Rev. 10/13

User Instructions

©2013 ADJ Products, LLC all rights reserved. Information,

specifications, diagrams, images, and instructions herein are subject to change without notice. ADJ Products, LLC logo and identifying product names and numbers herein are trademarks of ADJ Products, LLC. Copyright protection claimed includes all forms and matters of copyrightable materials and information now allowed by statutory or judicial law or hereinafter granted.

Product names used in this document may be trademarks or registered trademarks of their respective companies and are hereby acknowledged. All non-ADJ Products, LLC brands and product names are trademarks or registered trademarks of their respective companies.

ADJ Products, LLC and all affiliated companies hereby dis-

claim any and all liabilities for property, equipment, building, and electrical damages, injuries to any persons, and direct or indirect economic loss associated with the use or reliance of any information contained within this document, and/or as a result of the improper, unsafe, unsufficient and negligent assembly, installation, rigging, and operation of this product.

FREQ Matrix Introduction

Unpacking:

Thank you for purchasing the FREQ Matrix by ADJ Products, LLC. Every FREQ Matrix has been thoroughly tested and has been shipped in perfect operating condition. Carefully check the shipping carton for damage that may have occurred during shipping. If the carton appears to be damaged, carefully inspect your fixture for any damage and be sure all accessories necessary to operate the unit has arrived intact. In the case damage has been found or parts are missing, please contact our toll free customer support number for further instructions. Do not return this unit to your dealer without first contacting customer support.

Introduction:

The FREQ Matrix is part of ADJ’s continuing pursuit for creating high quality affordable intelligent fixtures. The FREQ Matrix is a revolutionary 16-zone LED strobe. The unit has 4 operating modes;

Sound Active (with adjustable sound sensitivity), Show Mode, Manual

Mode, or DMX Control. This unit can be used as a stand alone fixture, or in a Master/Slave configuration. This fixture is suitable for theaters, studios, retail stores, and other similar locations.

Customer Support:

ADJ Products, LLC provides a toll free customer support line, to provide set up help and to answer any question should you encounter problems during your set up or initial operation.

You may also visit us on the web at www.adj.com for any comments or suggestions. Service Hours are Monday through Friday 8:00 a.m. to

4:30 p.m. Pacific Standard Time.

Voice:

Fax:

E-mail:

(800) 322-6337

(323) 582-2941 [email protected]

Warning!

To prevent or reduce the risk of electrical shock or fire, do not expose this unit to rain or moisture.

Caution!

There are no user serviceable parts inside this unit. Do not attempt any repairs yourself, doing so will void your manufactures warranty. In the unlikely event your unit may require service please contact

ADJ Products, LLC.

PLEASE recycle the shipping carton when ever possible.

ADJ Products, LLC - www.adj.com - FREQ Matrix Instruction Manual Page 2

FREQ Matrix General Instructions

To optimize the performance of this product, please read these operating instructions carefully to familiarize yourself with the basic operations of this unit. These instructions contain important safety information regarding the use and maintenance of this unit. Please keep this manual with the unit, for future reference.

FREQ Matrix Features

• Built in Microphone

• 4 DMX Channel Modes: 1 Channel Mode, 2 Channel Mode, 16

Channel Mode, & 18 Channel Mode

• 12 Show Modes

• 4 Operating Modes - Sound Active, Show Mode, Manual Mode,

and DMX Control

• Sound Sensitivity Adjustable

• UC3 Remote Control Compatiable (Not Included)

• Power Cord Daisy Chaining. See page 18.

FREQ Matrix Warranty Registration

The FREQ Matrix carries a 3 year (1095 days) limited warranty. Please fill out the enclosed warranty card to validate your purchase and warranty. You may also register your product online at www.adj.com. All returned service items whether under warranty or not, must be freight pre-paid and accompany a return authorization (R.A.) number. If the unit is under warranty you must provide a copy of your proof of purchase invoice. Please contact ADJ Products, LLC customer support for a R.A. number.

FREQ Matrix Installation

The unit should be mounted using a mounting clamp (not provided), affixing it to the mounting bracket that is provided with the unit.

Always ensure that the unit is firmly fixed to avoid vibration and slipping while operating. Always ensure that the structure to which you are attaching the unit is secure and is able to support a weight of 10 times the unit’s weight. Also, always use a safety cable that can hold

12 times the weight of the unit when installing the fixture.

The equipment must be installed by a professional, and it must be installed in a place where it is out of the reach of people’s grasp.

ADJ Products, LLC - www.adj.com - FREQ Matrix Instruction Manual Page 3

FREQ Matrix Safety Precautions

• To reduce the risk of electrical shock or fire, do not expose this unit

rain or moisture

• Do not spill water or other liquids into or on to your unit.

• Do not attempt to operate this unit if the power cord has been

frayed or broken. Do not attempt to remove or break off the ground

prong from the electrical cord. This prong is used to reduce the risk

of electrical shock and fire in case of an internal short.

• Disconnect from main power before making any type of connection.

• Do not remove the cover under any conditions. There are no user

serviceable parts inside.

• Never operate this unit when it’s cover is removed.

• Never plug this unit in to a dimmer pack

• Always be sure to mount this unit in an area that will allow proper

ventilation. Allow about 6” (15cm) between this device and a wall.

• Do not attempt to operate this unit, if it becomes damaged.

• This unit is intended for indoor use only, use of this product out`

doors voids all warranties.

• During long periods of non-use, disconnect the unit’s main power.

• Always mount this unit in safe and stable matter.

• Power-supply cords should be routed so that they are not likely to

be walked on or pinched by items placed upon or against them,

paying particular attention to the point they exit from the unit.

• Cleaning -The fixture should be cleaned only as recommended by

t he manufacturer. See page 18 for cleaning details.

• Heat -The appliance should be situated away from heat sources

such as radiators, heat registers, stoves, or other appliances (inclu-

d ing amplifiers) that produce heat.

• The fixture should be serviced by qualified service personnel when:

A. The power-supply cord or the plug has been damaged.

B. Objects have fallen, or liquid has been spilled into the appliance.

C. The appliance has been exposed to rain or water.

D. The appliance does not appear to operate normally or exhibits a

marked change in performance.

FREQ Matrix Set Up

P

ower Supply:

The ADJ FREQ Matrix contains a automatic voltage switch, which will auto sense the voltage when it is plugged into the power source. With this switch there is no need to worry about the correct power voltage, this unit can be plugged in anywhere.

DMX-512:

DMX is short for Digital Multiplex. This is a universal protocol used as a form of communication between intelligent fixtures and controllers. A DMX controller sends DMX data instructions from the controller to the fixture. DMX data is sent as serial data that travels from fixture to fixture via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX fixtures (most controllers only have a DATA

“OUT” terminal).

DMX Linking: DMX is a language allowing all makes and models of different manufactures to be linked together and operate from a single controller, as long as all fixtures and the controller are DMX compliant. To ensure proper DMX data transmission, when using several

DMX fixtures try to use the shortest cable path possible. The order in which fixtures are connected in a DMX line does not influence the

DMX addressing. For example; a fixture assigned a DMX address of 1 may be placed anywhere in a DMX line, at the beginning, at the end, or anywhere in the middle. When a fixture is assigned a DMX address of 1, the DMX controller knows to send DATA assigned to address 1 to that unit, no matter where it is located in the DMX chain.

Data Cable (DMX Cable) Requirements (For DMX Operation):

The FREQ Matrix has 4 DMX Channel modes. The DMX address is set on the rear panel of the FREQ Matrix. Your unit and your DMX controller require a approved DMX-512 110 Ohm Data cable for data input and data output. We recommend Accu-Cable DMX cables. If you are making your own cables, be sure to use standard 110-120 Ohm shielded cable (This cable may be purchased at almost all professional sound and lighting stores). Your cables should be made with a male and female

XLR connector on either end of the cable. Also remember that DMX cable must be daisy chained and cannot be split.

ADJ Products, LLC - www.adj.com - FREQ Matrix Instruction Manual Page 4

Figure 1

ADJ Products, LLC - www.adj.com - FREQ Matrix Instruction Manual Page 5

SOUND

SOUND

REMOTE

CONTROL

INPUT

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

INPUT OUTPUT

REMOTE

CONTROL

INPUT

INPUT OUTPUT

1

2

3

POWER

COMMON

DMX +

DMX -

SOUND

3

1

2

POWER POWER

FREQ Matrix Set Up

Notice:

Be sure to follow figures two and three when making your own cables. Do not use the ground lug on the XLR connector. Do not connect the cable’s shield conductor to the ground lug or allow the shield conductor to come in contact with the XLR’s outer casing. Grounding the shield could cause a short circuit and erratic behavior.

COMMON

1

2

3

DMX +

DMX -

3

1

2

3

1

2

REMOTE

CONTROL

INPUT

INPUT OUTPUT

XLR Male Socket

1 Ground

2 Cold 2 Cold

1 Ground

Figure 2

REMOTE

CONTROL

INPUT

INPUT OUTPUT

XLR Pin Configuration

Pin 1 = Ground

Pin 2 = Data Compliment (negative)

3 Hot

3 Hot

Pin 3 = Data True (positive)

Figure 3

POWER POWER

Special Note: Line Termination.

When longer runs of cable are used, you may need to use a terminator on the last unit to avoid erratic behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is connected between pins 2 and 3 of a male XLR connector (DATA + and

DATA -). This unit is inserted in the female XLR connector of the last unit in your daisy chain to terminate the line. Using a cable terminator

(ADJ part number Z-DMX/T) will decrease the possibilities of erratic behavior.

1

3

2

Figure 4

5-Pin XLR DMX Connectors.

Some manufactures use 5-pin DMX-

512 data cables for DATA transmission in place of 3-pin. 5-pin DMX fixtures may be implemented in a 3-pin DMX line. When inserting standard 5-pin data cables in to a 3-pin line a cable adaptor must be used, these adaptors are readily available at most electric stores. The chart below details a proper cable conversion.

3-Pin XLR to 5-Pin XLR Conversion

Conductor

Ground/Shield

Data Compliment (- signal)

Data True (+ signal)

Not Used

Not Used

3-Pin XLR Female (Out)

Pin 1

Pin 2

Pin 3

5-Pin XLR Male (In)

Pin 1

Pin 2

Pin 3

Do Not Use

Do Not Use

ADJ Products, LLC - www.adj.com - FREQ Matrix Instruction Manual Page 6

POWER

FREQ Matrix System Menu

ADJ Products, LLC - www.adj.com - FREQ Matrix Instruction Manual Page 7

FREQ Matrix System Menu

ADDR

- DMX Address Setting via control board -

1. Press the MENU button until “ADDR” is displayed, press

ENTER.

2. “X” will now be displayed, “X” represents the displayed address.

Press the UP or DOWN buttons to find your desired address.

3. Press ENTER to confirm, then connect your DMX controller.

NOTE: If after you connect your DMX controller the unit does not fall into DMX mode, press and hold the MENU button for at least

3 seconds.

CHND

- This will let select your desired DMX channel mode.

1. Press the either the MENU button until “CHND” is displayed, press ENTER. Either “1CH”, “2CH”, “16CH” or “18CH” will be displayed

2. Press the UP or DOWN buttons to find your desired DMX channel mode and press ENTER to confim and exit.

SLND

- This will let you set unit as a master or slave in a master/slave configuration.

1. Press the MENU button until “SLND” is displayed, press

ENTER. Either “MAST”, “SL 1” or “SL 2” will be displayed.

2. Press the UP or DOWN buttons until your desired setting is displayed, press ENTER to confim.

NOTE: In a Master/Slave configuration you can set one fixture to Slave 1 (SL 1) and then set the next fixture to Slave 2 (SL 2), in doing this the fixtures will now have contrast movement to each other.

ADJ Products, LLC - www.adj.com - FREQ Matrix Instruction Manual Page 8

FREQ Matrix System Menu

SHND: SH 0 SH 12

- Show modes 0 - 12 & Manual show. Show mode can run with or without sound active mode on. Manual show is used in conjunction with knobs located on the rear of the unit. NOTE: When running the fixture as a

single fixture, it must be set to the Master setting.

See page 15 for Master setting.

1. Press the MENU button until “SHND” is displayed, press

ENTER.

2. “SH X” will now be displayed, “X” representing a number between 0-12 or “MANU” will be displayed. Shows 1-12 are preset shows, while “SH 0” is random show. “MANU” is Manual mode, in this mode you adjust the dimmer and strobe to your desire using the knobs located on the rear of the unit. Press the

UP or DOWN buttons to find your desired show.

3. Once you have found your desired show press ENTER, and then press and hold the MENU button for at least 3 seconds to confirm.

MANU

- In this mode you can manually control the dimmer and strobe rate. Unlike the Manual show located under the

Show Mode submenu, this Manual mode is NOT USED with the knobs located on the rear of the unit.

1. Press the MENU button until “MANU” is displayed, press

ENTER.

2. Either “DIMM” or “STRO” will now be displayed. Press the UP or DOWN buttons to switch between either setting.

3. When you have decided on what setting you would like to adjust first, press the ENTER button. Use the UP and DOWN buttons to make adjustments. Once you have made your desired adjustments press ENTER.

4. Once you have finished with your adjustments DO NOT leave this function. If you press the MENU button, all adjustments will

ADJ Products, LLC - www.adj.com - FREQ Matrix Instruction Manual Page 9

FREQ Matrix System Menu

be lost and you will have to start over.

SOUN

- In this submenu you can activate sound active mode. NOTE: When running the fixture as a single fixture, it

must be set to the Master setting.

See page 15 for Master setting.

1. Press the MENU button until “SOUN” is displayed, press

ENTER.

2. Either “ON” or “OFF” will now be displayed. Press the UP or

DOWN buttons to select one or the other.

3. When you have made your selection, press the ENTER, and then press and hold the MENU button for at least 3 seconds to confirm.

SENS

- Sound sensitivity control.

1. Press the MENU button until “SENS” is displayed, press ENTER.

2. The display will show a number between 0-100. Press the UP or

DOWN buttons to adjust the sound sensitivity. 0 being the least sensitive and 100 the most sensitive.

3. Press the ENTER, and then press and hold the MENU button for at least 3 seconds to confirm.

DNST

- This mode can be used as a precaution mode, that in case the DMX signal is lost, the operating mode chosen in the setup is the running mode the fixture will go into when the DMX signal is lost. You can also set this as the operating mode you would like the unit to return to when power is applied.

1. Press the MENU button until “DNST” is displayed, press

ENTER.

2. Either “MASL”, “BLND”, or “LAST” will be displayed. Choose

ADJ Products, LLC - www.adj.com - FREQ Matrix Instruction Manual Page 10

FREQ Matrix System Menu

an operating mode you would like the unit to start up in when power is applied or the DMX signal is lost.

• MASL (Master Slave) - If the DMX signal is lost or power is applied, the unit will automatically go into Master Slave mode.

• BLND (Blackout) - If the DMX signal is lost or power is applied, the unit will automatically go into stand by mode.

• LAST (Last State) - If the DMX signal is lost the fixture will stay in the last DMX set up. If power is applied and this mode is set, the unit will automatically go into the last DMX set up.

3. Press ENTER to confirm your desired set up.

LED

- With this function the LED display will turn off after

2 minutes.

1. Press the MENU button until “LED” is displayed, press ENTER.

2. Either “ON” or “OFF” will now be displayed. Press the UP or

DOWN buttons to select “ON” to keep the LED display on at all times, or “OFF” to allow the LED display to turn off after 2 minutes. Press any button to turn the LED display on again.

3. Press ENTER to confirm your selection.

DISP

- This will “flip” the LED display

1. Press the MENU button until “DISP” is displayed, press

ENTER.

2. When “DISP” is displayed the LED display will remain normal, when “DSIP” is displayed, the LED display will be “flipped”.

Use the ENTER button to find your desired display set up, then press MENU to confirm and exit.

TEST

- This function will run a self test program.

1. Press the MENU button until “TEST” is displayed, press

ADJ Products, LLC - www.adj.com - FREQ Matrix Instruction Manual Page 11

FREQ Matrix System Menu

ENTER.

2. The fixture will now run a self test. Press the MENU button to exit.

TEMP

- With this function you can check the current temperature of the fixture.

1. Tap the MENU button until “TEMP” is displayed, press

ENTER.

2. The current temperature of the fixture will now be displayed.

Press MENU to exit.

FHRS

- With this function you can display the running time of the unit.

1. Press the MENU button until “FHRS” is displayed, press

ENTER.

2. The running time of the fixture will now be displayed. Press

MENU to exit.

VER

- This will display the software version

1. Press the MENU button until “VER” is displayed. Press the

ENTER button and the software vesion will be displayed.

2. Press the MENU button to leave this function.

ADJ Products, LLC - www.adj.com - FREQ Matrix Instruction Manual Page 12

FREQ Matrix Operation

Universal DMX Control:

This function allows you to use a Elation

® universal DMX-512 controller to control the chases and patterns, dimmer and strobe. A DMX controller allows you to create unique programs tailored to your individual needs.

1. The FREQ Matrix has 4 DMX Modes; a 1 Channel Mode, 2

Channel Mode, 16 Channel Mode, & 18 Channel Mode. See

pages 16-17 for a detailed description of the DMX traits.

2. To control your fixture in DMX mode, follow the set-up procedures

on pages 8-9 as well as the set-up specifications that are

included with your DMX controller.

3. Use the controller’s faders to control the various DMX fixture traits.

This will allow you to create your own programs.

4. Follow the instructions on page 8 to select your desired DMX

Mode and to set the DMX address. After you have selected your

DMX mode and set the address, then connect your DMX control-

ler.

5. For longer cable runs (more than a 100 feet) use a terminator on

the last fixture.

6. For help operating in DMX mode consult the manual included

with your DMX controller.

Sound Active Mode:

This mode allows a single unit or several units linked together, to run to the beat of the music. NOTE: When running

the fixture as a single fixture, it must be set to the Master setting.

See page 15 for Master setting.

1. Press the MENU button until

“SOUN” is displayed, and press

ENTER.

2.

Press the UP or DOWN buttons until “ON” is displayed and press

ENTER, and then press and hold the MENU button to confirm.

3. To adjust the sound sensitivity press the MENU button until

“SENS” is displayed. Use the UP or DOWN buttons to adjust sen-

sitivity. See page 10 for more info.

4. The optional UC3 Controller (not included) may be used to con-

trol different functions including blackout. See page 15 for UC3

controls and functions.

Show Mode:

This mode allows a single unit or several units linked together, to run a selected show. NOTE: When running the fixture as

a single fixture, it must be set to the Master setting. See page 15

ADJ Products, LLC - www.adj.com - FREQ Matrix Instruction Manual Page 13

FREQ Matrix Operation

for Master setting.

1. Press the MENU button until

“SHND” is displayed, and press

ENTER.

2.

Press the UP or DOWN buttons until you find your desired show,

press ENTER, then press and hold the MENU button to confirm.

Please see page 9 for more info about Show Mode.

3. The optional UC3 Controller (not included) may be used to con-

trol different functions including blackout. See page 15 for UC3

controls and functions.

Manual Mode:

This mode allows a single unit to run a manual set up.

1. Press the MENU button until

“MANU” is displayed, and press

ENTER.

2. Either “DIMM” or “STRO” will now be displayed. Press the UP or

DOWN buttons to switch between either setting.

3. When you have decided on what setting you would like to adjust

first, press the ENTER button. Use the UP and DOWN buttons to

make adjustments. Once you have made your desired adjust-

ments press ENTER.

4. Once you have finished with your adjustments DO NOT leave this

submenu. If you press the MENU button, all adjustments will be-

lost and you will have to start over.

5. The optional UC3 Controller (not included) may be used to con-

trol different functions including blackout. See page 15 for UC3

controls and functions.

FREQ Matrix Master-Slave Set Up

Master-Slave Operation:

This function will allow you to link up to 16 units together and operate without a controller. In Master-Slave operation one unit will act as the controlling unit and the others will react to the controlling units programs. Any unit can act as a Master or as a

Slave.

1. Using appropriate XLR cables, daisy chain your units together via

the XLR connector on the rear of the units. Remember the Male

XLR connector is the input and the Female XLR connector is the

output. The first unit in the chain (master) will use the female XLR

con nector only - The last unit in the chain will use the male XLR con nector only. For longer cable runs we suggest a terminator at

the last fixture.

2. Set the Master unit to your desired operational mode. After you

have set your desired operational mode, press the MENU button

until “SLND” is displayed, and Press ENTER. Use the UP or

DOWN buttons to find the “MAST” setting and press ENTER.

3. On the slave units tap the MENU button until “SLND” is display-

ed, and Press ENTER. Use the UP or DOWN buttons to switch

between either “SL 1” or “SL 2”. Once you have made your

choice, press ENTER. For more info see page 8.

4. The slave units will now follow the Master unit.

5. The optional UC3 Controller (not included) may be used to con-

trol different functions including blackout. See UC3 Control below.

FREQ Matrix UC3 Control

Blackout Blackout the unit

Mode

Strobe(LED OFF)

Select Show (Show 1-12).

Show(LED ON)

ADJ Products, LLC - www.adj.com - FREQ Matrix Instruction Manual Page 14

ADJ Products, LLC - www.adj.com - FREQ Matrix Instruction Manual Page 15

FREQ Matrix 1 Channel Mode

Channel Value Function

1 SHOWS

0 - 7 BLACKOUT

8 - 27 SHOW 1

28 - 47 SHOW 2

48 - 67 SHOW 3

68 - 87 SHOW 4

88 - 107 SHOW 5

108 - 127 SHOW 6

128 - 147 SHOW 7

148 - 167 SHOW 8

168 - 187 SHOW 9

188 - 207 SHOW 10

208 - 227 SHOW 11

228 - 247 SHOW 12

248 - 255 RANDOM SHOW

Note: All shows are sound active when a music source is present.

FREQ Matrix 2 Channel Mode

Channel Value Function

1 MASTER DIMMER

0 - 255 0% - 100%

2 STROBING

0 - 8 NO FUNCTION

9 - 255 STROBING SLOW - FAST

FREQ Matrix 16 Channel Mode

Channel Value Function

1 - 16 DIMMER

0 - 255 0% - 100%

FREQ Matrix 18 Channel Mode

Channel Value Function

1 - 16 DIMMER

0 - 255 0% - 100%

17 MASTER DIMMER

0 - 255 0% - 100%

18 STROBING

0 - 8 NO FUNCTION

9 - 131 STROBING SLOW - FAST

132 - 139 NO FUNCTION

140 - 181 SLOW OPEN - FAST CLOSE

182 - 189 NO FUNCTION

190 - 231 FAST OPEN - SLOW CLOSE

232 - 239 NO FUNCTION

240 - 247 SOUND ACTIVE STROBING

248 - 255 NO FUNCTION

FREQ Matrix Photometric Chart

ADJ Products, LLC - www.adj.com - FREQ Matrix Instruction Manual Page 16 ADJ Products, LLC - www.adj.com - FREQ Matrix Instruction Manual Page 17

FREQ Matrix Power Cord Daisy Chain

With this feature you can connect the fixtures to one another using the IEC input and output sockets. The quantity that can be connected is 4 fixtures maximum. After 4 fixtures you will need to use a new power outlet. They must be the same fixtures. DO NOT mix fixtures.

FREQ Matrix Fuse Replacement

Locate and remove the unit’s power cord. Once the cord has been removed located the fuse holder located inside the power socket.

Insert a flat-head screw driver into the power socket and gently pry out the fuse holder. Remove the bad fuse and replace with a new one. The fuse holder has a built-in socket for a spare fuse be sure not to confuse the spare fuse with active fuse.

FREQ Matrix Cleaning

Due to fog residue, smoke, and dust cleaning the internal and external optical lenses must be carried out periodically to optimize light output.

1. Use a soft cloth to wipe down the outside casing.

Cleaning frequency depends on the environment in which the fixture operates (i.e. smoke, fog residue, dust, dew).

FREQ Matrix Trouble Shooting

Listed below are a few common problems the user may encounter, with solutions.

Unit not responding to DMX:

1. Check that the DMX cables are connected properly and are

wired correctly (pin 3 is “hot”; on some other DMX devices

pin 2 may be ‘hot’). Also, check that all cables are connected

to the right connectors; it does matter which way the inputs

and outputs are connected.

Unit does not respond to sound:

1. Quiet or high pitched sounds will not activate the unit.

If problems are not resolved; Contact ADJ Products, LLC for service.

1-800-322-6337

ADJ Products, LLC - www.adj.com - FREQ Matrix Instruction Manual Page 18

FREQ Matrix Warranty

MANUFACTURER’S LIMITED WARRANTY

A. ADJ Products, LLC hereby warrants, to the original purchaser, ADJ Products, LLC products to be free of manufacturing defects in material and workmanship for a prescribed period from the date of purchase (see specific warranty period on reverse). This warranty shall be valid only if the product is purchased within the United States of America, including possessions and territories. It is the owner’s responsibility to establish the date and place of purchase by acceptable evidence, at the time service is sought.

B. For warranty service you must obtain a Return Authorization number (RA#) before sending back the

product–please contact ADJ Products, LLC Service Department at 800-322-6337. Send the product only to the ADJ Products, LLC factory. All shipping charges must be pre-paid. If the requested repairs or service (including parts replacement) are within the terms of this warranty, ADJ Products, LLC will pay return shipping charges only to a designated point within the United States. If the entire instrument is sent, it must be shipped in it’s original package. No accessories should be shipped with the product. If any accessories are shipped with the product, ADJ Products, LLC shall have no liability whatsoever for loss of or damage to any such accessories, nor for the safe return thereof.

C. This warranty is void if the serial number has been altered or removed; if the product is modified in any manner which ADJ Products, LLC concludes, after inspection, affects the reliability of the product; if the product has been repaired or serviced by anyone other than the ADJ Products, LLC factory unless prior written authorization was issued to purchaser by ADJ Products, LLC; if the product is damaged because not properly maintained as set forth in the instruction manual.

D. This is not a service contract, and this warranty does not include maintnance, cleaning or periodic check up. During the period specified above, ADJ Products, LLC will replace defective parts at its expense with new or refurbished parts, and will absorb all expenses for warranty service and repair labor by reason of defects in material or workmanship. The sole responsibility of ADJ Products, LLC under this warranty shall be limited to the repair of the product, or replacement thereof, including parts, at the sole discretion of ADJ Products, LLC. All products covered by this warranty were manufactured after August

15, 2012, and bear indentifying marks to that effect.

E. ADJ Products, LLC reserves the right to make changes in design and/or improvements upon its products without any obligation to include these changes in any products theretofore manufactured.

No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with products described above. Except to the extent prohibited by applicable law, all implied warranties made by ADJ Products, LLC in connection with this product, including warranties of merchantability or fitness, are limited in duration to the warranty period set forth above. And no warranties, whether expressed or implied, including warranties of merchantability or fitness, shall apply to this product after said period has expired. The consumer’s and/or Dealer’s sole remedy shall be such repair or replacement as is expressly provided above; and under no circumstances shall ADJ Products, LLC be liable for any loss or damage, direct or consequential, arising out of the use of, or inability to use, this product.

This warranty is the only written warranty applicable to ADJ Products, LLC Products and supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore

published.

MANUFACTURER’S LIMITED WARRANTY PERIODS:

• Lighting Products = 1-year (365 days) Limited Warranty (Such as: Special Effect Lighting, Intelligent

Lighting, UV lighting, Strobes, Fog Machines, Bubble Machines, Mirror Balls, Par Cans, Trussing,

Lighting Stands etc. excluding LED and lamps)

• Laser Products = 90-Day Limited Warranty

• L.E.D. Products = 3-year (1095 days) Limited Warranty (excluding motors, PCB boards, and power

supplies, which have a 1-year (365 day Limited Warranty) and batteries which have a 180 day

limited warranty). Only the L.E.D.s carry a 3-year warranty

ADJ Products, LLC - www.adj.com - FREQ Matrix Instruction Manual Page 19

FREQ Matrix Notes FREQ Matrix Notes

ADJ Products, LLC - www.adj.com - FREQ Matrix Instruction Manual Page 20 ADJ Products, LLC - www.adj.com - FREQ Matrix Instruction Manual Page 21

FREQ Matrix Specifications

Model: FREQ Matrix

Voltage:

LEDs:

100V~240V 50/60Hz

16 x 5W White LEDs

Power Consumption: 107W

Fuse: 7Amp

Power Cord Daisy Chain: 4 Fixtures Max.

Weight:

Dimensions

Colors:

DMX Channels:

Working Position:

:

8lbs./ 3.6Kgs.

11.75” (L) x 11.5” (W) x 4.75” (H)

295 x 291 x 115mm

White

4 DMX Channel Modes: 1 Channel

Mode, 2 Channel Mode, 16 Chan- nel Mode, & 18 Channel Mode.

Any safe working position

Warranty: 3 Years (1095 days)

Auto Sensing Voltage:

This fixture contains a automatic voltage switch, which will auto sense the voltage when it is plugged into the power source.

Please Note: Specifications and improvements in the design of this unit and this manual are subject to change without any prior written notice.

ADJ Products, LLC - www.adj.com - FREQ Matrix Instruction Manual Page 22

ADJ Products, LLC

6122 S. Eastern Ave. Los Angeles, CA 90040 USA

Tel: 323-582-2650 / Fax: 323-725-6100

Web: www.adj.com / E-mail: [email protected]

A.D.J. Supply Europe B.V.

Junostraat 2

6468 EW Kerkrade

Netherlands [email protected] / www.adj.eu

Tel: +31 45 546 85 00 / Fax: +31 45 546 85 99