Cisco Catalyst 2960-S and 2960 Series Switches with LAN - RRC-u

Data Sheet
Cisco Catalyst 2960-S and 2960 Series Switches
with LAN Lite Software
The Cisco® Catalyst® 2960-S and 2960 Series Switches are the leading Layer 2 edge
switches, providing improved operational excellence, highly secure business
operations, improved sustainability, and an enhanced workspace experience. They
are fixed-configuration access switches designed for entry-level enterprise,
midmarket, and branch office networks. Figure 1 shows the Cisco Catalyst 2960-S
Series Switch model and Figure 2 shows the Cisco Catalyst 2960 Series Switch
model with LAN Lite software.
The Cisco Catalyst 2960-S Series Switches with LAN Lite Software have the following capabilities:
●
24 and 48 ports of Gigabit Ethernet (GbE) 10/100/1000 desktop connectivity
●
1 GbE Small Form-Factor Pluggable (SFP) uplinks
●
USB storage interface for file backup, distribution, and simplified operations
●
Enhanced troubleshooting for problem solving, including link connectivity and cable diagnostics
●
Single IP address management for up to 16 switches
●
A wide range of software features to provide ease of operation, secure business operations, sustainability
and borderless networking experience
●
Limited lifetime hardware warranty, including next-business-day replacement with 90-day service and
support
The Cisco Catalyst 2960 Series Switches with LAN Lite Software have the following capabilities:
●
Fast Ethernet connectivity with Power over Ethernet (PoE) of up to 15.4W per port
●
GbE for data connectivity
●
Enhanced troubleshooting for problem solving, including link connectivity and cable diagnostics
●
Single IP address management for up to 16 switches
●
A wide range of software features to provide ease of operation, highly secure business operations,
sustainability, and a borderless networking experience
●
Limited lifetime hardware warranty
© 2011 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 1 of 17
Figure 1.
Cisco Catalyst 2960-S and 2960 Series Switches with LAN Lite Software
Figure 2.
Cisco Catalyst 2960-S Series Switches with LAN Lite Software
Switch Configurations
Table 1 shows the configuration information for the Cisco Catalyst 2960-S and 2960 Series Switches with LAN Lite
Software.
Table 1.
Configurations of Cisco Catalyst 2960-S and 2960 Series Switches with LAN Lite Software
Switch Model
Description
Uplinks
Catalyst 2960-S Switches with 1 Gigabit Uplinks and 10/100/1000 Ethernet Connectivity
Cisco Catalyst 2960S-48TS-S
48 Ethernet 10/100/1000
2 1 GbE ports
Cisco Catalyst 2960S-24TS-S
24 Ethernet 10/100/1000
2 1 GbE SFP ports
Catalyst 2960 Switches with 1 Gigabit Uplinks and 10/100 Ethernet Connectivity
Cisco Catalyst 2960-48PST-S
48 Ethernet 10/100/1000 PoE ports (370W capacity)
2 fixed 10/100/1000 ports and 2 SFP ports
Cisco Catalyst 2960-24PC-S
24 Ethernet 10/100 PoE ports (370W capacity)
2 dual-purpose ports (10/100/1000 or SFP)
Cisco Catalyst 2960-24LC-S
24 Ethernet 10/100 and 8 10/100 PoE ports (123W
capacity)
2 dual-purpose ports (10/100/1000 or SFP)
Cisco Catalyst 2960-48TC-S
48 Ethernet 10/100
2 dual-purpose ports (10/100/1000 or SFP)
Cisco Catalyst 2960-48TT-S
48 Ethernet 10/100
2 fixed 10/100/1000 ports
Cisco Catalyst 2960-24TC-S
24 Ethernet 10/100
2 dual-purpose ports (10/100/1000 or SFP)
Cisco Catalyst 2960-24-S
24 Ethernet 10/100
None
8 Ethernet 10/100 compact size with no fan
1 dual-purpose port (10/100/1000 or SFP)
Compact Switches
Cisco Catalyst 2960-8TC-S
Cisco Catalyst 2960-S and 2960 Series Switches Enable Cisco Borderless Network
The Cisco Borderless Network Architecture delivers the new workspace experience, connecting anyone,
anywhere, using any device, to any resource securely, reliably, and transparently. The Cisco Borderless Networks
architecture addresses primary IT and business challenges to help create a truly borderless experience by
bringing interactions closer to the employee and customer.
© 2011 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 2 of 17
Borderless experience is only possible with intelligent network elements designed and architected to meet the
needs of a global workspace. Cisco Network Access is a primary component of this architecture, enabling various
borderless network services such as mobility, security, EnergyWise, and ease of operations for increased
productivity and operational efficiency.
Cisco Network Access for Borderless solution focuses on the following primary areas:
●
Sustainability
●
Ease of operations
●
Borderless security
●
Borderless experience
Sustainability
Cisco Catalyst switching solutions enable greener practices through measurable power efficiency, integrated
services, and continuous innovations such as Cisco EnergyWise, an enterprisewide solution that monitors and
conserves energy with customized policies. Together, Cisco EnergyWise technology and Cisco Catalyst switches
reduce greenhouse gas (GhG) emissions and increase energy cost savings and sustainable business behavior.
Sustainability features in the Cisco Catalyst 2960-S and 2960 Series Switches include the following features sets:
●
Cisco EnergyWise technology
●
Efficient switch operation
●
Intelligent power management
Cisco EnergyWise Technology
Cisco EnergyWise is an innovative architecture, added to fixed configuration switches, promoting companywide
sustainability by reducing energy consumption across an entire corporate infrastructure and affecting more than
50 percent of global greenhouse gas emissions created by worldwide building infrastructure, a much greater effect
than the 2 percent generated by the IT industry. Cisco EnergyWise enables companies to measure the power
consumption of network infrastructure and network-attached devices and manage power consumption with
specific policies, reducing power consumption to realize increased cost savings, potentially affecting any powered
device.
EnergyWise encompasses a highly intelligent network-based approach to communicate messages that measure
and control energy between network devices and endpoints. The network discovers Cisco EnergyWisemanageable devices, monitors their power consumption, and takes action based on business rules to reduce
power consumption. EnergyWise uses a unique domain-naming system to query and summarize information from
large sets of devices, making it simpler than traditional network management capabilities. Cisco EnergyWise’s
management interfaces allow facilities and network management applications to communicate with endpoints and
each other using the network as a unifying fabric. The management interface uses standard Simple Network
Management Protocol (SNMP) or TCP to integrate Cisco and third-party management systems.
Efficient Switch Operation
Cisco Catalyst 2960-S and 2960 Series Switches, designed and engineered by Cisco, provide optimum power
saving, low power operations for industry best-in-class power management, and power consumption capabilities.
The Catalyst 2960-S ports are capable of reduced power modes so that ports not in use can move into a lower
power utilization state.
© 2011 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 3 of 17
Intelligent Power over Ethernet Management
The Cisco Catalyst 2960 Series PoE models support the latest PoE devices including Cisco IP phones and Cisco
Aironet WLAN access points providing up to 15.4W of power per port, as well as any IEEE 802.3af-compliant end
device.
●
Per port power consumption command allows customers to specify maximum power setting on an
individual port.
●
Cisco Discovery Protocol Version 2 allows switches to negotiate a more granular power setting when
connecting to a Cisco powered device such as IP phones or access points than what is provided by IEEE
classification.
●
PoE MIB provides proactive visibility into power usage and allows customers to set different power-level
thresholds.
●
IEEE 802.3af and Cisco prestandard PoE support comes with automatic discovery to detect a Cisco
prestandard or IEEE 802.3af endpoint and provide the necessary power without any user configuration.
Per-port PoE power sensing measures the actual power being drawn, enabling more intelligent control of
powered devices.
Table 2 lists the PoE capacity of the Cisco Catalyst 2960 Series Switches.
Table 2.
Switch PoE Power Capacity
Switch Model
Maximum Number of PoE Ports*
Available PoE Power
Cisco Catalyst 2960-48PST-S
24 ports up to 15.4W
370W
48 ports up to 7.7W
Cisco Catalyst 2960-24PC-S
24 ports up to 15.4W
370W
Cisco Catalyst 2960-24LC-S
8 ports up to 15.4W
123W
*Intelligent power allows flexible power allocation across all ports.
Ease of Operations
The Cisco Catalyst 2960-S and 2960 Series Switches help reduce the operating costs through:
●
Cisco Catalyst Smart Operations
●
Easy to use deployment and control features
●
Advanced, intelligent network management tools
Cisco Catalyst Smart Operations
Cisco Catalyst Smart Operations is a comprehensive set of capabilities that simplify LAN deployment,
configuration, and troubleshooting. Cisco Catalyst Smart Operations enable zero-touch installation and
replacement of switches, fast upgrade, as well as ease of troubleshooting with reduced operational cost.
Cisco Catalyst Smart Operations is a set of features that includes Smart Install, Auto Smartports, Smart
Configuration, and Smart Troubleshooting to enhance operational excellence:
●
Cisco Smart Install is a transparent plug-and-play technology to configure the Cisco IOS Software image
and switch configuration without user intervention. Smart Install utilizes dynamic IP address allocation and
the assistance of other switches to facilitate installation providing transparent network plug and play.
© 2011 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 4 of 17
●
Cisco Auto Smartports provide automatic configuration as devices connect to the switch port, allowing
auto detection and plug and play of the device onto the network.
Easy to Use Deployment and Control Features
●
Auto-negotiation on all ports automatically selects half- or full-duplex transmission mode to optimize
bandwidth.
●
Dynamic Trunking Protocol (DTP) facilitates dynamic trunk configuration across all switch ports.
●
Port Aggregation Protocol (PAgP) automates the creation of Cisco Fast EtherChannel groups or Gigabit
®
EtherChannel groups to link to another switch, router, or server.
●
Link Aggregation Control Protocol (LACP) allows the creation of Ethernet channeling with devices that
conform to IEEE 802.3ad. This feature is similar to Cisco EtherChannel technology and PAgP.
●
Automatic media-dependent interface crossover (MDIX) automatically adjusts transmit and receive
pairs if an incorrect cable type (crossover or straight-through) is installed.
●
Unidirectional Link Detection Protocol (UDLD) and Aggressive UDLD allow unidirectional links caused
by incorrect fiber-optic wiring or port faults to be detected and disabled on fiber-optic interfaces.
●
Dynamic Host Configuration Protocol (DHCP) autoconfiguration of multiple switches through a boot
server eases switch deployment.
●
Switching Database Manager (SDM) templates for access, routing, and VLAN deployment allow the
administrator to easily maximize memory allocation to the desired features based on deployment-specific
requirements.
●
Local Proxy Address Resolution Protocol (ARP) works in conjunction with Private VLAN Edge to
minimize broadcasts and maximize available bandwidth.
●
Internet Group Management Protocol (IGMP) Snooping for IPv4 and IPv6 MLD v1 and v2 Snooping
provide fast client joins and leaves of multicast streams and limit bandwidth-intensive video traffic to only
the requestors.
●
Per-port broadcast, multicast, and unicast storm control prevents faulty end stations from degrading
overall systems performance.
●
Voice VLAN simplifies telephony installations by keeping voice traffic on a separate VLAN for easier
administration and troubleshooting.
●
Cisco VLAN Trunking Protocol (VTP) supports dynamic VLANs and dynamic trunk configuration across
all switches.
●
Switch Port Analyzer (SPAN) allows administrators to monitor ports in a Layer 2 switch network from any
other switch in the same network.
●
For enhanced traffic management, monitoring, and analysis, the Embedded Remote Monitoring (RMON)
software agent supports four RMON groups (history, statistics, alarms, and events).
●
Trivial File Transfer Protocol (TFTP) reduces the cost of administering software upgrades by
downloading from a centralized location.
●
Network Timing Protocol (NTP) provides an accurate and consistent timestamp to all intranet switches.
●
Cisco Emergency Responder (CER) enhances emergency calling from Cisco Unified CallManager. It
helps assure that Cisco Unified CallManager sends emergency calls to the appropriate Public Safety
Answering Point (PSAP) for the caller's location.
© 2011 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 5 of 17
Advanced, Intelligent Network Management Tools
The Cisco Catalyst 2960-S and 2960 Series Switches offer both a superior CLI for detailed configuration and
Cisco Network Assistant software, a PC-based tool for quick configuration based on preset templates. In addition,
CiscoWorks LAN Management Solution (LMS) supports the Cisco Catalyst 2960-S and 2960 Series Switches for
networkwide management.
Cisco Network Assistant
A PC-based network management application designed for small and medium-sized business (SMB) networks
with up to 250 users, Cisco Network Assistant offers centralized network management and configuration
capabilities. Cisco Network Assistant uses Cisco Smartports technology to simplify both initial deployment and
ongoing maintenance. This application also features an intuitive GUI where users can easily apply common
services across Cisco switches, routers, and access points, such as:
●
Configuration management
●
Troubleshooting advice
●
Inventory reports
●
Event notification
●
Network security settings
●
Password synchronization
●
Drag-and-drop Cisco IOS Software upgrades
●
Secure wireless
For detailed information about Cisco Network Assistant, visit http://www.cisco.com/go/cna.
CiscoWorks LAN Management Solution
CiscoWorks LAN Management Solution (LMS) is a comprehensive network lifecycle management solution. It
provides an extensive library of easy-to-use features to automate the initial and day-to-day management of your
Cisco network infrastructure. CiscoWorks LMS uniquely uses Cisco hardware and software platform knowledge
and operational experience into a powerful set of workflow driven configuration, monitoring, troubleshooting,
reporting, and administrative tools. Including:
●
Support for new Cisco hardware platforms the day they ship
●
Support for new technologies and services from initial deployment to day-to-day administration and
management, such as EnergyWise, Identity, Cisco Auto Smartports, Cisco Smart Install, and much more
●
Configuration management tools built from Cisco experience and Cisco Validated Design
recommendations
●
Monitoring and troubleshooting capabilities that incorporates Cisco hardware best practices and
diagnostics features
●
Automation in managing hardware inventories, security vulnerabilities (PSIRTS) and platform end-of-life
and support cycles
For detailed information about CiscoWorks LMS, go to:
http://www.cisco.com/en/US/products/sw/cscowork/ps2425/index.html.
© 2011 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 6 of 17
Borderless Security
The Cisco Catalyst 2960-S and 2960 LAN Lite Series Switches provide basic TrustSec, a primary element of
Borderless Security Architecture, that helps enterprise customers secure their networks, data and resources with
policy-based access control, identity-aware and role-aware networking, pervasive integrity, and confidentiality. The
borderless security is enabled by the following feature sets in the Cisco Catalyst 2960-S and 2960 Series
Switches:
●
Basic Cisco TrustSec
●
Other security features
Cisco TrustSec
●
The Cisco TrustSec solution provides authentication, access control, and security policy administration to
secure network connectivity and resources. On the Cisco Catalyst 2960-S and 2960 Series with LAN Lite,
the TrustSec solution prevents unauthorized access and helps ensure that users get only their designated
privileges. It provides the ability to dynamically administer granular levels of network access.
Other Security Features
Other Advanced Security features include but are not limited to:
●
MAC Auth Bypass (MAB) for voice allows third-party IP phones without an 802.1X supplicant to get
authenticated using their MAC address.
●
Port security can be used to limit access on an Ethernet port based on the MAC address of the device to
which it is connected. It also can be used to limit the total number of devices plugged into a switch port,
thereby protecting the switch from a MAC flooding attack as well as reducing the risks posed by rogue
wireless access points or hubs.
●
The MAC Address Notification feature can be used to monitor the network and track users by sending an
alert to a management station so that network administrators know when and where users enter the
network.
●
Secure Shell (SSH) Protocol v2 and Simple Network Management Protocol (SNMP) v3 provide network
security by encrypting administrator traffic during Telnet and SNMP sessions. SSH v2 and the
cryptographic version of SNMP v3 require a special cryptographic software image because of U.S. export
restrictions.
Borderless Experience
Borderless network enables enterprise mobility and business-grade video services. Industry’s first unified network
(wired and wireless) location services enable tracking of mobile assets and the users of those assets for both
wired and wireless devices. The true borderless experience is enabled by the following feature sets in the Cisco
Catalyst 2960-S and 2960 Series Switches:
●
Layer 2 Networking
●
QoS
© 2011 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 7 of 17
Layer 2 Networking
The Cisco 2960-S and 2960 Series Switches provide Layer 2 networking to enable availability.
Features include but are not limited to:
●
IEEE 802.1s/w Rapid Spanning Tree Protocol (RSTP) and Multiple Spanning Tree Protocol (MSTP)
provide rapid spanning-tree convergence independent of spanning-tree timers and also offers the benefit of
Layer 2 load balancing and distributed processing.
●
Per-VLAN Rapid Spanning Tree (PVRST+) allows rapid spanning-tree reconvergence on a per-VLAN
spanning-tree basis, without requiring the implementation of spanning-tree instances.
●
Switch-port autorecovery (Errdisable) automatically attempts to reactivate a link that is disabled because
of a network error.
●
Up to 64 VLANs and up to 64 spanning-tree instances per switch are supported.
Quality of Service
The Cisco Catalyst 2960-S and 2960 Series Switches offers intelligent services that keep everything flowing
smoothly. Industry-leading mechanisms for marking, classification, and scheduling deliver superior performance
for data, voice, and video traffic, all at wire speed.
Following are some of the QoS features supported in the Cisco 2960-S and 2960 Series Switches:
●
802.1p class of service (CoS) classification provides differentiated services when best-effort traffic
delivery is insufficient.
●
Four egress queues per port help enable differentiated management of different traffic types across the
stack.
●
Shaped Round Robin (SRR) scheduling helps ensure differential prioritization of packet flows by
intelligently servicing the ingress queues and egress queues.
●
Weighted Tail Drop (WTD) provides congestion avoidance at the ingress and egress queues before a
disruption occurs.
Tables 3, 4, 5, 6 and 7 provide hardware features, power specifications, management and standards, and safety
and compliance information for the Cisco Catalyst 2960-S and 2960 Series Switches with LAN Lite Software.
Table 3.
Hardware Features for Cisco Catalyst 2960-S and 2960 Series Switches with LAN Lite Software
Performance and Scalability Numbers for All Switch Models
Forwarding bandwidth
16 Gbps (2960), 50 Gbps (2960-S)
Flash memory
32 MB (2960), 64 MB (2960-S)
Memory DRAM
64 MB (2960), 128 MB (2960-S)
Max VLANs
64
VLAN IDs
4000
Maximum transmission unit (MTU)
Up to 9198 bytes
Jumbo frames
9016 bytes (2960), 9216 bytes (2960-S)
Forwarding Rate
2960S-48TS-S
74.4 mpps
2960S-24TS-S
38.7 mpps
2960-8TC-S
2.7 mpps
© 2011 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 8 of 17
2960-24-S
3.6 mpps
2960-24TC-S
6.5 mpps
2960-24PC-S
6.5 mpps
2960-24LC-S
6.5 mpps
2960-48TT-S
10.1 mpps
2960-48TC-S
10.1 mpps
2960-48PST-S
13.3 mpps
Resource
Default
QoS
Dual
Unicast MAC addresses
8000
8000
8000
IPv4 IGMP groups
256
256
256
IPv4 MAC QoS access control
entries (ACEs)
128
384
0
IPv4 MAC security ACEs
384
128
256
Connectors and Cabling and Indicators
● 10BASE-T ports: RJ-45 connectors, 2-pair Category 3, 4, or 5 unshielded twisted-pair (UTP) cabling
● 100BASE-TX ports: RJ-45 connectors, 2-pair Category 5 UTP cabling
● 1000BASE-T ports: RJ-45 connectors, 4-pair Category 5 UTP cabling
● 1000BASE-T SFP-based ports: RJ-45 connectors, 4-pair Category 5 UTP cabling
● 1000BASE-SX, -LX/LH SFP-based ports: LC fiber connectors (single- and multimode fiber)
● 100Base-FX: LC fiber connectors (single- and multimode fiber)
● Customers can provide power to a switch only by using the internal power supply. The connector is located at the back of the switch. These
switches do not have a redundant-power-supply port.
● The internal power supply is an auto-ranging unit.
● The internal power supply supports input voltages between 100 and 240 VAC.
● Use the supplied AC power cord to connect the AC power connector to an AC power outlet.
● Per-port status: Link integrity, disabled, activity, speed, and full duplex
● System status: System, link status, link duplex, PoE, and link speed
● Per-port status: Link integrity, disabled, activity, speed, and full duplex
● System status: System, link status, link duplex, PoE, and link speed
Dimensions (H x W x D)
Model
Inches
Centimeters
2960S-48TS-S
1.75 x 17.7 x 11.8
4.5 x 45 x 30
2960S-24TS-S
1.75 x 17.7 x 11.8
4.5 x 45 x 30
2960-8TC-S
1.73 x 10.6 x 6.4
4.4 x 27 x 16.3
2960-24-S
1.73 x 17.7 x 9.52
4.4 x 45 x 24.2
2960-24TC-S
1.73 x 17.7 x 9.52
4.4 x 45 x 24.2
2960-24PC-S
1.73 x 17.7 x 13
4.4 x 45 x 33.02
2960-24LC-S
1.73 x 17.7 x 13
4.4 x 45 x 33.02
2960-48TT-S
1.73 x 17.7 x 9.52
4.4 x 45 x 24.2
2960-48TC-S
1.73 x 17.7 x 9.52
4.4 x 45 x 24.2
2960-48PST-S
1.73 x 17.7 x 13
4.4 x 45 x 33.02
Model
Pounds
Kilograms
2960S-48TS-S
10.5
4.8
2960S-24TS-S
10
4.5
2960-8TC-S
3
1.4
2960-24-S
8
3.6
2960-24TC-S
8
3.6
Weight
© 2011 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 9 of 17
2960-24PC-S
12
5.4
2960-24LC-S
10
4.5
2960-48TT-S
8
3.6
2960-48TC-S
8
3.6
2960-48PST-S
12
5.4
Environmental ranges
Fahrenheit
Centigrade
Operating temperature up to 5000 ft (1500
m)
23º to 113ºF
-5º to 45ºC
Operating temperature up to 10,000 ft (3000
m)
23º to 104ºF
-5º to 40ºC
Short-term exception at sea level*
23º to 31ºF
-5º to +55ºC
Short-term exception up to 5,000 feet (1500
m)*
23º to 122ºF
-5º to +50ºC
Short-term exception up to 10,000 feet (3000
m)*
23º to 113ºF
-5º to +45ºC
Storage temperature
Same as above
Same as above
Feet
Meters
Operating altitude
Up to 10,000
Up to 3000
Storage altitude
Up to 13,000
Up to 4000
Operating relative humidity
10% to 95% noncondensing
Storage relative humidity
10% to 95% noncondensing
Acoustic noise
Measured per ISO 7779 and declared per ISO 9296.
Bystander positions operating mode at 25°C ambient.
Sound Pressure
Model
LpA
LpAD
(Typical*)
(Maximum*)
44 dB
2960-24-S
Sound Power
LwA (Typical)
LwAD (Maximum)
47 dB
5.4 B
5.7 B
40 dB
-
-
-
2960-24TC-S
40 dB
-
-
-
2960-24PC-S
48 dB
-
-
-
2960-24LC-S
48 dB
-
-
-
2960-48TT-S
40 dB
-
-
-
2960-48TC-S
40 dB
-
-
-
2960-48PST-S
48 dB
-
-
-
2960S-48TS-S
2960S-24TS-S
*Typical: Noise emission for a typical configuration and PoE load up to 185W
*Maximum: Statistical maximum to account for production variations
Mean time between failures (MTBF)
2960S-48TS-S
357,740 hours
2960S-24TS-S
335,014 hours
2960-8TC-S
615,549 hours
2960-24-S
429,847 hours
2960-24TC-S
403,745 hours
2960-24PC-S
242,818 hours
2960-24LC-S
311,007 hours
© 2011 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 10 of 17
2960-48TT-S
339,743 hours
2960-48TC-S
336,983 hours
2960-48PST-S
181,979 hours
*Not more than the following in a 1-year period. 96 consecutive hours, or 360 hours total, or 15 occurences.
Note: Compact switch 2960-8TC-S (no fan) has 0 dB sound pressure.
Table 4.
Power Specifications for Cisco Catalyst 2960-S and 2960 Series Switches with LAN Lite Software
Description
C2960-S and C2960 Specifications
Models
C2960S48TS-S
C2960S-24TS-S
C2960-8TC-S
C2960-24TC-S
C2960-24PC-S
53W
36W
12W
22W
27W
50W
36W
11W
21W
24W
-
-
Switch Power: 237W
100 Percent Throughput
Measured Power
Consumption
5 Percent Throughput
Measured Power
Consumption
5 Percent Throughput (with 50 Percent PoE Loads)
Measured Power
Consumption
-
-
PoE Power: 185W
100 Percent Throughput (with Maximum Possible PoE Loads)
Measured Power
Consumption
-
-
-
-
Switch Power: 433W
PoE Power: 357W
Description
C2960 Specifications
Models
C2960-24LC-S
C2960-48TT-S
C2960-48TC-S
C2960-48PST-S
79W
71W
55W
52W
78W
70W
54W
50W
-
Switch Power: 460W
100 Percent Throughput
Measured Power
Consumption
5 Percent Throughput
Measured Power
Consumption
5 Percent Throughput (with 50 Percent PoE Loads)
Measured Power
Consumption
Switch Power: 98W
-
PoE Power: 62W
PoE Power: 339W
100 Percent Throughput (with Maximum Possible PoE Loads)
Measured Power
Consumption
Table 5.
Switch Power: 162W
-
-
Switch Power: 262W
PoE Power: 119W
PoE Power: 187W
Voltage and Power Rating for Cisco Catalyst 2960-S and 2960 Series Switches with LAN Lite Software
Voltages and Power Rating
Model
Voltage (Autoranging)
Current
Frequency
2960S-48TS-S
100 to 240 VAC
1 to 0.5 A
50 to 60 Hz
2960S-24TS-S
100 to 240 VAC
1 to 0.5 A
50 to 60 Hz
2960-8TC-S
100 to 240 VAC
0.5 to 0.3 A
50 to 60 Hz
2960-24-S
100 to 240 VAC
1.3 to 0.8 A
50 to 60 Hz
2960-24TC-S
100 to 240 VAC
1.3 to 0.8 A
50 to 60 Hz
2960-24PC-S
100 to 240 VAC
8.0 to 4.0 A
50 to 60 Hz
© 2011 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 11 of 17
Voltages and Power Rating
2960-24LC-S
100 to 240 VAC
3.0 to 1.5 A
50 to 60 Hz
2960-48TT-S
100 to 240 VAC
1.3 to 0.8A
50 to 60 Hz
2960-48TC-S
100 to 240 VAC
1.3 to 0.8A
50 to 60 Hz
2960-48PST-S
100 to 240 VAC
5.0 to 2.0 A
50 to 60 Hz
Model
Power Rating
2960S-48TS-S
0.13 kVA
2960S-24TS-S
0.08 kVA
2960-8TC-S
0.035 kVA
2960-24-S
0.05 kVA
2960-24TC-S
0.05 kVA
2960-24PC-S
0.47 kVA
2960-24LC-S
0.175 kVA
2960-48TT-S
0.075 kVA
2960-48TC-S
0.075 kVA
2960-48PST-S
0.5 kVA
● Maximum power supplied per port for PoE is 15.4W
● Total power dedicated to PoE is 370W
Table 6.
Description
Management
Management and Standards Support for Cisco Catalyst 2960-S and 2960 Series Switches with LAN Lite Software
Specification
● BRIDGE-MIB
● CISCO-CABLE-DIAG-MIB
● CISCO-TC-MIB
● CICSO-TCP-MIB
● CISCO-CDP-MIB
● CISCO-CLUSTER-MI
● CISCO-VLAN-IFTABLE-RELATIONSHIP-MIB
● CISCO-VLAN-IFTABLE-MEMBERSHIP-MIB
● CISCO-CONFIG-COPY-MIB
● CISCO-CONFIG-MAN-MIB
● CISCO-VTP-MIB
● ENTITY-MIB
● CISCO-ENTITY-VENDORTYPE-OID-MIB
● CISCO-ENVMON-MIB
● ETHERLIKE-MIB
● IEEE8023-LAG-MIB
● CISCO-ERR-DISABLE-MIB
● CISCO-FLASH-MIB
● IF-MIB
● INET-ADDRESS-MIB
● CISCO-FTP-CLIENT-MIB
● CISCO-IGMP-FILTER-MIB
● OLD-CISCO-CHASSIS-MIB
● OLD-CISCO-FLASH-MIB
● CISCO-IMAGE-MIB
● CISCO-IP-STAT-MIB
● OLD-CISCO-INTERFACES-MIB
● OLD-CISCO-IP-MIB
● CISCO-LAG-MIB
● CISCO-MAC-NOTIFICATION-MIB
● OLD-CISCO-SYS-MIB
● OLD-CISCO-TCP-MIB
● CISCO-MEMORY-POOL-MIB
● CISCO-PAGP-MIB
● OLD-CISCO-TS-MIB
● RFC1213-MIB
● CISCO-PING-MIB
● CISCO-PORT-QOS-MIB
● RMON-MIB
● RMON2-MIB
● CISCO-PORT-SECURITY-MIB
● CISCO-PORT-STORM-CONTROL-MIB
● SNMP-FRAMEWORK-MIB
● SNMP-MPD-MIB
● CISCO-POWER-ETHERNET-EXT-MIB
● CISCO-PRODUCTS-MIB
● SNMP-NOTIFICATION-MIB
● SNMP-TARGET-MIB
● CISCO-PROCESS-MIB
● CISCO-RTTMON-MIB
● SNMPv2-MIB
● TCP-MIB
● CISCO-SMI-MIB
● CISCO-STP-EXTENSIONS-MIB
● UDP-MIB
● CISCO-SYSLOG-MIB
● Cisco-UDLDP-MIB
© 2011 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 12 of 17
Description
Standards
Specification
● IEEE 802.1D Spanning Tree Protocol
● IEEE 802.1p CoS Prioritization
● 100BASE-FX (SFP)
● 1000BASE-SX (SFP)
● IEEE 802.1Q VLAN
● IEEE 802.1s
● 1000BASE-LX/LH (SFP)
● Remote Monitoring (RMON) I and II standards
● IEEE 802.1w
● IEEE 802.1X
● SNMPv1, v2c, and v3
● IEEE 802.1ab (LLDP without MED*)
● IEEE 802.3ad
● IEEE 802.3ah (100BASE-X single- and multimode fiber only)
● IEEE 802.3x full duplex on 10BASE-T, 100BASE-TX, and
1000BASE-T ports
● IEEE 802.3 10BASE-T specification
● IEEE 802.3u 100BASE-TX specification
● IEEE 802.3ab 1000BASE-T specification
● IEEE 802.3z 1000BASE-X specification
RFC
compliance
● RFC 768 - UDP
● RFC 783 - TFTP
● RFC 1901 - SNMP v2C
● RFC 1902-1907 - SNMP v2
● RFC 791 - IP
● RFC 792 - ICMP
● FRC 2068 - HTTP
● RFC 2131 - DHCP
● RFC 793 - TCP
● RFC 826 - Address Resolution Protocol (ARP)
● RFC 2138 - RADIUS
● RFC 2233 - IF MIB
● RFC 854 - Telnet
● RFC 951 - Bootstrap Protocol (BOOTP)
● RFC 959 - FTP
● RFC 1112 - IP Multicast and IGMP
● RFC 2273-2275 - SNMP v3
● RFC 2474 - Differentiated Services (DiffServ)
Precedence
● RFC 2597 - Assured Forwarding
● RFC 1157 - SNMP v1
● RFC 1166 - IP addresses
● RFC 2598 - Expedited Forwarding
● RFC 2571 - SNMP Management
● RFC 1305 - NTP
● RFC 1492 - TACACS+
● RFC 3046 - DHCP Relay Agent Information Option
● RFC 3376 - IGMP v3
● RFC 1493 - Bridge MIB
● RFC 1542 - BOOTP extensions
● RFC 3580 - 802.1X RADIUS
● RFC 1643 - Ethernet Interface MIB
● RFC 1757 - RMON
*Version with MED will be available starting in release IOS12.2.(55)
Table 7.
Safety and Compliance
Description
Safety certifications
Specification
● UL 60950-1, Second Edition
● CAN/CSA 22.2 No. 60950-1, Second Edition
● TUV/GS to EN 60950-1, Second Edition
● CB to IEC 60950-1 Second Edition with all country deviations
● CE Marking
● NOM (through partners and distributors)
Electromagnetic emissions certifications
● FCC Part 15 Class A
● EN 55022 Class A (CISPR22)
● EN 55024 (CISPR24)
● AS/NZS CISPR22 Class A
● CE
● CNS13438 Class A
● MIC
● GOST
© 2011 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 13 of 17
Description
Specification
● China EMC Certifications
Environmental
Reduction of Hazardous Substances (ROHS) 5
Telco
Common Language Equipment Identifier (CLEI) code
Warranty
Limited lifetime warranty
Cisco Limited Lifetime Hardware Warranty
Cisco Catalyst 2960-S and 2960 Series Switches come with a limited lifetime warranty (Table 8). The warranty for
the Catalyst 2960-S has the same terms as our standard limited lifetime warranty plus the addition of next
business day delivery of replacement hardware where available and 90 days of 8x5 Cisco Technical Assistance
(TAC) support. Your formal warranty statement, including the warranty applicable to Cisco software, appears in the
Cisco information packet that accompanies your Cisco product. We encourage you to review carefully the
warranty statement shipped with your specific product before use.
Cisco reserves the right to refund the purchase price as its exclusive warranty remedy.
For further information on warranty terms, visit http://www.cisco.com/go/warranty.
Table 8.
Limited Lifetime Warranty Terms
Cisco Limited Lifetime Hardware Warranty
Cisco Enhanced Limited Lifetime Hardware Warranty
Device covered
Applies to Cisco Catalyst 2960 Series Switches sold on or
after May 1, 2009
Applies to Cisco Catalyst 2960-S Series Switches
Warranty duration
As long as the original end user continues to own or use
the product, provided that: fan and power supply warranty
is limited to five (5) years.
As long as the original end user continues to own or use the
product, provided that: fan and power supply warranty is
limited to five (5) years.
End-of-life policy
In the event of discontinuance of product manufacture,
Cisco warranty support is limited to five (5) years from the
announcement of discontinuance.
In the event of discontinuance of product manufacture, Cisco
warranty support is limited to five (5) years from the
announcement of discontinuance.
Hardware replacement Cisco or its service center will use commercially
reasonable efforts to ship a replacement part within ten
(10) working days after receipt of the RMA request. Actual
delivery times may vary depending on customer location.
Cisco or its service center will use commercially reasonable
efforts to ship a Catalyst 2960-S replacement for next
business day delivery, where available. Otherwise, a
replacement will be shipped within ten (10) working days
after receipt of the RMA request. Actual delivery times may
vary depending on customer location.
Effective date
Hardware warranty commences from the date of shipment
to customer (and in case of resale by a Cisco reseller, not
more than ninety [90] days after original shipment by
Cisco).
Hardware warranty commences from the date of shipment to
customer (and in case of resale by a Cisco reseller, not
more than ninety [90] days after original shipment by Cisco).
TAC support
Not included.
Cisco will provide, during customer’s local business hours, 8
hours per day, 5 days per week basic configuration,
diagnosis, and troubleshooting of device-level problems for
up to 90 days from the date of shipment of the originally
purchased Catalyst 2960-S product. This support does not
include solution or network-level support beyond the specific
device under consideration.
Cisco.com Access
Warranty allows guest access only to Cisco.com
Warranty allows guest access only to Cisco.com
Software Update Policy for Cisco Catalyst 2960-S and 2960 Series Switches with LAN Lite Software
Customers with Cisco Catalyst LAN Lite software licenses will be provided with maintenance updates and bug
fixes designed to maintain the compliance of the software with published specifications, release notes, and
industry standards compliance as long as the original end user continues to own or use the product or for up to
one year from the end-of-sale date for this product, whichever occurs earlier. Customers with licenses for our
premium software images, Enterprise Services or IP Services, require a service support contract such as Cisco
®
SMARTnet Service to download updates.
© 2011 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 14 of 17
This policy supersedes any previous warranty or software statement and is subject to change without notice.
Cisco and Partner Services for the Catalyst 2960 Switches
Minimize operating costs and reduce power consumption for the Cisco Catalyst 2960 switch using intelligent,
personalized services from Cisco and our partners. Through a discovery process that begins with understanding
your business objectives, we help you integrate the Cisco Catalyst switch into your architecture and incorporate
network services onto it. Sharing knowledge and leading practices, we support your success every step of the way
as you deploy, absorb, manage, and scale new technology. Choose from a flexible suite of support services
designed to meet your business needs and help you maintain high-quality network performance while controlling
operational costs. Table 9 lists the technical services available for the Cisco Catalyst 2960-S and 2960 Series
Switches.
Table 9.
Technical Services Available for Cisco Catalyst 2960-S and 2960 Series Switches
Technical Services
Cisco SMARTnet® Service
● Around-the-clock, global access to the Cisco TAC
● Unrestricted access to the extensive Cisco.com knowledge base and tools
● Next-business-day, 8x5x4, 24x7x4, or 24x7x2 advance hardware replacement and onsite parts replacement and installation available1
● Ongoing operating system software updates within the licensed feature set2
● Proactive diagnostics and real-time alerts on Smart Call Home enabled devices
Cisco Smart Foundation Service
● Next-business-day advance hardware replacement as available
● Access to SMB TAC during business hours (access levels vary by region)
● Access to Cisco.com SMB knowledge base
● Online technical resources through the Smart Foundation Portal
● Operating system software bug fixes and patches
Cisco Smart Care Service
● Network-level coverage for the needs of small and medium-sized businesses
● Proactive health checks and periodic assessments of Cisco network foundation, voice, and security technologies
● Technical support for eligible Cisco hardware and software through Smart Care Portal
● Cisco operating system and application software updates and upgrades2
● Next-business-day advance hardware replacement as available, 24x7x4 option available1
Cisco SP Base Service
● Around-the-clock, global access to the Cisco TAC
● Registered access to Cisco.com
● Next business day, 8x5x4, 24x7x4, and 24x7x2 advance hardware replacement. Return to factory option available1
● Ongoing operating system software updates2
Cisco Focused Technical Support Services
Three levels of premium, high-touch services are available:
● Cisco High-Touch Operations Management Service
● Cisco High-Touch Technical Support Service
● Cisco High-Touch Engineering Service
Valid Cisco SMARTnet or SP Base contracts are required on all network equipment.
Footnotes:
1. Advance hardware replacement is available in various service-level combinations. For example, 8x5xNBD indicates that
shipment will be initiated during the standard 8-hour business day, 5 days a week (the generally accepted business days within
the relevant region), with next-business-day (NBD) delivery. Where NBD is not available, same day shipping is provided.
Restrictions apply; please review the appropriate service descriptions for details.
2. Cisco operating system updates include the following: maintenance releases, minor updates, and major updates within the
licensed feature set.
© 2011 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 15 of 17
Ordering Information
Table 10 has ordering information for the Cisco Catalyst 2960-S and 2960 Series Switches with LAN Lite
Software.
Table 10.
Ordering Information for Cisco Catalyst 2960 Series Switches with LAN Lite Software
Part Numbers
Cisco Catalyst 2960S-48TS-S
Description
● 48 Ethernet 10/100/1000
● 2 One Gigabit Ethernet SFP uplink ports
● LAN Lite software
Cisco Catalyst 2960S-24TS-S
● 24 Ethernet 10/100/1000
● 2 One Gigabit Ethernet SFP uplink ports
● LAN Lite software
WS-C2960-8TC-S
● 8 Ethernet 10/100 ports and 1 dual-purpose uplink (dual-purpose uplink port has 1 10/100/1000
Ethernet port and 1 SFP-based Gigabit Ethernet port, 1 port active)
● LAN Lite software
● Compact size with no fan; mounting magnet included
WS-C2960-24-S
● 24 Ethernet 10/100 ports
● LAN Lite software
WS-C2960-24TC-S
● 24 Ethernet 10/100 ports and 2 dual-purpose uplinks (each dual-purpose uplink port has 1
10/100/1000 Ethernet port and 1 SFP-based Gigabit Ethernet port, 1 port active)
● LAN Lite software
WS-2960-24PC-S
● 24 Ethernet 10/100 ports and 2 dual-purpose uplinks (each dual-purpose uplink port has 1
10/100/1000 Ethernet port and 1 SFP-based Gigabit Ethernet port, 1 port active)
● LAN Lite software
● 24 PoE ports
WS-2960-24LC-S
● 24 Ethernet 10/100 ports and 2 dual-purpose uplinks (each dual-purpose uplink port has 1
10/100/1000 Ethernet port and 1 SFP-based Gigabit Ethernet port, 1 port active) ]
● LAN Lite software
● 8 PoE ports
WS-C2960-48TT-S
● 48 Ethernet 10/100 ports and 2 10/100/1000 TX uplinks
● LAN Lite software
WS-C2960-48TC-S
● 48 Ethernet 10/100 ports and 2 dual-purpose uplinks (each dual-purpose uplink port has 1
10/100/1000 Ethernet port and 1 SFP-based Gigabit Ethernet port, 1 port active)
● LAN Lite software
WS-2960-48PST-S
● 48 Ethernet 10/100 ports and 2 10/100/1000 uplinks and 2 SFP uplinks
● LAN Lite software
● 48 PoE ports
Spare Rack-Mount Kits for the Cisco Catalyst 2960 Series Switches with LAN Lite Software
RCKMNT-1RU=
● Spare rack-mount kit for the Cisco Catalyst 2960 and 2960-S Series
RCKMNT-REC-1RU=
● 1 RU recessed rack-mount kit for the Cisco Catalyst 2960 and 2960-S Series
Power Cords
CAB-16AWG-AC
AC Power cord, 16AWG
CAB-ACE
AC Power Cord (Europe), C13, CEE 7, 1.5M
CAB-L620P-C13-US
Power Cord, 250VAC, 15A, NEMA L6-20 to C13, US
CAB-ACI
AC Power Cord (Italy), C13, CEI 23-16, 2.5m
CAB-ACU
AC Power Cord (UK), C13, BS 1363, 2.5m
CAB-ACA
AC Power Cord (China/Australia), C13, AS 3112, 2.5m
CAB-ACS
AC Power Cord (Switzerland), C13, IEC 60884-1, 2.5m
CAB-ACR
AC Power Cord (Argentina), C13, EL 219 (IRAM 2073), 2.5m
© 2011 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 16 of 17
Part Numbers
Description
CAB-ACC
CORD,PWR,CHINA,10A,IEC 320,C13(APN=CS-PWR-CH)
CAB-3P-JPN
CABASY,POWER CORD,JAPAN 3P, PSE, 12A @125VAC
CAB-L620P-C13-JPN
Power Cord, 250VAC, 15A, NEMA L6-20 to C13, JAPAN
CAB-IND-10A
Power cable for India
CAB-AC15A-90L-US
15A AC Pwr Cord, left-angle (United States)
CAB-ACE-RA
Power Cord Europe, Right Angle
CAB-ACI-RA
Power Cord-Italian, Right Angle
CAB-ACU-RA
Power Cord UK, Right Angle
CAB-ACC-RA
Power Cord China, Right Angle
CAB-ACA-RA
Power Cord, Australian, Right Angle
CAB-ACS-RA
Power Cord for Switzerland, Right Angle
CAB-ACR-RA
Power Cord, Argentina, Right Angle
CAB-JPN-RA
Power Cord, Japan, Right Angle
Optical Transceivers for the Cisco Catalyst 2960 Series Switches with LAN Lite Software
GLC-LH-SM=
1000BASE-LX/LH SFP transceiver module for MMF and SMF, 1300-nm wavelength
GLC-SX-MM=
1000BASE-SX SFP transceiver module for MMF, 850-nm wavelength
GLC-T=
1000BASE-T SFP transceiver module for Category 5 copper wire
GLC-GE-100FX=
100BASE-FX SFP module for Gigabit Ethernet ports, 1310-nm wavelength, 2 km over MMF
GLC-FE-100FX=
100BASE-FX SFP module for 100-Mb ports, 1310-nm wavelength, 2 km over MMF
CAB-SM-LCSC-1M
1m fiber single-mode LC-to-SC connectors
CAB-SM-LCSC-5M
5m fiber single-mode LC-to-SC connectors
For latest information on transceivers, please go to:
http://www.cisco.com/en/US/products/hw/modules/ps5455/products_device_support_tables_list.html.
For more information about Cisco products, contact:
●
United States and Canada: (toll free) 800 553-NETS (6387)
●
Europe: 32 2 778 4242
●
Australia: 612 9935 4107
●
Other: 408 526-7209
●
World Wide Web URL: http://www.cisco.com
Printed in USA
© 2011 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
C78-423870-06
06/11
Page 17 of 17