Empire Comfort Systems FAW-40-1SPP Owner`s manual

INSTALLATION INSTRUCTIONS
AND
OWNER'S MANUAL
FAN TYPE
VENTED
WALL FURNACE
MODEL
FAW-40-1SPP
FAW-40-1IP
WARNING: If the information in these instructions are not followed exactly, a fire or explosion may result causing property damage,
personal injury or loss of life.
— Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or
any other appliance.
Installer: Leave this manual with the appliance.
Consumer: Retain this manual for future reference.
WARNING: If not installed, operated and
maintained in accordance with the manufacturer's instructions, this product could expose you
to substances in fuel or from fuel combustion
which can cause death or serious illness.
— WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch; do not
use any phone in your building.
• Immediately call your gas supplier from a
neighbor’s phone. Follow the gas supplier’s instructions.
• If you cannot reach your gas supplier, call
the fire department.
— Installation and service must be performed
by a qualified installer, service agency or the
gas supplier.
Page 1
Introduction
Always consult your local Building Department regarding regulations, codes
or ordinances which apply to the installation of a vented wall furnace.
Instructions to Installer
1. Installer must leave instruction manual with owner after installation.
2. Installer must have owner fill out and mail warranty card supplied with
furnace.
3. Installer should show owner how to start and operate furnace and
thermostat.
Warning:
Any change to this furnace or its control can be dangerous. This
is a heating appliance and any panel, door or guard removed for
servicing an appliance must be replaced prior to operating the
appliance.
General Information
This series is design certified in accordance with American National
Standard / CSA Standard Z21.86 and CSA 2.32 by the Canadian Standards
Association, as a Fan Type Vented Wall Furnace and must be installed
according to these instructions.
Any alteration of the original design, installed other than as shown in
these instructions or use with a type of gas not shown on the rating plate
is the responsibility of the person and company making the change.
Important
All correspondence should refer to complete Model No., Serial No. and
type of gas.
Notice: During initial firing of this unit, its paint will bake out and smoke
will occur. To prevent triggering of smoke alarms, ventilate the room in
which the unit is installed.
Installation in Residential Garages
Gas utilization equipment in residential garages shall be installed so
that all burners and burner ignition devices are located not less than 18"
(457mm) above the floor.
Such equipment shall be located, or protected, so it is not subject to physical
damage by a moving vehicle.
Specifications
Model
FAW-40SPP
FAW-40IP
Input BTU/HR (KW/H)
40,000 (11.7)
40,000 (11.7)
Height
72 1/2" (84.1mm) 72 1/2" (184.1mm)
Width
14 1/8" (35.9mm) 14 1/8" (35.9mm)
Depth
10 3/8" (26.4mm) 10 3/8" (26.4mm)
Gas Inlet Pipe
1/2" (12.7mm)
1/2" (12.7mm)
Vent Collar Type B Oval
4" (101mm)
4" (101mm)
CFM
275
275
Accessories
SOR-1
Register, side outlet, fixed register
Side outlet, 10" (254mm)
SOK-1
maximum extension, fixed register
Rear outlet, 10" (254mm)
ROK-1
maximum extension, adjustable register
FVE-24
Vent enclosure, 24" (609mm)
[for rooms up to 96 1/2" 2451mm) in height]
Vent enclosure, 34" (86cm)
FVE-34
[for rooms up to 106 1/2" (2705mm) in height]
Vent enclosure, 46" (1168mm)
FVE-46
[for rooms up to 118 1/2" (3009mm) in height]
Oval-to-Round flue adapter kit 4" (102mm)
DV-648
Installation on Rugs and Tile
If this appliance is installed directly on carpeting, tile or other combustible
material other than wood flooring the appliance shall be installed on a metal
or wood panel extending the full width and depth of the appliance.
The base referred to above does not mean the fire-proof base as used on
wood stoves. The protection is for rugs that are extremely thick and light
colored tile.
THIS IS A HEATING APPLIANCE
DO NOT OPERATE THIS APPLIANCE WITHOUT FRONT PANELS INSTALLED.
• Due to high temperatures the appliance should be located out
of traffic and away from furniture and draperies.
• Children and adults should be alerted to the hazards of high
surface temperatures and should stay away to avoid burns or
clothing ignition.
• Young children should be carefully supervised when they are
in the same room as the appliance.
• Clothing or other flammable material should not be placed on
or near the appliance.
• Any safety screen or guard removed for servicing an appliance
must be replaced prior to operating the appliance.
• Keep burner and control compartment clean.
• Installation and repair should be done by a QUALIFIED SERVICE PERSON. The appliance should be inspected before
use and at least annually by a qualified service person. More
frequent cleaning may be required due to excessive lint from
carpeting, bedding materials, etc. It is imperative that control
compartments, burners and circulating air passageways of the
appliance be kept clean.
• DO NOT put anything around the furnace that will obstruct
Page 2
the flow of combustion and ventilation air.
• DO keep the appliance area clear and free from combustible
material, gasoline and other flammable vapors and liquids.
• DO examine venting system periodically and replace damaged
parts.
• DO make a periodic visual check of pilot and burners. Clean
and replace damaged parts.
• CAUTION: Pilot hole cover must be kept tightly closed during
operation.
• DO NOT use this heater if any part has been under water.
Immediately call a qualified service technician to inspect the
heater and to replace any part of the control system and any
gas control which has been under water.
• This furnace must not be connected to a chimney flue serving
a separate solid-fuel burning appliance.
•
IMPORTANT: This furnace has a washable permanent type
filter in the door which should be cleaned at least once per
year before the heating season. For dirty or high use areas
more frequent cleaning is required.
12427-7-1007
SAFETY INFORMATION FOR USERS OF LP-GAS
Propane (LP-Gas) is a flammable gas which can cause fires
and explosions. In its natural state, propane is odorless and
colorless. You may not know all the following safety precautions
which can protect both you and your family from an accident.
Read them carefully now, then review them point by point
with the members of your household. Someday when there
may not be a minute to lose, everyone's safety will depend on
knowing exactly what to do. If, after reading the following
information, you feel you still need more information, please
contact your gas supplier.
LP-GAS WARNING ODOR
If a gas leak happens, you should be able to smell the gas because of the odorant put in the LP-Gas.
That's your signal to go into immediate action!
•
Do not operate electric switches, light matches, use your
phone. Do not do anything that could ignite the gas.
•
Get everyone out of the building, vehicle, trailer, or area. Do
that IMMEDIATELY.
•
Close all gas tank or cylinder supply valves.
•
LP-Gas is heavier than air and may settle in low areas such
as basements. When you have reason to suspect a gas leak,
keep out of basements and other low areas. Stay out until
firefighters declare them to be safe.
•
Use your neighbor's phone and call a trained LP-Gas service
person and the fire department. Even though you may not
continue to smell gas, do not turn on the gas again. Do not
re-enter the building, vehicle, trailer, or area.
•
Finally, let the service man and firefighters check for escaped
gas. Have them air out the area before you return. Properly
trained LP-Gas service people should repair the leak, then
check and relight the gas appliance for you.
NO ODOR DETECTED - ODOR FADE
Some people cannot smell well. Some people cannot smell the
odor of the chemical stench put into the gas. You must find out
if you can smell the odorant in propane. Smoking can decrease
your ability to smell. Being around an odor for a time can affect
your sensitivity or ability to detect that odor. Sometimes other
odors in the area mask the gas odor. People may not smell the
gas odor or their minds are on something else. Thinking about
smelling a gas odor can make it easier to smell.
The odorant in LP-gas is colorless, and it can fade under some
circumstances. For example, if there is an underground leak, the
movement of the gas through soil can filter the odorant. Odorants
in LP-Gas also are subject to oxidation. This fading can occur if
there is rust inside the storage tank or in iron gas pipes.
The odorant in escaped gas can adsorb or absorb onto or into walls,
masonry and other materials and fabrics in a room. That will take
some of the odorant out of the gas, reducing its odor intensity.
LP-Gas may stratify in a closed area, and the odor intensity could
vary at different levels. Since it is heavier than air, there may be
more odor at lower levels. Always be sensitive to the slightest
gas odor. If you detect any odor, treat it as a serious leak. Immediately go into action as instructed earlier.
SOME POINTS TO REMEMBER
•
Learn to recognize the odor of LP-gas. Your local LP-Gas
Dealer can give you a "Scratch and Sniff" pamphlet. Use it
to find out what the propane odor smells like. If you suspect
that your LP-Gas has a weak or abnormal odor, call your
LP-Gas Dealer.
•
If you are not qualified, do not light pilot lights, perform service,
or make adjustments to appliances on the LP-Gas system. If
you are qualified, consciously think about the odor of LP-Gas
prior to and while lighting pilot lights or performing service
or making adjustments.
•
Sometimes a basement or a closed-up house has a musty
smell that can cover up the LP-Gas odor. Do not try to light
pilot lights, perform service, or make adjustments in an area
where the conditions are such that you may not detect the
odor if there has been a leak of LP-Gas.
•
Odor fade, due to oxidation by rust or adsorption on walls
of new cylinders and tanks, is possible. Therefore, people
should be particularly alert and careful when new tanks or
cylinders are placed in service. Odor fade can occur in new
tanks, or reinstalled old tanks, if they are filled and allowed
12427-7-1007
to set too long before refilling. Cylinders and tanks which
have been out of service for a time may develop internal rust
which will cause odor fade. If such conditions are suspected
to exist, a periodic sniff test of the gas is advisable. If you
have any question about the gas odor, call your LP-gas
dealer. A periodic sniff test of the LP-gas is a good safety
measure under any condition.
•
If, at any time, you do not smell the LP-Gas odorant and you
think you should, assume you have a leak. Then take the same
immediate action recommended above for the occasion when
you do detect the odorized LP-Gas.
•
If you experience a complete "gas out," (the container is under no vapor pressure), turn the tank valve off immediately.
If the container valve is left on, the container may draw in
some air through openings such as pilot light orifices. If this
occurs, some new internal rusting could occur. If the valve is
left open, then treat the container as a new tank. Always be
sure your container is under vapor pressure by turning it off
at the container before it goes completely empty or having it
refilled before it is completely empty.
Page 3
Ventilation and Combustion Air
WARNING: Danger of property damage, bodily injury or death,
this furnace and any other fuel burning appliance must be provided
with enough fresh air for proper combustion and ventilation of
flue gases. Most homes will require that outside air be supplied. Do
not draw air from a corrosive environment such as a workshop or
laundry room.
The requirements for providing air for combustion and ventilation are
listed in the National Fuel Gas Codes NFPA 54/ANSI Z223.1 (in Canada
- CAN/CGA B149).
Note: Air requirements for operation of exhaust fans, kitchen ventilation
systems, clothes dryers, fireplace and any other fuel burning or ventilating
equipment used in the space must be considered in determining combustion
air requirements.
Ventilation Air Openings and Ducts
In determining the free area needed consideration must be given to the
blocking effect of louvers, grills or screens protecting openings.
— If a screen is used to cover openings it must not be smaller than 1/4"
mesh.
— Use the free area of a louver or grill to determine the size opening
required to provide the free area specified. If the free area is not known
assume a 20% free area for wood and a 60% free area for a metal louver
or grill.
— Ducts must have the same cross sectional area as the free area of the
openings to which they connect.
— The minimum dimension of air ducts must not be less than 3 inches.
Installation in an Unconfined Space
An unconfined space is an area including all rooms not separated by doors
with a volume greater than 50 cubic feet per 1,000 Btuh of the combined
total input rates of all appliances which draw combustion air from that
space. For example, a space including a water heater rated at 40,000
Btuh input and a furnace rated at 40,000 Btuh requires a volume of 4,000
cubic feet (50 x (40 + 40) = 4,000) to be considered as unconfined. If the
space has an 8 ft. ceiling, the floor area of the space must be 500 sq. ft. In
general, particularly in older homes, a furnace installed in an unconfined
space will not require outside air for combustion. However in a "tight"
newly constructed home, outside air may be necessary to insure adequate
combustion.
Installation in a Confined Space
A confined space is an area with volume less than 50 cubic feet per 1,000
Btuh of the combined input rates of all appliances drawing combustion
air from that space. Small areas such as equipment rooms are confined
spaces. Furnaces installed in a confined space which supply heated air to
areas outside the space must draw return air from outside the space through
tightly sealed return air ducts. A confined space must have 2 openings into
the space for combustion air. One opening must be within 12 inches of the
ceiling and the other must be within 12 inches of the floor. The required
sizing of these openings is determined by whether inside or outside air
is used to support combustion, the method by which the air is brought
to the space (vertical or horizontal duct) and by the total input rate of all
appliances in the space. See Figure 1.
All Air From Inside — Confined Space
If combustion air is taken from the heated space the 2 openings must each
have a free area of at least one square inch per 1,000 Btuh of total input
of all appliances in the confined space but not less than 100 square inches
(645cm2) of free area.
For example: for a 40,000 Btuh furnace only in the confined space each
opening must be 100 square inches (645cm2) each of free area.
WARNING: Combustion air must not be drawn from a heated space
which includes exhaust fans, fireplaces or other devices that may
produce a negative pressure in the space.
opening
furnace
confined�
space
Figure 1
Outdoor Air
Outlet and inlet air can be brought into the confined space via openings
into a ventilated attic and ventilated crawl space.
a ttic ve ntila tion louvers
outle t air
furna ce
inle t a ir
cra wl s pace ve ntila tion louvers
Figure 2
Confined Space
Outdoor Air Using Vertical or Horizontal Ducts
If combustion air is taken from outdoors through vertical ducts, the
openings and ducts must have a minimum free area of one square inch
(6.5cm2) per 4,000 Btuh of total appliance input. In installations drawing
combustion air from a ventilated attic both air ducts must extend above
the attic insulation.
outlet air
furnace
vertical
inlet air ends one foot above floor
furnace
outlet air duct
inlet air duct
horizontal
Figure 3
If combustion air is taken from outdoors through horizontal ducts the
openings and ducts must have a minimum free area of one square inch
(6.5cm2) per 2,000 Btuh of total appliance input.
Page 4
12427-7-1007
Qualified Installing Agency
Installation and replacement of gas piping, gas utilization equipment or
accessories and repair and servicing of equipment shall be performed
only by a qualified agency. The term "qualified agency" means any
individual, firm, corporation or company which either in person or through
a representative is engaged in and is responsible for (a) the installation
or replacement of gas piping or (b) the connection, installation, repair or
servicing of equipment, who is experienced in such work, familiar with
all precautions required and has complied with all the requirements of the
authority having jurisdiction.
1. Type B-1 oval pipe or B-W vent pipe
2. Type B-1 oval elbows or B-W oval elbows
3. Single story type B-1 or (B-W) gas vents require a baseplate and
one pair of ceiling plate spacers.
4. Multi-story type B-1 or (B-W) gas vents require a baseplate, one
pair of ceiling plate spacers at the first floor ceiling and one pair
of fire stop spacers at each successive ceiling level.
Stud space around gas vents must be free of obstructions and building
paper.
The installation must conform with local codes or, in the absence of local
codes, with the National Fuel Gas Code, ANSI Z223.1/NFPA 54* Natural
and Propane Installation Code, CSA B149.1.
4” ROUND
*Available from the American National Standards Institute, Inc., 11 West 42nd St., New York,
N.Y. 10036.
Clearances
1. In selecting a location for installation, it is necessary to provide adequate
accessibility clearances for servicing and proper installation.
2. The FAW-40 can be attached to the wall or recessed into the wall up
to 9 1/2 inches (24.1cm) in depth. Note: Do not place combustible
header or material on top of unit when installed in wall. Maintain
3/4" minimum spacing above heater.
3. The wall in which the furnace is recessed has (0) zero (0mm) clearance
to the furnace sides.
4. When using side discharge registers, SOR-1 or SOK-1, the furnace
cannot be recessed into the wall.
5. Clearance to sidewall or combustible material is 4 inches (10.2cm).
6. Ceiling clearance is 4 inches (10.2cm).
7. Floor and rear wall clearance is (0) zero inches (0mm).
8. Clearance of 18 inches (46cm) is required to adjacent wall or combustible
material when flush mounted SOR-1, side outlet register is used.
Before Installing Consider The Following Venting
1. A chimney for residential-type or low-heat gas utilization equipment
shall extend at least 3 feet (914mm) above the highest point where it
passes through a roof of a building and at least 2 feet (610mm) higher
than any portion of building within a horizontal distance of 10 feet
(3m).
2. This furnace must not be connected to a chimney flue serving a separate
solid-fuel burning appliance.
3. Uninsulated Single-Wall Metal Pipe shall not be used outdoors in
cold climates for venting gas utilization equipment.
4. Attention! This Fan Type Vented Wall Furnace is equipped with a vent
safety switch. In the event of spillage of flue products due to improper
venting the vent safety switch will open, which results in the main
burners to "shut off".
Model No. FAW-40 may be vented as shown in Figure 4. The vent cap
termination must be at least 12 feet (3.7m) above the floor and must exhaust
to the outdoors.. Clearance to combustible construction is held by the fixed
spacers at 1 inch (25mm) with B-1 or (B-W) vent pipe. Installation must
conform to local codes.
A. 4" (102mm) Round (all parts purchase locally except Item 2)
1. Type B-1 round pipe
2. Part No. DV-648, 4" (102mm) oval-to-round flue adapter kit (see
accessories)
3. Single story type B-1 gas vents require a baseplate and one pair
of ceiling plate spacers.
4. Multi-story type B-1 gas vents require a baseplate, one pair of
ceiling plate spacers at the first floor ceiling and one pair of fire
stop spacers at each successive ceiling level.
B. 4" (102mm) Oval (all parts purchase locally)
1. Type B-1 oval pipe or B-W vent pipe
2. Single story type B-1 or (B-W) gas vents require a baseplate and
one pair of ceiling plate spacers.
3. Multi-story type B-1 or (B-W) gas vents require a baseplate, one
pair of ceiling plate spacers at the first floor ceiling and one pair
of fire stop spacers at each successive ceiling level.
VENT
ENCLOSURE
ADAPTER
WALL
BASEPLATE
A.
FRONT
SIDE
4” B-1 OVAL
BRACKET
BASEPLATE
B.
4” B-1 OVAL
4” 45 DEG.
OVAL ELBOWS
SPACER
BASEPLATE
C.
4” B-1 OVAL
SPACER
BASEPLATE
C.
Figure 4
C. 4" (102mm) Oval In-The-Wall (all parts purchase locally)
12427-7-1007
Page 5
(38mm) provided screws.
5. Attach outer boot to the cabinet side with (4) #8 x 1/4" (6mm) provided
screws.
6. Position and attach inner boot to inner shield with (4) #8 x 1/4" (6mm)
provided screws.
7. Place the register over the 6 3/4" (171mm) square opening with the
louvers positioned for the desired discharge direction and mark the
mounting holes using the register as a template.
8. Drill (2) 1/8" (3mm) diameter holes in the wall and attach the register
with (2) #10 x 1 1/2" (38mm) provided screws.
9. Installation of SOK-1 is completed.
4" MINIMUM TO COMBUSTIBLE�
WALL OR SURFACE
4" MINIMUM TO COMBUSTIBLE�
WALL OR SURFACE
WALL
18" MIN. CLEARANCE TO
WALL OR COMBUSTIBLE
SURFACE USING MODEL
SOR-1 SIDE REGISTER.
Figure 5
Use U.L. listed gas vent equipment when installing the FAW-40. For
vent pipe running through walls, roof, and within one (1) inch (25mm) of
combustible construction, use B-1 or (B-W) [one inch (25mm) clearance
to combustibles] vent pipe. Type B-2 x 4 or Type B-2 x 6 are to be used
in conjunction with a Listed fire stop spacer.
Be sure baseplate is attached to top of furnace before inserting unit into
recessed wall installation.
Installing Optional Side Outlets
Side outlet register, SOR-1 may be installed on one or both sides of the
furnace at the required clearances of 18 inches (457mm) to adjacent wall
or combustible material as shown in Figure 6.
1. Turn "OFF" all electric power to the furnace.
2. Remove the front panel from the furnace.
3. Remove the (2) #8 x 3/8" (9mm) screws that attach the inner shield
cover plate to the inner shield.
4. Scribe a line between the four dimples on the outer casing side to form
a square.
5. Drill a pilot hole within the scribed square on the outer casing. Remove
the sheet metal within the scribed square with a tin snips or comparable
tool. Attention! Do not cut the electrical wires located between the outer
casing and the inner shield.
6. Insert the 5" x 5" (127mm x 127mm) inner boot through the outer casing. Align the clearance holes on the inner boot with the screw holes
on the inner shield. Attach inner boot to inner shield with (2) # 8 x 3/8"
(9mm) screws removed in Step 3.
7. Place the register over the 5 1/2" (140mm) square opening with the
louvers set for the desired direction and mark the mounting holes using
the register as a template.
8. Drill (2) 1/8" diameter holes in cabinet side and attach the register with
(2) #10 x 1" (25mm) provided screws.
9. Installation of SOR-1 is completed.
Side outlet kit, SOK-1, 10" (254mm) boot assembly with register, for
warm air discharge into an adjoining room may be installed on either side
of the furnace at the required clearance of 4 inches (102mm) to adjacent
wall as shown in Figure 6.
To install SOK-1, please use Steps 1 through 5 in the SOR-1 instructions
for FAW-40 furnaces. Now, use the following Steps to complete installation of the SOK-1.
1. Using the inner and outer boots as hole templates, mark and drill (4)
1/8" (3mm) diameter holes in the inner shield and (4) 1/8" (3mm)
diameter holes in the cabinet side.
2. Locate and cut a 6 3/4" (171mm) square opening through wall.
3. Attach furnace to wall (see Attaching Furnace to Wall).
4. With furnace in place, after checking alignment of side outlet opening
in wall and furnace, place the 9 3/8" x 9 3/8" (238mm x 238mm) side
outlet wall plate over outer boot, pass the outer boot through the wall
and attach side wall plate to furnace side of wall with (2) #10 x 1 1/2"
Page 6
CLEARANCE FOR SIDE OUTLET KITS AND REAR REGISTER�
KIT TO ADJACENT WALL
TYPE B-1 OR
B-W OVAL�
VENT PIPE
UNIT CANNOT BE RECESSED�
WHEN SIDE REGISTERS ARE�
USED.
5 1/2"
5 1/2"
6 1/4"
10 1/4"
12"
WHEN SIDE REGISTERS ARE�
NOT USED UNIT MAY BE RECESSED�
UP TO 9 1/2"
12"
REAR REGISTER OPENING�
IN OUTER CABINET
Figure 6
Installing Optional Rear Outlet
Rear outlet kit, 10" (254mm) boot assembly with register, ROK-1 for
warm air discharge into an adjoining room.
Attention: Before furnace is attached to the wall, the wall opening for
the rear outlet must be cut, in addition to removal of the outer and inner
casing knockouts on furnace.
1. The wall opening measurements for the rear outlet are the
following.
A. From floor to bottom of wall opening is 10 11/16" (271mm).
B. From bottom of wall opening to top of wall opening is 8 1/2"
(216mm).
C. Wall opening width is 12 1/8" (308mm).
2. Scribe a line between the four dimples on the outer casing back to
form a square. Drill a pilot hole within the scribed square on the outer
casing back. Remove the sheet metal within the scribed square with
a tin snips or comparable tool.
3. Remove the (4) #8 x 3/8" (9mm) screws that attach the inner casing
close off plate to the inner casing.
4. Insert the privacy shield through the outer casing back and the inner
casing back. The privacy shield will be in front of the inner casing
back and behind the combustion chamber tubes. Align clearance
holes on privacy shield with screw holes on inner casing back. Attach
privacy shield to inner casing back with (2) #8 x 3/8" (9mm) provided.
Attention: The (2) #8 x 3/8" (9mm) screws must be inserted from
the front of the furnace.
5. Attach furnace to wall.
6. Align clearance holes on 8" x 12" (203mm x 305mm) boot with
screw holes on outer casing back and mark boot to be flush with wall
surface. Remove boot and cut to proper length.
12427-7-1007
7. Attach 8" x 12" (203mm x 305mm)boot to outer casing back with (6)
#8 x 3/8" (9mm) screws provided.
8. Align clearance holes on 6" x 10" (152mm x 254mm) duct with
screw holes on inner casing back and mark duct to be 2 1/4" (57mm)
shorter than 8" x 12" (203mm x 305mm) boot. Remove duct and cut
to proper length.
9. Attach 6" x 10" (152mm x 254mm) duct to inner casing back with
(4) #8 x 3/8" (9mm)screws removed in Step 3, 2 on top and 2 on
bottom.
10. Insert rear register into 8" x 12" (203mm x 305mm) boot. Attach rear
register to wall with (2) #10 x 1"(25mm) screws provided.
11. Installation of ROK-1 is completed.
Locating Furnace On Wall
The furnace is to be located on a wall. The furnace is 14 1/8" (35.9cm) in
width and can be recessed into the wall with typical stud spacing.
A template is provided in furnace carton for locating gas line connection.
Also, refer to Figure 7 for positioning the furnace on wall and for locating
gas line connection.
Locating Gas Supply
The gas line can enter the furnace either through the floor or wall. The gas
line opening should be made at this time. Location of the opening will be
determined by the position of floor joists and the valve and union used
for servicing. See Figure 7.
72 3 /4"
5. Place 7/8" (22mm) strain relief bushing around the cord of the 3'
(914mm) plug assembly. Insert 7/8" (22mm) strain relief bushing into
the 7/8" (22mm) hole in the side panel.
Attention! The 7/8" (22mm) strain relief bushing is located within the same
yellow envelope as the Installation Instructions and Owner's Manual.
Attaching Furnace to Wall
When attaching furnace to the wall remove that portion of baseboard and
molding on the wall which is behind the furnace. Attach furnace to wall,
at the outer casing top, with (2) toggle bolts provided and to floor, at the
outer casing bottom, with (2) #10 x 1 1/2" (38mm) screws provided.
Gas Supply
Check all local codes for requirements, especially for the size and type of
gas supply line required. On Natural gas lines less than 75' (22.9m) long,
use 1/2" (13mm) pipe; on longer runs, use 3/4" (19mm) iron pipe or equal.
On LP gas lines please consult LP gas supplier.
Installing a New Main Gas Cock
Each appliance should have its own manual gas cock.
A manual main gas cock should be located in the vicinity of the unit. Where
none exists, or where its size or location is not adequate, contact your local
authorized installer for installation or relocation.
Compounds used on threaded joints of gas piping shall be resistant to the
action of liquefied petroleum gases. The gas lines must be checked for
leaks by the installer. This should be done with a soap solution watching
for bubbles on all exposed connections, and if unexposed, a pressure test
should be made.
Never use an exposed flame to check for leaks. Appliance must be
disconnected from piping at inlet of control valve and pipe capped or
plugged for pressure test. Never pressure test with appliance connected;
control valve will sustain damage!
A gas valve and ground joint union should be installed in the gas line upstream
of the gas control to aid in servicing. It is required by the National Fuel Gas
Code that a drip line be installed near the gas inlet. This should consist of
a vertical length of pipe tee connected into the gas line that is capped on
the bottom in which condensation and foreign particles may collect.
14 3/8"
CUT OUT OP ENING FOR RE CE SSE D MO UNTING
ELECTRICAL WIRING HOLE
GAS LINE
HOLE 1 1/4 "
2 1 /8"
RECESS ED MOUNTING
LO CATION
4"
4"
8"
GAS LINE /ELECTRICAL OP ENINGS FOR�
RECESS ED AND SURFACE MO UNT
Figure 7
Locating Electric Supply
A 7/8" (22mm) diameter knockout is provided at the bottom of the left
and right side panels. A three-prong (grounding) plug assembly is located
within the control compartment (bottom) of the furnace. Please remove
7/8" (22mm) knockout from appropriate side panel when routing plug
assembly to an electrical outlet.
Installation of Three-prong (Grounding) Plug Assembly
1. Disconnect nylon cap on 3' (914mm) plug assembly from nylon plug
on wiring harness. Remove 3' (914mm) plug assembly from control
compartment (bottom) of the furnace.
2. Remove 7/8" (22mm) knockout from appropriate side panel.
3. Insert nylon cap on 3' (914mm) plug assembly into the 7/8" (22mm)
hole in the side panel.
4. Connect nylon cap on 3' (914mm) plug assembly to nylon plug on the
wiring harness.
12427-7-1007
Figure 8
Method of Installing a Tee Fitting Sediment Trap
The use of the following gas connectors is recommended:
— ANS Z21.24 Appliance Connectors of Corrugated Metal Tubing and
Fittings
— ANS Z21.45 Assembled Flexible Appliance Connectors of Other
Than All-Metal Construction
The above connectors may be used if acceptable by the authority having
jurisdiction.
Pressure Testing of the Gas Supply System
1. To check the inlet pressure to the gas valve, a 1/8" (3mm) N.P.T.
plugged tapping, accessible for test gauge connection, must be placed
immediately upstream of the gas supply connection to the appliance.
2. The appliance and its individual shutoff valve must be disconnected
from the gas supply piping system during any pressure testing of that
system at test pressures in excess of 1/2 psig (3.5 kPa).
3. The appliance must be isolated from the gas supply piping system by
closing its individual manual shutoff valve during any pressure testing
of the gas supply piping system at test pressures equal to or less than
1/2 psig (3.5 kPa).
Page 7
Attention! If one of the above procedures results in pressures in excess
of 1/2 psig (14" w.c.) (3.5 kPa) on the appliance gas valve, it will result
in a hazardous condition.
Checking Manifold Pressure
Both Propane and Natural gas valves have a built-in pressure regulator
in the gas valve. Natural gas models will have a manifold pressure of
approximately 4.0" w.c. (.996kPa) at the valve outlet with the inlet pressure
to the valve from a minimum of 5.0" w.c. (1.24kPa) for the purpose of
input adjustment to a maximum of 10.5" w.c. (2.615kPa). Propane gas
models will have a manifold pressure approximately 10.0" w.c. (2.49kPa)
at the valve outlet with the inlet pressure to the valve from a minimum of
11.0" w.c. (2.739kPa) for the purpose of input adjustment to a maximum
of 13.0" w.c. (3.237kPa).
A 1/8" (3mm) N.P.T. plugged tapping, accessible for test gauge connection,
is located on the outlet side of the gas control.
The built-in regulator comes on at approximately 1/4th pressure and full
on in 10 seconds.
them. Be sure there is no lint or foreign debris blocking the burner ports.
Reassemble using the same screws earlier removed and locate pilot in the
same position as before and noted above.
THERMOCOUPLE
BURNER
SPARK�
ELECTRODE
STANDING PILOT
THERMOCOUP LE
Piezo Pilot Ignitor Instructions
Depressing the red button completely causes a spark to occur at the pilot. This
is a substitute for a match which requires opening the pilot hole cover.
To light the pilot, it is important that the electrode be 1/8" (3mm) from the
thermocouple. The spark must occur at the point the burner flame hits the
thermocouple. The end of the electrode will be red hot with the pilot on.
On a new installation with air in the gas line, it is suggested that a match
be used. The match will light the pilot faster than the piezo under this
condition.
Proper Pilot Flame
The correct pilot flame (Figure 10) will be blue, extending past the
thermocouple. The flame will surround the thermocouple just below the
tip.
Natural gas pilots require adjusting when the inlet gas pressure is above 5"
w.c. (1.245kPa). Remove the pilot cover screw on the control valve (Figure
9), and turn the adjustment screw clockwise to reduce flame. Replace pilot
cover screw to eliminate gas leakage.
LP gas (propane) will not require adjustment.
After use, cleaning may be required for the proper flame.
Proper Main Burner Flame
The correct flame will be a short, blue inner flame with a much larger, light
blue, outer flame. The burner does not have a primary air adjustment. The
flame will be correct if the factory-set pressure and orifice opening are
used. After the furnace has been operating, the burner ports may be blocked
by foreign matter carried in by combustion air. Therefore, cleaning of the
burner may be needed for proper flame.
To clean burner port disconnect the gas supply to the valve, and remove
the screws fastening the burner door. After removing the burner door from
the burner box, remove each main burner. Pilot mounting bracket will
need to be unscrewed and moved out of the way to remove all burners.
Burners can be blown out using compressed air or by blowing through
Page 8
P ILOT S HIELD
S PAR K�
ELEC TR ODE
P ILOT LOC ATION END VIEW
Figure 9
High Altitudes
For altitudes/elevations above 2,000 feet (610m), input ratings should
be reduced at the rate of 4 percent for each 1,000 feet (305m) above sea
level. For Canadian high altitude applications, this appliance is suitable
for installation at elevations between 0 feet (0m) and 4,500 feet (1,372m)
without change.
PILOT
S TANDING P ILOT S HOWN
3/8" TO 1/2"�
PILOT FLAME
GROUND�
ELECTRODE
BURNER
PILOT
HOT SURFACE�
IGNITOR
FLAME�
ROD
IP-MODEL PILOT
Figure 10
Figure 11
Cleaning Combustion (Exchanger) Assembly
A QUALIFIED SERVICE PERSON should remove the combustion
(exchanger) assembly and flue baffles. Apply air pressure to the inside
of the combustion (exchanger) assembly and flue baffles in order to clear
all passageways.
Oiling the Motor
The fan motor should be cleaned and oiled once each heating season. Oil
holes are located on the top at each end of the motor. Use a few drops of
12427-7-1007
#10 motor oil. To clean the motor, blow air through its ventilation openings
with a vacuum cleaner or low pressure air source.
Wiring
The appliance, when installed, must be electrically grounded in accordance
with local codes or, in the absence of local codes, with the National Electrical
Code, ANSI/NFPA 70 or Canadian Electrical Code, CSA C22.1, if an
external electrical source is utilized. This appliance is equipped with a
three-prong [grounding] plug for your protection against shock hazard
and should be plugged directly into a properly grounded three-prong
receptacle. Do not cut or remove the grounding prong from this plug.
For an ungrounded receptacle, an adapter, which has two prongs and a wire
for grounding, can be purchased, plugged into the ungrounded receptacle
and its wire connected to the receptacle mounting screw. With this wire
completing the ground, the appliance cord plug can be plugged into the
adapter and be electrically grounded. A 7/8" (22mm) hole is provided in
the junction box for use with a conduit connector if local codes require
this type of protection.
To reset the manual reset vent safety switch:
1. Remove front panel.
2. Depress manual reset button. The manual reset vent safety switch is
located on the draft diverter.
3. Replace front panel.
If the manual reset vent safety switch continues to "shut off" the gas flow
to the main burners a qualified service person must be contacted to inspect
for improper venting, blockage in the vent pipe or the manual reset vent
safety switch for being defective.
Thermostat Installation
The thermostat should be installed in the same room as the furnace 4'
(1.2m) to 5' (1.5m) above the floor and away from another heat source
(cooking stove, hot water heater, etc.) including walls and doorways
with a heat source in an adjoining room. Do Not Install Thermostat on
Outside Wall.
Insulated Vent Enclosure
Vented wall furnaces installed in buildings with flat roofs can have poor
venting. The cold vent pipe will have a delay in proper venting and cause
the wall furnace to shut "OFF" by the vent safety switch. To prevent
delayed venting as well as condensation of flue products an insulated vent
enclosure is recommended.
Use type B vent pipe and maintain at least a one inch (25mm) clearance
to combustibles.
Use metal thimble to protect vent pipe as it passes through
combustibles.
Figure 13
FLUE C ONNECTOR
VENT LIMIT S WITCH
DR AFT DIVER TER
FAN
Figure 12
Vent Safety Shutoff System
This appliance must be properly connected to a venting system. This
appliance is equipped with a vent safety shutoff system.
Warning: Operation of this wall furnace when not connected to
a properly installed and maintained venting system or tampering
with the vent safety shutoff system can result in carbon monoxide
(CO) poisoning and possible death.
This furnace is equipped with a manual reset vent safety switch. The
manual reset vent safety switch will cause gas flow to the main burners
to "shut off" due to improper venting or a blocked flue.
12427-7-1007
LIMIT
S WITC
H
FAN
SWITCH
FANLIMIT
S WITCSWITCH
H
BURNER BOX
P IEZO�
IGNITOR
GAS VALVE
J UNC TION BOX-�
TR ANS FOR MER
Figure 14
Page 9
SERVICE AND MAINTENANCE SUGGESTIONS
CALL SERVICEMAN
GENERAL: All furnaces have been fire-tested to check for proper operation.
This includes, main burner flame, pilot flame, fan operation, fan control,
limit control and automatic valve operation. If the furnace fails to function
on initial installation, it is advisable to re-check the following:
1. 115 volts to the junction box.
2. Inlet gas pressure.
3. The 24 volt system.
4. Type of gas being used and that shown on the rating label.
The Service Department at Empire Comfort Systems, Inc. may be contacted
to assist in servicing furnace.
Standing Pilot Model
Servicing the Pilot and Main Burners, Pilot Orifice, Thermocouple,
and Main Burner Orifices: Disconnect the gas supply at the inlet to the
control valve. Then remove the burner door to gain access to the above
listed components.
Spark Igniter Does Not Light Pilot: With air in the gas line, such as when
the furnace is first installed or was off all summer, the pilot flame may
be too lean to ignite on the first few trials. Turn the control valve knob to
pilot position and depress the red reset button. Holding the button down
continually to bleed the line;.
Pilot Flame Adjustment
The pilot flame should envelop 3/8 to 1/2 inch (10 to 13mm) of the tip of
the flame rod. See Figure 10.
To adjust:
1. Remove the pilot adjustment cover screw.
2. Turn the inner adjustment screw clockwise
to decrease or
counterclockwise
to increase pilot flame. Pilot adjustment
is shipped at full flow rate. Turn the inner adjustment screw clockwise
if the inlet pressure is too high.
3. Replace the cover screw after the adjustment to prevent gas leakage.
P RES S URE REGULATOR�
ADJ US TMENT-UNDER C AP �
S CR EW
OUTLET P R ES S UR E TAP
P ILOT ADJ US TMENT-�
UNDER CAP S C REW
INLET P RES S URE TAP
GAS F LOW
IGNITOR
P ILOT OUTLET
OFF ON
C ONTROL
IGNITOR-P ILOT AS S Y.
If Electrode Does Not Produce Spark:
1. Check wire connections.
2. Check gap for pilot burner to the electrode tip. Should be between
1/8" (3mm) and 3/16" (5mm). Electrode wire and tip must be more
than 1/4" (6mm) away from all other metal components.
If Pilot Does Not Light By Any Means:
1. Check valve knob for being in the "Pilot" position.
2. Check pilot adjustment for being full open (counterclockwise to
open).
3. If gas is available in the supply tubing, the pilot orifice and/or pilot
burner is probably restricted by a spider web. Clean pilot assembly
and relight.
If Pilot Does Not Remain On After Releasing Knob:
1. Follow instructions and hold button down longer and harder.
2. Determine if pilot flame extends past thermocouple; if not, adjust
input or clean pilot burner.
3. Replace thermocouple if millivolts read less than 15 millivolts.
Main Gas Valve Does Not Open When Thermostat Is Turned To On:
1. Check for 24 volts to valve by removing one wire and touching to the
SAME TERMINAL it was on. Terminal should have a light spark.
DO NOT SHORT ACROSS TERMINALS, AS IT WILL BURN
OUT THE WALL THERMOSTAT.
2. Thermostat wires at the wall may be shorted, so check for a faulty
thermostat.
3. To check for line voltage to furnace, remove front panel and short
across two-terminal fan control to allow fan to operate (Figure 14).
CAUTION: Label all wires prior to disconnection when servicing
controls. Wiring errors can cause improper and dangerous operation.
Verify proper operation after servicing.
WIR ING
IGNITOR
1. Use lighter rod to light pilot with a match.
2. Use the piezo ignitor at 30 second intervals until it lights.
TO 24 V. THERMOS TAT
C ONTROL
TO 24 V. COMMON ON TRANS FOR MER
TO 24 V."HOT" ON TR ANS F ORMER
I P-MODEL GAS VALVE AND WIRING
L2 NEUTRAL
L1 "HOT"
120 VAC
MOTOR
FAN�
SWITCH
120VAC
40 VA TRANSFORMER
VALVE CONTROL�
CONNECTOR
24 VAC
LIMIT�
CONTROL
THERMOSTAT
VENT SAFETY�
LIMIT
HONEYWELL IP�
SMART VALVE
LADDER WIRING DIAGRAM-IP VALVE
Figure 15
IP-Model Pilot
This heater is using a Honeywell "Smart Valve" system for intermittent
pilot ignition.
On a call for heat by the thermostat this control turns on a 24 volt mini
hot surface ignitor which lights a pilot that in turn lights the main burner.
The gas valve used in this system is a step opening which opens at a lower
pressure for ignition and then steps to a full inlet pressure of 4" H2O pressure
on Natural gas and 10" H20 pressure on LP gas.
Page 10
12427-7-1007
STANDING PILOT MODEL
FOR YOUR SAFETY READ BEFORE LIGHTING
WARNING: If you do not follow these instructions exactly, a fire or explosion may result
causing property damage, personal injury or loss of life.
A. This appliance has a pilot which must be lighted by
hand. When lighting the pilot, follow these instructions
exactly.
B. BEFORE LIGHTING smell all around the appliance
area for gas. Be sure to smell next to the floor because
some gas is heavier than air and will settle on the floor.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch;
do not use any phone in your building.
• Immediately call your gas supplier from a neighbor's
phone. Follow the gas supplier's instructions.
• If you cannot reach your gas supplier, call the fire
department.
C. Use only your hand to push in or turn the gas control
knob. Never use tools. If the knob will not push in or
turn by hand, don't try to repair it; call a qualified
service technician. Force or attempted repair may
result in a fire or explosion.
D. Do not use this appliance if any part has been under
water. Immediately call a qualified service technician
to inspect the appliance and to replace any part of the
control system and any gas control which has been
under water.
LIGHTING INSTRUCTIONS
1. S T O P !
above.
Read the safety information
tubes behind the pilot access cover.
9. Tu r n g a s c o n t ro l k n o b c o u n t e rc l o c k w i s e
2. Set the thermostat to lowest setting.
3. Turn off all electric power to the appliance.
4. Remove control access panel (lower front
panel).
5. Turn gas control knob clockwise
to "OFF."
to "PILOT."
10. Push and hold red reset button down completely and repeatedly push the ignitor button until the
pilot burner is lit. Pilot may also be lit with a match.
Continue to hold the red reset button down for about
one (1) minute after the pilot is lit. Release button and
it will pop back up. Pilot should remain lit. If it goes
out, repeat steps 5 through 10.
• If button does not pop up when released, stop and
immediately call a qualified service technician or
gas supplier.
6. Wait ten (10) minutes
to clear out any gas.
Then smell for gas, including near the floor. If you smell
gas, STOP! Follow "B" in the safety information above.
If you don't smell gas, go to the next step.
7. Remove the pilot access cover located on the
combustion chamber.
8. Find pilot - follow metal tube
from gas control. The pilot is
located between the two burner
• If the pilot will not stay lit after several tries,
turn the gas control knob to "OFF" and call your
service technician or gas supplier.
11. Replace pilot access cover.
12. Turn gas control knob counterclockwise
to "ON."
13. Replace control access panel (lower front
panel).
14. Turn on all electric power to the appliance.
15. Set thermostat to desired setting.
TO TURN OFF GAS TO APPLIANCE
1. Set the thermostat to lowest setting.
panel).
2. Turn off all electric power to appliance if
service is to be performed .
4. Push in gas control knob slightly and turn
clockwise
to "OFF." Do not force.
3. Remove
5. Replace control
panel).
12427-7-1007
control
access panel
(lower front
access panel
(lower front
Page 11
INTERMITTENT PILOT (IP) MODEL
FOR YOUR SAFETY READ BEFORE OPERATING
WARNING: If you do not follow these instructions exactly, a fire or explosion may result
causing property damage, personal injury or loss of life.
A. This appliance is equipped with an ignition device which
automatically lights the pilot.
Do not try to light the pilot by hand.
B. BEFORE OPERATING smell all around the appliance area for gas. Be sure to smell next to the floor
because some gas is heavier than air and will settle on
the floor.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch;
do not use any phone in your building.
• Immediately call your gas supplier from a neighbor's
phone. Follow the gas supplier's instructions.
• If you cannot reach your gas supplier, call the fire
department.
C. Use only your hand to slide the gas control knob.
Never use tools. Force or attempted repair may result
in a fire or explosion.
D. Do not use this appliance if any part has been under
water. Immediately call a qualified service technician
to inspect the appliance and to replace any part of
the control system and any gas control which has
been under water.
OPERATING INSTRUCTIONS
1. S T O P !
above.
Read the safety information
2. Set the thermostat to lowest setting.
3. Turn off all electric power to the appliance.
4. This appliance is equipped with an ignition
device which automatically lights the pilot. Do not try
to light the pilot by hand.
5. Remove front panel door.
6. Slide gas control switch to "OFF."
7. Wait ten (10) minutes
to clear out any gas.
Then smell for gas, including near the floor. If you smell
gas, STOP! Follow "B" in the safety information above.
If you don't smell gas, go to the next step.
8. Slide gas control switch to "ON".
9. Replace front panel door.
10. Turn on all electric power to the appliance.
11. Set thermostat to desired setting.
GAS FLOW
IGNITOR
OF F ON
12. If the appliance will not operate, follow the instructions
"TO TURN OFF GAS TO APPLIANCE" and call your
service technician or gas supplier.
CONTR OL
GAS VALVE S HOWN IN OFF P OS ITION
HONEYWELL IP S MART VALVE
TO TURN OFF GAS TO APPLIANCE
1. Set the thermostat to lowest setting.
4. Slide gas control switch to "OFF."
2. Turn off all electric power to the appliance
if service is to be performed.
5. Replace front panel door.
3. Remove front panel door.
Page 12
12427-7-1007
SEQUENCE OF OPERATION
Apply 24 VAC
To Appliance
START
Thermostat
Calls for Heat
5 Minute Retry Delay
Flame Signal
Detected
YES
Pilot Valve Ignition OFF
Wait for Flame Signal to
Disappear


NO
System Check
Internal Check
OK
NO
YES
Trial for
Ignition


Pilot Valve Opens
Ignitor Powered
Pilot Light and Flame is
Sensed During Trial For
Ignition (1)
NO


Pilot Valve Closes
Ignition OFF
YES
Main Burner
Operation


3 Second Flame Recycle
Delay
Ignitor OFF
Main Valve Opens
Flame Signal
Lost?
YES
Main Pilot
Valves Close
NO
Thermostat Call for Heat
Ends
Flame Lost More
Than 5 Times in
One Call for Heat
NO
END
Main Pilot Valves
Close
YES
(1) Ignitor will turn OFF about 30 seconds into the trial for ignition if the pilot flame has not lit. It will turn back ON for the final 30 seconds
of the 90 second trial for ignition. The pilot valve will be energized during the entire trial for ignition. This is normal operation for this gas
ignition system.
12427-7-1007
Page 13
START
 Turn OFF Gas Supply
 Disconnect System Control
Harness
 Set Thermostat to Call for
Heat
Check for Proper Voltage at
Control Harness (See Inset A Voltage Should be 24V
Between Thermostat and 24V
Common, and 24V Between
24V Common and 24V Hot.)
IP SYSTEM TROUBLESHOOTING SEQUENCE
SmartValveTM System Troubleshooting Sequence
Note: Before Troubleshooting, Become Familiar
with the Sequence of Operation
24 Volt
Common
NO
Plug Harness into SmartValve
Control
Wait for Internal Check Delay
(SV9501)
NO
Check
Unplug Pilot Burner Cable.
Measure Voltage at SmartValue HSI
Element Output (See Inset B) 24V
Nominal
End View
of Control
Harness
Connector
EFT
Output
24 Volt
Hot
24
Volts
INSET B
 Line Voltage Power
 Low Voltage Transformer
 Limit Controller
 Thermostat
 Wiring
HSI
Terminals
NO
Replace SmartValve Control
Reconnect Pilot Burner Cable
Replace Igniter/Flame Rod
Assembly
Note: Igniter Will Cycle OFF
and Back ON Once During the
90 Second Ignition Trial
Reconnect Pilot Burner Cable
YES
 Turn On Gas Supply
 Pilot Burner Lights
24 Volt
Thermostat
24
Volts
YES
Igniter Warms UP and Glows
Red
INSET A
NO
Check that Pilot Gas is Flowing
Wait to Assure Pilot Gas Tubing is
Purged.
Measure Voltage Between 24V Hot
and 24V Common Leads to
SmartValve Control. Must Measure
at Least 19.5 VAC with Igniter
Powered. See Inset A to Identify
Proper Lead. This Check Must be
Done with the SmartValve Control
Connected and Igniter Powered.
YES
NO
NO
Replace SmartValve Control
Check Transformer and Line Volt
Supply
Replace Igniter/Flame Rod
Assembly
Check that Pilot Flame Makes
Main Valve Opens and
Main Burner Lights
YES
System is Okay
Page 14
NO
Good Contact with Pilot Burner
Flame Rod
Check for Good Electrical
Connection Through the Pilot
Tubing
If Both of the Above are Good,
Replace Igniter/Flame Rod
Cycle Thermostat OFF and Back
ON
Main Burner Lights
NO
Replace SmartValve Control
12427-7-1007
PLEASE NOTE: When ordering parts, it is very important that part number and description of part coincide.
INDEX
NO.
PART
NUMBER
1
2
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
WFA-115
DV-1247
15668
R-3165
DV-1204
DV-1203
DV-1205
DV-1248
DV-1231
DV-1250
DV-1234
DV-1225
R-3177
R-3161
R-3166
DV-1246
R-1536
R-1499
18
R-1454
19
20
R-3164
DV-1251
21
22
23
R-6176
R-3176
DV-1253
24
24
25
26
27
DV-1254
15669
R-3163
R-3162
DV-1252
28
29
30
30
31
31
32
33
34
35
35
36
36
DV-1256
DV-1235
R-3232
R-3233
P-88-51
P-88-60
DV-1236
DV-1258
P-112
R-1109
R-9502
R-5655
R-2148
DESCRIPTION
GASKET - HEADER
TOP PLATE (USA)
TOP PLATE (CANADA)
DOOR CLIP (2 REQUIRED)
CASING SIDE - RIGHT
CASING BACK
CASING SIDE - LEFT
AIR DROP (INCLUDES NO. 54)
TURBULATOR (3 REQUIRED)
DIVIDER PLATE
OUTLET BOX
OUTLET BOX COVER
VENT SAFETY SWITCH
FAN BLADE
FAN MOTOR
MOTOR MOUNTING BRACKET
BUSHING (5 REQUIRED)
RUBBER GROMMET
(4 REQUIRED)
BRASS BUSHING
(4 REQUIRED)
DOOR CLIP (2 REQUIRED)
INNER SHIELD - RIGHT (INCLUDES
NO. 23)
FAN CONTROL SWITCH
LIMIT SWITCH
INNER SHIELD COVER PLATE (2
REQUIRED)
INNER SHIELD FRONT (USA)
INNER SHIELD FRONT (CANADA)
FILTER RETAINER
FILTER
INNER SHIELD -LEFT (INCLUDES
NO. 23)
EXCHANGER ASSEMBLY
PILOT BRACKET (IP ONLY)
PILOT - NAT (IP ONLY)
PILOT - LPG (IP ONLY)
ORIFICE - NAT (3 REQUIRED)
ORIFICE - LPG (3 REQUIRED)
MANIFOLD
FRONT PANEL
MANIFOLD UNION
BUSHING (3/8 x 1/2)
BUSHING (3/8 x 3/4) - NAT (IP ONLY)
GAS VALVE - LPG (SPP ONLY)
GAS VALVE - NAT (SPP ONLY)
INDEX
NO.
PART
NUMBER
36
36
37
38
39
R-3170
R-3171
R-2708
FF-160
DV-1318
40
DV-1242
41
42
43
DV-1237
M-148
GWT-168
44
GWT-169
45
46
47
R-3031
DV-1239
UH-452
47
UH-810
48
48
49
50
51
52
53
54
55
56
56
57
58
R-1995
R-998
UH-451
DV-572
DV-1260
R-1410
R-690
R-1515
DV-1215
R-3034
R-3035
GWT-021
R-3180
59
R-2256
60
NOT SHOWN
NOT SHOWN
NOT SHOWN
NOT SHOWN
NOT SHOWN
NOT SHOWN
NOT SHOWN
NOT SHOWN
R-6389
DV-1261
R-1081
R-1089
R-1233
R-3265
R-3172
R-3173
R-1587C
DESCRIPTION
GAS VALVE - NAT (IP ONLY)
GAS VALVE - LPG (IP ONLY)
PIEZO IGNITOR (SPP ONLY)
PIEZO BRACKET (SPP ONLY)
OBSERVATION HOLE COVER
PLATE
BURNER COMPARTMENT FRONT
(SPP ONLY)
BURNER COMPARTMENT BODY
MANIFOLD GASKET
AIR SHUTTER FRONT
(LPG ONLY)
AIR SHUTTER REAR
(LPG ONLY)
BURNER (3 REQUIRED)
BURNER BRACKET
TRANSFORMER MOUNTING
BRACKET (IP ONLY)
TRANSFORMER MOUNTING
BRACKET (SPP ONLY)
TRANSFORMER (SPP ONLY)
TRANSFORMER (IP ONLY)
JUNCTION BOX COVER
JUNCTION BOX
COVER PLATE - AIR DROP
BUSHING
CORD SET
BUSHING
BOTTOM PLATE
PILOT - NAT (SPP ONLY)
PILOT - LPG (SPP ONLY)
PILOT BRACKET (SPP ONLY)
ELECTRODE AND WIRE
(SPP ONLY)
THERMOCOUPLE -18"
(SPP ONLY)
WALL THERMOSTAT - 24 VOLT
PILOT TUBING
PILOT ORIFICE - NAT (SPP ONLY)
PILOT ORIFICE - LPG (SPP ONLY)
PILOT ORIFICE - NAT (IP ONLY)
PILOT ORIFICE - LPG (IP ONLY)
WIRE HARNESS (SPP ONLY)
WIRE HARNESS (IP ONLY)
VENT SAFETY WIRE ASSEMBLY
USE ONLY MANUFACTURER'S REPLACEMENT PARTS. USE OF ANY OTHER PARTS COULD CAUSE INJURY OR DEATH.
How To Order Repair Parts.
Parts can be ordered only through your service person or dealer. For best results, the service person or dealer should order parts through the distributor. Parts can be shipped directly to the service person/dealer.
All parts listed in the Parts List have a Part Number. When ordering parts, first obtain the Model Number from the name plate on your equipment.
Then determine the Part Number (not the Index Number) and the Description of each part from the following appropriate illustration and list. Be sure
to give all this information.
Furnace Model Number
Part Description
Furnace Serial Number
Part Number
Type of Gas (Propane or Natural)
Do not order bolts, screws, washers or nuts. They are standard hardware items and can be purchased at any local hardware store.
Shipments contingent upon strikes, fires and all causes beyond our control.
12427-7-1007
Empire Comfort Systems, Inc. Nine Eighteen Freeburg Ave.
Belleville, Illinois 62222-0529
Page 15
Page 16
12427-7-1007
SERVICE NOTES
12427-7-1007
Page 17
SERVICE NOTES
Page 18
12427-7-1007
SERVICE NOTES
12427-7-1007
Page 19
Empire Comfort Systems, Inc.
918 Freeburg Ave. Belleville, IL 62220
PH: 618-233-7420 or 800-851-3153
FAX: 618-233-7097 or 800-443-8648
info@empirecomfort.com
www.empirecomfort.com
Page 20
12427-7-1007