Bosch GSS 140 A Professional Operating instructions

Português - BR | 1
GSS 140 A Professional
pt Manual de instruções
es Instrucciones de servicio
en Operating instructions
F 000 622 340 | 06.2011
Bosch Power Tools
2 4|
7
1
6
2
5
8
3
4
GSS 140 A
Professional
A
B
C
4
4
3
5 6
2
3
1
5
3
4
2 609 140 834 | (10.12.10)
F 000 622 340 | 06.2011
Bosch Power Tools
Bosch Power Tools
5|
3
D1
D2
10
1
1
2
1
9
D3
D4
11
1
E
F
13
12
9
14
2 609 140 834 | (10.12.10)
F 000 622 340 | 06.2011
Bosch Power Tools
Bosch Power Tools
14 | English
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
1. Work area safety
a) Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
b) Do not operate power tools in explosive atmospheres,
such as in the presence of flammable liquids, gases
or dust. Power tools create sparks which may ignite the
dust or fumes.
c) Keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.
2. Electrical safety
a) Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs with
earthed (grounded) power tools. Unmodified plugs and
matching outlets will reduce risk of electric shock.
b) Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock
if your body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
d) Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges and moving
parts. Damaged or entangled cords increase the risk of
electric shock.
e) When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a
cord suitable for outdoor use reduces the risk of electric
shock.
f) If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.
3. Personal safety
a) Stay alert, watch what you are doing and use
common sense when operating a power tool. Do not
use a power tool while you are tired or under the
influence of drugs, alcohol or medication. A moment
of inattention while operating power tools may result in
serious personal injury.
b) Use personal protective equipment. Always wear eye
protection. Protective equipment such as dust mask,
non-skid safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce personal
injuries.
c) Prevent unintentional starting. Ensure the switch is
in the off-position before connecting to power source
and/or battery pack, picking up or carrying the tool.
Carrying power tools with your finger on the switch or
energising power tools that have the switch on invites
accidents.
F 000 622 340 | 06.2011
d) Remove any adjusting key or wrench before turning the
power tool on. A wrench or a key left attached to a rotating
part of the power tool may result in personal injury.
e) Do not overreach. Keep proper footing and balance at
all times. This enables better control of the power tool in
unexpected situations.
f) Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long hair
can be caught in moving parts.
g) If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection
can reduce dust-related hazards.
h) Use ear protectors. Exposure to noise can cause hearing
loss.
4. Power tool use and care
a) Do not force the power tool. Use the correct power
tool for your application. The correct power tool will
do the job better and safer at the rate for which it was
designed.
b) Do not use the power tool if the switch does not turn it
on and off. Any power tool that cannot be controlled with
the switch is dangerous and must be repaired.
c) Disconnect the plug from the power source and/or the
battery pack from the power tool before making any
adjustments, changing accessories, or storing power
tools. Such preventive safety measures reduce the risk of
starting the power tool accidentally.
d) Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool
or these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tool’s
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f) Keep cutting tools sharp and clean. Properly maintained
cutting tools with sharp cutting edges are less likely to
bind and are easier to control.
g) Use the power tool, accessories and tool bits etc.
in accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
5. Service
a) Have your power tool serviced by a qualified repair
person using only identical replacement parts.
This will ensure that the safety of the power tool is
maintained.
b) In case of consuming of the carbon brushes to send
the tool by assistance authorized technique for
substitution. Carbon brushes are of specify them cause
damages to the motor of the tool.
Bosch Power Tools
English | 15
c) If the power cord is damaged, the power cord shall be
replaced by manufacturer, service or qualified person to
avoid the risk of electrical shock.
Safety Warnings for Sander
►► Use the machine only for dry sanding. Penetration of
water into the machine increases the risk of an electric
shock.
►► Caution, fire hazard! Avoid overheating the
object being sanded as well as the sander. Always
empty the dust collector before taking breaks. In
unfavourable conditions, e. g., when sparks emit from
sanding metals, sanding debris in the dust bag, micro
filter or paper sack (or in the filter sack or filter of the
vacuum cleaner) can self-ignite. Particularly when
mixed with remainders of varnish, polyurethane or other
chemical materials and when the sanding debris is hot
after long periods of working.
►► Secure the workpiece. A workpiece clamped with
clamping devices or in a vice is held more secure than
by hand.
Products sold in GB only: Your product is fitted with an
BS 1363/A approved electric plug with internal fuse (ASTA
approved to BS 1362).
If the plug is not suitable for your socket outlets, it should
be cut off and an appropriate plug fitted in its place by an
authorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
Products sold in AUS and NZ only: Use a residual current
device (RCD) with a rated residual current of 30 mA or less.
Functional Description
Read all safety warnings and all
instructions. Failure to follow the warnings
and instructions may result in electric shock,
fire and/or serious injury. While reading the
operating instructions, unfold the graphics
page for the machine and leave it open.
Intended Use
The machine is intended for dry sanding of wood, plastic,
filler and coated surfaces.
Product Features
The numbering of the product features refers to
the illustration of the machine on the graphics page.
1
2
3
4
5
6
Dust box, complete (Microfilter System)*
Sanding plate
Sanding-sheet clamp
Sanding sheet*
Release button for front clamping bracket
Front clamping bracket
F 000 622 340 | 06.2011
7 On/Off switch
8 Handle (insulated gripping surface)
9 Extraction outlet
10 Latching lever for dust box*
11 Filter element (Microfilter System)*
12 Extraction adapter*
13 Vacuum hose*
14 Perforating tool*
*Accessories shown or described are not part of the standard
delivery scope of the product. A complete overview of accessories
can be found in our accessories program.
Technical Data
Orbital sander
GSS 140 A
Professional
Article number
0 601 297 0..
Rated power input
W
180
No-load speed
min-1
12000
No-load orbital stroke
rate
min-1
24000
mm
1.6
mm
115 x 107
mm
115 x 140
mm
113 x 105
kg
1.4
Orbit diameter
Sanding sheet
dimensions
— Adhesion via Velcro
backing
— Attachment via
clamping
Sanding plate
dimensions
Weight according to
EPTA-Procedure
01/2003
Protection class
/II
The values given are valid for a nominal voltage [U] of 230 V. For
different voltages and models for specific countries, these values
can vary.
Please observe the article number on the type plate of your
machine. The trade names of the individual machines may vary.
Noise/Vibration Information
Measured sound values determined according
to EN 60745.
Typically the A-weighted noise levels of the product are:
Sound pressure level 82 dB(A); Sound power level 93
dB(A). Uncertainty K=3 dB.
Wear hearing protection!
Vibration total values (triax vector sum) determined
according to EN 60745: Vibration emission value ah =6.5
m/s2, Uncertainty K =2.0 m/s2.
Bosch Power Tools
16 | English
The vibration emission level given in this information sheet
has been measured in accordance with a standardised test
given in EN 60745 and may be used to compare one tool
with another.
It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main
applications of the tool. However if the tool is used for
different applications, with different accessories or poorly
maintained, the vibration emission may differ. This may
significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should
also take into account the times when the tool is switched
off or when it is running but not actually doing the job. This
may significantly reduce the exposure level over the total
working period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and
the accessories, keep the hands warm, organisation of work
patterns.
Assembly
uu Before any work on the machine itself, pull the
mains plug.
Replacing the Sanding Sheet
rr Hold the sanding sheet tensely and press the clamping
bracket 3 toward the sanding plate to lock the sanding
sheet.
Sanding sheets without holes, e. g. from rolls or by the
meter, can be punctured with the perforating tool 14. For
this, push the power tool with the sanding sheet mounted
onto the perforating tool (see figure F).
To remove the sanding sheet 4, loosen the clamping bracket
3 and pull out the sanding sheet from the rear holding
fixture. Press the release button 5 and completely remove
the sanding sheet.
Selecting the Sanding Sheet
Depending on the material to be worked and the required
rate of material removal, different sanding sheets are
available:
Grain size
40—240
For the working of all
wooden materials
For coarse-sanding, e. g.
of rough, unplaned
beams and boards
coarse
For face sanding and
planing small
irregularities
medium
When attaching a new sanding sheet, remove any dust or
debris from the sanding plate 2 (e. g. with a brush).
To ensure optimum dust extraction, pay attention that the
punched holes in the sanding sheet match with the holes in
the sanding plate.
For finish and fine
Sanding Sheets with Velcro Backing
sanding of hard woods
The sanding plate 2 is fitted with Velcro backing
for quick and easy fastening of sanding sheets with Velcro
adhesion.
Before attaching the sanding sheet 4, free the Velcro
backing of the sanding plate 2 from any debris by tapping
against it in order to enable optimum adhesion.
Position the sanding sheet 4 flush alongside one edge of the
sanding plate 2, then lay the sanding sheet onto the sanding
plate and press firmly.
To remove the sanding sheet 4, grasp it at one of the tips
and pull it off from the sanding plate 2.
Sanding Sheets without Velcro Backing (see figure A– C)
nn Press the release button 5 and keep it depressed.
oo Guide the sanding sheet 4 to the stop under the opened
front clamping bracket 6 and let go of the release
button 5 again. Pay attention that the sanding sheet is
clamped centrally.
pp Press the sanding sheet clamp 3 inward and pivot it to
the stop.
qq Fold the sanding sheet 4 firmly around the sanding
plate. Guide the other end of the sanding sheet 4
between the rear clamping bracket and the red roller on
the clamping bracket 3.
F 000 622 340 | 06.2011
40, 60
fine
80, 120
180, 240
40—240
For the working of
paint/enamel coats or
primers and fillers
For sanding off paint
coarse
For sanding primer
medium
40, 60
For final sanding of
primers before coating
fine
80, 120
180, 240
Dust/Chip Extraction
uu Dusts from materials such as lead-containing coatings,
some wood types, minerals and metal can be harmful to
one’s health. Touching or breathing-in the dusts can
cause allergic reactions and/or lead to respiratory
infections of the user or bystanders. Certain dusts, such
as oak or beech dust, are considered as carcinogenic,
especially in connection with wood-treatment additives
(chromate, wood preservative). Materials containing
asbestos may only be worked by specialists.
– As far as possible, use a dust extraction system
suitable for the material.
Bosch Power Tools
English | 17
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filterclass respirator.
Observe the relevant regulations in your country for the
materials to be worked.
uu Prevent dust accumulation at the workplace. Dusts
can easily ignite.
Integrated Dust Extraction with Dust Box (see figures D1 – D4)
Attach the dust box 1 onto the extraction outlet 9 until it
latches.
To empty the dust box 1, press the latching levers 10 on the
side of the dust box (). Pull off the dust box toward the
bottom ().
Before opening the dust box 1, it is recommended to loosen
the dust from the filter element by gently striking it against a
firm support (as shown in the figure).
Grasp the dust box 1 by the recessed grip, fold the filter
element 11 upward and empty the dust box. Clean the thin
plates of the filter element 11 with a soft brush.
External Dust Extraction (see figure E)
Slide the extraction adapter 12 onto the outlet piece 9.
Ensure that the latching levers of the extraction adapter
engage. The extraction adapter 12 accepts a vacuum hose
with a diameter of 19 mm.
An overview for connecting to different vacuum cleaners can
be found at the end of these operating instructions.
For removal of the extraction adapter 12, press the latching
levers together at the rear and pull the extraction adapter off.
The vacuum cleaner must be suitable for the material being
worked.
Utilizar um aspirador especial para aspirar pó que seja
extremamente nocivo à saúde, cancerígeno ou seco.
Operation
Starting Operation
uu Observe correct mains voltage! The voltage of the
power source must agree with the voltage specified
on the nameplate of the machine. Power tools
marked with 230 V can also be operated with 220 V.
Switching On and Off
To start the machine, tilt the On/Off switch 7 toward the
right to the “I” position.
To switch off the machine, tilt the On/Off switch 7 toward
the left to the “0” position.
increase of the sanding capacity, but to increased wear of
the machine and the sanding sheet.
A sanding sheet that has been used for metal should not be
used for other materials.
Use only original Bosch sanding accessories.
Maintenance and cleaning
uu Before any work on the machine itself, pull the mains
plug.
uu For safe and proper working, always keep the
machine and ventilation slots clean.
If the machine should fail despite the care taken in manufacturing and testing procedures, repair should be carried out
by an after-sales service centre for Bosch power tools.
In all correspondence and spare parts order, please always
include the 10-digit article number given on the type plate
of the machine.
After-sales Service and Customer Assistance
Our after-sales service responds to your questions
concerning maintenance and repair of your product as well
as spare parts. Exploded views and information on spare
parts can also be found under:
www.bosch-pt.com
Our customer service representatives can answer your
questions concerning possible applications and adjustment
of products and accessories.
Guarantee
We guarantee BOSCH appliances in accordance with
statutory/country-specific regulations (proof of purchase
by invoice or delivery note). Damage attributable to normal
wear and tear, overload or improper handling will be
excluded from the guarantee.
In case of complaint please send the machine,
undismantled, to your dealer or the BOSCH Service Center
for Electric Power Tools.
Warning! Freight and insurance costs are charged to the
client, even for warranty claims.
Enviromental Protection
The machine, accessories and packaging
should be sorted for environmentalfriendly recycling.
Working Advice
uu Wait until the machine has come to a standstill
before placing it down.
The removal capacity during sanding is mainly determined
by the selection of the sanding sheet.
Only flawless sanding sheets achieve good sanding capacity
and extend the service life of the machine.
Pay attention to apply uniform sanding pressure; this
increases the working life of the sanding sheets.
Intensifiying the sanding pressure does not lead to an
F 000 622 340 | 06.2011
If you discard your machine, accessories, do not put off
in the trash, please give it to a technical service Bosch. It
will provide a better destination according the politics of
preservation of the environment, recycling parts according
the local laws.
Subject to change without notice.
Bosch Power Tools