DeWalt DCD945 Technical data

www.
.eu
DCD920
DCD925
DCD930
DCD935
DCD940
DCD945
Copyright DEWALT
2
Figure 1
d
f
e
g
c
b
a
i
DCD920
h
d
e
f
g
c
b
a
i
DCD925
1
Figure 2
k
j
l
Figure 3
B
A
Figure 5
Figure 4
2
Figure 6
e
e
f
f
g
g
Figure 7
Figure 8
Figure 9
Figure 11
Figure 12
d
Figure 10
m
Figure 13
h
i
3
EN GLI S H
1/2" (13 mm) CORDLESS DRILL/DRIVER
DCD920, DCD930, DCD940
1/2" (13 mm) CORDLESS HAMMERDRILL/DRIVER
DCD925, DCD935, DCD945
Congratulations!
You have chosen a DEWALT tool. Years of experience, thorough product development and innovation make
DEWALT one of the most reliable partners for professional power tool users.
Technical Data
Voltage
Type
Battery Type
Power output
No-load speed
1st gear
2nd gear
3rd gear
Impact rate
1st gear
2nd gear
3rd gear
Max. torque
Chuck capacity
Maximum drilling capacity
Wood
Metal
Masonry
Weight (without battery pack)
LPA
KPA
LWA
KWA
(sound pressure)
(sound pressure uncertainty)
(sound power)
(sound power uncertainty)
W
DCD925
18
10
NiMH/Li-Ion
450
min-1
min-1
min-1
0–500
0–1,250
0–2,000
0–500
0–1,250
0–2,000
0–425
0–1,200
0–1,800
0–425
0–1,200
0–1,800
0–425
0–1,200
0–1,800
0–425
0–1,200
0–1,800
min-1
min-1
min-1
Nm
mm
0–8,500
0–21,250
0–34,000
55
1.5–13
–
–
–
55
1.5–13
0–7,225
0–20,400
0–30,600
50
1.5–13
–
–
–
50
1.5–13
0–7,225
0–20,400
0–30,600
44
1.5–13
–
–
–
44
1.5–13
mm
mm
mm
kg
50
13
16
1.82
50
13
16
1.7
45
13
14
1.79
45
13
14
1.68
38
13
13
1.79
38
13
13
1.68
dB(A)
dB(A)
dB(A)
dB(A)
88
3
99
3
77
3
88
3
88
3
99
3
77
3
88
3
88
3
99
3
77
3
88
3
< 2.5
1.5
< 2.5
1.5
< 2.5
1.5
< 2.5
1.5
10.5
1.8
–
–
10.5
1.8
–
–
VDC
DCD920 DCD935 DCD930 DCD945
18
14.4
14.4
12
10
10
10
10
NiMH/Li-Ion NiMH/Li-Ion NiMH/Li-Ion
NiMH
450
325
325
285
Vibration total values (triax vector sum) determined according to EN 60745:
Vibration emission value ah
Drilling into metal
ah,D =
m/s²
< 2.5
< 2.5
Uncertainty K =
m/s²
1.5
1.5
Vibration emission value ah
Impact drilling
ah,ID =
m/s²
10.5
–
Uncertainty K =
m/s²
1.8
–
4
DCD940
12
10
NiMH
285
ENGLISH
Vibration emission value ah
Screwdriving
ah,D =
Uncertainty K =
m/s²
m/s²
< 2.5
1.5
< 2.5
1.5
WARNING: The declared vibration
emission level represents the main
applications of the tool. However if the
tool is used for different applications,
with different accessories or poorly
maintained, the vibration emission may
differ. This may significantly increase the
exposure level over the total working
period.
VDC
Ah
kg
Charger
Mains voltage
Battery type
Approx. charging time
min
Weight
kg
Fuses:
Europe
U.K. & Ireland
VAC
230 V tools
230 V tools
DE9180
Li-Ion
18
2.0
0.68
DE9135
230
NiCd/NiMH/Li-Ion
40
(2.0 Ah battery packs)
0.52
10 Amperes, mains
3 Amperes, in plugs
Definitions: Safety Guidelines
The definitions below describe the level of severity
for each signal word. Please read the manual and
pay attention to these symbols.
DANGER: Indicates an imminently
hazardous situation which, if not avoided,
will result in death or serious injury.
WARNING: Indicates a potentially
hazardous situation which, if not
avoided, could result in death or
serious injury.
CAUTION: Indicates a potentially
hazardous situation which, if not
avoided, may result in minor or
moderate injury.
< 2.5
1.5
< 2.5
1.5
< 2.5
1.5
An estimation of the level of exposure to
vibration should also take into account
the times when the tool is switched off
or when it is running but not actually
doing the job. This may significantly
reduce the exposure level over the total
working period.
The vibration emission level given in this information
sheet has been measured in accordance with a
standardised test given in EN 60745 and may be
used to compare one tool with another. It may be
used for a preliminary assessment of exposure.
Battery pack
Battery type
Voltage
Capacity
Weight
< 2.5
1.5
Identify additional safety measures to
protect the operator from the effects of
vibration such as: maintain the tool and
the accessories, keep the hands warm,
organisation of work patterns.
DE9503
NiMH
18
2.6
1.0
DE9140
Li-Ion
14.4
2.0
0.58
DE9502
NiMH
14.4
2.6
0.86
DE9501
NiMH
12
2.6
0.69
DE9116
230
NiCd/NiMH
60
(2.0 Ah battery packs)
0.4
NOTICE: Indicates a practice not
related to personal injury which, if
not avoided, may result in property
damage.
Denotes risk of electric shock.
Denotes risk of fire.
EC-Declaration of Conformity
MACHINERY DIRECTIVE
DCD925, DCD920, DCD935, DCD930, DCD945, DCD940
DEWALT declares that these products described
under “technical data” are in compliance with:
98/37/EC (until Dec. 28, 2009), 2004/108/EC,
5
EN GLI S H
2006/42/EC (from Dec. 29, 2009), EN 60745-1,
EN 60745-2-1, EN 60745-2-2.
These products also comply with Directive
2004/108/EC. For more information, please contact
DEWALT at the following address or refer to the
back of the manual.
b)
The undersigned is responsible for compilation of the
technical file and makes this declaration on behalf of
DEWALT.
c)
d)
Horst Grossmann
Vice President Engineering and Product
Development
DEWALT, Richard-Klinger-Straße 11,
D-65510, Idstein, Germany
30.07.2009
WARNING: To reduce the risk of injury,
read the instruction manual.
General Power Tool Safety Warnings
WARNING! Read all safety warnings
and all instructions. Failure to follow
the warnings and instructions may result
in electric shock, fire and/or serious
injury.
SAVE ALL WARNINGS AND INSTRUCTIONS
FOR FUTURE REFERENCE
The term “power tool” in the warnings refers to your
mains-operated (corded) power tool or batteryoperated (cordless) power tool.
1) WORK AREA SAFETY
a) Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power
tools create sparks which may ignite the dust
or fumes.
c) Keep children and bystanders away while
operating a power tool. Distractions can
cause you to lose control.
2) ELECTRICAL SAFETY
a) Power tool plugs must match the outlet.
Never modify the plug in any way. Do
not use any adapter plugs with earthed
(grounded) power tools. Unmodified plugs
6
e)
f)
and matching outlets will reduce risk of
electric shock.
Avoid body contact with earthed or
grounded surfaces such as pipes,
radiators, ranges and refrigerators. There
is an increased risk of electric shock if your
body is earthed or grounded.
Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
Do not abuse the cord. Never use the
cord for carrying, pulling or unplugging
the power tool. Keep cord away from
heat, oil, sharp edges or moving parts.
Damaged or entangled cords increase the
risk of electric shock.
When operating a power tool outdoors,
use an extension cord suitable for outdoor
use. Use of a cord suitable for outdoor use
reduces the risk of electric shock.
If operating a power tool in a damp
location is unavoidable, use a residual
current device (RCD) protected supply.
Use of an RCD reduces the risk of electric
shock.
3) PERSONAL SAFETY
a) Stay alert, watch what you are doing and
use common sense when operating a
power tool. Do not use a power tool while
you are tired or under the influence of
drugs, alcohol or medication. A moment of
inattention while operating power tools may
result in serious personal injury.
b) Use personal protective equipment.
Always wear eye protection. Protective
equipment such as dust mask, non-skid
safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce
personal injuries.
c) Prevent unintentional starting. Ensure
the switch is in the off position before
connecting to power source and/or
battery pack, picking up or carrying the
tool. Carrying power tools with your finger
on the switch or energising power tools that
have the switch on invites accidents.
d) Remove any adjusting key or wrench
before turning the power tool on. A
wrench or a key left attached to a rotating
part of the power tool may result in personal
injury.
e) Do not overreach. Keep proper
footing and balance at all times. This
enables better control of the power tool in
unexpected situations.
ENGLISH
f)
g)
Dress properly. Do not wear loose
clothing or jewellery. Keep your hair,
clothing and gloves away from moving
parts. Loose clothes, jewellery or long hair
can be caught in moving parts.
If devices are provided for the connection
of dust extraction and collection facilities,
ensure these are connected and properly
used. Use of dust collection can reduce
dust-related hazards.
4) POWER TOOL USE AND CARE
a) Do not force the power tool. Use the
correct power tool for your application.
The correct power tool will do the job
better and safer at the rate for which it
was designed.
b) Do not use the power tool if the switch
does not turn it on and off. Any power
tool that cannot be controlled with the switch
is dangerous and must be repaired.
c) Disconnect the plug from the power
source and/or the battery pack from
the power tool before making any
adjustments, changing accessories, or
storing power tools. Such preventive safety
measures reduce the risk of starting the
power tool accidentally.
d) Store idle power tools out of the reach
of children and do not allow persons
unfamiliar with the power tool or these
instructions to operate the power tool.
Power tools are dangerous in the hands of
untrained users.
e) Maintain power tools. Check for
misalignment or binding of moving parts,
breakage of parts and any other condition
that may affect the power tool’s operation.
If damaged, have the power tool repaired
before use. Many accidents are caused by
poorly maintained power tools.
f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp
cutting edges are less likely to bind and are
easier to control.
g) Use the power tool, accessories and
tool bits etc., in accordance with these
instructions taking into account the
working conditions and the work to
be performed. Use of the power tool for
operations different from those intended
could result in a hazardous situation.
5) BATTERY TOOL USE AND CARE
a) Recharge only with the charger specified
by the manufacturer. A charger that is
suitable for one type of battery pack may
b)
c)
d)
create a risk of fire when used with another
battery pack.
Use power tools only with specifically
designated battery packs. Use of any
other battery packs may create a risk of
injury and fire.
When battery pack is not in use, keep it
away from other metal objects like paper
clips, coins, keys, nails, screws or other
small metal objects that can make a
connection from one terminal to another.
Shorting the battery terminals together may
cause burns or a fire.
Under abusive conditions, liquid may be
ejected from the battery, avoid contact.
If contact accidentally occurs, flush with
water. If liquid contacts eyes, additionally
seek medical help. Liquid ejected from the
battery may cause irritation or burns.
6) SERVICE
a) Have your power tool serviced by a
qualified repair person using only identical
replacement parts. This will ensure that the
safety of the power tool is maintained.
Additional Specific Safety Rules for
Drills/Drivers/Hammerdrills
• Wear ear protectors when impact drilling.
Exposure to noise can cause hearing loss.
• Use auxiliary handles, if supplied with the
tool. Loss of control can cause personal injury.
• Hold power tools by insulated gripping
surfaces when performing an operation
where the cutting tool may contact hidden
wiring or its own cord. Cutting accessory
contacting a “live” wire may make exposed
metal parts of the power tool “live” and could
give the operator an electric shock.
• Use clamps or other practical way to secure
and support the workpiece to a stable
platform. Holding the work by hand or against
your body is unstable and may lead to loss of
control.
• Wear ear protectors when hammering
for extended periods of time. Prolonged
exposure to high intensity noise can cause
hearing loss. Temporary hearing loss or serious
ear drum damage may result from high sound
levels generated by hammerdrilling.
• Wear safety goggles or other eye protection.
Hammering and drilling operations cause chips
to fly. Flying particles can cause permanent eye
damage.
7
EN GLI S H
• Hammer bits and tools get hot during
operation. Wear gloves when touching them.
Residual Risks
The following risks are inherent to the use of
percussion drills:
– Injuries caused by touching the rotating parts or
hot parts of the tool.
In spite of the application of the relevant safety
regulations and the implementation of safety
devices, certain residual risks cannot be avoided.
These are:
– Impairment of hearing.
– Risk of squeezing fingers when changing
accessories.
– Health hazards caused by breathing dust
developed when working in wood.
– Risk of personal injury due to flying particles.
– Risk of personal injury due to prolonged use.
Markings on Tool
The following pictograms are shown on the tool:
Read instruction manual before use.
CAUTION: Burn hazard. To reduce
the risk of injury, charge only DEWALT
rechargeable batteries. Other types of
batteries may burst causing personal
injury and damage.
CAUTION: Under certain conditions,
with the charger plugged in to the
power supply, the exposed charging
contacts inside the charger can be
shorted by foreign material. Foreign
materials of a conductive nature such
as, but not limited to, steel wool,
aluminum foil, or any buildup of metallic
particles should be kept away from
charger cavities. Always unplug the
charger from the power supply when
there is no battery pack in the cavity.
Unplug charger before attempting to
clean.
• DO NOT attempt to charge the battery pack
with any chargers other than the ones in
this manual. The charger and battery pack are
specifically designed to work together.
• These chargers are not intended for
any uses other than charging DEWALT
rechargeable batteries. Any other uses
may result in risk of fire, electric shock or
electrocution.
DATE CODE POSITION
• Do not expose charger to rain or snow.
The Date Code, which also includes the year of
manufacture, is printed into the housing surface that
forms the mounting joint between tool and battery.
• Pull by plug rather than cord when
disconnecting charger. This will reduce risk
of damage to electric plug and cord.
Example:
• Make sure that cord is located so that it
will not be stepped on, tripped over, or
otherwise subjected to damage or stress.
2009 XX XX
Year of Manufacture
Important Safety Instructions for All
Battery Chargers
SAVE THESE INSTRUCTIONS: This manual
contains important safety and operating instructions
for the DE9135/DE9116 battery chargers.
• Before using charger, read all instructions and
cautionary markings on charger, battery pack,
and product using battery pack.
DANGER: Electrocution hazard.
230 volts are present at charging
terminals. Do not probe with conductive
objects. Electric shock or electrocution
may result.
WARNING: Shock hazard. Do not allow
any liquid to get inside charger. Electric
shock may result.
8
• Do not use an extension cord unless it
is absolutely necessary. Use of improper
extension cord could result in risk of fire,
electric shock, or electrocution.
• Do not place any object on top of charger
or place the charger on a soft surface that
might block the ventilation slots and result
in excessive internal heat. Place the charger
in a position away from any heat source. The
charger is ventilated through slots in the top and
the bottom of the housing.
• Do not operate charger with damaged cord
or plug — have them replaced immediately.
• Do not operate charger if it has received
a sharp blow, been dropped, or otherwise
damaged in any way. Take it to an authorized
service center.
ENGLISH
• Do not disassemble charger; take it to an
authorized service center when service or
repair is required. Incorrect reassembly may
result in a risk of electric shock, electrocution or
fire.
• Disconnect the charger from the outlet
before attempting any cleaning. This will
reduce the risk of electric shock. Removing
the battery pack will not reduce this risk.
• NEVER attempt to connect 2 chargers together.
• The charger is designed to operate on
standard 230V household electrical power.
Do not attempt to use it on any other
voltage. This does not apply to the vehicular
charger.
SAVE THESE INSTRUCTIONS
Chargers
The DE9116 charger accepts 7.2–18 V NiCd and
NiMH batteries.
The DE9135 charger accepts 7.2–18 V NiCd, NiMH
or Li-Ion batteries.
These chargers require no adjustment and are
designed to be as easy as possible to operate.
Charging Procedure (fig. 1)
DANGER: Electrocution hazard.
230 volts present at charging terminals.
Do not probe with conductive objects.
Danger of electric shock or
electrocution.
1. Plug the charger (l) into an appropriate outlet
before inserting battery pack.
2. Insert the battery pack into the charger. The red
(charging) light will blink continuously indicating
that the charging process has started.
3. The completion of charge will be indicated by
the red light remaining ON continuously. The
pack is fully charged and may be used at this
time or left in the charger.
NOTE: To ensure maximum performance and life of
NiCd, NiMH and Li-Ion batteries, charge the battery
for a minimum of 10 hours before first use.
Charging Process
Refer the table below for the state of charge of the
battery pack.
State of charge
charging
fully charged
hot/cold pack delay
replace battery pack
problem
– – – –
–––––––––––
–– – –– –
•••••••••••
•• •• •• ••
Automatic Refresh
The automatic refresh mode will equalise or balance
the individual cells in the battery pack at its peak
capacity. Battery packs should be refreshed weekly
or whenever the pack no longer delivers the same
amount of work.
To refresh your battery pack, place the battery in the
charger as usual. Leave the battery pack for at least
10 hours in the charger.
Hot/Cold Pack Delay
When the charger detects a battery that is too hot
or too cold, it automatically starts a Hot/Cold Pack
Delay, suspending charging until the battery has
reached an appropriate temperature. The charger
then automatically switches to the pack charging
mode. This feature ensures maximum battery life.
LI-ION BATTERY PACKS ONLY
Li-Ion batteries are designed with an Electronic
Protection System that will protect the battery
against overloading, overheating or deep discharge.
The tool will automatically turn off if the Electronic
Protection System engages. If this occurs, place the
Li-Ion battery on the charger until it is fully charged.
Important Safety Instructions for All
Battery Packs
When ordering replacement battery packs, be sure
to include catalog number and voltage.
The battery pack is not fully charged out of the
carton. Before using the battery pack and charger,
read the safety instructions below. Then follow
charging procedures outlined.
READ ALL INSTRUCTIONS
• Do not charge or use battery in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Inserting
or removing the battery from the charger may
ignite the dust or fumes.
• Charge the battery packs only in DEWALT
chargers.
• DO NOT splash or immerse in water or other
liquids.
9
EN GLI S H
• Do not store or use the tool and battery
pack in locations where the temperature
may reach or exceed 40˚ C (105° F) (such as
outside sheds or metal buildings in summer).
DANGER: Never attempt to open the
battery pack for any reason. If battery
pack case is cracked or damaged,
do not insert into charger. Do not
crush, drop or damage battery pack.
Do not use a battery pack or charger
that has received a sharp blow, been
dropped, run over or damaged in any
way (i.e., pierced with a nail, hit with a
hammer, stepped on). Electric shock
or electrocution may result. Damaged
battery packs should be returned to
service center
for recycling.
CAUTION: When not in use, place
tool on its side on a stable surface
where it will not cause a tripping or
falling hazard. Some tools with large
battery packs will stand upright on the
battery pack but may be easily knocked
over.
SPECIFIC SAFETY INSTRUCTIONS FOR NICKEL CADMIUM
(NiCd) OR NICKEL METAL HYDRIDE (NiMH)
• Do not incinerate the battery pack even if it
is severely damaged or is completely worn
out. The battery pack can explode in a fire.
• A small leakage of liquid from the battery
pack cells may occur under extreme usage
or temperature conditions. This does not
indicate a failure.
However, if the outer seal is broken:
a. and the battery liquid gets on your skin,
immediately wash with soap and water for
several minutes.
b. and the battery liquid gets into your eyes,
flush them with clean water for a minimum
of 10 minutes and seek immediate medical
attention. (Medical note: The liquid is
25–35% solution of potassium hydroxide.)
SPECIFIC SAFETY INSTRUCTIONS FOR LITHIUM ION
(Li-Ion)
• Do not incinerate the battery pack even if it
is severely damaged or is completely worn
out. The battery pack can explode in a fire.
Toxic fumes and materials are created when
lithium ion battery packs are burned.
• If battery contents come into contact with
the skin, immediately wash area with mild
soap and water. If battery liquid gets into the
10
eye, rinse water over the open eye for
15 minutes or until irritation ceases. If medical
attention is needed, the battery electrolyte
is composed of a mixture of liquid organic
carbonates and lithium salts.
• Contents of opened battery cells may cause
respiratory irritation. Provide fresh air. If
symptoms persists, seek medical attention.
WARNING: Burn hazard. Battery liquid
may be flammable if exposed to spark
or flame.
Battery Cap (fig. 3)
A protective battery cap is supplied to cover the
contacts of a detached battery pack. Without the
protective cap in place, loose metal objects could
short circuit the contacts, causing a fire hazard and
damaging the battery pack.
1. Take off the protective battery cap before
placing the battery pack in the charger
or tool (fig. 3A).
2. Place the protective cap over the contacts
immediately after removing the battery pack
from the charger or tool (fig. 3B).
WARNING: Make sure the protective
battery cap is in place before storing or
carrying a detached battery pack.
Battery Pack
BATTERY TYPE
The DCD925 and DCD920 operate on 18 volt
battery packs.
The DCD935 and DCD930 operate on 14,4 volt
battery packs.
The DCD945 and DCD940 operate on 12 volt battery
pack
Storage Recommendations
1. The best storage place is one that is cool and
dry away from direct sunlight and excess heat
or cold. For optimum battery performance and
life, store battery packs at room temperature
when not in use.
NOTE: Li-Ion battery packs should be fully
charged when stored.
2. Long storage will not harm the battery pack or
charger. Under proper conditions, they can be
stored for up to 5 years.
ENGLISH
Labels on Charger and Battery Pack
Package Contents
In addition to the pictographs used in this manual,
the labels on the charger and the battery pack show
the following pictographs:
The package contains:
Read instruction manual
before use.
1 cordless percussion drill
(DCD945, DCD935, DCD925 models)
1 cordless midhandle drill driver
(DCD940, DCD930, DCD920 models)
1 Li-Ion battery pack (L1 models)
Battery charging.
2 Li-Ion battery packs (L2 models)
2 NiMH battery packs (B2 models)
Battery charged.
3 NiMH battery packs (B3 models)
1 Kitbox
Battery defective.
1 Charger
1 Side handle
Hot/cold pack delay.
Do not probe with conductive objects.
Do not charge damaged battery packs.
Use only with DEWALT battery packs,
others may burst, causing personal injury
and damage.
Do not expose to water.
1 Instruction manual
1 Exploded drawing
NOTE: Battery packs and chargers are not included
with N-models.
• Check for damage to the tool, parts or
accessories which may have occurred during
transport.
• Take the time to thoroughly read and
understand this manual prior to operation.
Description (fig. 1, 2)
WARNING: Never modify the power
tool or any part of it. Damage or
personal injury could result.
Have defective cords replaced
immediately.
a. Trigger switch
Charge only between 4 °C and 40 °C.
b. Forward/reverse button
Discard the battery pack with due care for
the environment.
d. Chuck
c. LED light
e. Torque adjustment collar
f. Mode control collar
Do not incinerate the battery pack
NiMH, NiCd+ and Li-Ion.
g. Gear shifter
h. Side handle
Charges NiMH and NiCd
battery packs.
i. Main handle
j. Battery pack
k. Battery release buttons
Charges Li-Ion battery packs.
See technical data for charging time.
l. Charger
INTENDED USE
These drills/drivers/hammerdrills are designed
for professional drilling, precussion drilling and
screwdriving applications.
11
EN GLI S H
DO NOT use under wet conditions or in presence of
flammable liquids or gases.
These drills/drivers/hammerdrills are professional
power tools.
DO NOT let children come into contact with the
tool. Supervision is required when inexperienced
operators use this tool.
Electrical Safety
The electric motor has been designed for one
voltage only. Always check that the battery pack
voltage corresponds to the voltage on the rating
plate. Also make sure that the voltage of your
charger corresponds to that of your mains.
Your DEWALT charger is double insulated
in accordance with EN 60335; therefore
no earth wire is required.
If the supply cord is damaged, it must be replaced
by a specially prepared cord available through the
DEWALT service organization.
Mains Plug Replacement
(U.K. & Ireland Only)
If a new mains plug needs to be fitted:
• Safely dispose of the old plug.
• Connect the brown lead to the live terminal in
the plug.
• Connect the blue lead to the neutral terminal.
WARNING: No connection is to be
made to the earth terminal.
Follow the fitting instructions supplied with good
quality plugs. Recommended fuse: 3 A.
Using an Extension Cable
An extension cord should not be used unless
absolutely necessary. Use an approved extension
cable suitable for the power input of your charger
(see technical data). The minimum conductor size is
1 mm2; the maximum length is 30 m.
When using a cable reel, always unwind the cable
completely.
ASSEMBLY AND ADJUSTMENTS
WARNING: Prior to assembly and
adjustment, always remove the battery
pack. Always switch off the tool before
inserting or removing the battery pack.
WARNING: Use only DEWALT battery
packs and chargers.
12
Inserting and Removing the
Battery Pack from the Tool (fig. 2)
WARNING: To reduce the risk of
serious personal injury, turn tool
off and disconnect battery pack
before making any adjustments or
removing/installing attachments or
accessories. An accidental start-up
can cause injury.
NOTE: Make sure your battery pack (j) is fully
charged.
TO INSTALL THE BATTERY PACK INTO THE TOOL HANDLE
1. Align the base of the tool with the notch inside
the tool’s handle (fig. 2).
2. Slide the battery pack firmly into the handle until
you hear the lock snap into place.
TO REMOVE THE BATTERY PACK FROM THE TOOL
1. Press the release buttons (k) and firmly pull the
battery pack out of the tool handle.
2. Insert battery pack into the charger as
described in the charger section of this manual.
Variable Speed Switch (fig. 1)
To turn the tool on, squeeze the trigger switch (a).
To turn the tool off, release the trigger switch. Your
tool is equipped with a brake. The chuck will stop as
soon as the trigger switch is fully released.
NOTE: Continuous use in variable speed range is
not recommended. It may damage the switch and
should be avoided.
Side Handle (fig. 1)
WARNING:To reduce the risk of
personal injury, ALWAYS operate
the tool with the side handle properly
installed. Failure to do so may result
in the side handle slipping during tool
operation and subsequent loss of
control. Hold tool with both hands to
maximize control.
The side handle (h) clamps to the front of the gear
case and may be rotated 360˚ to permit right- or
left-hand use. Side handle must be tightened
sufficiently to resist the twisting action of the tool if
the accessory binds or stalls. Be sure to grip the
side handle at the far end to control the tool
during a stall.
ENGLISH
If model is not equipped with side handle, grip drill
with one hand on the handle and one hand on the
battery pack.
NOTE: Side handle comes equipped on all models.
Forward/Reverse Control Button
(fig. 1)
NOTE: The torque adjustment collar may be
set to any number at any time. However, the
torque adjustment collar is only engaged during
screwdriving mode and not in drill and hammerdrill
modes.
HAMMERDRILLING (FIG. 6)
CAUTION: When the mode collar is in
the drill/hammerdrill mode, the drill will
not clutch out regardless of the position
of the torque adjustment collar (e).
A forward/reverse control button (b) determines the
direction of the tool and also serves as a lock off
button.
To select forward rotation, release the trigger switch
and depress the forward/reverse control button on
the right side of the tool.
To select reverse, release the trigger switch and
depress the forward/reverse control button on the
left side of the tool.
The center position of the control button locks the
tool in the off position. When changing the position
of the control button, be sure the trigger is released.
NOTE: The first time the tool is run after changing
the direction of rotation, you may hear a click on
start up. This is normal and does not indicate a
problem.
Worklight (fig. 1)
There is a worklight (c) located just above the trigger
switch (a). The worklight will be activated when the
trigger switch is squeezed.
NOTE: The worklight is for lighting the immediate
work surface and is not intended to be used as a
flashlight.
Mode Control Collar (fig. 4–6)
Your drill is equipped with a separate mode control
collar (f) to switch between drilling, screwdriving and
hammerdrilling mode.
DRILLING (FIG. 4)
CAUTION: When the mode collar is in
the drill/hammerdrill mode, the drill will
not clutch out regardless of the position
of the torque adjustment collar (e).
Rotate the mode control collar (f) so the drill symbol
is aligned with the arrow.
NOTE: The torque adjustment collar (e) may be set
on any number.
SCREWDRIVING (FIG. 5)
Rotate the mode control collar (f) so the screw
symbol is aligned with the arrow.
Rotate the mode control collar (f) so the hammer
symbol is aligned with the arrow.
Torque Adjustment Collar (fig. 4–6)
Your tool has an adjustable torque screwdriver
mechanism for driving and removing a wide array
of fastener shapes and sizes. Circling the torque
adjustment collar (e) are numbers. These numbers
are used to set the clutch to deliver a torque range.
The higher the number on the collar, the higher the
torque and the larger the fastener which can be
driven. To select any of the numbers, rotate until the
desired number aligns with the arrow.
Three-Speed Gearing (fig. 4–5)
The three-speed feature of your tool allows you to
shift gears for greater versatility. To select speed 1
(highest torque setting), turn the tool off and permit it
to stop. Slide the gear shifter (g) all the way forward.
Speed 2 (middle torque and speed setting) is in the
middle position. Speed 3 (highest speed setting) is
to the rear.
NOTE: Do not change gears when the tool is
running. Always allow the drill to come to a complete
stop before changing gears. If you have trouble
changing gears, make sure that the gear shifter is
engaged in one of the three speed settings.
Chucks
WARNING: Do not attempt to tighten
drill bits (or any other accessory) by
gripping the front part of the chuck
and turning the tool on. Damage to
the chuck and personal injury may
result. Always lock off trigger switch
and disconnect tool from power source
when changing accessories.
WARNING: Always ensure the bit is
secure before starting the tool. A loose
bit may eject from tool causing possible
personal injury.
13
EN GLI S H
KEYLESS SINGLE SLEEVE CHUCK (FIG. 7–9)
DCD940, DCD930, DCD920
Your tool features a keyless chuck with one rotating
sleeve for one-handed operation of the chuck. To
insert a drill bit or other accessory, follow these
steps.
1. Lock the trigger in the OFF position. Turn off
tool and disconnect tool from power source.
2. Grasp the black sleeve of the chuck (d) with
one hand and use the other hand to secure the
tool as shown in Figure 7. Rotate the sleeve
counterclockwise (as viewed from the front) far
enough to accept the desired accessory.
3. Insert the accessory about 3/4" (19 mm) into
the chuck and tighten securely by rotating the
chuck sleeve clockwise with one hand while
holding the tool with the other hand. Continue
to rotate the chuck sleeve until several ratchet
clicks are heard to ensure full gripping power.
To release the accessory, repeat Steps 1 and 2
above.
Be sure to tighten chuck with one hand on the
chuck sleeve and one hand holding the tool for
maximum tightness.
SELF-TIGHTENING CHUCK OPERATION (FIG. 10–12)
DCD945, DCD935, DCD925
To insert a drill bit or other accessory:
1. Lock the trigger in the OFF position. Turn off
tool and disconnect tool from power source.
2. Grasp the chuck sleeve (m) with one hand and
use the other hand to secure the tool as shown
in Figure 10. Rotate the sleeve counterclockwise
(as viewed from the front) far enough to accept
the desired bit or accessory.
3. Insert the bit or other accessory about 3/4"
(19 mm) into the chuck, as shown in Figure 11.
Grasp the chuck sleeve (m) securely and rotate
the sleeve clockwise (viewed from the front) with
one hand while using the other hand to secure
the tool. Rotate the sleeve clockwise until sleeve
cannot be rotated any further, as demonstrated
in Figure 12. As the drill is being operated in
the forward position, the chuck will continually
self tighten the jaws of the chuck onto the bit or
accessory to maximize the bit gripping strength.
WARNING: To reduce the risk
of serious personal injury, turn
tool off and disconnect tool from
power source before making any
adjustments or removing/installing
attachments or accessories.
Proper Hand Position (fig. 13)
WARNING: To reduce the risk of
serious personal injury, ALWAYS
use proper hand position as shown
in figure 13.
WARNING: To reduce the risk of
serious personal injury, ALWAYS hold
securely in anticipation of a sudden
reaction.
Proper hand position requires one hand on the main
handle (i), with the other hand on the side handle (h).
Drill Operation
1. Select the desired speed/torque range using
the gear shifter to match the speed and torque
to the planned operation. Set the mode control
collar to the drill symbol.
2. For WOOD, use twist bits, spade bits, power
auger bits or hole saws. For METAL, use highspeed steel twist drill bits or hole saws. Use
a cutting lubricant when drilling metals. The
exceptions are cast iron and brass which should
be drilled dry.
3. Always apply pressure in a straight line with the
bit. Use enough pressure to keep the drill bit
biting, but do not push hard enough to stall the
motor or deflect the bit.
4. Hold tool firmly with both hands to control the
twisting action of the drill.
5. IF DRILL STALLS, it is usually because it
is being overloaded. RELEASE TRIGGER
IMMEDIATELY, remove drill bit from work,
and determine cause of stalling. DO NOT
CLICK TRIGGER OFF AND ON IN AN
ATTEMPT TO START A STALLED DRILL –
THIS CAN DAMAGE THE DRILL.
6. Keep the motor running when pulling the bit
back out of a drilled hole. This will help prevent
jamming.
To release the accessory, repeat Steps 1 and 2.
OPERATION
Instructions for Use
WARNING: Always observe the safety
instructions and applicable regulations.
14
Screwdriver Operation (fig. 4–6)
1. Select the desired speed/torque range using the
three-speed gear shifter (g) on the top of tool
to match the speed and torque to the planned
application. Initially set the torque adjustment
ENGLISH
collar (e) at a lower setting to ensure the
fastener to be set to your specification.
NOTE: Use the lowest torque setting required
to seat the fastener at the desired depth. The
lower the number, the lower the torque output.
Lubrication
Your power tool requires no additional lubrication.
2. Rotate the mode control collar (f) so the screw
symbol is aligned with the arrow.
3. Reset the torque adjustment collar (e) to the
appropriate number setting for the torque
desired. Make a few practice runs in scrap or
unseen areas to determine the proper position
of the torque adjustment collar.
NOTE: The torque adjustment collar may be
set to any number at any time. However, the
torque adjustment collar is only engaged during
screwdriving mode and not in drill and hammerdrill
modes.
Hammerdrill Operation
1. Select the desired speed/torque range using
the gear shifter to match the speed and torque
to the planned operation. Set the mode control
collar to the hammer symbol.
2. When drilling, use just enough force on the
hammer to keep it from bouncing excessively.
Too much force will cause slower drilling
speeds, overheating, and a lower drilling rate.
3. Drill straight, keeping the bit at a right angle to
the work. Do not exert side pressure on the bit
when drilling as this will cause clogging of the
bit flutes and a slower drilling speed.
4. When drilling deep holes, if the hammer speed
starts to drop off, pull the bit partially out of
the hole with the tool still running to help clear
debris from the hole.
5. For masonry, use carbide-tipped bits or
masonry bits. A smooth, even flow of dust
indicates the proper drilling rate.
MAINTENANCE
Your DEWALT power tool has been designed to
operate over a long period of time with a minimum
of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
WARNING: To reduce the risk of
serious personal injury, turn tool
off and disconnect battery pack
before making any adjustments or
removing/installing attachments or
accessories. An accidental start-up
can cause injury.
Cleaning
WARNING: Blow dirt and dust out of
the main housing with dry air as often as
dirt is seen collecting in and around the
air vents. Wear approved eye protection
and approved dust mask when
performing this procedure.
WARNING: Never use solvents or
other harsh chemicals for cleaning the
non-metallic parts of the tool. These
chemicals may weaken the materials
used in these parts. Use a cloth
dampened only with water and mild
soap. Never let any liquid get inside the
tool; never immerse any part of the tool
into a liquid.
CHARGER CLEANING INSTRUCTIONS
WARNING: Shock hazard. Disconnect
the charger from the AC outlet before
cleaning. Dirt and grease may be
removed from the exterior of the charger
using a cloth or soft non-metallic brush.
Do not use water or any cleaning
solutions.
Optional Accessories
WARNING: Since accessories, other
than those offered by DEWALT, have
not been tested with this product, use
of such accessories with this tool could
be hazardous. To reduce the risk of
injury, only DEWALT, recommended
accessories should be used with this
product.
Consult your dealer for further information on the
appropriate accessories.
Protecting the Environment
Separate collection. This product must
not be disposed of with normal
household waste.
The charger is not serviceable. There are no
serviceable parts inside the charger.
15
EN GLI S H
Should you find one day that your DEWALT product
needs replacement, or if it is of no further use to you,
do not dispose of it with household waste. Make this
product available for separate collection.
Separate collection of used products
and packaging allows materials to be
recycled and used again. Re-use of
recycled materials helps prevent
environmental pollution and reduces
the demand for raw materials.
Local regulations may provide for separate collection
of electrical products from the household, at
municipal waste sites or by the retailer when you
purchase a new product.
DEWALT provides a facility for the collection and
recycling of DEWALT products once they have
reached the end of their working life. To take
advantage of this service please return your product
to any authorised repair agent who will collect them
on our behalf.
You can check the location of your nearest
authorised repair agent by contacting your local
DEWALT office at the address indicated in this
manual. Alternatively, a list of authorised DEWALT
repair agents and full details of our after-sales
service and contacts are available on the Internet at:
www.2helpU.com.
GUARANTEE
DEWALT is confident of the quality of its
products and offers an outstanding guarantee
for professional users of the product. This
guarantee statement is in addition to and in
no way prejudices your contractual rights as a
professional user or your statutory rights as a
private non-professional user. The guarantee is
valid within the territories of the Member States
of the European Union and the European Free
Trade Area.
• 30 DAY NO RISK
SATISFACTION GUARANTEE •
If you are not completely satisfied with the
performance of your DEWALT tool, simply return
it within 30 days, complete with all original
components, as purchased, to the point of
purchase, for a full refund or exchange. The
product must have been subject to fair wear and
tear and proof of purchase must be produced.
• ONE YEAR FREE SERVICE CONTRACT •
If you need maintenance or service for your
DEWALT tool, in the 12 months following
purchase, it will be undertaken free of charge
at an authorised DEWALT repair agent. Proof of
purchase must be produced. Includes labour.
Excludes accessories and spare parts unless
failed under warranty.
• ONE YEAR FULL WARRANTY •
Rechargeable Battery Pack
This long life battery pack must be recharged when
it fails to produce sufficient power on jobs which
were easily done before. At the end of its technical
life, discard it with due care for our environment:
• Run the battery pack down completely, then
remove it from the tool.
• Li-Ion, NiCd and NiMH cells are recyclable. Take
them to your dealer or a local recycling station.
The collected battery packs will be recycled or
disposed of properly.
If your DEWALT product becomes defective
due to faulty materials or workmanship within
12 months from the date of purchase, DEWALT
guarantees to replace all defective parts free of
charge or – at our discretion – replace the unit
free of charge provided that:
• The product has not been misused;
• The product has been subject to fair wear
and tear;
• Repairs have not been attempted by
unauthorised persons;
• Proof of purchase is produced;
• The product is returned complete with all
original components.
If you wish to make a claim, contact your seller
or check the location of your nearest authorised
DEWALT repair agent in the DEWALT catalogue
or contact your DEWALT office at the address
indicated in this manual. A list of authorised
DEWALT repair agents and full details of our
after-sales service is available on the Internet at:
www.2helpU.com.
16
17
Belgique et Luxembourg
België en Luxemburg
Black & Decker - DEWALT
Nieuwlandlaan 7, IZ Aarschot B156
B-3200 Aarschot
Tel:
+32 (0)015 - 15 47 9211
Fax:
+32 (0)015 - 15 47 9210
www.dewalt.be
Danmark
DEWALT
Sluseholmen 2-4
2450 København SV
Tlf:
70201511
Fax:
70224910
www.dewalt.dk
Deutschland
DEWALT
Richard-Klinger-Straße
65510 Idstein
Tel:
06126-21-1
Fax:
06126-21-2770
www.dewalt.de
Ελλάς
Black & Decker (Hellas) S.A.
Στράβωνος 7 & Βουλιαγμένης 159
Γλυφάδα 16674, Αθήνα
Τηλ:
(01) 8981-616
Φαξ:
(01) 8983-570
Service: (01) 8982-630
España
DEWALT
Parque de Negocios “Mas Blau”
Edificio Muntadas, c/Bergadá, 1, Of. A6
08820 El Prat de Llobregat (Barcelona)
Tel:
934 797 400
Fax:
934 797 439
www.dewalt.es
France
DEWALT
5, allée des hêtres
BP 30084, 69579 Limonest Cedex
Tel:
04 72 20 39 20
Fax:
04 72 20 39 00
www.dewalt.fr
Schweiz
Suisse
Svizzera
DEWALT
In der Luberzen 40
8902 Urdorf
Tel:
01 - 730 67 47
Fax:
01 - 730 70 67
www.dewalt.ch
Ireland
DEWALT
Calpe House Rock Hill
Black Rock, Co. Dublin
Tel:
00353-2781800
Fax:
00353-2781811
www.dewalt.ie
Italia
DEWALT
Viale Elvezia 2
20052 Monza (Mi)
Tel:
800-014353
Fax:
039-2387592
www.dewalt.it
Nederlands
Black & Decker - DEWALT
Joulehof 12
4600 AB Bergen Op Zoom
Tel:
0164 283000
Fax:
0164 283100
www.dewalt.nl
Norge
DEWALT
Postboks 4814, Nydalen
0422 Oslo
Tel:
22 90 99 00
Fax:
22 90 99 01
www.dewalt.no
Österreich
DEWALT
Werkzeugevertriebs GmbH
Erlaaerstraße 165, Postfach 320,1231 Wien
Tel:
01 - 66116 - 0
Fax:
01 - 66116 - 14
www.dewalt.at
Portugal
DEWALT
Rua Egas Moniz 173
João do Estoril, 2766-651 Estoril
Tel:
214 66 75 00
Fax:
214 66 75 75
www.dewalt.pt
Suomi
DEWALT Oy
Tekniikantie 12
02150 Espoo, Finland
Puh:
010 400 430
Faksi: 0800 411 340
www.dewalt.fi
DEWALT Oy
Teknikvägen 12
02150 Esbo, Finland
Tel:
010 400 430
Fax:
0800 411 340
www.dewalt.fi
Sverige
DEWALT
Box 94
431 22 Mölndal
Tel:
031 68 61 00
Fax:
031 68 60 08
www.dewalt.se
Türkiye
KALE Hırdavat ve Makina A.Ş.
Defterdar Mah. Savaklar Cad. No:15
Edirnekapı / Eyüp / İSTANBUL 34050 TÜRKİYE
Tel:
0212 533 52 55
Faks: 0212 533 10 05
www.dewalt.com.tr
United Kingdom
DEWALT
210 Bath Road
Slough, Berks SL1 3YD
Tel:
01753-56 70 55
Fax:
01753-57 21 12
www.dewalt.co.uk
N042765
10/09