671EX
OWNERS MANUAL
for
SS2 - SERIES
DUAL SATELLITE
COFFEE BREWERS
with
ELECTRO-MECHANICAL
CONTROL
and
EXTERNALLY HEATED
SATELLITE SERVERS
MODEL:
9221EX
Includes:
Installation
Operation
Use & Care
Servicing Instructions
Model 9221EX Dual Satellite Brewer
p/n 76624 Rev. B ECN-12664
M671EX
040405 cps
WARRANTY STATEMENT
It also does not apply if the serial nameplate has been
removed or unauthorized service personnel perform service.
The prices charged by Bloomfield Industries for its products
are based upon the limitations in this warranty. Seller’s
obligation under this warranty is limited to the repair of defects
without charge by a Bloomfield Industries Authorized Service
Agency or one of its sub-agencies. This service will be
provided on customer’s premises for non-portable models.
Portable models (a device with a cord and plug) must be
taken or shipped to the closest Authorized Service Agency,
transportation charges prepaid, for services.
All electrical equipment manufactured by BLOOMFIELD
INDUSTRIES is warranted against defects in materials and
workmanship for a period of one year from the date of original
installation or eighteen (18) months from the date of shipment
from our factory, whichever comes first, and is for the benefit
of the original purchaser, except that:
a. airpots carry a 30 day parts warranty only.
b. dispensers; i.e., tea and coffee carry a 90 days parts
warranty only, excludes decanters.
THE FOREGOING OBLIGATION IS EXPRESSLY GIVEN IN
LIEU OF ANY OTHER WARRANTIES, EXPRESSED OR
IMPLIED, INCLUDING ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE, WHICH ARE HEREBY EXCLUDED.
In addition to restrictions contained in this warranty, specific
limitations are shown below (Additional Warranty Exclusions).
Bloomfield Industries Authorized Service Agencies are located
in principal cities.
BLOOMFIELD INDUSTRIES DIVISION / SPECIALTY
EQUIPMENT MANUFACTURING CORPORATION SHALL
NOT BE LIABLE FOR INDIRECT, INCIDENTAL OR
CONSEQUENTIAL DAMAGES OR LOSSES FROM ANY
CAUSE WHATSOEVER.
This warranty is valid in the United States and void elsewhere.
Please consult your classified telephone directory or your food
service equipment dealer; or, for information and other details
concerning warranty, write to:
Service Parts Department
Bloomfield Industries
P.O. Box 280
Verdi, NV 89439
Phone: (775) 689-5700
Fax: (888) 492-2783
This warranty is void if it is determined that upon inspection by
an Authorized Service Agency that the equipment has been
modified, misused, misapplied, improperly installed, or
damaged in transit or by fire, flood or act of God.
SERVICE POLICY AND PROCEDURE GUIDE
ADDITIONAL WARRANTY EXCLUSIONS
1.
2.
3.
4.
5.
6.
7. Full use, care and maintenance instructions are supplied
with each machine. Those miscellaneous adjustments
noted are customer responsibility. Proper attention will
prolong the life of the machine.
8. Travel mileage is limited to sixty (60) miles from an
authorized Service Agency or one of its sub-agencies.
9. All labor shall be performed during normal working hours.
Overtime premium shall be charged to the customer.
10. All genuine Bloomfield replacement parts are warranted
for ninety (90) days from date of purchase on nonwarranted equipment.
Any use of non-genuine
Bloomfield parts completely voids any warranty.
11. Installation, labor and job check-out are not considered
warranty.
12. Charges incurred by delays, waiting time or operating
restrictions that hinder the service technicians ability
to perform services are not covered by warranty.
This includes institutional and correctional facilities.
Resetting of safety thermostats, circuit breakers,
overload protectors, or fuse replacements unless
warranted conditions are the cause.
All problems due to operation at voltages other than
specified on equipment nameplates; conversion to
correct voltage must be the customer’s responsibility.
All problems due to electrical connections not made in
accordance with electrical code requirements and
wiring diagrams supplied with the equipment.
Replacement of items subject to normal wear, to include
such items as knobs and light bulbs. Normal maintenance
functions including adjustment of thermostats, microswitches,
and replacement of fuses and indicating lights are not
covered under warranty.
All problems due to inadequate water supply, such as
fluctuating, or high or low water pressure.
All problems due to mineral/calcium deposits, or
contamination from chlorides/chlorines. De-liming is
considered a preventative maintenance function and is
not covered by warranty.
SHIPPING DAMAGE CLAIMS PROCEDURE
NOTE: For your protection, please note that equipment in
this shipment was carefully inspected and packaged by
skilled personnel before leaving the factory.
Upon acceptance of this shipment, the transportation
company assumes full responsibility for its safe delivery.
IF SHIPMENT ARRIVES DAMAGED:
1. VISIBLE LOSS OR DAMAGE: Be certain that any
visible loss or damage is noted on the freight bill
or express receipt, and that the note of loss or damage
is signed by the delivery person.
2. FILE CLAIM FOR DAMAGE IMMEDIATELY:
Regardless of the extent of the damage.
3.
CONCEALED LOSS OR DAMAGE: if damage is
unnoticed until the merchandise is unpacked, notify the
transportation company or carrier immediately, and file
“CONCEALED DAMAGE” claim with them. This
must be done within fifteen (15) days from the date the
delivery was made to you. Be sure to retain the
container for inspection.
Bloomfield Industries cannot assume liability for damage or
loss incurred in transit. We will, however, at your request,
supply you with the necessary documents to support your
claim.
xi
TABLE OF CONTENTS
WARRANTY STATEMENT
SPECIFICATIONS
FEATURES & OPERATING CONTROLS
PRECAUTIONS & GENERAL INFORMATION
AGENCY APPROVAL INFORMATION
INSTALLATION
OPERATION
CLEANING INSTRUCTIONS
PROGRAMMING INSTRUCTIONS
TROUBLESHOOTING SUGGESTIONS
SERVICING INSTRUCTIONS
EXPLODED VIEWS
WIRING DIAGRAM
SATELLITE
Thank You for purchasing this
Bloomfield Industries appliance.
xi
1
2
4
4
5
7
10
12
17
18
20
24
25
Proper installation, professional
operation and consistent
maintenance of this appliance will
ensure that it gives you the very
best performance and a long,
economical service life.
This manual contains the
information needed to properly
install this appliance, and to use,
care for and maintain or repair the
appliance in a manner which will
ensure its optimum performance.
SPECIFICATIONS
MODEL
VOLTS
3NAC
9221EX
380-415
WATTS
6250
1
AMPS
L3
L1
L2
8.7
8.7
9.8
N
1.1
HZ
50/60
FEATURES AND OPERATING CONTROLS
Fig 1. SS-2 Satellite Brewing System
Features & Operating Controls
2
FEATURES AND OPERATING CONTROLS (continued)
Brewer
Adjustable Legs
Allows brewer to be leveled. Also allow clearance for cleaning
underneath brewer.
Brewing Controls
Start or stop brew and select brew volume. Right and left section
are independent.
Bypass Nozzle
Dilution water flows into brew chamber channel from here.
Dilution water DOES NOT flow through the coffee grounds.
Heater Switch
Turns power to tank heater ON or OFF.
Hot Water Faucet
Hot water dispensed here.
Nameplate
Lists manufacturer, model and serial number.
Also lists voltage and wattage rating of brewer.
Ready-To-Brew Light
Glows when the tank water is up to temperature.
System Switch
(not shown)
Located on lower right rear of brewer. Turns main power to
brewer ON or OFF .
Satellite Locator/Warmer
Positions externally heated satellite on brewer. Maintains
temperature of product in satellite.
Warmer Switches
Control individual warmers for externally heated satellite .
Brew Chamber
Brew Chamber
Holds coffee grounds during brew cycle.
Bypass Diverter
Forms dilution flow channel by holding filter clear of the brew
chamber wall.
Satellite
Brew-Thru Lid
Allows entry of brewed coffee and dilution water into satellite.
Minimizes splashing in the event satellite is tipped.
Handles
Allow the satellite to be safely carried.
Nameplate
Lists manufacturer, model and serial number.
Also lists voltage and wattage rating of satellite.
Serving Faucet
Fresh coffee dispensed from satellite here.
Sight Glass
Check the level of coffee remaining here.
Drip Tray (optional)
Optional drip tray catches drips and spills from serving faucet.
Easily removed for cleaning.
3
GENERAL INFORMATION AND PRECAUTIONS
WARNING:
Electric
Shock hazard
All servicing requiring access
to non-insulated electrical
components must be
performed by a factory
authorized technician.
DO NOT open any access
panel which requires the use
of tools. Failure to follow this
warning can result in severe
electrical shock.
CAUTION:
Burn Hazard
This appliance is intended for use in commercial establishments
only.
This appliance is intended to brew hot beverage, specifically coffee,
for human consumption. No other use is recommended or authorized
by the manufacturer or its agents.
Operators of this appliance must be familiar with the appliance use,
limitations and associated restrictions. Operating instructions must be
read and understood by all persons using or installing this appliance.
Cleanliness of this appliance is essential to good sanitation. Read and
follow all included cleaning instructions and schedules to ensure the
safety of the food product.
Surfaces of the brewer, brew basket and satellite can be hot to the
touch, and may cause burns on contact.
Disconnect the brewer from electrical power before performing any
maintenance or servicing.
Surfaces of this brewer can
be hot and can cause burns
on contact.
DO NOT submerge satellites in water.
IMPORTANT !
Do not store any combustible
materials or flammable liquids
anywhere near the appliance.
Any procedure which requires the use of tools must be performed by a
qualified technician.
DO NOT splash or pour water over, onto or into any controls,
control panel or wiring.
This manual is considered to be a permanent part of the appliance.
This manual and all supplied instructions, diagrams, schematics, parts
breakdown illustrations, notices and labels must remain with the
appliance if it is sold or moved to another location.
This appliance is made in the USA. Unless otherwise noted, this
appliance has American sizes on all hardware.
AGENCY APPROVAL INFORMATION
This dual satellite brewing system meets
Standards
This dual satellite brewing system meets NSF Standard 4 only when
installed and maintained per the instructions in this manual.
STD 4
4
INSTALLATION INSTRUCTIONS
INSTALL LEGS & LEVEL THE UNIT
CAUTION:
The brewer is provided with 4" (100 mm) adjustable legs and
rubber feet. Be sure the legs are securely screwed into the base
of the brewer, and that the rubber feet are properly installed.
Hazard from
Unstable Equipment
The adjustable legs allow the brewer to be leveled. Set the brewer
in its ultimate operating location and check for level with a spirit
level Adjust the brewer for level from front-to-rear, and from sideto-side. Be sure all four feet rest firmly on the counter.
PLUMBER’S INSTALLATION INSTRUCTIONS
IMPORTANT:
Brewer must be installed on a potable water supply line with a
full-flow pressure between 20 psi (138 kPa) and 90 psi (620 kPa).
NOTE:
If water pressure varies greatly, or exceeds 90 psi (620 kPa) at
any time, a water pressure regulator must be installed. Plumbing
installer must supply the regulator.
Brewer must be connected to a potable water supply. Bloomfield
recommends not less than 1/4” (6 mm) inside diameter copper
tubing for installations of 12’ (4 meters) or less, and not less than
3/8” (10 mm) I.d. copper tubing for installations exceeding
12’ (4 meters).
Rubber feet must be installed
on each leg of the brewer.
Legs must be adjusted so that
all four feet rest firmly on the
counter. Failure to properly
install the feet can result in
movement of the brewer, which
can cause personal injury and/
or damage to the brewer.
SCREW INTO
BREWER
FRAME
ADJUST
FOR
HEIGHT
ATTACH
RUBBER
FEET
Fig. 2 Adjustable Leg
Brewer must be connected to a COLD water line.
NOTE: DO NOT use a saddle tap for this water line connection.
CAUTION:
A shut-off valve must be installed between the main water supply
and the brewer. Plumbing installer must supply the shut-off valve.
A 1/4-turn ball valve is recommended.
Electric Shock
Hazard
Flush the water line before connecting to the brewer.
Bloomfield highly recommends the use of the provided water
strainer to help prevent deposits in the brewing system.
5
Brewer must be properly
grounded to a reliable earth
ground to prevent possible
shock hazard. Do not assume
a plumbing line will provide
such a ground. Electrical shock
may cause serious injury.
INSTALLATION INSTRUCTIONS (continued)
IMPORTANT !
These installation instructions
are prepared for personnel
authorized, qualified, certified or
licensed to install electrical
equipment, who should perform
all initial startup and
adjustments.
IMPORTANT !
Do not store any combustible
materials or flammable liquids
anywhere near the appliance.
EUROPEAN ELECTRICAL INSTALLATION INSTRUCTIONS
IMPORTANT !
• Make sure the incoming voltage is the same voltage,
frequency and phase as specified on the appliance
nameplate. Connecting the appliance to the wrong voltage
may cause severe damage to internal components, or may
cause a severe decrease in performance.
IMPORTANT !
• An approved all pole power disconnect switch with at least a
3mm contact gap must be supplied and installed in the fixed
wiring in an accessible location (close proximity to the
appliance) by a licensed electrician. Refer to General Layout
Data sheet for electrical ratings.
SUPPLY CORDS
• Power supply cords should be oil-resistant, sheathed flexible
cable not lighter than ordinary polychloroprene or other
equivalent synthetic elastomer-sheathed cord (code
designation 245 IEC 57) or an approved metal conduit
connection.
• Minimum cross sectional area of conductors per line must be
1.5 square mm and total length not to exceed 2 meters
between supply connection and appliance. Supply wires
must be suitable for at least 90ºC temperature rating
• For flexible power cords, an approved strain relief fitting must
be supplied by others.
WIRING CONNECTIONS
• Using a screwdriver, remove rear panel.
• Knock out the appropriate hole plug and connect conduit
strain relief.
• Thread supply leads through strain relief and connect power
leads to terminals marked “L1”, “L2” & “L3”. Connect
neutral lead to terminal marked “N”.
• Connect ground lead (green with yellow stripe) to ground lug
marked “ ”.
• Secure all connections and reinstall terminal cover.
6
INSTALLATION INSTRUCTIONS (continued)
INITIAL SET-UP INSTRUCTIONS
Plumber’s and Electrician’s installation procedures must be
completed before proceeding with the set-up.
Be sure all electrical connections are secure, and that all
plumbing connections are secure and leak-proof.
1. CHECK BREWER FOR PROPER CONFIGURATION
Make sure spray disk gaskets are in place INSIDE of spray
heads.
Make sure spray disks are properly installed.
Check hot water faucet for proper operation and leaks.
Place empty satellites in position.
2. START BREWER OPERATION
Be sure HEATER ON/OFF switch is OFF, then press
POWER SWITCH on back of unit to energize brewer.
Water Inlet Solenoid will energize, filling the tank with water.
Fill time is approximately 13 minutes. Tank will fill until water
is sensed at the water level probe. Water level will be
maintained automatically once the tank is filled.
Press HEATER ON/OFF switch ON. Water in tank will heat
to brewing temperature in approximately 30 minutes. When
the water temperature reaches the brew temperature set
point, the READY-TO-BREW light will glow.
IMPORTANT:
Initial set-up must be performed
by a qualified installer or
qualified service technician.
Improper set-up will damage the
brewer and void the warranty.
IMPORTANT:
Complete water line installation
before connecting brewer to
electrical power.
MAKE SURE THE FRONT
PANEL "HEATER ON/OFF"
SWITCH IS IN THE OFF
POSITION BEFORE
CONNECTING BREWER TO
ELECTRICAL POWER.
DO NOT turn the HEATER ON/
OFF switch on until the water
tank is filled. Heating elements
must be completely submerged
in water at all times. Damage to
the brewer caused by operating
the heating elements dry is NOT
covered by warranty.
3. FINAL CHECKS
After initial heat-up and before brewing, draw water from the
hot water faucet until the inlet solenoid actuates. This will
prevent volume differences to the initial brew caused by
water expansion.
Press SATELLITE WARMER switch on. Brewer will not
operate unless the appropriate SATELLITE WARMER
switch on.
7
NOTE: Brewer will not operate
unless the appropriate
WARMER SWITCH is turned
ON.
OPERATING INSTRUCTIONS
Fig. 3 Control Panel
GETTING STARTED
Check the brewer and satellites:
Check that the brewer is clean and the drip tray (if used)
is empty.
Check that the satellites are empty and clean with lids
properly installed.
Check the spray heads:
Remove the brew chambers. Check the spray heads. Verify
that the spray disks are clean and properly installed. Verify
that the gaskets are properly installed inside the spray heads.
Check the brew chambers:
Check that the brew chamber is clean.
Check that the bypass diverters are properly installed in the
brew chambers.
START-UP
Press POWER SWITCH (back of brewer) to ON. Brewer water
tank will begin filling.
When tank stops filling, press HEATER ON/OFF switch to ON:
READY-TO-BREW light will glow when water is at proper
temperature for brewing.
Press SATELLITE WARMER switches to OFF until ready to
begin brewing.
8
OPERATING INSTRUCTIONS (continued)
Fig. 4 Operating Controls
BREWING COFFEE
Prepare the Brew Baskets:
Make sure a bypass diverter is properly installed in each
brew chamber.
Insert one (1) Bloomfield paper filter into each brew chamber.
Add a measured amount of grounds to each brew basket.
Gently shake the basket to level the grounds.
Slide one brew chamber under each brew head.
Fig. 5 Brew Basket
CAUTION:
BURN HAZARD
Insert Satellites:
Slide one satellite under each brew chamber until it is fully
seated.
Press appropriate WARMER SWITCH to ON.
Select Brew Volume:
Press VOLUME SELECT switch to 1 GAL or 1-1/2 GAL.
Start the Brew:
Press either the right or left START BREW key.
NOTE: The brew can be cancelled at any time by pressing
the BREW STOP key.
At the end of the brew, be sure all water has stopped dripping
before removing the brew chamber.
When the READY-TO-BREW light comes on, the brewer is
ready to run another brew cycle.
Empty the Brew Basket:
Discard the grounds and the paper filter. Rinse the brew
chamber under clear water.
9
Basket and contents are hot to
the touch and may cause burns
on contact.
CLEANING INSTRUCTIONS
CLEANING
INSTRUCTIONS
CAUTION:
Burn Hazard
Brewing and serving
temperatures of coffee are
extremely hot.
Hot coffee will cause
serious skin burns.
IMPORTANT:
DO NOT use steel wool, sharp
objects, or caustic, abrasive or
chlorinated cleansers to clean
the brewer, brew baskets or
satellites.
DO NOT immerse or submerge
satellites in water.
PROCEDURE: Clean Coffee Brewer
PRECAUTIONS: Press POWER key to OFF.
Allow brewer to cool.
FREQUENCY:
Daily
TOOLS:
Mild Detergent, Clean Soft Cloth or Sponge
Bristle Brush
1. Press POWER key to OFF.
Allow brewer to cool.
2. Remove satellites.
3. Remove and empty brew baskets.
4. Remove spray disks and gaskets from spray heads
5. Wipe inside of spray head and area around spray head with a
soft clean cloth or sponge moistened with clean water.
6. Wash spray disks in a sink using warm water and a mild
detergent. A bristle brush may be used to clear clogged
spray holes. Rinse spray disks with clean water and allow to
air dry.
7. Wash brew chambers in a sink using warm water and a mild
detergent. A bristle brush may be used to clean around the
bypass diverters. Rinse with clean water and allow to air dry.
Be sure bypass diverters are properly installed.
8. Remove and drain the drip tray. Rinse in a sink under warm
running water. Allow to air dry, then reinstall on brewer.
9. Wipe exterior of brewer and satellites with a soft clean cloth
or sponge moistened with clean water.
10. Reinstall gaskets INSIDE brew heads, then reinstall spray
disks.
11. Reinstall brew chambers.
12. Reinstall satellites.
Procedure is complete
10
CLEANING INSTRUCTIONS (continued)
PROCEDURE: Clean Satellite
PRECAUTIONS: Drain Satellite before Cleaning
FREQUENCY:
Twice Weekly
TOOLS:
Sight Glass Brush, Sanitizer
Soft Clean Cloth, Bucket
CAUTION:
Burn Hazard
Brewing and serving
temperatures of coffee are
extremely hot.
Hot coffee will cause
serious skin burns.
1. Remove and drain satellites. Remove lids.
2. Place 1 packet of Sanitizer into 2-1/2 gallons of warm tap
water. Pour approximately 1 gallon of sanitizer solution into
each satellite. Allow to stand for 2 minutes.
3. Drain sanitizer solution from satellite into the bucket.
4. Disassemble faucet. Brush clean with sanitizer solution.
Reassemble faucet.
IMPORTANT:
DO NOT submerge satellite in
water.
IMPORTANT:
DO NOT use steel wool, sharp
objects, or caustic, abrasive or
chlorinated cleansers to clean
the satellites.
5. If necessary, disassemble and clean sight glass.
a. Push down on ears on sight glass guard . Then, pull
ears forward. Lift guard off of retaining clip.
b. Remove sight glass tube from silicone elbow. Run the
sight glass brush through the tube at least ten times.
c. Reassemble the tube to the silicone elbow. Be sure the
elbow has not been pulled from the satellite body.
d. Reinstall the sight glass guard.
6. Reinstall lids. Install satellites on brewer.
7. Rinse satellites: With an empty brew chamber in place, press
the BREW key and run 1 full cycle into each satellite.
8. Drain water from satellites.
Procedure is complete
Sight Glass
11
SERVICING INSTRUCTIONS
CAUTION CHEMICAL BURN
HAZARD
Deliming chemicals are caustic.
Wear appropriate protective
gloves and goggles during this
procedure.
Never siphon deliming
chemicals or solutions by
mouth.
This operation should only be
performed by qualified and experienced service personnel.
IMPORTANT: DO NOT spill,
splash or pour water or deliming
solution into or over any internal
component other than the inside
of the water tank.
IMPORTANT: DO NOT allow
any internal components to
come into contact with the
deliming solution. Take care to
keep all internal components
dry.
NOTE: Repeat steps 4 and 7
as required to remove all buildup.
PROCEDURE: Delime the Water Tank
PRECAUTIONS: Disconnect brewer from electric power.
Allow brewer to cool.
FREQUENCY:
As required (Brewer slow to heat)
TOOLS:
Deliming Solution
Protective Gloves, Goggles & Apron
Mild Detergent, Clean Soft Cloth or Sponge
Bristle Brush, Bottle Brush
Large Sink (or other appropriate work area)
1.
Disconnect brewer from the electrical supply.
2.
Remove the brewer top panel, then remove the tank lid
assembly. Do not disconnect the tank assembly at this
time.
3.
Siphon all water from the hot water tank.
4.
Mix 10 gallons of deliming solution according to the
manufacturer’s directions. Carefully pour the deliming
solution into the water tank. Lower the lid assembly back
onto the tank. Allow to sit for 30 minutes, or as directed by
the chemical manufacturer.
5.
At end of soaking period, reconnect brewer to electrical
power. Install the brew chamber without filter paper or
grounds. Place an empty satellite under the brew
chamber. Force a 1-1/2 gallon brew:
a. Press the 1-1/2 gallon key
b. Press the brew key, then press and hold the brew key
until a brew is initiated.
Empty the satellite and repeat for the other side.
6.
Disconnect brewer from electrical power and allow to cool.
7.
Remove lid assembly from tank.
a. Using a stiff bristle brush, scrub internal components to
remove lime and calcium build-up.
b. Thoroughly rinse internal components of lid assembly
with clear water.
c. Store lid assembly in a safe location.
8.
Using a stiff bristle brush, scrub exposed portions of the
heating element and the inside surfaces of the tank to
remove lime and calcium build-up.
9.
Siphon all solution from the tank.
12
SERVICING INSTRUCTIONS (continued)
10.
Reinstall tank lid assembly into hot water tank. Make sure
the lid gasket is properly in place, then reinstall the holddown clamps.
11.
Remove spray disks and gaskets. Rinse both brew heads
with clean water. Using a stiff brush, scrub spray disk to
remove any lime or calcium build-up. Reinstall gaskets
and spray disks.
13.
Reconnect brewer to electrical supply .
14.
Install the brew chamber without filter paper or grounds.
15.
Place an empty satellite under the brew chamber. Run at
least five 1-1/2 gallon brew cycles and discard all water
generated at the end of each cycle.
Repeat for the other side.
16.
Rinse satellite with clean water. Reinstall one empty
satellite under each brew chamber.
Brewer is ready to use.
13
NOTE: Normally, silicone
hoses do not need to be
delimed. Should deliming
hoses become necessary,
Bloomfield recommends
replacing the hoses.
SERVICING INSTRUCTIONS (continued)
CAUTION:
SHOCK HAZARD
Disconnect brewer from electric
power before opening the
access panel.
Adjustments to be performed by
qualified technician only.
NOTE:
Brewer is pre-adjusted to deliver
1 and 1-1/2 gallons of coffee at
a water pressure of 50 p.s.i.
Use this procedure to adjust the
delivered volume to suit local
conditions.
TIMER ADJUSTMENT
PRECAUTIONS: Disconnect brewer from electric power.
Allow brewer to cool.
FREQUENCY:
As required to adjust delivered volume
TOOLS:
Phillips head screwdriver
Satellite or other container to calibrate volume
1. Press HEATER ON/OFF switch to OFF. Turn POWER
switch on back of brewer OFF.
2. Remove TOP PANEL. Operating controls are accessible
through the top panel only.
3. Adjust the TIMER setting.
NOTE: Each side has its own timer. The LEFT TIMER is for
the LEFT SIDE; the RIGHT TIMER is for the RIGHT SIDE.
Turn CLOCKWISE to increase time;
Turn COUNTER-CLOCKWISE to decrease time.
Adjust only in small increments to avoid large volume
variations. Recommend no more than 1/16 turn.
4. Replace TOP PANEL. Turn POWER switch ON. Press
HEATER ON/OFF switch to ON.
5. Allow the brewer to come up to brewing temperature, then
perform a test brew. Check delivered volume. Readjust as
necessary.
When desired volume is achieved, procedure is complete.
14
SERVICING INSTRUCTIONS (continued)
TEMPERATURE ADJUSTMENT
PRECAUTIONS: Disconnect brewer from electric power.
Allow brewer to cool.
FREQUENCY:
As required to adjust delivered volume
TOOLS:
Phillips head screwdriver
Satellite or other container to calibrate volume
1. Press HEATER ON/OFF switch to OFF. Turn POWER
switch on back of brewer OFF.
2. Remove TOP PANEL. Operating controls are accessible
through the top panel only.
3. Remove one of the plugs in the tank cover and insert a
thermometer of known accuracy.
4. Locate the CONTROL THERMOSTAT on the right side of the
top housing:
Turn CLOCKWISE to increase temperature
Turn COUNTER-CLOCKWISE to decrease temperature
1/8 turn is equal to approximately 10ºF change.
5. Turn POWER switch ON. Press HEATER ON/OFF switch to
ON.
6. Allow the brewer to come up to brewing temperature. When
READY-TO -BREW light comes on, check temperature on
thermometer. Readjust thermostat as necessary.
7. When desired temperature is achieved, remove thermometer,
replace tank plug and reinstall top panel.
Procedure is complete
15
CAUTION:
SHOCK HAZARD
Live electrical circuits are
exposed during this procedure.
Use care to avoid uninsulated
electrical connectors.
Adjustments to be performed by
qualified technician only.
NOTE:
1/8 turn = approx 10ºF (5.5ºC)
TROUBLESHOOTING SUGGESTIONS
DESCRIPTION OF PROBLEM
POSSIBLE CAUSE
SUGGESTED REMEDY
No lights or heat
Unit not plugged in or circuit
breaker tripped
Restore electric power
Power switch OFF
Turn power switch ON
Hi-limit safety tripped
Allow brewer to cool, verify water
level, reset hi-limit
Thermostat damaged
Replace thermostat
Damaged hi-limit safety
Replace hi-limit
Damaged heater switch
Replace heater switch
Damaged heating element
Replace heating element
Water level probe corroded
Clean water level probe
Poor ground connection
Verify ground connection
Dirt in inlet valve or valve
damaged
Replace inlet valve
Brew valve damaged
Replace brew valve
Tank water boiling
Adjust or replace thermostat
Too many paper filters or wrong
filter used.
Use one genuine Bloomfield
paper filter per brew
Chamber discharge hole
plugged
Clean brew chamber
Timer not set properly
Set timer
Too much coffee or too fine a
grind
Check with coffee supplier for
recommended grind and quantity
Connected to wrong voltage
Verify supply voltage
Scale build-up on heating
elements
De-lime hot water tank
Damaged heating element
Replace element
Insufficient water pressure
Brewer must be operated on a
dedicated water line. Other
equipment on line may be
robbing water volume.
Plugged water line strainer
Clean strainer
Warmer switch not on
Turn warmer switch on
Damaged element or wiring
Replace as required
No heat
Brewer overflows
Brew chamber overflows
Heats slow
Slow to fill
No heat to satellite
Poor coffee quality
Keep brewer and servers clean.
Install a taste and odor filter in water supply, and replace
cartridges regularly.
Use a quality coffee with a consistent roast. Use proper grind and
amount of coffee per brew.
16
SATELLITE EXPLODED VIEW & PARTS LIST
SATELLITE MODEL 9440
4.3
4.1
4.2
2
4.8
4.7
4.6
4.5
4.4
4.10
PART OF
ITEM 4
6
7
5
9 4 PL
1
11
8
10 2 PL
4
3
ITEM PART NO.
1
2
83863
3
84313
4
86577
4.1
86600
4.2
8700-25L
4.3
84392
4.4
84394
4.5
8600-26
4.6
84395
4.7
84489
4.8
84488
4.10 84396
5
84299
6
84300
7
84354
8
8043-13
9
10
11
DESCRIPTION
WELDMENT, SATELLITE
TANK LID ASSY
HANDLE / FAUCET GUARD
FAUCET & SHANK ASSY
FAUCET, MODEL ESP
SEAT CUP, #3S10
HANDLE, #13SBE-SNAP
C-RING #18-1
NUT HEX
SHANK
WASHER, FIBRE
FERRULE
SHANK ASSY
HOUSING, SIGHT GAUGE
BRACKET, SIGHT GAUGE
TUBE, SIGHT GAUGE
ELBOW
SCREW, 8A x 1/2 TRS HD ST BLK
SCREW, 8A x 1/2 TRS HD ST SS
DECAL, SATELLITE
17
QTY
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
4
2
1
EXPLODED VIEW
CABINET AND EXTERIOR COMPONENTS
18
PARTS LIST CABINET AND EXTERIOR COMPONENTS
QTY
ITEM
STRAIN RELIEF
1
31
WARMER BASE
1
55485
NUT HEX 1/4-20 SS
2
32
HOUSING UPPER ASSY
1
60310
TERMINAL BLOCK 3P
1
33
SWITCH ROCKER HI-TEMP
2
4
BRACKET THERMOSTAT
1
34
SCREW 8A x 1/2 TR TAP SS
40
5
LUG GROUND SOLDERLESS
1
35
82533
BREW CHAMBER ASSY .25 HOLE
ITEM
P/N
1
9012-38
2
3
DESCRIPTION
P/N
84382
DESCRIPTION
6
55736
NUT KEP 8-32 GREEN
1
35a
32387
BREW CHAMBER ONLY
7
85235
BUTTON PLUG BLK PLASTIC
1
35b
8707-2
HANDLE BREW CHAMBER BLK
8
8533-32
ELEMENT WARMER 240V 100W
2
35c
8706-9
WIRE RACK BREW CHAMBER
9
503141
CONTROL BOARD LIQ LEVEL
1
35d
8707-3
SCREW BREW CHAMBER
GUIDE, SATELLITE
2
35e
8812-73
CLIP BREW CHAMBER
10
QTY
O
P
T
I
O
N
A
L
11
8703-26
RETAINER WARMER ELEMENT
2
36
86652
BREW CHAMBER ASSY
12
7200-6X
SCREW 8-32 x 5/16 PHL SS
2
36a
86651
DIVERTER BYPASS
13
82215
GASKET SPRAYHEAD 1.5 ID
2
41
8738-2
LIGHT PILOT GREEN 250V
1
14
82727
DISK SPRAY HEAD EMBOSSED
2
42
WASHER FLAT #4
4
15
83098
LEG 4" BLK PLASTIC
4
43
57780
CONTACTOR 3P 240V 40A
2
16
83107
FEET RUBBER BLK
4
44
83885
DRIP SHIELD
2
17
84604
DECAL CONTROL PANEL
1
45
83794
FUSE 5A
2
BRACKET TOP TANK SUPPORT
2
46
83795
FUSE HOLDER
2
18
2
19
84620
SWITCH LIGHTED OFF MOM ON
2
47
83793
WASHER 1.50 O.D.
2
20
84621
SWITCH 2P ON MOM OFF 10A
2
48
85760
SOLENOID SINGLE 240V 1.0 GPM
1
NUT KEP 8-32 SS
6
49
SCREW PAN 4mm x 6mm SS
2
21
22
84622
SWITCH 2P ON NONE ON 10A
2
50
STIFFENER, BOTTOM PLATE
2
23
82395
SWITCH LIGHTED 20A 250V
1
51
TANK SUPPORT
1
24
82936
SWITCH ROCKER ON-OFF
1
52
7506-39
SCREW 8-32 x 1/2 PH SS
2
25
LOWER HOUSING
1
53
83362
SPACER .17 I.D. x 1/4 LG
2
26
COVER TOP HOUSING
1
54
BRACKET, TIMER
2
27
FRONT PANEL
1
28
PLATE BOTTOM ASSY
1
29
BASE WRAP
1
TIMER FULL, 2/3, 1/3 230V
2
30
85123
19
EXPLODED VIEW
INTERIOR COMPONENTS
20
PARTS LIST INTERIOR COMPONENTS
ITEM
P/N
1
83778
2
DESCRIPTION
QTY
ITEM
P/N
RETAINING CLIP TANK LID
4
23
55485
NUT KEPS 8-32 SS
20
24
DESCRIPTION
QTY
NUT 1/4-20 (pk 100)
1
SCREW 8A x 1/2 TR TAP SS
4
3
8043-12
GASKET TANK COVER
1
25
86280
THERMOSTAT 15" CAP TUBE
1
4
8783-1
FAUCET HOT WATER
1
26
83414
SHIELD HI-LIMIT THERMO
1
BRACKET OUTLET VALVE
2
27
83415
NUT 6-32 x 1" LG
2
83571
INSERT SPRAY HEAD SS2
2
WASHER FLAT #8 SS
2
5
6
83521
PROBE ASSY WATER LEVEL
1
28
7
83532
SLEEVE WATER LEVEL PROBE
1
29
8
82390
GROMMET .312 ID
1
30
3-100
SCREW 6-32 x 1/4 SS
4
9
83978
TUBE SILICONE .312 x 30"
1
31
85289
STRAP, TIE-DOWN
1
10
83152
ELBOW SPRAYER
2
32
86574
TUBE BYPASS
2
TANK ASSY
1
33
86582
TEE REDUCING
2
11
12
84923
ELEMENT 3000W 240V
2
34
86773
TUBE SILICONE .312 ID x 1.5"
2
13
83309
GASKET TANK HEATER
2
35
83538
TUBE SILICONE .312 ID x 10"
2
14
84343
FILL TUBE 90º BEND
1
36
BLANKING PLATE
1
15
83312
THERMOSTAT HI-LIMIT 2P
1
37
BRACKET TERMINAL BLOCK
1
TANK LID ASSY
1
38
8552-18
TERMINAL BLOCK
1
TUBE SILICONE .50 ID x 4.25
2
39
616-5
SCREW 6-32 x 3/4
4
ELBOW OUTLET
2
40
84435
INSULATION, FAUCET TUBE
2
16
17
84630
18
8043-11
19
83384
TUBE VENT EXTENSION
4
41
82724
TUBE, SILICONE .312 ID x 4”
1
20
83537
TUBE SILICONE 9"
1
42
84434
TUBE FORMED SS
1
21
84619
VALVE DISPENSING ADJUST
2
43
84433
TUBE, SILICONE .312 ID x 6”
22
82148
LOCK WASHER
1
21
WIRING DIAGRAM
22
WATER FLOW DIAGRAM
WATER FLOW
INLET
The INLET VALVE is controlled by a signal from the CONTROL
BOARD. If the WATER LEVEL PROBE does not detect water, the inlet
solenoid is opened until water is again sensed.
The 9221-Series of
brewers have two
independent brewing
systems sharing a
common hot water tank.
BREW AND BYPASS
The BREW VALVE fed by gravity from the hot water tank. The brew
valve is opened for a length of time as determined by the TIMER
setting. The brew valve discharged through the BREW HEAD in two
ways:
A portion of water is fed to the BYPASS through a reducing "tee".
The amount of bypass water is controlled by the opening size of the
leg of the "tee". Bypass water flows through the brew basket, but
is diverted from the grounds by a bypass channel.
The remainder of the brew water is discharged through the SPRAY
DISK and flows over the grounds in the brew basket.
Each half of the brewer is independently controlled.
HOT WATER FAUCET
The HOT WATER FAUCET is fed by gravity from the hot water tank.
The faucet is spring-loaded closed and manually opened.
23
The hot water faucet is fed
by the hot water tank, but
is otherwise independent of
the brewing systems.
NOTE:
Use of the hot water faucet
during a brew cycle will
not change the delivered
volume. However,
excessive use of the faucet
during brew may lower the
brew water temperature.
Bloomfield Industries proudly supports CFESA
Commercial Food Equipment Service Association
Bloomfield Industries, Inc.
Division of Carrier Commercial Refrigeration
In US and Canada
Telephone: 775-689-5700
Fax:
888-492-2783
Fax:
800-356-5142 (for orders only)
website: www.wellsbloomfield.com