MICROWAVE OVEN
CE101KR
SERVICE
Manual
CONTENTS
MICROWAVE OVEN
1. Precaution
2. Specifications
3. Operating Instructions
4. Disassembly and Reassembly
DRINKS
PREHEAT
OVEN/ C
QUICHE
GRILL
RICE/PASTA
5. Alignment and Adjustments
MW+OVEN
GRATIN
MW+GRILL
AUTO REHEAT / COOK
BURGER/FISH FINGER
BAKED POTATOES
1. PLATED MEAL
2. CANNED FOOD
3. CASSEROLE / STEW
4. SOUP / SAUCE
5. BOILED POTATOES
6. FRESH VEGETABLES
7. FISH
8. ROAST BEEF
9. ROAST PORK
10.ROAST CHICKEN
AUTO DEFROST
AUTO REHEAT / COOK
Plus/min +
Minus/min -
h
10min
MICROWAVE
POWER LEVEL
min
Dish
1min
1kg
10s
0.1kg
CLOCK
MEMORY
6. Troubleshooting
CE101K
7. Exploded Views and Parts List
8. PCB Diagrams
9. Schematic Diagrams
BWT
PRECAUTIONS TO BE OBSERVED BEFORE AND DURING
SERVICING TOAVOID POSSIBLE EXPOSURE TO EXCESSIVE
MICROWAVE ENERGY
(a) Do not operate or allow the oven to be
operated with the door open.
(b) Make the following safety checks on
all ovens to be serviced before
activating the magnetron or other
microwave source, and make repairs as
necessary:
(1) Interlock operation,
(2) proper door closing,
(3) seal and sealing surfaces (arcing,
wear, and other damage),
(4) damage to or loosening of hinges
and latches,
(5) evidence of dropping or abuse.
(c) Before turning on microwave power
for any service test or inspection
within the microwave generating
compartments, check the magnetron,
wave guide or transmission line, and
cavity for proper alignment, integrity,
and connections.
(d) Any defective or misadjusted
components in the interlock, monitor,
door seal, and microwave generation
and transmission systems shall be
repaired, replaced, or adjusted by
procedures described in this manual
before the oven is released to the
owner.
(e) A Microwave leakage check to verify
compliance with the Federal
performance standard should be
performed on each oven prior to
release to the owner.
Samsung Electronics
1. Precaution
Follow these special safety precautions. Although the microwave oven is completely safe during ordinary
use, repair work can be extremely hazardous due to possible exposure to microwave radiation, as well as
potentially lethal high voltages and currents.
1-1 Safety precautions (
)
1. All repairs should be done in accordance
with the procedures described in this
manual. This product complies with
Federal Performance Standard 21 CFR
Subchapter J (DHHS).
2. Microwave emission check should be
performed to prior to servicing if the oven is
operative.
3. If the oven operates with the door open :
Instruct the user not to operate the oven and
contact the manufacturer and the center for
devices and radiological health immediatly.
4. Notify the Central Service Center if the
microwave leakage exceeds 5 mW/cm2
5. Check all grounds.
6. Do not power the MWO from a "2-prong"
AC cord. Be sure that all of the built-in
protective devices are replaced. Restore any
missing protective shields.
7. When reinstalling the chassis and its
assemblies, be sure to restore all protective
devices, including: nonmetallic control
knobs and compartment covers.
8. Make sure that there are no cabinet openings
through which people--particularly
children--might insert objects and contact
dangerous voltages. Examples: Lamp hole,
ventilation slots.
9. Inform the manufacturer of any oven found
to have emmission in excess of 5 mW/cm2,
Make repairs to bring the unit into
compliance at no cost to owner and try to
determine cause.
Instruct owner not to use oven until it has
been brought into compliance.
CENTRAL SERVICE CENTER
10. Service technicians should remove their
watches while repairing an MWO.
Samsung Electronics
11. To avoid any possible radiation hazard,
replace parts in accordance with the wiring
diagram. Also, use only the exact
replacements for the following parts:
Primary and secondary interlock switches,
interlock monitor switch.
12. If the fuse is blown by the Interlock Monitor
Switch: Replace all of the following at the
same time: Primary and secondary switches,
as well as the Interlock Monitor Switch. The
correct adjustment of these switches is
described elsewhere in this manual. Make
sure that the fuse has the correct rating for
the particular model being repaired.
13. Design Alteration Warning:
Use exact replacement parts only, i.e.,
only those that are specified in the
drawings and parts lists of this manual.
This is especially important for the
Interlock switches, described above.
Never alter or add to the mechanical or
electrical design of the MWO. Any design
changes or additions will void the
manufacturer's warranty.10.Always unplug
the unit's AC power cord from the AC
power source before attempting to
remove or reinstall any component or
assembly.
14. Never defeat any of the B+ voltage
interlocks. Do not apply AC power to the
unit (or any of its assemblies) unless all
solid-state heat sinks are correctly installed.
15. Some semiconductor ("solid state") devices
are easily damaged by static electricity. Such
components are called Electrostatically
Sensitive Devices (ESDs). Examples include
integrated circuits and field-effect
transistors.
Immediately before handling any
semiconductor components or assemblies,
drain the electrostatic charge from your
body by touching a known earth ground.
16. Always connect a test instrument's ground
lead to the instrument chassis ground before
connecting the positive lead; always remove
the instrument's ground lead last.
1-1
Pretaution
1-2 Special Servicing Precautions (Continued)
17. When checking the continuity of the
switches or transformer, always make sure
that the power is OFF, and one of the lead
wires is disconnected.
18. Components that are critical for safety are
indicated in the circuit diagram by
shading,
or
.
19. Use replacement components that have the
same ratings, especially for flame resistance
and dielectric strength specifications. A
replacement part that does not have the
same safety characteristics as the original
might create shock, fire or other hazards.
1-3 Special High Voltage Precautions
1. High Voltage Warning
Do not attempt to measureany of the high
voltages--this includes the filament voltage
of the magnetron. High voltage is present
during any cook cycle.
Before touching any components or wiring,
always unplug the oven and discharge the
high voltage capacitor (See Figure 1-1)
2. The high-voltage capacitor remains charged
about 30 seconds after disconnection. Short
the negative terminal of the high-voltage
capacitor to the oven chassis. (Use a
screwdriver.)
3. High voltage is maintained within specified
limits by close-tolerance, safety-related
components and adjustments. If the high
voltage exceeds the specified limits, check
each of the special components.
¢
: Touch chassis side first then short to the high voltage
capacitor terminal by using a screwdriver or jumper
wire.
PRECAUTION
There exists HIGH VOLTAGE ELECTRICITY with high
current capabilities in the circuits of the HIGH VOLTAGE
TRANSFORMER secondary and filament terminals. It is
extremely dangerous to work on or near these circuits
with the oven energized.
DO NOT measure the voltage in the high voltage circuit
including filament voltage of magnetron.
1-2
PRECAUTION
Never touch any circuit wiring with your hand nor with an
insulated tool during operation.
PRECAUTION
Servicemen should remove their watches whenever
working close to or replacing the magnetron.
Samsung Electronics
2. Specifications
2-1 Table of Specifications
MODEL
ITEM
CE101KR
TIMER
99 MINUTES 90 SECONDS
POWER SOURCE
230V/50HZ, AC
POWER CONSUMPTION
MICROWAVE : 1,500W
OUTPUT POWER
FROM90 TO 900W (10 LEVEL POWER)
(IEC-705 TEST PROCEDURE)
OPERATING FREQUENCY
2,450MHz
MAGNETRON
OM75P(31)
COOLING METHOD
COOLING FAN MOTOR
OUTSIDE DIMENSIONS
547(W) x 339(H) x 487(D)
NET WEIGHT
25 Kg
SHIPPING WEIGHT
29 Kg
2-2 Comparison Chart
MODEL
Samsung Electronics
CE101KR
MORE/LESS
¡
AUTO COOK/DISH
¡
AUTO DEFROST
¡
TIME COOK
¡
POWER LEVEL
¡
CONVECTION
¡
GRILL
¡
MICROWAVE+CONVECTION
¡
MICROWAVE+GRILL
¡
2-1
3. Operating Instructions
3-1 Control Panel
DRINKS
PREHEAT
OVEN/ C
QUICHE
GRILL
RICE/PASTA
MW+OVEN
GRATIN
MW+GRILL
AUTO REHEAT / COOK
BURGER/FISH FINGER
1. PLATED MEAL
2. CANNED FOOD
3. CASSEROLE / STEW
4. SOUP / SAUCE
5. BOILED POTATOES
6. FRESH VEGETABLES
7. FISH
8. ROAST BEEF
9. ROAST PORK
10.ROAST CHICKEN
BAKED POTATOES
AUTO DEFROST
h
POWER LEVEL
AUTO REHEAT / COOK
Plus/min +
Minus/min -
10min
MICROWAVE
min
Dish
1min
1kg
10s
0.1kg
CLOCK
MEMORY
CE101K
3-2 Features & External Views
Door
Ventilation Slot
Light
Safety Interlock Holes
DRINKS
PREHEAT
OVEN/ C
Door Latches
,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,
QUICHE
GRILL
RICE/PASTA
MW+OVEN
GRATIN
MW+GRILL
AUTO REHEAT / COOK
BURGER/FISH FINGER
BAKED POTATOES
1. PLATED MEAL
2. CANNED FOOD
3. CASSEROLE / STEW
4. SOUP / SAUCE
5. BOILED POTATOES
6. FRESH VEGETABLES
7. FISH
8. ROAST BEEF
9. ROAST PORK
10.ROAST CHICKEN
AUTO DEFROST
10min
Control Panel
AUTO REHEAT / COOK
Plus/min +
Minus/min -
h
MICROWAVE
POWER LEVEL
min
Dish
1min
1kg
10s
0.1kg
CLOCK
MEMORY
CE101K
Open Door Push Button
Glass Plate
Guide Roller
DRINKS
PREHEAT
OVEN/ C
QUICHE
GRILL
RICE/PASTA
MW+OVEN
GRATIN
MW+GRILL
BAKED POTATOES
1. PLATED MEAL
2. CANNED FOOD
3. CASSEROLE / STEW
4. SOUP / SAUCE
5. BOILED POTATOES
6. FRESH VEGETABLES
7. FISH
8. ROAST BEEF
9. ROAST PORK
10.ROAST CHICKEN
AUTO DEFROST
AUTO REHEAT / COOK
Plus/min +
Minus/min -
h
10min
MICROWAVE
POWER LEVEL
339mm
AUTO REHEAT / COOK
BURGER/FISH FINGER
min
Dish
1min
1kg
10s
0.1kg
CLOCK
MEMORY
CE101K
225mm
547mm
Samsung Electronics
487mm
3-1
4. Disassembly and Reassembly
4-1 Replacement of Magnetron, Motor Assembly and Lamp
Remove the magnetron including the shield case,
permanent magnet, choke coils and capacitors (all
of which are contained in one assembly).
1. Disconnect all lead wires from the magnetron
and lamp.
2. Remove the bracket mounting.
3.Remove the magnetron supporter
4. Remove the air cover.
5. Remove screws securing the magnetron to the
wave guide.
6. Take out the magnetron very carefully.
7. Remove screws from the back panel.
8.Remove the assy noise filter.
9. Take out the fan motor.
10. Remove the oven lamp by pulling out from
hole of air cover carefully.
NOTE1: When removing the magnetron, make
sure that its antenna does not hit any
adjacent parts, or it may be damaged.
NOTE2: When replacing the magnetron, be sure
to remount the magnetron gasket in
the correct position and make sure the
gasket is in good condition.
Cover Air
Thermo S/W
Lamp
Fan Motor
Magnetron H. V. Trans
H. V. Capacitor
Screw
4-2 Replacement of High Voltage Transformer
1. Discharge the high voltage capacitor.
2. Disconnect all the leads.
3. Remove the mounting bolts.
4. Reconnect the leads correctly and firmly.
H. V. Trans
Screws
Samsung Electronics
4-1
Disassembly and Reassembly
4-3 Replacement of Door Assembly
4-3-1 Removal of Door Assembly
Remove screws securing the upper hinge and
lower hinge. Then remove the door assembly.
Upper Hinge
Screw
Lower Hinge
Screw
4-3-2 Removal of Door "C"
Insert flat screwdriver into the gap between Door
"A" and Door "C" to remove Door "C". Be careful
when handling Door "C" because it is fragile.
Door "A"
Door "C"
4-3-3 Removal of Door "E"
Following the procedure as shown in the figure,
insert and bend a thin metal plate between Door
"E" and Door "A" until you hear the 'tick' sound.
Door "E"
1. Insertion depth of the thin metal plate should be
0.5mm or less.
4-3-4 Removal of Key Door & Spring
Remove pin hinge from Door "E"
Detach spring from Door "E" and key door.
Door "E"
Spring
Key Door
4-2
Samsung Electronics
Disassembly and Reassembly
4-3-5 Reassembly Test
After replacement of the defective component parts of the door, reassemble it and follow the instructions below for proper
installation and adjustment so as to prevent an excessive microwave leakage.
1. When mounting the door to the oven, be sure to adjust the door parallel to the bottom line of the oven
face plate by moving the upper hinge and lower hinge in the direction necessary for proper alignment.
2. Adjust so that the door has no play between the inner door surface and oven front surface. If the door
assembly is not mounted properly, microwave energy may leak from the space between the door and
oven.
3. Do the microwave leakage test.
4-4 Replacement of Fuse
1. Disconnect the oven from the power source.
2. Remove the 10A fuse in the Noise filter.
3. When replacing the 10A fuse, be sure to use an
exact replacement part. If new 10A fuse blows
out again after replacement, check the primary
interlock switch, door sensing switch and
interlock monitor switch.
4. When the above three switches operate properly,
check if any other part such as the control circuit
board, blower motor or high voltage
transformer is defective.
4-5 Replacement of Drive Motor
1. Take out the glass tray and guide roller from the
cavity.
2. Turn the oven upside down to replace the drive motor.
3. Remove a screw securing the drive motor cover.
Drive Motor
Screw
4. Disconnect all the lead wires from the drive motor.
5. Remove screws securing the drive motor to the
cavity.
6. Remove the drive motor and coupler.
Thermo
Switch
7. When replacing the drive motor, be sure to
remount it in the correct position with the
coupler.
8. Connect all the leads to the drive motor.
Drive Motor Cover
Base Plate
9. Screw the drive motor cover to the base plate
with a screw driver.
Samsung Electronics
4-3
Disassembly and Reassembly
4-6 Replacement of Control Circuit Board
4-6-1 Removal of Control Box Assembly
1. Be sure to ground any static electric charge in
your body and never touch the control circuit.
2. Disconnect the connectors from the control
circuit board.
Screw
3. Remove screws securing the control box
assembly.
4. Remove the screw securing the ground tail of
the keyboard.
Control Box
4-6-2 Removal of P.C.B Assembly
1. Pull the lever end of the plastic fastener and
remove the Flexible Printed Circuit(FPC) of
membrane panel.
2. Remove screws securing the control circuit
board.
FPC Connector
Screw
3. Lift up the control circuit board from the Ass'y
control box.
4. When reconnecting the FPC connector, make
sure that the holes on the connector are properly
engaged with the hooks on the Plastic Fastener.
4-6-3 Removal of Window Display & Membrane Panel
1. Window display should not be disassembled as
its mounting tabs will be broken. If repair work
is difficult, replace with Ass'y control panel.
2. The membrane key board is attached to the
escutcheon base with doublefaced adhesive
tape. Therefore, applying hot air such as using
of hair dryer is recommended for smoother
removal.
3. When installing new membrane key board,
make sure that the surface of escutcheon base is
cleaned sufficiently so that any problems
(shorted contacts or uneven surface) can be
avoided.
4-4
Window
Display
Membrane
Panel
Samsung Electronics
5. Alignment and Adjustments
PRECAUTION
1. High voltage is present at the high voltage terminals during any cook cycle.
2. It is neither necessary nor advisable to attempt measurement of the high voltage.
3. Before touching any oven components or wiring, always unplug the oven from its power source and discharge the high voltage
capacitor.
5-1 High Voltage Transformer
1. Remove connectors from the transformer terminals
and check continuity.
2. Normal resistance readings are as follows:
MODEL
Secondary
Filament
Primary
Filament Terminals
CE101KR
94Ω ¡ 10%
Shows Continuity
1.7Ω ¡ 10%
(Room temperature = 20ûC)
Primary
Terminals
5-2 Low Voltage Transformer
1. The low voltage transformer is located on the
control circuit board.
2. Remove the low voltage transformer from the
PCB Ass'y and check continuity.
3. Normal resistor reading is shown in the table.
Terminals
1~2(Input)
3~4(Output)
5~6(Output)
Resistance
195.4Ω
1.50Ω
0.73Ω
5-3 Magnetron
Continuity checks can indicate only an open
filament or a shorted magnetron. To diagnose an
open filament or shorted magnetron :
1. Isolate the magnetron from the circuit by
disconnecting its leads.
2. A continuity check across the magnetron filament
terminals should indicate one ohm or less.
3. A continuity check between each filament terminal
and magnetron case should read open.
Magnetron Antenna
Gasket Plate
Cooling Fins
Samsung Electronics
5-1
Alignment and Adjustments
5-4 High Voltage Capacitor
1. Check continuity of the capacitor with the meter set at the highest resistance scale.
2. Once the capacitor is charged, a normal capacitor shows continuity for a short time, and then indicates 9MΩ.
3. A shorted capacitor will show continuous continuity.
4. An open capacitor will show constant 9MΩ.
5. Resistance between each terminal and chassis should read infinite.
5-5 High Voltage Diode
1. Isolate the diode from the circuit by disconnecting its leads.
2. With the ohm-meter set at the highest resistance scale, measure across the diode terminals. Reverse the
meter leads and read the resistance. A meter with 6V, 9V or higher voltage batteries should be used to
check the front-to back resistance of the diode (otherwise an infinite resistance may be read in both
directions). The resistance of a normal diode will be infinite in one direction and several hundred KΩ in
the other direction.
5-6 Main Relay and Power Control Relay
1. The relays are located on the PCB Ass'y. Isolate them from the main circuit by disconnecting the leads.
2. Operate the microwave oven with a water load in the oven. Set the power level set to high.
3. Check continuity between terminals of the relays after the start pad is pressed.
5-7 Adjustment of Primary Switch, Door Sensing Switch and Monitor Switch
Precaution
For continued protection against radiation hazard, replace parts in accordance with the wiring diagram and be sure to use the
correct part number for the following switches: Primary and door sensing switches, and the interlock monitor switch (replace all
together). Then follow the adjustment procedures below. After repair and adjustment, be sure to check the continuity of all
interlock switches and the interlock monitor switch.
1. When mounting Primary switch and Interlock
Monitor switch to Latch Body, consult the
figure.
Primary Interlock S/W
NOTE:No specific adjustment during
installation of Primary switch and Monitor
switch to the latch body is necessary.
2. When mounting the Latch Body to the oven
assembly, adjust the Latch Body by moving it so
that the oven door will not have any play in it.
Check for play in the door by pulling the door
assembly. Make sure that the latch keys move
smoothly after adjustment is completed.
Completely tighten the screws holding the Latch
Body to the oven assembly.
3. Reconnect to Monitor switch and check the
continuity of the monitor circuit and all latch
switches again by following the components test
procedures.
4. Confirm that the gap between the switch
housing and the switch actuator is no more than
0.5mm when door is closed.
5-2
Lever Switch(A)
Door Sensing S/W
Interlock Monitor S/W
Lever Switch(B)
Body Latch
Key Door
Primary switch
Monitor switch (COM-NC)
Monitor switch (COM-NO)
Door Sensing switch
Door Open
∞
0
∞
∞
Door Closed
0
∞
0
0
Samsung Electronics
Alignment and Adjustments
5-8 Output Power of Magnetron
CAUTION
MICROWAVE RADIATION
PERSONNEL SHOULD NOT ALLOW EXPOSURE TO MICROWAVE RADIATION FROM MICROWAVE GENERATOR OR OTHER PARTS
CONDUCTING MICROWAVE ENERGY.
The output power of the magnetron can be measured by performing a water temperature rise test.
Equipment needed :
* Two 1-liter cylindrical borosilicate glass vessel (Outside diameter 190 mm)
* One glass thermometer with mercury column
NOTE: Check line voltage under load. Low voltage will lower the magnetron output. Make all temperature
and time tests with accurate equipment.
1. Fill the one liter glass vessel with water.
2. Stir water in glass vessel with thermometer, and record glass vessel's temperature ("T1", 10±1ûC).
3. After moving the water into another glass vessel, place it in the center of the cooking tray. Set the oven to high
power and operate for 48seconds exactly. (1.5 seconds included as a holding time of magnetron oscillation:)
4. When heating is finished, stir the water again with the thermometer and measure the temperature ("T2").
5. Subtract T1 from T2. This will give you the water temperature rise. (∆T)
6. The output power is obtained by the following formula;
Output Power =
4.187 x 1000 x ∆T+0.88xMcx(T2-T0)
46.5
46.5: Heating Time (sec)
4.187 : Coefficient for Water
1000 : Water (cc)
∆T : Temperature Rise (T2-T1)
Mc : Cylindrical borosilicate glass weight
To : Room temperature.
7. Normal temperature rise for this model is 9ûC to 11ûC at 'HIGH'.
NOTE 1: Variations or errors in the test procedure will cause a variance in the temperature rise.
Additional power test should be made if temperature rise is marginal.
NOTE 2: Output power in watts is computed by multiplying the temperature rise (step 5) by a factor of 90
times the of centigrade temperature.
5-9 Microwave Heat Distribution - Heat Evenness
The microwave heat distribution can be checked indirectly by measuring the water temperature rise at
certain positions in the oven:
1. Prepare five beakers made of 'Pyrex', having 100 milliliters capacity each.
2. Measure exactly 100milliliters off water load with a measuring cylinder, and pour into each beaker.
3. Measure the temperature of each water load. (Readings shall be taken to the first place of decimals.)
4. Put each beaker in place on the cooking tray as illustrated in figure below. Start heating.
5. After heating for 2 minutes, measure the water temperature in each beaker.
6. Microwave heat distribution rate can be calculated as follows:
Heat Distribution =
Minimum
Temperature Rise
Maximum
Temperature Rise
D
X 100(%)
Beaker
D
The result should exceed 65%.
D/4
D/4
D/4
D/4
Samsung Electronics
Cooking Tray
5-3
Alignment and Adjustments
5-10 Procedure for Measurement of Microwave Energy Leakage
1) Pour 275¡ 15cc of 20¡ 5¡ ( 68¡ 9¢ ) water in a
beaker which is graduated to 600cc, and place
the beaker in the center of the oven.
2) Start to operate the oven and measure the
leakage by using a microwave energy survey
meter.
3) Set survey meter with dual ranges to 2,450MHz.
4) When measuring the leakage, always use the 2
inch spacer cone with the probe. Hold the probe
perpendicular to the cabinet door. Place the
spacer cone of the probe on the door and/or
cabinet door seam and move along the seam, the
door viewing window and the exhaust openings moving the probe in a clockwise direction at a rate of 1
inch/sec. If the leakage testing of the cabinet door seam is taken near a corner of the door, keep the probe
perpendicular to the areas making sure that the probe end at the base of the cone does not get closer than 2
inches to any metal. If it gets closer than 2 inches, erroneous readings may result.
5) Measured leakage must be less than 4mW/cm2, after repair or adjustment.
AUTO REHEAT / COOK
1. PLATED MEAL
2. CANNED FOOD
3. CASSEROLE / STEW
4. SOUP / SAUCE
5. BOILED POTATOES
6. FRESH VEGETABLES
7. FISH
8. ROAST BEEF
9. ROAST PORK
10.ROAST CHICKEN
Maximum allowable leakage is 5mW/cm2.
4mW/cm2 is used to allow for measurement and meter accuracy
5-11 Check for Microwave Leakage
1. Remove the outer panel.
2. Pour 275±15cc of 20±5ûC(68±9ûF) water in a
beaker which is graduated to 600cc, and
place the beaker in the center of the oven.
3. Start the oven at the highest power level.
4. Set survey meter dual ranges to 2,450MHz.
5. Using the survey meter and spacer cone as
described above, measure arnear the
opening of magnetron, the surface of the air
guide and the surface of the wave guide as
shown in the following photo.( but avoid the
high voltage components.) The neading
should be less than 4mW/cm2.
WARNING
AVOID THE HIGH VOLTAGE COMPONENTS.
5-12. Note on Measurement
1) Do not exceed the limited scale.
2) The test probe must be held on the grip of the handle, otherwise a false reading may result when the
operator's hand is between the handle and the probe.
3) When high leakage is suspected, do not move the probe horizontally along the oven surface; this may
cause damage to the probe.
4) Follow the recommendation of the manufacturer of the microwave energy survey meter.
5-13 Leakage Measuring Procedure
5-13-1 Record keeping and notification after measurement
1) After adjustment and repair of a radiarion preventing device, make a repair record for the measured
values, and keep the data.
2) If the radiation leakage is more than 4 mW/§† after determining that all parts are in good condition,
functioning properly and the identical parts are replaced as listed in this manual notift that fact to ;
CENTRAL SERVICE CENTER
5-13-2 At least once a year have the microwave energy survey meter checked for accuracy by its
manufacturer.
5-4
Samsung Electronics
6. Troubleshooting
PRECAUTION
1. CHECK GROUNDING BEFORE CHECKING FOR TROUBLE.
2. BE CAREFUL OF THE HIGH VOLTAGE CIRCUIT.
3. DISCHARGE THE HIGH VOLTAGE CAPACITOR.
4. WHEN CHECKING THE CONTINUITY OF THE SWITCHES OR TRANSFORMER, DISCONNECT ONE LEAD WIRE FROM THESE
PARTS AND THEN CHECK CONTINUITY WITHOUT THE POWER SOURCE ON. TO DO OTHERWISE MAY RESULT IN A FALSE
READING OR DAMAGE TO YOUR METER.
5. DO NOT TOUCH ANY PART OF THE CIRCUIT OR THE CONTROL CIRCUIT BOARD, SINCE STATIC DISCHARGE MAY DAMAGE IT.
ALWAYS TOUCH GROUND WHILE WORKING ON IT TO DISCHARGE ANY STATIC CHARGE BUILT UP.
6-1 Electrical Malfunction
SYMPTOM
CAUSE
CORRECTIONS
Oven is dead.
1. Open or loose lead wire harness
Fuse is OK.
2. Open thermal cutout (Magnetron)
No display and no operation at all. 3. Open low voltage transformer
4. Defective Ass'y PCB
Check fan motor when thermal cutout is defective.
No display and no operation at all. 1. Shorted lead wire harness
Fuse is blown.
2. Defective primary latch switch (NOTE 1)
3. Defective monitor switch (NOTE1)
4. Shorted HVCapacitor
5. Shorted HVTransformer (NOTE2)
Check adjustment of primary, interlock monitor,
door sensing switch.
Check Ass'y PCB when LVT is defective.
NOTE 1: All of these switches must be replaced at the same time.
(refer to adjustment instructions)
Check continuity of power relay contacts and if it has continuity, replace power
relay also.
NOTE 2: When HVTransformer is replaced, check diode and magnetron also.
Oven does not accept
key input (Program)
Timer starts countdown but no
microwave oscillation.
(No heat while oven lamp and
fan motor turn on.)
Samsung Electronics
1. Key input is not in-Sequence
2. Open or loose connection of membrane
key pad to Ass'y PCB
3. Shorted or open membrane panel
4. Defective Ass'y PCB
Refer to operation procedure.
1. Off-alignment of latch switches
2. Open or loose connection of high voltage
circuit especially magnetron filament
circuit
NOTE: Large contact resistance will bring
lower magnetron filament voltage and
cause magnetron to lower output and/or
intermittent oscillation.
3. Defective high voltage components
H.V.Transformer
H.V.Capacitor
H.V.Diode,H.V.Fuse
Magnetron
4. Open or loose wiring of power relay
5. Defective primary latch switch
6. Defective power relay or Ass'y PCB
Adjust door and latch switches.
Replace PCB main.
Check high voltage component according to
component test procedure and replace if it is
defective.
Replace PCB main.
6-1
Troubleshooting
6-1 Electrical Malfunction(continued)
SYMPTOM
CAUSE
CORRECTIONS
Oven lamp and fan motor turn on
1. Misadjustment or loose wiring
of primary latch switch
2. Defective primary latch switch
Adjust door and latch switches.
Oven can program but timer
does not start.
1. Open or loose wiring of secondary
interlock switch
2. Off-alignment of primary interlock
3. Defective secondary interlock S/W
Adjust door and interlock switches.
Microwave output is low;.
Oven takes longer time to
cook food.
1. Decrease in power source voltage.
2. Open or loose wiring of magnetron
filament circuit. (Intermittent oscillation))
3. Aging of magnetron
Consult electrician.
Fan motor turns on when plugged in
Loose wiring of door sensing switch
Check wire of door sensing switch.
Oven does not operate and return
to the plugged in mode.
Defective Ass'y PCB
Replace PCB main.
Loud buzzing noise can be heard.
1. Loose fan and fan motor
2. Loose screws on H.V.Transformer
3. Shorted H.V.Diode
Tighten screws of fan motor.
Tighten screws of H.V.Transformer.
Replace H.V.Diode.
Turntable motor does not rotate.
1. Open or loose wiring of turntable motor.
2. Defective turntable motor.
Check the wire of turntable motor
Replace turntable motor.
Oven stops operation during cooking
1. Open or loose wiring of primary
interlock switch
2. Operation of thermal cutout(Magnetron)
Adjust door and latch switches.
Sparks
1. Metallic ware or cooking dishes
touching on the oven wall.
2. Ceramic ware trimmed with gold or
silver powder also causes sparks.
Inform the customer.
Do not use any type of cookware with
metallic trimming.
Uneven cooking
Uneven intensity of microwave due to
its characteristics.
Wrap thinner parts of the food with
aluminum foil.
Use plastic wrap or cover with a lid.
Stir once or twice while cooking
foods such as soup, cocoa, or milk.
Noise from the turntable motor
when it starts to operate.
Noise may result from the motor.
Replace turntable motor.
6-2
Samsung Electronics
7. Exploded Views and Parts List
7-1 Exploded Views
2
3
1
58
59
4
57
13 14
5
7
56
8 9
55
51
15
1011
16
22
17
12
18
23
54
19
20
69
53
28
27
24
30
29
52
62
31
21
26
51
50
25
35
NC
70
61
33
NO
COM
36
35
34
37
46
60
45
32
38
44
47
63
39
48
40
64
49
42
65
41
43
67
68
66
Samsung Electronics
7-1
Exploded Views and Parts List
7-2 Main Parts List
Ref. No.
1
2
3
4
5
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
Parts No.
DE70-30029B
DE63-90035G
DE61-50073D
DE61-70060A
DE61-30185A
DE47-70031B
DE60-40009B
DE63-20017A
DE60-90006A
DE61-50177A
DE61-50115A
DE61-50076A
DE65-20014A
DE39-20058B
DE71-60058C
DE91-40042A
DE61-30129A
DE31-10080A
DE39-40285A
4713-000168
DE65-20031A
DE63-90065E
DE01-00051A
DE66-90013A
DE62-90046A
DE71-60294A
DE61-30132A
DE47-40029A
DE47-20031A
DE03-30035A
DE92-90213A
DE93-20019B
72681-0004-001
3405-000178
3405-000175
71533-0011-00
71533-0012-00
DE59-40001A
DE91-70061A
: Option Parts
7-2
Description/Specification
Q'ty
PANEL-OUTER;SECC T0.6 W405.5 L1180.8
CUSHION-RUBBER;DFA20 T2 W190 L100 BLK
BRACKET-UPPER;ALSTAR T0.6 W273 L432 MB6544W
SPRING-PLATE;SK-5 T0.5
SUPPORTER-HEATER;ALUMINA T12 NTR
HEATER-GRILL;D6.8 230V 1400W 37.0OHM RE-1300
WASHER-TEFLON; SLOT ID22.2 OD28 T1.2 TEFLON
GASKET-HEATER;BRASS T1.5 OD30.5 ID22.5
FLANGE-RING;C3604BD ID22.1 OD26 L4.7 MBGF45
BRACKET-EARTH;BSS2-A T1.0 W28 L38 M9GF45
BRACKET-HEATER;BSS2-A T1.0 W55 L55.5 M9GF45
BRACKET-AIR GUIDE;ALCOAT T0.8 W61 L218.5
CABLE-CLAMP;DA6-N NY 66
ASSY POWER CORD;KKP-4819D/B232 1.5MM 250V16
COVER-BACK;SCP2(CR) T0.6 W385.5 L275 BLK-CO
ASSY NOISE FILTER;DNA-1019(C)250V 10A CMOSUPPORT-P.C.B;DASS-T9N
MOTOR-FAN;AMM92-002AUEE 230V0.20A MIN2550RPM
WIRE HARNESS-A;230V50HZ RE-1300
LAMP-INCANDESCENT;230V,-,25W,ORG,-,-,
BUSHING;DASB-16N 17.8X6.3 NYLON NTR SHORT BUSHING
CUSHION-LAMP;PUT-FOAM T40 W10 L90 M6245
FILM-LAMP;T0.25 W105 L85 CLEAR RE-1300
LEVER-DOOR;POM(F20-01) NTR MW5630T
ADIABATIC-RIGHT;T3 W219.3 L214.8 RE-1300
COVER-ADIABATIC;SECC T0.6 W249.7 L353.5 RE-1300
SUPPORTER-MGT;SECC T0.6 W38 L342.5 MW6630T
SOCKET-LAMP;250V2A 22.230 E14 BJB
THERMOSTAT;PW-2N 140/30
MAGNETRON;OM75PH(31)ESS
ASSY COVER-AIR; RE-1300
ASSY BODY LATCH;M8145G NEW LATCH
LATCH-BODY;POM 50G M8135G NEW LATCH
SW-MICRO;VP-533A-OF-PS(T85) 250V,15A,20
SW-MICRO;VP-531-OF (T85) 250V,15A,200GF
LEVER-SWITCH(A);POM 10G NTR MX245
LEVER-SWITCH(B);POM 12G NTR MX245
DIODE-H.V;HVR-1X-32B-12
ASSY-H.V.FUSE;THV060T-0800-H 5KV/0.8A RED
: Warning
Remarks
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
:Electrostatically Sensitive Devices
Samsung Electronics
Exploded Views and Parts List
7-2 Main Parts List
Ref. No.
Parts No.
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
DE26-20084A
DE61-40026A
DE60-60025A
DE61-50106A
2501-001030
DE26-10042B
DE63-90065J
DE80-10031B
DE65-20025A
DE31-10097A
DE47-20050A
DE71-60313A
DE61-80036A
DE61-80037G
DE32-10013A
DE72-60035Q
DE39-40339A
DE39-40409A
DE39-30074B
DE63-90062A
DE74-20025C
DE74-20016A
DE92-90189C
DE67-60028A
DE92-90019P
DE92-90019R
DE65-20012A
Samsung Electronics
Description/Specification
TRANS-L.V;RE-1280STC RE-1 230V 50HZ AC16/3V
FOOT;P.P JI350 BLK
PIN-FOOT;P.P-JI350BLK
BRACKET-H.V.C;SECC T0.8 W31 L125.8
C-OIL;1.1uF,2100V,BK,35x54x95,200mm
TRANS-H.V;Y9245NTC-1 230V 50HZ AC2230V
CUSHION-GUIDE;PUT FOAM T40 W10 L460 MX246
BASE-PLATE;SGCC1-Z T0.8 W375 L588 RE-1300
CABLE-CLAMP;DAWS-2NB NYLON66 NTR WIRE SADDL
MOTOR-SYNCHRONOUS;M2LJ24ZS52 220/240V50/60HZ M6235
THERMOSTAT;PW-2N 130/60
COVER-CEILING;MICA SHEET T0.5 W48.5 L117 RE-1300
HINGE-LOWER;SCP1 T3.0 W24.7 L91.2 BLK-COAT
HINGE-UPPER;SCP1 T3.0 W26 L76 BLK-COAT MB24
SENSOR-THERMISTOR;PT-312-K2
GUIDE-AIR;SECC (T)0.6 (W)240 (L)242 5 RE-13
WIRE HARNESS-C;230V50HZ RE-1300
WIRE HARNESS-E;230V50HZ M9G45 CTW
WIRE LEAD-C;L170
ASSY CONTROL-BOX
ASSY DOOR
CUSHON-RUBBER DOOR;RUBBER(CR) T9 W30 L50
TRAY-CONVECTION;SPP T0.8 W12 L325.9 CE104CF
TRAY-COOKING;GLASS T5.0 PI345 1250G M551T
ASSY-GUIDE ROLLER;D22.5 RE-1300
COUPLER;PTFE 20G WHT RE-1300
ASSY-WIRE RACK;CE1279KSE HIGH
ASSY-WIRE RACK);CE1279KSE LOW
CORD-CLAMP;DALC-2-1 SILICI
Q'ty
Remarks
1
4
4
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
7-3
Exploded Views and Parts List
7-3 Exploded View & Parts List - Door Parts
4
5
7
3
6
8
2
1
Ref. No.
Parts No.
1
DE64-40064B
DOOR-A;PC RP-WH-01-K 290G RE-1300
1
2
DE67-20117K
SCREEN-DOOR(B);TEMP GLASS T3.2 W278 L423.7
1
3
DE92-50080E
ASSY DOOR-E;MBG45 COATING SIL/SELANT
1
4
DE64-40173A
DOOR-C;PBT BLK 24G RE-1300
1
5
DE64-40087H
DOOR-KEY;POM(TC3005) BLK 13G W3
1
6
DE61-70030A
SPRING-KEY;ES HSW3 PI0.7 D7.0L40 BULING
1
7
DE60-60008A
PIN-HINGE;PI4 L17 MSWR10 M301TBC
2
8
DE02-00082A
TAPE-DOUBLE FACE;PET T0.4 W9 WHT SEIL SI-500HI
1
9
DE92-40094P
ASSY DOOR;CE101KR(SBTW) WHT
1
7-4
Description/Specification
9
Q'ty
Remarks
Samsung Electronics
Exploded Views and Parts List
7-4 Exploded View & Parts List - Control Parts
8
4
3
1
2
7
6
5
9
Ref. No.
Parts No.
1
DE34-10230C
SWITCH-MEMBRANE;PET 230V 50HZ W90.5xL225.5
1
2
DE67-40094A
WINDOW-DISPLAY;ACRYL(HI-855M) RC-SM-04-K 13G
1
¡
3
DE72-70076B
CONTROL-PANEL;PC RP-WH-01-K 180G RE-1300
1
¡
4
DE91-10057A
ASSY P.C.B;230V50HZ S VFD 1300(RUS
1
¡
5
DE66-20053B
BUTTON-PUSH;PC RP-WH-01-K 32G RE-1300
1
¡
6
DE61-70026A
SPRING-BUTTON;CS SWP PI0.7 D17L25.8
1
7
DE39-30063A
ASSY WIRE LEAD-G;L80 PCB GROUND
1
8
DE93-30482A
ASSY CONTROL-PANEL;CE101K(SAW) WHT
1
9
DE93-30424K
ASSY CONTROL-BOX;230V50HZ CE101KR/BWT WHT
1
Samsung Electronics
Description/Specification
Q'ty
Remarks
¡
7-5
Exploded Views and Parts List
7-5 Exploded View & Parts List - Casing Parts
8
5
6
7
4
2
9
3
1
10
Ref. No.
Parts No.
1
2
3
4
5
6
7
8
9
10
DE60-30016B
DE31-30011A
DE72-30016A
DE62-90045A
DE61-50324A
DE31-90019A
DE60-40026A
DE31-10081A
DE65-20012A
DE92-90078A
7-6
Description/Specification
NUT-FLANGE;M4 MSWR10 FEFN
FAN-CONVECTION;ALSTAR T0.6 PI109 RE-1300
BUSH- MOTOR;MSWR3 D5.6 L12.3 RE-1300
ADIABATIC-CASING;T5 W256 L250 RE-1300
BRACKET-CASING;ALSTAR T0.6 W265 L265 RE-1300
BLADE-FAN;SECC T0.6
WASHER-PLAIN;ID5.5 OD12 T1.0 SBC1
MOTOR-CONVECTION;AMM90-003AUEA 230V0.3A MIN2800RPM
CLAMP-CORD;DALC-2-1SILICIN
ASSY-CASING;RE-1300 230V EUROPE
Q'ty
1
1
1
1
1
1
1
1
1
1
Remarks
¡
¡
¡
¡
¡
¡
Samsung Electronics
Exploded Views and Parts List
7-6 Parts List - Standard Parts
Parts No.
DE60-10098A
DE60-10098A
DE60-10082H
DE60-10082H
DE60-20014A
DE60-10046A
DE60-10052A
DE60-10080A
DE60-10082H
DE60-10012A
DE60-10013A
DE60-10018A
DE60-10012A
DE60-10082H
DE60-10082H
DE60-10088A
DE60-10034A
DE60-10082H
DE60-10082H
DE60-10122A
DE60-10122A
DE60-10080A
DE60-10082H
DE60-10082H
DE60-10082H
DE60-10082H
DE60-10082H
DE60-10082H
DE60-10082H
DE60-10082H
DE60-10098A
DE60-10082H
DE60-30016B
DE60-10013A
DE60-10082H
Description/Specification
SCREW-ASSY TAPTITE;PH TC M4X8 SWRCH18A Z
SCREW-ASSY TAPTITE;PH TC M4X8 SWRCH18A Z
SCREW-A;2S-4X12(TOOTHED)
SCREW-A;2S-4X12(TOOTHED)
BOLT-FLANGE;M5 L10 MSWR3 FEFZY
SCREW-TAP PH;PH M3 L8 FEFZY
SCREW-TAP PH;PH M4 L8 FEFZY
SCREW-WASHER;M5 L12 2S
SCREW-A;2S-4X12(TOOTHED)
SCREW-TAP TITE;TH + 3 M4 L10 SWR10 ZPC2
SCREW-ASSY TAP;TH 2S 4 L12 MSWR3 ZPC3 FI
SCREW-ASSY MACHINE;PH M4X0.7P 8 MSWR10 S
SCREW-TAP TITE;TH + 3 M4 L10 SWR10 ZPC2
SCREW-A;2S-4X12(TOOTHED)
SCREW-A;2S-4X12(TOOTHED)
SCREW-TAP PH;PH M3 L8 FEFZY PLAIN
SCREW-TH;TH + M4 L10 STS304
SCREW-A;2S-4X12(TOOTHED)
SCREW-A;2S-4X12(TOOTHED)
SCREW-TAP TH;TAP TH 2-4X8 FE FN
SCREW-TAP TH;TAP TH 2-4X8 FE FN
SCREW-WASHER;M5 L12 2S
SCREW-A;2S-4X12(TOOTHED)
SCREW-A;2S-4X12(TOOTHED)
SCREW-A;2S-4X12(TOOTHED)
SCREW-A;2S-4X12(TOOTHED)
SCREW-A;2S-4X12(TOOTHED)
SCREW-A;2S-4X12(TOOTHED)
SCREW-A;2S-4X12(TOOTHED)
SCREW-A;2S-4X12(TOOTHED)
SCREW-ASSY TAPTITE;PH TC M4X8 SWRCH18A Z
SCREW-A;2S-4X12(TOOTHED)
NUT-FLANGE;M4 MSWR10 FEFN
SCREW-ASSY TAP;TH 2S 4 L12 MSWR3 ZPC3 FI
SCREW-A;2S-4X12(TOOTHED)
Samsung Electronics
Q'ty
2
2
1
2
4
2
1
4
9
3
4
2
1
1
2
5
1
2
1
2
2
4
2
1
1
2
5
4
2
1
4
1
1
1
2
Remarks
CV-TCO
M/DRIV
CV/AIR
SW-THE
HINGE
MGTCO
B/HING
HVT
BASEGROUP
CV-MOT
B/EART
HVD
B/C-MO
LVT
PCB
SENSOR
CV-BAK
BKT/U
B/HEAT
C-CEIL
MGT
CN-BOX
CV/AIR
SU/MGT
SW-THE
PN-OUT
A/CSIG
B/LATH
B/WAVE
AS-CSI
B/AI-G
SENSOR
CB-CMP
GU-AIR
7-7
8. P.C.B Diagrams
8-1 P.C.B Diagrams
8-1
Samsung Electronics
P.C.B Diagrams
8-2 P.C.B Parts List
Parts No.
0401-001002
0402-000559
0403-000387
0501-000283
0501-000388
0504-001014
0504-001015
2001-000037
2001-000273
2001-000290
2001-000429
2001-000435
2001-000613
2001-000780
2011-001072
2202-000780
2202-000796
2401-000247
2401-000914
2401-001412
2802-000143
3501-001014
3501-001015
3501-001016
3501-001016
3708-000528
3711-000203
3711-000240
3711-000881
71607-402-290
A1100-1049
A4106-0154
DE07-10081A
DE09-30509A
DE13-20009A
DE26-20141A
DE30-20016A
DE39-60001A
DE41-10361A
DE60-60012A
DE61-90004A
Samsung Electronics
Description / Specification
DIODE-SWITCHING;1N4148M,100V,200mA,500mW
DIODE-RECTIFIER;D4G,400V,1A,T-1
DIODE-ZENER;UZP24B,24V,22.8-25.6V,1W,DOTR-SMALL SIGNAL;KSA539-Y,PNP,400mW,TO-92
TR-SMALL SIGNAL;KSC815-Y,NPN,400mW,TO-92
TR-DIGITAL;KSR1005,NPN,300mW,4.7K-10K,TO
TR-DIGITAL;KSR2005,PNP,300mW,4.7K-10K,TO
R-CARBON(S);330ohm,5%,1/2W,AA,TP,2.4x6.4
R-CARBON;100Kohm,5%,1/8W,AA,TP,1.8x3.2m
R-CARBON;10Kohm,5%,1/8W,AA,TP,1.8x3.2mm
R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm
R-CARBON;1Mohm,5%,1/8W,AA,TP,1.8x3.2mm
R-CARBON;3.9Kohm,5%,1/8W,AA,TP,1.8x3.2m
R-CARBON;470ohm,5%,1/8W,AA,TP,1.8x3.2mm
R-NETWORK;47Kohm,5%,1/8W,A,SIP,6P,TP
C-CERAMIC,MLC-AXIAL;UP050F104Z 100NF,+80
C-CERAMIC,MLC-AXIAL;UP050B102KB 1NF,10%,
C-AL;1SA1ANB107MAN 100UF,20%,10V,GP 6.3X
C-AL;CESSL1C220M0511AA 22UF,20%,16V,GP 5
C-AL;1SG1VFB477MAN 470UF,20%,35V,GP 10X1
RESONATOR-CERAMIC;KBR-4.19M 4.19MHZ,0.5%
RELAY-POWER;OM1F-S-124LM 24V,21.8MA,17A
RELAY-POWER;OZF-S-124LM1P 24V,21.8MA,16A
RELAY-MINIATURE;JV24-KT 24V,12.5MA,5A 1F
RELAY-MINIATURE;JV24-KT 24V,12.5MA,5A 1F
CONNECTOR-FPC/FC/PIC;FCZ254-13SL,BLK 13P
CONNECTOR-HEADER;YW396-03AV WHT STRAIGHT
CONNECTOR-HEADER;1WALL,4P,1R,3.96mm,STRA
CONNECTOR-HEADER;SMW250-03,WHT BOX,3P,1R
C-ELEC;04W 50V 100UF (TAPG)
C-CERAMIC;CC OA CH 50V T 220-J 3.5X1.9 U
DIODE-ZENER;TZP5.1B 5.1/5.7V 40MA T 1W
V.F.DISPLAY;SVM-4SM03 GRN/RSHORG 4 51 81
IC-MCU;HD404316-C16S DIP CE945G/CE745G(E
IC;KA7533 DIP
TRANS-L.V;SLV-945E 230V 50HZ AC17/2.9V
BUZZER;CBE2220BA STICK
WIRE-SO COPPER;PI0.6 SN T 52MM TAPING_WI
P.C.B-MAIN;FR-1 T1.6 W88 L163 EU2(M945)
PIN-EYELET;ID2.1 OD2.5 L3.0 SN BSP T0.25
HOLDER-DIGITRON;NYLON#66 1.5 85 36 8GR B
Q'ty
Remarks
16
3
1
1
1
6
1
2
1
6
8
1
7
2
1
5
4
1
1
1
1
1
1
1
1
1
1
1
1
1
2
3
1
1
1
1
1
25
1
8
1
D4~19
D1~3
ZD04
TR01
TR03
TR2,4~8
TR09
R1,2
R16
R12~14,19~21
R5,6,8~10,18,22,23
R07
R11,15,17,24~27
R3,4
AR01
C5,6,9,10,19
C11~14
C03
C04
C01
XTL1
RY01
RY04
RY02
RY03
CN04
CN01
CN02
CN03
C02
C7,8
ZD1~3
VFD1
IC01
IC02
LVT1
BUZ1
J1~25
E1~8
8-2
9. Schematic Diagrams
9-1 Schematic Diagrams
S/W1
S/W2
V/G
E
H
F
WHT
BLU
RY1
2200pF
ORG
ORG
ROT
RY4
BRN
H.V.T
YEL
RY5
CM
FM
E
S/W5
F2
(0.8A)
YEL
BLK
YEL
WHT
R
BLU
YEL
WHT
F3
(1.6A)
YEL
BLU
H.V.D
H.V.C
DM
ORG
BLU
0V
ORG
WHT
L
N
BLU
BRN
WHT
WHT
1mH
500K
WHT
2200pF
230V~
50Hz
S/W3
BRN
BRN
F1
S/W6
BRN
LIN-CAPACITORT 0.1uF
L
BRN
FUSE 10A
BRN
L.V.T
Ass'y chike P.C.B
RY2
RY6
ORG
F
BLU
BLU
FA
RY3
MAGNETRON
RY2
RY3
RY4
RY5
RY6
ORG
KEY BOARD
OFFENZUSTAND
GRN
ORG
RY1
S/W4
DOOR IS OPENED
COOK OFF
A S S Y M A I N P.C.B
WIRING COLOR
BRN :BROWN BLU : BLUE
WHT : WHITE ORG : ORANGE
RED : RED
YEL : YELLOW
Y/G : YELLOW/GREEN
COM NO
BRN
COM NO
BRN WHT
PRIMARY LATCH
SWITCH
ORG
ORG
DOOR SENSING
SWITCH
NO
COM NO
BRN YEL
RED BLU
BRN
MONITOR
SWITCH
F1
F2
F3
S/W1
S/W2
S/W3
S/W4
S/W5
S/W6
RY1
RY2
RY3
RY4
RY5
RY6
MAIN FUSE
H.V.FUSE
MONITOR FUSE
THERMAL CUTOUT(CAVITY)
THERMAL CUTOUT(M.G.T)
PRIMARY SWITCH
DOOR SENSING SWITCH
MONITOR SWITCH
THERMAL CUTOUT(HEATER)
HEATER RELAY
MAIN RELAY
POWER RELAY
CONVECTION MOTOR RELAY
FAN MOTOR RELAY
INRUSH RELAY
FM
DM
CM
H
H.V.T
H.V.C
H.V.D
L.V.T
L
R
FAN MOTOR
DRIVE MOTOR
CONVECTION MOTOR
HEATER
HIGH VOLTAGE TRANS
HIGH VOLTAGE CAAPCITOR
HIGH VOLTAGE DIODE
LOW VOLTAGE TRANS
LAMP
RESISTOR
MAGNETRON
HIGH VOLTAGE
DIODE
TO CHASSIS
FA
F
HIGH VOLTAGE CAPACITOR
ORG
RED
RED
H.V.FUSE
BRN
RED
BLU
SYMBOL COLOR
ORG
ORANGE
BRN
BROWN
BLK
BLACK
RED
RED
BLU
BLUE
HIGH VOLTAGE
TRANSFORMER
9-1
Samsung Electronics