Black BLK-CPV700RH User manual

BLK-CPV700RH High Performance 700TVL
Extended Temperature Range Vandal-proof
CCTV Dome Camera User Manual
Products: BLK-CPV700RH
BLK-CPV700RH camera
Please read this manual before using your camera, and always follow the instructions for
safety and proper use. Save this manual for future reference.
BLK-CPV700RH_CM
12/9/13
!
WARNING

CAUTION
Changes or modifications not expressly approved by the manufacturer could void the
user’s authority to operate the equipment.
To prevent electric shock and risk of fire hazards, do NOT use other than the specified power source.
REGULATORY NOTICE
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and use in
accordance with the instructions, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause interference, in which case the user will be
required to correct the interference at his own expense.
LEGAL NOTICE
Observint Technologies (Observint) products are designed to meet safety and performance standards with the use of
specific Observint authorized accessories. Observint disclaims liability associated with the use of non-Observint
authorized accessories.
The recording, transmission, or broadcast of any person’s voice without their consent or a court order is strictly
prohibited by law.
Observint makes no representations concerning the legality of certain product applications such as the making,
transmission, or recording of video and/or audio signals of others without their knowledge and/or consent. We
encourage you to check and comply with all applicable local, state, and federal laws and regulations before
engaging in any form of surveillance or any transmission of radio frequencies.
Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks
and names or their products. Observint disclaims any proprietary interest in trademarks and trade names other than
its own.
No part of this document may be reproduced or distributed in any form or by any means without the express written
permission of Observint.
© 2013 Copyright Observint Technologies. All Rights Reserved.
11000 N. Mopac Expressway, Building 300, Austin, TX 78759
For Sales and Support, please contact your distributor.
ii
Table of Contents
SECTION 1
SECTION 2
SECTION 3
SECTION 4
SECTION 5
APPENDIX A
APPENDIX B
APPENDIX C
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.1Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.1.1 What’s in the box. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
1.1.2 Tools you need. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2.1 General Guidelines. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2.2 Mounting the camera. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
2.2.1 Camera field of view adjustments. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
OSD Software Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3.1 OSD menu tree . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3.2 OSD Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Cleaning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Glossary. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
B.1 IR level adjustment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Camera Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
High Performance 700TVL CCTV Dome Camera User Manual
iii
Precautions
•
•
•
•
•
•
This camera should be installed by qualified personnel only.
There are no user serviceable parts inside.
Do not disassemble this camera other than to make initial adjustments.
Use a UL approved regulated 24 volt AC or 12 volt DC power supply.
Use appropriate low voltage power cable to prevent fire or electrical shock.
Please insure that your installation area can support the weight of the camera.
Handle this camera carefully
•
•
•
•
•
•
•
•
•
•
•
•
•
iv
Do not use a strong or abrasive detergent when cleaning the camera.
Do not install near cooling or heating devices.
Do not install the camera in extreme temperature conditions. Use the camera in environments where temperature
is within -40 °F to 122 °F. Use adequate ventilation if a camera is installed where high temperatures may occur.
Do not install or use the camera in an environment where the humidity is high. Very high humidity levels can
reduce image quality.
Do not install the camera under unstable lighting conditions. Severe lighting change or flicker can cause the camera
to work improperly.
Do not touch the front lens of the camera. Be careful not to leave fingerprints on the lens or camera dome.
Do not drop the camera or subject it to physical shocks.
Do not expose the camera to rain or spill liquids on it. If it gets wet, wipe dry immediately. Liquids can contain
minerals that corrode the electronic components.
Do not expose the camera to radioactivity. If exposed to radioactivity the CCD will fail.
Do not disassemble the camera. There are no user-serviceable parts inside it.
Do not drop the camera or subject them to physical shocks. It can cause malfunctions to occur.
Never point the camera at a strong light, or exposing it to a spotlight or an object reflecting the strong light.
Smear or blooming may occur, and it can damage the image sensor.
Before applying power to the camera, check the power source to ensure that it is within specifications.
SECTION 1: INTRODUCTION
SECTION 1
Introduction
This high performance extended temperature CCTV dome camera feature a very high resolution CCD sensor providing 700 TVL,
dual voltage range (24 Vac, 12 Vdc), and on-screen display (OSD) for control and setup. The BLK-CPV700RH camera features a
vandal‑proof case and is weather-proof with a cold temperature range to -40 °F.
1.1 Features
•
•
•
•
•
•
•
•
•
•
•
•
•
•
1/3” 960H Interline CCD sensor
700 TVL horizontal resolution
Vandal-proof and weather-proof (IP66 rated)
Varifocal (2.8 ~12.0 mm)
True Day & Night (ICR) with built-in 30 IR LEDs
Fast shutter speed (1/60 ~ 1/100,000 sec)
2D Digital Noise Reduction (2D DNR)
Adaptive Tone-curve Reproduction (ATR): provides gradation compensation to improve the contrast of subjects both lowluminance areas and high luminance areas exist in the same picture.
Back Light Compensation (BLC) and Highlight Compensation (HLC)
4-Zone Privacy Masking and Motion Detection
Mirror / Brightness / Contrast / Sharpness / HUE / Gain image adjustments
12 Vdc / 24 Vac dual power
Multilingual OSD
Second video output for easy servicing
IR LED
Cooling fan
IR LED volume
OSD joystick
Video test port
High Performance 700TVL CCTV Dome Camera User Manual
1
SECTION 1: INTRODUCTION
Zoom
adjustment
Focus
adjustment
BLK-CPV700RH zoom - focus adjustment knobs
1.1.1 What’s in the box
Your camera includes the following:
•
•
•
•
•
•
Camera assembly
Four (3) coarse-threaded screws and wall inserts to secure the base to the mounting surface
Torx® (T-20) L-wrench for removing the dome
Surface mounting template
Video test port to BNC adapter cable
This manual
1.1.2 Tools you need
To install the camera, you will need:
•
•
•
•
•
2
12 Vdc or 24 Vac power source
Tools for mounting the camera
Plillips #2 screwdriver
Video and power extension cables, if needed
Hand-held CCTV video setup monitor (optional)
SECTION 1: INTRODUCTION
SECTION 2
Installation
2.1 General Guidelines
The camera can be mounted on a flat surface (surface mounted, usually on a ceiling). The camera drop cable can be routed through
a hole in the ceiling, or through a cable channel on the side of the camera base.
Following are some general guidelines for installing the camera.
•
•
•
•
Camera Lens: Handle the camera dome carefully to prevent scratching or soiling the dome and lens. If the dome or lens
becomes soiled, clean it only with approved products. See the Cleaning section later in this manual.
Monitor impedance: Set the monitor impedance switch to 75Ω.
Power supply: To avoid fire or shock hazard, use only a UL listed power supply.
Camera drop cable: The camera drop cable includes two connectors:
—— Power connector (red sleeve) – Use 24 Vac power source (AC24V 1A adapter) or 12 Vdc power source (DC12V 1A
adapter). When connecting 12 Vdc power to the camera power drop. When connecting 12 Vdc power to the drop cable
connector, observe the polarity - the center tap must be positive compared to the outer shield.
—— Video coax connector (BNC, yellow sleeve) – for transmission of the video signal across coax (75 Ω) cable.
Drop cable
Drop cable
channel
Video BNC
connector
Power
connector
Video (yellow) and power (red) drop cable connectors
2.2 Mounting the camera
The camera can be mounted onto an electrical box, mounting bracket, or flat surface with sufficient strength to support it.
High Performance 700TVL CCTV Dome Camera User Manual
3
SECTION 2: INSTALLATION
When the camera is surface mounted, the drop cable can be routed through a hole within the perimeter of the base, or through the
cable channel on the side.
1.
Determine (and acquire, if needed) the best type of fasteners for attaching the camera to the mounting surface. The
mounting screws and wall inserts provided are adequate for most surfaces.
2.
Use the template provided to mark the location for the fasteners for mounting the camera. Also, if the camera drop cable will
pass through the mounting surface, mark the location for the hole.
3.
Drill holes in the mounting surface appropriate for the fasteners. Drill a 3/4" hole for the camera drop cable, if needed.
4.
If needed, insert wall inserts in the screw holes.
5.
Remove the camera dome cover from the camera. Loosen
the three dome captive screws using the Torx L-wrench
provided.
6.
Route the drop cable through the cable channel on
the side of the base, or through the hole drilled in the
mounting surface.
7.
Secure the camera to the mounting surface with three
screws.
8.
CAUTION
NOTE
4
Wall inserts
(if needed)
Screws (3)
Connect the camera drop cable video and power leads to a video and power extension cable as needed. If using 12 Vdc to
power your camera, ensure that +12 Vdc is applied to the center pole of the power drop cable connector.

9.
Template
When using 12 Vdc powering, use extreme caution to observe the polarity of the of the voltage applied to the camera.
The camera power drop cable connector center lead should receive +12 Vdc when measured to the shield (ground).
Drop cable connectors are not waterproof.
Attach the far end of the video extension cable to video monitoring equipment such as a monitor or DVR.
SECTION 2: INSTALLATION
Video female
BNC connector
Extension cables
To a 12 Vdc or 124 Vac
regulated power supply
10. Attach the far end of the power extension cable to a 12 Vdc or 24 Vac power source.
11. Apply power to the camera. Verify that video from the camera can be seen on the video monitor.
2.2.1 Camera field of view adjustments
In this procedure, point the camera at your surveillance (field of view) target and adjust zoom and focus.
1.
Monitor video from your camera. You can monitor video using your DVR/monitor, or by watching video with a setup monitor
attached to the video test port. NOTE: A video test port to BNC adapter cable is provided.
IR LED gain
adjustment
Video test port
OSD Joystick
OSD Joystick
2.
Adjust the pan and tilt camera gimbal to center the surveillance target in your camera video. Note that the tilt will adjust 70°.
See the drawing below. Tighten the tilt set screw to hold the tilt adjustment in place.
High Performance 700TVL CCTV Dome Camera User Manual
5
SECTION 2: INSTALLATION
Tilt set screw
Pan adjustment
3.
Tilt adjustment
Tilt angle
Adjust the camera Rotation to align the horizon in the video image.
Camera rotation
4.
Adjust the camera zoom and focus to frame and clarify the image. Turn each adjustment knobs counterclockwise to loosen,
push right or left to produce the best image, then turn the knob clockwise to tighten.
Zoom
adjustment
Focus
adjustment
5.
Perform the OSD software setup of your camera to produce the best video image in all environmental conditions. See Section
3, OSD Software Setup, for more information.
6.
Reinstall the dome cover.
6
SECTION 3: OSD SOFTWARE SETUP
SECTION 3
OSD Software Setup
The OSD (On Screen Display) software setup menus can be viewed from the camera video output or through the VIDEO TEST port
on the OSD Control board. The OSD control board is accessible when the camera dome is remove. Configuration settings are made
using the OSD joystick (see photo below).
IR LED gain
adjustment
Video test port
OSD Joystick
OSD Joystick
Use the SETUP joy stick on the OSD control panel to navigate
through the menu system. Press the joy stick in (toward the
control board) to open the SETUP menu or select an entry, rock
the stick up or down to highlight an item in the list, and left or
right to change the option (right column) of the highlighted item.
When an option contains a 8 symbol, selecting that option
opens a sub-menu.
The MAIN menu consists of a list of sub-menus or displays the
option selected for a camera function. When sub-menus are
available, the  symbol is shown.
3.1 OSD menu tree
Table 1.OSD menu
MAIN MENU
1st Sub MENU
2nd Sub MENU
3rd Sub MENU
TYPE
DC
MODE
AU TO, O P E N , C LO S E
SPEED
(0 0 0 ~ 2 55 )
4th Sub MENU
M A N UA L
LENS
AU TO
RETURN
High Performance 700TVL CCTV Dome Camera User Manual
7
SECTION 3: OSD SOFTWARE SETUP
MAIN MENU
1st Sub MENU
2nd Sub MENU
HIGH LUMINANCE
AU TO
LO W L U M I N A N C E
3rd Sub MENU
4th Sub MENU
MODE
AUTO IRIS,
SHUT+AUTO IRIS
BRIGHTNESS
(0 0 0 ~ 2 55 )
MODE
AG C , O F F
BRIGHTNESS
x0.25, x0.50, x0.75, x1.00
RETURN
SHUTTER / AGC
MODE
S H U T+AG C
SHUTTER
1/100, 1/60, 1/250, 1/500,
1/1000, 1/2000, 1/4000,
1/10000
AG C
6, 12, 18, 24, 30, 36,
42, 44.8
M A N UA L
RETURN
AT W
SPEED
(0 0 0 ~ 2 55 )
D E L AY C N T
(0 0 0 ~ 2 55 )
AT W F R A M E
x0.50, x1.00, x1.50, x2.00
ENVIRONMENT
INDOOR,OUTDOOR
RETURN
PUSH
WHITE BAL
USER1
B-GAIN
(000 ~ 255)
R-GAIN
(0 0 0 ~ 2 55 )
RETURN
USER2
B-GAIN
(0 0 0 ~ 2 55 )
R-GAIN
(0 0 0 ~ 2 55 )
RETURN
ANTI CR
M A N UA L
PUSH LOCK
BACK LIGHT
8
OFF, BLC, HLC
LEVEL
RETURN
24 ~ 10 3
SECTION 3: OSD SOFTWARE SETUP
MAIN MENU
PIC
ADJUST
1st Sub MENU
2nd Sub MENU
MIRROR
O F F, O N
BRIGHTNESS
(0 0 0 ~ 2 55 )
CO N T R A S T
(0 0 0 ~ 2 55 )
SHARPNESS
(0 0 0 ~ 2 55 )
HUE
(0 0 0 ~ 2 55 )
GAIN
(0 0 0 ~ 2 55 )
3rd Sub MENU
4th Sub MENU
RETURN
AT R
ON
LUMINANCE
LOW,MID,HIGH
CO N T R A S T
LOW, MIDLOW, MID,
MIDHIGH, HIGH
RETURN
OFF
DETECT SENSE
(0 0 0 ~ 12 7 )
B LO C K D I S P
OFF, ON, ENABLE
(CONTROLLER)
M O N I TO R A R E A
ON,OFF
1/4, 2 /4, 3/4, 4 /4
M OT I O N D E T
ON
AREA SEL
TO P
(000 ~ 244)
BOTTOM
(000 ~ 244)
LEFT
(000 ~ 474)
RIGHT
(000 ~ 474)
RETURN
OFF
NEXT
EXIT
SAVE ALL
High Performance 700TVL CCTV Dome Camera User Manual
9
SECTION 3: OSD SOFTWARE SETUP
MAIN MENU
1st Sub MENU
2nd Sub MENU
3rd Sub MENU
4th Sub MENU
1/4, 2/4, 3/4, 4/4
TOP
AREA SEL
P R I VAC Y
ON
(000 ~ 244)
BOTTOM
LEFT
(000 ~ 474)
RIGHT
(000 ~ 474)
CO LO R
(1 ~ 8)
TRANSP
0 . 0 0 , 0 . 5 0 , 0 .75,
1. 0 0
MOSAIC
O F F, O N
RETURN
OFF
NR
NR MODE
O F F,Y, C ,Y/ C
C LEVEL
(0 0 0 ~ 015 )
Y LEVEL
(0 0 0 ~ 015 )
RETURN
ON
CAMERA ID
EDIT MODE
RETURN
OFF
LANGUAGE
ENGLISH,JAPANESE, DEUTSCH, FRANCAIS, Русский, PORTUGUÊS, ESPAÑOL
CAMERA RESET
BACK
EXIT
SAVE ALL
*Important Note:
•
•
10
Save changes made to the camera settings menus before exiting the OSD menu.
Changing the lens option in the OSD from MANUAL to AUTO will automatically change the SHUTTER / AGC setting from AUTO
IRIS to SHUT+AUTO IRIS. (Default: AUTO IRIS)
SECTION 3: OSD SOFTWARE SETUP
3.2 OSD Description
LENS
The LENS options include two modes: MANUAL and AUTO. In MANUAL mode, the camera uses an automatic electronic shutter.
In AUTO mode, you can set the mechanical lens to fully OPEN, fully CLOSED, or automatically controlled by the camera. SPEED sets
set the convergence speed of the mechanical iris. The lower the value, the faster the speed. If the speed is too slow or too fast, iris
control may be unstable.
SHUTTER / AGC
The SHUTTER / AGC control has two submenus: AUTO and MANUAL. In AUTO mode, the camera controls the shutter and iris based
on the BRIGHTNESS level for both HIGH LUMINANCE and LOW LUMINANCE fields of view.
•
•
In AUTO IRIS mode, the light level is controlled by an auto iris lens only.
In SHUT+AUTO IRIS mode, light level is controlled by the combination of the auto iris lens and shutter control. This mode
generally minimizes washout and produces a better dynamic range. Shutter speed can vary from 1/60 to ~ 1/10,000 sec.
In MANUAL mode, you can preset constant values for the shutter and gain (AGC) levels to constants.
WHITE BAL
WHITE BAL (balance) submenus are used to set the color temperature of the camera to match the color temperature of the field of
view. You can create two preset modes, USER1 and USER2, to use when the scene changes between two common light conditions,
or preset a constant (MANUAL) color temperature correction.
ATW (Auto Tracking White balance) limits the color temperature range at about 2,500 °K ~ 8,500 °K to reduce the excessive
compensation for big objects that have a single color.
Use the PUSH option to allow the camera to automatically set the white balance in all lighting conditions.
ANTI CR (Anti Color Rolling) can reduce color rolling under the fluorescent light when the camera operates in shutter control without
an auto iris lens.
The PUSH LOCK feature provides an alternate way to set the luminance level of the field of view. To use PUSH LOCK, point the
camera at a white paper in the field, then press ENTER. If the environment lighting changes, repeat this procedure to reset the
camera.
Backlight
•
•
BLC - Back light compensation. A function of the camera that compensates for excessive light directed at the camera causing
the video to bloom or causing the images in front of the light to be unusable.
HLC - Headlight compensation. This option blocks very bright light in the image.
High Performance 700TVL CCTV Dome Camera User Manual
11
SECTION 3: OSD SOFTWARE SETUP
PIC ADJUST
Use PIC (picture) ADJUST to improve the live view image from the camera.
ATR
Adaptive Tone-curve Reproduction (ATR) provides gradation compensation to improve the contrast of subjects when both low
luminance areas and high luminance areas exist in the same picture. You can adjust the ATR luminance and contrast levels in the
ATR submenus .
Motion Detection
Motion detection is used trigger recording when motion is detected in the image. You can enable areas (BLOCKS) of the image
where you want to sense for motion, and set the sensitivity (DETECT SENSE) to a level that best triggers when objects of a minimum
size is to be detected.
NR
NR MODE (noise reduction) is used to select to use preset noise reduction values for luma, chroma, or both.
•
•
Y LEVEL: Select to set a specific gamma setting for luma.
C LEVEL: Select to set a specific gamma setting for chroma.
Camera ID
Use to display the camera identifier in the video image.
CAMERA RESET
Select to reset the camera options to the factory default values.
RETURN
Return to the previous higher level menu.
SAVE ALL
Save all current setting and Close OSD menu. These setting are loaded and applied automatically when the Camera is power on.
EXIT
Close OSD menu. Camera’s current setting is not saved.
12
SECTION 4: CLEANING
SECTION 4
Cleaning
Clean the camera dome with an approved glass cleaning solution and a lint free cloth.
•
•
Dust can be removed from the unit by wiping it with a soft damp cloth. To remove stains, gently rub the surface with a soft
cloth moistened with a mild detergent solution, then rinse and dry it with a soft cloth.
Remove all foreign particles, such as plastic or rubber materials, attached to the camera housing. These may cause damage to
the surface over time.

CAUTION
Do not use benzene, thinner or other chemical products on the camera assembly; these may dissolve the paint and
promote damage of the surfaces. Before using any chemical product, read the accompanying instructions carefully.
High Performance 700TVL CCTV Dome Camera User Manual
13
SECTION 5: SPECIFICATIONS
SECTION 5
Specifications
Table 2.Component Specifications
14
Feature
Specification
Image Device
1/3" 960H Interline CCD II
Scanning System
2:1 Interlace
H. Resolution
700 TV Lines
Scanning Frequency
H:15.734 KHz, V:59.94 Hz
Total Pixels
1020 (H) x 508 (V)
Effective Pixels
976 (H) x 494 (V)
Synchronization
Internal
Lens size
Varifocal: 2.8 ~12.0 mm
Electronic Shutter Speed
1/60 – 1/10000 sec
S/N Ratio
More than 50 dB (AGC Off)
Gamma
r = 0.45
Min. Illumination
COLOR : 0.05 lux / B/W : 0.02 lux
Sync System
Internal
Video Output
1.0 Vp-p composite (75 Ω)
OSD
Built in (inner key / joystick)
BLC
OFF / BLC / HLC
White Balance
ATW / PUSH / USER1 / USER2 / ANTI CR / MANUAL / PUSH-LOCK
2DNR
OFF / ON (level adjustable)
ATR
OFF / ON (level adjustable)
Min. Illumination
0 Lux (IR LED on)
IR LED
850 nm, 30 LEDs
IR Beam Range
Up to 98 feet (30 meters)
IR LED Operation
On: 1 lux, Off: 3 lux
Picture Adjust
MIRROR / BRIGHTNESS / CONTRAST / SHARPNESS / HUE / GAIN
Privacy Masking
OFF / ON (4 zones)
Motion Detection
OFF / ON (4 zones)
Language
ENGLISH / JAPANESE / GERMAN / FRENCH / RUSSIAN / PORTUGUESE / SPANISH / CHINESE
IP Rating
IP66 (weatherproof)
SECTION 5: SPECIFICATIONS
Feature
Power Consumption
Specification
12 Vdc (± 10 %) maximum 620 mA
Dual voltage: 12 Vdc (±10 %) maximum 710 mA , 24 Vac (±10 %) maximum 17.3 W
Operating Temperature
-40 °F ~ 122 °F (-40 °C ~ +50 °C) with heater
Storage Temperature
-4 °F ~ 140 °F (-20 °C ~ +60 °C)
Operating Humidity
Relative humidity (RH) < 80 %
Options
Dual power, fan, heater
Dimension (mm)
5.95" (Φ) x 4.86" (V) (151 mm (Φ) x 123.4 mm (V))
Weight
31 oz (880 g)
High Performance 700TVL CCTV Dome Camera User Manual
15
APPENDIX A: GLOSSARY
APPENDIX A
Glossary
Terms and definitions
Term
Definition
AGC
Automatic Gain Control, an electronic circuit that amplifies the video signal when the strength of the signal falls below a given
value.
ALC
Photometric control, measures light intensity. Determines the iris reaction sensitivity. Sensitivity is increased when the potentiometer is turned towards PEAK, and decreased when turned towards AVERAGE.
APERTURE
The opening of the lens which controls the amount of light reaching the surface of the pickup device. The size of the aperture is
controlled by the iris adjustment.
APERTURE SCALE
The aperture scale is referred to as a F-number. The international aperture scale is: F1, F1.4, F2, F2.8, F4, F4.6, F8, F11, F16, etc.
AUTO-IRIS LENS
A lens with a electronically controlled iris. This allows the lens to maintain one light level throughout varying light conditions.
BLC
Back light compensation. A function of the camera that compensates for excessive light directed at the camera causing the video to
bloom or causing the images in front of the light to be unusable.
CAMERA FORMAT
The approximate size of a camera image pickup device. This measurement is derived from the diagonal line of a chip or the diameter
of the tube. Currently there are five format sizes in the CCTV industry 1”, 2/3”, 1/2”, 1/3” and, 1/4”
DC TYPE AUTO-IRIS
Auto-iris lenses where the iris is controlled by the circuitry of the camera.
DEPTH OF FIELD
The regions in front of and behind the focused distance where the image remains in focus. With a greater the depth of field, more of
the scene near to far is in focus. Lens aperture and scene lighting will greatly influence the D.O.F.
F-NUMBER
Indicates the brightness of the image formed by the lens, controlled by the iris. The smaller the F-number the brighter the image.
FIELD OF VIEW
The horizontal or vertical scene size at a given length from the camera to the subject.
FOCAL LENGTH
The distance from the center of the lens to a plane at which point a sharp image of an object viewed at an infinite position. The focal
length determines the size of the image and angle of FOV seen by the camera through the lens. This is the center of the lens to the
image pickup device.
HUNTING
An industry term used to describe a auto-iris lenses inability to stabilize under certain light conditions.
IRIS
A mechanical diaphragm which can be controlled manually or automatically to adjust the lens aperture.
LENS FORMAT
The approximate size of a lens projected image. In most cases the lens will project a image slightly greater than the designated
image size to insure the pickup device is completely covered. It is recommended that camera and lenses are the same format size. A
lens a larger format size can be used on a smaller format camera, however a smaller format lens should never be used with a larger
format camera.
LEVEL CONTROL
Used to set the auto-iris circuit to a video level desired by the user. Turning the level potentiometer towards the HIGH position will
open the iris allowing more light to pass through the lens, towards the LOW will close the iris allowing less light to pass through
the lens.
MANUAL IRIS LENS
A lens with a manual adjustment to set the iris opening (aperture) to a fixed position. This type lens is generally used in fixed
lighting conditions.
TELEPHOTO
Telephoto is a term used to describe lenses that have a high focal number causing the reproduced image to appear larger than
human eye reproduction.
VARIFOCAL
A low cost version of a zoom lens designed to meet installers needs for versatility. This lens does not have the ability to track from
wide to telephoto.
16
APPENDIX B: TROUBLESHOOTING
APPENDIX B
Troubleshooting
Problem
Possible Cause
Nothing appears on the screen
- Check the power connection.
- Check the video signal cable connection to the monitor.
The video image is dim or not clear.
- If the camera lens is dirty, clean it with a soft, clean cloth.
- Adjust the monitor controls, if necessary.
- If the camera is facing a very strong light, change the camera position.
- Adjust the lens focus.
The screen is dark.
- Adjust the contrast control of the monitor.
- If you have an intermediate device, set the impedance (75Ω /Hi-Z) properly, and check the cable
connections.
The camera is not working properly and
the surface of the camera is hot.
- Verify that the camera is correctly connected to an appropriate regulated power source.
The MOTION DETECTION function is not
working
- Is “MOTION DETECTION” mode turned on?
- Check the setting of the MD AREA.
The image on the monitor flickers
- Make sure that the camera isn’t facing direct sunlight or fluorescent light. If necessary,change the camera
position.
Colors are not quite right.
- Check the settings in the WHITE BAL menu.
The SENS-UP does not work.
- Verify that the AGC setting in the EXPOSURE menu isn’t set to OFF.
- Check the SHUTTER setting in the EXPOSURE menu.
B.1 IR level adjustment
The IR level is preset at the factory. However, an adjustment potentiometer is provided on the OSD control board for environments
where the image brightness in dark conditions is not satisfactory after performing a Software Setup of the camera. To adjust the IR
level of the camera:
1.
With the camera operating in a dark environment, remove the camera dome to access the OSD control board.
2.
While observing the video image from the camera, use a #1 phillips screwdriver to turn the IR level adjustment
potentiometer clockwise and/or counter-clockwise until the image brightness is acceptable.
IR LED gain
adjustment
OSD Joystick
3.
Video test port
Reinstall the camera dome.
High Performance 700TVL CCTV Dome Camera User Manual
17
APPENDIX C: DIMENSIONS
APPENDIX C
Camera Dimensions
BLK-CPV700RH
2.81”
4.86”
Ø4.44”
Ø4.21”
Ø5.94”
Ø4.88”
18