Savin 4027 Operating instructions

Paper type: OK Prince Eco G100(55kg), Paper Thickness=80 µm // Pages in book=184 // Print scale=81%
Gap (when printed at 81% scale) = Pages in book × Paper thickness / 2 = 7.360000 mm
Operating Instructions
General Settings Guide
1
Getting Started
2
Combined Function Operations
3
Document Server
4
User Tools (System Settings)
5
Troubleshooting
6
Remarks
7
Entering Text
8
Security
9
Specifications
Type for 4022/DSm622/LD122 AG/Aficio 2022
Type for 4027/DSm627/LD127 AG/Aficio 2027
Printed in China
EN USA B097-6507
For safe and correct use of this machine, please be sure to read the Safety Information in this
manual before you use it.
Paper type: OK Prince Eco G100(55kg), Paper Thickness=80 µm // Pages in book=184 // Print scale=81%
Gap (when printed at 81% scale) = Pages in book × Paper thickness / 2 = 7.360000 mm
Introduction
This manual describes detailed instructions on the operation and notes about the use of this machine.
To get maximum versatility from this machine all operators are requested to read this manual carefully
and follow the instructions. Please keep this manual in a handy place near the machine.
In accordance with IEC 60417, this machine uses the following symbols for the main power switch:
a means POWER ON.
c means STAND BY.
Important
Contents of this manual are subject to change without prior notice. In no event will the company be liable for direct, indirect, special, incidental, or consequential damages as a result of handling or operating the machine.
Notes:
Some illustrations in this manual might be slightly different from the machine.
Certain options might not be available in some countries. For details, please contact your local dealer.
Laser Safety:
CDRH Regulations
This equipment complies with requirements of 21 CFR subchapter J for class 1 laser products. This
equipment contains two 5- milliwatt, 760-800 nanometer wavelength, two GaAlAs laser diodes. This
equipment does not emit hazardous light, since the beam is totally enclosed during all customer modes
of operation and maintenance.
Warning:
Use of controls or adjustment or performance of procedures other than those specified in this manual
might result in hazardous radiation exposure.
Notes:
The model names of the machines do not appear in the following pages. Check the type of your machine before reading this manual. (For details, see P.15 “Machine Types”.)
•
Type 1: 4022/DSm622/LD122/Aficio 2022
•
Type 2: 4027/DSm627/LD127/Aficio 2027
•
Type 3: not available
Certain types might not be available in some countries. For details, please contact your local dealer.
Two kinds of size notation are employed in this manual. With this machine refer to the inch version.
For good copy quality, the supplier recommends that you use genuine toner from the supplier.
The supplier shall not be responsible for any damage or expense that might result from the use of parts
other than genuine parts from the supplier with your office products.
Power Source
120V, 60Hz, 12A or more
Please be sure to connect the power cord to a power source as above. For details about power source,
see P.134 “Power Connection”.
Copyright © 2003
RussianC3_ENgsg-F_FM.book Page i Monday, June 16, 2003 6:48 PM
Manuals for This Machine
The following manuals describe the operational procedures of this machine. For
particular functions, see the relevant parts of the manual.
Note
❒ Manuals provided are specific to machine type.
❒ Adobe Acrobat Reader is necessary to view the manuals as a PDF file.
❒ Two CD-ROMs are provided:
• CD-ROM 1 "Operating Instructions for Printer/Scanner"
• CD-ROM 2 "Scanner Driver & Document Management Utilities"
❖ General Settings Guide (this manual)
Provides an overview of the machine and describes System Settings (paper
trays, Key Operator Tools, etc.), Document Server functions, and troubleshooting.
Refer to this manual for Address Book procedures such as registering fax
numbers, e-mail addresses, and user codes.
❖ Network Guide (PDF file - CD-ROM1)
Describes procedures for configuring the machine and computers in a network environment.
❖ Copy Reference
Describes operations, functions, and troubleshooting for the machine's copier
function.
❖ Facsimile Reference <Basic Features>
Describes operations, functions, and troubleshooting for the machine's facsimile function.
❖ Facsimile Reference <Advanced Features>
Describes advanced functions and settings for key operators.
❖ Printer Reference 1
Describes system settings and operations for the machine's printer function.
❖ Printer Reference 2 (PDF file - CD-ROM1)
Describes operations, functions, and troubleshooting for the machine's printer function.
❖ Scanner Reference (PDF file - CD-ROM1)
Describes operations, functions, and troubleshooting for the machine's scanner function.
i
RussianC3_ENgsg-F_FM.book Page ii Monday, June 16, 2003 6:48 PM
❖ Manuals for DeskTopBinder V2 Lite
DeskTopBinder V2 Lite is a utility included on the CD-ROM labeled "Scanner
Driver & Document Management Utilities".
• DeskTopBinder V2 Lite Setup Guide (PDF file - CD-ROM2)
Describes installation of, and the operating environment for DeskTopBinder V2 Lite in detail. This guide can be displayed from the [Setup] display when DeskTopBinder V2 Lite is installed.
• DeskTopBinder V2 Lite Introduction Guide (PDF file - CD-ROM2)
Describes operations of DeskTopBinder V2 Lite and provides an overview
of its functions. This guide is added to the [Start] menu when DeskTopBinder V2 Lite is installed.
• Auto Document Link Guide (PDF file - CD-ROM2)
Describes operations and functions of Auto Document Link installed with
DeskTopBinder V2 Lite. This guide is added to the [Start] menu when
DeskTopBinder V2 Lite is installed.
❖ Manuals for ScanRouter V2 Lite
ScanRouter V2 Lite is a utility included on the CD-ROM labeled "Scanner
Driver & Document Management Utilities".
• ScanRouter V2 Lite Setup Guide (PDF file - CD-ROM2)
Describes installation of, settings, and the operating environment for ScanRouter V2 Lite in detail. This guide can be displayed from the [Setup] display when ScanRouter V2 Lite is installed.
• ScanRouter V2 Lite Management Guide (PDF file - CD-ROM2)
Describes delivery server management and operations, and provides an
overview of ScanRouter V2 Lite functions. This guide is added to the [Start]
menu when ScanRouter V2 Lite is installed.
❖ Other manuals
• PS3 Supplement (PDF file - CD-ROM1)
• Unix Supplement (Available from an authorized dealer, or as a PDF file on
our Web site.)
ii
RussianC3_ENgsg-F_FM.book Page iii Monday, June 16, 2003 6:48 PM
What You Can Do with This Machine
The following introduces the functions of this machine, and the relevant manuals containing detailed information about them.
Products marked with * are optional. For details about optional products, see
p.156 “Options”, or contact your local dealer.
Copier, Facsimile, Printer, and
Scanner Functions
Utilizing Stored Documents
GCKONN2J
GCKONN1J
This machine provides copier, facsimile*, printer*, and scanner* functions.
• You can make copies of originals.
With a finisher*, you can sort and
staple copies. See Copy Reference.
• You can send originals by fax and
receive faxes from other parties.
See Facsimile Reference <Basic Features> , and Facsimile Reference
<Advanced Features>.
• You can print documents created
using applications. See Printer Reference 1, Printer Reference 2.
• You can scan originals and send
the scan file to a computer. See
Scanner Reference.
• You can store file from originals
scanned by this machine, or file
sent from other computers, into
the machine's hard disk. You can
print and fax stored documents as
required. You can also change
print settings and print multiple
documents (Document Server).
See p.35 “Using the Document
Server”.
• With DeskTopBinder V2 Professional*/Lite, you can search,
check, print, and delete stored documents using your computer. You
can also retrieve stored documents
scanned in scanner mode. With
File Format Converter*, you can
even download documents stored
in copy and printer functions to
your computer. See Network Guide.
iii
RussianC3_ENgsg-F_FM.book Page iv Monday, June 16, 2003 6:48 PM
Paperless Fax Transmission
and Reception
Fax Transmission and
Reception Through the
Internet
Reception
GCKONN9J
GCKONN3J
• You can store received fax messages on the machine's hard disk, instead of printing them onto paper.
You can use DeskTopBinder V2
P r o f e s si o n a l * / L i t e o r a W e b
browser to check, print, delete, retrieve, or download documents using your computer (Storing
received documents). See Facsimile
Reference <Advanced Features>.
Transmission
GCKONN4J
• You can send documents created
using applications to another party's fax machine directly, without
performing a print job (LAN-Fax).
See Facsimile Reference <Advanced
Features>.
iv
You can send fax documents through
e-mail by specifying the recipient's email address (Internet Fax Transmission).
You can receive sent documents via
Internet Fax, or from computers (Internet Fax Reception). See Facsimile
Reference <Basic Features>
RussianC3_ENgsg-F_FM.book Page v Monday, June 16, 2003 6:48 PM
Using the Scanner in a
Network Environment
Administrating the
Machine/Protecting Documents
(Security Functions)
GCKONN5J
• You can send scanned documents
to other network computers using
e-mail (Sending stored scan file by
e-mail). See Scanner Reference.
• With ScanRouter V2 Professional*/Lite, you can save scanned
documents in specified destinations on network computers (File
storage). See Scanner Reference.
• You can send scanned documents
to other network folders (Scan to
Folder). See Scanner Reference
GCKONN6J
The security functions protect documents from being copied without
permission or unauthorized access
via the network. See p.145 “Security”.
❖ Security Functions
• Protecting stored documents
(setting passwords)
• Protecting file remaining in
memory
• Protecting against unauthorized access via phone line
• Authenticating administrator
(setting the key operator code).
See p.60 “Key Operator Code”.
❖ Extended Security Function
By setting a password, documents
are protected against unauthorized access. See p.60 “Extended
Security”.
v
RussianC3_ENgsg-F_FM.book Page vi Monday, June 16, 2003 6:48 PM
Monitoring the Machine Via
Computer
GCKONN7J
You can monitor machine status and
change settings using a computer.
• Using SmartNetMonitor for Admin, SmartNetMonitor for Client,
or a Web browser, you can use a
computer to view the machine's
status, such as to check on paper
quantities, or misfeeds, etc. See
Network Guide.
• You can also use a Web browser to
make network settings. See Network Guide.
• You can also use a Web browser to
register and manage items such as
user codes, fax numbers, e-mail
addresses, and folders in the Address Book. See the Web browser's
Help.
vi
RussianC3_ENgsg-F_FM.book Page vii Monday, June 16, 2003 6:48 PM
TABLE OF CONTENTS
Manuals for This Machine ...................................................................................... i
What You Can Do with This Machine.................................................................. iii
Copier, Facsimile, Printer, and Scanner Functions ................................................... iii
Utilizing Stored Documents ....................................................................................... iii
Paperless Fax Transmission and Reception............................................................. iv
Fax Transmission and Reception Through the Internet ............................................ iv
Using the Scanner in a Network Environment ........................................................... v
Administrating the Machine/Protecting Documents (Security Functions) .................. v
Monitoring the Machine Via Computer...................................................................... vi
Notice ......................................................................................................................1
Copyrights and Trademarks .................................................................................3
Trademarks ................................................................................................................3
Information about Installed Software.......................................................................... 4
How to Read This Manual .....................................................................................9
Safety Information ............................................................................................... 10
Safety During Operation........................................................................................... 10
Positions of Labels and Hallmarks forR
RWARNING and RCAUTION............. 12
ENERGY STAR Program ..................................................................................... 13
Machine Types ..................................................................................................... 15
1. Getting Started
Guide to Components ......................................................................................... 17
External Options....................................................................................................... 19
Internal Options........................................................................................................ 20
Control Panel........................................................................................................ 21
Display Panel ........................................................................................................... 23
Turning On the Power ......................................................................................... 24
Turning On the Main Power ..................................................................................... 24
Turning On the Power .............................................................................................. 24
Turning Off the Power .............................................................................................. 25
Turning Off the Main Power ..................................................................................... 25
Saving Energy .......................................................................................................... 26
2. Combined Function Operations
Changing Modes .................................................................................................. 27
Multi-Access......................................................................................................... 29
vii
RussianC3_ENgsg-F_FM.book Page viii Monday, June 16, 2003 6:48 PM
3. Document Server
Relationship between Document Server and Other Functions ....................... 33
Document Server Display ........................................................................................ 34
Using the Document Server................................................................................ 35
Storing Data ............................................................................................................. 35
Changing a Stored Document's File Name, User Name, or Password.................... 38
Selecting a Document .............................................................................................. 38
Searching for Stored Documents ............................................................................. 39
Printing Stored Documents ...................................................................................... 40
Deleting Stored Documents ..................................................................................... 43
Viewing Stored Documents Using a Web Browser .................................................. 44
Downloading Stored Documents.............................................................................. 44
Settings for the Document Server...................................................................... 45
4. User Tools (System Settings)
User Tools Menu (System Settings)................................................................... 47
Accessing User Tools (System Settings) .......................................................... 50
Changing Default Settings ....................................................................................... 50
Exiting User Tools .................................................................................................... 50
Settings You Can Change with User Tools ....................................................... 51
General Features ..................................................................................................... 51
Tray Paper Settings ................................................................................................. 55
Timer Settings .......................................................................................................... 58
Key Operator Tools .................................................................................................. 59
Address Book....................................................................................................... 67
Registering Destination Information ......................................................................... 68
Registering Sender Information ............................................................................... 69
User Codes ........................................................................................................... 70
Registering a New User Code.................................................................................. 70
Changing a User Code............................................................................................. 72
Deleting a User Code............................................................................................... 73
Displaying the Counter for Each User Code ............................................................ 73
Printing the Counter for Each User Code................................................................. 74
Clearing the Number of Prints.................................................................................. 75
Fax Destination .................................................................................................... 76
Registering a Fax Destination .................................................................................. 77
Changing a Registered Fax Destination .................................................................. 79
Deleting a Registered Fax Destination..................................................................... 81
E-mail Destination................................................................................................ 82
Registering an E-mail Destination ............................................................................ 82
Changing a Registered E-mail Destination .............................................................. 84
Deleting a Registered E-mail Destination ................................................................ 84
Registering Folders ............................................................................................. 85
Using SMB to Connect............................................................................................. 85
Using FTP to Connect.............................................................................................. 89
Registering a Protection Code ........................................................................... 93
Registering a Protection Code To a Single User ..................................................... 93
Registering a Protection Code To a Group User ..................................................... 94
viii
RussianC3_ENgsg-F_FM.book Page ix Monday, June 16, 2003 6:48 PM
Registering Destinations to a Group ................................................................. 95
Registering a New Group ......................................................................................... 95
Registering Destinations to a Group ........................................................................ 96
Removing a Destination from a Group ..................................................................... 96
Displaying Destinations Registered in Groups......................................................... 97
Changing a Group Name ......................................................................................... 97
Deleting a Group ...................................................................................................... 98
Registering the Transfer Request ...................................................................... 99
Registering a Transfer Station/Receiving Station .................................................... 99
Changing a Registered Transfer Station/Receiving Station ...................................101
Deleting a Registered Transfer Station/Receiving Station .....................................102
Programming/Changing LDAP Server ............................................................. 103
Programming an LDAP Server...............................................................................103
Changing an LDAP Server.....................................................................................105
5. Troubleshooting
If Your Machine Does Not Operate As You Want............................................ 107
General ..................................................................................................................107
Document Server ...................................................................................................109
B Loading Paper ............................................................................................... 110
Loading Paper into Paper Trays ............................................................................110
Loading Paper into Large Capacity Tray (optional)................................................111
D Adding Toner................................................................................................. 113
Removing Toner................................................................................................. 114
Inserting Toner................................................................................................... 115
x Clearing Misfeeds ......................................................................................... 116
Changing the Paper Size................................................................................... 122
Changing the Paper Size of the Paper Tray .........................................................122
d Adding Staples.............................................................................................. 125
500-Sheet Finisher.................................................................................................125
1000-Sheet Finisher...............................................................................................126
Removing Jammed Staples .............................................................................. 128
500-Sheet Finisher.................................................................................................128
1000-Sheet Finisher...............................................................................................129
6. Remarks
Dos and Don'ts................................................................................................... 131
Toner ................................................................................................................... 132
Handling Toner.......................................................................................................132
Toner Storage ........................................................................................................132
Used Toner ............................................................................................................132
Where to Put Your Machine .............................................................................. 133
Machine Environment ............................................................................................133
Moving....................................................................................................................134
Power Connection..................................................................................................134
Access to the Machine ...........................................................................................135
ix
RussianC3_ENgsg-F_FM.book Page x Monday, June 16, 2003 6:48 PM
Maintaining Your Machine ................................................................................ 136
Cleaning the Exposure Glass.................................................................................136
Cleaning the Exposure Glass Cover ...................................................................... 136
Cleaning the Auto Document Feeder.....................................................................136
Replacing the Photo Conductor Unit (PCU) ................................................... 137
Other Functions ................................................................................................. 140
Inquiry ....................................................................................................................140
Changing the Display Language ............................................................................140
Counter ............................................................................................................... 141
Displaying the Total Counter..................................................................................141
7. Entering Text
Entering Text ...................................................................................................... 143
Available Characters ..............................................................................................143
Keys .......................................................................................................................143
How to Enter Text ..................................................................................................144
8. Security
Security............................................................................................................... 145
Primary Security Functions ....................................................................................145
Extended Security Function ...................................................................................145
Temporarily Disabling Document Security .............................................................147
Operating Environment and Notes................................................................... 148
Operating Environment .......................................................................................... 148
For Administrator.................................................................................................... 148
For User .................................................................................................................149
9. Specifications
Main Unit............................................................................................................. 151
Options ............................................................................................................... 156
Exposure Glass Cover ...........................................................................................156
Auto Document Feeder .......................................................................................... 156
500-Sheet Finisher.................................................................................................157
1000-Sheet Finisher...............................................................................................158
Shift Sort Tray ........................................................................................................159
Duplex Unit.............................................................................................................159
Bypass Tray ...........................................................................................................160
Bridge Unit .............................................................................................................160
Internal Tray 2 (1 bin tray)......................................................................................160
Large Capacity Tray...............................................................................................161
Paper Tray Unit ......................................................................................................161
Copy Paper ......................................................................................................... 163
Recommended Paper Sizes and Types.................................................................163
Envelopes .............................................................................................................. 166
Unusable Paper .....................................................................................................169
Paper Storage ........................................................................................................169
INDEX....................................................................................................... 170
x
RussianC3_ENgsg-F_FM.book Page 1 Monday, June 16, 2003 6:48 PM
Notice
Notice To Wireless LAN Interface (option) Users
Notes to users in the United States of America
Notice:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired
operation.
Warning
Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
Note to users in Canada
Note:
This Class B digital apparatus complies with Canadian ICES-003.
Operation is subject to the following two conditions:
(1) This device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of the
device.
1
RussianC3_ENgsg-F_FM.book Page 2 Monday, June 16, 2003 6:48 PM
IEEE 802.11b Interface Kit Type B:
This device complies with RSS-210 of Industry Canada.
The term “IC:” before the certification/registration number only signifies that
the Industry Canada technical specifications were met.
To prevent radio interference to the licensed service, this device is intended to
be operated indoors and away from windows to provide maximum shielding.
Equipment (or its transmit antenna) that is installed outdoors is subject to licensing.
To reduce potential radio interference to other users, the antenna type and its
gain should be so chosen that the equivalent isotropically radiated power (EIRP)
is not more than that required for successful communication.
This device has been designed to operate with an antenna having a maximum
gain of [0.45] dBi. Antenna having a higher gain is strictly prohibited per regulations of Industry Canada. The required antenna impedance is [50] ohms.
Remarque concernant les utilisateurs au Canada
Avertissement:
Cet appareil numérique de la classe B est conforme á la norme NMB-003 du Canada.
L'utilisation de ce dispositif est autorisée seulement aux conditions suivantes: (1)
il ne doit pas produire de brouillage et (2) l'utilisateur du dispositif doit être prêt
á accepter tout brouillage radioélectrique reçu, même si ce brouillage est susceptible de compromettre le fonctionnement du dispositif.
IEEE 802.11b Interface Kit Type B:
Ce dispositif est conforme á la norme CNR-210 d'Industrie Canada.
L'expression «IC:» avant le numéro d'homologation/enregistrement signifie
seulement que les spécifications techniques d'Industrie Canada ont été respectées.
Pour empêcher que cet appareil cause du brouillage au service faisant l'objet
d'une licence, il doit être utilisé á l'intérieur et devrait être placé loin des fenêtres
afin de fournir un écran de blindage maximal.
Si le matériel (ou son antenne d'emission) est installe á l'extérieur, il doit faire
l'objet d'une licence.
Afin de réduire le risque d'interférence aux autres utilisateurs, le type d'antenne
et son gain doivent être choisis de façon á ce que la puissance isotrope rayonnée
équivalente (p.i.r.e.) ne soit pas supérieure au niveau requis pour obtenir une
communication satisfaisante.
Ce dispositif a été conçu pour fonctionner avec une antenne ayant un gain maximal de [0.45] dBi.Une antenne ayant un gain plus élevé est strictement interdite
par les réglements d'Industrie Canada.L'impédance d'antenne requise est [50]
ohms.
2
RussianC3_ENgsg-F_FM.book Page 3 Monday, June 16, 2003 6:48 PM
Copyrights and Trademarks
Trademarks
Microsoft®, Windows® and Windows NT® are registered trademarks of Microsoft Corporation in the United States and/or other countries.
Acrobat® is a registered trademark of Adobe Systems Incorporated.
Bluetooth™ is a trademark of the Bluetooth SIG, Inc. (Special Interest Group)
and is used by RICOH Company Limited under license.
Copyright ©2001 Bluetooth SIG, Inc.
The Bluetooth Trademarks are owned by Bluetooth SIG, Inc. USA
Other product names used herein are for identification purposes only and might
be trademarks of their respective companies. We disclaim any and all right in
those marks.
Other product names used herein are for identification purposes only and might
be trademarks of their respective companies. We disclaim any and all right in
those marks.
The proper names of the Windows operating systems are as follows:
• The product name of Windows® 95 is Microsoft® Windows® 95
• The product name of Windows® 98 is Microsoft® Windows® 98
• The product name of Windows® Me is Microsoft® Windows® Millennium
Edition (Windows Me)
• The product names of Windows® 2000 are as follows:
Microsoft® Windows® 2000 Advanced Server
Microsoft® Windows® 2000 Server
Microsoft® Windows® 2000 Professional
• The product names of Windows® XP are as follows:
Microsoft® Windows® XP Professional
Microsoft® Windows® XP Home Edition
• The product names of Windows Server™ 2003 are as follows:
Microsoft® Windows Server™ 2003 Standard Edition
Microsoft® Windows Server™ 2003 Enterprise Edition
Microsoft® Windows Server™ 2003 Web Edition
• The product names of Windows® NT are as follows:
Microsoft® Windows NT® Server 4.0
Microsoft® Windows NT® Workstation 4.0
3
RussianC3_ENgsg-F_FM.book Page 4 Monday, June 16, 2003 6:48 PM
Information about Installed Software
Expat
• The software including controller, etc. (hereinafter "software") installed on
this product uses the expat Version 1.95.2 (hereinafter "expat") under the conditions mentioned below.
• The product manufacturer provides warranty and support to the software of
the product including the expat, and the product manufacturer makes the initial developer and copyright holder of the expat, free from these obligations.
• Information relating to the expat is available at:
http://expat.sourceforge.net/
Copyright © 1998, 1999, 2000 Thai Open Source Software Center, Ltd. and Clark
Cooper.
Permission is hereby granted, free of charge, to any person obtaining a copy of
this software and associated documentation files (the "Software"), to deal in the
Software without restriction, including without limitation the rights to use,
copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the
Software, and to permit persons to whom the Software is furnished to do so, subject to the following conditions:
The above copyright notice and this permission notice shall be included in all
copies or substantial portions of the Software.
THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY
KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT,
TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION
WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
NetBSD
1. Copyright Notice of NetBSD
For all users to use this product:
This product contains NetBSD operating system:
For the most part, the software constituting the NetBSD operating system is not
in the public domain; its authors retain their copyright.
The following text shows the copyright notice used for many of the NetBSD
source code. For exact copyright notice applicable for each of the files/binaries,
the source code tree must be consulted.
A full source code can be found at http://www.netbsd.org/.
Copyright © 1999, 2000 The NetBSD Foundation, Inc.
All rights reserved.
4
RussianC3_ENgsg-F_FM.book Page 5 Monday, June 16, 2003 6:48 PM
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
A Redistributions of source code must retain the above copyright notice, this list
of conditions and the following disclaimer.
B Redistributions in binary form must reproduce the above copyright notice,
this list of conditions and the following disclaimer in the documentation
and/or other materials provided with the distribution.
C All advertising materials mentioning features or use of this software must
display the following acknowledgment:
This product includes software developed by The NetBSD Foundation, Inc.
and its contributors.
D Neither the name of The NetBSD Foundation nor the names of its contributors may be used to endorse or promote products derived from this software
without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE NETBSD FOUNDATION, INC. AND
CONTRIBUTORS ''AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS
BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,
EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
Sablotron
Sablotron (Version 0.82) Copyright © 2000 Ginger Alliance Ltd. All Rights Reserved
a) The application software installed on this product includes the Sablotron software Version 0.82 (hereinafter, “Sablotron 0.82”), with modifications made by
the product manufacturer. The original code of the Sablotron 0.82 is provided by
Ginger Alliance Ltd., the initial developer, and the modified code of the Sablotron 0.82 has been derived from such original code provided by Ginger Alliance Ltd.
b) The product manufacturer provides warranty and support to the application
software of this product including the Sablotron 0.82 as modified, and the product manufacturer makes Ginger Alliance Ltd., the initial developer of the Sablotron 0.82, free from these obligations.
c) The Sablotron 0.82 and the modifications thereof are made available under the
terms of Mozilla Public License Version 1.1 (hereinafter, “MPL 1.1”), and the application software of this product constitutes the “Larger Work” as defined in
MPL 1.1. The application software of this product except for the Sablotron 0.82
as modified is licensed by the product manufacturer under separate agreement(s).
5
RussianC3_ENgsg-F_FM.book Page 6 Monday, June 16, 2003 6:48 PM
d) The source code of the modified code of the Sablotron 0.82 is available at: http://support-download.com/services/device/sablot/notice082.html
e) The source code of the Sablotron software is available at: http://www.gingerall.com
f) MPL 1.1 is available at: http://www.mozilla.org/MPL/MPL-1.1.html
Authors Name List
All product names mentioned herein are trademarks of their respective owners.
The following notices are required to satisfy the license terms of the software
that we have mentioned in this document:
• This product includes software developed by the University of California,
Berkeley and its contributors.
• This product includes software developed by Jonathan R. Stone for the NetBSD Project.
• This product includes software developed by the NetBSD Foundation, Inc.
and its contributors.
• This product includes software developed by Manuel Bouyer.
• This product includes software developed by Charles Hannum.
• This product includes software developed by Charles M. Hannum.
• This product includes software developed by Christopher G. Demetriou.
• This product includes software developed by TooLs GmbH.
• This product includes software developed by Terrence R. Lambert.
• This product includes software developed by Adam Glass and Charles Hannum.
• This product includes software developed by Theo de Raadt.
• This product includes software developed by Jonathan Stone and Jason R.
Thorpe for the NetBSD Project.
• This product includes software developed by the University of California,
Lawrence Berkeley Laboratory and its contributors.
• This product includes software developed by Christos Zoulas.
• This product includes software developed by Christopher G. Demetriou for
the NetBSD Project.
• This product includes software developed by Paul Kranenburg.
• This product includes software developed by Adam Glass.
• This product includes software developed by Jonathan Stone.
• This product includes software developed by Jonathan Stone for the NetBSD
Project.
• This product includes software developed by Winning Strategies, Inc.
• This product includes software developed by Frank van der Linden for the
NetBSD Project.
• This product includes software developed for the NetBSD Project by Frank
van der Linden
6
RussianC3_ENgsg-F_FM.book Page 7 Monday, June 16, 2003 6:48 PM
• This product includes software developed for the NetBSD Project by Jason R.
Thorpe.
• The software was developed by the University of California, Berkeley.
• This product includes software developed by Chris Provenzano, the University of California, Berkeley, and contributors.
JPEG LIBRARY
• The software installed on this product is based in part on the work of the Independent JPEG Group.
SASL
CMU libsasl
Tim Martin
Rob Earhart
Rob Siemborski
Copyright © 2001 Carnegie Mellon University. All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
A Redistributions of source code must retain the above copyright notice, this list
of conditions and the following disclaimer.
B Redistributions in binary form must reproduce the above copyright notice,
this list of conditions and the following disclaimer in the documentation
and/or other materials provided with the distribution.
C The name "Carnegie Mellon University" must not be used to endorse or promote products derived from this software without prior written permission.
For permission or any other legal details, please contact:
Office of Technology Transfer
Carnegie Mellon University
5000 Forbes Avenue
Pittsburgh, PA 15213-3890
(412) 268-4387, fax: (412) 268-7395
tech-transfer@andrew.cmu.edu
D Redistributions of any form whatsoever must retain the following acknowledgment:
"This product includes software developed by Computing Services at Carnegie Mellon University (http://www.cmu.edu/computing/)."
CARNEGIE MELLON UNIVERSITY DISCLAIMS ALL WARRANTIES WITH REGARD TO THIS SOFTWARE, INCLUDING ALL IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS, IN NO EVENT SHALL CARNEGIE MELLON UNIVERSITY BE LIABLE FOR ANY SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES WHATSOEVER RESULTING
FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF OR
IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
7
RussianC3_ENgsg-F_FM.book Page 8 Monday, June 16, 2003 6:48 PM
MD4
Copyright © 1990-2, RSA Data Security, Inc. All rights reserved.
License to copy and use this software is granted provided that it is identified as
the "RSA Data Security, Inc. MD4 Message-Digest Algorithm" in all material
mentioning or referencing this software or this function.
License is also granted to make and use derivative works provided that such
works are identified as "derived from the RSA Data Security, Inc. MD4 MessageDigest Algorithm" in all material mentioning or referencing the derived work.
RSA Data Security, Inc. makes no representations concerning either the merchantability of this software or the suitability of this software for any particular
purpose. It is provided "as is" without express or implied warranty of any kind.
These notices must be retained in any copies of any part of this documentation
and/or software.
MD5
Copyright © 1991-2, RSA Data Security, Inc. Created 1991. All rights reserved.
License to copy and use this software is granted provided that it is identified as
the "RSA Data Security, Inc. MD5 Message-Digest Algorithm" in all material
mentioning or referencing this software or this function.
License is also granted to make and use derivative works provided that such
works are identified as "derived from the RSA Data Security, Inc. MD5 MessageDigest Algorithm" in all material mentioning or referencing the derived work.
RSA Data Security, Inc. makes no representations concerning either the merchantability of this software or the suitability of this software for any particular
purpose. It is provided "as is" without express or implied warranty of any kind.
These notices must be retained in any copies of any part of this documentation
and/or software.
8
RussianC3_ENgsg-F_FM.book Page 9 Monday, June 16, 2003 6:48 PM
How to Read This Manual
Symbols
This manual uses the following symbols:
R WARNING:
This symbol indicates a potentially hazardous situation that might result in
death or serious injury if you misuse the machine by not following these instructions under this symbol. Be sure to read these instructions, all of which are included in the Safety Information section in the General Settings Guide.
R CAUTION:
This symbol indicates a potentially hazardous situation that might result in minor or moderate injury or property damage not involving bodily injury, if you
misuse the machine by not following these instructions under this symbol. Be
sure to read the instructions, all of which are included in the Safety Information
section in the General Settings Guide.
* The above statements are for your safety.
Important
If this instruction is not followed, paper might be misfed, originals damaged, or
data lost. Be sure to read this.
Preparation
This symbol indicates the prior knowledge or preparation required before operation.
Note
This symbol indicates precautions for operation, or actions to take following
mal-operation.
Limitation
This symbol indicates numerical limits, functions that cannot be used together,
or conditions under which a particular function cannot be used.
Reference
This symbol indicates where further relevant information can be found.
[
]
Keys that appear on the machine's display panel.
{
}
Keys built into the machine's control panel.
9
RussianC3_ENgsg-F_FM.book Page 10 Monday, June 16, 2003 6:48 PM
Safety Information
When using this machine, the following safety precautions should always be followed.
Safety During Operation
In this manual, the following important symbols are used:
R WARNING:
Indicates a potentially hazardous situation which, if instructions
are not followed, could result in death or serious injury.
R CAUTION:
Indicates a potentially hazardous situation which, if instructions are not
followed, may result in minor or moderate injury or damage to property.
R WARNING:
• Connect the power cord directly into a wall outlet and never use an extension cord.
• Disconnect the power plug (by pulling the plug, not the cable) if the
power cable or plug becomes frayed or otherwise damaged.
• To avoid hazardous electric shock or laser radiation exposure, do not
remove any covers or screws other than those specified in this manual.
• Turn off the power and disconnect the power plug (by pulling the plug,
not the cable) if any of the following occurs:
• You spill something into the machine.
• You suspect that your machine needs service or repair.
• The external housing of your machine has been damaged.
• Do not incinerate spilled toner or used toner. Toner dust might ignite
when exposed to an open flame.
• Disposal can take place at our authorized dealer.
• Dispose of the used toner bottle in accordance with the local regulations.
10
RussianC3_ENgsg-F_FM.book Page 11 Monday, June 16, 2003 6:48 PM
R CAUTION:
• Protect the machine from dampness or wet weather, such as rain and snow.
• Unplug the power cord from the wall outlet before you move the machine.
While moving the machine, you should take care that the power cord will not
be damaged under the machine.
• When you disconnect the power plug from the wall outlet, always pull the
plug (not the cable).
• Do not allow paper clips, staples, or other small metallic objects to fall inside
the machine.
• Keep toner (used or unused) and toner bottle out of the reach of children.
• For environmental reasons, do not dispose of the machine or expended
supply waste at household waste collection points. Disposal can take place
at an authorized dealer.
• The inside of the machine could be very hot. Do not touch the parts with a
label indicating the “hot surface”. Otherwise, an injury might occur.
11
RussianC3_ENgsg-F_FM.book Page 12 Monday, June 16, 2003 6:48 PM
Positions of Labels and Hallmarks
forR
RWARNING and RCAUTION
This machine has labels for RWARNING and RCAUTION at the positions
shown below. For safety, please follow the instructions and handle the machine
as indicated.
ZLEH010J
12
RussianC3_ENgsg-F_FM.book Page 13 Monday, June 16, 2003 6:48 PM
ENERGY STAR Program
As an ENERGY STAR Partner, we have determined
that this machine model meets the ENERGY STAR
Guidelines for energy efficiency.
The ENERGY STAR Guidelines intend to establish an international energy-saving system for
developing and introducing energy-efficient office equipment to deal with environmental issues, such as global warming.
When a product meets the ENERGY STAR Guidelines for energy efficiency, the Partner shall
place the ENERGY STAR logo onto the machine model.
This product was designed to reduce the environmental impact associated with office equipment by means of energy-saving features, such as Low-power mode.
❖ Low-Power mode and Off mode or Sleep mode
This product automatically lowers its power consumption when it is not operated for a fixed time (standard setting time: 1 minute). This is called “Off
mode” on a single function copying machine, and “Sleep mode” on a multiple
function machine equipped with optional facsimile and printing functions.
• Off mode: Same as the condition when the operation switch is turned off.
• Sleep mode: Same as the condition when the operation switch is turned off.
Receiving fax messages and printing from a computer are possible.
If you want to operate this product while it is in either of these modes, do one
of the following:
• Turn on the operation switch.
• Place an original in the Auto Document Feeder (ADF).
• Lift and lower the exposure glass cover or the ADF.
The default interval before entering Off mode or Sleep mode can be adjusted.
To change it, see p.58 “Auto Off Timer”.
The ENERGY STAR Program establishes two modes which lower the power
consumption of the product when it is not operated for a fixed time. These
modes are the Low-power mode and the Off mode or Sleep mode. This product has only one mode, the Off mode or Sleep mode. This mode meets the requirements of both the Low-power mode and Off mode or Sleep mode. In this
manual, the Off mode is called the Auto Off mode.
13
RussianC3_ENgsg-F_FM.book Page 14 Monday, June 16, 2003 6:48 PM
❖ Duplex Priority
The ENERGY STAR Program recommends the duplex function. By conserving paper resources this function is less of a burden to the environment. For
applicable machines, duplex function (one-sided originals→ two-sided copies) is selected preferentially when the operation switch or the main power
switch is turned on, the {Energy Saver}
} key is pressed, or the machine resets
automatically.
Reference
To change the settings of the Duplex Priority mode, see “Duplex Mode Priority”in “General Features 2/4”, Copy Reference.
Specifications
Low- Power mode, Off
Mode
Power consumption
Default interval
Recovery time
Duplex Priority
6W
1 minute
10 seconds or less
1 Sided→2 Sided
❖ Recycled Paper
In accordance with the ENERGY STAR Program, we recommend use of environmentally friendly recycled paper. Please contact your sales representative
for recommended paper.
14
RussianC3_ENgsg-F_FM.book Page 15 Monday, June 16, 2003 6:48 PM
Machine Types
This machine comes in three models which vary in copy speed. To ascertain
which model you have, see the inside front cover.
Copy speed
Type 1
Type 2
Type 3
22 copies/minute
(A4K, 81/2" × 11"K)
27 copies/minute
(A4K, 81/2" × 11"K)
32 copies/minute
(A4K, 81/2" × 11"K)
15
RussianC3_ENgsg-F_FM.book Page 16 Monday, June 16, 2003 6:48 PM
16
RussianC3_ENgsg-F_FM.book Page 17 Monday, June 16, 2003 6:48 PM
1. Getting Started
Guide to Components
1. Exposure glass cover (optional) or
Auto Document Feeder (ADF) (optional)
Lower the exposure glass cover over
originals placed on the exposure glass. If
you have the ADF, load a stack of originals here. They will be fed automatically,
one by one.
(The illustration shows the ADF.)
2. Exposure glass
Place originals face down.
3. Internal tray
Copied, printed paper or fax messages
are delivered here.
4. Ventilation holes
Prevents overheating. Do not obstruct
the ventilation holes by placing anything
near it or leaning objects against it. If the
machine overheats, a fault might occur.
5. Main power switch
If the machine does not operate after
turning on the operation switch, check
the main power switch is turned on. If it
is off, turn it on.
6. Main power indicator
This indicator lights when the main power switch is turned on, and goes off when
the switch is turned off.
7. On indicator
This indicator lights when the operation
switch is turned on, and goes off when
the switch is turned off.
8. Operation switch
Press this switch to turn the power on
(the On indicator lights up). To turn the
power off, press this switch again (the On
indicator goes off).
17
RussianC3_ENgsg-F_FM.book Page 18 Monday, June 16, 2003 6:48 PM
Getting Started
1
9. Control panel
12. Front cover
See p.21 “Control Panel”.
Open to access the inside of the machine.
10. Remove Paper Indicator
13. Paper tray
The indicator lights when paper is delivered to the internal tray 2 (1 bin tray).
When paper is removed from the internal
tray 2, the indicator goes off.
Load paper. See p.110 “B Loading Paper”.
Note
❒ Internal tray 2 (1 bin tray) is optional.
11. Duplex unit (Unit for two-sided
copies) (optional)
Makes two-sided copies.
See p.19 “External Options”
1. Bypass tray (optional)
See p.19 “External Options”
2. Paper tray cover
Open this cover to remove jammed paper.
3. Lower right cover
Open this cover to remove jammed paper.
18
14. Paper tray 2
Use when copying onto OHP transparencies, label paper (adhesive labels), translucent paper, postcards, envelopes and
custom size paper. See p.110 “B Loading
Paper”.
15. Paper tray unit (optional)
Load paper. See p.110 “B Loading Paper”, p.19 “External Options”.
RussianC3_ENgsg-F_FM.book Page 19 Monday, June 16, 2003 6:48 PM
Guide to Components
External Options
1
1. 500-sheet finisher *1
8. Paper tray unit
Sorts, stacks and staples copies.
Consists of two paper trays.
2. Bridge unit
9. Large Capacity Tray (LCT)
Relays copies to the finisher.
Holds up to 2000 sheets of paper.
3. Exposure glass cover
10. Bypass tray
Lower this cover over originals.
Load a stack of originals. They will feed
in automatically.
Use when copying onto OHP transparencies, label paper (adhesive labels), translucent paper, postcards, envelopes and
custom size paper. See “Copying from
the Bypass tray”, Copy Reference.
5. Internal tray 2 (1 bin tray)
11. Duplex unit
4. ADF
If you select this as the output tray, copies
are delivered face down.
6. 1000-sheet finisher *1
Sorts, stacks and staples copies.
*1
: Finisher upper tray
*2
: Finisher shift tray
Use to make two-sided copies.
12. Inter change unit
Required when installing the internal
tray 2 (1 bin tray) and duplex unit.
7. Shift sort tray
Sorts and stacks copies.
19
RussianC3_ENgsg-F_FM.book Page 20 Monday, June 16, 2003 6:48 PM
Getting Started
Internal Options
A
1
B
C
D
E
F
G
H
I
HDD
Allows you to use the Document Server function.
Fax unit
Allows you to use the facsimile function.
Printer/Scanner unit *2
Allows you to use the printer and scanner functions.
IEEE 1394 interface board *3
Connects to an IEEE 1394 cable.
Bluetooth *3
Allows you to expand the interface.
File Format Converter *3
Allows you to download documents from the Document Server stored by
copier and printer functions. See p.44 “Downloading Stored Documents”.
IEEE 802.1b Wireless LAN Board *3
You can install a wireless LAN interface.
USB 2.0 Interface Board *3
Allows you to connect a variety of external devices.
User account enhance unit
Allows you to increase the number of user codes.
Note
❒ You can install only one interface board from items D to H.
*1
*2
*3
20
You cannot install two finishers simultaneously.
The 128 MB memory and network board are included.
You cannot install two or more of the options below:
IEEE 1394 interface board, IEEE 802.1b wireless LAN board, USB 2.0 Interface Board,
Bluetooth, file format converter.
RussianC3_ENgsg-F_FM.book Page 21 Monday, June 16, 2003 6:48 PM
Control Panel
Control Panel
This illustration shows the control panel of a machine that has all options fully
installed.
1
ZLFS280N
1. Screen contrast knob
3. {User Tools/Counter}} key
Adjusts display panel brightness.
• User Tools
Press to change defaults and conditions to meet your requirements. See
p.50 “Accessing User Tools (System
Settings)”.
• Counter
Press to check or print the counter value. See p.141 “Counter”.
• Inquiry
Press to check where to contact for
machine repairs and ordering toner.
See p.140 “Inquiry”
2. Indicators
Show errors and machine status.
• d: Add Staple indicator. See p.125
“d Adding Staples”.
• D: Add Toner indicator. See p.113
“D Adding Toner”.
• B: Load Paper indicator. See p.110
“B Loading Paper”.
• L: Service Call indicator
• M: Open Cover indicator
• x: Misfeed indicator. See p.116 “x
Clearing Misfeeds”.
• m: Data In indicator. See “Control
Panel”, Printer Reference 1.
• Communicating: Communicating indicator. See “Control Panel”, Facsimile
Reference <Basic Features>.
• i: Confidential File indicator. See
“Control Panel”, Facsimile Reference
<Basic Features>.
• Receiving File: Receiving File indicator. See “Control Panel”, Facsimile Reference <Basic Features>.
4. Display panel
Displays operation status, error messages, and function menus.
5. {Check Modes}} key
Press to check settings.
6. { Program}} key (copier/facsimile/scanner mode)
Press to register frequently used settings,
or recall registered settings.
7. {Clear Modes}} key
Press to clear previous copy job settings.
21
RussianC3_ENgsg-F_FM.book Page 22 Monday, June 16, 2003 6:48 PM
Getting Started
8. {Energy Saver}} key
16. Number keys
Press to switch to and from Energy Saver
mode. See p.26 “Energy Saver Mode”.
Use to enter the numbers for copies, fax
numbers and data for the selected function.
9. { Interrupt}} key (copier/scanner
mode)
1
Press to make interrupt copies during
copying or scanning. See “Interrupt
Copy”, Copy Reference.
10. Main power indicator and On
indicator
The main power indicator goes on when
you turn on the main power switch.
The On indicator lights when the power
is on.
Important
❒ Do not turn off the main power
switch while the power indicator is
lit or blinking. Doing so may damage the hard disk.
11. Operation switch
Press to turn the power on (the On indicator goes on). To turn the power off,
press again (the On indicator goes off).
12. {Sample Copy}} key
Press to make a single set of copies or
prints to check print quality before making multiple sets.
13. {Start}} key
Press to start copying. Start scanning or
printing documents stored using the
Document Server function.
14. {Clear/Stop}} key
• Clear
Press to delete a number entered.
• Stop
Press to stop a job in progress, such as
scanning, faxing, or printing.
15. {#}} key
Press to enter after a numerical value.
22
17. {Start Manual RX}} key, {On Hook Dial}
} key, { Pause/Redial}
} key, and
{Tone}
} key
Reference
Facsimile Reference <Basic Features>
and Facsimile Reference <Advanced
Features>
18. Function keys
Press to select one of the following functions:
• Copy:
• Document Server:
• Facsimile:
• Printer:
• Scanner:
19. Function status indicators.
These show the status of the above functions:
• Yellow: selected.
• Green: active.
• Red: interrupted.
RussianC3_ENgsg-F_FM.book Page 23 Monday, June 16, 2003 6:48 PM
Control Panel
Display Panel
The display panel shows machine status, error messages, and function menus.
1
Important
❒ A force or impact of more than 30 N (about 3 kgf) will damage the display
panel.
The copying screen is displayed as default after power on.
The following display shows a machine with options fully installed.
The function items displayed serve as selector keys. You can select or specify an
item by lightly pressing them.
When you select or specify an item on the display panel, it is highlighted thus
. Keys appearing as
cannot be used.
Common key operations
The following keys are common to all screens:
❖ Key list
[OK]
Acknowledges a selected function or entered values, and then returns
to the previous display.
[Cancel]
Deletes a selected function or entered values, and then returns to the
previous display.
[U
UPrev.] [T
TNext]
Moves to the previous or next display when all items cannot be shown
on the same display.
[OK] [Yes]
Closes displayed messages.
[Clear]
Cancels entered values but does not change the settings.
[Exit]
Returns to the previous display.
23
RussianC3_ENgsg-F_FM.book Page 24 Monday, June 16, 2003 6:48 PM
Getting Started
Turning On the Power
This machine has two power switches.
1
❖ Operation switch (right side of the
control panel)
Press to activate the machine.
When the machine has finished
warming up, you can make copies.
❖ Main power switch (left side of the machine)
Turning off this switch makes the
main power indicator on the right
side of the control panel go off.
When this is done, machine power
is completely off.
When the fax unit (optional) is installed, fax files in memory may be
lost if you turn this switch off. Use
this switch only when necessary.
Important
❒ Do not turn off the main power
switch immediately after turning it on. Doing so may result in
damage to the hard disk or
memory, leading to malfunctions.
Turning On the Power
A Press the operation switch.
The On indicator goes on.
Note
❒ This machine automatically enters
Energy Saver mode or turns itself
off if you do not use it for a while.
See p.58 “Auto Off Timer”.
Turning On the Main Power
A Make sure that the power cord is
firmly plugged into the wall outlet.
B Open the switch cover, and then
turn on the main power switch.
The main power indicator goes on.
ZFFH250E
24
Note
❒ If the power does not come on
when the operation switch is
pressed, check the main power
switch is on. If it is off, turn it on.
RussianC3_ENgsg-F_FM.book Page 25 Monday, June 16, 2003 6:48 PM
Turning On the Power
Turning Off the Power
A Make sure the On indicator is not
A Make sure the exposure glass cov-
B Open the switch cover, and then
er or the ADF is in the right position.
B Press the operation switch.
lit.
1
turn off the main power switch.
The main power indicator goes
out.
The On indicator goes out.
-When the fax unit (optional) is
installed
When the main power switch is
turned off while using the facsimile
function, waiting fax and print jobs
may be canceled, and incoming fax
documents not received. If you have
to turn off this switch for some reason, follow the procedure below.
Note
❒ Even if you press the operation
switch, the indicator does not
go out, the blinks in the following cases:
• When the exposure glass
cover or ADF is open.
• During communication with
external equipment.
• When the hard disk is active.
Turning Off the Main Power
Important
❒ Do not turn off the main power
switch when the On indicator is lit
or blinking. Doing so may result in
damage to the hard disk or memory.
❒ Be sure to turn off the main power
switch before pulling out the power plug. Not doing this may result
in damage to the hard disk or
memory.
Important
❒ Make sure 100% is shown as available memory on the display before
turning off the main power switch
or unplugging the power cord. Fax
files in memory are deleted an
hour after you turn off the main
power switch or unplug the power
cord. See ”Power Failure Report”,
Facsimile Reference <Advanced Features>.
❒ The On indicator does not go out,
but blinks in dial-in mode even if
you press the operation switch.
When this happens, check the explanations below, and turn off the
main power switch.
• The computer is not controlling
the machine.
• The machine is not receiving a
fax.
25
RussianC3_ENgsg-F_FM.book Page 26 Monday, June 16, 2003 6:48 PM
Getting Started
Saving Energy
1
- Energy Saver Mode
If you do not use the machine for a
certain period after an operation, or
when you press the { Energy Saver}
}
key, the display disappears and the
machine goes into Energy Saver
mode. When you press the {Energy
Saver}
} key again, the machine returns
to the ready condition. The machine
uses less electricity in Energy Saver
mode.
Note
❒ You can change the amount of time
the machine waits before switching to Energy Saver mode after
copying has finished or the last operation is performed. See p.58
“Panel Off Timer”.
26
-Auto Off
The machine automatically turns itself off when the job is finished, after
a certain period of time has elapsed.
This function is called "Auto Off".
Note
❒ You can change the Auto Off time.
See p.58 “Auto Off Timer”.
❒ The Auto Off Timer function will
not operate in the following cases:
• When a warning message appears
• When the service call message
appears
• When paper is jammed
• When the cover is open
• When the "Add Toner" message
appears
• When toner is being replenished
• When the User Tools/Counter
screen is displayed
• When fixed warm-up is in
progress
• When the facsimile, printer, or
other functions are active
• When operations were suspended during printing
• When the handset is in use
• When the On-hook dialing
function is in use
• When a recipient is being registered in the address list or
group dial list
• When the Data In indicator is on
or blinking
• When the sample print or
locked print screen is displayed
RussianC3_ENgsg-F_FM.book Page 27 Monday, June 16, 2003 6:48 PM
2. Combined Function
Operations
Changing Modes
Note
❒ You cannot switch modes in any of the following situations:
• When scanning in a fax message for transmission
• During immediate transmission
• When accessing User Tools
• During interrupt copying
• During On hook dialing for fax transmission
• While scanning an original
27
RussianC3_ENgsg-F_FM.book Page 28 Monday, June 16, 2003 6:48 PM
Combined Function Operations
❒ The copying screen is displayed as default after power on. You can change
this default setting. See p.51 “Function Priority”.
2
ZLFS290N
- System Reset
The machine returns automatically to its initial condition when the job is finished, after a certain period of time has elapsed. This function is called "System
Reset".
Note
❒ You can change the System Reset time. See p.58 “System Auto Reset Timer”.
28
RussianC3_ENgsg-F_FM.book Page 29 Monday, June 16, 2003 6:48 PM
Multi-Access
Multi-Access
You can carry out another job using a different function while the current job is
being performed. Performing multiple functions simultaneously like this is
called "Multi-accessing".
This allows you to handle jobs efficiently, regardless of how the machine is being
used. For example:
• While making copies, you can scan documents to store in the Document Server.
• While printing documents stored in the Document Server, the machine can
receive print data.
• You can make copies while receiving fax data.
• While printing print data, you can make operations for copying.
2
Note
❒ See p.52 “Print Priority” for setting function priority. As default, [Display
mode] is set to first priority.
❒ When the Internal Tray 2 (1 bin tray), Shift Sort Tray, 500–sheet finisher, or
1000–sheet finisher is installed on the machine, you can specify the output
tray where documents are delivered. For details about how to specify the output tray for each function, see the following descriptions:
• p.53 “Output: Copier (copier)”
• p.53 “Output: Document Server (Document Server)”
• p.53 “Output: Facsimile (facsimile)”
• p.53 “Output: Printer (printer)”
- Function Compatibility
The chart shows Function Compatibility when print priority is set to "Interleave". See p.52 “Print Priority”.
|: Simultaneous operations are possible.
$: Operation is enabled when the relevant function key is pressed and remote
switching (of the scanner) is done.
❍: Operation is enabled when the {Interrupt}
} key is pressed to interrupt the preceding operation.
→: Operation is performed automatically once the preceding operation ends.
×: The operation must be started once the preceding operation ends. (Simultaneous operations are not possible.)
29
RussianC3_ENgsg-F_FM.book Page 30 Monday, June 16, 2003 6:48 PM
× × × ❍ ❍ $ $| $| | | | | $$$ $$| | |
| → → ❍ ❍ $ $| $| | | | → $ $$ $→ | | |
*1 *1 *1
Sort
*5
*2
*2
*2
*2
*4
*4
| → → ❍ ❍ $ $| $| | | | | $ $$ $→ | | |
*1 *1 *1
*2
*2
*2
❍ ❍ × × × × | × | | | | | × × × × × | | |
Facsimile
❍ ❍ × × × × | × | → | → → × × × × × → | →
$$❍ ❍ × × | × | | | | | $$$ $$| | |
Reception
Transmission
Operations for
❍
Copying
Copying
❍
Transmission
$
Operation/Manual
Reception Operation
Scanning an orig- ×
inal for Memory
Transmission
Memory
|
Transmission
*2
Interrupt Copying
Scanner
× × × × × × | × | | | | | × × × × × | | |
| | | | | | | | | | | | | | | | | | | →|
*3 *3 *3 *7
*3
Immediate
Transmission
× × × × × × × | × | | | | | × × × × × | →|
Memory
Reception
| | | | | | | | | | | | | | | | | | | | →|
Printing
Received Data
| | | | | | | | | | × | | | | | | | | | →|
Data Reception
Sort Print
Stapling
Print
Printer
30
Printing
Mode before you select
Copy
Operations for
Copying
Stapling
Printer
Scanning
Document Server
Operations for Document Server
Scanning a Document to Store in Document Server
Printing from Document Server
DeskTopBinder V2
Printing from Document Server
Professional/Lite
Sending a Facsimile from Document Server
2
Facsimile
Operations for Copying
Stapling
Sort
Interrupt Copying
Operations for Copying
Copying
Transmission Operation/Manual Reception Operation
Scanning an Original for Memory Transmission
Transmission
Memory Transmission
Immediate Transmission
Memory Reception
Reception
Printing Received Data
Data Reception
Printing
Print
Stapling
Scanner
Operations for Scanning
Mode after you select Copy
Web-Document Server
Combined Function Operations
*3
*3
*3 *3 *3 *7
*7
*3
*7
*3
| | | | | | | | | | | → → → | | | | | | | |
| | | ❍ ❍ | | | | | | | → → | | | | | | | |
| → | ❍ ❍ | | | | | | | → → | | | | | | | |
*5
Operations for
scanning
Scanning
*3
*4 *4
*4
$$$ ❍ ❍ $ $| $| | | | | × × $ $$ | | |
× × × × × × × | × | | | | | × × × × × | | |
RussianC3_ENgsg-F_FM.book Page 31 Monday, June 16, 2003 6:48 PM
Mode before you select
$$$ ❍ ❍ $ $| $| | | | | $$×
Document Server
Operations for
Document Server
Scanning a Docu- $ × × ❍ ❍ $ × | × | | | | | $ × ×
ment to Store in
Document Server
Printing from
$→ → ❍ ❍ | | | | | | | | | | | |
Document Server
*6
DeskTopBinder V2
Professional/Lite
WebDocument
Server
*1
*2
*3
*4
*5
*6
*7
2
Printing
Printer
Scanning
Document Server
Operations for Document Server
Scanning a Document to Store in Document Server
Printing from Document Server
DeskTopBinder V2
Printing from Document Server
Professional/Lite
Sending a Facsimile from Document Server
Facsimile
Operations for Copying
Stapling
Sort
Interrupt Copying
Operations for Copying
Copying
Transmission Operation/Manual Reception Operation
Scanning an Original for Memory Transmission
Transmission
Memory Transmission
Immediate Transmission
Memory Reception
Reception
Printing Received Data
Data Reception
Printing
Print
Stapling
Scanner
Operations for Scanning
Mode after you select Copy
Web-Document Server
Multi-Access
× × | | |
× × | | |
| | | | |
*6 *6
Printing from
| | | | | | | | | | | | | | | | | | | → | |
Document Server
*4
| | | | | | | | | | | | | | | | | | | | → |
Sending a
Facsimile from
*3 *3 *3 *3
Document Server
Printing
| | | | | | | | | | | | | | | | | | | | | →
*4
Simultaneous operations are only possible after the preceding job documents are all
scanned and the [Next Job] key appears.
You can scan a document after the preceding job documents are all scanned.
When multiple lines are available, select a line which is currently not in use. Otherwise, operation will not be possible.
During stapling, printing automatically starts after the current job.
Stapling is not available.
Simultaneous operations become possible after you press the [Next Job] key.
During parallel receptions, any subsequent job is suspended until the receptions are
completed.
Limitation
❒ Stapling cannot be used at the same time for multiple functions.
31
RussianC3_ENgsg-F_FM.book Page 32 Monday, June 16, 2003 6:48 PM
Combined Function Operations
Note
❒ A machine with the 500–sheet finisher installed cannot accept other jobs
while printing with the stapling operation.
❒ A machine with the 1000–sheet finisher installed, that is printing with the stapling operation on paper larger than A4 size, starts the subsequent job (for
which Shift Sort Tray is specified as the output tray) only after the current
print job finishes.
❒ While printing is in progress, scanning using another function may take more
time.
2
32
RussianC3_ENgsg-F_FM.book Page 33 Monday, June 16, 2003 6:48 PM
3. Document Server
Relationship between Document Server
and Other Functions
The following table describes the relationship between the Document Server
and other functions.
function
Where to store
documents
Displaying a list
Printing stored
documents
Sending
documents
Copy
Copy/Document
Server
Available
Available
Not Available
Printer
Document Server
Available
Available
Not Available
Facsimile
Facsimile
Available
Available
Available *1
Scanner
Scanner
Not Available *2
Not Available
Available *3
*1
*2
*3
You can send stored documents using the facsimile function. See “Sending a Stored
File”, Facsimile Reference <Advanced Features>.
You can display stored documents using the scanner function. See Scanner Reference .
You can send stored documents using the scanner function. See Scanner Reference.
Note
❒ The following table shows the capacity of the Document Server.
Number of pages for
each file
Number of files
Number of pages in
total
1,000 pages
3,000 files
9,000 pages
Copy
Printer
Scanner
Facsimile
33
RussianC3_ENgsg-F_FM.book Page 34 Monday, June 16, 2003 6:48 PM
Document Server
Document Server Display
❖ Document Server Main Display
3
ZLFS300N
1. Operating status and messages.
2. The title of the currently selected
4. The operation keys.
5. The functions under which the
screen.
documents were stored.
3. The numbers of originals, copies,
and printed pages.
The icons below show the functions active when the documents were stored
in the Document Server.
Function
Icon
34
Copier
Facsimile
Printer
Scanner
--
RussianC3_ENgsg-F_FM.book Page 35 Monday, June 16, 2003 6:48 PM
Using the Document Server
Using the Document Server
Storing Data
❖ File name
Stored documents are automatically
named "COPY0001", "COPY0002".
You can change assigned file
names.
❖ User name
You can register a user name to
identify the user or user group that
stored the documents. To assign it,
you can register the user name using the name assigned to the user
code, or by entering the name directly.
Note
❒ Data stored in the Document Server is set to be deleted after three
days (72 hours) by default. You can
specify the period after which
stored data is automatically deleted. See p.65 “Auto Delete File”.
❒ If you do not want stored data to
be automatically deleted, select
[No] in Auto Delete File before storing a document. If you select [Yes]
later, data stored after will be automatically deleted.
3
A Press the {Document Server}} key.
Reference
For details about user codes, see
p.70 “User Codes”.
❖ Password
You can set a password for stored
documents, and use it to prevent
others printing them. When a password is set for the documents,
appears next to the documents.
ZLFH360N
B Press [Scan Original].
Reference
To store documents without using
Document Server function, see the
manuals for those modes.
Important
❒ Data stored in the machine might
be lost if some kind of failure occurs. The manufacture shall not be
responsible for any damage resulting from loss of data.
35
RussianC3_ENgsg-F_FM.book Page 36 Monday, June 16, 2003 6:48 PM
Document Server
C Enter a user name, file name, or
password if necessary.
Note
❒ If you do not enter a file name,
one is automatically assigned.
Reference
p.36 “To register or change a
user name”
p.37 “To change a file name”
p.37 “To set or change a password”
3
❒ If you placed originals on the
exposure glass, press [Scanning
Finished] after all the originals
have been scanned. The Select
Files to Print display appears.
To register or change a user name
A Press [Scan Original].
The scan original display appears.
B Press [User Name].
D Place originals either on the exposure glass or in the ADF.
Reference
For information about types of
originals and how to place
them, see Copy Reference.
E Make any required settings.
Reference
For details, see Copy Reference.
F Press the {Start}} key.
The document is stored in the Document Server.
Note
❒ To stop scanning, press the
{ Clear/Stop}
} key. To restart a
paused scanning job, press [Continue] in the confirmation display. To delete saved images
and cancel the job, press the
[Stop] key.
❒ When a password is set,
appears on the left side of the file
name.
36
If user names are already registered,
the Change User Name display appears. To use an unregistered user
name, press [Non-programed Name].
When no user name are registered
in the Address Book, the User
(Destination) Name entry display
appears.
Reference
p.70 “User Codes”
When using a registered user
name in the Address Book
A Select a registered user name
from the list, and then press [OK].
To change your user name to an
unregistered user name, proceed to the next step.
Reference
p.70 “Registering a New
User Code”
RussianC3_ENgsg-F_FM.book Page 37 Monday, June 16, 2003 6:48 PM
Using the Document Server
When using an unregistered user
name in the Address Book
A To enter an unregistered user
name, press [Non-programed
Name].
B Enter a new user name, and
then press [OK].
Reference
p.143 “Entering Text”
When no user name has been
registered in the Address Book
A Enter a new user name, and
then press [OK].
D Enter a new file name, and then
press [OK].
Note
❒ Up to 20 characters can be entered as a file name. Note that
only 16 characters of each file
name appear in the document
list.
Reference
p.143 “Entering Text”
3
To set or change a password
A Press [Scan Original].
The Scan Original display appears.
B Press [Password].
Reference
p.143 “Entering Text”
To change a file name
A Press [Scan Original].
The Scan Original display appears.
B Press [File Name].
C Enter a password using the number keys (four digits), and then
press the {#}
} key.
D Reenter the password (four digits) for verification, and then
press the {#}
} key.
E Press [OK].
The Change File Name display appears.
C Press [Delete All] to delete the old
file name.
Note
❒ You can also use [Backspace] to
delete unnecessary characters.
37
RussianC3_ENgsg-F_FM.book Page 38 Monday, June 16, 2003 6:48 PM
Document Server
Changing a Stored
Document's File Name, User
Name, or Password
A Press the {Document Server}} key.
B Select the document with the user
Selecting a Document
A Press the {Document Server}} key.
B Select a document you want to
print.
name, file name, or password you
want to change.
3
Note
❒ If a password is already set for
the document, enter that password, and then press [OK].
C Press [File Management].
D Press [Change User Name], [Change
File Name], or [Change Password].
E Enter
the new user name, file
name, or password using the letter keys or number keys, and then
press [OK].
Reference
p.36 “To register or change a
user name”
p.37 “To change a file name”
p.37 “To set or change a password”
F Press [OK].
38
Note
❒ If a password is already set for
the document, enter that password, and then press [OK].
❒ You can search for the document using [Search by User Name]
or [Search by File Name] at the left
top of the display. See p.39
“Searching for Stored Documents”.
❒ You can sort document names
in the list by user name, file
name, or date. To sort documents, press [User Name], [File
Name], or [Date].
❒ If you cannot determine docum ent c on te nt from t he file
name, you can print just the first
page of the document for checking purposes. See p.42 “Printing
first page”.
❒ To cancel document selection,
press it again.
RussianC3_ENgsg-F_FM.book Page 39 Monday, June 16, 2003 6:48 PM
Using the Document Server
C To print multiple documents, repeat step B in the order you want
to print.
Note
❒ You can select up to 30 documents.
❒ If the sizes or resolution of selected documents are not the
same, it may not be possible to
print them.
❒ If you want to change the printing order, cancel the selection,
and select documents again,
this time in the order you want.
❒ If you press the {Clear Modes}
}
key, selection of all documents
will be canceled.
❒ If you press [Printg Odr], the documents in print order.
To check the details of stored documents
A Select a document to display its
detailed information.
Note
❒ If you selected several documents, use [U
U] and [T
T] to view
the details of each.
❒ Press [OK]. The Select Files to
Print display reappears.
Searching for Stored
Documents
3
You can use either [Search by File
Name] or [Search by User Name] to
search for documents stored in the
Document Server. You can also list
stored documents in a preferred order.
Note
❒ If you install DeskTopBinder V2
Professional or DeskTopBinder V2
Lite on your computer, you can
search for and rearrange documents using your computer.
Reference
Manuals for DeskTopBinder V2
Professional/Lite or Help
To search by file name
Note
❒ If a password is already set for
the document, enter that password, and then press [OK].
A Press the {Document Server}} key.
B Press [Search by File Name].
B Press [Detail].
Detailed information about the
document appears.
39
RussianC3_ENgsg-F_FM.book Page 40 Monday, June 16, 2003 6:48 PM
Document Server
C Enter the file name using the letter keys, and then press [OK].
Only files beginning with the
name entered appear in the Select
Files to Print display.
Reference
p.143 “Entering Text”.
Note
❒ To display all files stored in the
Document Server, press [File
List].
3
To search by user name
A Press the {Document Server}} key.
B Press [Search by User Name].
E Press [OK].
Only files beginning with the
name entered appear in the Select
Files to Print display.
Note
❒ To display all files stored in the
Document Server, press [File
List].
Printing Stored Documents
Note
❒ You can print stored documents
from a network computer using a
Web browser. For details about
how to start the Web browser, see
Network Guide.
A Select
a document you want to
print.
C To specify a registered user name,
select the user name from the displayed list, and then press [OK].
Note
❒ To specify an unregistered user
name, follow the procedure below.
D To
specify an unregistered user
name, press [Non-programed Name].
Enter a user name, and then press
[OK].
Reference
p.143 “Entering Text”
40
Note
❒ If a password is already set for
the document, enter that password, and then press [OK].
❒ You can print multiple documents. See p.38 “Selecting a
Document”.
B If you need to change print settings, press [Print Settings].
The Print Settings display appears.
User names, file names, and print
order of documents appear.
RussianC3_ENgsg-F_FM.book Page 41 Monday, June 16, 2003 6:48 PM
Using the Document Server
Note
❒ Print settings made for printing
in copier or printer function remain after printing and applied
to the next job. Print settings
made in facsimile mode, however, do not remain.
❒ If you select multiple documents, print settings remain applied to the first document, but
not to other documents.
❒ Print setting items are listed below. For details about print results of each setting, see Copy
Reference.
❖ Binding format
• 2 Sided Copy Top to Top
• 2 Sided Copy Top to Bottom
• Booklet
• Magazine
❖ Cover handling
• Cover/Slip sheet
• Edit/Stamp
❖ Finish
• Sort
• Stack
• Staple
❒ If you print more than one set
using the Sort function, you can
check the print result by printing out only the first set. See
p.42 “Sample copy”.
❒ When multiple documents are
printed at the same time, you
can combine them into a single
set by adjusting the print order.
❒ When multiple documents are
printed at the same time, print
settings made for the document
printed first are applied to all
other documents.
❒ If you select multiple files, you
can check file names or print order selected in step A by scrolling the list using [T
T] and [U
U].
❒ Press [Select File] to return to the
Select Files to Print display.
❒ "Booklet", "Magazine", and
"Stamp" cannot be set for documents saved in facsimile mode.
❒ "Booklet" and "Magazine" cannot be set for documents saved
under multiple functions.
3
C Enter
the required number of
prints using the number keys.
Note
❒ Up to 99 can be entered.
D Press the {Start}} key.
Printing starts.
To stop printing
A Press the {Clear/Stop}} key.
B Press [Stop].
41
RussianC3_ENgsg-F_FM.book Page 42 Monday, June 16, 2003 6:48 PM
Document Server
Changing the number of copies
during printing
Limitation
❒ The number of copies can only be
changed when the Sort function is
selected in the print settings.
A Press the {Clear/Stop}} key.
B Press [Change Quantity].
C Enter a new number of copies us-
3
ing the number key.
D Press the {#}} key.
E Press [Continue].
❒ You can sort document names
in the list by user name, file
name, or date. To sort documents, press [User Name], [File
Name], or [Date].
❒ To cancel a document selection,
press it again.
B Press the {Sample Copy}} key.
The first set prints out.
C If the sample is acceptable, press
[Print].
Note
❒ Press [Suspend] to cancel printing and return to the Print Settings menu to change settings.
Printing restarts.
Printing first page
Sample copy
If you print multiple sets using the
Sort function, you can check the print
order or print settings are correct by
printing only the first set using the
{Sample Copy}
} key.
Limitation
❒ This function can only be used
when the Sort function is selected.
A Select the document.
42
Note
❒ If a password is already set for
the document, enter that password, and then press [OK].
❒ You can search for the document by using [Search by User
Name] or [Search by File Name] at
the left top of the display. See
p.39 “Searching for Stored Documents”.
You can print the first page of the document selected in the Select Files to
Print display to check its content.
If more than one document selected,
the first page of each is printed.
A Select the document.
Note
❒ If a password is already set for
the document, enter that password, and then press [OK].
❒ You can search for the document by using [Search by User
Name] or [Search by File Name] at
the left top of the display. See
p.39 “Searching for Stored Documents”.
❒ You can sort document names
in the list by user name, file
name, or date. To sort documents, press [User Name], [File
Name], or [Date].
❒ To cancel a document selection,
press it again.
RussianC3_ENgsg-F_FM.book Page 43 Monday, June 16, 2003 6:48 PM
Using the Document Server
B Press [Print 1st Page].
C Press the {Start}} key.
Deleting Stored Documents
Important
❒ You can store up to 3,000 documents in the Document Server. No
more documents can be stored
when the total is 3,000. You should
delete unnecessary documents to
increase available memory.
Note
❒ You can delete all stored documents at once with User Tools. See
p.66 “Delete All Files”.
❒ You can delete stored documents
from a network computer using
the Web browser. For details about
how to start the Web browser, see
Network Guide.
❒ You can sort document names
in the list by the user name, file
name, or date. To sort documents, press [User Name], [File
Name], or [Date].
❒ If you cannot find the document
by name, you can print the first
page of a document to check its
contents. See p.42 “Printing first
page”.
❒ Press the selected line again to
cancel the print job.
3
C Press [Delete File].
D Press [Delete] to delete the document.
A Press the {Document Server}} key.
B Select the document to delete.
Note
❒ If a password is already set for
the document, enter that password, and then press [OK].
❒ You can delete multiple documents at once. See p.38 “Selecting a Document”.
❒ You can search for a document
by using [Search by User Name] or
[Search by File Name] at the left
top of the display. See p.39
“Searching for Stored Documents”.
43
RussianC3_ENgsg-F_FM.book Page 44 Monday, June 16, 2003 6:48 PM
Document Server
Viewing Stored Documents
Using a Web Browser
Reference
The Web browser's Help
A Start a Web browser.
B Enter “http:// (IP address of this
machine) /” in the [Address] box.
The top page appears on the Web
browser.
3
C Click [Document Server].
The [Document Server File List] appears.
Note
❒ To switch the display format,
click [Details], [Thumbnails] or
[Icons] from the [Display method]
list.
D Click the properties button of the
document you want to check.
Information about that document
appears.
E Check the document's content.
Note
❒ To enlarge the document preview, click [Enlarge Image].
Downloading Stored
Documents
Note
❒ File Format Converter is required
when downloading documents
stored in copier or printer mode.
A Start a Web browser.
B Enter “http:// (IP address of this
machine) /” in the [Address] box.
The top page appears on the Web
browser.
C Click [Document Server].
The [Document Server File List] appears.
Note
❒ To switch the display format,
click [Details], [Thumbnails] or
[Icons] from the [Display method]
list.
D Click the properties button of the
document you want to download.
E Select [PDF], [JPEG], or [Multi-page
TIFF] in the [File format] list.
Note
❒ [JPEG] can only be selected for
documents stored in scanner
mode.
❒ [Multi-page TIFF] is available
when file Format Converter is
installed.
F Click [Download].
G Click [OK].
44
RussianC3_ENgsg-F_FM.book Page 45 Monday, June 16, 2003 6:48 PM
Settings for the Document Server
Settings for the Document Server
❖ Copier/Document Server Features (See "General Features 4/4", Copy Reference.)
Items
General Features
Default
Document Server Storage
Key: F1
2 Sided Original Top to top
Document Server Storage
Key: F2
1 Sided→1 Sided Combine
Document Server Storage
Key: F3
1 Sided→1 Sided Combine:
4 originals
Document Server Storage
Key: F4
1 Sided→1 Sided Combine:
8 originals
Document Server Storage
Key: F5
Create Margin
3
❖ System Settings (See p.51 “General Features”, p.55 “Tray Paper Settings”, p.58
“Timer Settings”, and p.59 “Key Operator Tools”.)
General Features
Tray Paper Settings
Timer Settings
Key Operator Tools
Items
Default
Warm Up Notice
ON
Copy Count Display
Up
Output: Document Server
Internal tray 1
Paper Tray Priority: Copier
Tray 1
Cover Sheet Tray
Off
Slip Sheet Tray
Off
Copier/Document Server
Auto Reset Timer
60 seconds
Auto Delete File
Yes After 3 day(s)
Delete All Files
--
Password Management for
Stored Files
Do not Unlock
45
RussianC3_ENgsg-F_FM.book Page 46 Monday, June 16, 2003 6:48 PM
Document Server
3
46
RussianC3_ENgsg-F_FM.book Page 47 Monday, June 16, 2003 6:48 PM
4. User Tools (System Settings)
User Tools Menu (System Settings)
Reference
For details about Interface Settings and File Transfer, see “User Tools Menu
(System Settings)”, Network Guide.
For details about parallel interface, see “System Settings (Parallel Connection)”, Printer Reference 2.
❖ General Features (See p.51 “General Features”.)
Default
Panel Tone
ON
Warm Up Notice
ON
Copy Count Display
Up
Function Priority
Copier
Print Priority
Display mode
Function Reset Timer
Set Time
Output: Copier
Internal tray 1
Output: Document Server
Internal tray 1
Output: Facsimile
Internal tray 2
Output: Printer
Internal tray 1
<F/F4> Size Setting
81/2" × 13"L
47
RussianC3_ENgsg-F_FM.book Page 48 Monday, June 16, 2003 6:48 PM
User Tools (System Settings)
❖ Tray Paper Settings (See p.55 “Tray Paper Settings”.)
Default
4
Paper Tray Priority: Copier
Tray 1
Paper Tray Priority: Facsimile
Tray 1
Paper Tray Priority: Printer
Tray 1
Tray Paper Size: Tray 1
A4K, 81/2" × 11" K
Tray Paper Size: Tray 2
A3L, 11" × 17" L
Tray Paper Size: Tray 3
A4L, 81/2" × 11" L
Tray Paper Size: Tray 4
A4L, 81/2" × 14" L
Paper Type: Bypass tray
No display
Paper Type: Tray 1
No display/2 Sided Copy/Auto Paper Select on
Paper Type: Tray 2
No display/2 Sided Copy/Auto Paper Select on
Paper Type: Tray 3
No display/2 Sided Copy/Auto Paper Select on
Paper Type: Tray 4
No display/2 Sided Copy/Auto Paper Select on
Cover Sheet Tray
Off
Slip Sheet Tray
Off
❖ Timer Settings (See p.58 “Timer Settings”.)
Default
Auto Off Timer
1 minute(s)
Panel Off Timer
1 minute(s)
System Auto Reset Timer
60 seconds
Copier/Document Server Auto Reset Timer 60 seconds
Facsimile Auto Reset Timer
30 seconds
Scanner Auto Reset Timer
60 seconds
Set Date
--
Set Time
--
❖ Interface Settings
• For details about network settings, see “User Tools Menu (System Settings)”, Network Guide.
• For details about parallel interface, see “System Settings (Parallel Collection)”, Printer Reference 2.
❖ File Transfer
• For details about network settings, see “User Tools Menu (System Settings)”, Network Guide.
48
RussianC3_ENgsg-F_FM.book Page 49 Monday, June 16, 2003 6:48 PM
User Tools Menu (System Settings)
❖ Key Operator Tools (See p.59 “Key Operator Tools”.)
Default
User Code Management
Copier
OFF
Document Server
OFF
Facsimile
OFF
Scanner
OFF
Printer
Auto Program
Key Counter Management
All OFF
External Charge Unit Management
--
Key Operator Code
OFF
Extended Security
OFF
Display/Print Counter
--
Display/Clear/Print Counter per User Code
--
Print Address Book: Destination List
--
Address Book Management
--
Address Book: Program/Change/Delete Group
--
Address Book: Program/Change/Delete Transfer Request
--
Address Book: Change Order
--
Address Book: Edit Title
--
Address Book: Select Title
Title 1
Auto Delete File
After 3 day(s)
Delete All Files
--
Password Management for Stored Files
Do not Unlock
AOF (Always ON)
ON
Program/Change LDAP Server
--
Use LDAP Server
OFF
4
49
RussianC3_ENgsg-F_FM.book Page 50 Monday, June 16, 2003 6:48 PM
User Tools (System Settings)
Accessing User Tools (System Settings)
This section is for key operators in
charge of this machine.
User Tools allow you to change or set
defaults.
Note
❒ Operations for system settings differ from normal operations. Always quit User Tools when you
have finished. See p.50 “Exiting
User Tools”.
❒ Any changes you make with User
Tools remain in effect even if the
main power switch or operation
switch is turned off, or the {Energy
Saver}
} or { Clear Modes}
} key is
pressed.
4
C Select the menu, and then press
the appropriate key.
Reference
p.47 “User Tools Menu (System
Settings)”
D Change settings by following instructions on the display panel,
and then press [OK].
Note
❒ To cancel changes made to settings and return to the initial
display, press the {User
Tools/Counter}
} key.
Exiting User Tools
Changing Default Settings
A Press the {User Tools/Counter}} key.
Note
❒ If a key operator code is already
set, the key operator code entry
display appears. Enter the key operator code, and then press [OK].
See p.60 “Key Operator Code”.
A Press the {User Tools/Counter}} key.
Note
❒ You can also exit User Tools by
pressing [Exit].
B Press [System Settings].
50
RussianC3_ENgsg-F_FM.book Page 51 Monday, June 16, 2003 6:48 PM
Settings You Can Change with User Tools
Settings You Can Change with User Tools
Reference
To access User Tools, see p.50 “Accessing User Tools (System Settings)”.
General Features
❖ Panel Tone
The beeper (key tone) sounds when a key is pressed.
Note
❒ Default: ON
4
❖ Warm Up Notice (copier/Document Server)
You can have the beeper sound when the machine becomes ready to copy after leaving Energy Saver mode, or when the power is turned on.
Note
❒ If the Panel Tone setting is “OFF”, the beeper does not sound, whatever the
Warm Up Notice setting.
❒ Default: ON
❖ Copy Count Display (copier/Document Server)
The copy counter can be set to show the number of copies made (count up) or
the number of copies yet to be made (count down).
Note
❒ Default: Up (count up)
❖ Function Priority
You can specify the mode to be displayed immediately after the operation
switch is turned on, or when System Reset mode is turned on.
Note
❒ Default: Copier
51
RussianC3_ENgsg-F_FM.book Page 52 Monday, June 16, 2003 6:48 PM
User Tools (System Settings)
❖ Print Priority
Print Priority is given to the mode selected.
Reference
p.29 “Multi-Access”
Note
❒ Default: Display mode
❒ When [Interleave] is selected, the current print job will be interrupted after
a maximum of five sheets.
❒ When the Internal Tray 2 (1 bin tray), Shift Sort Tray, 500–sheet finisher, or
1000–sheet finisher is installed on the machine, you can specify an output
tray for each documents are delivered. For details about how to specify an
output tray for each function, see the following sections:
• p.53 “Output: Copier (copier)”
• p.53 “Output: Document Server (Document Server)”
• p.53 “Output: Facsimile (facsimile)”
• p.53 “Output: Printer (printer)”
4
❖ Function Reset Timer
You can set the length of time the machine waits before changing modes
when using the multi-access function (see p.29 “Multi-Access”). This is useful
if you are making many copies and have to change settings for each copy. If
you set a longer reset period, you can prevent interruption from other functions.
Note
❒ Default: Set Time
❒ The Function Reset Timer setting is ignored if [Interleave] is set for Print Priority (see p.52 “Print Priority”).
❒ When you select [Set Time], enter the time (3–30 seconds, in 1 second increments) using the number keys.
❒ The default time is three seconds.
52
RussianC3_ENgsg-F_FM.book Page 53 Monday, June 16, 2003 6:48 PM
Settings You Can Change with User Tools
❖ Output: Copier (copier)
You can specify a tray to which documents are delivered.
1
2
4
1
3
4
4
ZLFH150E
1. Internal Tray 1
2. Internal Tray 2
3. Finisher Upper Tray
4. Finisher Shift Tray
Note
❒ Default: Internal Tray 1
❖ Output: Document Server (Document Server)
You can specify a tray to which documents are delivered.
Note
❒ Default: Internal Tray 1
❒ For details about output trays, see p.53 “Output: Copier (copier)”.
❖ Output: Facsimile (facsimile)
You can specify a tray to which documents are delivered.
Note
❒ Default: Internal Tray 2
❒ For details about output trays, see p.53 “Output: Copier (copier)”.
❖ Output: Printer (printer)
You can specify a tray to which documents are delivered.
Note
❒ Default: Internal Tray 1
❒ The output trays set on the printer driver have priority over the output tray
specified above.
❒ For details about output trays, see p.53 “Output: Copier (copier)”.
53
RussianC3_ENgsg-F_FM.book Page 54 Monday, June 16, 2003 6:48 PM
User Tools (System Settings)
❖ <F/F4> Size Setting
Currently three types of F size are available; 81/2"×13"L, 81/4"×13"L and
8"×13"L. The ADF or exposure glass cover sensor cannot distinguish these
three types of originals. This function sets the F size from the ADF or exposure glass cover sensor. Auto Paper Select or Auto Reduce/Enlarge can be
used for F size originals based on this setting.
Note
❒ Default: 81/2"×13"L
Output tray settings
Limitation
❒ You cannot interrupt the current job with a different function job that specifies stapling or sorting.
❒ You can interrupt the current job with an ordinary copy job or facsimile reception. The output tray used when the job is interrupted varies depending
on the type of finisher shift tray and output tray specified for interruption.
4
❖ When 500–sheet finisher is the finisher shift tray:
• When the output tray specified for the interrupting job is the finisher
tray, the interrupting job will be delivered to internal tray 1.
• When the output tray specified for the interrupting job is not the finisher tray, the interrupting job will be delivered to the specified output
tray.
❖ When 1000–sheet finisher is the finisher shift tray:
• When the output tray specified for the interrupting job is the finisher
tray, the interrupting job will be delivered to the finisher upper tray.
• When the output tray specified for the interrupting job is not the finisher tray, the interrupting job will be delivered to the specified output
tray.
❒ When the 500–sheet finisher or 1000–sheet finisher is installed and stapling is
specified for a job, the job will be delivered to the finisher shift tray, regardless
of the output tray specified.
54
RussianC3_ENgsg-F_FM.book Page 55 Monday, June 16, 2003 6:48 PM
Settings You Can Change with User Tools
Tray Paper Settings
❖ Paper Tray Priority: Copier (copier/Document Server)
You can specify the tray to supply paper for output.
Note
❒ Default: Tray 1
❖ Paper Tray Priority: Facsimile (facsimile)
You can specify the tray to supply paper for output.
Note
❒ Default: Tray 1
4
❖ Paper Tray Priority: Printer (printer)
You can specify the tray to supply paper for output.
Note
❒ Default: Tray 1
❖ Tray Paper Size: Tray 1–4
Select the size of the paper loaded in the paper tray.
❖ The paper sizes you can set for trays 1, 3 and 4 are as follows:
• A3L, B4 JISL, A4K, A4L, B5 JISK, B5 JISL, A5L, 8KL, 16KK,
16KL
• 11"×17"L, 81/2"×14"L, 81/2"×11"K, 81/2"×11"L, 51/2"×81/2"L,
7 1 / 4 "×10 1 / 2 "L, 8"×13"L, 8 1 / 2 "×13"L, 8 1 / 4 "×13"L, 11"×14"L,
81/4"×14"L, 8"×101/2"L, 8"×101/2"K, custom size (140-297 mm (5.52"11.69") wide x 182-432 mm (7.17"-17.00") long)
❖ The paper sizes you can set for tray 2 are as follows:
• A3L, B4 JISL, A4K, A4L, B5 JISK, B5 JISL, A5L, B6 JISL, A6L,
PostcardL, 8KL, 16KK, 16KL
• 11"×17"L, 81/2"×14"L, 81/2"×11"K, 81/2"×11"L, 51/2"×81/2"L,
71/4"×101/2"L, 71/4"×101/2"K, 8"×13"L, 81/ 2"×13"L, 81/4"×13"L,
11"×14"L, 11"×15"L, 10"×14"L, 10"×15"L, 81/4"×14"L, 8"×101/2"L,
8"×101/2"K, 8"×10"L, 8"×10"K, C5L, C6L, DL EnvL, 41/8"×91/2"L,
37/8"×71/2"L, custom size (100-297 mm (3.97"-11.69") wide x 148-432
mm (5.83"-17.00") long)
Reference
p.122 “Changing the Paper Size”
Important
❒ If the specified paper size differs from the actual size of the paper loaded
in the paper tray, a misfeed might occur because the correct paper size was
not detected.
55
RussianC3_ENgsg-F_FM.book Page 56 Monday, June 16, 2003 6:48 PM
User Tools (System Settings)
Note
❒ The paper guide for the optional LCT is fixed for A4K, 81/2"×11"K size paper. Contact your service representative if you need to change the paper size.
❒ If the paper size set for the selector in paper tray is different to the paper
size for this setting, the paper size of the dial has priority.
❒ If you load paper of a size not indicated on the paper size selector in the
paper tray, set the dial to " ".
❒ Default:
• Tray 1: A4K, 81/2" × 11"K
• Tray 2: A3L, 11" × 17"L
• Tray 3: A4L, 81/2" × 11"L
• Tray 4: A4L, 81/2" × 14"L
4
Reference
p.122 “Changing the Paper Size”
❖ Paper Type: Bypass tray
Sets the display so you can see what type of paper is loaded in the bypass tray.
❖ The paper types you can set for the bypass tray are as follows:
• No Display, Recycled Paper, Special Paper, Color Paper, Letterhead,
Preprinted Paper, Label Paper, Bond Paper, Thick Paper, OHP, Thin Paper, Cardstock
Note
❒ Default: No display
❖ Paper Type: Tray 1–4
Sets the display so you can see what type of paper is loaded in each paper
tray. The print function uses this information to automatically select the paper tray.
❖ The paper types you can set for trays 1, 3 and 4 are as follows:
• No Display, Recycled Paper, Special Paper, Color Paper, Letterhead,
Preprinted Paper, Bond Paper, Cardstock
❖ The paper types you can set for tray 2 are as follows:
• No Display, Recycled Paper, Special Paper, Color Paper, Letterhead,
Preprinted Paper, Label Paper, Bond Paper, Thick Paper, OHP, Thin Paper, Cardstock
56
Note
❒ Default:
• Paper Type: No Display
• Copying Method in Duplex: 2 Sided Copy
• Apply Auto Paper Select: Yes
RussianC3_ENgsg-F_FM.book Page 57 Monday, June 16, 2003 6:48 PM
Settings You Can Change with User Tools
❒ When paper of the same type and size is loaded in two different paper
trays and you want to specify tray for 2 Sided Copy and tray for 1 Sided
Copy, specify the upper tray for 2 Sided Copy. If one of the trays is specified as the default in Paper Tray Priority, assign 2 Sided Copy to that tray.
❒ A appears next to the paper tray if [No] is selected in Auto Paper Select.
Limitation
❒ [Auto Paper Select] can only be selected for the copier function if [No display]
and [Recycled paper] are selected. If [No] is selected, Auto Paper Select is not
valid for the tray.
❖ Cover Sheet Tray
Allows you to specify and display the paper tray that is setting cover sheets.
After selecting the paper tray, you can also specify the display timing and
copy method for two-sided copying.
4
Note
❒ Default:
• Tray to Program: Off
❒ Functions using the cover sheet tray setting are the front cover function
and front/back cover function.
❒ When [At Mode Selected] is selected, cover sheet tray settings only appear
when the cover function or slip sheet function is selected.
❒ When [Full Time] is selected, the cover sheet tray is always displayed.
❒ You can set Copying Method in Duplex only when [At Mode Selected] is selected.
Reference
“Covers”, Copy Reference
❖ Slip Sheet Tray
Allows you to specify and display the paper tray that is inserting slip sheets.
After selecting the paper tray, you can also specify the display timing and
copy method for two-sided copying.
Note
❒ Default:
• Tray to Program: Off
❒ When [At Mode Selected] is selected, slip sheet tray settings only appear
when the cover function or slip sheet function is selected.
Reference
"Slip Sheets", Copy Reference
57
RussianC3_ENgsg-F_FM.book Page 58 Monday, June 16, 2003 6:48 PM
User Tools (System Settings)
Timer Settings
❖ Auto Off Timer
After a specified period has passed, following job completion, the machine
automatically turns off, in order to conserve energy. This function is called
"Auto Off".
The machine status after the Auto Off operation is referred to as "Off mode",
or "Sleep mode". For the Auto Off Timer, specify the time to elapse before
Auto Off.
Note
❒ Default: 1 minute
❒ Enter a time interval between 10 seconds and 240 minutes, using the number keys
❒ From “Off mode” or “Sleep mode”, the machine is ready to use within 10
seconds.
❒ Auto Off may not work when error messages appear.
4
❖ Panel Off Timer
Set the amount of time the machine waits before switching the panel off after
copying has finished or performing the last operation.
Note
❒ Default: 1 minute
❒ Enter a time interval between 10 seconds and 240 minutes, using the number keys.
❖ System Auto Reset Timer
The System Reset setting automatically switches the screen to that of the function set in Function Priority. When no operations are in progress, or when an
interrupted job is cleared. This setting determines the system reset interval.
See p.51 “Function Priority”.
Note
❒ Default: ON, 60 seconds
❒ The time can be set from 10 to 999 seconds, using the number keys.
❖ Copier/Document Server Auto Reset Timer (copier/Document Server)
Specifies the time to elapse before copier and Document Server modes reset.
Note
❒ If [OFF] is selected, the machine does not automatically switch to the user
code entry screen.
❒ Default: ON, 60 seconds
❒ The time can be set from 10 to 999 seconds, using the number keys.
58
RussianC3_ENgsg-F_FM.book Page 59 Monday, June 16, 2003 6:48 PM
Settings You Can Change with User Tools
❖ Facsimile Auto Reset Timer (facsimile)
Specifies the time to elapse before the facsimile mode resets.
Note
❒ Default: 30 seconds
❒ The time can be set from 30 to 999 seconds, using the number keys.
❖ Scanner Auto Reset Timer (scanner)
Specifies the time to elapse before the scanner function resets.
Note
❒ If [OFF] is selected, the machine does not automatically switch to the user
code entry screen.
❒ Default: ON, 60 seconds
❒ The time can be set from 10 to 999 seconds, using the number keys.
4
❖ Set Date
Set the date for the copier's internal clock using the number keys.
Note
❒ To change between year, month, and day, press [←
←] and [→
→].
❖ Set Time
Set the time for the copier's internal clock using the number keys.
Note
❒ To change between hours, minutes and seconds, press [←
←] and [→
→].
❒ Enter the time using the 24–hour format (in 1 second increments).
Key Operator Tools
The key operator must set the following items. For settings or more information,
contact the key operator.
The key operator is recommended to program an key operator code when performing the settings. See p.60 “Key Operator Code”.
❖ User Code Management
Allows you to control who uses the machine by setting codes for users.
User codes must be registered for user code management. See p.70 “User
Codes”.
Note
❒ Default: Copier/OFF, Document Server/OFF, Facsimile/OFF, Scanner/OFF,
Printer/Auto Program
❒ By using Auto Program for the printer, you can keep a print log for each
user code entered from the driver.
59
RussianC3_ENgsg-F_FM.book Page 60 Monday, June 16, 2003 6:48 PM
User Tools (System Settings)
❖ Key Counter Management
Use the key counter to specify whether users are restricted or not.
Note
❒ Default: Copier/OFF, Document Server/OFF, Facsimile/OFF, Scanner/OFF,
Printer/OFF
❖ External Charge Unit Management
Use the external charge unit to manage usage charges.
Note
❒ Default: Copier/OFF, Document Server/OFF, Facsimile/OFF, Scanner/OFF,
Printer/OFF
❖ Key Operator Code
Specifies whether or not to use passwords (max. eight digits) to control Key
Operator Tools settings for key operator codes.
4
Note
❒ Default: OFF
❒ If you select [ON], enter the key operator code (max. eight digits) using the
number keys, and then select [Partial] or [All Initial Settings] to set the access
limit.
• If you selected [Partial]
An key operator code is only required for the Timer Setting, Key Operator Tools for System Settings, and Key Operator Tools for Facsimile
Features. [Menu Protect] can be set for [Maintenance] in Printer Features. If
you set [Menu Protect], you can set the key operator code for some Printer
Features. See "Printer Features Parameters", Printer Reference 2.
• If you selected [All Initial Settings]:
An key operator code is required to access all items in System Settings,
Copier/Document Server Features, Facsimile Features, Printer Features, and Scanner Features.
❒ If you select [All Initial Settings], you must enter an key operator code to access the Key Operator Code display.
❖ Extended Security
Specify whether or not to use the security function.
Note
❒ Default : OFF
❒ You have to set a 6-digit key operator code to enable Extended Security.
See p.60 “Key Operator Code”.
❒ When the Extended Security function is on, a security mark
appears on
the left side of the date, in the upper right of the display panel.
Reference
For details about security, see p.145 “Security”.
60
RussianC3_ENgsg-F_FM.book Page 61 Monday, June 16, 2003 6:48 PM
Settings You Can Change with User Tools
❖ Display/Print Counter
Allows you to view and print the number of prints.
• Display/Print Counter
Displays the number of prints for each function (Total, Copier, Facsimile,
Printer, A3/DLT, Duplex, and Staple).
• Print Counter List
Prints out a list of the number of prints made under each function.
• To print the counter list:
A Press the {User Tools/Counter}
} key.
B Press [System Settings].
C Press [Key Operator Tools].
D Press [Display/Print Counter].
E Press [Print Counter List].
F
G
4
Press the {Start}
} key.
Press [Exit].
❖ Display/Clear/Print Counter per User Code
Allows you to view and print the numbers of prints accessed with user codes,
and to set those values to 0.
Note
❒ Press [U
U] and [T
T] to show all the numbers of prints.
❒ The number of prints may differ from the counter value shown in Display/Print Counter.
• Print counter per user code
Prints the number of prints made under each user code
• Clear counter per user code
Sets the number of prints made under each user code to 0.
Note
❒ Print list for each user code, see p.74 “Printing the Counter for Each User
Code”.
• Print counter for all user codes
Prints the number of prints made under all user codes.
• Clear counter for all user codes
Sets the number of prints made under all user codes to 0.
61
RussianC3_ENgsg-F_FM.book Page 62 Monday, June 16, 2003 6:48 PM
User Tools (System Settings)
❖ Print Address Book: Destination List
You can print the destination list registered in the Address Book.
• Print in Title 1 Order
Prints the Address Book in Title 1 order.
• Print in Title 2 Order
Prints the Address Book in Title 2 order.
• Print in Title 3 Order
Prints the Address Book in Title 3 order.
• Print Group Dial List
Prints the group Address Book.
A Select the print format.
B To print the list on two-sided pages, select [Print on 2 Sides].
C Press the {Start}
} key.
The list prints out.
4
❖ Address Book Management
You can add, change, or delete user information in the Address Book, and facsimile/scanner functions destinations.
For details about these operations, see p.70 “User Codes”, p.76 “Fax Destination”, and p.82 “E-mail Destination”, p.85 “Registering Folders”, p.93 “Registering a Protection Code”.
• [Program/Change]
This registers new user codes. You can register and change the items below:
• User Name
User (destination) name, key display, registration number, title selection
• User Code
User code, available functions
• Fax Dest.
Fax number, international TX mode, fax header, label insertion
• E-mail
E-mail address, sender registration
• Folder
Protocol, path, user name, password, port no., server name
• Protect Dest.
Sender's name, folder, protection code
• Group
• [Delete]
Deletes a user.
62
Note
❒ You can register up to 100 user codes. If you add the optional User Account
Enhance Unit, you can register up to 500 user codes.
❒ You can also register user codes using SmartNetMonitor for Admin (printer option required).
❒ You can also register user codes using a Web browser.
RussianC3_ENgsg-F_FM.book Page 63 Monday, June 16, 2003 6:48 PM
Settings You Can Change with User Tools
❖ Address Book: Program/Change/Delete Group
You can register multiple users in a group.
This allows you to easily control registered users in each group.
For details about operations, see p.95 “Registering Destinations to a Group”.
• [Program/Change]
This registers new groups, or changes the group name, key display, title selection, registration number or protection code. You can also protect e-mail
destinations and folders.
• [Delete]
Deletes a group.
• [Protect Dest.]
Note
❒ You can register up to 100 groups.
❒ You can also group users (destinations) using a Web browser. See the Web
browser's Help.
4
❖ Address Book: Program/Change/Delete Transfer Request
You can register fax destinations for the Transfer Request function in facsimile mode.
For details about operations, see p.99 “Registering the Transfer Request”.
• [Program/Change]
This registers new transfer requests and receiving stations, or changes the
transfer request name, key name, title selection, registration number, fax
destination or e-mail address.
• [Delete]
Deletes a transfer request.
Note
❒ You can register up to 100 transfer requests.
63
RussianC3_ENgsg-F_FM.book Page 64 Monday, June 16, 2003 6:48 PM
User Tools (System Settings)
❖ Address Book: Change Order
Changes the order of registered users (destinations).
Note
❒ You can rearrange the order of items on the same page, but you cannot
move items to another page. For example, you cannot move an item from
“PLANNING” ([OPQ]) to “DAILY” ([CD]).
A Press the {User Tools/Counter}
} key.
B Press [System Settings].
C Press [Key Operator Tools], and then press [T
TNext].
D Press [Address Book: Change Order].
4
E
Press the user (destination) key you want to move.
F
Note
❒ You can select a user using the number key.
Press the user (destination) key that is in the place you want to move to.
The user (destination) moves to the selected place, and the other users'
keys will shift also.
Note
❒ You can select a user using the number key.
64
RussianC3_ENgsg-F_FM.book Page 65 Monday, June 16, 2003 6:48 PM
Settings You Can Change with User Tools
❖ Address Book: Edit Title
You can edit the title to easily find a user.
A Press the {User Tools/Counter}
} key.
B Press [System Settings].
C Press [Key Operator Tools], and then press [T
TNext].
D Press [Address Book: Edit Title].
E
Press the title key you want to change.
F
Enter the new name, and then press [OK].
Press [OK].
Press [Exit].
G
H
4
❖ Address Book: Select Title
Specifies the title to select a user.
Note
❒ Default: Title 1
❖ Auto Delete File
Specifies whether documents stored in the Document Server are to be deleted
or not after a specified period of time elapses.
Note
❒ Default: Yes After 3 days
❒ If you select [Yes], documents stored subsequently are deleted after the
specified period.
❒ If you select [No], documents are not automatically deleted.
❒ If you select [Yes], enter a number of days from of 1 to 180 (in 1 day increments).
❒ The default is three days, this means documents are deleted three days (72
hours) after they are stored.
65
RussianC3_ENgsg-F_FM.book Page 66 Monday, June 16, 2003 6:48 PM
User Tools (System Settings)
❖ Delete All Files
Deletes all documents stored in the Document Server.
Note
❒ Even if a password is already set, all documents are deleted.
❒ A confirmation message appears. To delete all documents, select [Yes].
❖ Password Management for Stored Files
• Unlocking a locked document
When a document is locked due to a wrong password being entered, this
function unlocks the document, allowing access.
• Temporarily disabling document security
Password-protected documents can be temporarily accessed, without entering the password.
4
Note
❒ Default: Do not Unlock
❒ Select [Unlock] only when you forget the password. After accessing the
document, be sure to select [Do not Unlock].
Reference
p.147 “Unlocking a locked document”
p.147 “Temporarily Disabling Document Security”
❖ AOF (Always ON)
Specify whether or not to use Auto Off.
Note
❒ Default: ON
❖ Program/Change LDAP Server
Programming an LDAP server allows you to look up e-mail destinations from
the LDAP server Address Book directly. This function is available when you
send scan files by e-mail in scanner mode.
You can program and change the identification name, server name, search
base, port no., authentication, user name, password, and search options.
Reference
For details about these operations, see p.103 “Programming/Changing
LDAP Server”.
❖ Use LDAP Server
Specify whether or not to use the LDAP server.
Note
❒ Default: OFF
❒ If you select [OFF], [Search LDAP] will not appear on the searching display.
66
RussianC3_ENgsg-F_FM.book Page 67 Monday, June 16, 2003 6:48 PM
Address Book
Address Book
Registering user information, such as
fax number and e-mail address, in the
Address Book allows you to manage
them together.
Important
❒ Address Book data is stored on the
hard disk. It can be lost if there is
some kind of hard disk failure. The
manufacturer shall not be responsible for any damage resulting
from data loss.
Note
❒ Using [Address Management Tool] in
SmartNetMonitor for Admin, you
can backup Address Book data.
We recommend backing up data
when using the Address Book.
Reference
For details about SmartNetMonitor for Admin and how to install it,
see Printer Reference 1.
For operating instructions, see
S m art Ne tM o nit or fo r A dm i n
Help.
You can register and manage the following items in the Address Book:
Reference
p.70 “User Codes”
2. Protect Dest.
Reference
p.69 “When using the scanner
function”
p.69 “Registering Sender Information”
3. Group
Use this to display the group that
the selected user (destination) belongs to.
You can group registered fax destinations, e-mail destinations, and
folders to manage them better. For
details about operations, see p.95
“Registering Destinations to a
Group”.
4
❖ Items to register
4. User Name
Reference
p.68 “Registering the destination name and key display”
p.69 “Registering Sender Information”
5. Fax Dest.
Reference
p.68 “When using the fax function”
4
1
5
6
7
2
3
ZKZS030E
❖ To manage registered items
1. User Code
Register user codes to restrict particular functions to certain users,
and check their use of each function.
67
RussianC3_ENgsg-F_FM.book Page 68 Monday, June 16, 2003 6:48 PM
User Tools (System Settings)
6. E-mail
Reference
p.68 “When using the fax function”
p.69 “When using the scanner
function”
p.69 “Registering Sender Information”
Registering Destination
Information
❖ Registering the destination name and
key display
• User Name
Register the destination name
and key display name. This is
the basic information required
for managing destinations.
Reference
p.70 “User Codes”
4
7. Folder
Reference
p.69 “When using the scanner
function”
• SMB
• FTP
❖ When using the fax function
• Fax Dest.
Register fax numbers in the Address Book. To send a fax, select
the destination key as it appears
on the initial fax function display, so you can specify the fax
number. When you set Label Insertion to ON, the registered
destination name, preceded by
“To”, is printed at the top of the
page when it is received at the
other end.
Reference
p.76 “Fax Destination”
• E-mail
Register e-mail addresses in the
Address Book. To send an Internet Fax, select the destination
key as it appears on the initial
fax function display, so you can
specify the e-mail address.
Reference
p.82 “E-mail Destination”
68
RussianC3_ENgsg-F_FM.book Page 69 Monday, June 16, 2003 6:48 PM
Address Book
❖ When using the scanner function
• E-mail
Register e-mail addresses in the
Address Book. To send a scan
file by e-mail, select the destination key as it appears on the initial scanner function display, so
you can specify the e-mail address.
Reference
p.82 “E-mail Destination”
• Folder
Register the path name, user
name, and password. To send
files directly to shared folders,
select the destination key as it
appears on the initial scanner
function display, so you can
specify the folder.
Select SMB when sending files
to shared Windows folders.
Select FTP when uploading files
to an FTP server.
Reference
p.85 “Registering Folders”
You can stop unauthorized users accessing folders from the
machine by setting a protection
code.
Reference
p.93 “Registering a Protection Code”
Registering Sender
Information
❖ When using the scanner function
You can set Register as Sender to
ON for an e-mail address. If you do
this, you can use it as the sender
address when sending scan files by
e-mail.
• User Name
Register the user name and key
display name. This is useful
when selecting the sender from
the Attach Sender's Name list.
Register the user name so it will
be recorded under Sender in
Scanned Files Status. Also, the
user name automatically appears in the From field of the email.
4
Reference
p.70 “User Codes”
• E-mail
Register the e-mail address. You
can use it as the sender address
when sending scan files by email using the scanner function.
Also, the sender address automatically appears in the From
field of the e-mail.
To display a user key on the Attach Sender's Name list, you
must register an e-mail address
to it.
Reference
p.82 “E-mail Destination”
You can prevent misuse of
sender name by setting a protection code on the e-mail address.
Reference
p.93 “Registering a Protection Code”
69
RussianC3_ENgsg-F_FM.book Page 70 Monday, June 16, 2003 6:48 PM
User Tools (System Settings)
User Codes
Register user codes to limit users to
the following functions and check
their use of each function:
• Copier
• Document Server
• Facsimile
• Scanner
• Printer
Note
❒ The number of copies made of documents stored in the Documents
Server using the facsimile function
is counted for each user code. This
allows you to check each user's usage.
❒ The number of copies scanned using the scanner function is counted
for each user code. This allows you
to check each user's usage.
❒ To automatically register the printer driver user code, select [Auto Program] for the printer in User Code
Management. To use the user code
set in User Tools, select [ON]. Set
the user codes registered in User
Tools for the printer driver. See
p.59 “User Code Management”.
4
Reference
For details about setting user codes
for the printer driver, see Printer
Reference 1 or the printer driver
Help.
Important
❒ The functions associated with each
user code are the same. If you
change or delete user codes, management data and limits associated
with that code become invalid.
70
Registering a New User Code
A Press the {User Tools/Counter}} key.
B Press [System Settings].
C Press [Key Operator Tools], and then
press [T
TNext].
D Press [Address Book Management].
E Press [New Program].
Note
❒ To assign a user code to a registered user, press the user (destination) key whose user code is
to be registered, or enter the
registered number using the
number keys.
F Set the user information.
Note
❒ To register a user code to a registered user, proceed to step G.
RussianC3_ENgsg-F_FM.book Page 71 Monday, June 16, 2003 6:48 PM
User Codes
To register the user name and
key display
A Press [Change] on the right of
the user name or key display.
The user name or key display
entry display appears.
B Enter the user name or key display, and then press [OK].
Note
❒ You can use the same user
name as that assigned to the
documents using the Document Server function. For
this, the user code is not neces s ary . p . 33 “ D o c u m e n t
Server”
Reference
p.143 “Entering Text”
To select the title
G Press [User Code].
H Enter the user code
using the
number keys, and then press [#].
Note
❒ If you make a mistake, press
[Clear] or the {Clear/Stop}
} key,
and then enter the code again.
4
I Select
the functions to be used
with the user code from Available
Functions.
J To
continue registering user
codes, press [Continue to Program],
and then repeat the procedure
from step F.
A Press the key for the classification you want to use under Select Title.
Note
❒ The keys you can select are as
follows:
• [Freq.]… Added to the
page that is displayed first.
• [AB],[CD],[EF],[GH],[IJK],
[LMN],[OPQ],[RST],[UV
W],[XYZ], [1] to [10]…
Added to the list of items
in the title selected.
❒ You can select [Freq.] and one
more page for each title.
K Press [OK].
L Press [Exit].
M Press the {User Tools/Counter}} key.
71
RussianC3_ENgsg-F_FM.book Page 72 Monday, June 16, 2003 6:48 PM
User Tools (System Settings)
Changing a User Code
Changing the user code
Note
❒ Even if you change a user code, the
counter value will not be cleared.
A Press [User Code].
B Press [Change], and then enter
the new user code using the
number keys.
A Press the {User Tools/Counter}} key.
B Press [System Settings].
C Press [Key Operator Tools], and then
press [T
TNext].
D Press [Address Book Management].
E Select the registered user code
4
you want to change.
Press the user (destination) key, or
enter the registered number using
the number keys.
Note
❒ If you press , you can search
for a user by user name/index,
user code, fax destination, or email address.
F Enter the new information for the
item you want to change.
To change the user (destination)
name or key display
A Press [Change] on the right of
the user (destination) name or
key display.
B Enter the user (destination)
name, and then press [OK].
Reference
p.143 “Entering Text”
To change the title
A Press the key for the classification you want to use from Select Title.
72
C Press [#].
To change the available functions
A Press [User Code].
B Press the key to select the functions to enable.
Note
❒ Press the key to highlight it,
and then the function is enabled.
G Press [OK].
H Press [Exit].
I Press the {User Tools/Counter}} key.
RussianC3_ENgsg-F_FM.book Page 73 Monday, June 16, 2003 6:48 PM
User Codes
Deleting a User Code
To delete a user (destination)
Important
❒ This operation also deletes user
codes registered to multiple functions. User control via the deleted
user code is disabled.
A Press [Delete].
B Select the user (destination)
you want to delete.
Press the user (destination) key,
or enter the registered code using the number keys.
A Press the {User Tools/Counter}} key.
B Press [System Settings].
C Press [Key Operator Tools], and then
press [T
TNext].
D Press [Address Book Management].
To delete the user code
A Select the user (destination)
whose code is to be deleted.
Press the user (destination) key,
or enter the registered code using the number keys.
B Press [User Code].
C Press [Change] to delete the user
code, and then press [#].
D Press [OK].
Note
❒ If you press
, you can
search for a user by user
name/index, user code, fax
destination, or e-mail address.
C Press [Yes] in the confirmation
screen.
4
E Press [Exit].
F Press the {User Tools/Counter}} key.
Displaying the Counter for
Each User Code
You can check the number of prints
made under each function's user
code.
A Press the {User Tools/Counter}} key.
B Press [System Settings].
C Press [Key Operator Tools].
D Press [Display/Clear/Print Counter per
User Code].
E Select [Print Counter], [Transmission
Counter] or [Scanner Counter].
Counters for individual function
usage under each user code appear.
73
RussianC3_ENgsg-F_FM.book Page 74 Monday, June 16, 2003 6:48 PM
User Tools (System Settings)
Printing the Counter for Each
User Code
You can print out the number of
prints made under each user code using [Print Counter], [Transmission
Counter] or [Scanner Counter].
To print the number of prints made
under each user code
A Press the {User Tools/Counter}} key.
B Press [System Settings].
C Press [Key Operator Tools].
D Press [Display/Clear/Print Counter per
4
User Code].
E Select
G Select
the function usage you
want to print from [Print Counter],
[Transmission Counter], and [Scanner
Counter].
H Press [Print].
To print the number of prints for all
user codes
A Press the {User Tools/Counter}} key.
B Press [System Settings].
C Press [Key Operator Tools].
D Press [Display/Clear/Print Counter per
User Code].
E Press [Print Counter List] under All
User Codes.
a user code from the left
side of the display.
Note
❒ Press [Select all on the page] to select all user codes on the page.
F Press [Print Counter List] under Per
User Code.
Note
❒ Enter the user code, and then
press [#] if the user code is registered.
F Select
the function usage you
want to print from [Print Counter],
[Transmission Counter], and [Scanner
Counter].
G Press [Print].
Note
❒ Enter the user code, and then
press [#] if the user code is registered.
74
RussianC3_ENgsg-F_FM.book Page 75 Monday, June 16, 2003 6:48 PM
User Codes
Clearing the Number of Prints
A Press the {User Tools/Counter}} key.
B Press [System Settings].
C Press [Key Operator Tools].
D Press [Display/Clear/Print Counter per
To clear the number of prints for
all user codes
A Press [Clear] under All User
Codes.
User Code].
E Select the user code to clear.
To clear the number of prints
made under a user code
A Select the user code from the
left side of the display.
B Select the function usage you
want to clear from [Print
Counter], [Transmission Counter],
and [Scanner Counter].
C Press [OK].
4
Note
❒ Press [Select all on the page] to
select all user codes on the
page.
B Press [Clear] under Per User
Codes.
C Select the function usage you
want to clear from [Print
Counter], [Transmission Counter],
and [Scanner Counter].
D Press [OK].
75
RussianC3_ENgsg-F_FM.book Page 76 Monday, June 16, 2003 6:48 PM
User Tools (System Settings)
Fax Destination
Register a fax destination so you do
not need to enter fax numbers each
t i m e , an d c a n s e n d d o c u m e n t s
scanned in using the facsimile function.
• It is easy to select the fax destination if you register a “User (Destination) Name” and “Key Display”
for the fax destination.
• You can register fax destinations as
a group.
You can program the following items
in a fax destination:
4
❖ Fax number
Registers the destination's fax
number. You can enter a fax number using up to 128 digits. You
must include every digit in the
number.
❖ SUB Code
Registering a SUB Code allows
you to use Confidential Transmission to send messages to the other
fax machines which support a similar function called “SUB Code”.
You can also program an SID Code
(Sender ID) under this function. A
code can be up to 20 digits long.
❖ SEP Code
Registering a SEP Code allows you
to use Polling Reception to receive
faxes from the other fax machines
which support Polling Reception.
You can also program a PWD
Code when you want to use a password under this function. A code
can be up to 20 digits long.
76
❖ Line
If the optional extra G3 interface
unit is installed, you can select the
line type per destination.
❖ Fax header
You can select to print a fax header
on fax messages the other party receives. The default is “1st Name”.
See Facsimile Reference <Advanced
Features>.
❖ Label insertion
With this function you can have
the receiver's name printed on the
message when it is received at the
other end. The name is printed at
the top of the page and will be preceded by “To”. You can also have a
standard message stamped on the
second and third lines after that.
Note
❒ Fax header and label insertion
are also printed when sending
by e-mail using fax functions.
❒ You can program a standard
message apart from one of those
registered in the machine. See
“Programming, Changing, and
Deleting Standard Messages”,
Facsimile Reference <Advanced
Features>.
❖ International TX mode
When setting the International TX
mode to [ON], the machine transmits more carefully by lowering
transmission speed. However,
communication times increase.
RussianC3_ENgsg-F_FM.book Page 77 Monday, June 16, 2003 6:48 PM
Fax Destination
Registering a Fax Destination
A Press the {User Tools/Counter}} key.
B Press [System Settings].
C Press [Key Operator Tools], and then
press [T
TNext].
D Press [Address Book Management].
E Press [New Program].
Note
❒ To register a fax destination to a
registered user, press the user
(destination) key, or enter the
registered number using the
number keys.
F Set the user's information.
Note
❒ To register a fax destination to a
registered user, proceed to step
G.
To register the user (destination)
name and key display
A Press [Change] under User (Destination) Name or Key Display.
The user (destination) name or
key display entry display appears.
B Enter the user (destination)
name or key display, and then
press [OK].
Note
❒ You can use the user name
when selecting a fax destination.
❒ You can register the user
code after the user name. For
details, see p.70 “User
Codes”.
4
Reference
p.143 “Entering Text”
To select the title
A To associate a user with a title,
press the title key under Select
Title.
Note
❒ The keys you can select are as
follows:
• [Freq.]… Added to the
page that is displayed first.
• [AB], [CD], [EF], [GH],
[ I J K] , [ L MN ] , [ O P Q ] ,
[RST], [UVW], [XYZ], [1] to
[10]… Added to the list of
items in the selected title.
❒ You can select [Freq.], and
one more page for each title.
77
RussianC3_ENgsg-F_FM.book Page 78 Monday, June 16, 2003 6:48 PM
User Tools (System Settings)
G Press [Fax Dest.].
H Enter the fax number
using the
number keys, and then press [OK].
To select the line
A Press [Select Line].
4
To program the SEP Code
A Press [Adv. Features], and then
select [SEP Code].
B Press [Change] under RX SEP
Code.
C Enter a SEP Code using the
number keys, and then press
[OK].
D To enter a password, press
[Change ] u nd er P as sw or d
(PWD).
E Enter a password using the
number keys, and then press
[OK].
F Press [OK].
To set the International TX mode
B Select the line, and then press
[OK].
To program the SUB Code
A Press [Adv. Features], and then
select [SUB Code].
B Press [Change] under TX SUB
Code.
C Enter a SUB Code using the
number keys, and then press
[OK].
D To enter a password, press
[Change ] un der Pas sw ord
(SID).
E Enter a password using the
number keys, and then press
[OK].
F Press [OK].
78
A Press [Change] under International TX Mode.
B Select [OFF] or [ON], and then
press [OK].
To select the fax header
Note
❒ You can register the fax header
name in Program Fax Information under the system settings
of Facsimile Features. See Facsimile Reference <Advanced Features>.
A Press [Change] under Fax Header.
B Select [1st Name] or [2nd Name],
and then press [OK].
RussianC3_ENgsg-F_FM.book Page 79 Monday, June 16, 2003 6:48 PM
Fax Destination
To set label insertion
When Label Insertion is set to ON,
the receiver's name and standard
messages are printed on the fax
message when it is received at the
other end.
A Press [Change] under Label Insertion.
B Select [ON].
C Press [Change] under Line 2.
D Select a standard message to
print on the second line. To
stamp a customized message,
press [Custom Message].
E Enter a message, and then
press [OK].
Reference
p.143 “Entering Text”
F Press [OK].
G Press [Change] under Line 3.
H Select a standard message, and
then press [OK].
I Press [OK].
Changing a Registered Fax
Destination
A Press the {User Tools/Counter}} key.
B Press [System Settings].
C Press [Key Operator Tools], and then
press [T
TNext].
D Press [Address Book Management].
E Select the registered fax destina-
tion user you want to change.
Press the user (destination) key, or
enter the registered number using
the number keys.
4
Note
❒ If you press , you can search
for a user by user name/index,
user code, fax destination, or email address.
F Press [Fax Dest.].
G Enter the items.
To change the fax number
A Press [Change] under Facsimile
No..
I Press [OK].
Note
❒ When a group is registered, you
can add this fax destination to
the group. See p.95 “Registering
Destinations to a Group”.
B Enter the new fax number using the number keys, and then
press [OK].
79
RussianC3_ENgsg-F_FM.book Page 80 Monday, June 16, 2003 6:48 PM
User Tools (System Settings)
To change the line
To change the fax header
A Press [Select Line].
A Press [Change] under Fax Header.
B Select the fax header, and then
press [OK].
To change the label insertion
B Select the line type.
C Press [OK].
To change the SUB Code
4
A Press [Adv. Features].
B Press [SUB Code].
C Press [Change] under TX SUB
Code.
D Enter the new SUB Code, and
then press [OK].
E To change the password, press
[Change ] un der Pas sw ord
(SID).
F Enter the new password, and
then press [OK].
G Press [OK].
To change the SEP Code
A Press [Adv. Features].
B Press [SEP Code].
C Press [Change] under RX SEP
Code.
D Enter the new SEP Code, and
then press [OK].
E To change the password, press
[Change ] un der Pas sw ord
(PWD).
F Enter the new password, and
then press [OK].
G Press [OK].
80
A Press [Change] under Label Insertion.
B Press [Change] under Line 2.
C Select the new standard message, or press [Custom Message]
to enter the new message.
D Press [OK].
E Press [Change] under Line 3.
F Select the new standard message, and then press [OK].
G Press [OK].
H Press [OK].
Note
❒ To change the user name, see
p.72 “To change the user (destination) name or key display”.
RussianC3_ENgsg-F_FM.book Page 81 Monday, June 16, 2003 6:48 PM
Fax Destination
Deleting a Registered Fax
Destination
Note
❒ If you delete a destination that is a
specified delivery destination,
messages to its registered Personal
Box, for example, cannot be delivered. Be sure to check the settings
in the fax function before deleting
any destinations.
A Press the {User Tools/Counter}} key.
B Press [System Settings].
C Press [Key Operator Tools], and then
press [T
TNext].
To delete all user information
A Press [Delete].
B Select a user you want to delete.
Press the user (destination) key,
or enter the registered number
using the number keys.
C Press [Yes].
E Press [Exit].
Note
❒ To delete user codes together,
see p.73 “Deleting a User
Code”.
4
F Press the {User Tools/Counter}} key.
D Press [Address Book Management].
To delete only the fax number
A Select the fax destination user
you want to delete.
Press the user (destination) key,
or enter the registered number
using the number keys.
B Press [Fax Dest.].
C Press [Change] under Facsimile
No..
D Press [Delete All], and then press
[OK].
E Press [OK].
81
RussianC3_ENgsg-F_FM.book Page 82 Monday, June 16, 2003 6:48 PM
User Tools (System Settings)
E-mail Destination
Register e-mail destinations so you
do not need to enter an e-mail address
every time, and can send scan files
from scanner or fax function by email.
• It is easy to select the e-mail destination if you register “User (Destination) Name” and “Key Display”
as the e-mail destination.
• You can register e-mail destinations as a group.
• You can use the e-mail address as
the sender's address when sending
scan files in scanner mode. If you
do this, set a protection code on the
sender address to prevent use by
unauthorized people. See p.93
“Registering a Protection Code”.
• You can select an e-mail address
from an LDAP server, and then
register it in the Address Book. For
details about programming an
LDAP server, See p.103 “Programming/Changing LDAP Server”.
For details about searching an email address from an LDAP server, See “Sending Scan File by Email”, Scanner Reference.
4
Registering an E-mail
Destination
A Press the {User Tools/Counter}} key.
B Press [System Settings].
C Press [Key Operator Tools], and then
press [T
TNext].
D Press [Address Book Management].
E Press [New Program].
Note
❒ To register an e-mail address to
a registered user, press the user
(destination) key, or enter the
registered number using the
number keys.
F Set the user's information.
Note
❒ To register an e-mail address to
a registered user, proceed to
step G.
82
RussianC3_ENgsg-F_FM.book Page 83 Monday, June 16, 2003 6:48 PM
E-mail Destination
To register the user (destination)
name and key display
A Press [Change] under User (Destination) Name or Key Display.
The user (destination) name or
key display entry display appears.
B Enter the user (destination)
name or key display, and then
press [OK].
Note
❒ You can use the user name
when selecting an address to
send an e-mail to.
❒ You can register the user code
after the user name. For details, see p.70 “User Codes”.
Reference
p.143 “Entering Text”
To select the title
A To associate a user with a title,
press the title key under Select
Title.
G Press [E-mail].
H Press [Change] under E-mail Address.
I Enter the e-mail address.
Entering the e-mail address
4
A Enter the e-mail address.
B Press [OK].
Using the e-mail address as the
sender
A Press [ON] under Register as
Sender.
J Press [OK].
Note
❒ The keys you can select are as
follows:
• [Freq.]… Added to the
page that is displayed first.
• [AB], [CD], [EF], [GH],
[ I J K ] , [ L MN ] , [ O P Q ] ,
[RST], [UVW], [XYZ], [1] to
[10]… Added to the list of
items in the selected title.
❒ You can select [Freq.] and one
more page for each title.
Note
❒ When a group is registered, other e-mail destinations can be
added to the group. See p.95
“Registering Destinations to a
Group”.
83
RussianC3_ENgsg-F_FM.book Page 84 Monday, June 16, 2003 6:48 PM
User Tools (System Settings)
Changing a Registered E-mail
Destination
A Press the {User Tools/Counter}} key.
B Press [System Settings].
C Press [Key Operator Tools], and then
press [T
TNext].
D Press [Address Book Management].
E Select the registered e-mail address user you want to change.
Press the user (destination) key, or
enter the registered number using
the number keys.
4
Note
❒ If you press , you can search
for a user by user name/index,
user code, fax destination, or email address.
F Press [E-mail].
G Enter the items.
To change the e-mail address
A Press [Change] under E-mail
Address.
H Press [OK].
Note
❒ To change the user name, see
p.72 “To change the user (destination) name or key display”.
Deleting a Registered E-mail
Destination
A Press the {User Tools/Counter}} key.
B Press [System Settings].
C Press [Key Operator Tools], and then
press [T
TNext].
D Press [Address Book Management].
To delete only the e-mail address
A Select the e-mail address user
you want to delete.
Press the user (destination) key,
or enter the registered number
using the number keys.
B Press [E-mail].
C Press [Change] under E-mail
Address.
D Press [Delete All], and then press
[OK].
E Press [OK].
To delete all user information
B Enter the e-mail address, and
then press [OK].
Reference
p.143 “Entering Text”
A Press [Delete].
B Select a user you want to delete.
Press the user (destination) key,
or enter the registered number
using the number keys.
C Press [Yes].
E Press [Exit].
84
RussianC3_ENgsg-F_FM.book Page 85 Monday, June 16, 2003 6:48 PM
Registering Folders
Registering Folders
By registering a shared folder, you
can send scan files to it directly.
There are two types of protocol you
can use:
• SMB
For sending files to shared Windows folders
• FTP
Use when sending files to an FTP
server.
Note
❒ For details about protocols, server
names, and folder levels, ask your
network administrator.
❒ You can stop unauthorized users
accessing folders from the machine. See p.93 “Registering a Protection Code”.
❒ You can only select either SMB or
FTP. If you change protocol after
finishing your settings, all previous entries are cleared.
❒ You can register up to 50 folders
per group. Files cannot be sent to a
group with over 50 folders registered.
Reference
For details about network settings,
see Network Guide.
For details about Scan to Folder,
see Scanner Reference.
Using SMB to Connect
Note
❒ To register a folder in an FTP server, see p.89 “Using FTP to Connect”.
To register an SMB folder
A Press the {User Tools/Counter}} key.
4
B Press [System Settings].
C Press [Key Operator Tools], and then
press [T
TNext].
D Press [Address Book Management].
E Press [New Program].
Note
❒ To register a folder to a registered user, press the user (destination) key, or enter the
registered number using the
number keys.
85
RussianC3_ENgsg-F_FM.book Page 86 Monday, June 16, 2003 6:48 PM
User Tools (System Settings)
F Set the user's information.
Note
❒ To register a folder to a registered user, proceed to step G.
To select the title
A To associate a user with a title,
press the title key under Select
Title.
To register the user (destination)
name and key display
A Press [Change] under User
(Destination) Name or Key
Display.
The user (destination) name or
key display entry display appears.
B Enter the user (destination)
name or key display, and then
press [OK].
4
Note
❒ You can use the user name as
the folder name.
❒ You can register the user
code after the user name. For
details, see p.70 “User
Codes”.
Reference
p.143 “Entering Text”
Note
❒ The keys you can select are as
follows:
• [Freq.]… Added to the
page that is displayed first.
• [AB], [CD], [EF], [GH],
[ I J K] , [ L MN ] , [ O P Q ] ,
[RST], [UVW], [XYZ], [1] to
[10]… Added to the list of
items in the selected title.
❒ You can select [Freq.] and one
more page for each title.
G Press [Folder].
H Press [SMB].
Note
❒ To specify a folder, you can either enter the path manually, or
locate the folder by browsing
the network.
Reference
p.87 “To locate the folder manually”
p.87 “Using Browse Network to
locate the folder”
86
RussianC3_ENgsg-F_FM.book Page 87 Monday, June 16, 2003 6:48 PM
Registering Folders
To locate the folder manually
A Press [Change] under Path.
B Enter the path where the folder
is located.
Note
❒ Enter the path using this format: “\\ServerName\ShareName\PathName”.
❒ You can also enter an IP address.
❒ You can enter a path using
up to 128 characters.
C Press [OK].
Using Browse Network to locate
the folder
A Press [Browse Network].
The client computers sharing
the same network as the machine appear.
Note
❒ You can enter your user
name and password before
pressing [Browse Network]. If
you do, the Browse Network
display only lists client computers you are authorized to
access.
B Select a client computer.
Note
❒ If the format of the entered
path is not correct, a message
appears. Press [Exit], and
then enter the path again.
D Press [Change] under User
Name.
E Enter the user name, and then
press [OK].
Note
❒ You can press [Up One Level]
to switch between levels.
C Select the folder you want to
register.
The Logon display appears.
Note
❒ This is a user name which is
authorized to access the folder.
F Press [Change] under Password.
G Enter the user's password, and
then press [OK].
Note
❒ If you have already entered
an authorized user name and
password, the Logon display
will not appear. Proceed to
step F.
D Enter the user name.
4
Shared folders under it appear.
Note
❒ This is a user name which is
authorized to access the folder.
87
RussianC3_ENgsg-F_FM.book Page 88 Monday, June 16, 2003 6:48 PM
User Tools (System Settings)
E Enter the user's password, and
then press [OK].
The Browse Network display
reappears.
Note
❒ If the entered user name or
password is not correct, a
message appears. Press [Exit],
and then enter the user name
and password again.
G Select
the items you want to
change.
To change the protocol
A Press [FTP].
F Press [OK].
4
I Press [Connection Test] to check the
B A confirmation message appears. Press [Yes].
J Press [Exit].
Note
❒ Changing the protocol will
clear all settings made under
the previous protocol.
C Enter each item again.
path is set correctly.
Note
❒ If the connection test fails, check
the settings, and then try again.
K Press [OK].
Changing a registered SMB folder
A Press the {User Tools/Counter}} key.
B Press [System Settings].
C Press [Key Operator Tools], and then
press [T
TNext].
D Press [Address Book Management].
E Select the user of the registered
folder you want to change.
Press the user (destination) key, or
enter the registered number using
the number keys.
Note
❒ If you press , you can search
for a user by user name/index,
user code, fax destination, or email address.
F Press [Folder].
88
Reference
See steps I to T on p.89 “To
register an FTP folder”.
Changing items under SMB
A Press [Change] under Path.
B Enter the new path where the
folder is located, and then
press [OK].
Note
❒ You can also use Browse Network to specify a new folder.
For details, see p.87 “Using
Browse Network to locate
the folder”.
C Press [Change] under User
Name.
D Enter the new user name, and
then press [OK].
This is a user name which is authorized to access the folder.
E Press [Change] under Password.
F Enter the new password, and
then press [OK].
RussianC3_ENgsg-F_FM.book Page 89 Monday, June 16, 2003 6:48 PM
Registering Folders
H Press [Connection Test] to check the
path is set correctly.
I Press [Exit].
Note
❒ If the connection test fails, check
the settings, and then try again.
J Press [OK].
Note
❒ To change the user (destination)
name, see p.72 “Changing a
User Code”.
Deleting a registered SMB folder
A Press the {User Tools/Counter}} key.
B Press [System Settings].
C Press [Key Operator Tools], and then
press [T
TNext].
D Press [Address Book Management].
To delete all user information
A Press [Delete].
B Select a user you want to delete.
Press the user (destination) key,
or enter the registered number
using the number keys.
C Press [Yes].
E Press [Exit].
Using FTP to Connect
4
Note
❒ To register a shared folder configured in Windows, see p.85 “Using
SMB to Connect”.
To register an FTP folder
A Press the {User Tools/Counter}} key.
To delete only the registered
folder
A Select a user of the folder you
want to delete.
Press the user (destination) key,
or enter the registered number
using the number keys.
B Press [Folder].
C Press [FTP].
A confirmation message appears.
D Press [Yes].
E Press [OK].
Settings under SMB are all
cleared.
B Press [System Settings].
C Press [Key Operator Tools], and then
press [T
TNext].
D Press [Address Book Management].
89
RussianC3_ENgsg-F_FM.book Page 90 Monday, June 16, 2003 6:48 PM
User Tools (System Settings)
E Press [New Program].
Note
❒ To register a folder to a registered user, press the user (destination) key, or enter the
registered number using the
number keys.
To select the title
A To associate a user with a title,
press the title key under Select
Title.
F Set the user's information.
Note
❒ To register a folder to a registered user, proceed to step G.
4
To register the user (destination)
name and key display
A Press [Change] under User
(Destination) Name or Key
Display.
The user (destination) name or
key display entry display appears.
B Enter the user (destination)
name or key display, and then
press [OK].
Note
❒ You can use the user name as
the folder name.
❒ You can register the user
code after the user name. For
details, see p.70 “User
Codes”.
Reference
p.143 “Entering Text”
Note
❒ The keys you can select are as
follows:
• [Freq.]… Added to the
page that is displayed first.
• [AB], [CD], [EF], [GH],
[ I J K] , [ L MN ] , [ O P Q ] ,
[RST], [UVW], [XYZ], [1] to
[10]… Added to the list of
items in the selected title.
❒ You can select [Freq.] and one
more page for each title.
G Press [Folder].
H Press [FTP].
I Press [Change]
under
Server
Name.
J Enter the server name.
Note
❒ You can enter a server name using up to 64 characters.
K Press [Change] under Path.
L Enter the path.
90
RussianC3_ENgsg-F_FM.book Page 91 Monday, June 16, 2003 6:48 PM
Registering Folders
Note
❒ You can enter an absolute path,
using this format: “/user/home/username”; or a relative path, using this format:
“directory/sub-directory”.
❒ If you leave the path blank, the
login directory is assumed to be
the current working directory.
❒ You can also enter an IP address.
❒ You can enter a path using up to
128 characters.
M Press [OK].
Note
❒ To change the port number,
press [Change] under Port No..
Enter the port number using the
number keys, and then press [#].
You can enter 1 to 65535.
N Press [Change] under User Name.
O Enter the user name, and then
press [OK].
Note
❒ This is a user name which is authorized to access the folder.
Changing a registered FTP folder
A Press the {User Tools/Counter}} key.
B Press [System Settings].
C Press [Key Operator Tools], and then
press [T
TNext].
D Press [Address Book Management].
E Select the user of the registered
folder you want to change.
Press the user (destination) key, or
enter the registered number using
the number keys.
4
Note
❒ If you press , you can search
for a user by user name/index,
user code, fax destination, or email address.
F Press [Folder].
G Select the items
you want to
change.
To change the protocol
A Press [SMB].
P Press [Change] under Password.
Q Enter the user's password, and
then press [OK].
R Press [Connection Test] to check the
path is set correctly.
S Press [Exit].
Note
❒ If the connection test fails, check
the settings, and then try again.
T Press [OK].
B A confirmation message appears. Press [Yes].
Note
❒ Changing the protocol will
clear all settings made under
the previous protocol.
C Enter each item again.
Reference
See stepsH to K on p.85 “To
register an SMB folder”.
91
RussianC3_ENgsg-F_FM.book Page 92 Monday, June 16, 2003 6:48 PM
User Tools (System Settings)
4
Changing items under FTP
Deleting a registered FTP folder
A Press [Change] under Server
Name.
B Enter the new server name, and
then press [OK].
C Press [Change] under Path.
D Enter the new path, and then
press [OK].
E Press [Change] under User
Name.
F Enter the new user name, and
then press [OK].
This is a user name which is authorized to access the folder.
G Press [Change] under Password.
H Enter the new password, and
then press [OK].
A Press the {User Tools/Counter}} key.
B Press [System Settings].
C Press [Key Operator Tools], and then
D Press [Address Book Management].
To delete only the registered
folder
H Press [Connection Test] to check the
A Select a user of the folder you
want to delete.
Press the user (destination) key,
or enter the registered number
using the number keys.
B Press [Folder].
C Press [SMB].
A confirmation message appears.
D Press [Yes].
E Press [OK].
Set ting s und er F TP are all
cleared.
I Press [Exit].
To delete all user information
Note
❒ To change the port number,
press [Change] under Port
No.. Enter the new port number using the number keys,
and then press [#].
path is set correctly.
Note
❒ If the connection test fails, check
the settings, and then try again.
J Press [OK].
Note
❒ To change the user (destination)
name, see p.72 “Changing a
User Code”.
92
press [T
TNext].
A Press [Delete].
B Select a user you want to delete.
Press the user (destination) key,
or enter the registered number
using the number keys.
C Press [Yes].
E Press [Exit].
RussianC3_ENgsg-F_FM.book Page 93 Monday, June 16, 2003 6:48 PM
Registering a Protection Code
Registering a Protection Code
You can stop sender's names or folders being accessed by setting a protection code.
You can use this function to protect
the following:
• Folders
You can prevent unauthorized access to folders.
• Sender's names (when sending emails)
You can prevent misuse of sender's
names.
Note
❒ This function is not available
when using Internet Fax to send
e-mails.
D Press [Address Book Management].
E Press the user (destination) key
you want to register a protection
code to.
F Press [Protect Dest.].
4
To protect the sender name
A Press [Protect] under Sender's
Name.
Registering a Protection Code
To a Single User
A Press the {User Tools/Counter}} key.
To protect the folder
A Press [Protect] under Folder.
G Press
[Change] under Protection
Code.
H Enter a protection code using the
number keys, and then press [#].
B Press [System Settings].
Note
❒ You can enter up to eight digits.
I Press [OK].
J Press [Exit].
C Press [Key Operator Tools], and then
press [T
TNext].
93
RussianC3_ENgsg-F_FM.book Page 94 Monday, June 16, 2003 6:48 PM
User Tools (System Settings)
Registering a Protection Code
To a Group User
A Press the {User Tools/Counter}} key.
B Press [System Settings].
C Press [Key Operator Tools], and then
press [T
TNext].
D Press [Address Book: Program/Change/
Delete Group].
E Press the group key you want to
4
register a protection code to.
F Press [Protect Dest.].
G Press [Protect] under Folder.
H Press [Change] under Protection
Code.
I Enter a protection code using the
number keys, and then press [#].
Note
❒ You can enter up to eight digits.
J Press [OK].
K Press [Exit].
94
RussianC3_ENgsg-F_FM.book Page 95 Monday, June 16, 2003 6:48 PM
Registering Destinations to a Group
Registering Destinations to a Group
Register destinations to a group to
easily control registered fax, e-mail
and folders for each group.
To group destinations, the groups
must be registered beforehand.
Note
❒ You can register up to 500 groups.
❒ When using Scan to Folder function, you cannot send scan files to a
group with over 50 folders registered.
❒ You can set a protection code to
prevent unauthorized access to the
folders registered in a group. For
details, see p.63 “Address Book:
Program/Change/Delete Transfer
Request”.
Registering a New Group
A Press the {User Tools/Counter}} key.
B Press [System Settings].
D Press [Address Book: Program/Change/
Delete Group].
E Press [New Program].
F Press [Change] under
Group
Name.
4
G Enter the group name, and then
press [OK].
The Key Display name sets automatically.
Reference
p.143 “Entering Text”
H Press the title key under Select Title, if necessary.
Note
❒ The keys you can select are as
follows:
• [Freq.]… Added to the page
that is displayed first.
• [AB], [CD], [EF], [GH], [IJK],
[LMN], [OPQ], [RST],
[UVW], [XYZ], [1] to [10]…
Added to the list of items in
the selected title.
❒ You can select [Freq.] and one
more page for each title.
I When you want to change the key
C Press [Key Operator Tools], and then
press [T
TNext].
display, press [Change] under Key
Display. Enter the key display,
and then press [OK].
J Press [OK].
95
RussianC3_ENgsg-F_FM.book Page 96 Monday, June 16, 2003 6:48 PM
User Tools (System Settings)
4
Registering Destinations to a
Group
Removing a Destination from a
Group
You can register destinations to a
group.
When registering new destinations,
you can also register groups at the
same time.
A Press the {User Tools/Counter}} key.
B Press [System Settings].
C Press [Key Operator Tools], and then
A Press the {User Tools/Counter}} key.
B Press [System Settings].
C Press [Key Operator Tools], and then
D Press [Address Book Management].
E Select the user (destination) to re-
press [T
TNext].
D Press [Address Book Management].
E Select the user (destination) to
register in a group.
Press the user (destination) key, or
enter the registered number using
the number keys.
Note
❒ If you press , you can search
for a user by user name/index,
user code, fax destination, or email address.
F Press [Group].
G Select a group to which you want
to register the destinations.
Note
❒ If you press , you can search
for a group by entering the
group name.
H Press [OK].
96
press [T
TNext].
move from a group.
Press the user (destination) key, or
enter the registered number using
the number keys.
F Press [Group].
G Press the highlighted group key.
H Press [OK].
RussianC3_ENgsg-F_FM.book Page 97 Monday, June 16, 2003 6:48 PM
Registering Destinations to a Group
Displaying Destinations
Registered in Groups
You can check the user (destination)
of each group.
A Press the {User Tools/Counter}} key.
B Press [System Settings].
C Press [Key Operator Tools], and then
press [T
TNext].
D Press [Address Book: Program/Change/
Delete Group].
E Select the group where the data
you want to check is registered.
F Press [Programed Users].
All the user (destination) names
appear.
G Press [OK].
Changing a Group Name
A Press the {User Tools/Counter}} key.
B Press [System Settings].
C Press [Key Operator Tools], and then
press [T
TNext].
D Press [Address Book: Program/Change/
Delete Group].
E Press the group key you want to
change.
4
F Enter the items.
To change the group name and
key display
A Press [Change] under Group
Name or Key Display.
B Enter the new group name or
key display, and then press
[OK].
To change the title
A Press the title key under Select
Title.
To change the registration
number
A Press [Change] under Registration No..
B Enter the new registration number using the number keys.
C Press [#].
G Press [OK].
97
RussianC3_ENgsg-F_FM.book Page 98 Monday, June 16, 2003 6:48 PM
User Tools (System Settings)
Deleting a Group
A Press the {User Tools/Counter}} key.
B Press [System Settings].
C Press [Key Operator Tools], and then
press [T
TNext].
D Press [Address Book: Program/Change/
Delete Group].
E Press [Delete].
F Press a group key you want to de-
4
lete.
G Press [Yes].
98
RussianC3_ENgsg-F_FM.book Page 99 Monday, June 16, 2003 6:48 PM
Registering the Transfer Request
Registering the Transfer Request
This section describes how to register
the Transfer Station and Receiving
Station used in the fax function's
Transfer Request.
Note
❒ Before you can use Transfer Request, you must program the Polling ID and set the Transfer Report.
S e e “P ro g ra m m i n g a P o l lin g
ID”and “Transfer Report”, Facsimile Reference <Advanced Features>.
❖ Transfer Station
This is the machine that receives
the Transfer Request to forward incoming messages to another destination.
Note
❒ Polling ID's of the Requesting Party (this machine) and Transfer Stations must be identical.
❒ You can have up to 30 Receiving
Stations per Transfer Station. If
you specify a Transfer Station
Group, the Group counts as a single receiver.
4
Registering a Transfer
Station/Receiving Station
A Press the {User Tools/Counter}} key.
❖ Receiving Station
The facsimile or computer that receives messages from the Transfer
Station.
Limitation
❒ When messages are transferred by
fax, Transfer Stations must be machines of the same make as this,
and have the Transfer Station function.
❒ When messages are transferred by
e-mail, Transfer Stations must be
machines of the same make as this,
and have both the Transfer Station
and Internet Fax functions.
❒ You cannot use Transfer Request
without programming the fax
number or e-mail address of the
Requesting Party in the Address
Book (Quick Dial or Speed Dial) of
the Transfer Stations.
B Press [System Settings].
C Press [Key Operator Tools], and then
press [T
TNext].
D Press [Address Book: Program/Change/
Delete Transfer Request].
E Press [New Program].
F Set the Transfer Request's information.
99
RussianC3_ENgsg-F_FM.book Page 100 Monday, June 16, 2003 6:48 PM
User Tools (System Settings)
To register the Transfer Request
name and key display
A Press [Change] under Transfer
Request Name or Key Display.
The user (destination) name or
key display entry display appears.
B Enter the Transfer Request
name or key display, and then
press [OK].
Reference
p.143 “Entering Text”
4
To select the title
A To associate a Transfer Request name with a title, press
the title key under Select Title.
Note
❒ The keys you can select are as
follows:
• [Freq.]… Added to the
page that is displayed first.
• [AB], [CD], [EF], [GH],
[ I J K ] , [ L MN ] , [ O P Q ] ,
[RST], [UVW], [XYZ], [1] to
[10]… Added to the list of
items in the selected title.
❒ You can select [Freq.] and one
more page for each title.
G Press [Fax].
H Enter the items. See steps H and I
on p.77 “Registering a Fax Destination”.
100
I Press [E-mail].
J Enter the items. See steps H and I
on p.82 “Registering an E-mail
Destination”.
K Press [Receiving Station].
L Specify the Receiving Stations.
Note
❒ When specifying the Receiving
Stations, use the numbers
stored in Quick Dial keys,
Speed Dials or Groups in the
Transfer Station.
Quick Dial
A Press [q
qQuick Dial].
B Enter the number stored in the
Quick Dial of the Transfer Station using the number keys.
For example, to select the destination stored in Quick Dial 01 of
th e Trans fer St ation , ent er
{0}
}{1}
}.
C To specify an additional Receiving Station, press [Add].
Speed Dial
A Press [q
qpSpeed Dial].
B Enter the Speed Dial using the
number keys.
For example, to select the destination stored in Speed Dial 12 of
th e Trans fer St ation , ent er
{1}
}{2}
}.
C To specify an additional Receiving Station, press [Add].
RussianC3_ENgsg-F_FM.book Page 101 Monday, June 16, 2003 6:48 PM
Registering the Transfer Request
Group Dial
A Press [q
qppGroup Dial].
B Enter the Group number using
the number keys.
For example, to select the destinations stored in Group 04 of
th e Transfe r Stat ion, e nt er
{0}
}{4}
}.
C To specify an additional Receiving Station, press [Add].
To change the Transfer Request
name and key display
A Press [Change] under Transfer
Request Name or Key Display.
B Enter the new Transfer Request name or key display, and
then press [OK].
To change the title
M When you have specified all the
A Press the title key under Select
Title.
N Press [Exit].
To change the Transfer Station
4
Receiving Stations, press [OK].
Changing a Registered Transfer
Station/Receiving Station
A Press the {User Tools/Counter}} key.
B Press [System Settings].
C Press [Key Operator Tools], and then
press [T
TNext].
D Press [Address Book: Program/Change/
Delete Transfer Request].
E Select the registered Transfer Station/Receiving Station user you
want to change.
Press the user (destination) key, or
enter the registered number using
the number keys.
Note
❒ If you press , you can search
for a user by Transfer Request
name, fax destination, or e-mail
address.
F Enter the items.
A Press [Fax].
Proceed to step C when messages are transferred by e-mail.
B Change the Transfer Station's
information. See steps G and H
on p.79 “Changing a Registered Fax Destination”.
C Press [E-mail].
D Change the Transfer Station's
information. See steps G and H
on p.84 “Changing a Registered E-mail Destination”.
To change the Receiving Station
A Press [Receiving Station].
B Select the Receiving Station
you want to change.
C Press [Clear] to clear the number, and then enter the new
number us ing the number
keys.
G Press [OK].
H Press [Exit].
101
RussianC3_ENgsg-F_FM.book Page 102 Monday, June 16, 2003 6:48 PM
User Tools (System Settings)
Deleting a Registered Transfer
Station/Receiving Station
A Press the {User Tools/Counter}} key.
B Press [System Settings].
C Press [Key Operator Tools], and then
press [T
TNext].
D Press [Address Book: Program/Change/
Delete Transfer Request].
E Press [Delete].
F Select a Transfer
4
Request you
want to delete.
Press the Transfer Request key, or
enter the registered number using
the number keys.
G Press [Yes].
H Press [Exit].
102
RussianC3_ENgsg-F_FM.book Page 103 Monday, June 16, 2003 6:48 PM
Programming/Changing LDAP Server
Programming/Changing LDAP Server
Programming an LDAP server allows
you to look up e-mail destinations
from the LDAP server Address Book
directly. This function is available
when you send scan files by e-mail
using scanner function.
D Press [Program/Change LDAP Server].
E Enter the items.
Note
❒ Select [ON] in the Use LDAP Server
setting to use this function. See
p.66 “Use LDAP Server”.
A Press [Change] under Identification Name.
❒ This function supports LDAP Version 2 and 3.
❒ To ensure successful searching,
make sure the server name and
port number are entered correctly.
For details, ask your network administrator.
Programming an LDAP Server
A Press the {User Tools/Counter}} key.
To enter an identification name
4
B Enter the server's identification name.
C Press [OK].
To enter a server name
A Press [Change] under Server
Name.
B Enter the LDAP server name.
C Press [OK].
To enter the search base
A Press [Change] under Search
Base.
B Enter the search base.
B Press [System Settings].
C Press [Key Operator Tools], and then
press [T
TNext] twice.
Note
❒ For example, if you enter
“ou=sales department,
o=ABC”, searching will start
below the sales department
level of ABC company (here,
“ou” stands for organization
unit, and “o” stands for company).
C Press [OK].
103
RussianC3_ENgsg-F_FM.book Page 104 Monday, June 16, 2003 6:48 PM
User Tools (System Settings)
To enter a port number
A Press [Change] under Port No..
B Enter the port number using
the number keys, and then
press [#].
To set authentication
A Press [Next].
B Press [ON] or [High Security] under Authentication.
4
Note
❒ [High Security] is not available
with LDAP Version 2.
❒ When [ON] or [High Security]
is selected, the administrator
account name and password
is required to acc ess the
LDAP server.
❒ When [High Security] is selected, you can use a generic
password unique to the network. If you do this, the server also requires the same
setting. For details, ask your
network administrator.
104
To enter the user name and
password
Note
❒ To use the administrator account for authentication, enter
the account name and password
here.
❒ If you leave the user name and
password blank, users will be
prompted for the password every time they attempt to connect
to the LDAP server.
A Press [Next].
B Press [Change] under User
Name.
C Enter the user name, and then
press [OK].
D Press [Change] under Password.
E Enter the password, and then
press [OK].
To test the connection
A Press [Connection Test].
A connection test is carried
out.
B Press [Exit].
Note
❒ If the connection test fails,
check your settings, and
then try again.
RussianC3_ENgsg-F_FM.book Page 105 Monday, June 16, 2003 6:48 PM
Programming/Changing LDAP Server
To set search options
Changing an LDAP Server
Note
❒ You can search the LDAP server
data using keywords below:
Name, E-mail Address, Fax
Destination, Company Name,
Department Name. You can
specify an additional keyword.
This must be predefined in your
LDAP database.
A Press [Next] twice.
B Press [Change] under Attribute.
C Enter the attribute you want to
use for searching e-mail addresses, and then press [OK].
D Press [Change] under Key Display.
E Enter the attribute's display
name, and then press [OK].
A Press the {User Tools/Counter}} key.
B Press [System Settings].
C Press [Key Operator Tools], and then
Note
❒ For example, if you want to
sort e-mail addresses by employees' number, enter “employeeNo” in the Attribute
field, and “Employee No.” in
the Key Display field.
B Enter a new identification
name for the server.
C Press [OK].
F Press [OK].
G Press [Exit].
H Press the {User Tools/Counter}} key.
press [T
TNext] twice.
D Press [Program/Change LDAP Server].
E Change the items.
To change an identification name
4
A Press [Change] under Identification Name.
To change the server name
A Press [Change] under Server
Name.
B Enter the new LDAP server
name.
C Press [OK].
To change the search base
A Press [Change] under Search
Base.
B Enter the new search base.
C Press [OK].
105
RussianC3_ENgsg-F_FM.book Page 106 Monday, June 16, 2003 6:48 PM
User Tools (System Settings)
To change a port number
A Press [Change] under Port No..
B Enter the new port number using the number keys, and then
press [#].
To change authentication
A Press [Next].
B Select [ON] or [High Security] if
you want to activate authentication. Select [OFF] to cancel it.
4
Note
❒ [High Security] is not available
when the LDAP Version is 2.
❒ When [ON] or [High Security]
is selected, the administrator
account name and password
is required to acc ess the
LDAP server.
❒ When [High Security] is selected, you can use a generic
password unique to the network. If you do this, the server also requires the same
setting. For details, ask your
network administrator.
To change the user name and
password
A Press [Next].
B Press [Change] under User
Name.
C Enter the new user name, and
then press [OK].
D Press [Change] under Password.
E Enter the new password, and
then press [OK].
Note
❒ The user name and password
are of a user who is authorized to access the LDAP
server.
❒ You can press [Connection
Test] to check if the new settings work.
To change search options
A Press [Next] twice.
B Press [Change] under Attribute.
C Enter a new attribute, and then
press [OK].
D Press [Change] under Key Display.
E Enter the attribute's new display name, and then press [OK].
F Press [OK].
G Press [Exit].
H Press the {User Tools/Counter}} key.
106
RussianC3_ENgsg-F_FM.book Page 107 Monday, June 16, 2003 6:48 PM
5. Troubleshooting
If Your Machine Does Not Operate As You
Want
The following chart gives explanations of common problems and messages. If
other messages appear, follow the instructions displayed.
Note
❒ If you cannot make copies as you want because of the paper type, paper size
or paper capacity problems, use recommended paper. See p.163 “Copy Paper”.
General
Problem
Causes
“Please wait. ” appears
Wait for the machine to get ready.
This message appears
when you turn on the operation switch or change the
toner bottle.
Solutions
The display is off.
The screen contrast knob is Set the screen contrast knob to the
turned to the dark position. light position to see the display panel properly.
The machine is in Energy
Saver mode.
} key to canPress the {Energy Saver}
cel Energy Saver mode.
The operation switch is
turned off.
Turn on the operation switch.
Nothing happens when the
operation switch is turned
on.
The main power switch is
turned off.
Turn on the main power switch.
Memory is full.
There are too many
scanned pages or stored
files: hard disk capacity is
exceeded.
Press [Delete File] to delete unnecessary documents.
The function status indicator is red.
The function associated
with the red indicator was
interrupted.
Press the function key corresponding to the indicator. Follow the instructions that appear on the control
panel.
The user code entry display appears.
Users are restricted by user
management.
Enter the user code (up to 8 digits),
and then press [#].
107
RussianC3_ENgsg-F_FM.book Page 108 Monday, June 16, 2003 6:48 PM
Troubleshooting
Problem
Causes
The main power indicator continues
blinking and does
not turn off when
pressed.
This occurs in the fol- Close the exposure glass cover or ADF, and
lowing cases:
check if the machine communicating with a
computer.
• The exposure
Solutions
glass cover or the
ADF is open.
• The machine is
communicating
with external
equipment.
• The hard disk is
active.
5
Original images are
printed on the reverse side of the paper.
You may have loaded the paper incorrectly.
Load paper correctly. Load paper into Tray 1-4
with the print side up, and into the LCT or bypass tray with the print side down. See p.112
“Orientation-Fixed Paper or Two-Sided Paper”.
Misfeeds occur frequently.
The tray's side
guides may not be
locked.
Check the side guides are locked. See p.122
“Changing the Paper Size”.
The tray's end guide
may not be set properly.
Check the end guide is set properly. See p.122
“Changing the Paper Size”.
You may have loaded paper of a size not
shown on the paper
size selector.
When using paper of a size that cannot be detected automatically, use Tray Paper Settings to
set the paper size. See p.55 “Tray Paper Size:
Tray 1–4” and p.163 “Copy Paper”.
An error message re- When a misfeed mes- Clear misfed paper, and then open and close the
mains, even if misfed sage appears, it refront cover. See p.116 “x Clearing Misfeeds”.
paper is removed.
mains until you open
and close the cover,
as required.
An error message re- This may occur if the Press the {Start}
} key.
mains, even if conHDD is not installed.
sumables are
replaced and/or misfed paper is removed.
Cannot print in duplex mode.
You forgot your key
operator code
108
You cannot use paper in the bypass tray
for duplex printing.
For duplex printing, select Tray 1-4 in copier
mode or with the printer driver.
[1 Sided Copy] is selected for Paper
Type: Tray 1-4.
Select [2 Sided Copy] for Paper Type: Tray 1-4. See
p.56 “Paper Type: Tray 1–4”
—
Contact your service representative.
RussianC3_ENgsg-F_FM.book Page 109 Monday, June 16, 2003 6:48 PM
If Your Machine Does Not Operate As You Want
Document Server
Problem
Solutions
"Scanned pages exceeded
max. number. Do you want
to store the scanned pages as a file?" appears.
The number of scanned pages exceeds the capacity per
file of the Document Server.
You forgot your password.
You can temporarily access password-protected files.
To store scanned pages as a file, press [Store File].
Scanned data is stored as a file in the Document Server.
If you do not want to store scanned pages, press [No].
Scanned data is deleted.
Press [Unlock] in Password Management for Stored Files
in User Tools. See p.147 “Temporarily Disabling Document Security” .
You can delete all stored documents at once with User
Tools. See p.66 “Delete All Files” .
Make sure no important documents are stored in the
Document Server before deleting all stored documents.
5
You cannot find out what is stored in Check the date or time column in the Document Server:
a file.
Select Files to Print display.
Check document content by printing it's first page. Press
the line of the document in the Document Server: Select
Files to Print display, and then press [Print 1st Page] followed by the {Start}
} key.
Memory frequently becomes full.
• Press [Delete File] to delete selected documents to increase available memory.
• Delete documents stored using the scanner function.
See Scanner Reference.
You want to check print quality before making a large print run.
Check print quality by printing out only the first set using the {Sample Copy}
} key.
The copier or scanner function is in use. To cancel a job
"Original is being
scanned by another func- in progress, first press [Exit], and then press the {Copy}}
key or {Scanner}
} key. Next, press the {Clear/Stop}
} key.
tion." appears.
When the message "[Stop] key was
pressed.Stop printing?" appears, press [Stop].
109
RussianC3_ENgsg-F_FM.book Page 110 Monday, June 16, 2003 6:48 PM
Troubleshooting
B Loading Paper
Reference
For paper types and sizes, see
p.163 “Copy Paper”.
Loading Paper into Paper
Trays
Setting special paper in the paper
tray 2
A Load the special paper below
the limit mark of the tray.
Note
❒ You can change the paper size, see
p.122 “Changing the Paper Size”.
A Pull
out the paper tray until it
stops.
5
B Square the paper and load it in
the tray with the copying face up.
Note
❒ Fan the paper before loading.
❒ When using paper such as
translucent paper, straighten
curled or warped paper before loading.
C Push
stops.
Important
❒ If you add paper to a paper tray
with paper left inside, a misfeed
might occur.
❒ Do not stack paper over the limit mark.
❒ When loading small quantities
of paper, be careful n ot to
squeeze the side guide in too
tightly, as the paper will not
feed properly.
110
the paper tray in until it
RussianC3_ENgsg-F_FM.book Page 111 Monday, June 16, 2003 6:48 PM
B Loading Paper
Loading Paper into Large
Capacity Tray (optional)
Note
❒ Load copy paper of the same size
and orientation in both left and
right side trays.
Note
❒ Fan the paper before loading.
❒ Straighten curled or warped paper before loading.
C Push
the paper tray in until it
stops.
A Pull out the LCT.
5
B Square the paper, and then load it
in the tray with the copying face
up.
Important
❒ Align the right edge of the right
copy paper stack with the right
edge of the tray.
❒ Align the left edge of the left
copy paper stack with the left
edge of the tray.
❒ Do not stack paper over the limit mark.
111
RussianC3_ENgsg-F_FM.book Page 112 Monday, June 16, 2003 6:48 PM
Troubleshooting
Orientation-Fixed Paper or Two-Sided Paper
Orientation-fixed (top to bottom) or two-sided paper (for example, letterhead
paper, punched paper, or copied paper) might not print correctly, depending on
how the originals and paper are placed. Select [Yes] in Letterhead Setting under
Copier/Document Server Features, and then place the original and paper as
shown below (see Copy Reference). When printing with the printer function, placing orientation is the same.
LCT
ADF
5
112
RussianC3_ENgsg-F_FM.book Page 113 Monday, June 16, 2003 6:48 PM
D Adding Toner
D Adding Toner
When D appears, it is time to add toner.
R WARNING:
• Do not incinerate used toner or toner containers. Toner dust might ignite when exposed to an open flame. Dispose of used toner containers
in accordance with local regulations.
R CAUTION:
• Keep toner (used or unused) and toner containers out of reach of children.
Important
❒ Fault may occur if you use toner other than the recommended type.
❒ When adding toner, do not turn off the operation switch. If you do, settings
will be lost.
❒ Always add toner when the machine instructs you.
❒ Do not repeatedly install and remove toner bottles. This will result in toner
leakage.
❒ Do not shake the removed toner bottle. Remaining toner might scatter.
5
Note
❒ You can make about 50 copies even after the “DToner is almost empty.”and “Replace Toner Bottle.” messages appear, but replace toner early to prevent poor copy quality.
Reference
For details about toner storage, see p.132 “Toner Storage”.
113
RussianC3_ENgsg-F_FM.book Page 114 Monday, June 16, 2003 6:48 PM
Troubleshooting
Removing Toner
• 1: Open the front cover of the machine.
• 2: Lift the green lever.
• 3: Push the green lever, and then gently
pull out the holder.
5
SL
OW
• 4: Push the toner bottle back to raise its top,
and then gently pull out the bottle.
114
RussianC3_ENgsg-F_FM.book Page 115 Monday, June 16, 2003 6:48 PM
Inserting Toner
Inserting Toner
• 1: Hold the new bottle horizontally and
shake it from side to side five or six times.
Note
❒ Do not remove the black cap before
shaking.
• 2: Remove the black cap.
Note
❒ Do not remove the inner cap.
• 3: Put the toner bottle on the holder, and
then pull its top forward.
5
• 4: Push in the green lever until it clicks.
OW
SL
• 5: Press down the green lever.
• 6: Close the machine's front cover.
115
RussianC3_ENgsg-F_FM.book Page 116 Monday, June 16, 2003 6:48 PM
Troubleshooting
x Clearing Misfeeds
R CAUTION:
• The fusing section of this machine might be very hot. Caution should be taken when removing misfed paper.
Important
❒ When clearing misfeeds, do not turn off the operation switch. If you do, your
copy settings will be lost.
❒ To prevent misfeeds, do not leave any torn scraps of paper inside the machine.
❒ If paper misfeeds occur frequently, contact your service representative.
Note
❒ More than one misfed area may be indicated. When this happens, check all
the areas indicated. See the following charts: A, B, C, D, P, R, Y, Z
❒ Inside the finisher, or inside the front cover, there is a sticker explaining how
to remove misfed paper.
5
116
RussianC3_ENgsg-F_FM.book Page 117 Monday, June 16, 2003 6:48 PM
x Clearing Misfeeds
5
117
RussianC3_ENgsg-F_FM.book Page 118 Monday, June 16, 2003 6:48 PM
Troubleshooting
5
118
RussianC3_ENgsg-F_FM.book Page 119 Monday, June 16, 2003 6:48 PM
x Clearing Misfeeds
5
ZLFX260E
119
RussianC3_ENgsg-F_FM.book Page 120 Monday, June 16, 2003 6:48 PM
Troubleshooting
5
120
RussianC3_ENgsg-F_FM.book Page 121 Monday, June 16, 2003 6:48 PM
x Clearing Misfeeds
5
ZLFX270E
121
RussianC3_ENgsg-F_FM.book Page 122 Monday, June 16, 2003 6:48 PM
Troubleshooting
Changing the Paper Size
Preparation
Be sure to select the paper size
with User Tools and the paper size
selector. If you do not, misfeeds
might occur. See p.55 “Tray Paper
Size: Tray 1–4”.
D Release the side lever.
Important
❒ If you want to change the paper
size set in the LCT, contact your
service representative.
Reference
For details about paper sizes and
types, see p.163 “Copy Paper”.
5
E While pressing the release lever,
adjust the side guides.
Changing the Paper Size of the
Paper Tray
A Make sure the paper tray is not in
use. Then, pull the paper tray out
slowly.
B If paper is loaded in the tray, remove it.
C While pressing the release lever,
F Square the paper, and then load it
in the tray with the copying face
up.
adjust the back guide.
Important
❒ Do not stack paper over the limit mark.
❒ Make sure the paper stack is
flush against the right side
guide.
122
RussianC3_ENgsg-F_FM.book Page 123 Monday, June 16, 2003 6:48 PM
Changing the Paper Size
Note
❒ Fan the paper before loading.
❒ Straighten curled or warped paper before loading.
I While pressing the release lever,
adjust the back guide to the new
paper size.
G While pressing the release lever,
adjust the side guides to the new
paper size.
J Adjust the paper size selector to
the new paper size.
5
Important
❒ When loading small quantities
of paper, be careful n ot to
squeeze the side guide in too
tightly, as the paper will not
feed properly.
H Lock the side lever.
To adjust the paper size to a size
not indicated on the paper size
selector
A Set the paper size selector to
the p mark.
B Press the {User Tools/Counter}
}
key.
C Press [System Settings].
D Press [Tray Paper Settings].
E Press [Tray Paper Size: Tray 1],
[Tray Paper Size: Tray 2], [Tray Paper Size: Tray 3] or [Tray Paper
Size: Tray 4].
F Select the required size, and
then press [OK].
123
RussianC3_ENgsg-F_FM.book Page 124 Monday, June 16, 2003 6:48 PM
Troubleshooting
G Press [Exit] or the {User Tools/
Counter}
} key to exit User Tools.
Reference
p.55 “Tray Paper Size: Tray
1–4”
K Gently push the paper tray in until it stops.
L Check
the paper size shown on
the display panel.
5
124
RussianC3_ENgsg-F_FM.book Page 125 Monday, June 16, 2003 6:48 PM
d Adding Staples
d Adding Staples
Important
❒ Stapling failures or jams may occur if you use a staple cartridge other than
that recommended.
Reference
For details about the type of finisher, see p.19 “External Options”.
500-Sheet Finisher
• 1: Open the side cover.
5
• 2: Remove the cartridge.
• 3: Take out the empty refill in the direction
of the arrow.
• 4: Push in the new refill until it clicks.
• 5: Pull out the ribbon.
125
RussianC3_ENgsg-F_FM.book Page 126 Monday, June 16, 2003 6:48 PM
Troubleshooting
• 6: Reinstall the cartridge.
• 7: Close the side cover.
1000-Sheet Finisher
• 1: Open the front cover of the finisher, and
then pull out the staple unit.
5
ZGJS801E
• 2: Hold the green lever, and then gently
pull out the cartridge.
ZGJS802E
• 3: Hold both sides of the cartridge.
• 4: Pull up the upper unit of the cartridge.
ZGJS803E
• 5: Take out the empty refill in the arrow direction.
ZGJS804E
126
RussianC3_ENgsg-F_FM.book Page 127 Monday, June 16, 2003 6:48 PM
d Adding Staples
• 6: Align the arrows on the new refill with
those on the cartridge, and then push in the
refill until it clicks.
ZGJS805E
• 7: Gently push down the upper unit into
the cartridge.
ZGJS806E
• 8: Pull out the ribbon.
5
ZGJS807E
• 9: Hold the green lever while pushing in
the cartridge until it clicks.
• 10: Push back the staple unit, and then
close the front cover of the finisher.
ZGJS808E
127
RussianC3_ENgsg-F_FM.book Page 128 Monday, June 16, 2003 6:48 PM
Troubleshooting
Removing Jammed Staples
Note
❒ Curled paper may cause staples to jam. To avoid this, turn copy paper over
in the tray. If there is no improvement, change to a stiffer copy paper.
❒ When the 500-sheet finisher is installed, after removing jammed staples, staples will not be ejected the first few times you try to use the stapler.
Reference
For types of finisher, see p.19 “External Options”.
500-Sheet Finisher
• 1: Open the side cover.
5
• 2: Remove the cartridge.
• 3: Open the face plate.
• 4: Remove the jammed staples.
• 5: Reinstall the cartridge.
• 6: Close the side cover.
128
RussianC3_ENgsg-F_FM.book Page 129 Monday, June 16, 2003 6:48 PM
Removing Jammed Staples
1000-Sheet Finisher
• 1: Open the front cover of the finisher, and
then pull out the staple unit.
ZGJS801E
• 2: Hold the green lever while gently pulling out the cartridge.
5
ZGJS802E
• 3: Open the cartridge's face plate.
ZGJS813E
• 4: Remove any jammed staples.
ZGJS814E
• 5: Pull down the cartridge's face plate until
it clicks.
ZGJS815E
• 6: Hold the green lever while pushing in
the cartridge until it clicks.
• 7: Push back the staple unit, and then close
the front cover of the finisher.
ZGJS864E
129
RussianC3_ENgsg-F_FM.book Page 130 Monday, June 16, 2003 6:48 PM
Troubleshooting
5
130
RussianC3_ENgsg-F_FM.book Page 131 Monday, June 16, 2003 6:48 PM
6. Remarks
Dos and Don'ts
R CAUTION:
• Unplug the power cord from the
wall outlet before you move the
machine. While moving the machine, you should take care that
the power cord will not be damaged under the machine.
Important
❒ Do not turn the power off while
the On indicator is lit or blinking.
Doing so may damage the hard
disk.
❒ Before unplugging the power cord
or turning off the main power
sw itc h, m ake sure remaining
m e m ory space is at 100% , a s
shown on the display. See p.25
“Turning Off the Power” and p.25
“Turning Off the Main Power”.
• When you use this machine for a
long time in a confined space without good ventilation, you may detect an odd smell. To keep the
workplace comfortable, we recommend that you keep it well ventilated.
• Do not touch areas on or around
the fusing unit. These areas get hot.
• After making copies continuously,
the exposure glass may become
warm—this is not a malfunction.
• The area around the ventilation
hole might feel warm. This is
caused by exhaust air and is not a
malfunction.
• When the machine is not in use
and in stand-by mode, you may
hear a small noise inside. This is
caused by the image stabilization
process and is not a malfunction.
• Do not turn off the operation
switch while copying or printing.
Make sure all copying or printing
has finished first.
• The machine might not produce
good copy images if condensation
forms inside as a result of rapid
temperature change.
• Do not open the covers of the machine while copying or printing. If
you do, misfeeds might occur.
• Do not move the machine during
copying or printing.
• If you operate the machine improperly or a machine failure occurs, settings might be lost. Be sure
to make a note of your machine
settings.
• The supplier shall not be liable for
any loss or damage resulting from
mechanical failure, loss of settings,
or use of the machine.
131
RussianC3_ENgsg-F_FM.book Page 132 Monday, June 16, 2003 6:48 PM
Remarks
Toner
Handling Toner
R WARNING:
• Do not incinerate used toner or toner containers. Toner dust might ignite when exposed to an open flame. Dispose of used toner containers
in accordance with local regulations.
R CAUTION:
• Keep toner (used or unused) and toner containers out of reach of children.
Important
❒ Fault may occur if you use toner other than the recommended type.
Reference
To add toner, see p.113 “D Adding Toner”.
6
Toner Storage
When storing toner, the following precautions should always be followed:
• Store toner containers in a cool, dry place free from direct sunlight.
• Store on a flat surface.
Used Toner
Note
❒ Toner cannot be re-used.
132
RussianC3_ENgsg-F_FM.book Page 133 Monday, June 16, 2003 6:48 PM
Where to Put Your Machine
Where to Put Your Machine
Machine Environment
Environments to avoid
Choose your machine's location carefully. Environmental conditions
greatly affect its performance.
• Locations exposed to direct sunlight or other sources of strong
light (more than 1,500 lux).
• Locations directly exposed to cool
air from an air conditioner or heated air from a heater. (Sudden temperature changes can cause
condensation to form inside the
machine.)
• Locations close to machines generating ammonia, such as a diazo
copy machine.
• Places where the machine will be
subject to frequent strong vibration.
• Dusty areas.
• Areas with corrosive gases.
Optimum environmental conditions
R CAUTION:
• Keep the machine away from humidity and dust. Otherwise a fire
or an electric shock might occur.
• Do not place the machine on an
unstable or tilted surface. If it topples over, an injury might occur.
R CAUTION:
• If you use the machine in a confined space, make sure there is a
continuous air turnover.
6
• Temperature: 10-32 °C (50-89.6 °F)
(humidity to be 54% at 32 °C, 89.6
°F)
• Humidity: 15-80% (temperature to
be 27 °C, 80.6 °F at 80%)
• A strong and level base.
• The machine must be level within
5 mm, 0.2 inches: both front to rear
and left to right.
• To avoid possible buildup of
ozone, be sure to locate this machine in a large well ventilated
room that has an air turnover of
more than 30 m3/hr/person.
133
RussianC3_ENgsg-F_FM.book Page 134 Monday, June 16, 2003 6:48 PM
Remarks
6
134
Moving
Power Connection
R CAUTION:
• Unplug the power cord from the
wall outlet before you move the
machine. While moving the machine, you should take care that
the power cord will not be damaged under the machine.
R WARNING:
• Connect the machine only to
the power source described on
the inside front cover of this
manual. Connect the power
cord directly into a wall outlet
and do not use an extension
cord.
Important
❒ Be careful when moving the machine. Take the following precautions:
• Turn off the main power. See
p.25 “Turning Off the Main
Power”.
• Unplug the power cord from
the wall outlet. When you pull
out the plug from the socket,
grip the plug to avoid damaging the cord, thereby reducing
the risk of fire or electric shock.
• Close all covers and trays, including the front cover and bypass tray.
❒ Move the machine carefully. If you
do not, it could be damaged and
stored files might be lost.
❒ Do not take off the holding stand.
❒ Protect the machine from strong
shocks. Impact can damage the
hard disk and cause stored files to
be lost. As a precautionary measure, files should be copied to another computer.
• Do not damage, break or make
any modifications to the power
cord. Do not place heavy objects on it. Do not pull it hard
nor bend it more than necessary. These actions could
cause an electric shock or fire.
R CAUTION:
• Unplug the power cord from the
wall outlet before you move the
machine. While moving the machine, you should take care that
the power cord will not be damaged under the machine.
R CAUTION:
• When you disconnect the power
plug from the wall outlet, always
pull the plug (not the cable).
• When the main power switch is in
the stand-by position, the optional
anti-condensation heaters are on.
In an emergency, unplug the machine's power cord.
• When you unplug the power cord,
the anti-condensation heaters turn
off.
• Make sure the plug is inserted
firmly in the wall outlet.
• Voltage must not fluctuate by
more than 10%.
• The wall outlet shall be installed
near the machine and shall be easily accessible.
RussianC3_ENgsg-F_FM.book Page 135 Monday, June 16, 2003 6:48 PM
Where to Put Your Machine
Access to the Machine
Place the machine near the power
source, providing the clearance areas
shown.
1
2
4
3
1. Rear: more than 1 cm (4")
2. Right: more than 1 cm (4")
3. Front: more than 75 cm (29.6")
4. Left: more than 1 cm (4")
6
Note
❒ For the required space when options are installed, contact your
service representative.
135
RussianC3_ENgsg-F_FM.book Page 136 Monday, June 16, 2003 6:48 PM
Remarks
Maintaining Your Machine
If the exposure glass, exposure glass
cover, or ADF belt is dirty, copy clarity may be reduced. Clean these parts
if they are dirty.
Cleaning the Exposure Glass
Cover
❖ Cleaning the machine
Wipe the machine with a soft,
damp cloth, and then wipe it with
a dry cloth to remove the water.
Important
❒ Do not use chemical cleaners or organic solvents, such as thinner or
benzene. If such substances get inside the machine or melt plastic
parts, a failure might occur.
❒ Do not clean parts other than those
explicitly specified in this manual.
Other parts should only be cleaned
by your service representative.
6
ZGJS826E
Cleaning the Auto Document
Feeder
Cleaning the Exposure Glass
GDSH130J
Clean 1 and 2.
GDSH050J
Clean 1 and 2.
136
RussianC3_ENgsg-F_FM.book Page 137 Monday, June 16, 2003 6:48 PM
Replacing the Photo Conductor Unit (PCU)
Replacing the Photo Conductor Unit (PCU)
When the “Replace photoconductor
unit” message appears on the display
panel, it is time to replace the PCU
panel.
A If
the duplex unit is installed,
open it by pushing up the catch.
R WARNING:
• Do not incinerate the photoconductor unit. Toner dust
might ignite when exposed to
an open flame. Dispose of the
used photoconductor unit in
accordance with local regulations.
Important
❒ Do not tilt the used PCU after taking it out of the machine. If you do,
toner might leak out.
❒ Do not hold the developer cartridge while taking out the used
PCU. If you do, the cartridge might
unlock and fall.
❒ Do not touch the PCU. If you do,
copy quality might be reduced.
❒ Before you take out the used PCU,
wait until the machine has completely stopped and is making no
sound. Not taking this precaution
could result in a fault.
❒ If there are misfeeds, remove the
misfed paper before taking out the
used PCU.
❒ Be sure to remove the sealing tape
before installing the new PCU.
Leaving it attached could result in
a fault.
❒ After installing the new PCU, the
machine takes about one minute to
initialize. During this period, do
not open the front cover or turn off
the main power switch. If you do,
a fault might occur.
B Open
the machine's right cover
by pushing up the catch.
6
C Open the front cover.
137
RussianC3_ENgsg-F_FM.book Page 138 Monday, June 16, 2003 6:48 PM
Remarks
D While pressing the button, slide
out the PCU, until it stops.
G Put the old PCU (removed in step
E) into the plastic bag from step F,
keeping it at the same angle as it
was when installed. Then, zip up
the plastic bag.
Note
❒ Do not tilt the used PCU after
taking it out of the machine. If
you do, toner might leak out.
H Remove the two red sheets from
the PCU in the order shown.
E Raise the green handle and slide
out the PCU toward you.
6
Important
❒ Do not tilt or drop the removed
PCU. Moving it suddenly can
cause toner leakage.
❒ Do not change the toner when
there is no PCU installed.
F Take the new PCU from the box
and, while holding the handle, remove the plastic bag.
Important
❒ Do not drop or mishandle the
removed PCU.
❒ Do not touch the side of the
PCU.
138
Important
❒ Remove the PCU keeping it level as shown. Otherwise, the toner inside might leak out.
❒ After removing the black protection sheet, do not touch the
inside of the unit or the green
parts.
I Align the new PCU with the rail
inside the machine. Slide the unit
all the way in.
RussianC3_ENgsg-F_FM.book Page 139 Monday, June 16, 2003 6:48 PM
Replacing the Photo Conductor Unit (PCU)
J Push
the unit into the machine
until it clicks into place.
K Remove
the red sheet from the
PCU, and then remove the two
strips of tape.
M Close the front cover.
N If
the duplex unit is installed,
close it by pushing up the catch.
6
L Close the machine's right cover.
Note
❒ Check the "Replace PCU" message does not appear on the display panel.
Note
❒ If you cannot close the machine's right cover, the PCU is
not installed properly. Slide the
PCU out and push it in again
until it clicks into place.
139
RussianC3_ENgsg-F_FM.book Page 140 Monday, June 16, 2003 6:48 PM
Remarks
Other Functions
Inquiry
The inquiry function lets you check
the telephone numbers to contact for
repairs or ordering toner. Be sure to
contact your service engineer to verify the following:
❖ Consumables
• Telephone No. to order
• Toner
• Staple
• TX Stamp Name
❖ Machine Maintenance/Repair
• Telephone No.
• Serial No. of Machine
6
❖ Sales Representative
• Telephone No.
A Press the {User Tools/Counter}} key.
B Press [Inquiry].
Printing inquiry information
A Press [Print Inquiry List].
B Press the {Start}
} key.
Inquiry information is printed.
C Press [Exit].
D Press [Exit].
Changing the Display Language
You can change the language used on
the display. English is set as default.
A Press the {User Tools/Counter}} key.
B Press [Español].
The language is changed to Spanish.
Inquiry information appears.
C Press [Exit].
The menu appears in Spanish.
140
RussianC3_ENgsg-F_FM.book Page 141 Monday, June 16, 2003 6:48 PM
Counter
Counter
Displaying the Total Counter
You can display the total counter value used for all functions.
A Press the {User Tools/Counter}} key.
B Press [Counter].
6
C To print a counter list, press [Print
Counter List].
D Press the {Start}} key.
A counter list prints out.
141
RussianC3_ENgsg-F_FM.book Page 142 Monday, June 16, 2003 6:48 PM
Remarks
6
142
RussianC3_ENgsg-F_FM.book Page 143 Monday, June 16, 2003 6:48 PM
7. Entering Text
Entering Text
This section describes how to enter characters. When you enter a character, it appears at the position of the cursor. If there is a character already at the cursor position, the entered character appears before that.
Available Characters
• Alphabetic characters
ABCDEFGHIJKLMNOPQRSTUVWXYZabcdefghijklmnopqrstuvwxyz
• Symbols
• Numerals
0123456789
Keys
ZHWS030E
Note
❒ When entering uppercase or lowercase letters continuously, use [Shift Lock] to
lock the case.
143
RussianC3_ENgsg-F_FM.book Page 144 Monday, June 16, 2003 6:48 PM
Entering Text
How to Enter Text
Entering letters
A Press [Shift] to switch between uppercase and lowercase.
B Press the letters you want to enter.
Deleting characters
A Press [Backspace] or [Delete All] to delete characters.
7
144
RussianC3_ENgsg-F_FM.book Page 145 Monday, June 16, 2003 6:48 PM
8. Security
Security
Confidential information is always at risk of being copied without permission or
subject to unauthorized access through the network. To protect documents from
such intrusion, not only can passwords be set, but also the Extended Security
function can be used to strengthen security.
For those who require increased document protection, we recommend using the
Extended Security function.
Primary Security Functions
❖ Protecting Stored Documents
Protects documents with a password when using Document Server or Locked
Print. Furthermore, the Extended Security function can protect against password-generating cracking. See p.145 “Extended Security Function”.
❖ Protecting Image Data Remaining in Memory
Protects image data remaining in memory. When a copy or print job is completed, or a job is canceled, the data is secure.
❖ Protecting against Unauthorized Access Via Phone Line
Accepts only facsimile calls.
❖ Authenticating Administrator
Protects essential functions for administrating document security using an access code. See p.60 “Key Operator Code”.
Extended Security Function
By setting a password, document operations such as printing, deleting, or delivering can be restricted to authorized users and denied to others. However, passwords can be cracked. When the Extended Security function is used, entering the
wrong password 10 times will lock that document, protecting it from unauthorized access.
To unlock documents, see p.147 “Unlocking a locked document”.
Documents that can be protected by the Extended Security function are as follows (all documents must be set with a password to be protected using this function):
145
RussianC3_ENgsg-F_FM.book Page 146 Monday, June 16, 2003 6:48 PM
Security
❖ Documents stored in the Document Server by the following functions
• Document Server
• Copier function
• Fax transmission
• Scanner function
• Printer driver
❖ Documents stored from the printer driver using the Locked Print function
Reference
For information about Document Server, see p.33 “Document Server”.
For information about Locked Print, see “Locked Print”, Printer Reference,
or the printer driver Help.
Note
❒ Once a document is locked, it will reject the correct password until it is unlocked.
❒ When the Extended Security function is on, delivery server settings cannot
be changed. Turn the function off to change the settings.
Setting Extended Security
Preparation
The Extended Security setting is not available unless the key operator code set
in the Key Operator Code settings of the System Settings has six or more digits. See p.60 “Key Operator Code”.
8
Note
❒ To ensure increased document protection under the Extended Security setting, we recommend you select [All Initial Settings] when programming a key
operator code.
A Press the {User Tools/Counter}} key.
B On the display panel, press [System Settings], and then press [Key Operator
Tools].
C Press [Extended Security]. Press [On], and then [OK].
The Extended Security function is enabled, and the security mark
in the upper right of the display panel.
146
D Press the {User Tools/Counter}} key to finish.
appears
RussianC3_ENgsg-F_FM.book Page 147 Monday, June 16, 2003 6:48 PM
Security
Unlocking a locked document
Unlock a document that was locked because a wrong password was entered
multiple times, making it available for authorized users to access again.
A Press the {User Tools/Counter}} key.
B On the display panel, press [System Settings], [Key Operator Tools], [TTNext] and
then press [Password Management for Stored Files].
C Press [OK] under Unlock Files.
The document is unlocked.
D Press the {User Tools/Counter}} key to finish.
Temporarily Disabling Document Security
If you forget a password, document protection can be temporarily disabled,
making documents available for operations such as setting new passwords or
deleting.
Important
❒ When operations are complete, be sure to press [Do not Unlock] under Temporarily Unlock Files, protecting the document by password again.
Note
❒ For a document stored using Locked Print, only document deletion is available when protection is disabled.
8
A Press the {User Tools/Counter}} key.
B On the display panel, press [System Settings], [Key Operator Tools], [TTNext] and
then press [Password Management for Stored Files].
C Press [Unlock] under Temporarily Unlock Files.
Note
❒ Protection can be disabled for only three minutes. Access the document,
set a new password, and perform any other necessary operations to the
document within that time. Documents will automatically return to the
password-protected condition after three minutes.
D Press the {User Tools/Counter}} key to finish.
147
RussianC3_ENgsg-F_FM.book Page 148 Monday, June 16, 2003 6:48 PM
Security
Operating Environment and Notes
Security for this machine is assured on the premises that the machine is used under the following conditions:
Operating Environment
• The condition of the machine is normal. (For example, it is not damaged,
modified, or lacking components.)
• When the machine is connected to a network, the machine is protected from
illegitimate access including unauthorized packet sniffing.
• The machine is managed by an administrator with thorough knowledge of
the machine and capable of providing the proper conditions under which users can use the machine safely.
For Administrator
• This machine does not protect against illegitimate actions on the network. To
avoid any risks on the network, further security is required.
• Security of this machine cannot be assured if any hardware component is detached or replaced with an inappropriate component. If these things have the
possibility of occurring, other security measures are necessary.
• Regularly check that the Extended Security function is on. While the machine
is in this mode, the security mark is displayed at the upper right of the display panel. Be sure to check it particularly after the machine is moved or a
power failure occurs. See p.146 “Setting Extended Security”.
• Avoid using a single number or consecutive numbers for an key operator
code such as “00000000” or “12345678”. Since the numbers like this are easy
to guess, using them will not provide the appropriate level of security.
• Remote document management using SmartNetMonitor for AdminSmartNetMonitor for Admin is not available when the Extended Security function
is on.
• User code is a function to help manage the use of the machine. It is not to protect confidential documents from others. See p.70 “User Codes”.
• As for using the delivery function, the security of this machine can assure
only the protection of documents having a password set and stored in the
Document Server. Be sure to select the destination correctly when delivering
documents.
8
148
RussianC3_ENgsg-F_FM.book Page 149 Monday, June 16, 2003 6:48 PM
Operating Environment and Notes
For User
• Be careful not to let anyone know your password, especially when entering a
password or recording it. Keep any record of your password in a safe place.
• Avoid using a single number or consecutive numbers for a password such as
“0000” or “1234”, since the numbers like this are easy to guess, so using them
will not provide a worthwhile level of security.
• A document accessed with a correct password remains selected even after operations are complete, and it can be accessed by other users. To stop this, be
sure to press the {Clear Modes}
} key to cancel the document selection.
• The user name used when adding a document to the Document Server is to
identify the document creator and type. It is not to protect confidential documents from others.
• Before scanning documents using the scanner function, make sure all other
operations are complete.
8
149
RussianC3_ENgsg-F_FM.book Page 150 Monday, June 16, 2003 6:48 PM
Security
8
150
RussianC3_ENgsg-F_FM.book Page 151 Monday, June 16, 2003 6:48 PM
9. Specifications
Main Unit
❖ Configuration:
Desktop
❖ Photosensitivity type:
OPC drum ( 30)
❖ Original scanning:
One-dimensional solid scanning system through CCD
❖ Copy process:
Dry electrostatic transfer system
❖ Development:
Dry two-component magnetic brush development system
❖ Fusing:
Heating roll pressure system
❖ Resolution:
600 dpi
❖ Exposure glass:
Stationary original exposure type
❖ Original reference position:
Rear left corner
❖ Warm-up time:
• Main power switch: 15 seconds or less (20 °C, 68 °F)
• Operation switch: 10 seconds or less (20 °C, 68 °F)
❖ Originals:
Sheet/book/objects
❖ Maximum original size:
A3L, 11" × 17"L
151
RussianC3_ENgsg-F_FM.book Page 152 Monday, June 16, 2003 6:48 PM
Specifications
❖ Copy paper size:
• Tray 1: A3L – A5L, 11" × 17"L – 51/2" × 81/2"L
• Tray 2: A3L – A6L, 11" × 17"L – 51/2" × 81/2"L
• Bypass: A3L – A6L, 11" × 17"L – 51/2" × 81/2"L
• Tray 2 (custom size):
Vertical: 100 – 297 mm, 4.0" – 11.7"
Horizontal: 148 – 432 mm, 5.9" – 17.0"
• Bypass (custom size):
Vertical: 90 – 305 mm, 3.6" – 12.0"
Horizontal: 148 – 600 mm, 5.9" – 23.6"
• Duplex: A3L – A5L, 11" × 17"L – 51/2" × 81/2"L (impossible on A5K,
51/2" × 81/2" K)
• LCT: A4K, 81/2" × 11"K
❖ Copy paper weight:
• Paper tray 1: 60 – 90 g/m2, 16 – 24 lb.
• Paper tray 2: 52 – 157 g/m2, 14 – 42 lb.
• Bypass tray: 52 – 157 g/m2, 14 – 42 lb.
❖ Non-reproduction area:
• Leading edge: 3 ± 2 mm or less
• Trailing edge: 0.5 mm or more
• Left edge: 2 ± 1.5 mm or less
• Right edge: 2 + 2.5/-1.5 mm or less
❖ First copy time:
Type 1, 2: 5.0 seconds or less
Type 3: 4.5 seconds or less
(A4K, 81/2" × 11"K, 100%, feeding from the tray 1, on the exposure glass,
Text mode, Auto Image Density)
9
❖ Copying speed: (Type 1)
• 13 copies/minute (A3L, 11" × 17"L)
• 15 copies/minute (B4 JISL)
• 22 copies/minute (A4K, 81/2" × 11"K)
❖ Copying speed: (Type 2)
• 15 copies/minute (A3L, 11" × 17"L)
• 17 copies/minute (B4 JISL)
• 27 copies/minute (A4K, 81/2" × 11"K)
152
RussianC3_ENgsg-F_FM.book Page 153 Monday, June 16, 2003 6:48 PM
Main Unit
❖ Copying speed: (Type 3)
• 18 copies/minute (A3L, 11" × 17"L)
• 21 copies/minute (B4 JISL)
• 32 copies/minute (A4K, 81/2" × 11"K)
❖ Reproduction ratio:
Preset reproduction ratios:
Metric version
Enlargement
Inch version
400%
400%
200%
200%
141%
155%
122%
129%
115%
121%
Full size
100%
100%
Reduction
93%
93%
82%
85%
75%
78%
71%
73%
65%
65%
50%
50%
25%
25%
Zoom: From 25 to 400% in 1% steps (from 25 to 200% in 1% step, when setting
originals in the ADF).
❖ Maximum continuous copy run:
99 sheets
9
❖ Paper capacity:
• Tray 1, 2: 500 sheets (80 g/m2, 20 lb.)
• Bypass tray: 100 sheets (80 g/m2, 20 lb.)
153
RussianC3_ENgsg-F_FM.book Page 154 Monday, June 16, 2003 6:48 PM
Specifications
❖ Power consumption:
• Main unit only
Warm-up
Type 1/Type 2
Type 3
less than 1.44 kW
less than 1.44 kW
Stand-by
about 150 W
*2
about 150 W *2
During printing
about 650 W *2
about 770 W *2
less than 1.44 kW
less than 1.44 kW
Type 1/Type 2
Type 3
Maximum
• Complete system
*1
Warm-up
less than 1.44 kW
less than 1.44kW
Stand-by
about 160 W *2
about 160 W *2
During printing
about 680 W *2
about 800 W *2
Maximum
less than 1.44 kW
less than 1.44 kW
*1
*2
The Complete system consists of the main unit, ADF, 1000-sheet finisher, duplex unit, internal tray 2, paper tray unit, fax unit, ISDN, extra G3 interface
unit, expansion memory, JBIG function upgrade unit, printer unit, HDD, PHY
and memory unit.
The measurements are actual values.
❖ Dimensions (W × D × H up to exposure glass):
Type 1, 2, 3: 550 × 604 × 709 mm, 21.7" × 23.8" × 28.0"
❖ Space for main unit (W × D):
Type 1, 2, 3: 550 × 604 mm, 21.7" × 23.8"
❖ Noise Emission *1 :
Sound Power Level:
• Main unit only
9
Type 1/Type 2
Type 3
Stand-by
Less than 40 dB (A)
Less than 40 dB (A)
Copying
Less than 63 dB (A)
Less than 66 dB (A)
Type 1/Type 2
Type 3
• Complete system *3
Stand-by
Less than 44 dB (A)
Less than 44 dB (A)
Copying
Less than 68.5 dB (A)
Less than 70 dB (A)
Type 1/Type 2
Type 3
Sound Pressure Level *2 :
• Main unit only
154
Stand-by
Less than 34 dB (A)
Less than 34 dB (A)
Copying
Less than 57 dB (A)
Less than 60 dB (A)
RussianC3_ENgsg-F_FM.book Page 155 Monday, June 16, 2003 6:48 PM
Main Unit
• Complete system *3
Type 1/Type 2
Type 3
Stand-by
Less than 38 dB (A)
Less than 38 dB (A)
Copying
Less than 61 dB (A)
Less than 64 dB (A)
*1
*2
*3
The above measurements, made in accordance with ISO 7779, are actual values.
Measured at the position of the bystander.
The Complete System consists of the main unit, ADF, 1000-sheet finisher, duplex unit, internal tray 2 and paper tray unit.
❖ Weight:
Type 1, 2, 3: Approx. 55 kg, 121.3 lb.
❖ HDD:
20 GB or more
• Capacity for Document Server
3.6 GB
• Capacity for memory sorting
3.2 GB
• Capacity for others
1.32 GB or more
9
155
RussianC3_ENgsg-F_FM.book Page 156 Monday, June 16, 2003 6:48 PM
Specifications
Options
Exposure Glass Cover
Lower this over originals for copying.
Auto Document Feeder
❖ Mode:
ADF mode, Batch mode, SADF mode, Mixed Size mode, Custom Size originals mode
❖ Original size:
• A3L – A5KL
• 11" × 17"L – 51/2" × 81/2"KL
❖ Original weight:
• One-sided originals: 40 – 128 g/m2 (11 – 34 lb.)
• Two-sided originals: 52 – 105 g/m2 (14 – 28 lb.) (Duplex)
❖ Maximum number of originals:
50 sheets (80 g/m2, 20 lb.) or less than 11 mm, 0.43"
❖ Maximum power consumption:
Less than 50 W (power is supplied from the main unit)
❖ Dimensions (W×
×D×
×H):
550 × 470 × 130 mm, 21.7" × 18.6" × 5.2"
9
❖ Weight:
Approx. 10 kg, 22.1 lb.
Note
❒ Specifications are subject to change without notice.
156
RussianC3_ENgsg-F_FM.book Page 157 Monday, June 16, 2003 6:48 PM
Options
500-Sheet Finisher
❖ Paper size:
A3L, B4 JISL, A4KL, B5 JISK, 11" × 17"L, 11" × 14"L, 81/2" × 14"L, 81/2"
× 11"KL, 81/2" × 13"L, 8" × 101/2"K
❖ Paper weight:
60 – 128 g/m2, 16 – 34 lb.
❖ Stack capacity:
• 500 sheets (A4K, 81/2" × 11"K or smaller) (80 g/m2, 20 lb.)
• 250 sheets (B4 JISL, 81/2" × 14"L or larger) (80 g/m2, 20 lb.)
❖ Staple capacity:
• 30 sheets (A4K, 81/2" × 11"K or smaller) (80 g/m2, 20 lb.)
• 20 sheets (B4 JISL, 81/2" × 14"L or larger) (80 g/m2, 20 lb.)
❖ Staple paper size:
A3L, B4 JISL, A4KL, B5 JISK, 11" × 17"L, 11" × 15"L, 11" × 14"L, 10" ×
14"L, 10" × 15"L, 81/2" × 14"L, 81/2" × 13"L, 81/2" × 11"KL, 8" × 101/2"K,
8" × 10"K, 101/2" × 71/4"K
❖ Staple paper weight:
64 – 90 g/m2, 17 – 24 lb.
❖ Staple position:
1 position (upper left)
❖ Power consumption:
48 W (power is supplied from the main unit)
9
❖ Dimensions (W × D × H):
350 × 490 × 230 mm, 13.8" × 19.3" × 9.1"
❖ Weight:
Approx. 10 kg, 22.1 lb.
157
RussianC3_ENgsg-F_FM.book Page 158 Monday, June 16, 2003 6:48 PM
Specifications
1000-Sheet Finisher
Finisher Upper Tray:
❖ Paper size:
A3L, B4 JISL, A4KL, B5 JISKL, A5KL, B6 JISL, A6L, PostcardL, 11"
× 17"L, 11" × 15"L, 11" × 14"L, 10" × 14"L, 10" × 15"L, 81/2" × 14"L, 81/2"
× 11"KL, 101/2" × 71/4"KL, 8" × 13"L, 81/2" × 13"L, 81/4" × 13"L, 8" ×
101/2"KL, 8" × 10"KL, 81/4" × 14"L, 51/2" × 81/2"KL
❖ Paper weight:
60 – 157 g/m2, 16 – 42 lb.
❖ Stack capacity:
• 250 sheets (A4K, 81/2" × 11"K or smaller) (80 g/m2, 20 lb.)
• 50 sheets (B4 JISL, 81/2" × 14"L or larger) (80 g/m2, 20 lb.)
Finisher Shift Tray:
❖ Paper size:
A3L, B4 JISL, A4KL, B5 JISKL, 11" × 17"L, 11" × 14"L, 81/2" × 14"L,
81/2" × 11"KL, 101/2" × 71/4"L, 8" × 101/2"KL, 8" × 13L, 81/2" × 13"L,
81/4" × 13"L, 81/4" × 14"L, 51/2" × 81/2" KL
❖ Paper weight:
60 – 157 g/m2, 16 – 42 lb.
❖ Stack capacity:
• 1,000 sheets (A4K, 81/2" × 11"K or smaller) (80 g/m2, 20 lb.)
• 500 sheets (B4 JISL, 81/2" × 14"L or larger) (80 g/m2, 20 lb.)
9
❖ Staple capacity:
• 50 sheets (A4K, 81/2" × 11"K or smaller) (80 g/m2, 20 lb.)
• 30 sheets (B4 JISL, 81/2" × 14"L or larger) (80 g/m2, 20 lb.)
❖ Staple paper size:
A3L, B4 JISL, A4KL, B5 JISKL, 11" × 17"L, 11" × 15"L, 11" × 14"L, 10"
× 14"L, 10" × 15"L, 81/2" × 14"L, 81/2" × 11"KL, 101/2" × 71/4"KL, 8" ×
13"L, 81/2" × 13"L, 81/4" × 13"L, 8" × 101/2"KL, 8" × 10"KL, 81/4" × 14"L
❖ Staple paper weight:
64 – 90 g/m2, 17 – 24 lb.
❖ Staple position:
• 1 staple – 2 positions
• 2 staples – 2 positions
158
RussianC3_ENgsg-F_FM.book Page 159 Monday, June 16, 2003 6:48 PM
Options
❖ Power consumption:
Less than 50 W (power is supplied from the main unit)
❖ Dimensions (W × D × H):
527 × 520 × 790 mm, 20.8" × 20.5" × 31.1"
❖ Weight:
Approx. 25 kg, 55.2 lb.
Shift Sort Tray
❖ Paper capacity:
250 sheets (A4K, 81/2" × 11"K or smaller) (80 g/m2, 20 lb.)
125 sheets (B4 JISL, 81/2" × 14" or larger) (80 g/m2, 20 lb.)
❖ Power consumption:
3.6 W (power is supplied from the main unit)
❖ Dimensions (W × D × H)
430 × 372 × 148 mm, 17" × 15" × 6"
❖ Weight:
Approx. 1.6 kg, 3.5 lb.
Duplex Unit
❖ Paper size:
A3L, B4 JISL, A4KL, B5 JISKL, A5L, 5 1/2" × 8 1/2"L, 7 1/4" × 10 1/2"KL,
8" × 10"KL, 8 1/2" × 11"KL, 8" × 13"L, 8 1/2" × 13"L, 81/2" × 14"L, 8 1/4" ×
13"L, 11" × 17"L
9
❖ Paper weight:
64 – 90 g/m2, 20 – 24 lb.
❖ Power consumption (Max):
35 W (power is supplied from the main unit)
❖ Dimensions (W × D × H):
90 × 495 × 455 mm, 3.6" × 19.5" × 17.9"
❖ Weight:
Approx. 6 kg, 13.3 lb.
159
RussianC3_ENgsg-F_FM.book Page 160 Monday, June 16, 2003 6:48 PM
Specifications
Bypass Tray
❖ Paper size:
• Standard size: A3L – A6L, 11" × 17"L – 51/2" × 81/2"L
• Custom size: Vertical (100 – 297 mm, 4.0" – 11.7"), Horizontal (148 – 432
mm, 5.9" – 17.0")
❖ Paper weight:
52 – 157 g/m2, 14 – 42 lb.
❖ Dimensions (W × D × H):
296 × 495 × 163 mm, 11.7" × 19.5" × 6.5"
❖ Paper capacity:
52 – 90 g/m2, 16 – 20 lb: 100 sheets
❖ Weight:
Approx. 2.5 kg, 5.6 lb.
Bridge Unit
❖ Dimensions:
413 × 435 × 126 mm, 16.3" × 17.1" × 5.0"
❖ Weight:
3.6 kg, 7.9 lb.
Internal Tray 2 (1 bin tray)
9
❖ Number of bins:
1
❖ Available paper size:
A3L, B4 JISL, A4KL, B5 JISKL, A5K, 11" × 17"L, 81/4" × 14"L, 81/2" ×
14"L, 11" × 15"L, 11" × 14"L, 10" × 14"L, 10" × 15"L, 81/2" × 11"KL, 101/2"
× 71/4" KL, 8" × 13"L, 81/2" × 13"L, 81/4" × 13"L, 8" × 101/2"KL, 8" ×
10"KL, 51/2" × 81/2" L
❖ Paper capacity:
125 sheets (80 g/m2, 20 lb.)
❖ Paper weight:
60 – 90 g/m2 (16 – 24 lb.)
160
RussianC3_ENgsg-F_FM.book Page 161 Monday, June 16, 2003 6:48 PM
Options
❖ Maximum power consumption:
Less than 15 W (power is supplied from the main unit)
❖ Dimensions (W × D × H):
530 × 410 × 120 mm, 20.9" × 16.2" × 4.7"
❖ Weight:
Approx. 1.1 kg, 2.5 lb.
Note
❒ Specifications are subject to change without notice.
Large Capacity Tray
❖ Paper size:
A4K, 81/2" × 11"K
❖ Paper weight:
60 – 90 g/m2, 16 – 24 lb.
❖ Paper capacity:
2,000 sheets (80 g/m2, 20 lb.)
❖ Power consumption
Maximum. 40 W (power is supplied from the main unit)
❖ Dimensions (W × D × H, option unit):
550 × 520 × 271 mm, 21.7" × 20.5" × 10.7"
❖ Weight:
Approx. 25 kg, 55.2 lb.
9
Note
❒ Specifications are subject to change without notice.
Paper Tray Unit
❖ Paper weight:
60 – 90 g/m2 (16 – 24 lb.)
❖ Available paper size:
A3L, B4 JISL, A4KL, B5 JISKL, A5L, 11" × 17"L, 81/2" × 14"L, 81/2" ×
11"KL, 51/2" × 81/2" L, 81/4" × 14"L, 11" × 14"L, 71/4" × 101/2" K, 8" ×
13"L, 8" × 101/2"KL, 81/2" × 13"L, 81/4" × 13"L
❖ Maximum power consumption:
Less than 30 W (power is supplied from the main unit)
161
RussianC3_ENgsg-F_FM.book Page 162 Monday, June 16, 2003 6:48 PM
Specifications
❖ Paper capacity:
500 sheets (80 g/m2, 20 lb.) × 2 trays
❖ Dimensions (W × D × H):
550 × 520 × 271 mm, 21.7" × 20.5" × 10.7"
❖ Weight:
Approx. 25 kg, 55.2 lb.
Note
❒ Specifications are subject to change without notice.
9
162
RussianC3_ENgsg-F_FM.book Page 163 Monday, June 16, 2003 6:48 PM
Copy Paper
Copy Paper
Recommended Paper Sizes and Types
The following limitations apply to each tray:
Tray
Type
Paper Type and
Weight
Metric Version
Tray 1
60-90 g/m2
(16-24 lb.)
A3L, B4 JISL, A4KL, B5 JISKL, A5L
*10
(optional)
*2
*10
Paper
Capacity
500 sheets
*1
11" ×17"L, 81/2" × 14"L, 81/2" × 11"KL, 8" ×
13"L, 81/2" × 13"L, 81/4" × 13"L, 81/4" × 14"L, 11"
× 14"L, 71/4" × 101/2"K, 8" × 101/2"KL, 51/2" ×
81/2"L, 8KL, 16KKL
Paper
Tray
Unit *10
Tray 2
Inch Version
60-90 g/m2
(16-24 lb.)
Thin paper
52-60 g/m2
(14-16 lb.)
Custom size
*2
Custom size
Vertical: 140-297 mm
Vertical: 5.6"-11.7"
Horizontal: 182-600 mm
Horizontal: 7.3"-23.6"
A3L, B4 JISL, A4KL, B5 JISKL, A5L
500 sheets
B6 JISL, A6L, 11" × 17"L, 8 /2" × 14"L, 8 /2" ×
11"KL, 51/2" × 81/2"L, 71/4" × 101/2" KL, 8" ×
13"L, 81/2" × 13"L, 81/4" × 13"L, 8" × 10"KL,
81/4" × 14"L, 11" × 14"L, 8" × 101/2"KL, 11" ×
15"L, 10" × 14"L, 10" × 15"L, 8KL, 16KKL
*1
*2
1
Custom size
*2
1
Custom size
Vertical: 100-297 mm
Vertical: 4.0"-11.7"
Horizontal: 148-600 mm
Horizontal: 5.9"-23.6"
Thick paper *11
A3L, B4 JISL, A4KL, B5 JISKL, A5L
105-157 g/m2
(28-42 lb.)
B6 JISL, A6L, 11" × 17"L, 8 /2" × 14"L, 8 /2" ×
11"KL, 51/2" × 81/2"L, 71/4" × 101/2" KL, 8" ×
13"L, 81/2" × 13"L, 81/4" × 13"L, 8" × 10"KL,
81/4" × 14"L, 11" × 14"L, 8" × 101/2"KL, 11" ×
15"L, 10" × 14"L, 10" × 15"L, 8KL, 16KKL
*1
*2
Translucent paper
1
Custom size
*2
*7
9
1
Custom size
Vertical: 100-297 mm
Vertical: 4.0"-11.7"
Horizontal: 148-432 mm
Horizontal: 5.9"-17.0"
A3L, B4 JISL, A4KL, B5 JISKL
OHP transparencies A4KL
Postcards
100 × 148 mm
Label paper
(adhesive labels)
B4 JISL, A4L
Envelope
37/8" × 71/2"L, 41/8" × 91/2"L, C5 EnvL, C6 EnvL,
DL EnvL
–
163
RussianC3_ENgsg-F_FM.book Page 164 Monday, June 16, 2003 6:48 PM
Specifications
Tray
Type
Paper Type and
Weight
Bypass 52-90 g/m2
Tray *10 (14-24 lb.)
(optional) Thin paper
52-60 g/m2
(14-16 lb.)
Metric Version
Inch Version
Paper
Capacity
A3L, B4 JISL, 11" × 17"L, 81/2" × 14"L, 8" × 13"L,
81/2" × 13"L, 81/4" × 13"L, 81/4" × 14"L, 11" ×
14"L, 11" × 15"L, 10" × 14"L, 10" × 15"L, 8KL
10 sheets
A4KL, B5 JISKL, A5KL, B6 JISL
100 sheets
A6L, 81/2" × 11"KL, 51/2" × 81/2"L, 71/4" ×
101/2"LK, 8" × 10"KL, 8" × 101/2"KL, 16KKL
*3
*4
Custom size
*4
Custom size
Vertical: 90-305 mm
Vertical: 3.6"-12.0"
Horizontal: 148-432 mm
Horizontal: 5.9"-17.0" *12
*8
*12
Thick paper *11
2
105-157 g/m
(28-42 lb.)
A3L, B4 JISL, 11" × 17"L, 81/2" × 14"L, 8" × 13"L,
81/2" × 13"L, 81/4" × 13"L, 81/4" × 14"L, 11" ×
14"L, 11" × 15"L, 10" × 14"L, 10" × 15"L, 8KL
10 sheets
A4KL, B5 JISKL, A5KL, B6 JISL
40 sheets
A6L,
2" × 11"KL,
2" ×
2"L,
4" ×
101/2"KL, 8" × 10"KL, 8" × 101/2"KL, 16KKL
*3
*4
81/
Custom size
51/
*4
81/
71/
Custom size
Vertical: 90-305 mm
Vertical: 3.6"-12.0"
Horizontal: 148-432 mm
Horizontal: 5.9"-17.0" *12
*9
*12
Translucent paper
A3L, B4 JISL
A4KL, B5 JISKL
10 sheets
40 sheets
*5
OHP transparencies A4KL
10 sheets
*5
9
Postcards
100 × 148 mm
40 sheets
*5
Label paper
(adhesive labels)
B4 JISL, A4L
1 sheet
Envelope
37/8" × 71/2"L, 41/8" × 91/2"L, C5 EnvL, C6 EnvL,
DL EnvL
–
A4K, 81/2" × 11"K *6
2000
(1000 +
1000)
sheets
LCT *10 60-90 g/m2
(optional) (16-24lb.)
*1
*2
*3
164
Set the paper size selector to the p mark, and then select the paper size in System
Settings. See "Paper Type".
Set the paper size selector to the p mark, and then specify the paper size. See “Copying from the paper tray 2”, Copy Reference
Place the paper in the bypass tray, and select the paper size. See “When copying onto
standard size paper”, Copy Reference
RussianC3_ENgsg-F_FM.book Page 165 Monday, June 16, 2003 6:48 PM
Copy Paper
*4
*5
*6
*7
*8
*9
*10
*11
*12
Place the paper in the bypass tray, and specify the paper size. See “When copying
onto custom size paper”, Copy Reference
When paper larger than 433 mm is used, it is likely to jam, crease or not feed in properly. Make sure the paper is placed correctly so that feeds in straight.
Placing one sheet at a time is recommended.
The paper tray guide is fixed. If you want to change the size of paper placed in this
tray, contact your service representative.
When loading paper, make sure the stack height does not exceed the lower limit
mark of the paper tray 2. See p.110 “Setting special paper in the paper tray 2”.
When the paper size is larger than A4L, you can load 10 sheets.
When the paper size is smaller than A4L, you can load 100 sheets.
When the thick paper size is larger than A4L, you can load 10 sheets. When the thick
paper size is smaller than A4L, you can load 40 sheets.
When loading copy paper, make sure the stack height does not exceed the limit mark.
The maximum number of sheets you can load at a time depends on the paper thickness and condition.
If you want to copy onto thick (105 g/m2, 28 lb or heavier) paper, select Thick Paper
mode. See "Copying from the Paper Tray 2", Copy Reference.
Paper size up to 600 mm (23.6") is available when the optional HDD is installed.
Important
❒ Damp or curled paper may cause misfeeds.
Note
❒ When loading paper in the paper tray 1-4 and the LCT, place the copy side of
the paper face up.
❒ When loading paper in the bypass tray, place the copy side of the paper face
down.
❒ When using the bypass tray, it is recommended to set the paper orientation to
L.
❒ If you load paper of the same size in the same orientation in two or more
trays, the machine automatically shifts to the other tray when the first tray in
use runs out of paper. This function is called Auto Tray Switching. (However,
if the Paper Type of one tray is recycled or special paper, the settings of the
other trays must be the same for Auto Tray Switching to work.) This saves interrupting a copy run to replenish paper when making a large number of copies. See “Selecting Copy Paper”,“Auto Tray Switching”, Copy Reference
❒ The paper types you can select in System Settings are only general classifications. Copy quality for every kind of paper in a classification is not guaranteed. See p.169 “Unusable Paper”for more information.
9
165
RussianC3_ENgsg-F_FM.book Page 166 Monday, June 16, 2003 6:48 PM
Specifications
Envelopes
Note
❒ Postcards and envelopes should be fed from paper tray 2 or the bypass tray.
❒ Some kinds of envelopes might cause misfeeds or wrinkle. If this happens,
push down the green lever of the fusing unit. See p.166 “When copying onto
envelopes”.
❒ Envelopes with large flaps should be fed from paper tray 2 to prevent misfeeds. See the illustration below.
2
When copying onto envelopes
A If the duplex unit is installed, open it by lifting the catch.
9
166
RussianC3_ENgsg-F_FM.book Page 167 Monday, June 16, 2003 6:48 PM
Copy Paper
B Open the right cover by lifting the catch.
C Push down the green fusing unit's lever, as shown.
ZEWH320E
Important
❒ Be sure to return the lever to its original position after you have finished
copying onto envelopes.
❒ If you copy onto plain paper without returning the lever to its original position, the copy quality might be reduced.
9
D Close the right cover.
167
RussianC3_ENgsg-F_FM.book Page 168 Monday, June 16, 2003 6:48 PM
Specifications
E If the duplex unit is installed, close it.
F Press the {#}} key.
G Select the paper size, and then select [Thick Paper] for the paper type.
H Press [OK].
I Place your originals, and then press the {Start}} key.
Note
❒ When copying onto OHP transparencies, remove copies one by one.
❒ When setting OHP transparencies, thin paper or label paper (adhesive labels), Staple, Shift or Sort function may not be used.
J When your copy job is finished, press the {Clear Modes}} key to clear the settings.
9
168
RussianC3_ENgsg-F_FM.book Page 169 Monday, June 16, 2003 6:48 PM
Copy Paper
Unusable Paper
R CAUTION:
• Do not use aluminum foil, carbon paper, or similar conductive paper to avoid
a fire or machine failure.
Important
❒ To prevent faults, do not use any of the following kinds of paper:
• Thermal fax paper
• Art paper
• Aluminum foil
• Carbon paper
• Conductive paper
• OHP transparencies for color copying
• Paper with perforated lines
• Hemmed paper
❒ Do not use copy paper that has been already copied onto, fault could occur if
you do.
Note
❒ To prevent misfeeds, do not use the following kinds of paper:
• Bent, folded, or creased paper
• Torn paper
• Slippery paper
• Perforated paper
• Rough paper
• Thin paper with little stiffness
• Paper with a dusty surface
❒ If you copy onto rough grain paper, the image might be blurred.
9
Paper Storage
Note
❒ When storing paper, the following precautions should always be followed:
• Do not store paper where it will be exposed to direct sunlight.
• Avoid storing paper in humid areas (humidity: 70% or less).
• Store on a flat surface.
❒ Do not store paper vertically.
❒ Under high temperature and humidity conditions, or low temperature and
humidity conditions, store paper in vinyl bags.
169
RussianC3_ENgsg-F_FM.book Page 170 Monday, June 16, 2003 6:48 PM
INDEX
1000-Sheet Finisher, 158
1000-sheet finisher, 19
500-Sheet Finisher, 19
A
Adding staples, 125
Adding toner, 113
Address book, 67
change order, 64
edit title, 65
program/change/delete group, 63
program/change/delete transfer request, 63
select title, 65
Address Book Management, 62
ADF, 19
Auto Delete File, 65
Auto Document Feeder, 17, 156
cleaning, 136
Auto Off, 26
Auto off timer, 58
Auto reset timer
copier/Document Server, 58
facsimile, 59
scanner, 59
system, 58
B
Bridge unit, 19, 160
Browse network, 87
Bypass tray, 18, 19, 160
C
Changing a group name, 97
Changing an LDAP server, 105
Changing a registered e-mail destination, 84
Changing a registered fax destination, 79
Changing a registered FTP folder, 91
Changing a registered SMB folder, 88
Changing a registered Transfer Station/
Receiving Station, 101
Changing a user code, 72
Changing paper, 122
Changing the language, 140
Changing the paper size, 122
Check Modes key, 21
Clear
counter per user code, 61
170
Clearing misfeeds, 116
Clearing the number of prints, 75
Clear Modes key, 21
Clear/Stop key, 22
Combined function operations, 27
Common key operations, 23
Control panel, 18, 21
Copy Count Display, 51
Copy paper, 163
Cover sheet tray, 57
D
Delete
all files, 66
Deleting a group, 98
Deleting a registered e-mail destination, 84
Deleting a registered fax destination, 81
Deleting a registered FTP folder, 92
Deleting a registered SMB folder, 89
Deleting a registered Transfer Station/
Receiving Station, 102
Deleting a user code, 73
Display
counter, 61
counter per user code, 61
Displaying destinations registered in
groups, 97
Displaying the Counter for each user code, 73
Displaying the Total Counter, 141
Display panel, 21, 23
Document Server, 33
Deleting, 43
Printing, 40
Using the Document Server, 35
Do's and Don'ts, 131
Duplex unit, 19, 159
E
E-mail destination, 82
Energy Saver key, 22
Entering text, 143
Environment, 133
Exposure glass, 17
cleaning, 136
Exposure glass cover, 19
cleaning, 136
Extended security, 60
Extended Security function, 145
External charge unit management, 60
External options, 19
RussianC3_ENgsg-F_FM.book Page 171 Monday, June 16, 2003 6:48 PM
F
Fax destination, 76
Finisher
1000-Sheet Finisher, 19
500-Sheet Finisher, 19
Front cover, 18
FTP, 89
Function keys, 22
Function Priority, 51
Function reset timer, 52
Function status indicators, 22
I
Indicators, 21
Inquiry, 140
Inter change unit, 19
Internal options, 20
Internal tray, 17
Internal tray 2 (1 bin tray), 19
Interrupt key, 22
K
# key, 22
Key counter management, 60
Key Operator Code, 60
L
Large Capacity Tray, 161
Large Capacity Tray (LCT), 19
LCT, 161
LDAP server, 103
Loading Paper
Large Capacity Tray, 111
Loading paper, 110
paper tray, 110
M
N
Number keys, 22
O
Operation switch, 22, 24
Options, 156
P
Panel off timer, 58
Panel Tone, 51
Paper
changing, 122
loading, 110
Paper tray, 18
Paper tray 2, 18
Paper tray priority
copier, 55
facsimile, 55
printer, 55
Paper tray unit, 19
Paper type
bypass tray, 56
tray 1–4, 56
Password management for stored files, 66
Power connection, 134
Power indicator, 22
Print
address book, 62
counter, 61
counter per user code, 61
Printing the Counter for each user code, 74
Print Priority, 52
Program/change LDAP server, 66
Program key, 21
Programming an LDAP server, 103
Protection
code, 93, 94
destination, 93
Machine environment, 133
Main power indicator, 17, 22
Main power switch, 17, 24
Maintaining Your Machine, 136
Main Unit, 151
Misfeeds, 116
Moving, 134
Multi-Access, 29
171
RussianC3_ENgsg-F_FM.book Page 172 Monday, June 16, 2003 6:48 PM
R
Receiving Station, 99
Registering a fax destination, 77
Registering an e-mail destination, 82
Registering a new user code, 70
Registering a protection code, 93
Registering a protection code to a group user, 94
Registering a protection code to a single user, 93
Registering a Transfer Station/
Receiving Station, 99
Registering destination information, 68
Registering destinations to a group, 95
Registering Folders, 85
Registering sender information, 69
Registering the Transfer Request, 99
Remarks, 131
Remove Paper Indicator, 18
Removing a destination from a group, 96
Removing jammed staples, 128
Replacing the Photo Conductor Unit, 137
S
Safety information, 10
Sample Copy key, 22
Saving energy, 26
Screen contrast knob, 21
Security, 145
Set date, 59
Set time, 59
Shift sort tray, 19
Slip sheet tray, 57
SMB, 85
Specification
Duplex unit, 159
Shift Sort Tray, 159
Specifications, 151
1000-Sheet Finisher, 158
Auto Document Feeder, 156
bridge unit, 160
internal tray 2 (1 bin tray), 160
Large Capacity Tray (LCT), 161
main unit, 151
paper tray unit, 161
Staples
adding, 125
removing jammed staples, 128
Start key, 22
System Reset, 28
172
T
Toner, 132
adding, 113
storage, 132
To register an FTP folder, 89
To register an SMB folder, 85
Transfer Station, 99
Tray paper size, 55
U
Use LDAP server, 66
User code
management, 59
User codes, 70
User Tools/Counter key, 21
User Tools (System Settings), 47
Using FTP to Connect, 89
Using SMB to Connect, 85
V
Ventilation holes, 17
W
Warm Up Notice (copier/Document Server), 51
Web Image Monitor, 44
RussianC3_ENgsg-F_FM.book Page 173 Monday, June 16, 2003 6:48 PM
MEMO
173
RussianC3_ENgsg-F_FM.book Page 174 Monday, June 16, 2003 6:48 PM
MEMO
174
EN
USA
B097-6507
Paper type: OK Prince Eco G100(55kg), Paper Thickness=80 µm // Pages in book=184 // Print scale=81%
Gap (when printed at 81% scale) = Pages in book × Paper thickness / 2 = 7.360000 mm
Introduction
This manual describes detailed instructions on the operation and notes about the use of this machine.
To get maximum versatility from this machine all operators are requested to read this manual carefully
and follow the instructions. Please keep this manual in a handy place near the machine.
In accordance with IEC 60417, this machine uses the following symbols for the main power switch:
a means POWER ON.
c means STAND BY.
Important
Contents of this manual are subject to change without prior notice. In no event will the company be liable for direct, indirect, special, incidental, or consequential damages as a result of handling or operating the machine.
Notes:
Some illustrations in this manual might be slightly different from the machine.
Certain options might not be available in some countries. For details, please contact your local dealer.
Laser Safety:
CDRH Regulations
This equipment complies with requirements of 21 CFR subchapter J for class 1 laser products. This
equipment contains two 5- milliwatt, 760-800 nanometer wavelength, two GaAlAs laser diodes. This
equipment does not emit hazardous light, since the beam is totally enclosed during all customer modes
of operation and maintenance.
Warning:
Use of controls or adjustment or performance of procedures other than those specified in this manual
might result in hazardous radiation exposure.
Notes:
The model names of the machines do not appear in the following pages. Check the type of your machine before reading this manual. (For details, see P.15 “Machine Types”.)
•
Type 1: 4022/DSm622/LD122/Aficio 2022
•
Type 2: 4027/DSm627/LD127/Aficio 2027
•
Type 3: not available
Certain types might not be available in some countries. For details, please contact your local dealer.
Two kinds of size notation are employed in this manual. With this machine refer to the inch version.
For good copy quality, the supplier recommends that you use genuine toner from the supplier.
The supplier shall not be responsible for any damage or expense that might result from the use of parts
other than genuine parts from the supplier with your office products.
Power Source
120V, 60Hz, 12A or more
Please be sure to connect the power cord to a power source as above. For details about power source,
see P.134 “Power Connection”.
Copyright © 2003
Paper type: OK Prince Eco G100(55kg), Paper Thickness=80 µm // Pages in book=184 // Print scale=81%
Gap (when printed at 81% scale) = Pages in book × Paper thickness / 2 = 7.360000 mm
Operating Instructions
General Settings Guide
1
Getting Started
2
Combined Function Operations
3
Document Server
4
User Tools (System Settings)
5
Troubleshooting
6
Remarks
7
Entering Text
8
Security
9
Specifications
Type for 4022/DSm622/LD122 AG/Aficio 2022
Type for 4027/DSm627/LD127 AG/Aficio 2027
Printed in China
EN USA B097-6507
For safe and correct use of this machine, please be sure to read the Safety Information in this
manual before you use it.