Viking PS0107VR Installation guide

Viking Installation Guide
Built-In Gas Rangetops
VIKING RANGE CORPORATION
111 Front Street
Greenwood, Mississippi 38930 USA
IMPORTANT - PLEASE READ AND FOLLOW
•Before beginning, please read these instructions completely
and carefully.
•Do not remove permanently affixed labels, warnings, or plates
from the product. This may void the warranty.
•Please obseve all local and national codes and ordinances.
•Please ensure that this product is properly grounded.
•The installer should leave these instructions with the
consumer who should retain for local inspector’s use and for
future reference.
Installation must conform with national and local codes or in
the absence of codes, the National Fuel Gas Code, ANSI
Z223.-latest edition. Electrical installation must be in
accordance with National Electrical Code, ANSI/NFPA 70
and/or local codes. IN CANADA: Installation must be in
accordance with the current CAN/CGA B149.1 & 2 Gas
Installation codes and/or local codes. Electrical installation
must be in accordance with the current CSA C22.1 Canadian
Electrical Codes Part 1 and/or local codes.
Installation of any gas-fired equipment should be made by a
licensed plumber. A manual gas shut-off valve must be
installed in the gas supply line ahead of the oven in the gas
stream for safety and ease of service.
In Massachusetts: All gas products must be installed by a
“Massachusetts” licensed plumber or gasfitter. A “T” handle
type manual gas valve must be installed in the gas supply line
to the appliance.
WARNING!!
ELECTRICAL GROUNDING INSTRUCTIONS
This rangetop must be electrically grounded in accordance
with local codes. This appliance is equipped with a threeprong plug for your protection against shock hazard and
should be plugged directly into a properly grounded
reeptacle. Do not cut or remove the grounding prong from
this plug.
FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE
PROPERLY GROUNDED
2
WARNING: IF THE INFORMATION IN
THIS MANUAL IS NOT FOLLOWED
EXACTLY, A FIRE OR EXPLOSION MAY
RESULT CAUSING PROPERTY DAMAGE,
PERSONAL INJURY, OR DEATH.
1. Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any
other appliance.
2. WHAT TO DO IF YOU SMELL GAS:
•Do not try to light any appliance.
•Do not touch any electrical switch; do not use
any phone in your building.
•Immediately call your gas supplier from a
neighbor’s phone.
•Follow the gas supplier’s instructions.
•If you cannot reach your gas supplier, call the
fire department.
3. Installation and service must be performed by a
qualified installer, service agency, or the gas
supplier.
WARNING
If not installed, operated and maintained in
accordance with the manufacturer’s instructions,
this product could expose you to substances in
fuel or from fuel combustion which can cause
death or serious illness and which are known to
cause cancer, birth defects, or other reproductive
harm.
For example, benzene is a chemical which is
part of the gas supplied to the cooking product.
It is consumed in the flame during combustion.
However exposure to a small amount of
benzene is possible if a gas leak occurs.
Formaldehyde and soot are by-products of
incomplete combustion. Properly adjusted
burners with a bluish rather than yellow flame
will minimize incomplete combustion.
Basic Specifications
VGRT Models
Description
Overall width
Overall height
24” W. Models
23 7/8” (60.6 cm)
To
To
To
To
To
top
top
top
top
top
of
of
of
of
of
Overall depth from
rear
Cutout width
Cutout Height
Cutout Depth
Electrical
requirements
Gas requirements
Maximum amp
usage
Surface burner
rating
Approximate
Shipping Wt.
30” W. Models
29 7/8” (75.8 cm)
(Open top Burners only)
spider grate 9 1/4” (23.5 cm)
(Sealed Burners only)
burner grate 9 1/8” (23.2 cm)
island trim 8 7/8” (22.5 cm)
6” backguard13 7/8” (35.2 cm)
high shelf 31 3/8” (79.7 cm)
To end of side panel 24” (61.0 cm)
To end of control panel 25 3/4” (65.4 cm)
To end of knobs 27 3/4” (70.5 cm)
24” (61.0 cm)
30” (76.2 cm)
Open top Burners - 7 1/2” (19.1 cm) (top of grate support should be 3/8” [1.0 cm] above countertop.
Sealed Burners- 7 5/8” (19.4 cm) (top of side trim should be 3/8” [1.0 cm] above countertop.
Minimum 24” (61.0 cm)
Maximum 25 3/4” (65.4 cm)
120 VAC/60 Hz 4ft. (121.9 cm), 3-wire cord with grounded 3-prong plug
Shipped natural or LP/Propane gas ; field convertible with conversion kit (purchased separately);
accepts standard residential 1/2” (1.3 cm) ID gas service line
.3 amps
.3 amps
100 lbs.
(45.0 kg)
15.000 BTU Nat./13,500 BTU LP/Propane
(4.4 kW Nat./4.0 kW LP/Propane)
125 lbs.
(56.3 kg)
Minimum clearances from adjacent combustible construction
•Cooking surface and below (36” [91.4 cm ] and below)
•Sides - 0”
•Rear - 0” with backguard or high shelf; 0” with island trim and non-combustible rear wall; 6” (15.2 cm) with
island trim and combustible rear wall.
•Top grate support - 36” (91.4 cm)
•Above cooking surface (above 36” [91.4 cm])
•Sides - 6” (15.2 cm)
•Within 6” (15.2 cm) side clearance, wall cabinets no deeper than 13” (33.0 cm) must be minimum 18” (45.7
cm) above cooking surface.
•Wall cabinets directly above product must be minimum 36” (91.4 cm) for open top burners and 42” (106.7 cm)
for sealed burners above cooking surface.
*It is not recommended to install two or more units side by side.
3
Basic Specifications
VGRT Models
Description
Overall width
Overall height
Overall depth from
rear
Cutout width
Cutout Height
Cutout Depth
Electrical
requirements
Gas requirements
Maximum amp
usage
Surface burner
rating
Wok Burner
rating (If applicable)
Griddle burner
rating
BTU LP
Grill burner
rating
Approximate
Shipping Wt.
36” W. Models
42” W. Models
35 7/8” (91.1 cm)
To top of spider grate To top of burner grate To top of island trim To top of 6” backguardTo top of high shelf -
42” (106.7 cm)
47 7/8” (121.6 cm)
59 1/2” (151.1cm)
(Open top Burners only)
9 1/4” (23.5 cm)
(Sealed Burners only)
9 1/8” (23.2 cm)
8 7/8” (22.5 cm)
13 7/8” (35.2 cm)
31 3/8” (79.7 cm)
To end of side panel 24” (61.0 cm)
To end of control panel 25 3/4” (65.4 cm)
To end of knobs 27 3/4” (70.5 cm)
48” W. Models
60” W. Models
36” (91.4 cm)
42 1/8” (107 cm)
48” (121.9 cm)
59 5/8” (151.4 cm)
Open top Burners - 7 1/2” (19.1 cm) (top of grate support should be 3/8” [1.0 cm] above countertop.
Sealed Burners- 7 5/8” (19.4 cm) (top of side trim should be 3/8” [1.0 cm] above countertop.
Minimum 24” (61.0 cm)
Maximum 25 3/4” (65.4 cm)
120 VAC/60 Hz 4ft. (121.9 cm), 3-wire cord with grounded 3-prong plug
Shipped natural or LP/Propane gas; field convertible with conversion kit (purchases separately);
accepts standard residential 1/2” (1.3 cm) ID gas service line
6B - .6 amps
6G - 4.2 amps
6G - 7.8 amps
4G - 3.9 amps
6Q .6 amps
6GQ- 4.2 amps
4Q - .6 amps
4G - 7.2 amps
4GQ- 4.2 amps
4K .6 amps
4Q - .6 amps
15.000 BTU Nat./13,500 BTU LP/Propane
(4.4 kW Nat./4.0 kW LP/Propane)
N/A
27,500 BTU Nat./LP
N/A
(8.2 kW Nat./LP
12”/18” Wide
24” Wide
15,000 BTU Nat./13,500 BTU LP
Two 15,000 BTU Nat./13,500
(4.4 kW / 4.0 kW )
(4.4 kW / 4.0 kW)
12” Wide - 1 @ 18,000 BTU Nat. (5.3 kW)/ 16,000 BTU LP/Propane (4.7 kW)
24” Wide - 2 @ 15,000 BTU Nat. (4.4 KW) / 13,500 BTU LP/Propane (4.0 kW)
6B-150 lb.(67.5kg)
4G - 160 lb.(72.0kg)
4Q - 155 lb.(69.8 kg)
6G -203 lb.(91.4kg)
6Q -198 lb.(89.1kg)
4G - 213 lb.(95.6kg)
4GQ-208 lb.(93.6 kg)
4K - 213 lb.(95.6 kg)
4Q - 198 lb.(89.1 kg)
6G - 256lb.(115.2kg)
6GQ-251 lb.(113.0kg)
Minimum clearances from adjacent combustible construction
•Cooking surface and below (36” [91.4 cm ] and below)
•Sides - 0”
•Rear - 0” with backguard or high shelf; 0” with island trim and non-combustible rear wall; 6” (15.2 cm) with
island trim and combustible rear wall.
•Top grate support - 36” (91.4 cm)
•Above cooking surface (above 36” [91.4 cm])
•Sides - 6” (15.2 cm)
•Within 6” (15.2 cm) side clearance, wall cabinets no deeper than 13” (33.0 cm) must be minimum 18” (45.7
cm) above cooking surface.
•Wall cabinets directly above product must be minimum 36” (91.4 cm) for open top burners and 42” (106.7 cm)
for sealed burners above cooking surface.
*It is not recommended to install two or more units side by side.
4
Basic Specifications
DGRT Models
Description
Overall width
Overall height
Overall depth from
rear
Cutout width
Cutout Height
Cutout Depth
Electrical
requirements
Gas requirements
30” W. Models
To
To
To
To
top
top
top
top
of
of
of
of
36” W. Models
29 7/8” (759. cm)
35 7/8” (91.1 cm)
grate 6 1/8” (15.6 cm)
island trim 6 1/8” (15.6 cm)
6” backguard12 1/8” (30.8 cm)
high shelf 24 1/8” (61.3 cm)
To end of side panel 24 1/2” (62.2 cm)
To end of control panel 26 1/8” (66.4 cm)
To end of knobs 27 5/8” (70.5 cm)
30” (76.2 cm)
36” (91.4 cm)
5 3/4” (14.6 cm) (top of grates should be 3/8” [1.0 cm] above countertop.
24 1/2” (62.2 cm)
120 VAC/60 Hz 4ft. (121.9 cm), 3-wire cord with grounded 3-prong plug
Shipped natural or LP/Propane gas ; field convertible with conversion kit (purchased separately);
accepts standard residential 1/2” (1.3 cm) ID gas service line
2.0 amps
2.0 amps
Maximum amp
usage
Surface burner rating
left front
16,000 BTU Nat./15,500 BTU LP/Propane
(4.7 kW Nat./4.5 kW LP/Propane)
left rear
12,000 BTU Nat./11,500 BTU LP/Propane
(3.5 kW Nat./3.4 kW LP/Propane)
center
N/A
right rear
right front
Approximate
8,000 BTU Nat./7,500 BTU LP/Propane
(2.0 kW Nat./1.9 kW LP/Propane)
6,000 BTU Nat./5,500 BTU LP/Propane
(1.5 kW Nat./1.4 kW LP/Propane)
125 lbs. (56.3 kg)
12,000 BTU Nat./11,500 BTU LP/Propane
(3.5 kW Nat./3.4 kW LP/Propane)
10,000 BTU Nat./9,500 BTU LP/Propane
(2.5 kW Nat./2.4 LP/Propane)
16,000 BTU Nat/15,500 BTU LP/Propane
(4.7 kW Nat./4.5 kW LP/Propane)
8,000 BTU Nat./7,500 BTU LP/Propane
(2.0 kW Nat./1.9 kW LP/Propane)
6,000 BTU Nat./5,500 kW LP/Propane
(1.5 kW Nat./1.4 kW LP/Propane)
150 lb.(67.5kg)
Shipping Wt.
Minimum clearances from adjacent combustible construction
•Cooking surface and below (36” [91.4 cm ] and below)
•Sides - 0”
•Rear - 0” with backguard or high shelf; 0” with island trim and non-combustible rear wall; 6” (15.2 cm) with
island trim and combustible rear wall.
•Top grate support - 36” (91.4 cm)
•Above cooking surface (above 36” [91.4 cm])
•Sides - 6” (15.2 cm)
•Within 6” (15.2 cm) side clearance, wall cabinets no deeper than 13” (33.0 cm) must be minimum 18” (45.7
cm) above cooking surface.
•Wall cabinets directly above product must be a minimum 42” (106.7 cm) for sealed top burners
*It is not recommended to install two or more units side by side.
5
GENERAL INFORMATION
1. WARNING:: The use of cabinets for storage above the appliance may result in a potential burn hazard.
Combustible items may ignite, metallic items may become hot and cause burns. If a cabinet storage is to be
provided the risk can be reduced by installing a rangehood that projects horizontally a minimum of 5” (12.7 cm)
beyond the bottom of the cabinets.
2. All openings in the wall behind the appliance and in the floor under the appliance shall be sealed.
3. Keep appliance area clear and free from combustible materials, gasoline, and other flammable vapors.
4. Do not obstruct the flow of combustion and ventilation air.
5. Disconnect the electrical supply to the appliance before servicing.
6. When removing oven for cleaning and/or service;
A. Shut off gas at main supply
B. Disconnect AC power supply
C. Disconnect gas line to the inlet pipe.
D. Carefully remove the rangetop by pulling out of cabinet cutout.
E. When cleaning and/or service is complete, replace unit in cabinet cutout, reconnect gas line and power
supply, and turn on gas at main supply.
7. Electrical Requirement
Listed on Specification sheet. Electrical installation should comply with national and local codes.
8. Gas Manifold Pressure:
Natural gas 5.0” W.C.P.
LP/Propane 10.0” W.C.P.
WARNING
Never use this appliance as a space heater to heat or warm the room. Doing
so may result in carbon monoxide poisioning and over heating of the unit.
GAS INLET/ELECTRICAL LOCATION
A
B
3/4” Min.
(1.9 cm)
VGRT Models 24”, 30”, 36”, 42”,48” W.
VGRT Models 60” W.
DGRT Models 30”, 36” W.
A
Min. 24” (61.0 cm)
Max. 25 3/4 (65.4 cm)
Min. 24” (61.0 cm)
Max. 25 3/4 (65.4 cm)
Min. 24 1/2” (62.2 cm)
Max. 26 1/8” (66.4 cm)
B
3” (7.6 cm)
14 3/8” (36.5 cm)
3” (7.6 cm)
6
C
2 1/4” (5.7 cm)
9/16” (1.8 cm)
2 1/4” (5.7 cm)
Proximity to Side Cabinet Installation
1. This rangetop may be installed directly adjacent to existing 36” (91.4 cm) high base cabinets. IMPORTANT: The
top grate support MUST be 3/8” (.95 cm) above the adjacent base cabinet countertop.
2. The rangetop CANNOT be installed directly adjacent to sidewalls, tall cabinets, tall appliances, or other side vertical
surfaces above 36” (91.4 cm) high. There must be a minimum of 6” (15.2 cm) side clearance from the rangetop to
such combustible surfaces above the 36” (91.4 cm) counter height.
3. Within the 6” (15.2 cm) side clearance to combustible vertical surfaces above 36” (91.4 cm) , the maximum wall
cabinet depth must be 13” (33.0 cm) and wall cabinets within this 6” (15.2 cm) side clearance must be 18” (45.7 cm)
above the 36” (91.4 cm) high countertop.
4. Wall cabinets above the rangetop must be a minimum of 36” (91.4 cm) for the open top burner models and a
minimum of 42” (106.7 cm) for the sealed burner models above the rangetop cooking surface for the full width of
the rangetop. This minimum height requirement does not apply if a rangehood is installed over the cooking
surface.
Dim. 24” W. Models
A
24” (61.0 cm)
Dim.
VGRT Open Burners
VGRT Sealed Burners
DGRT Sealed Burners
30” W. Models
30” (76.2 cm)
36” W. Models
36” (91.4 cm)
B
36” (91.4 cm) min.
42” (106.7 cm) min.
42” (106.7 cm) min.
42” W. Models
48” W. Models
42 1/8” (107.0 cm) 48” (121.9 cm)
C
7 1/2” (19.1 cm)
7 5/8” (19.4 cm)
5 3/4” (14.6 cm)
B
A
C
7
60” W. Models
59 5/8” (151.4 cm)
WOOD/COMPOSITE OVERLAY INSTALLATION
(Including Custom Ventilator Installation)
The bottom of any hood should be 30” (68.6 cm) min. to 36” (91.4) max. above the countertop. This would
typically result in the bottom of the hood being 66” (167.6 cm) to 72” (182.9 cm) above the floor. Refer to the
rangehood installation instructions for additional information. These dimensions provide for safe and efficient
operation of the hood.
WALL INSTALLATION
ISLAND INSTALLATION
Wood/Composite Overlay
Wood/Composite Overlay
Metal Hood
Metal Hood
30” (76.2 cm) Min.
36” (91.4 cm) Max
30” (76.2 cm) Min.
36” (91.4 cm) Max
66” (167.6 cm)
Min.
to
72” (182.9 cm)
Max.
66” (167.6 cm)
Min.
to
72” (182.9 cm)
Max.
Countertop
36”
(91.4 cm)
36”
(91.4 cm)
8
Countertop
Gas Connection
All gas connections must be made according to national and local codes. This gas supply (service) line must be the
same size or greater than the inlet line of the appliance. This rangetop uses an ISO7 or ISO128 inlet. The inlet
depends on the end users national and local codes.
1. Manual Shut-off Valve:
This installer-supplied valve must be installed in the gas service line ahead of the appliance in the gas stream and in
a position where it can be reached quickly in the event of an emergency. In Massachusetts: A “T” type handle
manual gas valve must be installed in the gas supply line to the appliance.
2. Pressure Regulator
a) All heavy duty cooking equipment must have a pressure regulator on the incoming service line for safe and
efficient operation, since service pressure may fluctuate with local demand. External regulators are not
required on this rangetop, because a regulator is built into each unit at the factory. Under no condition
bypass this built-in regulator.
b) Any conversion required must be performed by your dealer or a qualified licensed plumber or gas service
company. Please provide the service person with this manual before work is started on the range. (Gas
conversions are the responsibility of the dealer or end user.)
c) This rangetop can be used with Natural or LP/Propane gas. It is shipped from the factory adjusted for use
with natural gas. To convert to LP/Propane, see conversion instructions on page 11.
d) Manifold pressure should be checked with a manometer, natural gas requires 5.0” W.C.P. and LP/Propane
requires 10.0” W.C.P. Incoming line pressure upstream from the regulator must be 1” W.C.P. higher than
the manifold pressure in order to check the regulator. The regulator used on this range can withstand a
maximum input pressure of 1/2 PSI (14.0” W.C.P.) If the line pressure is in excess of that amount, a stepdown regulator will be required.
e) The appliance, its individual shut-off valve, and pressure regulator must be disconnected from the gas
supply piping system during any pressure testing of that system at pressures in excess of 1/2 psig (3.45 kPa).
f) The appliance must be isolated from the gas supply piping system by closing its individual manual shut-off
valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2
psig (3.45 kPa).
3. Flexible Connections:
a) If the unit is to be installed with flexible couplings and/or quick disconnect fittings, the installer must use a
heavy-duty, agency approved flexible connector of at least 1/2” (1.3 cm) ID NPT (with suitable strain reliefs)
in compliance with ANSI Z21.41 and Z21.69 standards.
b) In Canada: CAN 1-6.10-88 metal connectors for gas appliances and CAN 1-6.9 M79 quick disconnect
device for use with gas fuel.
c) In Massachusetts: The appliance must be installed with a 36” (3-foot) long flexible gas connector.
CAUTION: Leak testing of the appliance shall be conducted according to the manufacturer’s instructions. Before
placing the rangetop into operation, always check for leaks with a soapy water solution of other acceptable method.
DO NOT USE AN OPEN FLAME TO CHECK FOR LEAKS!
Electrical Connection
There is no connection necessary beyond plugging the unit into a polarized, grounded, 120 volt, 60 Hz, 15 amp circuit.
The minimum of 102 VAC is required for proper operation of gas ignition systems. Do not use GFI circuit. This circuit,
however, MUST be grounded and properly polarized. The unit is equipped with a 16-SPT2 power cord.
WARNING!!
Electrical Grounding Instructions
This appliance is equipped with a three prong grounding plug for your protection against shock hazard and should be
plugged directly into a properly grounded receptacle. Do not cut or remove the grounding prong from the plug.
9
Surface Burner Adjustments (For Open Surface Burners)
(See Illustration #2)
To gain access to the surface burner adjustments:
1. Remove the grates, burner caps, bowls and grate supports.
2. Located the air shutter (A) and loosen the screw (B) that holds the air shutter in place.
3. Remove the drip tray, allowing you work space to adjust the orifice hood (C).
4. Replace grate support and burner bowls (this allows for correct air flow, as in normal use).
5. Light each burner by rotating the burner valve shaft (D) to high position.
6. With a proper flame height, adjust the air shutter (A) to obtain a blue flame with no yellow tipping that sits on the
burner at the burner ports.
a) Open the air shutter gap to eliminate yellow tipping.
b) Close the air shutter gap to prevent a noisy flame that lifts off the burner.
7. Turn the surface burners off.
8. Replace the drip tray.
9. Remove grate support and burner bowls.
10. Tighten the air shutter screw (B) being careful to not change the adjusted shutter gap.
11. Replace the grate supports, burner bowls, burner caps, and grates.
12. Turn the lighted burners to the low flame setting.
13. Insert a narrow, flat-blade screwdriver into the hollow shaft of the surface burner valve, and engage the slotted low
flame adjustment screw. The low flame should be a small flame that comes just to the top edge of the burner.
Rotate the adjusting screw (E) clockwise to lower the flame or counter clockwise to increase the flame. Turn the
burner off and relight several times, turning to the low position. The low flame should light at every port each
time. Readjust as needed.
Illustration #2
Surface Burner Adjustments (For Sealed Surface Burners)
(See Illustration #2)
1. Turn the lighted burners to the low flame setting.
2. Insert a narrow, flat-blade screwdriver into the hollow shaft of the surface burner valve, and engage the slotted low
flame adjustment screw. The low flame should be a small flame that comes just to the top edge of the burner.
Rotate the adjusting screw (E) clockwise to lower the flame or counter clockwise to increase the flame. Turn the
burner off and relight several times, turning to the low position. The low flame should light at every port each time.
Readjust as needed.
Flame adjustment
screw
Surface burner valve
(behind control knob)
Flathead
screwdriver
Flame Height
10
Wok Burner Adjustment
To gain access to the burner for adjustments:
A
1. Remove the grate and grate support.
2. Locate the air shutter “A” and loosen the two screws “B” that holds the
air shutter in place.
3. Light the burner and turn the burner knob to the high position.
4. With a proper, high flame height, adjust the air shutter to obtain a blue
flame with no yellow tipping that sits on the burner at the burner ports.
(a) open the air shutter gap to add more air and to eliminate yellow
tipping.
(b) close the air shutter gap to reduce the air and to prevent a noisy
flame that lifts off the burner.
5. Turn the surface burners off.
6. Tighten the air shutter screws.
7. Replace the grate support and grate.
B
AIR SHUTTER
3/4” (1.91 cm)
Air Shutter
Orifice
FLAME HEIGHT
OVERHEAD VIEW
11
Grill/Griddle Burner Adjustment
12” Grill Assembly
Grill
24” Grill Assembly
1
1. The grill burner orifice and air shutter are located beneath the front
end of the grill assembly. To gain access to the adjustment, remove
the grill grate, grate support, flavor generators, and the burner shield.
2
2. Remove the screw at the front and rear of the burner.
3. Lift the burner off the orifice and locate the air shutter adjustment
3
screw at the end of the burner. (See Detail “A”)
4. Loosen the screw and adjust the air shutter to the desired setting
4
[for natural gas open shutter approximately 7/16” (1.1 cm); for LP
5
gas open the air shutter approximately 3/8” (.95 cm)].
5. Tighten the screw, then replace the burner on the orifice.
6
6. Check the flame for desired height before replacement of the above
parts.
7. The flame adjustments are the same as the surface burners. Use a
1. Grill Grates
1/2” (1.3 cm) deep socket to adjust the orifice head; turn clockwise
2. Flavor Generator
to decrease flame and counter clockwise to increase flame.
plates
3. Heat Deflector
4. Grill Frame
5. Grill Burner Sheild
(Do not remove
from burner)
6. Burner
(Do not remove)
Detail A
Griddle
1. To gain access to the burner orifice and air shutter, remove grates and grate supports located on either side of the
griddle. Lift and remove the griddle. CAUTION: Before fully removing the griddle assembly, lift the griddle
assembly approximately 4” above the griddle box. Carefully remove the temperature probe from the probe
bracket. (See Detail “B”) Make note of the position of the temperature probe so it can be reinstalled
properly. Failure to properly reinstall can result in damage to the temperature probe.
2. Carefully remove the ignitor and put to the side.
3. Remove the metal plate located below the burner.
4. Remove the screws at the front and rear of the burner, remove the burner tube and locate the air shutter adjustment
screw at the end of the burner tube.
5. Flame adjustments are the same as the grill #4-#7.
6. Replace all griddle parts and griddle.
Probe Bracket
Griddle
Burner
Detail B
12
Initial Ignition of Burners (For Open Surface Burners)
All rangetops are tested before leaving the factory. Field adjustments may be necessary for proper mixture of gas and
air for proper operation. When the rangetop is connected to gas and electric service, it should be adjusted by a
qualified technician. When adjustments are required, contact your dealer/installer for corrections. If assistance is not
available, contact Viking Range Corporation Preferred Service for the nearest authorized service agent at (662) 4514133. All corrections to installation are the responsibility of the dealer/installer or end user.
Initial Ignition of Burners (For Sealed Surface Burners)
All sealed top rangetops are tested before leaving the factory. There are no adjustments for the sealed surface burners
if connected according to the information on the rating plate. Check each burner for proper operations. Flames
should be blue in all settings. If service is required, contact your dealer for the name of their authorized service agency.
If none is available, contact Viking Preferred Service for the nearest authorized service agency in your area. Gas
conversions and initial installation are not the responsibility of the manufacturer.
Performance Checklist
The installer should carry out the following performance checks. Refer to instructions below.
1.
2.
3.
4.
5.
6.
6.
Check surface burner ignition.
Check air shutter adjustment - sharp blue flame, no yellow tipping, sooting or flame lifting
Check low flame adjustment - surface burner valve center stem adjustment.
Check griddle ignition - all burner ports.
Check grill ignition - all burner ports.
Visually check tubular burner reignition to be sure both sides are relighting each time.
Check for gas leaks (odors) at all gas connections. (See page 7 for procedure on checking for gas leaks)
Final Preparation
1. Some stainless steel parts may have a plastic protective wrap which must be removed.
2. All stainless steel body parts should be wiped with hot, soapy water and with a liquid cleaner designed for this
material. If buildup occurs, do not use steel wool, abrasive cloths, cleaners, or powders! If it is necessary to scrape
stainless steel to remove encrusted materials, soak with hot, wet cloths to loosen the material, then use a wood or
nylon scraper. Do not use a metal knife, spatula, or any other metal tool to scrape stainless steel! Scratches are
almost impossible to remove.
NOTE: These installation instructions should remain with the unit for future reference. The electrical diagram is located
beneath the drip tray in the rear corner of the burner box.
Replacement Parts
Only authorized replacement parts may be used in performing service on the oven. Replacement parts are available
from factory authorized parts distributors. Contact Viking Range Corporation Preferred Service, (888) 845-4641, for the
nearest parts distributor in your area.
13
WIRING DIAGRAM
BUILT-IN GAS DESIGNER RANGETOPS
WARNING - Electrical
grounding
instructions
This appliance is equipped with
a three-prong grounding plug
for your protection against
shock hazard and should be
plugged directly into a properly
grounded socket.
CAUTION - Label all wires
prior to disconnection when
servicing controls. Wiring errors
can cause improper and
dangerous operation. Verify
proper operation after servicing.
REFER ONLY TO FEATURES
WHICH ARE EQUIPPED
WITH THIS UNIT.
14
WIRING DIAGRAM
BUILT-IN GAS PROFESSIONAL RANGETOPS
VGRT MODELS
WARNING - Electrical grounding instructions
This appliance is equipped with a three-prong grounding plug for your protection
against shock hazard and should be plugged directly into a properly grounded
socket.
CAUTION - Label all wires prior to disconnection when servicing controls. Wiring
errors can cause improper and dangerous operation. Verify proper operation after
servicing.
REFER ONLY TO FEATURES WHICH ARE EQUIPPED WITH THIS UNIT.
15
Viking Range Corporation
111 Front Street
Greenwood, MIssissippi 38930 USA
(662) 455-1200
For more product information
call 1-888-VIKING1 (845-4641)
or visit the Viking web site at
vikingrange.com
F1239M
(PS0107VR)