With Universal Dock for iPod®
Model No. PFTL97908.0
Serial No.
Write the serial number in the space
above for reference.
USER'S MANUAL
Serial Number
Decal
QUESTIONS?
As a manufacturer, we are committed to providing complete customer satisfaction. If you have
questions, or if parts are missing,
PLEASE DO NOT CONTACT
THE STORE; please contact
Customer Care.
IMPORTANT: You must note the
product model number and
serial number (see the drawing
above) before contacting us:
1-888-533-1333
CALL TOLL-FREE:
Mon.–Fri. 6 a.m.–6 p.m. MST
Sat. 8 a.m.–4 p.m. MST
ON THE WEB:
www.proformservice.com
CAUTION
Read all precautions and instructions in this manual before using
this equipment. Save this manual
for future reference.
Visit our website at
www.proform.com
new products, prizes,
fitness tips, and much more!
TABLE OF CONTENTS
WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
OPERATION AND ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
HOW TO FOLD AND MOVE THE TREADMILL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
EXERCISE GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
PART LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
EXPLODED DRAWING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
WARNING DECAL PLACEMENT
This drawing shows the locations of the warning decals. If a decal is missing or illegible,
call the telephone number on the front cover
of this manual and request a free replacement decal. Apply the decal in the location
shown. Note: The decals may not be shown at
actual size.
PROFORM is a registered trademark of ICON IP, Inc.
iPod® is a trademark of Apple Computer, Inc., registered in the U.S. and other countries.
2
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of serious injury, read all important precautions and instructions in this manual and all warnings on your treadmill before using your treadmill. ICON assumes no responsibility for personal injury or property damage sustained by or through the use of
this product.
1. Before beginning any exercise program, consult your physician. This is especially important for persons over age 35 or persons with
pre-existing health problems.
of carrying 15 or more amps. No other appliance should be on the same circuit. Do not
use an extension cord.
12. Use only a single-outlet surge suppressor that
meets all of the specifications described on
page 12. To purchase a surge suppressor, see
your local PROFORM dealer or call the telephone number on the front cover of this manual and order part number 146148, or see your
local electronics store.
2. It is the responsibility of the owner to ensure
that all users of this treadmill are adequately
informed of all warnings and precautions.
3. Use the treadmill only as described.
4. Place the treadmill on a level surface, with at
least 8 ft. (2.4 m) of clearance behind it and 2
ft. (0.6 m) on each side. Do not place the
treadmill on any surface that blocks air openings. To protect the floor or carpet from damage, place a mat under the treadmill.
13. Failure to use a properly functioning surge
suppressor could result in damage to the control system of the treadmill. If the control system is damaged, the walking belt may slow,
accelerate, or stop unexpectedly, which may
result in a fall and serious injury.
5. Keep the treadmill indoors, away from moisture and dust. Do not put the treadmill in a
garage or covered patio, or near water.
14. Keep the power cord and the surge suppressor away from heated surfaces.
6. Do not operate the treadmill where aerosol
products are used or where oxygen is being
administered.
15. Never move the walking belt while the power
is turned off. Do not operate the treadmill if
the power cord or plug is damaged, or if the
treadmill is not working properly. (See TROUBLESHOOTING on page 22 if the treadmill is
not working properly.)
7. Keep children under age 12 and pets away
from the treadmill at all times.
8. The treadmill should be used only by persons weighing 325 lbs. (147 kg) or less.
16. Read, understand, and test the emergency
stop procedure before using the treadmill (see
HOW TO TURN ON THE POWER on page 14).
9. Never allow more than one person on the
treadmill at a time.
17. Never start the treadmill while you are standing on the walking belt. Always hold the
handrails while using the treadmill.
10. Wear appropriate exercise clothes when
using the treadmill. Do not wear loose
clothes that could become caught in the
treadmill. Athletic support clothes are recommended for both men and women. Always
wear athletic shoes. Never use the treadmill
with bare feet, wearing only stockings, or in
sandals.
18. The treadmill is capable of high speeds.
Adjust the speed in small increments to
avoid sudden jumps in speed.
19. The pulse sensor is not a medical device.
Various factors, including the user's movement, may affect the accuracy of heart rate
readings. The pulse sensor is intended only
as an exercise aid in determining heart rate
trends in general.
11. When connecting the power cord (see page
12), plug the power cord into a surge suppressor (not included) and plug the surge
suppressor into a grounded circuit capable
3
24. Inspect and properly tighten all parts of the
treadmill regularly.
20. Never leave the treadmill unattended while it
is running. Always remove the key, unplug
the power cord, and switch the reset/off circuit breaker to the off position when the
treadmill is not in use. (See the drawing on
page 5 for the location of the circuit breaker.)
25.
21. Do not attempt to raise, lower, or move the
treadmill until it is properly assembled. (See
ASSEMBLY on page 6, and HOW TO FOLD
AND MOVE THE TREADMILL on page 20.)
You must be able to safely lift 45 lbs. (20 kg)
to raise, lower, or move the treadmill.
DANGER:
Always unplug the power
cord immediately after use, before cleaning the
treadmill, and before performing the maintenance and adjustment procedures described in
this manual. Never remove the motor hood unless instructed to do so by an authorized service representative. Servicing other than the
procedures in this manual should be performed
by an authorized service representative only.
26. This treadmill is intended for in-home use
only. Do not use this treadmill in a commercial, rental, or institutional setting.
22. When folding or moving the treadmill, make
sure that the storage latch is holding the
frame securely in the storage position.
23. Never insert any object into any opening on
the treadmill.
SAVE THESE INSTRUCTIONS
4
BEFORE YOU BEGIN
Thank you for selecting the revolutionary PROFORM®
780 CS treadmill with Universal Dock for iPod. The
780 CS treadmill with Universal Dock for iPod offers a
selection of features designed to make your workouts
at home more enjoyable and effective. And when
youʼre not exercising, the unique treadmill can be
folded up, requiring less than half the floor space of
other treadmills.
ual. To help us assist you, note the product model
number and serial number before contacting us. The
model number and the location of the serial number
decal are shown on the front cover of this manual.
To avoid a registration fee for any service needed
under warranty, you must register the treadmill at
www.proformservice.com/registration.
For your benefit, read this manual carefully before
using the treadmill. If you have questions after reading this manual, please see the front cover of this man-
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
Speaker
Accessory Tray
Console
Pulse Sensor
Handrail
Key/Clip
Upright
Reset/Off
Circuit Breaker
Power Cord
Walking Belt
Foot Rail
Platform Cushion
Rear Roller
Adjustment Bolts
5
ASSEMBLY
To hire an authorized service technician to assemble the treadmill, call 1-800-445-2480.
Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials. Do not
dispose of the packing materials until assembly is completed. Note: The underside of the treadmill walking
belt is coated with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to
the top of the walking belt or the shipping carton. This is a normal condition and does not affect treadmill performance. If there is lubricant on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild,
non-abrasive cleaner.
Assembly requires the included hex keys and your own Phillips screwdriver
adjustable wrench
, rubber mallet
, and needlenose pliers
.
,
Use the drawings below to identify the assembly hardware. The number in parentheses below each drawing is
the key number of the part, from the PART LIST near the end of this manual. The number after the parentheses
is the quantity needed for assembly. Note: If a part is not in the parts bag, check to see if it is preattached to
one of the parts to be assembled. To avoid damaging plastic parts, do not use power tools for assembly.
Extra hardware may be included.
Base Pad Spacer
(13)–2
#8 x 3/4" Screw (1)–4
1/4" x 1 1/4" Bolt (5)–2
3/8" Nut (8)–3
3/8" Star
Washer (9)–4
#8 x 1" Tek Screw (2)–4
5/16" x 1 1/4" Bolt (7)–6
3/8" x 5" Bolt (6)–4
6
5/16" Star
Washer (10)–6
1/4" Star
Washer (33)–2
Bolt Spacer (90)–4
3/8" x 2" Bolt (4)–3
1. Make sure that the power cord is unplugged.
1
With the help of a second person, carefully tip
the treadmill onto its left side. Partially fold the
Frame (56) so that the treadmill is more stable;
do not fully fold the Frame yet.
B
38
Remove and discard the two indicated bolts (A)
and the shipping bracket (B).
Cut the ties securing the Upright Wire (38) to the
Base (83). Locate a tie in the indicated hole in
the Base, and use the tie to pull the Upright Wire
out of the hole.
A
Hole
81
2
83
Attach a Base Pad (81) to the Base (83) in the
location shown with a Base Pad Spacer (13) and
a #8 x 1" Tek Screw (2). Then, attach another
Base Pad (81) with only a #8 x 1" Tek Screw (2).
56
2. Remove the 3/8" Nut (8), the 3/8" x 2" Bolt (4),
and the shipping bracket (C) from the Base (83).
Attach a Wheel (84) with the Bolt and the Nut
that you just removed. Do not overtighten the
Nut; the Wheel must turn freely. Discard the
shipping bracket.
13
81
2
2
83
4
C
3. Identify the Right Upright (78) and the Right
Upright Spacer (79), which are marked with
stickers. Insert the Upright Wire (38) through the
Right Upright Spacer as shown. Set the Right
Upright Spacer on the Base (83). Be careful
not to pinch the Upright Wire.
3
84
8
78
38
Long Tie
Have a second person hold the Right Upright
(78) near the Base (83). See the inset drawing.
Tie the long tie in the Right Upright securely
around the end of the Upright Wire (38). Then,
pull the other end of the long tie until the Upright
Wire is routed completely through the Right
Upright.
38
79
83
38
7
78
Long
Tie
4. With the help of a second person, hold a Bolt
Spacer (90) inside the lower end of the Right
Upright (78). Insert a 3/8" x 5" Bolt (6) with a
3/8" Star Washer (9) into the Right Upright and
the Bolt Spacer. Repeat this step with a second Bolt Spacer (90), 3/8" x 5" Bolt (6), and
3/8" Star Washer (9). Set the Right Upright into
the Right Upright Spacer (79).
4
6
78
79
9
Partially tighten the 3/8" x 5" Bolts (6); do not
fully tighten the Bolts yet.
77
38
Press a Base Endcap (77) into the Base (83).
83
5. With the help of a second person, carefully tip
the treadmill onto its right side. Partially fold the
Frame (56) so that the treadmill is more stable;
do not fully fold the Frame yet.
5
A
Remove and discard the two indicated bolts (A)
and the shipping bracket (B).
Attach a Base Pad (81) to the Base (83) in the
location shown with a #8 x 1" Tek Screw (2) and
a Base Pad Spacer (13). Then, attach another
Base Pad (81) with only a #8 x 1" Tek Screw (2).
2
B
83
81
Remove the 3/8" Nut (8), the 3/8" x 2" Bolt (4),
and the shipping bracket (C) from the Base (83).
Attach a Wheel (84) with the Bolt and the Nut
that you just removed. Do not overtighten the
Nut; the Wheel must turn freely. Discard the
shipping bracket.
13
2 81
6. Set the Left Upright Spacer (76) on the Base
(83). With the help of a second person, hold a
Bolt Spacer (90) inside the lower end of the Left
Upright (74). Insert a 3/8" x 5" Bolt (6) with a
3/8" Star Washer (9) into the Left Upright and
the Bolt Spacer. Repeat this step with a second Bolt Spacer (90), 3/8" x 5" Bolt (6), and
3/8" Star Washer (9). Set the Left Upright into
the Left Upright Spacer.
6
6
77
Partially tighten the 3/8" x 5" Bolts (6); do not
fully tighten the Bolts yet.
90
Press a Base Endcap (77) into the Base (83).
With the help of a second person, tip the treadmill so that the Base (83) is flat on the floor.
8
9
76
56
4
84
C
8
74
83
90
7. Set the console assembly face down on a soft
surface to avoid scratching the console assembly. Hold the Right Handrail (95) near the console assembly. Next, insert the console wire into
the large hole in the Right Handrail and out of
the top as shown. If necessary, use needlenose
pliers to pull the console wire out.
7
Console
Wire
95
Attach the Right Handrail (95) and the Left
Handrail (not shown) with four #8 x 3/4" Screws
(1) (only two are shown). Make sure that no
wires are pinched. Start all four Screws before tightening any of them; do not overtighten the Screws.
1
Console
Assembly
8. Tighten a 1/4" x 1 1/4" Bolt (5) with a 1/4" Star
Washer (33) into the bracket and the Handrail
Crossbar (94) on each side of the console assembly (only one side is shown).
8
Wire
Tie
Console
Wire
5
33
Remove the wire tie from the console wire.
Console
Assembly
9. Have a second person hold the console assembly near the Right Upright (78) and the Left
Upright (not shown). Connect the Upright Wire
(38) to the console wire. See the inset drawing. The connectors should slide together
easily and snap into place. If they do not, turn
one connector and try again. IF THE CONNECTORS ARE NOT CONNECTED PROPERLY,
THE CONSOLE MAY BE DAMAGED WHEN
THE POWER IS TURNED ON. Then, remove
the long tie from the Upright Wire.
9
78
9
94
Console
Assembly
Console
Wire
Set the console assembly on the Right Upright
(78) and the Left Upright (not shown). Be careful not to pinch the wires.
Bracket
38
Long
Tie
Console
Wire
38
10. Attach the console assembly with six 5/16" x 1
1/4" Bolts (7) and six 5/16" Star Washers (10)
(only three are shown).
10
Console
Assembly
See steps 4 and 6. Tighten the 3/8" x 5" Bolts
(6).
7
11. Identify the Storage Latch (53). Remove the tie
from the end of the tube. Make sure that the
sleeve has been slid over the indicated hole and
that the Latch Knob (54) is locked into the hole.
Pull on the sleeve to make sure that it is
locked into place.
10
10
10
7
11
54
Tube
12. Raise the Frame (56) to the position shown.
Have a second person hold the Frame until
this step is completed.
Sleeve
12
Orient the Storage Latch (53) so that the large
barrel and the Latch Knob (54) are in the positions shown.
4
53
54
Attach the upper end of the Storage Latch (53)
to the bracket on the Frame (56) with a 3/8" x 2"
Bolt (4) and a 3/8" Nut (8). Note: It may be necessary to move the Frame back and forth to
align the Storage Latch with the bracket.
53
56
8
Attach the Latch Bracket (14) and the Storage
Latch (53) to the Base (83) with two 3/8" x 2"
Bolts (4) and two 3/8" Nuts (8).
Hole
Large
Barrel
14
8
Lower the Frame (56) (see HOW TO LOWER
THE TREADMILL FOR USE on page 21).
10
83
4
13. Press the Left Accessory Tray (99) and the
Right Accessory Tray (106) into the console assembly.
13
99
Console
Assembly
106
14. Make sure that all parts are properly tightened before you use the treadmill. If there are sheets of clear
plastic on the treadmill decals, remove the plastic. To protect the floor or carpet, place a mat under the treadmill. Note: Extra hardware may be included. Keep the included hex keys in a secure place; a hex key is used
to adjust the walking belt (see pages 23 and 24).
11
OPERATION AND ADJUSTMENT
THE PRE-LUBRICATED WALKING BELT
tric shock. This product is equipped with a cord having
an equipment-grounding conductor and a grounding
plug. Plug the power cord into a surge suppressor,
and plug the surge suppressor into an appropriate
outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
IMPORTANT: The treadmill is not compatible with
GFCI-equipped outlets.
Your treadmill features a walking belt coated with highperformance lubricant. IMPORTANT: Never apply silicone spray or other substances to the walking
belt or the walking platform. Such substances will
deteriorate the walking belt and cause excessive
wear.
HOW TO PLUG IN THE POWER CORD
This product is for use on a nominal 120-volt circuit,
and has a grounding plug that looks like the plug illustrated in drawing 1 below. A temporary adapter that
looks like the adapter illustrated in drawing 2 may be
used to connect the surge suppressor to a 2-pole
receptacle as shown in drawing 2 if a properly
grounded outlet is not available.
DANGER:
Improper connection
of the equipment-grounding conductor can
result in an increased risk of electric shock.
Check with a qualified electrician or serviceman if you are in doubt as to whether the
product is properly grounded. Do not modify
the plug provided with the product—if it will
not fit the outlet, have a proper outlet
installed by a qualified electrician.
1
Surge Suppressor
Grounding Pin
Your treadmill, like any other type of sophisticated
electronic equipment, can be seriously damaged by
sudden voltage changes in your homeʼs power.
Voltage surges, spikes, and noise interference can
result from weather conditions or from other appliances
being turned on or off. To decrease the possibility of
your treadmill being damaged, always use a surge
suppressor with your treadmill (see drawing 1 at
the right). To purchase a surge suppressor, see
your local PROFORM dealer or call the telephone
number on the front cover of this manual and order
part number 146148, or see your local electronics
store.
Grounding Pin
2
Use only a single-outlet surge suppressor that is
UL 1449 listed as a transient voltage surge suppressor (TVSS). The surge suppressor must have a
UL suppressed voltage rating of 400 volts or less
and a minimum surge dissipation of 450 joules.
The surge suppressor must be electrically rated for
120 volts AC and 15 amps. There must be a monitoring light on the surge suppressor to indicate
whether it is functioning properly. Failure to use a
properly functioning surge suppressor could result
in damage to the control system of the treadmill. If
the control system is damaged, the walking belt
may slow, accelerate, or stop unexpectedly, which
may result in a fall and serious injury.
This product must be grounded. If it should malfunction or break down, grounding provides a path of least
resistance for electric current to reduce the risk of elec-
Grounded Outlet Box
Grounded Outlet
Grounding Plug
Grounded Outlet Box
Adapter
Surge Suppressor
Lug
Metal Screw
The temporary adapter should be used only until a
properly grounded outlet (drawing 1) can be installed
by a qualified electrician.
12
The green-colored rigid ear, lug, or the like extending
from the adapter must be connected to a permanent
ground such as a properly grounded outlet box cover.
Whenever the adapter is used it must be held in place
by a metal screw. Some 2-pole receptacle outlet box
covers are not grounded. Contact a qualified electrician to determine if the outlet box cover is
grounded before using an adapter.
CONSOLE DIAGRAM
Integrated Universal Dock for iPod
Navigation Buttons
FEATURES OF THE CONSOLE
The treadmill console offers an impressive array of
features designed to help you get the most from your
workouts. When the manual mode of the console is selected, the speed and incline of the treadmill can be
changed with the touch of a button. As you exercise,
the console will display continuous exercise feedback.
You can even measure your heart rate using the builtin handgrip pulse sensor.
In addition, the console features fifteen preset workouts–five weight loss, five performance, and five aerobic workouts. Each workout automatically controls the
speed and incline of the treadmill as it guides you
through an effective workout.
The console also features the new iFit Interactive
Workout system. The iFit system enables the console
to accept iFit Interactive Workout Cards containing
workouts designed to help you achieve specific fitness
goals. For example, lose unwanted pounds with the 8-
week Weight Loss workout, or train for a long-distance
run with the Marathon workout. iFit workouts automatically control the treadmill while the voice of a personal
trainer coaches you and through every step of your
workout. iFit cards are available separately. To purchase iFit cards at any time, go to www.iFit.com or
call the telephone number on the front cover of
this manual. iFit cards are also available at select
stores.
You can even listen to your favorite workout music or
audio books with the consoleʼs premium stereo sound
system while you get in shape. This product has been
designed specifically to work with iPod and has been
certified by the developer to meet Apple performance
standards.
To turn on the power, see page 14. To use the manual mode of the console, see page 14. To use a preset workout, see page 17. To use an iFit card, see
page 18. To use the stereo sound system, see page
19. To use the information mode, see page 19.
13
HOW TO TURN ON THE POWER
IMPORTANT: If the treadmill has been exposed to
cold temperatures, allow it to warm to room temperature before turning on the power. If you do not
do this, the console displays or other electrical
components may become damaged.
Plug in the power cord
(see page 12). Next, locate the reset/off circuit
breaker on the treadmill
frame near the power
cord. Switch the circuit
breaker to the reset position.
HOW TO USE THE MANUAL MODE
1. Insert the key into the console.
See HOW TO TURN ON THE POWER at the left.
2. Select the manual mode.
When the key is
inserted, the
manual mode
will be selected.
If a workout has
been selected,
reselect the
manual mode by removing the key and then reinserting it.
Reset
Position
IMPORTANT: The console features a display demo
mode, designed to be used if the treadmill is displayed in a store. If the displays light as soon as
you plug in the power cord and switch the reset/off
circuit breaker to the reset position, the demo
mode is turned on. To turn off the demo mode,
hold down the Stop button for a few seconds. If the
displays remain lit, see THE INFORMATION MODE
on page 19 to turn off the demo mode.
3. Start the walking belt.
To start the walking belt, press the Start button, the
Speed increase button, or one of the speed buttons numbered 1 through 10.
If you press the Start button or the Speed increase
button, the walking belt will begin to move at 1 mph.
As you exercise, change the speed of the walking
belt as desired by pressing the Speed increase
and decrease buttons. Each time you press the
Speed increase or decrease button, the speed setting will change by 0.1 mph; if you hold down a button, the speed setting will change in increments of
0.5 mph. Note: After you press the buttons, it may
take a moment for the walking belt to reach the selected speed setting.
Next, stand on the foot
rails of the treadmill. Find
Key
the clip attached to the key
(see the drawing at the
Clip
right) and slide the clip
onto the waistband of your
clothes. Then, insert the
key into the console. After a moment, the displays will
light. IMPORTANT: In an emergency situation, the
key can be pulled from the console, causing the
walking belt to slow to a stop. Test the clip by
carefully taking a few steps backward; if the key is
not pulled from the console, adjust the position of
the clip.
If you press one of the speed buttons numbered 1
through 10, the walking belt will gradually change
speed until it reaches the selected speed setting.
To stop the walking belt, press the Stop button. To
restart the walking belt, press the Start button, the
Speed increase button, or one of the numbered
speed buttons.
IMPORTANT: If there are sheets of clear plastic on
the console, remove the plastic. To prevent damage
to the walking platform, wear clean athletic shoes
while using the treadmill. The first time you use the
treadmill, observe the alignment of the walking
belt, and center the walking belt if necessary (see
page 24).
Note: The console can display speed and distance in
either miles or kilometers. To find out which unit of
measurement is selected or to change the unit of measurement, see THE INFORMATION MODE on page
19. Note: For simplicity, all instructions in this section
refer to miles.
14
4. Change the incline of the treadmill as desired.
• The number of laps you have completed.
To change the
incline of the
treadmill, press
the Incline increase and decrease buttons.
Each time you
press the Incline increase or decrease button, the
incline will change by 0.5%. To change the incline
quickly, press one of the incline buttons numbered
0 through 12. Note: After you press the Incline buttons, it may take a moment for the treadmill to
reach the selected incline setting.
• The incline setting of the treadmill. Note: The incline setting will be displayed only when the incline setting changes.
• Your heart rate. Note: Your heart rate can be displayed only while you use the handgrip pulse sensor.
• The display can also show an animation of a
road.
Regardless of which display mode you select, the
speed or incline setting will appear in the display for
a few seconds each time you change the setting.
5. Select a display mode and monitor your
progress with the display.
You can change the volume level by pressing the
Volume increase and decrease buttons.
When the manual mode is selected, the console offers three display modes. The display mode that
you select will determine which workout information
is shown. Press the Display button repeatedly to
select the desired display mode.
As you exercise, the workout intensity level bar will
indicate the approximate intensity level of your exercise. For example, if eight of the indicators in the
bar are lit, the bar shows that your intensity level is
ideal for aerobic exercise.
As you walk or run on the treadmill, the display can
show the following workout information:
Workout Intensity Level Bar
• The speed of the walking belt.
• Your walking or running pace, in minutes per mile
or minutes per kilometer.
To reset the console, press the Stop button, remove the key, and then reinsert the key.
• The approximate number of calories you have
burned.
• The elapsed time.
• The distance that you have walked or run.
15
6. Measure your heart rate if desired.
Before using the
handgrip pulse
sensor, remove
the clear plastic
film from the
metal contacts.
In addition,
make sure that
your hands are clean.
7. Turn on the fan if desired.
The fan features high, low, and auto speed settings. Press the Fan button repeatedly to select a
fan speed or to turn off the fan. When the auto
mode is selected, the speed of the fan will automatically increase and decrease as the speed of
the walking belt increases and decreases. Note: If
the fan is on when the walking belt is stopped, the
fan will turn off automatically after a few minutes.
Contacts
8. When you are finished exercising, remove the
key from the console.
To measure your heart rate, stand on the foot
rails and hold the metal contacts—avoid moving
your hands. When your pulse is detected, your
heart rate will be shown. For the most accurate
heart rate reading, continue to hold the contacts
for about 15 seconds.
Step onto the foot rails, press the Stop button, and
adjust the incline of the treadmill to the lowest
setting. The incline must be at the lowest setting
or you may damage the treadmill when you fold
it to the storage position. Next, remove the key
from the console and put it in a secure place.
When you are finished using the treadmill, switch
the reset/off circuit breaker to the “off” position and
unplug the power cord. IMPORTANT: If you do
not do this, the treadmillʼs electrical components may wear prematurely.
16
HOW TO USE A PRESET WORKOUT
A profile of the
speed settings of
the workout will
appear in the display. A small
arrow below the
profile will indicate your progress.
1. Insert the key into the console.
See HOW TO TURN ON THE POWER on page
14.
2. Select one of the preset workouts.
To select a
weight loss
workout or a
performance
workout, press
the Weight Loss
Workouts button or the Performance Workouts button. Profiles
of the speed settings of the workouts will appear in
the display. To select an aerobic workout, press
the Weight Loss Workouts button and then press
the down Navigation button until the aerobic profiles appear in the display. Use the Navigation buttons to highlight the desired profile. The maximum
speed setting and maximum incline setting of the
workout will be shown. Press Enter to select the
workout.
At the end of the first one-minute segment of the
workout, a series of tones will sound. If a different
speed setting and/or incline setting is programmed
for the second segment, the speed and/or incline
setting will flash in the display for a moment to alert
you. The treadmill will then automatically adjust to
the speed and incline settings for the second segment.
The workout will continue in this way until the small
arrow reaches the right end of the profile. The
walking belt will then slow to a stop.
If the speed or incline setting is too high or too low
at any time during the workout, you can override
the setting by pressing the Speed or Incline buttons; however, when the next segment begins,
the treadmill will automatically adjust to the
speed and incline settings for the next
segment.
As each preset
workout is selected, the maximum speed
setting of the
workout and the
maximum incline setting of the workout will flash in the displays
for a few seconds. The workout time and a profile
of the speed settings of the workout will appear in
the display.
To stop the workout at any time, press the Stop
button. To restart the workout, press the Start button. The walking belt will begin to move at 1 mph.
When the next segment of the workout begins, the
treadmill will automatically adjust to the speed and
incline settings for the next segment.
4. Select a display mode and monitor your
progress with the display.
3. Press the Start button or the Speed increase
button to start the workout.
See step 5 on page 15.
5. Measure your heart rate if desired.
A moment after you press the button, the treadmill
will automatically adjust to the first speed and incline settings for the workout. Hold the handrails
and begin walking.
See step 6 on page 16.
6. Turn on the fan if desired.
Each workout is divided into one-minute segments.
One speed setting and one incline setting are programmed for each segment. Note: The same and/or
incline setting may be programmed for consecutive
segments.
See step 7 on page 16.
7. When you are finished exercising, remove the
key from the console.
See step 8 on page 16.
17
HOW TO USE AN IFIT CARD
cline settings of the workout. Hold the handrails
and begin walking.
1. Insert the key into the console.
During the workout, a personal trainer will guide you
through the workout. You can select an audio setting
for your personal trainer (see THE INFORMATION
MODE on page 19).
See HOW TO TURN ON THE POWER on page
14.
2. Insert an iFit card and select a workout.
If the speed or incline setting for the current segment is too high or too low, you can manually override the setting by pressing the Speed or Incline
buttons; however, when the next segment begins, the treadmill will automatically adjust to
the speed and incline settings for the next segment.
To use an iFit workout, insert an iFit card into the
iFit slot; make sure that the iFit card is oriented so
the metal contacts are face-down and are inserted
into the iFit slot.
iFit Card
iFit Slot
Next, select an iFit workout by pressing the iFit up
and down buttons next to the iFit slot. When an iFit
workout is selected, the display will show the name
of the workout, the maximum incline setting and
the maximum speed setting of the workout, and the
workout time. In addition, a profile of the speed settings of the workout will appear in the display.
Each iFit workout is divided into several oneminute segments. One speed setting and one incline setting are programmed for each segment.
Note: The same speed and/or incline setting may
be programmed for consecutive segments.
To stop the workout at any time, press the Stop
button. To restart the workout, press the Start button or the Speed increase button. The walking belt
will begin to move at 1 mph. When the next segment of the workout begins, the treadmill will automatically adjust to the speed and incline settings for
the next segment.
4. Select a display mode and monitor your
progress with the display.
See step 5 on page 15.
5. Turn on the fan if desired.
See step 7 on page 16.
6. When you are finished exercising, remove the
key from the console.
See step 8 on page 16.
CAUTION: Always remove iFit cards from the
iFit slot when you are not using them.
3. Press the Start button or the Speed increase
button to start the workout.
A moment after the button is pressed, the treadmill
will automatically adjust to the first speed and in-
18
HOW TO USE THE STEREO SOUND SYSTEM
This product has been designed specifically to work
with iPod and has been certified by the developer to
meet Apple performance standards. To play music or
audio books through the consoleʼs stereo speakers,
you must connect your iPod, MP3 player, CD player,
or other personal audio player to the console through
the audio jack or through the Integrated Universal
Dock for iPod.
To use the audio wire, locate the audio wire and plug it
into the audio jack near the speakers. Then plug the
audio wire into a jack on your MP3 player, CD player,
or other personal audio player. Make sure that the
audio wire is fully plugged in.
To use the Integrated Universal Dock for iPod, you
need an iFit Universal iPod Connector (not included).
Plug one end into the Integrated Universal Dock for
iPod near the speakers and the other end into your
iPod. Make sure that the iFit Universal iPod
Connector is fully plugged in. To purchase an iFit
Universal iPod Connector, please call the telephone number on the front cover of this manual.
Next, press the Play button on your iPod, MP3 player,
CD player, or other personal audio player. Adjust the
volume on your personal audio player or press the
Volume increase and decrease buttons on the console.
If you are using a personal CD player and the CD
skips, set the CD player on the floor or another flat surface and not on the console.
THE INFORMATION MODE
The console features a userʼs mode that keeps track of
the total number of miles that the walking belt has
moved and the total number of hours that the treadmill
has been operated. The userʼs mode also allows you
to select miles or kilometers as the unit of measurement and to turn on and turn off the demo mode. You
can also choose an audio setting for your iFit workouts.
To select the information mode, hold down the Stop
button while inserting the key into the console and then
release the Stop button. When the information mode is
selected, the following information will be shown:
You can select an audio setting if desired. When you
use an iFit card, a personal trainer will guide you
through your workouts. If you select the ON setting,
the personal trainer will give you detailed instructions.
If you select the OFF setting, your personal trainer will
simply guide you through your iFit workouts. To
change the audio setting, press the Incline decrease
button.
The display will show the total number of hours the
treadmill has been used. The display will also show the
total number of miles (or kilometers) that the walking
belt has moved.
The word ENGLISH for miles or METRIC for kilometers
will appear in the display. Press the Speed increase
button to change the unit of measurement if desired.
The console features a display demo mode, designed
to be used if the treadmill is displayed in a store. While
the demo mode is turned on, the console will function
normally when you plug in the power cord, switch the
reset/off circuit breaker to the reset position, and insert
the key into the console. However, when you remove
the key, the displays will remain lit, although the buttons will not function. If the demo mode is turned on,
the word ON will appear in the display while the information mode is selected. To turn on or off the demo
mode, press the Speed decrease button.
To exit the information mode, remove the key from the
console.
HOW TO ADJUST THE CUSHIONING SYSTEM
Remove the key from the console and unplug the
power cord. The treadmill features a cushioning system that reduces the impact as you walk or run on the
treadmill. To increase the firmness of the walking platform, step off the treadmill and slide the platform cushions toward the front of the treadmill. To decrease the
firmness, step off the treadmill and slide the platform
cushions toward the back of the treadmill. Note: Make
sure that both cushions are set at the same firmness level. The faster you run on the treadmill, or
the more you weigh, the firmer the walking platform should be.
Platform
Cushion
Decrease
19
Increase
Platform
Cushion
Walking Platform
HOW TO FOLD AND MOVE THE TREADMILL
HOW TO FOLD THE TREADMILL FOR STORAGE
Before folding the treadmill, adjust the incline to the
lowest position. If you do not do this, you may damage the
treadmill when you fold it. Remove the key and unplug the
power cord. CAUTION: You must be able to safely lift 45
lbs. (20 kg) to raise, lower, or move the treadmill.
1. Hold the metal frame firmly in the location shown by
the arrow at the right. CAUTION: To decrease the possibility of injury, do not lift the frame by the plastic
foot rails. Make sure to bend your legs and keep your
back straight as you raise the frame. Raise the frame
about halfway to the vertical position.
2. Raise the frame until the latch knob locks into the storage
position. Make sure that the latch knob is locked in
the storage position.
To protect the floor or carpet from damage, place a
mat under the treadmill. Keep the treadmill out of direct sunlight. Do not leave the treadmill in the storage position in temperatures above 85° F (30° C).
Frame
Latch Knob
HOW TO MOVE THE TREADMILL
Before moving the treadmill, convert the treadmill to the storage position as described above. Make sure that the latch
knob is locked in the storage position.
1. Hold a handrail and the frame and place one foot against
one of the wheels.
2. Tilt the treadmill back until it rolls freely on the wheels.
Carefully move the treadmill to the desired location. Never
move the treadmill without tipping it back. To reduce
the risk of injury, use extreme caution while moving
the treadmill. Do not attempt to move the treadmill
over an uneven surface.
3. Place one foot against a wheel, and carefully lower the
treadmill until it is resting in the storage position.
20
Frame
Handrail
Wheel
Base
HOW TO LOWER THE TREADMILL FOR USE
1. Hold the upper end of the treadmill with your right hand.
Pull the latch knob to the left and hold it. It may be necessary to push the frame forward as you pull the knob to
the left. Pivot the frame downward and release the latch
knob.
Frame
Latch Knob
2. Hold the metal frame firmly with both hands and lower
it to the floor. CAUTION: Do not grip only the plastic
foot rails or drop the frame to the floor. Bend your
legs and keep your back straight.
21
TROUBLESHOOTING
Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and
follow the steps listed. If further assistance is needed, please see the front cover of this manual.
PROBLEM: The power does not turn on
SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor
is plugged into a properly grounded outlet (see page 12). Use only a single-outlet surge suppressor that meets all of the specifications described on page 12. IMPORTANT: The treadmill is not
compatible with GFCI-equipped outlets.
b. After the power cord has been plugged in, make sure that the key is inserted into the console.
c. Check the reset/off circuit breaker located on the
treadmill frame near the power cord. If the switch
protrudes as shown, the circuit breaker has
tripped. To reset the circuit breaker, wait for five
minutes and then press the switch back in.
c
Tripped
Position
PROBLEM: The power turns off during use
Reset
Position
SOLUTION: a. Check the reset/off circuit breaker (see the drawing above). If the circuit breaker has tripped, wait
for five minutes and then press the switch back in.
b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for
five minutes, and then plug it back in.
c. Remove the key from the console. Reinsert the key into the console.
d. If the treadmill still will not run, please see the front cover of this manual.
PROBLEM: The console displays remain lit when you remove the key from the console
SOLUTION: a. The console features a display demo mode, designed to be used if the treadmill is displayed in a
store. If the displays remain lit when you remove the key, the demo mode is turned on. To turn off
the demo mode, hold down the Stop button for a few seconds. If the displays are still lit, see THE
INFORMATION MODE on page 19 to turn off the demo mode.
PROBLEM: The displays of the console do not function properly
SOLUTION: a. Remove the key from the console and UNPLUG
THE POWER CORD. With the help of a second
person, carefully tip down the Uprights (74, 78).
There may be two #8 x 2" Screws (105) in the bottom of the Belly Pan (73). If there are, remove
them. Note: A Phillips screwdriver with a shaft at
least 5 in. (13 cm) long is required. Raise the
Uprights to a vertical position.
a
74
78
73
105
22
105
Remove the three #8 x 3/4" Screws (1) and carefully pivot the Hood (61) off.
1
61
Locate the Reed Switch (71) and the Magnet (50)
on the left side of the Pulley (51). Turn the Pulley
until the Magnet is aligned with the Reed Switch.
Make sure that the gap between the Magnet and
the Reed Switch is about 1/8 in. (3 mm). If necessary, loosen the 3/4" Reed Switch Screw (15),
move the Reed Switch slightly, and then retighten
the Screw. Reattach the Hood (not shown) with the
#8 x 3/4" Screws (not shown) and with the #8 x 2"
Screws (not shown) if necessary. Run the treadmill
for a few minutes to check for a correct speed reading.
1/8 in.
15
Top
View
71
50
51
PROBLEM: The incline of the treadmill does not change correctly
SOLUTION: a. With the key in the console, press one of the Incline buttons. While the incline is changing, remove the key. After a few seconds, re-insert the key. The treadmill will automatically rise to the
maximum incline level and then return to the minimum level. This will recalibrate the incline system.
PROBLEM: The walking belt slows when walked on
SOLUTION: a. Use only a single-outlet surge suppressor that meets all of the specifications described on page 12.
b. If the walking belt is overtightened, treadmill performance may decrease and the walking belt may become damaged. Remove the key and UNPLUG
THE POWER CORD. Using the hex key, turn both
rear roller bolts counterclockwise, 1/4 of a turn.
When the walking belt is properly tightened, you
should be able to lift each edge of the walking belt
2 to 3 in. (5 to 7 cm) off the walking platform. Be
careful to keep the walking belt centered. Then,
plug in the power cord, insert the key, and run the
treadmill for a few minutes. Repeat until the walking belt is properly tightened.
b
2–3 in.
Rear Roller Bolts
c. If the walking belt still slows when walked on, see the front cover of this manual.
23
PROBLEM: The walking belt is off-center or slips when walked on
SOLUTION: a. If the walking belt is off-center, first remove the
key and UNPLUG THE POWER CORD. If the
walking belt has shifted to the left, use the hex
key to turn the left rear roller bolt clockwise 1/2 of a
turn; if the walking belt has shifted to the right,
turn the bolt counterclockwise 1/2 of a turn. Be
careful not to overtighten the walking belt. Then,
plug in the power cord, insert the key, and run the
treadmill for a few minutes. Repeat until the walking belt is centered.
b. If the walking belt slips when walked on, first remove the key and UNPLUG THE POWER CORD.
Using the hex key, turn both rear roller bolts clockwise, 1/4 of a turn. When the walking belt is correctly tightened, you should be able to lift each
edge of the walking belt 2 to 3 in. (5 to 7 cm) off
the walking platform. Be careful to keep the walking belt centered. Then, plug in the power cord, insert the key, and carefully walk on the treadmill for
a few minutes. Repeat until the walking belt is
properly tightened.
24
a
b
EXERCISE GUIDELINES
WARNING: Before beginning this
Burning Fat—To burn fat effectively, you must exercise at a low intensity level for a sustained period of
time. During the first few minutes of exercise, your
body uses carbohydrate calories for energy. Only after
the first few minutes of exercise does your body begin
to use stored fat calories for energy. If your goal is to
burn fat, adjust the intensity of your exercise until your
heart rate is near the lowest number in your training
zone. For maximum fat burning, exercise with your
heart rate near the middle number in your training
zone.
or any exercise program, consult your physician. This is especially important for persons
over age 35 or persons with pre-existing
health problems.
The pulse sensor is not a medical device.
Various factors may affect the accuracy of
heart rate readings. The pulse sensor is intended only as an exercise aid in determining
heart rate trends in general.
Aerobic Exercise—If your goal is to strengthen your
cardiovascular system, you must perform aerobic exercise, which is activity that requires large amounts of
oxygen for prolonged periods of time. For aerobic exercise, adjust the intensity of your exercise until your
heart rate is near the highest number in your training
zone.
These guidelines will help you to plan your exercise
program. For detailed exercise information, obtain a
reputable book or consult your physician. Remember,
proper nutrition and adequate rest are essential for
successful results.
WORKOUT GUIDELINES
EXERCISE INTENSITY
Warming Up—Start with 5 to 10 minutes of stretching
and light exercise. A warm-up increases your body
temperature, heart rate, and circulation in preparation
for exercise.
Whether your goal is to burn fat or to strengthen your
cardiovascular system, exercising at the proper intensity is the key to achieving results. You can use your
heart rate as a guide to find the proper intensity level.
The chart below shows recommended heart rates for
fat burning and aerobic exercise.
Training Zone Exercise—Exercise for 20 to 30 minutes with your heart rate in your training zone. (During
the first few weeks of your exercise program, do not
keep your heart rate in your training zone for longer
than 20 minutes.) Breathe regularly and deeply as you
exercise–never hold your breath.
Cooling Down—Finish with 5 to 10 minutes of stretching. Stretching increases the flexibility of your muscles
and helps to prevent post-exercise problems.
EXERCISE FREQUENCY
To find the proper intensity level, find your age at the
bottom of the chart (ages are rounded off to the nearest ten years). The three numbers listed above your
age define your “training zone.” The lowest number is
the heart rate for fat burning, the middle number is the
heart rate for maximum fat burning, and the highest
number is the heart rate for aerobic exercise.
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest between workouts. After a few months of regular exercise, you may complete up to five workouts each
week, if desired. Remember, the key to success is to
make exercise a regular and enjoyable part of your
everyday life.
25
PART LIST—Model No. PFTL97908.0
To locate the parts listed below, see the EXPLODED DRAWING near the end of this manual.
Key No. Qty.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
25
4
1
10
2
4
6
8
4
6
5
4
2
1
1
8
2
2
2
2
1
1
2
8
10
2
2
1
4
2
2
1
2
4
1
2
3
1
1
2
1
1
2
1
1
2
2
2
1
1
Description
Key No. Qty.
#8 x 3/4" Screw
#8 x 1" Tek Screw
Hex Key
3/8" x 2" Bolt
1/4" x 1 1/4" Bolt
3/8" x 5" Bolt
5/16" x 1 1/4" Bolt
3/8" Nut
3/8" Star Washer
5/16" Star Washer
#8 x 3/4" Tek Screw
#8 x 1/2" Screw
Base Pad Spacer
Latch Bracket
3/4" Reed Switch Screw
#8 x 3/4" Screw
1/4" x 1 1/4" Bolt
5/16" x 4 1/4" Bolt
3/8" x 1" Bolt
Rear Roller Bolt
3/8" x 1 3/4" Bolt
3/8" x 1 1/2" Bolt
3/8" x 1" Bolt
1/2" Ground Screw
#12 x 1 1/4" Screw
Motor Bolt
Cushion Stop
Reset/Off Circuit Breaker
Belt Guide Screw
1/4" Flat Washer
1/4" Lock Washer
Incline Stop Bracket
1/4" Star Washer
#8 x 1 3/4" Screw
Audio Wire
5/16" Flange Nut
Hood Clip
Upright Wire
Lift Frame Ground Wire
Front Isolator
Left Foot Rail
Warning Decal
Platform Cushion
Walking Platform
Walking Belt
Belt Guide
Cushion Track
Frame Spacer
1/4" x 1" Bolt
Magnet
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
26
1
2
1
1
1
1
2
1
1
1
1
1
2
1
1
3
1
1
1
1
1
1
1
1
1
1
2
1
1
1
4
2
1
2
3
9
1
2
1
4
1
1
1
1
1
1
1
4
1
1
Description
Front Roller/Pulley
15 1/2" Wire Tie
Storage Latch
Latch Knob
Right Foot Rail
Frame
Rear Roller Bracket
Rear Roller
Left Rear Foot
Right Rear Foot
Hood
Drive Belt
3/8" Jam Nut
Drive Motor
Lift Frame
Wire Tie
Controller Ground Wire
Power Cord
Power Cord Grommet
Controller
Reed Switch
Reed Switch Clip
Belly Pan
Left Upright
Incline Motor
Left Upright Spacer
Base Endcap
Right Upright
Right Upright Spacer
Latch Endcap
Base Pad
Caution Decal
Base
Wheel
Releasable Tie
8" Tie
Access Door
5/16" Cage Nut
Console
Bolt Spacer
Console Base
Plastic Tie
Incline Wire
Handrail Crossbar
Right Handrail
Left Handrail
Console Fan
Handrail Endcap
Left Accessory Tray
Key/Clip
R0808A
Key No. Qty.
101
102
103
104
1
2
4
1
Description
Key No. Qty.
Console Ground Wire
#8 x 1" Screw
Console Fan Screw
Lift Motor Spacer
105
106
107
108
2
1
1
1
Description
#8 x 2" Screw
Right Accessory Tray
Frame/Roller Ground Wire
5/32" Hex Key
Note: Specifications are subject to change without notice. See the back cover of this manual for information about
ordering replacement parts. *These parts are not illustrated.
27
28
20
31
25
30
57
24
59
36
58
3
20
16
18 42
34
108
16
25
41
31
60
30
25
24
18
44
27
102
16
43
47
34
46
57
36
29
40
12
107
45
25
25
16
16
17
8
55
48
51
4
54
47
27
102
25
16
43
50
56
53
29 25
17
46
40
12
49
25
8
48
80
4
EXPLODED DRAWING A—Model No. PFTL97908.0
R0808A
EXPLODED DRAWING B—Model No. PFTL97908.0
37
1
37
1
1
37
61
26
66
65
19
62
24
39
R0808A
71
64
12
11
15
24
70
72
11
11
105
11
73
105
29
19
67
24
68
69
28
EXPLODED DRAWING C—Model No. PFTL97908.0
10
10
32
21
7
7
74
63
75
22
104
63
7
6
76
9
83
4
8
84
90
13
81
2
82
85
7
77
23
2
8
38
14
84
10
13
81
2
4
86
30
78
8
77
9
82
81
4
93
38
10
23
81
8
52
8
R0808A
6
2 79
90
9
6
EXPLODED DRAWING D—Model No. PFTL97908.0
97
103
35
24
89
101
103
99
1
100
1
98
1
1
1
1
98
1
88
1
1
1
1
91
1
87
96
R0808A
33
1
5
94
106
1
98
1
33
92
95
98
31
1
88
1
5
ORDERING REPLACEMENT PARTS
To order replacement parts, please see the front cover of this manual. To help us assist you, be prepared to provide the following information when contacting us:
• the model number and serial number of the product (see the front cover of this manual)
• the name of the product (see the front cover of this manual)
• the key number and description of the replacement part(s) (see the PART LIST and the EXPLODED
DRAWING near the end of this manual)
LIMITED WARRANTY
ICON Health & Fitness, Inc. (ICON) warrants this product to be free from defects in workmanship and
material, under normal use and service conditions. The frame is warranted for a lifetime. The drive motor
is warranted for twenty-five (25) years from the date of purchase. Parts and labor are warranted for one
(1) year from the date of purchase.
This warranty extends only to the original purchaser. ICONʼs obligation under this warranty is limited to
repairing or replacing, at ICONʼs option, the product through one of its authorized service centers. All repairs for which warranty claims are made must be preauthorized by ICON. If the product is shipped to a
service center, freight charges to and from the service center will be the customerʼs responsibility. For
replacement parts shipped while the product is under warranty, the customer will be responsible for a
minimal handling charge. For in-home service, the customer will be responsible for a minimal trip charge.
This warranty does not extend to any damage to a product caused by or attributable to freight damage,
abuse, misuse, improper or abnormal usage, or repairs not provided by an ICON authorized service center; products used for commercial or rental purposes; or products used as store display models. No other
warranty beyond that specifically set forth above is authorized by ICON.
ICON is not responsible or liable for indirect, special, or consequential damages arising out of or in connection with the use or performance of the product; damages with respect to any economic loss, loss of
property, loss of revenues or profits, loss of enjoyment or use, or costs of removal or installation; or other
consequential damages of whatsoever nature. Some states do not allow the exclusion or limitation of incidental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties, and any implied warranties of
merchantability or fitness for a particular purpose are limited in their scope and duration to the terms set
forth herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the
above limitation may not apply to you.
This warranty gives you specific legal rights. You may also have other rights that vary from state to state.
ICON Health & Fitness, Inc., 1500 S. 1000 W., Logan, UT 84321-9813
Part No. 272459 R0808A
Printed in USA © 2008 ICON IP, Inc.