIFICATION for LV-5210/7215/7210
9.5.8
CR_PC STORECOMMAND
COMMAND
Details
Response
9.5.9
“CR_PCSTORE” [CR]
Get the status if MODE1-MODE5 is Free or Stored for PC Adjust.
Each data MODE1-MODE5 will be shown in 5 bytes.
(F:Free, S:Stored)
Acceptable
“000_%a” [CR]
Required
Data
“FFFFF”--- All Free
“SFFFF”--- Only MODE1 is Stored, and others are Free
:
“FFFFS”--- Only MODE5 is Stored, and others are Free
“SSSSS”--- All Stored
Unacceptable
“?” [CR]
CR_SET PC ADJ COMMAND
COMMAND
Details
“CR_SETPCADJ” [CR]
Get PC signal for current system
Acceptable
Response
%1
Unacceptable
“000_%1” [CR]
“XGA1”
“HDTV1080”
“MODE1””-- “MODE5” ...Etc.
“?” [CR]
9.6 VIDEO COMMAND
9.6.1
CR_SERSYSCOMMAND
COMMAND
Details
“CR_SERSYS” [CR]
Select selected. signal.
When AUTO MODE, it returns by AUTO-detect.
Only available when Input-VIDEO. (Unavailable
COMPUTER.)
Acceptable
Response
%a
Unacceptable
when
Input
is
“000_%a” [CR]
“1080I60”-- 1080i 60Hz
“1080I50”-- 1080i 50Hz
“1035I”------ 1035i
“720P”-------- 720p
“575P”-------- 575p
“480P”-------- 480p
“575I”-------- 575i(include composite signal such as PAL)
“480I”-------- 480i(include composite signal such as NTSC)
“NO SIGNAL”--- When No Signal
“101” [CR] -- When Input is PC series
“?” [CR]
Page
38
EXPAND SERIAL COMMAD FUNCTIONAL SPECIFICATION for LV-5210/7215/7210
9.7 Input COMMAND
9.7.1
CR_INPUTCOMMAND
COMMAND
Details
“CR_INPUT” [CR]
Get selected. INPUT No.
Acceptable
Response
%a
Unacceptable
9.7.2
“COMPUTER1”.... COMPUTER1 Input is selected.
“COMPUTER2”.... COMPUTER2 Input is selected..
“VIDEO”.................... VIDEO Input is selected.
“?” [CR]
CR_SOURCECOMMAND
COMMAND
“CR_SOURCE” [CR]
Details
Get selected. Source
Acceptable
Response
%1
Unacceptable
9.7.3
“000_%a” [CR]
“000_%1” [CR]
“DIGITAL” ...... A DVI input is selected.
“ANALOG” ......ANALOG RGB is selected..
“SCART” ....…..SCART is selected..
“HDCP” ....……HDCP is selected..
“VIDEO” ....…..VIDEO input is selected..
“S-VIDEO” ......S-VIDEO is selected..
“YPBPR” ....…..YPBPR input is selected..
“MCI”............... MCI Input is selected.
“WI”.................Wireless Imager Input is selected.
“NETWORK”.... Network Input is selected.
“Error code” [CR] ---- Invalid
“?” [CR] -------- When the projector received unclear command
CR_INPUT_%1COMMAND
COMMAND
%1
Details
“CR_INPUT_%1” [CR]
“COMPUTER1”.... Specify COMPUTER 1 input
“COMPUTER2”.... Specify COMPUTER 2 input
“VIDEO”................ Specify VIDEO input
Get specified input source
Acceptable
Response
%a
Unacceptable
“000_%a” [CR]
When %1 is COMPUTER1…
“ANALOG”........ ANALOG RGB is selected
“DEGITAL”.... DVI mode
“HDCP”................ HDCPmode
When %1 is COMPUTER2…
“ANALOG”........ ANALOG RGB mode
“YPBPR”............ Component mode
“SCART”............ SCART mode
“OUT”.................... MONITOR OUT mode
When %1 is VIDEO…
“AUTO”................ VIDEO AUTO is selected
“VIDEO”............ Composite VIDEO input is selected.
“S-VIDEO”.... S-VIDEO input is selected
“?” [CR]
Page
39
EXPAND SERIAL COMMAD FUNCTIONAL SPECIFICATION for LV-5210/7215/7210
9.7.4
CR_SYSTEMCOMMAND
COMMAND
“CR_SYSTEM” [CR]
Details
Get selected. system
Acceptable
“000_%1” [CR]
INPUT IS
PC
%1
INPUT IS VIDEL
Response
Unacceptable
“MODE1”
“MODE2”
“MODE3”
“MODE4”
“MODE5”
“AUTO” .............. AUTO is selected.
“NTSC” .............. NTSC is selected.
“NNTSC443”.... NTSC4.43 is selected.
“PAL” .................. PAL is selected.
“SECAM” .......... SECAM is selected.
“PAL-M” .......... PAL-M is selected.
“PAL-N” .......... PAL-N is selected.
“1080I”............ 1080i is selected.
“1035I” .......... 1035i is selected.
“720P” .............. 720p is selected.
“575P” .............. 575p is selected.
“480P” .............. 480p is selected.
“575I” .............. 575i is selected.
“480I” .............. 480i is selected.
“101” [CR] .... When Input is PC
“?” [CR] ........................ When received command is unclear
9.8 Screen COMMAND
9.8.1
CR_SCREENCOMMAND
COMMAND
Details
“CR_SCREEN” [CR]
Get selected Screen Size
Acceptable
“000_%a” [CR]
Input is PC
%a
Input
VIDEO
Response
“NORMAL”.... Select 4:3 screen
“WIDE”............ Select 16:9 screen
“TRUE”............ True Size
“NORMAL”.... Select 4:3 Screen
“WIDE”............ Select 16:9 screen
is
Unacceptable
“Error Code” [CR] .... Invalid
“?” [CR] ........................ COMMAND
Page
40
EXPAND SERIAL COMMAD FUNCTIONAL SPECIFICATION for LV-5210/7215/7210
9.8.2
CR_FLSCRENCOMMAND
COMMAND
Details
“CR_FLSCREN” [CR]
Get the screen size status that Full Screen is selected. or not.
Acceptable
%a
Response
Unacceptable
9.8.3
“ON”=Full Screen is set.
“OFF”=Full Screen is not set.
“Error code” [CR] ---- Invalid
“?” [CR] -------- When the projector received unclear command
CR_TRUECOMMAND
COMMAND
Details
“CR_TRUE” [CR]
Get information if the screen setting is True or not.
Acceptable
%a
Response
Unacceptable
9.8.4
“000_%1” [CR]
“000_%1” [CR]
“ON”.......... True is set.
“OFF”...... True is not set.
“Error code” [CR] ---- Invalid
“?” [CR] -------- When the projector received unclear command
CR_ KYSTNMODECOMMAND
COMMAND
Details
“CR_KYSTNMODE” [CR]
Get Keystone Store MODE setting status
Acceptable
Response
%a
Unacceptable
“000_%a” [CR]
“STR”-- “Store MODE” is Store
“RST”-- “Store MODE” is Reset
“?” [CR]
........................ COMMAND
9.9 Lamp COMMAND
9.9.1
CR_LAMPREPLCOMMAND
COMMAND
Details
“CR_LAMPREPL” [CR]
Get lamp replacement time information
Acceptable
Response
%1
Unacceptable
“000_%1” [CR]
“1Y”-- over the lamp replacement time
“1N”-- have not reached the lamp replacement time
“?” [CR]
Page
41
EXPAND SERIAL COMMAD FUNCTIONAL SPECIFICATION for LV-5210/7215/7210
9.9.2
CR_LAMPMODECOMMAND
COMMAND
Details
“CR_LAMPHMODE” [CR]
Get lamp replacement time information
Acceptable
Response
%1
Unacceptable
9.9.3
“000_%1” [CR]
“NORMAL” Lamp MODE is NORMAL
“ECO”Lamp MODE is silent
“AUTO” Lamp MODE is AUTO
“?” [CR]
CR_PROJHCOMMAND
COMMAND
Details
“CR_PROJH” [CR]
Get total projector running time. (h= hours)
Acceptable
Response
%1
“000_%1” [CR]
“0000000”-- ”9999999”
Unacceptable
9.10
?” [CR]
Sound Status COMMAND
9.10.1 CR_VOLUMECOMMAND
COMMAND
Details
“CR_VOLUME” [CR]
Get User Control Volume
Acceptable
Response
%a
Unacceptable
“000_%a” [CR]
“000”-- ”063”
“?” [CR]
9.10.2 CR_MUTECOMMAND
COMMAND
Details
“CR_MUTE” [CR]
Get sound mute setting value
Acceptable
Response
%a
Unacceptable
“000_%a” [CR]
“ON”---- Sound mute is ON
“OFF”-- Sound mute is OFF
“?” [CR]
Page
42
EXPAND SERIAL COMMAD FUNCTIONAL SPECIFICATION for LV-5210/7215/7210
9.11
Setting Status COMMAND
9.11.1 CR_BBACKCOMMAND
COMMAND
Details
“CR_BBACK” [CR]
Get Blue Back setting value
Acceptable
Response
%a
Unacceptable
“000_%a” [CR]
“ON”----- Set Blue Back
“OFF”--- Cancel Blue Back
“?” [CR]
9.11.2 CR_DISPCOMMAND
COMMAND
Details
“CR_DISP” [CR]
Get Display setting status
Acceptable
Response
%a
Unacceptable
“000_%a” [CR]
“ON”----- Set Display
“OFF”--- Cancel Display
“?” [CR]
9.11.3 CR_LOGOCOMMAND
COMMAND
Details
“CR_LOGO” [CR]
Get Logo setting status
Acceptable
Response
%1
Unacceptable
“000_%1” [CR]
“OFF”....................Cancel Logo Function
“DEFAULT”.... Logo Function Default
“USER”................ Logo Function User
“?” [CR]
9.11.4 CR_RCODECOMMAND
COMMAND
Details
“CR_RCCODE” [CR]
Get the selected. code in Remote Control MODE
Acceptable
Response
“000_%a” [CR]
%a
“001”=
“002”=
“003”=
“004”=
“005”=
“006”=
“007”=
“008”=
Unacceptable
“?” [CR]
Code 1 is selected.
Code 2 is selected.
Code 3 is selected.
Code 4 is selected.
Code 5 is selected.
Code 6 is selected.
Code 7 is selected.
Code 8 is selected.
Page
43
EXPAND SERIAL COMMAD FUNCTIONAL SPECIFICATION for LV-5210/7215/7210
9.11.5 CR_LANGCOMMAND
COMMAND
Details
“CR_LANG” [CR]
Get selected. language
Acceptable
Response
%a
“000_%a” [CR]
“ENG”---- English is selected.
“DEU”---- German is selected.
“FRA”---- French is selected.
“ITA”---- Italian is selected.
“ESP”---- Spanish is selected.
“POR”---- Portuguese is selected.
“NED”---- Dutch is selected.
“SVE”---- Swedish is selected.
“JPN”---- Japanese is selected.
“CHI”---- Korean is selected.
“KOR”---- Chinese is selected.
“RUS”---- Russian is selected.
Unacceptable
“?” [CR]
9.11.6 CR_ON-STACOMMAND
COMMAND
Details
“CR_ON-STA” [CR]
Get selected Power on start
Acceptable
Response
%a
Unacceptable
“000_%a” [CR]
“ON”=Set Power ON Start
“OFF”=Cancel Power ON Start
“?” [CR]
9.11.7 CR_P-MANECOMMAND
COMMAND
Details
“CR_P-MANE” [CR]
Get the time to start Power management
Acceptable
Response
%a
Unacceptable
“000_%a” [CR]
“OFF”------------ Power management is Canceled
“READY”-------- Power management is Ready
“SHUTDOWN”-- Power management is set to Shut Down
MODE
“?” [CR]
9.11.8 CR_P-MANETIMECOMMAND
COMMAND
Details
“CR_P-MAETIME” [CR]
Get the time to start Power management
Acceptable
Response
%a
Unacceptable
“000_%a” [CR]
“001”-”030”-- 1mininute to 30 minutes
“?” [CR]
Page
44
EXPAND SERIAL COMMAD FUNCTIONAL SPECIFICATION for LV-5210/7215/7210
9.11.9 CR_FANSPEEDCOMMAND
COMMAND
“CR_FANSPEED” [CR]
Details
Get Fan Control Speed
Acceptable
Response
%a
Unacceptable
“000_%a” [CR]
“MAX”--- Fan Control Speed is Max.
“NOR”--- Fan Control Speed is NORMAL
“?” [CR]
9.11.10 CR_KEYDISCOMMAND
COMMAND
“CR_KEYDIS” [CR]
Details
Get RC//KEY status
Acceptable
Response
%a
Unacceptable
“000_%a” [CR]
“N/A”=Both RC & KEY are available.
“RC”=RC is locked
“KEY”=KEY is locked
“?” [CR]
9.11.11 CR_TERMINALCOMMAND
COMMAND
Details
“CR_TERMINAL” [CR]
Get Terminal Setting status
Acceptable
Response
%a
Unacceptable
“000_%a” [CR]
“COMPUTER”.... COMPUTER input mode
“MONITOR”........ MONITOR Out mode
“?” [CR]
9.11.12 CR_STANDBYMODECOMMAND
COMMAND
Details
“CR_STANDBYMODE” [CR]
Get the setting status for Stand By Mode
Acceptable
Response
%a
Unacceptable
“000_%a” [CR]
“ECO”.................... Eco Mode
“NORMAL”........ Normal Mode
“?” [CR]
Page
45
EXPAND SERIAL COMMAD FUNCTIONAL SPECIFICATION for LV-5210/7215/7210
9.11.13 CR_POINTERCOMMAND
COMMAND
Details
“CR_POINTER” [CR]
Get pointer setting status
Acceptable
%a
“SPOTLIGHT”..….. Spotlight Mode
“ARROW”................ Arrow Mode
“FINGER”................ Finger Mode
“LASER”.................. Laser Mark Mode
%b
When SPOTLIGHT…
“MAX”......................Maximum
“MID”...................... Middle
“MIN”...................... Minimum
When ARROW/FINGER/LASER…
N/A
Response
Unacceptable
9.12
“000_%a_%b” [CR]
“?” [CR]
Other Status Read COMMAND
9.12.1 CR_SIGNALCOMMAND
COMMAND
Details
“CR_SIGNAL” [CR]
Get information if there is signal or not
Acceptable
Response
%a
“000_%a” [CR]
“ON”= There is signal
“OFF”=No signal
Unacceptable
?” [CR]
9.12.2 CR_VMUTECOMMAND
COMMAND
Details
“CR_VMUTE” [CR]
Get No Show setting status
Acceptable
Response
%a
Unacceptable
“000_%a” [CR]
“ON”----- Set No Show
“OFF”--- Cancel No Show
“?” [CR]
9.12.3 CR_FREEZECOMMAND
COMMAND
Details
“CR_FREEZE” [CR]
Get Freeze setting status
Acceptable
Response
%a
Unacceptable
“000_%a” [CR]
“ON”----- Set No Show
“OFF”--- Cancel No Show
“?” [CR]
Page
46
EXPAND SERIAL COMMAD FUNCTIONAL SPECIFICATION for LV-5210/7215/7210
9.12.4 CR_PTIMERCOMMAND
COMMAND
Details
“CR_PTIMER” [CR]
Get Presentation Timer status
Acceptable
Response
%a
Unacceptable
“000_%a” [CR]
“ON”------- Presentation timer is active
“STOP”--- Presentation timer is pause
“OFF”----- Presentation timer is inactive
“?” [CR]
9.12.5 CR_TEMPWARNCOMMAND
COMMAND
Details
“CR_TEMPWARN” [CR]
Get if the sensors are exceeding or approaching critical temperature. When
some sensors are installed inside the projector, get each sensor’s
temperature.
Acceptable
Response
%a
%b
%c
Unacceptable
“000_%a_%b_%c” [CR]
%a…temperature sensor 1 status
%b…temperature sensor 2 status
%c…temperature sensor 3 status
“W”--- Exceeding critical temperature(Warning)
“S”--- Sensor temperature is safe.
“N”--- Not relate to the temperature
Ex. When “S_W_S”[CR] means that sensor 1 is safety
temperature, sensor 2 is exceeding critical temperature,
and sensor 3 is safety temperature.
Note)Depends on projector Models, when the temperature
difference between sensor 1 and sensor 2 is over the specified
temperature, the sensor may show “W”. In this case, sensor
3 shows that the temperature difference is “W”, “S”, or “N”.
“?” [CR]
9.12.6 CR_TEMPFAILCOMMAND
COMMAND
Details
“CR_TEMPFAIL” [CR]
Get the temperature inside a projector.
When some temperature sensors are installed in the projector, it is possible
to know the temperature all at once.
Acceptable
Response
%a
%b
%c
Unacceptable
“000_%a_%b_%c” [CR]
%a=Temperature, sensor 1
%b=Temperature, sensor 2
%c=Temperature, sensor 3
(Ex.) “_31.5F” [CR]
_means a space. When the temperature sinks to -, the first
character “-”like “-05.5F” [CR].
Last character indicates the sensor’s status.
Exceeding critical temperature =”F”
Sensor temperature is safe
=”S”
Not relate to the temperature=”N”
“_31.5F”indicates 31.5 degrees and safety temperature.
When the temperature is safe, the data will be “ 00.0S”.
Every time the projector is reset, “ 00.0S”is set.
In short, previous data is deleted.
“?” [CR]
Page
47