Crosslee PLC 18"InsetRaised Technical data

0102 095 52541
18”Inset
Raised
User, Installation & Servicing Instructions
This appliance is for use on NATURAL GAS (G20) ONLY at a supply pressure of 20mbar
Please hand this booklet to the user and advise to keep in a safe place
Important Notice: Before disposal of the outer packaging, please enter the product code, purchase and
installation details in section 1.1 of this booklet.
18” Inset Taper 010710
This booklet details instructions for USER (section 1), INSTALLATION (section 2) & SERVICING (section 3).
IMPORTANT NOTICE
It is important for the safe and continued operation of this appliance that the instructions contained in this booklet are
observed!
TABLE OF CONTENTS
Section
Section
1.0
Instructions for Use
1.1
1.2
1.3
1.4
1.5
1.6
Record of purchase/installation
Important notes
Lighting and extinguishing the appliance
Re-laying the coal/pebble bed
Spare parts
Guarantee
2.0
Installation Instructions
2.1
2.2
2.3
2.4
2.5
2.6
2.7
2.8
Important notes
Statutory requirements
Technical data
Installing the appliance (Ventilation)
Flue
Clearance to sides and shelves
Hearth Clearances
Fitting the appliance in position
2.4.4.1 Connecting the gas supply
2.4.4.2 Checking the appliance setting pressure
2.4.4.3 Checking the correct operation
Laying the coal/pebble bed
Clearance of combustion products
Front and Frets (Requirements for ventilation)
Advising the customer
3.0
Maintenance and Servicing
3.1
3.2
3.3
3.4
Removal of debris or soot
Servicing components below the heat engine
Spare parts
Useful telephone numbers
2.4.1
2.4.2
2.4.3
2.4.4
Section
Page 1
18” Inset Taper 010710
Section 1 – Instructions for Use
1.1
RECORD OF PURCHASE/INSTALLATION
18” Inset
Purchase Details
Date of purchase
______ / ______ / ______
Purchase from
_____________________
Address
_____________________
_________________________________________
Installation Details
Date of installation
______ / ______ / ______
Installed by
_____________________
Registration number
_____________________
Telephone number
_____________________
Appliance Details
Serial number
_____________________
(located on rating label)
Product Code
_____________________
(located on white label on outer carton)
It is advisable to have all the above information
available if assistance is required. It will aid our
service department in helping you more efficiently.
Page 2
18” Inset Taper 010710
1.2
IMPORTANT NOTES
18 “ Inset
CAUTION – THIS PACKAGE WEIGHS 6.5Kgs – assess the load before you move it and note any other handling information
on the packaging. If you think the load is beyond your safe capability, DO NOT PUT YOURSELF AT RISK! Seek assistance
from other person(s) and/or use appropriate handling equipment. IT’S YOUR BODY – LOOK AFTER IT!
This appliance is for DECORATIVE PURPOSES ONLY and is manufactured to the requirements of the current issue of EN 509.
This appliance is for use on NATURAL GAS (G20) ONLY, at a supply pressure of 20mbar +/- 1mbar.
This appliance MUST be installed by a REGISTERED INSTALLER. Failure to do so may lead to prosecution.
Ventilation for this appliance must be fitted in accordance with the rules in force and checked regularly for obstructions.
If the appliance is installed in GREAT BRITAIN, additional ventilation is required.
If the appliance is installed in IRELAND, a minimal cross sectional area of 100cm2 is required.
Any permanent flue restriction must be removed and any variable dampers locked fully open or removed. If the flue has been used
previously for solid fuel, it MUST be swept PRIOR to installation.
If any soot accumulation becomes excessive, the fuel effect pieces should be removed from the appliance for cleaning. Cleaning
should be carried out in a sufficiently ventilated area or in the open air, by gently brushing with the pieces held away from your face so
that you avoid inhaling the dust. THE USE OF A NORMAL VACUUM CLEANER IS NOT RECOMMENDED as dust may be blown
back into the room.
This appliance has a naked flame and a fireguard to the current issue of BS 8423 - 2002 should be used for the protection of children,
the elderly and the infirm.
Care must be taken on the selection of wall coverings within close proximity of the appliance as some vinyl and embossed materials
may become discoloured by convected heat. Soft furnishings must be kept clear from the radiant heat of the appliance and from
impinging the hearth area. Combustible materials must not be put on or left in the hearth area nor should the coal bed be used to burn
rubbish or other materials.
This appliance uses fuel effect components, gaskets and insulation material containing Refractory Ceramic Fibre, (RCF), which are
man-made vitreous silicate fibres. Excessive exposure to such material may cause temporary irritation to the eyes, skin and
respiratory tract. Consequently, it makes sense to take care when handling these articles to ensure that the release of dust is kept to a
minimum.
This appliance is fitted with an ODS, a spillage monitoring system which operates if the evacuation of products is interrupted (i.e.
blocked or incorrect flueing). If the appliance repeatedly `goes out’ it may indicate a problem and the installer or specialist should be
consulted before further use.
o
The minimum temperature rating of any back panel or hearth must have a minimum fire resistance rating of CLASS 0 (100 C).
If any home improvements i.e. double glazing are carried out after this appliance has been installed, you should contact your
Registered Installer and have the operation of the flue checked.
1.3
LIGHTING AND EXTINGUISHING THE APPLIANCE
1.
Remove the fret (Fig. 1), to gain access to the controls (Fig. 2).
Fig. 2
Fig. 1
2.
3.
4.
5.
6.
7.
8.
Fret
Piezo Button
Gas Control
Press and turn the gas control anti-clockwise to the `IGN’ position. Keep the control fully depressed.
Press and release the piezo button until the main burner behind the simulated front coal has lit.
Once lit, keep the gas control depressed for a further 15 seconds.
Release the gas control and check that the main burner has remained alight.
Press and turn the gas control anti-clockwise to the required setting. Replace the fret (controls cover).
To turn the appliance off, depress and turn the gas control clockwise from any position to the `OFF’ position.
In the event of the piezo button failing, the appliance may be lit by placing a lighted taper or match at the main burner while depressing
the gas control in the `IGN’ position.
IMPORTANT
After turning off or if the appliance goes out for any reason, wait for three minutes before attempting to relight.
Page 3
18” Inset Taper 010710
1.4
RE - LAYING THE BED
18 “ Inset
Fig. 3
The support shelf is positioned on the fibre support
metalwork. There are two metal `stops’ that prevent
the support shelf from sitting on the main burner outlet
(Fig. 3).
Fig. 4
Metal `stops’
The simulated front is positioned on the shelf directly
in front of the support shelf. Two metal `stops’ locate the
simulated front in position.
Fit the two front retaining brackets with the two No 8x3/8 screws
supplied in the fixing pack to secure the front into position (Fig. 4).
Note: Large coals/pebbles (grey) and small coals/pebbles
(black) are coloured for illustration purposes only!
Fig. 5
Metal `stops’
Front Retaining Bracket
Place 6 large coals/pebbles on top of the simulated front (one in
each groove). Allow the coals/pebbles to rest on the support
shelf. Place 5 large coals/pebbles on the on the first tier of the
support shelf (Fig. 5).
Fig. 6
Place 6 small coals/pebbles
between the 6 large coals/pebbles
located on top of the simulated front.
Allow the coals/pebbles to rest on
the 5 large coals/pebbles on the first
tier.
Place 4 small coals/pebbles on top
of the 5 large coals/pebbles and
allow them to rest on the back tier of
the support shelf (Fig. 6).
Side View
To obtain the best visual appearance, it may be necessary to `slightly’ adjust the position of the coals.
If any of the coals or coal bed become damaged or lost, replacements MUST be obtained before further use.
ADDITIONAL COALS/PEBBLES MUST NOT BE USED
Page 4
18” Inset Taper 010710
1.5
SPARE PARTS
18” Inset
For a list of spare parts for this appliance, please refer to section 3.3.
1.6
GUARANTEE
Please complete the registration section of the white card supplied in the IFU kit. Any part of this appliance is guaranteed against the
manufacturer’s defective workmanship or faulty materials for a period of twelve months from the date of purchase.
Any such part will be replaced free of charge on receipt of the purchaser’s address at the cost of postage only.
Please take time to fill in section 1.1 of this booklet for your future reference.
Page 5
18” Inset Taper 010710
Section 2 – Instructions for Installation
2.1
IMPORTANT NOTES
18” Inset
CAUTION – THIS PACKAGE WEIGHS 6.5Kgs – assess the load before you move it and note any other handling information
on the packaging. If you think the load is beyond your safe capability, DO NOT PUT YOURSELF AT RISK! Seek assistance
from other person(s) and/or use appropriate handling equipment. IT’S YOUR BODY – LOOK AFTER IT!
This appliance is for DECORATIVE PURPOSE ONLY and is manufactured to the requirements of the current issue of EN 509.
This appliance is for use on NATURAL GAS (G20) ONLY, at a supply pressure of 20 mbar +/- 1mbar.
This appliance MUST be installed by a REGISTERED INSTALLER. Failure to do so may lead to prosecution.
Ventilation for this appliance must be fitted in accordance with the rules in force and checked regularly for obstructions.
If the appliance is installed in GREAT BRITAIN, additional ventilation is required.
2
If the appliance is installed in IRELAND, a minimal cross sectional area of 100cm is required.
Any permanent flue restriction must be removed and any variable dampers locked fully open or removed. If the flue has been used
previously for solid fuel, it MUST be swept PRIOR to installation.
Care must be taken on the selection of wall coverings within close proximity of the appliance as some vinyl and embossed materials
may become discoloured by convected heat. Soft furnishings must be kept clear from the radiant heat of the appliance and from
impinging the hearth area. Combustible materials must not be put on or left in the hearth area nor should the coal bed be used to burn
rubbish or other materials.
This appliance uses fuel effect components, gaskets and insulation material containing Refractory Ceramic Fibre, (RCF), which are
man-made vitreous silicate fibres. Excessive exposure to such material may cause temporary irritation to the eyes, skin and
respiratory tract. Consequently, it makes sense to take care when handling these articles to ensure that the release of dust is kept to a
minimum.
This appliance is fitted with an ODS, a spillage monitoring system which operates if the evacuation of products is interrupted (i.e.
blocked or incorrect flueing). If the appliance repeatedly `goes out’ it may indicate a problem and the installer or specialist should be
consulted before further use.
o
The minimum temperature rating of any back panel or hearth must have a minimum fire resistance rating of CLASS 0 (100 C).
Materials used in the manufacture of this appliance DO NOT contain asbestos.
When fitting or servicing this appliance, care must be taken when handling sheet metal parts to avoid any possibility of personal injury.
If any home improvements i.e. double glazing are carried out after this appliance has been installed, you should contact your
Registered Installer and have the operation of the flue checked.
2.2
STATUTORY REQUIREMENTS
A REGISTERED INSTALLER must carry out the installation of this appliance in accordance with the current issue and relevant
requirements of:9
9
9
9
9
9
9
This installation booklet.
The gas safety (installation and use) regulations.
The building regulations.
The building standards (Scotland) regulations.
The health and safety at work act.
The control of substances hazardous to health.
Any applicable local regulations.
Detailed recommendations are contained in the current issue of the following British Standards and Codes of Practice:BS 5440 Part 1
BS 5440 Part 2
BS 6461 Part 1
BS 5871 Part 3
BS 6891
BS 8303
BS 1251
Specifications for installation of flues.
Specification for installation of ventilation for gas appliances.
Codes of practice for masonry chimneys and flue pipes.
Decorative fuel effect gas appliances of heat input not exceeding 15kW (2nd & 3rd family gases).
nd
Specification for installation of low pressure gas pipe work of up to 28mm (R1) in domestic premises (2 family gases).
Installation of domestic heating and cooking appliances burning solid mineral fuels.
Specification for open-fireplace components.
This installation booklet must not be taken as overriding statutory requirements.
Page 6
18” Inset Taper 010710
2.3
TECHNICAL DATA
18” Inset
Fig. 7
Fig. 8
Minimum
height of
opening is
555mm
Minimum
Depth of
opening is
215mm
295mm
215mm
Minimum
width of
opening is
415mm
415mm
SPECIFICATIONS
2.4
Injector
044/341/196/087M
Gas Control
MP 21301B
Main Burner
Aeromatix AC03/211658
Thermocouple
T100/927-400
Ignition
Single spark electrode direct to main burner
Gas Connection
8mm OD (restrictor elbow)
Gas Type
G20 NATURAL GAS
Maximum Heat Input
7.8kW (26.003btu/hr) Gross
Minimum Heat Input
3.6kW (12,283btu/hr)
Supply Setting Pressure
20mbar +/- 1mbar (Cold)
Flue Types
Class 1
INSTALLING THE APPLIANCE (Ventilation)
Ventilation required for this appliance must be fitted with the rules in force and checked regularly for obstructions:If the appliance is installed in GREAT BRITAIN, additional ventilation is required.
2
If the appliance is installed in IRELAND, a minimal cross sectional area of 100cm is required.
Page 7
18” Inset Taper 010710
2.4.1
INSTALLING THE APPLIANCE (Flue)
18” Inset
Any permanent flue restriction must be removed and any variable dampers locked fully open or removed. If the flue has been used
previously for solid fuel, it MUST be swept PRIOR to installation. This appliance is suitable for installation into CLASS 1 flues ONLY.
540mm
Class 1
A conventional brick or stone chimney with a minimum effective
cross sectional dimension of 225mm x 225mm
415/445mm
A lined flue with a minimum diameter of 175mm having a chair brick
and throat lintel conforming to the current issue of BS 1251 (Fig.
9A).
When an existing refractory chair brick is fitted, the minimum
distance required between the rear of the opening and the front face
of the surround is 215mm. Any remedial work should be carried out
including levelling the base beneath the fire (Fig 9A).
560/590mm
600mm
Fig. 9
Hatched area must be non-combustible.
Min 100mm
Max 65mm
surround or lintel.
215mm
Fig. 9A
Fire
2.4.2
INSTALLING THE APPLIANCE (Clearance to sides and shelves)
The minimum clearance to any combustible material to the side of the appliance must be 150mm (Fig. 10).
The minimum clearance to any non-combustible material around the perimeter of the appliance must be 75mm.
The minimal clearance to the underside of a 150mm depth combustible shelf from the hearth must be 790mm. Add 12.5mm to this
clearance for every 25mm increased depth of shelf (Fig. 10). A `SHELF CHART’ (Fig. 11) is provided to aid in calculating clearances to
shelves.
Fig. 11
SHELF CHART
852.5
Add 12.5mm to clearance for every
25mm increased depth of shelf
840
827.5
Fig. 10
815
790mm
150mm
802.5
Shelf Height 790
Shelf Depth 150
175
200
225
275
250
All dimensions are in MM
Page 8
18” Inset Taper 010710
2.4.3
INSTALLING THE APPLIANCE (Hearth clearances)
18” Inset
A non-combustible hearth with a minimum thickness of 12.5mm and having a perimeter of 50mm above floor level is required to discourage
placing carpets or combustible materials close to the hearth. The width must be a minimum of 150mm either side of the fireplace opening
and a depth of 300mm from the front face of the fire opening (Fig. 12).
Fig. 12
FIRE
OPENING
150mm
300mm
HEARTH AREA
Minimum hearth height - 50mm
Minimum hearth width - 805mm
Minimum hearth thickness - 12.5mm
2.4.4
INSTALLING THE APPLIANCE (Fitting the appliance in position)
BEFORE COMMENCING WORK, TURN OFF ALL APPLIANCES THAT ARE FED BY THE METER.
ISOLATE THE GAS SUPPLY BY TURNING OFF AT THE METER.
Site the appliance as far back in the chairbrick as possible whilst maintaining a central position in the fire opening.
Carefully make a mark in each of the slots in the base of the appliance.
Drill two holes suitable for the fixing plugs provided.
Using the No 10 x 1” woodscrews provided, carefully screw the appliance into position (Fig. 13).
Fig. 13
Fixing Slot
Fixing Slot
2.4.4.1 INSTALLING THE APPLIANCE (Connecting the gas supply)
A restrictor elbow complete with pressure test point is fitted to the appliance to facilitate servicing. The gas supply to the appliance may be
from the front left hand side or as a concealed fitting from the rear left or right hand side. The preferred method of connection should be
from the rear left.
It is important to note the requirements of the current issue of BS 6891, dealing with enclosed pipes. This standard requires that when a
gas pipe is fed through a wall, it should be enclosed in a gas tight sleeve to protect against failure caused by movement and shall be
constructed to prevent passage of gas either between the pipe and sleeve or sleeve and wall.
Page 9
18” Inset Taper 010710
2.4.4.2 INSTALLING THE APPLIANCE (Checking the appliance setting pressure)
18 “ Inset
The pressure test point enables verification of the inlet
pressure at the appliance under operating conditions and
can also be used to check the gas soundness of the
connections to the appliance gas controls (Fig. 14).
Fig. 14
Restrictor elbow c/w PTP
(Pressure Test Point)
Control knob
Piezo ignitor
Rating label
2.4.4.3 INSTALLING THE APPLIANCE (Checking the correct operation)
1.
Remove the fret (Fig. 15), to gain access to the controls (Fig. 16).
Fig. 16
Fret
Fig. 15
2.
3.
4.
5.
6.
7.
8.
Piezo Button
Gas Control
Press and turn the gas control anti-clockwise to the `IGN’ position. Keep the control fully depressed.
Press and release the piezo button until the main burner behind the simulated fron coal has lit.
Once lit, keep the gas control depressed for a further 20 seconds.
Release the gas control and check that the main burner has remained alight.
Press and turn the gas control anti-clockwise to the required setting. Replace the fret.
To turn the appliance off, depress and turn the gas control to the `OFF’ position.
In the event of the piezo button failing, the appliance may be lit by placing a lighted taper or match at the main burner
while depressing the gas control in the `IGN’ position.
IMPORTANT
After turning off or if the appliance goes out for any reason, wait three minutes before attempting to relight.
Page 10
18” Inset Taper 010710
2.5 LAYING THE BED
18 “ Inset
Fig. 17
The support shelf is positioned on the fibre support
metalwork. There are two metal `stops’ that prevent
the support shelf from sitting on the main burner outlet
(Fig. 3).
Fig. 18
Metal `stops’
The simulated front is positioned on the shelf directly
in front of the support shelf. Two metal `stops’ locate the
simulated front in position.
Fit the two front retaining brackets with the two No 8x3/8 screws
supplied in the fixing pack to secure the front into position (Fig. 4).
Note: Large coals/pebbles (grey) and small coals/pebbles
(black) are coloured for illustration purposes only!
Fig. 19
Metal `stops’
Front Retaining Bracket
Place 6 large coals/pebbles on top of the simulated front (one in
each groove). Allow the coals/pebbles to rest on the support
shelf. Place 5 large coals/pebbles on the on the first tier of the
support shelf (Fig. 5).
Fig. 20
Place 6 small coals/pebbles
between the 6 large coals/pebbles
located on top of the simulated front.
Allow the coals/pebbles to rest on
the 5 large coals/pebbles on the first
tier.
Place 4 small coals/pebbles on top
of the 5 large coals/pebbles and
allow them to rest on the back tier of
the support shelf (Fig. 6).
Side View
To obtain the best visual appearance, it may be necessary to `slightly’ adjust the position of the coals.
If any of the coals or coal bed become damaged or lost, replacements MUST be obtained before further use.
ADDITIONAL COALS/PEBBLES MUST NOT BE USED
Page 11
18” Inset Taper 010710
2.6
CLEARANCE OFCOMBUSTION PRODUCTS
18” Inset
.
Relight the appliance and allow to run for five minutes with
the gas control in the `HIGH’ position. Check for
satisfactory clearance of combustion products by inserting
a lighted smoke match into the opening 100mm below the
top of the opening and 10mm in from the face of the
surround (Fig. 21).
Smoke match
to be positioned
100mm down
and 10mm in
from this point
Fig. 21
The majority of smoke must be drawn up into the flue. If
this does not occur, allow a further 10 minutes and repeat
the test. Should spillage still occur, examine the chimney
for fault and rectify.
The test should be repeated if an extractor fan or fan
powered flue appliance is fitted to the room. If there is a
connected room with an extractor fan, the test should be
repeated with all the connecting doors to that room
opened.
2.7
Smoke match
FRONT AND FRETS (REQUIREMENTS FOR VENTILATION)
Minimum ventilated area of front must be 60cm
2
The front and fret illustrated (Fig. 22), is a recommended
CROSSLEE front and fret. If an alternative front and fret
is to be used on the appliance, it is very important to
maintain the equivalent ventilation.
Fig. 22
Minimum ventilated area of fret must be 50cm
2.8
2
ADVISING THE CUSTOMER
Advise the customer on the following points:
The lighting and extinguishing procedures that are described in section 1.3.
They should read the `Instructions for Use’ section at the beginning of this booklet.
The appliance should be serviced at regular intervals and checked for spillage in accordance with the method described in section 2.6.
The curing effect of heating the coals will cause an initial odour. This is not harmful although additional ventilation (i.e. an opened window)
may be required until the odour has disappeared.
If the appliance is turned off or shuts off automatically, wait for at least three minutes before attempting to relight.
Page 12
18” Inset Taper 010710
Section 3 – Maintenance & Servicing
3.1
REMOVAL OF DEBRIS OR SOOT
18” Inset
Allow the appliance to cool for two to three hours before removing all of the fibre components for cleaning purposes. Once all the fibre is
removed, check that no debris is located in the burner holes of the appliance. If any debris is located, carefully remove any foreign matter
from the burner holes.
Any soot deposits or debris left on the fibre components may be removed by using a soft brush. Brush with the component held away from
your face so that you avoid inhaling the dust. CROSSLEE plc DOES NOT recommend the use of a normal vacuum cleaner, which may
blow dust back into the room.
To ensure that the release of fibres from these RCF articles is kept to a minimum, during installation and servicing, CROSSLEE
recommend that a HEPA filtered vacuum is used to remove any dust and soot accumulated in and around the appliance before and after
working. When replacing these articles, CROSSLEE recommend that they are NOT broken up, but are sealed in heavy duty polythene
bags and clearly labelled as RCF WASTE. This is not classified as hazardous waste and may be disposed of at a tipping site licensed for
the disposal of industrial waste. Protective clothing is not required when handling these articles although CROSSLEE recommend you
follow the normal hygiene rules of not smoking, eating or drinking in the work area and to always wash your hands before doing so.
3.2
SERVICING COMPONENTS BELOW THE BURNER
To gain access to the components below the burner, remove the fibre components and the burner unit from the firebox.
CLEANING OR REPLACING THE INJECTOR (Fig. 23).
™
™
™
™
Unscrew the compression nuts from the gas control to the injector.
Remove the formed pipe.
Unscrew the injector from the burner.
Replace in reverse order.
Fig. 23
REPLACING THE GAS CONTROL (Fig. 24).
™
™
™
™
™
Disconnect the two formed pipes from the gas control.
Disconnect the thermocouple from the gas control.
Remove the control knob.
Undo the retaining nut on the facia panel.
Replace in reverse order.
REPLACING THE PIEZO IGNITOR (Fig.25).
™
™
™
Fig. 25
Disconnect the HT lead from the piezo ignitor.
Retain the metal fixing nut with one finger and rotate piezo ignitor.
Replace in reverse order.
REPLACING THE MAIN BURNER & THERMOCOUPLE (Fig.26).
(Atmospheric sensing device)
™
™
™
™
™
™
™
™
™
Fig. 24
Fig. 26
Unscrew the two fastening nuts and washers from the rear of the burner unit.
Remove the stainless steel baffle and spacer plate.
Disconnect the formed pipe connecting the gas control and injector.
Unscrew the injector from the main burner
Unscrew the two fastening nuts and washers from the front of the burner unit.
Remove the main burner.
Unscrew the locknut, retaining the thermocouple.
Remove the thermocouple.
Replace in reverse order.
Page 13
18” Inset Taper 010710
18” Inset
16
15
13
18
4
9
10
12
17
1
5
3
14
2
6
8
11
7
Fig. 27
3.3
SPARE PARTS
PART DESCRIPTION
1
2
3
4
5
6
7
8,9
10
11
12
13
14
15
16
17
18
Aeromatix Burner (Natural Gas) (Manuf No AC03/211658 )
Piezo Ignitor c/w Steel Nut (Manuf No 66142/100)
087M Straight Injector (Manuf No 044-341-196-087M)
Ignition Lead (250mm)
Inlet Bundy
Gas Valve (Aero Burner) (Manuf. No MP21301B)
Control Knob
18” Facia Assembly (painted)
Restrictor Elbow c/w Pressure Test Point
Bundy Pipe Aero Burner
Heat Shield Raised Assy
Stainless Steel Baffle
Thermocouple c/w Nut (manuf No T100/927-400)
Electrode
Rear Support Frame
Front Retaining Bracket
Baffle Spacer Plate
Black Coal Bed (see section 1.4)
Black Simulated Front (see section 1.4)
Set of Ceramic Coals (see section 1.4) (11 Large & 10 small)
Set of Ceramic Pebbles (see section 1.4)(11 Large & 10 small)
CROSSLEE PART No
QUANTITY
0102 078 04311
40245
0102 078 04321
40244
0102 078 02391
0102 078 02431
0102 078 02791
0102 089 55831
0102 078 00041
0102 078 04331
0102 075 32541
0102 075 33201
0102 078 02351
0102 078 02421
0102 089 55781
0102 075 33451
0102 070 31551
0102 095 52521
0102 095 52531
0102 092 40331
0102 092 40341
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
Page 14
18” Inset Taper 010710
3.4
USEFUL TELEPHONE NUMBERS
In the event that you may require service, spares or technical information, please contact us at: Crosslee PLC
Halifax
West Yorkshire
HX3 8DE
Customer Service
Service Engineer (REPAIRCARE)
Telephone
01422 203963
0844 8797422*
Fax
01422 204767
*Calls cost 5p per minute from a UK BT landline. Charges from mobile and other network providers may vary.
Page 15
18” Inset Taper 010710