Pro Shop LED LitePAR Pro Tri-18 User manual

LED LitePAR Pro Tri-18
User Manual
LED LitePAR Pro Tri-18 DMX
18 High Powered Tri-Colour LEDs
www.showtech.com.au
1
LED LitePAR Pro Tri-18
Table of Contents
1. Safety instructions…………………………………………………………3
1.1 Overhead rigging …………………………………………………….4
1.2 Power Connection …………………………………………………..6
1.3 Cleaning and Maintenance ……………………………………..6
2. Menu Navigation ............................................................7
3. DMX Allocation ...............................................................9
4. Technical Specifications ..................................................11
2
LED LitePAR Pro Tri-18
1. Safety Instructions
FOR SAFE AND EFFICIENT OPERATION
Be careful with heat and extreme temperature.
Avoid exposing it to direct rays of sun near a heating appliance.
Do not put it in a temperature below 41°F/5°C, or exceeding 95°F/35°C.
Keep away from humidity, water and dust.
Do not place the set in a location with a high humidity or lots of dust.
Containers with water should not be placed on the set.
Keep away from sources of hum and noise
Such as transformer motor, tuner, TV set and amplifier.
To avoid placing on un-stable location
Select a level and stable location to avoid vibration.
Do not use chemicals or volatile liquids for cleaning
Use a dry cloth to wipe off the dust, or a wet soft cloth for stubborn dirt.
NO USER SERVICABLE PARTS INSIDE.
If unit is out of service please contact your point of purchase.
If any troubles arise, remove the power plug and contact your Pro Shop
representative for repair. Do not open the cabinet by yourself, it might result a
danger of electric shock.
Take care with the power cable. Never pull the power cable to remove the plug from
the receptacle, be sure to hold the plug.
3
LED LitePAR Pro Tri-18
When not using the unit for an extended period of time be sure to disconnect the
plug form the receptacle.
1.1 . Overhead Rigging
This item must be built in a way that it can hold 10 times more of its weight for 1
hour without causing any damages. The installation must be secured with a
secondary safety attachment. The Safety attachment has to be constructed in a way
that no part of the installation can fall down. When rigging, de-rigging or servicing
the fixture staying in the area below the installation place, on bridges, under high
working places and other endangered areas us forbidden. Before taking the device in
operation, the installation must be approved by an expert. The operator has to make
sure that safety-relating and machine-technical installations are approved by a skilled
person once a year.
IMPORTANT! OVERHEAD RIGGING REQUIRES EXTENSIVE EXPERIENCE.
Including (but not limited to) calculating working load limits, installation material
being used, and periodic safety inspection of all installation material and the
projector. If you lack these qualifications, do not attempt the installations yourself,
but instead use a professional structural rigger. Improper installation can result in
bodily injury and/or damage to property.
Use only professional trussing system if the item shall be lowered from the ceiling or
high joists. Never let the device swing freely in a room.
CAUTION: Overhead Items may cause serious injuries when crashing down!! If there
is concern about the safety then DO NOT INSTALL the device.
4
LED LitePAR Pro Tri-18
DANGER OF FIRE!
When installing the device, make sure there is no highly-flammable material
(decoration articles, etc) within a distance of min. 0.5m.
Mount the projector with the mounting bracket to your trussing system using an
appropriate clamp.
For overhead use, always install a safety-rope that can hold at least 10 times the
weight of the fixture. You must only use safety –ropes with quick links with screw
cap. Pull the safety-rope through the hole in the mounting bracket and over the
trussing system or a safe fixation spot. Insert the end in the quick link and tighten the
safety screw. The maximum drop distance must never exceed 20cm
A safety rope which already held the strain of a crash or which is defective must not
be used again.
DANGER TO LIFE!
Before taking into operation for the first time, the installation has to be approved by
an expert.
5
LED LitePAR Pro Tri-18
1.2. Power Connection
!! CAUTION !!
Never leave this device running unattended!! Every person that is involved with this
item has to be qualified!!
Connect item with main plug. The voltage and frequency must exactly be the same as
stated on the device. The power plug must always be inserted without force.
1.3. Cleaning and Maintenance
Please make sure that safety-relating and machine-technical installations are
inspected by a skilled person once a year.
1.
2.
3.
Make sure before installing that all screws are tightly connected and not corroded.
There must be no deformations on the housings, fixations and installations spots
No damages must be showed on the power supply cables, material fatigue and
sediments
If the exterior of the unit is going to be cleaned, please use moist, lint free cloths.
Never use alcohol or solvents.
The Cooling fan must be cleaned monthly and check to ensure it is free of
obstructions.
To clean the interior of the device please use a vacuum cleaner or an air jet, however
we recommend cleaning the lenses weekly to ensure the best output from your unit.
6
LED LitePAR Pro Tri-18
2.0 Menu navigation
Menu Selection
Options
Auto Show
Auto Show 1
Extended Options
Auto Show Speed 0-100, slowfast
Allows the user to select in
built auto show
Auto Show 2
Auto Show 3
Auto Show 4
Auto Show 5
Static
Allows the user to select nonchanging output colours and
shades, as well as setting the
strobe function
Fixture Color
Fixture Color
Select R,G,B
select desired colour
Select S
Select S for Strobe
Select Mode C
C1: Red
C2: Green
C3: Blue
C4: Cyan
C5: Magenta
C6: Yellow
C7: White
7
LED LitePAR Pro Tri-18
Dimmer Mode
Allows the user to select from
4 options of dimming speeds
Off
Dimmer Speed off
Dimmer 1
Dimmer Speed Fast
Dimmer 2
Dimmer Speed Medium
Dimmer 3
Dimmer Speed Slow
Back Lite
On
LCD Backlight will remain on
Adjusts the setting of the
LCD back light
10s
LCD off after 10 seconds
20s
LCD off after 20 seconds
30s
LCD off after 30 seconds
DMX Address
DMX Address
001-512
Set the unit start address
DMX Channel
3 Channel Mode
Short RGB mode
Adjust the DMX mode of the
unit
4 Channel Mode
RGB + dimmer, strobe
9 Channel Mode
RGB + dimmer, strobe, macro
Master / Slave
Master
8
Master Mode
LED LitePAR Pro Tri-18
Allows the unit to be set in
slave mode to copy other
units on DMX chain
Slave
Slave Mode
3.0 DMX Allocation
9 Channels Mode:
CHANNEL
1
2
3
4
5
6
7
VALUE
000-255
000-255
000-255
000-255
000-010
011-030
031-050
051-070
071-090
091-110
111-130
131-150
151-170
171-200
201-205
206-210
211-215
216-220
221-225
226-230
231-235
236-240
241-245
246-250
251-255
000-009
010-255
000-051
052-101
FUNCTION
DIMMER 0% ~ 100%
Red 0% ~ 100%
Green 0% ~ 100%
Blue 0% ~ 100%
No Function
RED 100% / GREEN UP / BLUE 0%
RED DOWN / GREEN 100% / BLUE 0%
RED 0% / GREEN 100% / BLUE UP
RED 0% / GREEN DOWN / BLUE 100%
RED UP / GREEN 0% / BLUE 100%
RED 100% / GREEN 0% / BLUE DOWN
RED 100% / GREEN UP / BLUE UP
RED DOWN / GREEN DOWN / BLUE 100%
RED 100% / GREEN 100% / BLUE 100%
WHITE 1: 3200K
WHITE 2: 3400K
WHITE 3 4200K
WHITE 4: 4900K
WHITE 5: 5600K
WHITE 6: 5900K
WHITE 7: 6500 K
WHITE 8: 7200K
WHITE 9: 8000K
WHITE10: 8500K
WHITE11: 10000K
Strobe OFF
Flash speed: Slow ~ Fast
No Function
Auto Program 1
9
LED LitePAR Pro Tri-18
102-152
153-203
204-254
255
000-255
000-051
052-101
102-152
153-203
204-255
Auto Program 2
Auto Program 3
Auto Program 4
Auto Program 5
Speed of Auto Programs (Slow ~ Fast)
Default dimmer speed
Linear dimmer
Non-linear dimmer 1
Non-linear dimmer 2
Non-linear dimmer 3
4 Channels Mode:
CHANNEL
1
2
3
4
VALUE
000-255
000-255
000-255
000-255
FUNCTION
DIMMER 0% ~ 100%
Red: 0% ~ 100%
Green: 0% ~ 100%
Blue: 0% ~ 100%
3 Channels Mode:
CHANNEL
1
2
3
VALUE
000-255
000-255
000-255
FUNCTION
Red: 0% ~ 100%
Green: 0% ~ 100%
Blue: 0% ~ 100%
8
9
10
LED LitePAR Pro Tri-18
4.0 Technical Specifications
Power supply: 100 -240 V AC, 50/60 Hz
Power consumption: 48 W
DMX control channels: 9 / 4 / 3
DMX512 connection: 3-pin XLR
Number of LEDs: 18
Type of LEDs: 3 W Tri-colour
Beam angle: approx. 25°
Dimensions (LxWxH): 225 x 255 x 85 mm
Weight: 3.5 kg
Maximum ambient temperature Ta: 45°
Maximum housing temperature TC (steady state): 50° C
Fuse: F 2 A, 250 V
Please note: Every information is subject to change without prior
notice ©
11