ESIM264
GSM ALARM AND MANAGEMENT SYSTEM
INSTALLATION MANUAL
COMPLIES WITH EN 50131-1 GRADE 2, CLASS II REQUIREMENTS
Installation Manual v3.1
Valid for ESIM264 v7.15.00 and up
Safety instructions
Please read and follow these safety guidelines in order to maintain safety of operators and people around:
• GSM alarm & management system ESIM264 (also referenced as alarm system, system or device) has radio transceiver operating in GSM
850/900/1800/1900 bands.
• DO NOT use the system where it can be interfere with other devices and cause any potential danger.
• DO NOT use the system with medical devices.
• DO NOT use the system in hazardous environment.
• DO NOT expose the system to high humidity, chemical environment or mechanical impacts.
• DO NOT attempt to personally repair the system.
• System label is on the bottom side of the device.
GSM alarm system ESIM264 is a device mounted in limited access areas. Any system repairs must be done only by qualified,
safety aware personnel.
The system must be powered by main 16-24V 50 Hz ~1.5A max or 18-24V
1,5A max DC power supply which must be
approved by LST EN 60950-1 standard and be easily accessible nearby the device. When connecting the power supply to the
system, switching the pole terminals places does not have any affect.
Any additional devices linked to the system ESIM264 (computer, sensors, relays etc.) must be approved by LST EN 60950-1
standard.
Main power supply can be connected to AC mains only inside installation room
with automatic 2-pole circuit breaker capable of disconnecting circuit in the
event of short circuit or over-current condition. Open circuit breaker must have a
gap between connections of more than 3mm and the disconnection current 5A.
Phase
Null
PE
AC/DC
AC 230V
50 Hz/DC 24V
ESIM264
USB cable
Mains power and backup battery must be disconnected before any installation or tuning work starts. The system installation
or maintenance must not be done during stormy conditions
Backup battery must be connected via the connection which in the case of breaking would result in disconnection of one of
battery pole terminals. Special care must be taken when connecting positive and negative battery terminals. Switching the
pole terminals places is NOT allowed.
In order to avoid fire or explosion hazards the system must be used only with approved backup battery.
The device is fully turned off by disconnecting 2-pole switch off device of the main power supply and disconnecting backup
battery connector.
Fuse F1 type – Slow Blown 3A. Replacement fuses have to be exactly the same as indicated by the manufacturer.
If you use I security class computer for setting the parameters it must be connected to earth.
The WEEE (Waste Electrical and Electronic Equipment) marking on this product (see left) or its documentation indicates that
the product must not be disposed of together with household waste. To prevent possible harm to human health and/or the
environment, the product must be disposed on in an approved and environmentally safe recycling process. For further information on how to dispose of this product correctly, contact the system supplier, or the local authority responsible for waste
disposal in your area.
2
EN
MANUAL ELDES ESIM264 V3.1
Contents
1.GENERAL INFORMATION..........................................................................................................................................................6
1.1.Functionality.......................................................................................................................................................................................................6
1.2. Compatible Device Overview............................................................................................................................................................................6
1.3. Default Parameters & Ways of Parameter Configuration............................................................................................................................6
2. Technical Specifications........................................................................................................................................................12
2.1. Electrical & Mechanical Characteristics........................................................................................................................................................12
2.2. Main Unit, LED & Connector Functionality...................................................................................................................................................13
2.3. Wiring Diagrams...............................................................................................................................................................................................14
3.INSTALLATION....................................................................................................................................................................... 20
4. GENERAL OPERATIONAL DESCRIPTION ............................................................................................................................... 24
5. CONFIGURATION METHODS...................................................................................................................................................25
6.PASSWORDS........................................................................................................................................................................... 28
7. SYSTEM LANGUAGE............................................................................................................................................................... 29
8. USER PHONE NUMBERS........................................................................................................................................................ 30
8.1. System Control from any Phone Number.....................................................................................................................................................31
9. DATE AND TIME.......................................................................................................................................................................33
10. USER PASSWORDS................................................................................................................................................................. 34
11. iBUTTON KEYS....................................................................................................................................................................... 36
11.1. Adding and Removing iButton Keys............................................................................................................................................................. 36
12. ARMING AND DISARMING...................................................................................................................................................... 38
12.1. Free of Charge Phone Call.............................................................................................................................................................................. 38
12.2. SMS Text Message.......................................................................................................................................................................................... 39
12.3. EKB2 Keypad and User Password................................................................................................................................................................. 40
12.4. EKB3 Keypad and User Password................................................................................................................................................................. 41
12.5. iButton Key....................................................................................................................................................................................................... 42
12.6. EWK1/EWK2 Wireless Keyfob....................................................................................................................................................................... 42
12.7. Arm-Disarm by Zone....................................................................................................................................................................................... 43
12.8. Disabling and Enabling Arm/Disarm Notifications.................................................................................................................................... 44
13. EXIT AND ENTRY DELAY........................................................................................................................................................ 46
14.ZONES..................................................................................................................................................................................... 48
14.1. Zone Numbering.............................................................................................................................................................................................. 48
14.2. Zone Expansion............................................................................................................................................................................................... 48
14.3. 6-Zone Mode.................................................................................................................................................................................................... 48
14.4. ATZ (Advanced Technology Zone) Mode..................................................................................................................................................... 49
14.5. Zone Type Definitions.................................................................................................................................................................................... 50
14.6. Zone Attributes................................................................................................................................................................................................51
14.7. Bypassing and Activating Zones.................................................................................................................................................................. 54
14.8. Zone Names..................................................................................................................................................................................................... 54
14.9. Disabling and Enabling Zones........................................................................................................................................................................55
15. STAY MODE..............................................................................................................................................................................56
16.TAMPERS.................................................................................................................................................................................57
16.1. Tamper Names..................................................................................................................................................................................................57
17. ALARM INDICATIONS AND NOTIFICATIONS.......................................................................................................................... 58
17.1. Enabling and Disabling Alarm Notifications................................................................................................................................................ 59
18. PROGRAMMABLE (PGM) OUTPUTS....................................................................................................................................... 62
18.1. PGM Output Numbering................................................................................................................................................................................. 62
18.2. PGM Output Expansion................................................................................................................................................................................... 62
18.3. PGM Output Names......................................................................................................................................................................................... 63
18.4. Turning PGM Outputs ON and OFF................................................................................................................................................................ 63
18.5. PGM Output Control by Event and Scheduler............................................................................................................................................. 65
18.6. Wireless PGM Output Type Definitions........................................................................................................................................................ 66
19. WIRELESS DEVICES.................................................................................................................................................................67
19.1. Binding, Removing and Replacing Wireless Devicess............................................................................................................................... 67
19.2. Wireless Device Information and Signal Status Monitoring..................................................................................................................... 69
19.3. Disabling and Enabling Siren if Wireless Signal is Lost............................................................................................................................. 70
20.SIREN/BELL.............................................................................................................................................................................71
20.1. Bell Squawk.......................................................................................................................................................................................................72
20.2. Indication by EWS2 Indicators........................................................................................................................................................................72
20.3. EWF1 Interconnection.....................................................................................................................................................................................73
MANUAL ELDES ESIM264 V3.1
EN
3
21. BACKUP BATTERY, MAINS POWER SUPPLY STATUS MONITORING AND MEMORY...............................................................74
22. GSM CONNECTION STATUS MONITORING ..............................................................................................................................77
23.PARTITIONS........................................................................................................................................................................... 78
23.1. Zone Partition.................................................................................................................................................................................................. 78
23.2. User Phone Number Partition....................................................................................................................................................................... 78
23.3. Keypad Partition and Keypad Partition Switch........................................................................................................................................... 79
23.4. User Password Partition............................................................................................................................................................................... 80
23.5. iButton Key Partition...................................................................................................................................................................................... 80
23.6. EWK1/EWK2 Wireless Keyfob Partition....................................................................................................................................................... 80
24. TEMPERATURE SENSORS.......................................................................................................................................................81
24.1. Adding, Removing and Replacing Temperature Sensors......................................................................................................................... 81
24.2. Setting Up MIN and MAX Temperature Boundaries. Temperature Info SMS........................................................................................ 81
25. REMOTE LISTENING AND 2-WAY VOICE COMMUNICATION................................................................................................... 83
26. SYSTEM INFORMATION. INFO SMS........................................................................................................................................ 84
26.1. Periodic Info SMS............................................................................................................................................................................................. 84
27. SYSTEM NOTIFICATIONS....................................................................................................................................................... 86
27.1. SMSC (Short Message Service Center) Phone Number............................................................................................................................. 89
28. EVENT LOG............................................................................................................................................................................. 90
29. INDICATION OF SYSTEM FAULTS............................................................................................................................................91
30. MONITORING STATION........................................................................................................................................................... 93
30.1. Data Messages – Events................................................................................................................................................................................. 94
30.2.Communication................................................................................................................................................................................................ 98
31. ELDES WIRED DEVICES........................................................................................................................................................ 108
31.1. RS485 Interface............................................................................................................................................................................................108
31.2. 1-Wire Interface..............................................................................................................................................................................................121
31.3. Modules Interface..........................................................................................................................................................................................121
32. ELDES WIRELESS DEVICES.................................................................................................................................................. 126
32.1. EWT1 - Wireless Transmitter-Receiver...................................................................................................................................................... 126
32.2. EW1 - Wireless Zone & PGM Output Expansion Module......................................................................................................................... 127
32.3. EWP1 – Wireless Motion Detector.............................................................................................................................................................. 129
32.4. EWD1 – Wireless Magnetic Door Contact.................................................................................................................................................. 131
32.5. EWK1 - Wireless Keyfob............................................................................................................................................................................... 133
32.6. EWS1 – Wireless Indoor Siren...................................................................................................................................................................... 135
32.7. EWS2 – Wireless Outdoor Siren................................................................................................................................................................... 137
32.8. EW1B - Battery-Powered Wireless Zone & PGM Output Expansion Module...................................................................................... 140
32.9. EWF1 - Wireless Smoke Detector............................................................................................................................................................... 143
32.10. EWK2 - Wireless Keyfob.............................................................................................................................................................................. 148
32.11. EWD2 - Wireless Door Contact/Shock Sensor/Water Sensor................................................................................................................151
32.12. EWS3 - Wireless Indoor Siren..................................................................................................................................................................... 155
33. REMOTE SYSTEM RESTART..................................................................................................................................................159
34. TECHNICAL SUPPORT ......................................................................................................................................................... 160
34.1.Troubleshooting............................................................................................................................................................................................ 160
34.2. Restoring Default Parameters.................................................................................................................................................................... 160
34.3. Updating the Firmware via USB Cable Locally......................................................................................................................................... 160
34.4. Updating Firmware via GPRS Connection Remotely............................................................................................................................... 161
34.5. Frequently Asked Questions....................................................................................................................................................................... 162
35. RELATED PRODUCTS........................................................................................................................................................... 164
4
EN
MANUAL ELDES ESIM264 V3.1
Limited Liability
The buyer must agree that the system will reduce the risk of fire, theft, burglary or other dangers but does not guarantee against such
events.
“ELDES UAB” will not take any responsibility regarding personal or property or revenue loss while using the system.
“ELDES UAB” liability according to local laws does not exceed value of the purchased system. “ELDES UAB” is not affiliated with any of the
cellular providers therefore is not responsible for the quality of cellular service.
Manufacturer Warranty
The system carries a 24-month warranty by the manufacturer “ELDES UAB”. Warranty period starts from the day the system has been
purchased by the end user. The warranty is valid only if the system has been used as intended, following all guidelines listed in the manual
and within specified operating conditions. Receipt must be kept as a proof of purchase date.
The warranty is voided if the system has been exposed to mechanical impact, chemicals, high humidity, fluids, corrosive and hazardous
environments or other force majeure factors.
Package Content
1. ESIM264..................................................... qty. 1
2. Microphone.................................................qty.1
3. SMA antenna............................................. qty. 1
4. Buzzer......................................................... qty. 1
5. Back-up battery connection wire.......... qty. 1
6. User manual............................................... qty. 1
7. Resistors 5,6kΩ.........................................qty. 6
8. Resistors 3,3kΩ.........................................qty. 6
9. Plastic standoffs.......................................qty. 4
About Installation Manual
This document describes detailed installation and operation process of alarm system ESIM264. It is very important to read the installation
manual before starting to use the system.
Copyright © “ELDES UAB”, 2013. All rights reserved
It is not allowed to copy and distribute information in this document or pass to a third party without advanced written authorization
by “ELDES UAB”. “ELDES UAB” reserves the right to update or modify this document and/or related products without a warning.
Hereby, “ELDES UAB” declares that this GSM alarm and management system ESIM264 is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. The declaration of conformity may be consulted at www.eldes.lt
MANUAL ELDES ESIM264 V3.1
EN
5
1.GENERAL INFORMATION
1.1. Functionality
ESIM264 – micro-controller based alarm system for houses, cottages, country homes, garages and other buildings, also capable of managing electrical appliances via cellular GSM/GPRS network. It can also be used as Intercom system.
Examples of using the system:
• Property security.
• Alarm switch.
• Thermostat, heating and air-conditioner control, temperature monitoring.
• Lighting, garden watering, water pump and other electrical equipment control via SMS text messages.
• Remote listening to what is happening in the secured area.
• Main 230V power status with SMS text message.
• Two-way intercom device via GSM network.
1.2. Compatible Device Overview
Wired Devices
Description
Device
EKB2
LCD keypad
4*
Max. Connectable Devices
EKB3
LED keypad
4*
EA1
EA2
EPGM1
EPGM8
Audio output module with 3,5mm jack
Audio amplifier module 1W 8Ω
16 zone and 2 PGM output expansion module
8 PGM output expansion module
1**
1**
1
1**
Device
EW1
EW1B
EWP1
EWD1
EWD2
EWK1****
EWK2****
EWS1
EWS2
EWS3
EWF1
Wireless Devices
Description
Wireless 2 zone and 2 PGM output expansion module
Battery-powered wireless 2 zone and 2 PGM output expansion module
Wireless motion detector
Wireless magnetic door contact
Wireless magnetic door contact/shock sensor/water sensor
Wireless keyfob with 4 buttons
Wireless keyfob with 4 buttons
Wireless indoor siren
Wireless outdoor siren
Wireless indoor siren
Wireless smoke detector
Max. Connectable Devices
16***
16***
16***
16***
16***
5***
5***
16***
16***
16***
16***
* - A mixed combination of EKB2 and EKB3 keypads is supported. The combination can consist of up to 4 keypads in total.
** - Only 1 of these modules can be connected at a time if the module slots are implemented in ESIM264 unit.
*** - A mixed combination of wireless devices is supported. The combination can consist of up to 32 wireless devices in total.
**** - A mixed combination of EWK1 and EWK2 keyfobs is supported. The combination can consist of up to 5 keyfobs in total.
1.3. Default Parameters & Ways of Parameter Configuration
Main Settings
Parameter
Default Value
Depends on firmware version according to user‘s location
SMS Password
0000
User Password 1
1111
User Password 2... 30
N/A
Administrator Password
1470
Duress Password
N/A
SGS Password
N/A
User 1... 5 Phone Number
N/A
Allow Control from Any Phone Number Disabled
Date & Time
N/A
Exit Delay - Partition 1... 4
15 seconds
Info SMS Scheduler
Frequency (days) – 1; Time - 11
SMS & EKB2 Menu Language
6
EN
Configurable by:
SMS
EKB2 EKB3
Configuration
Tool











































MANUAL ELDES ESIM264 V3.1
Zones
Parameter
Zone Name
Entry Delay
On-Board Zone Delay
EPGM1 Zone Delay
On-board Z1 Zone Type
On-board Z2... Z12 Zone Type
Keypad Zone Type
EPGM1 Zone Type
Wireless Zone Type
Virtual Zone Type
ATZ Mode
6-Zone Mode: Zone Connection Type
ATZ Mode: Zone Connection Type
On-board Zone Status
Keypad Zone Status
EPGM1 Zone Status
Wireless Zone Status
Virtual Zone Status
Stay attribute for individual zone
Arm-Disarm by Zone
Force atrribute for individual zone
Tamper Name
Chime
Default Value
SMS
Z1 - Zone 1; Z2 - Zone 2; Z3 - Zone 3; Z4 - Zone 4; Z5 Zone 5; Z6 - Zone 6
15 seconds
800 milliseconds
800 milliseconds
Delay
Instant
Instant
Instant
Depends on the connected wireless device
Interior Follower
Disabled
Type 1
Type 4
Enabled
Disabled
Enabled
Depends on the connected wireless device
Disabled
Disabled
N/A
Disabled
Tamper 1, Tamper 2, Tamper 3, Tamper 4, Tamper 5,
Tamper 6 etc.
Enabled
PGM Outputs
Parameter
PGM Output Name
Default Value
PGM Output Status
EPGM8 PGM Output Status
EPGM1 PGM Output Status
Wireless PGM Output Status
Wireless PGM Output Type
PGM Output Control by Event 1... 16
PGM Output Control by Event Management
Scheduler 1... 16
Disabled
Turn ON/OFF PGM Output by Timer
Using Module EPGM8 Mode
Disabled
Alarm Duration
EWS2 LED
Bell Squawk
Activate Siren if Wireless Device is Lost
1 minute
Disabled
Disabled
Disabled
MANUAL ELDES ESIM264 V3.1





Configuration
Tool


























































Configurable by:
EKB2 EKB3






Configuration
Tool



















Alarm Duration & Siren
Default Value
EKB2 EKB3

SMS
C1 – Controll1, C2 – Controll2, C3 – Controll3, C4 – Controll4 etc.
Disabled
Disabled
Disabled
Enabled
Depends on the connected wireless device
Disabled
Parameter
Configurable by:

Configurable by:
SMS
EKB2 EKB3









Configuration
Tool




EN
7
Parameter
Call in Case of Alarm
Send Alarm SMS to All Users Simultaneously
Send Arm/Disarm SMS to User 1... 5
Send Arm/Disarm SMS to All Selected
Users Simultaneously
Alarm Notifications & Arm/Disarm Notifications
Configurable by:
Default Value
SMS EKB2 EKB3
Enabled
Disabled

Enabled
Disabled

Main Power Status
Parameter
Default Value
Main Power Loss Delay
Main Power Restore Delay
30 seconds
120 seconds
Default Value
Temperature Sensor MIN
Temperature Sensor MAX
Allow adding New iButton Keys
0 °C
0 °C
Disabled
Parameter
General Alarm
System Disarmed
System Armed
Main Power Loss Event Enabled
Main Power Restore Event Enabled
Low Battery
Periodical Info
Tamper Alarm Event
Battery Failed
System Started
Wireless Signal Loss
Temperature Fallen
Temperature Exceeded
System Shutdown
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Default Value
Partition 0 Name
Partition 1 Name
PART0
PART1
8
EN






EKB2 EKB3


Configurable by:
SMS
EKB2 EKB3









Configurable by:
SMS




Partitions
Parameter




System Notifications
Parameter


Configurable by:
SMS
Peripheral Devices
Parameter

Configuration
Tool

EKB2 EKB3



























Configurable by:
SMS
EKB2 EKB3




Configuration
Tool


Configuration
Tool



Configuration
Tool














Configuration
Tool


MANUAL ELDES ESIM264 V3.1
Partitions
Parameter
Default Value
Keypad 1... 4 Partition
Keypad Partition Switch
User Password 1... 30 Partition
User 1... 5 Phone Number Partition
iButton 1... 5 Partition
Zone Partition
PART0
Disabled
PART0
PART0
PART0
PART0
SMS
Default Value
MS Mode
Data Messages
Account (Alarm System ID)
Monitoring Station Phone Number 1... 3
(Voice Calls/SMS)
Attempts (Voice Calls/SMS)
Monitoring Station Phone Number 1...
5 (CSD)
Attempts (CSD)
Server IP Address (GPRS)
DNS1 Server IP Address (GPRS)
DNS2 Server IP Address (GPRS)
Protocol (GPRS)
Server Port (GPRS)
Local Port (GPRS)
APN (GPRS)
User (GPRS)
Password (GPRS)
Profile (GPRS)
GPRS Attempts
Delay Between Attempts (GPRS)
Unit ID (GPRS)
Test Period (GPRS)
Communication - Primary
Communication - Backup 1... 4
Protocol over GPRS
Disabled
All Enabled
9999
MANUAL ELDES ESIM264 V3.1
EKB2 EKB3






Monitoring Station
Parameter
Configurable by:






Configurable by:
Configuration
Tool






SMS
EKB2 EKB3







Configuration
Tool



N/A



3



N/A



3
0.0.0.0
N/A
N/A
UDP
20000
N/A
N/A
N/A
N/A
Profile1
3
600 seconds
0000
180 seconds
N/A
N/A
EGR100






















































EN
9
Additional Parameters
Parameter
Default Value
Event Log
Microphone Gain
Speaker Level
GSM Signal Loss Indication - Delay
GSM Signal Loss Indication - Activate
Output
Show ARMED Status in Keypad (EKB2)
Enabled
12
85
180 seconds


ELDES Smart Security
Server Address
Port
Disabled
ss.eldes.lt
8082
180 seconds
0
EN

Configuration
Tool




N/A
Default Value
10
EKB2 EKB3
Disabled
Parameter
Time Zone
SMS



ELDES Smart Security
Ping Period
Configurable by:
Configurable by:
SMS
EKB2 EKB3
Configuration
Tool





MANUAL ELDES ESIM264 V3.1
MANUAL ELDES ESIM264 V3.1
EN
11
2.TECHNICAL SPECIFICATIONS
2.1. Electrical & Mechanical Characteristics
Electrical & Mechanical Characteristics
Main power supply
Current in standby without external sensors and keypad
Recommended backup battery voltage, capacity
Recommended backup battery type
Maximum battery charge current
Gsm modem frequency
Cable type for GSM/GPRS antenna connection
Number of zones on-board
Nominal zone resistance
Number of PGM outputs on-board
On-board PGM output circuit
16-24V 50 Hz ~1.5A max / 18-24V
Up to 80mA
12V; 1,3-7 Ah
Lead-Acid
900mA
850/900/1800/1900MHz
Shielded
6 (ATZ mode: 12)
5,6kΩ (ATZ Mode: 5,6kΩ and 3,3kΩ)
4
Maximum commuting on-board PGM output values
BELL: Siren output when activated
BELL: Maximum cable length for siren connection
BELL: Cable type for siren connection
AUX: Auxiliary equipment power supply voltage
BELL+AUX: Maximum accumulative current of auxiliary equipment & siren
AUX: Maximum cable length for auxiliary equipment connection
AUX: Cable type for auxiliary equipment connection
BUZ: Maximum current of mini buzzer
BUZ: Power supply voltage of buzzer
BUZ: Cable type for mini buzzer connection
Supported temperature sensor model
Maximum supported number of temperature sensors
DATA: Maximum cable length for 1-Wire communication
DATA: Cable type for 1-Wire communication
Supported ibutton key model
Maximum supported number of iButton keys
Maximum supported number of keypads
Y/G: Maximum cable length for RS485 communication
Y/G: Cable type for RS485 communication
MIC: Maximum cable length for microphone connection
MIC: Cable type for microphone connection
Wireless transmitter-receiver frequency
Wireless communication range
Maximum supported number of wireless devices
Event log size
Maximum supported number of zones
Maximum supported number of pgm outputs
Cable type for zone and pgm output connection
Communications
Supported protocols
Dimensions
Operating temperature range
Humidity
4 x Voltage – 30V; current – 500mA.
Connected to COM
Up to 100 meters
Unshielded
13,8V DC
1A
Up to 100 meters
Unshielded
150mA
5V DC
Unshielded
Maxim®/Dallas® DS18S20, DS18B20
1
Up to 30 meters
Unshielded
Maxim®/Dallas® DS1990A
5
4 x EKB2 / EKB3
Up to 100 meters
Unshielded
Up to 2 meters
Unshielded
868 Mhz
Up to 30m in premises; up to 150m in open areas
16
500 events
44
44
Unshielded
SMS, Voice calls, GPRS network, RS485, CSD
Ademco Contact ID, EGR100, Kronos, Cortex SMS
140x100x18mm
-20...+55 °C
0-90% RH @ 0... +40 °C (non-condensing)
12
EN
1R
OUT
1,5A max
Open Collector Output.
Output is pulled to COM
when turned ON.
MANUAL ELDES ESIM264 V3.1
2.2. Main Unit, LED & Connector Functionality
DEF
OPEN
SIM CARD
G SM
MO DE M
3A
Slots for EA1, EA2 or EPGM8 module
Slots for EWT1 wireless module
C4
C3
1
ANTENNA
SMA
PRG
EWT1
USB
FUSE
MODULES*
EWT1
STATUS
PWR
Z6
Z5
Z4
Z3
Z2
Z1
C1
C2
NETWORK
Main Unit Functionality
GSM MODEM
GSM network 850/900/1800/1900MHz
modem
SIM CARD
SIM card slot / holder
DEF
Pins for restoring default settings
USB
Mini USB port
FUSE F1
3A fuse
GSM/GPRS antenna SMA type connector
ANTENNA
MODULES
AK U +
AK U -
AC /DC
AC /DC
AUX+
AUXBELL+
BELL-
CO M
G
Y
C2
C1
BU Z +
BU Z MIC +
M IC +5V
DAT A
CO M
Z6
CO M
Z5
Z4
CO M
Z3
Z2
CO M
Z1
LED Functionality
NETW indication
GSM signal strength
NETWORK
GSM network signal strength
OFF
No GSM signal
C2, C1
PGM output C1, C2 status – on/off
Flashing every 3 sec.
Poor
Z1
Zone Z1 state – alarm/restore (ATZ mode: Z1 and Z7)
Flashing every 1 sec.
Medium
Z2
Zone Z2 state – alarm/restore (ATZ mode: Z2 and Z8)
Flashing several times per sec.
Good
Z3
Zone Z3 state – alarm/restore (ATZ mode: Z3 and Z9)
Steady ON
Excellent
Z4
Zone Z4 state – alarm/restore (ATZ mode: Z4 and Z10)
Z5
Zone Z5 state – alarm/restore (ATZ mode: Z5 and Z11)
Z6
Zone Z6 state – alarm/restore (ATZ mode: Z6 and Z12)
PWR
Power supply status
STATUS
Micro-controller status
Connector Functionality
Z1 - Z6
Security zones
COM
Common terminal for all zones
DATA
1-Wire® interface for iButton® key & temperature sensor connection
+5V
Temperature sensor power supply contact (+5V)
MIC-
Microphone negative terminal
MIC+
Microphone positive terminal
BUZ-
Mini buzzer negative terminal
BUZ+
Mini buzzer positive terminal
C1 - C4
PGM outputs
Y
RS485 interface CLOCK terminal (yellow wire)
G
RS485 interface DATA terminal (green wire)
COM
Common return terminal
BELL-
Siren negative terminal
BELL+
Siren positive terminal
AUX-
Negative power supply terminal for auxiliary equipment
AUX+
Positive power supply terminal for auxiliary equipment
AC/DC
Main power supply terminal
AKU-
Backup battery negative terminal
AKU+
Backup battery positive terminal
MANUAL ELDES ESIM264 V3.1
EN
13
2.3. Wiring Diagrams
2.3.1.General Wiring
2
AKU+
AKU-
Backup Battery
12V 1.3-7Ah
AC /DC
AC /DC
AUX+
AUXBELL+
BELLCO M
G
Y
C2
C1
BUZ+
BUZMIC +
MIC +5V
DATA
CO M
Z6
CO M
Z5
Z4
CO M
Z3
Z2
CO M
Z1
Metal cabinet
PE terminal
Fuse 500 mA
~16-24V
~230V 50Hz
Z6
Z5
Z4
Z3
Z2
Z1
BUZ
5,6 kΩ
5,6 kΩ
5,6 kΩ
5,6 kΩ
5,6 kΩ
5,6 kΩ
MIC
SIREN/BELL
EPGM1
500mA max.
iButton®
key reader
Relay
module
EKB3
Temperature sensor
EKB2
2.3.2. Zone Connection Types
Type 1 Example of 4-wire smoke detector wiring
AUX+
C1
COM
Z1
3
5,6 kΩ
6-Zone mode: Normally open contact
with 5,6KΩ end-ofline resistor.
COM
GND
NO
+Vin
Type 2
6-Zone mode: Normally closed contact
with 5,6KΩ end-ofline resistor
5,6 kΩ
COM
Z1
4
Example of magnetic door contact wiring
COM
NC
Magnet
NOTE: Based on the example given, in the event of an alarm, the smoke detector could be reset by turining OFF and ON the PGM
output C1. For more details, please refer to 18.4. Turning PGM Outputs ON and OFF.
NOTE: The system does NOT support 2-wire smoke detectors.
14
EN
MANUAL ELDES ESIM264 V3.1
Type 3
Example of motion detector wiring
AUX+
AUX-
COM
Z1
5
6-Zone mode: Tamper
and 5,6KΩ end-of-line
resistor and 3,3KΩ
end-of-line resistor
with normally closed
contact.
COM
5,6 kΩ
3,3 kΩ
GND
NC
+Vin
TAMP
Example of magnetic door contact (Z1) and glass break sensor (Z7) wiring
AUX+
AUX-
5,6 kΩ
COM
Z1
6
ATZ mode: 5,6KΩ
end-of-line resistor
and normally closed
contact with 3,3KΩ
end-of-line resistor
and normally closed
contact
3,3 kΩ
Type 4
NC
COM
Magnet
Type 5
COM
GND
NC
+Vin
Example of motion detector (Z1) and magnetic door contact (Z7) wiring
AUX+
AUX-
ATZ mode: Tamper,
5,6KΩ end-of-line
resistor, 5,6KΩ
end-of-line resistor
with normally closed
contact and 3,3KΩ
end-of-line resistor
with normally closed
contact.
COM
Z1
7
5,6 kΩ
5,6 kΩ
3,3 kΩ
NC
COM
Magnet
COM
NC
TAMP
GND
+Vin
See also 14.3. 6-Zone Mode and 14.4. ATZ (Advanced Technology Zone) Mode.
MANUAL ELDES ESIM264 V3.1
EN
15
2.3.3. Siren
BELL+
BELL-
8
RED +
BELL+
BELLCOM
9
Self-contained siren
1 Connect negative GND siren wire to COM terminal.
2Controlling BELL siren wire must be connected
to BELL- terminal.
GND
SIREN/BELL
1A max.
1 Connect positive siren wire (red) to BELL+ terminal.
2 Connect negative siren wire (black) to BELLterminal.
BLACK SIREN/BELL
1A max.
Piezo siren
BELL
3 Connect positive +12V siren wire to BELL+ terminal.
+12V
See also 20. SIREN/BELL.
NOTE: BELL- is the commuted terminal intended for siren control.
16
EN
MANUAL ELDES ESIM264 V3.1
2.3.4. iButton Key Reader and Buzzer
Supported iButton key model: Maxim/Dallas
DS1990A
BUZ+
BUZ-
COM
DATA
10
-
The iButton key reader can be installed with buzzer
or separately. The buzzer is intended for audio indication of exit/entry delay countdown providing
short beeps.
+ BUZZER
1 Connect iButton key reader terminal wires to
1-Wire interface: COM and DATA terminals respectively.
2 Connect buzzer‘s negative terminal wire to BUZand positive terminal wire to BUZ+.
3 Additionally, a LED indicator for visual indication
can be installed in parallel to buzzer or instead.
Connect LED anode terminal to BUZ- and cathode to BUZ+.
iButton
key reader
DS1990A
NOTE: The installation of buzzer is not necessary if EKB2/EKB3 keypad is used.
ATENTION: The cable length for connection to 1-Wire interface can be up to 30 meters max.
2.3.5. Temperature Sensor and iButton Key Reader
Supported iButton key model: Maxim/Dallas DS1990A
Supported temperature sensor model: Maxim/Dallas DS18S20, DS18B20
TEMPERATURE
SENSOR
DS18S20,
DS18B20
DATA
GND
+5V
DS18S20, DS18B20
TEMPERATURE SENSOR
GND
1 Connect temperature sensor GND, DATA, +5V
terminals to 1-Wire interface: COM, DATA and
+5V terminals respectively.
2 When connecting iButton key reader in parallel
to temperature sensor, connect iButton key reader terminal wires to COM and DATA terminals
respectively.
+5V
DATA
COM
+5V
DATA
COM
11
ATENTION: The cable length for connection to
1-Wire interface can be up to 30 meters max.
GND
+5V
DATA
DATA +5V
iButton
key reader
DS1990A
2.3.6. Relay Finder 40.61.9.12 with Terminal Socket 95.85.3 to PGM Output
AUX+
C1
12
1 Wire up relay A1 terminal to PGM output Cx and
A2 terminal to AUX+.
2 In addition, connect LED indicator‘s anode terminal to relay A2 terminal and cathode to A1
terminal.
LED
COIL
A2
A1
RELAY
MANUAL ELDES ESIM264 V3.1
EN
17
2.3.7. RS485
Serial Wiring Method
ESIM264
a
EKB2/EKB3
b
EKB2/EKB3
c
EKB2/EKB3
d
EKB2/EKB3
e
EPGM1
Max. cable length: a+b+c+d+e = up to 100 meters
NOTE: If necessary, the RS485 devices can be powered from an external 12-14V DC power supply instead of AUX+ and AUX- terminals
ATTENTION: The cable length must not exceed 100 meters in total.
ATTENTION: When wiring more than 1 keypad, please ensure that the set address of each keypad is different.
NOTE: You may connect only 1 EKB2/EKB3 keypad or a mixed combination of EKB2 and EKB3 keypads. The combination can consist of
up to 4 keypads in total.
For more details on RS485 device installation, please refer to 32.1. RS485 Interface
18
EN
MANUAL ELDES ESIM264 V3.1
Parallel Wiring Method
ESIM264
Max. cable length: up to 100 meters
EPGM1
EKB2/EKB3
EKB2/EKB3
EKB2/EKB3
EKB2/EKB3
NOTE: If necessary, the RS485 devices can be powered from an external 12-14V DC power supply instead of AUX+ and AUX- terminals
ATTENTION: The cable between ESIM264 and each RS485 device must be of the same length and can NOT exceed 100 meters.
ATTENTION: When wiring more than 1 keypad, please ensure that the set address of each keypad is different.
NOTE: You may connect only 1 EKB2/EKB3 keypad or a mixed combination of EKB2 and EKB3 keypads. The combination can consist of
up to 4 keypads in total.
For more details on RS485 device installation, please refer to 32.1. RS485 Interface
MANUAL ELDES ESIM264 V3.1
EN
19
3.INSTALLATION
• The system can be installed in a metal or non-flammable cabinet only. For a convenient installation, ME1 metal cabinet is highly recommended. When using a different metal cabinet, it is necessary to ground it.
• For the connection of 230V transformer, use 3x0.75 mm2 1 thread double isolated cable. 230V power supply cables must not be
grouped with low voltage cable group.
• For the connection of auxiliary and BELL outputs, use 2x0.75 mm2 1 thread unshielded cable of up to 100 meters length.
• For the connection of zone/PGM output connectors, use 0.50 mm2 1 thread unshielded cable of up to 100 meters length.
System Installation in ME1 Metal Cabinet
1. ME1 metal cabinet components
13
to AC main power line
Null
blue
PE
Phase
brown
Fuse 1A
Transformer
(Primary voltage: 230V AC,
Secondary voltage: 17V
2,35A)
Tamper switch
to AC/DC terminals
of ESIM264 system
2. Insert the plastic standoffs into the appropriate mounting points and fix the board of ESIM264 on the holders as indicated below.
14
mounting points
20
EN
MANUAL ELDES ESIM264 V3.1
15
7
3. If EPGM1 module is to be installed, please install it in the first place and ESIM264 alarm system afterwards. EPGM1 must be mounted on
the shorter plastic standoffs, while ESIM264 – on the longer ones. The mounting points of EPGM1 module are indicated below.
16
mounting
points
MANUAL ELDES ESIM264 V3.1
EN
21
17
18
7
4. Wire up the system according to the wiring diagrams. Install the buzzer closer to iButton key reader in order to hear the exit delay
countdown. A LED indicator can be used in parallel to the buzzer or instead. For a convenient installation, ED1 is highly recommended
(see 2.3 Wiring Diagrams for more details).
5. Disable the PIN code of the SIM card by inserting it into a mobile phone and following the proper menu steps. Ensure that the addition
al services, such as voice mail, call forwarding, report on missed/busy calls are disabled on the SIM card. For more details on
how to disable these services, please contact your GSM operator.
6. Once the PIN code is disabled, place the SIM card into the SIM CARD slot of the alarm system.
29
21
OPEN
20
22
EN
MANUAL ELDES ESIM264 V3.1
23
OPEN
22
7. Connect the GSM/GPRS and wireless antennas and follow the recommendations for the installation:
Never install in the following
locations:
24
GSM/
GPRS
and/or
wireless
antenna
Recommended installation:
25
20 cm
or more
• inside the metal cabinet
• closer than 20 cm from the
metal surface and/or power
lines
GSM/GPRS
antenna
• keep the distance of at least 20
cm or more.
Wireless
antenna
8. If one or more wireless devices are to be bound, follow the recommendations for the installation to achieve the strongest wireless
signal:
Never install in the following
locations:
26
0.5 m to 30 m
inside the building
• inside the metal cabinet
Wireless
device
• closer than 20 cm from the
metal surface and/or power
lines
Recommended installation:
27
0.5 m to 150 m
in open areas
Wireless
device
Wireless
antenna
• face the front side of the
wireless device towards the
antenna
• keep the distance: 0.5 m to 30
m inside the building, 0.5 m to
150 m in open areas
For more details on how to install the wireless devices, please refer to 32. ELDES WIRELESS DEVICES and RADIO SYSTEM INSTALLATION AND SIGNAL PENETRATION manual located at www.eldes.lt/download
9. Power up the system.
10. The system starts up in less than a minute. Indicator STATUS should be flashing indicating successful micro-controller operation.
11. The illuminated indicator NETWORK indicates that the system successfully registered to GSM network. To find the strongest GSM
signal, place the GSM/GPRS antenna and follow the indications provided by NETWORK indicator (see 2.3. Main Unit, LED & Connector Functi­onality).
12. Change the default SMS password (see 6. PASSWORDS for more details).
13. Set the phone number for User 1 (see 8. USER PHONE NUMBERS for more details).
14. Set system date and time (see 9. DATE AND TIME for more details).
15. Once the system is fully configured, it is ready for use. However, if you fail to receive an SMS reply from the system, please check the
SMSC (Short Message Service Center) phone number. For more details regarding the SMS centre phone number, please refer to 27.1.
SMSC (Short Message Service Center) Phone Number.
ATTENTION: The system is NOT compatible with pure 3G SIM cards. Only 2G/GSM SIM cards and 3G SIM cards with 2G/GSM profile enabled
are supported. For more details, please contact your GSM operator.
NOTE: The installation of iButton key reader, EKB2/EKB3 keypad, EWK1 wireless keyfob is not mandatory. However, it is recommended to
have those devices installed as an emergency switch in case your mobile phone is switched off or missing.
NOTE: For maximum system reliability we recommend you do NOT use a Pay As You Go SIM card. Otherwise, in the event of insufficient
credit balance on the SIM card, the system would fail to make a phone call or send messages.
MANUAL ELDES ESIM264 V3.1
EN
23
NOTE: We advise you to choose the same GSM SIM provider for your system as for your mobile phone. This will ensure the fastest,
most reliable SMS text message delivery service and phone call connection.
NOTE: Even though alarm system ESIM264 installation process is not too complicated, we still recommend to perform it by a person
with basic knowledge in electrical engineering and electronics to avoid any system damage.
4.GENERAL OPERATIONAL DESCRIPTION
When the system is being armed, it will initiate the exit delay countdown intended for the user to leave the secured area. During the countdown period the buzzer will emit short beeps and/or LED indicator will flash. By default, exit delay duration is 15 seconds. After the countdown is complete, the system will become armed and lock the configuration by keypad possibility. In case the user does not leave the secured area before the countdown is complete, the system will will arm in Stay mode if at least 1 zone has Stay attribute enabled. By default,
if there is at least 1 violated zone or tamper, the user will not be able to arm the system until the violated zone or tamper is restored. In case
it is required to arm the alarm system despite the violated zone presence, the violated zone can be bypassed or Force attribute enabled.
After the system is armed and if a zone (depending on type) or tamper is violated, the system will cause an alarm lasting for 1 minute (by
default), During the alarm, the siren/bell will provide an alarm sound along with the buzzers of the keypads. By default, the system will also
makes a phone call and send an SMS text message containing the violated zone or tamper number to a preset user and indicate the violated
zone or tamper number on the keypad. If another zone or tamper is violated or the same one is restored and violated again during the alarm,
the system will act as mentioned previously, but will not extend the alarm time.
After the user enters the secured area, the system will initiate the entry delay countdown intended for system disarming. During the countdown period, the buzzer will emit a steady beep and/or LED indicator will light ON. By default, entry delay duration is 15 seconds. After the
user successfully performs the disarming process, the system will unlock the keypads. If the user does not disarm the system in time, the
alarm system will cause an instant alarm.
NOTE: The alarm will be caused even if a tamper is violated while the system is disarmed.
For more details, please refer to 12. ARMING AND DISARMING.
24
EN
MANUAL ELDES ESIM264 V3.1
5.CONFIGURATION METHODS
!!! In this installation manual the underscore character ”_” represents one space character. Every underscore character
must be replaced by a single space character. There must be no spaces or other unnecessary characters at the beginning
and at the end of the SMS text message.
SMS
EKB2
In order to configure and control the system by SMS text message, send the text command to the ESIM264 system phone
number from one of the preset user phone numbers. The structure of SMS text message consists of 4-digit SMS password
(the default SMS password is 0000 – four zeros), the parameter and value. For some parameters the value does not apply e. g.
STATUS. The variables are indicated in lower-case letters, while a valid parameter value range is indicated in brackets.
The system configuration and control by EKB2 keypad is carried out by navigating throughout the menu section list displayed
on LCD screen. To navigate in the menu path, touch ↓, ↑ keys to select the desired menu section and touch OK key to open the
selected section. To enter a required value, use 0... 9 keys and touch OK key for confirmation or cancel/go one menu section
back by touching ← key. The value can be typed in directly by touching 0... 9 keys while highlighting the desired menu section. EKB2 menu type is “circle”, therefore when the last section in the menu list is selected, you will be brought back to the
beginning of the list after touching the ↓ key. In this installation manual, the menu path is based on the EKB2 menu tree by
starting at home screen view (see 31.1.1.6. EKB2 Menu Tree ). The variables are provided in lower-case letters, while a valid
parameter value range is provided in brackets.
NOTE: Menu section CONFIGURATION is secured with administrator password. The default administrator password is 1470.
NOTE: The system can be configured using only one keypad at a time. Other connected keypads will be inactive while the menu section
CONFIGURATION is opened. The inactive EKB2 keypads will display
icon and CONFIGURATION MODE message.
NOTE: The keypad will automatically exit the menu section CONFIGURATION and return to home screen view if 1 minute after the last
key-touch expires.
EKB3
The system configuration and control by EKB3 keypad is carried out by activating the Configuration mode using the administrator password (by default – administrator password is 1470) and entering a valid configuration command using the number
keys [0]... [9], [#] key for confirmation and [*] key to cancel the characters that are being entered. Alternatively, the user
can wait for 10 seconds until the keypad buzzer will provide a long beep indicating that the entered characters have been
cancelled. When typing in the characters, the indication of each pressed key is provided by short beep of keypad buzzer and
red indicators when the number keys [0]... [9] are being pressed. Some commands require [BYPS], [CODE] and [STAY] keys as
well. The structure of a standard configuration command is a combination of digits. The commands, which do not require the
Configuration mode being activated, are noted. The variables are provided in lower-case letters, while a valid parameter value
range is provided in brackets.
NOTE: If you were not willing to activate Configuration mode, but accidentally typed in the * as the first character, please press [*] key again
or wait for 10 seconds until the keypad buzzer will provide a long beep indicating that the typed in characters have been cancelled.
Activate/deactivate
Configuration mode
MANUAL ELDES ESIM264 V3.1
EKB3
Enter administrator password:
* aaaa #
Value: aaaa – 4-digit administrator password.
Example: *1470#
EN
25
The following table provides a list of EKB3 indications, which are relevant during Configuration mode.
Indication
Indicator ARMED flashing
Indicator SYSTEM flashing
1 long beep
3 short beeps
Description
Configuration mode activated successfully.
Valid parameter is entered and waiting for valid value to be enetered.
Non-existing command or invalid parameter value entered.
Command entered successfully.
NOTE: The system can be configured using only one keypad at a time. Other connected keypads will be inactive while the Configuration mode is activated.
NOTE: Configuration mode will automatically deactivate if 1 minute after the last key-stroke expires.
Config
Tool
Software ELDES Configuration Tool is intended for ESIM264 alarm system configuration via USB port locally or via GPRS connection remotely. This software simplifies system configuration process by allowing to use a personal computer in the process.
Before starting to use ELDES Configuration Tool software, please read the user guide provided in the software’s HELP section.
ELDES Configuration Tool is freeware and can be downloaded from at: www.eldes.lt
Remote System Configuration via GPRS Connection
ATTENTION: The system will NOT send any data to monitoring station while configuring the system remotely via GPRS network. However,
during the configuration session, the data messages are queued up and transmitted to the monitoring station after the configuration
session is over.
ATTENTION: When the Configuration mode is activated by EKB3 keypad or menu section CONFIGURATION is opened by EKB2 keypad,
remote system configuration will be disabled.
NOTE: The keypads will be inactive when the system is being configured remotely.
Before configuring ESIM264 remotely via GPRS connection, make sure that:
• SIM card is inserted into SIM CARD1 slot of ESIM264 device (see 2.2. Main Unit, LED & Connector Functionality).
• Mobile internet service (GPRS) is enabled on the SIM card.
• Power supply is connected to ESIM264.
• Default SMS password is changed to a new 4-digit password (see 6. PASSWORDS).
• At least User 1 phone number is set up (see 8. USER PHONE NUMBERS).
• APN, user name and password are set up (see 30.2.1. GPRS Network).
Establishing Remote Connection Between ESIM264 System and Configuration Server
Initiate the
connection
to ELDES server
In order to activate a remote GPRS connection between ESIM264 system and ELDES configuration
server please , send the following SMS text message from user phone number.
Upon the successful SMS text message delivery, the system establishes a connection session for
20 minutes. An SMS reply, containing device IMEI number and confirming a successful connection
establishment, is sent shortly.
SMS
26
EN
SMS text message content:
ssss_STCONFIG
Value: ssss – 4-digit new SMS password.
Example: 1111_STCONFIG
MANUAL ELDES ESIM264 V3.1
Initiate the
connection to
third-party server
In case it is necessary to establish a connection between ESIM264 system and a third-party
configuration server, send the following SMS text message.
SMS
SMS text message content:
ssss_STCONFIG:add.add.add.add:Port or ssss_STCONFIG:host-name:pprrt
Value: ssss – 4-digit SMS password; add.add.add.add – public IP address of third-party configuration server; pprrt – port number of third-party configuration server, range – [1... 65535]; host-name – public host-name of third-party configuration server.
Example: 1111_STCONFIG:62.80.115.102:4522
NOTE: Public IP address (host-name) and port number are necessary when connecting to a third-party-server for the first time only.
When connecting to the server next time, ssss_STCONFIG is enough as the IP address (host-name) and port number are saved in the
device memory after the first successful connection.
Connecting to ELDES Configuration Server using ELDES Configuration Tool Software
•
Run ELDES Configuration Tool software.
•
Press Remote Configuration button.
•
In the next window, select Connect to Remote Server (recommended) and press Next button.
•
Enter the received IMEI number in Device IMEI entry.
•
Press Continue button.
•
Upon the successfully established connection, the system prompts for an administrator password.
•
By entering a valid administrator password, the sys­tem grants access to full configuration remotely.
•
Remote Configuration Management window displays all performed configuration actions.
28
Ending the Configuration Process
Shut down the
Connection with the
Server
After the system configuration is complete, use one of the following methods to end the configuration
process:
• Press Disconnect button and close ELDES Configuration Tool software;
• Wait for the system to reply with an SMS text message confirming the end of the session;
• Shut down the connection with the server at any time by sending an SMS text message.
SMS
MANUAL ELDES ESIM264 V3.1
SMS text message content:
ssss_ENDCONFIG
Value: ssss – 4-digit SMS password.
Example: 1111_ENDCONFIG
EN
27
6.PASSWORDS
For security reasons, the system uses the following types of passwords:
•
SMS password – 4-digit password used for system arming/disarming and configuration by SMS text messages. By default, SMS password is 0000, which MUST be changed!
•
Administrator password – 4-digit password used for Configuration mode activation by keypad and logging in to ELDES Configuration
Tool software. By default, Administrator password is 1470, which is highly recommended to change.
Set SMS password
SMS
EKB2
Set Administrator
password
Enter parameter 14 & new SMS password:
14 ssss #
Value: ssss – 4-digit new SMS password; range – [0001... 9999].
Example: 141111#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EKB2
Menu path:
OK → CONFIGURATION → OK → 1470 → OK → PRIMARY SETTINGS → OK → PASSWORDS
→ OK → ADMIN PASSWORD → OK → aaaa → OK
Value: aaaa – 4-digit new administrator password; range – [0000... 9999].
Config
Tool
EN
Menu path:
OK → CONFIGURATION → OK → aaaa → OK → PRIMARY SETTINGS → OK → PASSWORDS
→ OK → SMS PASSWORD → OK → ssss → OK
Value: aaaa – 4-digit administrator password; ssss – 4-digit new SMS password; range –
[0001... 9999].
EKB3
EKB3
28
SMS text message content:
wwww_PSW_ssss
Value: wwww – 4-digit default SMS password; ssss – 4-digit new SMS password; range –
[0001... 9999].
Example: 0000_PSW_1111
Enter parameter 16 & new administrator password:
16 aaaa #
Value: aaaa – 4-digit new administrator password; range – [0000... 9999].
Example: 162538#
This operation may be carried out from the PC using the ELDES Configuration Tool software.
MANUAL ELDES ESIM264 V3.1
7.SYSTEM LANGUAGE
The system comes equipped with 2 languages for communication with the user by SMS text messages and a single language for EKB2
keypad menu display. The default EKB2 menu language depends on ESIM264 firmware, which is based on the user’s location, while one of
languages for communication by SMS text messages is always English.
List of currently available system languages (firmwares):
• Czech
• English
• Estonian
• Finnish
• French
• Greek
• Hungarian
• Icelandic
• Italian
• Latvian
• Lithuanian
• Norwegian
• Portuguese
• Romanian
• Russian
• Slovak
• Spanish
• Swedish
To set a different SMS language, please refer to the following configuration methods.
Set SMS language
SMS
EKB2
SMS text message content:
ll
Value: ll - SMS language, range - [CZ - Czech, EN - English, EE - Estonian, FI - Finnish, GR - Greek, HU - Hungarian, IC - Icelandic, IT - Italian, LV - Latvian, LT - Lithuanian, NO - Norwegian, PT
- Portuguese, RO - Romanian, RU - Russian, SK - Slovak, SP - Spanish, SW - Swedish].
Example: SK
Menu path:
OK → CONFIGURATION → OK → 1470 → OK → PRIMARY SETTINGS → OK → SMS LANGUAGE
→ OK → sms-lang → OK
Value: aaaa – 4-digit new administrator password; range – [0000... 9999]; sms-lang – SMS
language.
NOTE: To obtain a firmware that features a different SMS and EKB2 menu language, please contact your local dealer.
NOTE: To change the language once the system has already been configured, you need to reset the device to the default configuration. For
more details on how to do this, please refer to 35.2. Restoring Default Parameters.
MANUAL ELDES ESIM264 V3.1
EN
29
8.USER PHONE NUMBERS
The system supports up to 5 user phone numbers identified as User 1 through 5. When the phone number is set, the user will be able to
arm/disarm the system by SMS text messages and free of charge phone calls (see 12.1. Free of Charge Phone Call and 12.2. SMS Text
Message) as well as to configure the system by SMS text messages. User phone numbers are also used to receive alarm phone calls and
SMS text messages from the system (see 17. ALARM INDICATIONS AND NOTIFICATIONS).
By default, the system ignores any incoming calls and SMS text messages from a non-preset phone number as well as it rejects the SMS text
messages containing wrong SMS password even from a preset user phone number (see 8.2. System Control from any Phone Number).
To set User 1 phone number is mandatory, while the other 4 are optional. The supported phone number format is the following:
•
International (w/o plus) – The phone numbers must be entered starting with an international country code in the following format: [international code][area code][local number], example for UK: 4417091111111.
Set user phone
number
SMS
EKB2
EKB3
Config
Tool
View user phone
number
30
EN
SMS text message content:
ssss_NRup:ttteeellnnuumm
Value: ssss – 4-digit SMS password; up – user phone number slot, range – [1... 5]; ttteeelln­
nuumm – up to 15 digits user phone number.
Example: 1111_NR1:4417091111111
Menu path:
OK → CONFIGURATION → OK → aaaa → OK → PRIMARY SETTINGS → OK → CALL/SMS SETTINGS
→ OK → USERS → OK → USER 1... 5 → OK → PHONE NUMBER → OK → ttteeellnnuumm → OK
Value: aaaa – 4-digit administrator password; ttteeellnnuumm – up to 15 digits user phone
number.
Enter parameter 17, user phone number slot & phone number:
17 up ttteeellnnuumm #
Value: up – user phone number slot, range – [01... 05]; ttteeellnnuumm – up to 15 digits user
phone number.
Example: 17014417091111111#
This operation may be carried out from the PC using the ELDES Configuration Tool software.
SMS
SMS text message content:
ssss_HELPNR
Value: ssss – 4-digit SMS password.
Example: 1111_HELPNR
EKB2
Menu path:
OK → CONFIGURATION → OK → aaaa → OK → PRIMARY SETTINGS → OK → CALL/SMS
SETTINGS → OK → USERS → OK → USER 1... 5 → OK → PHONE NUMBER → PHONE NUMBER
Value: aaaa – 4-digit administrator password.
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
MANUAL ELDES ESIM264 V3.1
Delete user phone
number
SMS
SMS text message content:
ssss_NRup:DEL
Value: ssss – 4-digit SMS password; up – user phone number slot, range – [2... 5].
Example: 1111_NR2:DEL
EKB2
Menu path:
OK → CONFIGURATION → OK → aaaa → OK → PRIMARY SETTINGS → OK → CALL/SMS
SETTINGS → OK → USERS → OK → USER 2... 5 → OK → PHONE NUMBER → OK → OK
Value: aaaa – 4-digit administrator password.
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
ATTENTION: NEVER add a phone number of the device’s SIM card as a user phone number!
ATTENTION: Once User 1 phone number is set, it will be restricted to modify it only.
NOTE: Multiple user phone numbers can be set by a single SMS text message, Example: 1111_NR1:4417091111111_ NR2:4417091111112_
NR5:4417091111113
NOTE: Multiple user phone numbers can be deleted by a single SMS text message, Example: 1111_NR2:DEL_NR3:DEL
8.1. System Control from any Phone Number
By default, the system ignores any incoming calls and SMS text messages from a non-preset phone number as well as it rejects the SMS
text messages containing wrong SMS password even from a preset user phone number. To allow/disallow system arming/disarming by
phone call and SMS text messages that contain a valid SMS password from any phone number, please refer to the following configuration
methods.
Enable system control
from any phone
number
SMS
SMS text message content:
ssss_STR:ON
Value: ssss – 4-digit SMS password.
Example: 1111_STR:ON
EKB2
Menu path:
OK → CONFIGURATION → OK → aaaa → OK → PRIMARY SETTINGS → OK → CALL/SMS
SETTINGS → OK → CTRL FROM ANY NUM → OK → ENABLE → OK
Value: aaaa – 4-digit administrator password.
MANUAL ELDES ESIM264 V3.1
EKB3
Enter parameter 12 & parameter status value:
12 1 #
Example: 121#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EN
31
Disable system
control from any
phone number
32
EN
SMS
SMS text message content:
ssss_STR:OFF
Value: ssss – 4-digit SMS password.
Example: 1111_STR:OFF
EKB2
Menu path:
OK → CONFIGURATION → OK → aaaa → OK → PRIMARY SETTINGS → OK → CALL/SMS
SETTINGS → OK → CTRL FROM ANY NUM → OK → DISABLE → OK
Value: aaaa – 4-digit administrator password.
EKB3
Enter parameter 12 & parameter status value:
12 0 #
Example: 120#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
MANUAL ELDES ESIM264 V3.1
9.DATE AND TIME
The system comes equipped with internal real-time clock (RTC) that keeps track of the current date and time. Once the system is up and
running, the user must set the correct date and time, otherwise the system will not operate properly. After shutting down and starting up
the system, the date and time must be set again.
Set date and time
SMS
EKB2
EKB3
Config
Tool
SMS text message content:
ssss_yyyy.mm.dd_hr:mn
Value: ssss – 4-digit SMS password; yyyy – year; mm – month, range – [01... 12]; dd – day,
range – [01... 31]; hr – hours, range – [00... 23]; mn – minutes, range – [00... 59].
Example: 1111_2013.03.16_14:33
Menu path:
a) OK → DATE/TIME SETTINGS → OK →yyyy-mm-dd hr:mn → OK
b) OK → CONFIGURATION → OK → aaaa → OK → PRIMARY SETTINGS → OK → DATE/TIME
SETTINGS → OK → yyyy-mm-dd hr:mn → OK
Value: aaaa – 4-digit administrator password; yyyy – year; mm – month, range – [01... 12];
dd – day, range – [01... 31]; hr – hours, range – [00... 23]; mn – minutes, range – [00... 59].
Enter parameter 66, date & time:
66 yyyy mm dd hr mn#
Value: yyyy – year; mm – month, range – [01... 12]; dd – day, range – [01... 31]; hr – hours,
range – [00... 23]; mn – minutes, range – [00... 59].
Example: 66201305291235#
This operation may be carried out from the PC using the ELDES Configuration Tool software.
NOTE: When the system is connected to the monitoring station via GPRS network connection (see 30. MONITORING STATION) and/or
when ELDES Smart Security feature is in use (see 35. ELDES Smart Security), the date and time will be automatically synchronized with
the monitoring station or ELDES Smart Security server upon the system startup.
MANUAL ELDES ESIM264 V3.1
EN
33
10.USER PASSWORDS
The system supports up to 30 numeric user passwords, identified as User Password 1 through 30, allowing to carry out system arming/disarming by the keypad. By default, User Password 1 is preset as 1111 and assigned to Partition 1. For more details regarding user password
partition, please refer to 23.4. User Password Partition.
Set user password
EKB2
EKB3
Delete user password
Replace user
password
Menu path:
User password 1... 16: OK → CONFIGURATION → OK → aaaa → OK → PRIMARY SETTINGS →
OK → PASSWORDS → OK → USER PASSWORDS → OK → USER PSW (1-16) → OK → USER
PASSWORD 1... 16 → OK → PASSWORDS → OK → uuuu → OK
User password 17... 30: OK → CONFIGURATION → OK → aaaa → OK → PRIMARY SETTINGS →
OK → PASSWORDS → OK → USER PASSWORDS → OK → USER PSW (17-30) → OK → USER
PASSWORD 17... 30 → OK → PASSWORDS → OK → uuuu → OK
Value: aaaa – 4-digit administrator password; uuuu – 4-digit user password, range – [0000...
9999].
Enter parameter 15, user password slot & user password:
15 us uuuu #
Value: us – user password slot, range – [01... 30]; uuuu – 4-digit user password; range –
[0000... 9999].
Example: 15021111#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EKB2
Menu path:
OK → CONFIGURATION → OK → aaaa → OK → PRIMARY SETTINGS → OK → PASSWORDS →
OK → USER PASSWORDS → OK → REMOVE PASSWORD → OK → uuuu → OK
Value: aaaa – 4-digit administrator password; uuuu – 4-digit user password.
EKB3
Enter parameter 65 & user password:
65 uuuu #
Value: uuuu – 4-digit user password.
Example: 651111#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EKB2
EKB3
Config
Tool
Menu path:
User password 1... 16: OK → CONFIGURATION → OK → aaaa → OK → PRIMARY SETTINGS →
OK → PASSWORDS → OK → USER PASSWORDS → OK → USER PSW (1-16) → OK → USER
PASSWORD 1... 16 → OK → PASSWORD → OK → uuuu → OK
User password 17... 30: OK → CONFIGURATION → OK → aaaa → OK → PRIMARY SETTINGS
→ OK → PASSWORDS → OK → USER PASSWORDS → OK → USER PSW (17-30) → OK → USER
PASSWORD 17... 30 → OK → PASSWORD → OK → uuuu → OK
Value: aaaa – 4-digit administrator password; uuuu – 4-digit user password, range –
[0000... 9999].
Enter parameter 63, existing user password & new user password:
63 vvvv uuuu #
Value: vvvv – 4-digit existing user password; uuuu – 4-digit new user password, range –
[0000... 9999].
Example: 6311113254#
This operation may be carried out from the PC using the ELDES Configuration Tool software.
NOTE: The system does not allow to set a duplicate password
34
EN
MANUAL ELDES ESIM264 V3.1
One of the user passwords ranging from User Password 1 through 10 can be set as SGS (Security Guard Service) password, which is used
for system arming/disarming by a security service employee. When used, the SGS password will be identified by a unique Contact ID code
in the monitoring station.
Set SGS password
EKB2
Menu path:
OK → CONFIGURATION → OK → aaaa → OK → PRIMARY SETTINGS → OK → PASSWORDS →
OK → USER PASSWORDS → OK → SGS PASSWORD → OK → N/A / us → OK
Value: aaaa – 4-digit administrator password; N/A – SGS password not in use; us – user password slot, range – [1... 10].
EKB3
Enter parameter 74 & user password slot:
74 us #
Value: us – user password slot, range – [01... 10].
Example: 7403#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
The Duress password is used when system disarming is demanded by force. When used, the system will disarm as well as it will silently
transmit an alert to the monitoring station. Only one of the user passwords ranging from User Password 1 through 10 can be set as Duress
password.
Set Duress password
MANUAL ELDES ESIM264 V3.1
EKB2
Menu path:
OK → CONFIGURATION → OK → aaaa → OK → PRIMARY SETTINGS → OK → PASSWORDS →
OK → USER PASSWORDS → OK → DURESS PASSWORD → OK → N/A / us → OK
Value: aaaa – 4-digit administrator password; N/A – Duress password not in use; us – user
password slot, range – [1... 10].
EKB3
Enter parameter 73 & user password slot:
73 us #
Value: us – user password slot, range – [01... 10].
Example: 7309#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EN
35
11.iBUTTON KEYS
An iButton key is a unique 64-bit ID code containing chip enclosed in a stainless steel tab usually implemented in a small plastic holder.
ESIM264 system supports up to 5 iButton keys each holding a unique identity code (ID), which is used for system arming and disarming.
11.1. Adding and Removing iButton Keys
To add an iButton key to the system, do the following:
a) Disarm the system in all partitions (see 12. ARMING AND DISARMING).
b) Enable Allow Adding New iButton Keys mode.
c) T ouch the key to the iButton key reader when the system is disarmed (see picture below).
29
d) The successfully added iButton key will be indicated by short beeps emitted by the system’s buzzer.
e) Add as many iButton keys as necessary – touch one key after another to the reader – until the number of 5 keys is reached.
NOTE: iButton Key 1 can be added without Allow Adding New iButton Keys mode being enabled.
Enable Allow Adding
New iButton Keys
mode
SMS
SMS text message content:
ssss_IBPROG:ON
Value: ssss – 4-digit SMS password.
Example: 1111_IBPROG:ON
EKB2
Menu path:
OK → CONFIGURATION → OK → aaaa → OK → IBUTTON KEYS → OK → NEW IBUTTON →
OK → ENABLE → OK
Value: aaaa – 4-digit administrator password.
EKB3
Enter parameter 18 & parameter status value:
18 0 #
Example: 180#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
When adding of iButton keys is complete, please disable Allow Adding New iButton Keys mode.
36
EN
MANUAL ELDES ESIM264 V3.1
Disable Allow Adding
New iButton Keys
mode
SMS
SMS text message content:
ssss_IBPROG:OFF
Value: ssss – 4-digit SMS password.
Example: 1111_IBPROG:ON
EKB2
Menu path:
OK → CONFIGURATION → OK → aaaa → OK → IBUTTON KEYS → OK → NEW IBUTTON →
OK → DISABLE → OK
Value: aaaa – 4-digit administrator password.
EKB3
Enter parameter 18 & parameter status value:
18 1 #
Example: 181#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
To view the ID of the added iButton keys, please refer to the following configuration methods.
View iButton key ID
EKB2
Menu path:
OK → CONFIGURATION → OK → aaaa → OK → IBUTTON KEYS → OK → IBUTTON 1... 5 → OK
→ ID
Value: aaaa – 4-digit administrator password.
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
If the iButton key is lost or stolen, due to security reasons it is highly recommended to remove it from the system.
Remove individual
iButton key from the
system
Remove all iButton
keys from the system
MANUAL ELDES ESIM264 V3.1
EKB2
Menu path:
OK → CONFIGURATION → OK → aaaa → OK → IBUTTON KEYS → OK → IBUTTON 1... 5 → OK
→ REMOVE → OK
Value: aaaa – 4-digit administrator password..
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
SMS
SMS text message content:
ssss_RESETIB
Value: ssss – 4-digit SMS password.
Example: 1111_RESETIB
EN
37
12.ARMING AND DISARMING
The system features the following methods to carry out arming and disarming process:
•
Free of charge phone call.
•
SMS text message.
•
EKB2/EKB3 keypad and user password.
•
iButton key.
•
EWK1/EWK2 wireless keyfob.
•
Arm-Disarm by Zone.
•
EGR100 middle-ware.
The system arms/disarms the partitions that the preset user phone number, EKB2/EKB3 keypad and user password, iButton key, EWK1 wireless keyfob or zone, set up for Arm-Disarm by Zone method, are assigned to. For example, if User 1 phone number is assigned to Partition 0,
the user will be able to arm/disarm Partition 0 by a single phone call to the system (see 23. PARTITIONS).
By default, when the system is successfully armed or disarmed, it replies with confirmation by SMS text message. For more details on SMS
text message regarding system arming/disarming and how to manage it, please refer to 12.9. Disabling and Enabling Arm/Disarm
Notifications.
The system will allow to arm the system if the following system faults are present (see 29. INDICATION OF SYSTEM FAULTS):
• Main power supply is lost.
• Low battery.
• Battery failed.
• Date/time not set.
• GSM connection failed.
When attempting to arm the system (by any method, except EKB2/EKB3 keypad and user password, EGR100 middle-ware) in case of violated zone/tamper presence, the system will reply with SMS text message containing violated zone/tamper number. Due to security reasons
it is highly recommended to restore the violated zone/tamper before arming the system. For more details on how to arm the sys­tem despite
the violated zone presence, please refer to 14.6. Zone Attributes and 14.7. Bypassing and Activating Zones
The system ignores any incoming calls and SMS text messages from a non-preset phone number as well as it rejects the SMS text messages
containing wrong SMS password even from a preset user phone number. For more details regarding arming/disarming the system from a
non-preset phone number, please refer to 8.1. System Control from any Phone Number.
12.1. Free of Charge Phone Call
To arm and disarm the system, dial the system‘s phone number from any of 5 available user phone numbers (see 8. USER
PHONE NUMBERS for user phone number management). The phone call is free charge as the system rejects it and carries out
arming/disarming procedure afterwards. When arming – the system rejects the phone call after 2 rings, when disarming – the
system rejects the phone call immediately. If there is more than one preset user dialing to the system at the same time, the
system will accept the incoming call from the user who was the first to dial while other user (-s) will be ignored.
When system’s phone number is dialed for arming, the system will proceed as follows:
•
•
Non-partitioned system:
•
If ready (no violated zone/tamper), the system will arm.
•
If unready (violated zone/tamper is present), the system will not arm and provide a list of violated zones/tampers by SMS text
message to user phone number.
Partitioned system:
•
If all partitions are disarmed ready, the system will arm them.
•
If one or more partitions are disarmed unready (violated zone/tamper is present), the system will arm the ready partition (-s) and
skip the unready one (-s). The system will then send an SMS text message, containing a list of violated zones/tampers, to user
phone number that the system arming was initiated from.
If a combination of armed and disarmed ready partitions is present, the system will arm the disarmed ready partitions and skip
the armed ones.
•
38
EN
MANUAL ELDES ESIM264 V3.1
The system will arm/disarm the partition corresponding to the one that the user phone number is assigned to. For more details on how to
set user phone number partition, please refer to 23.2. User Phone Number Partition.
30
CALL
User
ESIM264
12.2. SMS Text Message
SMS
To arm the system by SMS text message, send the following text to the system‘s phone number from any of 10 available user
phone numbers (see 8. USER PHONE NUMBERS for user phone number management). When the SMS text message for arming is sent to the system’s phone number, the system will proceed as follows:
•
•
Non-partitioned system:
•
If ready (no violated zone/tamper), the system will arm.
•
If unready, the system will not arm and provide a list of violated zones/tampers by SMS text message to user phone
number.
Partitioned system:
•
If all partitions are disarmed ready (no violated zone/tamper), the system will arm them.
•
If one or more partitions are disarmed unready (violated zone/tamper is present), the system will arm the ready partition (-s) and skip the unready one (-s). The system will then send an SMS text message, containing a list of violated
zones/tampers, to user phone number that the system arming was initiated from.
•
If a combination of armed and disarmed ready partitions is present, the system will arm the disarmed ready partitions
and skip the armed ones.
Arm the system
SMS text message content:
ssss_ARMp or ssss_ARMp,p
Value: ssss – 4-digit SMS password; p – partition number, range – [1 – Partition 0, 2 – Partition 1].
Example: 1111_ARM1
31
SMS
User
ESIM264
To disarm the system by SMS text message, send the following text to the system‘s phone number from any of 10 available user phone numbers:
Disarm the system
SMS text message content:
ssss_DISARMp or ssss_DISARMp,p
Value: ssss – 4-digit SMS password; p – partition number, [1 – Partition 0, 2 – Partition 1].
Example: 1111_DISARM1,2
32
SMS
User
MANUAL ELDES ESIM264 V3.1
ESIM264
EN
39
Regardless of the partition a user phone number is assigned to, the user will be able arm/disarm by SMS text message method either Partition 0 , Partition 1 or both partitions simultaneously.
12.3. EKB2 Keypad and User Password
READY message displayed in the home screen view by EKB2 keypad indicates that no violated zones and/or tampers are present, therefore the system can be armed. If the message is displayed as NOT READY, the user must restore all violated zones
and tampers before arming the system. Alternatively, the violated zones can be bypassed (see 14.7. Bypassing and Activating Zones), disabled (see 14.9. Disabling and Enabling Zones) or a Force attribute enabled (see 14.6. Zone Attributes).
To arm the system by EKB2 keypad, enter any out of 30 available 4-digit user passwords using the number keys on the keypad
(see 10. USER PASSWORDS for user password management).
EKB2
By default when a valid user password is entered, the system will initiate exit delay, the keypad’s buzzer will emit short beeps
and the keypad will display
icon next to the countdown timer. When the system is successfully armed, the keypad will
display
icon for 5 seconds and switch to home screen view.
Arm the system
1
2
3
4
5
6
7
8
9
0
Enter user password:
uuuu → OK
Value: uuuu – 4-digit user password; p – partition number, range –
[1... 4], part-name – up to 15 characters partition name.
Example: 1111 → OK
To cancel the system arming process, enter the user password again during exit delay countdown.
To disarm the system by EKB2 keypad, enter any out of 30 available 4-digit user passwords using the number keys on the keypad. By default, the system disarming process is as follows:
•
To disarm the system by EKB2 keypad, enter any out of 30 available 4-digit user passwords using the number keys on the keypad. When
a valid user password is entered, the keypad will display
icon for 3 seconds and switch to home screen view.
Disarm the system
1
2
3
4
5
6
7
8
9
0
Enter user password:
uuuu → OK
Value: uuuu – 4-digit user password; p – partition number, range –
[1... 4], part-name – up to 15 characters partition name.
Example: 1111 → OK
The system will arm/disarm the partition corresponding to the one that user password and the key­pad are assigned to. For example, if EKB2
keypad and user password is assigned to Partition 1, the user will be able to arm/ disarm only Partition 1. For more details on how to set user
password and keypad partition, please refer to 23.4. User Password Partition and 23.3. Keypad Partition and Keypad Partition Switch respectively.
To arm/disarm a different partition than the keypad is assigned to, use keypad partition switch feature (by default – disabled) before arming/
disarming process. For more details on keypad partition switch and how to enable it, please refer to 23.3. Keypad Partition and Keypad
Partition Switch.
Use keypad partition
switch
Menu path:
P1 → [p] part-name → OK
Value: part-name – up to 15 characters partition name.
NOTE: If the user fails to enter a correct user password 10 times in a row, the system will block the keypad for 2 minutes and the keypad will
display KEYPAD BLOCKED message. While the keypad is blocked, the system prevents from entering any user password. The keypad will
automatically unblock once the 2-minute time has expired and display KEYPAD UNBLOCKED message.
40
EN
MANUAL ELDES ESIM264 V3.1
12.4.EKB3 Keypad and User Password
EKB3
Illuminated indicator READY on EKB3 keypad indicates that no violated zones and/or tampers are present, therefore the system
can be armed. If the indicator is not illuminated, the user must restore all violated zones and tampers before arming the system.
Alternatively, the violated zones can be bypassed (see 14.7. Bypassing and Activating Zones), disabled (see 14.9. Disabling and Enabling Zones) or a Force attribute enabled (see 14.6. Zone Attributes).
To arm the system by EKB3 keypad, enter any out of 30 available 4-digit user passwords using the number keys on the keypad
(see 10. USER PASSWORDS for user password management). By default, when a valid user password is entered, the system
will initiate exit delay, the keypad’s buzzer will emit short beeps and the indicator ARMED will light ON. When the system is
successfully armed, the keypad’s buzzer will silent down.
Arm the system
1
2
3
4
5
6
7
8
9
Enter user password:
uuuu
Value: uuuu – 4-digit user password.
Example: 1111
0
To cancel the system arming process, enter the user password again during exit delay countdown.
To disarm the system by EKB3 keypad, enter any out of 30 available 4-digit user passwords using the number keys on the keypad. When a
valid user password is entered, EKB3 keypad indicator ARMED will light OFF.
Disarm the system
1
2
3
4
5
6
7
8
9
Enter user password:
uuuu
Value: uuuu – 4-digit user password.
Example: 1111
0
The system will arm/disarm the partition corresponding to the one that user password and the key­pad are assigned to. For example, if
EKB3 keypad and user password is assigned to Partition 0, the user will be able to arm/ disarm only Partition 0. For more details on how
to set user password and keypad partition, please refer to 23.4. User Password Partition and 23.3. Keypad Partition and Keypad
Partition Switch respectively.
To arm/disarm a different partition than the keypad is assigned to, use keypad partition switch feature (by default – disabled) to switch the
keypad to a different partition before arm­ing/disarming process. For more details on keypad partition switch and how to enable it, please
refer to 23.3. Keypad Partition and Keypad Partition Switch.
Use keypad partition
switch
Hold the [*] key, release it after 3 short beeps & enter partition number:
*p
Value: p – partition number, range – [0... 1]
Example: *1
NOTE: By default, User Password 1 is preset as 1111 and assigned to Partition 0.
MANUAL ELDES ESIM264 V3.1
EN
41
12.5. iButton Key
To arm or disarm the system, touch the iButton key reader by any of 5 available iButton keys (see 11. iBUTTON KEYS for iBut­
ton key management). When the iButton is touched to the iButton key reader for arming, the system will proceed as follows:
• If ready (no violated zone/tamper), the system will initiate exit delay and arm.
• If unready, the system will not arm and provide a list of violated zones/tampers by SMS text message to user phone
number. In such case the user must restore all violated zones and tampers before arming the system. Alternatively, the
violated zones can be bypassed (see 14.7. Bypassing and Activating Zones), disabled (see 14.9. Disabling and
Enabling Zones) or a Force attribute enabled (see 14.6. Zone Attributes).
33
The system will arm/disarm the partition corresponding to the one that the iButton key is assigned to. For more details on how
to set iButton key partition, please refer to 23.5. iButton Key Partition.
12.6.EWK1/EWK2 Wireless Keyfob
EWK1/
EWK2
To arm the system, press 1 of 4 keyfob buttons set to arm the system (by default, EWK1 –
EWK2 button is pressed for arming, the system will proceed as follows:
• If ready (no violated zone/tamper), the system will initiate exit delay and arm.
•
;EWK 2 -
). When EWK1/
If unready, the system will not arm and provide a list of violated zones/tampers by SMS text message to user phone
number. In such case the user must restore all violated zones and tampers before arming the system. Alternatively, the
violated zones can be bypassed (see 14.7. Bypassing and Activating Zones), disabled (see 14.9. Disabling and
Enabling Zones) or a Force attribute enabled (see 14.6. Zone Attributes).
35
34
Arm the
system
Arm the
system
To disarm the system, press 1 of 4 keyfob buttons set to disarm the system (by default, EWK1 -
).
37
36
Disarm
the
system
; EWK2 -
Disarm
the
system
The system will arm/disarm the partition corresponding to the one that EWK1/EWK2 wireless keyfob is assigned to (see 23.6.
EWK1/ EWK2 Wireless Keyfob Partition). For example, if EWK1/EWK2 wireless keyfob is assigned to Partition 1, the user
will be able to arm/ disarm only Partition 1. To arm a different partition than the EWK1/EWK2 wireless keyfob is assigned to,
bind another EWK1/EWK2 keyfob to the system and assign it to a different partition.
For more details on how to manage EWK1/EWK2 keyfob buttons, please refer to ELDES Configuration Tool software‘s HELP
section.
42
EN
MANUAL ELDES ESIM264 V3.1
12.7. Arm-Disarm by Zone
ARM/
DISARM
ZONE
The Arm-Disarm by Zone feature allows to use a zone for arming and disarming the alarm system when the zone is violated and
restored. The process is performed by providing a low-level pulse for more than 3 seconds into the specified zone. It means that
violating and restoring the zone leads to system arming and by repeating this action the system becomes disarmed. The system
will arm/disarm the partition (-s) that the zone is assigned to. This method can be set up for one on-board zone only.
Set zone for ArmDisarm by Zone
method
Disable Arm-Disarm by
Zone method
MANUAL ELDES ESIM264 V3.1
EKB2
Menu path:
OK → CONFIGURATION → OK → aaaa → OK → ZONES → OK → ARM/DISARM BY ZONE
→ OK → ZONE 1... 12 → OK
Value: aaaa – 4-digit administrator password.
EKB3
Enter parameter 34 & on-board zone number:
34 nn #
Value: nn – on-board zone number, range – [01... 12].
Example: 3403#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EKB2
Menu path:
OK → CONFIGURATION → OK → aaaa → OK → ZONES → OK → ARM/DISARM BY ZONE
→ OK → N/A → OK
Value: aaaa – 4-digit administrator password.
EKB3
Enter parameter 34 & parameter status value
34 00 #
Example: 3400#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EN
43
12.8.Disabling and Enabling Arm/Disarm Notifications
By default, when the system is successfully armed or disarmed, it replies with confirmation by SMS text message to:
•
user phone number, sharing the same partition as EKB2/EKB3 keypad and user password, iButton key, EWK1/EWK2 wireless keyfob or
zone, set up for Arm/Disarm by Zone method.
•
user phone number that the system arming/disarming by free of charge phone call was initiated from.
•
user phone number that the system arming/disarming by SMS text message was initiated from.
The confirmation SMS text message is sent to the user phone number regarding each partition separately and contains system status and
partition name.
To disable/enable this notification for individual user phone number, please refer to the following configuration methods.
Disable arm/disarm
notification for
individual user phone
number
Enable arm/disarm
notification for
individual user phone
number
EKB2
Menu path:
OK → CONFIGURATION → OK → aaaa → OK → PRIMARY SETTINGS → OK → CALL/SMS
SETTINGS → OK → USERS → OK → USER 1... 5 → OK → SEND ARM/DARM SMS → OK →
DISABLE → OK
Value: aaaa – 4-digit administrator password.
EKB3
Enter parameter 75, user phone number slot & parameter status value:
75 us 0 #
Value: us – user phone number slot, range – [01... 05].
Example: 75030#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EKB2
Menu path:
OK → CONFIGURATION → OK → aaaa → OK → PRIMARY SETTINGS → OK → CALL/SMS
SETTINGS → OK → USERS → OK → USER 1... 5 → OK → SEND ARM/DARM SMS → OK →
ENABLE → OK
Value: aaaa – 4-digit administrator password.
EKB3
Enter parameter 75, user phone number slot & parameter status value:
75 us 1 #
Value: us – user phone number slot, range – [01... 05].
Example: 75041#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
By default, the system sends SMS text message only to the first available user phone number when the system is successfully armed/
disarmed. If the system did not receive the SMS delivery report during 20 seconds, it will attempt to send the SMS text message to the next
preset user phone number. To ignore the SMS delivery report and allow/disallow the system to send the SMS text message to every preset
user phone number, please refer to the following configuration methods.
44
EN
MANUAL ELDES ESIM264 V3.1
Enable arm/disarm
notification for all
preset user phone
numbers
Disable arm/disarm
notification for all
preset user phone
numbers
MANUAL ELDES ESIM264 V3.1
EKB2
Menu path:
OK → CONFIGURATION → OK → aaaa → OK → PRIMARY SETTINGS → OK → CALL/SMS
SETTINGS → OK → SEND ARM/DARM ALL → OK → ENABLE → OK
Value: aaaa – 4-digit administrator password.
EKB3
Enter parameter 22 & parameter status value:
22 1 #
Example: 221#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EKB2
Menu path:
OK → CONFIGURATION → OK → aaaa → OK → PRIMARY SETTINGS → OK → CALL/SMS
SETTINGS → OK → SEND ARM/DARM ALL → OK → DISABLE → OK
Value: aaaa – 4-digit administrator password.
EKB3
Enter parameter 22 & parameter status value:
22 0 #
Example: 220#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EN
45
13.EXIT AND ENTRY DELAY
When arming, the system initiates the exit delay countdown (by default – 15 seconds) intended for the user to leave the secured area. The
exit delay is indicated by short beeps emitted by EKB2/EKB3 keypad buzzer and buzzer, connected to the alarm system. in addition, when
arming by EKB2 keypad,
icon will be displayed next to the countdown timer on keypad screen during exit delay.
•
a non-partitioned system,
•
a partitioned system, EKB2 keypad will display ARMING part-name message on the screen for 3 seconds and switch to partition
selection menu during exit delay.
icon will be displayed next to the countdown timer on EKB2 keypad screen during exit delay.
Exit delay is provided when arming the system by the following methods:
•
EKB2/EKB3 keypad and user password.
•
iButton key.
•
EWK1/EWK2 wireless keyfob.
•
Arm/Disarm by Zone.
To arm the system without exit delay, use one of the following system arming methods:
•
Free of charge phone call.
•
SMS text message.
•
EGR100 middle-ware.
Set exit delay
SMS
EKB2
SMS text message content:
ssss_EXITDELAY:ext
Value: ssss – 4-digit SMS password; ext – exit delay duration, range – [0... 600] seconds.
Example: 1111_EXITDELAY:20
Menu path:
OK → CONFIGURATION → OK → aaaa → OK → PRIMARY SETTINGS → OK → EXIT DELAY → OK
→ ext → OK
Value: aaaa – 4-digit administrator password;, ext – exit delay duration, range – [0... 600]
seconds.
EKB3
Enter parameter 72 & exit delay duration:
72 ext #
Value: ext – exit delay duration, range – [0... 600] seconds.
Example: 72259#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
NOTE: Alternatively, you can set exit delay value to 0 in order to arm the system without exit delay by any available method.
Once the exit delay has expired, the system initiates the entry delay countdown (by default – 15 seconds) if a Delay type zone is violated.
The countdown is indicated by short beeps emitted by keypad buzzer and by steady beep emitted by system’s buzzer. The indication is intended to advise the user that the system should be disarmed. Once the user presses/touches any key on the keypad during this delay, the
buzzer of the keypad will be silenced. If the system is disarmed before the entry delay expires, no alarm will be caused.
46
EN
MANUAL ELDES ESIM264 V3.1
Set entry delay for
Delay zone
SMS
EKB2
EKB3
Config
Tool
SMS text message content:
ssss_ENTRYDELAY:nn,eeeee or ssss_ENTRYDELAY:nn,eeeee;nn,eeeee;nn,eeeee;nn,eeeee
Value: ssss – 4-digit SMS password; nn – zone number, range – [1... 44], eeeee – entry delay
duration, range – [0... 65535] seconds.
Example: 1111_ENTRYDELAY:1,25;14,32;12,20
Menu path:
On-board zone: OK → CONFIGURATION → OK → aaaa → OK → ZONES → OK →
ONBOARD ZONES → OK → ZONE 1... 12 → OK → ENTRY DELAY → OK → eeeee → OK
Wireless zone: OK → CONFIGURATION → OK → aaaa → OK → ZONES → OK → WIRELESS
ZONES → OK → WLESS ZONE 1... 16 → OK → ENTRY DELAY → OK → eeeee → OK
Keypad zone: OK → CONFIGURATION → OK → aaaa → OK → ZONES → OK → KEYPAD ZONES
→ OK → KEYPAD 1... 4 ZONE → OK → ENTRY DELAY → OK → eeeee → OK
EPGM1 zone: OK → CONFIGURATION → OK → aaaa → OK → ZONES → OK → EPGM1 ZONES →
OK → EPGM1 ZONE 1... 16 → OK → ENTRY DELAY → OK → eeeee → OK
Value: aaaa – 4-digit administrator password; eeeee – entry delay duration, range – [0...
65535] seconds.
Enter parameter 54, partition number and entry delay duration:
54 nn eeeee #
Value: nn – zone number, range – [01... 44], eeeee – entry delay duration, range – [0... 65535]
seconds
Example: 5403259#
This operation may be carried out from the PC using the ELDES Configuration Tool software.
For more details on zone types, please refer to 14.5. Zone Type Definitions.
MANUAL ELDES ESIM264 V3.1
EN
47
14.ZONES
Detection devices such as motion detectors and door contacts are connected to the alarm system’s zone terminals. Once connected, the
associated zone’s parameters must be configured.
ESIM264 comes equipped with 6 on-board zones allowing to connect up to 6 detection devices. For more details regarding zone expansion,
please refer to 14.2. Zone Expansion.
ESIM264 zones are classified by 5 categories:
Description
Max. number of
zones per device
Max. number of
zones in total
On-board zones
Built-in wired zones of ESIM264 alarm system.
6/12*
6/12*
Keypad zones
Hardwired zones of EKB2/EKB3 keypad.
1
4
EPGM1 zones
Zones of EPGM1 - hardwired zone & PGM output expansion 16
module.
16
Wireless zones
Non-physical zones automatically created by connected 2**
wireless devices.
32***
Virtual zones
Non-physical zones intended for Panic button feature (alarm
activaton upon pressing the button) on EWK1/EWK2 wireless
keyfob. Virtual zones can be manually created using ELDES
Configuration Tool software.
32****
Zone category
32****
* - 6-Zone mode is enabled by default. ATZ mode doubles the on-board zone number and increases it to 12 in total.
** - Depends on the connected wireless device.
*** - Available only if no zones, EPGM1 zones and virtual zones are present.
**** - Available only if no zones, EPGM1 zones and wireless zones are present.
14.1. Zone Numbering
The zone numbers ranging from Z1 through Z12 are permanently reserved for on-board zones even when ATZ mode is disabled. The
Z13-Z44 zone numbers are automatically assigned in the chronological order to the created virtual zones and the devices connected to the
system: keypads, wireless devices, EPGM1 modules.
14.2. Zone Expansion
For additional detection device connection, the number of zones can be expanded by:
•
enabling the ATZ (Advanced Technology zone) mode (see 14.4. ATZ (Advanced Technology Zone) Mode).
•
connecting EPGM1 hardwired zone and PGM output expansion module (see 31.1.3. EPGM1 – Hardwired Zone & PGM Output Ex­
pansion Module).
•
connecting keypads (see 31.1.1. EKB2 – LCD Keypad and 31.1.2. EKB3 – LED Keypad).
•
binding wireless devices (see 19. WIRELESS DEVICES).
•
creating virtual zones (see ELDES Configuration Tool software’s Help section).
The maximum supported number of zones is 44.
14.3. 6-Zone Mode
By default, ESIM264 alarm system runs in the 6-Zone mode under zone connection Type 1 allowing to connect up to 6 detection devices
of NO (normally-open) type to the on-board zone terminals as indicated in the wiring diagram of Type 1. Once a different zone connection
type is set, the detection device wiring must be done according to the wiring diagram of the associated type. Available zone connection
types for the 6-Zone mode:
•
Type 1 – Parallel wiring of NO (normally-open) detection device with 5,6kΩ EOL (end-of-line) resistor.
•
Type 2 – Serial wiring of NC (normally-closed) detection device with 5,6kΩ EOL resistor.
•
Type 3 – Combination of serial and parallel wiring of tamper with 5,6kΩ EOL resistor and NC (normally-closed) detection device with
3,3kΩ EOL resistor.
For zone wiring diagrams of the 6-Zone mode, please refer to 2.3.2. Zone Connection Types.
48
EN
MANUAL ELDES ESIM264 V3.1
Set zone connection
type for 6-Zone mode
EKB2
EKB3
Config
Tool
Menu path:
OK → CONFIGURATION → OK → aaaa → OK → ZONES → OK → ZONE TYPE:6-ZONE M
→ OK → TYPE 1... 3 → OK
Value: aaaa – 4-digit administrator password.
Enter parameter 39 & number of zone connection type:
39 1 # – Type 1
39 2 # – Type 2
39 3 # – Type 3
Example: 392#
This operation may be carried out from the PC using the ELDES Configuration Tool software.
14.4.ATZ (Advanced Technology Zone) Mode
The ATZ mode is a software-based feature that doubles the number of on-board zones and enables two detection devices to be installed
per 1 zone terminal. Once this mode is enabled, the zone connection Type 4 is set automatically. The detection devices must be wired to
the on-board zone terminals as indicated in the wiring diagram of the associated zone connection type. Available zone connection types
for the ATZ mode:
•
Type 4 – Parallel wiring of 2 NC (normally-closed) detection devices with 5,6kΩ and 3,3kΩ EOL (end-of-line) resistors respectively.
5,6kΩ EOL resistor corresponds to zones ranging from Z1 through Z6, while 3,3kΩ EOL resistor corresponds to zones ranging from Z7
through Z12.
•
Type 5 – Combination of serial and parallel wiring of tamper with 5,6kΩ EOL resistor and 2 NC (normally-closed) detection devices with
5,6kΩ and 3,3kΩ EOL resistors respectively. 5,6kΩ EOL resistor corresponds to zones ranging from Z1 through Z6, while 3,3kΩ EOL
resistor corresponds to zones ranging from Z7 through Z12.
For zone wiring diagrams of the ATZ mode, please refer to 2.3.2. Zone Connection Types.
Enable ATZ mode
Disable ATZ mode
MANUAL ELDES ESIM264 V3.1
EKB2
Menu path:
OK → CONFIGURATION → OK → aaaa → OK → ZONES → OK → ATZ MODE → OK →
ENABLE → OK
Value: aaaa – 4-digit administrator password.
EKB3
Enter parameter 28 & parameter status value:
28 1 #
Example: 281#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EKB2
Menu path:
OK → CONFIGURATION → OK → aaaa → OK → ZONES → OK → ATZ MODE → OK →
DISABLE → OK
Value: aaaa – 4-digit administrator password.
EKB3
Enter parameter 28 & parameter status value:
28 0 #
Example: 280#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EN
49
Set zone connection
type for ATZ mode
EKB2
Menu path:
OK → CONFIGURATION → OK → aaaa → OK → ZONES → OK → ZONE TYPE:ATZ MODE →
OK → TYPE 4... 5 → OK
Value: aaaa – 4-digit administrator password.
EKB3
Enter parameter 38 & number of zone connection type:
38 1 # – Type 4
38 2 # – Type 5
Example: 381#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
NOTE: The ATZ mode applies to on-board zones only when enabled.
14.5. Zone Type Definitions
•
Interior Follower – The zone can be violated during exit and entry delay without causing an alarm. If the zone is violated before the
entry delay has begun, it will cause an instant alarm followed by single notification delivery even if the zone has been violated multiple
times or another Interior Follower-type zone has been violated while alarm period (by default - 1 minute) is in progress. The zone is
used where violating a zone during exit/entry delay is unavoidable. Typically, this zone is used for indoor protection devices, such as
motion detectors, installed close to the exit/entry doors.
•
Instant – The alarm is instantly caused if this zone is violated when the system is armed or during entry delay. This zone type is usually
used for doors, windows or other zones, and shock detectors.
•
24-Hour – When the system is either armed or disarmed, the zone will cause instant alarm if violated. Normally, this type of zone is
used for securing the areas that require constant supervisory.
•
Delay – This zone type can be violated during exit and entry delay without causing an alarm. If the zone is violated when the system
is armed, it will initiate entry delay countdown intended for the user to disarm the system. If the zone is left violated after the exit
delay expires, it will cause an instant alarm. If one more zone with Stay-enabled attribute exist and the Delay-type zone is not violated
and restored during exit delay, the system will be armed in Stay mode (see 15. STAY MODE). Typically, this zone type is used for door
contacts installed at designated exit/entry doors.
•
Fire – If this zone type is violated when the system is either armed or disarmed, the alarm will be instantly caused and the siren/bell will
emit pulsating sound. Typically, this zone type is used for flame and smoke detectors.
•
Panic/Silent – This zone operates the same as 24-Hour zone type, but the system will not activate the siren/bell and keypad buzzer if
violated. Normally, this zone type used for panic alarm buttons.
Set zone type for
individual zone
EKB2
EKB3
50
EN
Menu path:
On-board zone: OK → CONFIGURATION → OK → aaaa → OK → ZONES → OK → ONBOARD
ZONES → OK → ZONE 1... 12 → OK → TYPE → OK → INTERIOR FOLLOWER | INSTANT | 24HOUR | DELAY | FIRE | PANIC/SILENT → OK
Wireless zone: OK → CONFIGURATION → OK → aaaa → OK → ZONES → OK → WIRELESS
ZONES 1... 4 → OK → WLESS ZONE 1... 16 → OK → TYPE → OK → INTERIOR FOLLOWER |
INSTANT | 24-HOUR | DELAY | FIRE | PANIC/SILENT → OK
Keypad zone: OK → CONFIGURATION → OK → aaaa → OK → ZONES → OK → KEYPAD ZONES
→ OK → KEYPAD 1... 4 ZONE → OK → TYPE → OK → INTERIOR FOLLOWER | INSTANT | 24HOUR | DELAY | FIRE | PANIC/SILENT → OK
EPGM1 zone: OK → CONFIGURATION → OK → aaaa → OK → ZONES → OK → EPGM1 ZONES →
OK → EPGM1 ZONE 1... 16 → OK → TYPE → OK → INTERIOR FOLLOWER | INSTANT | 24-HOUR |
DELAY | FIRE | PANIC/ SILENT → OK
Value: aaaa – 4-digit administrator password.
Enter parameter 53, zone number & zone type number:
53 nn 1 # – Interior Follower
53 nn 2 # – Instant
53 nn 3 # –24-Hour
53 nn 4 # – Delay
53 nn 5 # – Fire
53 nn 6 # – Panic/Silent
Value: nn – zone number, range – [01... 44]
Example: 53125#
MANUAL ELDES ESIM264 V3.1
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
NOTE: The system will NOT activate siren/bell and keypad buzzer only when Panic/Silent zone type is violated.
14.6.Zone Attributes
•
Stay – If this attribute is enabled, the zone, regardless of type, will not cause an alarm if violated when the system is Stay armed. For
more details on arming the system in the Stay mode, please refer to 15. STAY MODE.
•
Force – This attribute determines whether the system can be armed or not while a zone is violated. If a zone with the Force attribute
enabled is left violated until the exit delay expires, it will be ignored. Once the system is armed and the zone is restored, the violation
will not be ignored and the zone will operate according to the determined type. For more details on zone types, please refer to 14.5.
Zone Type Definitions.
•
Delay, ms – This attribute determines the zone sensitivity level by delay time (By default – 800 milliseconds). If a zone is left triggered
until the delay time expires, the zone is considered violated.
•
Delay becomes Instant in Stay mode – This attribute determines whether or not any Delay type zone will operate as Instant type
zone when the system is armed in the Stay mode. When the system is fully armed, the Delay type zone will operate normally. For more
details on Delay and Instant zone types, please refer to 14.5. Zone Type Definitions.
•
Chime – This feature is used to emit 3 short beeps from the keypad buzzer and display
icon on EKB2 keypad screen whenever any
Delay type zone is violated. Typically, the feature is used for designated exit/entry doors to indicate the opening of the doors.
•
Alarm count to bypass – This attribute determines a number of times the zone can be violated until it is automatically bypassed.
For more details on zone bypassing and how to activate a bypassed zone, please refer to 14.7. Bypassing and Activating Zones.
Enable Stay attribute
for individual zone
EKB2
EKB3
MANUAL ELDES ESIM264 V3.1
Menu path:
On-board zone: OK → CONFIGURATION → OK → aaaa → OK → ZONES → OK → ONBOARD
ZONES → OK → ZONE 1... 12 → OK → STAY → OK → ENABLE → OK
Wireless zone: OK → CONFIGURATION → OK → aaaa → OK → ZONES → OK → WIRELESS
ZONES → OK → WLESS ZONE 1... 16 → OK → STAY → OK → ENABLE → OK
Keypad zone: OK → CONFIGURATION → OK → aaaa → OK → ZONES → OK → KEYPAD
ZONES → OK → KEYPAD 1... 4 ZONE → OK → STAY → OK → ENABLE → OK
EPGM1 zone: OK → CONFIGURATION → OK → aaaa → OK → ZONES → OK → EPGM1 ZONES →
OK → EPGM1 ZONE 1... 16 → OK → STAY → OK → ENABLE → OK
Value: aaaa – 4-digit administrator password.
Enter parameter 56, zone number & parameter status value:
56 nn 1 #
Value: nn – zone number, range – [01... 44].
Example: 56041#
EN
51
Config
Tool
Disable Stay attribute
for individual zone
Enable Force attribute
for individual zone
Disable Force
attribute for
individual zone
EKB2
EN
Menu path:
On-board zone: OK → CONFIGURATION → OK → aaaa → OK → ZONES → OK → ONBOARD
ZONES → OK → ZONE 1... 12 → OK → STAY → OK → DISABLE → OK
Wireless zone: OK → CONFIGURATION → OK → aaaa → OK → ZONES → OK → WIRELESS
ZONES → OK → WLESS ZONE 1... 16 → OK → STAY → OK → DISABLE → OK
Keypad zone: OK → CONFIGURATION → OK → aaaa → OK → ZONES → OK → KEYPAD
ZONES → OK → KEYPAD 1... 4 ZONE → OK → STAY → OK → DISABLE → OK
EPGM1 zone: OK → CONFIGURATION → OK → aaaa → OK → ZONES → OK → EPGM1
ZONES → OK → EPGM1 ZONE 1... 16 → OK → STAY → OK → DISABLE → OK
Value: aaaa – 4-digit administrator password.
EKB3
Enter parameter 56, zone number & parameter status value:
56 nn 0 #
Value: nn – zone number, range – [01... 44].
Example: 56190#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EKB2
Menu path:
On-board zone: OK → CONFIGURATION → OK → aaaa → OK → ZONES → OK → ONBOARD
ZONES → OK → ZONE 1... 12 → OK → FORCE → OK → ENABLE → OK
Wireless zone: OK → CONFIGURATION → OK → aaaa → OK → ZONES → OK → WIRELESS
ZONES → OK → WLESS ZONE 1... 16 → OK → FORCE → OK → ENABLE → OK
Keypad zone: OK → CONFIGURATION → OK → aaaa → OK → ZONES → OK → KEYPAD ZONES
→ OK → KEYPAD 1... 4 ZONE → OK → FORCE → OK → ENABLE → OK
EPGM1 zone: OK → CONFIGURATION → OK → aaaa → OK → ZONES → OK → EPGM1 ZONES →
OK → EPGM1 ZONE 1... 16 → OK → FORCE → OK → ENABLE → OK
Value: aaaa – 4-digit administrator password.
EKB3
Enter parameter 82, zone number & parameter status value:
82 nn 1 #
Value: nn – zone number, range – [01... 44].
Example: 82061#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EKB2
EKB3
52
This operation may be carried out from the PC using the ELDES Configuration Tool software.
Menu path:
On-board zone: OK → CONFIGURATION → OK → aaaa → OK → ZONES → OK → ONBOARD
ZONES → OK → ZONE 1... 12 → OK → FORCE → OK → DISABLE → OK
Wireless zone: OK → CONFIGURATION → OK → aaaa → OK → ZONES → OK → WIRELESS
ZONES → OK → WLESS ZONE 1... 16 → OK → FORCE → OK → DISABLE → OK
Keypad zone: OK → CONFIGURATION → OK → aaaa → OK → ZONES → OK → KEYPAD
ZONES → OK → KEYPAD 1... 4 ZONE → OK → FORCE → OK → DISABLE → OK
EPGM1 zone: OK → CONFIGURATION → OK → aaaa → OK → ZONES → OK → EPGM1 ZONES→
OK → EPGM1 ZONE 1... 16 → OK → STAY → OK → DISABLE → OK
Value: aaaa – 4-digit administrator password.
Enter parameter 82, zone number & parameter status value:
82 nn 0 #
Value: nn – zone number, range – [01... 44].
Example: 82110#
MANUAL ELDES ESIM264 V3.1
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
Set Delay, ms atrribute
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
Enable/disable Delay
becomes Instant in
Stay mode attribute
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
Disable Chime
attribute
EKB2
Enable Chime attribute
Set Alarm count to
bypass attribute for
individual zone
MANUAL ELDES ESIM264 V3.1
Menu path:
OK → CONFIGURATION → OK →aaaa → OK → ZONES → OK → CHIME → OK → DISABLE → OK
Value: aaaa – 4-digit administrator password.
EKB3
Enter parameter 32 & parameter status value:
32 0 #
Example: 320#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EKB2
Menu path:
OK → CONFIGURATION → OK → aaaa → OK → ZONES → OK → CHIME → OK → ENABLE → OK
Value: aaaa – 4-digit administrator password.
EKB3
Enter parameter 32 & parameter status value:
32 1 #
Example: 321#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EN
53
14.7. Bypassing and Activating Zones
ATTENTION: Zone bypassing and activation must be carried out without Configuration mode being activated by the EKB3 keypad.
Zone bypassing allows the user to deactivate a violated zone and arm the system without restoring the zone. If a bypassed zone is violated
or restored during exit/entry delay, or when then system is armed, it will be ignored. When a zone is bypassed, EKB3 keypad indi­cator BYPS
will light ON and EKB2 keypad will display BYP message in the home screen view.
Bypass individual
violated zone
EKB2
EKB3
Bypass all violated
zones
EKB2
Menu path:
OK → BYPASS → OK → BYPASS LIST 1... 3 → OK → Z1-zone-name... Z44-zone-name → OK →
BYPASS → OK K
Value: zone-name - up to 24 characters zone name.
Press the [BYPS] key, enter zone number & user password:
BYPS nn uuuu #
Value: nn – zone number, range – [01... 44]; uuuu – 4-digit user password.
Example: BYPS091111#
Menu path:
OK → BYPASS → OK → BYP VIOLATED ZONES → OK
The zone will stay bypassed until the system is disarmed. Once the system is disarmed, the corresponding zone state will be indicated on
the keypads (see 31.1.1. EKB2 – LCD Keypad and 31.1.2. EKB3 – LED Keypad) and Info SMS text message (see 26. SYSTEM INFORMATION. INFO SMS). Alternatively, the user can activate the bypassed zone by the following configuration methods.
Activate bypassed
zone
EKB2
EKB3
Menu path:
OK → BYPASS → OK → BYPASS LIST 1...3 → OK → Z1-zone-name... Z44-zone-name → OK →
UNBYPASS → OK
Value: zone-name - up to 24 characters zone name.
Press the [BYPS[ key, enter zone number & user password:
BYPS nn uuuu #
Value: nn – zone number, range – [01... 44]; uuuu – 4-digit user password.
Example: BYPS251111#
NOTE: Zones can only be bypassed and activated when the system is not armed.
14.8.Zone Names
Each zone has a name that can be customized by the user. Typically, the name specifies a device type connected to a determined zone
terminal, for Example: Kitchen doors opened. The zone names are used in SMS text messages that are sent to the user during alarm. the
By default, the zone names are: Z1 – Zone1, Z2 – Zone2, Z3 – Zone3, Z4 – Zone4 etc.
Set zone name
SMS
Config
Tool
View zone names
54
EN
SMS
SMS text message content:
ssss_Znn:zone-name
Value: ssss – 4-digit SMS password; nn – zone number, range – [1... 44]; zone-name – up to
24 characters zone name.
Example: 1111_Z3:Door sensor triggered
This operation may be carried out from the PC using the ELDES Configuration Tool software.
SMS text message content:
ssss_STATUS
Value: ssss – 4-digit SMS password.
Example: 1111_STATUS
MANUAL ELDES ESIM264 V3.1
EKB2
Config
Tool
EKB2:
Menu path:
On-board zone: OK → CONFIGURATION → OK → aaaa → OK → ZONES → OK → ONBOARD
ZONES → OK → ZONE 1... 12 → OK → NAME
Wireless zone: OK → CONFIGURATION → OK → aaaa → OK → ZONES → OK → WIRELESS
ZONES → OK → WLESS ZONE 1... 16 → OK → NAME
Keypad zone: OK → CONFIGURATION → OK → aaaa → OK → ZONES → OK → KEYPAD ZONES
→ OK → KEYPAD 1... 4 ZONE → OK → NAME
EPGM1 zone: OK → CONFIGURATION → OK → aaaa → OK → ZONES → OK → EPGM1 ZONES →
OK → EPGM1 ZONE 1... 16 → OK → NAME
Value: aaaa – 4-digit administrator password.
This operation may be carried out from the PC using the ELDES Configuration Tool software.
ATTENTION: Colon, semi-colon characters, parameter names and/or values, such as PSW, STATUS, ON, OFF etc. are NOT allowed in zone
names
NOTE: Multiple zone names can be set by a single SMS text message, Example: 1111_Z1:Kitchen doors opened;Z3:Movement in basement;Z4:Bedroom window opened
14.9.Disabling and Enabling Zones
By default, all zones, except keypad and virtual zones, are enabled. To permanently disable/enable an individual zone, please refer to the
following configuration methods.
Disable zone
SMS
EKB2
MANUAL ELDES ESIM264 V3.1
SMS text message content:
ssss_Znn:OFF
Value: ssss – 4-digit SMS password; nn – zone number, range – [1... 44].
Example: 1111_Z13:OFF
Menu path:
On-board zone: OK → CONFIGURATION → OK → aaaa → OK → ZONES → OK → ONBOARD
ZONES → OK → ZONE 1... 12 → OK → STATUS → OK → DISABLE → OK
Wireless zone: OK → CONFIGURATION → STATUS → aaaa → OK → ZONES → OK → WIRELESS
ZONES → OK → WLESS ZONE 1... 16 → OK → STATUS → OK → DISABLE → OK
Keypad zone: OK → CONFIGURATION → OK → aaaa → OK → ZONES → OK → KEYPAD ZONES
→ OK → KEYPAD 1... 4 ZONE → OK → STATUS → DISABLE → OK
EPGM1 zone: OK → CONFIGURATION → OK → aaaa → OK → ZONES → OK → EPGM1 ZONES →
OK → EPGM1 ZONE 1... 16 → OK → STATUS → DISABLE → OK
Value: aaaa – 4-digit administrator password.
EKB3
Enter parameter 52, zone number & parameter status value:
52 nn 0 #
Value: nn – zone number, range – [01... 44].
Example: 52360#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EN
55
Enable zone
SMS
EKB2
SMS text message content:
ssss_Znn:ON
Value: ssss – 4-digit SMS password; nn – zone number, range – [1... 44].
Example: 1111_Z6:ON
Menu path:
On-board zone: OK → CONFIGURATION → OK → aaaa → OK → ZONES → OK → ONBOARD
ZONES → OK → ZONE 1... 12 → OK → STATUS → OK → ENABLE → OK
Wireless zone: OK → CONFIGURATION → STATUS → aaaa → OK → ZONES → OK → WIRELESS
ZONES → OK → WLESS ZONE 1... 16 → OK → STATUS → OK → DISABLE → OK
Keypad zone: OK → CONFIGURATION → OK → aaaa → OK → ZONES → OK → KEYPAD ZONES
→ OK → KEYPAD 1... 4 ZONE → OK → STATUS → DISABLE → OK
EPGM1 zone: OK → CONFIGURATION → OK → aaaa → OK → ZONES → OK → EPGM1 ZONES →
EPGM1 ZONE 1... 16 → OK → STATUS → DISABLE → OK
Value: aaaa – 4-digit administrator password.
EKB3
Enter parameter 52, zone number & parameter status value:
52 nn 1 #
Value: nn – zone number, range – [01... 44].
Example: 52151#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
15.STAY MODE
Stay mode allows the user to arm and disarm the alarm system without leaving the secured area. If the zones with Stay attribute enabled
are violated when the system is Stay armed, no alarm will be caused. Typically, this feature is used when arming the system at home before
going to bed.
The system can be Stay armed under the following conditions:
•
If a zone with Stay attribute enabled is NOT violated during exit delay, the system will arm in Stay mode. When arming the system in
Stay mode under this condition, one of the available arming methods must be used that provide exit delay. For more details on these
methods, please refer to 13. EXIT AND ENTRY DELAY.
•
The system will instantly arm in Stay mode when using one of the following methods.
Arm the system in
Stay mode
EKB2
Menu path:
P2 → uuuu → OK
Value: uuuu – 4-digit user password.
EKB3
Press the [STAY] key & enter user password:
STAY uuuu
Value: uuuu – 4-digit user password.
Example: STAY1111
When the system is successfully armed in Stay mode, EKB2 keypad will display STAY message in the home screen view.
ATTENTION: System arming in Stay mode by the keypad must be carried out without Configuration mode being activated.
NOTE: The system can be armed in Stay mode, only if there is at least one zone with Stay attribute enabled.
NOTE: Stay mode is not supported by virtual zones.
For more details on how to enable Stay attribute for zone, please refer to 14.6. Zone Attributes.
56
EN
MANUAL ELDES ESIM264 V3.1
16.TAMPERS
The tamper circuit is a single closed loop such that a break in the loop at any point will cause a tamper alarm regardless of the system
status – armed or disarmed. During the tamper alarm, the system will activate the siren/bell and the keypad buzzer and send the SMS text
message to the preset user phone number. The system will cause tamper alarm under the following conditions:
•
If the enclosure of a detection device, siren/bell, metal cabinet or keypad is opened, the physical tamper switch will be triggered. By
default, indicated as Tamper x in the SMS text message (x = tamper number).
•
If the wireless signal is lost due to low signal level or low battery power on a certain wireless device and does not restore during 20
minute period. This event is identified as Wireless Signal Loss. By default, indicated as Tamper x * in the SMS text message (x = tamper
number; * = wireless signal loss).
By default, tamper alarm notification by SMS text message is enabled. To disable/enable tamper alarm notification, please refer to the
following configuration methods.
Disable tamper alarm
notification
Enable tamper alarm
notification
EKB2
Menu path:
Tamper alarm: OK → CONFIGURATION → OK → aaaa → OK → SMS MESSAGES → OK →
TAMPER EVENT → OK → DISABLE → OK
Wireless signal loss: OK → CONFIGURATION → OK → aaaa → OK → SMS MESSAGES → OK →
WLESS SIGN LOSS EV → OK → DISABLE → OK
Value: aaaa – 4-digit administrator password.
EKB3
Enter parameter 25, event number & parameter status value:
25 08 0 # - Tamper alarm
25 11 0 # - Wireless signal loss
Example: 25110#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EKB2
Menu path:
Tamper alarm: OK → CONFIGURATION → OK → aaaa → OK → SMS MESSAGES → OK →
TAMPER EVENT → OK → ENABLE → OK
Wireless signal loss: OK → CONFIGURATION → OK → aaaa → OK → SMS MESSAGES → OK →
WLESS SIGN LOSS EV → OK → ENABLE → OK
Value: aaaa – 4-digit administrator password.
EKB3
Enter parameter 25, event number & parameter status value:
25 08 1 # - Tamper alarm
25 11 1 # - Wireless signal loss
Example: 25081#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
For more details on how to view violated tamper, please refer to 17. ALARM INDICATIONS AND NOTIFICATIONS
16.1. Tamper Names
Each tamper has a name that can be customized by the user. The tamper names are used in SMS text messages that are sent to the user
during the tamper alarm. By default, the tamper names are: Tamper 1, Tamper 2, Tamper 3, Tamper 4 etc. To set a different tamper name,
please refer to the following configuration methods.
Manage tamper name
MANUAL ELDES ESIM264 V3.1
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EN
57
17.ALARM INDICATIONS AND NOTIFICATIONS
When a zone, depending on zone type (see 14.5. Zone Type Definitions), or tamper is violated, the system will cause an alarm. By default, the alarm duration is 1 minute (see 20. SIREN/BELL regarding the alarm duration). During the alarm, the system will follow this
pattern:
1. The system activates the siren/bell and the keypad buzzer.
a) The siren/bell will emit pulsating sound if the violated zone is of Fire type, otherwise the sound will be steady.
b) The keypad buzzer will emit short beeps.
c) Depending on violated zone type, EKB2 keypad will display BURGLARY ALARM message followed by one of the alarm messages in the
home screen view:
•
ALARM.
•
FIRE ALARM.
•
24H ALARM.
d) During the tamper alarm, EKB2 keypad will display TAMPER ALARM message in the home screen view.
e) If one or more zones are violated, EKB3 will light ON the corresponding violated zone indicator (-s) ranging from 1 through 12. Indicator SYSTEM will flash if one or more high-numbered zones are violated. If one or tampers are violated, indicator SYSTEM will light ON.
For more details on viewing violated high-numbered zone and tamper numbers by EKB3 keypad, please refer to 29. INDICATION OF
SYSTEM FAULTS.
2. The system attempts to send an SMS text message, containing the violated zone/tamper name (see 14.8. Zone Names on how to set
a zone name), to the first preset user phone number, sharing the same partition as the violated zone/tamper. The system will send SMS
text messages regarding each violated zone/tamper separately.
a) If the user phone number is unavailable and the system fails to receive the SMS delivery report during 20 seconds, it will attempt to
send the SMS text message to the next preset user phone number, assigned to the same partition as the previous one. The user phone
number may be unavailable due to the following reasons:
•
mobile phone was switched off.
•
was out of GSM signal coverage.
b) The system will continue sending the SMS text message to the next preset user phone numbers in the priority order until one is available. The system sends the SMS text message only once and will not return to the first user phone number if the last one was unavailable.
3.If enabled, the system attempts to ring the first user phone number, sharing the same partition as the violated zone/tamper. The system
will dial regarding each violated zone/tamper separately.
a) When the call is answered, the user will be able to listen on the mobile phone for approx. 30 seconds to what is happening in the area,
surrounding the alarm system. This feature will be available only if a microphone is connected to the system (see 25. REMOTE LISTENING AND 2-WAY VOICE COMMUNICATION).
b) The system will dial the next preset user phone number, assigned to the same partition, if the previous user was unavailable due to the
following reasons:
• mobile phone was switched off.
• mobile phone was out of GSM signal coverage.
• provided “busy” signal.
• user did not answer the call after several rings, predetermined by the GSM operator.
c) The system will continue dialing the next preset user phone numbers in the priority order until one is available. The system dials only
once and will not return to the first user phone number if the last one was unavailable.
d) The system will not dial the next preset user phone number if the previous one was available, but rejected the phone call.
To silent the siren/bell as well as to cease system phone calls and SMS text message sending to the user phone numbers, please disarm the
system (see 12. ARMING AND DISARMING).
View violated zones
58
EN
SMS
SMS text message content:
ssss_INFO
Value: ssss – 4-digit SMS password.
Example: 1111_INFO
EKB2
Menu path:
OK → VIOLATED ZONES → OK → ZONE 1... 44
MANUAL ELDES ESIM264 V3.1
View violated tampers
EKB3
Please, refer to illuminated zone indicators ranging from 1 through 12 on the keypad. The
flashing indicator SYSTEM stands for violated high-numbered zones (Z13-Z44). For more
details on violated high-numbered zone indication, please refer to 29. INDICATION OF SYS­
TEM FAULTS.
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
SMS
The systemwill automatically send an SMS text message, containing a violated tamper name,
to user phone number.
EKB2
Menu path:
OK → VIOLATED TAMPERS → OK → TAMPER 1... 44
EKB3
The illuminated indicator SYSTEM stands for system fault presence including violated tamper. For more details on violated tamper indication, please refer to 29. INDICATION OF SYSTEM FAULTS.
For more details details on how to disable/enable SMS text messages and phone calls to preset user phone number in case of alarm, please
refer to 17.1. Enabling and Disabling Alarm Notifications
ATTENTION: Phone calls to the preset user phone number in case of alarm are disabled by force when MS mode is enabled (see
30. Monitoring Station).
NOTE: If one or more zones/tampers are violated during the alarm, the system will attempt to send as many SMS text message and dial the
user phone number as many times as the zone/tamper was violated.
NOTE: If the system sent the SMS text message and/or dialed the user phone number after disarming the system, it means that the SMS
text message and/or phone call was queued up in the memory before the system was disarmed
17.1. Enabling and Disabling Alarm Notifications
By, default the system will ring the preset user phone numbers in case of alarm. To disable/enable this feature, please refer to the following
configuration methods.
Disable call in case of
alarm
Enable call in
case of alarm
EKB2
EKB3
Enter parameter 30 & parameter status value:
30 1#
Example: 301#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EKB2
EKB3
MANUAL ELDES ESIM264 V3.1
Menu path:
OK → CONFIGURATION → OK → aaaa → OK → PRIMARY SETTINGS → OK → CALL/SMS
SETTINGS → OK → CALL IN CASE ALARM → OK → DISABLE → OK
Value: aaaa – 4-digit administrator password.
Menu path:
OK → CONFIGURATION → OK → aaaa → OK → PRIMARY SETTINGS → OK → CALL/SMS
SETTINGS → OK → CALL IN CASE ALARM → OK → ENABLE → OK
Value: aaaa – 4-digit administrator password.
Enter parameter 30 & parameter status value:
30 0#
Example: 300#
EN
59
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
By, default the system will send SMS text message to preset user phone numbers in case of alarm. To disable/enable this feature, please
refer to the following configuration methods.
Disable SMS text
message in case of
alarm
Enable SMS text
message in case of
alarm
EKB2
Menu path:
OK → CONFIGURATION → OK → aaaa → OK → SMS MESSAGES → OK → ALARM EVENT → OK
→ DISABLE → OK
Value: aaaa – 4-digit administrator password.
EKB3
Enter parameter 25, event number & parameter status value:
25 0310 #
Example: 25010#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EKB2
Menu path:
OK → CONFIGURATION → OK → aaaa → OK → SMS MESSAGES → OK → ALARM EVENT → OK
→ ENABLE → OK
Value: aaaa – 4-digit administrator password.
EKB3
Enter parameter 25, event number & parameter status value:
25 01 1 #
Example: 25011#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
By default, the system sends SMS text message to the first available user in case of alarm. If the system did not receive the SMS delivery
report during 20 seconds, it will attempt to send the SMS text message to the next preset user phone number. To ignore the SMS delivery
report and allow/disallow the system to send the SMS text message to every preset user phone number, please refer to the following
configuration methods.
Enable SMS text
message to all preset
user phone numbers in
case of alarm
60
EN
SMS
SMS text message content:
ssss_SMSALL:ON
Value: ssss – 4-digit SMS password
Example: 1111_SMSALL:ON
EKB2
Menu path:
OK → CONFIGURATION → OK → aaaa → OK → PRIMARY SETTINGS → OK → CALL/SMS
SETTINGS → OK → SEND ALARM SMS ALL → OK → ENABLE → OK
Value: aaaa – 4-digit administrator password.
EKB3
Enter parameter 21 & parameter status value:
21 1 #
Example: 211#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
MANUAL ELDES ESIM264 V3.1
Disable SMS text
message to all preset
user phone numbers in
case of alarm
SMS
SMS text message content:
ssss_SMSALL:OFF
Value: ssss – 4-digit SMS password
Example: 1111_SMSALL:OFF
EKB2
Menu path:
OK → CONFIGURATION → OK → aaaa → OK → PRIMARY SETTINGS → OK → CALL/SMS
SETTINGS → OK → SEND ALARM SMS ALL → OK → DISABLE → OK
Value: aaaa – 4-digit administrator password.
EKB3
Enter parameter 21 & parameter status value:
21 0 #
Example: 210#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
By default, tamper alarm notification by SMS text message is enabled. For more details on how to disable/enable tamper alarm notification,
please refer to 16. TAMPERS.
ATTENTION: Regardles of the Call in Case of Alarm parameter status, the system will NOT ring the preset user phone number if the
system is connected to the monitoring station (see 30. MONITORING STATION) and/or when ELDES Smart Security feature is in use
(see 35. ELDES Smart Security).
MANUAL ELDES ESIM264 V3.1
EN
61
18.PROGRAMMABLE (PGM) OUTPUTS
A PGM output is a programmable output that toggles to its set up state when a specific event has occurred in the system, the scheduled
weekday and time has come or if the user has initiated the PGM output state change manually. Normally, PGM outputs can be used to open/
close garage doors, activate lights, heating, watering and much more. When a PGM output turns ON, the system triggers any device or relay
connected to it.
ESIM264 comes equipped with four open-collector PGM outputs allowing to connect up to four devices or relays. For more details on PGM
output expanding, please refer to 18.2. PGM Output Expansion.
ESIM264 PGM outputs are classified by 4 categories:
PGM output category
Description
Max. number of PGM
outputs per device
Max. number of PGM
outputs in total
On-board PGM Outputs
Built-in wired PGM outputs of ESIM264 alarm system.
4
4
EPGM8 PGM Outputs
PGM outputs of EPGM8 - hardwired PGM output expan8
sion module.
8
EPGM1 PGM Outputs
PGM outputs of EPGM1 - hardwired zone & PGM output
2
expansion module.
4
Wireless PGM Outputs
Non-physical PGM outputs automatically created by con2*
nected wireless devices.
32**
* - Depends on the connected wireless device.
** - Available only if no EPGM1 PGM outputs are present.
For PGM output wiring diagram, please refer to 2.3.6. Relay Finder® 40.61.9.12 with Terminal Socket 95.85.3.
18.1. PGM Output Numbering
The PGM output numbers ranging from C1 through C12 are permanently reserved for on-board PGM outputs even if EPGM8 module mode is
disabled. The C13-C44 PGM output number are automatically assigned in the chronological order to the devices connected to the system:
EPGM1 modules and wireless devices.
18.2.PGM Output Expansion
For additional electrical appliance connection, the number of PGM outputs can be expanded by:
•
connecting EPGM8 hardwired PGM output expansion module. (see 18.2.1. EPGM8 Mode and 31.3.1. EPGM8 – Hardwired PGM
Output Expansion Module)
•
connecting EPGM1 hardwired zone and PGM output expansion module (see 31.1.3. EPGM1 – Hardwired Zone & PGM Output Ex­
pansion Module).
•
binding the wireless devices (see 19. WIRELESS DEVICES).
The maximum supported PGM output number is 76.
18.2.1. EPGM8 Mode
EPGM8 is an expansion module, which expands the system with 8 additional hardwired PGM outputs. For more details on EPGM8 module
installation, please refer to 31.3.1. EPGM8 – Hardwired PGM Output Expansion Module.
Once the EPGM8 module is installed, the EPGM8 mode must be enabled.
Enable EPGM8 mode
62
EN
EKB2
Menu path:
OK → CONFIGURATION → OK → aaaa → OK → PGM OUTPUTS → OK → USING EPGM8 → OK
→ ENABLE → OK
Value: aaaa – 4-digit administrator password.
EKB3
Enter parameter 33 & parameter status value:
33 1 #
Example: 331#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
MANUAL ELDES ESIM264 V3.1
Disable EPGM8 mode
EKB2
Menu path:
OK → CONFIGURATION → OK → aaaa → OK → PGM OUTPUTS → OK → USING EPGM8 → OK
→ DISABLE → OK
Value: aaaa – 4-digit administrator password.
EKB3
Enter parameter 33 & parameter status value:
33 0 #
Example: 330#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
18.3.PGM Output Names
Each PGM output has a name that can be customized by the user. Typically, the name specifies a device type connected to a determined
PGM output, for Example: Lights. The name can be used instead of PGM output number when controlling the PGM output by SMS text
message. By default, the PGM output names are: C1 – Controll1, C2 – Controll2, C3 – Controll3, C4 – Controll4 etc.
Set PGM output name
SMS
Config
Tool
View PGM output
names
SMS
SMS text message content:
ssss_Coo:out-name
Value: ssss – 4-digit SMS password; oo – PGM output number, range – [1... 44]; out-name –
up to 16 characters PGM output name.
Example: 1111_C2:Lights
This operation may be carried out from the PC using the ELDES Configuration Tool software.
SMS text message content:
ssss_STATUS
Value: ssss – 4-digit SMS password.
Example: 1111_STATUS
EKB2
Menu path:
On-board PGM output: OK → CONFIGURATION → OK → aaaa → OK → PGM OUTPUTS → OK
→ ONBOARD OUTPUTS → OK → OUTPUT 1... 12 → OK → NAME
Value: aaaa – 4-digit administrator password.
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
ATTENTION: Space, colon, semi-colon characters, parameter names and/or values, such as PSW, STATUS, ON, OFF etc. are NOT allowed in
PGM output names.
18.4.Turning PGM Outputs ON and OFF
By default, all PGM outputs are turned OFF. To instantly turn ON/OFF an individual PGM output and set its state to ON/OFF when the system
starts-up, please refer to the following configuration methods.
Turn ON PGM output/
Set PGM output startup state as ON
MANUAL ELDES ESIM264 V3.1
SMS
SMS text message content:
ssss_Coo:ON or ssss_out-name:ON
Value: ssss – 4-digit SMS password; oo – PGM output number, range – [1... 76]; out-name –
up to 16 characters PGM output name.
Example: 1111_Lights:ON
EN
63
EKB2
Menu path:
On-board PGM output: OK → CONFIGURATION → OK → aaaa → OK → PGM OUTPUTS → OK
→ ONBOARD OUTPUTS → OK → OUTPUT 1... 12 → OK → STATUS → OK → ENABLED → OK
Value: aaaa – 4-digit administrator password.
Turn OFF PGM output/
Set PGM output startup state as OFF
EKB3
Enter parameter 61, PGM output number & parameter status value:
61 oo 1 #
Value: oo – PGM output number, range – [01... 76].
Example: 61031#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
SMS
EKB2
SMS text message content:
ssss_Coo:OFF or ssss_out-name:OFF
Value: ssss – 4-digit SMS password; oo – PGM output number, range – [1... 76]; out-name –
up to 16 characters PGM output name.
Example: 1111_C2:OFF
Menu path:
On-board PGM output: OK → CONFIGURATION → OK → aaaa → OK → PGM OUTPUTS → OK
→ ONBOARD OUTPUTS → OK → OUTPUT 1... 12 → OK → STATUS → OK → DISABLED → OK
Value: aaaa – 4-digit administrator password.
EKB3
Enter parameter 61, PGM output number & parameter status value:
61 oo 0 #
Value: oo – PGM output number, range – [01... 76].
Example: 61020#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
To instantly turn ON an individual PGM output for a determined time period and automatically turn it OFF when the time period expires,
please refer to the following configuration method.
Turn ON PGM output
for time period
SMS
SMS text message content:
ssss_Coo:ON:hr.mm.sc or ssss_out-name:ON:hr.mn.sc
Value: ssss – 4-digit SMS password; oo – PGM output number, range – [1... 76]; out-name
– up to 16 characters PGM output name; hr – hours, range – [00... 23]; mn – minutes, range
– [00... 59]; sc – seconds, range – [00... 59].
Example: 1111_C4:ON:10.15.35
To instantly turn OFF an individual PGM output for a determined time period and automatically turn it ON when the time period expires,
please refer to the following configuration method.
Turn OFF PGM output
for time period
SMS
SMS text message content:
ssss_Coo:OFF:00.00.sc or ssss_out-name:OFF:hr.mn.sc
Value: ssss – 4-digit SMS password;oo – PGM output number, range – [1... 76]; out-name
– up to 16 characters PGM output name; hr – hours, range – [00... 23]; mn – minutes, range
– [00... 59]; sc – seconds, range – [00... 59].
Example: 1111_Lights:OFF:00.00.23
When the PGM output is turned ON or OFF, the system will send a confirmation by SMS text message to the user phone number that the
SMS text message was sent from.
NOTE FOR EKB2/EKB3/CONFIG TOOL USERS: Only the startup state of the PGM output can be changed using these configuration
methods.
64
EN
MANUAL ELDES ESIM264 V3.1
NOTE: PGM output can be turned ON for a determined time period only when it is in OFF state
NOTE: PGM output can be turned OFF for a determined time period only when it is in ON state
NOTE: Multiple PGM outputs can be turned ON/OFF by a single SMS text message, Example: 1111_C1:ON C2:OFF Pump:ON C4:ON:00.20.25
18.5.PGM Output Control by Event and Scheduler
The PGM outputs can automatically operate when a specific event occurs in the system and/or when the scheduled weekday and time
comes.
PGM Output Actions
The automatic action of the determined PGM output can be set as follows:
•
Turn ON – Determines whether the PGM output is to be turned ON.
•
Turn OFF – Determines whether the PGM output is to be turned OFF.
•
Pulse – Determines whether the PGM output is to be turned ON for a set period of time in seconds.
System Events
The aforementioned PGM output action can be automatically carried out under the following events that have occurred in the system:
•
System armed – System is armed in a determined partition ranging from Partition 1 through 4 or any partition.
•
System disarmed – System is disarmed in a determined partition ranging from Partition 1 through 4 or any partition.
•
Alarm begins – Alarm begins in a determined partition ranging from Partition 1 through 4 or any partition.
•
Alarm stops – Alarm stops in a determined partition ranging from Partition 1 through 4 or any partition.
•
Temperature falls – Temperature falls below the set MIN value of a determined temperature sensor 1-8.
•
Temperature rises – Temperature rises above the set MAX value of a determined temperature sensor 1-8.
•
Zone violated – A determined zone ranging from Z1 through Z76 is violated.
•
Zone restored – A determined zone ranging from Z1 through Z76 is restored.
•
Scheduler starts – Determines Start Time of a selected scheduler 1-16.
•
Scheduler ends – Determines End Time of a selected scheduler 1-16.
The user can also set a custom text, which will be sent by SMS text message to user phone number when the automatic PGM output action
is carried out.
Schedulers
The system supports up to 16 schedulers that allow the PGM outputs to operate according to the day of the week and time. When the
scheduler, which includes the set weekday and time, is selected, the PGM output will operate according to it. Each scheduler includes the
following parameters:
•
Always – The scheduler is not in use.
•
At specified time – Determines whether weekday and time settings are enabled:
•
Start Time – Determines the point in time when the PGM output action can begin.
•
End Time – Determines the point in time when the PGM output action can complete.
•
On weekdays – Determines days in week when the PGM output action is valid.
Additional Conditions
Additional condition narrows down the chances for a determined automatic PGM output operation to be carried out. If this feature is enabled, the PGM output will become dependent on one more system event that must be occurred prior or must occur after the aforementioned system event. The PGM output will not operate until the chain of system events meets the set values:
•
System armed – System is armed in a determined partition ranging from 1 to 4 or any partition.
•
System disarmed – System is disarmed in a determined partition ranging from 1 to 4 or any partition.
•
Zone violated – A determined zone ranging from Z1 to 76 is violated.
•
Zone restored – A determined zone ranging from Z1 to Z76 is restored.
Example: PGM output C1 is set to be turned ON when zone Z6 is violated. The additional condition feature is enabled and set to allow this
action to be carried out only if system’s Partition 2 is disarmed. It means that the PGM output C1 will be turned ON when zone Z6 is violated,
but only if system’s Partition 2 is disarmed.
MANUAL ELDES ESIM264 V3.1
EN
65
Manage PGM output
control by event &
scheduler
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
NOTE: When both - a system event is determined and a scheduler is selected, the PGM output will operate only if the determined event has
occurred in the system during the scheduled time period.
ATTENTION: If the date and time are not set, the system will NOT be able to automatically control the PGM outputs. For more details on how
to set date and time, please refer to 9. DATE AND TIME.
18.6.Wireless PGM Output Type Definitions
•
Output – Operates as normal PGM output that can be controlled by the user or automatically by event and scheduler. Normally, this
type is used for any device or relay.
•
Siren – Operates as siren output that automatically activates during alarm. Typically, this type is used for bell/siren connected to EW1
wireless device.
Set output type for
individual wireless
PGM output
66
EN
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
MANUAL ELDES ESIM264 V3.1
19.WIRELESS DEVICES
ESIM264 system can be equipped with a wireless transmitter-receiver module EWT1 (see 32.1. EWT1 - Wireless Transmitter-Receiver)
for system extension capabilities. The module allows the user to easily bind up to 16 ELDES-made wireless devices to the system. This
includes the following:
•
EWP1 – wireless PIR sensor (motion detector).
•
EWD1 – wireless magnetic door contact.
•
EWD2 - magnetic door contact/shock sensor/water sensor
•
EWS1 and EWS3 – wireless indoor sirens.
•
EWS2 – wireless outdoor sirens.
•
EWK1 and EWK2 – wireless keyfobs.
•
EW1 – wireless zone and PGM output expansion module.
•
EW1B – wireless battery-powered zone and PGM output expansion module.
•
EWF1 - wireless smoke detector.
The wireless devices can operate at a range of up to 30 meters from the alarm system unit while inside the building and at up to 150
meters range in open areas. The wireless connection is two-way and operates in one of four available channels at 868MHz non-licensed
frequency range. The communication link between the wireless device and the alarm system is constantly supervised by a configurable
self-test period.
For more details on how to install the wireless devices, please refer to 32. ELDES WIRELESS DEVICES and RADIO SYSTEM INSTALLATION AND SIGNAL PENETRATION manual located at www.eldes.lt/download
19.1. Binding, Removing and Replacing Wireless Devicess
When the wireless device is switched ON, it will initiate the data transmission to the system within its wireless connection range. In order to
optimize battery power saving of the wireless device, the data transmission periods vary by itself while the device is switched ON, but still
unbound. The data transmission period of the wireless devices when the alarm system is switched OFF or if the wireless device is unbound
or removed is as follows:
•
•
EKB3W, EW1, EW1B, EWP1, EWS1, EWS2, EWS3, EWF1:
•
First 360 attempts after the device startup (reset) - every 10 seconds.
•
The rest of attempts - every 1 minute.
EWD1, EWD2:
•
First 360 attempts after the device startup (reset) - every 10 seconds.
•
The rest of attempts - every 2 minutes.
Once the wireless device is bound, it will attempt to exchange data with ESIM264 system. Due to battery saving reasons, all ELDES wireless
devices operate in sleep mode. The data exchange will occur instantly if the wireless device is triggered (zone alarm or tamper alarm) or periodically when the wireless device wakes up to transmit the supervision signal, identified as Test Time, to the system as well as to accept
the queued up command (if any) from the system. Example: The alarm occurred at 09:15:25 and the system queued up the command for
EWS2 siren to start sounding. By default, Test Time value of EWS2 siren is 7 seconds, therefore EWS2 siren will sound at 09:15:32.
By default, the Test Time period is as follows:
• EWD1: every 60 seconds.
•
EW1, EWD2, EWP1, EWF1: every 30 seconds.
•
EW1B: every 20 seconds.
•
EWS1, EWS2, EWS3: every 7 seconds.
To set a different Test Time value, please refer to the following configuration method.
Set Test Time
MANUAL ELDES ESIM264 V3.1
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EN
67
NOTE: Test Time affects the wireless device binding process due to the alarm system listening for the incoming data from the wireless
device. The system binds the wireless device only when the first data packet is received.
An 8-digit wireless device ID code will be required in order to bind the device to the system or to remove it from the system. The wireless
ID code is printed on a label, which can be located on the inner or outer side of the enclosure or on the printed circuit board (PCB) of the
wireless device.
To bind a wireless device, please refer to the following configuration methods.
Bind wireless device
to the system
SMS
Config
Tool
SMS text message content:
ssss_SET:wless-id
Value: ssss – 4-digit SMS password; wless-id – 8-digit wireless device ID code.
Example: 1111_SET:535185D
This operation may be carried out from the PC using the ELDES Configuration Tool software.
NOTE FOR EWK1/EWK2 USERS: When binding EWK1/EWK2 wireless keyfob, it is necessary to press several times any button/key on the
device.
Once a wireless device is bound, it occupies one of 32 available wireless device slots and the system adds one or two wireless zones and
wireless PGM outputs depending on the wireless device model.
To remove a wireless device, please refer to the following configuration methods.
Remove wireless
device from the
system
SMS
Config
Tool
SMS text message content:
ssss_DEL:wless-id
Value: ssss – 4-digit SMS password; wless-id – 8-digit wireless device ID code.
Example: 1111_DEL:535185D
This operation may be carried out from the PC using the ELDES Configuration Tool software.
Once a wireless device is removed from the system, please restore its default parameters and remove the batteries from it.
To replace an existing wireless device with a new same model device, please refer to the following configuration methods
Replace wireless
device
SMS
Config
Tool
SMS text message content:
ssss_REP:wless-id<oldwl-id
Value: ssss – 4-digit SMS password; wless-id – 8-digit wireless device ID code of the old device; oldwl-id - 8-digit wireless device ID code of the new device.
Example: 1111_REP:535185D<41286652
This operation may be carried out from the PC using the ELDES Configuration Tool software.
When a wireless device is successfully replaced with a new one, the configuration of the old wireless device remains.
NOTE: If you are unable to bind a wireless device, please restore the wireless device’s parameters to default and try again. For more details
on how to restore the default parameters, please refer to the user manual provided along with the wireless device or visit www.eldes.lt/en/
download to download the latest user manual
68
EN
MANUAL ELDES ESIM264 V3.1
ATTENTION: In order to correctly remove the wireless device from the system, the user must remove the device using SMS text message
or ELDES Configuration Tool software and restore the parameters of the wireless device to default afterwards. If only one of these actions
is carried out, the wireless device and the system will attempt to exchange data to keep the wireless connection alive. This leads to fast
battery power drain on the battery-powered wireless device.
19.2.Wireless Device Information and Signal Status Monitoring
Once a wireless device is bound, the user can view the following information of a determined wireless device:
•
Battery level (expressed in percentage).
•
Wireless signal strength (expressed in percentage).
•
Error rate (number of failed data transmission attempts in 10-minute period).
•
Firmware version.
To view the wireless device information, please refer to the following configuration methods.
View wireless device
information
SMS
EKB2
Config
Tool
SMS text message content:
ssss_RFINFO:wless-id or ssss_RFINFO:Znn
Value: wless-id – 8-digit wireless device ID code; nn – wireless zone number, range – [13...
76].
Example: 1111_RFINFO:535185D
Menu path:
Battery level: OK → CONFIGURATION → OK → aaaa → OK → WIRELESS DEVICES → OK →
wless-dev wless-id → OK → BATTERY
Wireless signal: OK → CONFIGURATION → OK → aaaa → OK → WIRELESS DEVICES → OK →
wless-dev wless-id → OK → SIGNAL
Error rate: OK → CONFIGURATION → OK → aaaa → OK → WIRELESS DEVICES → OK → wlessdev wless-id → OK → ERROR RATE
Firmware version: OK → CONFIGURATION → OK → aaaa → OK → WIRELESS DEVICES → OK →
wless-dev wless-id → OK → FW RELEASE
Value: aaaa – 4-digit administrator password; wless-dev – wireless device model; wless-id
– 8-digit wireless device ID code.
This operation may be carried out from the PC using the ELDES Configuration Tool software.
The system supports up to 16 wireless devices. To view the number of unoccupied wireless device slots in the system, please refer to the
following configuration methods
View unoccupied
wireless device slots
SMS
Config
Tool
SMS text message content:
ssss_STATUS_FREE
Example: 1111_STATUS_FREE
This operation may be carried out from the PC using the ELDES Configuration Tool software.
When the wireless signal between the system and a wireles device is lost and does not restore during 20 minute period, the system will
send notification by SMS text message to preset user phone number. By default, the notification regarding the wireless signal status is
enabled. To disable/enable this notification, please refer to 16. TAMPERS.
MANUAL ELDES ESIM264 V3.1
EN
69
19.3.Disabling and Enabling Siren if Wireless Signal is Lost
If a wireless device loses its wireless signal, the system will send notification by SMS text message to user phone number and activate
the siren/bell. By default, the siren will not be activated when wireless signal is lost. To enable/disable this feature, please refer to the
following configuration methods.
Enable Siren if
Wireless Signal is Lost
Disable Siren if
Wireless Signal is Lost
70
EN
EKB2
Menu path:
OK → CONFIGURATION → OK → aaaa → OK → PRIMARY SETTINGS → OK → SIREN SETTINGS
→OK → SRN IF WLESS LOSS → OK → ENABLE → OK
Value: aaaa – 4-digit administrator password.
EKB3
Enter parameter 76 & parameter status value:
76 1 #
Example: 761#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EKB2
Menu path:
OK → CONFIGURATION → OK → aaaa → OK → PRIMARY SETTINGS → OK → SIREN SETTINGS
→OK → SRN IF WLESS LOSS → OK → DISABLE → OK
Value: aaaa – 4-digit administrator password.
EKB3
Enter parameter 76 & parameter status value:
76 0 #
Example: 760#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
MANUAL ELDES ESIM264 V3.1
20.SIREN/BELL
When the system is in alarm state, the siren/bell will sound until the set time (By default – 1 minute) expires or until the system is disarmed.
To set the alarm duration, please refer to the following configuration methods.
Set alarm duration
View alarm duration
SMS
SMS text message content:
ssss_SIREN:t
Value: ssss – 4-digit SMS password; t – alarm duration, range – [0... 5] minutes.
Example: 1111_SIREN:4
EKB2
Menu path:
OK → CONFIGURATION → OK → aaaa → OK → PRIMARY SETT INGS → OK → SIREN SETTINGS
→ OK → ALARM DURATION → OK → tt → OK
Value: aaaa – 4-digit administrator password; tt – alarm duration, range – [1... 10] minutes.
EKB3
Enter parameter 10 & alarm duration:
10 tt #
Value: tt – alarm duration, range – [00... 10] minutes.
Example: 1007#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
SMS
SMS text message content:
ssss_SIREN
Value: ssss – 4-digit SMS password
Example: 1111_SIREN
EKB2
Menu path:
OK → CONFIGURATION → OK → aaaa → OK → PRIMARY SETT INGS → OK → SIREN SETTINGS
→ OK → ALARM DURATION
Value: aaaa – 4-digit administrator password.
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
For siren/bell wiring diagram, please refer to 2.3.3. Siren.
NOTE: 0 value disables the siren/bell.
NOTE: Due to battery power saving reasons, the wireless siren will sound for 1 minute regardless of the set alarm duration time, unless it is
set to 0.
MANUAL ELDES ESIM264 V3.1
EN
71
20.1.Bell Squawk
If enabled, the siren/bell indicates the completed system arming and disarming process. After the system is successfully armed, the siren/
bell will emit 2 short beeps and 1 long beep after the system is disarmed. To enable/disable the Bell Squawk feature, please refer to the
following configuration methods.
Enable Bell Squawk
Disable Bell Squawk
EKB2
Menu path:
OK → CONFIGURATION → OK → aaaa → OK → PRIMARY SETT INGS → OK → SIREN SETTINGS
→ OK → BELL SQUAWK → OK → ENABLE → OK
Value: aaaa – 4-digit administrator password.
EKB3
Enter parameter 29 & parameter status value:
29 1 #
Example: 291#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EKB2
Menu path:
OK → CONFIGURATION → OK → aaaa → OK → PRIMARY SETT INGS → OK → SIREN SETTINGS
→ OK → BELL SQUAWK → OK → DISABLE → OK
Value: aaaa – 4-digit administrator password.
EKB3
Enter parameter 29 & parameter statusvalue:
29 0 #
Example: 290#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
20.2.Indication by EWS2 Indicators
When enabled, the built-in LED indicators of EWS2 wireless outdoor siren will flash during the alarm. To enable/disable this feature, please
refer to the following configuration methods.
Enable EWS2 LED
indication
72
EN
EKB2
Menu path:
OK → CONFIGURATION → OK → aaaa → OK → PRIMARY SETT INGS → OK → SIREN SETTINGS
→ OK → EWS2 LED → OK → ENABLE → OK
Value: aaaa – 4-digit administrator password.
EKB3
Enter parameter 29 & parameter status value:
88 1 #
Example: 881#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
MANUAL ELDES ESIM264 V3.1
Disable EWS2 LED
indication
EKB2
Menu path:
OK → CONFIGURATION → OK → aaaa → OK → PRIMARY SETT INGS → OK → SIREN SETTINGS
→ OK → EWS2 LED → OK → DISABLE → OK
Value: aaaa – 4-digit administrator password.
EKB3
Enter parameter 29 & parameter status value:
88 0 #
Example: 880#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
20.3.EWF1 Interconnection
The interconnection feature automatically links all wireless smoke detectors to each other that are connected to the same alarm system
unit. When any EWF1 detects smoke, it sounds the alarm and sends the signal to the alarm system that causes an instant alarm along with
the rest of EWF1 wireless smoke detectors. The device that detected smoke will auto-reset when the smoke clears, while the rest of EWF1
detectors will sound in accordance with the set time period (by default - 30 seconds).
By default, the interconnection feature is enabled and the siren alarm duration is 30 seconds. To manage these parameters, please refer
to the following configuraiton methods.
Disable
interconnection
Enable
interconnection
Set EWF1 siren alarm
duration
EKB2
Menu path:
OK → CONFIGURATION → OK → aaaa → OK → PRIMARY SETT INGS → OK → SIREN SETTINGS
→ OK → EWF1 SIREN INTERC. → OK → DISABLE → OK
Value: aaaa – 4-digit administrator password.
EKB3
Enter parameter 29 & parameter status value:
50 0 #
Example: 500#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EKB2
Menu path:
OK → CONFIGURATION → OK → aaaa → OK → PRIMARY SETT INGS → OK → SIREN SETTINGS
→ OK → EWF1 SIREN INTERC. → OK → ENABLE → OK
Value: aaaa – 4-digit administrator password.
EKB3
Enter parameter 29 & parameter status value:
50 1 #
Example: 501#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
For more details on EWF1 wireless smoke detector, please refer to 32.9. EWF1 - Wireless Smoke Detector
MANUAL ELDES ESIM264 V3.1
EN
73
21.BACKUP BATTERY, MAINS POWER SUPPLY STATUS MONITORING AND MEMORY
The system may come equipped with a backup battery maintaining power supply of the system when the mains power supply is temporally
lost. The implemented feature allows the system to perform a self-test on the backup battery and notify User 1 by SMS text message as
well as to indicate system fault by the keypad (see 29. INDICATION OF SYSTEM FAULTS) if:
•
battery has failed and requires replacement – battery resistance is 2Ω or higher; self-tested every 24 hours.
•
battery power is running low – battery voltage is 10.5V or lower; constantly self-tested.
By default, all notifications regarding the backup battery status are enabled. To disable/enable a determined backup battery notification,
please refer to the following configuration methods.
Disable Battery Failed
notification
Enable Battery Failed
notification
Disable Low Battery
notification
74
EN
EKB2
Menu path:
OK → CONFIGURATION → OK → aaaa → OK → SMS MESSAGES → OK → BATTERY FAIL EVENT
→ OK → DISABLE → OK
Value: aaaa – 4-digit administrator password.
EKB3
Enter parameter 25, notification number & parameter status value:
25 09 0 #
Example: 25090#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EKB2
Menu path:
OK → CONFIGURATION → OK → aaaa → OK → SMS MESSAGES → OK → BATTERY FAIL EVENT
→ OK → ENABLE → OK
Value: aaaa – 4-digit administrator password.
EKB3
Enter parameter 25, notification number & parameter status value:
25 09 1 #
Example: 25091#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EKB2
Menu path:
OK → CONFIGURATION → OK → aaaa → OK → SMS MESSAGES → OK → LOW BATTERY EVENT
→ OK → DISABLE → OK
Value: aaaa – 4-digit administrator password.
EKB3
Enter parameter 25, notification number & parameter status value:
25 06 0 #
Example: 25060#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
MANUAL ELDES ESIM264 V3.1
Enable Low Battery
notification
EKB2
Menu path:
OK → CONFIGURATION → OK → aaaa → OK → SMS MESSAGES → OK → LOW BATTERY EVENT
→ OK → ENABLE → OK
Value: aaaa – 4-digit administrator password.
EKB3
Enter parameter 25, notification number & parameter status value:
25 061 #
Example: 25061#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
If the household electricity is unstable in the system installation area, the system may temporally lose its power supply and continue operating on the backup battery power. The system supervises the mains power supply and notifiies User 1 by SMS text message as well as
indicates system fault condition on the keypad (see 29. INDICATION OF SYSTEM FAULTS) when the mains power is lost. When the mains
power restores, the system will notify User 1 by SMS text message and the keypad will no longer indicate system fault.
By default, system notification by SMS text message regarding mains power supply status is enabled. To disable/enable this notification,
please refer to the following configuration methods.
NOTE: In case of low back-up battery, the system will send the SMS text message to the user and transmit the data message to the monitoring station, but will NOT indicate a system fault on the keypad.
Disable mains
power supply loss
notification
Enable mains power
supply restore
notification
MANUAL ELDES ESIM264 V3.1
EKB2
Menu path:
OK → CONFIGURATION → OK → aaaa → OK → SMS MESSAGES → OK → MAIN PWR LOSS EV →
OK → DISABLE → OK
Value: aaaa – 4-digit administrator password.
EKB3
Enter parameter 25, notification number & parameter status value:
25 04 0 #
Example: 25040#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EKB2
Menu path:
OK → CONFIGURATION → OK → aaaa → OK → SMS MESSAGES → OK → MAIN PWR LOSS EV →
OK → ENABLE → OK
Value: aaaa – 4-digit administrator password.
EKB3
Enter parameter 25, notification number & parameter status value:
25 04 1 #
Example: 25041#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EN
75
Disable mains
power supply restore
notification
Enable mains power
supply restore
notification
EKB2
Menu path:
OK → CONFIGURATION → OK → aaaa → OK → SMS MESSAGES → OK → MAIN PWR REST EV →
OK → DISABLE → OK
Value: aaaa – 4-digit administrator password.
EKB3
Enter parameter 25, notification number & parameter status value:
25 05 0 #
Example: 25050#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EKB2
Menu path:
OK → CONFIGURATION → OK → aaaa → OK → SMS MESSAGES → OK → MAIN PWR REST EV →
OK → ENABLE → OK
Value: aaaa – 4-digit administrator password.
EKB3
Enter parameter 25, notification number & parameter status value:
25 05 1 #
Example: 25051#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
By default, mains power supply loss and restore delay are 30 and 120 seconds respectively. To set a different mains power supply loss and
restore delay duration, please refer to the following configuration methods.
Set mains power
supply loss delay
Set mains power
supply restore delay
EKB2
Menu path:
OK → CONFIGURATION → OK → aaaa → OK → PRIMARY SETT INGS → OK → MAIN POWER
STATUS → OK → LOSS DELAY → OK → lllll → OK
Value: aaaa – 4-digit administrator password; lllll – mains power loss delay duration, range
- [0... 65535] seconds.
EKB3
Enter parameter 70 & loss delay duration:
70 lllll #
Value: lllll – mains power loss delay duration, range - [0... 65535] seconds.
Example: 7043#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EKB2
Menu path:
OK → CONFIGURATION → OK → aaaa → OK → PRIMARY SETT INGS → OK → MAIN POWER
STATUS → OK → RESTORE DELAY → OK → rrrrr → OK
Value: aaaa – 4-digit administrator password; rrrrr – mains power restore delay duration,
range - [0... 65535] seconds.
EKB3
Enter parameter 71 & restore delay duration:
71 rrrrr #
Value: rrrrr – mains power restore delay duration, range - [0... 65535] seconds.
Example: 71150#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
The configuration settings and event log records are stored in a built-in EEPROM memory, therefore even if the system is fully shut down,
the configuration and event log remain. For more details regarding the event log, please refer to 28. EVENT LOG
76
EN
MANUAL ELDES ESIM264 V3.1
22.GSM CONNECTION STATUS MONITORING
The system constantly supervises the GSM connection. When the GSM signal is lost, the system indicator NETW will light OFF, the keypad
will indicate system fault condition (see 29. INDICATION OF SYSTEM FAULTS) and the system will turn ON a determined PGM output if
the GSM signal is lost for a longer time period than the set delay value (By default – 180 seconds). Once the GSM signal restores, the keypad
will no longer indicate system fault and the determined PGM output will turn OFF.
By default, the PGM output for GSM signal loss indication is not set. To set the PGM output and delay duration for GSM signal loss indication,
please refer to the following configuration method.
Manage GSM signal
loss indication by PGM
output
MANUAL ELDES ESIM264 V3.1
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EN
77
23.PARTITIONS
ESIM264 system comes equipped with a partitioning feature that can divide the alarm system into two independently controlled areas
identified as Partition 0 through 1, which are all supervised by one alarm system unit. Partitioning can be used in installations where shared
alarm system is more practical, such as a house and a garage or within a single multi-storey building. When partitioned, each system element, like zone, user phone number, keypad, user password, iButton key and wireless keyfob can be assigned to one of the partitions. The
user will then be able to arm/disarm the system partition that the zones and arm/disarm method are assigned to.
23.1. Zone Partition
Zone partition determines which system partition (-s) the zone will operate in.
Set zone partition
EKB2
Menu path:
On-board zone: OK → CONFIGURATION → OK → aaaa → OK → ZONES → OK → ONBOARD
ZONES → OK → ZONE 1... 12 → OK → PARTITION → OK → PARTITION0... 1 → OK
Wireless zone: OK → CONFIGURATION → OK → aaaa → OK → ZONES → OK → WIRELESS
ZONES → OK → WLESS ZONE 1... 16 → OK → PARTITION → OK → PARTITION0... 1 → OK
Keypad zone: OK → CONFIGURATION → OK → aaaa → OK → ZONES → OK → KEYPAD
ZONES → OK → KEYPAD 1... 4 ZONE → OK → PARTITION → OK → PARTITION0... 1 → OK
EPGM1 zone: OK → CONFIGURATION → OK → aaaa → OK → ZONES → OK → EPGM1 ZONES →
OK → EPGM1 ZONE 1... 16 → OK → PARTITION → OK → PARTITION0... 1 → OK
Value: aaaa – 4-digit administrator password.
EKB3
Enter parameter 57, zone number & partition value:
57 nn p #
Value: nn – zone number, range – [01... 44]; p – partition number, range – [0... 1].
Example: 57031#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
23.2.User Phone Number Partition
User phone number partition determines which system partition (-s) can be armed/disarmed from a certain user phone number by dialing
system’s phone number.
Set user phone
number partition
78
EN
EKB2
Menu path:
OK → CONFIGURATION → OK → aaaa → OK → PRIMARY SETTINGS → OK → CALL/SMS
SETTINGS → OK → USERS → OK → USER 1... 5 → OK → PARTITION → OK→ PARTITION0... 1
→ OK
Value: aaaa – 4-digit administrator password.
EKB3
Enter parameter 59, user phone number slot & partition number:
59 us p #
Value: nn – zone number, range – [01... 44]; p – partition number, range – [0... 1].
Example: 59030#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
MANUAL ELDES ESIM264 V3.1
23.3.Keypad Partition and Keypad Partition Switch
Keypad partition determines which system partition the keypad will operate in. To identify which partition the keypad is operating in:
•
EKB2 – Refer to partition name (by default – PART0) indicated in home screen view.
•
EKB3 – Refer to the location of the illuminated indicator READY on the keypad. The indicator will be illuminated under section A or B,
which represent Partition 0 and Partition 1 respectively.
The keypad must be assigned to the same partition as the user password (see 23.4. User Password Partition) in order to arm/disarm
the system by the keypad. For more details on system arming/disarming by the keypad, please refer to 12.3. EKB2 Keypad and User
Password and 12.4. EKB3 Keypad and User Password.
Set keypad partition
EKB2
Menu path:
OK → CONFIGURATION → OK → aaaa → OK → PRIMARY SETTINGS → OK → KEYPAD
PARTITION → OK → KEYPAD PARTITION → OK → KEYPAD 1... 4 → OK → PARTITION 0... 1 →
OK
Value: aaaa – 4-digit administrator password;
EKB3
Enter parameter 51, keypad slot & partition number:
51 kk p #
Value: kk – keypad slot, range – [01... 04];p – partition number, range – [0... 1];
Example: 51062#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
Keypad partition switch allows to quickly change the keypad partition. When the keypad partition is changed and when 1 minute after the
last key-stroke/key-touch expires, the system will return to the preset keypad partition. Typically, this feature is used for viewing arm/
disarm status and alarms of a different partition or when arming/disarming a different system partition by EKB2/EKB3 keypad than the
keypad is assigned to.
By default, keypad partition switch is disabled. To enable/disable this feature, please refer to the following configuration methods.
Enable keypad
partition switch
Disable keypad
partition switch
EKB2
Menu path:
OK → CONFIGURATION → OK → aaaa → OK → PRIMARY SETTINGS → OK → KEYPAD
PARTITION → OK → PARTITION SWITCH → OK → ENABLE → OK
Value: aaaa – 4-digit administrator password.
EKB3
Enter parameter 77 & parameter status value:
77 1#
Example: 771#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EKB2
Menu path:
OK → CONFIGURATION → OK → aaaa → OK → PRIMARY SETTINGS → OK → KEYPAD
PARTITION → OK → PARTITION SWITCH → OK → DISABLE → OK
Value: aaaa – 4-digit administrator password.
EKB3
Enter parameter 77 & parameter status value:
77 0 #
Example: 770#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
NOTE: Keypad partition switch can only be used when the system is partitioned.
MANUAL ELDES ESIM264 V3.1
EN
79
23.4. User Password Partition
User password partition determines which system partition can be armed/disarm using a certain user password. User password must be
assigned to the same partition as the keypad (see 23.3. Keypad Partition and Keypad Partition Switch) in order to arm/disarm the
system by EKB2/EKB3 keypad . For more details on system arming/disarming by the keypad, please refer to 12.3. EKB2 Keypad and User
Password and 12.4. EKB3 Keypad and User Password.
Set user password
partition
EKB2
Menu path:
User password 1... 16: OK → CONFIGURATION → OK → aaaa → OK → PRIMARY SETTINGS
→ OK → PASSWORDS → OK → USER PASSWORDS → OK → USER PSW (1-16) → OK → USER
PASSWORD 1... 16 → OK → PARTITION → OK → PARTITION0... 1 → OK
User password 17... 30: OK → CONFIGURATION → OK → aaaa → OK → PRIMARY SETTINGS
→ OK → PASSWORDS → OK → USER PASSWORDS → OK → USER PSW (17-30) → OK → USER
PASSWORD 17... 30 → OK → PARTITION → OK → PARTITION0... 1 → OK
Value: aaaa – 4-digit administrator password.
EKB3
Enter parameter 87, user password & partition number:
87 uuuu p #
Value: uuuu – 4-digit user password; p – partition number, range – [0... 1].
Example: 8711110#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
23.5.iButton Key Partition
iButton key partition determines which system partition can be armed/disarmed using a certain key. iButton key must be assigned to the
partition (-s) that the user desires to arm. For more details on system arming/disarming by iButton key, please refer to 12.5. iButton Key.
Set iButton key
partition
EKB2
Menu path:
OK → CONFIGURATION → OK → aaaa → OK → IBUTTON KEYS → OK → IBUTTON 1... 5 → OK →
PARTITION → OK → PARTITION0... 1 → OK
Value: aaaa – 4-digit administrator password.
EKB3
Enter parameter 60, iButton key slot & partition value:
60 ii p #
Value: ii – iButton key slot, range – [01... 05]; p – partition number, range – [0... 1].
Example: 60051#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
23.6.EWK1/EWK2 Wireless Keyfob Partition
EWK1/EWK2 wireless keyfob partition determines which system partition can be armed/disarmed using a certain EWK1/EWK2 wireless
keyfob. For more details on system arming/disarming by EWK1/EWK2 wireless keyfob, please refer to 12.6. EWK1/EWK2 Wireless Keyfob.
Set EWK1/EWK2
partition
80
EN
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
MANUAL ELDES ESIM264 V3.1
24.TEMPERATURE SENSORS
The system may be equipped with a temperature sensor intended for temperature measurement in the surrounding area. This feature
allows to monitor the temperature in real-time and receive a notification by SMS text message to User 1 phone number when the set
temperature boundaries are exceeded.
24.1.Adding, Removing and Replacing Temperature Sensors
To add a temperature sensor to the system, do the following:
a) Shutdown the system.
b) Wire up the temperature sensor to the 1-Wire interface terminals (see 2.3.5. Temperature Sensor and iButton Key Reader for
temperature sensor wiring diagram).
c) Power up the system.
The real-time temperature value of the temperature sensor is included in the Info SMS text message (see 26. SYSTEM INFORMATION.
INFO SMS) as well as it is indicated in the home screen view of EKB2 keypad.
To view the real-time temperature value measured by the temperature sensor, please refer to the following configuration methods.
View real-time
temperature value
SMS
EKB2
SMS text message content:
ssss_INFO
Value: ssss – 4-digit SMS password.
Example: 1111_INFO
Refer to home screen view on the keypad.
24.2.Setting Up MIN and MAX Temperature Boundaries. Temperature Info SMS
The system supports an SMS text message identified as the Temperature Info SMS, which is automatically delivered to User 1 phone number if the preset minimum (MIN) or maximum (MAX) temperature boundary of any temperature sensor is exceeded.
To set the MIN and MAX temperature boundaries for a certain temperature sensor, please refer to the configuration methods.
Set MIN and MAX
temperature
boundaries
SMS
EKB2
EKB3
Config
Tool
MANUAL ELDES ESIM264 V3.1
SMS text message content:
ssss_TEMP:mnn:mxx
Value: ssss – 4-digit SMS password; mnn – MIN boundary, range – [-55... 125] C; mxx - MAX
boundary, range – [-55... 125] C.
Example: 1111_TEMP:-5:28
Menu path:
MIN: OK → CONFIGURATION → OK → aaaa → OK → PRIMARY SETTINGS → OK →
TEMPERATURE SENSOR → OK → TEMP. MIN → OK → mnn → OK
MAX: OK → CONFIGURATION → OK → aaaa → OK → PRIMARY SETTINGS → OK →
TEMPERATURE SENSOR → OK → TEMP. MAX → OK → mxx → OK
Value: aaaa – 4-digit administrator password; mnn – MIN boundary, range – [-55... 125] C;
mxx - MAX boundary, range – [-55... 125] C.
Keys P1 or P2 are used to enter minus character, e.g. -20.
Enter parameter 19 & temperature boundary value:
19 mnn mxx #
Value: mnn – MIN boundary, range – [-55... 125] C; mxx - MAX boundary, range – [-55... 125]
C. 00 value stands for minus character, e. g. 0020 = -20
Example: 19001532#
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EN
81
View MIN and
MAX temperature
boundaries
SMS
EKB2
Config
Tool
SMS text message content:
ssss_TEMP
Value: ssss – 4-digit SMS password.
Example: 1111_TEMP
Menu path:
MIN: OK → CONFIGURATION → OK → aaaa → OK → PRIMARY SETTINGS → OK →
TEMPERATURE SENSOR → OK → TEMP. MIN
MAX: OK → CONFIGURATION → OK → aaaa → OK → PRIMARY SETTINGS → OK →
TEMPERATURE SENSOR → OK → TEMP. MAX
Value: aaaa – 4-digit administrator password.
This operation may be carried out from the PC using the ELDES Configuration Tool software.
By default, Temperature Info SMS is enabled. To disable/enable it, please refer to the following configuration methods.
Disable Temperature
Info SMS
SMS
EKB2
EKB3
Config
Tool
Enable Temperature
Info SMS
EKB2
EKB3
Config
Tool
82
EN
SMS text message content:
ssss_TEMP:00:00
Value: ssss – 4-digit SMS password.
Example: 1111_TEMP:00:00
Menu path:
Temperature fallen: OK → CONFIGURATION → OK → aaaa → OK → SMS MESSAGES → OK →
TEMP LOW EVENT → OK → DISABLE → OK
Temperature exceeded: OK → CONFIGURATION → OK → aaaa → OK → SMS MESSAGES → OK
→ TEMP HIGH EVENT → OK → DISABLE → OK
Value: aaaa – 4-digit administrator password.
Enter parameter 24, event number & parameter status value:
25 14 0 # - Temperature fallen
25 15 0 # - Temperature exceeded
Example: 25140#
This operation may be carried out from the PC using the ELDES Configuration Tool software.
Menu path:
Temperature fallen: OK → CONFIGURATION → OK → aaaa → OK → SMS MESSAGES → OK →
TEMP LOW EVENT → OK → ENABLE → OK
Temperature exceeded: OK → CONFIGURATION → OK → aaaa → OK → SMS MESSAGES → OK
→ TEMP HIGH EVENT → OK → ENABLE → OK
Value: aaaa – 4-digit administrator password.
Enter parameter 24, event number & parameter status value:
25 14 1 # - Temperature fallen
25 15 1 # - Temperature exceeded
Example: 25151#
This operation may be carried out from the PC using the ELDES Configuration Tool software.
MANUAL ELDES ESIM264 V3.1
25.REMOTE LISTENING AND 2-WAY VOICE COMMUNICATION
ESIM264 comes equipped with a microphone that allows the user to listen on his mobile phone to what is happening in the secured area.
By installing one of the audio modules EA1 or EA2, the user will be able to have a 2-way voice communication (see 31.3.2. EA1 – Audio
Output Module and 31.3.3. EA2 – Audio Output Module with Amplifier). Remote listening and 2-way voice communication can operate under the following conditions:
•
The system makes a phone call to a preset user phone number in case of alarm and the user answers the call.
•
The user initiates remote listening by sending the SMS text message, the system makes a phone call to the user phone number that the
SMS text message was sent from and the user answers the call.
Initiate remote
listening
SMS
SMS text message content:
ssss_MIC
Value: ssss – 4-digit administrator password
Example: 1111_MIC
Set microphone gain
EKB2
Menu path:
OK → CONFIGURATION → OK → aaaa → OK → PRIMARY SETT INGS → OK → GSM AUDIO → OK
→ MICROPHONE GAIN → OK → mg → OK
Value: aaaa – 4-digit administrator password; mg – microphone gain, range – [0... 15].
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EKB2
Menu path:
OK → CONFIGURATION → OK → aaaa → OK → PRIMARY SETT INGS → OK → GSM AUDIO → OK
→ SPEAKER LEVEL → OK → sl → OK
Value: aaaa – 4-digit administrator password; sl – speaker level, range – [0... 85].
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
Set speaker level
ATTENTION: Phone calls to the preset user phone number in case of alarm are disabled by force when MS mode is enabled
(see 30. MONITORING STATION).
MANUAL ELDES ESIM264 V3.1
EN
83
26.SYSTEM INFORMATION. INFO SMS
The system supports an informational SMS text message identified as the Info SMS, which can be delivered upon request. Once requested,
the system will reply with Info SMS that provides the following:
•
System date & time.
•
System status: partition armed (ON)/disarmed (OFF).
•
GSM signal strength.
•
Mains power supply status.
•
Temperature of the area surrounding the temperature sensor (if any).
•
State of zones (OK/alarm).
•
Name and status (ON/OFF) of PGM outputs.
Request for system
information
SMS
Config
Tool
SMS text message content:
ssss_INFO
Value: ssss – 4-digit SMS password.
Example: 1111_INFO
This operation may be carried out from the PC using the ELDES Configuration Tool software.
26.1.Periodic Info SMS
By default, the system sends Info SMS to User 1 phone number periodically once a day at 11:00 (frequency – 1 day; time – 11). The minimum period is every 1 hour (frequency – 0 days; time – 1). Typically, this feature is used to verify the power supply and online status of the
system.
To set a different frequency and time or disable periodic Info SMS, please refer to the following configuration methods.
Set periodic Info SMS
frequency and time
SMS
EKB2
EKB3
Config
Tool
Disable periodic Info
SMS
SMS
EKB2
84
EN
SMS text message content:
ssss_INFO:fff:it
Value: ssss – 4-digit SMS password; fff – frequency, range – [00... 99] days; it – time, range
– [01... 23].
Example: 1111_INFO:3.15
Menu path:
Frequency: OK → CONFIGURATION → OK → aaaa → PRIMARY SETTINGS → OK → INFO SMS
SCHEDULER → OK → FREQUENCY (DAYS) → fff → OK
Time: OK → CONFIGURATION → OK → aaaa → PRIMARY SETTINGS → OK → INFO SMS
SCHEDULER → OK → TIME → it → OK
Value: aaaa – 4-digit administrator password; fff – frequency, range – [00... 125] days; it –
time, range – [01... 23].
Enter parameter 11, time & frequency:
11it fff #
Value: it – time, range – [01... 23]; fff – frequency, range – [00... 125] days.
Example: 110412#
This operation may be carried out from the PC using the ELDES Configuration Tool software.
SMS text message content:
ssss_INFO:00:00
Example: 1111_INFO:00.00
Menu path:
Frequency: OK → CONFIGURATION → OK → aaaa → PRIMARY SETTINGS → OK → INFO SMS
SCHEDULER → OK → FREQUENCY (DAYS) → 0 → OK
Time: OK → CONFIGURATION → OK → aaaa → PRIMARY SETTINGS → OK → INFO SMS
SCHEDULER → OK → TIME → 0 → OK
Value: aaaa – 4-digit administrator password.
MANUAL ELDES ESIM264 V3.1
EKB3
Enter parameter 11, time & frequency:
11 00 00 #
Example: 110000#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
ATTENTION: Unlike Info SMS upon request, periodic Info SMS text message does not included zone states, PGM output names and status.
MANUAL ELDES ESIM264 V3.1
EN
85
27.SYSTEM NOTIFICATIONS
In case of a certain event, the system attempts to send an SMS text message to the first preset user phone number only. If the user phone
number is unavailable and the system fails to receive the SMS delivery report during 20 seconds, it will attempt to send the SMS text message to the next preset user phone number, assigned to the same partition as the previous one. The user phone number may be unavailable
due to the following reasons:
•
mobile phone was switched off.
•
was out of GSM signal coverage.
The system will continue sending the SMS text message to the next preset user phone numbers in the priority order until one is available.
The system sends the SMS text message only once and will not return to the first user phone number if the last one was unavailable.
The following table provides the description of system notifications by SMS text message sent to the user phone number.
Seq. No.
1
2
3
4
5
6
7
8
9
10
11
12
14
15
Event
General alarm
System disarmed
System armed
Mains power loss S
Mains power restore
Low battery
Periodical info
Tamper alarm
Battery failed
Description
SMS text message sent to the user in case of system alarm occurrence.
SMS text message sent to the user about disarmed system.
SMS text message sent to the user regarding armed system.
SMS text message sent to the user in case the backup battery voltage is 10.5V or lower.
SMS text message sent to the user in case the mains power supply is restored
SMS text message sent to the user in case the backup battery voltage is 10.5V or lower
Info SMS text message sent to the user periodically by the set values.
SMS text message sent to the user in case of tamper violation. Indicated as Tamper x.
SMS text message sent to the user in case the backup battery resistance is 2Ω or higher (battery
requires replacement).
System started
SMS text message sent to the user on system startup.
Wireless signal loss
SMS text message sent to the user in case the wireless signal is lost. Indicated as Tamper x *.
Temperature fallen
SMS text message sent to the user in case of temperature deviation by the set MIN value.
Temperature exceeded SMS text message sent to the user in case of temperature deviation by the set MAX value.
System shutdown
When the system is running on backup battery power, it sends the SMS text message to the user
before the backup battery power is fully depleted.
ATTENTION: The following methods provide the configuration of the master parameters, which override the notification parameters
described in 12.9. Disabling and Enabling Arm/Disarm Notifications.
86
EN
MANUAL ELDES ESIM264 V3.1
To disable/enable a certain system notification, please refer to the following configuration methods.
Disable system
notification
EKB2
EKB3
Config
Tool
MANUAL ELDES ESIM264 V3.1
Menu path:
General alarm: OK → CONFIGURATION → OK → aaaa → OK → SMS MESSAGES → OK →
ALARM EVENT → OK → DISABLE → OKK
System armed: OK → CONFIGURATION → OK → aaaa → OK → SMS MESSAGES → OK →
ARMED EVENT → OK → DISABLE → OK
System disarmed: OK → CONFIGURATION → OK → aaaa → OK → SMS MESSAGES → OK →
DISARMED EVENT → OK → DISABLE → OK
Mains power loss: OK → CONFIGURATION → OK → aaaa → OK → SMS MESSAGES → OK →
MAIN PWR LOSS EV → OK → DISABLE → OK
Mains power restore: OK → CONFIGURATION → OK → aaaa → OK → SMS MESSAGES → OK →
MAIN PWR REST EV → OK → DISABLE → OK
Low battery: OK → CONFIGURATION → OK → aaaa → OK → SMS MESSAGES → OK → LOW
BATTERY EVENT → OK → DISABLE → OK
Battery failed: OK → CONFIGURATION → OK → aaaa → OK → SMS MESSAGES → OK →
BATTERY FAIL EVENT → OK → DISABLE → OK
Periodical info: OK → CONFIGURATION → OK → aaaa → OK → SMS MESSAGES → OK →
PERIODIC SMS EV → OK → DISABLE → OK
Tamper alarm: OK → CONFIGURATION → OK → aaaa → OK → SMS MESSAGES → OK →
TAMPER EVENT → OK → DISABLE → OK
System started: OK → CONFIGURATION → OK → aaaa → OK → SMS MESSAGES → OK →
SYSTEM STARTED EV → OK → DISABLE → OK
Wireless signal loss: OK → CONFIGURATION → OK → aaaa → OK → SMS MESSAGES → OK →
WLESS SIGN LOSS EV → OK → DISABLE → OK
System shutdown: OK → CONFIGURATION → OK → aaaa → OK → SMS MESSAGES → OK →
SYSTEM SHUTDOWN EV → OK → DISABLE → OK
Temperature fallen: OK → CONFIGURATION → OK → aaaa → OK → SMS MESSAGES → OK →
TEMP LOW EVENT → OK → DISABLE → OK
Temperature exceeded: OK → CONFIGURATION → OK → aaaa → OK → SMS MESSAGES → OK
→ TEMP HIGH EVENT → OK → DISABLE → OK
Value: aaaa – 4-digit administrator password.
Enter parameter 25, event number & parameter status value:
25 01 0 # - General alarm
25 02 0 # - System armed
25 03 0 # - System disarmed
25 04 0 # - Mains power loss
25 05 0 # - Mains power restore
25 06 0 # - Low battery
25 07 0 # - Battery failed
25 08 0 # - Periodical info
25 10 0 # - Tamper alarm
25 11 0 # - System started
25 12 0 # - Wireless signal loss
25 13 0 # - System shutdown
25 14 0 # - Temperature fallen
25 15 0 # - Temperature exceeded
Example: 25040#
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EN
87
Enable system
notification
EKB2
EKB3
Config
Tool
88
EN
Menu path:
General alarm: OK → CONFIGURATION → OK → aaaa → OK → SMS MESSAGES → OK →
ALARM EVENT → OK → ENABLE → OKK
System armed: OK → CONFIGURATION → OK → aaaa → OK → SMS MESSAGES → OK →
ARMED EVENT → OK → ENABLE → OK
System disarmed: OK → CONFIGURATION → OK → aaaa → OK → SMS MESSAGES → OK →
DISARMED EVENT → OK → ENABLE → OK
Mains power loss: OK → CONFIGURATION → OK → aaaa → OK → SMS MESSAGES → OK →
MAIN PWR LOSS EV → OK → ENABLE → OK
Mains power restore: OK → CONFIGURATION → OK → aaaa → OK → SMS MESSAGES → OK →
MAIN PWR REST EV → OK → ENABLE → OK
Low battery: OK → CONFIGURATION → OK → aaaa → OK → SMS MESSAGES → OK → LOW
BATTERY EVENT → OK → ENABLE → OK
Battery failed: OK → CONFIGURATION → OK → aaaa → OK → SMS MESSAGES → OK →
BATTERY FAIL EVENT → OK → ENABLE → OK
Periodical info: OK → CONFIGURATION → OK → aaaa → OK → SMS MESSAGES → OK →
PERIODIC SMS EV → OK → ENABLE → OK
Tamper alarm: OK → CONFIGURATION → OK → aaaa → OK → SMS MESSAGES → OK →
TAMPER EVENT → OK → ENABLE → OK
System started: OK → CONFIGURATION → OK → aaaa → OK → SMS MESSAGES → OK →
SYSTEM STARTED EV → OK → ENABLE → OK
Wireless signal loss: OK → CONFIGURATION → OK → aaaa → OK → SMS MESSAGES → OK →
WLESS SIGN LOSS EV → OK → ENABLE → OK
System shutdown: OK → CONFIGURATION → OK → aaaa → OK → SMS MESSAGES → OK →
SYSTEM SHUTDOWN EV → OK → ENABLE → OK
Temperature fallen: OK → CONFIGURATION → OK → aaaa → OK → SMS MESSAGES → OK →
TEMP LOW EVENT → OK → ENABLE → OK
Temperature exceeded: OK → CONFIGURATION → OK → aaaa → OK → SMS MESSAGES → OK
→ TEMP HIGH EVENT → OK → ENABLE → OK
Value: aaaa – 4-digit administrator password.
Enter parameter 25, event number & parameter status value:
25 01 1 # - General alarm
25 02 1 # - System armed
25 03 1 # - System disarmed
25 04 1 # - Mains power loss
25 05 1 # - Mains power restore
25 06 1 # - Low battery
25 07 1 # - Battery failed
25 08 1 # - Periodical info
25 10 1 # - Tamper alarm
25 11 1 # - System started
25 12 1 # - Wireless signal loss
25 13 1 # - System shutdown
25 14 1 # - Temperature fallen
25 15 1 # - Temperature exceeded
Example: 25061#
This operation may be carried out from the PC using the ELDES Configuration Tool software.
MANUAL ELDES ESIM264 V3.1
27.1. SMSC (Short Message Service Center) Phone Number
An SMS center (SMSC) is a GSM network element, which routes SMS text messages to the destination user and stores the SMS text message
if the recipient is unavailable. Typically, the phone number of the SMS center is already stored in the SIM card provided by the GSM operator.
If the user fails to receive replies from the system, the SMS center phone number, provided by the GSM operator, must be set manually.
Set SMSC phone
number
SMS
SMS text message content:
ssss_SMS_+ttteeellnnuumm
Value: ssss – 4-digit SMS password; ttteeellnnuumm – up to 15 digits SMSC phone number.
Example: 1111_SMS_+4417031111111
ATTENTION: Before setting the SMSC phone number, please check the credit balance of the system’s SIM card. The system will fail to reply
if the credit balance is insufficient.
MANUAL ELDES ESIM264 V3.1
EN
89
28.EVENT LOG
This feature allows to chronologically register up to 500 timestamped records regarding the following system events:
•
System start.
•
System arming/disarming.
•
Zone violated/restored.
•
Tamper violated/restored.
•
Zone bypassing.
•
Wireless device management.
•
Temperature deviation by MIN and MAX boundaries.
•
System faults.
The event log is of LIFO (last in, first out) type that allows the system to automatically replace the oldest records with the the latest ones.
View event log
EKB2
Menu path:
OK → VIEW EVENT LOG → OK → uuuu → OK
Value: uuuu - 4-digit user password.
To export the event log to .log file or clear it, please refer to the following configuration method.
Export/clear event log
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
By default, event log is enabled. To disable/enable this feature, please refer to the following configuration methods.
Disable event log
Enable event log
EKB2
Menu path:
OK → CONFIGURATION → OK → aaaa → OK → PRIMARY SETTINGS → OK → EVENT LOG → OK
→ DISABLE → OK
EKB3
Enter parameter 36 and parameter status value:
36 0 #
Example: 360#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EKB2
Menu path:
OK → CONFIGURATION → OK → aaaa → OK → PRIMARY SETTINGS → OK → EVENT LOG → OK
→ ENABLE → OK
EKB3
Config
Tool
90
EN
Enter parameter 36 and parameter status value:
36 1 #
Example: 361#
This operation may be carried out from the PC using the ELDES Configuration Tool software.
MANUAL ELDES ESIM264 V3.1
29.INDICATION OF SYSTEM FAULTS
The system comes equipped with self-diagnostic feature allowing to indicate the presence of any system fault by the keypad as well as by
SMS text message notification to the preset user phone number. By default the indication for all system faults is indicated on the keypad.
To disable/enable the indication of a certain system fault, please refer to the following configuration method.
Disable/enable
individual system fault
indication on keypad
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
NOTE: After enabling/disabling a certain system fault indication, it is necessary to restart the system by fully powering it down and powering it up again.
EKB2
Message TBL displayed in the home screen view indicates presence of system faults. In order to find out more on the particular system problem, please open menu section TROUBLES. The description on each system problem is indicated in the table
below.
Menu path:
OK → TROUBLES
Name
VIOLATED TAMPER
BATTERY FAILED
MAIN PWR FAILURE
DATE/TIME NOT SET
GSM ERROR
MANUAL ELDES ESIM264 V3.1
Description
One or more tampers are violated
Backup battery requires replacement - backup
battery resistance is 2Ω or higher
Mains power supply is lost
Date/time not set
GSM connection is lost
EN
91
Yellow LED SYSTEM indicates system faults. SYSTEM LED indications are mentioned in the table below.
EKB3
SYSTEM LED
Steady ON
Flashing
Description
One or more tampers are violated; other system faults (see below)
One or more high-numbered zones are violated
In order to find out more on the particular system fault, please enter command A provided below. After this procedure the system
will activate red zone LEDs for 15 seconds. The description on each LED indication is mentioned in the table below.
Zone LED
Description
1
One or more tampers are violated
2
Backup battery requires replacement - backup battery resistance is 2Ω or higher
3
Mains power supply is lost
4
Date/time not set.
5
One or more high-numbered zones (Z13-Z44) are violated
6
GSM connection is lost
In order to find out which particular high-numbered zone is violated please , enter command B.
In order to find out which particular tamper is violated please , enter command C.
A. System fault indication - enter command:
[CODE#]
B. Violated high-numbered zone indication – enter command:
[CODE1]
C. Violated tamper indication – enter command:
[CODE2]
The number of violated high-numbered zone or tamper can be calculated using the table below according to the formula: number
from zone LED section B + number from zone LED section A.
Example: LED #3 from section A is flashing and LED #8 from section B is illuminated continuously. According to the table below
LED #8 is equal to number 18, therefore 18 + 3 = 21.
Result: Violated high-numbered zone or tamper number is 21.
Zone LED section - A (flashing)
Zone LED 1 = 1
Zone LED 2 = 2
Zone LED 3 = 3
Zone LED 4 = 4
Zone LED 5 = 5
Zone LED 6 = 6
92
EN
Zone LED section - B (steady ON)
Zone LED 7 = 12
Zone LED 8 = 18
Zone LED 9 = 24
Zone LED 10 = 30
Zone LED 11 = 36
Zone LED 12 = 42
MANUAL ELDES ESIM264 V3.1
30.MONITORING STATION
The system can be configured to report events to the monitoring station by transmitting data messages to the monitoring station. The
system connects to the monitoring station when the MS (Monitoring Station) mode is enabled.
Enable MS mode
Disable MS mode
SMS
SMS text message content:
ssss_SCNSET:ON
Value: ssss – 4-digit SMS password.
Example: 1111_SCNSET:ON
EKB2
Menu path:
OK → CONFIGURATION → OK → aaaa → OK → MS SETTINGS → OK → MS MODE → OK →
ENABLE → OK
Value: aaaa – 4-digit administrator password
EKB3
Enter parameter 23 & parameter status value:
23 1 #
Example: 231#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
SMS
SMS text message content:
ssss_SCNSET:OFF
Value: ssss – 4-digit SMS password.
Example: 1111_SCNSET:OFF
EKB2
Menu path:
OK → CONFIGURATION → OK → aaaa → OK → MS SETTINGS → OK → MS MODE → OK →
DISABLE → OK
Value: aaaa – 4-digit administrator password
EKB3
Enter parameter 23 & parameter status value:
23 0 #
Example: 230#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
Account is a 4-digit number (By default – 9999) required to identify the alarm system unit by the monitoring station.
Set account
EKB2
EKB3
Config
Tool
Menu path:
OK → CONFIGURATION → OK → aaaa → OK → MS SETTINGS → OK → ACCOUNT → OK → cccc
→ OK
Value: aaaa – 4-digit administrator password; cccc – 4-digit account number.
Enter parameter 27 & account number:
27 cccc #
Value: cccc – 4-digit account number.
Example: 278853#
This operation may be carried out from the PC using the ELDES Configuration Tool software.
ATTENTION: The system will NOT send any data to the monitoring station while remote configuration, remote firmware update or remote
listening/2-way voice communication is in progress. However, during the remote configuration session, firmware update process or remote
listening/2-way voice communication process, the data messages will be queued up and transmitted to the monitoring station after the
remote configuration session, firmware update or remote listening/2-way voice communication process is over.
ATTENTION: Phone calls to the preset user phone number in case of alarm are disabled by force when MS mode is enabled.
MANUAL ELDES ESIM264 V3.1
EN
93
30.1.Data Messages – Events
The configuration of data messages is based on Ademco Contact ID protocol. The data messages can either be transmitted to the monitoring station alone or with duplication by SMS text message to preset user phone number. For more details on system notifications by SMS
text message, please refer to 27. SYSTEM NOTIFICATIONS.
Seq. No.
Contact ID® Code
Event
Description
1
1110
Fire alarm
Transmitted in case a zone of Fire type is violated.
2
3110
Fire restore
Transmitted in case a zone of Fire type is restored.
3
1121
Disarmed by user (Duress
password)
Transmitted in case the system is disarmed by Duress password.
4
1130
Burglary alarm
Transmitted in case a zone of Delay (if not disarmed before entry delay
countdown is completed), Interior Follower or Instant type is violated.
5
3130
Burglary restore
Transmitted in case a zone of Delay (if not disarmed before entry delay
countdown is completed), Interior Follower or Instant type is restored.
6
1133
24-Hour zone alarm
Transmitted in case of zone of 24-Hour type is violated.
7
3133
24-Hour zone restore
Transmitted in case of zone of 24-Hour type is restored.
8
1144
Tamper alarm
Transmitted in case the tamper is violated.
9
3144
Tamper restore
Transmitted in case the tamper is restored.
10
1146
Panic/Silent zone alarm
Transmitted in case of zone of Panic/Silent type is violated.
11
3146
Panic/Silent zone restore
Transmitted in case of zone of Panic/Silent type is restored.
12
1158
Temperature risen
Transmitted in case of the temperature has increased above the MAX set
value.
13
1159
Temperature fallen
Transmitted in case of temperature has decreased below the MIN set value.
14
1301
Mains power loss
Transmitted in case the main power supply is lost.
15
3301
Mains power restore
Transmitted in case the main power supply is restored.
16
1302
Low battery
Transmitted in case the backup battery voltage is 10.5V or lower / the
wireless sensor battery level runs below 5%.
17
1308
System shutdown
When the system is running on backup battery power, it transmits the data
message before the backup battery power is fully depleted.
18
1309
Battery failed
Transmitted in case the backup battery resistance is 2Ω or higher.
19
1358
GSM connection failed
Transmitted in case the GSM connection is lost.
20
1381
Wireless signal loss
Transmitted in case the connection with any wireless device is lost.
21
3381
Wireless signal restore
Transmitted in case the connection with any wireless device is restored.
22
1401
Disarmed by user
Transmitted in case the system is disarmed.
23
3401
Armed by user
Transmitted in case the system is armed.
24
1456
Disarmed in Stay mode
Transmitted in case the system is disarmed in Stay mode.
25
3456
Armed in Stay mode
Transmitted in case the system is armed in Stay mode.
26
1463
Disarmed by user (SGS
password)
Transmitted in case the system is disarmed by SGS password.
27
3463
Armed by user (SGS
password)
Transmitted in case the system is armed by SGS password.
28
1602
Test event/Kronos ping
Transmitted for system online status verification purposes.
29
3626
Date/time not set
Transmitted in case system date & time is not set.
30
1900
System started
Transmitted on system startup.
94
EN
MANUAL ELDES ESIM264 V3.1
The following table refers to user codes included in arm/disarm data messages.
Type
User Phone Number 1
User Phone Number 2
User Phone Number 3
User Phone Number 4
User Phone Number 5
iButton 1
iButton 2
iButton 3
iButton 4
iButton 5
User Password 1
User Password 2 or Arm/Disarm by Zone
User Password 3
User Password 4
User Password 5
Code
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
User Password 6
User Password 7
User Password 8
User Password 9
User Password 10
User Password 11
User Password 12
User Password 13
User Password 14
User Password 15
User Password 16
User Password 17
User Password 18
User Password 19
User Password 20
User Password 21
User Password 22
User Password 23
User Password 24
User Password 25
User Password 26
User Password 27
User Password 28
User Password 29
User Password 30
Remote Code (EGR100)
KeyFob 1
KeyFob 2
KeyFob 3
KeyFob 4
KeyFob 5
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
85
86
87
88
89
MANUAL ELDES ESIM264 V3.1
EN
95
Disable data message
EKB2
EKB3
Config
Tool
96
EN
Menu path:
General alarm/restore: OK → CONFIGURATION → OK → aaaa → OK → MS SETTINGS → OK →
DATA MESSAGES → OK → ALARM/RESTORE EV → OK → DISABLE → OK
Mains power loss/restore: OK → CONFIGURATION → OK → aaaa → OK → MS SETTINGS → OK
→ DATA MESSAGES → OK → MAIN POWER L/R EV → OK → DISABLE → OK
Armed by user: OK → CONFIGURATION → OK → aaaa → OK → MS SETTINGS → OK → DATA
MESSAGES → OK → ARMED EVENT → OK → DISABLE → OK
Disarmed by user: OK → CONFIGURATION → OK → aaaa → OK → MS SETTINGS → OK →
DATA MESSAGES → OK → DISARMED EVENT → OK → DISABLE → OK
Battery failed: OK → CONFIGURATION → OK → aaaa → OK → MS SETTINGS → OK → DATA
MESSAGES → OK → BATTERY FAIL EVENT → OK → DISABLE → OK
Test event: OK → CONFIGURATION → OK → aaaa → OK → MS SETTINGS → OK → DATA
MESSAGES → OK → TEST EVENT → OK → DISABLE → OK
System started: OK → CONFIGURATION → OK → aaaa → OK → MS SETTINGS → OK → DATA
MESSAGES → OK → SYSTEM STARTED EV → OK → DISABLE → OK
Wireless signal loss/restore: OK → CONFIGURATION → OK → aaaa → OK → MS SETTINGS →
OK → DATA MESSAGES → OK → WLESS SIGN LOSS EV → OK → DISABLE → OK
Temperature fallen: OK → CONFIGURATION → OK → aaaa → OK → MS SETTINGS → OK →
DATA MESSAGES → OK → TEMP LOW EVENT → OK → DISABLE → OK
Temperature risen: OK → CONFIGURATION → OK → aaaa → OK → MS SETTINGS → OK →
DATA MESSAGES → OK → TEMP HIGH EVENT → OK → DISABLE → OK
System shutdown: OK → CONFIGURATION → OK → aaaa → OK → MS SETTINGS → OK →
DATA MESSAGES 2 → OK → SYSTEM SHUTDOWN EV → OK → DISABLE → OK
Value: aaaa – 4-digit administrator password.
Enter parameter 24, event number & parameter status value:
24 01 0 # – General alarm/restore
24 02 0 # – Mains power loss/restore
24 03 0 # – Armed by user
24 04 0 # – Disarmed by user
24 05 0 # – Battery failed
24 06 0 # – Test event
24 07 0 # – System started
24 08 0 # – Wireless signal loss/restore
24 09 0 # – Temperature fallen
24 10 0 # – Temperature risen
24 13 0 # – System shutdown
Example: 24080#
This operation may be carried out from the PC using the ELDES Configuration Tool software.
MANUAL ELDES ESIM264 V3.1
Enable data message
EKB2
EKB3
Config
Tool
MANUAL ELDES ESIM264 V3.1
Menu path:
General alarm/restore: OK → CONFIGURATION → OK → aaaa → OK → MS SETTINGS → OK →
DATA MESSAGES → OK → ALARM/RESTORE EV → OK → ENABLE → OK
Mains power loss/restore: OK → CONFIGURATION → OK → aaaa → OK → MS SETTINGS → OK
→ DATA MESSAGES → OK → MAIN POWER L/R EV → OK → ENABLE → OK
Armed by user: OK → CONFIGURATION → OK → aaaa → OK → MS SETTINGS → OK → DATA
MESSAGES → OK → ARMED EVENT → OK → ENABLE → OK
Disarmed by user: OK → CONFIGURATION → OK → aaaa → OK → MS SETTINGS → OK →
DATA MESSAGES → OK → DISARMED EVENT → OK → ENABLE → OK
Battery failed: OK → CONFIGURATION → OK → aaaa → OK → MS SETTINGS → OK → DATA
MESSAGES → OK → BATTERY FAIL EVENT → OK → ENABLE → OK
Test event: OK → CONFIGURATION → OK → aaaa → OK → MS SETTINGS → OK → DATA
MESSAGES → OK → TEST EVENT → OK → ENABLE → OK
System started: OK → CONFIGURATION → OK → aaaa → OK → MS SETTINGS → OK → DATA
MESSAGES → OK → SYSTEM STARTED EV → OK → ENABLE → OK
Wireless signal loss/restore: OK → CONFIGURATION → OK → aaaa → OK → MS SETTINGS →
OK → DATA MESSAGES → OK → WLESS SIGN LOSS EV → OK → ENABLE → OK
Temperature fallen: OK → CONFIGURATION → OK → aaaa → OK → MS SETTINGS → OK →
DATA MESSAGES → OK → TEMP LOW EVENT → OK → ENABLE → OK
Temperature risen: OK → CONFIGURATION → OK → aaaa → OK → MS SETTINGS → OK →
DATA MESSAGES → OK → TEMP HIGH EVENT → OK → ENABLE → OK
System shutdown: OK → CONFIGURATION → OK → aaaa → OK → MS SETTINGS → OK →
DATA MESSAGES → OK → SYSTEM SHUTDOWN EV → OK → ENABLE → OK
Value: aaaa – 4-digit administrator password.
Enter parameter 24, event number & parameter status value:
24 01 1 # – General alarm/restore
24 02 1 # – Mains power loss/restore
24 03 1 # – Armed by user
24 04 1 # – Disarmed by user
24 05 1 # – Battery failed
24 06 1 # – Test event
24 07 1 # – System started
24 08 1 # – Wireless signal loss/restore
24 09 1 # – Temperature fallen
24 10 1 # – Temperature risen
24 13 1 # – System shutdown
Example: 24031#
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EN
97
30.2.Communication
The system supports the following communication methods and protocols:
• GPRS network – EGR100, Kronos protocol.
• Voice calls (GSM audio channel) – Ademco Contact ID protocol.
• RS485 data channel.
• CSD (Cricuit Switched Data).
• SMS – Cortex SMS format.
Any communication method can be set as primary or backup connection. The user can set up to 4 backup connections in any sequence order.
Initially, the system communicates via primary connection with the monitoring station. By default, if the initial attempt to transmit data is
unsuccessful, the system will make additional attempts until the data is successfully delivered. If all attempts are unsuccessful, the system
will follow this pattern:
a) The system switches to the backup connection that follows in the sequence (presumably - Backup 1).
b) The system then attempts to transmit data by the backup connection.
c) If the initial attempt is unsuccessful, the system will make additional attempts until the data is successfully delivered.
d) If the system ends up with all unsuccessful attempts, it will switch to the next backup connection in the sequence (presumably - Back­
up 2) and will continue to operate as described in the previous steps. The connection is considered unsuccessful under the following
conditions:
• GPRS network – The system has not received the ACK data message from the monitoring station within 40 seconds.
• Voice calls:
• The system has not received the “handshake” signal from the monitoring station within 40 seconds.
• The system has not received the “kissoff” signal from the monitoring station within 5 attempts each lasting 1 second.
• CSD – The system has not received the ACK data message from the monitoring station within 35 seconds.
• SMS – The system has not received the SMS delivery report from the SMSC (Short Message Service Center) within 45 seconds.
e) If one of the attempts is successful, the system will transmit all queued up data messages by this connection.
f) The system then returns to the primary connection and attempts to transmit the next data messages by primary connection.
g) If the system ends up with all unsuccessful attempts by all connections, it will wait until the Delay after last communication attempt
time (By default – 600 seconds) expires and will return to the primary connection afterwards.
h) If a new data message, except Test Event (ping), is generated during Delay after last communication attempt time, the system will
immediately attempt to transmit it to the monitoring station, regardless of Delay after last communication attempt being in progress.
98
EN
MANUAL ELDES ESIM264 V3.1
PRIMARY
Makes up to 3 or 5 attempts to transmit data
All attempts failed
Switches to BACKUP 1
Makes up to 3 or 5 attempts to transmit data
All attempts failed
One of the attempts is successful
Switches to BACKUP 2
Transmits all queued up data
Makes up to 3 or 5 attempts to transmit data
Returns to PRIMARY
All attempts failed
One of the attempts is successful
Switches to BACKUP 3
Transmits all queued up data
Makes up to 3 or 5 attempts to transmit data
Returns to PRIMARY
All attempts failed
One of the attempts is successful
Switches to BACKUP 4
Transmits all queued up data
Makes up to 3 or 5 attempts to transmit data
Returns to PRIMARY
All attempts failed
One of the attempts is successful
Waits for 600 seconds
Transmits all queued up data
Delay after last communication attempt
Returns to PRIMARY
Returns to PRIMARY
NOTE: The number of attempts, indicated in the diagram, are default and depends on the determined communication method.
MANUAL ELDES ESIM264 V3.1
EN
99
Set primary connection
EKB2
EKB3
Config
Tool
Set backup connection
1... 4
EKB2
EKB3
Menu path:
GPRS network: OK → CONFIGURATION → OK → aaaa → OK → MS SETTINGS → OK →
PRIMARY CONNECTION → OK → GPRS → OK
Voice calls: OK → CONFIGURATION → OK → aaaa → OK → MS SETTINGS → OK → PRIMARY
CONNECTION → OK → VOICE CALLS → OK
RS485: OK → CONFIGURATION → OK → aaaa → OK → MS SETTINGS → OK → PRIMARY
CONNECTION → OK → RS485 → OK
CSD: OK → CONFIGURATION → OK → aaaa → OK → MS SETTINGS → OK → PRIMARY
CONNECTION → OK → CSD → OK
SMS: OK → CONFIGURATION → OK → aaaa → OK → MS SETTINGS → OK → PRIMARY
CONNECTION → OK → SMS → OK
connection not in use: OK → CONFIGURATION → OK → aaaa → OK → MS SETTINGS → OK →
PRIMARY CONNECTION → OK → N/A → OK
Value: aaaa – 4-digit administrator password.
Enter parameter 48 & communication method number:
48 0 # – GPRS network
48 1 # – Voice calls
48 2 # – RS485
48 3 # – CSD
48 4 # – SMS
Example: 484#
This operation may be carried out from the PC using the ELDES Configuration Tool software.
Menu path:
GPRS network: OK → CONFIGURATION → OK → aaaa → OK → MS SETTINGS → OK →
BACKUP CONNECTION1... 4 → OK → GPRS → OK
Voice calls: OK → CONFIGURATION → OK → aaaa → OK → MS SETTINGS → OK → BACKUP
CONNECTION1... 4 → OK → VOICE CALLS → OK
RS485: OK → CONFIGURATION → OK → aaaa → OK → MS SETTINGS → OK → BACKUP
CONNECTION1... 4 → OK → RS485 → OK
CSD: OK → CONFIGURATION → OK → aaaa → OK → MS SETTINGS → OK →
BACKUP CONNECTION1... 4 → OK → CSD → OK
SMS: OK → CONFIGURATION → OK → aaaa → OK → MS SETTINGS → OK → BACKUP
CONNECTION1... 4 → OK → SMS → OK
connection not in use: OK → CONFIGURATION → OK → aaaa → OK → MS SETTINGS → OK →
BACKUP CONNECTION1... 4 → OK → N/A → OK
Value: aaaa – 4-digit administrator password.
Enter parameter 83, backup connection slot number & communication method
number:
83 bb 0 # – GPRS network
83 bb 1 # – Voice calls
83 bb 2 # – RS485
83 bb 3 # – CSD
83 bb 4 # – SMS
83 bb 5 # – connection not in use
Value: bb – backup connection slot number, range – [01... 05].
Example: 83031#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
If all attempts by all set connections are unsuccessful, the system will wait until the delay time (By default – 600 seconds) expires and will
attempt to transmit data to the monitoring station again starting with the primary connection.
100
EN
MANUAL ELDES ESIM264 V3.1
Set delay after last
communication
attempt
EKB2
EKB3
Config
Tool
Menu path:
OK → CONFIGURATION → OK → aaaa → OK → MS SETTINGS → OK → DELAY LAST ATTEMPT
→ OK → aaapp → OK
Value: aaaa – 4-digit administrator password; aaapp – duration of delay after last attempt,
range – [0... 65535] seconds.
Enter parameter 69 & duration of delay after last attempt:
69 aaapp #
Value: aaapp – duration of delay after last attempt, range – [0... 65535] seconds.
Example: 69200#
This operation may be carried out from the PC using the ELDES Configuration Tool software.
NOTE: 0 value disables delay after last communication attempt.
NOTE: The system is fully compatible with Kronos NET/Kronos LT monitoring station software for communication via GPRS network. When
using a different monitoring station software, EGR100 middleware is required. EGR100 is freeware and can be downloaded at www.eldes.lt/
en/download
30.2.1.GPRS Network
The system supports data transmission to the monitoring station via IP-based networks by GPRS network. The supported data formats are the
following:
• EGR100
• Kronos
To set up the system for data transmission via GPRS network, please follow the basic configuration steps:
1.
Enable MS Mode parameter (see 30. MONITORING STATION).
2.
Set 4-digit Account number (see 30. MONITORING STATION).
3.
Set server IP address, which is a public IP address of the machine running EGR100 or, Kronos monitoring station soft­ware.
4.
Set server port, which is a port of the machine running EGR100 or Kronos monitoring station software.
5.
Select TCP or UDP protocol. UDP is highly recommended for EGR100 data format.
6.
Select data format: EGR100 ir Kronos.
7.
In case EGR100 is selected, set 4-digit Unit ID number. Unit ID number can be identical to Account number.
8.
Set up APN, user name and password provided by the GSM operator. De­pending on the GSM operator, only APN might be required to set
up.
For detailed step-by-step instructions on how to establish the communication between ESIM264 alarm system and EGR100 middleware, please
refer to the middleware’s HELP file.
Set server IP address
SMS
SMS text message content:
ssss_SETGPRS:IP:add.add.add.add
Value: ssss – 4-digit SMS password; add.add.add.add – server IP address.
Example: 1111_SETGPRS:IP:65.82.119.5
EKB2
Menu path:
OK → CONFIGURATION → OK → aaaa → OK → GPRS SETTINGS → OK → SERVER IP → OK →
add.add.add.add → OK
Value: aaaa – 4-digit administartor password; add.add.add.add – server IP address.
EKB3
Config
Tool
MANUAL ELDES ESIM264 V3.1
Enter parameter 40 & server IP address:
40 add add add add #
Value: add add add add – server IP address.
Example: 40065082119005#
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EN
101
NOTE: Kronos NET/Kronos LT software communicates via TCP protocol, while EGR100 middle-ware v1.2 and up supports both – TCP and
UDP protocols. However, TCP protocol is NOT recommend to use with EGR100.
Set protocol
Set DNS1 server IP
address
Set DNS2 server IP
address
Set data format as
Kronos or EGR100
102
EN
SMS
SMS text message content:
ssss_SETGPRS:PROTOCOL:ptc
Value: ssss – 4-digit SMS password; ptc – protocol, range – [TCP... UDP].
Example: 1111_SETGPRS:PROTOCOL:UDP
EKB2
Menu path:
OK → CONFIGURATION → OK → aaaa → OK → GPRS SETTINGS → OK → PROTOCOL → OK →
TCP | UDP → OK
Value: aaaa – 4-digit administartor password.
EKB3
Enter parameter 43 & protocol number:
43 0 # - TCP
43 1 # - UDP
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EKB2
Menu path:
OK → CONFIGURATION → OK → aaaa → OK → GPRS SETTINGS → OK → DNS1 → OK → add.
add.add. add → OK
Value: aaaa – 4-digit administartor password; add.add.add.add – DNS1 server IP address.
EKB3
Enter parameter 41 & DNS1 server IP address:
41 add add add add #
Value: add add add add – DNS1 server IP address.
Example: 41065082119001#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EKB2
Menu path:
OK → CONFIGURATION → OK → aaaa → OK → GPRS SETTINGS → OK → DNS2 → OK → add.
add.add. add → OK
Value: aaaa – 4-digit administartor password; add.add.add.add – DNS2 server IP address.
EKB3
Enter parameter 42 & DNS2 server IP address:
42 add add add add #
Value: add add add add – DNS2 server IP address.
Example: 42065082119002#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
MANUAL ELDES ESIM264 V3.1
Set APN
SMS
Config
Tool
Set user name
SMS
Config
Tool
Set password
SMS
Config
Tool
SMS text message content:
ssss_SETGPRS:APN:acc-point-name
Value: ssss – 4-digit SMS password; acc-point-name – up to 31 character APN (Access Point
Name) provided by the GSM operator.
Example: 1111_SETGPRS:APN:internet
This operation may be carried out from the PC using the ELDES Configuration Tool software.
SMS text message content:
ssss_SETGPRS:USER:usr-name
Value: ssss – 4-digit SMS password; usr-name – up to 31 character user name provided by
the GSM operator.
Example: 1111_USER:mobileusr
This operation may be carried out from the PC using the ELDES Configuration Tool software.
SMS text message content:
ssss_SETGPRS:PSW:password
Value: ssss – 4-digit SMS password; password – up to 31 character password provided by
the GSM operator.
Example: 1111_SETGPRS:PSW:mobilepsw
This operation may be carried out from the PC using the ELDES Configuration Tool software.
By default, if the initial attempt to transmit data to the monitoring station via GPRS network method is unsuccessful, the system will make
up to 2 additional attempts. If all attempts are unsuccessful, the system will switch to next backup connection that follows in the sequence
and will attempt to transmit data until it is successfully delivered to the monitoring station.
Set attempts
EKB2
EKB3
Config
Tool
Menu path:
OK → CONFIGURATION → OK → aaaa → OK → MS SETTINGS → OK → GPRS SETTINGS → OK
→ GPRS ATTEMPTS → OK → att → OK
Value: aaaa – 4-digit administrator password; att – number of attempts, range – [1... 255].
Enter parameter 68 & number of attempts:
68 att #
Value: att – number of attempts, range – [01... 255].
Example: 6809#
This operation may be carried out from the PC using the ELDES Configuration Tool software.
To report the online status, the system periodically transmits (By default – every 180 seconds) Test Event data message (ping) to the
monitoring station via GPRS network.
MANUAL ELDES ESIM264 V3.1
EN
103
Set test period
EKB2
EKB3
Config
Tool
Menu path:
OK → CONFIGURATION → OK → aaaa → OK → MS SETTINGS → OK → GPRS SETTINGS → OK
→ TEST PERIOD → OK → tteessttpp → OK
Value: aaaa – 4-digit administrator password; tteessttpp – test period, range – [0... 65535]
seconds.
Enter parameter 46 & number of attempts:
46 tteessttpp #
Value: tteessttpp – test period, range – [0... 65535] seconds.
Example: 46120#
This operation may be carried out from the PC using the ELDES Configuration Tool software.
NOTE: 0 value disables test period.
Unit ID is a 4-digit number (By default – 0000) required to identify the alarm system unit by EGR100 middle-ware. It is MANDATORY to
change the default Unit ID before using EGR100.
Set unit ID
EKB2
EKB3
Config
Tool
View GPRS network
settings
SMS
Config
Tool
Menu path:
OK → CONFIGURATION → OK → aaaa → OK → MS SETTINGS → OK → GPRS SETTINGS → OK
→ UNIT ID → OK → unid → OK
Value: aaaa – 4-digit administartor password; unid – 4-digit unit ID number.
Enter parameter 47 & unit ID number:
47 unid #
Value: unid – 4-digit unit ID number.
Example: 472245#
This operation may be carried out from the PC using the ELDES Configuration Tool software.
SMS text message content:
ssss_SETGPRS?
Example: 1111_SETGPRS?
This operation may be carried out from the PC using the ELDES Configuration Tool software.
NOTE: Kronos NET/Kronos LT software communicates via TCP protocol, while EGR100 middle-ware v1.2 and up supports both – TCP and
UDP protocols. However, TCP protocol is NOT recommend to use with EGR100.
ATTENTION: It is necessary to restart the system locally by powering down and powering up the system the system or remotely (see 33.
REMOTE SYSTEM RESTART) after changing the IP address or switching from TCP to UDP.
104
EN
MANUAL ELDES ESIM264 V3.1
30.2.2.Voice Calls and SMS
The system supports up to 3 monitoring station phone numbers for communication with the alarm system by Voice Calls or SMS commu­
nication method. Tel. Number 1 is mandatory, the other two can be used as backup phone numbers and are not necessary. The supported
phone number format is the following:
• International (w/o plus) – The phone numbers must be entered starting with an international country code in the following format:
[international code][area code][local number], example for UK: 4417091111111.
To set up the system for data transmission via Voice Calls or SMS, please follow the basic configuration steps:
1. Enable MS Mode parameter (see 30. MONITORING STATION).
2. Set 4-digit Account number (see 30. MONITORING STATION).
3. Set Tel. Number 1... 3.
Set monitoring station
phone number
EKB2
EKB3
Delete monitoring
station phone number
Menu path:
OK → CONFIGURATION → OK → aaaa → OK → MS SETTINGS → OK → VOICE CALLS/SMS ST →
OK → TEL. NUMBER 1... 3 → OK → ttteeellnnuumm → OK
Value: aaaa – 4-digit administrator password; ttteeellnnuumm – up to 15 digits monitoring
station phone number.
Enter parameter 26, phone number slot & phone number:
26 ps ttteeellnnuumm #
Value: ps – phone number slot, range – [01... 03]; ttteeellnnuumm – up to 15 digits monitoring station phone number.
Example: 26014417091111111#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EKB2
Menu path:
OK → CONFIGURATION → OK → aaaa → OK → MS SETTINGS → OK → VOICE CALLS/SMS ST →
OK → TEL. NUMBER 1... 3 → OK → OK
Value: aaaa – 4-digit administrator password.
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
By default, if the initial attempt to transmit data to the monitoring station’s Tel Number 1 via Voice Calls or SMS method is unsuccessful, the
system will make up to 4 additional attempts. After all unsuccessful attempts, the system will continue to communicate with the monitoring station by switching to the next phone number that follows in the sequence and making up to 4 additional attempts if the initial attempt is unsuccessful. If all attempts to all phone numbers are unsuccessful, the system will switch to next backup connection that follows
in the sequence and will attempt to transmit data until it is successfully delivered to the monitoring station.
Set attempts
MANUAL ELDES ESIM264 V3.1
EKB2
Menu path:
OK → CONFIGURATION → OK → aaaa → OK → MS SETTINGS → OK → VOICE CALLS/SMS ST →
OK → ATTEMPTS → OK → at → OK
Value: aaaa – 4-digit administrator password; at – number of attempts, range – [1... 10].
EKB3
Enter parameter 37 & number of attempts:
37 at #
Value: at – number of attempts, range – [01... 10].
Example: 3706#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EN
105
Due to the individual configuration of each monitoring station, the system may fail to deliver the data message via Voice Calls communication method. In such cases it is recommended to adjust the microphone gain until the optimal value, leading to successful data message
delivery, is discovered.
Set microphone gain
EKB2
Menu path:
OK → CONFIGURATION → OK → aaaa → OK → PRIMARY SETT INGS → OK → GSM AUDIO → OK
→ MICROPHONE GAIN → OK → mg → OK
Value: aaaa – 4-digit administrator password; mg – microphone gain, range – [0... 15].
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
30.2.3.CSD
The system supports up to 5 monitoring station phone numbers for communication with the alarm system by CSD communication method.
Tel. Number 1 is mandatory, the other four can be used as backup phone numbers and are not necessary. The supported phone number
format is the following:
• International (w/o plus) – The phone numbers must be entered starting with an international country code in the following format:
[international code][area code][local number], example for UK: 4417091111111.
To set up the system for data transmission via CSD, please follow the basic configuration steps:
1. Enable MS Mode parameter (see 30. MONITORING STATION).
2. Set 4-digit Account number (see 30. MONITORING STATION).
3. Set Tel. Number 1... 5.
Set monitoring station
phone number
EKB2
EKB3
Delete monitoring
station phone number
106
EN
Menu path:
OK → CONFIGURATION → OK → aaaa → OK → MS SETTINGS → OK → CSD SETTINGS → OK →
TEL. NUMBER 1... 5 → OK → ttteeellnnuumm → OK
Value: aaaa – 4-digit administrator password; ttteeellnnuumm – up to 15 digits monitoring
station phone number.
Enter parameter 85, number of entry & phone number:
85 ps ttteeellnnuumm #
Value: ps – phone number slot, range – [01... 05]; ttteeellnnuumm – up to 15 digits monitoring station phone number.
Example: 85014417091111111#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EKB2
Menu path:
OK → CONFIGURATION → OK → aaaa → OK → MS SETTINGS → OK → CSD SETTINGS → OK →
TEL. NUMBER 1... 5 → OK → OK
Value: aaaa – 4-digit administrator password.
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
MANUAL ELDES ESIM264 V3.1
By default, if the initial attempt to transmit data to the monitoring station’s phone number via CSD method is unsuccessful, the system will
make up to 4 additional attempts. If all attempts are unsuccessful, the system will switch to next backup connection that follows in the
sequence and will attempt to transmit data until it is successfully delivered to the monitoring station.
Set attempts
EKB2
EKB3
Config
Tool
MANUAL ELDES ESIM264 V3.1
Menu path:
OK → CONFIGURATION → OK → aaaa → OK → MS SETTINGS → OK → CSD SETTINGS → OK →
TEL. NUMBER 1... 5 → OK → OK
Value: aaaa – 4-digit administrator password; at – number of attempts, range – [1... 10].
Enter parameter 84 & number of attempts:
84 at #
Value: at – number of attempts, range – [01... 10].
Example: 8403#
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EN
107
31.ELDES WIRED DEVICES
31.1. RS485 Interface
RS485 interface is used for the system to communicate with the following devices:
•
EKB2 keypads (up to 4 units).
•
EKB3 keypads (up to 4 units).
•
EPGM1 modules (1 unit).
The terminals of RS485 interface are Y (yellow wire) and G (green wire), which are clock and data respectively. The devices, connected to
RS485 interface, must be powered from the AUX+ and AUX- terminals.
For more details on RS485 device wiring, please refer to 3.2.7. RS485.
31.1.1. EKB2 - LCD Keypad
EKB2 is an LCD keypad intended for using with ESIM264 alarm system.
Main EKB2 features:
•
Alarm system arming and disarming (see 12.3. EKB2 Keypad and User Password).
•
Arming and disarming in Stay mode (see 15. STAY MODE).
•
System parameter configuration (see 5. CONFIGURATION METHODS).
•
PGM output control (see 18.4. Turning PGM Outputs ON and OFF).
•
System information display (see 31.1.1.4. Visual and Audio Indications).
•
Audio indication by built-in buzzer (see 31.1.1.4. Visual and Audio Indications ).
•
Wireless device information display (see 19.2. Wireless Device Information and Signal Status Monitoring).
•
Keypad partition switch (see 23.3. Keypad Partition and Keypad Partition Switch).
•
Temperature display (see 31.1.1.1.2 Keys Functionality).
•
Time display (see 31.1.1.1.2 Keys Functionality).
The system configuration is performed by accessing EKB2 menu and entering the required values. ESIM264 system allows to connect up
to 4 EKB2 keypads.
31.1.1.1. Technical Specifications
31.1.1.1.1 Electrical & Mechanical Characteristics
Power Supply
12-14V
Maximum Keypad Connection Cable Length
100 m.
Dimensions
133 x 89 x 19 mm
Humidity
0-90% RH @ 0... +40 °C (non-condensing)
Range of Operating Temperatures
0...+55ºC
108
EN
150mA max.
MANUAL ELDES ESIM264 V3.1
31.1.1.1.2 Keys Functionality
One menu level back / cancel
Temperature
38
Menu navigation – up
GSM signal
strength
Digital
clock
20,2 C
0
Menu navigation – down
Confirm (enter) value
...
Value typing
Keypad partition switch / minus
System
status
message
STAY
BYP
TBL
00:45
Home screen
view
READY
GARAGE
One or more
violated
zones are
bypassed
One or
more
system
faults are
present
System
armed in Stay
mode
symbol for entering negative
temp. value
Additional menu / minus symbol
for entering negative temp. value
Custom
partition
name
31.1.1.1.3 Connector and Main Unit Functionality
Vin
Positive power supply terminal
COM
Negative power supply terminal
G
RS485 interface for communication (green wire)
Y
RS485 interface for communication (yellow wire)
COM
Common terminal for Z1
Z1
Security zone terminal
A0
Keypad address pin
A1
Keypad address pin
Buzzer
Buzzer for audio indications
Tamper
Tamper-button for EKB2 enclosure status monitoring
39
VIN
COM
Z1
G
Y
COM
A0A1
Buzzer
Tamper
31.1.1.1.4 Keypad Address
A0 and A1 pins located on the back side of the keypad are intended to set keypad address. The keypad address is set by putting the jumper
(-s) on the pins. ESIM264 system allows to connect up to 4 EKB2 keypads - each set under different address. Jumper combinations for different keypad address configuration are indicated in the table below.
MANUAL ELDES ESIM264 V3.1
EN
109
Keypad 2
Jumper position
Address
A0
A1
Keypad 1
Keypad 3
A0
A1
A0
A1
Address
A0
A1
Jumper position
Keypad 4
The address of each connected keypad is also indicated in ELDES Configuration Tool software.
31.1.1.2. Installation
1. Remove the screw located on the bottom side of the enclosure (see Fig. No.
40)
40
2. Detach keypad holder from EKB2 keypad by gently pulling the holder
towards yourself (see Fig. No. 41).
3. Fix the keypad holder on the wall using the screws. (see Fig. No. 42)
4. Disconnect ESIM264 main power supply and backup battery.
5. Wire up keypad terminals to ESIM264 alarm system respectively – Vin to
AUX+, COM to AUX-, Y to Y, G to G (see Fig. No. 43).
6. Connect a sensor and the resistor across Z1 and COM terminalss in accor­
dance with zone connection Type 1 or Type 2 (see 2.3.2. Zone Connec­
tion Types). As keypad zone Z1 is disabled by default, it can be enabled
by SMS, ELDES Configuration Tool, EKB2 and EKB3 keypad. Keypad zone Z1
must be enabled and resistor connected even if the tamper button alone is
required (see Fig. No. 43).
41
NOTE: Keypad zone connection type can differ from selected on-board
zone connection type.
NOTE: ATZ mode is NOT supported by keypad zones. ATZ mode is
ineffective for keypad zones when enabled.
7. Set the keypad address by putting the jumper on A0 and A1 pins (see
32.1.1.1.4 Keypad Address).
8. Fix the keypad into the holder.
ATTENTION: Before fixing the keypad into the holder please , make
sure that the tamper button is properly pressed (see Fig. No. 39).
9. Screw in the bottom side of the enclosure. (see Fig. No. 40).
10. Power up ESIM264 alarm system.
11. EKB2 keypad is ready.
For more details on multiple keypad wiring, please refer to 3.2.7. RS485
110
EN
MANUAL ELDES ESIM264 V3.1
42
43
ESIM264
Y G
VIN
COM
Z1
AUX- AUX+
EKB2
G
Y
COM
5,6kΩ
31.1.1.3. Visual and Audio Indications
EKB2 can be used even in dark premises as the LCD screen and keys are illuminated continuously. The illumination level lowers down if 3 minutes after the last key-touch expires while the system is disarmed. In case of alarm, the keypad illumination level is boosted and stays in this
state until the system is disarmed.
The built-in buzzer uses two types of sound signals – three short beeps and one long beep. Three short beeps stand for successfully carried
out configuration, one long beep – for invalid configuration. In addition, the buzzer emits short beeps in case of alarm and exit/entry delay
countdown.
31.1.1.4. EKB2 Zone and Tamper
Keypad EKB2 has one wired zone Z1 and one tamper button. By default, the keypad zone Z1 is disabled. The keypad zone can be enabled by
SMS, EKB2 keypad, EKB3 keypad and ELDES Configuration Tool software (see 14.9. Disabling and Enabling Zones). When Z1 is enabled,
it operates like any other system zone, therefore a sensor can be connected to it. In addition, Z1 and COM terminals must be connected with
resistor of 5,6kΩ nominal.
The tamper button is intended for monitoring the enclosure status of EKB2, therefore the system causes alarm if the enclosure is illegally
opened. Keypad zone Z1 must be enabled and resistor connected even if the tamper button alone is required.
31.1.1.5. Icons and Messages
Icon / Message
Description
Chime - Delay zone violated when system
is disarmed.
Exit delay countdown initiated.
System is armed and menu is locked.
System is disarmed and menu is unlocked
Icon / Message
24H zone violated.
FIRE ALARM
Fire zone violated.
TAMPER ALARM
READY
NOT READY
ARMED
+ CONFIGURATION
MODE
BURGLARY ALARM
Configuration mode activated.
Delay, Instant or Follow zone violated
when system is armed.
MANUAL ELDES ESIM264 V3.1
Description
24 ALARM
Tamper violated
System is ready to be armed.
System is not ready to be armed – one or
more zones / tampers violated.
System is armed (optional feature).
STAY
Stay mode activated
BYP
System armed in Stay mode
TBL
One or more system faults are present
EN
111
31.1.1.6. Menu Tree
HOME SCREEN VIEW
P1
P2
[1] part-name...
[4] part-name
OK
ENTER STAY
uuuu
BYPASS
FAULTS
DATE/TIME SETTINGS
BYPASS LIST 2
VIEW EVENT LOG
UNBYPASS | BYPASS
Z13-zone-name...
Z44-zone-name
VIOLATED TAMPER | BATTERY FAILED | MAIN PWR FAILURE
| DATE/TIME NOT SET | GSM ERROR
BYPASS LIST 1
UNBYPASS | BYPASS
Z13-zone-name...
Z44-zone-name
TAMPER 1... 44
VIOLATED TAMPERS
BYP VIOLATED ZONES
Z1-zone-name...
Z12-zone-name
ZONE 1... 44
VIOLATED ZONES
yyyy-mm-dd hr:mn
uuuu
ENTER USER PSW
CONFIGURATION
BYPASS LIST 3
aaaa
PHONE NUMBER
ttteeellnnuumm
ENTER ADMIN PSW
PARTITION
UNBYPASS | BYPASS
pv
PRIMARY SETTINGS
SEND ARM/DARM SMS
CALL/SMS SETTINGS
USERS
WIRELESS DEVICES
wless-dev wless-id
BATTERY
DISABLE | ENABLE
USER 1... 5
SEND ARM/DARM ALL
DISABLE | ENABLE
SEND ALARM SMS ALL
DISABLE | ENABLE
CALL IN CASE ALARM
DISABLE | ENABLE
CTRL FROM ANY NUM
DISABLE | ENABLE
SIGNAL
PASSWORDS
ERROR RATE
SMS PASSWORD
FW RELEASE
IBUTTON KEYS
DISABLE | ENABLE
NEW IBUTTON
IBUTTON 1... 5
[0001... 9999]
ADMIN PASSWORD
[0000... 9999]
[0000... 9999]
USER PASSWORDS
PASSWORD
USER PASSWORD 1... 16
PARTITION
ID
PARTITION0 | PARTITION1
PARTITION
USER PASSWORD 17... 30
REMOVE
DURESS PASSWORD
SGS PASSWORD
PARTITION0 |
PARTITION1
PASSWORD
[0000... 9999]
PARTITION
PARTITION0 |
PARTITION1
N/A | 1... 10
N/A | 1... 10
REMOVE PASSWORD
[0000... 9999]
Continued in next page
112
EN
MANUAL ELDES ESIM264 V3.1
NAME
DISABLE |
ENABLE
seconds
ZONE 1... 12
STATUS
TYPE
[1... 65535]
ENTRY DELAY
WIRELESS ZONE 1... 16
ONBOARD ZONES
INTERIOR FOLLOWER | INSTANT | 24HOUR | DELAY | FIRE
| PANIC/SILENT
WIRELESS ZONES
NAME
DISABLE | ENABLE
INTERIOR FOLLOWER | INSTANT |
24-HOUR | DELAY | FIRE | PANIC/SILENT
[1... 65535]
ENTRY DELAY
STAY
SMS LANGUAGE
INFO SMS SCHEDULER
FREQUENCY (DAYS)
TIME
EVENT LOG
[-55... +125] 0C
TEMP. MAX
[-55... +125] 0C
seconds
PARTITION0 | PARTITION1
DISABLE | ENABLE
KEYPAD 1... 4 ZONE
[0... 600]
BELL SQUAWK
EWS2 LED
INTERIOR FOLLOWER | INSTANT |
24-HOUR | DELAY | FIRE | PANIC/SILENT
[1... 65535]
ENTRY DELAY
seconds
LOSS DELAY
[0... 65535]
PARTITION SWITCH
seconds
DISABLE | ENABLE
KEYPAD PARTITION
EPGM1 ZONES
NAME
KEYPAD 1... 4
PARTITION0
| PARTITION1
DISABLE | ENABLE
STATUS
INTERIOR FOLLOWER | INSTANT |
24-HOUR | DELAY | FIRE | PANIC/SILENT
[1... 65535]
ENTRY DELAY
seconds
GSM AUDIO
DISABLE | ENABLE
MICROPHONE GAIN
TAMPER NAME
PARTITION
FORCE
seconds
KEYPAD PARTITION
DISABLE | ENABLE
EPGM1 ZONE 1... 16
DISABLE | ENABLE
[0... 65535]
RESTORE DELAY
PARTITION0 | PARTITION1
DISABLE | ENABLE
DISABLE | ENABLE
MAIN POWER STATUS
DISABLE | ENABLE
PARTITION
minutes
DISABLE | ENABLE
EWF1 SIREN INTERC.
TAMPER NAME
STAY
[1... 10]
SRN IF WLESS LOSS
DISABLE | ENABLE
STATUS
TYPE
seconds
SIREN SETTINGS
ALARM DURATION
KEYPAD ZONES
NAME
FORCE
[0... 23]
DISABLE | ENABLE
TEMP. MIN
EXIT DELAY
STAY
[0... 99]
DISABLE | ENABLE
PARTITION
TYPE
yyyy-mm-dd hr:mn
DATE/TIME SETTINGS
TAMPER NAME
FORCE
ENGLISH | second-lang
TEMPERATURE SENSOR
STATUS
TYPE
PRIMARY SETTINGS
ZONES
CONFIGURATION
Continued from previous page
PARTITION0 | PARTITION1
SPEAKER LEVEL
[0... 15]
[0... 100]
DISABLE | ENABLE
Continued in next page
MANUAL ELDES ESIM264 V3.1
EN
113
ATZ MODE
CONFIGURATION
DISABLE | ENABLE
ZONES
Continued from previous page
MS SETTINGS
ACCOUNT
TYPE 1... 3
ZONE TYPE:6-ZONE M
TYPE 4... 5
ZONE TYPE:ATZ MODE
MS MODE
N/A / ZONE 1... 12
ARM/DISARM BY ZONE
DATA MESSAGES
DISABLE | ENABLE
DELAY LAST ATTEMPT
[1... 65535]
DISABLE | ENABLE
ALARM/RESTORE EV
DISABLE | ENABLE
CHIME
MAIN POWER L/R EV
PGM OUTPUTS
DISABLE | ENABLE
USING EPGM8
STATUS
DISARMED EVENT
BATTERY FAIL EVENT
DISABLE | ENABLE
TEST EVENT
OUTPUT 1... 12
DISABLE | ENABLE
ARMED EVENT
DISABLE | ENABLE
DISABLE | ENABLE
DISABLE | ENABLE
ONBOARD OUTPUTS
SYSTEM STARTED EV
DISABLE | ENABLE
DISABLE | ENABLE
WLESS SIGN LOSS EV
NAME
TEMP LOW EVENT
DISABLE | ENABLE
DISABLE | ENABLE
TEMP HIGH EVENT
wless-dev wless-id
BATTERY
SIGNAL
WIRELESS DEVICES
ERROR RATE
FW RELEASE
GPRS SETTINGS
[0.0.0.0]
SERVER IP
[0.0.0.0]
DNS1
APN
[0.0.0.0]
DNS2
USER
TCP | UDP
[1... 65535]
PROTOCOL
SERVER PORT
[1... 65535]
SYSTEM SHUTDOWN EV
DISABLE | ENABLE
DISABLE | ENABLE
VOICE CALLS/SMS ST
ATTEMPTS
LOCAL PORT
seconds
[1... 10]
TEL. NUMBER1
ttteeellnnuumm
15 digits
TEL. NUMBER2
ttteeellnnuumm
15 digits
TEL. NUMBER3
ttteeellnnuumm
15 digits
PASSWORD
PROFILE
Continued in next page
114
EN
MANUAL ELDES ESIM264 V3.1
MS SETTINGS
SMS MESSAGES
CONFIGURATION
Continued from previous page
CSD SETTINGS
[1... 10]
ATTEMPTS
DISABLE | ENABLE
ALARM EVENT
DISABLE | ENABLE
ARMED EVENT
TEL. NUMBER1
ttteeellnnuumm
15 digits
DISARMED EVENT
TEL. NUMBER2
ttteeellnnuumm
15 digits
TEL. NUMBER3
ttteeellnnuumm
15 digits
MAIN PWR REST EV
TEL. NUMBER4
ttteeellnnuumm
15 digits
PERIODIC SMS EV
TEL. NUMBER5
ttteeellnnuumm
15 digits
DISABLE | ENABLE
DISABLE | ENABLE
MAIN PWR LOSS EV
DISABLE | ENABLE
DISABLE | ENABLE
DISABLE | ENABLE
DISABLE | ENABLE
DISABLE | ENABLE
DISABLE | ENABLE
TAMPER EVENT
SYSTEM STARTED EV
GPRS SETTINGS
GPRS ATTEMPTS
[0... 255]
WLESS SIGN LOSS EV
SYSTEM SHUTDOWN EV
DISABLE | ENABLE
TEMP LOW EVENT
DISABLE | ENABLE
TEMP HIGH EVENT
UNIT ID
[0000... 9999]
TEST PERIOD
[0... 65535]
seconds
PRIMARY CONNECTION
GPRS | VOICE CALLS | RS485 | CSD | SMS | N/A
ENTER USER PSW
uuuu
RESET TO DEFAULT
BACKUP CONNECTION1
GPRS | VOICE CALLS | RS485 | CSD | SMS | N/A
BACKUP CONNECTION2
GPRS | VOICE CALLS | RS485 | CSD | SMS | N/A
BACKUP CONNECTION3
GPRS | VOICE CALLS | RS485 | CSD | SMS | N/A
BACKUP CONNECTION4
GPRS | VOICE CALLS | RS485 | CSD | SMS | N/A
MANUAL ELDES ESIM264 V3.1
EN
115
31.1.2. EKB3 - LED Keypad
EKB3 is a LED keypad intended for using with ESIM264 alarm system.
Main EKB3 features:
•
Alarm system arming and disarming (see 12.4. EKB3 Keypad and User Password).
•
•
•
•
•
•
Arming and disarming in Stay mode (see 15. STAY MODE).
System parameter configuration (see 5. CONFIGURATION METHODS).
PGM output control (see 18.4. Turning PGM Outputs ON and OFF).
Visual indication by LED indicators (see 31.1.2.3. Visual and Audio Indications).
Audio indication by built-in buzzer (see 31.1.2.3. Visual and Audio Indications).
Keypad partition switch (see 23.3. Keypad Partition and Keypad Partition Switch).
The system configuration by EKB3 keypad is performed by activating the Configuration mode (see 5. CONFIGURATION METHODS) and entering the required parameters & values. ESIM264 system allows to connect up to 4 EKB3 keypads.
31.1.2.1. Technical Specifications
31.1.2.1.1 Electrical & Mechanical Characteristics
Power Supply
12-14V
Maximum Keypad Connection Cable Length
100 m.
150mA max
Dimensions
140x100x18mm
Humidity
0-90% RH @ 0... +40 °C (non-condensing)
Range of Operating Temperatures
-30...+55ºC
31.1.2.1.2 LED Functionality
ARMED
Steady ON - alarm system is armed / exit delay in progress; flashing - Configuration mode activated
READY
Steady ON - system is ready – no violated zones and tampers
SYSTEM
Steady ON - system faults; flashing - violated high-numbered zone (Z13-Z44)
BYPS
Steady ON - zone bypass mode
1-12
Steady ON - violated zone Z1... Z12
31.1.2.1.3 Keys Functionality
[BYPS]
Zone bypass mode
[CODE]
System fault list / violated high-numbered zone indication / violated tamper indication
[*]
1st character for Configuration mode activation/deactivation command / clear typed in characters / keypad partition switch (if enabled)
[#]
Confirm (enter) command
[0] ... [9]
Command typing
[STAY]
Manual system arming in Stay mode
[INST]
N/A
31.1.2.1.4 Connector Functionality
AUX+
Positive power supply terminal
AUX-
Negative power supply terminal
G
RS485 interface for communication (green wire)
Y
RS485 interface for communication (yellow wire)
COM
Common terminal for Z1
Z1
Security zone terminal
Z2
N/A
3, 2
Keypad address pins
1
N/A
116
EN
MANUAL ELDES ESIM264 V3.1
BACK SIDE
FRONT SIDE
44
A
B
ARMED
READY
SYSTEM
1
BYPS
7
8
2
9
3
4
10
11
5
12
6
1
2
3
STAY
4
5
6
BYPS
7
8
9
INST
*
0
#
CODE
3 2 1
TAMPER
COM Y AUXZ2 Z1
G AUX+
31.1.2.1.5 Keypad Address
Pins 3 and 2 located on the back side of the keypad are intended to set keypad address. The keypad address is set by putting the jumper (-s)
on the pins. ESIM264 system allows to connect up to 4 EKB3 keypads - each set under different address. Jumper combinations for different
keypad address configuration are indicated in the table below.
Address Configuration
Jumper position
3 2
Address
1
Keypad 1
3 2
1
Keypad 2
3 2
1
Keypad 3
3 2
1
Keypad 4
NOTE: Pins 1 are inactive.
The address of each connected keypad is also indicated in ELDES Configuration Tool software.
31.1.2.2. Installation
1. Detach keypad holder from EKB3 keypad . Keypad holder detach points are marked with arrows (see Fig. No. 45).
45
DOWN SIDE
BACK SIDE
MANUAL ELDES ESIM264 V3.1
EN
117
2. Disconnect alarm system ESIM264 power supply and backup battery before connecting the wires.
46
ESIM264
Y G
AUX- AUX+
EKB3
COM Y AUXZ2 Z1
G AUX+
5,6kΩ
3. Wire up keypad terminals to ESIM264 alarm system respectively – AUX+ to AUX+, AUX- to AUX-, Y to Y, G to G. (see Fig. No. 46).
4. Connect a sensor and the resistor across Z1 and COM terminalss in accordance with zone connection Type 1 or Type 2 (see 2.3.2. Zone
Connection Types). As keypad zone Z1 is disabled by default, it can be enabled by SMS, ELDES Configuration Tool, EKB2 and EKB3 keypad. Z2 terminal is permanently inactive. Keypad zone Z1 must be enabled and resistor connected even if the tamper button alone is
required (see Fig. No. 44).
NOTE: Keypad zone connection type can differ from selected on-board zone connection type.
NOTE: ATZ mode is NOT supported by keypad zones. ATZ mode is ineffective for keypad zones when enabled.
5. Set the keypad address by combining DIP switch positions (see 31.1.2.1.5 Keypad Address).
6. Infix the keypad into the holder (see Fig. No. 45).
ATTENTION: Before fixing the keypad into the holder please , make sure that the tamper is properly pressed (see Fig. No. 44).
7. Power up ESIM264 alarm system.
8. EKB3 keypad is ready.
For more details on multiple keypad wiring, please refer to 3.2.7. RS485.
31.1.2.3. Visual and Audio Indications
EKB3 keys have a LED back-light, therefore it is possible to use this keypad even in dark premises. The back-light lasts for 3 minutes after the
last key-stroke while the system is disarmed. In case of alarm, the keypad back-light turns ON and lasts until the system is disarmed.
The built-in buzzer uses two types of sound signals – three short beeps and one long beep. Three short beeps stand for successfully carried
out configuration command, one long beep – for invalid configuration command. In addition, the buzzer emits short beeps in case of alarm and
exit/entry delay countdown.
31.1.2.4. EKB3 Zone & Tamper
Keypad EKB3 has one wired zone Z1 and one tamper button. By default, the keypad zone Z1 is disabled. The keypad zone can be enabled by
SMS, EKB2 keypad, EKB3 keypad, EKB3W keypad and ELDES Configuration Tool software (see 14.9. Disabling and Enabling Zones). Zone
Z1 is enabled, it operates like any other system zone, therefore a sensor can be connected to it. In addition, Z1 and COM terminals must be
connected with resistor of 5,6kΩ nominal.
The tamper button is intended for monitoring the enclosure status of EKB3, therefore the system causes alarm if the enclosure is illegally
opened. Keypad zone Z1 must be enabled and resistor connected even if the tamper button alone is required.
118
EN
MANUAL ELDES ESIM264 V3.1
31.1.3. EPGM1 - Hardwired Zone & PGM Output Expansion Module
EPGM1 is a hardwired zone & PGM output expansion module intended for using with ELDES alarm systems.
Main EPGM1 features:
• hardwired zone expansion adding 16 additional zones
• 2 PGM output expansion for electrical appliance connection
31.1.3.1. Technical Specifications
31.1.3.1.1 Electrical & Mechanical Characteristics
Power Supply
Number of Digital Inputs
Nominal Resistance
Number of PGM Outputs
Maximum PGM Output Current
EPGM1 PGM Output Circuit
10-24V
16
5,6kΩ
2
250 mA
100mA max without auxiliary equipment.
Maximum Commuting PGM Output Values
AUX: Auxiliary Equipment Power Supply
Dimensions
Humidity
Voltage – 30V; current 250mA
13,8V
500 mA max
118 x 47 mm
Range of Operating Temperatures
-20...+55ºC
1R
OUT
Open collector output.
Output is pulled to
COM when turned on.
0-90% RH @ 0... +40 °C (non-condensing)
31.1.3.1.2 LED and Pin Functionality
C2, C1
Z1 - Z16
STATUS
PGM output C1, C2 status – on/off
Zone Z1 - Z16 state – alarm/restore
EPGM1 micro-controller status
31.1.3.1.3 Connector Functionality
C1, C2
Z1 - Z16
AUXAUX+
Y
G
COM
DC+
PGM output terminals
Security zone terminals
Negative power supply terminal for auxiliary equipment
Positive power supply terminal for auxiliary equipment
RS485 interface for communication (yellow wire)
RS485 interface for communication (green wire)
Negative power supply terminal
Positive power supply terminal
MANUAL ELDES ESIM264 V3.1
EN
119
47
C2
C1
Z1 Z2 Z3 Z4 Z5 Z6 Z7 Z8 Z9 Z10 Z11 Z12 Z13 Z14 Z15 Z16
STATUS
C1 C2 COM Z1 COM Z2 Z3 COM Z4 Z5 COM Z6 Z7 COM Z8 Z9 COM Z10 Z11 COM Z12 Z13COM Z14 Z15COM Z16 -AUX+ COM DC+ Y
G
48
C2
C1
Z1 Z2 Z3 Z4 Z5 Z6 Z7 Z8 Z9 Z10 Z11 Z12 Z13 Z14 Z15 Z16
EPGM1
STATUS
C1 C2 COM Z1 COM Z2 Z3 COM Z4 Z5 COM Z6 Z7 COM Z8 Z9 COM Z10 Z11 COM Z12 Z13COM Z14 Z15COM Z16 -AUX+ COM DC+ Y
Z16
Z15
Z14
Z13
Z11
Z12
Z10
Z9
Z8
Z7
Z6
Z5
Z4
Z3
Z1
Z2
5,6 kΩ
5,6 kΩ
5,6 kΩ
5,6 kΩ
5,6 kΩ
5,6 kΩ
5,6 kΩ
5,6 kΩ
5,6 kΩ
5,6 kΩ
5,6 kΩ
5,6 kΩ
5,6 kΩ
5,6 kΩ
5,6 kΩ
5,6 kΩ
RELAY
MODULE
G
AUX+
AUX-
G
Y
ESIM264
31.1.3.2. Installation
1. Disconnect ESIM264 alarm system main power supply and backup battery.
2. Connect EPGM1 DC+ terminal to ESIM264 AUX+ terminal, EPGM1 COM terminal to ESIM264 AUX- terminal, EPGM1 Y and G terminals
must be connected to ESIM264 Y and G terminals respectively (see Fig. No. 48).
3. Connect the resistors and sensors to EPGM1 module according to the selected zone connection Type 1, Type 2 or Type 3 (see 2.3.2
Zone Connection Types). If ATZ mode is enabled, please connect the resistors and sensors according to zone connection Type 1 or
Type 2.
4. Power up ESIM264 system.
5. Upon successful startup indicator STATUS should be blinking indicating successful EPGM1 operation.
6. EPGM1 is ready for use with ESIM264 alarm system.
NOTE: ATZ mode is not supported by EPGM1 zones.
NOTE: When ATZ mode is disabled, all EPGM1 zones must be wired in accordance with zone connection type set up in the system software-wise i.e. Type 1, Type 2 or Type 3. If ATZ mode is enabled, EPGM1 zones can be wired in accordance with Type 1 or Type 2 only
(mixed combination of these two zone connection types is permitted), regardless of the set up zone connection type in the system.
For more details on multiple EPGM1 module wiring, please refer to 3.2.7. RS485
120
EN
MANUAL ELDES ESIM264 V3.1
31.2. 1-Wire Interface
1-Wire interface is used for the system to communicate with an iButton key reader and up to 8 temperature sensors. 1-Wire interface COM and
DATA terminals are ground and data respectively. When connecting single or multiple temperature sensors, the +5V terminal must be used along.
For more details on 1-Wire device wiring, please refer to 32.2.1 iButton Key Reader and Buzzer
31.2.1. iButton Key Reader and Keys
The iButton key is a microchip enclosed in a stainless steel tab usually implemented in a small plastic holder. Each iButton key holds a
unique 64-bit identity code (ID), which is used for alarm system ESIM264 arming and disarming procedure.
Main iButton features:
• Up to 5 iButton keys per alarm system unit ESIM264;
• Communication via 1-Wire interface.
31.2.1.1. Technical Specifications
31.2.1.1.1 Electrical & Mechanical Characteristics
Supported iButton Key Model
Communication Interface
Maximum Cable Length for 1-Wire Communication
Maxim/Dallas DS1990A
1-Wire
up to 30 meters
31.2.1.1.2Installation
1. Disconnect ESIM264 alarm system main power supply and backup battery.
2. Connect iButton key reader contact wires to 1-Wire interface on ESIM264 alarm system: COM and DATA terminals respectively.
DATA
COM
49
iButton
key reader
3. Power up ESIM264 alarm system.
4 iButton key reader is ready for use with ESIM264 alarm system.
For more details on iButton key management, please refer to 11. iBUTTON KEYS.
31.3. Modules Interface
31.3.1. EPGM8 - Hardwired PGM Output Expansion Module
EPGM8 is a PGM output expansion module intended for using with alarm system ESIM264. This module allows to connect up to additional
8 electrical appliances.
Main EPGM8 features:
• PGM output expansion adding 8 additional PGM outputs;
• Compatible with ESIM264 alarm system
MANUAL ELDES ESIM264 V3.1
EN
121
31.3.1.1. Technical Specifications
31.3.1.1.1 Electrical & Mechanical Characteristics
Power Supply
Number of PGM Outputs
EPGM8 PGM Output Circuit
10-24V
8
100mA max
Maximum Commuting PGM Output Values
Dimensions
Humidity
Range of Operating Temperatures
Voltage – 30V; current 500mA
40 x 55 x 15 mm
1R
OUT
Open collector output.
Output is pulled to COM
when turned on.
0-90% RH @ 0... +40 °C (non-condensing)
-20...+55ºC
31.3.1.1.2 Connector Functionality
PGM output terminals
Positive power supply terminal
Negative power supply terminal
50
12V GND
D1 - D8
12V
GND
D1 D2 D3 D4 D5 D6 D7 D8
31.3.1.2. Installation
1. Disconnect ESIM264 alarm system main power supply and backup battery.
2. Insert EPGM8 pins into appropriate ESIM264 alarm system slots (see Fig. No. 51)
EPGM8
ESIM264
122
EN
12V GND
51
D1 D2 D3 D4 D5 D6 D7 D8
MANUAL ELDES ESIM264 V3.1
3. Connect EPGM8 12V positive power supply terminal with ESIM264 alarm system AUX+ terminal and EPGM8 GND terminal with
ESIM264 alarm system AUX- terminal. (see Fig. No. 52).
4. Connect the electrical appliances to D1 – D8 PGM outputs. (see Fig. No. 52).
52
ESIM264
AUX+
12V GND
AUX-
D1 D2 D3 D4 D5 D6 D7 D8
El. Appliance 1
TO AUX+
El. Appliance 2
TO AUX+
El. Appliance 3
TO AUX+
El. Appliance 4
TO AUX+
El. Appliance 5
TO AUX+
El. Appliance 6
TO AUX+
El. Appliance 7
TO AUX+
El. Appliance 8
TO AUX+
5. Power up ESIM264 alarm system.
6. 6. Enable EPGM8 mode using EKB2/EKB3 keypad or ELDES Configuration Tool software. For more details, please refer to software’s
HELP section or 18.2.1. EPGM8 Mode.
7. EPGM8 is ready for use with ESIM264 alarm system.
MANUAL ELDES ESIM264 V3.1
EN
123
31.3.2. EA1 – Audio Output Module
EA1 audio output module enables a duplex audio connection for ESIM264 alarm system.
Main EA1 features:
•
Two-way voice conversation during a phone call;
• Possibility to connect headphones or desktop speakers.
31.3.2.1. Technical Specifications
• 3,5 mm female jack
• Dimensions: 35 x 33 x 12 mm
31.3.2.2. Installation
1. Disconnect ESIM264 alarm system main power supply and backup battery.
2. Insert EA1 pins into appropriate ESIM264 alarm system slots.
53
EA1
ESIM264
3. Connect headphones or desktop speakers to EA1 3,5 mm female jack.
54
EA1
4. Power up ESIM264 alarm system.
5. EA1 is ready for use with ESIM264 alarm system.
124
EN
MANUAL ELDES ESIM264 V3.1
31.3.3. EA2 – Audio Output Module with Amplifier
EA2 audio output module enables a duplex audio connection for ESIM264 alarm system.
Main EA2 features:
• Two-way voice conversation during a phone call;
• Possibility to connect a speaker.
31.3.3.1. Technical Specifications
• 1W 8Ω audio amplifier
• Dimensions: 41 x 40 x 24 mm
31.3.3.2. Installation
1. Disconnect ESIM264 alarm system main power supply and backup battery.
2. Insert EA2 pins into appropriate ESIM264 alarm system slots.
55
ESIM264
EA2
3. Connect a speaker to EA2 Speaker terminals.
56
EA2
4. Power up ESIM264 alarm system.
5. EA2 is ready for use with ESIM264 alarm system.
MANUAL ELDES ESIM264 V3.1
EN
125
32.ELDES WIRELESS DEVICES
32.1. EWT1 - Wireless Transmitter-Receiver
Wireless transmitter-receiver EWT1 is an add-on module for ESIM264 system. It enables wireless transmission through alarm system
ESIM264 and ELDES wireless devices, such as: wireless PIR movement sensors EWP1, wireless expansion modules EW1 and EW1B, wireless
indoor sirens EWS1, wireless outdoor sirens EWS2, wireless magnetic door contacts EWD1, wireless magnetic door contacts/shock sensors
EWD2, wireless smoke detectors EWF1 and wireless key-fobs EWK1 and EWK2.
EWT1 enables ESIM264 alarm system to connect up to 16 wireless devices at a time. Maximum wireless connection range is 150 meters (in
open areas).
32.1.1. Technical Specifications
32.1.1.1. Electrical & Mechanical Characteristics
Wireless Transmitter-Receiver Frequency
868 MHz
Dimensions
68x38x18mm
Operating Temperature Range
-20...+55ºC
Wireless Communication Range
Up to 30 meters in premises; up to 150 meters in open areas
Maximum Number of Wireless Devices
16
32.1.2. Installation
57
ANTENNA SMA
LED
EWT1
ESIM264
1. Disconnect ESIM264 alarm system main power supply and backup battery.
2. 2. Insert EWT1 pins into appropriate ESIM264 slots as indicated in Fig. No. 57.
3. Mount the antenna to EWT1. It is not recommended to install the antenna inside the metal enclosure.
4. Power up ESIM264 system.
5. EWT1 is ready to use with ESIM264 system.
126
EN
MANUAL ELDES ESIM264 V3.1
32.2.EW1 - Wireless Zone & PGM Output Expansion Module
Main EW1B features:
•
2 zones for wired sensor connection;
•
2 PGM outputs for electrical appliance connection;
•
Powered by external power supply.
Wireless expansion module EW1 is a wireless device with 2 zones and 2 PGM outputs. This expansion module connects to ELDES wireless
alarm systems and enables wireless access for to 2 wired devices such as movement PIR sensors, magnetic door contacts etc. In addition it
allows to connect and control up to 2 appliances, i.e. lighting, heating etc. After the wiring process to EW1 it is necessary to bind EW1 to the
alarm system by sending a corresponding command via SMS text message or using software ELDES Configuration Tool.
It is possible to connect up to 16 EW1 devices to ESIM264 alarm system at a time. The maximum wireless connection range is 150 meters (in
open areas).
32.2.1. Technical Specifications
32.2.1.1. Electrical & Mechanical Characteristics
Power Supply
Number of Zones
Zone Connection Type
Number of PGM Outputs
Maximum Commuting PGM Output Values
EW1 PGM Output Circuit
7-15V
20mA max
2
Normally closed (NC)
2
Voltage – 30V; current 500mA
Wireless Transmitter-Receiver Frequency
Range of Operating Temperatures
Dimensions
Humidity
868 MHz
-20...+55ºC
38x60x12mm
Wireless Communication Range
Compatible with Alarm Systems
Up to 30 meters in premises; up to 150 meters in open areas
ELDES Wireless
MANUAL ELDES ESIM264 V3.1
1R
OUT
Open collector
output.
Output is pulled to
COM when turned on.
0-90% RH @ 0... +40 °C (non-condensing)
EN
127
58
COM
Z2
59
EW1
Z1
C2
LED
D1
D2
C1
DC+ C1 C2
Z1 Z2 COM
DC+
32.2.1.2. Connector & LED Functionality
COM
Z2, Z1
C2, C1
DC+
D1, D2
LED
Common terminal for power supply, zones
Security zone terminals
PGM output terminals
Positive power supply terminal
Pins for restoring default parameters
EW1 status
+12V
Power supply
32.2.2.Installation
1. Disconnect ESIM264 alarm system main power supply and backup battery.
2. Wire up EW1 as indicated in Fig. No. 59.
3. Bind the device to the alarm system by sending a corresponding command via SMS text message or using ELDES Configuration Tool
software. Please, refer to the software‘s HELP section or refer to 19.1. Binding, Removing and Replacing Wireless Devices for
more details.
4. T he system automatically informs about successful/unsuccessful binding process. If attempt to bind is unsuccessful, try to move EW1
closer to ESIM264 alarm system device and bind it again.
5. EW1 module is ready for use.
NOTE: If you are unable to bind the wireless device please , restore the parameters of the wireless device to default and try again. See
33.2.4 Restoring Default Parameters for more details.
ATTENTION: The minimum wireless connection range between the wireless device and wireless antenna of ESIM264 system can be
0,5 meters.
32.2.3.EW1 Zones, PGM Outputs & Tamper
Upon successful EW1 module binding process, the system adds 2 wireless Instant zones intended for wired sensor connection and 2 wireless
PGM outputs intended for electrical appliance connection and control.
The wireless connection loss between EW1 and ESIM264 alarm system leads to system alarm regardless of system being armed or disarmed.
The system identifies this event as a tamper violation and sends alarm by SMS text message and phone call to the user (-s) by default. The
SMS text message contains the violated tamper number and a star * character indicating wireless connection loss as a tamper alarm cause.
ATTENTION: The tamper will not operate if both wireless zones are disabled.
32.2.4.Restoring Default Parameters
1. 2. 3. 4. 5. 6. 7. Disconnect EW1 power supply.
Short circuit (connect) pins D1 and D2.
Power up EW1 and wait until LED provides several short flashes.
Disconnect power supply.
Remove short-circuit from D1 and D2 pins.
Power up EW1.
Parameters restored to default.
128
EN
MANUAL ELDES ESIM264 V3.1
32.3.EWP1 – Wireless Motion Detector
Main EWP1 features:
•
Violated zone detection by built-in PIR movement sensor.
EWP1 is a wireless device with built-in PIR movement sensor and operates with ELDES wireless alarm systems. The user only needs to switch
on the EWP1 sensor and bind it to ESIM264 alarm system by sending a corresponding command via SMS text message or using software ELDES
Configuration Tool. User can also monitor temperature of the surrounding areas in real-time as EWP1 has a built-in temperature sensor. It is
possible to connect up to 16 EWP1 devices to ESIM264 alarm system at a time. The maximum wireless connection range is 150 meters (in
open areas).
32.3.1. Technical Specifications
32.3.1.1. Electrical & Mechanical Characteristics
Battery Type
Battery Voltage; Capacity
Battery Operation Time
Wireless Transmitter-Receiver Frequency
Range of Operating Temperatures
Dimensions
Humidity
ER14505 AA Lithium Thionyl Chloride
3,6 V; 2,4 Ah
~18 months*
868 MHz
-10 ... +55°C
104x60x33mm
Detection Coverage Angle
Maximum Detection Distance
Compatible with Alarm Systems
Wireless Communication Range
90°
10 meters
ELDES Wireless
Up to 30 meters in premises; up to 150 meters in open areas
0-90% RH @ 0... +40 °C (non-condensing)
* The operation time depends on different conditions and may vary.
60
1
2
1
Motion detector
2
LED indicators informing about status of PIR sensor EWP1
3
TAMPER button automatically identifies when the box of sensor
EWP1 is open or closed
4
RESET button for reseting system parameters
5
ER14505 3,6 V Lithium Thionyl Chloride battery
3
4
5
32.3.2.Installation
1. Choose the place where intrusion into the premises is the most probable and install the device. To avoid false triggers of the system do
not install it in the following places:
• directing the lens to direct sunlight, for example, to the window of the premises;
• where there is a risk of sudden temperature alteration, for example, near a fireplace or heating system;
• where there is an enlarged possibility of dust or air flow;
• behind the curtain or some other cover blocking the detected zone.
61
2. Fix EWP1 sensors mounting holder with two screws to the wall and attach the sensor.
MANUAL ELDES ESIM264 V3.1
EN
129
3. Bind the device to the alarm system by sending a corresponding command via SMS text message or using ELDES Configuration Tool
software. Please, refer to the software‘s HELP section or refer to 19.1. Binding, Removing and Replacing Wireless Devices for
more details.
4. The system automatically informs about successful/unsuccessful binding process. If attempt to bind is unsuccessful, try to move EWP1
closer to alarm system device and bind it again.
5. EWP1 is ready to use.
NOTE: If you are unable to bind the wireless device please , restore the parameters of the wireless device to default and try again. See
32.3.5. Restoring Default Parameters for more details.
ATTENTION: The minimum wireless connection range between the wireless device and wireless antenna of ESIM264 system can be
0,5 meters.
32.3.3.EWP1 Zone & Tamper
Upon successful EWP1 sensor binding process, the system adds 1 wireless Instant zone intended for movement detection. By, default, the
alarm is caused instantly if any movement is detected in coverage area of the sensor (when system is armed).
In case of tamper violation, the alarm is caused regardless of system being armed or disarmed. There are 2 ways to detect tamper violation
on EWP1 sensor:
• By tamper button. EWP1 has a built-in tamper button intended for monitoring the enclosure status. Once the enclosure of EWP1
is illegally opened, the tamper button becomes unpressed. This action is followed by alarm which is sent by SMS text message and
phone call to the user (-s) by default. The SMS text message contains the violated tamper number.
•
By wireless connection loss. The wireless connection loss between EWP1 sensor and ESIM264 system leads to alarm. The system identifies this event as a tamper violation and sends alarm by SMS text message and phone call to the user (-s) by default. The SMS text message
contains the violated tamper number and a star * character indicating wireless connection loss as a tamper alarm cause.
ATTENTION: The tamper will not operate if the wireless zone is disabled.
32.3.4.Battery Replacement
1. Open EWP1 enclosure.
2. Remove the old battery from the battery slot.
3. Postition the new battery according to the appropriate battery slot positive/negative terminals indicated on the PCB (prin­ted-circuitboard) of EWP1.
4. Insert the battery into the battery slot.
5. Batteries replaced.
For more details, please refer to 32.3.2. Installation.
ATTENTION: Only ER14505 Lithium Thionyl Chlorid AA type batteries can be used. Install only new, high quality and unexpired batteries. Do not mix the old batteries with the new ones.
ATTENTION: At least 1 battery must be removed if the device is not in use.
ATTENTION: In order to avoid fire or explosion hazards, the system must be used only with approved battery. Special care must be taken
when connecting positive and negative battery terminals. Dispose old batteries only into special collection sites. Do not charge, disassemble,
heat or incinerate old batteries.
NOTE: The battery status can be monitored in real-time using ELDES Configuration Tool software.
NOTE: The system sends an SMS message to a preset User 1 as soon as the battery level runs below 5%.
32.3.5.Restoring Default Parameters
1. Remove any battery from EWP1.
2. Press and hold the RESET button.
3. Insert the battery back to EWP1.
4. Hold the RESET button until LED indicator provides several short flashes.
5. Release the RESET button.
6. Parameters restored to default.
130
EN
MANUAL ELDES ESIM264 V3.1
32.4.EWD1 – Wireless Magnetic Door Contact
Main EWD1 features:
•
Violated zone detection by magnetic contact;
•
Panic button.
EWD1 is a wireless device with magnetic contact and panic button which is used to secure doors, windows or any other opening parts and
it operates with ELDES wireless alarm systems. EWD1 is bind to ESIM264 alarm system by sending a corresponding command via SMS text
message or using software ELDES Configuration Tool. When EWD1 is connected to the system, two wireless zones are added. First wireless
zone is used to monitor the magnetic contacts and the second wireless zone is for managing the panic button. By default panic button zone is
configured as Silent zone and in case the panic button is pressed, the system causes silent alarm (no siren is activated).
It is possible to connect up to 16 EWD1 devices to ESIM264 alarm system at a time. The maximum wireless connection range is 150 meters (in
open areas).
32.4.1.Technical Specifications
32.4.1.1.Electrical & Mechanical Characteristics
Battery Type
Number of Batteries
Battery Operation time
Wireless Transmitter-Receiver Frequency
Range of Operating Temperatures
Door Contact Dimensions
Humidity
CR2032 3V Lithium
1
15 months*
868 Mhz
-20...+55ºC
60x37x18mm
Magnet Dimensions
Wireless Communication Range
Compatible with Alarm Systems
60x17x16mm
Up to 30 meters in premises; up to 150 meters in open areas
ELDES Wireless
0-90% RH @ 0... +40 °C (non-condensing)
* The operation time depends on different conditions and may vary.
32.4.2.Installation
1. Open EWD1 enclosure and insert the battery (Fig. No. 62).
62
RESET
LED
+
3V
CR2032
+
2. EWD1 consists of two parts: a magnet and a sensor. Sensor components are: a mounting part and the sensor. Magnet components are:
a mounting part and the cover.
2.1 Fix the sensor mounting part with two screws on the door or window jamb.
2.2 Fix the magnet mounting part with two screws next to the sensor mounting part on door or window frame. The correct fixing position
is indicated in Fig. No. 63.
63
MAX 20 mm
NOTE: The distance between magnet and sensor can be up to 20 mm only.
2.3 The sensor should be attached to the fixed sensors mounting part. When attaching sensor pay attention to the tamper (micro switch)
- it must be pressed.
2.4 The magnet cover should be attached to the fixed magnet mounting part.
MANUAL ELDES ESIM264 V3.1
EN
131
NOTE: It is not recommend to fix EWD1 in other ways than with screws, e.g. with duck tape. See Fig. No. 64 for the incorrect ways of
fixing the magnetic door contact.
64
3. Bind the device to the alarm system by sending a corresponding command via SMS text message or using ELDES Configuration Tool
software. Please, refer to the software‘s HELP section or refer to 19.1. Binding, Removing and Replacing Wireless Devices for
more details.
4. The system automatically informs about successful/unsuccessful binding process. If attempt to bind is unsuccessful, try to move EWD1
closer to alarm system device and bind it again.
5. EWD1 magnetic door contact is ready to use.
NOTE: If you are unable to bind the wireless device please , restore the parameters of the wireless device to default and try again. See
32.4.5. Restoring Default Parameters for more details.
ATTENTION: The minimum wireless connection range between the wireless device and wireless antenna of ESIM264 system can be
0,5 meters.
32.4.3.EWD1 Zones & Tamper
Upon successful EWD1 magnetic door contact binding process,the system adds 1 wireless Instant zone and 1 wireless Panic/Silent zone.
The wireless zones are applied to the following EWD1 components respectively:
• Magnetic contact - by default, causing alarm if doors/windows is opened when system is armed.
• Panic button - by default, causing silent alarm instantly when pressed.
In case of tamper violation, the alarm is caused regardless of system being armed or disarmed. There are 2 ways to detect tamper violation
on EWD1:
• By tamper button. EWD1 has a built-in tamper button intended for monitoring the enclosure status. Once the enclosure of EWD1 is
illegally opened, the tamper button becomes unpressed. This action is followed by alarm which is sent by SMS text message and phone
call to the user (-s) by default. The SMS text message contains the violated tamper number.
•
By wireless connection loss. The wireless connection loss between EWD1 and ESIM264 system leads to alarm. The system identifies this event
as a tamper violation and sends alarm by SMS text message and phone call to the user (-s) by default. The SMS text message contains the violated
tamper number and a star * character indicating wireless connection loss as a tamper alarm cause.
ATTENTION: The tamper will not operate if both wireless zones are disabled.
32.4.4.Battery Replacement
1. Open EWD1 enclosure.
2. Remove the old battery from the battery slot.
3. Postition the new battery according to the appropriate batte­ry slot positive terminal indicated.
4. Insert the battery into the battery slot.
5. Battery replaced.
For more details, please refer to 32.4.2. Installation.
ATTENTION: Only ER14505 Lithium Thionyl Chlorid AA type batteries can be used. Install only new, high quality and unexpired batteries. Do not mix the old batteries with the new ones.
ATTENTION: At least 1 battery must be removed if the device is not in use.
ATTENTION: In order to avoid fire or explosion hazards, the system must be used only with approved battery. Special care must be taken
when connecting positive and negative battery terminals. Dispose old batteries only into special collection sites. Do not charge, disassemble,
heat or incinerate old batteries.
132
EN
MANUAL ELDES ESIM264 V3.1
NOTE: The battery status can be monitored in real-time using ELDES Configuration Tool software.
NOTE: The system sends an SMS message to a preset User 1 as soon as the battery level runs below 5%.
32.4.5.Restoring Default Parameters
1. Remove the battery from EWD1.
2. Press and hold the RESET button.
3. Insert the battery back to EWD1.
4. Hold the RESET button until LED indicator provides several short flashes.
5. Release the RESET button.
6. Parameters restored to default.
32.5.EWK1 - Wireless Keyfob
Main EWK1 features:
•
Alarm system arming & disarming;
•
Panic button;
•
PGM output control;
•
Sound indication by built-in mini buzzer.
Keyfob EWK1 – is a wireless device intended to arm and disarm ESIM264 alarm system, to open and close the gates or to control any other device connected to the alarm system. Wireless keyfob EWK1 is compatible with ELDES wireless alarm systems, therefore user can easily bind it to
the alarm system using ELDES Configuration Tool software or sending a corresponding SMS command. EWK1 keyfob features four configurable
buttons intended to operate according to individual needs. After the button is pressed, EWK1 internal buzzer’s sound signal confirms a transferred command to ESIM264 alarm system via wireless connection. The status of the sent command can be checked by attempting to receive
the feedback signal from the alarm system. This can be performed by pressing down the same button and holding it for 3 seconds. 3 short sound
signals indicate a successfully carried out command while 1 long beep stands for failed command and feedback signal failure. By default one pair
of buttons is already configured to arm and disarm the alarm system.
The virtual zones of ESIM264 system are intended for EWK1 button configuration. Please, refer to software’s ELDES Con­figuration Tool HELP section
for more details.
65
Optional
functionality
Disarm the
system
Arm the
system
Optional
functionality
It is possible to connect up to 5 EWK1 devices to ESIM264 alarm system at
a time. The maximum wireless connection range is 150 meters (in open
areas).
NOTE: Fig. No. 65 reflects the default EWK1 button configuration. All keyfob buttons are configurable according to individual needs.
32.5.1. Technical Specifications
32.5.1.1. Electrical & Mechanical Characteristics
Battery Type
Battery Voltage; Capacity
Quantity of Batteries
Battery Operation Time
Wireless Transmitter-Receiver Frequency
Range of Operating Temperatures
Wireless Keyfob Dimensions
Humidity
CR2032 Lithium
3V; 240 mAh
1
~18 months*
868 Mhz
-20...+55ºC
54 x 42 x 13 mm
Wireless Communication Range
Compatible with Alarm Systems
Up to 30 meters in premises; up to 150 meters in open areas
ELDES Wireless
0-90% RH @ 0... +40 °C (non-condensing)
* The operation time depends on different conditions and may vary.
MANUAL ELDES ESIM264 V3.1
EN
133
32.5.2.Installation
67
66
1. Unscrew the EWK1 keyfob housing.
2. Open EWK1 keyfob housing.
3. Insert CR2032 battery provided in the EWK1 package.
Before inserting the battery, make sure that the battery’s “+” sign is facing the outer side.
68
+
3V
CR2032
+
4. Close and screw up the keyfob housing.
5. Bind the device to the alarm system by sending a corresponding command via SMS text message or using ELDES Configuration Tool software. Please, refer to the software‘s HELP section or refer to 19.1. Binding, Removing and Replacing Wireless Devices for more
details.
6. While binding the device to the alarm system, press any EWK1 button several times.
7. EWK1 is ready to use.
NOTE: If you are unable to bind the wireless device please , restore the parameters of the wireless device to default and try again. See
32.5.5. Restoring Default Parameters for more details.
32.5.3.EWK1 Zones (Panic Button)
EWK1 keyfob supports a Panic Button feature allowing to cause alarm at any time when the specified button is pressed. This feature can be
configured using ELDES Configuration Tool software by creating a virtual zone of Panic/Silent or 24-Hour type and assigning it to Virtual Alarm
option. The Panic Button feature can be set up on any button of EWK1. For more details, please refer to software’s HELP section.
32.5.4.Battery Replacement
1. Open EWD1 enclosure.
2. Remove the old battery from the battery slot.
3. Postition the new battery according to the appropriate battery slot positive terminal indicated.
4. Insert the battery into the battery slot.
5. Battery replaced.
For more details, please refer to 32.5.2 Installation.
ATTENTION: Only CR2032 3V batteries can be used. Install only new, high quality and unexpired batteries. Do not mix the old batteries
with the new ones.
ATTENTION: At least 1 battery must be removed if the device is not in use.
ATTENTION: In order to avoid fire or explosion hazards, the system must be used only with approved battery. Special care must be
taken when connecting positive and negative battery terminals. Dispose old batteries only into special collection sites. Do not charge,
disassemble, heat or incinerate old batteries.
134
EN
MANUAL ELDES ESIM264 V3.1
NOTE: The battery status can be monitored in real-time using ELDES Configuration Tool software.
32.5.5.Restoring Default Parameters
1. Remove the battery from EWK1 keyfob.
2. Press and hold
button.
3. Insert the battery back to EWK1.
4. Hold the button pressed until LED indicator provides several short flashes.
5. Release
button.
6. Parameters restored to default.
32.6.EWS1 – Wireless Indoor Siren
Main EWS1 features:
•
Audio alarm indication by built-in speaker.
EWS1 is a wireless device with built-in siren speaker and operates with ELDES wireless alarm systems. EWS1 has to be bind to the alarm system by sending a corresponding SMS text message or using software ELDES Configuration Tool. Upon successful EWS1 binding, the system
adds one wireless zone and one wireless PGM output. The wireless zone is used to monitor the device (tamper - when the batteries are being
removed) and the wireless PGM output is used to control the speaker. In case of alarm, the siren provides a sound alarm for one minute. The
configuration of this parameter is disabled for EWS1 in order to save the battery power.
It is possible to connect up to 16 EWS1 devices to the alarm system at a time. The maximum wireless connection range is 150 meters (in open
areas).
32.6.1.Technical Specifications
69
32.6.1.1. Electrical & Mechanical Characteristics
Compatible with Alarm Systems
Acoustic sound level
LED
RESET
BATTERY
-
+
+
Up to 30 meters in premises; up to 150 meters in open areas
ELDES Wireless
~97 dB measured at
1m
BATTERY
+
Wireless Communication Range
0-90% RH @ 0... +40 °C
(non-condensing)
-
BATTERY
1,5V Alkaline AA type
3
~18 months*
868 Mhz
-20...+55ºC
123x73x36mm
-
Battery Type
Number of Batteries
Battery Operation Time
Wireless Transmitter-Receiver Frequency
Range of Operating Temperatures
Dimensions
Humidity
* The operation time depends on different conditions and may vary.
32.6.1.2.Main Unit & LED Functionality
RESET
+/LED
Button for restoring default parameters
Battery slots
EWS1 status indication
MANUAL ELDES ESIM264 V3.1
EN
135
32.6.2.Installation
1.
Open EWS1 enclosure.
70
71
Insert a thin flat-shaped screwdriver or any tool alike into the gap lo­
cated on the back of the enclosure (see Fig. No. 70).
Push the screwdriver down to the right carefully in order to detach
the enclosure parts from each other (see Fig. No. 71).
2. Once the enclosure is opened, remove the plastic tab inserted between one of the battery terminals and battery slot contact (see Fig. No.
72).
72
3. Fix the siren on the wall using the screws (see Fig. No. 73).
73
-
RESET
BATTERY
LED
+
+
BATTERY
-
+
-
BATTERY
4. Close EWS1 enclosure. No tools are required for this action.
5. Bind the device to the alarm system by sending a corresponding command via SMS text message or using ELDES Configuration Tool software.
Please, refer to the software‘s HELP section or refer to 19.1. Binding, Removing and Replacing Wireless Devices for more details.
6. The system automatically informs about successful/unsuccessful binding process. If attempt to bind is unsuccessful, try to move EWS1
closer to alarm system device and bind it again.
7. EWS1 siren is ready for use.
NOTE: If you are unable to bind the wireless device please , restore the parameters of the wireless device to default and try again. See
32.6.5. Restoring Default Parameters for more details.
136
EN
MANUAL ELDES ESIM264 V3.1
ATTENTION: The minimum wireless connection range between the wireless device and wireless antenna of ESIM264 system can be
0,5 meters.
32.6.3.EWS1 Zone, PGM Output & Tamper
Upon successful EWS1 indoor siren binding process,the system adds 1 wireless Instant zone and 1 wireless Siren PGM output. The wireless
zone is intended for EWS1 tamper control and the wireless PGM output is for siren control.
In case of tamper violation, the alarm is caused regardless of system being armed or disarmed. The wireless connection loss between EWS1
and ESIM264 system leads to alarm. The system identifies this event as a tamper violation and sends alarm by SMS text message and phone
call to the user (-s) by default. The SMS text message contains the violated tamper number and a star * character indicating wireless connection loss as a tamper alarm cause.
ATTENTION: The tamper will not operate if the wireless zone is disabled.
32.6.4.Battery Replacement
1. Open EWS1 enclosure.
2. Remove all 3 old batteries from the battery slots.
3. Postition the 3 new 1,5V alkaline AA type batteries according to the appropriate battery slot positive/negative terminals indicated on the
PCB (printed-circuit-board) of EWS1
4. Insert the batteries into the battery slots.
5. Batteries replaced.
For more details, please refer to 32.6.2 Installation.
ATTENTION: Only CR2032 3V batteries can be used. Install only new, high quality and unexpired batteries. Do not mix the old batteries
with the new ones.
ATTENTION: At least 1 battery must be removed if the device is not in use.
ATTENTION: In order to avoid fire or explosion hazards, the system must be used only with approved battery. Special care must be
taken when connecting positive and negative battery terminals. Dispose old batteries only into special collection sites. Do not charge,
disassemble, heat or incinerate old batteries.
NOTE: The battery status can be monitored in real-time using ELDES Configuration Tool software.
32.6.5.Restoring Default Parameters
1. Remove any battery from EWS1.
2. Press and hold the RESET button.
3. Insert the battery back to EWS1.
4. Hold the RESET button until LED indicator provides several short flashes.
5. Release the RESET button.
6. Parameters restored to default.
32.7.EWS2 – Wireless Outdoor Siren
Main EWS2 features:
•
Audio alarm indication by built-in speaker;
•
Visual alarm indication by built-in LED indicators;
•
Range of operating temperature: -30...+55oC.
EWS2 is a wireless outdoor device with a built-in siren speaker, LED indicators and operates with ELDES wireless alarm systems. EWS2 has to
be bind to the alarm system by sending a corresponding SMS text message or using software ELDES Configuration Tool. Upon successful EWS2
binding process, the system adds one wireless zone and one wireless PGM output. In case of alarm, the siren provides a sound alarm for one
minute. The configuration of this parameter is disabled for EWS2 in order to save the battery power.
It is possible to connect up to 16 EWS2 devices to the alarm system at a time. The maximum wireless connection range is 150 meters (in open
areas).
MANUAL ELDES ESIM264 V3.1
EN
137
32.7.1. Technical Specifications
32.7.1.1. Electrical & Mechanical Characteristics
74
1,5V Alkaline AA type
4
~18 months*
868 Mhz
-30...+55ºC
201 x 140 x 36 mm
Wireless Communication Range
Up to 30 meters in premises; up to
150 meters in open areas
ELDES Wireless
~104 dB measured at 1 m
Compatible with Alarm Systems
Acoustic sound level
TAMPER
Battery Type
Number of Batteries
Battery Operation Time
Wireless Transmitter-Receiver Frequency
Range of Operating Temperatures
Dimensions
Humidity
0-90% RH @ 0... +40 °C (non-condensing)
TAMPER
+ BELL
+
BATTERY
-
+
BATTERY
-
-
BATTERY
+
-
BATTERY
+
* The operation time depends on different conditions and may vary.
32.7.1.2. Main Unit, LED & Connector Functionality
RESET
+/LED indicators
Tamper
Bell+
Bell-
RESET
Button for restoring default parameters
Battery slots
Visual alarm indication
Tamper button terminals
Positive siren speaker terminal
Negative siren speaker terminal
32.7.2.Installation
1. Open EWS2 enclosure.
75
76
Remove the small blue lid located on the front side of the enclosure
by pulling the lid up. (see Fig. No. 75).
Unscrew the front side of the enclosure (see Fig. No. 76).
2. Once the enclosure is opened, remove the plastic tab inserted between one of the battery terminal and battery slot contact (see Fig. No. 77).
77
3. Fix the siren on the wall using the screws (see Fig. No. 78).
138
EN
MANUAL ELDES ESIM264 V3.1
78
+
BATTERY
-
+
BATTERY
-
-
BATTERY
+
-
BATTERY
+
4. Close EWS2 enclosure (see Fig. No. 76, Fig. No. 75)
5. Bind the device to the alarm system by sending a corresponding command via SMS text message or using ELDES Configuration Tool software. Please, refer to the software‘s HELP section or refer to 19.1. Binding, Removing and Replacing Wireless Devices for more
details.
6. The system automatically informs about successful/unsuccessful binding process. If attempt to bind is unsuccessful, try to move EWS2
closer to alarm system device and bind it again.
7. EWS2 siren is ready for use.
NOTE: If you are unable to bind the wireless device please , restore the parameters of the wireless device to default and try again. See
32.7.6. Restoring Default Parameters for more details.
ATTENTION: The minimum wireless connection range between the wireless device and wireless antenna of ESIM264 system can be
0,5 meters.
32.7.3.EWS2 Zone, PGM Output & Tamper
Upon successful EWS2 outdoor siren binding process,the system adds 1 wireless Instant zone and 1 wireless Siren PGM output. The wireless
zone is intended for EWS2 tamper control and the wireless PGM output is for siren control.
In case of tamper violation, the alarm is caused regardless of system being armed or disarmed. There are 2 ways to detect tamper violation
on EWS2:
• By tamper button. EWS2 has a built-in tamper button intended for monitoring the enclosure status. Once the enclosure of EWS2
is illegally opened, the tamper button becomes unpressed. This action is followed by alarm which is sent by SMS text message and
phone call to the user (-s) by default. The SMS text message contains the violated tamper number.
• By wireless connection loss. The wireless connection loss between EWS2 and ESIM264 alarm system leads to alarm. The sys­tem
identifies this event as a tamper violation and sends alarm by SMS text message and phone call to the user (-s) by default. The SMS
text message contains the violated tamper number and a star * character indicating wireless connection loss as a tamper alarm cause.
ATTENTION: The tamper will not operate if the wireless zone is disabled.
32.7.4.Battery Replacement
1. Open EWS2 enclosure.
2. Remove all 4 old batteries from the battery slots.
3. Postition the 4 new 1,5V alkaline AA type batteries according to the appropriate battery slot positive/negative terminals indicated on the
PCB (printed-circuit-board) of EWS2
4. Insert the batteries into the battery slots.
5. Batteries replaced.
For more details, please refer to 32.7.2 Installation.
ATTENTION: Only 1,5V Alkaline AA type batteries can be used. Install only new, high quality and unexpired batteries. Do not mix the old
batteries with the new ones.
MANUAL ELDES ESIM264 V3.1
EN
139
ATTENTION: At least 1 battery must be removed if the device is not in use.
ATTENTION: In order to avoid fire or explosion hazards, the system must be used only with approved battery. Special care must be
taken when connecting positive and negative battery terminals. Dispose old batteries only into special collection sites. Do not charge,
disassemble, heat or incinerate old batteries.
NOTE: The system sends an SMS message to a preset User 1 as soon as the battery level runs below 5%.
NOTE: The battery status can be monitored in real-time using ELDES Configuration Tool software.
32.7.5.Restoring Default Parameters
1. 2. 3. 4. 5. 6. Remove any battery from EWS2.
Press and hold the RESET button.
Insert the battery back to EWS2.
Hold the RESET button until LED indicator provides several short flashes.
Release the RESET button.
Parameters restored to default.
32.8.EW1B - Battery-Powered Wireless Zone & PGM Output Expansion Module
Main EW1B features:
•
•
2 zones for wired sensor connection;
2 PGM outputs for electrical appliance connection.
Wireless expansion module EW1B is a wireless device with 2 zones and 2 PGM outputs. This expansion module connects to ELDES wireless
alarm systems and enables wireless access for to 2 wired devices such as movement PIR sensors, magnetic door contacts etc. In addition it
allows to connect and control up to 2 appliances, i.e. lighting, heating etc. After the wiring process to EW1B it is necessary to bind EW1B to the
alarm system by sending a corresponding command via SMS text message or using software ELDES Configuration Tool. t is possible to connect
up to 16 EW1B devices to ESIM264 alarm system at a time. The maximum wireless connection range is 150 meters (in open areas).
32.8.1.Technical Specifications
32.8.1.1.Electrical & Mechanical Characteristics
Battery Type
Number of Batteries
Battery Operation Time
Number of Zones
Zone Connection Type
1,5V Alkaline AA type
3
~18 months*
2
Normally closed (NC)
Number of PGM Outputs
EW1B PGM Output Circuit
2
Maximum Commuting PGM Output Values
Wireless Transmitter-Receiver Frequency
Wireless Communication Range
Voltage – 30V; current 500mA
868 MHz
Up to 30 meters in premises; up to 150 meters in open areas
ELDES Wireless
-20...+55ºC
38x60x12mm
90x110x40mm
Compatible with Alarm Systems
Range of Operating Temperatures
EW1B PCB Dimensions
EW1B Enclosure Dimensions
Humidity
Enclosure rating
1R
OUT
Open Collector Output.
Output is pulled to COM
when turned ON.
0-90% RH @ 0... +40 °C (non-condensing)
IP65
* The operation time depends on different conditions and may vary.
140
EN
MANUAL ELDES ESIM264 V3.1
32.8.1.2.Connector & LED Functionality
COM
Common terminal for zones
Z2, Z1
Security zone terminals
C2, C1
PGM output terminals
D1, D2
Pins for restoring default parameters
LED
EW1B status
79
D1
D2
LED
COM
Z2
Z1
C2
C1
+ BATTERY –
– BATTERY +
+ BATTERY –
32.8.2.Installation
80
3. Remove the plastic tab inserted between one of the battery
terminals and battery slot contacts (see Fig. No. 82).
82
2. Detach the front side of the enclosure by pulling the front side
up (see Fig. No. 81)
81
4. Connect the ciruit as indicated in Fig. No. 83.
83
EW1B
Z1 Z2 COM
Sensor
C1 C2
Sensor
1. Push down the screwdriver and turn it counter-clockwise to unscrew EW1B enclosure (see Fig. No. 80)
6. Close EW1B enclsoure (see Fig. No. 81, Fig. No. 80).
7. Bind the device to the alarm system by sending a corresponding command via SMS text message or using ELDES Configuration Tool software.
Please, refer to the software‘s HELP section or refer to 19.1. Binding, Removing and Replacing Wireless Devices for more details.
8. The system automatically informs about successful/unsuccessful binding process. If attempt to bind is unsuccessful, try to move EW1B
closer to alarm system device and bind it again.
9. EW1B is ready for use.
MANUAL ELDES ESIM264 V3.1
EN
141
NOTE: If you are unable to bind the wireless device please , restore the parameters of the wireless device to default and try again. See
33.8.5. Restoring Default Parameters for more details.
ATTENTION: The minimum wireless connection range between the wireless device and wireless antenna of ESIM264 system can be 0,5
meters.
32.8.3. EW1B Zones, PGM Outputs & Tamper
Upon successful EW1B module binding process, the system adds 2 wireless Instant zones intended for wired sensor connection and 2 wire-
less PGM outputs intended for electrical appliance connection and control. The wireless connection loss between EW1B and ESIM264 alarm
system leads to system alarm regardless of system being armed or disarmed. The system identifies this event as a tamper violation and sends
alarm by SMS text message and phone call to the user (-s) by default. The SMS text message contains the violated tamper number and a star *
character indicating wireless connection loss as a tamper alarm cause.
32.8.4.Battery Replacement
1. Open EW1B enclosure.
2. Remove all 3 old batteries from the battery slots.
3. Postition the 3 new 1,5V alkaline AA type batteries according to the appropriate battery slot positive/negative terminals as indicated.
4. Insert the batteries into the battery slots.
5. Batteries replaced.
For more details, please refer to 32.8.2. Installation.
ATTENTION: Only 1,5V Alkaline AA type batteries can be used. Install only new, high quality and unexpired batteries. Do not mix the old
batteries with the new ones.
ATTENTION: At least 1 battery must be removed if the device is not in use.
ATTENTION: In order to avoid fire or explosion hazards, the system must be used only with approved battery. Special care must be
taken when connecting positive and negative battery terminals. Dispose old batteries only into special collection sites. Do not charge,
disassemble, heat or incinerate old batteries.
NOTE: The system sends an SMS message to a preset User 1 as soon as the battery level runs below 5%.
NOTE: The battery status can be monitored in real-time using ELDES Configuration Tool software.
32.8.5.Restoring Default Parameters
1. Remove any battery from EW1B.
2. Short circuit (connect) pins D1 and D2.
3. Insert the battery back to EW1B.
4. Wait untill LED provides several short flashes.
5. Remove short-circuit from D1 and D2 pins.
6. Parameters restored to default.
142
EN
MANUAL ELDES ESIM264 V3.1
32.9.EWF1 - Wireless Smoke Detector
Main EWF1 features:
•
•
•
•
Photoelectric sensor for slow smouldering fires
TEST button
Non-radioactive technology for environmental friendly
High and stable sensitivity
•
•
•
•
Quick fix mounting plate for easy installation
LED operation indicator
Built-in speaker for audio alarm indication
Auto-reset when smoke clears
EWF1 is a wireless photoelctric type smoke detector intended to use with ELDES wireless alarm systems. Photoelectric smoke detectors
are generally more effective at detecting smouldering fires which smoulder for hours before bursting into flame. An optical method
is used for the detection of visible smoke. When the concentration of smoke in the optical chamber exceeds a given threshold, EWF1
sounds the alarm and sends out a signal to the ESIM264 alarm system using the wireless connection and the system triggers the alarm.
By default, when more than one EWF1 device is used, the system will automatically activate the interconnection feature (see 32.9.4.
In­terconnection). ESIM264 system support up to 16 EWF1 devices, The maximum wireless connection range is 150 meters (in open
areas).
32.9.1.Technical Specifications
32.9.1.1. Electrical & Mechanical Characteristics
Detection Type
Alarm Sound Level
Photoelectric chamber
85 Decibels at 3 meters
9V
6F22 primary alkaline
1
~18 months*
868 Mhz
Up to 30 meters in premises; up to 150 meters in open areas
5oC to 45oC
0-90% RH @ 0... +40 °C (non-condensing)
3.0-6.0 % Obs /m
110mm Ø
ELDES Wireless
~98 dB measured at 1 m
Battery Voltage
Battery Type
Number of Batteries
Battery Operation Time
Wireless Transmitter-Receiver Frequency
Wireless Communication Range
Range of Operating Temperatures
Humidity
Sensitivity to Smoke
Dimensions
Compatible with Alarm Systems
Acoustic sound level
* The operation time depends on different conditions and may vary.
32.9.1.2.Main Unit & LED Functionality
TEST
LED
SIREN
RESET**
Button for testing / button for testing and restoring default parameters (if RESET button not available)
EWF1 status indication
Built-in speaker for audio alarm indication
Button for restoring default parameters
84
FRONT SIDE
Siren
BACK SIDE
TEST button
LED indicator
RESET button**
BATTERY
** Unavailaible on some EWF1 models
MANUAL ELDES ESIM264 V3.1
EN
143
32.9.2.PLACEMENT
1. Install the wireless smoke detector as close to the center of the ceiling as possible. If this is not practical, mount no closer than 10
centimeters from a wall or corner. Also, if local codes allow, install wireless smoke detectors on walls, between 10 and 30 centimeters
from ceiling/wall intersections.
2. Install a minimum of two wireless smoke detectors in every house, no matter how small the house is.
3. Install a wireless smoke detector in each room that is divided by a partial wall (either coming down from the ceiling at least 20 centimeters, or coming up from the floor).
4. Install a wireless smoke detector in lived-in attics or attics which ho use electrical equipment like furnaces, air conditioners, or heaters.
NOTE: For best protection we recommend that you install a wireless smoke detector in every room.
Recommended EWF1 placement locations
85
(0,1 m)
Ceiling
RE
HE A
YW RE
AN HIS A
T
IN
0,9 m (3 ft)
Acceptable
here
NEVER
HERE
(0,1 m)
Max.
(0,3 m)
Max.
Top of detector
acceptable here
0,9 m (3 ft)
HORIZONTAL DISTANCE
Wall
NOTE: Measurements shown are to the closest edge of the detector.
Typical Single-Story House
Install a wireless smoke detector on the ceiling or wall inside each bedroom and in the hallway outside each separate sleeping area. If a
bedroom area hallway is more than 9 meters long, install a wireless smoke detector at each end.
If there is a basement: Install a wireless smoke detector on the basement ceiling at the bottom of the stairwell.
86
Bedroom
Bedroom
Living Room
Family Room
LEGEND:
Dining Room
Kitchen
Bedroom
Minimum required smoke
detector locations.
Recommended additional
smoke detector locations
144
EN
MANUAL ELDES ESIM264 V3.1
Typical Multi-Story or Split-Level House
Install a wireless smoke detector on the ceiling or wall inside each
bedroom and in the hallway outside each separate sleeping area. If
a bedroom area hallway is more than 9 meter long, install a wireless smoke detector at each end. Please install a wireless smoke
detector on the top of a first-to-second floor stairwell.
87
Bedroom
LEGEND:
Bedroom
Minimum required smoke detector locations.
Recommended additional smoke detector locations
Living
Room
Dining
Room
Basement
Incorrect EWF1 Placement
DO NOT place EWF1 in the following locations:
•
•
•
•
•
Near appliances or areas where normal combustion regularly occurs (kitchens, near furnaces, hot water heaters). Use specialized
wireless smoke detector with unwanted alarm control for this areas.
In areas with high humidity, like bathrooms or areas near dishwashers or washing machines. Install at least 3 meters away from these
areas.
Near air returns or heating and cooling supply vents. Install at least 1 meter away from these areas. The air could blow smoke away
from the detector, interrupting its alarm.
In rooms where temperatures may fall below 5oC or rise above 45oC.
In extremely dusty, dirty, or insect-infested areas where loose particles interfere with wireless smoke detector operation.
ATTENTION: Incorrect placement will result in a decrease of operational effectiveness.
MANUAL ELDES ESIM264 V3.1
EN
145
32.9.3.Installation
1. Detach the mounting plate by turning it counter-clockwise from
the back of EWF1 (see Fig. No. 88).
2. Secure the mounting plate to ceiling or wall with mounting
screws.(see Fig. No. 88).
3. Lift to open the battery pocket door (see Fig. No. 88).
4. Insert the battery into the battery pocket considering the polarity terminals indicated on the enclosure of EWF1. Ensure the
battery is securely connected. Red LED may flash briefly when
the battery is being installed.
5. Close the battery pocket door by snapping it into place.
6. Position the smoke detector to the mounting plate by turning
it clockwise to lock into place. Note that the device will not lock
into the mounting plate without the battery being present in
the battery pocket.
7. 7. Push the TEST button to verify if the wirless smoke detector is
operational. See 32.9.5.1. Testing EWF1.
8. Bind the device to the alarm system by sending a corresponding
command via SMS text message or using ELDES Configuration
Tool software. Please, refer to the software‘s HELP section or
refer to 19.1. Binding, Removing and Replacing Wireless
Devices for more details.
6. The system automatically informs about successful/unsuccessful binding process. If attempt to bind is unsuccessful, try to
move EWF1 closer to alarm system device and bind it again.
10. EWF1 wireless smoke detector is ready for use.
88
Mounting plate
Mounting slot
Screws
Battery pocket door
NOTE: If you are unable to bind the wireless device, please restore the parameters of the wireless device to default and try again. See chapter 32.9.6. Restoring Default Parameters for more details.
32.9.4.Interconnection
The interconnection feature automatically links all wireless smoke detectors resulting in causing an instant alarm in the system along
with the rest of EWF1 wireless smoke detectors. For more details on interconnection feature and how to manage it, please refer to 20.4.
EWF1 Interconnection.
32.9.5.Maintenance
32.9.5.1.Testing EWF1
•
The TEST button verifies if EWF1 is operational. Firmly push the TEST button and the wireless smoke detector will sound a loud beep.
The alarm will stop sounding after releasing the TEST button. When testing EWF1 using ELDES Configuration Tool software, the
detector will provide short beeps.
•
Stand at arm’s length from the wireless smoke detector when testing.
•
Test wireless smoke detectors weekly and upon returning from vacation or when no one has been in the household for several days.
•
Test each wireless smoke detector to be sure it is installed correctly and operating properly.
•
DO NOT use an open flame to test this wireless smoke detector. You may ignite and dam­age the wireless smoke detector or your
home.
•
If the wireless smoke detector does not sound, please check the battery and signal level using ELDES Configuration Tool software.
ATTENTION: Test all wireless smoke detectors weekly to ensure proper operation.
146
EN
MANUAL ELDES ESIM264 V3.1
32.9.5.2.Battery Replacement
1. Turn EWF1 counter-clockwise to detach it from the mounting
plate.
89
2. Gently pull down the wireless smoke detector.
9V battery
3. Remove the old battery from the battery pocket.
4. Postition the new 9V battery according to the appropriate
battery slot positive/negative terminals indicated on the
enclosure of EWF1. Ensure the plastic battery holder is fully
depressed when the battery has been fitted.
5. Using the TEST button, test the wireless smoke detector to
verify if it is operational. See 32.9.5.1. Testing EWF1.
6. Re-attach the wireless smoke detector to the mounting plate
by turning the wireless smoke detector clockwise until it snaps
into place.
ATTENTION: Only 9V 6F22 primary alkaline type battery can be used. Install only new, high quality and unexpired batteries.
ATTENTION: The battery must be removed if the device is not in use.
ATTENTION: In order to avoid fire or explosion hazards, the system must be used only with approved battery. Special care must be taken
when connecting positive and negative battery terminals. Dispose old batteries only into special collection sites. Do not charge, disassemble,
heat or incinerate old batteries.
NOTE: The battery status can be monitored in real-time using ELDES Configuration Tool software.
NOTE: The system sends an SMS message to the preset user phone number as soon as the battery level runs below 5%.
32.9.6. Restoring Default Parameters
1. Remove the battery from EWF1.
2. Press and hold the RESET button.
3. Insert the battery back to EWF1.
4. Hold the RESET button until you hear a short beep.
5. Release the RESET button.
On some EWF1 models the RESET button is not available. On such EWF1 devices the reset process is as follows:
1. Remove the battery from EWF1.
2. Wait for 1 minute or more.
3. Press and hold the TEST button.
4. Insert the battery back to EWF1.
5. Hold the TEST button for 10 seconds or more.
6. Release the TEST button.
ATTENTION: EWF1 built-in speaker will sound while pressing and holding the TEST button. Please, ignore the sound.
32.9.7. Cleaning
Clean the wireless smoke detector at least once a month to remove dust, dirt, or debris. Using the soft brush or wand attachment of a
vacuum cleaner, vacuum all sides and cover of wireless smoke detector. Be sure all the vents are free of debris.
If necessary, use a damp cloth to clean wireless smoke detector cover.
NOTE: Do not attempt to remove the cover to clean inside the wireless smoke detector. This will void your warranty.
MANUAL ELDES ESIM264 V3.1
EN
147
32.10. EWK2 - Wireless Keyfob
Main EWK2 features:
• Alarm system arming & disarming;
• Panic button;
• PGM output control;
• Sound indication by built-in mini buzzer;
• Visual indication by built-in LED indicator.
EWK2 is a wireless device intended to remotely arm and disarm ELDES alarm system, cause system alarm or to control any electric appliance connected to the alarm system’s PGM output. In order to start using wireless keyfob EWK2, it has to be bound to ELDES wireless
alarm system using ELDES Configuration Tool software or sending a corresponding SMS command. EWK2 keyfob features four configurable
buttons intended to operate according to individual needs. After the button is pressed, EWK2 internal buzzer’s sound signal and red LED
indicator confirms a transferred command to ELDES alarm system via wireless connection. The status of the sent command can be checked
by attempting to receive the feedback signal from the alarm system. This can be performed by pressing down the same button again and
holding it for 3 seconds. 3 short sound signals and LED indicator flashes indicate a successfully carried out command, while 1 long beep and
LED indicator flash stands for failed command and feedback signal failure. By default, one pair of buttons is already configured to arm and
disarm the alarm system. It is possible to connect up to 5 EWK2 devices to ELDES alarm system at a time. The maximum wireless connection
range is 150 meters (in open areas).
32.10.1. Technical Specifications
LED
indicator
90
Arm the
system
Disarm the
system
Optional
functionality
Optional
functionality
NOTE: Figure reflects the default EWK2 button configuration. All keyfob buttons are configurable according to individual needs.
148
EN
MANUAL ELDES ESIM264 V3.1
32.10.1.1. Electrical & Mechanical Characteristics
Battery Type
CR2032 Lithium
Battery Voltage; Capacity
3V; 240 mAh
Quantity of Batteries
1
Battery Operation Time
~18 months*
Wireless Transmitter-Receiver Frequency
868 Mhz
Range of Operating Temperatures
-20...+55ºC
Humidity
0-90% RH @ 0... +40 °C (non-condensing)
Dimensions
53 x 37 x 10 mm
Wireless Communication Range
Up to 30 meters in premises; up to 150 meters
in open areas
Compatible with Alarm Systems
ELDES Wireless
* The operation time depends on different conditions and may vary.
32.10.2. Installation
1. Open the EWK2 enclosure. Detach the front side of the enclosure by pulling the front side down
91
2. Once the enclosure is opened, remove the PCB from the EWK2 enclosure and flip the PCB so that the back side would be facing up.
92
93
3. Insert the CR2032 type battery provided in the EWK2 package. Before inserting the battery, ensure that it is positioned plus-marked
side up.
94
BATTERY
CR2032
+
MANUAL ELDES ESIM264 V3.1
EN
149
4. Insert the PCB back to the enclosure and close it.
5. Bind the device to the alarm system by sending a corresponding command via SMS text message or using ELDES Configuration Tool
soft­ware. Please, refer to the software‘s HELP section or refer to 19.1. Binding, Removing and Replacing Wireless Devices for
more details.
6. While binding the device to the alarm system, press any EWK2 button several times.
7. EWK2 is ready for use.
NOTE: If you are unable to bind the wireless device, please, restore the parameters of the wireless device to default and try again. See
chapter 32.10.5. Restoring Default Parameters for more details.
32.10.3. EWK2 Zones (Panic Button)
EWK2 keyfob supports a Panic Button feature allowing to cause alarm at any time when the specified button is pressed. This feature can
be configured using ELDES Configuration Tool by creating a virtual zone of Panic/Silent or 24-Hour type and assigning it to Virtual Alarm
option. The Panic Button feature can be set up on any button of EWK2.
32.10.4. Battery Replacement
1. Open EWK2 enclosure.
2. Remove the old battery from the battery slot.
3. Postition the new battery according to the appropriate battery slot positive terminal indicated.
4. Insert the battery into the battery slot.
5. Battery replaced.
See 32.10.2. Installation for more details.
ATTENTION: Only CR2032 3V battery can be used. Install only new, high quality and unexpired batteries.
ATTENTION: The battery must be removed if the device is not in use.
ATTENTION: In order to avoid fire or explosion hazards, the system must be used only with approved battery. Special care must be
taken when connecting positive and negative battery terminals. Dispose old batteries only into special collection sites. Do not charge,
disassemble, heat or incinerate old batteries.
NOTE: The system sends an SMS message to a preset User 1 as soon as the battery level runs below 5%.
NOTE: The battery status can be monitored in real-time using ELDES Configuration Tool software.
32.10.5. Restoring Default Parameters
1. Press and hold
and
buttons simultaneously.
2. Hold the buttons pressed until LED indicator and the buzzer provide several short flashes and beeps simultaneously.
3. Release the buttons.
4. Parameters restored to default.
150
EN
MANUAL ELDES ESIM264 V3.1
32.11. EWD2 - Wireless Door Contact/Shock Sensor/Water Sensor
Main EWD2 features:
•
Built-in shock sensor
•
2 wireless zones
•
Available zone modes: magnetic door contact, shock sensor, water sensor, digital sensor
•
2 built-in tamper switches: on the front and on the back of the PCB
EWD2 is a wireless device intended to secure doors, windows or any other opening/clsoing mechanisms. In addition, the device comes
equiped with a built-in shock sensor for vibration detection, an on-board zone terminal designed for external digital sensor or water sensor
connection and 2 built-in tamper switches for EWD2 sabotage detection. In order to start using EWD2, it has to be bound to ELDES alarm
system using ELDES Configuration Tool software or by sending a corresponding SMS text message to ELDES alarm system.
It is possible to connect up to 16 EWD2 devices to ESIM264 alarm system. The maximum wireless connection range is 150 meters (in open
areas).
32.11.1. Technical Specifications
32.11.1.1. Electrical and Mechanical Characteristics
Batteries
1,5V Alkaline AAAA type, LR8 (IEC standard) / 25A (ANSI/NEDA standard)
Number of Batteries
2
Battery Operation Time
~18 months*
Wireless Transmitter-Receiver Frequency
868 Mhz (EU version) / 915 Mhz (US version)
Wireless Communication Range
Up to 30 meters in premises; up to 150 meters in open areas
Range of Operating Temperatures
-20...+55ºC
Humidity
0-90% RH @ 0... +40 °C (non-condensing)
EWD2 Dimensions
101 x 22 x 20 mm
Magnet Dimensions
47 x 17 x 10 mm
Compatible with Alarm Systems
ELDES Wireless
* The operation time depends on different conditions and may vary.
32.11.1.2.
Main Unit and LED Functionality
95 FRONT SIDE
+
Z
COM
+
TAMP1
-
RESET
LED
DETECT
BACK SIDE
TAMP2
DETECT
ATTENTION FOR EWD2 v1 AND EWD2 v2: If no sensor is to be connected to EWD2 on-board zone terminal, please make a short-circuit (connect) Z and COM terminals in order to avoid the unnecessary battery power usage.
MANUAL ELDES ESIM264 V3.1
EN
151
Unit
Description
Z
Zone terminal
COM
Common terminal
TAMP1
Tamper switch
+/-
Battery slots
DETECT Magnet detector
LED
Light-emitting diode for indication of parameter restoring to default
RESET
Button for restoring default parameters
TAMP2
Tamper switch
32.11.2. Installation
1. Remove the cover of EWD2 enclosure.
96
97
Press and hold
Insert a screwdriver or
any other tool and push it down
2. Remove the PCB (printed-circuit-board) from the enclosure.
98
a) Press and hold
b) Pull up the edge
of the PCB
3. Screw in the enclsoure to the door or window jamb.
99
MOUNTING POINT A
MOUNTING POINT B
Ensure to screw in properly for supervision
of the back side by tamper switch
4. Wire up the external digital sensor (if any) or water sensor (if any) to Z and COM terminals, otherwise do not perform any wiring.
5.
152
Insert the PCB back into the enclosure
EN
MANUAL ELDES ESIM264 V3.1
100
101
102
6. Remove the cover of the magnet enclosure.
103
b) Pull up here
a) Insert a screwdriver or any
other tool and push it down
7. Screw in the magnet to the door or window frame and ensure that the magnet is fixed at the same height as the EWD2 magnet detector.
104
105
+
-
+
RESET
LED
20 mm max
8. Cover the magnet. No tools are required for this action.
9. Remove the plastic tab inserted between one of the battery terminals and battery slots of EWD2.
106
10. Close EWD2 enclosure using the cover. No tools are required for this action.
MANUAL ELDES ESIM264 V3.1
EN
153
11. Bind the device to the alarm system by sending a corresponding command via SMS text message or using ELDES Configuration Tool
software. Please, refer to the software‘s HELP section or refer to 19.1. Binding, Removing and Replacing Wireless Devices for
more details.
12. The system automatically informs about successful/unsuccessful binding process. If attempt to bind is unsuccessful, try to move EWD2
closer to alarm system device and bind it again.
13. EWD2 is ready for use.
ATTENTION: Ensure that EWD2 device is properly fixed to the wall and the Mounting Point B portrayed in Fig. No. 99 is properly screwed in.
Otherwise, the tamper switch will NOT supervise the back side of EWD2 enclosure (see also 32.11.3. EWD2 Zones and Tampers).
NOTE: If you are unable to bind the wireless device, please, restore the parameters of the wireless device to default and try again. See
31.11.5. Restoring Default Parameters for more details.
32.11.3. EWD2 Zones and Tampers
Upon successful EWD2 magnetic door contact binding process, the system adds 2 wireless Instant zones. The wireless zones can be set up
to operate under one of the following modes each:
•
•
Zone 1:
•
Magnetic door contact – Designed for causing an alarm (by default) if doors/windows are opened when the system is armed.
•
External sensor – Designed for causing an alarm (by default) if the wired digital sensor, connected to Z and COM terminals, is
triggered when the system is armed. This mode does NOT operate with Water sensor mode on Zone 2 simultaneously.
Zone 2:
•
Shock sensor – Designed for causing an alarm (by default) if the built-in shock sensor is triggered.
Possible zone mode combinations:
•
Zone 1: Magnetic door contact + Zone 2: Shock sensor
•
Zone 1: External Sensor + Zone 2: Shock sensor
•
Zone 1: Magnetic door contact + Zone2: N/A
•
Zone 1: External Sensor + Zone2: N/A
•
Zone 1: N/A + Zone 2: Shock sensor
NOTE: Water sensor mode is not supported when EWD2 is used with ESIM264 alarm system.
In case of tamper violation, the alarm is caused regardless of system being armed or disarmed. There are 2 ways to detect tamper violation
on EWD2:
•
By tamper switch. EWD2 comes equipped with 2 built-in tamper switches intended for enclosure supervision:
•
one located on the front side of the PCB supervising the front cover in case it is illegally opened (see Fig. No. 95).
•
the other one located on back of the PCB supervising the back side of the enclosure in case the EWD2 is illegally detached from
the wall (see Fig. No. 95).
Once the enclosure of EWD2 is tampered, the tamper switch will become triggered. This action will be followed by alarm, resulting in
sending an SMS text message and/or phone call to the user. The SMS text message contains the violated tamper number.
•
By wireless connection loss. The wireless connection loss between EWD2 and ESIM264 system leads to alarm. The system
identifies this event as a tamper violation and sends alarm by SMS text message and phone call to the user (-s) by default. The SMS
text message contains the violated tamper number and a star * character indicating wireless connection loss as a tamper alarm cause.
ATTENTION: The tamper will not operate if both wireless zones are disabled.
For more details on EWD2 zone and tamper configuration, please refer to ELDES Configuration Tool software’s HELP section.
32.11.4. Battery Replacement
1. Open EWD2 enclosure.
2. Remove both old batteries from the battery slots.
3. Insert the 2 new 1,5V Alkaline AAAA type batteries according to the appropriate battery slot positive/negative terminals indicated on
the PCB of EWD2.
4. Batteries replaced.
See 32.11.2. Installation for more details.
154
EN
MANUAL ELDES ESIM264 V3.1
ATTENTION: Only 1,5V Alkaline AAAA type batteries can be used. Install only new, high quality and unexpired batteries. Do not mix the old
batteries with the new ones.
ATTENTION: At least 1 battery must be removed if the device is not in use.
ATTENTION: In order to avoid fire or explosion hazards, the system must be used only with approved battery. Special care must be taken
when connecting positive and negative battery terminals. Dispose old batteries only into special collection sites. Do not charge, disassemble,
heat or incinerate old batteries.
ATTENTION: The system sends an SMS message to a preset user phone number as soon as the battery level runs below 5%.
ATTENTION: The battery status can be monitored in real-time using ELDES Configuration Tool software.
32.11.5. Restoring Default Parameters
1. Remove any battery from EWD2.
2. Press and hold the RESET button.
3. Insert the battery back to EWD2.
4. Hold the RESET button until LED indicator provides several short flashes.
5. Release the RESET button.
6. Parameters restored to default.
32.12. EWS3 - Wireless Indoor Siren
Main features:
• Audio alarm indication by 2 built-in speakers.
• Visual alarm indication by built-in LED indicators: burglary/24-hour/tamper alarm and fire alarm indicated in different colours.
• 2 tamper switches: for enclosure opening and device detachment from the wall detection.
EWS3 is a wireless indoor device with built-in siren speakers and LED indicators operating with ELDES wireless alarm systems. The device is designed to notify the user by audio and visual signals in the event of alarm as well as in event of system arming/disarming (Bell
Squawk feature must be enabled). In the event of burglary, 24-hour or tamper alarm, EWS3 will activate the speakers and flash the blue
LED indicators, while in case of a fire alarm, the device can flash the red LED indicator (both features require EWS3 Alarm LED and EWS3
Fire Alarm LED parameters to be enabled using ELDES Configuration Tool software or EKB2/EKB3 keypad)
To start using EWS3, it has to be bind to ELDES alarm system by sending a corresponding SMS message or using software ELDES Configuration Tool. Upon successful EWS3 binding process, the system adds one wireless zone and one wireless PGM output. In case of alarm,
the siren provides a sound alarm for one minute. The configuration of this parameter is disabled for EWS3 in order to save the battery
power.
It is possible to connect up to 16 EWS3 devices to ESIM264 alarm system. The maximum wireless connection range is 150 meters (in open
areas).
32.12.1. Technical Specifications
32.12.1.1. Electrical & Mechanical Characteristics
Battery Type
1,5V Alkaline AA type
Number of Batteries
4
Battery Operation Time
~18 months*
Wireless Transmitter-Receiver Frequency
868 Mhz
Rangeof Operating Temperatures
-25...+55ºC
Humidity
0-90% RH @ 0... +40 °C (non-condensing)
Dimensions
167 x 80 x 34 mm
Wireless Communication Range
Up to 30 meters in premises; up to 150 meters in open areas
Compatible with Alarm Systems
ELDES Wireless
Acoustic Sound Level
~90 dB measured at 1 m
* The operation time might vary in different conditions.
MANUAL ELDES ESIM264 V3.1
EN
155
32.12.1.2. Main Unit, LED & Connector Functionality
+
FRONT SIDE of PCB
-
BATTERY
+
+
BATTERY
-
-
BATTERY
+
107
TAMPER
TAMPER
BUZZER
-
BATTERY
BUZZER
BACK SIDE of PCB
STATUS
ALARM (blue)
RESET
ALARM (red)
ALARM (blue)
RESET
Button for restoring default parameters
+/-
Battery slots
STATUS
LED indicator for data transmission indication
ALARM (blue)
Blue LED indicators for visual alarm indication
ALARM (red)
Red LED indicator for visual alarm indication
BUZZER
Speakers for audio alarm indication
TAMPER
Tamper switches
FRONT SIDE of ENCLOSURE
108
ALARM (blue)
ALARM (red)
ALARM (blue)
LED indication
Description
ALARM (blue) flashing
Burglary, 24-Hour or tamper alarm in progress
ALARM (red) flashing
Fire alarm in progress
32.12.2. Installation
1. open EWS3 enclosure.
109
a. Press and hold
b. Pull down
2. Once the enclosure is opened, fix the siren to the wall using the screws.
156
EN
MANUAL ELDES ESIM264 V3.1
MOUNTING POINT B
MOUNTING POINT A
-
+
+
-
-
+
111
MOUNTING POINT A
Ensure to screw in properly for supervision of the back side by tamper switch
-
+
110
MOUNTING
POINT B
3. Remove the plastic tab inserted between one of the battery terminals and battery slot contacts.
The wireless connection loss between EWS3 and ELDES alarm system leads to alarm. The system identifies this event as a tamper violation and sends an alarm by SMS text message and phone call to the user (-s) by default. The SMS
message contains the wireless device model, wireless ID code and tamper number.
112
4. STATUS indicator should start flashing indicating successful data transmission.
5. Close EWS3 enclosure by putting the cover back.
6. Bind the device to the alarm system by sending a corresponding command via SMS text message or using ELDES Configuration Tool
software. Please, refer to the software‘s HELP section or refer to 19.1. Binding, Removing and Replacing Wireless Devices for
more details.
7. The system automatically informs about successful/unsuccessful binding process. If attempt to bind is unsuccessful, try to move
EWS3 closer to alarm system device and bind it again.
ATTENTION: Ensure that EWS3 device is properly fixed to the wall and the Mounting Point A portrayed in Fig. No. 110 and Fig. No. 111
is properly screwed in. Otherwise, the tamper switch will NOT supervise the back side of EWS3 enclosure (see also 33.12.3. EWS3
Zone, PGM Output and Tamper).
NOTE: If you are unable to bind the wireless device, please, restore the parameters of the wireless device to default and try again.
See chapter 33.12.5. Restoring Default Parameters for more details.
32.12.3. EWS3 Zone, PGM Output and Tamper
Upon successful EWS3 outdoor siren binding process,the system adds 1 wireless Instant zone and 1 wireless Siren PGM output. The
wireless zone is intended for EWS3 tamper control and ability to assign a partition (-s), while the wireless PGM output is intended for siren
speaker control.
In case of tamper violation, the alarm is caused regardless of system being armed or disarmed. There are 2 ways to detect tamper violation on EWS3:
• By tamper switch. EWS3 comes equipped with 2 built-in tamper switches intended for enclosure supervision:
• one located on the front side of the PCB supervising the front cover in case it is illegally opened (see Fig. No. 107).
• the other one located on back of the PCB supervising the back side of the enclosure in case the EWS3 is illegally detached from the
wall (see Fig. No. 107).
Once the enclosure of EWS3 is tampered, the tamper switch will become triggered. This action will be followed by alarm, resulting in
sending an SMS text message and/or phone call to the user. The SMS text message contains the violated tamper number.
• By wireless connection loss. The wireless connection loss between EWS3 and ESIM264 system leads to alarm. The system identifies
this event as a tamper violation and sends alarm by SMS text message and phone call to the user (-s) by default. The SMS text message
contains the violated tamper number and a star * character indicating wireless connection loss as a tamper alarm cause.
ATTENTION: The tamper will not operate if the wireless zone is disabled.
MANUAL ELDES ESIM264 V3.1
EN
157
32.12.4. Battery replacement
1.
open EWS3 enclosure.
2.
Remove all 4 old batteries from the battery slots.
3.
Postition the 4 new 1,5V alkaline AA type batteries according to the appropriate battery slot positive/negative terminals indicated
on the PCB (printed-circuit-board) of EWS3
4.
Insert the batteries into the battery slots.
5.
Batteries replaced.
See chapter 33.12.2. Installation for more details.
ATTENTION: Only 1,5V Alkaline AA type batteries can be used. Install only new, high quality and unexpired batteries. Do not mix the
old batteries with the new ones.
ATTENTION: At least 1 battery must be removed if the device is not in use.
ATTENTION: In order to avoid fire or explosion hazards, the system must be used only with approved battery. Special care must be
taken when connecting positive and negative battery terminals. Dispose old batteries only into special collection sites. Do not charge,
disassemble, heat or incinerate old batteries.
NOTE: The system sends an SMS message to a preset user phone number as soon as the battery level runs below 5%.
NOTE: The battery status can be monitored in real-time using ELDES Configuration Tool software.
32.12.5. Restoring default parameters
1. Remove one battery from EWS3.
2. Press and hold the RESET button.
3. Insert the battery back to EWS3.
4. Hold the RESET button until LED indicator starts blinking.
5. Release the RESET button.
6. Parameters reset to default.
158
EN
MANUAL ELDES ESIM264 V3.1
33.REMOTE SYSTEM RESTART
In some critical situations, a system restart may be required. To remotely carry out system restart, please refer to the following configuration method.
Restart the system
MANUAL ELDES ESIM264 V3.1
SMS
SMS text message content:
ssss_RESET
Value: ssss – 4-digit SMS password.
Example: 1111_RESET
EN
159
34.TECHNICAL SUPPORT
34.1.Troubleshooting
Indication
Possible reason
Indicator STAT is off
· No main power supply
· Wiring done improperly
· Blown fuse
Indicator NETW is off or flashing
·
·
·
·
·
·
·
Missing SIM card
PIN code is enabled
SIM card is inactive
Disconnected antenna
GSM network signal too weak
Problems with GSM provider
Microcontroller is not started due to electrical mains noise or static discharge
System does not send any SMS text messages
and/or does not ring
·
·
·
·
·
SIM card credit balance depleted
Incorrect SMS centre phone number
No GSM network signal
User number is not added (or control from anu phone number is disabled)
SIM card changed before disconnecting main power supply or backup battery
Received SMS text message “Wrong syntax”
· Incorrect SMS text message structure
· Extra space symbol could be left in SMS text message
Missing temperature indication in Info SMS text
message/EKB2 keypad
· Temperature sensor not connected
· Temperature sensor broken
· Connection wires too long
24H and/or Fire zones do not work
· Specified zone must be enabled by SMS, ELDES Configuration Tool, EKB2 or EKB3
keypad.
No sound during remote listening
· Microphone not connected
· Improper microphone connection
For product warranty repair service please , contact your local retail store where this product was purchased.
If your problem could not be fixed by the self-guide above, please contact your local distributor. More up to date information about your device and other products can be found at the manufacturer’s website www.eldes.lt
34.2.Restoring Default Parameters
1. 2. 3. 4. 5. 6. Disconnect the power supply and backup battery.
Short circuit (connect) DEF pins.
Power up the device for 7 seconds.
Power down the device.
Remove short circuit from DEF pins.
Parameters restored to default.
34.3. Updating the Firmware via USB Cable Locally
1. Disconnect the power supply and backup battery.
2. Short circuit (connect) DEF pins.
3. Connect the device via USB cable to the PC.
4. Power up the device.
5. The new window must pop-up where you will find the .bin file. Otherwise open My Computer and look for Boot Disk drive.
6. Delete the .bin file found in the drive.
7. Copy the new firmware .bin file to the very same window.
8. Power down the device.
9. Unplug USB cable.
10. Remove short circuit from DEF pins.
11. Power up the device.
12. Firmware updated.
NOTE: It is strongly recommended to restore default parameters after the firmware update.
160
EN
MANUAL ELDES ESIM264 V3.1
34.4.Updating Firmware via GPRS Connection Remotely
ATTENTION: The system will NOT send any data to monitoring station while updating the firmware remotely via GPRS network. However, during the firmware update process, the data messages are queued up and transmitted to the monitoring station after the firmware
upgrade process is over.
Before updating the firmware remotely via GPRS connection, make sure that:
• SIM card is inserted into SIM CARD slot of Esim264 device (see 2.2. Main Unit, LED & Connector Functionality).
• Mobile internet service (GPRS) is enabled on the SIM card.
• Power supply is connected to ESIM264.
• Default SMS password is changed to a new 4-digit password (see 6. PASSWORDS).
• At least User 1 phone number is set up (see 8. USER PHONE NUMBERS).
• APN, user name and password are set up (see 30.2.1. GPRS Network).
Initiate FOTA
ESIM264 alarm system supports FOTA (firmware-over-the-air) feature. This allows to upgrade the firmware remotely via GPRS connection. Once the upgrade process is initiated, the system connects to the
specified FTP server address where the firmware file is hosted and begins downloading and re-flashing
the firmware. The firmware file must be located in a folder titled Firmware. In order to initiate the upgrade process please , send the following SMS message.
SMS
SMS text message content:
XXXX_FOTA:ftp-server-ip,port,firmware-file-name.bin,user-name,password
Value: ssss - 4-digit SMS password; ftp-server-io - public IP address of FTP server where
EPIR firmware file is stored; port - port number of FTP server (usually - 21); firmware-filename.bin - name of the firmware file, allowed max. length - up to 31 character; user-name
- user name of FTP server login, allowed max. length - up to 31 character; password password of FTP server login, allowed max. length - up to 31 character.
Example: 1111_FOTA:84.15.143.111,21,ESIM264fw bin,eldesuser,eldespassword
ATTENTION: Comma character is NOT allowed to use in user name and firmware file name.
ATTENTION: “ELDES UAB” does not run a FTP server and does not host the firmware files online. Please, contact your local distributor to
request the latest firmware file: support@eldes.lt
NOTE: It is strongly recommended to restore default parameters after the firmware update.
MANUAL ELDES ESIM264 V3.1
EN
161
34.5.Frequently Asked Questions
Question
Answer
Yes, ESIM264 device can fully operate without any SIM card inserted. In this case
1. Can ESIM264 operate as standalone device without SIM
you will not be able to configure and control the device by SMS and calls nor to
card inserted?
receive any SMS reports and calls.
Due to security reasons it is recommended to restore the violated zone (-s)
2. I am unable to arm the alarm system when one of the
before arming the alarm system. However, you can enable a Force attribute
zones (some zones) is violated, although I was able
or use the Bypass feature in order to arm the alarm system despite the vioto perform disarming. Is there a way to arm the alarm
lated zone (-s) being present. Please, refer to 14.5. Zone Type Definitions
system while the zone is violated?
and 14.7. Bypassing and Activating Zones.
3. I have activated ATZ mode in ELDES Configuration Tool
It appears that your ELDES Configuration Tool software is outdated. Please,
software, but I am unable to set the connection Type 5.
download the latest ELDES Configuration Tool software version by visiting
Whenever I select Type 5 and press the “Write Settings”
www.eldes.lt/en/download.
button it switches back to Type 4. What’s wrong?
4. When ESIM264 fully powers down my configuration
This might have happened due to the jumper left on DEF pins or it is a hardbecomes lost and I have to re-configure the device
ware failure. Please, remove the jumper if it is present on DEF pins or contact
again. What’s wrong?
your supplier for warranty service.
If the smoke detector is connected to one of the Esim264 PGM outputs
5. I have a smoke detector connected to ESIM264 system. you can reset it by turning the PGM output OFF and then back ON. This
How do I reset the smoke detector when the “Fire” zone can be performed by SMS, EKB2 keypad, EKB3 keypad and ELDES Configuis violated?
ration Tool software. Please, refer to 18.4. Turning PGM Outputs ON and
OFF.
6. What happens if I switch backup battery pole terminals Switching backup battery pole terminals places is forbidden. Otherwise this
places?
will lead to blown fuse and ESIM264 alarm system will have to be repaired.
The SMS reports on tamper violation can be disabled by EKB2, EKB3 keypads
7. How do I disable SMS reports and calls in case of tamper
or ELDES Configuration Tool software. For mor details, please refer to 16.
violation when alarm system is disarmed?
TAMPERS or to the software’s HELP section. However, due to security
reasons it is not recommended to disable this feature.
8. Is any additional configuration necessary when conNo additional configuration is required in order to make EPGM1 module
necting EPGM1 module after wiring is done accroding to
operational.
EPGM1 user manual?
No, the number of EPGM1 zones does not duplicate in ATZ mode as
9. Does the number of EPGM1 zones duplicate when ATZ
EPGM1 module does not support ATZ mode. Only ESIM264 zones
mode is activated in the system?
duplicate in ATZ mode.
10. I connect the wired siren to ESIM264 and I hear a silent
sound alarm even when the alarm system is disarmed.
Please, connect the resistor of 3,3 kΩ nominal to the BELL- / BELL+ contacts
In case of alarm system alarm the siren provides a loud
This should solve the problem.
sound alarm as it should. Why?
11. I am using Windows operating system. The windows
Please, update ELDES Configuration Tool software by visiting www.eldes.lt/
of ELDES Configuration Tool are not fully displayed and
en/download and downloading the latest version.
some parts are like cut-off. What’s wrong?
12. The buzzer remains active when I disarm the alarm
The buzzer is intended for iButton indication only and it is not related to
system using the keypad. Why?
disarming process by keypad.
This happens due to wireless connection loss. There might be several reasons:
1. ELDES wireless device is installed too close or too far from ESIM264
13. One of wireless devices connected to ESIM264 system
system.
sends a tamper alarm from time to time, although no
2. Interference of other electronic equipment.
tamper was violated. Why?
3. Physical interference (building walls, floors etc.)
4. Metal material interference.
14. I have connected a wired magnetic door sensor, but
This happens due to incorrect resistor connection. Please, refer to correI receive tamper alarm instead of zone alarm. What’s
sponding connection circuit according to the selected zone connection type
wrong?
(Type 1 – 5). See 2.3.2 Zone Connection Types for more details.
By default, this notification is enabled. The system checks the backup
15. I disconnected the backup battery, but did not receive
battery resistance once a day and sends an SMS report to User 1 on backup
any SMS report on this event. How do I enable SMS
battery replacement if more than 2Ω resistance is detected. For more details,
report on backup battery disconnection?
please refer to 21. BACKUP BATTERY, MAINS POWER SUPPLY STATUS
MONITORING AND MEMORY.
162
EN
MANUAL ELDES ESIM264 V3.1
Question
Answer
Every time an SMS text message is sent to the user, the system must “know”
that the message was successfully delivered. The only way to partly disable the
16. When I check system SIM card credit balance I see a lot
SMS delivery report (for alarm notifications only) is to enable alarm SMS notificaof SMS delivery confirmation reports. How do I disable
tions to all users. This is useful when having only User1 phone number set up, as
SMS delivery confirmation ESIM264 system?
in case of alarm the system sends the alarm SMS text message to all preset users
simultaneously, but does not require any SMS delivery report.
According to GSM standards 1 SMS text message may consist of up to 160
17. I have set zone names and/or PGM output names
Latin alphabet/English characters maximum. If the message contains at
containing some Cyrillic and/or non-English characters. least one non-latin/non-English character, the length of SMS message beThe zone names and PGM output names do not fully fit comes at least half shorter, since those characters occupy more size of the
in the SMS message. What‘s wrong?
SMS text message than the Latin ones. It is recommended not to use any
non-Latin/ non-English characters in zone names and PGM output names.
18. The configuration of added wireless keyfob EWK1 to
ELDES Configuration Tool version is too old. Please, update it.
ESIM264 system is not visible in ELDES Configuration
Tool. What‘s wrong?
Microsoft .NET Framework v3.5 is not installed in Windows system. Please,
19. I am unable to run ELDES Configuration Tool - I receive
download this package from official Microsoft website free of charge and
error messages in Windows. Why?
install it to your Windows system.
20. Info SMS report comes with wrong date and time. How
do I correct it?
Please, set the correct system date and time using either ELDES Configura­
tion Tool, EKB2, EKB3 keypad or SMS text message.
It appears that the device is unable to establish a communication with
configuration / FTP server. Please, check the GPRS settings in ESIM264
configuration (APN, user name, password), the location of the firmware
21. I receive an error message when attempting to
..bin file (must be located in the FTP server folder titled Firmware) and
configure the device or update the firmware remotely.
the mobile internet feature presence on the SIM card used with ESIM264.
Whats wrong?
If this does not solve the problem, please contact your GSM operator (and
ISP - for remote configuration problems) in order to request a list of blocked
TCP ports.
1. Send the ssss_endconfig SMS text message.
22. I waited for at least 5 minutes, but did not receive any
2. In ELDES Configuration Tool software press Disconnect button and
SMS message confirming that remote configuration via
repeat the steps from the beginning as described in 5.1. Remote System
GPRS connection has stopped. What‘s wrong?
Configuration via GPRS Connection.
MANUAL ELDES ESIM264 V3.1
EN
163
35.RELATED PRODUCTS
164
EKB2 - LCD keypad
EKB3 - LED keypad
ME1 - metal cabinet
EPGM1 - hardwired zone and PGM output expansion module
EPGM8 - hardwired PGM output expansion module
EA1 - audio output module
EN
MANUAL ELDES ESIM264 V3.1
EA2 - audio output module with amplifier
DS1990A-F5 - iButton key
DS18S20 - temperature sensor
ED1T - plastic enclosure with iButton key reader
and temperature sensor
EWP1 - wireless PIR sensor (motion detector)
EWD1 - wireless magnetic door contact
MANUAL ELDES ESIM264 V3.1
EN
165
EWS2 - wireless external siren
EWS1 - wireless internal siren
EWK1 - wireless keyfob
EWF1 – wireless smoke detector
EW1 - wireless zone and PGM output expansion module
EW1B - battery-powered wireless zone and
PGM output expansion module
EWD2 - wireless door contact/shock sensor
166
EN
EWK2 - wireless keyfob
MANUAL ELDES ESIM264 V3.1
EWS3 - wireless indoor siren
MANUAL ELDES ESIM264 V3.1
EN
167
Made in the European Union
www.eldes.lt